TSGWG J. Touch Internet Draft USC/ISI Intended status: Experimental January 3, 2017 Expires: July 2017 Transport Options for UDP draft-touch-tsvwg-udp-options-04.txt Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. This document may not be modified, and derivative works of it may not be created, and it may not be published except as an Internet-Draft. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html This Internet-Draft will expire on February 3, 2017. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Touch Expires July 3, 2017 [Page 1] Internet-Draft Transport Options for UDP January 2017 Abstract Transport protocols are extended through the use of transport header options. This document experimentally extends UDP to provide a location, syntax, and semantics for transport layer options. Table of Contents 1. Introduction...................................................2 2. Conventions used in this document..............................2 3. Background.....................................................3 4. The UDP Option Area............................................3 5. UDP Options....................................................6 5.1. End of Options List (EOL).................................7 5.2. No Operation (NOP)........................................7 5.3. Option Checksum (OCS).....................................8 5.4. Alternate Checksum (ACS)..................................8 5.5. Lite (LITE)...............................................9 5.6. Experimental (EXP).......................................11 6. Whose options are these?......................................11 7. UDP options vs. UDP-Lite......................................12 8. Interactions with Legacy Devices..............................12 9. Options in a Stateless, Unreliable Transport Protocol.........13 10. Security Considerations......................................14 11. IANA Considerations..........................................14 12. References...................................................14 12.1. Normative References....................................14 12.2. Informative References..................................14 13. Acknowledgments..............................................15 1. Introduction Transport protocols use options as a way to extend their capabilities. TCP [RFC793], SCTP [RFC4960], and DCCP [RFC4340] include space for these options but UDP [RFC768] currently does not. This document defines an experimental extension to UDP that provides space for transport options including their generic syntax and semantics for their use in UDP's stateless, unreliable message protocol. 2. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Touch Expires July 3, 2017 [Page 2] Internet-Draft Transport Options for UDP January 2017 In this document, these words will appear with that interpretation only when in ALL CAPS. Lowercase uses of these words are not to be interpreted as carrying significance described in RFC 2119. In this document, the characters ">>" preceding an indented line(s) indicates a statement using the key words listed above. This convention aids reviewers in quickly identifying or finding the portions of this RFC covered by these key words. 3. Background Many protocols include a default header and an area for header options. These options enable the protocol to be extended for use in particular environments or in ways unforeseen by the original designers. Examples include TCP's Maximum Segment Size, Window Scale, Timestamp, and Authentication Options [RFC793][RFC5925][RFC7323]. These options are used both in stateful (connection-oriented, e.g., TCP [RFC793], SCTP [RFC4960], DCCP [RFC4340]) and stateless (connectionless, e.g., IPv4 [RFC791], IPv6 [RFC2460] protocols. In stateful protocols they can help extend the way in which state is managed. In stateless protocols their effect is often limited to individual packets, but they can have an aggregate effect on a sequence as well. One example of such uses is Substrate Protocol for User Datagrams (SPUD) [Tr15], and this document is intended to provide an out-of-band option area as an alternative to the in-band mechanism currently proposed [Hi15]. UDP is one of the most popular protocols that lacks space for options [RFC768]. The UDP header was intended to be a minimal addition to IP, providing only ports and a data checksum for protection. This document experimentally extends UDP to provide a trailer area for options located after the UDP data payload. 