TEAS Working Group T. Saad, Ed. Internet-Draft R. Gandhi Intended status: Standards Track Cisco Systems Inc Expires: September 21, 2016 X. Liu Ericsson V. Beeram Juniper Networks H. Shah Ciena X. Chen Huawei Technologies R. Jones Brocade B. Wen Comcast March 20, 2016 A YANG Data Model for Traffic Engineering Tunnels and Interfaces draft-ietf-teas-yang-te-03 Abstract This document defines a YANG data model for the configuration and management of Traffic Engineering (TE) interfaces, tunnels and Label Switched Paths (LSPs). The model is divided into YANG modules that classify data into generic, device-specific, technology agnostic, and technology-specific elements. The model also includes module(s) that contain reusable TE data types and data groupings. This model covers the configuration, operational state, remote procedural calls, and event notifications data. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." Saad, et al. Expires September 21, 2016 [Page 1] Internet-Draft TE YANG Data Model March 2016 This Internet-Draft will expire on September 21, 2016. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 1.2. Tree Diagram . . . . . . . . . . . . . . . . . . . . . . 3 1.3. Prefixes in Data Node Names . . . . . . . . . . . . . . . 4 1.4. Open Issues and Next Steps . . . . . . . . . . . . . . . 5 1.4.1. TE Technology Models . . . . . . . . . . . . . . . . 5 1.4.2. State Data Organization . . . . . . . . . . . . . . . 5 2. Model Overview . . . . . . . . . . . . . . . . . . . . . . . 6 2.1. Module(s) Relationship . . . . . . . . . . . . . . . . . 6 2.2. Design Considerations . . . . . . . . . . . . . . . . . . 8 2.3. Optional Features . . . . . . . . . . . . . . . . . . . . 9 2.4. Configuration Inheritance . . . . . . . . . . . . . . . . 9 2.5. Routing Instance Support . . . . . . . . . . . . . . . . 9 3. TE Generic Model Organization . . . . . . . . . . . . . . . . 9 3.1. Global Configuration and State Data . . . . . . . . . . . 11 3.2. Interfaces Configuration and State Data . . . . . . . . . 14 3.3. Tunnels Configuration and State Data . . . . . . . . . . 18 3.4. TE LSPs State Data . . . . . . . . . . . . . . . . . . . 27 3.5. Global RPC Data . . . . . . . . . . . . . . . . . . . . . 29 3.6. Interface RPC Data . . . . . . . . . . . . . . . . . . . 29 3.7. Tunnel RPC Data . . . . . . . . . . . . . . . . . . . . . 29 3.8. Global Notifications Data . . . . . . . . . . . . . . . . 29 3.9. Interfaces Notifications Data . . . . . . . . . . . . . . 29 3.10. Tunnel Notification Data . . . . . . . . . . . . . . . . 30 4. TE Generic and Helper YANG Modules . . . . . . . . . . . . . 30 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 88 6. Security Considerations . . . . . . . . . . . . . . . . . . . 88 7. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 89 8. References . . . . . . . . . . . . . . . . . . . . . . . . . 89 Saad, et al. Expires September 21, 2016 [Page 2] Internet-Draft TE YANG Data Model March 2016 8.1. Normative References . . . . . . . . . . . . . . . . . . 89 8.2. Informative References . . . . . . . . . . . . . . . . . 91 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 91 1. Introduction YANG [RFC6020] is a data definition language that was introduced to define the contents of a conceptual data store that allows networked devices to be managed using NETCONF [RFC6241]. YANG is proving relevant beyond its initial confines, as bindings to other interfaces (e.g. ReST) and encoding other than XML (e.g. JSON) are being defined. Furthermore, YANG data models can be used as the basis of implementation for other interface, such as CLI and programmatic APIs. This document covers the YANG data model for the TE generic, TE device-specific, TE MPLS technology and helper modules. It also describes the high-level relationship between these modules and to other external protocol modules. It is expected that other data plane technology model(s) will augment the TE generic model. Also, the generic model does not include any signaling protocol specific data, and it is expected other TE signaling protocol modules (e.g. RSVP-TE ([RFC3209], [RFC3473]), and Segment-Routing TE (SR-TE)) will augment the TE generic model. 1.1. Terminology In this document, the key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" are to be interpreted as described in BCP 14, RFC 2119 [RFC2119]. 1.2. Tree Diagram A simplified graphical representation of the data model is presented in each section of the model. The following notations are used for the YANG model data tree representation. Saad, et al. Expires September 21, 2016 [Page 3] Internet-Draft TE YANG Data Model March 2016 is one of: + for current x for deprecated o for obsolete is one of: rw for read-write configuration data ro for read-only non-configuration data -x for execution rpcs -n for notifications is the name of the node If the node is augmented into the tree from another module, its name is printed as : is one of: ? for an optional leaf or node ! for a presence container * for a leaf-list or list Brackets [] for a list's keys Curly braces {} for optional feature that make node conditional Colon : for marking case nodes Ellipses ("...") subtree contents not shown Parentheses enclose choice and case nodes, and case nodes are also marked with a colon (":"). is the name of the type for leafs and leaf-lists. 1.3. Prefixes in Data Node Names In this document, names of data nodes and other data model objects are prefixed using the standard prefix associated with the corresponding YANG imported modules, as shown in Table 1. +--------+-----------------+-----------+ | Prefix | YANG module | Reference | +--------+-----------------+-----------+ | yang | ietf-yang-types | [RFC6991] | | inet | ietf-inet-types | [RFC6991] | +--------+-----------------+-----------+ Table 1: Prefixes and corresponding YANG modules Saad, et al. Expires September 21, 2016 [Page 4] Internet-Draft TE YANG Data Model March 2016 1.4. Open Issues and Next Steps This section describes the number of open issues that are under consideration. As issues are resolved, this section will be updated to reflect this and be left there for reference. It is expected that all the issues in this section will be addressed before the document will be ready for final publication. 1.4.1. TE Technology Models This document describes the generic TE YANG data model that is independent of any dataplane technology. It is expected that specific data plane technologies will reuse this YANG model by attaching it at technology specific targets and by possibly augmenting TE generic model with technology specific data. There are currently multiple proposals under consideration at IETF to allow attaching or "mounting" a YANG model at multiple targets- for example, [I-D.clemm-netmod-mount], and [I-D.bjorklund-netmod-structural-mount]. This model will adhere to the final adopted approach at IETF when it is reached. Also, the TE generic model does not include any signaling protocol data, and it is expected other TE signaling protocol modules (e.g. RSVP-TE ([RFC3209], [RFC3473]), and Segment-Routing TE (SR-TE)) will augment the TE generic model. 1.4.2. State Data Organization Pure state data (for example, ephemeral or protocol derived state objects) can be modeled using one of the options below: o Contained inside a read-write container, in a "state" sub- container, as shown in Figure 3 o Contained inside a separate read-only container, for example a lsps-state container The first option allows for placing configuration data in the read- write "config" sub-container, and by placing state data under the read-only "state" sub-container of the parent container. However, when using approach for ephemeral or purely derived state (e.g. auto tunnels), and since in this case the state sub-container hangs off a read-write parent container, it will be possible to delete or modify the parent container and subsequently the ephemeral read-only state contained within (see Figure 3). Saad, et al. Expires September 21, 2016 [Page 5] Internet-Draft TE YANG Data Model March 2016 The second option entails defining a new read-only parent container in the model (e.g. neighbors-state) that holds the data. This revision of the draft adopts the first option for ephemeral or state derived tunnels. Further discussions on this topic are expected to close on the best choice to adopt. 2. Model Overview The data model defined in this document covers the core TE features that are commonly supported across different vendor implementations. The support of extended or vendor specific TE feature(s) are expected to be in augmentations to the data models defined in this document. Throughout the model, the approach described in [I-D.openconfig-netmod-opstate] is adopted to represent data pertaining to configuration intended state, applied state and derived state data elements. Each container in the model hold a "config" and "state" sub-container. The "config" sub-container is used to represent the intended configurable parameters, and the state sub- container is used to represent both the applied configurable parameters and any derived state, such as counters or statistics information. The decision to use this approach was made to better align with the MPLS consolidated model in [I-D.openconfig-mpls-consolidated-model] and maximize reusability of groupings defined in this document and allow for possible convergence between the two models. 2.1. Module(s) Relationship The TE generic model defined in "ietf-te.yang" covers the building blocks that are device independent and agnostic of a specific technology or control plane instantiations. The TE device model defined in "ietf-te-device.yang" augments the TE generic and covers data that is specific to a device - for example, attributes of TE interfaces, or TE timers that are local to a TE node. The TE data relevant to a specific instantiations of data plane technology exists in a separate YANG module(s) that augment the TE generic model. For example, the MPLS-TE module "ietf-te-mpls.yang" is defined in Figure 14 and augments the TE generic model as shown in Figure 1. The TE data relevant to a TE specific signaling protocol instantiation is outside the scope and is covered in other documents. For example, the RSVP-TE [RFC3209] YANG model augmentation of the TE model is covered in [I-D.ietf-teas-yang-rsvp], and other signaling Saad, et al. Expires September 21, 2016 [Page 6] Internet-Draft TE YANG Data Model March 2016 protocol model(s) (e.g. for Segment-Routing TE) are expected to also augment the TE generic model. TE generic +---------+ ^: import module | ietf-te | o: augment +---------+ | o \ | |\ \ | | \ V | | +----------------+ | | | ietf-te-device | TE device module | | +----------------+ | | o | | / v | / +--------------+ RSVP-TE module | ietf-rsvp-te |o . . . +--------------+ \ ^ | \ | o +-------------------+ +-----------+ | ietf-rsvp-otn-te | RSVP module | ietf-rsvp | +-------------------+ +-----------+ RSVP-TE with OTN extensions (shown for illustration not in this document) Figure 1: Relationship of TE module(s) with other signaling protocol modules Saad, et al. Expires September 21, 2016 [Page 7] Internet-Draft TE YANG Data Model March 2016 +---------+ | ietf-te | ^: import +---------+ o: augment import ^ | | +---------------+ | ietf-te-types | +---------------+ o o | \ | \ +-------------------+ +-------------------+ | ietf-te-mpls-types | | ietf-te-otn-types | +-------------------+ +-------------------+ (shown for illustration not in this document) Figure 2: Relationship between generic and technology specific TE types modules 2.2. Design Considerations The following considerations with respect data organization are taken into account: o reusable data elements are grouped into separate TE types module(s) that can be readily imported by other modules whenever needed o reusable TE data types that are data plane independent are grouped in the TE generic types module "ietf-te-types.yang" o reusable TE data elements that are data plane specific (e.g. packet MPLS or switching technologies as defined in [RFC3473]) are expected to be grouped in a technology- specific types module, e.g. "ietf-te-mpls-types.yang". It is expected that technology specific types will augment TE generic types as shown in Figure 2 o The TE generic model contains device independent data and can be used to model data off a device (e.g. on a controller). The TE data that is device-specific are grouped in a separate module as shown in Figure 1. o In general, little information in the model is designated as "mandatory", to allow freedom to vendors to adapt the data model to their specific product implementation. Saad, et al. Expires September 21, 2016 [Page 8] Internet-Draft TE YANG Data Model March 2016 2.3. Optional Features Optional features that are beyond the base TE model and are left to the specific vendor to decide support using vendor model augmentation and/or using feature checks. This model declares a number of TE functions as features (such as P2MP-TE, soft-preemption etc.). 