Network Working Group Eric C. Rosen Internet Draft Peter Psenak Expiration Date: December 2001 Cisco Systems, Inc. Padma Pillay-Esnault Juniper Networks, Inc. June 2001 OSPF as the PE/CE Protocol in BGP/MPLS VPNs draft-rosen-vpns-ospf-bgp-mpls-02.txt Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract [VPN] describes a method of providing a VPN service. That method allows a variety of different protocols to be used as the routing protocol between the Customer Edge (CE) router and the Provider Edge (PE) router. However, it does not fully specify the procedures which must be implemented within the Provider's network when OSPF is used as the PE/CE routing protocol. This document provides that specification. Rosen, et al. [Page 1] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 Table of Contents 1 Specification of Requirements ........................ 2 2 Introduction ......................................... 2 3 Requirements ......................................... 3 4 BGP/OSPF Interaction Procedures for PE routers ....... 5 4.1 Overview ............................................. 5 4.2 Details .............................................. 7 4.2.1 General .............................................. 7 4.2.2 Handling LSAs from the CE ............................ 9 4.2.3 Sham Links ........................................... 11 4.2.3.1 Intra-Area Routes .................................... 11 4.2.3.2 Creating Sham Links .................................. 12 4.2.3.3 Treatment of Sham Links .............................. 13 4.2.4 VPN-IP routes received via BGP ....................... 13 5 ID Summary for Sub-IP Area ........................... 15 5.1 Summary .............................................. 15 5.2 Related Documents .................................... 15 5.3 Targeted at PPVPN WG ................................. 15 6 Acknowledgments ...................................... 15 7 Authors' Address ..................................... 16 8 Bibliography ......................................... 16 1. Specification of Requirements The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119. 2. Introduction [VPN] describes a method by which a Service Provider (SP) can use its IP backbone to provide a VPN service to customers. In that method, a customer's edge devices (CE devices) are connected to the provider's edge routers (PE routers). If the CE device is a router, then the PE router may become a routing peer of the CE router (in some routing protocol), and may as a result learn the routes which lead to the CE's site and which need to be distributed to other PE routers that attach to the same VPN. The PE routers which attach to a common VPN use BGP to distribute the Rosen, et al. [Page 2] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 VPN's routes to each other. A CE router can then learn the routes to other sites in the VPN by peering with its attached PE router in a routing protocol. CE routers at different sites do not, however, peer with each other. It can be expected that many VPNs will use OSPF as their internal routing protocol. This does not necessarily mean that the PE routers need to use OSPF to peer with the CE routers. Each site in a VPN can use OSPF as its intra-site routing protocol, while using, e.g., BGP or RIP to distribute routes to a PE router. However, it is certainly convenient, when OSPF is being used intra-site, to use it on the PE- CE link as well, and [VPN] explicitly allows this. Like anything else, the use of OSPF on the PE-CE link has advantages and disadvantages. The disadvantage to using OSPF on the PE-CE link is that it gets the PE router involved in a VPN site's IGP, however peripherally. The advantages though are: - The administrators of the CE router need not have any expertise in any routing protocol other than OSPF. - The CE routers do not need to have support for any routing protocols other than OSPF. - If a customer is transitioning his network from a traditional OSPF backbone to the VPN service described in [VPN], the use of OSPF on the PE-CE link eases the transitional issues. It seems likely that some SPs and their customers will resolve these trade-offs in favor of the use of OSPF on the PE-CE link. Thus we need to specify the procedures which must be implemented by a PE router in order to make this possible. (No special procedures are needed in the CE router though; CE routers just run whatever OSPF implementations they may have.) 3. Requirements Consider a set of VPN sites which are thought of as a common "OSPF domain". These will almost certainly be a set of sites which together constitute an "intranet", and each of which runs OSPF as its intra-site routing protocol. Per [VPN], the VPN routes are distributed among the PE routers by BGP. If the PE uses OSPF to distribute routes to the CE router, the standard procedures governing BGP/OSPF interactions [OSPF] would cause routes from one site to be delivered to another as AS-external routes (in type 5 LSAs). This is undesirable; it would be much Rosen, et al. [Page 3] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 better to deliver such routes in type 3 LSAs (as inter-area routes), so that they can be distinguished from any "real" AS-external routes that may be circulating in