TCPM L. Xu
Internet-Draft UNL
Obsoletes: 8312 (if approved) S. Ha
Intended status: Standards Track Colorado
Expires: 27 January 2022 I. Rhee
Bowery
V. Goel
Apple Inc.
L. Eggert, Ed.
NetApp
26 July 2021
CUBIC for Fast and Long-Distance Networks
draft-ietf-tcpm-rfc8312bis-03
Abstract
CUBIC is a standard TCP congestion control algorithm that uses a
cubic function instead of the linear window increase function on the
sender side to improve scalability and stability over fast and long-
distance networks. CUBIC has been adopted as the default TCP
congestion control algorithm by the Linux, Windows, and Apple stacks.
This document updates the specification of CUBIC to include
algorithmic improvements based on these implementations and recent
academic work. Based on the extensive deployment experience with
CUBIC, it also moves the specification to the Standards Track,
obsoleting [RFC8312].
Note to Readers
Discussion of this draft takes place on the TCPM working group
mailing list (mailto:tcpm@ietf.org), which is archived at
https://mailarchive.ietf.org/arch/browse/tcpm/.
Working Group information can be found at
https://datatracker.ietf.org/wg/tcpm/; source code and issues list
for this draft can be found at https://github.com/NTAP/rfc8312bis.
Note to the RFC Editor
xml2rfc currently renders "" in the XML by surrounding the
corresponding text with underscores. This is highly distracting;
please manually remove the underscores when doing the final edits to
the text version of this document.
Xu, et al. Expires 27 January 2022 [Page 1]
Internet-Draft CUBIC July 2021
(There is an issue open against xml2rfc to stop doing this in the
future: https://trac.tools.ietf.org/tools/xml2rfc/trac/ticket/596)
Also, please manually change "Figure" to "Equation" for all artwork
with anchors beginning with "eq" - xml2rfc doesn't seem to be able to
do this.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on 27 January 2022.
Copyright Notice
Copyright (c) 2021 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents (https://trustee.ietf.org/
license-info) in effect on the date of publication of this document.
Please review these documents carefully, as they describe your rights
and restrictions with respect to this document. Code Components
extracted from this document must include Simplified BSD License text
as described in Section 4.e of the Trust Legal Provisions and are
provided without warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Design Principles of CUBIC . . . . . . . . . . . . . . . . . 5
3.1. Principle 1 for the CUBIC Increase Function . . . . . . . 5
3.2. Principle 2 for AIMD Friendliness . . . . . . . . . . . . 6
3.3. Principle 3 for RTT Fairness . . . . . . . . . . . . . . 7
3.4. Principle 4 for the CUBIC Decrease Factor . . . . . . . . 7
4. CUBIC Congestion Control . . . . . . . . . . . . . . . . . . 8
Xu, et al. Expires 27 January 2022 [Page 2]
Internet-Draft CUBIC July 2021
4.1. Definitions . . . . . . . . . . . . . . . . . . . . . . . 8
4.1.1. Constants of Interest . . . . . . . . . . . . . . . . 8
4.1.2. Variables of Interest . . . . . . . . . . . . . . . . 8
4.2. Window Increase Function . . . . . . . . . . . . . . . . 9
4.3. AIMD-Friendly Region . . . . . . . . . . . . . . . . . . 11
4.4. Concave Region . . . . . . . . . . . . . . . . . . . . . 13
4.5. Convex Region . . . . . . . . . . . . . . . . . . . . . . 13
4.6. Multiplicative Decrease . . . . . . . . . . . . . . . . . 13
4.7. Fast Convergence . . . . . . . . . . . . . . . . . . . . 14
4.8. Timeout . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.9. Spurious Congestion Events . . . . . . . . . . . . . . . 15
4.10. Slow Start . . . . . . . . . . . . . . . . . . . . . . . 17
5. Discussion . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1. Fairness to AIMD TCP . . . . . . . . . . . . . . . . . . 18
5.2. Using Spare Capacity . . . . . . . . . . . . . . . . . . 20
5.3. Difficult Environments . . . . . . . . . . . . . . . . . 21
5.4. Investigating a Range of Environments . . . . . . . . . . 21
5.5. Protection against Congestion Collapse . . . . . . . . . 21
5.6. Fairness within the Alternative Congestion Control
Algorithm . . . . . . . . . . . . . . . . . . . . . . . 21
5.7. Performance with Misbehaving Nodes and Outside
Attackers . . . . . . . . . . . . . . . . . . . . . . . 21
5.8. Behavior for Application-Limited Flows . . . . . . . . . 21
5.9. Responses to Sudden or Transient Events . . . . . . . . . 22
5.10. Incremental Deployment . . . . . . . . . . . . . . . . . 22
6. Security Considerations . . . . . . . . . . . . . . . . . . . 22
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22
8. References . . . . . . . . . . . . . . . . . . . . . . . . . 22
8.1. Normative References . . . . . . . . . . . . . . . . . . 22
8.2. Informative References . . . . . . . . . . . . . . . . . 23
Appendix A. Acknowledgments . . . . . . . . . . . . . . . . . . 26
Appendix B. Evolution of CUBIC . . . . . . . . . . . . . . . . . 26
B.1. Since draft-ietf-tcpm-rfc8312bis-02 . . . . . . . . . . . 26
B.2. Since draft-ietf-tcpm-rfc8312bis-01 . . . . . . . . . . . 26
B.3. Since draft-ietf-tcpm-rfc8312bis-00 . . . . . . . . . . . 26
B.4. Since draft-eggert-tcpm-rfc8312bis-03 . . . . . . . . . . 26
B.5. Since draft-eggert-tcpm-rfc8312bis-02 . . . . . . . . . . 27
B.6. Since draft-eggert-tcpm-rfc8312bis-01 . . . . . . . . . . 27
B.7. Since draft-eggert-tcpm-rfc8312bis-00 . . . . . . . . . . 27
B.8. Since RFC8312 . . . . . . . . . . . . . . . . . . . . . . 28
B.9. Since the Original Paper . . . . . . . . . . . . . . . . 28
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 29
Xu, et al. Expires 27 January 2022 [Page 3]
Internet-Draft CUBIC July 2021
1. Introduction
CUBIC has been adopted as the default TCP congestion control
algorithm in the Linux, Windows, and Apple stacks, and has been used
and deployed globally. Extensive, decade-long deployment experience
in vastly different Internet scenarios has convincingly demonstrated
that CUBIC is safe for deployment on the global Internet and delivers
substantial benefits over classical AIMD congestion control. It is
therefore to be regarded as the current standard for TCP congestion
control. CUBIC can also be used for other transport protocols such
as QUIC [RFC9000] and SCTP [RFC4960] as a default congestion
controller.