4. The UDP Option Area The UDP transport header includes demultiplexing and service identification (port numbers), a checksum, and a field that indicates the UDP datagram length (including UDP header). The UDP Length length field is typically redundant with the size of the maximum space available as a transport protocol payload (see also discussion in Section 8). For IPv4, IP Total Length field indicates the total IP datagram length (including IP header), and the size of the IP options is indicated in the IP header (in 4-byte words) as the "Internet Header Touch Expires July 3, 2017 [Page 3] Internet-Draft Transport Options for UDP January 2017 Length" (IHL), as shown in Figure 1 [RFC791]. As a result, the typical (and largest valid) value for UDP Length is: UDP_Length = IPv4_Total_Length - IPv4_IHL * 4 For IPv6, the IP Payload Length field indicates the datagram after the base IPv6 header, which includes the IPv6 extension headers and space available for the transport protocol, as shown in Figure 2 [RFC2460]. Note that the Next HDR field in IPv6 might not indicate UDP (i.e., 17), e.g., when intervening IP extension headers are present. For IPv6, the lengths of any additional IP extensions are indicated within each extension [RFC2460], so the typical (and largest valid) value for UDP Length is: UDP_Length = IPv6_Payload_Length - sum(extension header lengths) In both cases, the space available for the UDP transport protocol data unit is indicated by IP, either completely in the base header (for IPv4) or adding information in the extensions (for IPv6). In either case, this document will refer to this available space as the "IP transport payload". +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Version| IHL |Type of Service| Total Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Identification |Flags| Fragment Offset | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Time to Live | Proto=17 (UDP)| Header Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Source Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... zero or more IP Options (using space as indicated by IHL) ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Source Port | UDP Destination Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Length | UDP Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1 IPv4 datagram with UDP transport payload Touch Expires July 3, 2017 [Page 4] Internet-Draft Transport Options for UDP January 2017 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |Version| Traffic Class | Flow Label | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Payload Length | Next Hdr | Hop Limit | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... | Source Address (128 bits) | ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... | Destination Address (128 bits) | ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ... zero or more IP Extension headers (each indicating size) ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Source Port | UDP Destination Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | UDP Length | UDP Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2 IPv6 datagram with UDP transport payload As a result of this redundancy, there is an opportunity to use the UDP Length field as a way to break up the IP transport payload into two areas - that intended as UDP user data and an additional "surplus area" (as shown in Figure 3). IP transport payload <-------------------------------------------------> +--------+---------+----------------------+------------------+ | IP Hdr | UDP Hdr | UDP user data | surplus area | +--------+---------+----------------------+------------------+ <------------------------------> UDP Length Figure 3 IP transport payload vs. UDP Length In most cases, the IP transport payload and UDP Length point to the same location, indicating that there is no surplus area. It is important to note that this is not a requirement of UDP [RFC768] (discussed further in Section 8). UDP-Lite used the difference in these pointers to indicate the partial coverage of the UDP Checksum, such that the UDP user data, UDP header, and UDP pseudoheader (a subset of the IP header) are covered by the UDP checksum but additional user data in the surplus area is not covered [RFC3828]. This document uses the surplus area for UDP transport options. Touch Expires July 3, 2017 [Page 5] Internet-Draft Transport Options for UDP January 2017 The UDP option area is thus defined as the location between the end of the UDP payload and the end of the IP datagram as a trailing options area. This area can occur at any valid byte offset, i.e., it need not be 16-bit or 32-bit aligned. In effect, this document