Internet DRAFT - draft-irtf-nwcrg-nwc-ccn-reqs
draft-irtf-nwcrg-nwc-ccn-reqs
NWCRG and ICNRG K. Matsuzono
Internet-Draft H. Asaeda
Intended status: Informational NICT
Expires: August 31, 2022 C. Westphal
Huawei
February 27, 2022
Network Coding for Content-Centric Networking / Named Data Networking:
Considerations and Challenges
draft-irtf-nwcrg-nwc-ccn-reqs-09
Abstract
This document describes the current research outcomes in Network
Coding (NC) for Content-Centric Networking (CCNx) / Named Data
Networking (NDN), and clarifies the technical considerations and
potential challenges for applying NC in CCNx/NDN. This document is
the product of the Coding for Efficient Network Communications
Research Group (NWCRG) and the Information-Centric Networking
Research Group (ICNRG).
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 31, 2022.
Copyright Notice
Copyright (c) 2022 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Matsuzono, et al. Expires August 31, 2022 [Page 1]
Internet-Draft NC for CCNx/NDN February 2022
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1. Definitions related to NC . . . . . . . . . . . . . . . . 4
2.2. Definitions related to CCNx/NDN . . . . . . . . . . . . . 6
3. CCNx/NDN Basics . . . . . . . . . . . . . . . . . . . . . . . 6
4. NC Basics . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Advantages of NC and CCNx/NDN . . . . . . . . . . . . . . . . 8
6. Technical Considerations . . . . . . . . . . . . . . . . . . 9
6.1. Content Naming . . . . . . . . . . . . . . . . . . . . . 9
6.1.1. Unique Naming for NC Packets . . . . . . . . . . . . 9
6.1.2. Non-Unique Naming for NC Packets . . . . . . . . . . 10
6.2. Transport . . . . . . . . . . . . . . . . . . . . . . . . 11
6.2.1. Scope of NC . . . . . . . . . . . . . . . . . . . . . 11
6.2.2. Consumer Operation . . . . . . . . . . . . . . . . . 11
6.2.3. Forwarder Operation . . . . . . . . . . . . . . . . . 12
6.2.4. Producer Operation . . . . . . . . . . . . . . . . . 13
6.2.5. Backward Compatibility . . . . . . . . . . . . . . . 14
6.3. In-network Caching . . . . . . . . . . . . . . . . . . . 14
6.4. Seamless Consumer Mobility . . . . . . . . . . . . . . . 15
7. Challenges . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1. Adoption of Convolutional Coding . . . . . . . . . . . . 15
7.2. Rate and Congestion Control . . . . . . . . . . . . . . . 16
7.3. Security . . . . . . . . . . . . . . . . . . . . . . . . 16
7.4. Routing Scalability . . . . . . . . . . . . . . . . . . . 17
8. Security Considerations . . . . . . . . . . . . . . . . . . . 17
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 18
10. Informative References . . . . . . . . . . . . . . . . . . . 19
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 22
1. Introduction
Information-Centric Networking (ICN) in general, and Content-Centric
Networking (CCNx) [16] or Named Data Networking (NDN) [19] in
particular, have emerged as a novel communication paradigm advocating
the retrieval of data based on their names. This paradigm pushes
content awareness into the network layer. It is expected to enable
consumers to obtain the content they desire in a straightforward and
efficient manner from the heterogenous networks they may be connected
to. The CCNx/NDN architecture has introduced innovative ideas and
has stimulated research in a variety of areas, such as in-network
Matsuzono, et al. Expires August 31, 2022 [Page 2]
Internet-Draft NC for CCNx/NDN February 2022
caching, name-based routing, multipath transport, and content
security. One key benefit of requesting content by name is that it
eliminates the requirement to establish a session between the client
and a specific server, and the content can thereby be retrieved from
multiple sources.
In parallel, there has been a growing interest in both academia and
industry for better understanding the fundamental aspects of Network
Coding (NC) toward enhancing key system performance metrics such as
data throughput, robustness and reduction in the required number of
transmissions through connected networks, and redundant transmission
on broadcast or point-to-multipoint connections. NC is a technique
that is typically used for encoding packets to recover from lost
source packets at the receiver, and for effectively obtaining the
desired information in a fully distributed manner. In addition, in
terms of security aspects, NC can be managed using a practical
security scheme that deals with pollution attacks [2], and can be
utilized for preventing eavesdroppers from obtaining meaningful
information [3] or protecting a wireless video stream while retaining
the NC benefits [4] [5].
From the perspective of the NC transport mechanism, NC can be divided
into two major categories: coherent NC, and non-coherent NC [38]
[39]. In coherent NC, the source and destination nodes know the
exact network topology and the coding operations available at
intermediate nodes. When multiple consumers are attempting to
receive the same content such as live video streaming, coherent NC
could enable optimal throughput by sending the content flow over the
constructed optimal multicast trees [32]. However, it requires a
fully adjustable and specific routing mechanism, and a large
computational capacity for central coordination. In the case of non-
coherent NC, which often uses Random Linear Coding (RLC), it is not
necessary to know the network topology nor the intermediate coding
operations [33]. As non-coherent NC works in a completely
independent and decentralized manner, this approach is more feasible
in terms of eliminating such a central coordination.
NC combines multiple packets together with parts of the same content,
and may do this at the source and/or at other nodes in the network.
Network coded packets are not associated with a specific server, as
they may have been combined within the network. As NC is focused on
what information should be encoded in a network packet instead of the
specific host at which it has been generated, it is in line with the
architecture of the CCNx/NDN core networking layer. NC allows for
recovery of missing packets by encoding the information across
several packets. ICN is synergistic with NC, as it allows for
caching of data packets throughout the network. In a typical network
that uses NC, the sender must transmit enough packets to retrieve the
Matsuzono, et al. Expires August 31, 2022 [Page 3]
Internet-Draft NC for CCNx/NDN February 2022
original data. ICN offers an opportunity to retrieve network coded
packets directly from caches in the network and this makes the
combination of ICN and NC particularly effective. In fact, NC has
already been implemented for information/content dissemination [6]
[7] [8]. Montpetit, et al., first suggested that NC techniques be
exploited to enhance key aspects of system performance in ICN [9].
