Network Working Group S. Perreault Internet-Draft Jive Communications Obsoletes: 4008 (if approved) T. Tsou Intended status: Standards Track Huawei Technologies Expires: December 17, 2015 S. Sivakumar Cisco Systems T. Taylor PT Taylor Consulting June 15, 2015 Deprecation of MIB Module NAT-MIB (Managed Objects for Network Address Translators (NAT)) draft-perrault-behave-deprecate-nat-mib-v1-03 Abstract This memo deprecates MIB module NAT-MIB, a portion of the Management Information Base (MIB) previously defined in RFC 4008 for devices implementing Network Address Translator (NAT) function. A companion document defines a new version, NAT-MIB-V2, which responds to deficiencies found in module NAT-MIB and adds new capabilities. This document obsoletes RFC 4008. All RFC 4008 MIB objects are included in this version unchanged with only the STATUS changed to deprecated, with a non-substantive exception. The exception was to retype internet addresses with a (SIZE (4|16) qualification to get rid of a SMILINT warning. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on December 17, 2015. Perreault, et al. Expires December 17, 2015 [Page 1] Internet-Draft Deprecation of NAT MIB v1 June 2015 Copyright Notice Copyright (c) 2015 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. The Internet-Standard Management Framework . . . . . . . . . 3 3. Motivation For Deprecating NAT-MIB . . . . . . . . . . . . . 3 3.1. Deprecated Features . . . . . . . . . . . . . . . . . . . 3 3.2. Desirable New Features . . . . . . . . . . . . . . . . . 4 4. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 4 5. Security Considerations . . . . . . . . . . . . . . . . . . . 54 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 54 7. References . . . . . . . . . . . . . . . . . . . . . . . . . 55 7.1. Normative References . . . . . . . . . . . . . . . . . . 55 7.2. Informative References . . . . . . . . . . . . . . . . . 56 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 56 1. Introduction This memo deprecates a portion of the Management Information Base (MIB), MIB module NAT-MIB, for devices implementing the Network Address Translator (NAT) function. New implementations are encouraged to base themselves upon the second version of this MIB module, NAT-MIB-V2, defined in [I-D.ietf-behave-nat-mib-v2]. NAT types and their characteristics are defined in [RFC2663]. Traditional NAT function, in particular is defined in [RFC3022]. Neither NAT-MIB nor NAT-MIB-V2 addresses firewall functions and neither can be used for configuring or monitoring them. Section 2 provides references to the Simple Network Management Protocol (SNMP) management framework, which was used as the basis for the original MIB module definition and its deprecation. Section 3 provides motivation for the deprecation of module NAT-MIB and its replacement by module NAT-MIB-V2. Section 4 has the complete NAT-MIB module definition, with the STATUS of all objects changed to Perreault, et al. Expires December 17, 2015 [Page 2] Internet-Draft Deprecation of NAT MIB v1 June 2015 deprecated. Section 5 describes security considerations relating to NAT-MIB, basically relying on the security considerations in [RFC4008] and [I-D.ietf-behave-nat-mib-v2]. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to Section 7 of [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, [RFC2578], STD 58, [RFC2579] and STD 58, [RFC2580]. 3. Motivation For Deprecating NAT-MIB This section provides the motivation for deprecating the NAT-MIB module and its replacement by a new version. 3.1. Deprecated Features All objects defined in [RFC4008] have been marked with "STATUS deprecated" for the following reasons: Writability: Experience with NAT has shown that implementations vary tremendously. The NAT algorithms and data structures have little in common across devices, and this results in wildly incompatible configuration parameters. Therefore, few implementations were ever able to claim full compliance. Lesson learned: the MIB should be read-only as much as possible. Exposing configuration parameters: Even in read-only mode, many configuration parameters were exposed by [RFC4008] (e.g. timeouts). Since implementations vary wildly in their sets of configuration parameters, few implementations could claim even basic compliance. Perreault, et al. Expires December 17, 2015 [Page 3] Internet-Draft Deprecation of NAT MIB v1 June 2015 Lesson learned: the NAT MIB's purpose is not to expose configuration parameters. Interfaces: Objects from [RFC4008] tie NAT state with interfaces (e.g. the interface table, the way map entries are grouped by interface). Many NAT implementations either never keep track of the interface or associate a mapping to a set of interfaces. Since interfaces are at the core of [RFC4008], many NAT devices were unable to have a proper implementation. Lesson learned: NAT is a logical function that may be independent of interfaces. Do not tie NAT state with interfaces. NAT service types: [RFC4008] used four categories of NAT service: basicNat, napt, bidirectionalNat, twiceNat. These are ill-defined and many implementations either use different categories or do not use categories at all. Lesson learned: do not try to categorize NAT types. Limited transport protocol set: The set of transport protocols was defined as: other, icmp, udp, tcp. Furthermore, the numeric values corresponding to those labels were arbitrary, without relation to the actual standard protocol numbers. This meant that NAT implementations were limited to those protocols and were unable to expose information about DCCP, SCTP, etc. Lesson learned: use standard transport protocol numbers. 3.2. Desirable New Features A number of desirable new features have been identified that are not present in NAT-MIB. See the latter part of [I-D.ietf-behave-nat-mib-v2] Section 2. 4. Definitions This MIB module IMPORTs objects from [RFC2578], [RFC2579], and [RFC4001]. NAT-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, Gauge32, Perreault, et al. Expires December 17, 2015 [Page 4] Internet-Draft Deprecation of NAT MIB v1 June 2015 Counter64, TimeTicks, mib-2, NOTIFICATION-TYPE FROM SNMPv2-SMI TEXTUAL-CONVENTION, StorageType, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP FROM SNMPv2-CONF ifIndex, ifCounterDiscontinuityGroup FROM IF-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddressType, InetAddress, InetPortNumber FROM INET-ADDRESS-MIB; natMIB MODULE-IDENTITY LAST-UPDATED "201506070000Z" -- RFC Ed.: set to publication date ORGANIZATION "IETF Behavior Engineering for Hindrance Avoidance (BEHAVE) Working Group" CONTACT-INFO "Working Group Email: behave@ietf.org Simon Perreault Jive Communications Quebec, QC Canada Email: sperreault@jive.com Tina Tsou Huawei Technologies Bantian, Longgang District Shenzhen 518129 PR China Email: tina.tsou.zouting@huawei.com Perreault, et al. Expires December 17, 2015 [Page 5] Internet-Draft Deprecation of NAT MIB v1 June 2015 Senthil Sivakumar Cisco Systems 7100-8 Kit Creek Road Research Triangle Park, North Carolina 27709 USA Phone: +1 919 392 5158 Email: ssenthil@cisco.com Tom Taylor PT Taylor Consulting Ottawa Canada Email: tom.taylor.stds@gmail.com" DESCRIPTION "This MIB module defines the generic managed objects for NAT. Copyright (C) The Internet Society (2014). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices." -- RFC Ed.: replace yyyy with actual RFC number & remove this note" REVISION "201506070000Z" -- RFC Ed.: set to publication date DESCRIPTION "Deprecation, published as RFC yyyy." -- RFC Ed.: replace yyyy with actual RFC number & set date" REVISION "200503210000Z" -- 21 March 2005 DESCRIPTION "Initial version, published as RFC 4008." ::= { mib-2 123 } natMIBObjects OBJECT IDENTIFIER ::= { natMIB 1 } NatProtocolType ::= TEXTUAL-CONVENTION STATUS deprecated DESCRIPTION "A list of protocols that support the network address translation. Inclusion of the values is not intended to imply that those protocols need to be supported. Any change in this TEXTUAL-CONVENTION should also be reflected in the definition of NatProtocolMap, which is a BITS representation of this." SYNTAX INTEGER { none (1), -- not specified other (2), -- none of the following Perreault, et al. Expires December 17, 2015 [Page 6] Internet-Draft Deprecation of NAT MIB v1 June 2015 icmp (3), udp (4), tcp (5) } NatProtocolMap ::= TEXTUAL-CONVENTION STATUS deprecated DESCRIPTION "A bitmap of protocol identifiers that support the network address translation. Any change in this TEXTUAL-CONVENTION should also be reflected in the definition of NatProtocolType." SYNTAX BITS { other (0), icmp (1), udp (2), tcp (3) } NatAddrMapId ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "A unique id