redefines the UDP "Length" field as a "trailer offset". UDP options are defined using a syntax similar to that of TCP [RFC793]. They are typically a minimum of two bytes in length as shown in Figure 4, excepting only the one byte options "No Operation" (NOP) and "End of Options List" (EOL) described below. +--------+--------+ | Kind | Length | +--------+--------+ Figure 4 UDP option default format >> UDP options MAY occur at any UDP length offset. >> The UDP length MUST be at least as large as the UDP header (8) and no larger than the IP transport payload. Values outside this range MUST be silently discarded as invalid and logged where rate- limiting permits. Others have considered using values of the UDP Length that is larger than the IP transport payload as an additional type of signal. Using a value smaller than the IP transport payload is expected to be backward compatible with existing UDP implementations, i.e., to deliver the UDP Length of user data to the application and silently ignore the additional surplus area data. Using a value larger than the IP transport payload would either be considered malformed (and be silently dropped) or could cause buffer overruns, and so is not considered silently and safely backward compatible. Its use is thus out of scope for the extension described in this document. >> UDP options MUST be interpreted in the order in which they occur in the UDP option area. 5. UDP Options The following UDP options are currently defined: Touch Expires July 3, 2017 [Page 6] Internet-Draft Transport Options for UDP January 2017 Kind Length Meaning ---------------------------------------------- 0 - End of Options List (EOL) 1 - No operation (NOP) 2 2 Option checksum (OCS) 3 4 Alternate checksum (ACS) 4 4 Lite (LITE) 128-253 RESERVED 254 N(>=4) RFC 3692-style experiments (EXP) 255 RESERVED These options are defined in the following subsections. 5.1. End of Options List (EOL) The End of Options List (EOL) option indicates that there are no more options. It is used to indicate the end of the list of options without needing to pad the options to fill all available option space. +--------+ | Kind=0 | +--------+ Figure 5 UDP EOL option format >> When the UDP options do not consume the entire option area, the last non-NOP option SHOULD be EOL (vs. filling the entire option area with NOP values). >> All bytes after EOL MUST be ignored by UDP option processing. 5.2. No Operation (NOP) The No Operation (NOP) option is a one byte placeholder, intended to be used as padding, e.g., to align multi-byte options along 16-bit or 32-bit boundaries. +--------+ | Kind=1 | +--------+ Figure 6 UDP NOP option format >> If options longer than one byte are used, NOP options SHOULD be used at the beginning of the UDP options area to achieve alignment as would be more efficient for active (i.e., non-NOP) options. Touch Expires July 3, 2017 [Page 7] Internet-Draft Transport Options for UDP January 2017 5.3. Option Checksum (OCS) The Option Checksum (OCS, Kind = 2) is an 8-bit ones-complement sum (Ones8) that covers only the UDP options, from the first option as indicated by the UDP Length to the last option as indicated by EOL (where present) or the IP Payload Length. OCS can be calculated by computing the 16-bit ones-complement sum and "folding over" the result (using carry wraparound). Note that OCS is direct, i.e., it is not negated or adjusted if zero (unlike the Internet checksum as used in IPv4, TCP, and UDP headers). OCS protects the option area from errors in a similar way that the UDP checksum protects the UDP user data. +--------+--------+ | Kind=2 | Ones8 | +--------+--------+ Figure 7 UDP OCS option format >> When present, the option checksum SHOULD occur as early as possible, preferably preceded by only NOP options for alignment and the LITE option if present. >> If the option checksum fails, all options MUST be ignored and any trailing surplus data silently discarded. >> UDP data that is validated by a correct UDP checksum MUST be delivered to the application layer, even if the UDP option checksum fails, unless the endpoints have negotiated otherwise for this segment's socket pair. 5.4. Alternate Checksum (ACS) The Alternate Checksum (ACS) is a CRC16 of the UDP payload only. It does not include the IP pseudoheader or UDP header, and so need not be updated by NATs when IP addresses or UDP ports are rewritten. Its purpose is to detect errors that the UDP checksum might not detect. +--------+--------+--------+--------+ | Kind=3 | Len=4 | CRC16sum | +--------+--------+-----------------+ Figure 8 UDP ACS option