Internet Draft APPC MIB July 18, 1994 Definitions of Managed Objects for APPC July 18, 1994 Michael Allen (editor) IBM Corporation moallen@vnet.ibm.com Zbigniew Kielczewski (editor) Eicon Technology Corporation zbig@eicon.qc.ca William Kwan (editor) CrossComm Corporation kwan@crosscomm.com Status of this Memo This document is an Internet-Draft. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months. Internet-Drafts may be updated, replaced, or obsoleted by other documents at any time. It is not appropriate to use Internet-Drafts as reference material or to cite them other than as a "working draft" or "work in progress". To learn the current status of any Internet-Draft, please check the 1id-abstracts.txt listing contained in the Internet-Drafts Shadow Directories on ds.internic.net, nic.nordu.net, ftp.isi.edu, or munnari.oz.au. Expires December 1994 [Page 1] Internet Draft APPC MIB July 18, 1994 1. Introduction This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines objects for managing the configuration, monitoring and control of network devices with APPC (Advanced Program to Program Communications) capabilities. This memo identifies managed objects for SNA-capable devices with one or more Type 2.1 nodes. These objects are specific for the LU6.2 protocols and supplement the generic SNA objects defined in the SNA NAU MIB module[7]. Many of the tables in this APPC MIB module are extensions of tables described in the SNA NAU MIB module. The SNA terms and overall architecture are documented in [1]. This memo does not specify a standard for the Internet community. Expires December 1994 [Page 2] Internet Draft APPC MIB July 18, 1994 2. The SNMPv2 Network Management Framework The SNMPv2 Network Management Framework consists of four major components. They are: o RFC 1442 [2] which defines the SMI, the mechanisms used for describing and naming objects for the purpose of management. o RFC 1213 [3] defines MIB-II, the core set of managed objects for the Internet suite of protocols. o RFC 1445 [4] which defines the administrative and other architectural aspects of the framework. o RFC 1448 [5] which defines the protocol used for network access to managed objects. The Framework permits new objects to be defined for the purpose of experimentation and evaluation. 2.1. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI (RFC 1442 [2]). In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to refer to the object type. Expires December 1994 [Page 3] Internet Draft APPC MIB July 18, 1994 3. Overview This document identifies the proposed set of objects for managing the configuration, monitoring and controlling devices with APPC capabilities. APPC is the aspect of SNA which supports peer to peer communication. It consists of physical nodes (typically T2.1, but could be 2.0 or 5), which provide the lower layer networking protocols and logical units (LU Type 6.2) which provide the interface for applications to communicate. Local LUs and remote partner LUs connect with each other using sessions. Multiple different sessions can be established between LUs with characteristics defined by Modes. Transaction Programs (TP) are the applications which use the sessions to communicate with each other. Multiple TPs can use the same sessions, but not at the same time. A single usage of a session is called a conversation. While a session can stay active for a long time, a conversation can come up and down based on usage by the TPs. Common Programming Interface - Communication (CPI- C) is a standard API (Application Programming Interface) for APPC that is used by TPs for accessing conversations. Highlights of the management functions supported by the APPC MIB module include the following: o Monitoring of global APPC information. o Activate and deactivate statistics keeping and counting. o Modification of APPC defaults. o Creation and deletion of partner LUs, modes, TPs and CPI-C side information via the RowStatus objects in their respective admin tables. o Monitoring and modification of parameters related to local LU, partner LU, modes, TPs and CPIC side information. o Monitoring of APPC specific session operational parameters. o Monitoring of conversation operational parameters. o Traps for: + No traps defined. Expires December 1994 [Page 4] Internet Draft APPC MIB July 18, 1994 This MIB module does not support: o Activation or deactivation of local LUs. o Activation or deactivation of partner LUs. o Activation or deactivation of conversations. o Activation or deactivation of Transaction Programs. o Activation of sessions. o Deactivation of sessions (supported in SNANAU MIB). 3.1. Applying MIB II to managing APPC devices This section identifies how MIB II objects, specifically the MIB II system group will be used in SNMP-based management of SNA NAUs. The MIB II system group applies to the SNMP Agent. The following object is from the MIB II system group: sysUpTime: clock in the SNMP Agent/proxy-Agent; expressed in TimeTicks (1/100s of a seconds). This MIB module uses the TimeStamp TEXTUAL-CONVENTION which is defined in the SNMPv2 Textual Conventions (RFC 1443 [6]) as "the value of MIB II's sysUpTime object when a specific occurrence happens." The specific occurrences related to APPC management are defined in this MIB module. 3.2. APPC MIB Structure The APPC MIB module contains six groups of objects: o appcGlobal - objects related to global statistics, defaults and controls. o appcLu - objects related to LU6.2 specific local and partner LU, mode definition, monitoring and control. Expires December 1994 [Page 5] Internet Draft APPC MIB July 18, 1994 o appcTp - objects related transaction program definition, monitoring and control. o appcSession - objects related to LU6.2 specific session monitoring. o appcConversation - objects related conversation monitoring. o appcCPIC - objects related related CPI-C side information definition and monitoring. These groups are described below in more detail. The objects related to APPC are generally organized into two types of tables: the Admin and Oper tables. The "Admin" table contains parameters which are used by a Management Station to affect the operation of APPC. Some parameters are used to initialize and configure the APPC service at the next startup, while others can take effect immediately. A Management Station can dynamically define APPC resources (LUs, modes, TPs, CPI-C side information tables) by creating new entries in the Admin table. The "Oper" table is an extension (supplement) of the corresponding Admin table. It contains objects which correspond to the values of parameters currently used by the APPC system. Some of tables also supplements Admin and Oper tables from the SNA NAU MIB module. 3.2.1. appcGlobal group The appcGlobal group consists of the following tables and objects: 1) appcGlobalTable This table contains objects which describe global APPC information for each node. The type of information includes number of active local LUs and number of active sessions. This table supplements the snaNodeOperTable, defined in the SNA NAU MIB Expires December 1994 [Page 6] Internet Draft APPC MIB July 18, 1994 module, as such uses the same index(i.e., snaNodeAdminIndex). However, only entries in the snaNodeOperTable that are nodes which support APPC or LU6.2 protocols, would have a corresponding entry in this table. The rows in this table are created by an Agent as soon as the entry in the snaNodeOperTable becomes 'active'. The entries in this table cannot be modified by a Management Station. 2) appcStatCntlGroup This group of objects controls whether certain statistics and counters (e.g., session and RSCV counters) are maintained by an Agent. These objects are for implementations that wish to provide this level of operational control and is optional. These objects can be generated initially, after startup of SNA service, by the Agent which uses information from the Node configuration file. Subsequent modifications of parameters is possible by a Management station. The modifications to these objects can be saved in the Node configuration file for the next startup (i.e., restart or next initialization) of SNA service, but the mechanism for this function is not defined in this document. 3) appcDefaultTable - This table contains objects which describe default APPC configurations for each node. The type of default information includes mode name, LU, and maximum logical record size. This table supplements the snaNodeAdminTable, defined in the SNA NAU MIB module, and as such uses the same index (i.e., snaNodeAdminIndex). However, only entries in the snaNodeAdminTable that are nodes which support APPC or LU6.2 protocols, would have a corresponding entry in this table. The rows in this table are created by an Agent as soon as the entry in the snaNodeAdminTable becomes 'active'. The entries in this table can be modified by a Management Station. 3.2.2. appcLu group The appcLu group consists of the following tables: 1) appcLluOperTable Expires December 1994 [Page 7] Internet Draft APPC MIB July 18, 1994 This table contains objects which describe specific APPC local LU operational information. The type of information includes maximum number of sessions supported and whether the LU is the Control Point. This table supplements the snaLuOperTable, defined in the SNA NAU MIB module, and as such uses the same set of indices(i.e., snaNodeAdminIndex and snaLuAdminLuIndex). However, only entries in the snaLuOperTable that support APPC or LU6.2 protocols, would have a corresponding entry in this table. The rows in this table are created by an Agent as soon as the entry in the snaLuOperTable becomes 'active'. The entries in this table cannot be modified by a Management Station. There is no appcLluAdminTable because all of the information needed to configure a LU6.2 LU is already present in the snaLuAdminTable. 2) appcParLuAdminTable This table contains objects which describe partner LU configuration information. The type of information includes the name and whether parallel session is supported. The rows in this table can be created, modified, and deleted by a Management Station. The appcParLuAdminRowStatus object describes the status of an entry and is used to change the status of that entry. Entries are indexed by snaNodeAdminIndex and appcParLuAdminIndex. There is a single appcParLuAdminTable for each node. For those implementations that have partner LU definitions associated with each local LU, multiple entries with the same appcParLuAdminParLuName could exist with different appcParLuAdminLocLuName. For those implementations in which partner LU definitions applies to all local LUs, it will have appcParLuAdminLocLuName set to '*ALL'. For each entry in the appcParLuAdminTable, there is one or more corresponding entry in the appcParLuOperTable. While the objects in this table describe the desired or configured values, the actual runtime values are contained in the appcParLuOperTable. 3) appcParLuOperTable This table contains objects which describe partner LU run-time operational information. The type of information includes the name and whether parallel session is supported. This table supplements the appcParLuAdminTable. Although the admin table Expires December 1994 [Page 8] Internet Draft APPC MIB July 18, 1994 entries could be global to all local LUs in a node, the oper table entries are always associated with a local LU. Entries are indexed by snaNodeAdminIndex, snaLuAdminLuIndex and appcParLuAdminIndex. The rows in this table is created as soon as there is an active session between the local and partner LU. The entries in this table cannot be modified by a Management Station. 4) appcModeAdminTable This table contains objects which describe mode configuration information. The type of information includes the name and maximum session limited. The rows in this table can be created, modified, and deleted by a Management Station. The appcModeAdminRowStatus object describes the status of an entry and is used to change the status of that entry. Entries are indexed by snaNodeAdminIndex and appcModeAdminIndex. There is a single appcModeAdminTable for each node. For those implementations that have mode definitions associated with each local and partner LU pair, multiple entries with the same appcModeAdminModeName could exist with different appcModeAdminLocLuName and appcModeAdminParLuName. For those implementations in which mode definitions applies to all local and partner LUs, it will have appcModeAdminLocLuName and appcModeAdminParLuName set to '*ALL'. For each entry in the appcModeAdminTable, there is one or more corresponding entry in the appcModeOperTable. While the objects in this table describe the desired or configured values, the actual runtime values are contained in the appcModeOperTable. 