the VPN. (That is, so that they can be distinguished by OSPF from routes which really do not come from within the VPN.) Hence it is necessary for the PE routers to implement a modified version of the BGP/OSPF interaction procedures. In fact, we would like to have a very general set of procedures which allows a customer to easily replace a legacy private OSPF backbone with the VPN service. We would like this procedure to meet the following set of requirements: - The procedures should not make assumptions about the OSPF topology. In particular, it should not be assumed that customer sites are OSPF stub sites or NSSA sites. Nor should it be assumed that a customer site contains only one OSPF area, or that it has no area 0 routers. - If VPN sites A and B are in the same OSPF domain, then routes from one should be presented to the other as OSPF intra-network routes. In general, this can be done by presenting such routes in type 3 LSAs. Note that this allows two VPN sites to be connected via an "OSPF backdoor link". That is, one can have an OSPF link between the two sites which is used only when the VPN backbone is unavailable. (This would not be possible with the ordinary BGP/OSPF interaction procedures. The ordinary procedures would present routes via the VPN backbone as AS-external routes, and these could never be preferred to intra-network routes.) This may be very useful during a period of transition from a legacy OSPF backbone to a VPN backbone. - It should be possible to make use of an "OSPF backdoor link" between two sites, even if the two sites are in the same OSPF area, and neither of the routers attached to the inter-site backdoor link is an area 0 router. This can also be very useful during a transition period, and eliminates any need to reconfigure the sites' routers to be ABRs. Assuming that it is desired to have the route via the VPN backbone be preferred to the backdoor route, the VPN backbone itself must be presented to the CE routers at each site as a link between the two PE routers to which the CE routers are respectively attached. Rosen, et al. [Page 4] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 - CE routers, connected to PE routers of the VPN service, may themselves function as OSPF backbone (area 0) routers. An OSPF backbone may even consist of several "segments" which are interconnected themselves only via the VPN service. In such a scenario, full intercommunication between sites connected to different segments of the OSPF backbone should still be possible. - The transition from the legacy private OSPF backbone to the VPN service must be simple and straightforward. The transition is likely to be phased, such that customer sites are migrated one by one from the legacy private OSPF backbone to the VPN service. During the transition, any given site might be connected to the VPN service, to the legacy OSPF backbone, or to both. Complete connectivity among all such sites must be maintained. Since the VPN service is to replace the legacy backbone, it must be possible, by suitable adjustment of the OSPF metrics, to make OSPF prefer routes which traverse the SP's VPN backbone to alternative routes which do not. - The OSPF metric assigned to a given route should be carried transparently over the VPN backbone. Routes from sites which are not in the same OSPF domain will appear as AS-external routes. We presuppose familiarity with the contents of [OSPF], including the OSPF LSA types, and will refer without further exegesis to type 1, 2, 3, etc., LSAs. Familiarity with [VPN] is also presupposed. 4. BGP/OSPF Interaction Procedures for PE routers 4.1. Overview [VPN] defines the notion of a Per-Site Routing and Forwarding Table, or VRF. A PE router must be capable of running multiple instances of OSPF, where each instance is associated with a particular VRF. (Whether these instances are realized as separate processes, or merely as separate contexts of a common process, is an implementation matter.) BGP is used to distribute routes among the set of PE routers that attach to a single OSPF domain. Per [VPN], these routes are distributed as VPN-IP routes. Import/export to/from particular VRFs is governed via Route Targets. To meet the above requirements, a PE which imports a particular route into a particular VRF needs to know whether that route comes from the same OSPF domain and the same OSPF Rosen, et al. [Page 5] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 area as the CEs to which it is attached. Our procedure is to encode this information as BGP Extended Communities attributes [EXT], and have BGP distribute it along with the VPN-IP route. The OSPF metric of a route is also carried as a BGP attribute of the route. If two PEs attach to different VPN sites that are in the same OSPF area (as indicated by the OSPF area number), the PE/CE links to those site MAY be treated as links within that area. In addition, each PE MAY flood, into that area, a type 1 LSA advertising a link to the other PE. If this procedure is followed, two VPN sites in the same OSPF area will see the VPN backbone as a link within that area, a link between the two PE routers. We refer to this link as a "sham link". This allows routes from one site to the other to be treated as intra-area routes. The procedures