Internet Engineering Task Force (IETF)                         S. Venaas
Request for Comments: 6450                                 Cisco Systems
Category: Standards Track                                  December 2011
ISSN: 2070-1721


                        Multicast Ping Protocol

Abstract

   The Multicast Ping Protocol specified in this document allows for
   checking whether an endpoint can receive multicast -- both Source-
   Specific Multicast (SSM) and Any-Source Multicast (ASM).  It can also
   be used to obtain additional multicast-related information, such as
   multicast tree setup time.  This protocol is based on an
   implementation of tools called "ssmping" and "asmping".

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Further information on
   Internet Standards is available in Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6450.

Copyright Notice

   Copyright (c) 2011 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.






Venaas                       Standards Track                    [Page 1]

RFC 6450                 Multicast Ping Protocol           December 2011


Table of Contents

   1. Introduction ....................................................2
      1.1. Requirements Language ......................................2
   2. Architecture ....................................................3
   3. Protocol Specification ..........................................6
      3.1. Option Format ..............................................7
      3.2. Defined Options ............................................7
      3.3. Packet Format .............................................13
      3.4. Message Types and Options .................................13
      3.5. Rate Limiting .............................................15
           3.5.1. Message Rate Variables .............................16
   4. Client Behaviour ...............................................16
   5. Server Behaviour ...............................................18
   6. Recommendations for Implementers ...............................19
   7. IANA Considerations ............................................20
   8. Security Considerations ........................................21
   9. Acknowledgments ................................................22
   10. References ....................................................23
      10.1. Normative References .....................................23
      10.2. Informative References ...................................23

1.  Introduction

   The Multicast Ping Protocol specified in this document allows for
   checking multicast connectivity.  In addition to checking reception
   of multicast (SSM or ASM), the protocol can provide related
   information, such as multicast tree setup time, the number of hops
   the packets have traveled, and packet delay and loss.  This
   functionality resembles, in part, the ICMP Echo Request/Reply
   mechanism [RFC0792], but uses UDP [RFC0768] and requires that both a
   client and a server implement this protocol.  Intermediate routers
   are not required to support this protocol.  They forward protocol
   messages and data traffic as usual.

   This protocol is based on the current implementation of the ssmping
   and asmping tools [IMPL], which are widely used by the Internet
   community to conduct multicast connectivity tests.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].







Venaas                       Standards Track                    [Page 2]

RFC 6450                 Multicast Ping Protocol           December 2011


2.  Architecture

   Before describing the protocol in detail, we provide a brief overview
   of how the protocol may be used and what information it may provide.

   The protocol is used between clients and servers to check multicast
   connectivity.  Servers are multicast sources, and clients are
   multicast receivers.  A server may be configured with a set of ranges
   of multicast addresses that can be used for testing, or it may use
   some implementation defaults.  Depending on the server configuration
   or the implementation, it may control which clients (which unicast
   addresses) are allowed to use different group ranges, and also
   whether clients can select a group address, or if the group address
   is selected by the server.  Whether several clients are allowed to
   simultaneously use the same multicast address also depends on
   configuration and/or implementation.

   In addition to the above state, a server normally has runtime soft
   state.  The server must generally perform rate limiting to restrict
   the number of client requests it handles.  This rate limiting is
   per-client IP address.  This state need usually only be maintained
   for a few seconds, depending on the limit used.  If the server
   provides unique multicast addresses to clients, it must also have
   soft state for tracking which multicast addresses are used by which
   client IP address.  This state should expire if the server has not
   received requests within a few minutes.  The exact timeout should
   ideally be configurable to cope with different environments.  If a
   client is expected to perform multicast ping checks continuously for
   a long period of time, and to cope with requests not reaching the
   client for several minutes, then this timeout needs to be extended.
   In order to verify the client IP address, the server should perform a
   return routability check by giving the client a non-predictable
   session ID.  This would then also be part of the server soft state
   for that client.

   Before it can perform a multicast ping test, a client must know the
   unicast address of a server.  In addition, it may be configured with
   a multicast address or range to use.  In that case, the client will
   tell the server which group or range it wishes to use.  If not, the
   server is left to decide the group.  Normally, a client sends
   Default-Client-Request-Rate requests per second.  It may, however, be
   configured to use another rate.  See the definition of
   Default-Client-Request-Rate in Section 3.5.1.  Note that the value
   can be less than 1.







Venaas                       Standards Track                    [Page 3]

RFC 6450                 Multicast Ping Protocol           December 2011


   At runtime, a client generates a client ID that is unique for the
   ping test.  This ID is included in all messages sent by the client.
   Further, if not supplied with a specific group address, the client
   will receive from the server a group address that is used for the
   ping requests.  It may also receive a Session ID from the server.
   The client ID, group address, and Session ID (if received) will then
   be fixed for all ping requests in this session.  When a client
   receives replies from a server, it will verify the client ID in the
   reply, and ignore it if not matching what it used in the requests.
   For each reply, it may print or record information like round trip
   time, number of hops, etc.  The client may, once a ping session is
   ended, calculate and print or record statistics based on the entire
   ping session.

   The typical protocol usage is as follows:

      A server runs continuously to serve requests from clients.  A
      client has somehow learned the unicast address of the server and
      tests the multicast reception from the server.

      The client application will then send a unicast message to the
      server, asking for a group to use.  Optionally, a user may request
      a specific group or scope, in which case the client will ask for a
      group matching the user's request.  The server will respond with a
      group to use, or an error if no group is available.