5) appcModeOperTable This table contains objects which describe mode run-time operational information. The type of information includes the name and maximum session limit. This table supplements the appcModeAdminTable. Although the admin table entries could be global to all local and partner LUs in a node, the oper table entries are always associated with a local and partner LU. Entries are indexed by snaNodeAdminIndex, snaLuAdminLuIndex, appcParLuAdminIndex, and appcModeAdminIndex. The rows in this table is created as soon as there is an active session Expires December 1994 [Page 9] Internet Draft APPC MIB July 18, 1994 between the local and partner LU for this mode. The entries in this table cannot be modified by a Management Station. 3.2.3. appcTp group The appcTp group consists of the following tables: 1) appcTpAdminTable This table contains objects which describe transaction program (TP) configuration information. The type of information includes the name and TP privileges. The rows in this table can be created, modified, and deleted by a Management Station. The appcTpAdminRowStatus object describes the status of an entry and is used to change the status of that entry. Entries are indexed by snaNodeAdminIndex and appcTpAdminIndex. There is a single appcTpAdminTable for each node. For those implementations that have TP definitions associated with each local LU, multiple entries with the same appcTpAdminTpName could exist with different appcTpAdminLocLuName. For those implementations in which TP definitions applies to all local LUs, it will have appcTpAdminLocLuName set to '*ALL'. For each entry in the appcTpAdminTable, there is one or more corresponding entry in the appcTpOperTable. While the objects in this table describe the desired or configured values, the actual runtime values are contained in the appcTpOperTable. 2) appcTpOperTable This table contains objects which describe TP run-time operational information. The type of information includes the name and TP privileges. Although the admin table entries could be global to all local LUs in a node, the oper table entries are always associated with a local LU. In addition, some TPs could be started up locally without any configuration. Therefore, this entry in the appcTpOperTable may not have a corresponding entry in the appcTpAdminTable (i.e., the Expires December 1994 [Page 10] Internet Draft APPC MIB July 18, 1994 appcTpOperTpAdminIndex is set to 0) Entries are indexed by snaNodeAdminIndex, snaLuAdminLuIndex, and appcTpOperIndex. The rows in this table is created as soon as a TP is started up. The entries in this table cannot be modified by a Management Station. 3.2.4. appcSession group The appcSession group consists of the following table: 1) appcSessnTable This table contains objects which describe APPC-specific session information. The type of information includes the PCID and the pacing counts. This table supplements the snaLuSesnTable, defined in the SNA NAU MIB module, and as such uses the same indices(i.e., snaNodeAdminIndex, snaLuAdminLuIndex, snaLuSessnRluIndex, snaLuSessnIndex). However, only entries in the snaLuSesnTable that are APPC or LU6.2 sessions, would have a corresponding entry in this table. Note that the snaLuSessnRluIndex is the same as appcParLuAdminIndex. The rows in this table are created by an Agent as soon as the entry in the snaLuSesnTable becomes 'active'. The entries in this table cannot be modified by a Management Station. 3.2.5. appcConversation group The appcConversation group consists of the following table: 1) appcConvTable This table contains objects which describe conversation information. The type of information includes the state and type. Since conversations can come up and down in a short period, it would be more useful for a Management Station, if this table also contains historical information. An entry is created by an Agent when the conversation is started but not deleted when it stops. How the entries are removed is implementation dependent and does not affect the usage of this table. The entries in this table cannot be modified by a Management Expires December 1994 [Page 11] Internet Draft APPC MIB July 18, 1994 Station. 3.2.6. appcCPIC group The appcCPIC group consists of the following tables: 1) appcCpicAdminTable This table contains objects which describe CPI-C side information. The type of information includes the symbolic destination name and local LU name. The rows in this table can be created, modified, and deleted by a Management Station. The appcCpicAdminRowStatus object describes the status of an entry and is used to change the status of that entry. Entries are indexed by appcCpicAdminIndex. There is a single appcCpicAdminTable for the system. For those implementations that have CPI-C definitions associated with each local LU, multiple entries with the same appcCpicAdminSymbDestName could exist with different appcCpicAdminLocLuName. For those implementations in which CPI-C definitions applies to all local LUs, it will have appcCpicAdminLocLuName set to '*ALL'. For each entry in the appcCpicAdminTable, there is one or more corresponding entry in the appcCpicOperTable. While the objects in this table describe the desired or configured values, the actual runtime values are contained in the appcCpicOperTable. 2) appcCpicOperTable This table contains objects which describe CPI-C run-time operational information. The type of information includes the symbolic destination name and local LU name. This table supplements the appcCpicAdminTable. Although the admin table entries could be global to all local LUs in a node, the oper table entries are always associated with a local LU. Entries are indexed by appcCpicOperIndex. The rows in this table is created as soon as it is being used by an Expires December 1994 [Page 12] Internet Draft APPC MIB July 18, 1994 active TP. The entries in this table cannot be 3.2.7. Conformance statement Compliance of the SNMPv2 management entity to the APPC MIB is defined in terms of following conformance units called groups. Unconditionally mandatory groups: appcGlobalGroup, appcDefaultGroup, appcLluGroup, appcParLuGroup, appcModeGroup, appcTpGroup, appcSessionGroup, and appcConversationGroup. Conditionally mandatory groups: appcStatControlGroup - mandatory only for those entities which supports the option of activating and deactivating statistic collection and counting. appcCpicGroup - mandatory only for those entities which supports CPI-C. Refinement of requirements for objects access: an Agent which does not implement row creation for appcParLuAdminTable, appcModeAdminTable, appcTpAdminTable and appcCpicAdminTable must at least support object modification requests (i.e., read-write access instead of read-create). 3.3. APPC MIB special feature This section describes the mechanism used for row creation in the Admin tables. 3.3.1. Row Creation mechanism The row creation mechanism for the Admin tables in this MIB module is based on the use of the RowStatus object. Restriction of some operations for specific tables are described in each table. In particular, before accepting the 'destroy' value for an entry, an Agent has to verify the operational state of the corresponding entry in the Oper table. Expires December 1994 [Page 13] Internet Draft APPC MIB July 18, 1994 4. Object Definitions APPC-MIB DEFINITIONS ::= BEGIN IMPORTS DisplayString, RowStatus, TimeStamp, InstancePointer FROM SNMPv2-TC experimental, Counter32, Gauge32, Integer32, OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF snaNodeAdminIndex, snaLuAdminLuIndex, snaLuSessnIndex, snaLuSessnRluIndex FROM SNA-NAU-MIB; appcMIB MODULE-IDENTITY LAST-UPDATED "9407181800Z" ORGANIZATION "IETF SNA NAU MIB Working Group" CONTACT-INFO " Michael Allen Networking Systems IBM Corporation Research Triangle Park, NC 27709 Tel: 1 919 254 4442 E-mail: moallen@vnet.ibm.com Zbigniew Kielczewski Eicon Technology Inc. 2196 32nd Avenue Lachine, Que H8T 3H7 Canada Tel: 1 514 631 2592 E-mail: zbig@eicon.qc.ca William Kwan CrossComm Corporation 450 Donald Lynch Blvd. Marlboro, MA 01752 Tel: 1 508 229 5429 E-mail: kwan@crosscomm.com Expires December 1994 [Page 14] Internet Draft APPC MIB July 18, 1994 " DESCRIPTION "This is the MIB module for objects used to manage network devices with APPC capabilities." ::= { experimental 999 } appcObjects OBJECT IDENTIFIER ::= { appcMIB 1 } appcGlobal OBJECT IDENTIFIER ::= { appcObjects 1 } appcLu OBJECT IDENTIFIER ::= { appcObjects 2 } appcTp OBJECT IDENTIFIER ::= { appcObjects 3 } appcSession OBJECT IDENTIFIER ::= { appcObjects 4 } appcConversation OBJECT IDENTIFIER ::= { appcObjects 5 } appcCPIC OBJECT IDENTIFIER ::= { appcObjects 6 } -- ********************************************************************* -- Objects in this MIB will be used to model a SNA device which contains -- one or more Nodes of type 2.1. -- The structure of tables is related to tables defined in the SNA NAU MIB. -- In particular, the tables for Local LUs and Sessions use the same -- system of indices as corresponding tables in SNA NAU MIB and contain -- only information specific to APPC. -- -- 1. APPC Global Objects - global stats, defaults, controls -- 2. APPC Defined Lu Tables - Oper only (Admin in NAU MIB) -- 3. APPC Defined Partner Lu Tables - Admin and Oper -- 4. APPC Mode Tables - Admin and Oper -- 5. APPC TP Tables - Admin and oper -- 6. APPC Session Tables - Oper and Stats -- 7. APPC Conversation Table - Oper only -- 8. APPC CPIC side info - Admin and oper -- ********************************************************************* -- ********************************************************************* -- APPC Global Objects -- These objects are organised in a table and defined for each PU 2.1 -- ********************************************************************* appcGlobalTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcGlobalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC global info Table" ::= { appcGlobal 1 } Expires December 1994 [Page 15] Internet Draft APPC MIB July 18, 1994 appcGlobalEntry OBJECT-TYPE SYNTAX AppcGlobalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about Nodes, indexed by Node Index from NAU MIB." INDEX { snaNodeAdminIndex } ::= { appcGlobalTable 1 } AppcGlobalEntry ::= SEQUENCE { appcNbLocLUInUse Gauge32, appcNbSessnInUse Gauge32 } appcNbLocLUInUse OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "the number of local LUs currently active." ::= { appcGlobalEntry 1 } appcNbSessnInUse OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of active sessions between local LUs and remote LUs." ::= { appcGlobalEntry 2 } -- ********************************************************************* -- APPC Statistics Control Objects -- --------------------------------------------------------------------- -- The following simple objects allow: -- * the collection of APPC Session Information counters -- to be started and stopped -- * the collection of APPC Session RSCVs -- to be started and stopped -- -- These objects are for implementations that wish to provide -- this level of operational control. This group should be Expires December 1994 [Page 16] Internet Draft APPC MIB July 18, 1994 -- optional in the conformance section of the MIB. -- -- ********************************************************************* appcStatCntrlGroup OBJECT IDENTIFIER ::= { appcGlobal 2 } appcStatCntrlStatus OBJECT-TYPE SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the current collection options in effect notActive collection of counters and some names is not active. active collection of counters and some names is active." ::= { appcStatCntrlGroup 1 } appcStatCntrlRscv OBJECT-TYPE SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates the current collection options in effect notActive collection of route selection control vectors is not active. active collection of route selection control vectors is active." ::= { appcStatCntrlGroup 2 } appcStatCntrlRscvTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the appcStatCntrlRscv object last changed. This time is in hundreds of a second." Expires December 1994 [Page 17] Internet Draft APPC MIB July 18, 1994 ::= { appcStatCntrlGroup 3 } appcStatCntrlCtrStatus OBJECT-TYPE SYNTAX INTEGER { notActive(1), active(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether or not the appc session counters are active. This object reflects the combination of the appcStatCntrlStatus object and any other product dependent object(s). The values are: notActive collection of counters and some names is not active. active collection of counters and some names is active." ::= { appcStatCntrlGroup 4 } appcStatCntrlCtrStatusTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the appcStatCntrlCtrStatus object last changed. This time is in hundreds of a second." ::= { appcStatCntrlGroup 5 } -- ****************************************************************** -- -- Table of APPC defaults per SNA node -- -- ****************************************************************** appcDefaultTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcDefaultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of APPC default settings per SNA node." ::= { appcGlobal 3 } Expires December 1994 [Page 18] Internet Draft APPC MIB July 18, 1994 appcDefaultEntry OBJECT-TYPE SYNTAX AppcDefaultEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC default settings per SNA node." INDEX { snaNodeAdminIndex } ::= { appcDefaultTable 1 } AppcDefaultEntry ::= SEQUENCE { appcDefaultModeName