2.4. Configuration Inheritance The defined data model supports configuration inheritance for tunnels, paths, and interfaces. Data elements defined in the main container (e.g. that encompasses the list of tunnels, interfaces, or paths) are assumed to apply equally to all elements of the list, unless overridden explicitly for a certain element of a list (e.g. a tunnel, interface or path). 2.5. Routing Instance Support There two main popular types of routing protocol configuration that vendors may support: o protocol centric - all the protocol related configuration is contained within the protocol itself. Configuration belonging to multiple instances of the protocol running in different routing- instances (e.g. VRFs) are contained under the default routing instance [I-D.ietf-netmod-routing-cfg]: o VRF centric - all the protocol related configuration for a routing- instance is contained within this routing-instance. On-going discussions within the IETF community have converged on adopting the VRF centric approach. The proposed model in this document adheres to this conclusion. 3. TE Generic Model Organization This model covers configuration, state, RPC, and notifications data pertaining to TE global parameters, interfaces, and tunnels parameters. The container "te" is the top level container in this data model. The presence of this container is expected to enable TE function system wide. The approach described in [I-D.openconfig-netmod-opstate] allows for modeling the intended and respective applied and derived state. The Saad, et al. Expires September 21, 2016 [Page 9] Internet-Draft TE YANG Data Model March 2016 TE state data in this model falls into one of the following categories: o State corresponding to applied configuration o State corresponding to derived state, counters, stats, etc. o State corresponding to ephemeral data (e.g. LSPs, etc.) Data for the first two categories are contained under the respective "state" sub-container of the intended (e.g. tunnel). The last category falls under a separate - e.g. lsps-state- container that contains the attributes of a purely derived state data (e.g. ephemeral objects) that are not associated with any configuration as shown in Figure 3. module: ietf-te +--rw te! +--rw globals +-- rw config <> . +-- ro state <> <> . . +--rw tunnels +-- rw config <> . +-- ro state <> <> . . rpcs: +---x globals-rpc +---x tunnels-rpc notifications: +---n globals-notif +---n tunnels-notif Figure 3: TE generic highlevel model view Saad, et al. Expires September 21, 2016 [Page 10] Internet-Draft TE YANG Data Model March 2016 3.1. Global Configuration and State Data This branch of the data model covers configurations that control TE features behavior system-wide, and its respective state. Examples of such configuration data are: o Table of named SRLG mappings o Table of named (extended) administrative groups mappings o Table of named explicit paths to be referenced by TE tunnels o Table of named path-constraints sets o Auto-bandwidth global parameters o TE diff-serve TE-class maps o System-wide capabilities for LSP reoptimization (included in the TE device model) * Reoptimization timers (periodic interval, LSP installation and cleanup) o System-wide capabilities for TE state flooding (included in the TE device model) * Periodic flooding interval o Global capabilities that affect the originating, traversing and terminating LSPs. For example: * Path selection parameters (e.g. metric to optimize, etc.) * Path or segment protection parameters The approach described in [I-D.openconfig-netmod-opstate] is utilized to include the global state data under the global "state" sub- container as shown in Figure 3. Examples of such states are: o Global statistics (signaling, admission, preemption, flooding) o Global counters (number of tunnels/LSPs/interfaces) module: ietf-te +--rw te! Saad, et al. Expires September 21, 2016 [Page 11] Internet-Draft TE YANG Data Model March 2016 +--rw globals | +--rw config | | +--rw named-admin-groups* [name] {te-types:extended-admin-groups,te-types:named-extended-admin-groups}? | | | +--rw name string | | | +--rw bit-position? uint32 | | +--rw named-srlgs* [name] {te-types:named-srlg-groups}? | | | +--rw name string | | | +--rw group? te-types:srlg | | +--rw named-explicit-paths* [name] | | | +--rw name string | | | +--rw explicit-route-objects* [index] | | | +--rw index uint8 | | | +--rw explicit-route-usage? identityref | | | +--rw (type)? | | | +--:(ipv4-address) | | | | +--rw v4-address? inet:ipv4-address | | | | +--rw v4-prefix-length? uint8 | | | | +--rw v4-loose? boolean | | | +--:(ipv6-address) | | | | +--rw v6-address? inet:ipv6-address | | | | +--rw v6-prefix-length? uint8 | | | | +--rw v6-loose? boolean | | | +--:(as-number) | | | | +--rw as-number? uint16 | | | +--:(unnumbered-link) | | | | +--rw router-id? inet:ip-address | | | | +--rw interface-id? uint32 | | | +--:(label) | | | +--rw value? uint32 | | +--rw named-constraints* [name] {te-types:named-path-constraints}? | | | +--rw name string | | | +--rw path-selection | | | +--rw topology? te-types:topology-id | | | +--rw cost-limit? uint32 | | | +--rw hop-limit? uint8 | | | +--rw metric-type? identityref | | | +--rw tiebreaker-type? identityref | | | +--rw ignore-overload? boolean | | | +--rw tunnel-path-affinities {named-path-affinities}? | | | | +--rw (style)? | | | | +--:(values) | | | | | +--rw value? uint32 | | | | | +--rw mask? uint32 | | | | +--:(named) | | | | +--rw constraints* [usage] | | | | +--rw usage identityref Saad, et al. Expires September 21, 2016 [Page 12] Internet-Draft TE YANG Data Model March 2016 | | | | +--rw constraint | | | | +--rw affinity-names* [name] | | | | +--rw name string | | | +--rw tunnel-path-srlgs | | | +--rw (style)? | | | +--:(values) | | | | +--rw usage? identityref | | | | +--rw values* te-types:srlg | | | +--:(named) | | | +--rw constraints* [usage] | | | +--rw usage identityref | | | +--rw constraint | | | +--rw srlg-names* [name] | | | +--rw name string | | +--rw te-dev:lsp-install-interval? uint32 | | +--rw te-dev:lsp-cleanup-interval? uint32 | +--ro state | +--ro named-admin-groups* [name] {te-types:extended-admin-groups,te-types:named-extended-admin-groups}? | | +--ro name string | | +--ro bit-position? uint32 | +--ro named-srlgs* [name] {te-types:named-srlg-groups}? | | +--ro name string | | +--ro group? te-types:srlg | +--ro named-explicit-paths* [name] | | +--ro name string | | +--ro explicit-route-objects* [index] | | +--ro index uint8 | | +--ro explicit-route-usage? identityref | | +--ro (type)? | | +--:(ipv4-address) | | | +--ro v4-address? inet:ipv4-address | | | +--ro v4-prefix-length? uint8 | | | +--ro v4-loose? boolean | | +--:(ipv6-address) | | | +--ro v6-address? inet:ipv6-address | | | +--ro v6-prefix-length? uint8 | | | +--ro v6-loose? boolean | | +--:(as-number) | | | +--ro as-number? uint16 | | +--:(unnumbered-link) | | | +--ro router-id? inet:ip-address | | | +--ro interface-id? uint32 | | +--:(label) | | +--ro value? uint32 | +--ro named-constraints* [name] {te-types:named-path-constraints}? | | +--ro name string Saad, et al. Expires September 21, 2016 [Page 13] Internet-Draft TE YANG Data Model March 2016 | | +--ro path-selection | | +--ro topology? te-types:topology-id | | +--ro cost-limit? uint32 | | +--ro hop-limit? uint8 | | +--ro metric-type? identityref | | +--ro tiebreaker-type? identityref | | +--ro ignore-overload? boolean | | +--ro tunnel-path-affinities {named-path-affinities}? | | | +--ro (style)? | | | +--:(values) | | | | +--ro value? uint32 | | | | +--ro mask? uint32 | | | +--:(named) | | | +--ro constraints* [usage] | | | +--ro usage identityref | | | +--ro constraint | | | +--ro affinity-names* [name] | | | +--ro name string | | +--ro tunnel-path-srlgs | | +--ro (style)? | | +--:(values) | | | +--ro usage? identityref | | | +--ro values* te-types:srlg | | +--:(named) | | +--ro constraints* [usage] | | +--ro usage identityref | | +--ro constraint | | +--ro srlg-names* [name] | | +--ro name string | +--ro te-dev:lsp-install-interval? uint32 | +--ro te-dev:lsp-cleanup-interval? uint32 | +--ro te-dev:tunnels-counter? uint32 | +--ro te-dev:lsps-counter? uint32 Figure 4: TE globals configuration and state tree 3.2. Interfaces Configuration and State Data This branch of the model covers configuration and state data items, corresponding to TE interfaces that are present on a specific device. A new module is introduced that holds the TE device specific properties. Examples of TE interface properties are: o Maximum reservable bandwidth, bandwidth constraints (BC) o Flooding parameters Saad, et al. Expires September 21, 2016 [Page 14] Internet-Draft TE YANG Data Model March 2016 * Flooding intervals and threshold values o Fast reroute backup tunnel properties (such as static, auto- tunnel) o interface attributes * (Extended) administrative groups * SRLG values * TE metric value module: ietf-te-device +--rw te! +--rw te-dev:interfaces +--rw te-dev:config | +--rw te-dev:thresholds | +--rw (type)? | +--:(equal-steps) | | +--rw (equal-step-type)? | | +--:(up-down-different-step) | | | +--rw te-dev:up-step? uint8 | | | +--rw te-dev:down-step? uint8 | | +--:(up-down-same-step) | | +--rw te-dev:step? uint8 | +--:(unequal-steps) | +--rw te-dev:up-steps* [value] | | +--rw te-dev:value uint8 | +--rw te-dev:down-steps* [value] | +--rw te-dev:value uint8 +--ro te-dev:state | +--ro te-dev:thresholds | +--ro (type)? | +--:(equal-steps) | | +--ro (equal-step-type)? | | +--:(up-down-different-step) | | | +--ro te-dev:up-step? uint8 | | | +--ro te-dev:down-step? uint8 | | +--:(up-down-same-step) | | +--ro te-dev:step? uint8 | +--:(unequal-steps) | +--ro te-dev:up-steps* [value] | | +--ro te-dev:value uint8 | +--ro te-dev:down-steps* [value] | +--ro te-dev:value uint8 +--rw te-dev:interface* [interface] +--rw te-dev:interface if:interface-ref Saad, et al. Expires September 21, 2016 [Page 15] Internet-Draft TE YANG Data Model March 2016 +--rw te-dev:config | +--rw te-dev:te-metric? te-types:te-metric | +--rw (admin-group-type)? | | +--:(value-admin-groups) | | | +--rw (value-admin-group-type)? | | | +--:(admin-groups) | | | | +--rw te-dev:admin-group?te-types:admin-group | | | +--:(extended-admin-groups) | | | +--rw te-dev:extended-admin-group? | | +--:(named-admin-groups) | | +--rw te-dev:named-admin-groups*[named-admin-group] | | +--rw te-dev:named-admin-group -> ../../../../../ietf-te:globals/config/named-admin-groups/name | +--rw (srlg-type)? | | +--:(value-srlgs) | | | +--rw te-dev:values* [value] | | | +--rw te-dev:value uint32 | | +--:(named-srlgs) | | +--rw te-dev:named-srlgs* [named-srlg] | | +--rw te-dev:named-srlg -> ../../../../../ietf-te:globals/config/named-srlgs/name | +--rw te-dev:switching-capabilities*[switching-cap] | | +--rw te-dev:switching-capability identityref | | +--rw te-dev:encoding? identityref | +--rw te-dev:thresholds | +--rw (type)? | +--:(equal-steps) | | +--rw (equal-step-type)? | | +--:(up-down-different-step) | | | +--rw te-dev:up-step? uint8 | | | +--rw te-dev:down-step? uint8 | | +--:(up-down-same-step) | | +--rw te-dev:step? uint8 | +--:(unequal-steps) | +--rw te-dev:up-steps* [value] | | +--rw te-dev:value uint8 | +--rw te-dev:down-steps* [value] | +--rw te-dev:value uint8 +--ro te-dev:state +--ro te-dev:te-metric? te-types:te-metric +--ro (admin-group-type)? | +--:(value-admin-groups) | | +--ro (value-admin-group-type)? | | +--:(admin-groups) | | | +--ro te-dev:admin-group? | | +--:(extended-admin-groups) | | +--ro te-dev:extended-admin-group? | +--:(named-admin-groups) Saad, et al. Expires September 21, 2016 [Page 16] Internet-Draft TE YANG Data Model March 2016 | +--ro te-dev:named-admin-groups*[named-admin-group] | +--ro te-dev:named-admin-group -> ../../../../../ietf-te:globals/config/named-admin-groups/name +--ro (srlg-type)? | +--:(value-srlgs) | | +--ro te-dev:values* [value] | | +--ro te-dev:value uint32 | +--:(named-srlgs) | +--ro te-dev:named-srlgs* [named-srlg] | +--ro te-dev:named-srlg -> ../../../../../ietf-te:globals/config/named-srlgs/name +--ro te-dev:switching-capabilities*[switching-cap] | +--ro te-dev:switching-capability identityref | +--ro te-dev:encoding? identityref +--ro te-dev:thresholds | +--ro (type)? | +--:(equal-steps) | | +--ro (equal-step-type)? | | +--:(up-down-different-step) | | | +--ro te-dev:up-step? uint8 | | | +--ro te-dev:down-step? uint8 | | +--:(up-down-same-step) | | +--ro te-dev:step? uint8 | +--:(unequal-steps) | +--ro te-dev:up-steps* [value] | | +--ro te-dev:value uint8 | +--ro te-dev:down-steps* [value] | +--ro te-dev:value uint8 +--ro te-dev:te-advertisements_state +--ro te-dev:flood-interval? uint32 +--ro te-dev:last-flooded-time? uint32 +--ro te-dev:next-flooded-time? uint32 +--ro te-dev:last-flooded-trigger? enumeration +--ro te-dev:advertized-level-areas* [level-area] +--ro te-dev:level-area uint32 Figure 5: TE interfaces configuration and