that is assigned to each address map by a NAT enabled device." SYNTAX Unsigned32 (1..4294967295) NatBindIdOrZero ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "A unique id that is assigned to each bind by a NAT enabled device. The bind id will be zero in the case of a Symmetric NAT." SYNTAX Unsigned32 (0..4294967295) NatBindId ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION "A unique id that is assigned to each bind by a NAT enabled device." SYNTAX Unsigned32 (1..4294967295) NatSessionId ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS deprecated DESCRIPTION Perreault, et al. Expires December 17, 2015 [Page 7] Internet-Draft Deprecation of NAT MIB v1 June 2015 "A unique id that is assigned to each session by a NAT enabled device." SYNTAX Unsigned32 (1..4294967295) NatBindMode ::= TEXTUAL-CONVENTION STATUS deprecated DESCRIPTION "An indication of whether the bind is an address bind or an address port bind." SYNTAX INTEGER { addressBind (1), addressPortBind (2) } NatAssociationType ::= TEXTUAL-CONVENTION STATUS deprecated DESCRIPTION "An indication of whether the association is static or dynamic." SYNTAX INTEGER { static (1), dynamic (2) } NatTranslationEntity ::= TEXTUAL-CONVENTION STATUS deprecated DESCRIPTION "An indication of a) the direction of a session for which an address map entry, address bind or port bind is applicable, and b) the entity (source or destination) within the session that is subject to translation." SYNTAX BITS { inboundSrcEndPoint (0), outboundDstEndPoint(1), inboundDstEndPoint (2), outboundSrcEndPoint(3) } -- -- Default Values for the Bind and NAT Protocol Timers -- natDefTimeouts OBJECT IDENTIFIER ::= { natMIBObjects 1 } natNotifCtrl OBJECT IDENTIFIER ::= { natMIBObjects 2 } Perreault, et al. Expires December 17, 2015 [Page 8] Internet-Draft Deprecation of NAT MIB v1 June 2015 -- -- Address Bind and Port Bind related NAT configuration -- natBindDefIdleTimeout OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The default Bind (Address Bind or Port Bind) idle timeout parameter. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system." DEFVAL { 0 } ::= { natDefTimeouts 1 } -- -- UDP related NAT configuration -- natUdpDefIdleTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The default UDP idle timeout parameter. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system." DEFVAL { 300 } ::= { natDefTimeouts 2 } -- -- ICMP related NAT configuration -- natIcmpDefIdleTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated Perreault, et al. Expires December 17, 2015 [Page 9] Internet-Draft Deprecation of NAT MIB v1 June 2015 DESCRIPTION "The default ICMP idle timeout parameter. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system." DEFVAL { 300 } ::= { natDefTimeouts 3 } -- -- Other protocol parameters -- natOtherDefIdleTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The default idle timeout parameter for protocols represented by the value other (2) in NatProtocolType. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system." DEFVAL { 60 } ::= { natDefTimeouts 4 } -- -- TCP related NAT Timers -- natTcpDefIdleTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The default time interval that a NAT session for an established TCP connection is allowed to remain valid without any activity on the TCP connection. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management Perreault, et al. Expires December 17, 2015 [Page 10] Internet-Draft Deprecation of NAT MIB v1 June 2015 system." DEFVAL { 86400 } ::= { natDefTimeouts 5 } natTcpDefNegTimeout OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The default time interval that a NAT session for a TCP connection that is not in the established state is allowed to remain valid without any activity on the TCP connection. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system." DEFVAL { 60 } ::= { natDefTimeouts 6 } natNotifThrottlingInterval OBJECT-TYPE SYNTAX Integer32 (0 | 5..3600) UNITS "seconds" MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object controls the generation of the natPacketDiscard notification. If this object has a value of zero, then no natPacketDiscard notifications will be transmitted by the agent. If this object has a non-zero value, then the agent must not generate more than one natPacketDiscard 'notification-event' in the indicated period, where a 'notification-event' is the generation of a single notification PDU type to a list of notification destinations. If additional NAT packets are discarded within the throttling period, then notification-events for these changes must be suppressed by the agent until the current throttling period expires. If natNotifThrottlingInterval notification generation is enabled, the suggested default throttling period is 60 seconds, but generation of the natPacketDiscard Perreault, et al. Expires December 17, 2015 [Page 11] Internet-Draft Deprecation of NAT MIB v1 June 2015 notification should be disabled by default. If the agent is capable of storing non-volatile configuration, then the value of this object must be restored after a re-initialization of the management system. The actual transmission of notifications is controlled via the MIB modules in RFC 3413." DEFVAL { 0 } ::= { natNotifCtrl 1 } -- -- The NAT Interface Table -- natInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF NatInterfaceEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table specifies the attributes for interfaces on a device supporting NAT function." ::= { natMIBObjects 3 } natInterfaceEntry OBJECT-TYPE SYNTAX NatInterfaceEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry in the natInterfaceTable holds a set of parameters for an interface, instantiated by ifIndex. Therefore, the interface index must have been assigned, according to the applicable procedures, before it can be meaningfully used. Generally, this means that the interface must exist. When natStorageType is of type nonVolatile, however, this may reflect the configuration for an interface whose ifIndex has been assigned but for which the supporting implementation is not currently present." INDEX { ifIndex } ::= { natInterfaceTable 1 } NatInterfaceEntry ::= SEQUENCE { natInterfaceRealm INTEGER, natInterfaceServiceType BITS, Perreault, et al. Expires December 17, 2015 [Page 12] Internet-Draft Deprecation of NAT MIB v1 June 2015 natInterfaceInTranslates Counter64, natInterfaceOutTranslates Counter64, natInterfaceDiscards Counter64, natInterfaceStorageType StorageType, natInterfaceRowStatus RowStatus } natInterfaceRealm OBJECT-TYPE SYNTAX INTEGER { private (1), public (2) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object identifies whether this interface is connected to the private or the public realm." DEFVAL { public } ::= { natInterfaceEntry 1 } natInterfaceServiceType OBJECT-TYPE SYNTAX BITS { basicNat (0), napt (1), bidirectionalNat (2), twiceNat (3) } MAX-ACCESS read-create STATUS deprecated DESCRIPTION "An indication of the direction in which new sessions are permitted and the extent of translation done within the IP and transport headers." ::= { natInterfaceEntry 2 } natInterfaceInTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of packets received on this interface that were translated. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natInterfaceEntry 3 } Perreault, et al. Expires December 17, 2015 [Page 13] Internet-Draft Deprecation of NAT MIB v1 June 2015 natInterfaceOutTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of translated packets that were sent out this interface. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natInterfaceEntry 4 } natInterfaceDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of packets that had to be rejected/dropped due to a lack of resources for this interface. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natInterfaceEntry 5 } natInterfaceStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." REFERENCE "Textual Conventions for SMIv2, Section 2." DEFVAL { nonVolatile } ::= { natInterfaceEntry 6 } natInterfaceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The status of this conceptual row. Perreault, et al. Expires December 17, 2015 [Page 14] Internet-Draft Deprecation of NAT MIB v1 June 2015 Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the natInterfaceRowStatus column is 'notReady'. In particular, a newly created row cannot be made active until the corresponding instance of natInterfaceServiceType has been set. None of the objects in this row may be modified while the value of this object is active(1)." REFERENCE "Textual Conventions for SMIv2, Section 2." ::= { natInterfaceEntry 7 } -- -- The Address Map Table -- natAddrMapTable OBJECT-TYPE SYNTAX SEQUENCE OF NatAddrMapEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table lists address map parameters for NAT." ::= { natMIBObjects 4 } natAddrMapEntry OBJECT-TYPE SYNTAX NatAddrMapEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This entry represents an address map to be used for NAT and contributes to the dynamic and/or static address mapping tables of the NAT device." INDEX { ifIndex, natAddrMapIndex } ::= { natAddrMapTable 1 } NatAddrMapEntry ::= SEQUENCE { natAddrMapIndex NatAddrMapId, natAddrMapName SnmpAdminString, natAddrMapEntryType NatAssociationType, natAddrMapTranslationEntity NatTranslationEntity, natAddrMapLocalAddrType InetAddressType, natAddrMapLocalAddrFrom InetAddress, natAddrMapLocalAddrTo InetAddress, natAddrMapLocalPortFrom InetPortNumber, Perreault, et al. Expires December 17, 2015 [Page 15] Internet-Draft Deprecation of NAT MIB v1 June 2015 natAddrMapLocalPortTo InetPortNumber, natAddrMapGlobalAddrType InetAddressType, natAddrMapGlobalAddrFrom InetAddress, natAddrMapGlobalAddrTo InetAddress, natAddrMapGlobalPortFrom InetPortNumber, natAddrMapGlobalPortTo InetPortNumber, natAddrMapProtocol NatProtocolMap, natAddrMapInTranslates Counter64, natAddrMapOutTranslates Counter64, natAddrMapDiscards Counter64, natAddrMapAddrUsed Gauge32, natAddrMapStorageType StorageType, natAddrMapRowStatus RowStatus } natAddrMapIndex OBJECT-TYPE SYNTAX NatAddrMapId MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Along with ifIndex, this object uniquely identifies an entry in the natAddrMapTable. Address map entries are applied in the order specified by natAddrMapIndex." ::= { natAddrMapEntry 1 } natAddrMapName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(1..32)) MAX-ACCESS read-create STATUS deprecated DESCRIPTION "Name identifying all map entries in the table associated with the same interface. All map entries with the same ifIndex MUST have the same map name." ::= { natAddrMapEntry 2 } natAddrMapEntryType OBJECT-TYPE SYNTAX NatAssociationType MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This parameter can be used to set up static or dynamic address maps." ::= { natAddrMapEntry 3 } natAddrMapTranslationEntity OBJECT-TYPE SYNTAX NatTranslationEntity MAX-ACCESS read-create Perreault, et al. Expires December 17, 2015 [Page 16] Internet-Draft Deprecation of NAT MIB v1 June 2015 STATUS deprecated DESCRIPTION "The end-point entity (source or destination) in inbound or outbound sessions (i.e., first packets) that may be translated by an address map entry. Session direction (inbound or outbound) is derived from the direction of the first packet of a session traversing a NAT interface. NAT address (and Transport-ID) maps may be defined to effect inbound or outbound sessions. Traditionally, address maps for Basic NAT and NAPT are configured on a public interface for outbound sessions, effecting translation of source end-point. The value of this object must be set to outboundSrcEndPoint for those interfaces. Alternately, if address maps for Basic NAT and NAPT were to be configured on a private interface, the desired value for this object for the map entries would be inboundSrcEndPoint (i.e., effecting translation of source end-point for inbound sessions). If TwiceNAT were to be configured on a private interface, the desired value for this object for the map entries would be a bitmask of inboundSrcEndPoint and inboundDstEndPoint." ::= { natAddrMapEntry 4 } natAddrMapLocalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object specifies the address type used for natAddrMapLocalAddrFrom and natAddrMapLocalAddrTo." ::= { natAddrMapEntry 5 } natAddrMapLocalAddrFrom OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object specifies the first IP address of the range of IP addresses mapped by this translation entry. The value of this object must be less than or equal to the value of the natAddrMapLocalAddrTo object. Perreault, et al. Expires December 17, 2015 [Page 17] Internet-Draft Deprecation of NAT MIB v1 June 2015 The type of this address is determined by the value of the natAddrMapLocalAddrType object." ::= { natAddrMapEntry 6 } natAddrMapLocalAddrTo OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object specifies the last IP address of the range of IP addresses mapped by this translation entry. If only a single address is being mapped, the value of this object is equal to the value of natAddrMapLocalAddrFrom. For a static NAT, the number of addresses in the range defined by natAddrMapLocalAddrFrom and natAddrMapLocalAddrTo must be equal to the number of addresses in the range defined by natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo. The value of this object must be greater than or equal to the value of the natAddrMapLocalAddrFrom object. The type of this address is determined by the value of the natAddrMapLocalAddrType object." ::= { natAddrMapEntry 7 } natAddrMapLocalPortFrom OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS deprecated DESCRIPTION "If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the first port number in the range of ports being mapped. The value of this object must be less than or equal to the value of the natAddrMapLocalPortTo object. If the translation specifies a single port, then the value of this object is equal to the value of natAddrMapLocalPortTo." DEFVAL { 0 } ::= { natAddrMapEntry 8 } natAddrMapLocalPortTo OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS deprecated Perreault, et al. Expires December 17, 2015 [Page 18] Internet-Draft Deprecation of NAT MIB v1 June 2015 DESCRIPTION "If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the last port number in the range of ports being mapped. The value of this object must be greater than or equal to the value of the natAddrMapLocalPortFrom object. If the translation specifies a single port, then the value of this object is equal to the value of natAddrMapLocalPortFrom." DEFVAL { 0 } ::= { natAddrMapEntry 9 } natAddrMapGlobalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object specifies the address type used for natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo." ::= { natAddrMapEntry 10 } natAddrMapGlobalAddrFrom OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object specifies the first IP address of the range of IP addresses being mapped to. The value of this object must be less than or equal to the value of the natAddrMapGlobalAddrTo object. The type of this address is determined by the value of the natAddrMapGlobalAddrType object." ::= { natAddrMapEntry 11 } natAddrMapGlobalAddrTo OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object specifies the last IP address of the range of IP addresses being mapped to. If only a single address is being mapped to, the value of this object is equal to the value of natAddrMapGlobalAddrFrom. For a static NAT, the number of addresses in the range defined Perreault, et al. Expires December 17, 2015 [Page 19] Internet-Draft Deprecation of NAT MIB v1 June 2015 by natAddrMapGlobalAddrFrom and natAddrMapGlobalAddrTo must be equal to the number of addresses in the range defined by natAddrMapLocalAddrFrom and natAddrMapLocalAddrTo. The value of this object must be greater than or equal to the value of the natAddrMapGlobalAddrFrom object. The type of this address is determined by the value of the natAddrMapGlobalAddrType object." ::= { natAddrMapEntry 12 } natAddrMapGlobalPortFrom OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS deprecated DESCRIPTION "If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the first port number in the range of ports being mapped to. The value of this object must be less than or equal to the value of the natAddrMapGlobalPortTo object. If the translation specifies a single port, then the value of this object is equal to the value natAddrMapGlobalPortTo." DEFVAL { 0 } ::= { natAddrMapEntry 13 } natAddrMapGlobalPortTo OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS deprecated DESCRIPTION "If this conceptual row describes a Basic NAT address mapping, then the value of this object must be zero. If this conceptual row describes NAPT, then the value of this object specifies the last port number in the range of ports being mapped to. The value of this object must be greater than or equal to the value of the natAddrMapGlobalPortFrom object. If the translation specifies a single port, then the value of this object is equal to the value of natAddrMapGlobalPortFrom." DEFVAL { 0 } Perreault, et al. Expires December 17, 2015 [Page 20] Internet-Draft Deprecation of NAT MIB v1 June 2015 ::= { natAddrMapEntry 14 } natAddrMapProtocol OBJECT-TYPE SYNTAX NatProtocolMap MAX-ACCESS read-create STATUS deprecated DESCRIPTION "This object specifies a bitmap of protocol identifiers." ::= { natAddrMapEntry 15 } natAddrMapInTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of inbound packets pertaining to this address map entry that were translated. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natAddrMapEntry 16 } natAddrMapOutTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of outbound packets pertaining to this address map entry that were translated. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natAddrMapEntry 17 } natAddrMapDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of packets pertaining to this address map entry that were dropped due to lack of addresses in the address pool identified by this address map. The value of this object must always be zero in case of static address map. Perreault, et al. Expires December 17, 2015 [Page 21] Internet-Draft Deprecation of NAT MIB v1 June 2015 Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natAddrMapEntry 18 } natAddrMapAddrUsed OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of addresses pertaining to this address map that are currently being used from the NAT pool. The value of this object must always be zero in the case of a static address map." ::= { natAddrMapEntry 19 } natAddrMapStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." REFERENCE "Textual Conventions for SMIv2, Section 2." DEFVAL { nonVolatile } ::= { natAddrMapEntry 20 } natAddrMapRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS deprecated DESCRIPTION "The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the natAddrMapRowStatus column is 'notReady'. None of the objects in this row may be modified while the value of this object is active(1)." REFERENCE "Textual Conventions for SMIv2, Section 2." ::= { natAddrMapEntry 21 } Perreault, et al. Expires December 17, 2015 [Page 22] Internet-Draft Deprecation of NAT MIB v1 June 2015 -- -- Address Bind section -- natAddrBindNumberOfEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object maintains a count of the number of entries that currently exist in the natAddrBindTable." ::= { natMIBObjects 5 } -- -- The NAT Address BIND Table -- natAddrBindTable OBJECT-TYPE SYNTAX SEQUENCE OF NatAddrBindEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table holds information about the currently active NAT BINDs." ::= { natMIBObjects 6 } natAddrBindEntry OBJECT-TYPE SYNTAX NatAddrBindEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry in this table holds information about an active address BIND. These entries are lost upon agent restart. This row has indexing which may create variables with more than 128 subidentifiers. Implementers of this table must be careful not to create entries that would result in OIDs which exceed the 128 subidentifier limit. Otherwise, the information cannot be accessed using SNMPv1, SNMPv2c or SNMPv3." INDEX { ifIndex, natAddrBindLocalAddrType, natAddrBindLocalAddr } ::= { natAddrBindTable 1 } NatAddrBindEntry ::= SEQUENCE { Perreault, et al. Expires December 17, 2015 [Page 23] Internet-Draft Deprecation of NAT MIB v1 June 2015 natAddrBindLocalAddrType InetAddressType, natAddrBindLocalAddr InetAddress, natAddrBindGlobalAddrType InetAddressType, natAddrBindGlobalAddr InetAddress, natAddrBindId NatBindId, natAddrBindTranslationEntity NatTranslationEntity, natAddrBindType NatAssociationType, natAddrBindMapIndex NatAddrMapId, natAddrBindSessions Gauge32, natAddrBindMaxIdleTime TimeTicks, natAddrBindCurrentIdleTime TimeTicks, natAddrBindInTranslates Counter64, natAddrBindOutTranslates Counter64 } natAddrBindLocalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This object specifies the address type used for natAddrBindLocalAddr." ::= { natAddrBindEntry 1 } natAddrBindLocalAddr OBJECT-TYPE SYNTAX InetAddress (SIZE (4|16)) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This object represents the private-realm specific network layer address, which maps to the public-realm address represented by natAddrBindGlobalAddr. The type of this address is determined by the value of the natAddrBindLocalAddrType object." ::= { natAddrBindEntry 2 } natAddrBindGlobalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object specifies the address type used for natAddrBindGlobalAddr." ::= { natAddrBindEntry 3 } natAddrBindGlobalAddr OBJECT-TYPE SYNTAX InetAddress Perreault, et al. Expires December 17, 2015 [Page 24] Internet-Draft Deprecation of NAT MIB v1 June 2015 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object represents the public-realm network layer address that maps to the private-realm network layer address represented by natAddrBindLocalAddr. The type of this address is determined by the value of the natAddrBindGlobalAddrType object." ::= { natAddrBindEntry 4 } natAddrBindId OBJECT-TYPE SYNTAX NatBindId MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object represents a bind id that is dynamically assigned to each bind by a NAT enabled device. Each bind is represented by a bind id that is unique across both, the natAddrBindTable and the natAddrPortBindTable." ::= { natAddrBindEntry 5 } natAddrBindTranslationEntity OBJECT-TYPE SYNTAX NatTranslationEntity MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object represents the direction of sessions for which this bind is applicable and the endpoint entity (source or destination) within the sessions that is subject to translation using the BIND. Orientation of the bind can be a superset of translationEntity of the address map entry which forms the basis for this bind. For example, if the translationEntity of an address map entry is outboundSrcEndPoint, the translationEntity of a bind derived from this map entry may either be outboundSrcEndPoint or it may be bidirectional (a bitmask of outboundSrcEndPoint and inboundDstEndPoint)." ::= { natAddrBindEntry 6 } natAddrBindType OBJECT-TYPE SYNTAX NatAssociationType MAX-ACCESS read-only Perreault, et al. Expires December 17, 2015 [Page 25] Internet-Draft Deprecation of NAT MIB v1 June 2015 STATUS deprecated DESCRIPTION "This object indicates whether the bind is static or dynamic." ::= { natAddrBindEntry 7 } natAddrBindMapIndex OBJECT-TYPE SYNTAX NatAddrMapId MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object is a pointer to the natAddrMapTable entry (and the parameters of that entry) which was used in creating this BIND. This object, in conjunction with the ifIndex (which identifies a unique addrMapName) points to a unique entry in the natAddrMapTable." ::= { natAddrBindEntry 8 } natAddrBindSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of sessions currently using this BIND." ::= { natAddrBindEntry 9 } natAddrBindMaxIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the maximum time for which this bind can be idle with no sessions attached to it. The value of this object is of relevance only for dynamic NAT." ::= { natAddrBindEntry 10 } natAddrBindCurrentIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "At any given instance, this object indicates the time that this bind has been idle without any sessions attached to it. Perreault, et al. Expires December 17, 2015 [Page 26] Internet-Draft Deprecation of NAT MIB v1 June 2015 The value of this object is of relevance only for dynamic NAT." ::= { natAddrBindEntry 11 } natAddrBindInTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of inbound packets that were successfully translated by using this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natAddrBindEntry 12 } natAddrBindOutTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of outbound packets that were successfully translated using this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natAddrBindEntry 13 } -- -- Address Port Bind section -- natAddrPortBindNumberOfEntries OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object maintains a count of the number of entries that currently exist in the natAddrPortBindTable." ::= { natMIBObjects 7 } -- -- The NAT Address Port Bind Table -- Perreault, et al. Expires December 17, 2015 [Page 27] Internet-Draft Deprecation of NAT MIB v1 June 2015 natAddrPortBindTable OBJECT-TYPE SYNTAX SEQUENCE OF NatAddrPortBindEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This table holds information about the currently active NAPT BINDs." ::= { natMIBObjects 8 } natAddrPortBindEntry OBJECT-TYPE SYNTAX NatAddrPortBindEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "Each entry in the this table holds information about a NAPT bind that is currently active. These entries are lost upon agent restart. This row has indexing which may create variables with more than 128 subidentifiers. Implementers of this table must be careful not to create entries which would result in OIDs that exceed the 128 subidentifier limit. Otherwise, the information