HTTP/1.1 200 OK Date: Tue, 09 Apr 2002 08:56:18 GMT Server: Apache/1.3.20 (Unix) Last-Modified: Thu, 10 Feb 2000 14:07:22 GMT ETag: "2e7975-bdc6-38a2c61a" Accept-Ranges: bytes Content-Length: 48582 Connection: close Content-Type: text/plain Network Working Group E. Duros Internet-Draft W. Dabbous Feb 2000 INRIA Sophia-Antipolis H. Izumiyama N. Fujii WIDE Y. Zhang HRL A Link Layer Tunneling Mechanism for Unidirectional Links Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet- Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. A version of this draft document is intended for submission to the RFC editor as a Proposed Standard for the Internet Community. Note to the RFC editor Please replace all references to rfcXXXX with references to the new GRE specification when it is published as Proposed Standard. It currently exists as . The entry in the "References" section may also need updating at this time. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 1] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Abstract This document describes a mechanism to emulate bidirectional connectivity between nodes that are directly connected by a unidirectional link. The "receiver" uses a link layer tunneling mechanism to forward datagrams to "feeds" over a separate bidirectional IP network. As it is implemented at the link layer, protocols in addition to IP may also be supported by this mechanism. 1. Introduction Internet routing and upper layer protocols assume that links are bidirectional, i.e., directly connected hosts can communicate with each other over the same link. This document describes a link layer tunneling mechanism that allows nodes which are directly connected by a unidirectional link (feeds and receivers, see Section 2 for terminology) to send datagrams as if they were connected to a bidirectional link. We present a generic topology with a tunneling mechanism that supports multiple feeds and receivers. The tunneling mechanism requires that all nodes have an additional interface to an IP interconnected infrastructure. The tunneling mechanism is implemented at the link layer of the interface of every node connected to the unidirectional link. The aim is to hide from higher layers, i.e. the network layer and above, the unidirectional nature of the link. The tunneling mechanism also includes an automatic tunnel configuration protocol that allows nodes to come up/down at any time. Generic Routing Encapsulation [rfcXXXX] is suggested as the tunneling mechanism as it provides a means for carrying IP, ARP datagrams, and any other layer-3 protocol between nodes. The tunneling mechanism described in this document was discussed and agreed upon by the UDLR working group. 2. Terminology Unidirectional link (UDL): A one way transmission link, e.g. a broadcast satellite link. Receiver: A router that has receive-only connectivity to a UDL. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 2] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Send-only feed: A router that has send-only connectivity to a UDL. Receive capable feed: A router that has send-and-receive connectivity to a UDL. Feed: A send-only or a receive capable feed. Node: A receiver or a feed. 3. Topology Feeds and receivers are connected via a unidirectional link. Send- only feeds can only send data over this unidirectional link, and receivers can only receive data from it. Receive capable feeds have both send and receive capabilities. This mechanism has been designed to work with any topology with any number of receivers and one or more feeds. However, it is expected that the number of feeds will be small. In particular, the special case of a single send-only feed and multiple receivers is among the topologies supported. A receiver has several interfaces, a receive-only interface and one or more additional bidirectional communication interfaces. A receiver MUST be a router. A feed has several interfaces, a send-only or a send-and-receive capable interface connected to the unidirectional link and one or more additional bidirectional communication interfaces. A feed MUST be a router. Tunnels are constructed between the bidirectional interfaces of nodes, so these interfaces must be interconnected by an IP infrastructure. In this document we assume that that infrastructure is the Internet. Figure 1 depicts a generic topology with several feeds and several receivers. