RADEXT Working Group A. DeKok
Internet-Draft FreeRADIUS
Intended status: Informational 8 January 2024
Expires: 11 July 2024
RADIUS and TLS-PSK
draft-ietf-radext-tls-psk-05
Abstract
This document gives implementation and operational considerations for
using TLS-PSK with RADIUS/TLS (RFC6614) and RADIUS/DTLS (RFC7360).
About This Document
This note is to be removed before publishing as an RFC.
Status information for this document may be found at
https://datatracker.ietf.org/doc/draft-ietf-radext-tls-psk/.
Discussion of this document takes place on the RADEXT Working Group
mailing list (mailto:radext@ietf.org), which is archived at
https://mailarchive.ietf.org/arch/browse/radext/. Subscribe at
https://www.ietf.org/mailman/listinfo/radext/.
Source for this draft and an issue tracker can be found at
https://github.com/freeradius/radext-tls-psk.git.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 11 July 2024.
DeKok Expires 11 July 2024 [Page 1]
Internet-Draft RADIUS and TLS-PSK January 2024
Copyright Notice
Copyright (c) 2024 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Revised BSD License text as
described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Revised BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. History . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. General Discussion of PSKs and PSK Identities . . . . . . . . 4
4.1. Requirements on PSKs . . . . . . . . . . . . . . . . . . 4
4.1.1. Interaction between PSKs and RADIUS Shared Secrets . 6
4.2. PSK Identities . . . . . . . . . . . . . . . . . . . . . 7
4.2.1. Security of PSK Identities . . . . . . . . . . . . . 7
4.3. PSK and PSK Identity Sharing . . . . . . . . . . . . . . 8
5. Guidance for RADIUS Clients . . . . . . . . . . . . . . . . . 8
5.1. PSK Identities . . . . . . . . . . . . . . . . . . . . . 9
6. Guidance for RADIUS Servers . . . . . . . . . . . . . . . . . 10
6.1. Current Practices . . . . . . . . . . . . . . . . . . . . 10
6.2. Practices for TLS-PSK . . . . . . . . . . . . . . . . . . 11
6.2.1. IP Filtering . . . . . . . . . . . . . . . . . . . . 12
6.2.2. PSK Authentication . . . . . . . . . . . . . . . . . 14
6.2.3. Resumption . . . . . . . . . . . . . . . . . . . . . 14
6.2.4. Interaction with other TLS authentication methods . . 15
7. Privacy Considerations . . . . . . . . . . . . . . . . . . . 16
8. Security Considerations . . . . . . . . . . . . . . . . . . . 16
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 16
10. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 16
11. Changelog . . . . . . . . . . . . . . . . . . . . . . . . . . 16
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 16
12.1. Normative References . . . . . . . . . . . . . . . . . . 16
12.2. Informative References . . . . . . . . . . . . . . . . . 17
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 18
DeKok Expires 11 July 2024 [Page 2]
Internet-Draft RADIUS and TLS-PSK January 2024
1. Introduction
The previous specifications "Transport Layer Security (TLS)
Encryption for RADIUS" [RFC6614] and "Datagram Transport Layer
Security (DTLS) as a Transport Layer for RADIUS" [RFC7360] defined
how (D)TLS can be used as a transport protocol for RADIUS. However,
those documents do not provide guidance for using TLS-PSK with
RADIUS. This document provides that missing guidance, and gives
implementation and operational considerations.
Unless it is explicitly called out that a recommendation applies to
TLS alone or to DTLS alone, each recommendation applies to both TLS
and DTLS.
This document uses "shared secret" to mean "RADIUS shared secret",
and Pre-Shared Key (PSK) to mean secrets which are used with TLS-PSK.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. History
TLS deployments usually rely on certificates in most common uses.
However, we recognize that it may be difficult to fully upgrade
client implementations to allow for certificates to be used with
RADIUS/TLS and RADIUS/DTLS. These upgrades involve not only
implementing TLS, but can also require significant changes to
administration interfaces and application programming interfaces
(APIs) in order to fully support certificates.
For example, unlike shared secrets, certificates expire. This
expiration means that a working system using TLS can suddenly stop
working. Managing this expiration can require additional
notification APIs on RADIUS clients and servers which were previously
not required when shared secrets were used.
