Network Working Group F. Templin, Ed. Internet-Draft Boeing Research & Technology Intended status: Standards Track January 19, 2011 Expires: July 23, 2011 Virtual Enterprise Traversal (VET) draft-templin-intarea-vet-23.txt Abstract Enterprise networks connect hosts and routers over various link types, and often also connect to provider networks and/or the global Internet. Enterprise network nodes require a means to automatically provision addresses/prefixes and support internetworking operation in a wide variety of use cases including Small Office, Home Office (SOHO) networks, Mobile Ad hoc Networks (MANETs), ISP networks, multi-organizational corporate networks and the interdomain core of the global Internet itself. This document specifies a Virtual Enterprise Traversal (VET) abstraction for autoconfiguration and operation of nodes in enterprise networks. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on July 23, 2011. Copyright Notice Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents Templin Expires July 23, 2011 [Page 1] Internet-Draft VET January 2011 carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Enterprise Network Characteristics . . . . . . . . . . . . . . 11 4. Autoconfiguration . . . . . . . . . . . . . . . . . . . . . . 13 4.1. Enterprise Router (ER) Autoconfiguration . . . . . . . . . 13 4.2. VET Border Router (VBR) Autoconfiguration . . . . . . . . 15 4.2.1. VET Interface Initialization . . . . . . . . . . . . . 15 4.2.2. Potential Router List (PRL) Discovery . . . . . . . . 15 4.2.3. Provider-Aggregated (PA) EID Prefix Autoconfiguration . . . . . . . . . . . . . . . . . . 16 4.2.4. Provider-(In)dependent (PI) EID Prefix Autoconfiguration . . . . . . . . . . . . . . . . . . 18 4.3. VET Border Gateway (VBG) Autoconfiguration . . . . . . . . 18 4.4. VET Host Autoconfiguration . . . . . . . . . . . . . . . . 19 5. Internetworking Operation . . . . . . . . . . . . . . . . . . 20 5.1. Routing Protocol Participation . . . . . . . . . . . . . . 20 5.1.1. PI Prefix Routing Considerations . . . . . . . . . . . 20 5.2. Default Route Configuration and Selection . . . . . . . . 21 5.3. Address Selection . . . . . . . . . . . . . . . . . . . . 21 5.4. Next Hop Determination . . . . . . . . . . . . . . . . . . 22 5.5. VET Interface Encapsulation/Decapsulation . . . . . . . . 23 5.5.1. Inner Network Layer Protocol . . . . . . . . . . . . . 23 5.5.2. Mid-Layer Encapsulation . . . . . . . . . . . . . . . 23 5.5.3. SEAL Encapsulation . . . . . . . . . . . . . . . . . . 23 5.5.4. Outer UDP Header Encapsulation . . . . . . . . . . . . 24 5.5.5. Outer IP Header Encapsulation . . . . . . . . . . . . 25 5.5.6. Decapsulation . . . . . . . . . . . . . . . . . . . . 25 5.6. Mobility and Multihoming Considerations . . . . . . . . . 25 5.7. Neighbor Coordination on VET Interfaces using SEAL . . . . 26 5.7.1. Router Discovery . . . . . . . . . . . . . . . . . . . 28 5.7.2. Neighbor Unreachability Detection . . . . . . . . . . 28 5.7.3. Redirect Function . . . . . . . . . . . . . . . . . . 29 5.8. Neighbor Coordination on VET Interfaces using IPsec . . . 30 5.9. Multicast . . . . . . . . . . . . . . . . . . . . . . . . 30 5.9.1. Multicast over (Non)Multicast Enterprise Networks . . 30 5.9.2. Multicast Over Multicast-Capable Enterprise Networks . . . . . . . . . . . . . . . . . . . . . . . 31 5.10. Service Discovery . . . . . . . . . . . . . . . . . . . . 32 5.11. VET Link Partitioning . . . . . . . . . . . . . . . . . . 32 Templin Expires July 23, 2011 [Page 2] Internet-Draft VET January 2011 5.12. VBG Prefix State Recovery . . . . . . . . . . . . . . . . 32 5.13. Support for Legacy ISATAP Services . . . . . . . . . . . . 32 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 33 7. Security Considerations . . . . . . . . . . . . . . . . . . . 33 8. Related Work . . . . . . . . . . . . . . . . . . . . . . . . . 33 9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 34 10. Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 34 11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 35 11.1. Normative References . . . . . . . . . . . . . . . . . . . 35 11.2. Informative References . . . . . . . . . . . . . . . . . . 36 Appendix A. Duplicate Address Detection (DAD) Considerations . . 41 Appendix B. Anycast Services . . . . . . . . . . . . . . . . . . 41 Appendix C. Change Log . . . . . . . . . . . . . . . . . . . . . 42 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 45 Templin Expires July 23, 2011 [Page 3] Internet-Draft VET January 2011 1. Introduction Enterprise networks [RFC4852] connect hosts and routers over various link types (see [RFC4861], Section 2.2). The term "enterprise network" in this context extends to a wide variety of use cases and deployment scenarios. For example, an "enterprise" can be as small as a Small Office, Home Office (SOHO) network, as complex as a multi- organizational corporation, or as large as the global Internet itself. Internet Service Provider (ISP) networks are another example use case that fits well with the VET enterprise network model. Mobile Ad hoc Networks (MANETs) [RFC2501] can also be considered as a challenging example of an enterprise network, in that their topologies may change dynamically over time and that they may employ little/no active management by a centralized network administrative authority. These specialized characteristics for MANETs require careful consideration, but the same principles apply equally to other enterprise network scenarios. This document specifies a Virtual Enterprise Traversal (VET) abstraction for autoconfiguration and internetworking operation, where addresses of different scopes may be assigned on various types of interfaces with diverse properties. Both IPv4/ICMPv4 [RFC0791][RFC0792] and IPv6/ICMPv6 [RFC2460][RFC4443] are discussed within this context (other network layer protocols are also considered). The use of standard DHCP [RFC2131] [RFC3315] is assumed unless otherwise specified. Templin Expires July 23, 2011 [Page 4] Internet-Draft VET January 2011 Provider-Edge Interfaces x x x | | | +--------------------+---+--------+----------+ E | | | | | n | I | | .... | | t | n +---+---+--------+---+ | e | t | +--------+ /| | r | e I x----+ | Host | I /*+------+--< p I | r n | |Function| n|**| | r n | n t | +--------+ t|**| | i t | a e x----+ V e|**+------+--< s e | l r . | E r|**| . | e r | f . | T f|**| . | f | V a . | +--------+ a|**| . | I a | i c . | | Router | c|**| . | n c | r e x----+ |Function| e \*+------+--< t e | t s | +--------+ \| | e s | u +---+---+--------+---+ | r | a | | .... | | i | l | | | | o +--------------------+---+--------+----------+ r | | | x x x Enterprise-Edge Interfaces Figure 1: Enterprise Router (ER) Architecture Figure 1 above depicts the architectural model for an Enterprise Router (ER). As shown in the figure, an ER may have a variety of interface types including enterprise-edge, enterprise-interior, provider-edge, internal-virtual, as well as VET interfaces used for encapsulating inner network layer protocol packets for transmission over outer IPv4 or IPv6 networks. The different types of interfaces are defined, and the autoconfiguration mechanisms used for each type are specified. This architecture applies equally for MANET routers, in which enterprise-interior interfaces typically correspond to the wireless multihop radio interfaces associated with MANETs. Out of scope for this document is the autoconfiguration of provider interfaces, which must be coordinated in a manner specific to the service provider's network. Enterprise networks require a means for supporting both Provider- (In)dependent (PI) and Provider-Aggregated (PA) addressing. This is especially true for enterprise network scenarios that involve mobility and multihoming. The VET specification provides adaptable mechanisms that address these and other issues in a wide variety of enterprise network use cases. Templin Expires July 23, 2011 [Page 5] Internet-Draft VET January 2011 The VET framework builds on a Non-Broadcast Multiple Access (NBMA) [RFC2491] virtual interface model in a manner similar to other automatic tunneling technologies [RFC2529][RFC5214]. VET interfaces support the encapsulation of inner network layer protocol packets over IP networks (i.e., either IPv4 or IPv6). VET is also compatible with mid-layer encapsulation technologies including IPsec [RFC4301], and supports both stateful and stateless prefix delegation. VET and its associated technologies (including the Subnetwork Encapsulation and Adaptation Layer (SEAL) [I-D.templin-intarea-seal]) are functional building blocks for a new Internetworking architecture based on the Internet Routing Overlay Network (IRON) [I-D.templin-iron] and Routing and Addressing in Networks with Global Enterprise Recursion (RANGER) [RFC5720] [I-D.russert-rangers]. Many of the VET principles can be traced to the deliberations of the ROAD group in January 1992, and also to still earlier initiatives including NIMROD [RFC1753] and the Catenet model for internetworking [CATENET] [IEN48] [RFC2775]. The high-level architectural aspects of the ROAD group deliberations are captured in a "New Scheme for Internet Routing and Addressing (ENCAPS) for IPNG" [RFC1955]. VET is related to the present-day activities of the IETF INTAREA, AUTOCONF, DHC, IPv6, MANET, and V6OPS working groups, as well as the IRTF RRG working group. 2. Terminology The mechanisms within this document build upon the fundamental principles of IP encapsulation. The term "inner" refers to the innermost {address, protocol, header, packet, etc.} *before* encapsulation, and the term "outer" refers to the outermost {address, protocol, header, packet, etc.} *after* encapsulation. VET also accommodates "mid-layer" encapsulations including the Subnetwork Encapsulation and Adaptation Layer (SEAL) [I-D.templin-intarea-seal], IPsec [RFC4301], etc. The terminology in the normative references apply; the following terms are defined within the scope of this document: Virtual Enterprise Traversal (VET) an abstraction that uses encapsulation to create virtual overlays for transporting inner network layer packets over outer IPv4 and IPv6 enterprise networks. Templin Expires July 23, 2011 [Page 6] Internet-Draft VET January 2011 enterprise network the same as defined in [RFC4852]. An enterprise network is further understood to refer to a cooperative networked collective of devices within a structured IP routing and addressing plan and with a commonality of business, social, political, etc., interests. Minimally, the only commonality of interest in some enterprise network scenarios may be the cooperative provisioning of connectivity itself. subnetwork the same as defined in [RFC3819]. site a logical and/or physical grouping of interfaces that connect a topological area less than or equal to an enterprise network in scope. From a network organizational standpoint, a site within an enterprise network can be considered as an enterprise network unto itself. Mobile Ad hoc Network (MANET) a connected topology of mobile or fixed routers that maintain a routing structure among themselves over links that often have dynamic connectivity properties. The characteristics of MANETs are described in [RFC2501], Section 3, and a wide variety of MANETs share common properties with enterprise networks. enterprise/site/MANET throughout the remainder of this document, the term "enterprise network" is used to collectively refer to any of {enterprise, site, MANET}, i.e., the VET mechanisms and operational principles can be applied to enterprises, sites, and