QUIC Working Group M. Piraux, Ed. Internet-Draft O. Bonaventure Intended status: Experimental UCLouvain Expires: May 7, 2020 November 04, 2019 Tunneling Internet protocols inside QUIC draft-piraux-quic-tunnel-00 Abstract This document specifies methods for tunneling Internet protocols such as TCP, UDP, IP and QUIC inside a QUIC connection. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on May 7, 2020. Copyright Notice Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Piraux & Bonaventure Expires May 7, 2020 [Page 1] Internet-Draft QUIC Tunnel November 2019 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Conventions and Definitions . . . . . . . . . . . . . . . . . 3 3. Reference environment . . . . . . . . . . . . . . . . . . . . 4 4. The datagram mode . . . . . . . . . . . . . . . . . . . . . . 4 5. The stream mode . . . . . . . . . . . . . . . . . . . . . . . 5 6. Connection establishment . . . . . . . . . . . . . . . . . . 6 7. Messages format . . . . . . . . . . . . . . . . . . . . . . . 7 7.1. QUIC tunnel stream TLVs . . . . . . . . . . . . . . . . . 7 7.1.1. TCP Connect TLV . . . . . . . . . . . . . . . . . . . 8 7.1.2. TCP Extended Connect TLV . . . . . . . . . . . . . . 9 7.1.3. TCP Connect OK TLV . . . . . . . . . . . . . . . . . 10 7.1.4. Error TLV . . . . . . . . . . . . . . . . . . . . . . 10 7.1.5. End TLV . . . . . . . . . . . . . . . . . . . . . . . 11 8. Example flows . . . . . . . . . . . . . . . . . . . . . . . . 11 9. Security Considerations . . . . . . . . . . . . . . . . . . . 12 9.1. Privacy . . . . . . . . . . . . . . . . . . . . . . . . . 12 9.2. Ingress Filtering . . . . . . . . . . . . . . . . . . . . 12 9.3. Denial of Service . . . . . . . . . . . . . . . . . . . . 13 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 13 10.1. Registration of QUIC tunnel Identification String . . . 13 10.2. QUIC tunnel stream TLVs . . . . . . . . . . . . . . . . 13 10.2.1. QUIC tunnel stream TLVs Types . . . . . . . . . . . 13 10.2.2. QUIC tunnel streams TLVs Error Types . . . . . . . . 14 11. References . . . . . . . . . . . . . . . . . . . . . . . . . 14 11.1. Normative References . . . . . . . . . . . . . . . . . . 14 11.2. Informative References . . . . . . . . . . . . . . . . . 15 Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 17 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 17 1. Introduction Mobile devices such as laptops, smartphones or tablets have different requirements than the traditional fixed devices. These mobile devices often change their network attachment. They are often attached to trusted networks, but sometimes they need to be connected to untrusted networks where their communications can be eavesdropped, filtered or modified. In these situations, the classical approach is to rely on VPN protocols such as DTLS, TLS or IPSec. These VPN protocols provide the encryption and authentication functions to protect those mobile clients from malicious behaviors in untrusted networks. On the other hand, these devices are often multihomed and many expect to be able to perform seamless handovers from one access network to another without breaking the established VPN sessions. In some situations it can also be beneficial to combine two or more access Piraux & Bonaventure Expires May 7, 2020 [Page 2] Internet-Draft QUIC Tunnel November 2019 networks together to increase the available host bandwidth. A protocol such as Multipath TCP supports those handovers and allows aggregating the bandwidth of different access links. It could be combined with single-path VPN protocols to support both seamless handovers and bandwidth aggregation above VPN tunnels. Unfortunately, Multipath TCP is not yet deployed on most Internet servers and thus few applications would benefit from such a use case. The QUIC protocol opens up a new way to find a clean solution to this problem. First, QUIC includes the same encryption and authentication techniques as deployed VPN protocols. Second, QUIC is intended to be widely used to support web-based services, making it unlikely to be filtered in many networks, in contrast with VPN protocols. Third, the multipath extensions proposed for QUIC enable it to efficiently support both seamless handovers and bandwidth aggregation. In this document, we explore how (Multipath) QUIC could be used to enable multi-homed mobile devices to communicate securely in untrusted networks. Section 3 describes the reference environment of this document. Then, we explore and compare two different designs. The first, explained in Section 4, uses the recently proposed datagram extension ([I-D.pauly-quic-datagram]) for QUIC to transport plain IP packets over a Multipath QUIC connection. The second, explained in Section 5, uses the QUIC streams to transport TCP bytestreams over a Multipath QUIC connection. Section 6 specifies how a connection is established in this document proposal. Section 7 specifies the format of the messages introduced by this document. Section 8 contains example flows. Our starting point for this work is Multipath QUIC that was initially proposed in [CoNEXT]. A detailed specification of Multipath QUIC may be found in [I-D.deconinck-quic-multipath]. Two implementations of different versions of this protocol are available [CoNEXT], [SIGCOMM19]. 