Internet Engineering Task Force Yimin Shen Internet-Draft Zhaohui Zhang Intended status: Standards Track Juniper Networks Expires: August 6, 2020 February 3, 2020 Point-to-Multipoint Transport Using Chain Replication in Segment Routing draft-shen-spring-p2mp-transport-chain-00 Abstract This document specifies a point-to-multipoint (P2MP) transport mechanism based on chain replication. It can be used in segment routing to achieve traffic optimization. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on August 6, 2020. Copyright Notice Copyright (c) 2020 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 1] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Specification of Requirements . . . . . . . . . . . . . . . . 3 3. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 3 4. P2MP Transport Using Chain Replication . . . . . . . . . . . 3 4.1. Bud Segment . . . . . . . . . . . . . . . . . . . . . . . 4 4.2. P2MP Chain . . . . . . . . . . . . . . . . . . . . . . . 6 4.3. Example . . . . . . . . . . . . . . . . . . . . . . . . . 7 5. Path Computation for P2MP Chains . . . . . . . . . . . . . . 8 6. IGP and BGP-LS Extensions for Bud Segment . . . . . . . . . . 9 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 9 8. Security Considerations . . . . . . . . . . . . . . . . . . . 9 9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 9 10. References . . . . . . . . . . . . . . . . . . . . . . . . . 10 10.1. Normative References . . . . . . . . . . . . . . . . . . 10 10.2. Informative References . . . . . . . . . . . . . . . . . 10 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10 1. Introduction The Segment Routing Architecture [RFC8402] describes segment routing (SR) and its instantiation in two data planes, i.e. MPLS and IPv6. In SR, point-to-multipoint (P2MP) transport is currently achieved by using ingress replication, where a point-to-point (P2P) SR tunnel is constructed from a root node to each leaf node, and every ingress packet is replicated and sent via a bundle of such P2P SR tunnels to all the leaf nodes. Although this approach provides P2MP reachability, it does not consider traffic optimization across the tunnels, as the path of each tunnel is computed or decided independently. An alternative approach would be to use P2MP-tree based transport. Such approach can achieve maximum traffic optimization, but it relies a controller or path computation element (PCE) to dynamically provision and manage "replication segments" on branch nodes. The replication segments are essentially per-P2MP-tree (i.e. per-tunnel) state on transit routers. Therefore, this approach is not fully aligned with SR's principles of single-point (i.e. ingress router) provisioning and stateless core. This document introduces a new solution for P2MP transport in SR, based on "chain replication". In this solution, P2MP transport is achieved by constructing a set of "P2MP chain tunnels" (or simply "P2MP chains") from a root node to leaf nodes. Each P2MP chain is a tunnel with a leaf node at the tail end and some transit leaf nodes along the path, resembling a chain. A transit leaf node replicates a packet only once for local processing off the chain, and forwards the Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 2] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 original packet down the chain. The root node replicates and sends packets via the set of P2MP chains to all the leaf nodes. As a P2MP chain can reach multiple leaf nodes, it is considered to be more efficient than the multiple P2P tunnels which would be needed in ingress replication to reach these leaf nodes. Compared with ingress replication and the P2MP-tree based approach, this solution provides a middle ground by achieving a certain level of traffic optimization, while aligning with the fundamental principles of SR, including single-point provisioning and stateless core. The solution can be used to improve P2MP transport efficiency in general, and to achieve maximum traffic optimization in certain types of topologies. 2. Specification of Requirements The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119] and [RFC8174]. 