      Next, for ASM, the client joins an ASM group G, while for SSM it
      joins a channel (S,G), where G is the multicast group address
      specified by the server, and S is the unicast address used to
      reach the server.

      After joining the group/channel, the client unicasts multicast
      ping requests to the server.  The requests are sent using UDP with
      the destination port set to the standardised multicast ping port
      (9903).  The requests are sent periodically to the server.  The
      rate is by default Default-Client-Request-Rate (Section 3.5.1)
      requests per second, but the client may be configured to use
      another rate.  These requests contain a sequence number and,
      typically, a timestamp.  The requests are echoed by the server,
      which may add a few options.

      For each request, the server sends two replies.  One reply is
      unicast to the source IP address and source UDP port of the
      requesting client.  The other reply is multicast to the requested
      multicast group G and the source UDP port of the requesting
      client.





Venaas                       Standards Track                    [Page 4]

RFC 6450                 Multicast Ping Protocol           December 2011


      Both replies are sent from the same port on which the request was
      received.  The server should specify the TTL (IPv4 time-to-live or
      IPv6 hop-count) used for both the unicast and multicast messages
      (TTL of at least 64 is recommended) by including a TTL option.
      This allows the client to compute the number of hops.  The client
      should leave the group/channel when it has finished its
      measurements.

   By use of this protocol, a client (or a user of the client) can
   obtain information about several multicast delivery characteristics.
   First, by receiving unicast replies, the client can verify that the
   server is receiving the unicast requests, and is operational and
   responding.  Hence, provided that the client receives unicast
   replies, a failure to receive multicast indicates either a multicast
   problem or a multicast administrative restriction.  If it does
   receive multicast, it knows not only that it can receive multicast
   traffic but that it may also estimate the amount of time it took to
   establish the multicast tree (at least if it is in the range of
   seconds), whether there are packet drops, and the length and
   variation of round trip times (RTTs).

   For unicast, the RTT is the time from when the unicast request is
   sent to the time when the reply is received.  The measured multicast
   RTT also references the client's unicast request.  By specifying the
   TTL of the replies when they are originated, the client can also
   determine the number of router hops it is from the source.  Since
   similar information is obtained in the unicast replies, the host may
   compare its multicast and unicast results and is able to check for
   differences, such as the number of hops, and RTT.

   The number of multicast hops and changes in the number of hops over
   time may reveal details about the multicast tree and multicast tree
   changes.  Provided that the server sends the unicast and multicast
   replies nearly simultaneously, the client may also be able to measure
   the difference in one-way delay for unicast and multicast on the path
   from server to client.

   Servers may optionally specify a timestamp.  This may be useful,
   since the unicast and multicast replies cannot be sent simultaneously
   (the delay is dependent on the host's operating system and load).











Venaas                       Standards Track                    [Page 5]

RFC 6450                 Multicast Ping Protocol           December 2011


3.  Protocol Specification

   There are four different message types:

   o  Echo Request and Echo Reply messages, which are used for the
      actual measurements.

   o  An Init message, which SHOULD be used to initialise a ping session
      and negotiate which group to use.

   o  A Server Response message, which is mainly used in response to the
      Init message.

   The messages MUST always be in network byte order.  UDP checksums
   MUST always be used.

   The messages share a common format: one octet specifying the message
   type, followed by a number of options in TLV (Type, Length, and
   Value) format.  This makes the protocol easily extendible.

   Message types in the range 0-253 are reserved and available for
   allocation in an IANA registry.  Message types 254 and 255 are freely
   available for experimental use.  See Section 7.

   The Init message generally contains some prefix options asking the
   server for a group from one of the specified prefixes.  The server
   responds with a Server Response message that contains the group
   address to use, or possibly prefix options describing what multicast
   groups the server may be able to provide.

   For an Echo Request, the client includes a number of options, and a
   server MAY simply echo the contents (only changing the message type)
   without inspecting the options if it does not support any options.
   This might be true for a simple Multicast Ping Protocol server, but
   it severely limits what information a client can obtain and hence
   makes the protocol less useful.  However, the server SHOULD add a TTL
   option (allowing the client to determine the number of router hops a
   reply has traversed), and there are other options that a server
   implementation MAY support; e.g., the client may ask for certain
   information or a specific behaviour from the server.  The Echo Reply
   messages (one unicast and one multicast) MUST first contain the exact
   options from the request (in the same order), and then, immediately
   following, any options appended by the server.  A server MUST NOT
   process unknown options, but they MUST still be included in the Echo
   Reply.  A client MUST ignore any unknown options.






Venaas                       Standards Track                    [Page 6]

RFC 6450                 Multicast Ping Protocol           December 2011


   The size of the protocol messages is generally smaller than the Path
   MTU, and fragmentation is not a concern.  There may, however, be
   cases where the Path MTU is really small, or where a client sends
   large requests in order to verify that it can receive fragmented
   multicast datagrams.  This document does not specify whether Path MTU
   Discovery should be performed, etc.  A possible extension could be an
   option where a client requests Path MTU Discovery and receives the
   current Path MTU from the server.

   This document defines a number of different options.  Some options do
   not require processing by servers and are simply returned unmodified
   in the reply.  There are, however, other client options that the
   server may care about, as well as server options that may be
   requested by a client.  Unless otherwise specified, an option MUST
   NOT be used multiple times in the same message.