Although CCNx/NDN excels to exploit the benefits of NC (as described
in Section 5), some technical considerations are needed to combine NC
and CCNx/NDN owing to the unique features of CCNx/NDN (as described
in Section 6).
In this document, we consider how NC can be applied to the CCNx/NDN
architecture and describe the technical considerations and potential
challenges for making CCNx/NDN-based communications better using the
NC technology. It should be noted that the presentation of specific
solutions (e.g., NC optimization methods) for enhancing CCNx/NDN
performance metrics by exploiting NC is outside the scope of this
document.
This document represents the collaborative work and consensus of the
Coding for Efficient Network Communications Research Group (NWCRG)
and the Information-Centric Networking Research Group (ICNRG). It is
not an IETF product and is not a standard.
2. Terminology
2.1. Definitions related to NC
This section provides the terms related to NC used in this document,
which are defined in RFC8406 [21] produced by NWCRG.
o Source Packet: A packet originating from the source that
contributes to one or more source symbols. The source symbol is a
unit of data originating from the source that is used as input to
encoding operations. For instance, a real-time transport protocol
(RTP) packet as a whole can constitute a source symbol. In other
situations (e.g., to address variable size packets), a single RTP
packet may contribute to various source symbols.
o Repair Packet: A packet containing one or more coded symbols (also
called repair symbol). Coded symbol or repair symbol is a unit of
data that is the result of a coding operation, applied either to
source symbols or (in case of re-coding) source and/or coded
symbols. When there is a single repair symbol per repair packet,
a repair symbol corresponds to a repair packet.
o Encoding versus Re-coding versus Decoding: Encoding is an
operation that takes source symbols as input and produces encoding
Matsuzono, et al. Expires August 31, 2022 [Page 4]
Internet-Draft NC for CCNx/NDN February 2022
symbols (source or coded symbols) as output. Re-coding is an
operation that takes encoding symbols as input and produces
encoding symbols as output. Decoding is an operation takes
encoding symbols as input and produces source symbols as output.
The terms regarding coding types are defined as follows:
o Random Linear Coding (RLC): A particular form of linear coding
using a set of random coding coefficients. Linear coding performs
linear combination of a set of input symbols (i.e., source and/or
coded symbols) using a given set of coefficients and results in a
repair symbol.
o Block Coding: A coding technique wherein the input flow(s) must be
first segmented into a sequence of blocks; encoding and decoding
are performed independently on a per-block basis.
o Sliding Window Coding or Convolutional Coding: A general class of
coding techniques that rely on a sliding encoding window.
Encoding window is a set of source (and coded in the case of re-
coding) symbols used as input to the coding operations. The set
of symbols change over time, as the encoding window slides over
the input flow(s). This is an alternative solution to block
coding.
o Fixed or Elastic Sliding Window Coding: A coding technique that
generates coded symbol(s) on the fly, from the set of source
symbols present in the sliding encoding window at that time,
usually by using linear coding. The sliding window may be either
of fixed size or of variable size over the time (also known as
"Elastic Sliding Window"). For instance, the size may depend on
acknowledgments sent by the receiver(s) for a particular source
symbol or source packet (received, decoded, or decodable).
The terms regarding low-level coding aspects are defined as follows:
o Rank of the Linear System or Degrees of Freedom: At a receiver,
the number of linearly independent equations of the linear system.
It is also known as "Degrees of Freedom". The system may be of
"full rank," wherein decoding is possible, or "partial rank",
wherein only partial decoding is possible.
o Generation, or Block: With block codes, the set of source symbols
of the input flow(s) that are logically grouped into a block,
before doing encoding.
o Generation Size, or Block Size: With block codes, the number of
source symbols belonging to a block. It is equivalent to the
Matsuzono, et al. Expires August 31, 2022 [Page 5]
Internet-Draft NC for CCNx/NDN February 2022
number of source packets when there is a single source symbol per
source packet.
o Coding Coefficient: With linear coding, this is a coefficient in a
certain finite field. This coefficient may be chosen in different
ways: for instance, randomly, in a predefined table, or using a
predefined algorithm plus a seed.
o Coding Vector: A set of coding coefficients used to generate a
certain coded symbol through linear coding.
o Finite Field: Finite fields, used in linear codes, have the
desired property of having all elements (except zero) invertible
for + and * and no operation over any elements can result in an
overflow or underflow. Examples of finite fields are prime fields
{0..p^m-1}, where p is prime. Most used fields use p=2 and are
called binary extension fields {0..2^m-1}, where m often equals 1,
4 or 8 for practical reasons.
2.2. Definitions related to CCNx/NDN
The terminology regarding CCNx/NDN used in this document is defined
in RFC8793 [17] produced by ICNRG. They are consistent with the
relevant documents ([1] [18]).
3. CCNx/NDN Basics
We briefly explain the key concepts of CCNx/NDN. In a CCNx/NDN
network, there are two types of packets at the network level:
interest and data packet (defined in Section 3.4 of [17]). The term
of content object, which means a unit of content data, is an alias to
data packet [17]. The ICN consumer (defined in Section 3.2 of [17])
requests a content object by sending an interest that carries the
name of the data.
Once an ICN forwarder (defined in Section 3.2 of [17]) receives an
interest, it performs a series of lookups: first it checks if it has
a copy of the requested content object available in the cache storage
called Content Store (CS) (defined in Section 3.3 of [17]). If it
does, it returns the data, and the transaction is considered to have
been successfully completed.