The design of CUBIC was motivated by the well-documented problem
classical TCP has with low utilization over fast and long-distance
networks [K03][RFC3649]. This problem arises from a slow increase of
the congestion window following a congestion event in a network with
a large bandwidth-delay product (BDP). [HKLRX06] indicates that this
problem is frequently observed even in the range of congestion window
sizes over several hundreds of packets. This problem is equally
applicable to all Reno-style TCP standards and their variants,
including TCP-Reno [RFC5681], TCP-NewReno [RFC6582][RFC6675], SCTP
[RFC4960], and TFRC [RFC5348], which use the same linear increase
function for window growth. We refer to all Reno-style TCP standards
and their variants collectively as "AIMD TCP" below because they use
the Additive Increase and Multiplicative Decrease algorithm (AIMD).
CUBIC, originally proposed in [HRX08], is a modification to the
congestion control algorithm of classical AIMD TCP to remedy this
problem. This document describes the most recent specification of
CUBIC. Specifically, CUBIC uses a cubic function instead of the
linear window increase function of AIMD TCP to improve scalability
and stability under fast and long-distance networks.
Binary Increase Congestion Control (BIC-TCP) [XHR04], a predecessor
of CUBIC, was selected as the default TCP congestion control
algorithm by Linux in the year 2005 and had been used for several
years by the Internet community at large.
CUBIC uses a similar window increase function as BIC-TCP and is
designed to be less aggressive and fairer to AIMD TCP in bandwidth
usage than BIC-TCP while maintaining the strengths of BIC-TCP such as
stability, window scalability, and round-trip time (RTT) fairness.
In the following sections, we first briefly explain the design
principles of CUBIC, then provide the exact specification of CUBIC,
and finally discuss the safety features of CUBIC following the
guidelines specified in [RFC5033].
Xu, et al. Expires 27 January 2022 [Page 4]
Internet-Draft CUBIC July 2021
2. Conventions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
3. Design Principles of CUBIC
CUBIC is designed according to the following design principles:
Principle 1: For better network utilization and stability, CUBIC
uses both the concave and convex profiles of a cubic function to
increase the congestion window size, instead of using just a
convex function.
Principle 2: To be AIMD-friendly, CUBIC is designed to behave like
AIMD TCP in networks with short RTTs and small bandwidth where
AIMD TCP performs well.
Principle 3: For RTT-fairness, CUBIC is designed to achieve linear
bandwidth sharing among flows with different RTTs.
Principle 4: CUBIC appropriately sets its multiplicative window
decrease factor in order to balance between the scalability and
convergence speed.
3.1. Principle 1 for the CUBIC Increase Function
For better network utilization and stability, CUBIC [HRX08] uses a
cubic window increase function in terms of the elapsed time from the
last congestion event. While most alternative congestion control
algorithms to AIMD TCP increase the congestion window using convex
functions, CUBIC uses both the concave and convex profiles of a cubic
function for window growth.
Xu, et al. Expires 27 January 2022 [Page 5]
Internet-Draft CUBIC July 2021
After a window reduction in response to a congestion event detected
by duplicate ACKs, Explicit Congestion Notification-Echo (ECN-Echo,
ECE) ACKs [RFC3168], TCP RACK [RFC8985] or QUIC loss detection
[RFC9002], CUBIC remembers the congestion window size at which it
received the congestion event and performs a multiplicative decrease
of the congestion window. When CUBIC enters into congestion
avoidance, it starts to increase the congestion window using the
concave profile of the cubic function. The cubic function is set to
have its plateau at the remembered congestion window size, so that
the concave window increase continues until then. After that, the
cubic function turns into a convex profile and the convex window
increase begins.
This style of window adjustment (concave and then convex) improves
the algorithm stability while maintaining high network utilization
[CEHRX07]. This is because the window size remains almost constant,
forming a plateau around the remembered congestion window size of the
last congestion event, where network utilization is deemed highest.
Under steady state, most window size samples of CUBIC are close to
that remembered congestion window size, thus promoting high network
utilization and stability.
Note that congestion control algorithms that only use convex
functions to increase the congestion window size have their maximum
increments around the remembered congestion window size of the last
congestion event, and thus introduce many packet bursts around the
saturation point of the network, likely causing frequent global loss
synchronizations.
3.2. Principle 2 for AIMD Friendliness
CUBIC promotes per-flow fairness to AIMD TCP. Note that AIMD TCP
performs well over paths with short RTTs and small bandwidths (or
small BDPs). There is only a scalability problem in networks with
long RTTs and large bandwidths (or large BDPs).
A congestion control algorithm designed to be friendly to AIMD TCP on
a per-flow basis must increase its congestion window less
aggressively in small BDP networks than in large BDP networks.
The aggressiveness of CUBIC mainly depends on the maximum window size
before a window reduction, which is smaller in small-BDP networks
than in large-BDP networks. Thus, CUBIC increases its congestion
window less aggressively in small-BDP networks than in large-BDP
networks.
Xu, et al. Expires 27 January 2022 [Page 6]
Internet-Draft CUBIC July 2021
Furthermore, in cases when the cubic function of CUBIC would increase
the congestion window less aggressively than AIMD TCP, CUBIC simply
follows the window size of AIMD TCP to ensure that CUBIC achieves at
least the same throughput as AIMD TCP in small-BDP networks. We call
this region where CUBIC behaves like AIMD TCP the "AIMD-friendly
region".
3.3. Principle 3 for RTT Fairness
Two CUBIC flows with different RTTs have a throughput ratio that is
linearly proportional to the inverse of their RTT ratio, where the
throughput of a flow is approximately the size of its congestion
window divided by its RTT.
Specifically, CUBIC maintains a window increase rate independent of
RTTs outside the AIMD-friendly region, and thus flows with different
RTTs have similar congestion window sizes under steady state when
they operate outside the AIMD-friendly region.
This notion of a linear throughput ratio is similar to that of AIMD
TCP under high statistical multiplexing where packet loss is
independent of individual flow rates. However, under low statistical
multiplexing, the throughput ratio of AIMD TCP flows with different
RTTs is quadratically proportional to the inverse of their RTT ratio
[XHR04].
CUBIC always ensures a linear throughput ratio independent of the
amount of statistical multiplexing. This is an improvement over AIMD
TCP. While there is no consensus on particular throughput ratios for
different RTT flows, we believe that over wired Internet paths, use
of a linear throughput ratio seems more reasonable than equal
throughputs (i.e., the same throughput for flows with different RTTs)
or a higher-order throughput ratio (e.g., a quadratical throughput
ratio of AIMD TCP under low statistical multiplexing environments).
3.4. Principle 4 for the CUBIC Decrease Factor
To balance between scalability and convergence speed, CUBIC sets the
multiplicative window decrease factor to 0.7, whereas AIMD TCP uses
0.5.