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 3] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Unidirectional Link ---->---------->------------------->------ | | | | |f1u |f2u |r2u |r1u -------- -------- -------- -------- ---------- |Feed 1| |Feed 2| |Recv 2| |Recv 1|---|subnet A| -------- -------- -------- -------- ---------- |f1b |f2b |r2b |r1b | | | | | | ---------------------------------------------------- | Internet | ---------------------------------------------------- Figure 1: Generic topology f1u (resp. f2u) is the IP address of the 'Feed 1' (resp. Feed 2) send-only interface. f1b (resp. f2b) is the IP address of the 'Feed 1' (resp. Feed 2) bidirectional interface connected to the Internet. r1u (resp. r2u) is the IP address of the 'Receiver 1' (resp. Receiver 2) receive-only interface. r1b (resp. r2b) is the IP address of the 'Receiver 1' (resp. Receiver 2) bidirectional interface connected to the Internet. Subnet A is a local area network connected to recv1. Note that nodes have IP addresses on their unidirectional and their bidirectional interfaces. The addresses on the unidirectional interfaces (f1u, f2u, r1u, r2u) will be drawn from the same IP network. In general the addresses on the bidirectional interfaces (f1b, f2b, r1b, r2b) will be drawn from different IP networks, and the Internet will route between them. 4. Problems related to unidirectional links Receive-only interfaces are "dumb" and send-only interfaces are "deaf". Thus a datagram passed to the link layer driver of a receive-only interface is simply discarded. The link layer of a send-only interface never receives anything. The network layer has no knowledge of the underlying transmission technology except that it considers its access as bidirectional. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 4] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Basically, for outgoing datagrams, the network layer selects the correct first hop on the connected network according to a routing table and passes the packet(s) to the appropriate link layer driver. Referring to Figure 1, Recv 1 and Feed 1 belong to the same network. However, if Recv 1 initiates a 'ping f1u', it cannot get a response from Feed 1. The network layer of Recv 1 delivers the packet to the driver of the receive-only interface, which obviously cannot send it to the feed. Most protocols in the Internet assume that links are bidirectional. In particular, routing protocols used by directly connected routers no longer behave properly in the presence of a unidirectional link. 5. Emulating a broadcast bidirectional network The simplest solution is to emulate a broadcast capable link layer network. This will allow the immediate deployment of existing higher level protocols without change. Though other network structures, such as NBMA, could also be emulated, a broadcast network is more generally useful. Though a layer 3 network could be emulated, a link layer network allows the immediate use of any other network layer protocols, and most particularly allows the immediate use of ARP. A link layer (LL) tunneling mechanism which emulates bidirectional connectivity in the presence of a unidirectional link will be described in the next Section. We first consider the various communication scenarios which characterize a broadcast network in order to define what functionalities the link layer tunneling mechanism has to perform in order to emulate a bidirectional broadcast link. Here we enumerate the scenarios which would be feasible on a broadcast network, i.e. if feeds and receivers were connected by a bidirectional broadcast link: Scenario 1: A receiver can send a packet to a feed (point-to-point communication between a receiver and a feed). Scenario 2: A receiver can send a broadcast/multicast packet on the link to all nodes (point-to-multipoint). Scenario 3: A receiver can send a packet to another receiver (point- to-point communication between two receivers). Scenario 4: A feed can send a packet to a send-only feed (point-to- point communication between two feeds). Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 5] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Scenario 5: A feed can send a broadcast/multicast packet on the link to all nodes (point-to-multipoint). Scenario 6: A feed can send a packet to a receiver or a receive capable feed. These scenarios are possible on a broadcast network. Scenario 6 is already feasible on the unidirectional link. The link layer tunneling mechanism should therefore provide the functionality to support scenarios 1 to 5. Note that regular IP forwarding over such an emulated network (i.e. using the emulated network as a transit network) works correctly; the next hop address at the receiver will be the unidirectional link address of another router (a feed or a receiver) which will then relay the packet. 6. Link layer tunneling mechanism This link layer tunneling mechanism operates underneath the network layer. Its aim is to emulate bidirectional link layer connectivity. This is transparent to the network layer: the link appears and behaves to the network layer as if it was bidirectional. Figure 2 depicts a layered representation of the link layer tunneling mechanism in the case of Scenario 1. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 6] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Send-only Feed Receiver decapsulation encapsulation /-----***************----\ /-->---***************--\ | | | | | | | | --|---------------------- | | ---------------------|--- | | f1b | f1u | | | | x r1u | r1b | | | | | ^ | | IP | | | | v | | ^ | | | v | | | | | | | | | | | | | | v | | | |-|---------|-------|---| | | |----|------|--------|--| | | | | | | ^ | | | | | | | | | | | LL | | | | | | | | | | | | | | | | | | | | | O------/ \<------O | | | |-|---------|-----------| |-----------|--------|--| | | | | | | | | | | | | PHY | | | | | | | | | | v | | | | | | | | | | | --|-----------|---------- ----------|----------|--- | Bidir | Send-Only Recv-Only | Bidir | ^ Interf | Interf UDL Interf | Interf | | \------------>------->------------/ | \----------------------<------------------------<--------/ Bidirectional network x : IP layer at the receiver generates a datagram to be forwarded on the receive-only interface. O : Entry point where the link layer tunneling mechanism is triggered. Figure 2: Scenario 1 using the LL Tunneling Mechanism 6.1. Tunneling mechanism on the receiver On the receiver, a datagram is delivered to the link layer of the unidirectional interface for transmission (see Figure 2). It is then encapsulated behind a MAC header corresponding to the unidirectional link. This packet cannot be sent directly over the link, so it is then processed by the tunneling mechanism. The packet is encapsulated behind an IP header whose destination is the IP address of a feed bidirectional interface (f1b or f2b). This destination address is also called the tunnel end-point. The mechanism for a receiver to learn these addresses and to choose the feed is explained in Section 7. The type of encapsulation is Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 7] Internet Draft LL tunneling mechanism for UDLs Feb 2000 described in Section 8. In all cases the packet is encapsulated, but the tunnel end-point (an IP address) depends on the encapsulated packet's destination MAC address. If the destination MAC address is: 1) the MAC address of a feed interface connected to the unidirectional link (Scenario 1). The datagram is encapsulated, the destination address of the encapsulating datagram is the feed tunnel end-point (f1b referring to Figure 2). 2) a MAC broadcast/multicast address (Scenario 2). The datagram is encapsulated, the destination address of the encapsulating datagram is the default feed tunnel end-point. See Section 7.4 for further details on the default feed. 3) a MAC address that belongs to the unidirectional network but is not a feed address (Scenario 3). The datagram is encapsulated, the destination address of the encapsulating datagram is the default feed tunnel end-point. The encapsulated datagram is passed to the network layer which forwards it according to its destination address. The destination address is a feed bidirectional interface which is reachable via the Internet. In this case, the encapsulated datagram is forwarded via the receiver bidirectional interface (r1b). 6.2. Tunneling mechanism on the feed A feed processes unidirectional link related packets in two different ways: - packets generated by a local application or packets routed as usual by the IP layer may have to be forwarded over the unidirectional link (Section 6.2.1) - encapsulated packets received from another receiver or feed need tunnel processing (Section 6.2.2). A feed cannot directly send a packet to a send-only feed over the unidirectional link (Scenario 4). In order to emulate this type of communication, feeds have to tunnel packets to send-only feeds. A feed MUST maintain a list of all other feed tunnel end-points. This list MUST indicate which are send-only feed tunnel end-points. This is configured manually at the feed by the local administrator, as described in Section 7. 6.2.1. Forwarding packets over the unidirectional link When a datagram is delivered to the link layer of the unidirectional Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 8] Internet Draft LL tunneling mechanism for UDLs Feb 2000 interface of a feed for transmission, its treatment depends on the packet's destination MAC address. If the destination MAC address is: 1) the MAC address of a receiver or a receive capable feed (Scenario 6). The packet is sent over the unidirectional link. This is classical "forwarding". 2) the MAC address of a send-only feed (Scenario 4). The packet is encapsulated and sent to the send-only feed tunnel end-point. The type of encapsulation is described in Section 8. 3) a broadcast/multicast destination (Scenario 5). The packet is sent over the unidirectional link. Concurrently, a copy of this packet is encapsulated and sent to every feed of the list of send-only feed tunnel end-points. Thus the broadcast/multicast will reach all receivers and all send-only feeds. 6.2.2. Receiving encapsulated packets Feeds listen for incoming encapsulated datagrams on their tunnel end- points. Encapsulated packets will have been received on a bidirectional interface, and traversed their way up the IP stack. They will then enter a decapsulation process (See Figure 2). Decapsulation reveals the original link layer packet. Note that this has not been modified in any way by intermediate routers; in particular, the original MAC header will be intact. Further actions depend on the destination MAC address of the link layer packet, which can be: 1) the MAC address of the feed interface connected to the unidirectional link, i.e. own MAC address (Scenarios 1 and 4). The packet is passed to the link layer of the interface connected to the unidirectional link which can then deliver it up to higher layers. As a result, the datagram is processed as if it was coming from the unidirectional link, and being delivered locally. Scenarios 1 and 4 are now feasible, a receiver or a feed can send a packet to a feed. 2) a receiver address (Scenario 3). The packet is passed to the link layer of the interface connected to the unidirectional link. It is directly sent over the unidirectional link, to the indicated receiver. Note, the packet must not be delivered locally. Scenario 3 is now feasible, a receiver can send a packet to another receiver. 