cannot be accessed using SNMPv1, SNMPv2c or SNMPv3." INDEX { ifIndex, natAddrPortBindLocalAddrType, natAddrPortBindLocalAddr, natAddrPortBindLocalPort, natAddrPortBindProtocol } ::= { natAddrPortBindTable 1 } NatAddrPortBindEntry ::= SEQUENCE { natAddrPortBindLocalAddrType InetAddressType, natAddrPortBindLocalAddr InetAddress, natAddrPortBindLocalPort InetPortNumber, natAddrPortBindProtocol NatProtocolType, natAddrPortBindGlobalAddrType InetAddressType, natAddrPortBindGlobalAddr InetAddress, natAddrPortBindGlobalPort InetPortNumber, natAddrPortBindId NatBindId, natAddrPortBindTranslationEntity NatTranslationEntity, natAddrPortBindType NatAssociationType, natAddrPortBindMapIndex NatAddrMapId, natAddrPortBindSessions Gauge32, natAddrPortBindMaxIdleTime TimeTicks, natAddrPortBindCurrentIdleTime TimeTicks, natAddrPortBindInTranslates Counter64, natAddrPortBindOutTranslates Counter64 } Perreault, et al. Expires December 17, 2015 [Page 28] Internet-Draft Deprecation of NAT MIB v1 June 2015 natAddrPortBindLocalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This object specifies the address type used for natAddrPortBindLocalAddr." ::= { natAddrPortBindEntry 1 } natAddrPortBindLocalAddr OBJECT-TYPE SYNTAX InetAddress (SIZE(4|16)) MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This object represents the private-realm specific network layer address which, in conjunction with natAddrPortBindLocalPort, maps to the public-realm network layer address and transport id represented by natAddrPortBindGlobalAddr and natAddrPortBindGlobalPort respectively. The type of this address is determined by the value of the natAddrPortBindLocalAddrType object." ::= { natAddrPortBindEntry 2 } natAddrPortBindLocalPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "For a protocol value TCP or UDP, this object represents the private-realm specific port number. On the other hand, for ICMP a bind is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the private-realm specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. This object, together with natAddrPortBindProtocol, natAddrPortBindLocalAddrType, and natAddrPortBindLocalAddr, constitutes a session endpoint in the private realm. A bind entry binds a private realm specific endpoint to a public realm specific endpoint, as represented by the tuple of (natAddrPortBindGlobalPort, natAddrPortBindProtocol, natAddrPortBindGlobalAddrType, and Perreault, et al. Expires December 17, 2015 [Page 29] Internet-Draft Deprecation of NAT MIB v1 June 2015 natAddrPortBindGlobalAddr)." ::= { natAddrPortBindEntry 3 } natAddrPortBindProtocol OBJECT-TYPE SYNTAX NatProtocolType MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This object specifies a protocol identifier. If the value of this object is none(1), then this bind entry applies to all IP traffic. Any other value of this object specifies the class of IP traffic to which this BIND applies." ::= { natAddrPortBindEntry 4 } natAddrPortBindGlobalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object specifies the address type used for natAddrPortBindGlobalAddr." ::= { natAddrPortBindEntry 5 } natAddrPortBindGlobalAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object represents the public-realm specific network layer address that, in conjunction with natAddrPortBindGlobalPort, maps to the private-realm network layer address and transport id represented by natAddrPortBindLocalAddr and natAddrPortBindLocalPort, respectively. The type of this address is determined by the value of the natAddrPortBindGlobalAddrType object." ::= { natAddrPortBindEntry 6 } natAddrPortBindGlobalPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS deprecated DESCRIPTION "For a protocol value TCP or UDP, this object represents the public-realm specific port number. On the other Perreault, et al. Expires December 17, 2015 [Page 30] Internet-Draft Deprecation of NAT MIB v1 June 2015 hand, for ICMP a bind is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the public-realm specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. This object, together with natAddrPortBindProtocol, natAddrPortBindGlobalAddrType, and natAddrPortBindGlobalAddr, constitutes a session endpoint in the public realm. A bind entry binds a public realm specific endpoint to a private realm specific endpoint, as represented by the tuple of (natAddrPortBindLocalPort, natAddrPortBindProtocol, natAddrPortBindLocalAddrType, and natAddrPortBindLocalAddr)." ::= { natAddrPortBindEntry 7 } natAddrPortBindId OBJECT-TYPE SYNTAX NatBindId MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object represents a bind id that is dynamically assigned to each bind by a NAT enabled device. Each bind is represented by a unique bind id across both the natAddrBindTable and the natAddrPortBindTable." ::= { natAddrPortBindEntry 8 } natAddrPortBindTranslationEntity OBJECT-TYPE SYNTAX NatTranslationEntity MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object represents the direction of sessions for which this bind is applicable and the entity (source or destination) within the sessions that is subject to translation with the BIND. Orientation of the bind can be a superset of the translationEntity of the address map entry that forms the basis for this bind. For example, if the translationEntity of an address map entry is outboundSrcEndPoint, the translationEntity of a bind derived from this map entry may either be outboundSrcEndPoint or may be bidirectional (a bitmask of Perreault, et al. Expires December 17, 2015 [Page 31] Internet-Draft Deprecation of NAT MIB v1 June 2015 outboundSrcEndPoint and inboundDstEndPoint)." ::= { natAddrPortBindEntry 9 } natAddrPortBindType OBJECT-TYPE SYNTAX NatAssociationType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates whether the bind is static or dynamic." ::= { natAddrPortBindEntry 10 } natAddrPortBindMapIndex OBJECT-TYPE SYNTAX NatAddrMapId MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object is a pointer to the natAddrMapTable entry (and the parameters of that entry) used in creating this BIND. This object, in conjunction with the ifIndex (which identifies a unique addrMapName), points to a unique entry in the natAddrMapTable." ::= { natAddrPortBindEntry 11 } natAddrPortBindSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "Number of sessions currently using this BIND." ::= { natAddrPortBindEntry 12 } natAddrPortBindMaxIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates the maximum time for which this bind can be idle without any sessions attached to it. The value of this object is of relevance only for dynamic NAT." ::= { natAddrPortBindEntry 13 } natAddrPortBindCurrentIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only Perreault, et al. Expires December 17, 2015 [Page 32] Internet-Draft Deprecation of NAT MIB v1 June 2015 STATUS deprecated DESCRIPTION "At any given instance, this object indicates the time that this bind has been idle without any sessions attached to it. The value of this object is of relevance only for dynamic NAT." ::= { natAddrPortBindEntry 14 } natAddrPortBindInTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of inbound packets that were translated as per this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natAddrPortBindEntry 15 } natAddrPortBindOutTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of outbound packets that were translated as per this bind entry. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natAddrPortBindEntry 16 } -- -- The Session Table -- natSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF NatSessionEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The (conceptual) table containing one entry for each Perreault, et al. Expires December 17, 2015 [Page 33] Internet-Draft Deprecation of NAT MIB v1 June 2015 NAT session currently active on this NAT device." ::= { natMIBObjects 9 } natSessionEntry OBJECT-TYPE SYNTAX NatSessionEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "An entry (conceptual row) containing information about an active NAT session on this NAT device. These entries are lost upon agent restart." INDEX { ifIndex, natSessionIndex } ::= { natSessionTable 1 } NatSessionEntry ::= SEQUENCE { natSessionIndex NatSessionId, natSessionPrivateSrcEPBindId NatBindIdOrZero, natSessionPrivateSrcEPBindMode NatBindMode, natSessionPrivateDstEPBindId NatBindIdOrZero, natSessionPrivateDstEPBindMode NatBindMode, natSessionDirection INTEGER, natSessionUpTime TimeTicks, natSessionAddrMapIndex NatAddrMapId, natSessionProtocolType NatProtocolType, natSessionPrivateAddrType InetAddressType, natSessionPrivateSrcAddr InetAddress, natSessionPrivateSrcPort InetPortNumber, natSessionPrivateDstAddr InetAddress, natSessionPrivateDstPort