MANETs of any size or shape. VET link a virtual link that uses automatic tunneling to create an overlay network that spans an enterprise network routing region. VET links can be segmented (e.g., by filtering gateways) into multiple distinct segments that can be joined together by bridges or IP routers the same as for any link. Bridging would view the multiple (bridged) segments as a single VET link, whereas IP routing would view the multiple segments as multiple distinct VET links. VET links can further be partitioned into multiple logical areas, where each area is identified by a distinct set of border nodes. Templin Expires July 23, 2011 [Page 7] Internet-Draft VET January 2011 VET links configured over non-multicast enterprise networks support only Non-Broadcast, Multiple Access (NBMA) services; VET links configured over enterprise networks that support multicast can support both NBMA and native multicast services. All nodes connected to the same VET link appear as neighbors from the standpoint of the inner network layer. Enterprise Router (ER) As depicted in Figure 1, an Enterprise Router (ER) is a fixed or mobile router that comprises a router function, a host function, one or more enterprise-interior interfaces, and zero or more internal virtual, enterprise-edge, provider-edge, and VET interfaces. At a minimum, an ER forwards outer IP packets over one or more sets of enterprise-interior interfaces, where each set connects to a distinct enterprise network. VET Border Router (VBR) an ER that connects edge networks to VET links and/or connects multiple VET links together. A VBR is a tunnel endpoint router, and it configures a separate VET interface for each distinct VET link. All VBRs are also ERs. VET Border Gateway (VBG) a VBR that connects VET links to provider networks. A VBG may alternately act as "half-gateway", and forward the packets it receives from neighbors on the VET link to another VBG on the same VET link. All VBGs are also VBRs. VET host any node (host or router) that configures a VET interface for host-operation only. Note that a node may configure some of its VET interfaces as host interfaces and others as router interfaces. VET node any node (host or router) that configures and uses a VET interface. enterprise-interior interface an ER's attachment to a link within an enterprise network. Packets sent over enterprise-interior interfaces may be forwarded over multiple additional enterprise-interior interfaces within the enterprise network before they reach either their final destination or a border router/gateway. Enterprise-interior interfaces connect laterally within the IP network hierarchy. Templin Expires July 23, 2011 [Page 8] Internet-Draft VET January 2011 enterprise-edge interface a VBR's attachment to a link (e.g., an Ethernet, a wireless personal area network, etc.) on an arbitrarily complex edge network that the VBR connects to a VET link and/or a provider network. Enterprise-edge interfaces connect to lower levels within the IP network hierarchy. provider-edge interface a VBR's attachment to the Internet or to a provider network via which the Internet can be reached. Provider-edge interfaces connect to higher levels within the IP network hierarchy. internal-virtual interface an interface that is internal to a VET node and does not in itself directly attach to a tangible link, e.g., a loopback interface. VET interface a VET node's attachment to a VET link. VET nodes configure each VET interface over a set of underlying enterprise-interior interfaces that connect to a routing region spanned by a single VET link. When there are multiple distinct VET links (each with their own distinct set of underlying interfaces), the VET node configures a separate VET interface for each link. The VET interface encapsulates each inner packet in any mid-layer headers followed by an outer IP header, then forwards the packet on an underlying interface such that the Time to Live (TTL) - Hop Limit in the inner header is not decremented as the packet traverses the link. The VET interface therefore presents an automatic tunneling abstraction that represents the VET link as a single hop to the inner network layer. Provider Aggregated (PA) prefix a network layer protocol prefix that is delegated to a VET node by a provider network. Provider-(In)dependent (PI) address/prefix a network layer protocol prefix that is delegated to a VET node by an independent prefix registration authority. Routing Locator (RLOC) a public-scope or enterprise-local-scope IP address that can appear in enterprise-interior and/or interdomain routing tables. Public-scope RLOCs are delegated to specific enterprise networks and routable within both the enterprise-interior and interdomain routing regions. Enterprise-local-scope RLOCs (e.g., IPv6 Unique Local Addresses [RFC4193], IPv4 privacy addresses [RFC1918], etc.) are self-generated by individual enterprise networks and routable Templin Expires July 23, 2011 [Page 9] Internet-Draft VET January 2011 only within the enterprise-interior routing region. ERs use RLOCs for operating the enterprise-interior routing protocol and for next-hop determination in forwarding packets addressed to other RLOCs. End systems can use RLOCs as addresses for end-to-end communications between peers within the same enterprise network. VET interfaces treat RLOCs as *outer* IP addresses during encapsulation. Endpoint Interface iDentifier (EID) a public-scope network layer address that is routable within enterprise-edge and/or VET overlay networks. In a pure mapping system, EID prefixes are not routable within the interdomain routing system. In a hybrid routing/mapping system, EID prefixes may be represented within the same interdomain routing instances that distribute RLOC prefixes. In either case, EID prefixes are separate and distinct from any RLOC prefix space, but they are mapped to RLOC addresses to support packet forwarding over VET interfaces. VBRs participate in any EID-based routing instances and use EID addresses for next-hop determination. End systems can use EIDs as addresses for end-to-end communications between peers either within the same enterprise network or within different enterprise networks. VET interfaces treat EIDs as *inner* network layer addresses during encapsulation. Note that an EID can also be used as an *outer* network layer address if there are nested encapsulations. In that case, the EID would appear as an RLOC to the innermost encapsulation. The following additional acronyms are used throughout the document: CGA - Cryptographically Generated Address DHCP(v4, v6) - Dynamic Host Configuration Protocol ECMP - Equal Cost Multi Path FIB - Forwarding Information Base ICMP - either ICMPv4 or ICMPv6 IP - either IPv4 or IPv6 ISATAP - Intra-Site Automatic Tunnel Addressing Protocol NBMA - Non-Broadcast, Multiple Access ND - Neighbor Discovery PIO - Prefix Information Option PRL - Potential Router List PRLNAME - Identifying name for the PRL RIB - Routing Information Base RIO - Route Information Option SCMP - SEAL Control Message Protocol Templin Expires July 23, 2011 [Page 10] Internet-Draft VET January 2011 SEAL - Subnetwork Encapsulation and Adaptation Layer SLAAC - IPv6 StateLess Address AutoConfiguration SNS/SNA - SEAL Neighbor Solicitation/Advertisement SRS/SRA - SEAL Router Solicitation/Advertisement The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. When used in lower case (e.g., must, must not, etc.), these words MUST NOT be interpreted as described in [RFC2119], but are rather interpreted as they would be in common English. 3. Enterprise Network Characteristics Enterprise networks consist of links that are connected by Enterprise Routers (ERs) as depicted in Figure 1. ERs typically participate in a routing protocol over enterprise-interior interfaces to discover routes that may include multiple Layer 2 or Layer 3 forwarding hops. VET Border Routers (VBRs) are ERs that connect edge networks to VET links that span enterprise networks. VET Border Gateways (VBGs) are VBRs that connect VET links to provider networks. Conceptually, an ER embodies both a host function and router function, and supports communications according to the weak end- system model [RFC1122]. The router function engages in the enterprise-interior routing protocol on its enterprise-interior interfaces, connects any of the ER's edge networks to its VET links, and may also connect the VET links to provider networks (see Figure 1). The host function typically supports network management applications, but may also support diverse applications typically associated with general-purpose computing platforms. An enterprise network may be as simple as a small collection of ERs and their attached edge networks; an enterprise network may also contain other enterprise networks and/or be a subnetwork of a larger enterprise network. An enterprise network may further encompass a set of branch offices and/or nomadic hosts connected to a home office over one or several service providers, e.g., through Virtual Private Network (VPN) tunnels. Finally, an enterprise network may contain many internal partitions that are logical or physical groupings of nodes for the purpose of load balancing, organizational separation, etc. In that case, each internal partition resembles an individual segment of a bridged LAN. Enterprise networks that comprise link types with sufficiently similar properties (e.g., Layer 2 (L2) address formats, maximum transmission units (MTUs), etc.) can configure a subnetwork routing Templin Expires July 23, 2011 [Page 11] Internet-Draft VET January 2011 service such that the inner network layer sees the underlying network as an ordinary shared link the same as for a (bridged) campus LAN (this is often the case with large cellular operator networks). In that case, a single inner network layer hop is sufficient to traverse the underlying network. Enterprise networks that comprise link types with diverse properties and/or configure multiple IP subnets must also provide an enterprise-interior routing service that operates as an IP layer mechanism. In that case, multiple inner network layer hops may be necessary to traverse the underlying network such that care must be taken to avoid multi-link subnet issues [RFC4903]. In addition to other interface types, VET nodes configure VET interfaces that view all other nodes on the VET link as neighbors on a virtual NBMA link. VET nodes configure a separate VET interface for each distinct VET link to which they connect, and discover neighbors on the link that can be used for forwarding packets to off- link destinations. VET interface neighbor relationships may be either unidirectional or bidirectional. A unidirectional neighbor relationship is typically established and maintained as a result of network layer control protocol messaging in a manner that parallels IPv6 neighbor discovery [RFC4861]. A bidirectional neighbor relationship is typically established and maintained as result of a short transaction between the neighbors carried by a reliable transport protocol such as TCP. The protocol details of the transaction are out of scope for this document, and indeed need not be standardized as long as both neighbors observe the same specifications. For each distinct VET link , a trust basis must be established and consistently applied. For example, for VET links configured over enterprise networks in which VBRs establish symmetric security associations, mechanisms such as IPsec [RFC4301] can be used to assure authentication and confidentiality. In other enterprise network scenarios, VET links may require asymmetric securing mechanisms such as SEcure Neighbor Discovery (SEND) [RFC3971]. VET links configured over still other enterprise networks may find it sufficient to employ additional encapsulations (e.g., SEAL [I-D.templin-intarea-seal]) that include a simple per-packet nonce to detect off-path attacks. Finally, for VET links configured over enterprise networks with a centralized management structure (e.g., a corporate campus network, an ISP network, etc.), a hybrid routing/mapping service can be deployed using a synchronized set of VBGs. In that case, the VBGs can provide a "default mapper" [I-D.jen-apt] service used for short- term packet forwarding until route-optimized paths can be established. For VET links configured over enterprise networks with Templin Expires July 23, 2011 [Page 12] Internet-Draft VET January 2011 a distributed management structure (e.g., disconnected MANETs), peer- to-peer coordination between the VET nodes themselves without the assistance of VBGs may be required. Recognizing that various use cases will entail a continuum between a fully centralized and fully distributed approach, the following sections present the mechanisms of Virtual Enterprise Traversal as they apply to a wide variety of scenarios. 