Storage Maintenance (storm) Working Group Michael Ko Internet Draft Huawei Symantec Intended status: Proposed Standard David L. Black Expires: June 2012 EMC December 21, 2011 IANA Registries for the RDDP (Remote Direct Data Placement) Protocols draft-ietf-storm-rddp-registries-01.txt Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on June 21, 2012. Abstract The original RFCs that specified the RDDP protocol suite did not create IANA registries for RDDP error codes, operation codes and function codes. Extensions to the RDDP protocols now require these registries to be created. This memo creates the RDDP registries, populates them with values defined in the original RDDP RFCs, and provides guidance to IANA for future assignment of code points within these registries. Ko and Black Expires June 2012 [Page 1] Internet-Draft IANA Considerations for RDDP October 2011 Table of Contents 1. Introduction ................................................2 1.1 Conventions .................................................2 2. Security Considerations .....................................2 3. IANA Considerations .........................................2 3.1 RDMAP Errors ................................................3 3.2 DDP Errors ..................................................5 3.3 MPA Errors ..................................................7 3.4 RDMAP Message Operation Codes ...............................8 3.5 SCTP Function Codes for DDP Stream Session Control ..........9 4. Normative References .......................................10 5. Informative References .....................................10 6. Acknowledgments ............................................10 1. Introduction The original RFCs that specified the RDDP protocol suite [RFC5040][RFC5041][RFC5043][RFC5044] did not create IANA registries. Extensions to the RDDP protocols [MPA-PEER][RDMAP-EXT] now requires creation and use of IANA registries. This memo creates the RDDP- related IANA registries, specifies their initial contents based on the values defined in the original RDDP RFCs, and provides guidance to IANA for future assignments from these registries. 1.1 Conventions The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 2. Security Considerations Since this document is only concerned with creation and IANA management of RDDP registries, it raises no new security issues. 3. IANA Considerations This memo creates the following RDDP registries for IANA to manage: o RDMAP Errors (Section 3.1) o DDP Errors (Section 3.2) o MPA Errors (Section 3.3) o RDMAP Message Operation Codes (Section 3.4) o SCTP Function Codes for DDP Stream Session Control (Section 3.5) Ko and Black Expires June 2012 [Page 2] Internet-Draft IANA Considerations for RDDP October 2011 Each of the following sections specifies a registry, its initial contents and the administration policy in more detail. 3.1 RDMAP Errors Name of the registry: "RDMAP Errors" Namespace details: An RDMAP (Remote Direct Memory Access Protocol) error is a 16 bit field divided into three subfields [RFC5040]: o 4-bit Layer, MUST be 0x0 for RDMAP errors o 4-bit Error Type o 8-bit Error Code The Error Code field is OPTIONAL for this registry, as Error Codes are not used with all RDMAP Error Types. When no numerical Error Code is registered, any 8-bit value MAY be used as the Error Code, as the Layer and Error Type values are sufficient to specify the error. For this reason, if an RDMAP Error Type is registered without an Error Code, IANA MUST NOT add an entry to this registry with an Error Code for the same Error Type. Information that must be provided to assign a new value: An IESG- approved standards-track specification defining the semantics and interoperability requirements of the proposed new value and the fields to be recorded in the registry. Assignment policy: If the requested value is not already assigned, it may be assigned to the requester. Fields to record in the registry: Layer/Error-Type/Error-Code, Error-Type-Name/Error-Code-Name, RFC Reference. The Error-Code and Error-Code-Name are omitted for Error-Types that do not have Error-Codes. When a specific error code is not registered, the registry entry contains the string "ALL" for the Error Code instead of a numerical value, and the Error Code Name is omitted from the registry entry. Initial registry contents: 0x0/0x0/ALL , Local Catastrophic Error, [RFC5040] 0x0/0x1/0x00, Remote Protection Error / Invalid Steering Tag, [RFC5040] 0x0/0x1/0x01, Remote Protection Error / Base or bounds violation, [RFC5040] Ko and Black Expires June 2012 [Page 