Certificates also require the use of certification authorities (CAs),
and chains of certificates. RADIUS implementations using TLS
therefore have to track not just a small shared secret, but also
potentially many large certificates. The use of TLS-PSK can
therefore provide a simpler upgrade path for implementations to
transition from RADIUS shared secrets to TLS.
DeKok Expires 11 July 2024 [Page 3]
Internet-Draft RADIUS and TLS-PSK January 2024
4. General Discussion of PSKs and PSK Identities
Before we define any RADIUS-specific use of PSKs, we must first
review the current standards for PSKs, and give general advice on
PSKs and PSK identities.
The requirements in this section apply to both client and server
implementations which use TLS-PSK. Client-specific and server-
specific issues are discussed in more detail later in this document.
4.1. Requirements on PSKs
Reuse of a PSK in multiple versions of TLS (e.g. TLS 1.2 and TLS
1.3) is considered unsafe ([RFC8446], Appendix E.7). Where TLS 1.3
binds the PSK to a particular key derivation function, TLS 1.2 does
not. This binding means that it is possible to use the same PSK in
different hashes, leading to the potential for attacking the PSK by
comparing the hash outputs. While there are no known insecurities,
these uses are not known to be secure, and should therefore be
avoided.
[RFC9258] adds a key derivation function to the import interface of
(D)TLS 1.3, which binds the externally provided PSK to the protocol
version. In particular, that document:
... describes a mechanism for importing PSKs derived from external
PSKs by including the target KDF, (D)TLS protocol version, and an
optional context string to ensure uniqueness. This process yields
a set of candidate PSKs, each of which are bound to a target KDF
and protocol, that are separate from those used in (D)TLS 1.2 and
prior versions. This expands what would normally have been a
single PSK and identity into a set of PSKs and identities.
An implementation MUST NOT use the same PSK for TLS 1.3 and for
earlier versions of TLS. This requirement prevents reuse of a PSK
with multiple TLS versions, which prevents the attacks discussed in
[RFC8446], Appendix E.7. The exact manner in which this requirement
is enforced is implementation-specific. One possibility is to have
two different PSKs. Another possibility is to forbid the use of TLS
1.3, or to forbid the use of TLS versions less than TLS 1.3.
It is RECOMMENDED that systems follow the directions of [RFC9257],
Section 6 for the use of external PSKs in TLS. That document
provides extremely useful guidance on generating and using PSKs.
Implementations MUST support PSKs of at least 32 octets in length,
and SHOULD support PSKs of 64 octets or more. As the PSKs are
generally hashed before being used in TLS, the useful entropy of a
DeKok Expires 11 July 2024 [Page 4]
Internet-Draft RADIUS and TLS-PSK January 2024
PSK is limited by the size of the hash output. This output may be
256, 384, or 512 bits in length. Never the less, it is good practice
for implementations to allow entrty of PSKs of more than 64 octets,
as the PSK may be in a form other than bare binary data.
Implementations which limit the PSK to a maximum of 64 octets are
likely to use PSKs which have much less than 512 bits of entropy.
That is, a PSK with high entropy may be expanded via some construct
(e.g. base32 as in the example below) in order to make it easier for
people to interact with. Where 512 bits of entropy are input to an
encoding construct, the output may be larger than 64 octets.
Implementations MUST require that PSKs be at least 16 octets in
length, which SHOULD be derived from a source with at least 128 bits
of entropy. That is, short PSKs MUST NOT be permitted to be used,
and PSKs MUST be uniformly random. The strength of the PSK is not
determined by the length of the PSK, but instead by the number of
bits of entropy which it contains. People are not good at creating
data with high entropy, so a source of cryptographically secure
random numbers MUST be used.
Administrators SHOULD use PSKs of at least 24 octets, generated using
a source of cryptographically secure random numbers. Implementers
needing a secure random number generator should see [RFC8937] for for
further guidance. PSKs are not passwords, and administrators should
not try to manually create PSKs.
Passwords are generally intended to be remembered and entered by
people on a regular basis. In contrast, PSKs are intended to be
entered once, and then automatically saved in a system configuration.
As such, due to the limited entropy of passwords, they are not
acceptable for use with TLS-PSK, and would only be acceptable for use
with a password-authenticated key exchange (PAKE) TLS method
[RFC8492].