3) a broadcast/multicast address, this corresponds to Scenarios 2 Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 9] Internet Draft LL tunneling mechanism for UDLs Feb 2000 and 5. We have to distinguish two cases, either (i) the encapsulated packet was sent from a receiver or (ii) from a feed (encapsulated broadcast/multicast packet sent to a send-only feed). These cases are distinguished by examining the source address of the encapsulating packet and comparing it with the configured list of feed IP addresses. The action then taken is: i) the feed was designated as a default feed by a receiver to forward the broadcast/multicast packet. The feed is then in charge of sending the multicast packet to all nodes. Delivery to all nodes is accomplished by executing all 3 of the following actions: - The packet is encapsulated and sent to the list of send- only feed tunnel end-points. - Also, the packet is passed to the link layer of the interface which forwards it directly over the unidirectional link (all receivers and receive capable feeds receive it). - Also, the link layer delivers it locally to higher layers. Caution: a receiver which sends an encapsulated broadcast/multicast packet to a default feed will receive its own packet via the unidirectional link. Correct filtering as described in [rfc1112] must be applied. ii) the feed receives the packet and keeps it for local delivery. The packet is passed to the link layer of the interface connected to the unidirectional link which delivers it to higher layers. Scenario 2 is now feasible, a receiver can send a broadcast/multicast packet over the unidirectional link and it will be heard by all nodes. 7. Dynamic Tunnel Configuration Protocol (DTCP) Receivers and feeds have to know the feed tunnel end-points in order to forward encapsulated datagrams (e.g. Scenarios 1 and 4). The number of feeds is expected to be relatively small (Section 3), so at every feed the list of all feeds is configured manually. This list should note which are send-only feeds, and which are receive capable feeds. The administrator sets up tunnels to all send-only feeds. A tunnel end-point is an IP address of a bidirectional link on a send-only feed. For scalability reasons, manual configuration cannot be done at the receivers. Tunnels must be configured and maintained dynamically by Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 10] Internet Draft LL tunneling mechanism for UDLs Feb 2000 receivers, both for scalability, and in order to cope with the following events: 1) New feed detection. When a new feed comes up, every receiver must create a tunnel to enable bidirectional communication with it. 2) Loss of unidirectional link detection. When the unidirectional link is down, receivers must disable their tunnels. The tunneling mechanism emulates bidirectional connectivity between nodes. Therefore, if the unidirectional link is down, a feed should not receive datagrams from the receivers. Protocols that consider a link as operational if they receive datagrams from it (e.g. the RIP protocol [rfc2453]) require this behavior for correct operation. 3) Loss of feed detection. When a feed is down, receivers must disable their corresponding tunnel. This prevents unnecessary datagrams from being tunneled which might overload the Internet. For instance, there is no need for receivers to forward a broadcast message through a tunnel whose end-point is down. The DTCP protocol provides a means for receivers to dynamically discover the presence of feeds and to maintain a list of operational tunnel end-points. Feeds periodically announce their tunnel end-point addresses over the unidirectional link. Receivers listen to these announcements and maintain a list of tunnel end-points. 7.1. The HELLO message The DTCP protocol is a 'unidirectional protocol', messages are only sent from feeds to receivers. The packet format is shown in Figure 3. Fields contain binary integers, in normal Internet order with the most significant bit first. Each tick mark represents one bit. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 11] Internet Draft LL tunneling mechanism for UDLs Feb 2000 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Vers | Com | Interval | Sequence | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | res |F|IP Vers| Tunnel Type | Nb of FBIP | reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Feed BDL IP addr (FBIP1) (32/128 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ..... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Feed BDL IP addr (FBIPn) (32/128 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3: Packet Format Every datagram contains the following fields, note that constants are written in uppercase and are defined in Section 7.5: Vers (4 bit unsigned integer): DTCP version number. MUST be DTCP_VERSION. Com (4 bit unsigned integer): Command field, possible values are 1 - JOIN A message announcing that the feed sending this message is up and running. 2 - LEAVE A message announcing that the feed sending this message is being shut down. Interval (8 bit unsigned integer): Interval in seconds between HELLO messages for the IP protocol in "IP Vers". Must be > 0. The recommended value is HELLO_INTERVAL. If this value is increased, the feed MUST continue to send HELLO messages at the old rate for at least the old HELLO_LEAVE period. Sequence (16 bit unsigned integer): Random value initialized at boot time and incremented by 1 every time a value of the HELLO message is modified. res (3 bits): Reserved/unused field, MUST be zero. F (1 bit): bit indicating the type of feed: 0 = Send-only feed 1 = Receive-capable feed IP Vers (4 bit unsigned integer): IP protocol version of the feed bidirectional IP addresses (FBIP): 4 = IP version 4 6 = IP version 6 Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 12] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Tunnel Type (8 bit unsigned integer): tunneling protocol supported by the feed; receivers MUST use this form of tunnel encapsulation when tunneling to the feed. 47 = GRE [rfcXXXX] (recommended) Other values may be used, but their interpretation is not specified here. Nb of FBIP (8 bit unsigned integer): Number of bidirectional IP feed addresses which are enumerated in the HELLO message reserved (8 bits): Reserved/unused field, MUST be zero. Feed BDL IP addr (32 or 128 bits). The bidirectional IP address feed is the IP address of a feed bidirectional interface (tunnel end- point) reachable via the Internet. A feed has 'Nb of FBIP' IP addresses which are operational tunnel end-points. They are enumerated in preferred order. FBIP1 being the most suitable tunnel end-point. 7.2. DTCP on the feed: sending HELLO packets The DTCP protocol runs on top of UDP. Packets are sent to the "DTCP announcement" multicast address over the unidirectional link on port HELLO_PORT with a TTL of 1. The source address of the HELLO packet is set to the IP address of the feed interface connected to the unidirectional link. In the rest of the document, this value is called FUIP (Feed Unidirectional IP address). The process in charge of sending HELLO packets fills every field of the datagram according to the description given in Section 7.1. As long as a feed is up and running, it periodically announces its presence to receivers. It MUST send HELLO packets containing a JOIN command every HELLO_INTERVAL over the unidirectional link. Referring to Figure 1 in Section 3, Feed 1 (resp. Feed 2) sends HELLO messages with the FBIP1 field set to f1b (resp. f2b). When a feed is about to be shut down, or when routing over the unidirectional link is about to be intentionally interrupted, it is recommended that feeds: 1) stop sending HELLO messages containing a JOIN command. 2) send a HELLO message containing a LEAVE command to inform receivers that the feed is no longer performing routing over the Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 13] Internet Draft LL tunneling mechanism for UDLs Feb 2000 unidirectional link. 7.3. DTCP on the receiver: receiving HELLO packets Based on the reception of HELLO messages, receivers discover the presence of feeds, maintain a list of active feeds, and keep track of the tunnel end-points for those feeds. For each active feed, and each IP protocol supported, at least the following information will be kept: FUIP - feed unidirectional link IP address FUMAC - MAC address corresponding to the above IP address (FBIP1,...,FBIPn) - list of tunnel end-points tunnel type - tunnel type supported by this feed Sequence - "Sequence" value from the last HELLO received from this feed timer - used to timeout this entry The FUMAC value for an active feed is needed for the operation of this protocol. However, the method of discovery of this value is not specified here. Initially, the list of active feeds is empty. When a receiver is started, it MUST run a process which joins the "DTCP announcement" multicast group and listens to incoming packets on the HELLO_PORT port from the unidirectional link. Upon the reception of a HELLO message, the process checks the version number of the protocol. If it is different from HELLO_VERSION, the packet is discarded and the process waits for the next incoming packet. After successfully checking the version number further action depends on the type of command: - JOIN: The process verifies if the address FUIP already belongs to the list of active feeds. If it does not, a new entry, for feed FUIP, is created and added to the list of active feeds. The number of feed bidirectional IP addresses to read is deduced from the 'Nb of FBID' field. These tunnel end-points (FBIP1,...,FBIPn) can then be added to the new entry. The tunnel type and Seq values are also taken from the HELLO packet and recorded in the new entry. A timer set to Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 14] Internet Draft LL tunneling mechanism for UDLs Feb 2000 HELLO_LEAVE is associated with this entry. If it does, the sequence number is compared to the sequence number contained in the previous HELLO packet sent by this feed. If they are equal, the timer associated with this entry is reset to HELLO_LEAVE. Otherwise all the information corresponding to FUIP is set to the values from the HELLO packet. Referring to Figure 1 in Section 3, both receivers (recv 1 and recv 2) have a list of active feeds containing two entries: Feed 1 with a FUIP of f1u and a list of tunnel end-points (f1b); and Feed 2 with a FUIP of f2u and a list of tunnel end-points (f2b). - LEAVE: The process checks if there is an entry for FUIP in the list of active feeds. If there is, the timer is disabled and the entry is deleted from the list. The LEAVE message provides a means of quickly updating the list of active feeds. A timeout occurs for either of two reasons: 1) a feed went down without sending a LEAVE message. As JOIN messages are no longer sent from this feed, a timeout occurs at HELLO_LEAVE after the last JOIN message. 2) the unidirectional link is down. Thus no more JOIN messages are received from any of the feeds, and they will each timeout independently. The timeout of each entry depends on its individual HELLO_LEAVE value, and when the last JOIN message was sent by that feed, before the unidirectional link went down. In either case, bidirectional connectivity can no longer be ensured between the receiver and the feed (FUIP): either the feed is no longer routing datagrams over the unidirectional link, or the link is down. Thus the associated entry is removed from the list of active feeds, whatever the cause. As a result, the list only contains operational tunnel end-points. The HELLO protocol provides receivers with a list of feeds, and a list of usable tunnel end-points (FBIP1,..., FBIPn) for each feed. In the following Section, we describe how to integrate the HELLO protocol into the tunneling mechanism described in Sections 6.1 and 6.2. 7.4. Tunneling mechanism using the list of active feeds This Section explains how the tunneling mechanism uses the list of Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 15] Internet Draft LL tunneling mechanism for UDLs Feb 2000 active feeds to handle datagrams which are to be tunneled. Referring to Section 6.1, it shows how feed tunnel end-points are selected. The choice of the default feed is made independently at each receiver. The choice is a matter of local policy, and this policy is out of scope for this document. However, as an example, the default feed may be the feed that has the lowest round trip time to the receiver. When a receiver sends a packet to a feed, it must choose a tunnel end-point from within the FBIP list. The 'preferred FBIP' is generally FBIP1 (Section 7.1). For various reasons, a receiver may decide to use a different FBIP, say FBIPi instead of FBIP1, as the tunnel end-point. For example, the receiver may have better connectivity to FBIPi. This decision is taken by the receiver administrator. Here we show how the list of active feeds is involved when a receiver tunnels a link layer packet. Section 6.1 listed the following cases, depending on whether the MAC destination address of the packet is: 1) the MAC address of a feed interface connected to the unidirectional link: This is TRUE if the address matches a FUMAC address in the list of active feeds. The packet is tunneled to the preferred FBIP of the matching feed. 2) the broadcast address of the unidirectional link or a multicast address: This is determined by the MAC address format rules, and the list of active feeds is not involved. The packet is tunneled to the preferred FBIP of the default feed. 3) an address that belongs to the unidirectional network but is not a feed address: This is TRUE if the address is neither broadcast nor multicast, nor found in the list of active feeds. The packet is tunneled to the preferred FBIP of the default feed. In all cases, the encapsulation type depends on the tunnel type required by the feed which is selected. 7.5. Constant definitions DTCP_VERSION is 1. HELLO_INTERVAL is 5 seconds. "DTCP announcement" multicast group is 224.0.1.124. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 16] Internet Draft LL tunneling mechanism for UDLs Feb 2000 HELLO_PORT is 652. It is a reserved system port, no other traffic must be allowed. HELLO_LEAVE is 3*Interval, as advertised in a HELLO packet, i.e. 15 seconds if the default HELLO_INTERVAL was advertised. 