Internet DRAFT - draft-vasseur-ccamp-brpc
draft-vasseur-ccamp-brpc
Networking Working Group JP. Vasseur (Editor)
Internet-Draft Cisco Systems, Inc
Expires: August 11, 2006 R. Zhang
BT Infonet
N. Bitar
Verizon
February 7, 2006
A Backward Recursive PCE-based Computation (BRPC) procedure to compute
shortest inter-domain Traffic Engineering Label Switched Path
draft-vasseur-ccamp-brpc-00.txt
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on August 11, 2006.
Copyright Notice
Copyright (C) The Internet Society (2006).
Abstract
This document specifies a Path Computation Element (PCE)-based
procedure to compute inter-domain Traffic Engineering (TE)
Multiprotocol Label Switched (MPLS) and Generalized MPLS (GMPLS)
Label Switched (LSP) constrained shortest paths. In this document a
Vasseur, et al. Expires August 11, 2006 [Page 1]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
domain is referred to as a collection of network elements within a
common sphere of address management or path computational
responsibility such as IGP areas and Autonomous Systems.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
Table of Contents
1. History . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
4. General assumptions . . . . . . . . . . . . . . . . . . . . . 4
5. BRPC Procedure . . . . . . . . . . . . . . . . . . . . . . . . 5
5.1. Next-hop PCE discovery . . . . . . . . . . . . . . . . . . 5
5.2. Elements of procedure . . . . . . . . . . . . . . . . . . 6
6. PCEP Protocol Extensions . . . . . . . . . . . . . . . . . . . 8
7. Meric normalization . . . . . . . . . . . . . . . . . . . . . 9
8. Diverse en-to-end path computation . . . . . . . . . . . . . . 10
9. Path optimality . . . . . . . . . . . . . . . . . . . . . . . 10
10. 10. Reoptimization of an inter-domain TE LSP . . . . . . . . . 10
11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 10
12. Security Considerations . . . . . . . . . . . . . . . . . . . 11
13. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 11
14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 11
14.1. Normative References . . . . . . . . . . . . . . . . . . . 11
14.2. Informative References . . . . . . . . . . . . . . . . . . 11
14.3. Informative References . . . . . . . . . . . . . . . . . . 11
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 13
Intellectual Property and Copyright Statements . . . . . . . . . . 14
Vasseur, et al. Expires August 11, 2006 [Page 2]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
1. History
The aim of this document is to specify a Backward Recursive PCE-based
Computation (BRPC) procedure to compute shortest constrained inter-
domain (G)MPLS TE LSP. Such procedure had been initially documented
in draft-vasseur-ccamp-inter-domain-path-comp (Scenario 2) and is now
moved to a separated ID in the light of the progress made by the PCE
Working Group. Note that the protocol extensions related to the PCEP
protocol (see [I-D.ietf-pce-pcep]) may be moved in a separate
document.
2. Terminology
ABR Routers: routers used to connect two IGP areas (areas in OSPF or
levels in IS-IS).
ASBR Routers: routers used to connect together ASes of a different or
the same Service Provider via one or more Inter-AS links.
Boundary LSR: a boundary LSR is either an ABR in the context of
inter- area TE or an ASBR in the context of inter-AS TE.
Inter-AS TE LSP: A TE LSP that crosses an AS boundary.
Inter-area TE LSP: A TE LSP that crosses an IGP area.
LSR: Label Switch Router.
LSP: Label Switched Path.
PCE: Path Computation Element: an entity (component, application or
network node) that is capable of computing a network path or route
based on a network graph and applying computational constraints.
TED: Traffic Engineering Database.
The notion of contiguous, stitched and nested TE LSPs is defined in
[I-D.ietf-ccamp-inter-domain-rsvp-te] and will not be repeated here.
3. Introduction
The requirements for inter-area and inter-AS MPLS Traffic Engineering
have been developed by the Traffic Engineering Working Group (TE WG)
and have been stated in [RFC4105] and [RFC4216] respectively.
The framework for inter-domain MPLS Traffic Engineering has been
Vasseur, et al. Expires August 11, 2006 [Page 3]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
provided in [I-D.ietf-ccamp-inter-domain-framework].