We also incorporate by reference the requirements of [RFC7360],
Section 10.2 when using PSKs.
In order to guide Implementers, we give an example script below which
generates random PSKs. While the script is not portable to all
possible systems, the intent here is to document a concise and simple
method for creating PSKs which are both secure, and humanly
manageable.
#!/usr/bin/env perl use MIME::Base32; use Crypt::URandom(); print
join('-', unpack("(A4)*", lc
encode_base32(Crypt::URandom::urandom(16)))), "\n";
DeKok Expires 11 July 2024 [Page 5]
Internet-Draft RADIUS and TLS-PSK January 2024
This script reads 128 bits (16 octets) of random data from a secure
source, encodes it in Base32, and then formats it to be more humanly
manageable. The generated keys are of the form "yttb-4gv2-ynfk-jbjh-
2dja-cj7e-am". This form of PSK will be accepted by any
implementation which supports at least 32 octets for PSKs. Larger
PSKs can be generated by passing larger values to the "urandom()"
function. The above derivation assumes that the random source
returns one bit of entropy for every bit of randomness which is
returned. Sources failing that assumption are NOT RECOMMENDED.
4.1.1. Interaction between PSKs and RADIUS Shared Secrets
Any shared secret used for RADIUS/UDP or RADIUS/TLS MUST NOT be used
for TLS-PSK.
It is RECOMMENDED that RADIUS clients and servers track all used
shared secrets and PSKs, and then verify that the following
requirements all hold true:
* no shared secret is used for more than one RADIUS client
* no PSK is used for more than one RADIUS client
* no shared secret is used as a PSK
Note that the shared secret of "radsec" given in [RFC6614] can be
used across multiple clients, as that value is mandated by the
specification. The intention here is to recommend best practices for
administrators who enter site-local shared secrets.
There may be use-cases for using one shared secret across multiple
RADIUS clients. There may similarly be use-cases for sharing a PSK
across multiple RADIUS clients. Details of the possible attacks on
reused PSKs are given in [RFC9257], Section 4.1.
There are few, if any, use-cases for using a PSK as a shared secret,
or vice-versa.
Implementations SHOULD NOT provide user interfaces which allow both
PSKs and shared secrets to be entered at the same time. There is too
much of a temptation for administrators to enter the same value in
both fields, which would violate the limitations given above.
Implementations MUST NOT use a "shared secret" field as a way for
administrators to enter PSKs. The PSK entry fields MUST be labeled
as being related to PSKs, and not to shared secrets.
DeKok Expires 11 July 2024 [Page 6]
Internet-Draft RADIUS and TLS-PSK January 2024
4.2. PSK Identities
It is RECOMMENDED that systems follow the directions of [RFC9257],
Section 6.1.1 for the use of external PSK Identities in TLS. Note
that the PSK identity is sent in the clear, and is therefore visible
to attackers. Where privacy is desired, the PSK identity could be
either an opaque token generated cryptographically, or perhaps in the
form of a Network Access Identifier (NAI) [RFC7542], where the "user"
portion is an opaque token. For example, an NAI could be
"68092112@example.com". If the attacker already knows that the
client is associated with "example.com", then using that domain name
in the PSK identity offers no additional information. In contrast,
the "user" portion needs to be both unique to the client and private,
so using an opaque token there is a more secure approach.
Implementations MUST support PSK Identities of 128 octets, and SHOULD
support longer PSK identities. We note that while TLS provides for
PSK identities of up to 2^16-1 octets in length, there are few
practical uses for extremely long PSK identities.
4.2.1. Security of PSK Identities
We note that the PSK identity is a field created by the connecting
client. Since the client is untrusted until both the identity and
PSK have been verified, both of those fields MUST be treated as
untrusted. That is, a well-formed PSK Identity is likely to be in
UTF-8 format, due to the requirements of [RFC4279], Section 5.1.
However, implementations MUST support managing PSK identities as a
set of undistinguished octets.
It is not safe to use a raw PSK Identity to look up a corresponding
PSK. The PSK may come from an untrusted source, and may contain
invalid or malicious data. For example, the identity may have
incorrect UTF-8 format; or it may contain data which forms an
injection attack for SQL, LDAP, REST or shell meta characters; or it
may contain embedded NUL octets which are incompatible with APIs
which expect NUL terminated strings. The identity may also be up to
65535 octets long.