3. Applicability The P2MP transport mechanism in this document is generally applicable to all networks. However, it benefits more for certain types of topologies than for others. These topologies include ring topologies, linear topologies, topologies with leaf nodes concentrated in geographical sites which can be modeled as leaf groups, etc. The mechanism is transparent to all transit routers. Leaf nodes intended to take advantage of the mechanism will need to support the new forwarding behavior specified in this document. For other leaf nodes, the mechanism has a backward compatibility to allow them to be reached by P2P tunnels using ingress replication. Path computation and P2MP chain construction will need to be supported by a controller or root nodes, depending on where they are performed. The mechanism is applicable to both SR-MPLS [RFC8660] and SRv6 [SRv6-SRH], [SRv6-Programming]. 4. P2MP Transport Using Chain Replication In this document, a P2MP transport scheme associated with a root node and a set of leaf nodes is denoted as {root node, leaf nodes}. It is achieved by using a bundle of P2MP chains covering all the leaf nodes. Each P2MP chain is a tunnel starting from the root node and reaching one or multiple leaf nodes along the path. The tail-end node of the P2MP chain is a leaf node, called a "tail-end" leaf node. Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 3] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 Each leaf node traversed by the P2MP chain is called a "transit" leaf node. As a special case, a P2MP chain may have no transit leaf node, but only a tail-end leaf node, essentially becoming a P2P tunnel of ingress replication. R ------ R1 ------ R2 ------ L1 ------ R3 ------ L2 ------ L3 R : root node Li : leaf node Ri : transit router Figure 1 A tail-end leaf node and a transit leaf nodes have different behaviors when processing a received packet. In particular, a tail- end leaf node processes the packet as a normal receiver. A transit leaf node not only processes the packet as a receiver, but also forwards it downstream along the P2MP chain, hence acting as a "bud node". To achieve this, the transit leaf node needs to replicate the packet, producing two packets, one for forwarding and the other for local processing. Such packet replication happens on every transit leaf node along a P2MP chain. Therefore, it is called "chain replication". This document introduces a new type of segments, called "bud segments", to facilitate the above packet processing on leaf nodes. The segment ID (SID) of a bud segment is a "bud-SID". 4.1. Bud Segment On a leaf node, a bud segment represents the following instructions for forwarding hardware to execute on a received packet P. They apply when the active SID of the packet P is the bud-SID of this bud segment. [1] Detect whether this leaf node is a transit or tail-end leaf node, based on whether the bud-SID is the last SID of a P2MP chain. [2] If this is a transit leaf node, replicate the packet to produce a copy P1. [2.1] For P, perform a NEXT operation on the bud-SID, make the next SID active, and forward the packet based on that SID. Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 4] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 [2.2] For P1, perform a sequence of NEXT operations on the bud- SID and all the subsequent SIDs of the P2MP chain, and process the packet locally. [3] If this is a tail-end leaf node, perform a NEXT operation on the bud-SID for P, and process the packet locally. In [2.2], when the transit leaf node processes P1 locally, all the SIDs of the P2MP chain are not useful. Hence, they are removed before the processing. Bud segments are global segments of leaf nodes. They are routable segments via topological shortest-paths. Only one bud segment is needed per leaf node, and per SR-MPLS or SRv6. Bud-SIDs are allocated from SRGB (SR global block). In SR-MPLS, bud-SIDs are labels. In SRv6, bud-SIDs are IPv6 addresses explicitly associated with bud segments. Therefore, the above instructions [1] to [3] are achieved in different ways in SR- MPLS and SRv6: (a) In SR-MPLS, there are two cases: (a.1) The packet should have no service label, but only P2MP chain labels in MPLS header. In [1], the bud segment SHOULD detect whether the leaf node is a transit or tail-end leaf node based on the S-bit (bottom of stack) of the bud-SID label. If the S-bit is 0, the leaf node is a transit leaf node. If the S-bit is 1, it is a tail-end leaf node. In [2.2], the bud segment SHOULD simply pop the entire MPLS header. (a.2) The packet may have service label(s) after P2MP chain labels in MPLS header, e.g. a bridge domain label, a source Ethernet segment label, etc. In this case, the bud segment MUST have a way to identify the position of the last P2MP chain label. This document introduces an "end-of-chain" (EoC) label to facilitate the process. An EoC