4. Autoconfiguration ERs, VBRs, VBGs, and VET hosts configure themselves for operation as specified in the following subsections. 4.1. Enterprise Router (ER) Autoconfiguration ERs configure enterprise-interior interfaces and engage in any routing protocols over those interfaces. When an ER joins an enterprise network, it first configures an IPv6 link-local address on each enterprise-interior interface that requires an IPv6 link-local capability and configures an IPv4 link- local address on each enterprise-interior interface that requires an IPv4 link-local capability. IPv6 link-local address generation mechanisms include Cryptographically Generated Addresses (CGAs) [RFC3972], IPv6 Privacy Addresses [RFC4941], StateLess Address AutoConfiguration (SLAAC) using EUI-64 interface identifiers [RFC4291] [RFC4862], etc. The mechanisms specified in [RFC3927] provide an IPv4 link-local address generation capability. Next, the ER configures one or more RLOCs and engages in any routing protocols on its enterprise-interior interfaces. The ER can configure RLOCs via administrative configuration, pseudo-random self- generation from a suitably large address pool, DHCP autoconfiguration, or through an alternate autoconfiguration mechanism. Pseudo-random self-generation of IPv6 RLOCs can be from a large public or local-use IPv6 address range (e.g., IPv6 Unique Local Addresses [RFC4193]). Pseudo-random self-generation of IPv4 RLOCs can be from a large public or local-use IPv4 address range (e.g., [RFC1918]). When self-generation is used alone, the ER continuously monitors the RLOCs for uniqueness, e.g., by monitoring the enterprise-interior routing protocol. (Note however that anycast RLOCs may be assigned to multiple enterprise-interior interfaces; hence, monitoring for uniqueness applies only to RLOCs that are provisioned as unicast.) Templin Expires July 23, 2011 [Page 13] Internet-Draft VET January 2011 DHCP autoconfiguration of RLOCs uses standard DHCP procedures, however ERs acting as DHCP clients SHOULD also use DHCP Authentication [RFC3118] [RFC3315] as discussed further below. In typical enterprise network scenarios (i.e., those with stable links), it may be sufficient to configure one or a few DHCP relays on each link that does not include a DHCP server. In more extreme scenarios (e.g., MANETs that include links with dynamic connectivity properties), DHCP operation may require any ERs that have already configured RLOCs to act as DHCP relays to ensure that client DHCP requests eventually reach a DHCP server. This may result in considerable DHCP message relaying until a server is located, but the DHCP Authentication Replay Detection vector provides relays with a means for avoiding message duplication. In all enterprise network scenarios, the amount of DHCP relaying required can be significantly reduced if each relay has a way of contacting a DHCP server directly. In particular, if the relay can discover the unicast addresses for one or more servers (e.g., by discovering the unicast RLOC addresses of VBGs as described in Section 4.2.2) it can forward DHCP requests directly to the unicast address(es) of the server(s). If the relay does not know the unicast address of a server, it can forward DHCP requests to a site-scoped DHCP server multicast address if the enterprise network supports site-scoped multicast services. For DHCPv6, relays can forward requests to the site-scoped IPv6 multicast group address 'All_DHCP_Servers' [RFC3315]. For DHCPv4, relays can forward requests to the site-scoped IPv4 multicast group address 'All_DHCPv4_Servers', which SHOULD be set to 239.255.2.1 unless an alternate multicast group for the enterprise network is known. DHCPv4 servers that delegate RLOCs SHOULD therefore join the 'All_DHCPv4_Servers' multicast group and service any DHCPv4 messages received for that group. A combined approach using both DHCP and self-generation is also possible when the ER configures both a DHCP client and relay that are connected, e.g., via a pair of back-to-back connected Ethernet interfaces, a tun/tap interface, a loopback interface, inter-process communication, etc. The ER first self-generates an RLOC taken from a temporary addressing range used only for the bootstrapping purpose of procuring an actual RLOC taken from a delegated addressing range. The ER then engages in the enterprise-interior routing protocol and performs a DHCP exchange as above using the temporary RLOC as the address of its relay function. When the DHCP server delegates an actual RLOC address/prefix, the ER abandons the temporary RLOC and re-engages in the enterprise-interior routing protocol using an RLOC taken from the delegation. Alternatively (or in addition to the above), the ER can request RLOC Templin Expires July 23, 2011 [Page 14] Internet-Draft VET January 2011 prefix delegations via an automated prefix delegation exchange over an enterprise-interior interface and can assign the prefix(es) on enterprise-edge interfaces. Note that in some cases, the same enterprise-edge interfaces may assign both RLOC and EID addresses if there is a means for source address selection. In other cases (e.g., for separation of security domains), RLOCs and EIDs are assigned on separate sets of enterprise-edge interfaces. In some enterprise network scenarios (e.g., MANETs that include links with dynamic connectivity properties), assignment of RLOCs on enterprise-interior interfaces as singleton addresses (i.e., as addresses with /32 prefix lengths for IPv4, or as addresses with /128 prefix lengths for IPv6) MAY be necessary to avoid multi-link subnet issues. 4.2. VET Border Router (VBR) Autoconfiguration VBRs are ERs that configure and use one or more VET interfaces. In addition to the ER autoconfiguration procedures specified in Section 4.1, VBRs perform the following autoconfiguration operations. 4.2.1. VET Interface Initialization VBRs configure a separate VET interface for each VET link, where each VET link spans a distinct sets of underlying links belonging to the same enterprise network. All nodes on the VET link appear as single- hop neighbors from the standpoint of the inner network layer protocol through the use of encapsulation. The VBR binds each VET interface to one or more underlying interfaces, and uses the underlying interface addresses as RLOCs to serve as the outer source addresses for encapsulated packets. The VBR then assigns a link-local address to each VET interface if necessary. When IPv6 and IPv4 are used as the inner/outer protocols (respectively), the VBR can autoconfigure an IPv6 link-local address on the VET interface using a modified EUI-64 interface identifier based on an IPv4 RLOC address (see Section 2.2.1 of [RFC5342]). Link-local address configuration for other inner/outer protocol combinations is through administrative configuration, random self- generation (e.g., [RFC4941], etc.) or through an unspecified alternate method. 4.2.2. Potential Router List (PRL) Discovery After initializing the VET interface, the VBR next discovers a Potential Router List (PRL) for the VET link that includes the RLOC addresses of VBGs. The PRL can be discovered through administrative configuration, information conveyed in the enterprise-interior Templin Expires July 23, 2011 [Page 15] Internet-Draft VET January 2011 routing protocol, an anycast VBG discovery message exchange, a DHCP option, etc. In multicast-capable enterprise networks, VBRs can also listen for advertisements on the 'rasadv' [RASADV] multicast group address. When no other information is available, the VBR can resolve an identifying name for the PRL ('PRLNAME') formed as 'hostname.domainname', where 'hostname' is an enterprise-specific name string and 'domainname' is an enterprise-specific Domain Name System (DNS) suffix [RFC1035]. The VBR discovers 'PRLNAME' through administrative configuration, the DHCP Domain Name option [RFC2132], 'rasadv' protocol advertisements, link-layer information (e.g., an IEEE 802.11 Service Set Identifier (SSID)), or through some other means specific to the enterprise network. The VBR can also obtain 'PRLNAME' as part of an arrangement with a private-sector PI prefix vendor (see: Section 4.2.4). In the absence of other information, the VBR sets the 'hostname' component of 'PRLNAME' to "isatapv2" and sets the 'domainname' component to an enterprise-specific DNS suffix (e.g., "example.com"). Isolated enterprise networks that do not connect to the outside world may have no enterprise-specific DNS suffix, in which case the 'PRLNAME' consists only of the 'hostname' component. (Note that the default hostname "isatapv2" is intentionally distinct from the convention specified in [RFC5214].) After discovering 'PRLNAME', the VBR resolves the name into a list of RLOC addresses through a name service lookup. For centrally managed enterprise networks, the VBR resolves 'PRLNAME' using an enterprise- local name service (e.g., the DNS). For enterprises with no centralized management structure, the VBR resolves 'PRLNAME' using Link-Local Multicast Name Resolution (LLMNR) [RFC4795] over the VET interface. In that case, all VBGs in the PRL respond to the LLMNR query, and the VBR accepts the union of all responses. 4.2.3. Provider-Aggregated (PA) EID Prefix Autoconfiguration VBRs that connect their enterprise networks to a provider network obtain Provider-Aggregated (PA) EID prefixes through stateful and/or stateless autoconfiguration mechanisms. The stateful and stateless approaches are discussed in the following subsections. 