[I-D.ietf-ccamp-inter-domain-pd-path-comp] proposes a path
computation technique for computing inter-domain (G)MPLS TE LSP
whereby the path is computed on a per-domain basis by the entry
border node of each domain (each node in charge of computing a
section of an inter-domain TE LSP path is always along the path of
such TE LSP). Such path computation technique fulfills some of the
requirements stated in [RFC4105] and [RFC4216]but not all of them.
In particular, it cannot guarantee to find an optimal (shortest)
inter-domain constrained path. Furthermore, it cannot be efficiently
used to compute a set of inter-domain diversely routed TE LSP.
The aim of this document is to describe a PCE-based TE LSP
computation procedure to compute optimal inter-domain constrained
(G)MPLS TE LSPs. Although one model consists of making the boundary
routers act as PCE, the Backward Recursive PCE-based Computation
(BRPC) procedure is not limited to that model.
Qualifying a path as optimal requires some clarification. Indeed, a
globally optimal TE LSP placement usually refers to a set of TE LSPs
whose placements optimize the network resources with regards to a
specified objective function (i.e a placement that reduces the
maximum or average network load for instance). In this document, an
optimal inter-domain constrained TE LSP is defined as the shortest
path, satisfying the set of required constraints, that would be
obtained in the absence of multiple domains (in other words, in a
totally flat network between the source and destination of the TE
LSP). The mechanisms proposed in this document are also applicable
to (G)MPLS TE domains other than areas and ASs.
4. General assumptions
In the rest of this document, we make the following set of
assumptions common to inter-area and inter-AS TE:
- Each area or AS is assumed to be capable of doing Traffic
Engineering (i.e. running OSPF-TE or ISIS-TE and RSVP-TE).
- No topology or resource information is distributed between domains
(as mandated per [RFC4105] and [RFC4216]), which is critical to
preserve IGP/BGP scalability and confidentiality in the case of TE
LSPs spanning multiple domains.
- While certain constraints like bandwidth can be used across
different domains, certain other TE constraints like resource
affinity, color, metric, etc. as listed in [RFC2702] could be
Vasseur, et al. Expires August 11, 2006 [Page 4]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
translated at domain boundaries. If required, it is assumed that, at
the domain boundary LSRs, there will exist some sort of local mapping
based on offline policy agreement, in order to translate such
constraints across domain boundaries during the inter-PCE
communication process.
- The various ASBRs are BGP peers, without any IGP running on the
inter-ASBR links.
- Each AS can be made of several IGP areas. The path computation
procedure described in this document applies to the case of a single
AS made of multiple IGP areas, multiples ASs made of a single IGP
areas or any combination of the above. For the sake of simplicity,
each AS will be considered to be comprised of a single area in this
document. The case of an Inter-AS TE LSP spanning multiple ASs where
some of those ASs are themselves made of multiple IGP areas can be
easily derived from this case by applying the BRPC procedure
described in this document, recursively.
5. BRPC Procedure
The BRPC procedure is a Multi-PCE path computation technique as
described in [I-D.ietf-pce-architecture]. A possible model consists
of hosting the PCE function on boundary routers (e.g. ABR or ASBR)
but this is not mandated by the BRPC path computation procedure.
BRPC does not make any assumptions with regards to the nature of the
inter-domain TE LSP that could be contiguous, nested or stitched.
No assumption is made on the actual path computation algorithm in use
by the PCE (it can be any variant of CSPF, algorithm based on linear-
programming to solve multi-constraints optimization problems and so
on).
5.1. Next-hop PCE discovery
The BRPC path computation procedure applies to the computation of an
optimal constrained inter-domain TE LSP once the sequence of domains
to be traversed has been determined. In tree-based topologies, the
set of possible domains to be traversed is reduced to a single
element (generally the case of Inter-area MPLS TE). When such set
comprises more than one element (there exists more than one possible
set of domains to reach the destination), procedures can be defined
on the PCC to enforce the set of traversed domains. Alternatively,
such selection can be made on the hop-by-hop basis relying on PCE
discovery mechanism (e.g. using domain scope IGP advertisements as
specified in [I-D.ietf-pce-disco-proto-igp]).