DisplayString, appcDefaultLuAlias DisplayString, appcDefaultImplInbndPlu INTEGER, appcDefaultMaxMcLlSndSize Gauge32, appcDefaultFileSpec DisplayString, appcDefaultTpOperation INTEGER, appcDefaultTpConvSecRqd INTEGER } appcDefaultModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the mode name to be used under the following conditions: When an incoming BIND request contains a mode name not defined at the local node. The parameters defined for this mode are used for the inbound implicit mode capability. When an APPC program issues an [MC_]ALLOCATE, [MC_]SEND_CONVERSATION, or CNOS verb, or when a CPI-C program issues an Allocate (CMALLC) call, specifying a mode name not defined at the local node. The parameters defined for this mode are used for the outbound implicit mode capability. Display convention A get operation against this object will return the string 'BLANK' if the actual value is 8 spaces. This convention Expires December 1994 [Page 19] Internet Draft APPC MIB July 18, 1994 is intended to prevent operator confusion and is consistent with the practice of some existing implementations. " ::= { appcDefaultEntry 1 } appcDefaultLuAlias OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the alias of the local LU that is to serve as the default LU. This The default LU is the one to which are routed inbound BIND requests that exclude the secondary LU name. This local LU alias must have been previously defined in snaLuAdminName for the intended local LU." ::= { appcDefaultEntry 2 } appcDefaultImplInbndPlu OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether or not inbound implicit partner LU support is enabled. The following values are defined: YES Specifies that inbound implicit partner LU support is enabled, which provides the capability to accept an incoming BIND request that contains a partner LU name that is not defined at the local node. NO Specifies that inbound implicit partner LU support is disabled, which means that an incoming bind that specifies a partner LU that is not defined at the local node will be rejected." ::= { appcDefaultEntry 3 } appcDefaultMaxMcLlSndSize OBJECT-TYPE Expires December 1994 [Page 20] Internet Draft APPC MIB July 18, 1994 SYNTAX Gauge32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum size of a logical record to be used on a mapped conversation for sending data to either the inbound or outbound implicit partner LU. The size is the number of bytes in the logical record, as indicated in the LL field of the record. The default value is 32767." ::= { appcDefaultEntry 4 } appcDefaultFileSpec OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) MAX-ACCESS read-create STATUS current DESCRIPTION "The local file specification that is to be searched by the APPC attach manager when no DEFINE_TP verb has been issued for the TP name received on an incoming attach. In this case, the attach manager will attempt to start a program whose file name is the same as the incoming TP name. If found, the program is loaded. If not found, the attach is rejected. The value '*' indicates that the normal search path for executable programs is to be used for locating an undefined transaction program. A null string indicates that there is no default file specification for undefined transaction programs." ::= { appcDefaultEntry 5 } appcDefaultTpOperation OBJECT-TYPE SYNTAX INTEGER { queuedOperatorStarted(1), queuedOperatorPreloaded(2), queuedAmStarted(3), nonqueuedAmStarted(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies how the program will be started. Expires December 1994 [Page 21] Internet Draft APPC MIB July 18, 1994 queuedOperatorStarted -- Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, APPC will issue a message to the operator to start the specified program. Subsequent attaches that arrive while the program is active will be queued. queuedOperatorPreloaded -- Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, the Attach will be rejected. The APPC attach manager determines that a TP has started upon reception of an APPC RECEIVE_ALLOCATE verb or a CPI-C program Accept_Conversation (CMACCP) call. No message is sent to the operator. Subsequent attaches that arrive while the program is active are queued. queuedAmStarted -- Specifies that one version of the program will be run at a time and will be started by the APPC attach manager. Subsequent attaches that arrive while the program is active will be queued. nonqueuedAmStarted -- Specifies that multiple copies of the program will be run at a time and will be started by the APPC attach manager." ::= { appcDefaultEntry 6 } appcDefaultTpConvSecRqd OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether or not conversation security will be used for default TPs. YES Specifies that the incoming attach must contain a valid user ID and password. Expires December 1994 [Page 22] Internet Draft APPC MIB July 18, 1994 NO Specifies that the incoming attach does not have to contain security information." ::= { appcDefaultEntry 7 } -- ********************************************************************* -- APPC LU information -- --------------------------------------------------------------------- -- -- The entries in the following table supplement the entries in the NAU -- MIB table snaLuOperTable. However, these entries do not AUGMENT -- snaLuOperEntry, since the entries here provide APPC-level information, -- which is not applicable to non-6.2 LUs. -- -- An appcLluAdminTable is not needed, since all of the -- information needed to define a local 6.2 LU on most implementations -- is already present in snaLuAdminTable. There are some operational -- characteristics for a local 6.2 LU that we do need to model, hence -- this appcLluOperTable. -- -- ********************************************************************* appcLluOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcLluOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC Local Lu Table. This table supplements snaLuOperTable for type 6.2 LUs." ::= { appcLu 1 } appcLluOperEntry OBJECT-TYPE SYNTAX AppcLluOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about local APPC LUs. This entry supplements the information in snaLuOperEntry, uses the same indices, but entries in this table are present only for 6.2 LUs." INDEX { snaNodeAdminIndex, snaLuAdminLuIndex } ::= { appcLluOperTable 1 } Expires December 1994 [Page 23] Internet Draft APPC MIB July 18, 1994 AppcLluOperEntry ::= SEQUENCE { appcLluOperDefType INTEGER, appcLluOperSessLimit Integer32, appcLluOperBindRspMayQ INTEGER, appcLluOperDefaultLu INTEGER, appcLluOperCPlu INTEGER } appcLluOperDefType OBJECT-TYPE SYNTAX INTEGER { sysdef(1), operator(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the LU definition was specified in the nodes system definitions, by operator command (either locally or from network management workstation)." ::= { appcLluOperEntry 1 } appcLluOperSessLimit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of session supported by this LU." ::= { appcLluOperEntry 2 } appcLluOperBindRspMayQ OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the local LU, as the sender of a BIND request, allows a remote partner LU to delay sending the BIND response if the partner LU cannot process the BIND request immediately." Expires December 1994 [Page 24] Internet Draft APPC MIB July 18, 1994 ::= { appcLluOperEntry 3 } appcLluOperDefaultLu OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the LU is the default LU, to which are routed inbound BIND requests that exclude the secondary LU name." ::= { appcLluOperEntry 4 } appcLluOperCPlu OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the LU is the control point (CP) for the node." ::= { appcLluOperEntry 5 } -- ********************************************************************* -- APPC Partner LU Admin Table -- --------------------------------------------------------------------- -- This table contains information about partner LU's -- ********************************************************************* appcParLuAdminTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcParLuAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC Partner LU administrative Table" ::= { appcLu 2 } appcParLuAdminEntry OBJECT-TYPE SYNTAX AppcParLuAdminEntry MAX-ACCESS not-accessible Expires December 1994 [Page 25] Internet Draft APPC MIB July 18, 1994 STATUS current DESCRIPTION "Entry of APPC Partner LU Information Table. It is indexed by snaNodeAdminIndex plus an index for the partner LU." INDEX { snaNodeAdminIndex, appcParLuAdminIndex } ::= { appcParLuAdminTable 1 } AppcParLuAdminEntry ::= SEQUENCE { appcParLuAdminIndex Integer32, appcParLuAdminLocLuName DisplayString, appcParLuAdminParLuName DisplayString, appcParLuAdminAlias DisplayString, appcParLuAdminDefType INTEGER, appcParLuAdminDefParaSessSup INTEGER, appcParLuAdminDefCnosSup INTEGER, appcParLuAdminDefSessSec INTEGER, appcParLuAdminDefConvSec INTEGER, appcParLuAdminDefAlVerSup INTEGER, appcParLuAdminLinkName DisplayString, appcParLuAdminRowStatus RowStatus } appcParLuAdminIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for partner LU admin instances." ::= { appcParLuAdminEntry 1 } appcParLuAdminLocLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-create STATUS current DESCRIPTION "The SNA name of the local LU to which this partner LU definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. Expires December 1994 [Page 26] Internet Draft APPC MIB July 18, 1994 The reserved value '*ALL' indicates that the partner LU definition applies to all local LUs, and not just to a single local LU. Row creation conventions: When row creation is attempted, the agent must verify that the partner LU name in the new row is not the same as in an existing partner LU definition for the same local LU name. If it is, the creation must fail. Implementations that do not support definition of modes on an LU by LU basis will reject any attempt to set this object to a value other than '*ALL'." ::= { appcParLuAdminEntry 2 } appcParLuAdminParLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-create STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcParLuAdminEntry 3 } appcParLuAdminAlias OBJECT-TYPE SYNTAX DisplayString (SIZE (0..48)) MAX-ACCESS read-create STATUS current DESCRIPTION "A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string." ::= { appcParLuAdminEntry 4 } appcParLuAdminDefType OBJECT-TYPE SYNTAX INTEGER { sysdef(1), operator(2), dynamic(3) } MAX-ACCESS read-create Expires December 1994 [Page 27] Internet Draft APPC MIB July 18, 1994 STATUS current DESCRIPTION "Indicates whether the LU definition was specified in the nodes system definitions, by operator command (either locally or from network management workstation), or was dynamically created in response to an Allocate or Bind." ::= { appcParLuAdminEntry 5 } appcParLuAdminDefParaSessSup OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defined Parallel Sessions Supported. Indicates whether or not multiple session between the partner LU and its associated local LU are permitted." ::= { appcParLuAdminEntry 6 } appcParLuAdminDefCnosSup OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defined CNOS Supported. Indicates whether or not Change Number of Sessions (CNOS) will be used to negotiate session limits between the logical points." ::= { appcParLuAdminEntry 7 } appcParLuAdminDefSessSec OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create Expires December 1994 [Page 28] Internet Draft APPC MIB July 18, 1994 STATUS current DESCRIPTION "Specifies the type of security information that a local LU will accept on BIND requests it receives from the partner LU. yes -- Specifies that the BIND request may carry a password that will be verified upon receipt. no -- Specifies that the BIND request may carry a password but no session level security verification will be done." ::= { appcParLuAdminEntry 8 } appcParLuAdminDefConvSec OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Level of access security that will be accepted on attach requests received from the partner LU. Possible values are: yes -- conversation level security is supported. no -- conversation level security is not supported." ::= { appcParLuAdminEntry 9 } appcParLuAdminDefAlVerSup OBJECT-TYPE SYNTAX INTEGER { none(1), already(2), persistent(3), already-persistent(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies support for different levels of verified security in ATTACH requests received from this remote LU. This object is only valid if conversation level security is supported. Possible values are: Expires December 1994 [Page 29] Internet Draft APPC MIB July 18, 1994 none - No allocation requests will be accepted that includes already-verified or persistent verification indications. The requests must include a user id and password (optionally a profile). already - Allocation requests will be accepted that include already-verified indications. Persistent verification indications will not be accepted. persistent - Allocation requests will be accepted that include persistent verification indications. Already-verified indications will not be accepted. already-persistent - Allocation requests will be