4.2.3.1. Stateful Prefix Delegation For IPv4, VBRs acquire IPv4 PA EID prefixes through administrative configuration, an automated IPv4 prefix delegation exchange, etc. For IPv6, VBRs acquire IPv6 PA EID prefixes through administrative Templin Expires July 23, 2011 [Page 16] Internet-Draft VET January 2011 configuration or through DHCPv6 Prefix Delegation exchanges with an VBG acting as a DHCP relay/server. In particular, the VBR (acting as a requesting router) can use DHCPv6 prefix delegation [RFC3633] over the VET interface to obtain prefixes from the VBG (acting as a delegating router). The VBR obtains prefixes using either a 2-message or 4-message DHCPv6 exchange [RFC3315]. To perform the 2-message exchange, the VBR's DHCPv6 client function can send a Solicit message with an IA_PD option either directly or via the VBR's own DHCPv6 relay function (see Section 4.1). The VBR's VET interface then forwards the message using VET encapsulation (see: Section 5.4) to a VBG which either services the request or relays it further. The forwarded Solicit message will elicit a Reply message from the server containing prefix delegations. The VBR can also propose a specific prefix to the DHCPv6 server per Section 7 of [RFC3633]. The server will check the proposed prefix for consistency and uniqueness, then return it in the Reply message if it was able to perform the delegation. After the VBR receives IPv4 and/or IPv6 prefix delegations, it can provision the prefixes on enterprise-edge interfaces as well as on other VET interfaces configured over child enterprise networks for which it acts as an VBG. The VBR can also provision the prefixes on enterprise-interior interfaces to service directly-attached hosts on the enterprise-interior link. The prefix delegations remain active as long as the VBR continues to renew them via the delegating VBG before lease lifetimes expire. The lease lifetime also keeps the delegation state active even if communications between the VBR and delegating VBG are disrupted for a period of time (e.g., due to an enterprise network partition, power failure, etc.). Note however that if the VBR abandons or otherwise loses continuity with the prefixes, it may be obliged to perform network-wide renumbering if it subsequently receives a new and different set of prefixes. Stateful prefix delegation for non-IP protocols is out of scope. 4.2.3.2. Stateless Prefix Delegation When IPv6 and IPv4 are used as the inner and outer protocols, respectively, a stateless IPv6 PA prefix delegation capability is available using the mechanisms specified in [RFC5569][RFC5969]. VBRs can use these mechanisms to statelessly configure IPv6 PA prefixes that embed one of the VBR's IPv4 RLOCs. Using this stateless prefix delegation, if the IPv4 RLOC changes the IPv6 prefix also changes and the VBR is obliged to renumber any Templin Expires July 23, 2011 [Page 17] Internet-Draft VET January 2011 interfaces on which sub-prefixes from the delegated prefix are assigned. This method may therefore be most suitable for enterprise networks in which IPv4 RLOC assignments rarely change, or in enterprise networks in which only services that do not depend on a long-term stable IPv6 prefix (e.g., client-side web browsing) are used. Stateless prefix delegation for other protocol combinations is out of scope. 4.2.4. Provider-(In)dependent (PI) EID Prefix Autoconfiguration VBRs can acquire Provider (In)dependent (PI) prefixes to facilitate multihoming, mobility and traffic engineering without requiring site- wide renumbering events. These PI prefixes are made available to VBRs through a prefix delegation authority that may or may not be associated with a specific ISP. VBRs that connect major enterprise networks (e.g., large corporations, academic campuses, ISP networks, etc.) to a parent enterprise network and/or the global Internet can acquire short PI prefixes (e.g., an IPv6 ::/20, an IPv4 /16, etc.) through a registration authority such as the Internet Assigned Numbers Authority (IANA) or a major regional Internet registry. VBRs that connect small enterprise networks (e.g., SOHO networks, MANETs, etc.) to a parent enterprise network can acquire longer PI prefixes through arrangements with a PI prefix delegation vendor. After a VBR receives PI prefixes, it can sub-delegate portions of the prefixes on enterprise-edge interfaces, on child VET interfaces for which it is configured as a VBG and on enterprise-interior interfaces to service directly-attached hosts on the enterprise-interior link. The VBR can also sub-delegate portions of its PI prefixes to requesting routers connected to child enterprise networks. These requesting routers consider their sub-delegated portions of the PI prefix as PA, and consider the delegating routers as their points of connection to a provider network. 4.3. VET Border Gateway (VBG) Autoconfiguration VBGs are VBRs that connect VET links configured over child enterprise networks to provider networks via provider-edge interfaces and/or via VET links configured over parent enterprise networks. A VBG may also act as a "half-gateway", in that it may need to forward the packets it receives from neighbors on the VET link via another VBG connected to the same VET link. This arrangement is seen in the IRON [I-D.templin-iron] client/server/relay architecture, in which a server "half-gateway" is a VBG that forwards packets with off-link Templin Expires July 23, 2011 [Page 18] Internet-Draft VET January 2011 destinations via a relay "half-gateway" VBG that connects the VET link to the provider network. VBGs autoconfigure their provider-edge interfaces in a manner that is specific to the provider connections, and they autoconfigure their VET interfaces that were configured over parent VET links using the VBR autoconfiguration procedures specified in Section 4.2. For each of its VET interfaces connected to child VET links, the VBG initializes the interface the same as for an ordinary VBR (see Section 4.2.1). It then arranges to add one or more of its RLOCs associated with the child VET link to the PRL. VBGs configure a DHCP relay/server on VET interfaces connected to child VET links that require DHCP services. VBGs may also engage in an unspecified anycast VBG discovery message exchange if they are configured to do so. Finally, VBGs respond to LLMNR queries for 'PRLNAME' on VET interfaces connected to VET links that span child enterprise networks with a distributed management structure. 4.4. VET Host Autoconfiguration Nodes that cannot be attached via a VBR's enterprise-edge interface (e.g., nomadic laptops that connect to a home office via a Virtual Private Network (VPN)) can instead be configured for operation as a simple host on the VET link. Each VET host performs the same enterprise interior interfaces RLOC configuration procedures as specified for ERs in Section 4.1. The VET host next performs the same VET interface initialization and PRL discovery procedures as specified for VBRs in Section 4.2, except that it configures its VET interfaces as host interfaces (and not router interfaces). Note also that a node may be configured as a host on some VET interfaces and as an VBR/VBG on other VET interfaces. A VET host may receive non-link-local addresses and/or prefixes to assign to the VET interface via DHCP exchanges and/or through information conveyed in Router Advertisements (RAs). If prefixes are provided, however, there must be assurance that either 1) the VET link will not partition, or 2) that each VET host interface connected to the VET link will configure a unique set of prefixes. VET hosts therefore depend on DHCP and/or RA exchanges to provide only addresses/prefixes that are appropriate for assignment to the VET interface according to these specific cases, and depend on the VBGs within the enterprise keeping track of which addresses/prefixes were assigned to which hosts. When the VET host solicits a DHCP-assigned EID address/prefix over a (non-multicast) VET interface, it maps the DHCP relay/server multicast inner destination address to the outer RLOC address of a Templin Expires July 23, 2011 [Page 19] Internet-Draft VET January 2011 VBG that it has selected as a default router. The VET host then assigns any resulting DHCP-delegated addresses/prefixes to the VET interface for use as the source address of inner packets. The host will subsequently send all packets destined to EID correspondents via a default router on the VET link, and will discover more-specific routes based on any redirect messages it receives. 5. Internetworking Operation Following the autoconfiguration procedures specified in Section 4, ERs, VBRs, VBGs, and VET hosts engage in normal internetworking operations as discussed in the following sections. 5.1. Routing Protocol Participation ERs engage in any RLOC-based routing protocols over enterprise- interior interfaces to exchange routing information for forwarding IP packets with RLOC addresses. VBRs and VBGs can additionally engage in any EID-based routing protocols over VET, enterprise-edge and provider-edge interfaces to exchange routing information for forwarding inner network layer packets with EID addresses. Note that any EID-based routing instances are separate and distinct from any RLOC-based routing instances. VBR/VBG routing protocol participation on non-multicast VET interfaces uses the NBMA interface model, e.g., in the same manner as for OSPF over NBMA interfaces [RFC5340]. (VBR/VBG routing protocol participation on multicast-capable VET interfaces can alternatively use the standard multicast interface model, but this may result in excessive multicast control message overhead.) VBRs can use the list of VBGs in the PRL (see: Section 4.2.1) as an initial list of neighbors for EID-based routing protocol participation. VBRs can alternatively use the list of VBGs as potential default routers instead of engaging in an EID-based routing protocol instance. In that case, when the VBR forwards a packet via a default router it may receive a redirect message indicating a different VBR as a better next hop. 5.1.1. PI Prefix Routing Considerations VBRs that connect large enterprise networks to the global Internet advertise their EID PI prefixes directly into the Internet default- free RIB via the Border Gateway Protocol (BGP) [RFC4271] the same as for a major service provider network. VBRs that connect large enterprise networks to provider networks can instead advertise their EID PI prefixes into the providers' routing system(s) if the provider Templin Expires July 23, 2011 [Page 20] Internet-Draft VET January 2011 networks are configured to accept them. VBRs that connect small enterprise networks to provider networks obtain one or more PI prefixes and register the prefixes with a serving VBG in the PI prefix vendor's network (e.g., through a vendor-specific short http(s) transaction). The PI prefix vendor network then acts as a virtual "home" enterprise network that connects its customer small enterprise networks to the Internet routing system. The customer small enterprise networks in turn appear as mobile components of the PI prefix vendor's network, i.e., the customer networks are always "away from home". Further details on routing for PI prefixes is discussed in "The Internet Routing Overlay Network (IRON)" [I-D.templin-iron] and "Fib Suppression with Virtual Aggregation" [I-D.ietf-grow-va]. 5.2. Default Route Configuration and Selection Configuration of default routes in the presence of VET interfaces must be carefully coordinated according to the inner and outer network protocols. If the inner and outer protocols are different (e.g., IPv6 within IPv4) then default routes of the inner protocol version can be configured with next-hops corresponding to default routers on a VET interface while default routes of the outer protocol version can be configured with next-hops corresponding to default routers on an underlying interface. If the inner and outer protocols are the same (e.g., IPv4 within IPv4), care must be taken in setting the default route to avoid ambiguity. For example, if default routes are configured on the VET interface then more-specific routes could be configured on underlying interfaces to avoid looping. In a preferred method, however, multiple default routes can be configured with some having next-hops corresponding to (EID-based) default routers on VET interfaces and others having next-hops corresponding to (RLOC-based) default routers on underlying interfaces. In that case, special next-hop determination rules must be used (see: Section 5.4). 