2. Conventions and Definitions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. Piraux & Bonaventure Expires May 7, 2020 [Page 3] Internet-Draft QUIC Tunnel November 2019 3. Reference environment We consider a multihomed client that is attached to one or several access networks. It establishes a Multipath QUIC connection to a concentrator. This MPQUIC connection is used to carry the UDP and TCP packets sent by the client. Thanks to the security mechanisms used by the Multipath QUIC connection, the client data is protected against attacks in one or both of the access networks. The client trusts the concentrator. The concentrator decrypts the QUIC packets exchanged over the Multipath QUIC connection and interacts with the remote hosts as a VPN concentrator would do. +---------+ .----| Access |----. | | network | | v | A | | +--------+ +---------- v +-------------+ | Multi | +--------------+ | Final | | homed | | Concentrator |<===\ ... \===>| destination | | client | +--------------+ | server | +--------+ +---------+ ^ +-------------+ ^ | Access | | | | network | | Legend: .----| B |----. --- Multipath QUIC subflow +---------+ === TCP/UDP flow Figure 1: Example environment Figure 1 illustrates a client-initiated flow. We also discuss inbound connections in this document in Section 6. 4. The datagram mode Our first mode of operation, called the datagram mode in this document, enables the client and the concentrator to exchange raw IP packets through the Multipath QUIC connection. This is done by using the recently proposed QUIC datagram extension [I-D.pauly-quic-datagram]. In a nutshell, to send an IP packet to a remote host, the client simply passes the entire packet as a datagram to the Multipath QUIC connection established with the concentrator. The IP packet is encoded in a QUIC DATAGRAM frame, then encrypted and authenticated in a QUIC packet. This transmission is subject to congestion control, but the datagram that contains the packet is not retransmitted in case of losses as specified in [I-D.pauly-quic-datagram]. The datagram mode is intended to provide a similar service as the one provided by IPSec tunnels or DTLS. Piraux & Bonaventure Expires May 7, 2020 [Page 4] Internet-Draft QUIC Tunnel November 2019 ,->+----------+ | | IP | QUIC packet | +----------+ containing | | UDP | a DATAGRAM | +----------+ frame | | QUIC | | |..........| | | DATAGRAM | | |+--------+|<-. | || IP || | | |+--------+| | Tunneled | || UDP || | UDP packet | |+--------+| | | | .... |<-. `->+----------+ Figure 2: QUIC packet sent by the client when tunneling a UDP packet Figure 2 illustrates how a UDP packet is tunneled using the datagram mode. The main advantage of the datagram mode is that it supports IP and any protocol above the network layer. Any IP packet can be transported using the datagram extension over a Multipath QUIC connection. However, this advantage comes with a large per-packet overhead since each packet contains both a network and a transport header. All these headers must be transmitted in addition with the IP/UDP/QUIC headers of the Multipath QUIC connection. For TCP connections for instance, the per-packet overhead can be large. 5. The stream mode Since QUIC support multiple streams, another possibility to carry the data exchanged over TCP connections between the client and the concentrator is to transport the bytestream of each TCP connection as one of the bidirectional streams of the Multipath QUIC connection. For this, we base our approach on the 0-RTT Converter protocol [I-D.ietf-tcpm-converters] that was proposed to ease the deployment of TCP extensions. In a nutshell, it is an application proxy that converts TCP connections, allowing the use of new TCP extensions through an intermediate relay. We use a similar approach in our stream mode. When a client opens a stream, it sends at the beginning of the bytestream one or more TLV messages indicating the IP address and port number of the remote destination of the bytestream. Their format is detailed in section Section 7.1. Upon