Internet DRAFT - draft-ietf-rtgwg-lfa-applicability

draft-ietf-rtgwg-lfa-applicability






Network Working Group                                  Clarence Filsfils
Internet-Draft                                             Cisco Systems
Intended status: Informational                           Pierre Francois
Expires: July 21, 2012                          Institute IMDEA Networks
                                                        January 18, 2012


                    LFA applicability in SP networks
                 draft-ietf-rtgwg-lfa-applicability-06

Abstract

   In this document, we analyze the applicability of the Loop-Free
   Alternates method of providing IP fast re-route in both the core and
   the access parts of Service Provider networks.  We consider both the
   link and node failure cases, and provide guidance on the
   applicability of LFA to different network topologies, with special
   emphasis on the access parts of the network.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on July 21, 2012.

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of



Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 1]

Internet-Draft      LFA applicability in SP networks        January 2012


   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.


Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  4
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  4
   3.  Access Network . . . . . . . . . . . . . . . . . . . . . . . .  7
     3.1.  Triangle . . . . . . . . . . . . . . . . . . . . . . . . .  8
       3.1.1.  E1C1 failure . . . . . . . . . . . . . . . . . . . . .  9
       3.1.2.  C1E1 failure . . . . . . . . . . . . . . . . . . . . .  9
       3.1.3.  uLoop  . . . . . . . . . . . . . . . . . . . . . . . . 10
       3.1.4.  Conclusion . . . . . . . . . . . . . . . . . . . . . . 10
     3.2.  Full-Mesh  . . . . . . . . . . . . . . . . . . . . . . . . 10
       3.2.1.  E1A1 failure . . . . . . . . . . . . . . . . . . . . . 11
       3.2.2.  A1E1 failure . . . . . . . . . . . . . . . . . . . . . 12
       3.2.3.  A1C1 failure . . . . . . . . . . . . . . . . . . . . . 12
       3.2.4.  C1A1 failure . . . . . . . . . . . . . . . . . . . . . 13
       3.2.5.  uLoop  . . . . . . . . . . . . . . . . . . . . . . . . 13
       3.2.6.  Conclusion . . . . . . . . . . . . . . . . . . . . . . 13
     3.3.  Square . . . . . . . . . . . . . . . . . . . . . . . . . . 13
       3.3.1.  E1A1 failure . . . . . . . . . . . . . . . . . . . . . 14
       3.3.2.  A1E1 failure . . . . . . . . . . . . . . . . . . . . . 15
       3.3.3.  A1C1 failure . . . . . . . . . . . . . . . . . . . . . 15
       3.3.4.  C1A1 failure . . . . . . . . . . . . . . . . . . . . . 16
       3.3.5.  Conclusion . . . . . . . . . . . . . . . . . . . . . . 17
       3.3.6.  A square might become a full-mesh  . . . . . . . . . . 18
       3.3.7.  A full-mesh might be more economical than a square . . 18
     3.4.  Extended U . . . . . . . . . . . . . . . . . . . . . . . . 18
       3.4.1.  E1A1 failure . . . . . . . . . . . . . . . . . . . . . 20
       3.4.2.  A1E1 failure . . . . . . . . . . . . . . . . . . . . . 20
       3.4.3.  A1C1 failure . . . . . . . . . . . . . . . . . . . . . 21
       3.4.4.  C1A1 failure . . . . . . . . . . . . . . . . . . . . . 21
       3.4.5.  Conclusion . . . . . . . . . . . . . . . . . . . . . . 22
     3.5.  Dual-plane Core and its impact on the Access LFA
           analysis . . . . . . . . . . . . . . . . . . . . . . . . . 22
     3.6.  Two-tiered IGP metric allocation . . . . . . . . . . . . . 22
     3.7.  uLoop analysis . . . . . . . . . . . . . . . . . . . . . . 22
     3.8.  Summary  . . . . . . . . . . . . . . . . . . . . . . . . . 23
   4.  Core Network . . . . . . . . . . . . . . . . . . . . . . . . . 24
     4.1.  Simulation Framework . . . . . . . . . . . . . . . . . . . 25
     4.2.  Data Set . . . . . . . . . . . . . . . . . . . . . . . . . 26
     4.3.  Simulation results . . . . . . . . . . . . . . . . . . . . 26
   5.  Core and Access protection schemes are independent . . . . . . 27
   6.  Simplicity and other LFA benefits  . . . . . . . . . . . . . . 27
   7.  Capacity Planning with LFA in mind . . . . . . . . . . . . . . 28
     7.1.  Coverage Estimation - Default Topology . . . . . . . . . . 28



Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 2]

Internet-Draft      LFA applicability in SP networks        January 2012


     7.2.  Coverage estimation in relation to traffic . . . . . . . . 29
     7.3.  Coverage verification for a given set of demands . . . . . 29
     7.4.  Modeling - What-if Scenarios - Coverage impact . . . . . . 29
     7.5.  Modeling - What-if Scenarios - Load impact . . . . . . . . 30
     7.6.  Discussion on metric recommendations . . . . . . . . . . . 30
   8.  Security Considerations  . . . . . . . . . . . . . . . . . . . 31
   9.  IANA considerations  . . . . . . . . . . . . . . . . . . . . . 31
   10. Conclusions  . . . . . . . . . . . . . . . . . . . . . . . . . 32
   11. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 32
   12. Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . . 33
   13. References . . . . . . . . . . . . . . . . . . . . . . . . . . 33
     13.1. Normative References . . . . . . . . . . . . . . . . . . . 33
     13.2. Informative References . . . . . . . . . . . . . . . . . . 33
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 33





































Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 3]

Internet-Draft      LFA applicability in SP networks        January 2012


1.  Introduction

   In this document, we analyze the applicability of the Loop-Free
   Alternates (LFA) [RFC5714] [RFC5286] method of providing IP fast re-
   route (IPFRR) in both the core and the access parts of Service
   Provider (SP) networks.  We consider both the link and node failure
   cases, and provide guidance on the applicability of LFA to different
   network topologies, with special emphasis on the access parts of the
   network.

   We first introduce the terminology used in this document in
   Section 2.  In Section 3, we describe typical access network designs
   and we analyze them for LFA applicability.  In Section 4, we describe
   a simulation framework for the study of LFA applicability in SP core
   networks, and present results based on various SP networks.  We then
   emphasize the independence between protection schemes used in the
   core and at the access level of the network.  Finally we discuss the
   key benefits of LFA which stem from its simplicity and we draw some
   conclusions.


2.  Terminology

   We use IS-IS [RFC1195] as reference.  It is assumed that normal
   routing (i.e., when traffic not being fast re-routed around a
   failure) occurs along the shortest path.  The analysis is equally
   applicable to OSPF [RFC2328] [RFC5340].

   A per-prefix LFA for a destination D at a node S is a precomputed
   backup IGP nexthop for that destination.  This backup IGP nexthop can
   be link protecting or node protecting.  In this document, we assume
   that all links to be protected with LFAs are point-to-point.

   Link-protecting: A neighbor N is a link-protecting per-prefix LFA for
   S's route to D if equation eq1 is satisfied, with eq1 == ND < NS + SD
   where XY refers to the IGP distance from X to Y. This is in line with
   the definition of an LFA in [RFC5714].


                            eq1 == ND < NS + SD


                               Equation eq1

   Node-protecting: A Neighbor N is a node-protecting LFA for S's route
   to D, with initial IGP nexthop F if N is a link-protecting LFA for D
   and equation eq2 is satisfied, with eq2 == ND < NF + FD.  This is in
   line with the definition of a Node-Protecting Alternate Next-Hop in



Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 4]

Internet-Draft      LFA applicability in SP networks        January 2012


   [RFC5714].