While this improves the scalability of CUBIC, a side effect of this
decision is slower convergence, especially under low statistical
multiplexing. This design choice is following the observation that
HighSpeed TCP (HSTCP) [RFC3649] and other approaches (e.g., [GV02])
made: the current Internet becomes more asynchronous with less
frequent loss synchronizations under high statistical multiplexing.
Xu, et al. Expires 27 January 2022 [Page 7]
Internet-Draft CUBIC July 2021
In such environments, even strict Multiplicative-Increase
Multiplicative-Decrease (MIMD) can converge. CUBIC flows with the
same RTT always converge to the same throughput independent of
statistical multiplexing, thus achieving intra-algorithm fairness.
We also find that in environments with sufficient statistical
multiplexing, the convergence speed of CUBIC is reasonable.
4. CUBIC Congestion Control
In this section, we discuss how the congestion window is updated
during the different stages of the CUBIC congestion controller.
4.1. Definitions
The unit of all window sizes in this document is segments of the
maximum segment size (MSS), and the unit of all times is seconds.
Implementations can use bytes to express window sizes, which would
require factoring in the maximum segment size wherever necessary and
replacing _segments_acked_ with the number of bytes acknowledged in
Figure 4.
4.1.1. Constants of Interest
β__cubic_: CUBIC multiplication decrease factor as described in
Section 4.6.
α__cubic_: CUBIC additive increase factor used in AIMD-friendly
region as described in Section 4.3.
_C_: constant that determines the aggressiveness of CUBIC in
competing with other congestion control algorithms in high BDP
networks. Please see Section 5 for more explanation on how it is
set. The unit for _C_ is
segment
-------
3
second
4.1.2. Variables of Interest
This section defines the variables required to implement CUBIC:
_RTT_: Smoothed round-trip time in seconds, calculated as described
in [RFC6298].
_cwnd_: Current congestion window in segments.
Xu, et al. Expires 27 January 2022 [Page 8]
Internet-Draft CUBIC July 2021
_ssthresh_: Current slow start threshold in segments.
_W_max_: Size of _cwnd_ in segments just before _cwnd_ was reduced in
the last congestion event when fast convergence is disabled.
However, if fast convergence is enabled, the size may be further
reduced based on the current saturation point.
_K_: The time period in seconds it takes to increase the congestion
window size at the beginning of the current congestion avoidance
stage to _W_max_.
_current_time_: Current time of the system in seconds.
_epoch_start_: The time in seconds at which the current congestion
avoidance stage started.
_cwnd_start_: The _cwnd_ at the beginning of the current congestion
avoidance stage, i.e., at time _epoch_start_.
W_cubic(_t_): The congestion window in segments at time _t_ in
seconds based on the cubic increase function, as described in
Section 4.2.
_target_: Target value of congestion window in segments after the
next RTT, that is, W_cubic(_t_ + _RTT_), as described in Section 4.2.
_W_est_: An estimate for the congestion window in segments in the
AIMD-friendly region, that is, an estimate for the congestion window
of AIMD TCP.
_segments_acked_: Number of MSS-sized segments acked when an ACK is
received. This number will be a decimal value when an ACK
acknowledges an amount of data that is not MSS-sized. Specifically,
it can be less than 1 when an ACK acknowledges a segment smaller than
the MSS.
4.2. Window Increase Function
CUBIC maintains the acknowledgment (ACK) clocking of AIMD TCP by
increasing the congestion window only at the reception of an ACK. It
does not make any changes to the TCP Fast Recovery and Fast
Retransmit algorithms [RFC6582][RFC6675].
During congestion avoidance, after a congestion event is detected by
mechanisms described in Section 3.1, CUBIC changes the window
increase function of AIMD TCP.
CUBIC uses the following window increase function:
Xu, et al. Expires 27 January 2022 [Page 9]
Internet-Draft CUBIC July 2021
3
W (t) = C * (t - K) + W
cubic max
Figure 1
where _t_ is the elapsed time in seconds from the beginning of the
current congestion avoidance stage, that is,
t = current_time - epoch
start
and where _epoch_start_ is the time at which the current congestion
avoidance stage starts. _K_ is the time period that the above
function takes to increase the congestion window size at the
beginning of the current congestion avoidance stage to _W_max_ if
there are no further congestion events and is calculated using the
following equation:
________________
/W - cwnd
3 / max start
K = | / ----------------
|/ C
Figure 2
where _cwnd_start_ is the congestion window at the beginning of the
current congestion avoidance stage. For example, right after a
congestion event, _cwnd_start_ is equal to the new cwnd calculated as
described in Section 4.6.
Upon receiving an ACK during congestion avoidance, CUBIC computes the
_target_ congestion window size after the next _RTT_ using Figure 1
as follows, where _RTT_ is the smoothed round-trip time. The lower
and upper bounds below ensure that CUBIC's congestion window increase
rate is non-decreasing and is less than the increase rate of slow
start.
Xu, et al. Expires 27 January 2022 [Page 10]
Internet-Draft CUBIC July 2021
/
| if W (t + RTT) < cwnd
|cwnd cubic
|
|
|
target = < if W (t + RTT) > 1.5 * cwnd
|1.5 * cwnd cubic
|
|
|W (t + RTT)
| cubic otherwise
\
Depending on the value of the current congestion window size _cwnd_,
CUBIC runs in three different regions:
1. The AIMD-friendly region, which ensures that CUBIC achieves at
least the same throughput as AIMD TCP.
2. The concave region, if CUBIC is not in the AIMD-friendly region
and _cwnd_ is less than _W_max_.
3. The convex region, if CUBIC is not in the AIMD-friendly region
and _cwnd_ is greater than _W_max_.
Below, we describe the exact actions taken by CUBIC in each region.
4.3. AIMD-Friendly Region
AIMD TCP performs well in certain types of networks, for example,
under short RTTs and small bandwidths (or small BDPs). In these
networks, CUBIC remains in the AIMD-friendly region to achieve at
least the same throughput as AIMD TCP.
The AIMD-friendly region is designed according to the analysis in
[FHP00], which studies the performance of an AIMD algorithm with an
additive factor of α (segments per _RTT_) and a multiplicative factor
of β, denoted by AIMD(α, β). _p_ is the packet loss rate.
Specifically, the average congestion window size of AIMD(α, β) can be
calculated using Figure 3.