reception of such a TLV message, the concentrator opens a TCP connection towards the specified destination and connects the incoming bytestream of the Multipath QUIC connection to the Piraux & Bonaventure Expires May 7, 2020 [Page 5] Internet-Draft QUIC Tunnel November 2019 bytestream of the new TCP connection (and similarly in the opposite direction). Figure 3 summarizes how the new TCP connection is mapped to the QUIC stream. Actions and events of a TCP connection are translated to action and events of a QUIC stream, so that a state transition of one is translated to the other. +------------------+-------------------------+ | TCP | QUIC Stream | +------------------+-------------------------+ | SYN received | Open Stream, send TLVs | | FIN received | Send Stream FIN | | RST received | Send STOP_SENDING | | | Send RESET_STREAM | | Data received | Send Stream data | +------------------+-------------------------+ +-------------------------------+------------+ | QUIC Stream | TCP | +-------------------------------+------------+ | Stream opened, TLVs received | Send SYN | | Stream FIN received | Send FIN | | STOP_SENDING received | Send RST | | RESET_STREAM received | Send RST | | Stream data received | Send data | +-------------------------------+------------+ Figure 3: TCP connection to QUIC stream mapping The QUIC stream-level flow control can be tuned to match the receive window size of the corresponding TCP, so that no excessive data needs to be buffered. 6. Connection establishment The client MUST establish a connection using the Multipath Extensions defined in [I-D.deconinck-quic-multipath]. During connection establishment, the QUIC tunnel support is indicated by setting the ALPN token "qt" in the TLS handshake. Draft-version implementations MAY specify a particular draft version by suffixing the token, e.g. "qt-00" refers to the first version of this document. The concentrator can control the number of connections bytestreams that can be opened initially by setting the initial_max_streams_bidi QUIC transport parameter as defined in [I-D.ietf-quic-transport]. Piraux & Bonaventure Expires May 7, 2020 [Page 6] Internet-Draft QUIC Tunnel November 2019 After the QUIC connection is established, the client can start using the datagram or the stream mode. The client may use PCP [RFC6887] to request the concentrator to accept inbound connections on their behalf. After the negotiation of such port mappings, the concentrator can start opening bidirectional streams to forward inbound connections as well as sending IP packets containing inbound UDP connections in QUIC datagrams. 7. Messages format In the following sections, we specify the format of each message introduced in this document. They are encoded as TLVs, i.e. (Type, Length, Value) tuples, as illustrated in Figure 4. All TLV fields are encoded in network-byte order. 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (8) | Length (8) | [Value (*)] ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: QUIC tunnel TLV Format The Type field is encoded as a byte and identifies the type of the TLV. The Length field is encoded as a byte and indicate the length of the Value field. A value of zero indicates that no Value field is present. The Value field is a type-specific value whose length is determined by the Length field. 7.1. QUIC tunnel stream TLVs When using the stream mode, a one or more messages are used to trigger and confirm the establishment of a connection towards the final destination for a given stream. Those messages are exchanged on this given QUIC stream before the TCP connection bytestream. This section describes the format of these messages. This document specifies the following QUIC tunnel stream TLVs: Piraux & Bonaventure Expires May 7, 2020 [Page 7] Internet-Draft QUIC Tunnel November 2019 +------+----------+-----------------------------+ | Type | Size | Name | +------+----------+-----------------------------+ | 0x00 | 20 bytes | TCP Connect TLV | | 0x01 | 38 bytes | TCP Extended Connect TLV | | 0x02 | 2 bytes | TCP Connect OK TLV | | 0x03 | Variable | Error TLV | | 0xff | 2 bytes | End TLV | +------+----------+-----------------------------+ Figure 5: QUIC tunnel stream TLVs The TCP Connect TLV is used to establish a TCP connection through the tunnel towards the final destination. The TCP Extended Connect TLV allows indicating more information in the establishment request. The TCP Connect OK TLV confirms the establishment of this TCP connection. The Error TLV is used to indicate any out-of-band error that occurred during the TCP connection establishment associated to the QUIC stream. Finally, the End TLV marks the end