3.1.  Option Format

   All options are TLVs formatted as below.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |             Type              |           Length              |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                             Value                             |
      |                               .                               |
      |                               .                               |
      |                               .                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type (2 octets) specifies the option.

   Length (2 octets) specifies the length of the value field.  Depending
   on the option type, it can be from 0 to 65535.

   Value must always be of the specified length.  See the respective
   option definitions for possible values.  If the length is 0, the
   value field is not included.

3.2.  Defined Options

   This document defines the following options: Version (0), Client ID
   (1), Sequence Number (2), Client Timestamp (3), Multicast Group (4),
   Option Request (5), Server Information (6), TTL (9), Multicast Prefix
   (10), Session ID (11), and Server Timestamp (12).  Option values 7
   and 8 are deprecated and must not be allocated by any future
   document.  The options are defined below.



Venaas                       Standards Track                    [Page 7]

RFC 6450                 Multicast Ping Protocol           December 2011


   Option types in the range 0-65531 are reserved and available for
   allocation in an IANA registry.  Option types in the range
   65532-65535 are not registered and are freely available for
   experimental use.  See Section 7.

      Version, type 0

         Length MUST be 1.  This option MUST always be included in all
         messages, and for the current specified protocol this value
         MUST be set to 2 (in decimal).  Note that there are
         implementations of older revisions of this protocol that only
         partly follow this specification.  They can be regarded as
         version 1 and do not use this option.  If a server receives a
         message with a version other than 2 (or missing), the server
         SHOULD (unless it supports the particular version) send a
         Server Response message back with version set to 2.  This tells
         the client that the server expects version 2 messages.  Client
         ID and Sequence Number options MUST be echoed if present, so
         that a client can be certain it is a response to one of its
         messages, and to exactly which message.  The server SHOULD NOT
         include any other options.  A client receiving a response with
         a version other than 2 MUST stop sending requests to the server
         (unless it supports the particular version).

      Client ID, type 1

         Length MUST be non-zero.  A client SHOULD always include this
         option in all messages (both Init and Echo Request).  The
         client may use any value it likes to detect whether a reply is
         a reply to its Init/Echo Request or not.  A server should treat
         this as opaque data, and MUST echo this option back in the
         reply if present (both Server Response and Echo Reply).  The
         value might be a pseudo-random byte string that is likely to be
         unique, possibly combined with the client IP address.
         Predictability is not a big concern here.  This is used by the
         client to ensure that server messages are in response to its
         requests.  In some cases, a client may receive multicast
         responses to queries from other clients.  It is left to the
         client implementer how to use this option.

      Sequence Number, type 2

         Length MUST be 4.  A client MUST always include this in Echo
         Request messages and MUST NOT include it in Init messages.  A
         server replying to an Echo Request message MUST copy it into
         the Echo Reply (or Server Response message on error).  The
         sequence number is a 32-bit integer.  Values typically start at
         1 and increase by one for each Echo Request in a sequence.



Venaas                       Standards Track                    [Page 8]

RFC 6450                 Multicast Ping Protocol           December 2011


      Client Timestamp, type 3

         Length MUST be 8.  A client SHOULD include this in Echo Request
         messages and MUST NOT include it in Init messages.  A server
         replying to an Echo Request message MUST copy it into the Echo
         Reply.  The timestamp specifies the time when the Echo Request
         message is sent.  The first 4 bytes specify the number of
         seconds since the Epoch (0000 UTC Jan 1, 1970).  The next
         4 bytes specify the number of microseconds since the second
         specified in the first 4 bytes.  This option would typically be
         used by a client to compute round trip times.

         Note that while this protocol uses the above 32-bit format, it
         would have been better to use another format, such as the one
         defined in NTPv4 [RFC5905].  This should be considered for
         future extensions of the protocol.

      Multicast Group, type 4

         Length MUST be greater than 2.  It MAY be used in Server
         Response messages to tell the client what group to use in
         subsequent Echo Request messages.  It MUST be used in Echo
         Request messages to tell the server what group address to
         respond to (this group would typically be previously obtained
         in a Server Response message).  It MUST be used in Echo Reply
         messages (copied from the Echo Request message).  It MUST NOT
         be used in Init messages.  The format of the option value is as
         below.

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |        Address Family         |  Multicast group address...   |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+  ....                         |

         The address family is a value 0-65535 as assigned by IANA for
         Internet address families [ADDRFAMILY].  This is followed by
         the group address.  Length of the option value will be 6 for
         IPv4, and 18 for IPv6.

      Option Request, type 5

         Length MUST be greater than 1.  This option MAY be used in
         client messages (Init and Echo Request messages).  A server
         MUST NOT send this option, except that if it is present in an
         Echo Request message, the server MUST echo it in replies (Echo
         Reply message) to the Echo Request.  This option contains a
         list of option types for options that the client is requesting



Venaas                       Standards Track                    [Page 9]

RFC 6450                 Multicast Ping Protocol           December 2011


         from the server.  Support for this option is OPTIONAL for both
         clients and servers.  The length of this option will be a
         non-zero even number, since it contains one or more option
         types that are two octets each.  The format of the option value
         is as below.