accepted that include already-verified or persistent verification indications." ::= { appcParLuAdminEntry 10 } appcParLuAdminLinkName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..48)) MAX-ACCESS read-create STATUS current DESCRIPTION "Local name for the link that provides connection to partner LU. This object may contain a zero-length string if the link name is not specified or if link name is not applicable (as for APPN-level nodes)." ::= { appcParLuAdminEntry 11 } appcParLuAdminRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used by a Management Station to create or delete the row entry in the appcParLuAdminTable following the RowStatus textual convention. " Expires December 1994 [Page 30] Internet Draft APPC MIB July 18, 1994 ::= { appcParLuAdminEntry 12 } -- ********************************************************************* -- APPC Partner Lu Oper Table -- ********************************************************************* appcParLuOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcParLuOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of active partner LUs" ::= { appcLu 3 } appcParLuOperEntry OBJECT-TYPE SYNTAX AppcParLuOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry in operational table of partner LUs." INDEX { snaNodeAdminIndex, snaLuAdminLuIndex, appcParLuAdminIndex } ::= { appcParLuOperTable 1 } AppcParLuOperEntry ::= SEQUENCE { appcParLuOperLocLuName DisplayString, appcParLuOperParLuName DisplayString, appcParLuOperParLuAlias DisplayString, appcParLuOperState INTEGER, appcParLuOperActParaSessSup INTEGER, appcParLuOperActCnosSup INTEGER, appcParLuOperActSessSec INTEGER, appcParLuOperActConvSec INTEGER, appcParLuOperActAlVerSup INTEGER, appcParLuOperLinkName DisplayString } appcParLuOperLocLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) Expires December 1994 [Page 31] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the local LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. This value is redundant, because the snaLuAdminLuIndex could be used to retrieve this value from the snaLuAdminTable, but the value is duplicated here to simplify management station application programming." ::= { appcParLuOperEntry 1 } appcParLuOperParLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcParLuOperEntry 2 } appcParLuOperParLuAlias OBJECT-TYPE SYNTAX DisplayString (SIZE (0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string." ::= { appcParLuOperEntry 3 } appcParLuOperState OBJECT-TYPE SYNTAX INTEGER { inactive (1), active (2) } MAX-ACCESS read-only STATUS current Expires December 1994 [Page 32] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "The value identifies the current operational state of this LU. active (2) - the LU is defined and is able to receive BIND. inactive (1) - the LU has a session count equal to 0." ::= { appcParLuOperEntry 4 } appcParLuOperActParaSessSup OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Active Parallel Sessions Supported. Indicates whether or not multiple session between the partner LU and its associated local LU are permitted." ::= { appcParLuOperEntry 5 } appcParLuOperActCnosSup OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Active CNOS Supported. Indicates whether or not Change Number of Sessions (CNOS) will be used to negotiate session limits between the logical points." ::= { appcParLuOperEntry 6 } appcParLuOperActSessSec OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) Expires December 1994 [Page 33] Internet Draft APPC MIB July 18, 1994 } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the type of security information that a local LU will accept on BIND requests it receives from the partner LU. yes -- Specifies that the BIND request may carry a password that will be verified upon receipt. no -- Specifies that the BIND request may carry a password but no session level security verification will be done." ::= { appcParLuOperEntry 7 } appcParLuOperActConvSec OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Level of access security that will be accepted on attach requests received from the partner LU. Possible values are: yes -- conversation level security is supported. no -- conversation level security is not supported." ::= { appcParLuOperEntry 8 } appcParLuOperActAlVerSup OBJECT-TYPE SYNTAX INTEGER { none(1), already(2), persistent(3), already-persistent(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies support for different levels of verified security in ATTACH requests received from this remote LU. This object is Expires December 1994 [Page 34] Internet Draft APPC MIB July 18, 1994 only valid if conversation level security is supported. Possible values are: none - No allocation requests will be accepted that includes already-verified or persistent verification indications. The requests must include a user id and password (optionally a profile). already - Allocation requests will be accepted that include already-verified indications. Persistent verification indications will not be accepted. persistent - Allocation requests will be accepted that include persistent verification indications. Already-verified indications will not be accepted. already-persistent - Allocation requests will be accepted that include already-verified or persistent verification indications." ::= { appcParLuOperEntry 9 } appcParLuOperLinkName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..48)) MAX-ACCESS read-only STATUS current DESCRIPTION "Local name for the link that provides connection to partner LU. This object may contain a zero-length string if the link name is not specified or if link name is not applicable (as for APPN-level nodes)." ::= { appcParLuOperEntry 10 } -- ********************************************************************* -- APPC Mode Table -- --------------------------------------------------------------------- -- This table contains information about session mode definitions. -- Modes can be defined by creating a row in this table. -- Modes that have active sessions appear in the appcModeOperTable. -- ********************************************************************* appcModeAdminTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcModeAdminEntry MAX-ACCESS not-accessible Expires December 1994 [Page 35] Internet Draft APPC MIB July 18, 1994 STATUS current DESCRIPTION "APPC Mode Table" ::= { appcLu 4 } appcModeAdminEntry OBJECT-TYPE SYNTAX AppcModeAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC Mode Information Table." INDEX { snaNodeAdminIndex, appcModeAdminIndex } ::= { appcModeAdminTable 1 } AppcModeAdminEntry ::= SEQUENCE { appcModeAdminIndex Integer32, appcModeAdminModeName DisplayString, appcModeAdminLocLuName DisplayString, appcModeAdminParLuName DisplayString, appcModeAdminCosName DisplayString, appcModeAdminDefType INTEGER, appcModeAdminSessEndTpName DisplayString, appcModeAdminMaxSessLimit Gauge32, appcModeAdminConWinAutoActLimit Gauge32, appcModeAdminAdaptivePacing INTEGER, appcModeAdminRecvPacWinSz Integer32, appcModeAdminSendPacWinSz Integer32, appcModeAdminPrefRecvRuSz Integer32, appcModeAdminPrefSendRuSz Integer32, appcModeAdminRecvRuSzUpBnd Integer32, appcModeAdminSendRuSzUpBnd Integer32, appcModeAdminRecvRuSzLoBnd Integer32, appcModeAdminSendRuSzLoBnd Integer32, appcModeAdminDfSyncLvl INTEGER, appcModeAdminDfCrypto INTEGER, appcModeAdminSingSessReinit INTEGER, appcModeAdminAltCode INTEGER, appcModeAdminCompression INTEGER, appcModeAdminInBoundCompLevel INTEGER, appcModeAdminOutBoundCompLevel INTEGER, Expires December 1994 [Page 36] Internet Draft APPC MIB July 18, 1994 appcModeAdminCompRleBeforeLZ INTEGER, appcModeAdminRowStatus RowStatus } appcModeAdminIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for entry in mode definition table." ::= { appcModeAdminEntry 1 } appcModeAdminModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). Row creation conventions: When row creation is attempted, the agent must verify that the mode name in the new row is not the same as an existing mode definition. If it is, the creation must fail. If the desired mode name is the default blank mode name, the appcModeAdminModeName object must be set to the reserved value 'BLANK', which represents the value of 8 space characters operationally. A set with a shorter string of space characters will be padded to 8 spaces by the agent. Display convention A get operation against this object will return the string 'BLANK' if the actual value is 8 spaces. This convention is intended to prevent operator confusion and is consistent with the practice of some existing implementations. " ::= { appcModeAdminEntry 2 } Expires December 1994 [Page 37] Internet Draft APPC MIB July 18, 1994 appcModeAdminLocLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-create STATUS current DESCRIPTION "The SNA name of the local LU to which this mode definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. The reserved value '*ALL' indicates that the mode definition applies to all local LUs for the SNA node identified by snaNodeAdminIndex, and not just to a single local LU. Row creation conventions: When row creation is attempted, the agent must verify that the local LU name in the new row is not the same as in an existing mode definition for the same mode name. If it is, the creation must fail. Implementations that do not support definition of modes on an LU-by-LU basis will reject any attempt to set this object to a value other than '*ALL'." ::= { appcModeAdminEntry 3 } appcModeAdminParLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-create STATUS current DESCRIPTION "The SNA name of the partner LU to which this mode definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. The reserved value '*ALL' indicates that the mode definition applies to all partner LUs for the SNA node identified by snaNodeAdminIndex, and not just to a single partner LU. Row creation conventions: When row creation is attempted, the agent must verify that the partner LU name in the new row is not the same as in an existing mode definition for the same mode name and the Expires December 1994 [Page 38] Internet Draft APPC MIB July 18, 1994 same local LU name. If it is, the creation must fail. Implementations that do not support definition of modes on an LU-by-LU basis will reject any attempt to set this object to a value other than '*ALL'." ::= { appcModeAdminEntry 4 } appcModeAdminCosName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the class of service (COS) name associated with this mode. If the implementation does not support COS names, a null string is returned." ::= { appcModeAdminEntry 5 } appcModeAdminDefType OBJECT-TYPE SYNTAX INTEGER { sysdef(1), dynamic(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the mode definition was specified in the nodes system definitions or was dynamically created." ::= { appcModeAdminEntry 6 } appcModeAdminSessEndTpName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the name of the transaction program (TP) to be invoked when a session using this mode is deactivated or ended. If no such TP is defined, this object is a null string. When the TP name consists entirely of displayable EBCDIC codepoints, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC codepoint (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that Expires December 1994 [Page 39] Internet Draft APPC MIB July 18, 1994 is equivalent to a hexadecimal display of the EBCDIC codepoints. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 4-byte ASCII display string '06F1'. " ::= { appcModeAdminEntry 7 } appcModeAdminMaxSessLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum value that the local LU is to use, during CNOS processing, for the session limit. The local LU, as a target LU, will negotiate a higher session limit it receives in the CNOS request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value." ::= { appcModeAdminEntry 8 } appcModeAdminConWinAutoActLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the limit on the number of contention winner sessions to be automatically activated when the minimum number of contention winner sessions increases (as a result of CNOS processing). The actual number of sessions activated is the lesser of this value and the new minimum number of contention winner sessions. " ::= { appcModeAdminEntry 9 } appcModeAdminAdaptivePacing OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether adaptive session-level pacing is supported. This is only supported for APPN nodes. Expires December 1994 [Page 40] Internet Draft APPC MIB July 18, 1994 This value is used for negotiation during session activations (SNA BIND)." ::= { appcModeAdminEntry 10 } appcModeAdminRecvPacWinSz OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the size of the receive pacing window. This value is used for negotiation during session activations (SNA BIND). If appcModeAdminAdaptivePacing is yes, then this value is set to 0. If appcModeAdminAdaptivePacing is no and this value is set to 0, then pacing is not supported. The meaning of this value when set to 0 is as follows: appcModeAdminAdaptivePacing = yes No limit on window size appcModeAdminAdaptivePacing = no No pacing is supported" ::= { appcModeAdminEntry 11 } appcModeAdminSendPacWinSz OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the size of the send pacing window. This value is used for negotiation during session activations (SNA BIND). If appcModeAdminAdaptivePacing is yes,then this value is set to 0.If appcModeAdminAdaptivePacing is no and this value is set to 0, then pacing is not supported. The meaning of this value when set to 0 is as follows: appcModeAdminAdaptivePacing = yes No limit on window size appcModeAdminAdaptivePacing = no No pacing is supported" ::= { appcModeAdminEntry 12 } appcModeAdminPrefRecvRuSz OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current Expires December 1994 [Page 41] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "Specifies the preferred receive RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeAdminRecvRuSzUpBnd and greater than or equal to the value specified in appcModeAdminRecvRuSzLoBnd. The local LU specifies this value for the receive maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeAdminRecvRuSzUpBnd value or down to the appcModeAdminRecvRuSzLoBnd value." ::= { appcModeAdminEntry 13 } appcModeAdminPrefSendRuSz OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the preferred send RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeAdminSendRuSzUpBnd and greater than or equal to the value specified in appcModeAdminSendRuSzLoBnd. The local LU specifies this value for the send maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeAdminSendRuSzUpBnd value or down to the appcModeAdminSendRuSzLoBnd value." ::= { appcModeAdminEntry 14 } appcModeAdminRecvRuSzUpBnd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the upper bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeAdminEntry 15 } appcModeAdminSendRuSzUpBnd OBJECT-TYPE SYNTAX Integer32 Expires December 1994 [Page 42] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the upper bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeAdminEntry 16 } appcModeAdminRecvRuSzLoBnd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the lower bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeAdminEntry 17 } appcModeAdminSendRuSzLoBnd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the lower bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeAdminEntry 18 } appcModeAdminDfSyncLvl OBJECT-TYPE SYNTAX INTEGER { none(1), noneConfirm(2), noneConfirmSyncPoint(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the sync level support. This value is used for negotiation during session activations (SNA BIND). none - No sync level is supported. noneConfirm - None and Confirm levels supported. Expires December 1994 [Page 43] Internet Draft APPC MIB July 18, 1994 noneConfirmSyncPoint - All sync levels is supported. " ::= { appcModeAdminEntry 19 } appcModeAdminDfCrypto OBJECT-TYPE SYNTAX INTEGER { notsupported(1), mandatory(2), selective(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether session-level cryptography is supported. This value is used for negotiation during session activations (SNA BIND). notsupported - Specifies session-level cryptography is not to be used. mandatory - Specifies session-level cryptography must be used. selective - Specifies session-level cryptography is required just on selected requests flowing on the sessions." ::= { appcModeAdminEntry 20 } appcModeAdminSingSessReinit OBJECT-TYPE SYNTAX INTEGER { operatorControlled(1), primaryOnly(2), secondaryOnly(3), primaryOrSecondary(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the responsibility for session reinitiation of a single session with the remote LU (when the session goes down). The local LU uses this parameter to specify the session reinitiation responsibility in session activation (SNA BIND) requests and responses. The value is only supported if the remote LU is defined to not support parallel sessions (i.e., appcInRluDefParaSessSup is set to no). Expires December 1994 [Page 44] Internet Draft APPC MIB July 18, 1994 operatorControlled - specifies that neither LU will automatically attempt to reinitiate the session. The operator on either side will manually reactivate the session. A contention race (both side reinitiating at the same time) is won by the LU with the lexigraphically greater fully-qualified LU name. primaryOnly - specifies that the primary LU will automatically attempt to reinitiate the session. secondaryOnly - specifies that the secondary LU will automatically attempt to reinitiate the session. primaryOrSecondary - specifies that either the primary or the secondary may automatically attempt to reinitiate the session. A contention race is handled the same way as with operatorControlled. " ::= { appcModeAdminEntry 21 } appcModeAdminAltCode OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether an alternate code is supported. yes - ASCII no - EBCDIC This value is used for negotiation during session activations (SNA BIND)." ::= { appcModeAdminEntry 22 } appcModeAdminCompression OBJECT-TYPE SYNTAX INTEGER { prohibited(1), required(2), negotiable(3) } Expires December 1994 [Page 45] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LU's. The level of compression is also negotiated." ::= { appcModeAdminEntry 23 } appcModeAdminInBoundCompLevel OBJECT-TYPE SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcModeAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like Expires December 1994 [Page 46] Internet Draft APPC MIB July 18, 1994 compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeAdminEntry 24 } appcModeAdminOutBoundCompLevel OBJECT-TYPE SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcModeAdminCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeAdminEntry 25 } appcModeAdminCompRleBeforeLZ OBJECT-TYPE SYNTAX INTEGER { yes(1), Expires December 1994 [Page 47] Internet Draft APPC MIB July 18, 1994 no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used." ::= { appcModeAdminEntry 26 } appcModeAdminRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used by a Management Station to create or delete the row entry in the appcModeAdminTable following the RowStatus textual convention. " ::= { appcModeAdminEntry 27 } -- ********************************************************************* -- APPC Mode Oper Table -- --------------------------------------------------------------------- -- This table contains operational information about session mode entries -- -- Can we put CNOS support into the entries in this table? How would -- it be done? Admin values for each oper value on session limits and -- then have a AdminCnos object that would trigger the verb? -- -- ********************************************************************* appcModeOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcModeOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Operational APPC Mode Information" Expires December 1994 [Page 48] Internet Draft APPC MIB July 18, 1994 ::= { appcLu 5 } appcModeOperEntry OBJECT-TYPE SYNTAX AppcModeOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC mode operational information table. This entry does not augment the appcModeAdminEntry, but reflects an actual operational mode for a given local LU-remote LU pair." INDEX { snaNodeAdminIndex, snaLuAdminLuIndex, appcParLuAdminIndex, appcModeAdminIndex } ::= { appcModeOperTable 1 } AppcModeOperEntry ::= SEQUENCE { appcModeOperLluName DisplayString, appcModeOperRluName DisplayString, appcModeOperModeName DisplayString, appcModeOperCosName DisplayString, appcModeOperDefType INTEGER, appcModeOperSessEndTpName DisplayString, appcModeOperSessLimit Gauge32, appcModeOperMaxSessLimit Gauge32, appcModeOperConWinAutoActLimit Gauge32, appcModeOperDrainSelf INTEGER, appcModeOperDrainPart INTEGER, appcModeOperMinCwinLimit Gauge32, appcModeOperMinClosLimit Gauge32, appcModeOperRecvPacWinSz Gauge32, appcModeOperSendPacWinSz Gauge32, appcModeOperPrefRecvRuSz Integer32, appcModeOperPrefSendRuSz Integer32, appcModeOperRecvRuSzUpBnd Integer32, appcModeOperSendRuSzUpBnd Integer32, appcModeOperRecvRuSzLoBnd Integer32, appcModeOperSendRuSzLoBnd Integer32, appcModeOperDfSyncLvl INTEGER, appcModeOperDfCrypto INTEGER, appcModeOperSingSessReinit INTEGER, Expires December 1994 [Page 49] Internet Draft APPC MIB July 18, 1994 appcModeOperAltCode INTEGER, appcModeOperCNOSNeg INTEGER, appcModeOperActSess Gauge32, appcModeOperPndSess Gauge32, appcModeOperActCwin Gauge32, appcModeOperActClos Gauge32, appcModeOperPndCwin Gauge32, appcModeOperPndClos Gauge32, appcModeOperPtmCwin Gauge32, appcModeOperPtmClos Gauge32, appcModeOperFreeSessLst Gauge32, appcModeOperWaitReqLst Gauge32, appcModeOperCompression INTEGER, appcModeOperInBoundCompLevel INTEGER, appcModeOperOutBoundCompLevel INTEGER, appcModeOperCompRleBeforeLZ INTEGER } appcModeOperLluName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the fully-qualified local LU name. This field is from 1 to 17 characters in length, in the form of NetID.LUName. The period(.) is not present when there is no NetID." ::= { appcModeOperEntry 1 } appcModeOperRluName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the fully-qualified remote LU name. This field is from 1 to 17 characters in length, in the form of NetID.LUName. The period(.) is not present when there is no NetID." ::= { appcModeOperEntry 2 } appcModeOperModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current Expires December 1994 [Page 50] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). Row creation conventions: When row creation is attempted, the agent must verify that the mode name in the new row is not the same as an existing mode definition. If it is, the creation must fail. If the desired mode name is the default BLANK mode name, the appcModeAdminModeName object must be set to 8 spaces. A set with a shorter string of space characters will be padded to 8 spaces by the agent. Display convention A get operation against this object will return the string 'BLANK' if the actual value is 8 spaces. This convention is intended to prevent operator confusion and is consistent with the practice of some existing implementations. " ::= { appcModeOperEntry 3 } appcModeOperCosName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the class of service (COS) name associated with this mode. If the implementation does not support COS names, a zero-length string is returned." ::= { appcModeOperEntry 4 } appcModeOperDefType OBJECT-TYPE SYNTAX INTEGER { sysdef(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION Expires December 1994 [Page 51] Internet Draft APPC MIB July 18, 1994 "Indicates whether the mode definition was specified in the nodes system definitions or was dynamically created." ::= { appcModeOperEntry 5 } appcModeOperSessEndTpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the name of the transaction program (TP) to be invoked when a session using this mode is deactivated or ended. If the name is NULL, no transaction program is invoked. When the TP name consists entirely of displayable EBCDIC codepoints, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC codepoint (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC codepoints. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 4-byte ASCII display string '06F1'. " ::= { appcModeOperEntry 6 } appcModeOperSessLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the current session limit of this mode as negotiated through APPC CNOS (Change Number of Sessions) processing. Identifies the total number of sessions that can be established between the local and remote LU using this mode." ::= { appcModeOperEntry 7 } appcModeOperMaxSessLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum value that the local LU is to use, during CNOS processing, for the session limit. The local LU, as a target LU, will negotiate a higher session limit it receives in the CNOS Expires December 1994 [Page 52] Internet Draft APPC MIB July 18, 1994 request down to this maximum value. The local LU, as a source LU, will restrict the session limit it sends in a CNOS request to a value less than or equal to this maximum value." ::= { appcModeOperEntry 8 } appcModeOperConWinAutoActLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the limit on the number of contention winner sessions to be automatically activated when the minimum number of contention winner sessions increases (as a result of CNOS processing). The actual number of sessions activated is the lesser of this value and the new minimum number of contention winner sessions. " ::= { appcModeOperEntry 9 } appcModeOperDrainSelf OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the local LU is draining its conversations for this mode. Whan a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the local LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stopped or BIS protocol). " ::= { appcModeOperEntry 10 } appcModeOperDrainPart OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION Expires December 1994 [Page 53] Internet Draft APPC MIB July 18, 1994 "Specifies whether the remote LU is draining its conversations for this mode. Whan a mode session limit is reset (via a CNOS RESET_SESSION_LIMIT request), the remote LU could be set to process all queued conversations before deactivating