label is a label which is known to all root nodes and leaf nodes in a network. It MUST have a globally common value, via configuration on these nodes. When a root node constructs an MPLS header for a packet, the EoC label MUST be pushed immediately before P2MP chain labels, making it the next label after the last P2MP chain label. Thus, in [1], the bud segment SHOULD detect whether the leaf node is a transit or tail-end leaf node based on whether the next label in the current MPLS header is the EoC label. If so, the leaf node is a tail-end leaf node. Otherwise, it is a transit leaf node. In [2.2], the bud segment SHOULD pop labels until the EoC label is popped. In [3], the bud segment SHOULD Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 5] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 pop the bud-SID label and the next label, which is the EoC label. (b) In SRv6, the packet is encapsulated with an outer IPv6 header corresponding to the P2MP chain, optionally followed by a segment routing header (SRH) containing the SIDs of the P2MP chain, and followed by an inner header (of IPv4, IPv6, MPLS, layer-2, etc.) associated with a service. In [1], the bud segment SHOULD detect whether it is the last P2MP chain SID based on the SRH. If the SRH does not exist or the Segments Left in the SRH is 0, the leaf node is a tail-end leaf node. Otherwise, it is a transit leaf node. In [2.2] and [3], the bud segment SHOULD simply remove the outer IPv6 header and the SRH (if any), and leave the packet with the inner header to local processing. Bud segments are shared by all P2MP transport schemes, i.e. all combinations of {root node, leaf nodes}. A leaf node SHOULD advertise a bud segment for SR-MPLS, if its forwarding hardware supports the above SR-MPLS processing. Likewise, it SHOULD advertise a bud segment for SRv6, if its forwarding hardware supports the above SRv6 processing. The advertisement may be via IGP (ISIS, OSPF) or BGP-LS. The advertisement allows the leaf node to be considered on a P2MP chain. If a leaf node does not advertise a bud segment, it MUST be reached via a P2P tunnel using ingress replication. Bud segments are generic purpose segments. They may also be used in cases other than P2MP transport, such as traffic monitoring. These use cases are out of the scope of this document. 4.2. P2MP Chain Construction of P2MP chains for a P2MP transport scheme is performed by a controller or a root node based on path computation (Section 5). The path of a P2MP chain is a single path traversing one or multiple transit leaf nodes and terminating at a tail-end leaf node. Between the root node and the first transit leaf node, and between two consecutive leaf nodes, there may be none, one, or multiple transit routers. The path is then translated to a SID list to be programmed on the root node. In the SID list, each transit leaf node has its bud-SID in a corresponding position. Given a P2MP chain to a set of leaf nodes in the order of L1, L2, ..., Ln, the SID list may be represented as: , bud-SID of L1, ..., , bud-SID of Li, ..., , Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 6] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 Where: o is the sub-path from the root node to L1. o is the sub-path from Li-1 to Li. o Ln's bud-SID is the last SID of the list, if the sub-path from Ln-1 to Ln is partial or empty, or if an EoC label is needed in SR-MPLS. It is optional in other cases. The above sub-paths are regular point-to-point paths. The SIDs in the sub-paths are regular SIDs, such as adjacency-SIDs, node-SIDs, binding-SIDs, etc. There is no SID specific to the given P2MP chain. A sub-path from Li-1 to Li may have an empty SID list, if the sub- path takes the shortest path indicated by the bud-SID of Li. The root node then uses the SID list in packet encapsulation. Note that in the SR-MPLS case where an EoC label is needed, the EoC label SHOULD be pushed to an MPLS header, before the SID list is pushed. 