                            eq2 == ND < NF + FD


                               Equation eq2

   De facto node-protecting LFA: this is a link-protecting LFA that
   turns out to be node-protecting.  This occurs in cases illustrated by
   the following examples :
   o  The LFA candidate that is picked by S actually satisfies Equation
      eq2 but S did not verify that property.  The show command issued
      by the operator would not indicate this LFA as "node protecting"
      while in practice (de facto) it is.
   o  A cascading effect of multiple LFA's can also provide de facto
      node protection.  Equation eq2 is not satisfied, but the combined
      activation of LFAs by some other neighbors of the failing node F
      provides (de facto) node protection.  In other words, it puts the
      dataplane in a state such that packets forwarded by S ultimately
      reach a neighbor of F that has a node-protecting LFA.  Note that
      in this case S cannot indicate the node-protecting behavior of the
      repair without running additional computations.

   Per-Link LFA: a per-link LFA for the link SF is one precomputed
   backup IGP nexthop for all the destinations reached through SF.  This
   is a neighbor of the repairing node that is a per-Prefix LFA for all
   the destinations that the repairing node reaches through SF.  Note
   that such a per-link LFA exists if S has a per-prefix LFA for
   destination F.





















Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 5]

Internet-Draft      LFA applicability in SP networks        January 2012


                                    D
                                   / \
                               10 /   \ 10
                                 /     \
                                G       H----------.
                                |       |          |
                              1 |     1 |          |
                                |       |          |
                                B       C          | 10
                                |       |\         |
                                |       | \        |
                                |       |  \ 6     |
                                |       |   \      |
                              7 |    10 |    E     F
                                |       |   /     /
                                |       |  / 6   / 5
                                |       | /     /
                                |       |/     /
                                A-------S-----/
                                    7


                            Figure 1: Example 1

   In Figure 1, considering the protection of link SC, we can see that
   A, E, and F are per-prefix LFAs for destination D, as none of them
   use S to reach D.

   For destination D, A and F are node-protecting LFA as they do not
   reach D through node C, while E is not node-protecting for S as it
   reaches D through C.

   If S does not compute and select node-protecting LFAs, there is a
   chance that S picks the non node-protecting LFA E, although A and F
   were node-protecting LFAs.  If S enforces the selection of node-
   protecting LFAs, then in the case of the single failure of link SC, S
   will first activate its LFA and deviate traffic addressed to D along
   S-A-B-G-D and/or S-F-H-D, and then converge to its post-convergence
   optimal path S-E-C-H-D.

   A is not a per-link LFA for link SC because A reaches C via S. E is a
   per-Link LFA for link SC as it reaches C through link EC.  This per-
   link LFA does not provide de facto node protection.  Upon failure of
   node C, S would fast-reroute D-destined packets to its per-link lfa
   (= E).  E would himself detect the failure of EC and hence activate
   its own per-link LFA (=S).  Traffic addressed to D would be trapped
   in a loop and hence there is no de facto node protection behavior.




Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 6]

Internet-Draft      LFA applicability in SP networks        January 2012


   If there were a link between E and F, that E would pick as its LFA
   for destination D, then E would provide de facto node protection for
   S, as upon the activation of its LFA, S would deviate traffic
   addressed to D towards E, which in turns deviates that traffic to F,
   which does not reach D through C.

   F is a per-Link LFA for link SC as F reaches C via H. This per-link
   LFA is de facto node-protecting for destination D as F reaches D via
   F-H-D.

   MicroLoop (uLoop): the occurrence of a transient forwarding loop
   during a routing transition (as defined in [RFC5714]).

   In Figure 1, the loss of link SE cannot create any uLoop because:
   1/The link is only used to reach destination E and 2/ S is the sole
   node changing its path to E upon link SE failure. 3/ S's shortest
   path to E after the failure goes via C. 4/C's best path to E (before
   and after link SC failure) is via CE.

   To the contrary, upon failure of link AB, a microloop may form for
   traffic destined to B. Indeed, if A updates its FIB before S, A will
   deviate B-destined traffic towards S, while S is still forwarding
   this traffic to A.


3.  Access Network

   The access part of the network often represents the majority of the
   nodes and links.  It is organized in several tens or more of regions
   interconnected by the core network.  Very often the core acts as an
   IS-IS level2 domain (OSPF area 0) while each access region is
   confined in an IS-IS level1 domain (OSPF non 0 area).  Very often,
   the network topology within each access region is derived from a
   unique template common across the whole access network.  Within an
   access region itself, the network is made of several aggregation
   regions, each following the same interconnection topologies.

   For these reasons, in the next sections, we base the analysis of the
   LFA applicability in a single access region, with the following
   assumptions:
   o  Two routers (C1 and C2) provide connectivity between the access
      region and the rest of the network.  If a link connects these two
      routers in the region area, then it has a symmetric IGP metric c.
   o  We analyze a single aggregation region within the access region.
      Two aggregation routers (A1 and A2) interconnect the aggregation
      region to the two routers C1 and C2 for the analyzed access
      region.  If a link connects A1 to A2 then it has a symmetric IGP
      metric a.  If a link connects an A to a C router then, for sake of



Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 7]

Internet-Draft      LFA applicability in SP networks        January 2012


      generality, we will call d the metric for the directed link CA and
      u the metric for the AC directed link.
   o  We analyze two edge routers E1 and E2 in the access region.  Each
      is either dual-homed directly into C1 and C2 (Section 3.1) or into
      A1 and A2 (Section 3.2, Section 3.3, Section 3.4 ).  The directed
      link metric between Cx/Ax and Ey is d and u in the opposite
      direction.
   o  We assume a multi-level IGP domain.  The analyzed access region
      forms a level-1 (L1) domain.  The core is the level-2 (L2) domain.
      We assume that the link between C1 and C2, if it exists, is
      configured as L1L2.  We assume that the loopbacks of the C routers
      are part of the L2 topology.  L1 routers learn about them as
      propagated routes (L2=>L1 with Down bit set).  We remind that if
      an L1L2 router learns about X/x as an L1 path P1, an L2 path P2
      and an L1L2 path P12, then it will prefer path P1.  If P1 is lost,
      then it will prefer path P2.
   o  We assume that all the C, A and E routers may be connected to
      customers and hence we analyze LFA coverage for the loopbacks of
      each type of node.
   o  We assume that no useful traffic is directed to router-to-router
      subnets and hence we do not analyze LFA applicability for these.
   o  A prefix P models an important IGP destination that is not present
      in the local access region.  The igp metric from C1 to P is x and
      the metric from C2 to P is x+e.
   o  We analyze LFA coverage against all link and node failures within
      the access region.
   o  WxYz refers to the link from Wx to Yz.
   o  We assume that c < d + u and a < d + u (commonly agreed design
      rule).
   o  In the square access design (Section 3.3), we assume that c < a
      (commonly agreed design rule).
   o  We analyze the most frequent topologies found in an access region.
   o  We first analyze per-prefix LFA applicability and then per-link.
   o  The topologies are symmetric with respect to a vertical axe and
      hence we only detail the logic for the link and node failures of
      the left half of the topology.

3.1.  Triangle

   We describe the LFA applicability for the failures of each direction
   of link C1E1, E1 and C1 (Figure 2), and for the failure of each node.










Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 8]

Internet-Draft      LFA applicability in SP networks        January 2012


                                      P
                                     / \
                                   x/   \x+e
                                   /     \
                                  C1--c--C2
                                   |\    /|
                                d/u|  \/  |d/u
                                   | /  \ |
                                   E1     E2

                            Figure 2: Triangle

3.1.1.  E1C1 failure

3.1.1.1.  Per-Prefix LFA

   Three destinations are impacted by this link failure: C1, E2 and P.

   The LFA for destination C1 is C2 because eq1 == c < d + u.  Node
   protection for route C1 is not applicable. (if C1 goes down, traffic
   destined to C1 is lost anyway).

   The LFA to E2 is via C2 because eq1 == d < d+u+d.  It is node
   protecting because eq2 == d < c + d.

   The LFA to P is via C2 because eq1 == c < d + u.  It is node
   protecting if eq2 == x + e < x + c, i.e., if e < c.  This
   relationship between e and c is an important aspect of the analysis,
   which is discussed in detail in Section 3.5 and Section 3.6

   Conclusion: all important intra-PoP routes with primary interface
   E1C1 benefit from LFA link and node protection.  All important inter-
   PoP routes with primary interface E1C1 benefit from LFA link
   protection, and also from node protection if e < c.

3.1.1.2.  Per-Link LFA

   We have a per-prefix LFA to C1 and hence we have a per-link LFA for
   link E1C1.  All impacted destinations are protected for link failure.
   In case of C1 node failure, the traffic to C1 is lost (by
   definition), the traffic to E2 is de facto protected against node
   failure and the traffic to P is de facto protected when e < c.

3.1.2.  C1E1 failure







Clarence Filsfils & Pierre Francois  Expires July 21, 2012      [Page 9]

Internet-Draft      LFA applicability in SP networks        January 2012


3.1.2.1.  Per-Prefix LFA

   C1 has one single primary route via C1E1: the route to E1 (because c
   < d + u).

   C1's LFA to E1 is via C2 because eq1 == d < c + d.

   Node protection upon E1's failure is not applicable as the only
   impacted traffic is sinked at E1 and hence is lost anyway.

   Conclusion: all important routes with primary interface C1E1 benefit
   from LFA link protection.  Node protection is not applicable.

3.1.2.2.  Per-Link LFA

   We have a per-prefix LFA to E1 and hence we have a per-link LFA for
   link C1E1.  De facto node protection is not applicable.

3.1.3.  uLoop

   The IGP convergence cannot create any uLoop.  See Section 3.7.

3.1.4.  Conclusion

   All important intra-PoP routes benefit from LFA link and node
   protection or de facto node protection.  All important inter-PoP
   routes benefit from LFA link protection.  De facto node protection is
   ensured if e < c (this is particularly the case for dual-plane core
   or two-tiered-igp-metric design, see later sections).

   The IGP convergence does not cause any uLoop.

   Per-link LFA and per-Prefix LFA provide the same protection benefits.

3.2.  Full-Mesh

   We describe the LFA applicability for the failures of C1A1, A1E1, E1,
   A1 and C1 (Figure 3).













Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 10]

Internet-Draft      LFA applicability in SP networks        January 2012


                                          P
                                         / \
                                       x/   \x+e
                                       /     \
                                      C1--c--C2
                                       |\   /|
                                       | \ / |
                                   d/u |  \  | d/u
                                       | / \ |
                                       |/   \|
                                      A1--a--A2
                                       |\    /|
                                    d/u|  \/  |d/u
                                       | /  \ |
                                       E1     E2

                            Figure 3: Full-Mesh

3.2.1.  E1A1 failure

3.2.1.1.  Per-Prefix LFA

   Four destinations are impacted by this link failure: A1, C1, E2 and
   P.

   The LFA for A1 is A2: eq1 == a < d + u.  Node protection for route A1
   is not applicable (if A1 goes down, traffic to A1 is lost anyway).

   The LFA for C1 is A2: eq1 == u < d + u + u.  Node protection for
   route C1 is guaranteed: eq2 == u < a + u.

   The LFA to E2 is via A2: eq1 == d < d+u+d.  Node protection is
   guaranteed: eq2 == d < a + d.

   The LFA to P is via A2: eq1 == u + x < d + u + u + x.  Node
   protection is guaranteed: eq2 == u+ x < a + u + x.

   Conclusion: all important intra-PoP and inter-PoP routes with primary
   interface E1A1 benefit from LFA link and node protection.

3.2.1.2.  Per-Link LFA

   We have a per-prefix LFA to A1 and hence we have a per-link LFA for
   link E1A1.  All impacted destinations are protected for link failure.
   De facto node protection is provided for all destinations (except to
   A1 which is not applicable).





Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 11]

Internet-Draft      LFA applicability in SP networks        January 2012


3.2.2.  A1E1 failure

3.2.2.1.  Per-Prefix LFA

   A1 has one single primary route via A1E1: the route to E1 (because c
   < d + u).

   A1's LFA to E1 is via A2: eq1 == d < a + d.

   Node protection upon E1's failure is not applicable as the only
   impacted traffic is sinked at E1 and hence is lost anyway.

   Conclusion: all important routes with primary interface A1E1 benefit
   from LFA link protection.  Node protection is not applicable.

3.2.2.2.  Per-Link LFA

   We have a per-prefix LFA to E1 and hence we have a per-link LFA for
   link C1E1.  De facto node protection is not applicable.

3.2.3.  A1C1 failure

3.2.3.1.  Per-Prefix LFA

   Two destinations are impacted by this link failure: C1 and P.

   The LFA for C1 is C2 because eq1 == c < d + u.  Node protection for
   route C1 is not applicable (if C1 goes down, traffic to C1 is lost
   anyway).

   The LFA for P is via C2 because eq1 == c < d + u.  It is de facto
   protected for node failure if eq2 == x + e < x + c.

   Conclusion: all important intra-PoP routes with primary interface
   A1C1 benefit from LFA link protection (node protection is not
   applicable).  All important inter-PoP routes with primary interface
   E1C1 benefit from LFA link protection (and from de facto node
   protection if e < c).

3.2.3.2.  Per-Link LFA

   We have a per-prefix LFA to C1 and hence we have a per-link LFA for
   link A1C1.  All impacted destinations are protected for link failure.
   In case of C1 node failure, the traffic to C1 is lost (by definition)
   and the traffic to P is de facto node protected if e < c.






Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 12]

Internet-Draft      LFA applicability in SP networks        January 2012


3.2.4.  C1A1 failure

3.2.4.1.  Per-Prefix LFA

   C1 has three routes via C1A1: A1, E1 and E2.  E2 behaves like E1 and
   hence is not analyzed further.

   C1's LFA to A1 is via C2 because we assumed c < a and eq1 == d < c +
   d.  Node protection upon A1's failure is not applicable as the
   traffic to A1 is lost anyway.

   C1's LFA to E1 is via A2: eq1 == d < u+ d + d.  Node protection upon
   A1's failure is guaranteed because: eq2 == d < a + d.

   Conclusion: all important routes with primary interface C1A1 benefit
   from LFA link protection.  Node protection is guaranteed where
   applicable.

3.2.4.2.  Per-Link LFA

   We have a per-prefix LFA to A1 and hence we have a per-link LFA for
   link C1E1.  De facto node protection is available.

3.2.5.  uLoop

   The IGP convergence cannot create any uLoop.  See Section 3.7.

3.2.6.  Conclusion

   All important intra-PoP routes benefit from LFA link and node
   protection.