of the series of TLVs and the start of the bytestream on a given QUIC stream. These TLVs are detailed in the following sections. Offset 0 Offset 20 Offset 22 | | | v v v +-----------------+---------+---------------- Stream 0 | TCP Connect TLV | End TLV | TCP bytestream ... +-----------------+---------+---------------- Figure 6: Example of use of QUIC tunnel stream TLVs 7.1.1. TCP Connect TLV The TCP Connect TLV indicates the final destination of the TCP connection associated to a given QUIC stream. The fields Remote Peer Port and Remote Peer IP Address contain the destination port number and IP address of the final destination. The Remote Peer IP Address MUST be encoded as an IPv6 address. IPv4 addresses MUST be encoded using the IPv4-Mapped IPv6 Address format defined in [RFC4291]. Further, the Remote Peer IP address field MUST NOT include multicast, broadcast, and host loopback addresses [RFC6890]. A QUIC tunnel peer MUST NOT send more than one TCP Connect TLV per QUIC stream. A QUIC tunnel peer MUST NOT send a TCP Connect TLV if a TCP Extended Connect TLV was previously sent on a given stream. A Piraux & Bonaventure Expires May 7, 2020 [Page 8] Internet-Draft QUIC Tunnel November 2019 QUIC tunnel peer MUST NOT send a TCP Connect TLV on non-self initiated streams. 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (8) | Length (8) | Remote Peer Port (16) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Remote Peer IP Address (128) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7: TCP Connect TLV 7.1.2. TCP Extended Connect TLV The TCP Extended Connect TLV is an extended version of the TCP Connect TLV. It also indicates the source of the TCP connection. The fields Remote Peer Port and Remote Peer IP Address contain the destination port number and IP address of the final destination. The fields Local Peer Port and Local Peer IP Address contain the source port number and IP address of the source of the TCP connection. The Remote (resp. Local) Peer IP Address MUST be encoded as an IPv6 address. IPv4 addresses MUST be encoded using the IPv4-Mapped IPv6 Address format defined in [RFC4291]. Further, the Remote (resp. Local) Peer IP address field MUST NOT include multicast, broadcast, and host loopback addresses [RFC6890]. A QUIC tunnel peer MUST NOT send more than one TCP Extended Connect TLV per QUIC stream. A QUIC tunnel peer MUST NOT send a TCP Extended Connect TLV if a TCP Connect TLV was previously sent on a given stream. A QUIC tunnel peer MUST NOT send a TCP Extended Connect TLV on non-self initiated streams. Piraux & Bonaventure Expires May 7, 2020 [Page 9] Internet-Draft QUIC Tunnel November 2019 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (8) | Length (8) | Remote Peer Port (16) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Remote Peer IP Address (128) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Local Peer Port (16) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Local Peer IP Address (128) | | | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 8: TCP Extended Connect TLV 7.1.3. TCP Connect OK TLV The TCP Connect OK TLV does not contain a value. Its presence confirms the successful establishment of connection to the final destination. A QUIC peer MUST NOT send a TCP Connect OK TLV on self- initiated streams. 7.1.4. Error TLV The Error TLV indicates out-of-band errors that occurred during the establishment of the connection to the final destination. These errors can be ICMP Destination Unreachable messages for instance. In this case the ICMP packet received by the concentrator is copied inside the Error Payload field. 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type (8) | Length (8) | Error Code (16) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | [Error Payload (*)] | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 9: Error TLV The following bytestream-level error codes are defined in this document: Piraux & Bonaventure Expires May 7, 2020 [Page 10] Internet-Draft QUIC Tunnel November 2019 +------+---------------------------+ | Code | Name | +------+---------------------------+ | 0x0 | Protocol Violation | | 0x1 | ICMP Packet Received | | 0x2 | Malformed TLV | | 0x3 | Network Failure | +------+---------------------------+ Figure 10: Bytestream-level Error Codes o Protocol Violation (0x0): A general error code for all non- conforming behaviors encountered. A QUIC tunnel peer SHOULD use a more specific error code when possible. o ICMP Packet Received (0x1): This code indicates that the concentrator received an ICMP packet while trying to create the associated TCP connection. The Error Payload contains the packet. o Malformed TLV (0x2): This code indicates that a received TLV was not successfully parsed or formed. A peer receiving a Connect TLV with an invalid IP address MUST send an Error TLV with this error code. o Network Failure (0x3): This codes indicates that a network failure prevented the establishment of the connection. After sending one or more Error TLVs, the sender MUST send an End TLV and terminate the stream, i.e. set the FIN bit after the End TLV. 7.1.5. End TLV The End TLV does not contain a value. Its existence signals the end of the series of TLVs. The next byte in the QUIC stream after this TLV is the start of the tunneled bytestream. 