format Touch Expires July 3, 2017 [Page 8] Internet-Draft Transport Options for UDP January 2017 5.5. Lite (LITE) The Lite option is intended to provide equivalent capability to the UDP Lite transport protocol [RFC3828]. UDP Lite allows the UDP checksum to cover only a prefix of the UDP data payload, to protect critical information (e.g., application headers) but allow potentially erroneous data to be passed to the user. This feature helps protect application headers but allows for application data errors. Some applications are impacted more by a lack of data than errors in data, e.g., voice and video. >> When the Lite option is active, it MUST come first in the UDP options list. The Lite option is intended to support the same API as for UDP Lite to allow applications to send and receive data that has a marker indicating the portion protected by the UDP checksum and the portion not protected by the UDP checksum. The option includes a 2-byte offset that indicates the length of the portion of the UDP data that is not covered by the UDP checksum. +--------+--------+--------+--------+ | Kind=4 | Len=4 | Offset | +--------+--------+-----------------+ Figure 9 UDP LITE option format At the sender, the option is formed using the following steps: 1. Create a LITE option, ordered as the first UDP option (Figure 10). 2. Calculate the location of the start of the options as an absolute offset from the start of the UDP header and place that length in the last two bytes of the LITE option. 3. Swap all four bytes of the LITE option with the first 4 bytes of the LITE data area (Figure 11). Touch Expires July 3, 2017 [Page 9] Internet-Draft Transport Options for UDP January 2017 +---------+--------------+--------------+------------------+ | UDP Hdr | user data | Lite data |LITE| other opts | +---------+--------------+--------------+------------------+ <----------------------> UDP Length Figure 10 Lite option formation - LITE goes first +---------+--------------+--------------+------------------+ | UDP Hdr | user data | Lite data |LITE| other opts | +---------+--------------+--------------+------------------+ ^^^^ ^^^^ | | +--------------+ Figure 11 Lite option before transmission - swap LITE and front of LITE data The resulting packet has the format shown in Figure 12. Note that the UDP length now points to the LITE option, and the LITE option points to the start of the option area. +---------+--------------+----------------+------------------+ | UDP Hdr | user data |LITE| Lite data |Ldat| other opts | +---------+--------------+----------------+------------------+ <----------------------> | ^ UDP Length +-------------+ Figure 12 Lite option as transmitted A legacy endpoint receiving this packet will discard the LITE option and everything that follows, including the lite data and remainder of the UDP options. The UDP checksum will protect only the user data, not the LITE option or lite data. Receiving endpoints capable of processing UDP options will do the following: 1. Process options as usual. This will start at the LITE option. 2. When the LITE option is encountered, record its location as the start of the LITE data area and swap the four bytes there with the four bytes at the location indicated inside the LITE option, which indicates the start of all of the options, including the LITE one (one past the end of the lite data area). Touch Expires July 3, 2017 [Page 10] Internet-Draft Transport Options for UDP January 2017 3. Continue processing the remainder of the options, which are now in the format shown in Figure 11. The purpose of this swap is to support UDP Lite operation and UDP options without requiring the entire lite data area to be moved after the UDP option area. 5.6. Experimental (EXP) The Experimental option (EXP) is reserved for experiments [RFC3692]. Only one such value is reserved because experiments are expected to use an Experimental ID (ExIDs) to differentiate concurrent use for different purposes, using UDP ExIDs registered with IANA according to the approach developed for TCP experimental options [RFC6994]. >> The length of the experimental option MUST be at least 4 to account for the Kind, Length, and the minimum 16-bit UDP ExID identifier (similar to TCP ExIDs [RFC6994]). 