   All important inter-PoP routes benefit from LFA link protection.
   They benefit from node protection upon failure of A nodes.  They
   benefit from node protections upon failure of C nodes if e < c (this
   is particularly the case for dual-plane core or two-tiered-igp-metric
   design, see later sections).

   The IGP convergence does not cause any uLoop.

   Per-link LFA and per-Prefix LFA provide the same protection benefits.

3.3.  Square

   We describe the LFA applicability for the failures of C1A1, A1E1, E1,
   A1 and C1 (Figure 4).





Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 13]

Internet-Draft      LFA applicability in SP networks        January 2012


                                      P
                                     / \
                                   x/   \x+e
                                   /     \
                                  C1--c--C2
                                   |\    | \
                                   | \   |  +-------+
                               d/u |  \  |           \
                                   |   +-|-----+      \
                                   |     |      \      \
                                  A1--a--A2     A3--a--A4
                                   |\    /|      |    /
                                d/u|  \/  |d/u   |  /
                                   | /  \ |      |/
                                   E1     E2     E3

                             Figure 4: Square

3.3.1.  E1A1 failure

3.3.1.1.  Per-Prefix LFA

   E1 has six routes via E1A1: A1, C1, P, E2, A3, E3.

   E1's LFA route to A1 is via A2 because eq1 == a < d + u.  Node
   protection for traffic to A1 upon A1 node failure is not applicable.

   E1's LFA route to A3 is via A2 because eq1 == u + c + d < d + u + u +
   d.  This LFA is guaranteed to be node protecting because eq2 == u + c
   + d < a + u + d.

   E1's LFA route to C1 is via A2 because eq1 == u + c < d + u + u.
   This LFA is guaranteed to be node protecting because eq2 == u + c < a
   + u.

   E1's primary route to E2 is via ECMP(E1A1, E1A2).  The LFA for the
   first ECMP path (via A1) is the second ECMP path (via A2).  This LFA
   is guaranteed to be node protecting because eq2 == d < a + d.

   E1's primary route to E3 is via ECMP(E1A1, E1A2).  The LFA for the
   first ECMP path (via A1) is the second ECMP path (via A2).  This LFA
   is guaranteed to be node protecting because eq2 == u + d + d < a + u
   d + d.

   If e=0: E1's primary route to P is via ECMP(E1A1, E1A2).  The LFA for
   the first ECMP path (via A1) is the second ECMP path (via A2).  This
   LFA is guaranteed to be node protecting because eq2 == u + x + 0 < a
   + u + x .



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 14]

Internet-Draft      LFA applicability in SP networks        January 2012


   If e<>0: E1's primary route to P is via E1A1.  Its LFA is via A2
   because eq1 == u + c + x < d + u + u + x.  This LFA is guaranteed to
   be node protecting because eq2 == u + c + x < a + u + x.

   Conclusion: all important intra-PoP and inter-PoP routes with primary
   interface E1A1 benefit from LFA link protection and node protection.

3.3.1.2.  Per-Link LFA

   We have a per-prefix LFA for A1 and hence we have a per-link LFA for
   link E1A1.  All important intra-PoP and inter-PoP routes with primary
   interface E1A1 benefit from LFA per-link protection and de facto node
   protection.

3.3.2.  A1E1 failure

3.3.2.1.  Per-Prefix LFA

   A1 has one single primary route via A1E1: the route to E1.

   A1's LFA for route E1 is the path via A2 because eq1 == d < a + d.
   Node protection is not applicable.

   Conclusion: all important routes with primary interface A1E1 benefit
   from LFA link protection.  Node protection is not applicable.

3.3.2.2.  Per-Link LFA

   All important routes with primary interface A1E1 benefit from LFA
   link protection.  De facto node protection is not applicable.

3.3.3.  A1C1 failure

3.3.3.1.  Per-Prefix LFA

   Four destinations are impacted when A1C1 fails: C1, A3, E3, and P.

   A1's LFA to C1 is via A2 because eq1 == u + c < a + u.  Node
   protection property is not applicable for traffic to C1 when C1
   fails.

   A1's LFA to A3 is via A2 because eq1 == u + c + d < a + u + d.  It is
   de facto node protecting as a < u + c + d (as we assumed a < u + d).
   Indeed A2 forwards traffic destined to A3 to C2, and C2 has a node
   protecting LFA for A3, for the failure of C2C1, being A4, as a < u +
   c + d.  Hence the cascading application of LFAs by A1 and C2 during
   the failure of C1 provides de facto node protection.




Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 15]

Internet-Draft      LFA applicability in SP networks        January 2012


   A1's LFA to E3 is via A2 because eq1 == u + d + d < a + u + d + d.
   It is node protecting because eq2 == u + d + d < u + c + d + d.

   A1's primary route to P is via C1 (even if e=0, u+x < u + c + x).
   The LFA is via A2 because eq1 == [u + c + x < a + u + x].  This LFA
   is node protecting (from the viewpoint of A1 computing eq2) if eq2 ==
   u + x + e < u + c + x hence if e < c.

   Conclusion: all important intra-PoP routes with primary interface
   A1C1 benefit from LFA link protection and node protection.  Note that
   A3 benefits from a de facto node protection.  All important inter-PoP
   routes with primary interface A1C1 benefit from LFA link protection.
   They also benefit from node protection if e < c.

3.3.3.2.  Per-Link LFA

   All important intra-PoP routes with primary interface A1C1 benefit
   from LFA link protection and de facto node protection.  All important
   inter-PoP routes with primary interface A1C1 benefit from LFA link
   protection.  They also benefit from de facto node protection if e <
   c.

3.3.4.  C1A1 failure

3.3.4.1.  Per-Prefix LFA

   Three destinations are impacted by C1A1 link failure: A1, E1 and E2.
   E2's analysis is the same as E1 and hence is omitted.

   C1's has no LFA for A1.  Indeed, all its neighbors (C2 and A3) have a
   shortest path to A1 via C1.  This is due to the assumption (c < a).

   C1's LFA for E1 is via C2 because eq1 == d + d < c + d + d.  It
   provides node protection because eq2 == d + d < d + a + d.

   Conclusion: all important intra-PoP routes with primary interface
   A1C1 except A1 benefit from LFA link protection and node protection.

3.3.4.2.  Per-Link LFA

   C1 does not have a per-prefix LFA for destination A1 and hence there
   is no per-link LFA for the link C1A1.

3.3.4.3.  Assumptions on the values of c and a

   The commonly agreed design rule (c < a) is especially beneficial for
   a deployment using per-link LFA: it provides a per-link LFA for the
   most important direction (A1C1).  Indeed, there are many more



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 16]

Internet-Draft      LFA applicability in SP networks        January 2012


   destinations reachable over A1C1 than over C1A1.  As the IGP
   convergence duration is proportional to the number of routes to
   update, there is a better benefit in leveraging LFA FRR for the link
   A1C1 than the link C1A1.

   Note as well that the consequence of this assumption is much more
   important for per-link LFA than for per-prefix LFA.

   For per-prefix LFA, in case of link C1A1 failure, we do have a per-
   prefix LFA for E1, E2 and any node subtended below A1 and A2.
   Typically most of the traffic traversing the link C1A1 is directed to
   these E nodes and hence the lack of per-prefix LFA for the
   destination A1 might be insignificant.  This is a good example of the
   coverage benefit of per-prefix LFA over per-link LFA.

   In the remainder of this section we analyze the consequence of not
   having c < a.

   It definitely has a negative impact upon per-link LFA.