_______________
/ α * (1 + β)
AVG_AIMD(α, β) = | / ---------------
|/ 2 * (1 - β) * p
Figure 3
Xu, et al. Expires 27 January 2022 [Page 11]
Internet-Draft CUBIC July 2021
By the same analysis, to achieve the same average window size as AIMD
TCP that uses AIMD(1, 0.5), α must be equal to,
1 - β
3 * -----
1 + β
Thus, CUBIC uses Figure 4 to estimate the window size _W_est_ in the
AIMD-friendly region with
1 - β
cubic
α = 3 * ----------
cubic 1 + β
cubic
which achieves the same average window size as AIMD TCP. When
receiving an ACK in congestion avoidance (where _cwnd_ could be
greater than or less than _W_max_), CUBIC checks whether W_cubic(_t_)
is less than _W_est_. If so, CUBIC is in the AIMD-friendly region and
_cwnd_ SHOULD be set to _W_est_ at each reception of an ACK.
_W_est_ is set equal to _cwnd_start_ at the start of the congestion
avoidance stage. After that, on every ACK, _W_est_ is updated using
Figure 4. Note that this equation is for a connection where
Appropriate Byte Counting (ABC) [RFC3465] is disabled. For a
connection with ABC enabled, this equation SHOULD be adjusted by
using the number of acknowledged bytes instead of acknowledged
segments. Also note that this equation works for connections with
enabled or disabled Delayed ACKs [RFC5681], as _segments_acked_ will
be different based on the segments actually acknowledged by an ACK.
segments_acked
W = W + α * --------------
est est cubic cwnd
Figure 4
Note that once _W_est_ reaches _W_max_, that is, _W_est_ >= _W_max_,
CUBIC needs to start probing to determine the new value of _W_max_.
At this point, α__cubic_ SHOULD be set to 1 to ensure that CUBIC can
achieve the same congestion window increment as AIMD TCP, which uses
AIMD(1, 0.5).
Xu, et al. Expires 27 January 2022 [Page 12]
Internet-Draft CUBIC July 2021
4.4. Concave Region
When receiving an ACK in congestion avoidance, if CUBIC is not in the
AIMD-friendly region and _cwnd_ is less than _W_max_, then CUBIC is
in the concave region. In this region, _cwnd_ MUST be incremented by
target - cwnd
-------------
cwnd
for each received ACK, where _target_ is calculated as described in
Section 4.2.
4.5. Convex Region
When receiving an ACK in congestion avoidance, if CUBIC is not in the
AIMD-friendly region and _cwnd_ is larger than or equal to _W_max_,
then CUBIC is in the convex region.
The convex region indicates that the network conditions might have
changed since the last congestion event, possibly implying more
available bandwidth after some flow departures. Since the Internet
is highly asynchronous, some amount of perturbation is always
possible without causing a major change in available bandwidth.
Unless it is overridden by the AIMD window increase, CUBIC is very
careful in this region. The convex profile aims to increase the
window very slowly at the beginning when _cwnd_ is around _W_max_ and
then gradually increases its rate of increase. We also call this
region the "maximum probing phase", since CUBIC is searching for a
new _W_max_. In this region, _cwnd_ MUST be incremented by
target - cwnd
-------------
cwnd
for each received ACK, where _target_ is calculated as described in
Section 4.2.
4.6. Multiplicative Decrease
When a congestion event is detected by mechanisms described in
Section 3.1, CUBIC updates _W_max_ and reduces _cwnd_ and _ssthresh_
immediately as described below. An implementation MAY set a smaller
_ssthresh_ than suggested below to accommodate rate-limited
applications as described in [RFC7661]. For both packet loss and
congestion detection through ECN, the sender MAY employ a Fast
Recovery algorithm to gradually adjust the congestion window to its
Xu, et al. Expires 27 January 2022 [Page 13]
Internet-Draft CUBIC July 2021
new reduced _ssthresh_ value. The parameter β__cubic_ SHOULD be set
to 0.7.
ssthresh = cwnd * β // new slow-start threshold
cubic
ssthresh = max(ssthresh, 2) // threshold is at least 2 MSS
// window reduction
cwnd = ssthresh
A side effect of setting β__cubic_ to a value bigger than 0.5 is
slower convergence. We believe that while a more adaptive setting of
β__cubic_ could result in faster convergence, it will make the
analysis of CUBIC much harder.
4.7. Fast Convergence
To improve convergence speed, CUBIC uses a heuristic. When a new
flow joins the network, existing flows need to give up some of their
bandwidth to allow the new flow some room for growth, if the existing
flows have been using all the network bandwidth. To speed up this
bandwidth release by existing flows, the following "Fast Convergence"
mechanism SHOULD be implemented.
With Fast Convergence, when a congestion event occurs, we update
_W_max_ as follows, before the window reduction as described in
Section 4.6.
/
| 1 + β
| cubic if cwnd < W and fast convergence is enabled,
|cwnd * ---------- max
| 2
W = <
max | further reduce W
| max
|
| otherwise, remember cwnd before reduction
\cwnd
Xu, et al. Expires 27 January 2022 [Page 14]
Internet-Draft CUBIC July 2021
At a congestion event, if the current _cwnd_ is less than _W_max_,
this indicates that the saturation point experienced by this flow is
getting reduced because of a change in available bandwidth. Then we
allow this flow to release more bandwidth by reducing _W_max_
further. This action effectively lengthens the time for this flow to
increase its congestion window, because the reduced _W_max_ forces
the flow to plateau earlier. This allows more time for the new flow
to catch up to its congestion window size.
Fast Convergence is designed for network environments with multiple
CUBIC flows. In network environments with only a single CUBIC flow
and without any other traffic, Fast Convergence SHOULD be disabled.
4.8. Timeout
In case of a timeout, CUBIC follows AIMD TCP to reduce _cwnd_
[RFC5681], but sets _ssthresh_ using β__cubic_ (same as in
Section 4.6) in a way that is different from AIMD TCP [RFC5681].
During the first congestion avoidance stage after a timeout, CUBIC
increases its congestion window size using Figure 1, where _t_ is the
elapsed time since the beginning of the current congestion avoidance,
_K_ is set to 0, and _W_max_ is set to the congestion window size at
the beginning of the current congestion avoidance stage. In
addition, for the AIMD-friendly region, _W_est_ SHOULD be set to the
congestion window size at the beginning of the current congestion
avoidance.
4.9. Spurious Congestion Events
In cases where CUBIC reduces its congestion window in response to
having detected packet loss via duplicate ACKs or timeouts, there is
a possibility that the missing ACK would arrive after the congestion
window reduction and a corresponding packet retransmission. For
example, packet reordering could trigger this behavior. A high
degree of packet reordering could cause multiple congestion window
reduction events, where spurious losses are incorrectly interpreted
as congestion signals, thus degrading CUBIC's performance
significantly.
When there is a congestion event, a CUBIC implementation SHOULD save
the current value of the following variables before the congestion
window reduction.