6. Whose options are these? UDP options are indicated in an area of the IP payload that is not used by UDP. That area is really part of the IP payload, not the UDP payload, and as such, it might be tempting to consider whether this is a generally useful approach to extending IP. Unfortunately, the surplus area exists only for transports that include their own transport layer payload length indicator. TCP and SCTP include header length fields that already provide space for transport options by indicating the total length of the header area, such that the entire remaining area indicated in the network layer (IP) is transport payload. UDP-Lite already uses the UDP Length field to indicate the boundary between data covered by the transport checksum and data not covered, and so there is no remaining area where the length of the UDP-Lite payload as a whole can be indicated [RFC3828]. >> UDP options are intended for use only by the transport endpoints. They are no more (or less) appropriate to be modified in-transit than any other portion of the transport datagram. UDP options are are transport options. Generally, transport datagrams are not intended to be modified in-transit. However, the UDP option mechanism provides no specific protection against in- transit modification of the UDP header, UDP payload, or UDP option area. Touch Expires July 3, 2017 [Page 11] Internet-Draft Transport Options for UDP January 2017 7. UDP options vs. UDP-Lite UDP-Lite provides partial checksum coverage, so that packets with errors in some locations can be delivered to the user [RFC3828]. It uses a different transport protocol number (136) than UDP (17) to interpret the UDP Length field as the prefix covered by the UDP checksum. UDP (protocol 17) already defines the UDP Length field as the limit of the UDP checksum, but by default also limits the data provided to the application as that which precedes the UDP Length. A goal of UDP-Lite is to deliver data beyond UDP Length as a default, which is why a separate transport protocol number was required. UDP options do not need a separate transport protocol number because the data beyond the UDP Length offset (surplus data) is not provided to the application by default. That data is interpreted exclusively within the UDP transport layer. UDP options support a similar service to UDP-Lite by terminating the UDP options with an EOL option. The additional data not covered by the UDP checksum follows that EOL option, and is passed to the user separately. The difference is that UDP-Lite provides the un- checksummed user data to the application by default, whereas UDP options can provide the same capability only for endpoints that are negotiated in advance (i.e., by default, UDP options would silently discard this non-checksummed data). Additionally, in UDP-Lite the checksummed and non-checksummed payload components are adjacent, whereas in UDP options they are separated by the option area - which, minimally, must consist of at least one EOL option. UDP-Lite cannot support UDP options, either as proposed here or in any other form, because the entire payload of the UDP packet is already defined as user data and there is no additional field in which to indicate a separate area for options. The UDP Length field in UDP-Lite is already used to indicate the boundary between user data covered by the checksum and user data not covered. 8. Interactions with Legacy Devices It has always been permissible for the UDP Length to be inconsistent with the IP transport payload length [RFC768]. Such inconsistency has been utilized in UDP-Lite using a different transport number. There are no known systems that use this inconsistency for UDP [RFC3828]. It is possible that such use might interact with UDP options, i.e., where legacy systems might generate UDP datagrams Touch Expires July 3, 2017 [Page 12] Internet-Draft Transport Options for UDP January 2017 that appear to have UDP options. The UDP OCS provides protection against such events and is stronger than a static "magic number". UDP options have been tested as interoperable with Linux, Max OS-X, and Windows Cygwin, and worked through NAT devices. These systems successfully delivered only the user data indicated by the UDP Length field and silently discarded the surplus area. There was one embedded device reported that passed the entire IP transport payload to the user UDP socket. This is already inconsistent with UDP and host requirements [RFC768] [RFC1122], as it presents the entire IP transport payload to the user (including the transport header) instead of presenting the transport payload to the corresponding to the transport protocol, where the transport header would have been removed. It has been reported that Alcatel-Lucent's "Brick" Intrusion Detection System has a default configuration that interprets inconsistencies between UDP Length and IP Length as an attack to be reported. Note that other