all of the sessions (using the SNA Bracket Initiation Stop or BIS protocol). " ::= { appcModeOperEntry 11 } appcModeOperMinCwinLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the minimum contention winner sessions limit that was negotiated via CNOS processing." ::= { appcModeOperEntry 12 } appcModeOperMinClosLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the minimum contention loser sessions limit that was negotiated via CNOS processing." ::= { appcModeOperEntry 13 } appcModeOperRecvPacWinSz OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the size of the receive pacing window. This value is used for negotiation during session activations (SNA BIND)." ::= { appcModeOperEntry 14 } appcModeOperSendPacWinSz OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the size of the send pacing window. This value is Expires December 1994 [Page 54] Internet Draft APPC MIB July 18, 1994 used for negotiation during session activations (SNA BIND)." ::= { appcModeOperEntry 15 } appcModeOperPrefRecvRuSz OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the preferred receive RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeOperRecvRuSzUpBnd and greater than or equal to the value specified in appcModeOperRecvRuSzLoBnd. The local LU specifies this value for the receive maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeOperRecvRuSzUpBnd value or down to the appcModeOperRecvRuSzLoBnd value." ::= { appcModeOperEntry 16 } appcModeOperPrefSendRuSz OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the preferred send RU (Request Unit) size of normal-flow requests on the sessions. This value must be less than or equal to the value specified in appcModeOperSendRuSzUpBnd and greater than or equal to the value specified in appcModeOperSendRuSzLoBnd. The local LU specifies this value for the send maximum RU size in session activation (SNA BIND) requests and responses. It will allow negotiation up to the appcModeOperSendRuSzUpBnd value or down to the appcModeOperSendRuSzLoBnd value." ::= { appcModeOperEntry 17 } appcModeOperRecvRuSzUpBnd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION Expires December 1994 [Page 55] Internet Draft APPC MIB July 18, 1994 "Specifies the upper bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeOperEntry 18 } appcModeOperSendRuSzUpBnd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the upper bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeOperEntry 19 } appcModeOperRecvRuSzLoBnd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the lower bound for the maximum receive RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeOperEntry 20 } appcModeOperSendRuSzLoBnd OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the lower bound for the maximum send RU (Request Unit) size of normal-flow requests. This is used for negotiation during session activations (SNA BIND). " ::= { appcModeOperEntry 21 } appcModeOperDfSyncLvl OBJECT-TYPE SYNTAX INTEGER { none(1), noneConfirm(2), noneConfirmSyncPoint(3) } Expires December 1994 [Page 56] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the sync level support. This value is used for negotiation during session activations (SNA BIND). none - No sync level is supported. noneConfirm - None and Confirm level supported. noneConfirmSyncPoint - All sync level is supported. " ::= { appcModeOperEntry 22 } appcModeOperDfCrypto OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether cryptography is supported. This value is used for negotiation during session activations (SNA BIND)." ::= { appcModeOperEntry 23 } appcModeOperSingSessReinit OBJECT-TYPE SYNTAX INTEGER { operatorControlled(1), primaryOnly(2), secondaryOnly(3), primaryOrSecondary(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the responsibility for session reinitiation of a single session with the remote LU (when the session goes down). The local LU uses this parameter to specify the session reinitiation responsibility in session activation (SNA BIND) requests and responses. The value is only supported if the remote LU is defined to not support parallel sessions (i.e., appcInRluDefParaSessSup is set to no). operatorControlled - specifies that neither LU will Expires December 1994 [Page 57] Internet Draft APPC MIB July 18, 1994 automatically attempt to reinitiate the session. The operator on either side will manually reactivate the session. A contention race (both side reinitiating at the same time) is won by the LU with the lexigraphically greater fully-qualified LU name. primaryOnly - specifies that the primary LU will automatically attempt to reinitiate the session. secondaryOnly - specifies that the secondary LU will automatically attempt to reinitiate the session. primaryOrSecondary - specifies that either the primary or the secondary may automatically attempt to reinitiate the session. A contention race is handled the same way as with operatorControlled. " ::= { appcModeOperEntry 24 } appcModeOperAltCode OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether an alternate code is supported. yes - ASCII no - EBCDIC This value is used for negotiation during session activations (SNA BIND)." ::= { appcModeOperEntry 25 } appcModeOperCNOSNeg OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current Expires December 1994 [Page 58] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "Specifies whether CNOS negotiation is in process. CNOS negotiation is used to set or change the various session limits for a mode." ::= { appcModeOperEntry 26 } appcModeOperActSess OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the total number of currently active sessions between the local LU and the partner LU for this mode." ::= { appcModeOperEntry 27 } appcModeOperPndSess OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of pending sessions (waiting for session activation to complete." ::= { appcModeOperEntry 28 } appcModeOperActCwin OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of active contention winner sessions." ::= { appcModeOperEntry 29 } appcModeOperActClos OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of active contention loser sessions." ::= { appcModeOperEntry 30 } Expires December 1994 [Page 59] Internet Draft APPC MIB July 18, 1994 appcModeOperPndCwin OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of contention winner sessions that are pending activation." ::= { appcModeOperEntry 31 } appcModeOperPndClos OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of contention loser sessions that are pending activation." ::= { appcModeOperEntry 32 } appcModeOperPtmCwin OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of contention winner sessions that are pending termination." ::= { appcModeOperEntry 33 } appcModeOperPtmClos OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the number of contention loser sessions that are pending termination." ::= { appcModeOperEntry 34 } appcModeOperFreeSessLst OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION Expires December 1994 [Page 60] Internet Draft APPC MIB July 18, 1994 "Specifies the size of the free session list. This is the number of sessions that are available for conversations." ::= { appcModeOperEntry 35 } appcModeOperWaitReqLst OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the size of the waiting request list. This is the number of allocate requests that are waiting (queued) for an available session with this mode." ::= { appcModeOperEntry 36 } appcModeOperCompression OBJECT-TYPE SYNTAX INTEGER { prohibited(1), required(2), negotiable(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether compression is supported. The local LU uses this value for negotiation during session activation (SNA BIND). prohibited - specifies that no compression is to be used. required - specifies that compression is required. negotiable - specifies that the usage of compression is to be negotiated between the LU's. The level of compression is also negotiated." ::= { appcModeOperEntry 37 } appcModeOperInBoundCompLevel OBJECT-TYPE SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } Expires December 1994 [Page 61] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for inbound data. The local LU uses this value in conjunction with appcModeOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeOperEntry 38 } appcModeOperOutBoundCompLevel OBJECT-TYPE SYNTAX INTEGER { none(1), rle(2), lz9(3), lz10(4), lz12(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the maximum level of compression supported for outbound data. The local LU uses this value in conjunction with appcModeOperCompression for negotiation during session activation (SNA BIND). none - specifies that no compression is to be used. Expires December 1994 [Page 62] Internet Draft APPC MIB July 18, 1994 rle - specifies run-length encoding compression in which a 1 or 2 byte sequence substitution is used for each repeated run of the same character. lz9 - specifies Lempel-Ziv-like compression in which 9 bit codes are used to substitute repeated substrings in the data stream. These codes are indices that refer to entries in a common dictionary generated adaptively at both sender and receiver as the data flows and compression occurs. The larger of number bits used for the code, the more storage space is required for the dictionary, but the larger the compression ratio. lz10 - specifies a 10 bit code Lempel-Ziv-like compression. lz12 - specifies a 12 bit code Lempel-Ziv-like compression." ::= { appcModeOperEntry 39 } appcModeOperCompRleBeforeLZ OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether run-length encoding is to be applied to the data before applying Lempel-Ziv-like compression. The local LU uses this value for negotiation during session activation (SNA BIND). This parameter is only supported if LZ compression is used." ::= { appcModeOperEntry 40 } -- ********************************************************************* -- APPC TP Admin Table -- --------------------------------------------------------------------- -- This table contains information about configured remotely attachable -- transaction programs. -- ********************************************************************* appcTpAdminTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcTpAdminEntry MAX-ACCESS not-accessible STATUS current Expires December 1994 [Page 63] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "APPC Local TP Table" ::= { appcTp 1 } appcTpAdminEntry OBJECT-TYPE SYNTAX AppcTpAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC Local TP Information Table." INDEX { snaNodeAdminIndex, appcTpAdminIndex } ::= { appcTpAdminTable 1 } AppcTpAdminEntry ::= SEQUENCE { appcTpAdminIndex Integer32, appcTpAdminLocLuName DisplayString, appcTpAdminTpName DisplayString, appcTpAdminFileSpec DisplayString, appcTpAdminStartParm DisplayString, appcTpAdminTpOperation INTEGER, appcTpAdminQdepthLimit Gauge32, appcTpAdminInAttachTimeout Integer32, appcTpAdminRcvAllocTimeout Integer32, appcTpAdminDefType INTEGER, appcTpAdminSyncLvl INTEGER, appcTpAdminInstLmt Integer32, appcTpAdminStatus INTEGER, appcTpAdminLongRun INTEGER, appcTpAdminPfCnos INTEGER, appcTpAdminPfSessCntl INTEGER, appcTpAdminPfDefine INTEGER, appcTpAdminPfDisplay INTEGER, appcTpAdminPfAllocSer INTEGER, appcTpAdminConvType INTEGER, appcTpAdminConvSecReq INTEGER, appcTpAdminSecLvl INTEGER, appcTpAdminVerPip INTEGER, appcTpAdminPipSubNum INTEGER, appcTpAdminRowStatus RowStatus } Expires December 1994 [Page 64] Internet Draft APPC MIB July 18, 1994 appcTpAdminIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for entry in TP administrative table." ::= { appcTpAdminEntry 1 } appcTpAdminLocLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-create STATUS current DESCRIPTION "The SNA name of the local LU to which this TP definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. The reserved value '*ALL' indicates that the TP definition applies to all local LUs, and not just to a single local LU. Row creation conventions: When row creation is attempted, the agent must verify that the combination of requested local LU name and TP name is unique for the SNA node. If it is not, the agent must reject the attempt. Implementations that do not support definition of TPs on an LU-by-LU basis will reject any attempt to set this object to a value other than '*ALL'." ::= { appcTpAdminEntry 2 } appcTpAdminTpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "The local transaction program name. When the TP name consists entirely of displayable EBCDIC codepoints, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC codepoint (value less than or equal to x'3F') as the first character, so they cannot be directly Expires December 1994 [Page 65] Internet Draft APPC MIB July 18, 1994 mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC codepoints. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 4-byte ASCII display string '06F1'. Row creation conventions: When row creation is attempted, the agent must verify that the combination of requested local LU name and TP name is unique for the SNA node. If it is not, the agent must reject the attempt." ::= { appcTpAdminEntry 3 } appcTpAdminFileSpec OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) MAX-ACCESS read-create STATUS current DESCRIPTION "The local file specification of the transaction program. May be a zero-length string if not applicable." ::= { appcTpAdminEntry 4 } appcTpAdminStartParm OBJECT-TYPE SYNTAX DisplayString (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A parameter string passed to the transaction program when it is started. May be a zero-length string if not supported. " ::= { appcTpAdminEntry 5 } appcTpAdminTpOperation OBJECT-TYPE SYNTAX INTEGER { queuedOperatorStarted(1), queuedOperatorPreloaded(2), queuedAmStarted(3), nonqueuedAmStarted(4) } MAX-ACCESS read-create STATUS current DESCRIPTION Expires December 1994 [Page 66] Internet Draft APPC MIB July 18, 1994 "Specifies how the program will be started. queuedOperatorStarted -- Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, APPC will issue a message to the operator to start the specified program. Subsequent attaches that arrive while the program is active will be queued. queuedOperatorPreloaded -- Specifies that one version of the program will be run at a time. If an incoming attach arrives and the program has not been started yet, the Attach will be rejected. The APPC attach manager determines that a TP has started upon reception of an APPC RECEIVE_ALLOCATE verb or a CPI Communications program Accept_Conversation (CMACCP) call. No message is sent to the operator. Subsequent attaches that arrive while the program is active are queued. queuedAmStarted -- Specifies that one version of the program will be run at a time and will be started by the APPC attach manager. Subsequent attaches that arrive while the program is active will be queued. nonqueuedAmStarted -- Specifies that multiple copies of the program will be run at a time and will be started by the APPC attach manager." ::= { appcTpAdminEntry 6 } appcTpAdminQdepthLimit OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the number of incoming attaches that will be queued before being rejected. This parameter is meaningful only when appcTpAdminTpOperation has one of the following values: queuedOperatorStarted queuedOperatorPreloaded Expires December 1994 [Page 67] Internet Draft APPC MIB July 18, 1994 queuedAmStarted The object has a value of zero otherwise." ::= { appcTpAdminEntry 7 } appcTpAdminInAttachTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the number of seconds incoming attaches will be queued waiting for an APPC program to issue a RECEIVE_ALLOCATE verb or for a CPI Communications program to issue an Accept_Conversation (CMACCP) call. This parameter is meaningful only when appcTpAdminTpOperation has one of the following values: queuedOperatorStarted queuedOperatorPreloaded queuedAmStarted A value of zero indicates that there is no timeout." ::= { appcTpAdminEntry 8 } appcTpAdminRcvAllocTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "This object specifies the number of seconds an APPC program's RECEIVE_ALLOCATE verb or a CPI Communications program's Accept_Conversation (CMACCP) call will wait for an incoming attach to arrive. A value of zero indicates that there is no timeout." ::= { appcTpAdminEntry 9 } appcTpAdminDefType OBJECT-TYPE SYNTAX INTEGER { sysdef(1), dynamic(2) } Expires December 1994 [Page 68] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-create STATUS current DESCRIPTION "The TP definition type. Indicates whether the TP was specified in the nodes system definitions or was dynamically created to support an inbound attach." ::= { appcTpAdminEntry 10 } appcTpAdminSyncLvl OBJECT-TYPE SYNTAX INTEGER { none(1), confirm(2), noneAndConfirm(3), syncPoint(4), noneAndSyncPoint(5), confirmAndSyncPoint(6), all(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the synchronization level or levels that the transaction program supports. " ::= { appcTpAdminEntry 11 } appcTpAdminInstLmt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of concurrent instances of this transaction program that will be supported for a local LU. A value of zero indicates that there is no limit." ::= { appcTpAdminEntry 12 } appcTpAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), tempDisabled(2), permDisabled(3) } Expires December 1994 [Page 69] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-create STATUS current DESCRIPTION "The TP status." ::= { appcTpAdminEntry 14 } appcTpAdminLongRun OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The long running transaction program." ::= { appcTpAdminEntry 15 } appcTpAdminPfCnos OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The TP Change Number of Sessions (CNOS) privileged function. This parameter specifies whether or not this program is allowed to issue CNOS verbs." ::= { appcTpAdminEntry 16 } appcTpAdminPfSessCntl OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The TP Session Control privileged function. This parameter specifies whether or not this program is allowed to issue ACTIVATE_SESSION Expires December 1994 [Page 70] Internet Draft APPC MIB July 18, 1994 and DEACTIVATE_SESSION verbs." ::= { appcTpAdminEntry 17 } appcTpAdminPfDefine OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The TP Define privileged function. This parameter specifies whether or not this program is allowed to issue DEFINE and DELETE verbs." ::= { appcTpAdminEntry 18 } appcTpAdminPfDisplay OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The TP Display privileged function. This parameter specifies whether or not this program is allowed to issue DISPLAY verbs." ::= { appcTpAdminEntry 19 } appcTpAdminPfAllocSer OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The TP Allocate Service privileged function. This parameter specifies whether or not this program is allowed to issue the ALLOCATE verb with its TPN parameter specifying an SNA Expires December 1994 [Page 71] Internet Draft APPC MIB July 18, 1994 service transmission program." ::= { appcTpAdminEntry 20 } appcTpAdminConvType OBJECT-TYPE SYNTAX INTEGER { basic(1), mapped(2), basicOrMapped(3), fdxBasic(4), fdxMapped(5), fdxBasicOrFdxMapped(6), anyType(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the type (basic or mapped) and style (half-duplex or full-duplex) of conversations that will be used by the TP. This value is verified upon receipt of an incoming attach. The acceptable values are: basic -- Indicates that this transaction program supports basic conversations. mapped -- Indicates that this transaction program supports mapped conversations. basicOrMapped -- Indicates that this transaction program supports either basic or mapped conversations. fdxBasic -- Indicates that this transaction program supports basic conversation verbs for full-duplex operation. fdxMapped -- Indicates that this transaction program supports mapped conversation verbs for full-duplex operation. fdxBasicOrFdxMapped -- Indicates that this transaction program supports either basic or mapped conversation verbs for full-duplex operation. anyType -- Indicates that this transaction program supports either basic or mapped conversation Expires December 1994 [Page 72] Internet Draft APPC MIB July 18, 1994 verbs, and can accept either a half-duplex or full-duplex conversation, depending upon what arrives on the incoming allocation request. " ::= { appcTpAdminEntry 21 } appcTpAdminConvSecReq OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether conversation-level security information is required on incoming attaches designating this tp_name. Conversation-level security verification is always performed on those requests that include security information. yes -- Indicates that conversation-level security information is required. Attaches designating the transaction program must carry a user_id and either a password or an already verified indicator. no -- Indicates that no security information is required. Attaches designating the transaction program can omit or include security information. " ::= { appcTpAdminEntry 22 } appcTpAdminSecLvl OBJECT-TYPE SYNTAX INTEGER { noAdditional(1), specificUsers(2), specificProfiles(3), specificUserProfiles(4), specificUserLus(5), specificUserProfLus(6) } MAX-ACCESS read-create STATUS current Expires December 1994 [Page 73] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "The TP security level parameter." ::= { appcTpAdminEntry 23 } appcTpAdminVerPip OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The TP verify pip parameter." ::= { appcTpAdminEntry 24 } appcTpAdminPipSubNum OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The TP number of pip subfields." ::= { appcTpAdminEntry 25 } appcTpAdminRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used by a Management Station to create or delete the row entry in the appcTpAdminTable following the RowStatus textual convention. " ::= { appcTpAdminEntry 26 } Expires December 1994 [Page 74] Internet Draft APPC MIB July 18, 1994 -- ********************************************************************* -- APPC TP Oper Table -- --------------------------------------------------------------------- -- This table contains information about active transaction programs. -- ********************************************************************* appcTpOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcTpOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC Local TP Table" ::= { appcTp 2 } appcTpOperEntry OBJECT-TYPE SYNTAX AppcTpOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC Local TP Information Table." INDEX { snaNodeAdminIndex, snaLuAdminLuIndex, appcTpOperIndex } ::= { appcTpOperTable 1 } AppcTpOperEntry ::= SEQUENCE { appcTpOperIndex Integer32, appcTpOperAdminIndex Integer32, appcTpOperTpId DisplayString, appcTpOperLocLuName DisplayString, appcTpOperTpName DisplayString } appcTpOperIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for entry in TP Operational table." ::= { appcTpOperEntry 1 } Expires December 1994 [Page 75] Internet Draft APPC MIB July 18, 1994 appcTpOperAdminIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Index of entry in TP administrative table associated with this TP. If this TP was started up locally (i.e., not by an incoming FMH5 ATTACH), it may not have an associated admin entry. In this case, the index is set to 0." ::= { appcTpOperEntry 2 } appcTpOperTpId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The internal identifier of the transaction program." ::= { appcTpOperEntry 3 } appcTpOperLocLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the local LU associated with this active TP. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. This value is redundant, because the snaLuAdminLuIndex could be used to retrieve this value from the snaLuAdminTable, but the value is duplicated here to simplify management station application programming." ::= { appcTpOperEntry 4 } appcTpOperTpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The local transaction program name. Expires December 1994 [Page 76] Internet Draft APPC MIB July 18, 1994 When the TP name consists entirely of displayable EBCDIC codepoints, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC codepoint (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC codepoints. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 4-byte ASCII display string '06F1'. This value is redundant, because the appcTpOperAdminIndex could be used to retrieve this value from the appcTpAdminTable, but the value is duplicated here to simplify management station application programming. If appcTpOperAdminIndex is 0 (i.e., no entry in appcTpAdminTable), then this name is set to a NULL string." ::= { appcTpOperEntry 5 } -- ********************************************************************* -- APPC Session Table - only objects specific to APPC session are defined -- here. The generic objects are defined in snanau mib. -- --------------------------------------------------------------------- -- This table contains information about APPC sessions -- ********************************************************************* appcSessnTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcSessnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC Session Table" ::= { appcSession 1 } appcSessnEntry OBJECT-TYPE SYNTAX AppcSessnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC Session Information Table. Indexed as NAU MIB session table." INDEX { snaNodeAdminIndex, snaLuAdminLuIndex, snaLuSessnRluIndex, Expires December 1994 [Page 77] Internet Draft APPC MIB July 18, 1994 snaLuSessnIndex } ::= { appcSessnTable 1 } AppcSessnEntry ::= SEQUENCE { appcSessnPcidCpName DisplayString, appcSessnPcid OCTET STRING, appcSessnPluIndicator INTEGER, appcSessnLluName DisplayString, appcSessnModeName DisplayString, appcSessnCosName DisplayString, appcSessnTransPriority Integer32, appcSessnEnhanceSecSup INTEGER, appcSessnSendPacingType INTEGER, appcSessnSendRpc Gauge32, appcSessnSendNxWndwSize Gauge32, appcSessnRecvPacingType INTEGER, appcSessnRecvRpc Gauge32, appcSessnRecvNxWndwSize Gauge32, appcSessnUpTime TimeStamp, appcSessnCtrUpTime TimeStamp, appcSessnP2SFmdPius Counter32, appcSessnS2PFmdPius Counter32, appcSessnP2SNonFmdPius Counter32, appcSessnS2PNonFmdPius Counter32, appcSessnP2SFmdBytes Counter32, appcSessnS2PFmdBytes