As such, implementations MUST validate the identity prior to it being
used as a lookup key. When the identity is passed to an external API
(e.g. database lookup), implementations MUST either escape any
characters in the identity which are invalid for that API, or else
reject the identity entirely. The exact form of any escaping depends
on the API, and we cannot document all possible methods here.
However, a few basic validation rules are suggested, as outlined
below. Any identity which is rejected by these validation rules
SHOULD cause the server to close the TLS connection.
DeKok Expires 11 July 2024 [Page 7]
Internet-Draft RADIUS and TLS-PSK January 2024
The suggested validation rules for identies used outside of
resumption are as follows:
* Identities longer than a fixed maximum SHOULD be rejected. The
limit is implementation dependent, but SHOULD NOT be less than
128, and SHOULD NOT be more than 1024.
* Identities SHOULD be in UTF-8 format. Identities with embedded
control characters, NUL octets, etc. SHOULD NOT be used.
* Where the NAI format is expected, identities which are not in NAI
format SHOULD be rejected
It is RECOMMENDED that implementations extend these rules with any
additional validation which are found to be useful. For example,
implementations and/or deployments could both generate PSK identities
in a particular format for passing to client systems, and then also
verify that any received identity matches that format. For example,
a site could generate PSK identities which are composed of characters
in the local language. The site could then reject identities which
contain characters from other languages, even if those characters are
valid UTF-8.
4.3. PSK and PSK Identity Sharing
While administrators may desire to share PSKs and/or PSK identities
across multiple systems, such usage is NOT RECOMMENDED. Details of
the possible attacks on reused PSKs are given in [RFC9257],
Section 4.1.
Implementations MUST be able to configure a unique PSK and PSK
identity for each possible client-server relationship. This
configuration allows administrators desiring security to use unique
PSKs for each such relationship. This configuration also allows
administrators to re-use PSKs and PSK Identities where local policies
permit.
Implementations SHOULD warn administrators if the same PSK identity
and/or PSK is used for multiple client-server relationships.
5. Guidance for RADIUS Clients
Client implementations MUST allow the use of a pre-shared key (TLS-
PSK) for RADIUS/TLS. The client implementation can then expose a
user interface flag which is "TLS yes / no", and then also fields
which ask for the PSK identity and PSK itself.
DeKok Expires 11 July 2024 [Page 8]
Internet-Draft RADIUS and TLS-PSK January 2024
For TLS 1.3, Implementations MUST support "psk_dhe_ke" Pre-Shared Key
Exchange Mode in TLS 1.3 as discussed in [RFC8446], Section 4.2.9 and
in [RFC9257], Section 6. Implementations MUST implement the
recommended cipher suites in [RFC9325], Section 4.2 for TLS 1.2, and
in [RFC8446], Section 9.1 for TLS 1.3. In order to future-proof
these recommendations, we give the following recommendations:
* Implementations SHOULD use the "Recommended" cipher suites listed
in the IANA "TLS Cipher Suites" registry,
- for TLS 1.3, the use "psk_dhe_ke" PSK key exchange mode,
- for TLS 1.2 and earlier, use cipher suites which require
ephemeral keying.
If a client initiated a connection using a PSK with TLS 1.3 by
including the pre-shared key extension, it MUST close the connection
if the server did not also select the pre-shared key to continue the
handshake.
5.1. PSK Identities
[RFC6614] is silent on the subject of PSK identities, which is an
issue that we correct here. Guidance is required on the use of PSK
identities, as the need to manage identities associated with PSK is a
new requirement for NAS management interfaces, and is a new
requirement for RADIUS servers.
RADIUS systems implementing TLS-PSK MUST support identities as per
[RFC4279], Section 5.3, and MUST enable configuring TLS-PSK
identities in management interfaces as per [RFC4279], Section 5.4.
The historic methods of signing RADIUS packets have not yet been
cracked, but they are believed to be much less secure than modern
TLS. Therefore, when a RADIUS shared secret is used to sign RADIUS/
UDP or RADIUS/TCP packets, that shared secret MUST NOT be used with
TLS-PSK. If the secrets were to be reused, then an attack on
historic RADIUS cryptography could be trivially leveraged to decrypt
TLS-PSK sessions. Therefore in order to prevent confusion between
shared secrets and TLS-PSKs, management interfaces and APIs need to
label PSK fields as "PSK" or "TLS-PSK", rather than as "shared
secret".