InetPortNumber, natSessionPublicAddrType InetAddressType, natSessionPublicSrcAddr InetAddress, natSessionPublicSrcPort InetPortNumber, natSessionPublicDstAddr InetAddress, natSessionPublicDstPort InetPortNumber, natSessionMaxIdleTime TimeTicks, natSessionCurrentIdleTime TimeTicks, natSessionInTranslates Counter64, natSessionOutTranslates Counter64 } natSessionIndex OBJECT-TYPE SYNTAX NatSessionId MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The session ID for this NAT session." ::= { natSessionEntry 1 } Perreault, et al. Expires December 17, 2015 [Page 34] Internet-Draft Deprecation of NAT MIB v1 June 2015 natSessionPrivateSrcEPBindId OBJECT-TYPE SYNTAX NatBindIdOrZero MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The bind id associated between private and public source end points. In the case of Symmetric-NAT, this should be set to zero." ::= { natSessionEntry 2 } natSessionPrivateSrcEPBindMode OBJECT-TYPE SYNTAX NatBindMode MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates whether the bind indicated by the object natSessionPrivateSrcEPBindId is an address bind or an address port bind." ::= { natSessionEntry 3 } natSessionPrivateDstEPBindId OBJECT-TYPE SYNTAX NatBindIdOrZero MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The bind id associated between private and public destination end points." ::= { natSessionEntry 4 } natSessionPrivateDstEPBindMode OBJECT-TYPE SYNTAX NatBindMode MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object indicates whether the bind indicated by the object natSessionPrivateDstEPBindId is an address bind or an address port bind." ::= { natSessionEntry 5 } natSessionDirection OBJECT-TYPE SYNTAX INTEGER { inbound (1), outbound (2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION Perreault, et al. Expires December 17, 2015 [Page 35] Internet-Draft Deprecation of NAT MIB v1 June 2015 "The direction of this session with respect to the local network. 'inbound' indicates that this session was initiated from the public network into the private network. 'outbound' indicates that this session was initiated from the private network into the public network." ::= { natSessionEntry 6 } natSessionUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The up time of this session in one-hundredths of a second." ::= { natSessionEntry 7 } natSessionAddrMapIndex OBJECT-TYPE SYNTAX NatAddrMapId MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object is a pointer to the natAddrMapTable entry (and the parameters of that entry) used in creating this session. This object, in conjunction with the ifIndex (which identifies a unique addrMapName), points to a unique entry in the natAddrMapTable." ::= { natSessionEntry 8 } natSessionProtocolType OBJECT-TYPE SYNTAX NatProtocolType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The protocol type of this session." ::= { natSessionEntry 9 } natSessionPrivateAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object specifies the address type used for natSessionPrivateSrcAddr and natSessionPrivateDstAddr." ::= { natSessionEntry 10 } natSessionPrivateSrcAddr OBJECT-TYPE SYNTAX InetAddress Perreault, et al. Expires December 17, 2015 [Page 36] Internet-Draft Deprecation of NAT MIB v1 June 2015 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The source IP address of the session endpoint that lies in the private network. The value of this object must be zero only when the natSessionPrivateSrcEPBindId object has a zero value. When the value of this object is zero, the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPrivateAddrType object." ::= { natSessionEntry 11 } natSessionPrivateSrcPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS deprecated DESCRIPTION "When the value of protocol is TCP or UDP, this object represents the source port in the first packet of session while in private-realm. On the other hand, when the protocol is ICMP, a NAT session is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the private-realm specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. The value of this object must be zero when the natSessionPrivateSrcEPBindId object has zero value and value of natSessionPrivateSrcEPBindMode is addressPortBind(2). In such a case, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort, or ICMP identifier) of the session tuple in either the public realm or the private realm." ::= { natSessionEntry 12 } natSessionPrivateDstAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The destination IP address of the session endpoint that Perreault, et al. Expires December 17, 2015 [Page 37] Internet-Draft Deprecation of NAT MIB v1 June 2015 lies in the private network. The value of this object must be zero when the natSessionPrivateDstEPBindId object has a zero value. In such a scenario, the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPrivateAddrType object." ::= { natSessionEntry 13 } natSessionPrivateDstPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS deprecated DESCRIPTION "When the value of protocol is TCP or UDP, this object represents the destination port in the first packet of session while in private-realm. On the other hand, when the protocol is ICMP, this object is not relevant and should be set to zero. The value of this object must be zero when the natSessionPrivateDstEPBindId object has a zero value and natSessionPrivateDstEPBindMode is set to addressPortBind(2). In such a case, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort, or ICMP identifier) of the session tuple in either the public realm or the private realm." ::= { natSessionEntry 14 } natSessionPublicAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This object specifies the address type used for natSessionPublicSrcAddr and natSessionPublicDstAddr." ::= { natSessionEntry 15 } natSessionPublicSrcAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS deprecated DESCRIPTION Perreault, et al. Expires December 17, 2015 [Page 38] Internet-Draft Deprecation of NAT MIB v1 June 2015 "The source IP address of the session endpoint that lies in the public network. The value of this object must be zero when the natSessionPrivateSrcEPBindId object has a zero value. In such a scenario, the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPublicAddrType object." ::= { natSessionEntry 16 } natSessionPublicSrcPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS deprecated DESCRIPTION "When the value of protocol is TCP or UDP, this object represents the source port in the first packet of session while in public-realm. On the other hand, when protocol is ICMP, a NAT session is created only for query/response type ICMP messages such as ICMP echo, Timestamp, and Information request messages, and this object represents the public-realm specific identifier in the ICMP message, as defined in RFC 792 for ICMPv4 and in RFC 2463 for ICMPv6. The value of this object must be zero when the natSessionPrivateSrcEPBindId object has a zero value and natSessionPrivateSrcEPBindMode is set to addressPortBind(2). In such a scenario, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort or ICMP identifier) of the session tuple in either the public realm or the private realm." ::= { natSessionEntry 17 } natSessionPublicDstAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The destination IP address of the session endpoint that lies in the public network. Perreault, et al. Expires December 17, 2015 [Page 39] Internet-Draft Deprecation of NAT MIB v1 June 2015 The value of this object must be non-zero when the natSessionPrivateDstEPBindId object has a non-zero value. If the value of this object and the corresponding natSessionPrivateDstEPBindId object value is zero, then the NAT session lookup will match any IP address to this field. The type of this address is determined by the value of the natSessionPublicAddrType object." ::= { natSessionEntry 18 } natSessionPublicDstPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS deprecated DESCRIPTION "When the value of protocol is TCP or UDP, this object represents the destination port in the first packet of session while in public-realm. On the other hand, when the protocol is ICMP, this object is not relevant for translation and should be zero. The value of this object must be zero when the natSessionPrivateDstEPBindId object has a zero value and natSessionPrivateDstEPBindMode is addressPortBind(2). In such a scenario, the NAT session lookup will match any port number to this field. The value of this object must be zero when the object is not a representative field (SrcPort, DstPort, or ICMP identifier) of the session tuple in either the public realm or the private realm." ::= { natSessionEntry 19 } natSessionMaxIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The max time for which this session can be idle without detecting a packet." ::= { natSessionEntry 20 } natSessionCurrentIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS deprecated Perreault, et al. Expires December 17, 2015 [Page 40] Internet-Draft Deprecation of NAT MIB v1 June 2015 DESCRIPTION "The time since a packet belonging to this session was last detected." ::= { natSessionEntry 21 } natSessionInTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of inbound packets that were translated for this session. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natSessionEntry 22 } natSessionOutTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of outbound packets that were translated for this session. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natSessionEntry 23 } -- -- The Protocol table -- natProtocolTable OBJECT-TYPE SYNTAX SEQUENCE OF NatProtocolEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The (conceptual) table containing per protocol NAT statistics." ::= { natMIBObjects 10 } natProtocolEntry OBJECT-TYPE SYNTAX NatProtocolEntry Perreault, et al. Expires December 17, 2015 [Page 41] Internet-Draft Deprecation of NAT MIB v1 June 2015 MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "An entry (conceptual row) containing NAT statistics pertaining to a particular protocol." INDEX { natProtocol } ::= { natProtocolTable 1 } NatProtocolEntry ::= SEQUENCE { natProtocol NatProtocolType, natProtocolInTranslates Counter64, natProtocolOutTranslates Counter64, natProtocolDiscards Counter64 } natProtocol OBJECT-TYPE SYNTAX NatProtocolType MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "This object represents the protocol pertaining to which parameters are reported." ::= { natProtocolEntry 1 } natProtocolInTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of inbound packets pertaining to the protocol identified by natProtocol that underwent NAT. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natProtocolEntry 2 } natProtocolOutTranslates OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of outbound packets pertaining to the protocol identified by natProtocol that underwent NAT. Discontinuities in the value of this counter can occur at reinitialization of the management system and at Perreault, et al. Expires December 17, 2015 [Page 42] Internet-Draft Deprecation of NAT MIB v1 June 2015 other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natProtocolEntry 3 } natProtocolDiscards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The number of packets pertaining to the protocol identified by natProtocol that had to be rejected/dropped due to lack of resources. These rejections could be due to session timeout, resource unavailability, lack of address space, etc. Discontinuities in the value of this counter can occur at reinitialization of the management system and at other times, as indicated by the value of ifCounterDiscontinuityTime on the relevant interface." ::= { natProtocolEntry 4 } -- -- Notifications section -- natMIBNotifications OBJECT IDENTIFIER ::= { natMIB 0 } -- -- Notifications -- natPacketDiscard NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS deprecated DESCRIPTION "This notification is generated when IP packets are discarded by the NAT function; e.g., due to lack of mapping space when NAT is out of addresses or ports. Note that the generation of natPacketDiscard notifications is throttled by the agent, as specified by the 'natNotifThrottlingInterval' object." ::= { natMIBNotifications 1 } -- -- Conformance information. Perreault, et al. Expires December 17, 2015 [Page 43] Internet-Draft Deprecation of NAT MIB v1 June 2015 -- natMIBConformance OBJECT IDENTIFIER ::= { natMIB 2 } natMIBGroups OBJECT IDENTIFIER ::= { natMIBConformance 1 } natMIBCompliances OBJECT IDENTIFIER ::= { natMIBConformance 2 } -- -- Units of conformance -- natConfigGroup OBJECT-GROUP OBJECTS { natInterfaceRealm, natInterfaceServiceType, natInterfaceStorageType, natInterfaceRowStatus, natAddrMapName, natAddrMapEntryType, natAddrMapTranslationEntity, natAddrMapLocalAddrType, natAddrMapLocalAddrFrom, natAddrMapLocalAddrTo, natAddrMapLocalPortFrom, natAddrMapLocalPortTo, natAddrMapGlobalAddrType, natAddrMapGlobalAddrFrom, natAddrMapGlobalAddrTo, natAddrMapGlobalPortFrom, natAddrMapGlobalPortTo, natAddrMapProtocol, natAddrMapStorageType, natAddrMapRowStatus, natBindDefIdleTimeout, natUdpDefIdleTimeout, natIcmpDefIdleTimeout, natOtherDefIdleTimeout, natTcpDefIdleTimeout, natTcpDefNegTimeout, natNotifThrottlingInterval } STATUS deprecated DESCRIPTION "A collection of configuration-related information required to support management of devices supporting NAT." ::= { natMIBGroups 1 } natTranslationGroup OBJECT-GROUP OBJECTS { natAddrBindNumberOfEntries, Perreault, et al. Expires December 17, 2015 [Page 44] Internet-Draft Deprecation of NAT MIB v1 June 2015 natAddrBindGlobalAddrType, natAddrBindGlobalAddr, natAddrBindId, natAddrBindTranslationEntity, natAddrBindType, natAddrBindMapIndex, natAddrBindSessions, natAddrBindMaxIdleTime, natAddrBindCurrentIdleTime, natAddrBindInTranslates, natAddrBindOutTranslates, natAddrPortBindNumberOfEntries, natAddrPortBindGlobalAddrType, natAddrPortBindGlobalAddr, natAddrPortBindGlobalPort, natAddrPortBindId, natAddrPortBindTranslationEntity, natAddrPortBindType, natAddrPortBindMapIndex, natAddrPortBindSessions, natAddrPortBindMaxIdleTime, natAddrPortBindCurrentIdleTime, natAddrPortBindInTranslates, natAddrPortBindOutTranslates, natSessionPrivateSrcEPBindId, natSessionPrivateSrcEPBindMode, natSessionPrivateDstEPBindId, natSessionPrivateDstEPBindMode, natSessionDirection, natSessionUpTime, natSessionAddrMapIndex, natSessionProtocolType, natSessionPrivateAddrType, natSessionPrivateSrcAddr, natSessionPrivateSrcPort, natSessionPrivateDstAddr, natSessionPrivateDstPort, natSessionPublicAddrType, natSessionPublicSrcAddr, natSessionPublicSrcPort, natSessionPublicDstAddr, natSessionPublicDstPort, natSessionMaxIdleTime, natSessionCurrentIdleTime, natSessionInTranslates, natSessionOutTranslates } STATUS deprecated Perreault, et al. Expires December 17, 2015 [Page 45] Internet-Draft Deprecation of NAT MIB v1 June 2015 DESCRIPTION "A collection of BIND-related objects required to support management of devices supporting NAT." ::= { natMIBGroups 2 } natStatsInterfaceGroup OBJECT-GROUP OBJECTS { natInterfaceInTranslates, natInterfaceOutTranslates, natInterfaceDiscards } STATUS deprecated DESCRIPTION "A collection of NAT statistics associated with the interface on which NAT is configured, to aid troubleshooting/monitoring of the NAT operation." ::= { natMIBGroups 3 } natStatsProtocolGroup OBJECT-GROUP OBJECTS { natProtocolInTranslates, natProtocolOutTranslates, natProtocolDiscards } STATUS deprecated DESCRIPTION "A collection of protocol specific NAT statistics, to aid troubleshooting/monitoring of NAT operation." ::= { natMIBGroups 4 } natStatsAddrMapGroup OBJECT-GROUP OBJECTS { natAddrMapInTranslates, natAddrMapOutTranslates, natAddrMapDiscards, natAddrMapAddrUsed } STATUS deprecated DESCRIPTION "A collection of address map specific NAT statistics, to aid troubleshooting/monitoring of NAT operation." ::= { natMIBGroups 5 } natMIBNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { natPacketDiscard } STATUS deprecated DESCRIPTION "A collection of notifications generated by devices supporting this MIB." ::= { natMIBGroups 6 } -- -- Compliance statements Perreault, et al. Expires December 17, 2015 [Page 46] Internet-Draft Deprecation of NAT MIB v1 June 2015 -- natMIBFullCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "When this MIB is implemented with support for read-create, then such an implementation can claim full compliance. Such devices can then be both monitored and configured with this MIB. The following index objects cannot be added as OBJECT clauses but nevertheless have the compliance requirements: " -- OBJECT natAddrBindLocalAddrType -- SYNTAX InetAddressType { ipv4(1), ipv6(2) } -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending -- on its support for IPv4 and IPv6." -- OBJECT natAddrBindLocalAddr -- SYNTAX InetAddress (SIZE(4|16)) -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending -- on its support for IPv4 and IPv6." -- OBJECT natAddrPortBindLocalAddrType -- SYNTAX InetAddressType { ipv4(1), ipv6(2) } -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending -- on its support for IPv4 and IPv6." -- OBJECT natAddrPortBindLocalAddr -- SYNTAX InetAddress (SIZE(4|16)) -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending -- on its support for IPv4 and IPv6." MODULE IF-MIB -- The interfaces MIB, RFC2863 MANDATORY-GROUPS { ifCounterDiscontinuityGroup } MODULE -- this module