3] Internet-Draft IANA Considerations for RDDP October 2011 0x0/0x1/0x02, Remote Protection Error / Access rights violation, [RFC5040] 0x0/0x1/0x03, Remote Protection Error / Steering Tag not associated with RDMAP Stream, [RFC5040] 0x0/0x1/0x04, Remote Protection Error / Tagged Offset wrap, [RFC5040] 0x0/0x1/0x09, Remote Protection Error / Steering Tag cannot be invalidated, [RFC5040] 0x0/0x1/0xff, Remote Protection Error / Unspecified Error, [RFC5040] 0x0/0x2/0x05, Remote Operation Error / Invalid RDMAP version, [RFC5040] 0x0/0x2/0x06, Remote Operation Error / Unexpected OpCode, [RFC5040] 0x0/0x2/0x07, Remote Operation Error / Catastrophic error, localized to RDMAP Stream, [RFC5040] 0x0/0x2/0x08, Remote Operation Error / Catastrophic error, global, [RFC5040] 0x0/0x2/0x09, Remote Operation Error / Steering Tag cannot be Invalidated, [RFC5040] 0x0/0x2/0xff, Remote Operation Error / Unspecified Error, [RFC5040] All combinations not listed above that combine 0x0 as the Layer with an Error Type and Error Code are Unassigned and available to IANA for assignment. Allocation Policy: Standards Action ([RFC5226]) Ko and Black Expires June 2012 [Page 4] Internet-Draft IANA Considerations for RDDP October 2011 3.2 DDP Errors Name of the registry: "DDP Errors" Namespace details: A DDP (Direct Data Placement) error is a 16 bit field divided into three subfields [RFC5041]: o 4-bit Layer, MUST be 0x1 for DDP errors o 4-bit Error Type o 8-bit Error Code The Error Code field is REQUIRED for this registry, except for the registry entry that reserves a set of errors for use by the Lower Layer Protocol. Information that must be provided to assign a new value: An IESG- approved standards-track specification defining the semantics and interoperability requirements of the proposed new value and the fields to be recorded in the registry. Assignment policy: If the requested value is not already assigned, it may be assigned to the requester. Fields to record in the registry: Layer/Error-Type/Error-Code, Error-Type-Name/Error-Code-Name, RFC Reference. The last registry entry in the initial registry contents below reserves a set of errors for use by the Lower Layer Protocol. That entry uses "ALL" for the Error Code and omits the Error Code Name. For all other entries in this registry, the string "ALL" MUST NOT be used for the Error Code, and an Error Code Name MUST be part of the registry entry. Initial registry contents: 0x1/0x0/0x00, Local Catastrophic, [RFC5041] 0x1/0x1/0x00, Tagged Buffer Error / Invalid Steering Tag, [RFC5041] 0x1/0x1/0x01, Tagged Buffer Error / Base or bounds violation, [RFC5041] 0x1/0x1/0x02, Tagged Buffer Error / Steering Tag not associated with DDP Stream, [RFC5041] 0x1/0x1/0x03, Tagged Buffer Error / Tagged Offset wrap, [RFC5041] 0x1/0x1/0x04, Tagged Buffer Error / Invalid DDP version, [RFC5041] Ko and Black Expires June 2012 [Page 5] Internet-Draft IANA Considerations for RDDP October 2011 0x1/0x2/0x01, Untagged Buffer Error / Invalid Queue Number, [RFC5041] 0x1/0x2/0x02, Untagged Buffer Error / Invalid Message Sequence Number - no buffer available, [RFC5041] 0x1/0x2/0x03, Untagged Buffer Error / Invalid Message Sequence Number - Message Sequence Number range is not valid, [RFC5041] 0x1/0x2/0x04, Untagged Buffer Error / Invalid Message Offset, [RFC5041] 0x1/0x2/0x05, Untagged Buffer Error / DDP Message too long for available buffer, [RFC5041] 0x1/0x2/0x06, Untagged Buffer Error / Invalid DDP version, [RFC5041] 0x1/0x3/ALL , Reserved for use by Lower Layer Protocol, [RFC5041] All combinations not listed above that combine 0x1 as the Layer with an Error Type and Error Code are Unassigned and available to IANA for assignment. Allocation Policy: Standards Action ([RFC5226]) Ko and Black Expires June 2012 [Page 6] Internet-Draft IANA Considerations for RDDP October 2011 3.3 MPA Errors Name of the registry: "MPA Errors" Namespace details: An MPA (Marker PDU Aligned Framing for TCP) error is a 16 bit field divided into three subfields [RFC5044]: o 4-bit Layer, MUST be 0x2 for MPA errors o 4-bit Error Type o 8-bit Error Code The Error Code field is REQUIRED for this registry. Information that must be provided to assign a new value: An IESG- approved standards-track specification defining the semantics and interoperability requirements of the proposed new value and the fields to be recorded in the registry. Assignment policy: If the requested value is not already assigned, it may be assigned to the requester. Fields to record in the registry: Layer/Error-Type/Error-Code, Error-Type-Name/Error-Code-Name, RFC Reference. The