With TLS-PSK, RADIUS/TLS clients MUST permit the configuration of a
RADIUS server IP address or host name, because dynamic server lookups
[RFC7585] can only be used if servers use certificates.
DeKok Expires 11 July 2024 [Page 9]
Internet-Draft RADIUS and TLS-PSK January 2024
6. Guidance for RADIUS Servers
In order to support clients with TLS-PSK, server implementations MUST
allow the use of a pre-shared key (TLS-PSK) for RADIUS/TLS.
For TLS 1.3, Implementations MUST support "psk_dhe_ke" Pre-Shared Key
Exchange Mode in TLS 1.3 as discussed in [RFC8446], Section 4.2.9 and
in [RFC9257], Section 6. Implementations MUST implement the
recommended cipher suites in [RFC9325], Section 4.2 for TLS 1.2, and
in [RFC8446], Section 9.1 for TLS 1.3. In order to future-proof
these recommendations, we give the following recommendations:
* Implementations SHOULD use the "Recommended" cipher suites listed
in the IANA "TLS Cipher Suites" registry,
- for TLS 1.3, the use "psk_dhe_ke" PSK key exchange mode,
- for TLS 1.2 and earlier, use cipher suites which require
ephemeral keying.
The following section(s) describe guidance for RADIUS server
implementations and deployments. We first give an overview of
current practices, and then extend and/or replace those practices for
TLS-PSK.
6.1. Current Practices
RADIUS identifies clients by source IP address ([RFC2865] and
[RFC6613]) or by client certificate ([RFC6614] and [RFC7585]).
Neither of these approaches work for TLS-PSK. This section describes
current practices and mandates behavior for servers which use TLS-
PSK.
A RADIUS/UDP server is typically configured with a set of information
per client, which includes at least the source IP address and shared
secret. When the server receives a RADIUS/UDP packet, it looks up
the source IP address, finds a client definition, and therefore the
shared secret. The packet is then authenticated (or not) using that
shared secret.
That is, the IP address is treated as the clients identity, and the
shared secret is used to prove the clients authenticity and shared
trust. The set of clients forms a logical database "client table",
with the IP address as the key.
A server may be configured with additional site-local policies
associated with that client. For example, a client may be marked up
as being a WiFi Access Point, or a VPN concentrator, etc. Different
DeKok Expires 11 July 2024 [Page 10]
Internet-Draft RADIUS and TLS-PSK January 2024
clients may be permitted to send different kinds of requests, where
some may send Accounting-Request packets, and other clients may not
send accounting packets.
6.2. Practices for TLS-PSK
We define practices for TLS-PSK by analogy with the RADIUS/UDP use-
case, and by extending the additional policies associated with the
client. The PSK identity replaces the source IP address as the
client identifier. The PSK replaces the shared secret as proof of
client authenticity and shared trust. However, systems implementing
RADIUS/TLS [RFC6614] and RADIUS/DTLS [RFC7360] MUST still use the
shared secret as discussed in those specifications. Any PSK is only
used by the TLS layer, and has no effect on the RADIUS data which is
being transported. That is, the RADIUS data transported in a TLS
tunnel is the same no matter if client authentication is done via PSK
or by client certificates. The encoding of the RADIUS data is
entirely unaffected by the use (or not) of PSKs and client
certificates.
In order to securely support dynamic source IP addresses for clients,
we also require that servers limit clients based on a network range.
The alternative would be to suggest that RADIUS servers allow any
source IP address to connect and try TLS-PSK, which could be a
security risk. When RADIUS servers do no source IP address
filtering, it is easier for attackers to send malicious traffic to
the server. An issue with a TLS library or even a TCP/IP stack could
permit the attacker to gain unwarranted access. In contrast, when IP
address filtering is done, attackers generally must first gain access
to a secure network before attacking the RADIUS server.
Even where [RFC7585] dynamic discovery is not used, servers SHOULD
NOT permit TLS-PSK to be used across the wider Internet. The intent
for TLS-PSK is for it to be used in internal / secured networks,
where clients come from a small number of known locations. In
contrast, certificates can be generated and assigned to clients
without any interaction with the RADIUS server. Therefore if the
RADIUS server needs to accept connections from clients at unknown
locations, a more secure method is to use client certificates.