5.3. Address Selection When permitted by policy and supported by enterprise-interior routing, VET nodes can avoid encapsulation through communications that directly invoke the outer IP protocol using RLOC addresses instead of EID addresses for end-to-end communications. For example, an enterprise network that provides native IPv4 intra-enterprise services can provide continued support for native IPv4 communications even when encapsulated IPv6 services are available for inter- enterprise communications. In other enterprise network scenarios, Templin Expires July 23, 2011 [Page 21] Internet-Draft VET January 2011 the use of EID-based communications (i.e., instead of RLOC-based communications) may be necessary and/or beneficial to support address scaling, transparent Network Address Translator (NAT) traversal, security domain separation, site multihoming, traffic engineering, etc. . VET nodes can use source address selection rules (e.g., based on name service information) to determine whether to use EID-based or RLOC- based addressing. The remainder of this section discusses internetworking operation for EID-based communications using the VET interface abstraction. 5.4. Next Hop Determination VET nodes perform normal next-hop determination via longest prefix match, and send packets according to the most-specific matching entry in the FIB. If the FIB entry has multiple next-hop addresses, the VBR selects the next-hop with the best metric value. If multiple next hops have the same metric value, the VET node can use Equal Cost Multi Path (ECMP) to forward different flows via different next-hop addresses, where flows are determined, e.g., by computing a hash of the inner packet's source address, destination address and flow label fields. If the VET node has multiple default routes of the same inner and outer protocol versions, with some corresponding to EID-based default routers and others corresponding to RLOC-based default routers, it must perform source address based selection of a default route. In particular, if the packet's source address is taken from an EID prefix the VET node selects a default route configured over the VET interface; otherwise, it selects a default route configured over an underlying interface. As a last resort when there is no matching entry in the FIB (i.e., not even default), VET nodes can discover neighbors within the enterprise network through on-demand name service queries for the EID prefix taken from a packet's destination address (or, by some other inner address to outer address mapping mechanism). For example, for the IPv6 destination address '2001:DB8:1:2::1' and 'PRLNAME' "isatapv2.example.com" the VET node can perform a name service lookup for the domain name: '0.0.1.0.0.0.8.b.d.0.1.0.0.2.ip6.isatapv2.example.com'. Name-service lookups in enterprise networks with a centralized management structure use an infrastructure-based service, e.g., an enterprise-local DNS. Name-service lookups in enterprise networks with a distributed management structure and/or that lack an infrastructure-based name service instead use LLMNR over the VET Templin Expires July 23, 2011 [Page 22] Internet-Draft VET January 2011 interface. When LLMNR is used, the VBR that performs the lookup sends an LLMNR query (with the prefix taken from the IP destination address encoded in dotted-nibble format as shown above) and accepts the union of all replies it receives from neighbors on the VET interface. When a VET node receives an LLMNR query, it responds to the query IFF it aggregates an IP prefix that covers the prefix in the query. If the name-service lookup succeeds, it will return RLOC addresses (e.g., in DNS A records) that correspond to neighbors to which the VET node can forward packets. 5.5. VET Interface Encapsulation/Decapsulation VET interfaces encapsulate inner network layer packets in any necessary mid-layer headers and trailers (e.g., IPsec [RFC4301], etc.) followed by a SEAL header (if necessary) followed by an outer UDP header (if necessary) followed by an outer IP header. Following all encapsulations, the VET interface submits the encapsulated packet to the outer IP forwarding engine for transmission on an underlying interface. The following sections provide further details on encapsulation: 5.5.1. Inner Network Layer Protocol The inner network layer protocol sees the VET interface as an ordinary network interface, and views the outer network layer protocol as an ordinary L2 transport. The inner- and outer network layer protocol types are mutually independent and can be used in any combination. Inner network layer protocol types include IPv6 [RFC2460] and IPv4 [RFC0791], but they may also include non-IP protocols such as OSI/CLNP [RFC0994][RFC1070][RFC4548]. 5.5.2. Mid-Layer Encapsulation VET interfaces that use mid-layer encapsulations encapsulate each inner network layer packet in any mid-layer headers and trailers as the first step in a potentially multi-layer encapsulation. 5.5.3. SEAL Encapsulation Following any mid-layer encapsulations, VET interfaces that use SEAL add a SEAL header as specified in [I-D.templin-intarea-seal]. Inclusion of a SEAL header must be applied uniformly between all neighbors on the VET link. Note that when a VET interface sends a SEAL-encapsulated packet to a neighbor that does not use SEAL encapsulation, it may receive an ICMP "port unreachable" or "protocol unreachable" depending on whether/not an outer UDP header is Templin Expires July 23, 2011 [Page 23] Internet-Draft VET January 2011 included. SEAL encapsulation is used on VET links that require path MTU mitigations due to encapsulation overhead and/or mechanisms for VET interface neighbor coordination. When SEAL encapsulation is used, the VET interface sets the 'Next Header' value in the SEAL header to the IP protocol number associated with either the mid-layer encapsulation or the IP protocol number of the inner network layer (if no mid-layer encapsulation is used). The VET interface sets the other fields in the SEAL header as specified in [I-D.templin-intarea-seal]. 5.5.4. Outer UDP Header Encapsulation Following any mid-layer and/or SEAL encapsulations, VET interfaces that use UDP encapsulation add an outer UDP header. Inclusion of an outer UDP header must be applied uniformly between all neighbors on the VET link. Note that when a VET interface sends a UDP- encapsulated packet to a neighbor that does not recognize the UDP port number, it may receive an ICMP "port unreachable" message. VET interfaces use UDP encapsulation on VET links that may traverse NATs and/or legacy networking gear (e.g., Equal Cost MultiPath (ECMP) routers, Link Aggregation Gateways (LAGs), etc.) that only recognize well-known network layer protocols. When UDP encapsulation is used, the VET interface encapsulates the mid-layer packet in an outer UDP header then sets the UDP port numbers as specified for the outermost mid-layer protocol (e.g., IPsec [RFC3947][RFC3948], etc.) When SEAL [I-D.templin-intarea-seal] is used as the outermost mid- layer protocol, the VET interface sets the UDP destination port number to the value reserved for SEAL and sets the UDP source port number according to whether the next hop neighbor relationship is bidirectional or unidirectional. For bidirectional neighbors, the VET interface sets the UDP source port to a constant value so that return packets will correctly traverse any NATs in the path. For unidirectional neighbors, the VET interface sets the UDP source port to a hash calculated over the inner network layer {destination, source} values or (optionally) over the inner network layer {dest addr, source addr, protocol, dest port, source port} values. The VET interface uses a hash function of its own choosing, but it MUST be consistent in the manner in which the hash is applied. For VET links configured over IPv4 enterprise networks, the VET interface sets the UDP checksum field to zero. For VET links configured over IPv6 enterprise networks, considerations for setting the UDP checksum are discussed in [I-D.ietf-6man-udpzero]. Templin Expires July 23, 2011 [Page 24] Internet-Draft VET January 2011 5.5.5. Outer IP Header Encapsulation Following any mid-layer, SEAL and/or UDP encapsulations, the VET interface adds an outer IP header. Outer IP header construction is the same as specified for ordinary IP encapsulation (e.g., [RFC2003], [RFC2473], [RFC4213], etc.) except that the "TTL/Hop Limit", "Type of Service/Traffic Class" and "Congestion Experienced" values in the inner network layer header are copied into the corresponding fields in the outer IP header. The VET interface also sets the IP protocol number to the appropriate value for the first protocol layer within the encapsulation (e.g., UDP, SEAL, IPsec, etc.). When IPv6 is used as the outer IP protocol, the VET interface sets the flow label value in the outer IPv6 header the same as described in [I-D.carpenter-flow-ecmp]. 5.5.6. Decapsulation When a VET interface receives an encapsulated packet, it retains the outer headers and processes the SEAL header as specified in [I-D.templin-intarea-seal]. Next, if the packet will be forwarded from the receiving VET interface into a forwarding VET interface, the VET node copies the "TTL/Hop Limit", "Type of Service/Traffic Class" and "Congestion Experienced" values in the outer IP header received on the receiving VET interface into the corresponding fields in the outer IP header to be sent over the forwarding VET interface (i.e., the values are transferred between outer headers and *not* copied from the inner network layer header). This is true even if the packet is forwarded out the same VET interface that it arrived on, and necessary to support diagnostic functions (e.g., traceroute) and avoid looping. During decapsulation, when the next-hop is via a non-VET interface, the "Congestion Experienced" value in the outer IP header is copied into the corresponding field in the inner network layer header. 5.6. Mobility and Multihoming Considerations VBRs that travel between distinct enterprise networks must either abandon their PA prefixes that are relative to the "old" network and obtain PA prefixes relative to the "new" network, or somehow coordinate with a "home" network to retain ownership of the prefixes. In the first instance, the VBR would be required to coordinate a network renumbering event on its attached networks using the new PA prefixes [RFC4192][RFC5887]. In the second instance, an adjunct mobility management mechanism is required. VBRs can retain their PI prefixes as they travel between distinct Templin Expires July 23, 2011 [Page 25] Internet-Draft VET January 2011 network points of attachment as long as they continue to refresh their PI prefix to RLOC address mappings with their serving VBG as described in [I-D.templin-iron]. (When the VBR moves far from its serving VBG, it can also select a new VBG in order to maintain optimal routing.) In this way, VBRs can update their PI prefix to RLOC mappings in real time and without requiring an adjunct mobility management mechanism. The VBGs of a multihomed enterprise network participate in a private inner network layer routing protocol instance (e.g., via an interior BGP instance) to accommodate network partitions/merges as well as intra-enterprise mobility events. 