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |          Option Type          |          Option Type          |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                             .....                             |

         This option might be used by the client to ask the server to
         include options like Server Timestamp or Server Information.  A
         client MAY request Server Information in Init messages; it MUST
         NOT request it in other messages.  A client MAY request a
         Server Timestamp in Echo Request messages; it MUST NOT request
         it in other messages.  Subject to enforcing the above
         restrictions, a server supporting this option SHOULD include
         the requested options in responses (Echo Reply messages) to the
         Echo Request containing the Option Request option.  The server
         may, according to implementation or local configuration, not
         necessarily include all the requested options, or possibly
         none.  Any options included are appended to the echoed options,
         similar to other options included by the server.

      Server Information, type 6

         Length MUST be non-zero.  It MAY be used in Server Response
         messages and MUST NOT be used in other messages.  Support for
         this option is OPTIONAL.  A server supporting this option
         SHOULD add it in Server Response messages if and only if
         requested by the client.  The value is a UTF-8 [RFC3629] string
         that might contain vendor and version information for the
         server implementation.  It may also contain information on
         which options the server supports.  An interactive client MAY
         support this option, and SHOULD then allow a user to request
         this string and display it.  Although support for this is
         OPTIONAL, we say that a server SHOULD return it if requested,
         since this may be helpful to a user running the client.  It is,
         however, purely informational; it is not needed for the
         protocol to function.








Venaas                       Standards Track                   [Page 10]

RFC 6450                 Multicast Ping Protocol           December 2011


      Deprecated, type 7

         This option code value was used by implementations of version 1
         of this protocol, and is not used in this version.  Servers
         MUST treat it as an unknown option (not process it if received,
         but if received in an Echo Request message, it MUST be echoed
         in the Echo Reply message).

      Deprecated, type 8

         This option code value was used by implementations of version 1
         of this protocol, and is not used in this version.  Servers
         MUST treat it as an unknown option (not process it if received,
         but if received in an Echo Request message, it MUST be echoed
         in the Echo Reply message).

      TTL, type 9

         Length MUST be 1.  This option contains a single octet
         specifying the TTL of an Echo Reply message.  Every time a
         server sends a unicast or multicast Echo Reply message, it
         SHOULD include this option specifying the TTL.  This is used by
         clients to determine the number of hops the messages have
         traversed.  It MUST NOT be used in other messages.  A server
         SHOULD specify this option if it knows what the TTL of the Echo
         Reply will be.  In general, the server can specify a specific
         TTL to the host stack.  Note that the TTL is not necessarily
         the same for unicast and multicast.  Also note that this option
         SHOULD be included even when not requested by the client.  The
         protocol will work even if this option is not included, but it
         limits what information a client can obtain.

         If the server did not include this TTL option, there is no
         reliable way for the client to know the initial TTL of the Echo
         Reply, and therefore the client SHOULD NOT attempt to calculate
         the number of hops the message has traversed.

      Multicast Prefix, type 10

         Length MUST be greater than 2.  It MAY be used in Init messages
         to request a group within the prefix(es), and it MAY be used in
         Server Response messages to tell the client from what
         prefix(es) it may try to obtain a group.  It MUST NOT be used
         in Echo Request/Reply messages.  Note that this option MAY be
         included multiple times to specify multiple prefixes.






Venaas                       Standards Track                   [Page 11]

RFC 6450                 Multicast Ping Protocol           December 2011


        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |        Address Family         | Prefix Length |Partial address|
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+     ....      |

         The address family is a value 0-65535 as assigned by IANA for
         Internet address families [ADDRFAMILY].  This is followed by a
         prefix length (4-32 for IPv4, 8-128 for IPv6, or 0 for the
         special "wildcard" use discussed below), and finally a group
         address.  For any family, prefix length 0 means that any
         multicast address from that family is acceptable.  This is what
         we call "wildcard".  The group address need only contain enough
         octets to cover the prefix length bits (i.e., the group address
         would have to be 3 octets long if the prefix length is 17-24,
         and there need be no group address for the wildcard with prefix
         length 0).  Any bits past the prefix length MUST be ignored.
         For IPv4, the option value length will be 4-7, while for IPv6,
         it will be 4-19, and for the wildcard, it will be 3.

      Session ID, type 11

         Length MUST be 4 or larger.  A server SHOULD include this in
         Server Response messages.  If a client receives this option in
         a message, the client MUST echo the Session ID option in
         subsequent Echo Request messages, with the exact same value.
         The Session ID may help the server in keeping track of clients
         and possibly manage per-client state.  The value of a new
         Session ID SHOULD be a pseudo-random byte string that is hard
         to predict; see [RFC4086].  The string MUST be at least 4 bytes
         long.  The Session ID can be used to mitigate spoofing of the
         source address of Echo Request messages.  We say that this
         option SHOULD be used, because it is important for security
         reasons.  There may, however, be environments where this is not
         required.  See Section 8, "Security Considerations", for
         details.

      Server Timestamp, type 12

         Length MUST be 8 bytes.  A server supporting this option SHOULD
         include it in Echo Reply messages, if requested by the client.
         The timestamp specifies the time when the Echo Reply message is
         sent.  The first 4 bytes specify the number of seconds since
         the Epoch (0000 UTC Jan 1, 1970).  The next 4 bytes specify the
         number of microseconds since the second specified in the first
         4 bytes.  If this option is not included, the protocol will
         still work, but it makes it impossible for a client to compute
         one-way delay.



Venaas                       Standards Track                   [Page 12]

RFC 6450                 Multicast Ping Protocol           December 2011


         Note that while this protocol uses the above 32-bit format, it
         would have been better to use another format, such as the one
         defined in NTPv4 [RFC5905].  This should be considered for
         future extensions of the protocol.