If a client system is compromised, its complete configuration is
exposed to the attacker. Exposing a client certificate means that
the attacker can pretend to be the client. In contrast, exposing a
PSK means that the attacker can not only pretend to be the client,
but can also pretend to be the server.XXX
DeKok Expires 11 July 2024 [Page 11]
Internet-Draft RADIUS and TLS-PSK January 2024
The benefits of TLS-PSK are in easing management and in administative
overhead, not in securing traffic from resourceful attackers. Where
TLS-PSK is used across the Internet, PSKs MUST contain at least 256
bits of entropy.
For example, a RADIUS server could be configured to be accept
connections from a source network of 192.0.2.0/24. The server could
therefore discard any TLS connection request which comes from a
source IP address outside of that network. In that case, there is no
need to examine the PSK identity or to find the client definition.
Instead, the IP source filtering policy would deny the connection
before any TLS communication had been performed.
RADIUS servers need to be able to limit certain PSK identifiers to
certain network ranges or IP addresses. That is, if a NAS is known
to have a dynamic IP address within a particular subnet, the server
should limit use of the NASes PSK to that subnet. This filtering can
therefore help to catch configuration errors.
As some clients may have dynamic IP addresses, it is possible for a
one PSK identity to appear at different source IP addresses over
time. In addition, as there may be many clients behind one NAT
gateway, there may be multiple RADIUS clients using one public IP
address. RADIUS servers need to support multiple PSK identifiers at
one source IP address.
That is, a server needs to support multiple different clients within
one network range, multiple clients behind a NAT, and one client
having different IP addresses over time. All of those use-cases are
common and necessary.
The following section describes these requirements in more detail.
6.2.1. IP Filtering
A server supporting this specification MUST perform IP address
filtering on incoming connections. There are few reasons for a
server to have a default configuration which allows connections from
any source IP address.
A TLS-PSK server MUST be configurable with a set of "allowed" network
ranges from which clients are permitted to connect. Any connection
from outside of the allowed range(s) MUST be rejected before any PSK
identity is checked. It is RECOMMENDED that servers support IP
address filtering even when TLS-PSK is not used.
DeKok Expires 11 July 2024 [Page 12]
Internet-Draft RADIUS and TLS-PSK January 2024
The "allowed" network ranges could be implemented as a global list,
or one or more network ranges could be tied to a client or clients.
The intent here is to allow connections to be filtered by source IP,
and to allow clients to be limited to a subset of network addresses.
The exact method and representation of that filtering is up to an
implementation.
Conceptually, the set of IP addresses and ranges, along with
permitted clients and their credentials forms a logical "client
table" which the server uses to both filter and authenticate clients.
The client table should contain information such as allowed network
ranges, PSK identity and associated PSK, credentials for another TLS
authentication method, or flags which indicate that the server should
require a client certificate.
Once a server receives a connection, it checks the source IP address
against the list of all allowed IP addresses or ranges in the client
table. If none match, the connection MUST be rejected. That is, the
connection MUST be from an authorized source IP address.
Once a connection has been established, the server MUST NOT process
any application data inside of the TLS tunnel until the client has
been authenticated. Instead, the server normally receives a TLS-PSK
identity from the client. The server then uses this identity to look
up the client in the client table. If there is no matching client,
the server MUST close the connection. The server then also checks if
this client definition allows this particular source IP address. If
the source IP address is not allowed, the server MUST close the
connection.
Where the server does not receive TLS-PSK from the client, it
proceeds with another authentication method such as client
certificates. Such requirements are discussed elsewhere, most
notably in [RFC6614] and [RFC7360].
Returning to the subject of IP address lookips, an implementation may
perform two independent IP address lookups. First, to check if the
connection allowed at all, and secod to check if the connection is
authorized for this particular client. One or both checks may be
used by a particular implementation. The two sets of IP addresses
can overlap, and implementations SHOULD support that capability.
Depending on the implementation, one or more clients may share a list
of allowed network ranges. Alternately, the allowed network ranges
for two clients can overlap only partially, or not at all. All of
these possibilities MUST be supported by the server implementation.