Vasseur, et al. Expires August 11, 2006 [Page 5]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
5.2. Elements of procedure
Terminology
- PCE(i) is a PCE with the scope of domain(i).
- Boundary Router (BR): ABR or ASBR.
- Entry BR of domain(n): a BR connecting domain(n-1) to domain(n).
- Exit BR of domain(n): a BR connecting domain(n) to domain(n+1).
- In each domain i:
* a set of X-en(i) entry BRs noted BR-en(k,i) where BR-en(k,i) is the
kth entry BR of domain(i).
* a set of X-ex(i) exit BR noted BR-ex(k,i) where BR-ex(k,i) is the
kth exit BR of domain(i). Definition of VSPT(i)
A virtual shortest path tree VSPT(i) returned by PCE(i) to PCE(i-1)
has the following form:
Root (TE LSP destination)
/ I \
BR-en(1,i) BR-en(2,i) ... BR-en((j), i).
Where j<= [X-en(i)]
Each link of VSPT(i) represents the shortest path between the
destination and BR-en(j,i) that satisfies the set of required
constraints for the TE LSP (bandwidth, affinities, ...). These are
path segments to reach the destination from BR-en(j,i).
Note that just BR having connectivity with some BR of domain(i-1)
must be considered. Furthermore, some BRs may be excluded according
to policy constraints (either due to local policy or policies
signaled in the path computation request).
Step 1: the PCC needs to first determine the PCE capable of serving
its path computation request. The path computation request is then
relayed until reaching a PCE(n) such that the TE LSP destination
resides in the domain(n). At each step of the process, the next PCE
can either be statically configured or dynamically discovered via
IGP/BGP extensions. If multiple PCEs are discovered, the PCE may
Vasseur, et al. Expires August 11, 2006 [Page 6]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
select a subset of these PCEs based on some local policies/
heuristics. Note also that a sequence of PCEs might be enforced by
policy on the PCC and this constraint can be either carried in the
PCECP path computation request or applied to the computed VSPT.
Step 2: PCE(n) computes VSPT(n) made of the list of shortest
constrained path(s) between every BR-en(j,n) and the TE LSP
destination using a suitable path computation algorithm (e.g. CSPF).
Step 3: PCE(n) returns the VSPT(n) to PC(n-1).
- For i=n-1 to 2:
PCE(i) concatenates the ASi topology (using its TED) with the
received VSPT(i+1) and computes VSPT(i).
In the case of Inter-AS TE, this operation also includes the links
connecting ASBRs of ASi and ASi+1.
End
Each branch of the VSPT tree (path) may be returned in the form of an
explicit path (in which case all the hops along the path segment are
listed) or a loose path (in which case only the BR is specified) so
as to preserve confidentiality.
Note: in term of computation of an inter-AS TE LSP path, an
interesting optimization consists of allowing the ASBRs to flood the
TE information related to the inter-ASBR link(s) although no IGP TE
is enabled over those links (and so there is no IGP adjacency over
the inter-ASBR links). This of course implies for the inter-ASBR
links to be TE-enabled although no IGP is running on those links.
This allows the PCE of a domain to get entire TE visibility up to the
set of entry ASBRs in the downstream domain.
A PCE MAY decide to support local caching of path computation in
order to optimize the path computation process. The downside of path
caching is the potential increase of call set up failure. When
caching is in use, it must be flushed upon TE LSP set up failure
provided that the PCE is along the inter-area/AS TE LSP path. BRPC
guarantees to find the optimal (shortest) constrained inter-domain TE
LSP according to a set of defined domains to be traversed. Note that
other variants of the BRPC procedure relying on the same principles
are also possible. Note also that in case of ECMP paths, more than
one path could be returned to the requesting LSR. The BRPC procedure
may be used to compute path segments and could be used in conjunction
with other path computation techniques (such as the per-domain path
computation technique defined in [I-D.ietf-ccamp-inter-domain-pd-
Vasseur, et al. Expires August 11, 2006 [Page 7]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
path-comp]) to compute the end-to-end path. In this case end-to-end
path optimality can no longer be guaranteed.