8. Tunnel encapsulation format The tunneling mechanism operates at the link layer and emulates bidirectional connectivity amongst receivers and feeds. We assume that hardware connected to the unidirectional link supports broadcast and unicast MAC addressing. That is, a feed can send a packet to a particular receiver using a unicast MAC destination address or to a set of receivers using a broadcast/multicast destination address. The hardware (or the driver) of the receiver can then filter the incoming packets sent over the unidirectional links without any assumption about the encapsulated data type. In a similar way, a receiver should be capable of sending unicast and broadcast MAC packets via its tunnels. Link layer packets are encapsulated. As a result, after decapsulating an incoming packet, the feed can perform link layer filtering as if the data came directly from the unidirectional link (See Figure 2). Generic Routing Encapsulation (GRE) [rfcXXXX] suits our requirements because it specifies a protocol for encapsulating arbitrary packets, and allows use of IP as the delivery protocol. Other encapsulations are possible, such as directly encapsulating a MAC level packet within an IP datagram. The feed's local administrator decides what encapsulation it will demand that receivers use, and sets the tunnel type field in the HELLO message appropriately. The value 47 (decimal) indicates GRE. Other values can be used, but their interpretation must be agreed upon between feeds and receivers. Such usage is not defined here. 8.1. Generic Routing Encapsulation on the receiver A GRE packet is composed of a header in which a type field specifies the encapsulated protocol (ARP, IP, IPX, etc.). See [rfcXXXX] for details about the encapsulation. In our case, only support for the MAC addressing scheme of the unidirectional link MUST be implemented. A packet tunneled with a GRE encapsulation has the following format: the delivery header is an IP header whose destination is the tunnel end-point (FBIP), followed by a GRE header specifying the link layer Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 17] Internet Draft LL tunneling mechanism for UDLs Feb 2000 type of the unidirectional link. Figure 4 presents the entire encapsulated packet. ---------------------------------------- | IP delivery header | | destination addr = FBIP | | IP proto = GRE (47) | ---------------------------------------- | GRE Header | | type = MAC type of the UDL | ---------------------------------------- | Payload packet | | MAC packet | ---------------------------------------- Figure 4: Encapsulated packet 8.2. Encapsulation of UDL MAC level packets An alternative is to encapsulate the MAC level packet within IP. The protocol field in the IP datagram is then set to the MAC type of the unidirectional link. Figure 5 presents the entire encapsulated packet. ---------------------------------------- | IP delivery header | | destination addr = FBIP | | IP proto = MAC type of the UDL | ---------------------------------------- | Payload packet | | MAC packet | ---------------------------------------- Figure 5: Encapsulated packet 9. Issues 9.1. Hardware address resolution Regardless of whether the link is unidirectional or bidirectional, if a feed sends a packet over a non-point-to-point type network, it requires the data link address of the destination. ARP [rfc826] is used on Ethernet networks for this purpose. The link layer mechanism emulates a bidirectional network in the presence of an unidirectional link. However, there are asymmetric delays between every (feed, receiver) pair. The backchannel between a Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 18] Internet Draft LL tunneling mechanism for UDLs Feb 2000 receiver and a feed has varying delays because packets go through the Internet. Furthermore, a typical example of a unidirectional link is a GEO satellite link whose delay is about 250 milliseconds. Because of long round trip delays, reactive address resolution methods such as ARP [rfc826] may not work well. For example, a feed may have to forward packets at high data rates to a receiver whose hardware address is unknown. The stream of packets is passed to the link layer driver of the feed send-only interface. When the first packet arrives, the link layer realizes it does not have the corresponding hardware address of the next hop, and sends an ARP request. While the link layer is waiting for the response (at least 250 ms for the GEO satellite case), IP packets are buffered by the feed. If it runs out of space before the ARP response arrives, IP packets will be dropped. This problem of address resolution protocols is not addressed in this document. An ad-hoc solution is possible when the MAC address is configurable, which is possible in some satellite receiver cards. A simple transformation (maybe null) of the IP address can then be used as the MAC address. In this case, senders do not need to "resolve" an IP address to a MAC address, they just need to perform the simple transformation. 