3.3.  Packet Format

   The format of all messages is a one-octet message type, followed by a
   variable number of options.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |    Type       |          Options ...                          |
      +-+-+-+-+-+-+-+-+            .                                  |
      |                            .                                  |
      |                            .                                  |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-      .....

   There are four message types defined.  Type 81 (the character Q in
   ASCII) specifies an Echo Request (Query).  Type 65 (the character A
   in ASCII) specifies an Echo Reply (Answer).  Type 73 (the character I
   in ASCII) is an Init message.  Type 83 (the character S in ASCII) is
   a Server Response message.

   The options immediately follow the type octet and are not aligned in
   any way (no spacing or padding); i.e., options might start at any
   octet boundary.  The option format is specified above.

3.4.  Message Types and Options

   We will now describe each of the four message types and which options
   they may contain.

      Init, type 73

         This message is sent by a client to request information from a
         server.  It is mainly used for requesting a group address, but
         it may also be used to check which group prefixes the server
         may provide groups from, or other server information.  It MUST
         include a Version option, and SHOULD include a Client ID.  It
         MAY include Option Request and Multicast Prefix options.  This
         message is a request for a group address if and only if it
         contains Multicast Prefix options.  If multiple Prefix options
         are included, they should be in prioritised order.  That is,
         the server will consider the prefixes in the order they are
         specified, and if it finds a group for a prefix, it will only
         return that one group, not considering the remaining prefixes.



Venaas                       Standards Track                   [Page 13]

RFC 6450                 Multicast Ping Protocol           December 2011


      Server Response, type 83

         This message is sent by a server, either as a response to an
         Init, or in response to an Echo Request.  When responding to an
         Init, it may provide the client with a multicast group (if
         requested by the client), or it may provide other server
         information.  In response to an Echo Request, the message tells
         the client to stop sending Echo Request messages.  The Version
         option MUST always be included.  Client ID and Sequence Number
         options are echoed if present in the client message.  When
         providing a group to the client, it includes a Multicast Group
         option.  It SHOULD include Server Information and Prefix
         options if requested.  It SHOULD also include the Session ID
         option.

      Echo Request, type 81

         This message is sent by a client, asking the server to send
         unicast and multicast Echo Reply messages.  It MUST include
         Version, Sequence Number, and Multicast Group options.  If a
         Session ID was received in a Server Response message, then the
         Session ID MUST be included.  It SHOULD include Client ID and
         Client Timestamp options.  It MAY include an Option Request
         option.

      Echo Reply, type 65

         This message is sent by a server in response to an Echo Request
         message.  This message is always sent in pairs, one as unicast
         and one as multicast.  The contents of the messages are mostly
         the same.  The server always echoes all of the options (but
         never the Session ID) from the Echo Request.  Any options in
         the Echo Request that are unsupported by the server are also to
         be echoed.  The two Echo Reply messages SHOULD both always
         contain a TTL option (not necessarily equal).  When requested,
         both Echo Reply messages SHOULD also contain Server Timestamps
         (not necessarily equal).














Venaas                       Standards Track                   [Page 14]

RFC 6450                 Multicast Ping Protocol           December 2011


   The matrix below summarises what options can go in what messages.

          \  Message Type    |  Init  |  Server  |  Echo   |  Echo  |
   Option  \                 |        | Response | Request | Reply  |
   ----------------------   -+--------+----------+---------+--------+
   Version (0)               |  MUST  |   MUST   |  MUST   |  ECHO  |
   Client ID (1)             | SHOULD |   ECHO   | SHOULD  |  ECHO  |
   Sequence Number (2)       |  NOT   |   ECHO   |  MUST   |  ECHO  |
   Client Timestamp (3)      |  NOT   |   NOT    | SHOULD  |  ECHO  |
   Multicast Group (4)       |  NOT   |   MAY    |  MUST   |  ECHO  |
   Option Request (5)        |  MAY   |   NOT    |  MAY    |  ECHO  |
   Server Information (6)    |  NOT   |    RQ    |  NOT    |  NOT   |
   Deprecated (7)            |  NOT   |   NOT    |  NOT    |  ECHO  |
   Deprecated (8)            |  NOT   |   NOT    |  NOT    |  ECHO  |
   TTL (9)                   |  NOT   |   NOT    |  NOT    | SHOULD |
   Multicast Prefix (10)     |  MAY   |   MAY    |  NOT    |  NOT   |
   Session ID (11)           |  NOT   |  SHOULD  |  ECHO   |  NOT   |
   Server Timestamp (12)     |  NOT   |   NOT    |  NOT    |   RQ   |
   ----------------------   -+--------+----------+---------+--------+

   "NOT" means that the option MUST NOT be included.  "ECHO" for a
   server means that if the option is specified by the client, then the
   server MUST echo the option in the response, with the exact same
   option value.  ECHO for a client only applies to the Session ID
   option.  If it is present in the Server Response, then it MUST be
   present with the exact same option value in the following Echo
   Request messages.  "RQ" means that the server SHOULD include the
   option in the response, when requested by the client using the Option
   Request option.