string "ALL" MUST NOT be used for the Error Code in this registry, and an Error Code Name is REQUIRED in every entry in this registry. Initial registry contents: 0x2/0x0/0x01, MPA Error / TCP connection closed, terminated, or lost, [RFC5044] 0x2/0x0/0x02, MPA Error / MPA CRC Error, [RFC5044] 0x2/0x0/0x03, MPA Error / MPA Marker and ULPDU Length field mismatch, [RFC5044] 0x2/0x0/0x04, MPA Error / Invalid MPA Request Frame or MPA Response Frame, [RFC5044] All combinations not listed above that combine 0x2 as the Layer with an Error Type and Error Code are Unassigned and available to IANA for assignment. Allocation Policy: Standards Action ([RFC5226]) Ko and Black Expires June 2012 [Page 7] Internet-Draft IANA Considerations for RDDP October 2011 3.4 RDMAP Message Operation Codes Name of the registry: "RDMAP Message Operation Codes" Namespace details: RDMAP Operation Codes are 4-bit values [RFC5040]. Information that must be provided to assign a new value: An IESG- approved standards-track specification defining the semantics and interoperability requirements of the proposed new value and the fields to be recorded in the registry. Assignment policy: If the requested value is not already assigned, it may be assigned to the requester. Fields to record in the registry: RDMAP Message Operation Code, Message Type, RFC Reference Initial registry contents: 0x0, RDMA Write, [RFC5040] 0x1, RDMA Read Request, [RFC5040] 0x2, RDMA Read Response, [RFC5040] 0x3, Send, [RFC5040] 0x4, Send with Invalidate, [RFC5040] 0x5, Send with Solicited Event, [RFC5040] 0x6, Send with Solicited Event and Invalidate, [RFC5040] 0x7, Terminate, [RFC5040] All other values are Unassigned and available to IANA for assignment. Allocation Policy: Standards Action ([RFC5226]) Ko and Black Expires June 2012 [Page 8] Internet-Draft IANA Considerations for RDDP October 2011 3.5 SCTP Function Codes for DDP Stream Session Control Name of the registry: "SCTP Function Codes for DDP Session Control" Namespace details: SCTP (Stream Control Transmission Protocol) function codes for DDP session control are 16-bit values [RFC5043]. Information that must be provided to assign a new value: An IESG- approved standards-track specification defining the semantics and interoperability requirements of the proposed new value and the fields to be recorded in the registry. Assignment policy: If the requested value is not already assigned, it may be assigned to the requester. Fields to record in the registry: SCTP Function Code, SCTP Function Name, RFC Reference Initial registry contents: 0x0001, DDP Stream Session Initiate, [RFC5043] 0x0002, DDP Stream Session Accept, [RFC5043] 0x0003, DDP Stream Session Reject, [RFC5043] 0x0004, DDP Stream Session Terminate, [RFC5043] All other values are Unassigned and available to IANA for assignment. Allocation Policy: Standards Action ([RFC5226]) Ko and Black Expires June 2012 [Page 9] Internet-Draft IANA Considerations for RDDP October 2011 4. Normative References [RFC2119] S. Bradner, "Key Words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC5040] R. Recio et al., "An RDMA Protocol Specification", RFC 5040, October 2007. [RFC5041] H. Shah et al., "Direct Data Placement over Reliable Transports", RFC 5041, October 2007. [RFC5043] C. Bestler et al., "Stream Control Transmission Protocol (SCTP) Direct Data Placement (DDP) Adaptation", RFC 5043, October 2007. [RFC5044] P. Culley et al., "Marker PDU Aligned Framing for TCP Specification", RFC 5044, October 2007. [RFC5226] T. Narten and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", RFC 5226, BCP 26, May 2008. 5. Informative References [MPA-PEER] A. Kanevsky, et al., "Enhanced RDMA Connection Establishment", draft-ietf-storm-mpa-peer-connect-09, work in progress, December 2011. [RDMAP-EXT] H. Shah, et al., "RDMA Protocol Extensions", draft-ietf-storm-rdmap-ext-01, work in progress, July 2011. 6. Acknowledgments IANA's review of a draft version of this document indicated the need for some corrections; the authors thank IANA for that review. Ko and Black Expires June 2012 [Page 10] Internet-Draft IANA Considerations for RDDP October 2011 Author's Address Michael Ko Huawei Symantec 20245 Stevens Creek Blvd. Cupertino, CA 95014, USA Phone: +1-408-510-7465 Email: michael@huaweisymantec.com David L. Black EMC Corporation 176 South St. Hopkinton, MA 01748, USA Phone: +1-508-293-7953 Email: david.black@emc.com Copyright Notice Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/ license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Ko and Black Expires June 2012 [Page 11]