governing the use of sham links are specified in Section 4.2.3. Every PE attached to a particular OSPF network MUST be an OSPF area 0 router. This allows it to distribute inter-area routes to the CE via Type 3 LSAs. The CE router might or might not be an area 0 router, and the PE/CE link might or might not be an area 0 link. If the OSPF network contains area 0 routers (other than the PE routers), at least one PE router must have an area 0 link to a non-PE area 0 router in that OSPF network. (The non-PE area 0 router functions as a CE router.) This ensures that inter-area routes and AS-external routes can be leaked between the PE routers and the non- PE OSPF backbone. When a type 3 LSA is sent over an area 0 link from a PE router to a CE router, a special bit in the LSA Options field is set. This is used to ensure that if any CE router sends this type 3 LSA to a PE router, the PE router will not further redistribute it. Two sites which are not in the same OSPF area will see the VPN backbone as being an integral part of the OSPF backbone. However, if there are area 0 routers which are NOT PE routers, then the VPN backbone actually functions as a sort of higher level backbone, providing a third level of hierarchy above area 0. This allows a legacy OSPF backbone to become disconnected during a transition period, as long as the various segments all attach to the VPN backbone. When a PE router needs to distribute to a CE router a route which comes from a site outside the latter's OSPF domain, the PE router presents itself as an ASBR, and distributes the route in a type 5 LSA. OSPF route tagging is used to ensure that a type 5 LSA generated by a PE router will be ignored by any other PE router that may receive it. A special OSPF route tag, which we will call the VPN Rosen, et al. [Page 6] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 Route Tag, will be used for this purpose. 4.2. Details 4.2.1. General If a PE and a CE are communicating via OSPF, the PE MUST create, and MUST flood to the CE, a type 1 LSA advertising its link to the CE. The PE MUST have an OSPF router id which is valid (i.e., unique) within the OSPF domain. The PE MUST also be configured to know which OSPF area the link is in. A PE-CE link may be in any area, including area 0; this is a matter of the OSPF configuration. Whether or not the PE-CE link is an area 0 link, the PE itself MUST be an OSPF area 0 router. That is, the link state topology from a site will not be passed along by the PE. The PE MUST support at least one OSPF instance for each OSPF domain to which it attaches. Each instance of OSPF MUST be associated with a single VRF. If n CEs associated with that VRF are running OSPF on their respective PE/CE links, then those n CEs are OSPF adjacencies of the PE in the corresponding instance of OSPF. Generally, though not necessarily, if the PE attaches to several CEs in the same OSPF domain, it will associate the interfaces to those PEs with a single VRF. If the OSPF domain has any area 0 routers (other than the PE routers), then at least one of those MUST be a CE router, and MUST have an area 0 link to at least one PE router. This adjacency MAY be via an OSPF virtual link. Each OSPF domain MUST be associated with a Domain Identifier. This MUST be configurable, and the default value (if none is configured) MUST be zero. More precisely, each VRF associated with an OSPF instance will either be configured with a Domain Identifier, or else will use zero as its Domain Identifier. All VRFs which correspond to the same OSPF domain MUST be configured with the same value of this attribute, or else all must use the default value of zero. If a non-zero Domain Identifier value is configured, it must be a globally unique value which can be encoded in a BGP Extended Communities attribute. Routes from a particular OSPF domain will, when distributed in BGP as VPN-IPv4 routes, carry this attribute. (However, if the attribute value is zero, then the attribute SHOULD not be carried.) The OSPF Domain will be encoded as the VPN of Origin Extended Community [VPN, EXT] attribute. (It is shown in [VPN] how to assign globally unique values to this attribute.) Rosen, et al. [Page 7] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 If a Domain Identifier is not configured for a particular OSPF domain, then care must be taken to avoid having routes from that OSPF domain and routes from another OSPF domain imported into the same VRF. If a particular VRF in a PE is associated with an instance of OSPF, then it will be configured with a special OSPF route tag value, which we call the VPN Route Tag. This route tag MUST be included in the Type 5 LSAs which the PE originates (as the result of receiving a BGP-distributed VPN-IP route, see section 4.2.4) and sends to any of the attached CEs. Its value is arbitrary, but must be distinct from any OSPF Route Tag being used within the OSPF domain. Its value MUST therefore be configurable. The default value SHOULD be an automatically computed tag based on the Autonomous System number of the VPN backbone: Tag = 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |1|1|0|1| ArbitraryTag | AutonomousSystem | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 _AS number of the VPN Backbone_ If a PE router needs