If it does not have a copy of the requested content object in the CS,
it performs a lookup of the Pending Interest Table (PIT) (defined in
Section 3.3 of [17]) to check if there is already an outgoing
interest for the same content object. If there is no such interest,
then it creates an entry in the PIT that lists the name included in
the interest, and the interfaces from which it received the interest.
Matsuzono, et al. Expires August 31, 2022 [Page 6]
Internet-Draft NC for CCNx/NDN February 2022
This is later used to send the content object back, as interest
packets do not carry a source field that identifies the consumer. If
there is already a PIT entry for this name, it is updated with the
incoming interface of this new interest, and the interest is
discarded.
After the PIT lookup, the interest undergoes a Forwarding Information
Base (FIB) (defined in Section 3.3 of [17]) lookup for selecting an
outgoing interface. The FIB lists name prefixes and their
corresponding forwarding interfaces in order to send the interest
towards a forwarder that possesses a copy of the requested data.
Once a copy of the data is retrieved, it is sent back to the
consumer(s) using the trail of PIT entries; forwarders remove the PIT
state every time that an interest is satisfied, and may store the
data in their CS.
Data packets carry some information for verifying data integrity and
origin authentication, and in particular, that the data is indeed
that which corresponds to the name [24]. This is necessary because
authentication of the object is crucial in CCNx/NDN. However, this
step is optional at forwarders in order to speed up the processing.
The key aspect of CCNx/NDN is that the consumer of the content does
not establish a session with a specific server. Indeed, the
forwarder or producer (defined in Section 3.2 of [17]) that returns
the content object is not aware of the network location of the
consumer and the consumer is not aware of the network location of the
node that provides the content. This, in theory, allows the
interests to follow different paths within a network or even to be
sent over completely different networks.
4. NC Basics
While the forwarding node simply relays received data packets in
conventional IP communication networks, NC allows the node to combine
some data packets that are already received into one or several
output packets to be sent. In this section, we simply describe the
basic operations of NC. Herein, we focus on RLC in a block coding
manner that is well known as a major coding technique.
For simplicity, let us consider an example case of end-to-end coding
wherein a producer and consumer respectively perform encoding and
decoding for a content object. This end-to-end coding is regarded as
a special case of NC. The producer splits the content into several
blocks called generations. Encoding and decoding are performed
independently on a per-block (per-generation) basis. Let us assume
that each generation consists of K original source packets of the
Matsuzono, et al. Expires August 31, 2022 [Page 7]
Internet-Draft NC for CCNx/NDN February 2022
same size. When the packets do not have the same size, zero padding
is added. In order to generate one repair packet within a certain
generation, the producer linearly combines K of the original source
packets, where additions and multiplications are performed using a
coding vector consisting of K coding coefficients that are randomly
selected in a certain finite field. The producer may respond to
interests to send the corresponding source packets and repair packets
in the content flow (called systematic coding), where the repair
packets are typically used for recovering lost source packets.
Repair packets can also be used for performing encoding. If the
forwarding nodes know each coding vector and generation identifier
(hereinafter referred to as generation ID) of the received repair
packets, they may perform an encoding operation (called re-coding),
which is the most distinctie feature of NC compared to other coding
techniques.
At the consumer, decoding is performed by solving a set of linear
equations that are represented by the coding vectors of the received
source and repair packets (possibly only repair packets) within a
certain generation. In order to obtain all the source packets, the
consumer requires K linearly independent equations. In other words,
the consumer must receive at least K linearly independent data
packets (called innovative packets). As receiving a linearly
dependent data packet is not useful for decoding, re-coding should
generate and provide innovative packets. One of major benefits of
RLC is that even for a small-sized finite field (e.g., q=2^8), the
probability of generating linearly dependent packets is negligible
[32].
5. Advantages of NC and CCNx/NDN
Combining NC and CCNx/NDN can contribute to effective large-scale
content/information dissemination. They individually provide similar
benefits such as throughput/capacity gain and robustness enhancement.
The difference between their approaches is that, the former considers
content flow as algebraic information that is to be combined [20],
while the latter focuses on the content/information itself at the
networking layer. Because these approaches are complementary and
their combination would be advantageous, it is natural to combine
them.
The name-based communication in CCNx/NDN enables consumers to obtain
requested content objects without establishing and maintaining end-
to-end communication channels between nodes. This feature
facilitates the exploitation of the in-network cache and multipath/
multisource retrieval and also supports consumer mobility without the
need for updating the location information/identifier during handover
Matsuzono, et al. Expires August 31, 2022 [Page 8]
Internet-Draft NC for CCNx/NDN February 2022
[16]. Furthermore, the name-based communication intrinsically
supports multicast communication because identical interests are
aggregated at the forwarders.
NC can enable the CCNx/NDN transport system to effectively distribute
and cache the data associated with multipath data retrieval [9].
Exploiting multipath data retrieval and in-network caching with NC
contributes to not only improving the cache hit rate but also
expanding the anonymity set of each consumer (the set of potential
routers that can serve a given consumer) [30]. The expansion makes
it difficult for adversaries to infer the content consumed by others,
and thus contributes to improving cache privacy. Others also have
introduced some use cases of the application of NC in CCNx/NDN, such
as the cases of content dissemination with in-network caching [10]
[13] [14], seamless consumer mobility [11] [36], and low-latency low-
loss video streaming [15]. In this context, it is well worth
considering NC integration in CCNx/NDN.
6. Technical Considerations
This section presents the considerations for CCNx/NDN with NC in
terms of network architecture and protocol. This document focuses on
NC when employed in a block coding manner.
6.1. Content Naming
Naming content objects is as important for CCNx/NDN as naming hosts
is in the current-day Internet [24]. In this section, two possible
naming schemes are presented.
6.1.1. Unique Naming for NC Packets
Each source and repair packet (hereinafter referred to as NC packet)
may have a unique name as each original content object has in CCNx/
NDN, as PIT and CS operations typically require a unique name for
identifying the NC packet. As a method of naming an NC packet that
takes into account the feature of block coding, the coding vector and
the generation ID can be used as a part of the content object name.