5.7. Neighbor Coordination on VET Interfaces using SEAL VET interfaces that use SEAL use the SEAL Control Message Protocol (SCMP) as specified in Section 4.5 of [I-D.templin-intarea-seal] to coordinate reachability, routing information, and mappings between the inner and outer network layer protocols. SCMP directly parallels the IPv6 Neighbor Discovery (ND) [RFC4191][RFC4861] and ICMPv6 [RFC4443] protocols, but operates from within the tunnel and supports operation for any combinations of inner and outer network layer protocols. VET and SEAL are specifically designed for encapsulation of inner network layer payloads over outer IPv4 and IPv6 networks as a link layer. VET interfaces that use SCMP therefore require a new Source/ Target Link-Layer Address Option (S/TLLAO) format that encapsulates IPv4 addresses as shown in Figure 2 and IPv6 addresses as shown in Figure 3: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 2 | Length = 1 | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv4 address (bytes 0 thru 3) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 2: SCMP S/TLLAO Option for IPv4 RLOCs Templin Expires July 23, 2011 [Page 26] Internet-Draft VET January 2011 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 2 | Length = 3 | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv6 address (bytes 0 thru 3) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv6 address (bytes 4 thru 7) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv6 address (bytes 8 thru 11) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv6 address (bytes 12 thru 15) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3: SCMP S/TLLAO Option for IPv6 RLOCs In addition, VET interfaces that use SCMP use a modified version of the Route Information Option (RIO) (see: [RFC4191]) formatted as shown in Figure 4: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 24 | Length | Prefix Length | AF |Prf|Resvd| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Route Lifetime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Prefix (Variable Length) | . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: SCMP Route Information Option Format In this modified format, the VET interface sets the Route Lifetime and Prefix fields in the RIO option the same as specified in [RFC4191]. It then sets the fields in the header as follows: o the 'Type', 'Prf', and 'Resvd' fields are set the same as specified in [RFC4191]. o the 'Length' field is set to 1, 2, or 3 as specified in [RFC4191]. It is instead set to 4 if the 'Prefix Length' is greater than 128 and set to 5 if the 'Prefix Length' is greater than 192 (e.g., in order to accommodate longer prefixes of non-IP protocols). Templin Expires July 23, 2011 [Page 27] Internet-Draft VET January 2011 o the 'Prefix Length' field ranges from 0 to 255. The 'Prefix' field is 0, 8, 16, 24 or 32 octets depending on the Length, and the embedded prefix MAY be up to 255 bits in length. o bits 24 - 26 are used to contain an 'Address Family (AF)' value that indicates the embedded prefix protocol type. This document defines the following values for AF: * 000 - IPv4 * 001 - IPv6 * 010 - OSI/CLNP NSAP The following subsections discuss VET interface neighbor coordination using SCMP: 5.7.1. Router Discovery VET hosts and VBRs can send SCMP Router Solicitation (SRS) messages to one or more VBGs in the PRL to receive solicited SCMP Router Advertisements (SRAs). When an VBG receives an SRS message on a VET interface, it prepares a solicited SRA message. The SRA includes Router Lifetimes, Default Router Preferences, PIOs and any other options/parameters that the VBG is configured to include. If necessary, the VBG also includes Route Information Options (RIOs) formatted as specified above. The VBG finally includes one or more SLLAOs formatted as specified above that encode the IPv6 and/or IPv4 RLOC unicast addresses of its own enterprise-interior interfaces or the enterprise-interior interfaces of other nearby VBGs. 5.7.2. Neighbor Unreachability Detection VET nodes perform Neighbor Unreachability Detection (NUD) on VET interface neighbors by monitoring hints of forward progress enabled by SEAL mechanisms as evidence that a neighbor is reachable. First, when data packets are flowing, the VET node can periodically set the A bit in the SEAL header of data packets to elicit SCMP responses from the neighbor. Secondly, when no data packets are flowing, the VET node can send periodic probes such as SCMP Neighbor Solicitation (SNS) messages for the same purpose. Responsiveness to routing changes is directly related to the delay in detecting that a neighbor has gone unreachable. In order to provide responsiveness comparable to dynamic routing protocols, a reasonably Templin Expires July 23, 2011 [Page 28] Internet-Draft VET January 2011 short neighbor reachable time (e.g., 5sec) SHOULD be used. Additionally, a VET node may receive outer IP ICMP "Destination Unreachable; net / host unreachable" messages from an ER on the path indicating that the path to a neighbor may be failing. The node SHOULD first check the packet-in-error to obtain reasonable assurance that the ICMP message is authentic. If the node receives excessive ICMP unreachable errors through multiple RLOCs associated with the same FIB entry, it SHOULD delete the FIB entry and allow subsequent packets to flow through a different route (e.g., a default route with a VBG as the next hop). 5.7.3. Redirect Function A VET node (i.e., the redirectee) may receive a redirect message when it forwards packets over a VET interface to a neighboring VET node (i.e., the redirector). The redirector will forward the packet and return an SCMP Redirect message if necessary to inform the redirectee of a better next hop. The SCMP Redirect message is formatted the same as for ordinary ICMPv6 redirect messages (see Section 4.5 of [RFC4861]), except that the Destination and Target Address fields are unnecessary and therefore omitted. The format of the SCMP Redirect message is shown in Figure 5 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = 137 | Code = 0 | Checksum | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Options ... +-+-+-+-+-+-+-+-+-+-+-+- Figure 5: SCMP Redirect Message Format The redirector then adds any necessary Options to the Redirect message. It first includes one or more TLLAOs (see above) that include RLOCs corresponding to better next hops. The redirector next includes an RIO that contains a prefix from its FIB that covers the destination address of the original packet. Following the RIO option, the redirector includes any other necessary options (e.g., SEND options) followed by a Redirected Header option containing the leading portion of the packet that triggered the redirect as the final option in the message. The redirector then encapsulates the Redirect message the same as for any other SCMP Templin Expires July 23, 2011 [Page 29] Internet-Draft VET January 2011 message and sends it to the redirectee. When the redirectee receives the Redirect, it first authenticates the message then uses the EID prefix in the RIO with its respective lifetime to update its FIB. The redirectee also caches the IPv4 or IPv6 addresses in TLLAOs as the layer 2 addresses of potential next- hops for the prefix. The redirectee retains the FIB entry created as a result of receipt of an SCMP Redirect until the route lifetime expires, or until the redirected target neighbor becomes unreachable. In this way, RLOC liveness detection parallels IPv6 Neighbor Unreachability Detection. 5.7.3.1. Correspondent Node Redirection When a mobile VET node moves to a new network point of attachment, it leaves short-term forwarding information with its former network point of attachment. Thereafter, any existing correspondents that attempt to contact the mobile node via the former network point of attachment will be redirected to the new network point of attachment. In this way, mobile VET nodes need not inform correspondents of a mobility event, since the correspondents will soon receive redirects from the network. 5.8. Neighbor Coordination on VET Interfaces using IPsec VET interfaces that use IPsec encapsulation use the Internet Key Exchange protocol, version 2 (IKEv2) [RFC4306] to manage security association setup and maintenance. IKEv2 provides a logical equivalent of the SCMP in terms of VET interface neighbor coordinations; for example, IKEv2 also provides mechanisms for redirection [RFC5685] and mobility [RFC4555]. IPsec additionally provides an extended Identification field and integrity check vector; these features allow IPsec to utilize outer IP fragmentation and reassembly with less risk of exposure to data corruption due to reassembly misassociations. On the other hand, IPsec entails the use of symmetric security associations and hence may not be appropriate to all enterprise network use cases. 5.9. Multicast 5.9.1. Multicast over (Non)Multicast Enterprise Networks Whether or not the underlying enterprise network supports a native multicasting service, the VET node can act as an inner network layer IGMP/MLD proxy [RFC4605] on behalf of its attached edge networks and Templin Expires July 23, 2011 [Page 30] Internet-Draft VET January 2011 convey its multicast group memberships over the VET interface to a VBG acting as a multicast router. Its inner network layer multicast transmissions will therefore be encapsulated in outer headers with the unicast address of the VBG as the destination. 5.9.2. Multicast Over Multicast-Capable Enterprise Networks In multicast-capable enterprise networks, ERs provide an enterprise- wide multicasting service (e.g., Simplified Multicast Forwarding (SMF) [I-D.ietf-manet-smf], Protocol Independent Multicast (PIM) routing, Distance Vector Multicast Routing Protocol (DVMRP) routing, etc.) over their enterprise-interior interfaces such that outer IP multicast messages of site-scope or greater scope will be propagated across the enterprise network. For such deployments, VET nodes can optionally provide a native inner multicast/broadcast capability over their VET interfaces through mapping of the inner multicast address space to the outer multicast address space. In that case, operation of link-or greater-scoped inner multicasting services (e.g., a link- scoped neighbor discovery protocol) over the VET interface is available, but SHOULD be used sparingly to minimize enterprise-wide flooding. VET nodes encapsulate inner multicast messages sent over the VET interface in any mid-layer headers (e.g., UDP, SEAL, IPsec, etc.) followed by an outer IP header with a site-scoped outer IP multicast address as the destination. For the case of IPv6 and IPv4 as the inner/outer protocols (respectively), [RFC2529] provides mappings from the IPv6 multicast address space to a site-scoped IPv4 multicast address space (for other encapsulations, mappings are established through administrative configuration or through an unspecified alternate static mapping). Multicast mapping for inner multicast groups over outer IP multicast groups can be accommodated, e.g., through VET interface snooping of inner multicast group membership and routing protocol control messages. To support inner-to-outer multicast address mapping, the VET interface acts as a virtual outer IP multicast host connected to its underlying interfaces. When the VET interface detects that an inner multicast group joins or leaves, it forwards corresponding outer IP multicast group membership reports on an underlying interface over which the VET interface is configured. If the VET node is configured as an outer IP multicast router on the underlying interfaces, the VET interface forwards locally looped-back group membership reports to the outer IP multicast routing process. If the VET node is configured as a simple outer IP multicast host, the VET interface instead forwards actual group membership reports (e.g., IGMP messages) directly over an underlying interface. Templin Expires July 23, 2011 [Page 31] Internet-Draft VET January 2011 Since inner multicast groups are mapped to site-scoped outer IP multicast groups, the VET node MUST ensure that the site-scoped outer IP multicast messages received on the underlying interfaces for one VET interface do not "leak out" to the underlying interfaces of another VET interface. This is accommodated through normal site- scoped outer IP multicast group filtering at enterprise network boundaries. 