   With c >= a, C1A1 has a per-link LFA while A1C1 has no per-link LFA.
   The number of destinations impacted by A1C1 failure is much larger
   than the direction C1A1 and hence the protection is provided for the
   wrong direction.

   For per-prefix LFA, the availability of an LFA depends on the
   topology and needs to be assessed individually for each per-prefix.
   Some backbone topologies will lead to very good protection coverage,
   some others might provide very poor coverage.

   More specifically, the coverage upon A1C1 failure of a remote
   destination P depends on whether e < a.  In such case, A2 is a de-
   facto node-protecting per-prefix LFA for P.

   Such a study likely requires a planning tool as each remote
   destination P would have a different e value (exception: all the edge
   devices of other aggregation pairs within the same region as for
   these e=0 by definition, e.g.  E3).

   Finally note that c = a is the worst choice as in this case C1 has no
   per-prefix LFA for A1 (and vice versa) and hence there is no per-link
   LFA for C1A1 and A1C1.

3.3.5.  Conclusion

   All important intra-PoP routes benefit from LFA link and node
   protection with one exception: C1 has no per-prefix LFA to A1.




Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 17]

Internet-Draft      LFA applicability in SP networks        January 2012


   All important inter-PoP routes benefit from LFA link protection.
   They benefit from node protection if e < c.

   Per-link LFA provides the same protection coverage as per-prefix LFA
   with two exceptions.  First, C1A1 has no per-link LFA at all.
   Second, when per-prefix LFA provides node protection (eq2 is
   satisfied), per-link LFA provides effective de facto node protection.

3.3.6.  A square might become a full-mesh

   If the vertical links of the square are made of parallel links (at L3
   or at L2), then one should consider splitting these "vertical links"
   into "vertical and crossed links".  The topology becomes "full-mesh".
   One should also ensure that the two resulting set of links (vertical
   and crossed) do not share any SRLG.

   A typical reason preventing this is that the A1C1 bandwidth may be
   within a building while the A1C2 is between buildings.  Hence while
   from a router port viewpoint the operation is cost-neutral, it is not
   from a cost of bandwidth viewpoint.

3.3.7.  A full-mesh might be more economical than a square

   In a full-mesh, the vertical and cross-links play the dominant role
   as they support most of the primary and backup paths.  The capacity
   of the horizontal links can be dimensioned on the basis of traffic
   destined to a single C or a single A and a single E node.

3.4.  Extended U

   For the Extended U topology, we define the following terminology:

   C1L1: the node "C1" as seen in topology L1.

   C1L2: the node "C1" as seen in topology L2.

   C1LO: the loopback of C1.  This loopback is in L2.

   C2LO: the loopback of C2.  This loopback is in L2.

   Let us also remind that C1 and C2 are L1L2 routers and that their
   loopbacks are in L2 only.









Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 18]

Internet-Draft      LFA applicability in SP networks        January 2012


                                     P
                                    / \
                                  x/   \x+e
                                  /     \
                                 C1<...>C2
                                  |\    | \
                                  | \   |  +-------+
                              d/u |  \  |           \
                                  |   +-|-----+      \
                                  |     |      \      \
                                 A1--a--A2     A3--a--A4
                                  |\    /|      |    /
                               d/u|  \/  |d/u   |  /
                                  | /  \ |      |/
                                  E1     E2     E3

                           Figure 5: Extended U

   There is no L1 link between C1 and C2.  There might be an L2 link
   between C1 and C2.  This is not relevant as this is not seen from the
   viewpoint of the L1 topology which is the focus of our analysis.

   It is guaranteed that there is a path from C1LO to C2LO within the L2
   topology (except if the L2 topology partitions which is very unlikely
   and hence not analyzed here).  We call "c" its path cost.  Once
   again, we assume that c < a.

   We exploit this property to create a tunnel T between C1LO and C2LO.
   Once again, as the source and destination addresses are the loopbacks
   of C1 and C2 and these loopbacks are in L2 only, it is guaranteed
   that the tunnel does not transit via the L1 domain.

   IS-IS does not run over the tunnel and hence the tunnel is not used
   for any primary paths within the L1 or L2 topology.

   Within Level1, we configure C1 (C2) with a Level1 LFA extended
   neighbor "C2 via tunnel T" ("C1 via tunnel T").

   A router supporting such extension learns that it has one additional
   potential neighbor in topology Level1 when checking for LFA's.

   The L1 topology learns about C1LO as an L2=>L1 route with Down bit
   set propagated by C1L1 and C2L1.  The metric advertised by C2L1 is
   bigger than the metric advertised by C1L1 by "c".

   The L1 topology learns about P as an L2=>L1 routes with Down bit set
   propagated by C1L1 and C2L1.  The metric advertised by C2L1 is bigger
   than the metric advertised by C1L1 by "e".  This implies that e <= c.



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 19]

Internet-Draft      LFA applicability in SP networks        January 2012


3.4.1.  E1A1 failure

3.4.1.1.  Per-Prefix LFA

   Five destinations are impacted by E1A1 link failure: A1, C1LO, E2, E3
   and P.

   The LFA for A1 is via A2 because eq1 == a < d + u.  Node protection
   for traffic to A1 upon A1 node failure is not applicable.

   The LFA for E2 is via A2 because eq1 == d < d + u + d.  Node
   protection is guaranteed because eq2 == d < a + d.

   The LFA for E3 is via A2 because eq1 == u + d + d < d + u + d + d.
   Node protection is guaranteed because eq2 == u + d + d < a + u + d +
   d.

   The LFA for C1LO is via A2 because eq1 == u + c < d + u + u.  Node
   protection is guaranteed because eq2 == u + c < a + u.

   If e=0: E1's primary route to P is via ECMP(E1A1, E1A2).  The LFA for
   the first ECMP path (via A1) is the second ECMP path (via A2).  Node
   protection is possible because eq2 == u + x < a + u + x.

   If e<>0: E1's primary route to P is via E1A1.  Its LFA is via A2
   because eq1 == a + c + x < d + u + u + x.  Node protection is
   guaranteed because eq2 == u + x + e < a + u + x <=> e < a.  This is
   true because e <= c and c < a.

   Conclusion: same as the square topology.

3.4.1.2.  Per-Link LFA

   Same as the square topology.

3.4.2.  A1E1 failure

3.4.2.1.  Per-Prefix LFA

   Same as the square topology.

3.4.2.2.  Per-Link LFA

   Same as the square topology.







Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 20]

Internet-Draft      LFA applicability in SP networks        January 2012


3.4.3.  A1C1 failure

3.4.3.1.  Per-Prefix LFA

   Three destinations are impacted when A1C1 fails: C1, E3 and P.

   A1's LFA to C1LO is via A2 because eq1 == u + c < a + u.  Node
   protection property is not applicable for traffic to C1 when C1
   fails.

   A1's LFA to E3 is via A2 because eq1 == u + d + d < d + u + u + d +
   d.  Node protection is guaranteed because eq2 == u + d + d < a + u +
   d + d.

   A1's primary route to P is via C1 (even if e=0, u + x < a + u + x).
   The LFA is via A2 because eq1 == u + x + e < a + u + x <=> e < a
   (which is true see above).  Node protection is guaranteed because eq2
   == u + x + e < a + u + x.

   Conclusion: same as the square topology

3.4.3.2.  Per-Link LFA

   Same as the square topology.

3.4.4.  C1A1 failure

3.4.4.1.  Per-Prefix LFA

   Three destinations are impacted by C1A1 link failure: A1, E1 and E2.
   E2's analysis is the same as E1 and hence is omitted.