As in [10], when the generation ID is "g-id", generation size is 4,
and coding vector is (1,0,0,0), the name could be /CCNx.com/video-A/
g-id/1000. Some other identifiers and/or parameters related to the
encoding scheme can also be used as name components. For instance,
the encoding ID specifying the coding scheme may be used with "enc-
id" such as /CCNx.com/video-A/enc-id/g-id/1000, as defined in the FEC
Framework (FECFRAME) [26]. This naming scheme is simple and can
support the delivery of NC packets with exactly the same operations
in the PIT/CS as those for the content objects.
Matsuzono, et al. Expires August 31, 2022 [Page 9]
Internet-Draft NC for CCNx/NDN February 2022
If a content-naming schema such as the one presented above is used,
an interest requesting an NC packet may have the full name including
a generation ID and coding vector (/CCNx.com/video-A/g-id/1000) or
only the name prefix including only a generation ID (/CCNx.com/video-
A/g-id). In the former case, exact name matching to the PIT is
simply performed at data forwarders (as in CCNx/NDN). The consumer
is able to specify and retrieve an innovative packet necessary for
the consumer to decode successfully. This could shift the generation
of the coding vector from the data forwarder onto the consumer.
In the latter case, partial name matching is required at the data
forwarders. As the interest with only the prefix name matches any NC
packet with the same prefix, the consumer could immediately obtain an
NC packet from a nearby CS (in-network cache) without knowing the
coding vectors of the cached NC packets in advance. In the case
wherein NC packets in transit are modified by in-network re-coding
performed at forwarders, the consumer could also receive the modified
NC packets. However, in contrast to the former case, the consumer
may fail to obtain sufficient degrees of freedom (see Section 6.2.3).
To address this issue, a new TLV type in an interest message may be
required for specifying further coding information in order to limit
the NC packets to be received. For instance, this is enabled by
specifying the coding vectors of innovative packets for the consumer
(also called decoding matrix) as in [9]. This extension may incur an
interest packet of significantly increased size, and it may thus be
useful to use compression techniques for coding vectors [27] [28].
Without such coding information provided by the interest, the
forwarder would be required to maintain some records regarding the
interest packets that were satisfied previously (See Section 6.2.3).
6.1.2. Non-Unique Naming for NC Packets
An NC packet may have a name that indicates that it is an NC packet,
and move the coding information into a metadata field in the payload
(i.e., the name includes the data type, source or repair packet).
This would not be beneficial for applications or services that may
not need to understand the packet payload. Owing to the possibility
that multiple NC packets may have the same name, some mechanism is
required for the consumer to obtain innovative packets. As described
in Section 6.3, a mechanism for managing the multiple innovative
packets in the CS would also be required. In addition, extra
computational overhead would be incurred when the payload is being
encrypted.
Matsuzono, et al. Expires August 31, 2022 [Page 10]
Internet-Draft NC for CCNx/NDN February 2022
6.2. Transport
The pull-based request-response feature of CCNx/NDN is a fundamental
principle of its transport layer; one interest retrieves at most one
data packet. This means that a forwarder or producer cannot inject
unrequested data packets on its own initiative. It is believed that
it is important that this rule not be violated, as 1) it would open
denial-of-service (DoS) attacks, 2) it invalidates existing
congestion control approaches following this rule, and 3) it would
reduce the efficiency of existing consumer mobility approaches.
Thus, the following basic operation should be considered for applying
NC to CCNx/NDN. Nevertheless, such security considerations must be
addressed if this rule were to be violated.
6.2.1. Scope of NC
An open question is whether data forwarder can perform in-network re-
coding with data packets that are being received in transit, or if
only the data that matches an interest can be subject to NC
operations. In the latter case, encoding or re-coding is performed
to generate the NC packet at any forwarder that is able to respond to
the interest. This could occur when each NC packet has a unique name
and interest has the full name. On the other hand, if interest has a
partial name without any coding vector information or multiple NC
packets have the same name, the former case may occur; re-coding
occurs anywhere in the network where it is possible to modify the
received NC packet and forward it. As CCNx/NDN comprises mechanisms
for ensuring the integrity of the data during transfer, in-network
re-coding introduces complexities in the network that needs
consideration for the integrity mechanisms to still work. Similarly,
in-network caching of NC packets at forwarders may be valuable;
however, the forwarders would require some mechanisms to validate the
NC packets (see Section 8).
6.2.2. Consumer Operation
To obtain NC benefits (possibly associated with in-network caching),
the consumer is required to issue interests that direct the forwarder
(or producer) to respond with innovative packets if available. In
the case where each NC packet may have a unique name (as described in
Section 6.1), by issuing an interest specifying a unique name with
g-id and the coding vector for an NC packet, the consumer could
appropriately receive an innovative packet if it is available at some
forwarders.
In order to specify the exact name of the NC packet to be retrieved,
the consumer is required to know the valid naming scheme. From a
practical viewpoint, it is desirable for the consumer application to
Matsuzono, et al. Expires August 31, 2022 [Page 11]
Internet-Draft NC for CCNx/NDN February 2022
automatically construct the right name components without depending
on any application specifications. To this end, the consumer
application may retrieve and refer to a manifest [1] that enumerates
the content objects including NC packets, or may use some coding
scheme specifier as a name component to construct the name components
of interests to request innovative packets.
Conversely, the consumer without decoding capability (e.g., specific
sensor node) may want to receive only the source packets. As
described in Section 6.1, because the NC packet can have a name that
is explicitly different from source packets, issuing interests for
retrieving source packets is possible.