5.10. Service Discovery VET nodes can perform enterprise-wide service discovery using a suitable name-to-address resolution service. Examples of flooding- based services include the use of LLMNR [RFC4795] over the VET interface or multicast DNS (mDNS) [I-D.cheshire-dnsext-multicastdns] over an underlying interface. More scalable and efficient service discovery mechanisms (e.g., anycast) are for further study. 5.11. VET Link Partitioning A VET link can be partitioned into multiple distinct logical groupings. In that case, each partition configures its own distinct 'PRLNAME' (e.g., 'isatapv2.zone1.example.com', 'isatapv2.zone2.example.com', etc.). VBGs can further create multiple IP subnets within a partition, e.g., by sending SRAs with PIOs containing different IP prefixes to different groups of VET hosts. VBGs can identify subnets, e.g., by examining RLOC prefixes, observing the enterprise-interior interfaces over which SRSs are received, etc. In the limiting case, VBGs can advertise a unique set of IP prefixes to each VET host such that each host belongs to a different subnet (or set of subnets) on the VET interface. 5.12. VBG Prefix State Recovery VBGs retain explicit state that tracks the inner network layer prefixes delegated to VBRs connected to the VET link, e.g., so that packets are delivered to the correct VBRs. When a VBG loses some or all of its state (e.g., due to a power failure), client VBRs must refresh the VBG's state so that packets can be forwarded over correct routes. 5.13. Support for Legacy ISATAP Services VBGs can support legacy ISATAP services according to the specifications in [RFC5214]. In particular, VBGs can configure legacy ISATAP interfaces and VET interfaces over the same sets of Templin Expires July 23, 2011 [Page 32] Internet-Draft VET January 2011 underlying interfaces as long as the PRLs and IPv6 prefixes associated with the ISATAP/VET interfaces are distinct. Legacy ISATAP hosts acquire addresses and/or prefixes in the same manner and using the same mechanisms as described for VET hosts in Section 4.4 above. 6. IANA Considerations There are no IANA considerations for this document. 7. Security Considerations Security considerations for MANETs are found in [RFC2501]. The security considerations found in [RFC2529][RFC5214][I-D.nakibly-v6ops-tunnel-loops] also apply to VET. SEND [RFC3971] and/or IPsec [RFC4301] can be used in environments where attacks on the neighbor coordination protocol are possible. SEAL [I-D.templin-intarea-seal] provides a per-packet identification that can be used to detect source address spoofing. Rogue neighbor coordination messages with spoofed RLOC source addresses can consume network resources and cause VET nodes to perform extra work. Nonetheless, VET nodes SHOULD NOT "blacklist" such RLOCs, as that may result in a denial of service to the RLOCs' legitimate owners. VBRs and VBGs observe the recommendations for network ingress filtering [RFC2827]. 8. Related Work Brian Carpenter and Cyndi Jung introduced the concept of intra-site automatic tunneling in [RFC2529]; this concept was later called: "Virtual Ethernet" and investigated by Quang Nguyen under the guidance of Dr. Lixia Zhang. Subsequent works by these authors and their colleagues have motivated a number of foundational concepts on which this work is based. Telcordia has proposed DHCP-related solutions for MANETs through the CECOM MOSAIC program. The Naval Research Lab (NRL) Information Technology Division uses Templin Expires July 23, 2011 [Page 33] Internet-Draft VET January 2011 DHCP in their MANET research testbeds. Security concerns pertaining to tunneling mechanisms are discussed in [I-D.ietf-v6ops-tunnel-security-concerns]. Default router and prefix information options for DHCPv6 are discussed in [I-D.droms-dhc-dhcpv6-default-router]. An automated IPv4 prefix delegation mechanism is proposed in [I-D.ietf-dhc-subnet-alloc]. RLOC prefix delegation for enterprise-edge interfaces is discussed in [I-D.clausen-manet-autoconf-recommendations]. MANET link types are discussed in [I-D.clausen-manet-linktype]. The LISP proposal [I-D.ietf-lisp] examines encapsulation/ decapsulation issues and other aspects of tunneling. Various proposals within the IETF have suggested similar mechanisms. 9. Acknowledgements The following individuals gave direct and/or indirect input that was essential to the work: Jari Arkko, Teco Boot, Emmanuel Bacelli, Fred Baker, James Bound, Scott Brim, Brian Carpenter, Thomas Clausen, Claudiu Danilov, Chris Dearlove, Remi Despres, Gert Doering, Ralph Droms, Washam Fan, Dino Farinacci, Vince Fuller, Thomas Goff, David Green, Joel Halpern, Bob Hinden, Sascha Hlusiak, Sapumal Jayatissa, Dan Jen, Darrel Lewis, Tony Li, Joe Macker, David Meyer, Gabi Nakibly, Thomas Narten, Pekka Nikander, Dave Oran, Alexandru Petrescu, Mark Smith, John Spence, Jinmei Tatuya, Dave Thaler, Mark Townsley, Ole Troan, Michaela Vanderveen, Robin Whittle, James Woodyatt, Lixia Zhang, and others in the IETF AUTOCONF and MANET working groups. Many others have provided guidance over the course of many years. 10. Contributors The following individuals have contributed to this document: Eric Fleischman (eric.fleischman@boeing.com) Thomas Henderson (thomas.r.henderson@boeing.com) Steven Russert (steven.w.russert@boeing.com) Seung Yi (seung.yi@boeing.com) Templin Expires July 23, 2011 [Page 34] Internet-Draft VET January 2011 Ian Chakeres (ian.chakeres@gmail.com) contributed to earlier versions of the document. Jim Bound's foundational work on enterprise networks provided significant guidance for this effort. We mourn his loss and honor his contributions. 11. References 11.1. Normative References [I-D.templin-intarea-seal] Templin, F., "The Subnetwork Encapsulation and Adaptation Layer (SEAL)", draft-templin-intarea-seal-26 (work in progress), January 2011. [RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791, September 1981. [RFC0792] Postel, J., "Internet Control Message Protocol", STD 5, RFC 792, September 1981. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2131] Droms, R., "Dynamic Host Configuration Protocol", RFC 2131, March 1997. [RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 2460, December 1998. [RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering: Defeating Denial of Service Attacks which employ IP Source Address Spoofing", BCP 38, RFC 2827, May 2000. [RFC3118] Droms, R. and W. Arbaugh, "Authentication for DHCP Messages", RFC 3118, June 2001. [RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C., and M. Carney, "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)", RFC 3315, July 2003. [RFC3633] Troan, O. and R. Droms, "IPv6 Prefix Options for Dynamic Host Configuration Protocol (DHCP) version 6", RFC 3633, December 2003. [RFC3971] Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure Templin Expires July 23, 2011 [Page 35] Internet-Draft VET January 2011 Neighbor Discovery (SEND)", RFC 3971, March 2005. [RFC3972] Aura, T., "Cryptographically Generated Addresses (CGA)", RFC 3972, March 2005. [RFC4191] Draves, R. and D. Thaler, "Default Router Preferences and More-Specific Routes", RFC 4191, November 2005. [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, February 2006. [RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification", RFC 4443, March 2006. [RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman, "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861, September 2007. [RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, September 2007. [RFC5342] Eastlake, D., "IANA Considerations and IETF Protocol Usage for IEEE 802 Parameters", BCP 141, RFC 5342, September 2008. 11.2. Informative References [CATENET] Pouzin, L., "A Proposal for Interconnecting Packet Switching Networks", May 1974. [I-D.carpenter-flow-ecmp] Carpenter, B. and S. Amante, "Using the IPv6 flow label for equal cost multipath routing and link aggregation in tunnels", draft-carpenter-flow-ecmp-03 (work in progress), October 2010. [I-D.cheshire-dnsext-multicastdns] Cheshire, S. and M. Krochmal, "Multicast DNS", draft-cheshire-dnsext-multicastdns-13 (work in progress), January 2011. [I-D.clausen-manet-autoconf-recommendations] Clausen, T. and U. Herberg, "MANET Router Configuration Recommendations", draft-clausen-manet-autoconf-recommendations-00 (work in progress), February 2009. Templin Expires July 23, 2011 [Page 36] Internet-Draft VET January 2011 [I-D.clausen-manet-linktype] Clausen, T., "The MANET Link Type", draft-clausen-manet-linktype-00 (work in progress), October 2008. [I-D.droms-dhc-dhcpv6-default-router] Droms, R. and T. Narten, "Default Router and Prefix Advertisement Options for DHCPv6", draft-droms-dhc-dhcpv6-default-router-00 (work in progress), March 2009. [I-D.ietf-6man-udpzero] Fairhurst, G. and M. Westerlund, "IPv6 UDP Checksum Considerations", draft-ietf-6man-udpzero-02 (work in progress), October 2010. [I-D.ietf-dhc-subnet-alloc] Johnson, R., Kumarasamy, J., Kinnear, K., and M. Stapp, "Subnet Allocation Option", draft-ietf-dhc-subnet-alloc-11 (work in progress), May 2010. [I-D.ietf-grow-va] Francis, P., Xu, X., Ballani, H., Jen, D., Raszuk, R., and L. Zhang, "FIB Suppression with Virtual Aggregation", draft-ietf-grow-va-03 (work in progress), August 2010. [I-D.ietf-lisp] Farinacci, D., Fuller, V., Meyer, D., and D. Lewis, "Locator/ID Separation Protocol (LISP)", draft-ietf-lisp-09 (work in progress), October 2010. [I-D.ietf-manet-smf] Macker, J. and S. Team, "Simplified Multicast Forwarding", draft-ietf-manet-smf-10 (work in progress), March 2010. [I-D.ietf-v6ops-tunnel-security-concerns] Krishnan, S., Thaler, D., and J. Hoagland, "Security Concerns With IP Tunneling", draft-ietf-v6ops-tunnel-security-concerns-04 (work in progress), October 2010. [I-D.jen-apt] Jen, D., Meisel, M., Massey, D., Wang, L., Zhang, B., and L. Zhang, "APT: A Practical Transit Mapping Service", draft-jen-apt-01 (work in progress), November 2007. [I-D.nakibly-v6ops-tunnel-loops] Nakibly, G. and F. Templin, "Routing Loop Attack using Templin Expires July 23, 2011 [Page 37] Internet-Draft VET January 2011 IPv6 Automatic Tunnels: Problem Statement and Proposed Mitigations", draft-nakibly-v6ops-tunnel-loops-03 (work in progress), August 2010. [I-D.russert-rangers] Russert, S., Fleischman, E., and F. Templin, "RANGER Scenarios", draft-russert-rangers-05 (work in progress), July 2010. [I-D.templin-iron] Templin, F., "The Internet Routing Overlay Network (IRON)", draft-templin-iron-17 (work in progress), January 2011. [IEN48] Cerf, V., "The Catenet Model for Internetworking", July 1978. [RASADV] Microsoft, "Remote Access Server Advertisement (RASADV) Protocol Specification", October 2008. [RFC0994] International Organization for Standardization (ISO) and American National Standards Institute (ANSI), "Final text of DIS 8473, Protocol for Providing the