to use OSPF to distribute to a CE router a route which comes from a site outside the CE router's OSPF domain, the PE router SHOULD present itself to the CE router as an Autonomous System Border Router (ASBR), and SHOULD report such routes as AS-external routes. That is, these PE routers originate Type 5 LSAs reporting the extra-domain routes as AS-external routes. Each such Type 5 LSA MUST contain an OSPF route tag whose value is that of the VPN Route Tag. This tag identifies the route as having come from a PE router. The VPN Route Tag MUST be used to ensure that a Type 5 LSA originated by a PE router is not redistributed through the OSPF area to another PE router. When a PE/CE link is an area 0 link, the high-order bit of the LSA Options field (previously unused) is used to distinguish type 3 LSAs which report routes across the VPN backbone from other VPN sites. We refer to this as the DN bit. The DN bit is set in a type 3 LSA which is sent from a PE router to a CE router across an area 0 link. When a PE router receives, from a CE router, a type 3 LSA with the DN bit set, the route is ignored. Without this mechanism, the type 3 LSA Rosen, et al. [Page 8] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 could be sent by a PE to a CE, flooded through a number of OSPF routers, and then sent to another PE; this could cause a loop. This mechanism prevents such loops. 4.2.2. Handling LSAs from the CE This section specifies the way in which a PE router handles the OSPF LSAs it receives from a CE router. If a route is received in a Type 5 LSA, and if it has an OSPF route tag value equal to the VPN Route Tag, then that route is ignored. If a route is received in a Type 3 LSA, and if it has the DN bit set in its Options Field, then the route is ignored. Otherwise, there is normal OSPF processing, for the relevant instance of OSPF in the PE. Next, the PE must examine the corresponding VRF. For every address prefix which appears there, the PE must create a VPN-IPv4 route in BGP. Each such route will have some of the following Extended Community attributes: - The VPN of Origin Extended Community attribute. This MUST be present, UNLESS the VRF has the (default) Domain Identifier value of zero. In this case, the attribute MAY be omitted. - OSPF Route Type Extended Community Attribute. This attribute MUST be present, and is encoded as follows: * Type: 0x8000 * Area Number: 4 bytes, encoding a 32-bit area number. For AS- external routes, the value is 0. A non-zero value identifies the route as being internal to the OSPF domain, and as being within the identified area. Area numbers are relative to a particular OSPF domain. * OSPF Route Type: 1 byte, encoded as follows: ** 1 or 2 for intra-area routes (depending on whether the route came from a type 1 or a type 2 LSA -- however this difference is not significant to the procedures specified herein) Rosen, et al. [Page 9] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 ** 3 for summary routes ** 5 for external routes (area number must be 0) ** 7 for NSSA routes. ** 129 for Sham Link Endpoint Addresses. See section 4.2.3.2 for the specification of when this value must be used. * Options: 1 byte. Currently this is only used if the route type is 5 or 7. Setting the least significant bit in the field indicates that the route carries a type 2 metric. - OSPF Router Id Extended Community. This OPTIONAL attribute specifies the OSPF Router Id of the system that is identified in the BGP Next Hop attribute. More precisely, it specifies the Router Id of the particular VRF from which this route was exported. * Type: 0x8001 * Router Address: 4 Bytes * Unused: 2 Bytes. - MED. By default, this SHOULD be set to the value of the OSPF distance associated with the route, plus 1. The intention of all this is the following. OSPF Routes from one site are converted to BGP, distributed across the VPN backbone, and possibly converted back to OSPF routes before being distributed into another site. With these attributes, BGP carries enough information about the route to enable the route to be converted back into OSPF "transparently", just as if BGP had not been involved. Routes which a PE receives in type 4 LSAs MUST be ignored. The attributes specified above are in addition to any other attributes which routes must carry in accord with the [VPN]. The Site of Origin attribute, which is usually required by [VPN], is OPTIONAL for routes which a PE learns from a CE via OSPF. Use of the Site of Origin attribute would, in the case of a multiply homed site (i.e., a site attached to several PE routers), prevent an intra-site route from being reinjected into a site from the VPN backbone. Such a reinjection would not harm the routing, because the Rosen, et al. [Page 10] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 route via the VPN backbone would be advertised in a type 3 LSA, and hence would appear to be an inter-area route; the real intra-area route would be preferred. But unnecessary overhead would be introduced. On the other hand, if the Site of Origin attribute is not used, a partitioned site will find itself automatically repaired, since traffic from one partition to the other will automatically travel via the VPN backbone. Therefore the use of a Site of Origin attribute is optional, so that a trade-off can be made between the cost of the increased overhead and the value of automatic partition repair. 