6.2.3. Forwarder Operation
If the forwarder constantly responds to the incoming interests by
returning non-innovative packets, the consumer(s) cannot decode and
obtain the source packets. This issue could happen when 1) incoming
interests for NC packets do not specify some coding parameters such
as the coding vectors to be used, and 2) the forwarder does not have
a sufficient number of linearly independent NC packets (possibly in
the CS) to use for re-coding. In this case, the forwarder is
required to determine whether or not it can generate innovative
packets to be forwarded to the interface(s) at which the interests
arrived. An approach to deal with this issue is that the forwarder
maintains a tally of the interests for a specific name, generation ID
and the incoming interface(s), in order to record how many degrees of
freedom have already been provided [10]. As such a scheme requires
state management (and potentially timers) in forwarders, scalability
and practicality must be considered. In addition, some transport
mechanism for in-network loss detection and recovery [15] [36] at
forwarder as well as a consumer-driven mechanism could be
indispensable for enabling fast loss recovery and realising NC gains.
If a forwarder cannot either return a matching innovative packet from
its local content store, nor produce on-the-fly a recoded packet that
is innovative, it is important that the forwarder not simply return a
non-innovative packet but instead do a forwarding lookup in its FIB
and forward the interest toward the producer or upstream forwarder
that can provide an innovative packet. In this context, to retrieve
innovative packet effectively and quickly, an appropriate setting of
the FIB and efficient interest forwarding strategies should also be
considered.
In another possible case, when receiving interests only for source
packets, the forwarder may attempt to decode and obtain all the
source packets and store them (if the full cache capacity are
available), thus enabling a faster response to subsequent interests.
As re-coding or decoding results in an extra computational overhead,
Matsuzono, et al. Expires August 31, 2022 [Page 12]
Internet-Draft NC for CCNx/NDN February 2022
the forwarder is required to determine how to respond to received
interests according to the use case (e.g., a delay-sensitive or
delay-tolerant application) and the forwarder situation, such as
available cache space and computational capability.
6.2.4. Producer Operation
Before performing NC for specified content in CCNx/NDN, the producer
is responsible for splitting the overall content into small content
objects to avoid packet fragmentation that could cause unnecessary
packet processing and degraded throughput. The size of the content
objects should be within the allowable packet size in order to avoid
packet fragmentation in CCNx/NDN network. The producer performs the
encoding operation for a set of the small content objects, and the
naming process for the NC packets.
If the producer takes the lead in determining what coding vectors to
use in generating the NC packets, there are three general strategies
for naming and producing the NC packets:
1. consumers themselves understand in detail the naming conventions
used for NC packets and thereby can send the corresponding
interests toward the producer to obtain NC packets whose coding
parameters have already been determined by the producer.
2. the producer determines the coding vectors and generates the NC
packets after receiving interests specifying the packets the
consumer wished to receive.
3. The naming scheme for specifying the coding vectors and
corresponding NC packets is explicitly represented via a
"Manifest" (e.g., FLIC [23]) that can be obtained by the consumer
and used to select among the available coding vectors and their
corresponding packets, and thereby send the corresponding
interests.
In the first case, although the consumers cannot flexibly specify a
coding vector for generating the NC packet to obtain, the latency for
obtaining the NC packet is less than in the latter two cases. For
the second case, there is a latency penalty for the additional NC
operations performed after receiving the interests. For the third
case, the NC packets to be included in the manifest must be pre-
computed by the producer (since the manifest references NC packets by
their hashes, not their names), but the producer can select which to
include the manifest, and produce multiple manifests either in
advance or on demand with different coding tradeoffs if so desired.
Matsuzono, et al. Expires August 31, 2022 [Page 13]
Internet-Draft NC for CCNx/NDN February 2022
A common benefit the first two approaches to end-to-end coding is
that if the producer adds a signature on the NC packets, data
validation becomes possible throughout (as is the case with CCNx/NDN
operation in the absence of NC). The third approach of using a
manifest trades off the additional latency incurred by the need to
fetch the manifest against the efficiency of needing a signature only
on the manifest and not on each individual NC packet.
6.2.5. Backward Compatibility
NC operations should be applied in addition to the regular ICN
behavior, and should function alongside regular ICN operations.
Hence, nodes which do not support NC should still be able to properly
handle packets, not only in being able to forward the NC packets, but
also to cache these packets. An NC framework should be compatible
with a regular framework in order to facilitate backward
compatibility and smooth migration from one framework to the other.
6.3. In-network Caching
Caching is a useful technique used for improving throughput and
latency in various applications. In-network caching in CCNx/NDN
essentially provides support at network level and is highly
beneficial owing to the involved exploitation of NC for enabling
effective multicast transmission [37], multipath data retrieval [10]
[11], fast loss recovery [15]. However, there remain several issues
to be considered.
There generally exist limitations in the CS capacity, and the caching
policy affects the consumer's performance [29] [34] [35]. It is thus
crucial for forwarders to determine which content objects should be
cached and which discarded. As delay-sensitive applications often do
not require an in-network cache for a long period owing to their
real-time constraints, forwarders have to know the necessity for
caching received content objects to save the caching volume. In
CCNx, this could be made possible by setting a Recommended Cache Time
(RCT) in the optional header of the data packet at the producer side.
The RCT serves as a guideline for the CS cache in determining how
long to retain the content object. When the RCT is set as zero, the
forwarder recognizes that caching the content object is not useful.
Conversely, the forwarder may cache it when the RCT has a greater
value. In NDN, the TLV type of FreshnessPeriod could be used.
One key aspect of in-network caching is whether or not forwarders can
cache NC packets in their CS. They may be caching the NC packets
without having the ability to perform a validation of the content
objects. Therefore, the caching of the NC packets would require some
mechanism to validate the NC packets (see Section 8). In the case
Matsuzono, et al. Expires August 31, 2022 [Page 14]
Internet-Draft NC for CCNx/NDN February 2022
wherein the NC packets have the same name, it would also require some
mechanism to identify them.