Xu, et al. Expires 27 January 2022 [Page 15]
Internet-Draft CUBIC July 2021
prior_cwnd = cwnd
prior_ssthresh = ssthresh
prior_W = W
max max
prior_K = K
prior_epoch = epoch
start start
prior_W_{est} = W
est
CUBIC MAY implement an algorithm to detect spurious retransmissions,
such as DSACK [RFC3708], Forward RTO-Recovery [RFC5682] or Eifel
[RFC3522]. Once a spurious congestion event is detected, CUBIC
SHOULD restore the original values of above-mentioned variables as
follows if the current _cwnd_ is lower than _prior_cwnd_. Restoring
the original values ensures that CUBIC's performance is similar to
what it would be without spurious losses.
\
cwnd = prior_cwnd |
|
ssthresh = prior_ssthresh |
|
W = prior_W |
max max |
>if cwnd < prior_cwnd
K = prior_K |
|
epoch = prior_epoch |
start start|
|
W = prior_W |
est est /
In rare cases, when the detection happens long after a spurious loss
event and the current _cwnd_ is already higher than _prior_cwnd_,
CUBIC SHOULD continue to use the current and the most recent values
of these variables.
Xu, et al. Expires 27 January 2022 [Page 16]
Internet-Draft CUBIC July 2021
4.10. Slow Start
CUBIC MUST employ a slow-start algorithm, when _cwnd_ is no more than
_ssthresh_. Among the slow-start algorithms, CUBIC MAY choose the
AIMD TCP slow start [RFC5681] in general networks, or the limited
slow start [RFC3742] or hybrid slow start [HR08] for fast and long-
distance networks.
When CUBIC uses hybrid slow start [HR08], it may exit the first slow
start without incurring any packet loss and thus _W_max_ is
undefined. In this special case, CUBIC switches to congestion
avoidance and increases its congestion window size using Figure 1,
where _t_ is the elapsed time since the beginning of the current
congestion avoidance, _K_ is set to 0, and _W_max_ is set to the
congestion window size at the beginning of the current congestion
avoidance stage.
5. Discussion
In this section, we further discuss the safety features of CUBIC
following the guidelines specified in [RFC5033].
With a deterministic loss model where the number of packets between
two successive packet losses is always _1/p_, CUBIC always operates
with the concave window profile, which greatly simplifies the
performance analysis of CUBIC. The average window size of CUBIC can
be obtained by the following function:
________________ ____
/C * (3 + β ) 3 / 4
4 / cubic |/ RTT
AVG_W = | / ---------------- * -------
cubic | / 4 * (1 - β ) __
|/ cubic 3 / 4
|/ p
Figure 5
With β__cubic_ set to 0.7, the above formula reduces to:
____
_______ 3 / 4
4 /C * 3.7 |/ RTT
AVG_W = | / ------- * -------
cubic |/ 1.2 __
3 / 4
|/ p
Xu, et al. Expires 27 January 2022 [Page 17]
Internet-Draft CUBIC July 2021
Figure 6
We will determine the value of _C_ in the following subsection using
Figure 6.
5.1. Fairness to AIMD TCP
In environments where AIMD TCP is able to make reasonable use of the
available bandwidth, CUBIC does not significantly change this state.
AIMD TCP performs well in the following two types of networks:
1. networks with a small bandwidth-delay product (BDP)
2. networks with a short RTTs, but not necessarily a small BDP
CUBIC is designed to behave very similarly to AIMD TCP in the above
two types of networks. The following two tables show the average
window sizes of AIMD TCP, HSTCP, and CUBIC. The average window sizes
of AIMD TCP and HSTCP are from [RFC3649]. The average window size of
CUBIC is calculated using Figure 6 and the CUBIC AIMD-friendly region
for three different values of _C_.
+=============+=======+========+================+=========+========+
| Loss Rate P | AIMD | HSTCP | CUBIC (C=0.04) | CUBIC | CUBIC |
| | | | | (C=0.4) | (C=4) |
+=============+=======+========+================+=========+========+
| 1.0e-02 | 12 | 12 | 12 | 12 | 12 |
+-------------+-------+--------+----------------+---------+--------+
| 1.0e-03 | 38 | 38 | 38 | 38 | 59 |
+-------------+-------+--------+----------------+---------+--------+
| 1.0e-04 | 120 | 263 | 120 | 187 | 333 |
+-------------+-------+--------+----------------+---------+--------+
| 1.0e-05 | 379 | 1795 | 593 | 1054 | 1874 |
+-------------+-------+--------+----------------+---------+--------+
| 1.0e-06 | 1200 | 12280 | 3332 | 5926 | 10538 |
+-------------+-------+--------+----------------+---------+--------+
| 1.0e-07 | 3795 | 83981 | 18740 | 33325 | 59261 |
+-------------+-------+--------+----------------+---------+--------+
| 1.0e-08 | 12000 | 574356 | 105383 | 187400 | 333250 |
+-------------+-------+--------+----------------+---------+--------+
Table 1: AIMD TCP, HSTCP, and CUBIC with RTT = 0.1 seconds
Table 1 describes the response function of AIMD TCP, HSTCP, and CUBIC
in networks with _RTT_ = 0.1 seconds. The average window size is in
MSS-sized segments.
Xu, et al. Expires 27 January 2022 [Page 18]
Internet-Draft CUBIC July 2021
+=============+=======+========+================+=========+=======+
| Loss Rate P | AIMD | HSTCP | CUBIC (C=0.04) | CUBIC | CUBIC |
| | | | | (C=0.4) | (C=4) |
+=============+=======+========+================+=========+=======+
| 1.0e-02 | 12 | 12 | 12 | 12 | 12 |
+-------------+-------+--------+----------------+---------+-------+
| 1.0e-03 | 38 | 38 | 38 | 38 | 38 |
+-------------+-------+--------+----------------+---------+-------+
| 1.0e-04 | 120 | 263 | 120 | 120 | 120 |
+-------------+-------+--------+----------------+---------+-------+
| 1.0e-05 | 379 | 1795 | 379 | 379 | 379 |
+-------------+-------+--------+----------------+---------+-------+
| 1.0e-06 | 1200 | 12280 | 1200 | 1200 | 1874 |
+-------------+-------+--------+----------------+---------+-------+
| 1.0e-07 | 3795 | 83981 | 3795 | 5926 | 10538 |
+-------------+-------+--------+----------------+---------+-------+
| 1.0e-08 | 12000 | 574356 | 18740 | 33325 | 59261 |
+-------------+-------+--------+----------------+---------+-------+
Table 2: AIMD TCP, HSTCP, and CUBIC with RTT = 0.01 seconds
Table 2 describes the response function of AIMD TCP, HSTCP, and CUBIC
in networks with _RTT_ = 0.01 seconds. The average window size is in
MSS-sized segments.