4.2.3. Sham Links 4.2.3.1. Intra-Area Routes Suppose there are two sites in the same OSPF area. Each site is attached to a different PE router, and there is also an intra-area OSPF link connecting the two sites. It is possible to treat these two sites as a single VPN site which just happens to be multihomed to the backbone. This is in fact the simplest thing to do, and is perfectly adequate, providing that the preferred route between the two sites is via the intra-area OSPF link (a "backdoor link"), rather than via the VPN backbone. There will be routes between sites that go through the PE routers, but these routes will appear to be inter-area routes, and OSPF will consider them to be less preferable than the intra-area routes through the backdoor link. If it is desired to have OSPF prefer the routes through the backbone over the routes through the backdoor link, then the routes through the backbone must be appear to be intra-area routes. To make a route through the backbone appear to be an inter-area route, it is necessary to make it appear as if there is an intra-area link connecting the two PE routers. This is what we refer to as a "sham link". (If the two sites attach to the same PE router, this of course is not necessary.) A sham link can be thought of as a relation between two VRFs. If two VRFs are to be connected by a sham link, each VRF must be associated with a "Sham Link Endpoint Address", a /32 address which is treated as an address of the PE router containing that VRF. The Sham Link Endpoint Address associated with a VRF MUST be configurable, and it MAY default to the VRF's router id. The Sham Link Endpoint Address is an address in the VPN's address space, not the SP's address space. A VRF needs only a single Sham Link Endpoint Address, no matter how Rosen, et al. [Page 11] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 many sham links it has. It MUST be distributed by BGP as a VPN-IPv4 address, and it MAY be distributed by OSPF. 4.2.3.2. Creating Sham Links Sham links may be manually configured, or they may be auto- configured. Each VRF that is associated with a PE-CE link on which OSPF is running MUST be configurable as to whether auto-configuration of sham links to/from that VRF is allowed. The default MUST be "manual configuration". If a VRF is configured for manual configuration of the sham links, it will never initiate auto-configuration of a sham link, nor will it ever create a sham link as the result of a remotely initiated auto- configuration procedure. If a VRF is configured for auto- configuration of sham links, manual configuration of particular sham links is still allowed. In any event, no more than one sham link with the same pair of sham link endpoint addresses will ever be created. To manually configure a sham link between two VRFs, each VRF has to be configured to create a sham link to the other, where the "other" is identified by its sham link endpoint address. Procedures for single-ended manual configuration of the sham link are for further study. IF a VRF is configured for auto-configuration of sham links, it MUST distribute, via BGP, a VPN-IP route corresponding to the Sham Link Endpoint Address. This route MUST have the OSPF Route Type Extended Community attribute, with the OSPF Route Type field set to "Sham Link Endpoint Address". When a PE receives such a route, with a RT value that allows the route to be imported into a particular VRF, then if - that route has an OSPF Domain Id which matches that of the VRF (an OSPF Domain Id with value 0 is considered a match is the VRF has no OSPF Domain Id), AND - that route has an OSPF area number which matches that of the VRF, then a sham link may be created from the local VRF to the VRF identified by the sham link endpoint address. If all VRFs are configured for auto-configuration of sham links, a Rosen, et al. [Page 12] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 full mesh of sham links will be created among all the sites which are in the same OSPF area. This may not be what is desired. To obtain more control over the set of sham links which are created, some or all of the VRFs can be configured to disable auto-configuration of the sham links. Note that sham links may be created for any area, including area 0. 4.2.3.3. Treatment of Sham Links Sham links SHOULD be treated by OSPF as OSPF Demand Circuits. This means that LSAs will be flooded over them, but periodic refresh traffic is avoided. Note that, as long as the backdoor link is up, flooding the LSAs over the sham link serves no purpose. However, if the backdoor link goes down, OSPF does not have mechanisms enabling the routers in one site to rapidly flush the LSAs from the other site. Therefore it is still necessary to maintain synchronization among the LSA databases at the two sites, hence the flooding over the sham link. The sham link is an unnumbered point-to-point intra-area link, and is advertised by means of a type 1 LSA. The OSPF metric associated with a sham link must be configurable (and there must be a configurable default). Whether traffic between the sites flows via a backdoor link or via the VPN backbone (i.e., via the sham link) depends on the settings of the OSPF link metrics. The metrics can be set so that the backdoor link is not used unless connectivity via the VPN backbone fails, for example. If a PE determines that a particular route traverses the sham link, then the PE SHOULD NOT redistribute that route into BGP as a VPN-IPv4 route. 