Perreault, et al. Expires December 17, 2015 [Page 47] Internet-Draft Deprecation of NAT MIB v1 June 2015 MANDATORY-GROUPS { natConfigGroup, natTranslationGroup, natStatsInterfaceGroup } GROUP natStatsProtocolGroup DESCRIPTION "This group is optional." GROUP natStatsAddrMapGroup DESCRIPTION "This group is optional." GROUP natMIBNotificationGroup DESCRIPTION "This group is optional." OBJECT natAddrMapLocalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapLocalAddrFrom SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapLocalAddrTo SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapGlobalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapGlobalAddrFrom SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." Perreault, et al. Expires December 17, 2015 [Page 48] Internet-Draft Deprecation of NAT MIB v1 June 2015 OBJECT natAddrMapGlobalAddrTo SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrBindGlobalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrBindGlobalAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrPortBindGlobalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrPortBindGlobalAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPrivateAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPrivateSrcAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." Perreault, et al. Expires December 17, 2015 [Page 49] Internet-Draft Deprecation of NAT MIB v1 June 2015 OBJECT natSessionPrivateDstAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPublicAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPublicSrcAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPublicDstAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." ::= { natMIBCompliances 1 } natMIBReadOnlyCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "When this MIB is implemented without support for read-create (i.e., in read-only mode), then such an implementation can claim read-only compliance. Such a device can then be monitored but cannot be configured with this MIB. The following index objects cannot be added as OBJECT clauses but nevertheless have the compliance requirements: " -- OBJECT natAddrBindLocalAddrType -- SYNTAX InetAddressType { ipv4(1), ipv6(2) } -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending Perreault, et al. Expires December 17, 2015 [Page 50] Internet-Draft Deprecation of NAT MIB v1 June 2015 -- on its support for IPv4 and IPv6." -- OBJECT natAddrBindLocalAddr -- SYNTAX InetAddress (SIZE(4|16)) -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending -- on its support for IPv4 and IPv6." -- OBJECT natAddrPortBindLocalAddrType -- SYNTAX InetAddressType { ipv4(1), ipv6(2) } -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending -- on its support for IPv4 and IPv6." -- OBJECT natAddrPortBindLocalAddr -- SYNTAX InetAddress (SIZE(4|16)) -- DESCRIPTION -- "An implementation is required to support -- global IPv4 and/or IPv6 addresses, depending -- on its support for IPv4 and IPv6." MODULE IF-MIB -- The interfaces MIB, RFC2863 MANDATORY-GROUPS { ifCounterDiscontinuityGroup } MODULE -- this module MANDATORY-GROUPS { natConfigGroup, natTranslationGroup, natStatsInterfaceGroup } GROUP natStatsProtocolGroup DESCRIPTION "This group is optional." GROUP natStatsAddrMapGroup DESCRIPTION "This group is optional." GROUP natMIBNotificationGroup DESCRIPTION "This group is optional." OBJECT natInterfaceRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." Perreault, et al. Expires December 17, 2015 [Page 51] Internet-Draft Deprecation of NAT MIB v1 June 2015 OBJECT natAddrMapLocalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapLocalAddrFrom SYNTAX InetAddress (SIZE(4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapLocalAddrTo SYNTAX InetAddress (SIZE(4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapGlobalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapGlobalAddrFrom SYNTAX InetAddress (SIZE(4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrMapGlobalAddrTo SYNTAX InetAddress (SIZE(4|16)) MIN-ACCESS read-only DESCRIPTION "Write access is not required. An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." Perreault, et al. Expires December 17, 2015 [Page 52] Internet-Draft Deprecation of NAT MIB v1 June 2015 OBJECT natAddrMapRowStatus SYNTAX RowStatus { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and active is the only status that needs to be supported." OBJECT natAddrBindGlobalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrBindGlobalAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrPortBindGlobalAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natAddrPortBindGlobalAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPrivateAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPrivateSrcAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." Perreault, et al. Expires December 17, 2015 [Page 53] Internet-Draft Deprecation of NAT MIB v1 June 2015 OBJECT natSessionPrivateDstAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPublicAddrType SYNTAX InetAddressType { ipv4(1), ipv6(2) } DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPublicSrcAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." OBJECT natSessionPublicDstAddr SYNTAX InetAddress (SIZE(4|16)) DESCRIPTION "An implementation is required to support global IPv4 and/or IPv6 addresses, depending on its support for IPv4 and IPv6." ::= { natMIBCompliances 2 } END 5. Security Considerations All objects in this MIB module have been deprecated. As a result, security considerations in [I-D.ietf-behave-nat-mib-v2] apply instead. Amongst other matters, these considerations cover the case where both this MIB module and NAT-MIB-V2 are present. In fact, such a situation is unlikely because [RFC4008], as a MIB module oriented toward configuration, was overtaken by events and saw little implementation. 6. IANA Considerations IANA has assigned object identifier 123 to the natMIB module, with prefix iso.org.dod.internet.mgmt.mib-2 in the Network Management Parameters registry [SMI-NUMBERS]. Perreault, et al. Expires December 17, 2015 [Page 54] Internet-Draft Deprecation of NAT MIB v1 June 2015 IANA is requested to mark that identifier as OBSOLETE and to update the reference from [RFC4008] to the present document. 7. References 7.1. Normative References [I-D.ietf-behave-nat-mib-v2] Perrault, S., Tsou, T., Sivakumar, S., and T. Taylor, "Definitions of Managed Objects for Network Address Translators (NAT), Version 2", June 2015. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", STD 62, RFC 3411, December 2002. [RFC3414] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", STD 62, RFC 3414, December 2002. [RFC3826] Blumenthal, U., Maino, F., and K. McCloghrie, "The Advanced Encryption Standard (AES) Cipher Algorithm in the SNMP User-based Security Model", RFC 3826, June 2004. [RFC4001] Daniele, M., Haberman, B., Routhier, S., and J. Schoenwaelder, "Textual Conventions for Internet Network Addresses", RFC 4001, February 2005. [RFC5591] Harrington, D. and W. Hardaker, "Transport Security Model for the Simple Network Management Protocol (SNMP)", STD 78, RFC 5591, June 2009. Perreault, et al. Expires December 17, 2015 [Page 55] Internet-Draft Deprecation of NAT MIB v1 June 2015 [RFC5592] Harrington, D., Salowey, J., and W. Hardaker, "Secure Shell Transport Model for the Simple Network Management Protocol (SNMP)", RFC 5592, June 2009. [RFC6353] Hardaker, W., "Transport Layer Security (TLS) Transport Model for the Simple Network Management Protocol (SNMP)", STD 78, RFC 6353, July 2011. 7.2. Informative References [RFC2663] Srisuresh, P. and M. Holdrege, "IP Network Address Translator (NAT) Terminology and Considerations", RFC 2663, August 1999. [RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network Address Translator (Traditional NAT)", RFC 3022, January 2001. [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. [RFC4008] Rohit, R., Srisuresh, P., Raghunarayan, R., Pai, N., and C. Wang, "Definitions of Managed Objects for Network Address Translators (NAT)", RFC 4008, March 2005. [SMI-NUMBERS] "Network Management Parameters registry at IANA", . Authors' Addresses Simon Perreault Jive Communications Quebec, QC Canada Email: sperreault@jive.com Tina Tsou Huawei Technologies Bantian, Longgang District Shenzhen 518129 PR China Email: tina.tsou.zouting@huawei.com Perreault, et al. Expires December 17, 2015 [Page 56] Internet-Draft Deprecation of NAT MIB v1 June 2015 Senthil Sivakumar Cisco Systems 7100-8 Kit Creek Road Research Triangle Park, North Carolina 27709 USA Phone: +1 919 392 5158 Email: ssenthil@cisco.com Tom Taylor PT Taylor Consulting Ottawa Canada Email: tom.taylor.stds@gmail.com Perreault, et al. Expires December 17, 2015 [Page 57]