Connectionless- mode Network Service", RFC 994, March 1986. [RFC1035] Mockapetris, P., "Domain names - implementation and specification", STD 13, RFC 1035, November 1987. [RFC1070] Hagens, R., Hall, N., and M. Rose, "Use of the Internet as a subnetwork for experimentation with the OSI network layer", RFC 1070, February 1989. [RFC1122] Braden, R., "Requirements for Internet Hosts - Communication Layers", STD 3, RFC 1122, October 1989. [RFC1753] Chiappa, J., "IPng Technical Requirements Of the Nimrod Routing and Addressing Architecture", RFC 1753, December 1994. [RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G., and E. Lear, "Address Allocation for Private Internets", BCP 5, RFC 1918, February 1996. [RFC1955] Hinden, R., "New Scheme for Internet Routing and Addressing (ENCAPS) for IPNG", RFC 1955, June 1996. [RFC2003] Perkins, C., "IP Encapsulation within IP", RFC 2003, October 1996. Templin Expires July 23, 2011 [Page 38] Internet-Draft VET January 2011 [RFC2132] Alexander, S. and R. Droms, "DHCP Options and BOOTP Vendor Extensions", RFC 2132, March 1997. [RFC2473] Conta, A. and S. Deering, "Generic Packet Tunneling in IPv6 Specification", RFC 2473, December 1998. [RFC2491] Armitage, G., Schulter, P., Jork, M., and G. Harter, "IPv6 over Non-Broadcast Multiple Access (NBMA) networks", RFC 2491, January 1999. [RFC2501] Corson, M. and J. Macker, "Mobile Ad hoc Networking (MANET): Routing Protocol Performance Issues and Evaluation Considerations", RFC 2501, January 1999. [RFC2529] Carpenter, B. and C. Jung, "Transmission of IPv6 over IPv4 Domains without Explicit Tunnels", RFC 2529, March 1999. [RFC2775] Carpenter, B., "Internet Transparency", RFC 2775, February 2000. [RFC3819] Karn, P., Bormann, C., Fairhurst, G., Grossman, D., Ludwig, R., Mahdavi, J., Montenegro, G., Touch, J., and L. Wood, "Advice for Internet Subnetwork Designers", BCP 89, RFC 3819, July 2004. [RFC3927] Cheshire, S., Aboba, B., and E. Guttman, "Dynamic Configuration of IPv4 Link-Local Addresses", RFC 3927, May 2005. [RFC3947] Kivinen, T., Swander, B., Huttunen, A., and V. Volpe, "Negotiation of NAT-Traversal in the IKE", RFC 3947, January 2005. [RFC3948] Huttunen, A., Swander, B., Volpe, V., DiBurro, L., and M. Stenberg, "UDP Encapsulation of IPsec ESP Packets", RFC 3948, January 2005. [RFC4192] Baker, F., Lear, E., and R. Droms, "Procedures for Renumbering an IPv6 Network without a Flag Day", RFC 4192, September 2005. [RFC4193] Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast Addresses", RFC 4193, October 2005. [RFC4213] Nordmark, E. and R. Gilligan, "Basic Transition Mechanisms for IPv6 Hosts and Routers", RFC 4213, October 2005. [RFC4271] Rekhter, Y., Li, T., and S. Hares, "A Border Gateway Templin Expires July 23, 2011 [Page 39] Internet-Draft VET January 2011 Protocol 4 (BGP-4)", RFC 4271, January 2006. [RFC4301] Kent, S. and K. Seo, "Security Architecture for the Internet Protocol", RFC 4301, December 2005. [RFC4306] Kaufman, C., "Internet Key Exchange (IKEv2) Protocol", RFC 4306, December 2005. [RFC4548] Gray, E., Rutemiller, J., and G. Swallow, "Internet Code Point (ICP) Assignments for NSAP Addresses", RFC 4548, May 2006. [RFC4555] Eronen, P., "IKEv2 Mobility and Multihoming Protocol (MOBIKE)", RFC 4555, June 2006. [RFC4605] Fenner, B., He, H., Haberman, B., and H. Sandick, "Internet Group Management Protocol (IGMP) / Multicast Listener Discovery (MLD)-Based Multicast Forwarding ("IGMP/MLD Proxying")", RFC 4605, August 2006. [RFC4795] Aboba, B., Thaler, D., and L. Esibov, "Link-local Multicast Name Resolution (LLMNR)", RFC 4795, January 2007. [RFC4852] Bound, J., Pouffary, Y., Klynsma, S., Chown, T., and D. Green, "IPv6 Enterprise Network Analysis - IP Layer 3 Focus", RFC 4852, April 2007. [RFC4903] Thaler, D., "Multi-Link Subnet Issues", RFC 4903, June 2007. [RFC4941] Narten, T., Draves, R., and S. Krishnan, "Privacy Extensions for Stateless Address Autoconfiguration in IPv6", RFC 4941, September 2007. [RFC5214] Templin, F., Gleeson, T., and D. Thaler, "Intra-Site Automatic Tunnel Addressing Protocol (ISATAP)", RFC 5214, March 2008. [RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF for IPv6", RFC 5340, July 2008. [RFC5569] Despres, R., "IPv6 Rapid Deployment on IPv4 Infrastructures (6rd)", RFC 5569, January 2010. [RFC5685] Devarapalli, V. and K. Weniger, "Redirect Mechanism for the Internet Key Exchange Protocol Version 2 (IKEv2)", RFC 5685, November 2009. Templin Expires July 23, 2011 [Page 40] Internet-Draft VET January 2011 [RFC5720] Templin, F., "Routing and Addressing in Networks with Global Enterprise Recursion (RANGER)", RFC 5720, February 2010. [RFC5887] Carpenter, B., Atkinson, R., and H. Flinck, "Renumbering Still Needs Work", RFC 5887, May 2010. [RFC5969] Townsley, W. and O. Troan, "IPv6 Rapid Deployment on IPv4 Infrastructures (6rd) -- Protocol Specification", RFC 5969, August 2010. Appendix A. Duplicate Address Detection (DAD) Considerations A priori uniqueness determination (also known as "pre-service DAD") for an RLOC assigned on an enterprise-interior interface would require either flooding the entire enterprise network or somehow discovering a link in the network on which a node that configures a duplicate address is attached and performing a localized DAD exchange on that link. But, the control message overhead for such an enterprise-wide DAD would be substantial and prone to false-negatives due to packet loss and intermittent connectivity. An alternative to pre-service DAD is to autoconfigure pseudo-random RLOCs on enterprise-interior interfaces and employ a passive in-service DAD (e.g., one that monitors routing protocol messages for duplicate assignments). Pseudo-random IPv6 RLOCs can be generated with mechanisms such as CGAs, IPv6 privacy addresses, etc. with very small probability of collision. Pseudo-random IPv4 RLOCs can be generated through random assignment from a suitably large IPv4 prefix space. Consistent operational practices can assure uniqueness for VBG- aggregated addresses/prefixes, while statistical properties for pseudo-random address self-generation can assure uniqueness for the RLOCs assigned on an ER's enterprise-interior interfaces. Still, an RLOC delegation authority should be used when available, while a passive in-service DAD mechanism should be used to detect RLOC duplications when there is no RLOC delegation authority. Appendix B. Anycast Services Some of the IPv4 addresses that appear in the Potential Router List may be anycast addresses, i.e., they may be configured on the VET interfaces of multiple VBRs/VBGs. In that case, each VET router interface that configures the same anycast address must exhibit equivalent outward behavior. Templin Expires July 23, 2011 [Page 41] Internet-Draft VET January 2011 Use of an anycast address as the IP destination address of tunneled packets can have subtle interactions with tunnel path MTU and neighbor discovery. For example, if the initial fragments of a fragmented tunneled packet with an anycast IP destination address are routed to different egress tunnel endpoints than the remaining fragments, the multiple endpoints will be left with incomplete reassembly buffers. This issue can be mitigated by ensuring that each egress tunnel endpoint implements a proactive reassembly buffer garbage collection strategy. Additionally, ingress tunnel endpoints that send packets with an anycast IP destination address must use the minimum path MTU for all egress tunnel endpoints that configure the same anycast address as the tunnel MTU. Finally, ingress tunnel endpoints should treat ICMP unreachable messages from a router within the tunnel as at most a weak indication of neighbor unreachability, since the failures may only be transient and a different path to an alternate anycast router quickly selected through reconvergence of the underlying routing protocol. Use of an anycast address as the IP source address of tunneled packets can lead to more serious issues. For example, when the IP source address of a tunneled packet is anycast, ICMP messages produced by routers within the tunnel might be delivered to different ingress tunnel endpoints than the ones that produced the packets. In that case, functions such as path MTU discovery and neighbor unreachability detection may experience non-deterministic behavior that can lead to communications failures. Additionally, the fragments of multiple tunneled packets produced by multiple ingress tunnel endpoints may be delivered to the same reassembly buffer at a single egress tunnel endpoint. In that case, data corruption may result due to fragment misassociation during reassembly. In view of these considerations, VBGs that configure an anycast address should also configure one or more unicast addresses from the Potential Router List; they should further accept tunneled packets destined to any of their anycast or unicast addresses, but should send tunneled packets using a unicast address as the source address. Appendix C. Change Log (Note to RFC editor - this section to be removed before publication as an RFC.) Changes from -14 to -15: o new insights into default route configuration and next-hop determination Templin Expires July 23, 2011 [Page 42] Internet-Draft VET January 2011 Changes from -13 to -14: o fixed Idnits Changes from -12 to -13: o Changed "VGL" *back* to "PRL" o More changes for multi-protocol support o Changes to Redirect function Changes from -11 to -12: o Major section rearrangement o Changed "PRL" to "VGL" o Brought back text that was lost in the -10 to -11 transition Changes from -10 to -11: o Major changes with significant simplifications o Now support stateless PD using 6rd mechanisms o SEAL Control Message Protocol (SCMP) used instead of ICMPv6 o Multi-protocol support including IPv6, IPv4, OSI/CLNP, etc. Changes from -09 to -10: o Changed "enterprise" to "enterprise network" throughout o dropped "inner IP", since inner layer may be non-IP o TODO - convert "IPv6 ND" to SEAL SCMP messages so that control messages remain *within* the tunnel interface instead of being exposed to the inner network layer protocol engine. Changes from -08 to -09: o Expanded discussion of encapsulation/decapsulation procedures o cited IRON Changes from -07 to -08: Templin Expires July 23, 2011 [Page 43] Internet-Draft VET January 2011 o Specified the approach to global mapping using virtual aggregation and BGP Changes from -06 to -07: o reworked redirect function o created new section on VET interface encapsulation o clarifications on nexthop selection o fixed several bugs Changed from -05 to -06: o reworked VET interface ND o anycast clarifications Changes from -03 to -04: o security consideration clarifications Changes from -02 to -03: o security consideration clarifications o new PRLNAME for VET is "isatav2.example.com" o VET now uses SEAL natively o EBGs can support both legacy ISATAP and VET over the same underlying interfaces. Changes from -01 to -02: o Defined CGA and privacy address configuration on VET interfaces o Interface identifiers added to routing protocol control messages for link-layer multiplexing Changes from -00 to -01: o Section 4.1 clarifications on link-local assignment and RLOC autoconfiguration. o Appendix B clarifications on Weak End System Model Templin Expires July 23, 2011 [Page 44] Internet-Draft VET January 2011 Changes from RFC5558 to -00: o New appendix on RLOC configuration on VET interfaces. Author's Address Fred L. Templin (editor) Boeing Research & Technology P.O. Box 3707 MC 7L-49 Seattle, WA 98124 USA Email: fltemplin@acm.org Templin Expires July 23, 2011 [Page 45]