6.4. Seamless Consumer Mobility
A key feature of CCNx/NDN is that it is sessionless, which enables
the consumer and forwarder to send multiple interests toward
different copies of the content in parallel, by using multiple
interfaces at the same time in an asynchronous manner. Through the
multipath data retrieval, the consumer could obtain the content from
multiple copies that are distributed while using the aggregate
capacity of multiple interfaces. For the link between the consumer
and the multiple copies, the consumer can perform a certain rate
adaptation mechanism for video streaming [11] or congestion control
for content acquisition [12].
NC adds a reliability layer to CCNx in a distributed and asynchronous
manner, because NC provides a mechanism for ensuring that the
interests sent to multiple copies of the content in parallel retrieve
innovative packets, even in the case of packet losses on some of the
paths/networks to these copies. This applies to consumer mobility
events [11], wherein the consumer could receive additional degrees of
freedom with any innovative packet if at least one available
interface exists during the mobility event. An interest forwarding
strategy at the consumer (and possibly forwarder) for efficiently
obtaining innovative packets would be required for the consumer to
achieve seamless consumer mobility.
7. Challenges
This section presents several primary challenges and research items
to be considered when applying NC in CCNx/NDN.
7.1. Adoption of Convolutional Coding
Several block coding approaches have been proposed thus far; however,
there is still not sufficient discussion and application of the
convolutional coding approach (e.g., sliding or elastic window
coding) in CCNx/NDN. Convolutional coding is often appropriate for
situations wherein a fully or partially reliable delivery of
continuous data flows is required, and especially when these data
flows feature realtime constraints. As in [40], on an end-to-end
coding basis, it would be advantageous for continuous content flow to
adopt sliding window coding in CCNx/NDN. In this case, the producer
is required to appropriately set coding parameters and let the
consumer know the information, and the consumer is required to send
interests augmented with feedback information regarding the data
reception and/or decoding status. As CCNx/NDN utilises hop-by-hop
Matsuzono, et al. Expires August 31, 2022 [Page 15]
Internet-Draft NC for CCNx/NDN February 2022
forwarding state, it would be worth discussing and investigating how
convolutional coding can be applied in a hop-by-hop manner and what
benefits might accrue. In particular, in the case wherein in-network
re-coding could occur at forwarders, both the encoding window and CS
management would be required, and the corresponding feasibility and
practicality should be considered.
7.2. Rate and Congestion Control
The addition of redundancy using repair packets may result in further
network congestion and could adversely affect the overall throughput.
In particular, in a situation wherein fair bandwidth sharing is more
desirable, each streaming flow must adapt to the network conditions
to fairly consume the available link bandwidth. It is thus necessary
that each content flow cooperatively implement congestion control to
adjust the consumed bandwidth [22]. From this perspective, an
effective deployment approach (e.g., a forwarder-supported approach
that can provide benefits under partial deployment) is required.
As described in Section 6.4, NC can contribute to seamless consumer
mobility by obtaining innovative packets without receiving duplicated
packets through multipath data retrieval, and avoiding duplicated
packets has congestion control benefits as well. It can be
challenging to develop an effective rate and congestion control
mechanism in order to achieve seamless consumer mobility while
improving the overall throughput or latency by fully exploiting NC
operations.
7.3. Security
While CCNx/NDN introduces new security issues at the networking layer
that are different from the IP network, such as a cache poisoning and
pollution attacks, a DoS attack using interest packets, some security
approaches are already provided [24] [25]. The application of NC in
CCNx/NDN brings two potential security aspects that need to be dealt
with.
The first is in-network re-coding at forwarders. Some mechanism for
ensuring the integrity of the NC packets newly produced by in-network
re-coding is required in order for consumers or other forwarders to
receive valid NC packets. To this end, there are some possible
approaches described in Section 8, but there may be more effective
method with lower complexity and computation overhead.
The second is that attackers maliciously request and inject NC
packets, which could amplify some attacks. As NC packets are
unpopular in general use, they could be targeted by a cache pollution
attack that requests less popular content objects more frequently to
Matsuzono, et al. Expires August 31, 2022 [Page 16]
Internet-Draft NC for CCNx/NDN February 2022
undermine popularity-based caching by skewing the content popularity.
Such an attack needs to be dealt with in order to maintain the in-
network cache efficiency. By injecting invalid NC packets with the
goal of filling the CSs at the forwarders with them, the cache
poisoning attack could be effectual depending on the exact integrity
coverage on NC packets. On the assumption that each NC packet has
the valid signature, the straightforward approach would comprise the
forwarders verifying the signature within the NC packets in transit
and only transmitting and storing the validated NC packets. However,
as performing a signature verification by the forwarders may be
infeasible at line speed, some mechanisms should be considered for
distributing and reducing the load of signature verification, in
order to maintain in-network cache benefits such as latency and
network-load reduction.
7.4. Routing Scalability
In CCNx/NDN, a name-based routing protocol without a resolution
process streamlines the routing process and reduces the overall
latency. In IP routing, the growth in the routing table size has
become a concern. It is thus necessary to use a hierarchical naming
scheme in order to improve the routing scalability by enabling the
aggregation of the routing information.
To realize the benefits of NC, consumers need to efficiently obtain
innovative packets using multipath retrieval mechanisms of CCNx/NDN.
This would require some efficient routing mechanism to appropriately
set the FIB and also an efficient interest forwarding strategy. Such
routing coordination may create routing scalability issues. It would
be challenging to achieve effective and scalable routing for
interests requesting NC packets as well as to simplify the routing
process.
8. Security Considerations
In-network re-coding is a distinguishing feature of NC. Only valid
NC packets produced by in-network re-coding must be requested and
utilized (and possibly stored). To this end, there exist some
possible approaches. First, as a signature verification approach,
the exploitation of multi-signature capability could be applied.
This allows not only the original content producer but also some
forwarders responsible for in-network re-coding to have their own
unique signing key. Each forwarder of the group signs newly
generated NC packet in order for other nodes to be able to validate
the data with the signature. The CS may verify the signature within
the NC packet before storing it to avoid invalid data caching.