DeKok Expires 11 July 2024 [Page 13]
Internet-Draft RADIUS and TLS-PSK January 2024
6.2.2. PSK Authentication
Once the source IP has been verified to be allowed for this
particular client, the server authenticates the TLS connection via
the PSK taken from the client definition. If the PSK is verified,
the server then accepts the connection, and proceeds with RADIUS/TLS
as per [RFC6614].
If the PSK is not verified, then the server MUST close the
connection. While TLS provides for fallback to other authentication
methods such as client certificates, there is no reason for a client
to be configured simultaneously with multiple authentication methods.
A client MUST use only one authentication method for TLS. An
authentication method is either TLS-PSK, client certificates, or some
other method supported by TLS.
That is, client configuration is relatively simple: use a particular
set of credentials to authenticate to a particular server. While
clients may support multiple servers and fail-over or load-balancing,
that configuration is generally orthoganal to the choice of which
credentials to use.
6.2.3. Resumption
Implementations SHOULD support resumption. In many cases session
tickets can be authenticated solely by the server, and do not require
querying a database. The use of resumption can allow the system to
better scale to higher loads.
However, the above discussion of PSK identities is complicated by the
use of PSKs for resumption in TLS 1.3. A server which receives a PSK
identity via TLS typically cannot query the TLS layer to see if this
identity is for a resumed session, or is instead a static pre-
provisioned identity. This confusion complicates server
implementations.
One way for a server to tell the difference between the two kinds of
identies is via construction. Identities used for resumption can be
constructed via a fixed format, such as recommended by [RFC5077],
Section 4. A static pre-provisioned identity could be in format of
an NAI, as given in [RFC7542]. An implementation could therefore
examine the incoming identity, and determine from the identity alone
what kind of authentication was being performed.
An alternative way for a server to distinguish the two kinds of
identities is to maintain two tables. One table would contain static
identities, as the logical client table described above. Another
DeKok Expires 11 July 2024 [Page 14]
Internet-Draft RADIUS and TLS-PSK January 2024
table could be the table of identities handed out for resumption.
The server would then look up any PSK identity in one table, and if
not found, query the other one. An identity would be found in a
table, in which case it can be authenticated. Or, the identity would
not be found in either table, in which case it is unknown, and the
server MUST close the connection.
As suggested in [RFC8446], TLS-PSK peers MUST NOT store resumption
PSKs or tickets (and associated cached data) for longer than 604800
seconds (7 days) regardless of the PSK or ticket lifetime.
Systems supporting TLS-PSK and resumption MUST cache data during the
initial full handshake sufficient to allow authorization decisions to
be made during resumption. If cached data cannot be retrieved
securely, resumption MUST NOT be done. The cached data is typically
information such as the original PSK identity, along with any
policies associated with that identity.
Information from the original TLS exchange (e.g., the original PSK
identity) as well as related information (e.g., source IP addresses)
may change between the initial full handshake and resumption. This
change creates a "time-of-check time-of-use" (TOCTOU) security
vulnerability. A malicious or compromised client could supply one
set of data during the initial authentication, and a different set of
data during resumption, potentially allowing them to obtain access
that they should not have.
If any authorization or policy decisions were made with information
that has changed between the initial full handshake and resumption,
and if change may lead to a different decision, such decisions MUST
be reevaluated. It is RECOMMENDED that authorization and policy
decisions are reevaluated based on the information given in the
resumption. TLS-PSK servers MAY reject resumption where the
information supplied during resumption does not match the information
supplied during the original authentication. If a safe decision is
not possible, TLS-PSK servers SHOULD reject the resumption and
continue with a full handshake.
6.2.4. Interaction with other TLS authentication methods
When a server supports both TLS-PSK and client certificates, it MUST
be able to accept authenticated connections from clients which may
use either type of credentials, perhaps even from the same source IP
address and at the same time. That is, servers are required to both
authenticate the client, and also to filter clients by source IP
address. These checks both have to match in order for a client to be
accepted.
DeKok Expires 11 July 2024 [Page 15]
Internet-Draft RADIUS and TLS-PSK January 2024
7. Privacy Considerations
We make no changes over [RFC6614] and [RFC7360].
8. Security Considerations
The primary focus of this document is addressing security
considerations for RADIUS.
9. IANA Considerations
There are no IANA considerations in this document.
RFC Editor: This section may be removed before final publication.
10. Acknowledgments
Thanks to the many reviewers in the RADEXT working group for positive
feedback.