firewall systems, e.g., CheckPoint, use a default "relaxed UDP length verification" to avoid falsely interpreting this inconsistency as an attack. (TBD: test with UDP checksum offload and UDP fragmentation offload) 9. Options in a Stateless, Unreliable Transport Protocol There are two ways to interpret options for a stateless, unreliable protocol -- an option is either local to the message or intended to affect a stream of messages in a soft-state manner. Either interpretation is valid for defined UDP options. It is impossible to know in advance whether an endpoint supports a UDP option. >> UDP options MUST allow for silent failure on first receipt. >> UDP options that rely on soft-state exchange MUST allow for message reordering and loss. >> A UDP option MUST be silently optional until confirmed by exchange with an endpoint. It is useful that the above requirements prevent using UDP options to implement transport-layer fragmentation and reassembly unless that capability has been negotiated with an endpoint in advance for Touch Expires July 3, 2017 [Page 13] Internet-Draft Transport Options for UDP January 2017 a socket pair. Legacy systems would need to be able to interpret the transport payload fragments as individual transport datagrams. 10. Security Considerations The use of UDP packets with inconsistent IP and UDP Length fields has the potential to trigger a buffer overflow error if not properly handled, e.g., if space is allocated based on the smaller field and copying is based on the larger. However, there have been no reports of such a vulnerability and it would rely on inconsistent use of the two fields for memory allocation and copying. 11. IANA Considerations Upon publication, IANA is hereby requested to create a new registry for UDP Option Kind numbers, similar to that for TCP Option Kinds. Initial values of this registry are as indicated herein. Additional values in this registry are to be assigned by IESG Approval or Standards Action [RFC5226]. Upon publication, IANA is hereby requested to create a new registry for UDP Experimental Option Experiment Identifiers (UDP ExIDs) for use in a similar manner as TCP ExIDs [RFC6994]. Values in this registry are to be assigned by IANA using first-come, first-served (FCFS) rules [RFC5226]. 12. References 12.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. 12.2. Informative References [Hi15] Hildebrand, J., B. Trammel, "Substrate Protocol for User Datagrams (SPUD) Prototype," draft-hildebrand-spud- prototype-03, Mar. 2015. [RFC768] Postel, J., "User Datagram Protocol", RFC 768, August 1980. [RFC791] Postel, J., "Internet Protocol," RFC 791, Sept. 1981. [RFC793] Postel, J., "Transmission Control Protocol" RFC 793, September 1981. Touch Expires July 3, 2017 [Page 14] Internet-Draft Transport Options for UDP January 2017 [RFC1122] Braden, R., Ed., "Requirements for Internet Hosts -- Communication Layers," RFC 1122, Oct. 1989. [RFC2460] Deering, S., R. Hinden, "Internet Protocol Version 6 (IPv6) Specification," RFC 2460, Dec. 1998. [RFC4340] Kohler, E., M. Handley, and S. Floyd, "Datagram Congestion Control Protocol (DCCP)", RFC 4340, March 2006. [RFC4960] Stewart, R. (Ed.), "Stream Control Transmission Protocol", RFC 4960, September 2007. [RFC3692] Narten, T., "Assigning Experimental and Testing Numbers Considered Useful," RFC 3692, Jan. 2004. [RFC3828] Larzon, L-A., M. Degermark, S. Pink, L-E. Jonsson (Ed.), G. Fairhurst (Ed.), "The Lightweight User Datagram Protocol (UDP-Lite)," RFC 3828, July 2004. [RFC5226] Narten, T., H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs," RFC 5226, May 2008. [RFC5925] Touch, J., A. Mankin, R. Bonica, "The TCP Authentication Option," RFC 5925, June 2010. [RFC6994] Touch, J., "Shared Use of Experimental TCP Options," RFC 6994, Aug. 2013. [RFC7323] Borman, D., R. Braden, V. Jacobson, R. Scheffenegger (Ed.), "TCP Extensions for High Performance," RFC 7323, Sep. 2014. [Tr15] Trammel, B. (Ed.), M. Kuelewind (Ed.), "Requirements for the design of a Substrate Protocol for User Datagrams (SPUD)," draft-trammell-spud-req-04, May 2016. 13. Acknowledgments This work benefitted from feedback from Bob Briscoe, Ken Calvert, Ted Faber, Gorry Fairhurst, C. M. Heard, Tom Herbert, as well as discussions on the IETF SPUD email list. This document was prepared using 2-Word-v2.0.template.dot. Touch Expires July 3, 2017 [Page 15] Internet-Draft Transport Options for UDP January 2017 Authors' Addresses Joe Touch USC/ISI 4676 Admiralty Way Marina del Rey, CA 90292 USA Phone: +1 (310) 448-9151 Email: touch@isi.edu Touch Expires July 3, 2017 [Page 16]