Both tables show that CUBIC with any of these three _C_ values is
more friendly to AIMD TCP than HSTCP, especially in networks with a
short _RTT_ where AIMD TCP performs reasonably well. For example, in
a network with _RTT_ = 0.01 seconds and p=10^-6, AIMD TCP has an
average window of 1200 packets. If the packet size is 1500 bytes,
then AIMD TCP can achieve an average rate of 1.44 Gbps. In this
case, CUBIC with _C_=0.04 or _C_=0.4 achieves exactly the same rate
as AIMD TCP, whereas HSTCP is about ten times more aggressive than
AIMD TCP.
We can see that _C_ determines the aggressiveness of CUBIC in
competing with other congestion control algorithms for bandwidth.
CUBIC is more friendly to AIMD TCP, if the value of _C_ is lower.
However, we do not recommend setting _C_ to a very low value like
0.04, since CUBIC with a low _C_ cannot efficiently use the bandwidth
in fast and long-distance networks. Based on these observations and
extensive deployment experience, we find _C_=0.4 gives a good balance
between AIMD- friendliness and aggressiveness of window increase.
Therefore, _C_ SHOULD be set to 0.4. With _C_ set to 0.4, Figure 6
is reduced to:
Xu, et al. Expires 27 January 2022 [Page 19]
Internet-Draft CUBIC July 2021
____
3 / 4
|/ RTT
AVG_W = 1.054 * -------
cubic __
3 / 4
|/ p
Figure 7
Figure 7 is then used in the next subsection to show the scalability
of CUBIC.
5.2. Using Spare Capacity
CUBIC uses a more aggressive window increase function than AIMD TCP
for fast and long-distance networks.
The following table shows that to achieve the 10 Gbps rate, AIMD TCP
requires a packet loss rate of 2.0e-10, while CUBIC requires a packet
loss rate of 2.9e-8.
+===================+===========+=========+=========+=========+
| Throughput (Mbps) | Average W | AIMD P | HSTCP P | CUBIC P |
+===================+===========+=========+=========+=========+
| 1 | 8.3 | 2.0e-2 | 2.0e-2 | 2.0e-2 |
+-------------------+-----------+---------+---------+---------+
| 10 | 83.3 | 2.0e-4 | 3.9e-4 | 2.9e-4 |
+-------------------+-----------+---------+---------+---------+
| 100 | 833.3 | 2.0e-6 | 2.5e-5 | 1.4e-5 |
+-------------------+-----------+---------+---------+---------+
| 1000 | 8333.3 | 2.0e-8 | 1.5e-6 | 6.3e-7 |
+-------------------+-----------+---------+---------+---------+
| 10000 | 83333.3 | 2.0e-10 | 1.0e-7 | 2.9e-8 |
+-------------------+-----------+---------+---------+---------+
Table 3: Required packet loss rate for AIMD TCP, HSTCP, and
CUBIC to achieve a certain throughput
Table 3 describes the required packet loss rate for AIMD TCP, HSTCP,
and CUBIC to achieve a certain throughput. We use 1500-byte packets
and an _RTT_ of 0.1 seconds.
Our test results in [HKLRX06] indicate that CUBIC uses the spare
bandwidth left unused by existing AIMD TCP flows in the same
bottleneck link without taking away much bandwidth from the existing
flows.
Xu, et al. Expires 27 January 2022 [Page 20]
Internet-Draft CUBIC July 2021
5.3. Difficult Environments
CUBIC is designed to remedy the poor performance of AIMD TCP in fast
and long-distance networks.
5.4. Investigating a Range of Environments
There is decade-long deployment experience with CUBIC on the
Internet. CUBIC has also been extensively studied by using both NS-2
simulation and testbed experiments, covering a wide range of network
environments. More information can be found in [HKLRX06].
Same as AIMD TCP, CUBIC is a loss-based congestion control algorithm.
Because CUBIC is designed to be more aggressive (due to a faster
window increase function and bigger multiplicative decrease factor)
than AIMD TCP in fast and long-distance networks, it can fill large
drop-tail buffers more quickly than AIMD TCP and increases the risk
of a standing queue [RFC8511]. In this case, proper queue sizing and
management [RFC7567] could be used to reduce the packet queuing
delay.
5.5. Protection against Congestion Collapse
With regard to the potential of causing congestion collapse, CUBIC
behaves like AIMD TCP, since CUBIC modifies only the window
adjustment algorithm of AIMD TCP. Thus, it does not modify the ACK
clocking and timeout behaviors of AIMD TCP.
5.6. Fairness within the Alternative Congestion Control Algorithm
CUBIC ensures convergence of competing CUBIC flows with the same RTT
in the same bottleneck links to an equal throughput. When competing
flows have different RTT values, their throughput ratio is linearly
proportional to the inverse of their RTT ratios. This is true
independently of the level of statistical multiplexing on the link.
5.7. Performance with Misbehaving Nodes and Outside Attackers
This is not considered in the current CUBIC design.
5.8. Behavior for Application-Limited Flows
CUBIC does not increase its congestion window size if a flow is
currently limited by the application instead of the congestion
window. In case of long periods during which _cwnd_ has not been
updated due to such an application limit, such as idle periods, _t_
in Figure 1 MUST NOT include these periods; otherwise, W_cubic(_t_)
might be very high after restarting from these periods.
Xu, et al. Expires 27 January 2022 [Page 21]
Internet-Draft CUBIC July 2021
5.9. Responses to Sudden or Transient Events
If there is a sudden congestion, a routing change, or a mobility
event, CUBIC behaves the same as AIMD TCP.
5.10. Incremental Deployment
CUBIC requires only changes to TCP senders, and it does not require
any changes at TCP receivers. That is, a CUBIC sender works
correctly with the AIMD TCP receivers. In addition, CUBIC does not
require any changes to routers and does not require any assistance
from routers.
6. Security Considerations
CUBIC makes no changes to the underlying security of TCP. More
information about TCP security concerns can be found in [RFC5681].
7. IANA Considerations
This document does not require any IANA actions.
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
.
[RFC3168] Ramakrishnan, K., Floyd, S., and D. Black, "The Addition
of Explicit Congestion Notification (ECN) to IP",
RFC 3168, DOI 10.17487/RFC3168, September 2001,
.
[RFC5033] Floyd, S. and M. Allman, "Specifying New Congestion
Control Algorithms", BCP 133, RFC 5033,
DOI 10.17487/RFC5033, August 2007,
.
[RFC5348] Floyd, S., Handley, M., Padhye, J., and J. Widmer, "TCP
Friendly Rate Control (TFRC): Protocol Specification",
RFC 5348, DOI 10.17487/RFC5348, September 2008,
.