3.5.  Rate Limiting

   Clients MUST by default send at most Default-Client-Request-Rate
   (Section 3.5.1) Echo Request messages per second.  Note that the
   value can be less than 1.  Servers MUST by default perform rate
   limiting, to guard against this protocol being used for denial-of-
   service (DoS) attacks.  A server MUST by default limit the number of
   clients that can be served at the same time, and for a given client,
   a server MUST also by default respond to, on average, at most
   Default-Server-Rate-Limit (see Section 3.5.1) Echo Request messages
   per second.  Note that the value can be less than 1.  Server
   implementations should provide configuration options allowing certain
   clients to perform more rapid rates of Echo Request messages.  If
   higher rates are allowed for specific client IP addresses, then Init
   messages and the Session ID option MUST be used to help mitigate
   spoofing.





Venaas                       Standards Track                   [Page 15]

RFC 6450                 Multicast Ping Protocol           December 2011


   Implementers of applications/tools using this protocol SHOULD
   consider the UDP guidelines [RFC5405], in particular if clients are
   to send, or servers are to accept, Echo Request messages at rates
   exceeding the defaults given in this document.  See Section 8,
   "Security Considerations", for additional discussion.

3.5.1.  Message Rate Variables

   There are two variables that control message rates.  They are defined
   as follows.

      Default-Client-Request-Rate

         This variable defines the default client echo request rate,
         specifying the number of requests per second.  Note that the
         value may be less than one.  For example, a value of 0.1 means
         one packet per 10 seconds.  The value 1 is RECOMMENDED, but the
         value might be too small or large, depending on the type of
         network in which the client is deployed.  The value 1 is chosen
         because it should be safe in most deployments, and it is
         similar to what is typically used for the common tool "ping"
         for ICMP Echo Request messages.

      Default-Server-Rate-Limit

         This variable defines the default per-client rate limit
         that a server uses for responding to Echo Request messages.
         The average rate of replies MUST NOT exceed
         Default-Server-Rate-Limit per second.  Note that the value may
         be less than one.  For example, a value of 0.1 means an average
         of one packet per 10 seconds.  The value 1 is RECOMMENDED, but
         the value might be too small or large, depending on the type of
         network in which the client is deployed.  The value 1 is chosen
         because it should be safe in most deployments.  This value
         SHOULD be high enough to accept the value chosen for the
         Default-Client-Request-Rate.

4.  Client Behaviour

   We will consider how a typical interactive client using the above
   protocol would behave.

   A client only requires a user to specify the unicast address of the
   server.  It can then send an Init message with a prefix option
   containing the desired address family and zero prefix length
   (wildcard entry).  The server can then decide which group, from the
   specified family, it should return.  A client may also allow the user
   to specify group address(es) or prefix(es) (for IPv6, the user may



Venaas                       Standards Track                   [Page 16]

RFC 6450                 Multicast Ping Protocol           December 2011


   only be required to specify a scope or a Rendezvous Point (RP)
   address, from which the client can construct the desired prefix,
   possibly embedded-RP).  From this, the client can specify one or more
   prefix options in an Init message to tell the server which address it
   would prefer.  If the user specifies a group address, that can be
   encoded as a prefix of maximal length (e.g., 32 for IPv4).  The
   prefix options are in prioritised order; i.e., the client should put
   the most preferred prefix first.

   If the client receives a Server Response message containing a group
   address, it can start sending Echo Request messages; see the next
   paragraph.  If there is no group address option, the client would
   typically exit with an error message.  The server may have included
   some prefix options in the Server Response.  The client may use this
   to provide the user some feedback on what prefixes or scopes are
   available.

   Assuming the client got a group address in a Server Response, it
   can start the multicast pings, after letting the user know which
   group is being used.  Normally, a client should send at most
   Default-Client-Request-Rate (Section 3.5.1) Echo Request messages per
   second.

   When sending the Echo Request messages, the client must always
   include the group option.  If the Server Response contained a Session
   ID option, then it must also include a Session ID option, with the
   exact same value, in the Echo Request messages.  If a client receives
   a Server Response message in response to an Echo Request (that is, a
   Server Response message containing a sequence number), this means
   there is an error, and it should stop sending Echo Request messages.
   This could happen after server restart.

   The client may allow the user to request server information.  If the
   user requests server information, the client can send an Init message
   with no prefix options, but with an Option Request option, requesting
   that the server return a Server Information option.  The server will
   return server information, if supported, and it may also return a
   list of prefixes it supports.  It will not, however, return a group
   address.  The client may also try to obtain only a list of prefixes
   by sending an Init message with no prefixes and not requesting any
   specific options.

   Although this technique is not recommended, a client may pick a
   multicast group and send Echo Request messages without first going
   through the Init - Server Response negotiation.  If this is supported






Venaas                       Standards Track                   [Page 17]

RFC 6450                 Multicast Ping Protocol           December 2011


   by the server and the server is okay with the group used, the server
   can then send Echo Reply messages as usual.  If the server is not
   okay with the group used, it will send a Server Response telling the
   client to stop.

5.  Server Behaviour

   We will consider how a typical server using the above protocol would
   behave, first looking at how to respond to Init messages.

   If the Init message contains prefix options, the server should look
   at them in order and see if it can assign a multicast address from
   the given prefix.  The server would be configured with a (possibly
   default) set of groups it can offer.  It may have a large pool and
   pick a group at random, or possibly choose a group based on hashing
   of the client's IP address or identifier, or simply use a fixed
   group.  A server could possibly decide whether to include site-scoped
   group ranges based on the client's IP address.  It is left to the
   server to decide whether it should allow the same address to be used
   simultaneously by multiple clients.