8. Example flows This section illustrates the different messages described previously and how they are used in a QUIC tunnel connection. For QUIC STREAM frames, we use the following syntax: STREAM[ID, Stream Data [, FIN]]. The first element is the Stream ID, the second is the Stream Data contained in the frame and the last one is optional and indicates that the FIN bit is set. Piraux & Bonaventure Expires May 7, 2020 [Page 11] Internet-Draft QUIC Tunnel November 2019 Client Concentrator Final Destination | STREAM[0, "TCP Connect, End"] || | |------------------------------>|| SYN | | ||==============================>| | || SYN+ACK | |STREAM[0,"TCP Connect OK, End"]||<==============================| |<------------------------------|| | | STREAM[0, "bytestream data"] || | |------------------------------>|| bytestream data, ACK | | ||==============================>| | || bytestream data, ACK | | STREAM[0, "bytestream data"] ||<==============================| |<------------------------------|| FIN | | STREAM[0, "", FIN] ||<==============================| |<------------------------------|| ACK | | STREAM[0, "", FIN] ||==============================>| |------------------------------>|| FIN | | ||==============================>| | || ACK | | ||<==============================| Legend: --- Multipath QUIC connection === TCP connection Figure 11: Example flow for the stream mode On Figure 11, the Client is initiating a TCP connection in stream mode to the Final Destination. A request and a response are exchanged, then the connection is torn down gracefully. A remote- initiated connection accepted by the concentrator on behalf of the client would have the order and the direction of all messages reversed. 9. Security Considerations 9.1. Privacy The Concentrator has access to all the packets it processes. It MUST be protected as a core IP router, e.g. as specified in [RFC1812]. 9.2. Ingress Filtering Ingress filtering policies MUST be enforced at the network boundaries, i.e. as specified in [RFC2827]. Piraux & Bonaventure Expires May 7, 2020 [Page 12] Internet-Draft QUIC Tunnel November 2019 9.3. Denial of Service There is a risk of an amplification attack when the Concentrator sends a TCP SYN in response of a TCP Connect TLV. When a TCP SYN is larger than the client request, the Concentrator amplifies the client traffic. To mitigate such attacks, the Concentrator SHOULD rate limit the number of pending TCP Connect from a given client. 10. IANA Considerations 10.1. Registration of QUIC tunnel Identification String This document creates a new registration for the identification of the QUIC tunnel protocol in the "Application Layer Protocol Negotiation (ALPN) Protocol IDs" registry established in [RFC7301]. The "qt" string identifies the QUIC tunnel protocol. Protocol: QUIC tunnel Identification Sequence: 0x71 0x74 ("qt") Specification: This document 10.2. QUIC tunnel stream TLVs IANA is requested to create a new "QUIC tunnel stream Parameters" registry. The following subsections detail new registries within "QUIC tunnel stream Parameters" registry. 10.2.1. QUIC tunnel stream TLVs Types IANA is request to create the "QUIC tunnel stream TLVs Types" sub- registry. New values are assigned via IETF Review (Section 4.8 of [RFC8126]). The initial values to be assigned at the creation of the registry are as follows: Piraux & Bonaventure Expires May 7, 2020 [Page 13] Internet-Draft QUIC Tunnel November 2019 +------+-----------------------------+------------+ | Code | Name | Reference | +------+-----------------------------+------------+ | 0 | TCP Connect TLV | [This-Doc] | | 1 | TCP Extended Connect TLV | [This-Doc] | | 2 | TCP Connect OK TLV | [This-Doc] | | 3 | Error TLV | [This-Doc] | | 255 | End TLV | [This-Doc] | +------+-----------------------------+------------+ 10.2.2. QUIC tunnel streams TLVs Error Types IANA is request to create the "QUIC tunnel stream TLVs Error Types" sub-registry. New values are assigned via IETF Review (Section 4.8 of [RFC8126]). The initial values to be assigned at the creation of the registry are as follows: +------+---------------------------+------------+ | Code | Name | Reference | +------+---------------------------+------------+ | 0 | Protocol Violation | [This-Doc] | | 1 | ICMP packet received | [This-Doc] | | 2 | Malformed TLV | [This-Doc] | | 3 | Network Failure | [This-Doc] | +------+---------------------------+------------+ 11. References 11.