Second, as a consumer-dependent approach, the consumer puts a
restriction on the matching rule using only the name of the requested
Matsuzono, et al. Expires August 31, 2022 [Page 17]
Internet-Draft NC for CCNx/NDN February 2022
data. The interest ambiguity can be clarified by specifying both the
name and the key identifier (the producer's public key digest) used
for matching to the requested data. This KeyId restriction is built
in the CCNx design [1]. Only the requested data packet satisfying
the interest with the KeyId restriction would be forwarded and stored
in the CS, thus resulting in a reduction in the chances of cache
poisoning. Moreover, in the CCNx design, there exists the rule that
the CS obeys in order to avoid amplifying invalid data; if an
interest has a KeyID restriction, the CS must not reply unless it
knows that the signature on the matching content object is correct.
If the CS cannot verify the signature, the interest may be treated as
a cache miss and forwarded to the upstream forwarder(s). Third, as a
certificate chain management approach (possibly without certificate
authority), some mechanism such as [31] could be used to establish a
trustworthy data delivery path. This approach adopts the hop-by-hop
authentication mechanism, wherein forwarding-integrated hop-by-hop
certificate collection is performed to provide suspension certificate
chains such that the data retrieval is trustworthy.
Depending on the adopted caching strategy such as cache replacement
policies, forwarders should also take caution when storing and
retaining the NC packets in the CS as they could be targeted by cache
pollution attacks. In order to mitigate the cache pollution attacks'
impact, forwarders should check the content request frequencies to
detect the attack and may limit requests by ignoring some of the
consecutive requests. The forwarders can then decide to apply or
change to the other cache replacement mechanism.
The forwarders or producers require careful attention to the DoS
attacks aiming at provoking the high load of NC operations by using
the interests for NC packets. In order to mitigate such attacks, the
forwarders could adopt a rate-limiting approach. For instance, they
could monitor the PIT size growth for NC packets per content to
detect the attacks, and limit the interest arrival rate when
necessary. If the NC application wishes to secure an interest
(considered as the NC actuator) in order to prevent such attacks, the
application should consider using an encrypted wrapper and an
explicit protocol.
9. Acknowledgements
The authors would like to thank ICNRG and NWCRG members, especially
Marie-Jose Montpetit, David Oran, Vincent Roca, and Thierry Turletti,
for their valuable comments and suggestions on this document.
Matsuzono, et al. Expires August 31, 2022 [Page 18]
Internet-Draft NC for CCNx/NDN February 2022
10. Informative References
[1] Mosko, M. and et al., "Content-Centric Networking (CCNx)
Semantics", RFC 8569, July 2019,
<https://tools.ietf.org/html/rfc8569>.
[2] Gkantsidis, C. and P. Rodriguez, "Cooperative Security for
Network Coding File Distribution", Proc. Infocom, IEEE,
April 2006.
[3] Cai, N. and R. Yeung, "Secure network coding", Proc.
International Symposium on Information Theory
(ISIT), IEEE, June 2002.
[4] Lima, L., Gheorghiu, S., Barros, J., Medard, M., and A.
Toledo, "Secure Network Coding for Multi-Resolution
Wireless Video Streaming", IEEE Journal of Selected Area
(JSAC), vol. 28, no. 3, April 2010.
[5] Vilea, J., Lima, L., and J. Barros, "Lightweight security
for network coding", Proc. ICC, IEEE, May 2008.
[6] Dimarkis, A., Godfrey, P., Wu, Y., Wainwright, M., and K.
Ramchandran, "Network Coding for Distributed Storage
Systems", IEEE Trans. Information Theory, vol. 56, no.9,
September 2010.
[7] Gkantsidis, C. and P. Rodriguez, "Network coding for large
scale content distribution", Proc. Infocom, IEEE, March
2005.
[8] Seferoglu, H. and A. Markopoulou, "Opportunistic Network
Coding for Video Streaming over Wireless", Proc. Packet
Video Workshop (PV), IEEE, November 2007.
[9] Montpetit, M., Westphal, C., and D. Trossen, "Network
Coding Meets Information-Centric Networking: An
Architectural Case for Information Dispersion Through
Native Network Coding", Proc. Workshop on Emerging Name-
Oriented Mobile Networking Design (NoM), ACM, June 2012.
[10] Saltarin, J., Bourtsoulatze, E., Thomos, N., and T. Braun,
"NetCodCCN: a network coding approach for content-centric
networks", Proc. Infocom, IEEE, April 2016.
Matsuzono, et al. Expires August 31, 2022 [Page 19]
Internet-Draft NC for CCNx/NDN February 2022
[11] Ramakrishnan, A., Westphal, C., and J. Saltarin, "Adaptive
Video Streaming over CCN with Network Coding for Seamless
Mobility", Proc. International Symposium on Multimedia
(ISM), IEEE, December 2016.
[12] Mahdian, M., Arianfar, S., Gibson, J., and D. Oran,
"MIRCC: Multipath-aware ICN Rate-based Congestion
Control", Proc. Conference on Information-Centric
Networking (ICN), ACM, September 2016.
[13] Wang, J., Ren, J., Lu, K., Wang, J., Liu, S., and C.
Westphal, "An Optimal Cache Management Framework for
Information-Centric Networks with Network Coding", Proc.
Networking Conference, IFIP/IEEE, June 2014.
[14] Wang, J., Ren, J., Lu, K., Wang, J., Liu, S., and C.
Westphal, "A Minimum Cost Cache Management Framework for
Information-Centric Networks with Network Coding",
Computer Networks, Elsevier, August 2016.
[15] Matsuzono, K., Asaeda, H., and T. Turletti, "Low Latency
Low Loss Streaming using In-Network Coding and Caching",
Proc. Infocom, IEEE, May 2017.
[16] Jacobson, V., Smetters, D., Thornton, J., Plass, M.,
Briggs, N., and R. Braynard, "Networking Named Content",
Proc. CoNEXT, ACM, December 2009.
