Internet-Draft K. Yamamoto (NAIST) K. Cho (Sony CSL) Expires in six months Y. Inoue (Fujitsu) H. Esaki (Toshiba) Y. Atarashi (Hitachi) A. Hagiwara (Bay Networks) September, 1997 IPv6 over Point-to-Point ATM Link Status of this Memo This document is an Internet-Draft. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as ``work in progress.'' To learn the current status of any Internet-Draft, please check the ``1id-abstracts.txt'' listing contained in the Internet-Drafts Shadow Directories on ds.internic.net (US East Coast), nic.nordu.net (Europe), ftp.isi.edu (US West Coast), or munnari.oz.au (Pacific Rim). Abstract This memo defines a communication mechanism to exchange both IPv6 unicast and multicast packets over an ATM network used as a point-to-point link. 1. Introduction ATM is now one of the most popular link-layer technologies in the Internet. Typical usage of ATM is categorized as follows: (1) Broadcast network such as LAN emulation(LANE) (2) Non-Broadcast Multiple Access(NBMA) networks (3) Point-to-point networks This memo discusses a communication mechanism for an IPv6[IPV6] over a point-to-point ATM link(3). One of applications of ATM is a fat pipe typically found in backbone networks. This memo defines IEEE 802.2 logical link control(LLC) headers for IPv6 over a point-to-point ATM link. The default of MTU size of point-to-point ATM and a mechanism to generate an interface identifier are also specified. YAMAMOTO [Page 1] Internet Draft IPv6 over ATM September 1997 2. Scope of This Memo Throughout this memo, the term "point-to-point ATM link" means that one virtual circuit(VC) is established between two nodes and the VC can be accessible through one logical network interface. This link is abstracted as a serial link to IPv6. It is not our intention to recommend that ATM be used exclusively for point-to-point networks. In this memo, ATM Adaptation Layer 5(AAL5)[ATM-ENCAP] is assumed to carry IPv6 packets over ATM. Both IPv6 unicast and multicast packets are delivered only to the opposite end of the point-to-point ATM link. Please note that point-to-point ATM link here is not a special case of NBMA(2). While NBMA requires a special mechanism for multicast, a point-to-point ATM link here does not require it. There is strong demand to implement an IPv6 network over a point-to-point ATM link without such a special mechanism. So, it is highly desirable to define LLC headers of IPv6 over a point-to-point ATM link for inter-operability. 3. Standard Keywords This memo uses terms which are in capital letters. When the terms "MUST", "SHOULD", "MUST NOT", "SHOULD NOT", and "MAY" appear capitalized, they are being used to indicate particular requirements, whose definitions are found in [KEYWORDS]. 4. IPv6 packet encapsulation LLC encapsulation SHOULD be used to exchange IPv6 packets over a point-to-point ATM link. Null encapsulation SHOULD NOT be used for IPv6 packets since it is very likely that both IPv6 and IPv4 are used on a point-to-point ATM link at the same time. 0x86DD is assigned for the EtherType of IPv6[ETHER], so this memo chooses 0x86DD as the Protocol Identifier(PID) according to [ATM-ENCAP]. The encapsulation for both IPv6 unicast and multicast on a point-to-point ATM link is defined as follows: +-------------------------------+ | LLC 0xAA-AA-03 | +-------------------------------+ | OUI 0x00-00-00 | +-------------------------------+ | PID 0x86-DD | +-------------------------------+ | . | | IPv6 packet | | . | +-------------------------------+ YAMAMOTO [Page 2] Internet Draft IPv6 over ATM September 1997 5. MTU size The default MTU size for IPv6 over point-to-point ATM SHOULD be 9180 octets according to [AAL5-MTU]. Values other than the default MAY be used. An automatic negotiation mechanism for the MTU is not defined in this memo. It is not usually necessary on ATM point-to-point links as long as same MTU value is correctly configured for each end of nodes and if Path MTU Discovery is used for off link communication. However, it is useful to provide a manual configuration mechanism of MTU in certain cases. For example, consider that a host and a router are connected with a point-to-point ATM link and the router is also attached to a LAN whose MTU is smaller than 9180. To prevent Path MTU Discovery triggered by the host, an administrator may wish to configure the MTU of the ATM interface to the smaller one in the router. This value will be announced to the host via Router Advertisements(RA) through the point-to-point ATM link then the host will adjust its MTU for the link. 6. Interface Identifier An interface for a point-to-point ATM link MUST have a 64 bit interface token for IPv6. It MUST be unique within the link. The interface