6. PCEP Protocol Extensions
The BRPC path computation procedure requires the specification of a
new PCEP (see [I-D.ietf-pce-pcep]) object carried within a PCReq
message sent by a PCC to a PCE or by a PCE to another PCE so as to
request from a downstream PCE the set of shortest constrained path(s)
from the destination to a set of entry boundary routers. Indeed, the
END-POINTS object specified in PCEP makes the assumption that both
the source and the destination are known by the requester. Due to
potential lack of visibility of the entry boundary routers of the
downstream domain (e.g. Inter-AS MPLS TE case) the set of entry
boundary router in a downstream domain may not be known by the
requesting PCC: this requires to specify a new PCEP object named VSPT
for the purpose of the BRPC path computation procedure where the VSPT
object is used in a PCReq message so as to request from a downstream
PCE the VSPT from the destination to all entry BRs satisfy the
constraints.
Because path segment(s) computed by a downstream PCE in the context
of the BRPC procedure must be provided along with their respective
path cost(s), the C flag of the RP object carried within the PCReq
message MUST be set. It is the choice of the requester to
appropriately set the O bit of the RP object.
VSPT Object-Class is to be assigned by IANA (recommended value=14)
VSPT Object-Type is to be assigned by IANA (recommended value=1)
Vasseur, et al. Expires August 11, 2006 [Page 8]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
The format of the VSPT object body is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 2 - VSPT object body format (IPv4 Address)
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved | Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Destination IPv6 address (16 bytes) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3 - VSPT object body format (IPv6 Address)
The destination IP address of the VSPT object corresponds to the VSPT
root (TE LSP's destination) and is provided by the PCC originating
the path computation request.
No Flags are currently defined.
7. Meric normalization
In the case of inter-area TE, the same IGP/TE metric scheme is
usually adopted for all the IGP areas (e.g. based on the link-speed,
propagation delay or some other combination of link attributes).
Hence, the proposed set of mechanism always computes the shortest
path across multiple areas obeying the required set of constraints
with respect to a well-specified objective function. Conversely, in
the case of Inter-AS TE, in order for this path computation to be
meaningful, a metric normalization between ASs may be required. One
solution to avoid IGP metric modification would be for the SPs to
agree on a TE metric normalization scheme and use the TE metric for
TE LSP path computation (in that case, this must be requested in the
Path computation request) thanks to the COST object.
Vasseur, et al. Expires August 11, 2006 [Page 9]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
8. Diverse en-to-end path computation
The PCEP protocol allows an LSR to request the computation of a set
of diversely routed TE LSPs. In the context of the BRPC procedure, a
set of diversely routed TE LSP between two LSRs can be computed since
the paths segment(s) of the VSPT are simultaneously computed by a
given PCE. Such a PCE-based path computation method allows for the
computation of diverse paths under various objective functions (such
as minimizing the sum of the costs of the N diverse paths, etc) in a
very efficient manner, thus avoiding the well-known "trapping"
problem: Indeed, with a 2-step approach consisting of computing the
first path followed by the computation of the second path after
having removed the set of network elements traversed by the first
path (if that does not violate confidentiality preservation), one
cannot guarantee that a solution will be found even if such solution
exists. Furthermore, even if a solution is found, it may not be the
most optimal one with respect to objective function such as
minimizing the sum of the paths costs, bounding the path delays of
both paths and so on. Finally, it must be noted that such a 2-step
path computation approach is usually less efficient in term of
signalling delays since it requires two serialized TE LSP set up.
9. Path optimality
BRPC guarantees that the optimal (shortest) constrained inter-domain
path will always be found. It must be noted that although the BRPC
procedure applies to any type of inter-domain TE LSP (e.g.
contiguous, stitched or nested), the use of local reoptimization with
a stitched TE LSP may no longer guarantee to preserve the path
optimality of the end-to-end path should the BRPC procedure be used
in the first place.