   If the server finds a suitable group address, it returns this address
   in a group option in a Server Response message.  The server should
   additionally include a Session ID.  This may help the server if it is
   to keep some state -- for instance, to make sure the client uses the
   group assigned to it.  A good Session ID would be a pseudo-random
   byte string that is hard to predict; see [RFC4086].  If the server
   cannot find a suitable group address, or if there were no prefixes in
   the Init message, it may send a Server Response message containing
   prefix options listing what prefixes may be available to the client.
   Finally, if the Init message requests the Server Information option,
   the server should include that option.

   When the server receives an Echo Request message, it must first check
   that the group address and Session ID (if provided) are valid.  If
   the server is satisfied, it will send a unicast Echo Reply message
   back to the client, and also a multicast Echo Reply message to the
   group address.  The Echo Reply messages contain the exact options
   (but no Session ID), and in the same order as in the Echo Request;
   after that, the server adds a TTL option and additional options if
   needed.  For example, it may add a timestamp if requested by the
   client.  If the server is not happy with the Echo Request (such as
   bad group address or Session ID, or request is too large), it may
   send a Server Response message asking the client to stop.  This
   Server Response must echo the sequence number from the Echo Request.






Venaas                       Standards Track                   [Page 18]

RFC 6450                 Multicast Ping Protocol           December 2011


   This Server Response may contain group prefixes from which a client
   can try to request a group address.  The unicast and multicast Echo
   Reply messages have identical UDP payload, apart from possibly TTL
   and timestamp option values.

   Note that the server may receive Echo Request messages with no prior
   Init message.  This may happen when the server restarts or if a
   client sends an Echo Request with no prior Init message.  The server
   may go ahead and respond if it is okay with the group and Session ID
   (if included) used.  If it is not okay with this information, the
   server sends back a Server Response.

6.  Recommendations for Implementers

   The protocol, as specified, is fairly flexible and leaves a lot of
   freedom for implementers.  In this section, we present some
   recommendations.

   Server administrators should be able to configure one group prefix or
   multiple group prefixes in a server implementation.  When deploying
   servers on the Internet and in other environments, the server
   administrator should be able to restrict the server to respond to
   only a few multicast groups that should not be currently used by
   multicast applications.  A server implementation should also provide
   flexibility for an administrator to apply various policies to provide
   one group prefix or multiple group prefixes to specific clients,
   e.g., site-scoped addresses for clients that are inside the site.

   As specified in Section 3.5, for a given client, a server must
   by default respond to at most an average rate of
   Default-Server-Rate-Limit Echo Request messages per second.  A leaky
   bucket algorithm is suggested, where the rate can be higher for a few
   seconds, but the average rate should by default be limited to
   Default-Server-Rate-Limit messages per client per second.  Server
   implementations should provide administrative control of which client
   IP addresses to serve, and may also allow certain clients to perform
   more rapid rates of Echo Request messages.

   If a server uses different policies for different IP addresses, it
   should require clients to send Init messages and return an
   unpredictable Session ID to help mitigate spoofing.  This is an
   absolute requirement if exceeding the default rate limit.  See the
   specification in Section 3.5.








Venaas                       Standards Track                   [Page 19]

RFC 6450                 Multicast Ping Protocol           December 2011


7.  IANA Considerations

   IANA has assigned UDP user port 9903 (multicast-ping) for use by this
   protocol.  IANA also provides registries for message and option
   types.

   IANA has created a message types registry.  Message types are in the
   range 0-255.  Message types 0-253 are registered following the
   procedures for Specification Required from RFC 5226 [RFC5226], while
   types 254 and 255 are for experimental use.  The registry includes
   the messages defined in Section 3.4.  A message specification MUST
   describe the behaviour with known option types as well as the default
   behaviour with unknown option types.

   IANA has created an option type registry.  Option types 0-65531 are
   registered following the procedures for Specification Required from
   RFC 5226 [RFC5226], while types 65532-65535 are for experimental use.
   The registry should include the options defined in Section 3.2.  An
   option specification must describe how the option may be used with
   the known message types.  This includes which message types the
   option may be used with.

   The initial registry definitions are as follows:

   Multicast Ping Protocol Parameters:

   Registry Name: Multicast Ping Protocol Message Types
   Reference: RFC 6450
   Registration Procedures: Specification Required

   Registry:
   Type         Name                                  Reference
   -----------  ------------------------------------  ----------
   65           Echo Reply                            RFC 6450
   73           Init                                  RFC 6450
   81           Echo Request                          RFC 6450
   83           Server Response                       RFC 6450
   254-255      Experimental













Venaas                       Standards Track                   [Page 20]

RFC 6450                 Multicast Ping Protocol           December 2011


   Registry Name: Multicast Ping Protocol Option Types
   Reference: RFC 6450
   Registration Procedures: Specification Required

   Registry:
   Type         Name                                  Reference
   -----------  ------------------------------------  ----------
   0            Version                               RFC 6450
   1            Client ID                             RFC 6450
   2            Sequence Number                       RFC 6450
   3            Client Timestamp                      RFC 6450
   4            Multicast Group                       RFC 6450
   5            Option Request                        RFC 6450
   6            Server Information                    RFC 6450
   7            Deprecated                            RFC 6450
   8            Deprecated                            RFC 6450
   9            TTL                                   RFC 6450
   10           Multicast Prefix                      RFC 6450
   11           Session ID                            RFC 6450
   12           Server Timestamp                      RFC 6450
   65532-65535  Experimental

8.  Security Considerations

   There are some security issues to consider.  One is that a host may
   send an Echo Request with an IP source address of another host, and
   make an arbitrary multicast ping server on the Internet send packets
   to this other host.  This behaviour is fairly harmless.  The worst
   case is if the host receiving the unicast Echo Reply messages also
   happens to be joined to the multicast group used.  This is less of a
   problem for SSM, where also the source address of the server must
   match the address joined.  In this case, there would be an
   amplification effect, where the host receives twice as many replies
   as there are requests sent.  See below for how spoofing can be
   mitigated.