token SHOULD be generated according to the following steps: (A) If the ATM interface has an EUI 64 bit MAC address, generate an interface identifier with it according to "Links or Nodes with EUI-64 Identifiers" in Appendix A of [AARCH]. (B) If the ATM interface has an IEEE 802 48 bit MAC adddress, generate an interface identifier with it according to "Links or Nodes with IEEE 802 48 bit MAC's" in Appendix A of [AARCH]. Note: A node may have multiple virtual interfaces on a single physical ATM interface. Such a node may generate the same interface identifier for the virtual interfaces, however, it is not a problem since interface identifier is not necessarily unique on the node. (C) If an EUI 64 bit MAC address is available anywhere on the node, generate an interface identifier with it according to "Links or Nodes with EUI-64 Identifiers" in Appendix A of [AARCH]. (D) If an IEEE 802 48 bit MAC adddress is available anywhere on the node, generate an interface identifier with it according to "Links or Nodes with IEEE 802 48 bit MAC's" in Appendix A of [AARCH]. (E) If an IEEE global identifier is not available, a different source of uniqueness should be used. For example, a suggested source of uniqueness is machine serial numbers. If such a source is available, generate an interface identifier with it according YAMAMOTO [Page 3] Internet Draft IPv6 over ATM September 1997 to "Links with Non-Global Identifiers" in Appendix A of [AARCH]. (F) If a good source of uniqueness cannot be found, generate an interface identifier with a random number according to "Links with Non-Global Identifiers" in Appendix A of [AARCH]. 7. Neighbor Discovery It is required to implement NDP[NDP] functions on a typical point-to-point link defined in [NDPP2P]. 8. Relationship with PPP This memo is one of the current simple solutions. PPP[PPP] is a more advanced solution with more features and subsequently needs more resources. Currently, the only feature provided by PPP which is not covered by this memo is Maximum Receive Unit (MRU). Duplicated Token Discovery is possible by Duplicated Address Detection. This memo provides an enough mechanism for current several well-managed and relatively static ATM environments. IPv6 over PPP over point-to-point ATM link may be used in the future if less-managed and/or more dynamic IPv6 on ATM circumstances are needed and/or more useful configuration options are defined for it. 9. Security Consideration It is believed that this memo does not introduce new security problems to IPv6. References [AAL5-MTU] R. Atkinson, "Default IP MTU for use over ATM AAL5", RFC 1626, 1994. [AARCH] R. Hinden and S. Deering "IP Version 6 Addressing Architecture", Internet-Draft, , 1997. [ATM-ENCAP] J. Heinanen, "Multiprotocol Encapsulation over ATM Adaptation Layer 5", RFC1483, 1993. [ETHER] M. Crawford, "Transmission of IPv6 Packets over Ethernet Networks", currently draft-ietf-ipngwg-trans-ethernet-02.txt. [EUI64] "64-Bit Global Identifier Format Tutorial", http://standards.ieee.org/db/oui/tutorials/EUI64.html. [IPV6] S. Deering and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 1883, 1996. [KEYWORDS] S. Bradner, "Key words for use in RFCs to Indicate Requirement Levels", RFC 2119, March 1997. YAMAMOTO [Page 4] Internet Draft IPv6 over ATM September 1997 [NDP] T. Narten, E. Nordmark, and W. Simpson, "Neighbor Discovery for IP Version 6 (IPv6)", Internet-Draft, , 1997. [NDPP2P] Preparing. [PPP] Dimitry Haskin and Ed Allen, "IP Version 6 over PPP", Internet-Draft, , 1997. Author's Address Kazuhiko YAMAMOTO Graduate School of Information Science Nara Institute of Science and Technology(NAIST) 8916-5 Takayama, Ikoma 630-01 JAPAN Phone: +81-743-72-5111 FAX: +81-743-72-5329 EMail: Kazu@Mew.org Kenjiro CHO Sony Computer Science Laboratory Inc. 3-14-13 Higashi-Gotanda, Shinagawa-ku 141 JAPAN Phone: +81-3-5448-4380 FAX: +81-3-5448-4273 EMail: kjc@csl.sony.co.jp Yoshinobu INOUE Fujitsu Limited 4-1-1 Kamikodanaka, Nakahara-ku, Kawasaki 211-88 JAPAN Phone: +81-44-754-3263 FAX: +81-44-754-3864 EMail: shin@nd.net.fujitsu.co.jp Hiroshi ESAKI Computer and Network Product Division, Toshiba Corporation Suite 19A, 1-1-1 Shibaura, Minato-ku 105-01 JAPAN Phone: +81-3-3457-2563 FAX: +81-3-5444-9331 EMail: hiroshi@isl.rdc.toshiba.co.jp Yoshifumi ATARASHI Office Systems Division, Hitachi, Ltd. 810 Shimoimaizumi, Ebina-shi 243-04 JAPAN Phone: +81-462-35-2111 FAX: +81-462-35-8325 EMail: atarashi@ebina.hitachi.co.jp Atsushi HAGIWARA Bay Networks K.K. YAMAMOTO [Page 5] Internet Draft IPv6 over ATM September 1997 28th SHIROYAMA JT MORI BLDG. 4-3-1, Torano-mon, Minato-ku 105 JAPAN Phone: +81-3-5402-7001 FAX: +81-3-5402-0179 EMail: ahagiwar@baynetworks.co.jp YAMAMOTO [Page 6] ----