9.2. Routing protocols The link layer tunneling mechanism hides from the network and higher layers the fact that feeds and receivers are connected by a unidirectional link. Communication is bidirectional, but asymmetric in bandwidths and delays. In order to incorporate unidirectional links in the Internet, feeds and receivers must run routing protocols. These protocols will work fine because the tunneling mechanism results in bidirectional connectivity between all feeds and receivers. Thus routing messages can be exchanged as on any bidirectional network. The tunneling mechanism allows any IP traffic, not just routing protocol messages, to be forwarded between receivers and feeds. Receivers can route datagrams on the Internet using the most suitable feed or receiver as a next hop. Administrators may want to set the metrics used by their routing protocols in order to reflect in routing tables the asymmetric characteristics of the link, and thus direct traffic over appropriate paths. Feeds and receivers can run multicast routing daemons and therefore dynamic multicast routing can be performed over the unidirectional link. However issues related to multicast routing (e.g. protocol Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 19] Internet Draft LL tunneling mechanism for UDLs Feb 2000 configuration) are not addressed in this document. 9.3. Scalability The DTCP protocol does not generate a lot of traffic whatever the number of nodes. The problem with a large number of nodes is not related to this protocol but to more general issues such as the maximum number of nodes which can be connected to any link. This is out of scope of this document. 10. Security Considerations Confidentiality and integrity concerns may arise from the lower layer technologies employed, e.g. if the unidirectional link is a satellite link and the backchannel is the public internet. Since this protocol aims to support a link layer, link layer confidentiality and integrity mechanisms may be appropriate. In the case of the backchannel only, IPSEC [rfc2401] may provide appropriate services. Theft of service and denial of service attacks become possible to systems which can discover the feed tunnel end-point addresses and can direct packets to them. It may be appropriate for feeds to authenticate tunnel sources, i.e. receivers. Feeds can validate the IP source addresses of tunneled packets, but this can be easily spoofed. MAC layer filtering may also be possible. Adequate protection can be ensured using IPSEC [rfc2401] AH [rfc2402] to provide strong authentication of tunnel sources. For reasons of scalability, no particular mechanism is specified in this protocol. 11. Acknowledgments We would like to thank Tim Gleeson (Cisco Japan) for his valuable editing and technical input during the finalization phase of the document. We would like to thank Patrick Cipiere (INRIA) for his valuable input concerning the design of the encapsulation mechanism. We would like also to thank for their participation: Akihiro Tosaka (IMD), Akira Kato (Tokyo Univ.), Hitoshi Asaeda (IBM/ITS), Hiromi Komatsu (JSAT), Hiroyuki Kusumoto (Keio Univ.), Kazuhiro Hara (Sony), Kenji Fujisawa (Sony), Mikiyo Nishida (Keio Univ.), Noritoshi Demizu (Sony csl), Jun Murai (Keio Univ.), Jun Takei (JSAT) and Harri Hakulinen (Nokia). Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 20] Internet Draft LL tunneling mechanism for UDLs Feb 2000 A. Conformance and interoperability This document describes a mechanism to emulate bidirectional connectivity between nodes that are directly connected by a unidirectional link. Applicability over a variety of equipment and environments is ensured by allowing a choice of several key system parameters. Thus in order to ensure interoperability of equipment it is not enough to simply claim conformance with the mechanism defined here. A usage profile for a particular environment will require the definition of several parameters: - the MAC format used - the tunneling mechanism to be used (GRE is recommended) - the "tunnel type" indication if GRE is not used For example, a system might claim to implement "the link layer tunneling mechanism for unidirectional links, using IEEE 802 LLC, and GRE encapsulation for the tunnels." References [rfc826] 'An Ethernet Address Resolution Protocol', David C. Plummer, November 1982. [rfc1112] 'Host Extensions for IP Multicasting', S. Deering, Stanford University, August 1989 [rfc2401] 'Security Architecture for the Internet Protocol', S. Kent, BBN Corp, R. Atkinson, @Home Network [rfc2402] 'IP Authentication Header', S. Kent, BBN Corp, R. Atkinson, @Home Network [rfc2453] 'RIP Version 2', G. Malkin, Bay Networks, November 1998 [rfcXXXX] 'Generic Routing Encapsulation (GRE)', D. Farinacci, T. Li, S. Hanks, D. Meyer, P. Traina. Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 21] Internet Draft LL tunneling mechanism for UDLs Feb 2000 Author's address Emmanuel Duros INRIA Sophia Antipolis 2004, Route des Lucioles BP 93 06902 Sophia Antipolis France Phone : +33 4 92 38 79 42 Fax : +33 4 92 38 79 78 Email : Emmanuel.Duros@inria.fr Walid Dabbous INRIA Sophia Antipolis 2004, Route des Lucioles BP 93 06902 Sophia Antipolis France Phone : +33 4 92 38 77 18 Fax : +33 4 92 38 79 78 Email : Walid.Dabbous@inria.fr Hidetaka Izumiyama Japan Satellite Systems Inc. Toranomon 17 Mori Bldg.5F 1-26-5 Toranomon, Minato-ku Tokyo 105 Japan Voice : +81-3-5511-7568 Fax : +81-3-5512-7181 Email : izu@jcsat.co.jp Noboru Fujii Sony Corporation 2-10-14 Osaki, Shinagawa-ku Tokyo 141 Japan Voice : +81-3-3495-3092 Fax : +81-3-3495-3527 Email : fujii@dct.sony.co.jp Yongguang Zhang HRL RL-96, 3011 Malibu Canyon Road Malibu, CA 90265, USA Phone : 310-317-5147 Fax : 310-317-5695 Email : ygz@hrl.com Duros, Dabbous, Izumiyama, Fujii, Zhang [Page 22]