4.3. Example In the following example, P2MP transport is needed from the root node R, to leaf nodes L1, L2, L3 and L4. R ------ R1 -------------------- R2 ------- L1 | | / | | / | | / R3 -------------------- R4 ------- L2 | | | | | | R5 -------------------- R6 ------- L3 | | / | | / | | / R7 -------------------- R8 ------- L4 Figure 2 Path computation results in two P2MP chains: P2MP chain 1: Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 7] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 Path: R -> R1 -> R2 -> L1 -> R4 -> L2, where L1 is a transit leaf node, and L2 is the tail-end leaf node. Assuming that the sub-path L1 -> R4 -> L2 matches the shortest path from L1 to L2, the bud-SID of L2 is used to represent this sub-path. The segment list applied to packets on R is: adj-SID 100 - link from R to R1 adj-SID 200 - link from R1 to R2 adj-SID 300 - link from R2 to L1 bud-SID 1000 - L1 bud-SID 2000 - L2 P2MP chain 2: Path: R -> R1 -> R3 -> R5 -> R6 -> L3 -> R8 -> L4, where L3 is a transit leaf node, and L4 is the tail-end leaf node. Assuming that the sub-path R -> R1 -> R3 -> R5 -> R6 -> L3 matches the shortest path from R to L3, the bud-SID of L3 is used to represent this sub-path. The segment list applied to packets on R is: bud-SID 3000 - L3 adj-SID 600 - link from L3 to R8 adj-SID 700 - link from R8 to L4 bud-SID 4000 - L4 5. Path Computation for P2MP Chains Path computation for the P2MP chains of a P2MP transport scheme {root node, leaf nodes} lies in the responsibility of a controller or the root node. This document does not enforce a particular computation algorithm. In fact, any P2P path computation algorithm may be extended to serve the purpose. The path computation may consider general metric for shortest paths, or traffic engineering (TE) constraints for TE paths. This document recommends the following constraints to be considered as well: Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 8] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 - The maximum hop count of path. This SHOULD be based on the maximum delay allowed for a packet to accumulate before reaching a tail-end leaf node. - The maximum length of SID list. This SHOULD be based on the maximum header size which a root node may apply to a packet. This is typically a limit of forwarding hardware. Note that a SID list is translated from a computed path. Hence, the length of the SID list and the hop count of the path are typically not the same. The path computation may achieve more predictable results by dividing leaf nodes into groups based on their geographical or administrative location. Thus, paths MAY be computed in a manner that each P2MP chain is used to reach only a given group, while the number of P2MP chains to reach all the leaf nodes of the group is minimized. 6. IGP and BGP-LS Extensions for Bud Segment The protocol extensions of IGP (ISIS and OSPF) and BGP-LS for bud segment advertisement will be specified in the next version of this document. 7. IANA Considerations This document requires IANA registration and allocation for the ISIS, OSPF and BGP-LS extensions for bud segment advertisement. The details will be provided in the next version of this document. 8. Security Considerations This document introduces bud segments for leaf nodes to act as both packet receivers and transit routers. A security attack may target on a leaf node by constructing malicious packets with the node's bud- SID. Such kind of attacks can be defeated by restricting bud segment distribution and P2MP chain construction within the scope of a controller and a given network. 9. Acknowledgements This document leverages work done by Alexander Arseniev and Ron Bonica. Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 9] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 10. References 10.1. Normative References [RFC8402] Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L., Decraene, B., Litkowski, S., and R. Shakir, "Segment Routing Architecture", RFC 8402, DOI 10.17487/RFC8402, July 2018, . [RFC8660] Bashandy, A., Ed., Filsfils, C., Ed., Previdi, S., Decraene, B., Litkowski, S., and R. Shakir, "Segment Routing with the MPLS Data Plane", RFC 8660, DOI 10.17487/RFC8660, December 2019, . [SRv6-SRH] Filsfils, C., Dukes, D., Previdi, S., Leddy, J., Matsushima, S., and D. Voyer, "IPv6 Segment Routing Header", draft-ietf-6man-segment-routing-header (work in progress), 2019. [SRv6-Programming] Filsfils, C., Garvia, P., Leddy, J., Voyer, D., Matsushima, S., and Z. Li, "SRv6 Network Programming", draft-ietf-spring-srv6-network-programming (work in progress), 2019. 10.2. Informative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . Authors' Addresses Yimin Shen Juniper Networks 10 Technology Park Drive Westford, MA 01886 USA Email: yshen@juniper.net Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 10] Internet-DraftPoint-to-Multipoint Transport Using Chain RepFebruary 2020 Zhaohui Zhang Juniper Networks 10 Technology Park Drive Westford, MA 01886 USA Email: zzhang@juniper.net Yimin Shen & Zhaohui ZhanExpires August 6, 2020 [Page 11]