10. 10. Reoptimization of an inter-domain TE LSP
The ability to reoptimize an existing inter-domain TE LSP path has
been explicitly listed as a requirement in [RFC4105] and [RFC4216].
In the case of a TE LSP reoptimization request, regular procedures
apply as defined in PCEP where the path in use (if available on the
head-end) is provided within the path computation request in order
for the PCEs involved in the reoptimization request to avoid double
bandwidth accounting.
11. IANA Considerations
A new PCEP object is defined in this document that has an Object-
Vasseur, et al. Expires August 11, 2006 [Page 10]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
Class and an Object-Type. The new Object-Class and Object-Type
should be assigned by IANA.
VSPT Object
The Object-Class of the VSPT object is to be assigned by IANA
(recommended value=14).
One Object-Type is defined for this object and should be assigned by
IANA with a recommended value of 1.
12. Security Considerations
The BRPC procedure does not introduce any additional security issues
beyond the ones related to inter-PCE communication.
13. Acknowledgements
The authors would like to thank Arthi Ayyangar and Adrian Farrel for
their useful comments.
14. References
14.1. Normative References
[I-D.ietf-pce-architecture]
Farrel, A., "A Path Computation Element (PCE) Based
Architecture", draft-ietf-pce-architecture-04 (work in
progress), January 2006.
[I-D.ietf-pce-pcep]
Vasseur, J., "Path Computation Element (PCE) communication
Protocol (PCEP) - Version 1 -", draft-ietf-pce-pcep-00
(work in progress), November 2005.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
14.2. Informative References
14.3. Informative References
[I-D.ietf-ccamp-inter-domain-framework]
Farrel, A., "A Framework for Inter-Domain MPLS Traffic
Engineering", draft-ietf-ccamp-inter-domain-framework-04
Vasseur, et al. Expires August 11, 2006 [Page 11]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
(work in progress), July 2005.
[I-D.ietf-ccamp-inter-domain-pd-path-comp]
Vasseur, J., "A Per-domain path computation method for
establishing Inter-domain Traffic Engineering (TE) Label
Switched Paths (LSPs)",
draft-ietf-ccamp-inter-domain-pd-path-comp-01 (work in
progress), October 2005.
[I-D.ietf-ccamp-inter-domain-rsvp-te]
Ayyangar, A. and J. Vasseur, "Inter domain GMPLS Traffic
Engineering - RSVP-TE extensions",
draft-ietf-ccamp-inter-domain-rsvp-te-02 (work in
progress), October 2005.
[I-D.ietf-pce-disco-proto-igp]
Roux, J., "IGP protocol extensions for Path Computation
Element (PCE) Discovery",
draft-ietf-pce-disco-proto-igp-00 (work in progress),
November 2005.
[RFC2702] Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J.
McManus, "Requirements for Traffic Engineering Over MPLS",
RFC 2702, September 1999.
[RFC4105] Le Roux, J., Vasseur, J., and J. Boyle, "Requirements for
Inter-Area MPLS Traffic Engineering", RFC 4105, June 2005.
[RFC4216] Zhang, R. and J. Vasseur, "MPLS Inter-Autonomous System
(AS) Traffic Engineering (TE) Requirements", RFC 4216,
November 2005.
Vasseur, et al. Expires August 11, 2006 [Page 12]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
Authors' Addresses
JP Vasseur
Cisco Systems, Inc
1414 Massachusetts Avenue
Boxborough, MA 01719
USA
Email: jpv@cisco.com
Raymond Zhang
BT Infonet
2160 E. Grand Ave.
El Segundo, CA 90025
USA
Email: raymond_zhang@bt.infonet.com
Nabil Bitar
Verizon
40 Sylvan Road
Waltham, MA 02145
USA
Email: nabil.bitar@verizon.com
Vasseur, et al. Expires August 11, 2006 [Page 13]
Internet-Draft draft-vasseur-ccamp-brpc-00.txt February 2006
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The Internet Society (2006). This document is subject
to the rights, licenses and restrictions contained in BCP 78, and
except as set forth therein, the authors retain all their rights.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Vasseur, et al. Expires August 11, 2006 [Page 14]