   C1L1 has an LFA for A1 via the extended neighbor C2L1 reachable via
   tunnel T. Indeed, eq1 is true: d + a < d + a + u + d.  From the
   viewpoint of C1L1, C2L1's path to C1L1 is C2L1-A2-A1-C1L1.  Remember
   the tunnel is not seen by IS-IS for computing primary paths!  Node
   protection is not applicable for traffic to A1 when A1 fails.

   C1L1's LFA for E1 is via extended neighbor C2L1 (over tunnel T)
   because eq1 == d + d < d + a + u + d + d.  Node protection is
   guaranteed because eq2 == d + d < d + a + d.

3.4.4.2.  Per-Link LFA

   C1 has a per-prefix LFA for destination A1 and hence there is a per-
   link LFA for the link C1A1.  Node resistance is applicable for
   traffic to E1 (and E2).




Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 21]

Internet-Draft      LFA applicability in SP networks        January 2012


3.4.5.  Conclusion

   The extended U topology is as good as the square topology.

   It does not require any cross links between the A and C nodes within
   an aggregation region.  It does not need an L1 link between the C
   routers in an access region.  Note that a link between the C routers
   might exist in the L2 topology.

3.5.  Dual-plane Core and its impact on the Access LFA analysis

   A Dual-plane core is defined as follows
   o  Each access region k is connected to the core by two C routers
      (C(1,k) and C(2,k)).
   o  C(1,k) is part of Plane1 of the dual-plane core.
   o  C(2,k) is part of Plane2 of the dual-plane core.
   o  C(1,k) has a link to C(2, l) iff k = l
   o  {C(1,k) has a link to C(1, l)} iff {C(2,k) has a link to C(2, l)}

   In a dual-plane core design, e = 0 and hence the LFA node-protection
   coverage is improved in all the analyzed topologies.

3.6.  Two-tiered IGP metric allocation

   A Two-tiered IGP metric allocation scheme is defined as follows
   o  all the link metrics used in the L2 domain are part of range R1
   o  all the link metrics used in an L1 domain are part of range R2
   o  range R1 << range R2 such that the difference e = C2P - C1P is
      smaller than any link metric within an access region.

   Assuming such an IGP metric allocation, the following properties are
   guaranteed : c < a, e < c, and e < a.

3.7.  uLoop analysis

   In this section, we analyze a case where the routing transition
   following the failure of a link may have some uLoop potential for one
   destination.  Then we show that all the other cases do not have uLoop
   potential.

   In the square design, upon the failure of link C1A1, traffic
   addressed to A1 can undergo a transient forwarding loop as C1
   reroutes traffic to C2, which initially reaches A1 through C1, as c <
   a.  This loop will actually occur when C1 updates its FIB for
   destination A1 before C2.

   It can be shown that all the other routing transitions following a
   link failure in the analyzed topologies do not have uLoop potential.



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 22]

Internet-Draft      LFA applicability in SP networks        January 2012


   Indeed, in each case, for all destinations affected by the failure,
   the rerouting nodes deviate their traffic directly to adjacent nodes
   whose paths towards these destinations do not change.  As a
   consequence, all these routing transitions cannot undergo transient
   forwarding loops.

   For example, in the square topology, the failure of directed link
   A1C1 does not lead to any uLoop.  The destinations reached over that
   directed link are C1 and P. A1 and E1's shortest paths to these
   destinations after the convergence go via A2.  A2's path to C1 and P
   is not using A1C1 before the failure, hence no uLoop may occur.

3.8.  Summary

   In this section, we summarize the applicability of LFAs detailed in
   the previous sections.  For link protection, we use "Full" to refer
   to the applicability of LFAs for each destination, reached via any
   link of the topology.  For node protection, we use "yes" to refer to
   the fact that node protection is achieved for a given node.
   1.  Intra Area Destinations
          Link Protection
          +  Triangle: Full
          +  Full-Mesh: Full
          +  Square: Full, except C1 has no LFA for dest A1
          +  Extended U: Full
          Node Protection
          +  Triangle: yes.
          +  Full-Mesh: yes.
          +  Square: yes.
          +  Extended U: yes.
   2.  Inter Area Destinations
          Link Protection
          +  Triangle: Full
          +  Full-Mesh: Full
          +  Square: Full
          +  Extended U: Full
          Node Protection
          +  Triangle: yes if e<c
          +  Full-Mesh: yes for A failure, if e<c for C failure
          +  Square: yes for A failure, if e<c for C failure
          +  Extended U : yes if e<= c and c < a
   3.  uLoops
       *  Triangle: None
       *  Full-Mesh: None
       *  Square: None, except traffic to A1 when C1A1 fails
       *  Extended U : None, if a > e





Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 23]

Internet-Draft      LFA applicability in SP networks        January 2012


   4.  Per-Link LFA vs Per-Prefix LFA
       *  Triangle: Same
       *  Full-Mesh: Same
       *  Square: Same except C1A1 has no per-Link LFA.  In practice,
          this means that per-prefix LFAs will be used (hence C1 has no
          LFA for dest=E1 and dest=A1)
       *  Extended U : Same


4.  Core Network

   In the backbone, the optimization of the network design to achieve
   the maximum LFA protection is less straightforward than in the case
   of the access/aggregation network.

   The main optimization objectives for backbone topology design are
   cost, latency, and bandwidth, constrained by the availability of
   fiber.  Optimizing the design for Local IP restoration is more likely
   to be considered as a non-primary objective.  For example, the way
   the fiber is laid out and the resulting cost to change it leads to
   ring topologies in some backbone networks.

   Also, the capacity planning process is already complex in the
   backbone.  It needs to make sure that the traffic matrix (demand) is
   supported by the underlying network (capacity) under all possible
   variation of the underlying network (what-if scenario related to one-
   srlg failure).  Classically, "supported" means that no congestion be
   experienced and that the demands be routed along the appropriate
   latency paths.  Selecting LFA as a deterministic FRR solution for the
   backbone would require to enhance the capacity planning process to
   add a third constraint: each variation of the underlying network
   should lead to a sufficient LFA coverage (we detail this aspect in a
   following section).

   To the contrary, the access network is based on many replications of
   a small number of well-known (well-engineered) topologies.  The LFA
   coverage is deterministic and is independent of additions/insertions
   of a new edge device, a new aggregation sub-region or a new access
   region.

   In practice, we believe that there are three profiles for the
   backbone applicability of LFA.

   In the first profile, the designer plans all the network resilience
   on IGP convergence.  In such case, LFA is a free bonus.  If an LFA is
   available, then the loss of connectivity is likely reduced by a
   factor 10 (50msec vs 500msec), else the loss of connectivity depends
   on IGP convergence which is anyway the initial target.  LFA should be



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 24]

Internet-Draft      LFA applicability in SP networks        January 2012


   very successful here as it provides a significant improvement without
   any additional cost.

   In the second profile, the designer seeks a very high and
   deterministic FRR coverage and he either does not want or cannot
   engineer the topology.  LFA should not be considered in this case.
   MPLS TE FRR would perform much better in this environment.  Explicit
   routing ensures that a backup path exists what-ever the underlying
   topology.