state tree The state corresponding to the TE interfaces applied configuration, protocol derived state, and stats and counters all fall under the interface "state" sub-container as shown in Figure 6 below: Saad, et al. Expires September 21, 2016 [Page 17] Internet-Draft TE YANG Data Model March 2016 module: ietf-te +--rw te! +--rw interfaces . +-- rw te-attributes +-- rw config <> . +-- ro state <> <> Figure 6: TE interface state This covers state data for TE interfaces such as: o Bandwidth information: maximum bandwidth, available bandwidth at different priorities and for each class-type (CT) o List of admitted LSPs * Name, bandwidth value and pool, time, priority o Statistics: state counters, flooding counters, admission counters (accepted/rejected), preemption counters o Adjacency information * Neighbor address * Metric value 3.3. Tunnels Configuration and State Data This branch of the model covers intended, and corresponding applied configuration for tunnels. As well, it holds possible derived state pertaining to TE tunnels. The approach described in [I-D.openconfig-netmod-opstate] is utilized for the inclusion of operational and statistical data as shown in Figure 7. Saad, et al. Expires September 21, 2016 [Page 18] Internet-Draft TE YANG Data Model March 2016 module: ietf-te +--rw te! +--rw tunnels . +-- rw config <> . +-- ro state <> <> Figure 7: TE interface state tree Examples of tunnel configuration date for TE tunnels: o Name and type (e.g. P2P, P2MP) of the TE tunnel o Admin-state o Set of primary and corresponding secondary paths o Routing usage (auto-route announce, forwarding adjacency) o Policy based routing (PBR) parameters module: ietf-te +--rw te! +--rw tunnels | +--rw tunnel* [name type] | +--rw name -> ../config/name | +--rw type -> ../config/type | +--rw identifier? -> ../config/identifier | +--rw config | | +--rw name? string | | +--rw type? identityref | | +--rw identifier? uint16 | | +--rw description? string | | +--rw lsp-priority-setup? uint8 | | +--rw lsp-priority-hold? uint8 | | +--rw lsp-protection-type? identityref | | +--rw admin-status? identityref | | +--rw source? inet:ip-address | | +--rw destination? inet:ip-address | | +--rw src-tp-id? binary | | +--rw tunnel-dst-tp-id? binary | | +--rw bidirectional | | | +--rw association | | | +--rw id? uint16 Saad, et al. Expires September 21, 2016 [Page 19] Internet-Draft TE YANG Data Model March 2016 | | | +--rw source? inet:ip-address | | | +--rw global-source? inet:ip-address | | | +--rw type? identityref | | | +--rw provisioing? identityref | | +--rw (routing-choice)? | | | +--:(autoroute) | | | | +--rw te-mpls:autoroute-announce! | | | | +--rw te-mpls:routing-afs* inet:ip-version | | | | +--rw (metric-type)? | | | | +--:(metric) | | | | | +--rw te-mpls:metric? uint32 | | | | +--:(relative-metric) | | | | | +--rw te-mpls:relative-metric? int32 | | | | +--:(absolute-metric) | | | | +--rw te-mpls:absolute-metric? uint32 | | | +--:(forwarding-adjacency) | | | +--rw te-mpls:forwarding-adjacency! | | | +--rw te-mpls:holdtime? uint32 | | | +--rw te-mpls:routing-afs* inet:ip-version | | +--rw te-mpls:forwarding | | +--rw te-mpls:load-share? uint32 | | +--rw (policy-type)? | | +--:(class) | | | +--rw te-mpls:class | | | +--rw te-mpls:class? uint8 | | +--:(group) | | +--rw te-mpls:group | | +--rw te-mpls:classes* uint8 | +--ro state | | +--ro name? string | | +--ro type? identityref | | +--ro identifier? uint16 | | +--ro description? string | | +--ro lsp-priority-setup? uint8 | | +--ro lsp-priority-hold? uint8 | | +--ro lsp-protection-type? identityref | | +--ro admin-status? identityref | | +--ro source? inet:ip-address | | +--ro destination? inet:ip-address | | +--ro src-tp-id? binary | | +--ro tunnel-dst-tp-id? binary | | +--ro bidirectional | | | +--ro association | | | +--ro id? uint16 | | | +--ro source? inet:ip-address | | | +--ro global-source? inet:ip-address | | | +--ro type? identityref | | | +--ro provisioing? identityref Saad, et al. Expires September 21, 2016 [Page 20] Internet-Draft TE YANG Data Model March 2016 | | +--ro oper-status? identityref | | +--ro (routing-choice)? | | | +--:(autoroute) | | | | +--ro te-mpls:autoroute-announce! | | | | +--ro te-mpls:routing-afs* inet:ip-version | | | | +--ro (metric-type)? | | | | +--:(metric) | | | | | +--ro te-mpls:metric? uint32 | | | | +--:(relative-metric) | | | | | +--ro te-mpls:relative-metric? int32 | | | | +--:(absolute-metric) | | | | +--ro te-mpls:absolute-metric? uint32 | | | +--:(forwarding-adjacency) | | | +--ro te-mpls:forwarding-adjacency! | | | +--ro te-mpls:holdtime? uint32 | | | +--ro te-mpls:routing-afs* inet:ip-version | | +--ro te-mpls:forwarding | | +--ro te-mpls:load-share? uint32 | | +--ro (policy-type)? | | +--:(class) | | | +--ro te-mpls:class | | | +--ro te-mpls:class? uint8 | | +--:(group) | | +--ro te-mpls:group | | +--ro te-mpls:classes* uint8 | +--rw primary-paths* [name] | +--rw name -> ../config/name | +--rw preference? -> ../config/preference | +--rw config | | +--rw name? string | | +--rw preference? uint8 | | +--rw path-named-constraint? string | | +--rw path-selection | | | +--rw topology? te-types:topology-id | | | +--rw cost-limit? uint32 | | | +--rw hop-limit? uint8 | | | +--rw metric-type? identityref | | | +--rw tiebreaker-type? identityref | | | +--rw ignore-overload? boolean | | | +--rw tunnel-path-affinities {named-path-aff}? | | | | +--rw (style)? | | | | +--:(values) | | | | | +--rw value? uint32 | | | | | +--rw mask? uint32 | | | | +--:(named) | | | | +--rw constraints* [usage] | | | | +--rw usage identityref | | | | +--rw constraint Saad, et al. Expires September 21, 2016 [Page 21] Internet-Draft TE YANG Data Model March 2016 | | | | +--rw affinity-names* [name] | | | | +--rw name string | | | +--rw tunnel-path-srlgs | | | +--rw (style)? | | | +--:(values) | | | | +--rw usage? identityref | | | | +--rw values* te-types:srlg | | | +--:(named) | | | +--rw constraints* [usage] | | | +--rw usage identityref | | | +--rw constraint | | | +--rw srlg-names* [name] | | | +--rw name string | | +--rw (type)? | | | +--:(dynamic) | | | | +--rw dynamic? empty | | | +--:(explicit) | | | +--rw explicit-path-name? string | | | +--rw explicit-route-objects* [index] | | | +--rw index uint8 | | | +--rw explicit-route-usage? identityref | | | +--rw (type)? | | | +--:(ipv4-address) | | | | +--rw v4-address? inet:ipv4-address | | | | +--rw v4-prefix-length? uint8 | | | | +--rw v4-loose? boolean | | | +--:(ipv6-address) | | | | +--rw v6-address? inet:ipv6-address | | | | +--rw v6-prefix-length? uint8 | | | | +--rw v6-loose? boolean | | | +--:(as-number) | | | | +--rw as-number? uint16 | | | +--:(unnumbered-link) | | | | +--rw router-id? inet:ip-address | | | | +--rw interface-id? uint32 | | | +--:(label) | | | +--rw value? uint32 | | +--rw no-cspf? empty | | +--rw lockdown? empty | +--ro state | | +--ro path-named-constraint? string | | +--ro path-selection | | | +--ro topology? te-types:topology-id | | | +--ro cost-limit? uint32 | | | +--ro hop-limit? uint8 | | | +--ro metric-type? identityref | | | +--ro tiebreaker-type? identityref | | | +--ro ignore-overload? boolean Saad, et al. Expires September 21, 2016 [Page 22] Internet-Draft TE YANG Data Model March 2016 | | | +--ro tunnel-path-affinities | | | | +--ro (style)? | | | | +--:(values) | | | | | +--ro value? uint32 | | | | | +--ro mask? uint32 | | | | +--:(named) | | | | +--ro constraints* [usage] | | | | +--ro usage identityref | | | | +--ro constraint | | | | +--ro affinity-names* [name] | | | | +--ro name string | | | +--ro tunnel-path-srlgs | | | +--ro (style)? | | | +--:(values) | | | | +--ro usage? identityref | | | | +--ro values* te-types:srlg | | | +--:(named) | | | +--ro constraints* [usage] | | | +--ro usage identityref | | | +--ro constraint | | | +--ro srlg-names* [name] | | | +--ro name string | | +--ro (type)? | | | +--:(dynamic) | | | | +--ro dynamic? empty | | | +--:(explicit) | | | +--ro explicit-path-name? string | | | +--ro explicit-route-objects* [index] | | | +--ro index uint8 | | | +--ro explicit-route-usage? identityref | | | +--ro (type)? | | | +--:(ipv4-address) | | | | +--ro v4-address? inet:ipv4-address | | | | +--ro v4-prefix-length?uint8 | | | | +--ro v4-loose? boolean | | | +--:(ipv6-address) | | | | +--ro v6-address? inet:ipv6-address | | | | +--ro v6-prefix-length?uint8 | | | | +--ro v6-loose? boolean | | | +--:(as-number) | | | | +--ro as-number? uint16 | | | +--:(unnumbered-link) | | | | +--ro router-id? inet:ip-address | | | | +--ro interface-id? uint32 | | | +--:(label) | | | +--ro value? uint32 | | +--ro no-cspf? empty | | +--ro lockdown? empty Saad, et al. Expires September 21, 2016 [Page 23] Internet-Draft TE YANG Data Model March 2016 | | +--ro lsp* [source] | | +--ro source -> ../../../../../../lsps-state/lsp/source | | +--ro destination? -> ../../../../../../lsps-state/lsp/destination | | +--ro tunnel-id? -> ../../../../../../lsps-state/lsp/tunnel-id | | +--ro lsp-id? -> ../../../../../../lsps-state/lsp/lsp-id | | +--ro extended-tunnel-id? -> ../../../../../../lsps-state/lsp/extended-tunnel-id | | +--ro type? -> ../../../../../../lsps-state/lsp/type | +--rw secondary-paths* [name] | +--rw name -> ../config/name | +--rw preference? -> ../config/preference | +--rw config | | +--rw name? string | | +--rw preference? uint8 | | +--rw path-named-constraint? string | | +--rw path-selection | | | +--rw topology? te-types:topology-id | | | +--rw cost-limit? uint32 | | | +--rw hop-limit? uint8 | | | +--rw metric-type? identityref | | | +--rw tiebreaker-type?identityref | | | +--rw ignore-overload?boolean | | | +--rw tunnel-path-affinities {named-path-aff}? | | | | +--rw (style)? | | | | +--:(values) | | | | | +--rw value? uint32 | | | | | +--rw mask? uint32 | | | | +--:(named) | | | | +--rw constraints* [usage] | | | | +--rw usage identityref | | | | +--rw constraint | | | | +--rw affinity-names* [name] | | | | +--rw name string | | | +--rw tunnel-path-srlgs | | | +--rw (style)? | | | +--:(values) | | | | +--rw usage? identityref | | | | +--rw values* te-types:srlg | | | +--:(named) | | | +--rw constraints* [usage] | | | +--rw usage identityref | | | +--rw constraint | | | +--rw srlg-names* [name] Saad, et al. Expires September 21, 2016 [Page 24] Internet-Draft TE YANG Data Model March 2016 | | | +--rw name string | | +--rw (type)? | | | +--:(dynamic) | | | | +--rw dynamic? empty | | | +--:(explicit) | | | +--rw explicit-path-name? string | | | +--rw explicit-route-objects* [index] | | | +--rw index uint8 | | | +--rw explicit-route-usage? identityref | | | +--rw (type)? | | | +--:(ipv4-address) | | | | +--rw v4-address? inet:ipv4-address | | | | +--rw v4-prefix-length? uint8 | | | | +--rw v4-loose? boolean | | | +--:(ipv6-address) | | | | +--rw v6-address? inet:ipv6-address | | | | +--rw v6-prefix-length? uint8 | | | | +--rw v6-loose? boolean | | | +--:(as-number) | | | | +--rw as-number? uint16 | | | +--:(unnumbered-link) | | | | +--rw router-id? inet:ip-address | | | | +--rw interface-id? uint32 | | | +--:(label) | | | +--rw value? uint32 | | +--rw no-cspf? empty | | +--rw lockdown? empty | +--ro state | +--ro name? string | +--ro preference? uint8 | +--ro path-named-constraint? string | +--ro path-selection | | +--ro topology? te-types:topology-id | | +--ro cost-limit? uint32 | | +--ro hop-limit? uint8 | | +--ro metric-type? identityref | | +--ro tiebreaker-type? identityref | | +--ro ignore-overload? boolean | | +--ro tunnel-path-affinities {named-path-aff}? | | | +--ro (style)? | | | +--:(values) | | | | +--ro value? uint32 | | | | +--ro mask? uint32 | | | +--:(named) | | | +--ro constraints* [usage] | | | +--ro usage identityref | | | +--ro constraint | | | +--ro affinity-names* [name] Saad, et al. Expires September 21, 2016 [Page 25] Internet-Draft TE YANG Data Model March 2016 | | | +--ro name string | | +--ro tunnel-path-srlgs | | +--ro (style)? | | +--:(values) | | | +--ro usage? identityref | | | +--ro values* te-types:srlg | | +--:(named) | | +--ro constraints* [usage] | | +--ro usage identityref | | +--ro constraint | | +--ro srlg-names* [name] | | +--ro name string | +--ro (type)? | | +--:(dynamic) | | | +--ro dynamic? empty | | +--:(explicit) | | +--ro explicit-path-name? string | | +--ro explicit-route-objects* [index] | | +--ro index uint8 | | +--ro explicit-route-usage? identityref | | +--ro (type)? | | +--:(ipv4-address) | | | +--ro v4-address? inet:ipv4-address | | | +--ro v4-prefix-length? uint8 | | | +--ro v4-loose? boolean | | +--:(ipv6-address) | | | +--ro v6-address? inet:ipv6-address | | | +--ro v6-prefix-length? uint8 | | | +--ro v6-loose? boolean | | +--:(as-number) | | | +--ro as-number? uint16 | | +--:(unnumbered-link) | | | +--ro router-id? inet:ip-address | | | +--ro interface-id? uint32 | | +--:(label) | | +--ro value? uint32 | +--ro no-cspf? empty | +--ro lockdown? empty | +--ro lsp* [source] | +--ro source -> ../../../../../../../lsps-state/lsp/source | +--ro destination? -> ../../../../../../../lsps-state/lsp/destination | +--ro tunnel-id? -> ../../../../../../../lsps-state/lsp/tunnel-id | +--ro lsp-id? -> ../../../../../../../lsps-state/lsp/lsp-id | +--ro extended-tunnel-id? -> Saad, et al. Expires September 21, 2016 [Page 26] Internet-Draft TE YANG Data Model March 2016 ../../../../../../../lsps-state/lsp/extended-tunnel-id | +--ro type? -> ../../../../../../../lsps-state/lsp/type Figure 8: TE tunnels configuration and state tree 3.4. TE LSPs State Data TE LSPs are derived state data that is usually instantiated via signaling protocols. TE LSPs exists on routers as ingress (starting point of LSP), transit (mid-point of LSP ), or egress (termination point of the LSP). TE LSPs are distinguished by the 5 tuple, and LSP type (P2P or P2MP) as shown in Figure 9. In the model, the nodes holding LSPs data exist in a read-only list as shown below: Saad, et al. Expires September 21, 2016 [Page 27] Internet-Draft TE YANG Data Model March 2016 module: ietf-te +--rw te! +--ro lsps-state | +--ro lsp* [source destination tunnel-id lsp-id extended-tunnel-id type] | +--ro source inet:ip-address | +--ro destination inet:ip-address | +--ro tunnel-id uint16 | +--ro lsp-id uint16 | +--ro extended-tunnel-id inet:ip-address | +--ro type identityref | +--ro oper-status? identityref | +--ro origin-type? enumeration | +--ro lsp-resource-status? enumeration | +--ro lsp-protection-role? enumeration | +--ro lsp-operational-status? empty | +--ro lsp-record-route | | +--ro record-route-subobjects* [subobject-index] | | +--ro subobject-index uint32 | | +--ro (type)? | | +--:(ipv4-address) | | | +--ro v4-address? inet:ipv4-address | | | +--ro v4-prefix-length? uint8 | | | +--ro v4-flags? uint8 | | +--:(ipv6-address) | | | +--ro v6-address? inet:ipv6-address | | | +--ro v6-prefix-length? uint8 | | | +--ro v6-flags? uint8 | | +--:(label) | | +--ro value? uint32 | | +--ro flags? uint8 | +--ro te-dev:lsp-timers | | +--ro te-dev:life-time? uint32 | | +--ro te-dev:time-to-install? uint32 | | +--ro te-dev:time-to-die? uint32 | +--ro te-dev:downstream-info | | +--ro te-dev:nhop? inet:ip-address | | +--ro te-dev:outgoing-interface? if:interface-ref | | +--ro te-dev:neighbor? inet:ip-address | | +--ro te-dev:label? uint32 | +--ro te-dev:upstream-info | +--ro te-dev:phop? inet:ip-address | +--ro te-dev:neighbor? inet:ip-address | +--ro te-dev:label? uint32 Figure 9: TE LSPs state tree Saad, et al. Expires September 21, 2016 [Page 28] Internet-Draft TE YANG Data Model March 2016 3.5. Global RPC Data This branch of the model covers system-wide RPC execution data to trigger actions and optionally expect responses. Examples of such TE commands are to: o Clear global TE statistics of various features 3.6. Interface RPC Data This collection of data in the model defines TE interface RPC execution commands. Examples of these are to: o Clear TE statistics for all or for individual TE interfaces o Trigger immediate flooding for one or all TE interfaces 3.7. Tunnel RPC Data This branch of the model covers TE tunnel RPC execution data to trigger actions and optionally expect responses. Examples of such TE commands are: o Clear statistics for all or for individual tunnels o Trigger the tear and setup of existing tunnels or LSPs. 3.8. Global Notifications Data This branch of the model covers system-wide notifications data. The node notifies the registered events to the server using the defined notification messages. Example of such global TE events are: o Backup tunnel FRR active and not-active state transition events 3.9. Interfaces Notifications Data This branch of the model covers TE interfaces related notifications data. The TE interface configuration is used for specific events registration. Notifications are sent for registered events to the server. Example events for TE interfaces are: o Interface creation and deletion o Interface state transitions o (Soft) preemption triggers Saad, et al. Expires September 21, 2016 [Page 29] Internet-Draft TE YANG Data Model March 2016 o Fast reroute activation 3.10. Tunnel Notification Data This branch of the model covers TE tunnels related notifications data. The TE tunnels configuration is used for specific events registration. Notifications are sent for registered events to the server. Example events for TE tunnels are: o Tunnel creation and deletion events o Tunnel state up/down changes o Tunnel state reoptimization changes 4. TE Generic and Helper YANG Modules file "ietf-te-types@2016-03-20.yang" module ietf-te-types { namespace "urn:ietf:params:xml:ns:yang:ietf-te-types"; /* Replace with IANA when assigned */ prefix "te-types"; import ietf-inet-types { prefix inet; } organization "IETF Traffic Engineering Architecture and Signaling (TEAS) Working Group"; contact "WG Web: WG List: WG Chair: Lou Berger WG Chair: Vishnu Pavan Beeram Editor: Tarek Saad Editor: Rakesh Gandhi Saad, et al. Expires September 21, 2016 [Page 30] Internet-Draft TE YANG Data Model March 2016 Editor: Vishnu Pavan Beeram Editor: Himanshu Shah Editor: Xufeng Liu Editor: Xia Chen Editor: Raqib Jones Editor: Bin Wen "; description "This module contains a collection of generally useful TE specific YANG data type defintions."; revision 2016-03-20 { description "Latest revision of TE generic types"; reference "RFC3209"; } identity tunnel-type { description "Base identity from which specific tunnel types are derived."; } identity tunnel-p2p { base tunnel-type; description "TE point-to-point tunnel type."; } identity tunnel-p2mp { base tunnel-type; description "TE point-to-multipoint tunnel type."; } identity state-type { description "Base identity for TE states"; Saad, et al. Expires September 21, 2016 [Page 31] Internet-Draft TE YANG Data Model March 2016 } identity state-up { base state-type; description "State up"; } identity state-down { base state-type; description "State down"; } identity lsp-prot-type { description "Base identity from which LSP protection types are derived."; } identity lsp-prot-unprotected { description "LSP protection 'Unprotected'"; reference "RFC4872"; } identity lsp-prot-reroute-extra { description "LSP protection '(Full) Rerouting'"; reference "RFC4872"; } identity lsp-prot-reroute { description "LSP protection 'Rerouting without Extra-Traffic'"; reference "RFC4872"; } identity lsp-prot-1-for-n { description "LSP protection '1:N Protection with Extra-Traffic'"; reference "RFC4872"; } identity lsp-prot-unidir-1-to-1 { description "LSP protection '1+1 Unidirectional Protection'"; reference "RFC4872"; Saad, et al. Expires September 21, 2016 [Page 32] Internet-Draft TE YANG Data Model March 2016 } identity lsp-prot-bidir-1-to-1 { description "LSP protection '1+1 Bidirectional Protection'"; reference "RFC4872"; } identity switching-capabilities { description "Base identity for interface switching capabilities"; } identity switching-psc1 { base switching-capabilities; description "Packet-Switch Capable-1 (PSC-1)"; } identity switching-evpl { base switching-capabilities; description "Ethernet Virtual Private Line (EVPL)"; } identity switching-l2sc { base switching-capabilities; description "Layer-2 Switch Capable (L2SC)"; } identity switching-tdm { base switching-capabilities; description "Time-Division-Multiplex Capable (TDM)"; } identity switching-otn { base switching-capabilities; description "OTN-TDM capable"; } identity switching-dcsc { base switching-capabilities; description "Data Channel Switching Capable (DCSC)"; } Saad, et al. Expires September 21, 2016 [Page 33] Internet-Draft TE YANG Data Model March 2016 identity switching-lsc { base switching-capabilities; description "Lambda-Switch Capable (LSC)"; } identity switching-fsc { base switching-capabilities; description "Fiber-Switch Capable (FSC)"; } identity lsp-encoding-types { description "Base identity for encoding types"; } identity lsp-encoding-packet { base lsp-encoding-types; description "Packet LSP encoding"; } identity lsp-encoding-ethernet { base lsp-encoding-types; description "Ethernet LSP encoding"; } identity lsp-encoding-pdh { base lsp-encoding-types; description "ANSI/ETSI LSP encoding"; } identity lsp-encoding-sdh { base lsp-encoding-types; description "SDH ITU-T G.707 / SONET ANSI T1.105 LSP encoding"; } identity lsp-encoding-digital-wrapper { base lsp-encoding-types; description "Digital Wrapper LSP encoding"; } identity lsp-encoding-lambda { Saad, et al. Expires September 21, 2016 [Page 34] Internet-Draft TE YANG Data Model March 2016 base lsp-encoding-types; description "Lambda (photonic) LSP encoding"; } identity lsp-encoding-fiber { base lsp-encoding-types; description "Fiber LSP encoding"; } identity lsp-encoding-fiber-channel { base lsp-encoding-types; description "FiberChannel LSP encoding"; } identity lsp-encoding-oduk { base lsp-encoding-types; description "G.709 ODUk (Digital Path)LSP encoding"; } identity lsp-encoding-optical-channel { base lsp-encoding-types; description "Line (e.g., 8B/10B) LSP encoding"; } identity lsp-encoding-line { base lsp-encoding-types; description "Line (e.g., 8B/10B) LSP encoding"; } /* TE basic features */ feature p2mp-te { description "Indicates support for P2MP-TE"; } feature frr-te { description "Indicates support for TE FastReroute (FRR)"; } feature extended-admin-groups { description Saad, et al. Expires September 21, 2016 [Page 35] Internet-Draft TE YANG Data Model March 2016 "Indicates support for TE link extended admin groups."; } feature named-path-affinities { description "Indicates support for named path affinities"; } feature named-extended-admin-groups { description "Indicates support for named extended admin groups"; } feature named-srlg-groups { description "Indicates support for named SRLG groups"; } feature named-path-constraints { description "Indicates support for named path constraints"; } grouping explicit-route-subobject { description "The explicit route subobject grouping"; choice type { description "The explicit route subobject type"; case ipv4-address { description "IPv4 address explicit route subobject"; leaf v4-address { type inet:ipv4-address; description "An IPv4 address. This address is treated as a prefix based on the prefix length value below. Bits beyond the prefix are ignored on receipt and SHOULD be set to zero on transmission."; } leaf v4-prefix-length { type uint8; description "Length in bits of the IPv4 prefix"; } leaf v4-loose { Saad, et al. Expires September 21, 2016 [Page 36] Internet-Draft TE YANG Data Model March 2016 type boolean; description "Describes whether the object is loose if set, or otherwise strict"; } } case ipv6-address { description "IPv6 address Explicit Route Object"; leaf v6-address { type inet:ipv6-address; description "An IPv6 address. This address is treated as a prefix based on the prefix length value below. Bits beyond the prefix are ignored on receipt and SHOULD be set to zero on transmission."; } leaf v6-prefix-length { type uint8; description "Length in bits of the IPv4 prefix"; } leaf v6-loose { type boolean; description "Describes whether the object is loose if set, or otherwise strict"; } } case as-number { leaf as-number { type uint16; description "AS number"; } description "Autonomous System explicit route subobject"; } case unnumbered-link { leaf router-id { type inet:ip-address; description "A router-id address"; } leaf interface-id { type uint32; description "The interface identifier"; Saad, et al. Expires September 21, 2016 [Page 37] Internet-Draft TE YANG Data Model March 2016 } description "Unnumbered link explicit route subobject"; reference "RFC3477: Signalling Unnumbered Links in RSVP-TE"; } case label { leaf value { type uint32; description "the label value"; } description "The Label ERO subobject"; } /* AS domain sequence..? */ } } grouping record-route-subobject { description "The record route subobject grouping"; choice type { description "The record route subobject type"; case ipv4-address { leaf v4-address { type inet:ipv4-address; description "An IPv4 address. This address is treated as a prefix based on the prefix length value below. Bits beyond the prefix are ignored on receipt and SHOULD be set to zero on transmission."; } leaf v4-prefix-length { type uint8; description "Length in bits of the IPv4 prefix"; } leaf v4-flags { type uint8; description "IPv4 address sub-object flags"; reference "RFC3209"; } } case ipv6-address { Saad, et al. Expires September 21, 2016 [Page 38] Internet-Draft TE YANG Data Model March 2016 leaf v6-address { type inet:ipv6-address; description "An IPv6 address. This address is treated as a prefix based on the prefix length value below. Bits beyond the prefix are ignored on receipt and SHOULD be set to zero on transmission."; } leaf v6-prefix-length { type uint8; description "Length in bits of the IPv4 prefix"; } leaf v6-flags { type uint8; description "IPv6 address sub-object flags"; reference "RFC3209"; } } case label { leaf value { type uint32; description "the label value"; } leaf flags { type uint8; description "Label sub-object flags"; reference "RFC3209"; } description "The Label ERO subobject"; } } } identity route-usage-type { description "Base identity for route usage"; } identity route-include-ero { base route-usage-type; description "Include ERO from route"; Saad, et al. Expires September 21, 2016 [Page 39] Internet-Draft TE YANG Data Model March 2016 } identity route-exclude-ero { base route-usage-type; description "Exclude ERO from route"; } identity route-exclude-srlg { base route-usage-type; description "Exclude SRLG from route"; } identity path-metric-type { description "Base identity for path metric type"; } identity path-metric-te { base path-metric-type; description "TE path metric"; } identity path-metric-igp { base path-metric-type; description "IGP path metric"; } identity path-tiebreaker-type { description "Base identity for path tie-breaker type"; } identity path-tiebreaker-minfill { base path-tiebreaker-type; description "Min-Fill LSP path placement"; } identity path-tiebreaker-maxfill { base path-tiebreaker-type; description "Max-Fill LSP path placement"; } Saad, et al. Expires September 21, 2016 [Page 40] Internet-Draft TE YANG Data Model March 2016 identity path-tiebreaker-randoom { base path-tiebreaker-type; description "Random LSP path placement"; } identity bidir-provisioning-mode { description "Base identity for bidirectional provisioning mode."; } identity bidir-provisioning-single-sided { base bidir-provisioning-mode; description "Single-sided bidirectional provioning mode"; } identity bidir-provisioning-double-sided { base bidir-provisioning-mode; description "Double-sided bidirectional provioning mode"; } identity bidir-association-type { description "Base identity for bidirectional association type"; } identity bidir-assoc-corouted { base bidir-association-type; description "Co-routed bidirectional association type"; } identity bidir-assoc-non-corouted { base bidir-association-type; description "Non co-routed bidirectional association type"; } identity resource-affinities-type { description "Base identity for resource affinities"; } identity resource-aff-include-all { base resource-affinities-type; Saad, et al. Expires September 21, 2016 [Page 41] Internet-Draft TE YANG Data Model March 2016 description "The set of attribute filters associated with a tunnel all of which must be present for a link to be acceptable"; } identity resource-aff-include-any { base resource-affinities-type; description "The set of attribute filters associated with a tunnel any of which must be present for a link to be acceptable"; } identity resource-aff-exclude-any { base resource-affinities-type; description "The set of attribute filters associated with a tunnel any of which renders a link unacceptable"; } typedef admin-group { type binary { length 32; } description "Administrative group/Resource class/Color."; } typedef extended-admin-group { type binary; description "Extended administrative group/Resource class/Color."; } typedef admin-groups { type union { type admin-group; type extended-admin-group; } description "TE administrative group derived type"; } typedef srlg { type uint32; description "SRLG type"; } Saad, et al. Expires September 21, 2016 [Page 42] Internet-Draft TE YANG Data Model March 2016 identity path-computation-srlg-type { description "Base identity for SRLG path computation"; } identity srlg-ignore { base path-computation-srlg-type; description "Ignores SRLGs in path computation"; } identity srlg-strict { base path-computation-srlg-type; description "Include strict SRLG check in path computation"; } identity srlg-preferred { base path-computation-srlg-type; description "Include preferred SRLG check in path computation"; } identity srlg-weighted { base path-computation-srlg-type; description "Include weighted SRLG check in path computation"; } typedef te-metric { type uint32; description "TE link metric"; } typedef topology-id { type string { pattern '/?([a-zA-Z0-9\-_.]+)(/[a-zA-Z0-9\-_.]+)*'; } description "An identifier for a topology."; } /** * TE tunnel generic groupings **/ /* Tunnel path selection parameters */ Saad, et al. Expires September 21, 2016 [Page 43] Internet-Draft TE YANG Data Model March 2016 grouping tunnel-path-selection { description "Tunnel path selection properties grouping"; container path-selection { description "Tunnel path selection properties container"; leaf topology { type te-types:topology-id; description "The tunnel path is computed using the specific topology identified by this identifier"; } leaf cost-limit { type uint32 { range "1..4294967295"; } description "The tunnel path cost limit."; } leaf hop-limit { type uint8 { range "1..255"; } description "The tunnel path hop limit."; } leaf metric-type { type identityref { base path-metric-type; } default path-metric-te; description "The tunnel path metric type."; } leaf tiebreaker-type { type identityref { base path-tiebreaker-type; } default path-tiebreaker-maxfill; description "The tunnel path computation tie breakers."; } leaf ignore-overload { type boolean; description "The tunnel path can traverse overloaded node."; } uses tunnel-path-affinities; Saad, et al. Expires September 21, 2016 [Page 44] Internet-Draft TE YANG Data Model March 2016 uses tunnel-path-srlgs; } } grouping tunnel-path-affinities { description "Path affinities grouping"; container tunnel-path-affinities { if-feature named-path-affinities; description "Path affinities container"; choice style { description "Path affinities representation style"; case values { leaf value { type uint32 { range "0..4294967295"; } description "Affinity value"; } leaf mask { type uint32 { range "0..4294967295"; } description "Affinity mask"; } } case named { list constraints { key "usage"; leaf usage { type identityref { base resource-affinities-type; } description "Affinities usage"; } container constraint { description "Container for named affinities"; list affinity-names { key "name"; leaf name { type string; description "Affinity name"; Saad, et al. Expires September 21, 2016 [Page 45] Internet-Draft TE YANG Data Model March 2016 } description "List of named affinities"; } } description "List of named affinity constraints"; } } } } } grouping tunnel-path-srlgs { description "Path SRLG properties grouping"; container tunnel-path-srlgs { description "Path SRLG properties container"; choice style { description "Type of SRLG representation"; case values { leaf usage { type identityref { base route-exclude-srlg; } description "SRLG usage"; } leaf-list values { type te-types:srlg; description "SRLG value"; } } case named { list constraints { key "usage"; leaf usage { type identityref { base route-exclude-srlg; } description "SRLG usage"; } container constraint { description "Container for named SRLG list"; list srlg-names { key "name"; Saad, et al. Expires September 21, 2016 [Page 46] Internet-Draft TE YANG Data Model March 2016 leaf name { type string; description "The SRLG name"; } description "List named SRLGs"; } } description "List of named SRLG constraints"; } } } } } grouping tunnel-bidir-assoc-properties { description "TE tunnel associated bidirectional properties grouping"; container bidirectional { description "TE tunnel associated bidirectional attributes."; container association { description "Tunnel bidirectional association properties"; leaf id { type uint16; description "The TE tunnel association identifier."; } leaf source { type inet:ip-address; description "The TE tunnel association source."; } leaf global-source { type inet:ip-address; description "The TE tunnel association global source."; } leaf type { type identityref { base bidir-association-type; } default bidir-assoc-non-corouted; Saad, et al. Expires September 21, 2016 [Page 47] Internet-Draft TE YANG Data Model March 2016 description "The TE tunnel association type."; } leaf provisioing { type identityref { base bidir-provisioning-mode; } description "Describes the provisioning model of the associated bidirectional LSP"; reference "draft-ietf-teas-mpls-tp-rsvpte-ext- associated-lsp, section-3.2"; } } } } /*** End of TE tunnel groupings ***/ /** * TE interface generic groupings **/ } Figure 10: TE basic types YANG module file "ietf-te@2016-03-20.yang" module ietf-te { namespace "urn:ietf:params:xml:ns:yang:ietf-te"; /* Replace with IANA when assigned */ prefix "te"; /* Import TE generic types */ import ietf-te-types { prefix te-types; } import ietf-inet-types { prefix inet; } organization "IETF Traffic Engineering Architecture and Signaling (TEAS) Working Group"; Saad, et al. Expires September 21, 2016 [Page 48] Internet-Draft TE YANG Data Model March 2016 contact "WG Web: WG List: WG Chair: Lou Berger WG Chair: Vishnu Pavan Beeram Editor: Tarek Saad Editor: Rakesh Gandhi Editor: Vishnu Pavan Beeram Editor: Himanshu Shah Editor: Xufeng Liu Editor: Xia Chen Editor: Raqib Jones Editor: Bin Wen "; description "YANG data module for TE configuration, state, RPC and notifications."; revision 2016-03-20 { description "Latest update to TE generic YANG module."; reference "TBD"; } /** * TE tunnel generic groupings */ grouping p2p-secondary-path-params { Saad, et al. Expires September 21, 2016 [Page 49] Internet-Draft TE YANG Data Model March 2016 description "tunnel path properties."; container config { description "Configuration parameters relating to tunnel properties"; uses path-properties_config; uses path-params_config; } container state { config false; description "State information associated with tunnel properties"; uses path-properties_config; uses path-params_config; uses p2p-secondary-path-params_state; } } grouping p2p-primary-path-params { description "TE tunnel primary path properties grouping"; container config { description "Configuration parameters relating to tunnel properties"; uses path-properties_config; uses path-params_config; } container state { config false; description "State information associated with tunnel properties"; uses path-params_config; uses p2p-primary-path-params_state; } } grouping p2p-primary-path-params_state { description "TE primary path state parameters"; list lsp { key "source"; description "List of LSPs associated with the tunnel."; leaf source { type leafref { Saad, et al. Expires September 21, 2016 [Page 50] Internet-Draft TE YANG Data Model March 2016 path "../../../../../../lsps-state/lsp/source"; } description "Tunnel sender address extracted from SENDER_TEMPLATE object"; reference "RFC3209"; } leaf destination { type leafref { path "../../../../../../lsps-state/lsp/destination"; } description "Tunnel endpoint address extracted from SESSION object"; reference "RFC3209"; } leaf tunnel-id { type leafref { path "../../../../../../lsps-state/lsp/tunnel-id"; } description "Tunnel identifier used in the SESSION that remains constant over the life of the tunnel."; reference "RFC3209"; } leaf lsp-id { type leafref { path "../../../../../../lsps-state/lsp/lsp-id"; } description "Identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself."; reference "RFC3209"; } leaf extended-tunnel-id { type leafref { path "../../../../../../lsps-state/lsp/extended-tunnel-id"; } description "Extended Tunnel ID of the LSP."; reference "RFC3209"; } leaf type { type leafref { path "../../../../../../lsps-state/lsp/type"; Saad, et al. Expires September 21, 2016 [Page 51] Internet-Draft TE YANG Data Model March 2016 } description "LSP type P2P or P2MP"; } } } grouping p2p-secondary-path-params_state { description "TE secondary path state parameters"; list lsp { key "source"; description "List of LSPs associated with the tunnel."; leaf source { type leafref { path "../../../../../../../lsps-state/lsp/source"; } description "Tunnel sender address extracted from SENDER_TEMPLATE object"; reference "RFC3209"; } leaf destination { type leafref { path "../../../../../../../lsps-state/lsp/destination"; } description "Tunnel endpoint address extracted from SESSION object"; reference "RFC3209"; } leaf tunnel-id { type leafref { path "../../../../../../../lsps-state/lsp/tunnel-id"; } description "Tunnel identifier used in the SESSION that remains constant over the life of the tunnel."; reference "RFC3209"; } leaf lsp-id { type leafref { path "../../../../../../../lsps-state/lsp/lsp-id"; } description "Identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with Saad, et al. Expires September 21, 2016 [Page 52] Internet-Draft TE YANG Data Model March 2016 itself."; reference "RFC3209"; } leaf extended-tunnel-id { type leafref { path "../../../../../../../lsps-state/lsp/extended-tunnel-id"; } description "Extended Tunnel ID of the LSP."; reference "RFC3209"; } leaf type { type leafref { path "../../../../../../../lsps-state/lsp/type"; } description "LSP type P2P or P2MP"; } } } grouping path-params_config { description "TE tunnel path parameters configuration grouping"; leaf path-named-constraint { if-feature te-types:named-path-constraints; type string; description "Reference to a globally defined named path constraint set"; } uses te-types:tunnel-path-selection; choice