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, DOI 10.17487/RFC4291, February 2006, . [RFC6890] Cotton, M., Vegoda, L., Bonica, R., Ed., and B. Haberman, "Special-Purpose IP Address Registries", BCP 153, RFC 6890, DOI 10.17487/RFC6890, April 2013, . Piraux & Bonaventure Expires May 7, 2020 [Page 14] Internet-Draft QUIC Tunnel November 2019 [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . 11.2. Informative References [CoNEXT] De Coninck, Q. and O. Bonaventure, "Multipath QUIC: Design and Evaluation", Proceedings of the 13th International Conference on emerging Networking EXperiments and Technologies (CoNEXT 2017) , December 2017. [I-D.deconinck-quic-multipath] Coninck, Q. and O. Bonaventure, "Multipath Extensions for QUIC (MP-QUIC)", draft-deconinck-quic-multipath-03 (work in progress), August 2019. [I-D.ietf-lpwan-ipv6-static-context-hc] Minaburo, A., Toutain, L., Gomez, C., Barthel, D., and J. Zuniga, "Static Context Header Compression (SCHC) and fragmentation for LPWAN, application to UDP/IPv6", draft- ietf-lpwan-ipv6-static-context-hc-22 (work in progress), October 2019. [I-D.ietf-quic-transport] Iyengar, J. and M. Thomson, "QUIC: A UDP-Based Multiplexed and Secure Transport", draft-ietf-quic-transport-23 (work in progress), September 2019. [I-D.ietf-tcpm-converters] Bonaventure, O., Boucadair, M., Gundavelli, S., Seo, S., and B. Hesmans, "0-RTT TCP Convert Protocol", draft-ietf- tcpm-converters-13 (work in progress), October 2019. [I-D.pauly-quic-datagram] Pauly, T., Kinnear, E., and D. Schinazi, "An Unreliable Datagram Extension to QUIC", draft-pauly-quic-datagram-04 (work in progress), October 2019. [RFC1812] Baker, F., Ed., "Requirements for IP Version 4 Routers", RFC 1812, DOI 10.17487/RFC1812, June 1995, . [RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering: Defeating Denial of Service Attacks which employ IP Source Address Spoofing", BCP 38, RFC 2827, DOI 10.17487/RFC2827, May 2000, . Piraux & Bonaventure Expires May 7, 2020 [Page 15] Internet-Draft QUIC Tunnel November 2019 [RFC3095] Bormann, C., Burmeister, C., Degermark, M., Fukushima, H., Hannu, H., Jonsson, L-E., Hakenberg, R., Koren, T., Le, K., Liu, Z., Martensson, A., Miyazaki, A., Svanbro, K., Wiebke, T., Yoshimura, T., and H. Zheng, "RObust Header Compression (ROHC): Framework and four profiles: RTP, UDP, ESP, and uncompressed", RFC 3095, DOI 10.17487/RFC3095, July 2001, . [RFC3843] Jonsson, L-E. and G. Pelletier, "RObust Header Compression (ROHC): A Compression Profile for IP", RFC 3843, DOI 10.17487/RFC3843, June 2004, . [RFC4019] Pelletier, G., "RObust Header Compression (ROHC): Profiles for User Datagram Protocol (UDP) Lite", RFC 4019, DOI 10.17487/RFC4019, April 2005, . [RFC4815] Jonsson, L-E., Sandlund, K., Pelletier, G., and P. Kremer, "RObust Header Compression (ROHC): Corrections and Clarifications to RFC 3095", RFC 4815, DOI 10.17487/RFC4815, February 2007, . [RFC6846] Pelletier, G., Sandlund, K., Jonsson, L-E., and M. West, "RObust Header Compression (ROHC): A Profile for TCP/IP (ROHC-TCP)", RFC 6846, DOI 10.17487/RFC6846, January 2013, . [RFC6887] Wing, D., Ed., Cheshire, S., Boucadair, M., Penno, R., and P. Selkirk, "Port Control Protocol (PCP)", RFC 6887, DOI 10.17487/RFC6887, April 2013, . [RFC7301] Friedl, S., Popov, A., Langley, A., and E. Stephan, "Transport Layer Security (TLS) Application-Layer Protocol Negotiation Extension", RFC 7301, DOI 10.17487/RFC7301, July 2014, . [RFC8126] Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, June 2017, . Piraux & Bonaventure Expires May 7, 2020 [Page 16] Internet-Draft QUIC Tunnel November 2019 [SIGCOMM19] De Coninck, Q., Michel, F., Piraux, M., Given-Wilson, T., Legay, A., Pereira, O., and O. Bonaventure, "Pluginizing QUIC", Proceedings of the ACM Special Interest Group on Data Communication , August 2019. Acknowledgments Thanks to Quentin De Coninck and Francois Michel for their comments and the proofreading of the first version of this document. Thanks to Gregory Vander Schueren for his comments on the first version of this document. Authors' Addresses Maxime Piraux (editor) UCLouvain Email: maxime.piraux@uclouvain.be Olivier Bonaventure UCLouvain Email: olivier.bonaventure@uclouvain.be Piraux & Bonaventure Expires May 7, 2020 [Page 17]