4.2.4. VPN-IP routes received via BGP This section describes how the PE router handles VPN-IP routes received via BGP. If a received BGP VPN-IP route is not installed in the VRF, nothing is reported to the CE. A received route will not be installed into the VRF if some other route is preferable. (Note that a route which is not installed in the VRF may still cause the PE to create an OSPF link to another PE as specified in the previous section.) Rosen, et al. [Page 13] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 Note that according to the usual OSPF route preference rules, intra- area routes, as computed by the OSPF, will be installed in the VRF in preference to any other routes received over BGP. This means that the CE will simply not hear about inter-area or external routes to address prefixes for which there is an intra-area route. In the following, we specify what is reported, in OSPF LSAs, by the PE to the CE, assuming that the PE is not configured to do any further summarization or filtering of the routing information before reporting it to the CE. If ONE of the following conditions holds for a given route that is received via BGP: - the VRF has a non-zero Domain Identifier, but the route does not have a non-zero VPN of Origin attribute, or - the route has a VPN of Origin attribute whose value is not the same as the Domain Identifier associated with the VRF, or then the route MUST be distributed to the CE in a type 5 LSA with a type 2 metric. By default, the MED, if present, is converted to a type 2 metric. If the MED is not present, a default type 2 metric value is used. Otherwise, if the route has an OSPF route type of external route, it MUST be advertised to the CE in a type 5 LSA. The VPN Route Tag (see section 4.2.1) MUST be placed in the LSA. By default, the MED, if present, is converted to a type 1 or type 2 metric, as determined by the external route property of the VPN-IPv4 route. If no MED is present, a default type 2 metric value is used. Otherwise, if the route has an OSPF route type of "summary route", the route should be treated as if it had been received in an OSPF type 3 LSA. This means that the PE will report the route in a type 3 LSA to the CE. (Note that this case is possible even if the VPN-IP route carries an area number identical to that of the CE router. This means that if an area is "partitioned" such that the two pieces are connected only via the VPN backbone, it appears to be two areas, with inter-area routes between them.) If the link from the PE to the CE is an area 0 link, the DN bit MUST be set in this LSA; if the link is not an area 0 link, the DN bit MAY be set. Note that this way of handling AS-external routes makes every PE appear to be an ASBR attached to all the AS-external routes. In a multihomed site, this can result in a number of type 5 LSAs containing the same information. Rosen, et al. [Page 14] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 5. ID Summary for Sub-IP Area 5.1. Summary The base specification for RFC2547 VPNs, i.e., [VPN], allows for several methods by which a VPN customer may distribute VPN routes to and receive VPN routes from a service provider. One such method is by the use of OSPF on the link connecting the customer to the service provider. However, the base specification does not describe the full set of procedures needed in order to use OSPF in this manner. This draft provides the specification of those procedures. 5.2. Related Documents draft-ietf-ppvpn-requirements-00.txt draft-ietf-ppvpn-framework-00.txt draft-rosen-rfc2547bis-03.txt draft-rosen-vpn-mcast-00.txt draft-rosen-ppvpn-ipsec-2547-00.txt 5.3. Targeted at PPVPN WG This work addresses the following work item from the PPVPN WG charter: "The working group is expected to consider at least three specific approaches, including BGP-VPNs (e.g. RFC 2547)." It extends the base specification for RFC2547 VPNs by adding procedures governing a fairly common case. The WG should consider this document as it specifically addresses one of the work items called out in the charter. 6. Acknowledgments Significant contributions to this work have been made by Derek Yeung and Yakov Rekhter. Thanks to Ross Callon and Ajay Singhal for their comments. Rosen, et al. [Page 15] Internet Draft draft-rosen-vpns-ospf-bgp-mpls-02.txt June 2001 7. Authors' Address Eric C. Rosen Cisco Systems, Inc. 250 Apollo Drive Chelmsford, MA, 01824 E-mail: erosen@cisco.com Peter Psenak Parc Pegasus, De Kleetlaan 6A 1831 Diegem Belgium E-mail: ppsenak@cisco.com Padma Pillay-Esnault Juniper Networks 1194 N. Mathilda Avenue Sunnyvale, CA 94089 E-mail: padma@juniper.net 8. Bibliography [EXT] "BGP Extended Communities Attribute", draft-ramachandra-bgp- ext-communities-09.txt, Ramachandra, S. and Tappan, D. June 2001. [OSPF] "OSPF Version 2", RFC 2328, Moy, J., April 1998. [VPN] "BGP/MPLS VPNs", draft-rosen-rfc2547bis-03.txt, Rosen, E., et. al., March 2001. Rosen, et al. [Page 16]