type { description "Describes the path type"; case dynamic { leaf dynamic { type empty; description "A CSPF dynamically computed path"; } } case explicit { leaf explicit-path-name { type string; description "The explicit-path name"; } Saad, et al. Expires September 21, 2016 [Page 53] Internet-Draft TE YANG Data Model March 2016 list explicit-route-objects { key "index"; description "List of explicit route objects"; leaf index { type uint8 { range "0..255"; } description "Index of this explicit route object"; } leaf explicit-route-usage { type identityref { base te-types:route-usage-type; } description "An explicit-route hop action."; } uses te-types:explicit-route-subobject; } } } leaf no-cspf { type empty; description "Indicates no CSPF is to be attempted on this path."; } leaf lockdown { type empty; description "Indicates no reoptimization to be attempted for this path."; } } /* TE tunnel configuration data */ grouping tunnel-params_config { description "Configuration parameters relating to TE tunnel"; leaf name { type string; description "TE tunnel name."; } leaf type { type identityref { base te-types:tunnel-type; } description "TE tunnel type."; Saad, et al. Expires September 21, 2016 [Page 54] Internet-Draft TE YANG Data Model March 2016 } leaf identifier { type uint16; description "TE tunnel Identifier."; } leaf description { type string; description "Textual description for this TE tunnel"; } leaf lsp-priority-setup { type uint8 { range "0..7"; } description "TE LSP setup priority"; } leaf lsp-priority-hold { type uint8 { range "0..7"; } description "TE LSP hold priority"; } leaf lsp-protection-type { type identityref { base te-types:lsp-prot-type; } description "LSP protection type."; } leaf admin-status { type identityref { base te-types:state-type; } default te-types:state-up; description "TE tunnel administrative state."; } leaf source { type inet:ip-address; description "TE tunnel source address."; } leaf destination { /* Add when check */ type inet:ip-address; description "P2P tunnel destination address"; Saad, et al. Expires September 21, 2016 [Page 55] Internet-Draft TE YANG Data Model March 2016 } leaf src-tp-id { type binary; description "TE tunnel source termination point identifier."; } leaf tunnel-dst-tp-id { /* Add when check */ type binary; description "TE tunnel destination termination point identifier."; } uses te-types:tunnel-bidir-assoc-properties; } grouping tunnel-params_state { description "State parameters relating to TE tunnel"; leaf oper-status { type identityref { base te-types:state-type; } description "TE tunnel operational state."; } } grouping path-properties_config { description "TE path properties grouping"; leaf name { type string; description "TE path name"; } leaf preference { type uint8 { range "1..255"; } description "Specifies a preference for this path. The lower the number higher the preference"; } } /* TE tunnel configuration/state grouping */ grouping tunnel-properties { description "Top level grouping for tunnel properties."; container config { description Saad, et al. Expires September 21, 2016 [Page 56] Internet-Draft TE YANG Data Model March 2016 "Configuration parameters relating to tunnel properties"; uses tunnel-params_config; } container state { config false; description "State information associated with tunnel properties"; uses tunnel-params_config; uses tunnel-params_state; } list primary-paths { key "name"; description "List of primary paths for this tunnel."; leaf name { type leafref { path "../config/name"; } description "TE path name"; } leaf preference { type leafref { path "../config/preference"; } description "Specifies a preference for this path. The lower the number higher the preference"; } uses p2p-primary-path-params; list secondary-paths { key "name"; description "List of secondary paths for this tunnel."; leaf name { type leafref { path "../config/name"; } description "TE path name"; } leaf preference { type leafref { path "../config/preference"; } description "Specifies a preference for this path. The lower the number higher the preference"; Saad, et al. Expires September 21, 2016 [Page 57] Internet-Draft TE YANG Data Model March 2016 } uses p2p-secondary-path-params; } } } /*** End of TE tunnel groupings ***/ /** * LSP related generic groupings */ grouping lsp-record-route-information_state { description "recorded route information grouping"; container lsp-record-route { description "RSVP recorded route object information"; list record-route-subobjects { when "../origin-type != 'ingress'" { description "Applicable on non-ingress LSPs only"; } key "subobject-index"; description ""; leaf subobject-index { type uint32; description "RRO subobject index"; } uses te-types:record-route-subobject; } } } grouping lsp-properties_state { description "State parameters relating to LSP"; leaf oper-status { type identityref { base te-types:state-type; } description "LSP operational state."; } leaf origin-type { type enumeration { enum ingress { description "Origin ingress"; } enum egress { description "Origin egress"; Saad, et al. Expires September 21, 2016 [Page 58] Internet-Draft TE YANG Data Model March 2016 } enum transit { description "transit"; } } description "Origin type of LSP relative to the location of the local switch in the path."; } leaf lsp-resource-status { type enumeration { enum primary { description "A primary LSP is a fully established LSP for which the resource allocation has been committed at the data plane"; } enum secondary { description "A secondary LSP is an LSP that has been provisioned in the control plane only; e.g. resource allocation has not been committed at the data plane"; } } description "LSP resource allocation type"; reference "rfc4872, section 4.2.1"; } leaf lsp-protection-role { type enumeration { enum working { description "A working LSP must be a primary LSP whilst a protecting LSP can be either a primary or a secondary LSP. Also, known as protected LSPs when working LSPs are associated with protecting LSPs."; } enum protecting { description "A secondary LSP is an LSP that has been provisioned in the control plane only; e.g. resource allocation has not been committed at the data plane"; } } description "LSP role type"; reference "rfc4872, section 4.2.1"; Saad, et al. Expires September 21, 2016 [Page 59] Internet-Draft TE YANG Data Model March 2016 } leaf lsp-operational-status { type empty; description "This bit is set when a protecting LSP is carrying the normal traffic after protection switching"; } } /*** End of TE LSP groupings ***/ /** * TE global generic groupings */ /* Global named admin-groups configuration data */ grouping named-admin-groups_config { description "Global named administrative groups configuration grouping"; list named-admin-groups { if-feature te-types:extended-admin-groups; if-feature te-types:named-extended-admin-groups; key "name"; description "List of named TE admin-groups"; leaf name { type string; description "A string name that uniquely identifies a TE interface named admin-group"; } leaf bit-position { type uint32; description "Bit position representing the administrative group"; } } } /* Global named admin-srlgs configuration data */ grouping named-srlgs_config { description "Global named SRLGs configuration grouping"; list named-srlgs { if-feature te-types:named-srlg-groups; key "name"; Saad, et al. Expires September 21, 2016 [Page 60] Internet-Draft TE YANG Data Model March 2016 description "A list of named SRLG groups"; leaf name { type string; description "A string name that uniquely identifies a TE interface named srlg"; } leaf group { type te-types:srlg; description "An SRLG value"; } } } /* Global named explicit-paths configuration data */ grouping named-explicit-paths_config { description "Global explicit path configuration grouping"; list named-explicit-paths { key "name"; description "A list of explicit paths"; leaf name { type string; description "A string name that uniquely identifies an explicit path"; } list explicit-route-objects { key "index"; description "List of explicit route objects"; leaf index { type uint8 { range "0..255"; } description "Index of this explicit route object"; } leaf explicit-route-usage { type identityref { base te-types:route-usage-type; } description "An explicit-route hop action."; } uses te-types:explicit-route-subobject; Saad, et al. Expires September 21, 2016 [Page 61] Internet-Draft TE YANG Data Model March 2016 } } } /* Global named paths constraints configuration data */ grouping named-path-constraints_config { description "Global named path constraints configuration grouping"; list named-constraints { if-feature te-types:named-path-constraints; key "name"; description "A list of named path constraints"; leaf name { type string; description "A string name that uniquely identifies a path constraint set"; } uses te-types:tunnel-path-selection; } } /* TE globals container data */ grouping globals-grouping { description "Globals TE system-wide configuration data grouping"; container globals { description "Globals TE system-wide configuration data container"; container config { description "Configuration parameters for system-wide parameters"; uses named-admin-groups_config; uses named-srlgs_config; uses named-explicit-paths_config; uses named-path-constraints_config; } container state { config false; description "State for system-wide parameters"; uses named-admin-groups_config; uses named-srlgs_config; uses named-explicit-paths_config; uses named-path-constraints_config; Saad, et al. Expires September 21, 2016 [Page 62] Internet-Draft TE YANG Data Model March 2016 } } } /* TE tunnels container data */ grouping tunnels-grouping { description "Tunnels TE configuration data grouping"; container tunnels { description "Tunnels TE configuration data container"; list tunnel { key "name type"; unique "identifier"; description "TE tunnel."; leaf name { type leafref { path "../config/name"; } description "TE tunnel name."; } leaf type { type leafref { path "../config/type"; } description "TE tunnel type."; } leaf identifier { type leafref { path "../config/identifier"; } description "TE tunnel Identifier."; } uses tunnel-properties; } } } /* TE LSPs ephemeral state container data */ grouping lsps-state-grouping { description "LSPs state operational data grouping"; container lsps-state { config "false"; description "LSPs operational state data."; Saad, et al. Expires September 21, 2016 [Page 63] Internet-Draft TE YANG Data Model March 2016 list lsp { key "source destination tunnel-id lsp-id "+ "extended-tunnel-id type"; description "List of LSPs associated with the tunnel."; leaf source { type inet:ip-address; description "Tunnel sender address extracted from SENDER_TEMPLATE object"; reference "RFC3209"; } leaf destination { type inet:ip-address; description "Tunnel endpoint address extracted from SESSION object"; reference "RFC3209"; } leaf tunnel-id { type uint16; description "Tunnel identifier used in the SESSION that remains constant over the life of the tunnel."; reference "RFC3209"; } leaf lsp-id { type uint16; description "Identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself."; reference "RFC3209"; } leaf extended-tunnel-id { type inet:ip-address; description "Extended Tunnel ID of the LSP."; reference "RFC3209"; } leaf type { type identityref { base te-types:tunnel-type; } description "The LSP type P2P or P2MP"; Saad, et al. Expires September 21, 2016 [Page 64] Internet-Draft TE YANG Data Model March 2016 } uses lsp-properties_state; uses lsp-record-route-information_state; } } } /*** End of TE global groupings ***/ /** * TE configurations container */ container te { presence "Enable TE feature."; description "TE global container."; /* TE Global Configuration Data */ uses globals-grouping; /* TE Tunnel Configuration Data */ uses tunnels-grouping; /* TE LSPs State Data */ uses lsps-state-grouping; } /* TE Global RPCs/execution Data */ rpc globals-rpc { description "Execution data for TE global."; } /* TE interfaces RPCs/execution Data */ rpc interfaces-rpc { description "Execution data for TE interfaces."; } /* TE Tunnel RPCs/execution Data */ rpc tunnels-rpc { description "TE tunnels RPC nodes"; } /* TE Global Notification Data */ notification globals-notif { description "Notification messages for Global TE."; Saad, et al. Expires September 21, 2016 [Page 65] Internet-Draft TE YANG Data Model March 2016 } /* TE Tunnel Notification Data */ notification tunnels-notif { description "Notification messages for TE tunnels."; } } Figure 11: TE generic YANG module file "ietf-te-device@2016-03-20.yang" module ietf-te-device { namespace "urn:ietf:params:xml:ns:yang:ietf-te-device"; /* Replace with IANA when assigned */ prefix "te-dev"; /* Import TE generic types */ import ietf-te { prefix ietf-te; } /* Import TE generic types */ import ietf-te-types { prefix te-types; } import ietf-interfaces { prefix if; } import ietf-inet-types { prefix inet; } organization "IETF Traffic Engineering Architecture