   For ASM (Any-Source Multicast), a host could also make a multicast
   ping server send multicast packets to a group that is used for
   something else, possibly disturbing other uses of that group.
   However, server implementations should allow administrators to
   restrict which groups a server responds to.  The administrator should
   then try to configure a set of groups that are not used for other
   purposes.  Another concern is bandwidth.  To limit the bandwidth
   used, a server MUST by default limit the number of clients that can
   be served at the same time, and a server MUST also by default perform
   per-client rate limiting.





Venaas                       Standards Track                   [Page 21]

RFC 6450                 Multicast Ping Protocol           December 2011


   In order to help mitigate spoofing, a server SHOULD require that the
   client send an Init message, and return an unpredictable Session ID
   in the response.  The ID should be associated with the IP address and
   have a limited lifetime.  The server SHOULD then only respond to Echo
   Request messages that have a valid Session ID associated with the
   source IP address of the Echo Request.  Note, however, that a server
   is replying with a Server Response message if the Session ID is
   invalid.  This is used to tell the client that something is wrong and
   that it should stop sending requests, and start over if necessary.
   This means, however, that someone may spoof a client request, and
   have the server send a message back to the client address.  One
   solution here would be for the server to have a very low rate limit
   for the Server Response messages.

   Note that the use of a Session ID only to some degree helps mitigate
   spoofing.  An attacker that is on the path between a client and a
   server may eavesdrop the traffic, learn a valid Session ID, and
   generate Echo Request messages using this ID.  The server will
   respond as long as the Session ID remains valid.

   This protocol may be used to establish a covert channel between a
   multicast ping client and other hosts listening to a multicast group.
   A client can, for instance, send an Echo Request containing an
   undefined option with arbitrary data.  The server would echo this
   back in an Echo Reply that may reach other hosts listening to that
   group.  One solution that should be considered for future protocol
   versions is to reply with a hash of the data, rather than simply a
   copy of the same data.

9.  Acknowledgments

   The ssmping concept was proposed by Pavan Namburi, Kamil Sarac, and
   Kevin C. Almeroth in the paper "SSM-Ping: A Ping Utility for Source
   Specific Multicast" (2004) and also "MPing: A Ping Utility for IP
   Multicast" (Sarac and Almeroth, 2004).  Mickael Hoerdt contributed
   several ideas.  Alexander Gall, Nicholas Humfrey, Nick Lamb, and Dave
   Thaler have contributed in different ways to the implementation of
   the ssmping tools [IMPL].  Many people in communities like the
   Trans-European Research and Education Networking Association
   (TERENA), Internet2, and the M6Bone (IPv6 multicast network) have
   used early implementations of ssmping and provided feedback that
   influenced the current protocol.  Thanks to Kevin Almeroth, Tony
   Ballardie, Bill Cerveny, Toerless Eckert, Marshall Eubanks, Gorry
   Fairhurst, Alfred Hoenes, Liu Hui, Bharat Joshi, Olav Kvittem, Hugo
   Santos, Kamil Sarac, Pekka Savola, Trond Skjesol, and Cao Wei for
   reviewing and providing feedback on this document.  In particular,
   Hugo, Gorry, and Bharat provided lots of input on several revisions
   of the document.



Venaas                       Standards Track                   [Page 22]

RFC 6450                 Multicast Ping Protocol           December 2011


10.  References

10.1.  Normative References

   [ADDRFAMILY]
              IANA, "Address Family Numbers",
              <http://www.iana.org/assignments/address-family-numbers>.

   [RFC0768]  Postel, J., "User Datagram Protocol", STD 6, RFC 768,
              August 1980.

   [RFC0792]  Postel, J., "Internet Control Message Protocol", STD 5,
              RFC 792, September 1981.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3629]  Yergeau, F., "UTF-8, a transformation format of ISO
              10646", STD 63, RFC 3629, November 2003.

   [RFC4086]  Eastlake 3rd, D., Schiller, J., and S. Crocker,
              "Randomness Requirements for Security", BCP 106, RFC 4086,
              June 2005.

   [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 5226,
              May 2008.

10.2.  Informative References

   [IMPL]     Venaas, S., "ssmping implementation",
              <http://software.uninett.no/ssmping/>.

   [RFC5405]  Eggert, L. and G. Fairhurst, "Unicast UDP Usage Guidelines
              for Application Designers", BCP 145, RFC 5405,
              November 2008.

   [RFC5905]  Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch,
              "Network Time Protocol Version 4: Protocol and Algorithms
              Specification", RFC 5905, June 2010.











Venaas                       Standards Track                   [Page 23]

RFC 6450                 Multicast Ping Protocol           December 2011


Author's Address

   Stig Venaas
   Cisco Systems
   Tasman Drive
   San Jose, CA  95134
   USA

   EMail: stig@cisco.com










































Venaas                       Standards Track                   [Page 24]