   In the third profile, the designer seeks a very high and
   deterministic FRR coverage and he does engineer the topology.  LFA is
   appealing in this scenario as it can provide a very simple way to
   obtain protection.  Furthermore, in practice, the requirement for FRR
   coverage might be limited to a certain part of the network, given by
   a sub-topology and/or is likely limited to a subset of the demands
   within the traffic matrix.  In such case, if the relevant part of the
   network natively provides a high degree of LFA protection for the
   demands of interest, it might actually be straightforward to improve
   the topology and achieve the level of protection required for the
   sub-topology and demands which matter.  Once again, the practical
   problem needs to be considered (which sub-topology, which real
   demands need 50msec) as it is often simpler than the theoretical
   generic one.

   For the reasons explained previously, the backbone applicability
   should be analyzed on a case by case basis and it is difficult to
   derive generic rules.

   In order to help the reader to assess the LFA applicability in its
   own case, we provide in the next section some simulation results
   based on 11 real backbone topologies.

4.1.  Simulation Framework

   In order to perform an analysis of LFA applicability in the core, we
   usually receive the complete IS-IS/OSPF linkstate database taken on a
   core router.  We parse it to obtain the topology.  During this
   process, we eliminate all nodes connected to the topology with a
   single link and all prefixes except a single "node address" per
   router.  We compute the availability of per-prefix LFA's to all these
   node addresses which we call "destinations" hereafter.  We treat each
   link in each direction.

   For each (directed) link, we compute whether we have a per-prefix LFA
   to the next-hop.  If so, we have a per-link LFA for the link.

   The Per-link-LFA coverage for a topology T is the fraction of the



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 25]

Internet-Draft      LFA applicability in SP networks        January 2012


   number of links with a per-link LFA divided by the total number of
   links.

   For each link, we compute the number of destinations whose primary
   path involves the analyzed link.  For each such destination, we
   compute whether a per-prefix LFA exists.

   The Per-Prefix-LFA coverage for a topology T is the fraction:

   (the sum across all links of the number of destinations with a
   primary path over the link and a per-prefix LFA)

   divided by

   (the sum across all links of the number of destinations with a
   primary path over the link)

4.2.  Data Set

   Our data set is based on 11 SP core topologies with different
   geographical scopes: worldwide, national and regional.  The number of
   nodes range from 600 to 16.  The average link-to-node ratio is 2.3
   with a minimum of 1.2 and maximum of 6.

4.3.  Simulation results

               +----------+--------------+----------------+
               | Topology | Per-link LFA | Per-prefix LFA |
               +----------+--------------+----------------+
               |    T1    |      45%     |       76%      |
               |    T2    |      49%     |       98%      |
               |    T3    |      88%     |       99%      |
               |    T4    |      68%     |       84%      |
               |    T5    |      75%     |       94%      |
               |    T6    |      87%     |       98%      |
               |    T7    |      16%     |       67%      |
               |    T8    |      87%     |       99%      |
               |    T9    |      67%     |       79%      |
               |    T10   |      98%     |       99%      |
               |    T11   |      59%     |       77%      |
               |  Average |      67%     |       89%      |
               |  Median  |      68%     |       94%      |
               +----------+--------------+----------------+

                        Table 1: Core LFA Coverages

   In Table 1, we observe a wide variation in terms of LFA coverage
   across topologies; From 67% to 100% for the per-prefix LFA coverage,



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 26]

Internet-Draft      LFA applicability in SP networks        January 2012


   and from 16% to 98% for the per-link LFA coverage.  Several
   topologies have been optimized for LFAs (T3, 6, 8 and 10).  This
   illustrates the need for case by case analysis when considering LFA
   for core networks.

   It should be noted that, to the contrary of the access/aggregation
   topologies, per-prefix LFA outperforms per-link LFA in the backbone.


5.  Core and Access protection schemes are independent

   Specifically, a design might use LFA FRR in the access and MPLS TE
   FRR in the core.

   LFA provides great benefits for the access network due to its
   excellent access coverage and its simplicity.

   MPLS TE FRR's topology independence might prove beneficial in the
   core when either the LFA FRR coverage is judged too small and/or the
   designer feels unable to optimize the topology to improve the LFA
   coverage.


6.  Simplicity and other LFA benefits

   The LFA solution provides significant benefits which mainly stem from
   its simplicity.

   The LFA behavior is an automated process that makes fast restoration
   an intrinsic part of the IGP, with no additional configuration burden
   in the IGP or any other protocol.

   Thanks to this integration, the use of multiple areas in the IGP does
   not make Fast Restoration more complex to achieve than in a single
   area IGP design.

   There is no requirement for network-wide upgrade as LFAs do not
   require any protocol change and hence can be deployed router by
   router.

   With LFAs, the backup paths are pre-computed and installed in the
   dataplane in advance of the failure.  Assuming a fast enough FIB
   update time compared to the total number of (important) destinations,
   a "<50msec repair" requirement becomes achievable.  With a prefix-
   independent implementation, LFAs have a fixed repair time, as it only
   depends on the failure detection time and the time to activate the
   LFA behavior, which does not scale with the number of destinations to
   be fast rerouted.



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 27]

Internet-Draft      LFA applicability in SP networks        January 2012


   Link and node protection are provided together and without
   operational difference (as a comparison, MPLS TE FRR link and node
   protections require different types of backup tunnels and different
   grades of operational complexity).

   Also, compared to MPLS TE FRR, an important simplicity aspect of LFA
   is that is does not require the introduction of yet another virtual
   layer of topology.  Maintaining a virtual topology of explicit MPLS
   TE tunnels clearly increases the complexity of the network.  MPLS TE
   tunnels would have to be represented in a network management system
   in order to be monitored and managed.  In large networks this may
   significantly contribute to the number of network entities polled by
   the network management system and monitored by operational staff.
   LFA on the other hand only has to be monitored for its operational
   status once per router and it needs to be considered in the network
   planning process.  If the latter is done based on offline simulations
   for failure cases anyways, the incremental cost of supporting LFA for
   a defined set of demands may be relatively low.

   The per-prefix mode of LFAs allows for a simpler and more efficient
   capacity planning.  As the backup path of each destination is
   optimized individually, the load to be fast rerouted can be spread on
   a set of shortest-repair-paths (as opposed to one single backup
   tunnel).  This leads for a simpler and more efficient capacity
   planning process that takes congestion during protection into
   account.


7.  Capacity Planning with LFA in mind

   We briefly describe the functionality a designer should expect from a
   capacity planning tool supporting LFA and the related capacity
   planning process.

7.1.  Coverage Estimation - Default Topology

   Per-Link LFA Coverage Estimation: the tool would color each
   unidirectional link in depending on whether per-link LFA is available
   or not.  Per-Prefix LFA Coverage Estimation: the tool would color
   each unidirectional link with a colored gradient based on the % of
   destinations which have a per-prefix LFA.

   On top of the visual GUI reporting, the tool should provide detailed
   tables listing, on a per interface basis: percentage of LFA, number
   of prefixes with LFA, number without LFA, list of prefixes without
   LFA.

   Furthermore, the tool should provide the percentage and list the



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 28]

Internet-Draft      LFA applicability in SP networks        January 2012


   traffic matrix demands with less than 100% source-to-destination LFA
   coverage, and, average coverage (#links this demand has an LFA on/#
   links this demands traverses) for every demands (using a threshold).

   The user should be able to alter the color scheme to show whether
   these LFAs are guaranteed-node-protecting or de-facto node protecting
   or only link protecting.

   This functionality provides the same level of information as we
   described in sections 4.1 to 4.3.

7.2.  Coverage estimation in relation to traffic

   Instead of reporting the coverage as a ratio of the number of
   destinations with a backup, one might prefer a ratio of the amount of
   traffic on a link that benefits from protection.