and Signaling (TEAS) Working Group"; contact "WG Web: WG List: WG Chair: Lou Berger Saad, et al. Expires September 21, 2016 [Page 66] Internet-Draft TE YANG Data Model March 2016 WG Chair: Vishnu Pavan Beeram Editor: Tarek Saad Editor: Rakesh Gandhi Editor: Vishnu Pavan Beeram Editor: Himanshu Shah Editor: Xufeng Liu Editor: Xia Chen Editor: Raqib Jones Editor: Bin Wen "; description "YANG data module for TE device configurations, state, RPC and notifications."; revision 2016-03-20 { description "Latest update to TE device YANG module."; reference "TBD"; } /** * TE LSP device state grouping */ grouping lsps-device_state { description "TE LSP device state grouping"; container lsp-timers { when "../origin-type = 'ingress'" { description "Applicable to ingress LSPs only"; } description "Ingress LSP timers"; leaf life-time { Saad, et al. Expires September 21, 2016 [Page 67] Internet-Draft TE YANG Data Model March 2016 type uint32; units seconds; description "lsp life time"; } leaf time-to-install { type uint32; units seconds; description "lsp installation delay time"; } leaf time-to-die { type uint32; units seconds; description "lsp expire delay time"; } } container downstream-info { when "../../origin-type != 'egress'" { description "Applicable to ingress LSPs only"; } description "downstream information"; leaf nhop { type inet:ip-address; description "downstream nexthop."; } leaf outgoing-interface { type if:interface-ref; description "downstream interface."; } leaf neighbor { type inet:ip-address; description "downstream neighbor."; } leaf label { type uint32; Saad, et al. Expires September 21, 2016 [Page 68] Internet-Draft TE YANG Data Model March 2016 description "downstream label."; } } container upstream-info { when "../../origin-type != 'ingress'" { description "Applicable to non-ingress LSPs only"; } description "upstream information"; leaf phop { type inet:ip-address; description "upstream nexthop or previous-hop."; } leaf neighbor { type inet:ip-address; description "upstream neighbor."; } leaf label { type uint32; description "upstream label."; } } } /** * TE global device generic groupings */ /* Global device specific configuration data */ grouping globals-device_config { description "Top level grouping for global config data."; leaf lsp-install-interval { type uint32; units seconds; description "lsp installation delay time"; } leaf lsp-cleanup-interval { type uint32; units seconds; Saad, et al. Expires September 21, 2016 [Page 69] Internet-Draft TE YANG Data Model March 2016 description "lsp cleanup delay time"; } } /* Global device specific state data */ grouping globals-device_state { description "Top level grouping for global state data."; leaf tunnels-counter { type uint32; description "Tunnels count"; } leaf lsps-counter { type uint32; description "Tunnels count"; } } /* TE interface container data */ grouping interfaces-grouping { description "Interface TE configuration data grouping"; container interfaces { description "Configuration data model for TE interfaces."; uses te-all-attributes; list interface { key "interface"; description "TE interfaces."; leaf interface { type if:interface-ref; description "TE interface name."; } /* TE interface parameters */ uses te-attributes; } } } /** * TE interface device generic groupings */ grouping te-admin-groups_config { description "TE interface affinities grouping"; choice admin-group-type { Saad, et al. Expires September 21, 2016 [Page 70] Internet-Draft TE YANG Data Model March 2016 description "TE interface administrative groups representation type"; case value-admin-groups { choice value-admin-group-type { description "choice of admin-groups"; case admin-groups { description "Administrative group/Resource class/Color."; leaf admin-group { type te-types:admin-group; description "TE interface administrative group"; } } case extended-admin-groups { if-feature te-types:extended-admin-groups; description "Extended administrative group/Resource class/Color."; leaf extended-admin-group { type te-types:extended-admin-group; description "TE interface extended administrativei group"; } } } } case named-admin-groups { list named-admin-groups { if-feature te-types:extended-admin-groups; if-feature te-types:named-extended-admin-groups; key named-admin-group; description "A list of named admin-group entries"; leaf named-admin-group { type leafref { path "../../../../../ietf-te:globals/ietf-te:config/" + "ietf-te:named-admin-groups/ietf-te:name"; } description "A named admin-group entry"; } } } } } Saad, et al. Expires September 21, 2016 [Page 71] Internet-Draft TE YANG Data Model March 2016 /* TE interface SRLGs */ grouping te-srlgs_config { description "TE interface SRLG grouping"; choice srlg-type { description "Choice of SRLG configuration"; case value-srlgs { list values { key "value"; description "List of SRLG values that this link is part of."; leaf value { type uint32 { range "0..4294967295"; } description "Value of the SRLG"; } } } case named-srlgs { list named-srlgs { if-feature te-types:named-srlg-groups; key named-srlg; description "A list of named SRLG entries"; leaf named-srlg { type leafref { path "../../../../../ietf-te:globals/ietf-te:config/" + "ietf-te:named-srlgs/ietf-te:name"; } description "A named SRLG entry"; } } } } } /* TE interface flooding parameters */ grouping te-flooding-parameters_config { description "Interface TE flooding properties."; container thresholds { description "Flooding threshold values in percentages."; choice type { description "Describes the flooding threshold step method"; case equal-steps { choice equal-step-type { Saad, et al. Expires September 21, 2016 [Page 72] Internet-Draft TE YANG Data Model March 2016 description "Describes whether up and down equal step size are same or different"; case up-down-different-step { leaf up-step { type uint8 { range "0..100"; } description "Set single percentage threshold for increasing resource allocation"; } leaf down-step { type uint8 { range "0..100"; } description "Set single percentage threshold for decreasing resource allocation"; } } case up-down-same-step { leaf step { type uint8 { range "0..100"; } description "Set single percentage threshold for increasing and decreasing resource allocation"; } } } } case unequal-steps { list up-steps { key "value"; description "Set nultuple percentage thresholds for increasing resource allocation"; leaf value { type uint8 { range "0..100"; } description "Percentage value"; Saad, et al. Expires September 21, 2016 [Page 73] Internet-Draft TE YANG Data Model March 2016 } } list down-steps { key "value"; description "Set nultuple percentage thresholds for decreasing resource allocation"; leaf value { type uint8 { range "0..100"; } description "Percentage value"; } } } } } } /* TE interface metric */ grouping te-metric_config { description "Interface TE metric grouping"; leaf te-metric { type te-types:te-metric; description "Interface TE metric."; } } /* TE interface switching capabilities */ grouping te-switching-cap_config { description "TE interface switching capabilities"; list switching-capabilities { key "switching-capability"; description "List of interface capabilities for this interface"; leaf switching-capability { type identityref { base te-types:switching-capabilities; } description "Switching Capability for this interface"; } leaf encoding { type identityref { base te-types:lsp-encoding-types; } Saad, et al. Expires September 21, 2016 [Page 74] Internet-Draft TE YANG Data Model March 2016 description "Encoding supported by this interface"; } } } grouping te-advertisements_state { description "TE interface advertisements state grouping"; container te-advertisements_state { description "TE interface advertisements state container"; leaf flood-interval { type uint32; description "The periodic flooding interval"; } leaf last-flooded-time { type uint32; units seconds; description "Time elapsed since last flooding in seconds"; } leaf next-flooded-time { type uint32; units seconds; description "Time remained for next flooding in seconds"; } leaf last-flooded-trigger { type enumeration { enum link-up { description "Link-up flooding trigger"; } enum link-down { description "Link-up flooding trigger"; } enum threshold-up { description "Bandwidth reservation up threshold"; } enum threshold-down { description "Bandwidth reservation down threshold"; } enum bandwidth-change { description "Banwidth capacity change"; } Saad, et al. Expires September 21, 2016 [Page 75] Internet-Draft TE YANG Data Model March 2016 enum user-initiated { description "Initiated by user"; } enum srlg-change { description "SRLG property change"; } enum periodic-timer { description "Periodic timer expired"; } } description "Trigger for the last flood"; } list advertized-level-areas { key level-area; description "List of areas the TE interface is advertised in"; leaf level-area { type uint32; description "The IGP area or level where the TE interface state is advertised in"; } } } } /* TE interface attributes grouping */ grouping te-attributes { description "TE attributes configuration grouping"; container config { description "Configuration parameters for interface TE attributes"; uses te-metric_config; uses te-admin-groups_config; uses te-srlgs_config; uses te-switching-cap_config; uses te-flooding-parameters_config; } container state { config false; description "State parameters for interface TE metric"; uses te-metric_config; uses te-admin-groups_config; uses te-srlgs_config; uses te-switching-cap_config; Saad, et al. Expires September 21, 2016 [Page 76] Internet-Draft TE YANG Data Model March 2016 uses te-flooding-parameters_config; uses te-advertisements_state; } } grouping te-all-attributes { description "TE attributes configuration grouping for all interfaces"; container config { description "Configuration parameters for all interface TE attributes"; uses te-flooding-parameters_config; } container state { config false; description "State parameters for all interface TE metric"; uses te-flooding-parameters_config; } } /*** End of TE interfaces device groupings ***/ /** * TE device augmentations */ augment "/ietf-te:te" { description "TE global container."; /* TE Interface Configuration Data */ uses interfaces-grouping; } /* TE globals device augmentation */ augment "/ietf-te:te/ietf-te:globals/ietf-te:config" { description "Global TE device specific configuration parameters"; uses globals-device_config; } augment "/ietf-te:te/ietf-te:globals/ietf-te:state" { description "Global TE device specific state parameters"; uses globals-device_config; uses globals-device_state; } /* TE LSPs device state augmentation */ Saad, et al. Expires September 21, 2016 [Page 77] Internet-Draft TE YANG Data Model March 2016 augment "/ietf-te:te/ietf-te:lsps-state/ietf-te:lsp" { description "LSP device dependent downstream info augmentation"; uses lsps-device_state; } /* TE interfaces RPCs/execution Data */ rpc interfaces-rpc { description "Execution data for TE interfaces."; } /* TE Interfaces Notification Data */ notification interfaces-notif { description "Notification messages for TE interfaces."; } } Figure 12: TE device YANG module file "ietf-te-mpls-types@2016-03-20.yang" module ietf-te-mpls-types { namespace "urn:ietf:params:xml:ns:yang:ietf-te-mpls-types"; /* Replace with IANA when assigned */ prefix "te-mpls-types"; import ietf-inet-types { prefix inet; } organization "IETF TEAS Working Group"; contact "Fill me"; description "This module contains a collection of generally useful TE specific YANG data type defintions."; revision 2016-03-20 { description "Latest revision of TE MPLS types"; reference "RFC3209"; } /* Describes egress LSP label allocation */ typedef egress-label { Saad, et al. Expires September 21, 2016 [Page 78] Internet-Draft TE YANG Data Model March 2016 type enumeration { enum "IPv4-EXPLICIT-NULL" { description "Use IPv4 explicit-NULL MPLS label at the egress"; } enum "IPv6-EXPLICIT-NULL" { description "Use IPv6 explicit-NULL MPLS label at the egress"; } enum "IMPLICIT-NULL" { description "Use implicit-NULL MPLS label at the egress"; } enum "NON-NULL"{ description "Use a non NULL MPLS label at the egress"; } } description "Describes egress label allocation"; } identity backup-type { description "Base identity for backup protection types"; } identity backup-facility { base backup-type; description "Use facility backup to protect LSPs traversing protected TE interface"; reference "RFC49090: RSVP-TE Fast Reroute"; } identity backup-detour { base backup-type; description "Use detour or 1-for-1 protection"; reference "RFC49090: RSVP-TE Fast Reroute"; } identity backup-protection-type { description Saad, et al. Expires September 21, 2016 [Page 79] Internet-Draft TE YANG Data Model March 2016 "Base identity for backup protection type"; } identity backup-protection-link { base backup-protection-type; description "backup provides link protection only"; } identity backup-protection-node-link { base backup-protection-type; description "backup offers node (preferred) or link protection"; } identity bc-model-type { description "Base identity for Diffserv-TE bandwidth constraint model type"; } identity bc-model-rdm { base bc-model-type; description "Russian Doll bandwidth constraint model type."; } identity bc-model-mam { base bc-model-type; description "Maximum Allocation bandwidth constraint model type."; } identity bc-model-mar { base bc-model-type; description "Maximum Allocation with Reservation bandwidth constraint model type."; } grouping bandwidth-constraint-values { description "Packet bandwidth contraints values"; choice value-type { description "Value representation"; case percentages { Saad, et al. Expires September 21, 2016 [Page 80] Internet-Draft TE YANG Data Model March 2016 container perc-values { uses bandwidth-mpls-constraints; description "Percentage values"; } } case absolutes { container abs-values { uses bandwidth-mpls-constraints; description "Absolute values"; } } } } grouping bandwidth-mpls-reservable { description "Packet reservable bandwidth"; choice bandwidth-value { description "Reservable bandwidth configuraiton choice"; case absolute { leaf absolute-value { type uint32; description "Absolute value of the bandwidth"; } } case precentage { leaf percent-value { type uint32 { range "0..4294967295"; } description "Percentage reservable bandwidth"; } description "The maximum reservable bandwidth on the interface"; } } choice bc-model-type { description "Reservable bandwidth percentage capacity values."; case bc-model-rdm { container bc-model-rdm { description "Russian Doll Model Bandwidth Constraints."; uses bandwidth-mpls-constraints; Saad, et al. Expires September 21, 2016 [Page 81] Internet-Draft TE YANG Data Model March 2016 } } case bc-model-mam { container bc-model-mam { uses bandwidth-mpls-constraints; description "Maximum Allocation Model Bandwidth Constraints."; } } case bc-model-mar { container bc-model-mar { uses bandwidth-mpls-constraints; description "Maximum Allocation with Reservation Model Bandwidth Constraints."; } } } } typedef bfd-type { type enumeration { enum classical { description "BFD classical session type."; } enum seamless { description "BFD seamless session type."; } } default "classical"; description "Type of BFD session"; } typedef bfd-encap-mode-type { type enumeration { enum gal { description "BFD with GAL mode"; } enum ip { description "BFD with IP mode"; } } default ip; description Saad, et al. Expires September 21, 2016 [Page 82] Internet-Draft TE YANG Data Model March 2016 "Possible BFD transport modes when running over TE LSPs."; } grouping bandwidth-mpls-constraints { description "Bandwidth constraints."; container bandwidth-mpls-constraints { description "Holds the bandwidth contraints properties"; leaf maximum-reservable { type uint32 { range "0..4294967295"; } description "The maximum reservable bandwidth on the interface"; } leaf-list bc-value { type uint32 { range "0..4294967295"; } max-elements 8; description "The bandwidth contraint type"; } } } grouping tunnel-forwarding-properties { description "Properties for using tunnel in forwarding."; container forwarding { description "Tunnel forwarding properties container"; leaf load-share { type uint32 { range "1..4294967295"; } description "ECMP tunnel forwarding load-share factor."; } choice policy-type { description "Tunnel policy type"; container class { description "Tunnel forwarding per class properties"; leaf class { type uint8 { Saad, et al. Expires September 21, 2016 [Page 83] Internet-Draft TE YANG Data Model March 2016 range "1..7"; } description "The class associated with this tunnel"; } } container group { description "Tunnel frowarding per group properties"; leaf-list classes { type uint8 { range "1..7"; } description "The forwarding class"; } } } } } grouping tunnel-routing-properties { description "TE tunnel routing properties"; choice routing-choice { description "Announces the tunnel to IGP as either autoroute or forwarding adjacency."; case autoroute { container autoroute-announce { presence "Enable autoroute announce."; description "Announce the TE tunnel as autoroute to IGP for use as IGP shortcut."; leaf-list routing-afs { type inet:ip-version; description "Address families"; } choice metric-type { description "Type of metric to use when announcing the tunnel as shortcut"; leaf metric { type uint32 { range "1..2147483647"; } description Saad, et al. Expires September 21, 2016 [Page 84] Internet-Draft TE YANG Data Model March 2016 "Describes the metric to use when announcing the tunnel as shortcut"; } leaf relative-metric { type int32 { range "-10..10"; } description "Relative TE metric to use when announcing the tunnel as shortcut"; } leaf absolute-metric { type uint32 { range "1..2147483647"; } description "Absolute TE metric to use when announcing the tunnel as shortcut"; } } } } case forwarding-adjacency { container forwarding-adjacency { presence "Enable forwarding adjacency on the tunnel."; description "Announce the TE tunnel as forwarding adjacency."; leaf holdtime { type uint32 { range "0..4294967295"; } description "Holdtime in seconds after tunnel becomes UP."; } leaf-list routing-afs { type inet:ip-version; description "Address families"; } } } } } } Saad, et al. Expires September 21, 2016 [Page 85] Internet-Draft TE YANG Data Model March 2016 Figure 13: TE MPLS specific types YANG module file "ietf-te-mpls@2016-03-20.yang" module ietf-te-mpls { namespace "urn:ietf:params:xml:ns:yang:ietf-te-mpls"; /* Replace with IANA when assigned */ prefix "te-mpls"; /* Import TE generic types */ import ietf-te { prefix te; } /* Import MPLS TE specific types */ import ietf-te-mpls-types { prefix te-mpls-type; } organization "IETF Traffic Engineering Architecture and Signaling (TEAS) Working Group"; contact "WG Web: WG List: WG Chair: Lou Berger WG Chair: Vishnu Pavan Beeram Editor: Tarek Saad Editor: Rakesh Gandhi Editor: Vishnu Pavan Beeram Editor: Himanshu Shah Editor: Xufeng Liu Saad, et al. Expires September 21, 2016 [Page 86] Internet-Draft TE YANG Data Model March 2016 Editor: Xia Chen Editor: Raqib Jones Editor: Bin Wen "; description "YANG data module for MPLS TE configurations, state, RPC and notifications."; revision 2016-03-20 { description "Latest update to MPLS TE YANG module."; reference "TBD"; } /* MPLS TE tunnel properties*/ grouping tunnel-mpls-properties_config { description "MPLS TE tunnel properties"; uses te-mpls-type:tunnel-routing-properties; uses te-mpls-type:tunnel-forwarding-properties; } /*** End of MPLS TE tunnel configuration/state */ /** * MPLS TE augmentations */ /* MPLS TE tunnel augmentations */ augment "/te:te/te:tunnels/te:tunnel/te:config" { description "MPLS TE tunnel config augmentations"; uses tunnel-mpls-properties_config; } augment "/te:te/te:tunnels/te:tunnel/te:state" { description "MPLS TE tunnel state augmentations"; uses tunnel-mpls-properties_config; } /* MPLS TE LSPs augmentations */ } Figure 14: TE MPLS YANG module Saad, et al. Expires September 21, 2016 [Page 87] Internet-Draft TE YANG Data Model March 2016 5. IANA Considerations This document registers the following URIs in the IETF XML registry [RFC3688]. Following the format in [RFC3688], the following registration is requested to be made. URI: urn:ietf:params:xml:ns:yang:ietf-te XML: N/A, the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-te-device XML: N/A, the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-te-mpls XML: N/A, the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-te-types XML: N/A, the requested URI is an XML namespace. URI: urn:ietf:params:xml:ns:yang:ietf-te-mpls-types XML: N/A, the requested URI is an XML namespace. This document registers a YANG module in the YANG Module Names registry [RFC6020]. name: ietf-te namespace: urn:ietf:params:xml:ns:yang:ietf-te prefix: ietf-te reference: RFC3209 name: ietf-te-device namespace: urn:ietf:params:xml:ns:yang:ietf-te prefix: ietf-te-device reference: RFC3209 name: ietf-te-mpls namespace: urn:ietf:params:xml:ns:yang:ietf-te- mpls prefix: ietf-te-mpls reference: RFC3209 name: ietf-te-types namespace: urn:ietf:params:xml:ns:yang:ietf-te- types prefix: ietf-te-types reference: RFC3209 name: ietf-te-mpls-types namespace: urn:ietf:params:xml:ns:yang:ietf- te-mpls-types prefix: ietf-te-mpls-types reference: RFC3209 6. Security Considerations The YANG module defined in this memo is designed to be accessed via the NETCONF protocol [RFC6241]. The lowest NETCONF layer is the secure transport layer and the mandatory-to-implement secure transport is SSH [RFC6242]. The NETCONF access control model [RFC6536] provides means to restrict access for particular NETCONF Saad, et al. Expires September 21, 2016 [Page 88] Internet-Draft TE YANG Data Model March 2016 users to a pre-configured subset of all available NETCONF protocol operations and content. There are a number of data nodes defined in the YANG module which are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., ) to these data nodes without proper protection can have a negative effect on network operations. Following are the subtrees and data nodes and their sensitivity/vulnerability: "/te/globals": This module specifies the global TE configurations on a device. Unauthorized access to this container could cause the device to ignore packets it should receive and process. "/te/tunnels": This list specifies the configured TE tunnels on a device. Unauthorized access to this list could cause the device to ignore packets it should receive and process. "/te/lsps-state": This list specifies the state derived LSPs. Unauthorized access to this list could cause the device to ignore packets it should receive and process. "/te/interfaces": This list specifies the configured TE interfaces on a device. Unauthorized access to this list could cause the device to ignore packets it should receive and process. 7. Acknowledgement The authors would like to thank the members of the multi-vendor YANG design team who are involved in the definition of this model. The authors would also like to thank Loa Andersson, Lou Berger, Igor Bryskin, Aihua Guo, and Xian Zhang for their comments and providing valuable feedback on this document. 8. References 8.1. Normative References [I-D.bjorklund-netmod-structural-mount] Bjorklund, M., "YANG Structural Mount", draft-bjorklund- netmod-structural-mount-02 (work in progress), February 2016. Saad, et al. Expires September 21, 2016 [Page 89] Internet-Draft TE YANG Data Model March 2016 [I-D.ietf-netmod-routing-cfg] Lhotka, L. and A. Lindem, "A YANG Data Model for Routing Management", draft-ietf-netmod-routing-cfg-21 (work in progress), March 2016. [I-D.ietf-teas-yang-rsvp] Beeram, V., Gandhi, R., Liu, X., Saad, T., Chen, X., Jones, R., and B. Wen, "A YANG Data Model for Resource Reservation Protocol (RSVP)", draft-ietf-teas-yang-rsvp-01 (work in progress), October 2015. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/ RFC2119, March 1997, . [RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001, . [RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol- Traffic Engineering (RSVP-TE) Extensions", RFC 3473, DOI 10.17487/RFC3473, January 2003, . [RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, January 2004, . [RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010, . [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, . [RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011, . Saad, et al. Expires September 21, 2016 [Page 90] Internet-Draft TE YANG Data Model March 2016 [RFC6536] Bierman, A. and M. Bjorklund, "Network Configuration Protocol (NETCONF) Access Control Model", RFC 6536, DOI 10.17487/RFC6536, March 2012, . [RFC6991] Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, July 2013, . 8.2. Informative References [I-D.clemm-netmod-mount] Clemm, A., Medved, J., and E. Voit, "Mounting YANG-Defined Information from Remote Datastores", draft-clemm-netmod- mount-03 (work in progress), April 2015. [I-D.openconfig-mpls-consolidated-model] George, J., Fang, L., eric.osborne@level3.com, e., and R. Shakir, "MPLS / TE Model for Service Provider Networks", draft-openconfig-mpls-consolidated-model-02 (work in progress), October 2015. [I-D.openconfig-netmod-opstate] Shakir, R., Shaikh, A., and M. Hines, "Consistent Modeling of Operational State Data in YANG", draft-openconfig- netmod-opstate-01 (work in progress), July 2015. Authors' Addresses Tarek Saad (editor) Cisco Systems Inc Email: tsaad@cisco.com Rakesh Gandhi Cisco Systems Inc Email: rgandhi@cisco.com Xufeng Liu Ericsson Email: xufeng.liu@ericsson.com Saad, et al. Expires September 21, 2016 [Page 91] Internet-Draft TE YANG Data Model March 2016 Vishnu Pavan Beeram Juniper Networks Email: vbeeram@juniper.net Himanshu Shah Ciena Email: hshah@ciena.com Xia Chen Huawei Technologies Email: jescia.chenxia@huawei.com Raqib Jones Brocade Email: raqib@Brocade.com Bin Wen Comcast Email: Bin_Wen@cable.comcast.com Saad, et al. Expires September 21, 2016 [Page 92]