11. Changelog
* 00 - initial version
* 01 - update examples
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/rfc/rfc2119>.
[RFC2865] Rigney, C., Willens, S., Rubens, A., and W. Simpson,
"Remote Authentication Dial In User Service (RADIUS)",
RFC 2865, DOI 10.17487/RFC2865, June 2000,
<https://www.rfc-editor.org/rfc/rfc2865>.
[RFC4279] Eronen, P., Ed. and H. Tschofenig, Ed., "Pre-Shared Key
Ciphersuites for Transport Layer Security (TLS)",
RFC 4279, DOI 10.17487/RFC4279, December 2005,
<https://www.rfc-editor.org/rfc/rfc4279>.
DeKok Expires 11 July 2024 [Page 16]
Internet-Draft RADIUS and TLS-PSK January 2024
[RFC6614] Winter, S., McCauley, M., Venaas, S., and K. Wierenga,
"Transport Layer Security (TLS) Encryption for RADIUS",
RFC 6614, DOI 10.17487/RFC6614, May 2012,
<https://www.rfc-editor.org/rfc/rfc6614>.
[RFC7360] DeKok, A., "Datagram Transport Layer Security (DTLS) as a
Transport Layer for RADIUS", RFC 7360,
DOI 10.17487/RFC7360, September 2014,
<https://www.rfc-editor.org/rfc/rfc7360>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/rfc/rfc8174>.
[RFC9257] Housley, R., Hoyland, J., Sethi, M., and C. A. Wood,
"Guidance for External Pre-Shared Key (PSK) Usage in TLS",
RFC 9257, DOI 10.17487/RFC9257, July 2022,
<https://www.rfc-editor.org/rfc/rfc9257>.
[RFC9325] Sheffer, Y., Saint-Andre, P., and T. Fossati,
"Recommendations for Secure Use of Transport Layer
Security (TLS) and Datagram Transport Layer Security
(DTLS)", BCP 195, RFC 9325, DOI 10.17487/RFC9325, November
2022, <https://www.rfc-editor.org/rfc/rfc9325>.
12.2. Informative References
[RFC5077] Salowey, J., Zhou, H., Eronen, P., and H. Tschofenig,
"Transport Layer Security (TLS) Session Resumption without
Server-Side State", RFC 5077, DOI 10.17487/RFC5077,
January 2008, <https://www.rfc-editor.org/rfc/rfc5077>.
[RFC6613] DeKok, A., "RADIUS over TCP", RFC 6613,
DOI 10.17487/RFC6613, May 2012,
<https://www.rfc-editor.org/rfc/rfc6613>.
[RFC7542] DeKok, A., "The Network Access Identifier", RFC 7542,
DOI 10.17487/RFC7542, May 2015,
<https://www.rfc-editor.org/rfc/rfc7542>.
[RFC7585] Winter, S. and M. McCauley, "Dynamic Peer Discovery for
RADIUS/TLS and RADIUS/DTLS Based on the Network Access
Identifier (NAI)", RFC 7585, DOI 10.17487/RFC7585, October
2015, <https://www.rfc-editor.org/rfc/rfc7585>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/rfc/rfc8446>.
DeKok Expires 11 July 2024 [Page 17]
Internet-Draft RADIUS and TLS-PSK January 2024
[RFC8492] Harkins, D., Ed., "Secure Password Ciphersuites for
Transport Layer Security (TLS)", RFC 8492,
DOI 10.17487/RFC8492, February 2019,
<https://www.rfc-editor.org/rfc/rfc8492>.
[RFC8937] Cremers, C., Garratt, L., Smyshlyaev, S., Sullivan, N.,
and C. Wood, "Randomness Improvements for Security
Protocols", RFC 8937, DOI 10.17487/RFC8937, October 2020,
<https://www.rfc-editor.org/rfc/rfc8937>.
[RFC9258] Benjamin, D. and C. A. Wood, "Importing External Pre-
Shared Keys (PSKs) for TLS 1.3", RFC 9258,
DOI 10.17487/RFC9258, July 2022,
<https://www.rfc-editor.org/rfc/rfc9258>.
Author's Address
Alan DeKok
FreeRADIUS
Email: aland@freeradius.org
DeKok Expires 11 July 2024 [Page 18]