[17] Wissingh, B. and et al., "Information-Centric Networking
(ICN): Content-Centric Networking (CCNx) and Named Data
Networking (NDN) Terminology", RFC 8793, June 2020,
<https://tools.ietf.org/html/rfc8793>.
[18] Mosko, M. and et al., "Content-Centric Networking (CCNx)
Messages in TLV Format", RFC 8609, July 2019,
<https://tools.ietf.org/html/rfc8609>.
[19] Zhang, L., Afanasyev, A., Burke, J., Jacobson, V., Claffy,
K., Crowley, P., Papadopoulos, C., Wang, L., and B. Zhang,
"Named data networking", ACM Comput. Commun. Rev., vol.
44, no. 3, July 2014.
[20] Koetter, R. and M. Medard, "An Algebraic Approach to
Network Coding", IEEE/ACM Trans. on Networking, vol. 11,
no 5, Oct. 2003.
Matsuzono, et al. Expires August 31, 2022 [Page 20]
Internet-Draft NC for CCNx/NDN February 2022
[21] Adamson, B. and et al., "Taxonomy of Coding Techniques for
Efficient Network Communications", RFC 8406, June 2018,
<https://tools.ietf.org/html/rfc8406>.
[22] Kuhn, N., Lochin, E., Michel, F., and M. Welzl, "Coding
and Congestion Control in Transport", Work in Progress,
draft-irtf-nwcrg-coding-and-congestion-09, June 2021.
[23] Tschudin, C., Wood, C., Mosko, M., and D. Oran, "File-Like
ICN Collections (FLIC)", Work in Progress, draft-irtf-
icnrg-flic-03, Nov. 2021.
[24] Kutscher, D. and et al., "Information-Centric Networking
(ICN) Research Challenges", RFC 7927, July 2016.
[25] Pentikousis, K. and et al., "Information-Centric
Networking: Evaluation and Security Considerations",
RFC 7945, July 2019.
[26] Watson, M. and et al., "Forward Error Correction (FEC)
Framework", RFC 6363, Oct. 2011.
[27] Thomos, N. and P. Frossard, "Toward one Symbol Network
Coding Vectors", IEEE Communications letters, vol. 16, no.
11, November 2012.
[28] Lucani, D., Pedersen, M., Heide, J., and F. Fitzek,
"Fulcrum Network Codes: A Code for Fluid Allocation of
Complexity", available at http://arxiv.org/abs/1404.6620,
April 2014.
[29] Perino, D. and M. Varvello, "A reality check for content
centric networking", Proc. SIGCOMM Workshop on
Information-centric networking (ICN'11), ACM, August 2011.
[30] Wu, Q., Li, Z., Tyson, G., Uhlig, S., Kaafar, M., and G.
Xie, "Privacy-Aware Multipath Video Caching for Content-
Centric Networks", IEEE Journal of Selected Area
(JSAC) vol. 38, no. 8, June 2016.
[31] Li, R., Asaeda, H., and J. Wu, "DCAuth: Data-Centric
Authentication for Secure In-Network Big-Data Retrieval",
IEEE Trans. on Network Science and Engineering vol. 7, no.
1, September 2018.
[32] Wu, Y., Chou, P., and K. Jain, "A comparison of network
coding and tree packing", Proc. ISIT, IEEE, June 2004.
Matsuzono, et al. Expires August 31, 2022 [Page 21]
Internet-Draft NC for CCNx/NDN February 2022
[33] Ho, T., Medard, M., Koetter, R., Karger, R., Effros, D.,
Shi, M., and B. Leong, "A Random Linear Network Coding
Approach to Multicast", IEEE Trans. Information
Theory, vol. 52, no.10, October 2006.
[34] Podlipnig, S. and L. Osz, "A Survey of Web Cache
Replacement Strategies", Proc. ACM Computing Surveys vol.
35, no. 4, December 2003.
[35] Rossini, G. and D. Rossi, "Evaluating CCN multi-path
interest forwarding strategies", Elsevier Computer
Communication, vol.36, no. 7, April 2013.
[36] Carofiglio, G., Muscariello, L., Papalini, M., Rozhnova,
N., and X. Zeng, "Leveraging ICN In-network Control for
Loss Detection and Recovery in Wireless Mobile networks",
Proc. ICN ACM, September 2016.
[37] Ali, M. and U. Niesen, "Coding for Caching: Fundamental
Limits and Practical Challenges", IEEE Communications
Magazine vol. 54, no. 8, August 2016.
[38] Koetter, R. and F. Kschischang, "An algebraic approach to
network coding", IEEE Trans. Netw. vol.11, no.5, October
2003.
[39] Vyetrenko, S., Ho, T., Effros, M., Kliewer, J., and E.
Erez, "Rate regions for coherent and noncoherent
multisource network error correction", Proc. International
Symposium on Information Theory (ISIT), IEEE, July 2009.
[40] Tournoux, P., Lochin, E., Lacan, J., Bouabdallah, A., and
V. Roca, "On-the-Fly Erasure Coding for Real-Time Video
Applications", IEEE Trans. Multimeda vol.13, no.4, August
2011.
Authors' Addresses
Kazuhisa Matsuzono
National Institute of Information and Communications Technology
4-2-1 Nukui-Kitamachi
Koganei, Tokyo 184-8795
Japan
Email: matsuzono@nict.go.jp
Matsuzono, et al. Expires August 31, 2022 [Page 22]
Internet-Draft NC for CCNx/NDN February 2022
Hitoshi Asaeda
National Institute of Information and Communications Technology
4-2-1 Nukui-Kitamachi
Koganei, Tokyo 184-8795
Japan
Email: asaeda@nict.go.jp
Cedric Westphal
Huawei
2330 Central Expressway
Santa Clara, California 95050
USA
Email: cedric.westphal@futurewei.com,
Matsuzono, et al. Expires August 31, 2022 [Page 23]