Xu, et al. Expires 27 January 2022 [Page 22]
Internet-Draft CUBIC July 2021
[RFC5681] Allman, M., Paxson, V., and E. Blanton, "TCP Congestion
Control", RFC 5681, DOI 10.17487/RFC5681, September 2009,
.
[RFC6298] Paxson, V., Allman, M., Chu, J., and M. Sargent,
"Computing TCP's Retransmission Timer", RFC 6298,
DOI 10.17487/RFC6298, June 2011,
.
[RFC6582] Henderson, T., Floyd, S., Gurtov, A., and Y. Nishida, "The
NewReno Modification to TCP's Fast Recovery Algorithm",
RFC 6582, DOI 10.17487/RFC6582, April 2012,
.
[RFC6675] Blanton, E., Allman, M., Wang, L., Jarvinen, I., Kojo, M.,
and Y. Nishida, "A Conservative Loss Recovery Algorithm
Based on Selective Acknowledgment (SACK) for TCP",
RFC 6675, DOI 10.17487/RFC6675, August 2012,
.
[RFC7567] Baker, F., Ed. and G. Fairhurst, Ed., "IETF
Recommendations Regarding Active Queue Management",
BCP 197, RFC 7567, DOI 10.17487/RFC7567, July 2015,
.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, .
[RFC8985] Cheng, Y., Cardwell, N., Dukkipati, N., and P. Jha, "The
RACK-TLP Loss Detection Algorithm for TCP", RFC 8985,
DOI 10.17487/RFC8985, February 2021,
.
[RFC9002] Iyengar, J., Ed. and I. Swett, Ed., "QUIC Loss Detection
and Congestion Control", RFC 9002, DOI 10.17487/RFC9002,
May 2021, .
8.2. Informative References
[CEHRX07] Cai, H., Eun, D., Ha, S., Rhee, I., and L. Xu, "Stochastic
Ordering for Internet Congestion Control and its
Applications", IEEE INFOCOM 2007 - 26th IEEE International
Conference on Computer Communications,
DOI 10.1109/infcom.2007.111, 2007,
.
Xu, et al. Expires 27 January 2022 [Page 23]
Internet-Draft CUBIC July 2021
[FHP00] Floyd, S., Handley, M., and J. Padhye, "A Comparison of
Equation-Based and AIMD Congestion Control", May 2000,
.
[GV02] Gorinsky, S. and H. Vin, "Extended Analysis of Binary
Adjustment Algorithms", Technical Report TR2002-29,
Department of Computer Sciences, The University of
Texas at Austin, 11 August 2002,
.
[HKLRX06] Ha, S., Kim, Y., Le, L., Rhee, I., and L. Xu, "A Step
toward Realistic Performance Evaluation of High-Speed TCP
Variants", International Workshop on Protocols for Fast
Long-Distance Networks, February 2006,
.
[HR08] Ha, S. and I. Rhee, "Hybrid Slow Start for High-Bandwidth
and Long-Distance Networks", International Workshop
on Protocols for Fast Long-Distance Networks, March 2008,
.
[HRX08] Ha, S., Rhee, I., and L. Xu, "CUBIC: a new TCP-friendly
high-speed TCP variant", ACM SIGOPS Operating Systems
Review Vol. 42, pp. 64-74, DOI 10.1145/1400097.1400105,
July 2008, .
[K03] Kelly, T., "Scalable TCP: improving performance in
highspeed wide area networks", ACM SIGCOMM Computer
Communication Review Vol. 33, pp. 83-91,
DOI 10.1145/956981.956989, April 2003,
.
[RFC3465] Allman, M., "TCP Congestion Control with Appropriate Byte
Counting (ABC)", RFC 3465, DOI 10.17487/RFC3465, February
2003, .
[RFC3522] Ludwig, R. and M. Meyer, "The Eifel Detection Algorithm
for TCP", RFC 3522, DOI 10.17487/RFC3522, April 2003,
.
[RFC3649] Floyd, S., "HighSpeed TCP for Large Congestion Windows",
RFC 3649, DOI 10.17487/RFC3649, December 2003,
.
[RFC3708] Blanton, E. and M. Allman, "Using TCP Duplicate Selective
Acknowledgement (DSACKs) and Stream Control Transmission
Protocol (SCTP) Duplicate Transmission Sequence Numbers
Xu, et al. Expires 27 January 2022 [Page 24]
Internet-Draft CUBIC July 2021
(TSNs) to Detect Spurious Retransmissions", RFC 3708,
DOI 10.17487/RFC3708, February 2004,
.
[RFC3742] Floyd, S., "Limited Slow-Start for TCP with Large
Congestion Windows", RFC 3742, DOI 10.17487/RFC3742, March
2004, .
[RFC4960] Stewart, R., Ed., "Stream Control Transmission Protocol",
RFC 4960, DOI 10.17487/RFC4960, September 2007,
.
[RFC5682] Sarolahti, P., Kojo, M., Yamamoto, K., and M. Hata,
"Forward RTO-Recovery (F-RTO): An Algorithm for Detecting
Spurious Retransmission Timeouts with TCP", RFC 5682,
DOI 10.17487/RFC5682, September 2009,
.
[RFC7661] Fairhurst, G., Sathiaseelan, A., and R. Secchi, "Updating
TCP to Support Rate-Limited Traffic", RFC 7661,
DOI 10.17487/RFC7661, October 2015,
.
[RFC8312] Rhee, I., Xu, L., Ha, S., Zimmermann, A., Eggert, L., and
R. Scheffenegger, "CUBIC for Fast Long-Distance Networks",
RFC 8312, DOI 10.17487/RFC8312, February 2018,
.
[RFC8511] Khademi, N., Welzl, M., Armitage, G., and G. Fairhurst,
"TCP Alternative Backoff with ECN (ABE)", RFC 8511,
DOI 10.17487/RFC8511, December 2018,
.
[RFC9000] Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
Multiplexed and Secure Transport", RFC 9000,
DOI 10.17487/RFC9000, May 2021,
.
[SXEZ19] Sun, W., Xu, L., Elbaum, S., and D. Zhao, "Model-Agnostic
and Efficient Exploration of Numerical State Space of
Real-World TCP Congestion Control Implementations", USENIX
NSDI 2019, February 2019,
.
[XHR04] Xu, L., Harfoush, K., and I. Rhee, "Binary Increase
Congestion Control (BIC) for Fast Long-Distance Networks",
IEEE INFOCOM 2004, DOI 10.1109/infcom.2004.1354672, March
2004, .
Xu, et al. Expires 27 January 2022 [Page 25]
Internet-Draft CUBIC July 2021
Appendix A. Acknowledgments
Richard Scheffenegger and Alexander Zimmermann originally co-authored
[RFC8312].