   This is likely much more relevant as not all destinations are equal
   and it is much more important to have an LFA for a destination
   attracting lots of traffic rather than an unpopular destination.

7.3.  Coverage verification for a given set of demands

   Depending on the requirements on the network it might be more
   relevant to verify the complete LFA coverage of a given sub-topology,
   or a given set of demands, rather than calculating the relative
   coverage of the overall traffic.  This is most likely true for the
   third engineering profile described in Section 4.

   In that case, the tool should be able to separately report the LFA
   coverage on a given set of demands and highlight each part of the
   network that does not support 100% coverage for any of those demands.

7.4.  Modeling - What-if Scenarios - Coverage impact

   The tool should be able to compute the coverage for all the possible
   topologies that result from a set of expected failures (ie. one-srlg
   failure).

   Filtering the key information from the huge amount of generated data
   should be a key property of the tool.

   For example, the user could set a threshold (at least 80% per-prefix
   LFA coverage in all one-srlg what-if scenarios) and the tool would
   report only the cases where this condition is not met, hopefully with
   some assistance on how to remedy the problem (IGP metric
   optimization).




Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 29]

Internet-Draft      LFA applicability in SP networks        January 2012


   As an application example, a designer who is not able to ensure c < a
   could leverage such a tool to assess the per-prefix LFA coverage for
   square aggregation topologies grafted to its core backbone topology.
   The tool would analyze the per-prefix LFA availability for each
   remote destination and would help optimize the backbone topology to
   increase the LFA protection coverage for failures within the square
   aggregation topologies.

7.5.  Modeling - What-if Scenarios - Load impact

   The tool should be able to compute the link load for all routing
   states that result from a set of expected failures (i.e. one-srlg
   failure).

   The routing states that should be supported are: 1/ network-wide
   converged state before the failure, 2/ all the LFA's protecting the
   failure are active and 3/ network-wide converged state after the
   failure.

   Filtering the key information from the huge amount of generated data
   should be a key property of the tool.

   For example, the user could set a threshold (at most 100% link load
   in all one-srlg what-if scenarios) and the tool would report only the
   cases where this condition is violated, hopefully with some
   assistance on how to remedy the problem (IGP metric optimization).

   The tool should be able to do this for the aggregate load and as well
   on a per class of service basis.

   Note: in case the traffic matrix is unknown, an intermediate solution
   consists in identifying the destinations that would attract traffic
   (i.e.  PE routers), and those that would not (i.e.  P routers).  You
   could achieve this by creating a traffic matrix with equal demands
   between the sources/destinations that would attract traffic (Pe to
   PE).  This will be more relevant than considering all demands between
   all prefixes (e.g. when there is no customer traffic from P to P).

7.6.  Discussion on metric recommendations

   While LFA FRR has many benefits (section 6), LFA FRR's applicability
   depends on topology.

   The purpose of this document is to show how to introduce a level of
   control on this topology parameter.

   On the one hand, we wanted to show that by adopting a small set of
   igp metric constraints and a repetition of well-behaved patterns, the



Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 30]

Internet-Draft      LFA applicability in SP networks        January 2012


   designer could deterministically guarantee maximum link and node
   protection for the vast majority of the network (the access/
   aggregation).  Doing so, he would obtain an extremely simple
   resiliency solution.

   One another side, we also wanted to show that it might not be so bad
   to not apply (all) these constraints.

   Indeed, we showed in section 3.3.4.3 that the per-prefix LFA coverage
   in a square where c > a might still be very good.

   We showed in section 4.3 that the median per-prefix LFA coverage for
   11 SP backbone topologies still provides for 94% coverage (most of
   these topologies were built without any idea of LFA)!

   Furthermore, we showed that any topology may be analyzed with an LFA-
   aware capacity planning tool.  This would readily assess the coverage
   of per-prefix LFA and would assist the designer in fine-tuning it to
   obtain the level of protection he seeks.

   While this document highlighted LFA applicability and benefits for SP
   network, it also noted that LFA is not meant to replace MPLS TE FRR.

   With a very-LFA-unfriendly topology, a designer seeking a guaranteed
   < 50msec protection might be better off leveraging the explicit-
   routed backup capability of MPLS TE FRR to provide 100% protection
   while ensuring no congestion along the backup paths during
   protection.

   But when LFA provides 100% link and node protection without any
   uLoop, then clearly LFA seems a technology to consider to drastically
   simplify the operation of a large-scale network.


8.  Security Considerations

   The security considerations applicable to LFAs are described in
   [RFC5286].  This document does not introduce any new security
   considerations.


9.  IANA considerations

   This draft does not require any IANA considerations.







Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 31]

Internet-Draft      LFA applicability in SP networks        January 2012


10.  Conclusions

   LFA is an important protection alternative for IP/MPLS networks.

   Its simplicity benefit is significant, in terms of automation and
   integration with the default IGP behavior and the absence of any
   requirement for network-wide upgrade.  The technology does not
   require any protocol change and hence can be deployed router by
   router.

   At first sight, these significant simplicity benefits are negated by
   the topological dependency of its applicability.

   The purpose of this document was to highlight that very frequent
   access and aggregation topologies benefit from excellent link and
   node LFA coverage.

   A second objective consisted in describing the three different
   profiles of LFA applicability for the IP/MPLS core networks and
   illustrating them with simulation results based on real SP core
   topologies.


11.  Contributors

   This work has been realized in tight collaboration with the following
   people.

         Mike Shand
         imc.shand@googlemail.com

         Bruno Decraene
         France Telecom
         38-40 rue du General Leclerc
         92794 Issy Moulineaux cedex 9
         FR
         bruno.decraene@orange.com

         James Uttaro
         ATT
         200 S. Laurel Avenue
         07748, Middletown, NJ
         US
         uttaro@att.com

         Nicolai Leymann





Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 32]

Internet-Draft      LFA applicability in SP networks        January 2012


         Deutsche Telekom
         Winterfeldtstrasse 21
         10781, Berlin
         DE
         N.Leymann@telekom.de

         Martin Horneffer
         Deutsche Telekom
         Hammer Str. 216-226
         48153, Muenster
         DE
         Martin.Horneffer@telekom.de


12.  Acknowledgments

   We would like to thank Alvaro Retana and Stewart Bryant (in bold) for
   their precious comments on this work.


13.  References

13.1.  Normative References

   [RFC5286]  Atlas, A. and A. Zinin, "Basic Specification for IP Fast
              Reroute: Loop-Free Alternates", RFC 5286, September 2008.

13.2.  Informative References

   [RFC5714]  Shand, M. and S. Bryant, "IP Fast Reroute Framework",
              RFC 5714, January 2010.

   [RFC1195]  Callon, R., "Use of OSI IS-IS for routing in TCP/IP and
              dual environments", RFC 1195, December 1990.

   [RFC2328]  Moy, J., "OSPF Version 2", RFC 2328, April 1998.

   [RFC5340]  Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
              for IPv6", RFC 5340, July 2008.












Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 33]

Internet-Draft      LFA applicability in SP networks        January 2012


Authors' Addresses

   Clarence Filsfils
   Cisco Systems
   Brussels  1000
   BE

   Email: cf@cisco.com


   Pierre Francois
   Institute IMDEA Networks
   Avda. del Mar Mediterraneo, 22
   Leganese  28918
   ES

   Email: pierre.francois@imdea.org


































Clarence Filsfils & Pierre Francois  Expires July 21, 2012     [Page 34]