Appendix B. Evolution of CUBIC
B.1. Since draft-ietf-tcpm-rfc8312bis-02
* Decription of packet loss rate _p_ (#65
(https://github.com/NTAP/rfc8312bis/issues/65))
* Clarification of TCP Friendly Equation for ABC and Delayed ACK
(#66 (https://github.com/NTAP/rfc8312bis/issues/66))
* add applicability to QUIC and SCTP (#61
(https://github.com/NTAP/rfc8312bis/issues/61))
* clarity on setting alpha__aimd_ to 1 (#68
(https://github.com/NTAP/rfc8312bis/issues/68))
* introduce alpha__cubic_ (#64 (https://github.com/NTAP/rfc8312bis/
issues/64))
* clarify _cwnd_ growth in convex region (#69
(https://github.com/NTAP/rfc8312bis/issues/69))
* add guidance for using bytes and mention that segments count is
decimal (#67 (https://github.com/NTAP/rfc8312bis/issues/67))
* add loss events detected by RACK and QUIC loss detection (#62
(https://github.com/NTAP/rfc8312bis/issues/62))
B.2. Since draft-ietf-tcpm-rfc8312bis-01
* address Michael Scharf's editorial suggestions. (#59
(https://github.com/NTAP/rfc8312bis/issues/59))
* add "Note to the RFC Editor" about removing underscores
B.3. Since draft-ietf-tcpm-rfc8312bis-00
* use updated xml2rfc with better text rendering of subscripts
B.4. Since draft-eggert-tcpm-rfc8312bis-03
* fix spelling nits
Xu, et al. Expires 27 January 2022 [Page 26]
Internet-Draft CUBIC July 2021
* rename to draft-ietf
* define _W_max_ more clearly
B.5. Since draft-eggert-tcpm-rfc8312bis-02
* add definition for segments_acked and alpha__aimd_. (#47
(https://github.com/NTAP/rfc8312bis/issues/47))
* fix a mistake in _W_max_ calculation in the fast convergence
section. (#51 (https://github.com/NTAP/rfc8312bis/issues/51))
* clarity on setting _ssthresh_ and _cwnd_start_ during
multiplicative decrease. (#53 (https://github.com/NTAP/rfc8312bis/
issues/53))
B.6. Since draft-eggert-tcpm-rfc8312bis-01
* rename TCP-Friendly to AIMD-Friendly and rename Standard TCP to
AIMD TCP to avoid confusion as CUBIC has been widely used on the
Internet. (#38 (https://github.com/NTAP/rfc8312bis/issues/38))
* change introductory text to reflect the significant broader
deployment of CUBIC on the Internet. (#39
(https://github.com/NTAP/rfc8312bis/issues/39))
* rephrase introduction to avoid referring to variables that have
not been defined yet.
B.7. Since draft-eggert-tcpm-rfc8312bis-00
* acknowledge former co-authors (#15
(https://github.com/NTAP/rfc8312bis/issues/15))
* prevent _cwnd_ from becoming less than two (#7
(https://github.com/NTAP/rfc8312bis/issues/7))
* add list of variables and constants (#5
(https://github.com/NTAP/rfc8312bis/issues/5), #6
(https://github.com/NTAP/rfc8312bis/issues/6))
* update _K_'s definition and add bounds for CUBIC _target_ _cwnd_
[SXEZ19] (#1 (https://github.com/NTAP/rfc8312bis/issues/1), #14
(https://github.com/NTAP/rfc8312bis/issues/14))
* update _W_est_ to use AIMD approach (#20
(https://github.com/NTAP/rfc8312bis/issues/20))
Xu, et al. Expires 27 January 2022 [Page 27]
Internet-Draft CUBIC July 2021
* set alpha__aimd_ to 1 once _W_est_ reaches _W_max_ (#2
(https://github.com/NTAP/rfc8312bis/issues/2))
* add Vidhi as co-author (#17 (https://github.com/NTAP/rfc8312bis/
issues/17))
* note for Fast Recovery during _cwnd_ decrease due to congestion
event (#11 (https://github.com/NTAP/rfc8312bis/issues/11))
* add section for spurious congestion events (#23
(https://github.com/NTAP/rfc8312bis/issues/23))
* initialize _W_est_ after timeout and remove variable
_W_(last_max)_ (#28 (https://github.com/NTAP/rfc8312bis/
issues/28))
B.8. Since RFC8312
* converted to Markdown and xml2rfc v3
* updated references (as part of the conversion)
* updated author information
* various formatting changes
* move to Standards Track
B.9. Since the Original Paper
CUBIC has gone through a few changes since the initial release
[HRX08] of its algorithm and implementation. Below we highlight the
differences between its original paper and [RFC8312].
* The original paper [HRX08] includes the pseudocode of CUBIC
implementation using Linux's pluggable congestion control
framework, which excludes system-specific optimizations. The
simplified pseudocode might be a good source to start with and
understand CUBIC.
* [HRX08] also includes experimental results showing its performance
and fairness.
Xu, et al. Expires 27 January 2022 [Page 28]
Internet-Draft CUBIC July 2021
* The definition of beta__cubic_ constant was changed in [RFC8312].
For example, beta__cubic_ in the original paper was the window
decrease constant while [RFC8312] changed it to CUBIC
multiplication decrease factor. With this change, the current
congestion window size after a congestion event in [RFC8312] was
beta__cubic_ * _W_max_ while it was (1-beta__cubic_) * _W_max_ in
the original paper.
* Its pseudocode used _W_(last_max)_ while [RFC8312] used _W_max_.
* Its AIMD-friendly window was _W_tcp_ while [RFC8312] used _W_est_.
Authors' Addresses
Lisong Xu
University of Nebraska-Lincoln
Department of Computer Science and Engineering
Lincoln, NE 68588-0115
United States of America
Email: xu@unl.edu
URI: https://cse.unl.edu/~xu/
Sangtae Ha
University of Colorado at Boulder
Department of Computer Science
Boulder, CO 80309-0430
United States of America
Email: sangtae.ha@colorado.edu
URI: https://netstech.org/sangtaeha/
Injong Rhee
Bowery Farming
151 W 26TH Street, 12TH Floor
New York, NY 10001
United States of America
Email: injongrhee@gmail.com
Xu, et al. Expires 27 January 2022 [Page 29]
Internet-Draft CUBIC July 2021
Vidhi Goel
Apple Inc.
One Apple Park Way
Cupertino, California 95014
United States of America
Email: vidhi_goel@apple.com
Lars Eggert (editor)
NetApp
Stenbergintie 12 B
FI-02700 Kauniainen
Finland
Email: lars@eggert.org
URI: https://eggert.org/
Xu, et al. Expires 27 January 2022 [Page 30]