Counter32, appcSessnP2SNonFmdBytes Counter32, appcSessnS2PNonFmdBytes Counter32, appcSessnRscv OCTET STRING } appcSessnPcidCpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network-qualified CP name of the node at which the session and pcid originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcSessnEntry 1 } Expires December 1994 [Page 78] Internet Draft APPC MIB July 18, 1994 appcSessnPcid OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The procedure correlation identifier (pcid) of a session. It is an 8-octet value assigned by the primary LU." ::= { appcSessnEntry 2 } appcSessnPluIndicator OBJECT-TYPE SYNTAX INTEGER { localLuIsPlu(1), remoteLuIsPlu(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates which LU is the PLU for this session. For independent LUs, the PLU (primary LU) is the one that initiated the session (sent BIND), while the SLU (secondary LU) is the one that accepted the session initiation (received BIND). The 'local' LU is the one identified by snaLuAdminLuIndex and by appcSessnLluName. The 'remote' LU is the one identified by snaLuSessnRluIndex and by snaLuSessnRemoteLuName." ::= { appcSessnEntry 3 } appcSessnLluName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the local LU for this session. This is the LU identified by snaLuAdminIndex. It is included here for convenience only (also accessible as snaLuAdminSnaName using snaLuAdminIndex). This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcSessnEntry 4 } Expires December 1994 [Page 79] Internet Draft APPC MIB July 18, 1994 appcSessnModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The mode name name used for this session." ::= { appcSessnEntry 5 } appcSessnCosName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Class of Service (COS) name used for this session." ::= { appcSessnEntry 6 } appcSessnTransPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The transmission priority of this session." ::= { appcSessnEntry 7 } appcSessnEnhanceSecSup OBJECT-TYPE SYNTAX INTEGER { none(1), level1(2), level2(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Enhanced security supported. Indicates the level of enhanced security support: 1 = none 2 = level 1 3 = level 2 " ::= { appcSessnEntry 8 } Expires December 1994 [Page 80] Internet Draft APPC MIB July 18, 1994 appcSessnSendPacingType OBJECT-TYPE SYNTAX INTEGER { none(1), fixed(2), adaptive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of pacing being used for sending data." ::= { appcSessnEntry 9 } appcSessnSendRpc OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The send residual pace count. This represents the number of MU's that can still be sent in the current session window." ::= { appcSessnEntry 10 } appcSessnSendNxWndwSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the next window which will be used to send data." ::= { appcSessnEntry 11 } appcSessnRecvPacingType OBJECT-TYPE SYNTAX INTEGER { none(1), fixed(2), adaptive(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of pacing being used for receiving data." ::= { appcSessnEntry 12 } Expires December 1994 [Page 81] Internet Draft APPC MIB July 18, 1994 appcSessnRecvRpc OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The receive residual pace count. This represents the number of MU's that can still be received in the current session window." ::= { appcSessnEntry 13 } appcSessnRecvNxWndwSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The size of the next window which will be used to receive data." ::= { appcSessnEntry 14 } appcSessnUpTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Length of time the session has been up in hundreds of a second. This is the elapsed time since the session started (snaLuSessnActiveTime)." ::= { appcSessnEntry 15 } appcSessnCtrUpTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Length of time the session counters have been active in hundreds of a second. This value is included for implementations that allow an operator or management workstation to enable and disable the collection of session statistics. For implementations that do not provide that option, i.e., counters are always enabled, this value will be the same as appcSessnUpTime." ::= { appcSessnEntry 16 } Expires December 1994 [Page 82] Internet Draft APPC MIB July 18, 1994 appcSessnP2SFmdPius OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD PIUs sent from the Primary LU to the Secondary LU. This value differs from snaLuSessnStatsReceivedRus, which counts both FM data RUs and control RUs. This counter is just for FM data." ::= { appcSessnEntry 17 } appcSessnS2PFmdPius OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD PIUs sent from the Secondary LU to the Primary LU. This value differs from snaLuSessnStatsSentRus, which counts both FM data RUs and control RUs. This counter is just for FM data." ::= { appcSessnEntry 18 } appcSessnP2SNonFmdPius OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD PIUs sent from the Primary LU to the Secondary LU" ::= { appcSessnEntry 19 } appcSessnS2PNonFmdPius OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD PIUs sent from the Secondary LU to the Primary LU" ::= { appcSessnEntry 20 } appcSessnP2SFmdBytes OBJECT-TYPE Expires December 1994 [Page 83] Internet Draft APPC MIB July 18, 1994 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD Bytes sent from the Primary LU to the Secondary LU" ::= { appcSessnEntry 21 } appcSessnS2PFmdBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of FMD Bytes sent from the Secondary LU to the Primary LU" ::= { appcSessnEntry 22 } appcSessnP2SNonFmdBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD Bytes sent from the Primary LU to the Secondary LU" ::= { appcSessnEntry 23 } appcSessnS2PNonFmdBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of non-FMD Bytes sent from the Secondary LU to the Primary LU" ::= { appcSessnEntry 24 } appcSessnRscv OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The route selection control vector (RSCV CV2B) used for this Expires December 1994 [Page 84] Internet Draft APPC MIB July 18, 1994 session. It is present for APPN-level implementations. LEN-level implementations will return a null string. The internal format of this vector is described in SNA Formats. This object contains an un-interpreted copy of the control vector (including the length and key fields)." ::= { appcSessnEntry 25 } -- ********************************************************************* -- APPC Conversation Table -- --------------------------------------------------------------------- -- This table contains information about active and inactive APPC -- conversations. This table represents a historical log of conversations. -- Since some conversations could be very dynamic and can come up and down -- relatively quickly, we felt it might be more useful if this table showed -- not only active conversations, but those that became inactive. However, -- this could also mean that the number of entries could get pretty big. -- So, this does present some issues with regard to how the older entries get -- removed: -- 1) Should we use an aging mechanism so that older entries automatically -- get deleted? -- 2) Should we have have a maximum number of entries and once it is -- exceeded, oldest entries are automatically reused? Should we specify -- the maximum or should it be implemention dependent? -- 3) Should we have objects to manage this table (e.g., delete entries)? -- 4) Is it worth the added complexity to make this table show historical -- information? -- ********************************************************************* appcConvTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcConvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of APPC Conversations" ::= { appcConversation 1 } appcConvEntry OBJECT-TYPE SYNTAX AppcConvEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC Conversation Table." Expires December 1994 [Page 85] Internet Draft APPC MIB July 18, 1994 INDEX { snaNodeAdminIndex, snaLuAdminLuIndex, appcTpOperIndex, appcConvIndex } ::= { appcConvTable 1} AppcConvEntry ::= SEQUENCE { appcConvIndex Integer32, appcConvId OCTET STRING, appcConvState INTEGER, appcConvType INTEGER, appcConvCorrelator OCTET STRING, appcConvSyncLvl INTEGER, appcConvSource INTEGER, appcConvStyle INTEGER, appcConvStartTime TimeStamp, appcConvStopTime TimeStamp, appcConvSendBytes Counter32, appcConvRcvBytes Counter32, appcConvUserid DisplayString, appcConvPcidNauName DisplayString, appcConvPcid String, appcConvModeName DisplayString, appcConvLuwIdName DisplayString, appcConvLuwIdInstance String, appcConvLuwIdSequence String, appcConvTpName DisplayString, appcConvSessnIndex Integer32 } appcConvIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index for entry in Conversation table." ::= { appcConvEntry 1 } appcConvId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-only STATUS current Expires December 1994 [Page 86] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "The 4-byte ID of the conversation." ::= { appcConvEntry 2 } appcConvState OBJECT-TYPE SYNTAX INTEGER { reset(1), send(2), receive(3), confirm(4), confirmSend(5), confirmDealloc(6), pendingDeallocate(7), pendingPost(8), sendReceive(9), sendOnly(10), receiveOnly(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the state of the conversation at the instant when the information was retrieved. The values are: reset The conversation is reset (i.e., deallocated). send The conversation can send data. This value also is returned if the conversation is in Send-Pending state. receive The conversation can receive data. confirm The conversation has received a confirm indicator. It can issue an [MC_]CONFIRMED or [MC_]SEND_ERROR verb to change state. It will continue in Receive state if an [MC_]CONFIRMED verb is issued. confirmSend The conversation is in Confirm state and changes to Send state when an [MC_]CONFIRMED verb is Expires December 1994 [Page 87] Internet Draft APPC MIB July 18, 1994 issued. confirmDealloc The conversation is in Confirm state and becomes inactive when an [MC_]CONFIRMED verb is issued. pendingDeallocate The conversation is in Pending-Deallocate state while it waits for (MC_)DEALLOCATE TYPE (sync_level) to complete. pendingPost The conversation is in Pending-Post state while it waits for the [MC_]RECEIVE_AND_POST verb to complete its receive function. sendReceive The full-duplex conversation can send or receive data. sendOnly The full-duplex conversation can send data, but it does not have permission to receive data, because the partner TP has already deallocated its side of the conversation. receiveOnly The full-duplex conversation can receive data, but it does not have permission to send data, because it has already deallocated its side of the conversation. " ::= { appcConvEntry 3 } appcConvType OBJECT-TYPE SYNTAX INTEGER { basic(1), mapped(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of conversation. The values are: basic Expires December 1994 [Page 88] Internet Draft APPC MIB July 18, 1994 Indicates that this conversation supports basic verbs. mapped Indicates that this conversation supports mapped verbs." ::= { appcConvEntry 4 } appcConvCorrelator OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is an 8-byte identifier that the source LU assigns to the conversation; the source LU is the one that sent the allocation request. The conversation correlator is included on the allocation request. The conversation correlator uniquely identifies a conversation, from among all conversations, between the local and partner LUs. It may be used, for example, during problem determination associated with a conversation. A length of 0 indicates that no conversation correlator is defined." ::= { appcConvEntry 5 } appcConvSyncLvl OBJECT-TYPE SYNTAX INTEGER { none(1), confirm(2), syncpt(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the highest sync level support for the conversation. The values are: none Indicates that no sync-level processing can be performed on this conversation. The transaction program does not issue verbs or recognize any returned parameters relating to any sync-level function. Expires December 1994 [Page 89] Internet Draft APPC MIB July 18, 1994 confirm Indicates that confirmation processing can be performed on this conversation. The transaction program can issue verbs and recognize returned parameters relating to confirmation. syncpt Indicates that syncpt and confirmation processing can be performed on this conversation. The transaction program can issue verbs and recognize returned parameters relating to syncpt and confirmation." ::= { appcConvEntry 6 } appcConvSource OBJECT-TYPE SYNTAX INTEGER { localLu(1), partnerLu(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the local or partner LU is the source of the conversation, that is, which LU started the conversation by sending the allocation request. localLu The local LU is the source of the conversation, and the partner LU is the target of the conversation. partnerLu The partner LU is the source of the conversation, and the local LU is the target of the conversation." ::= { appcConvEntry 7 } appcConvStyle OBJECT-TYPE SYNTAX INTEGER { twoWayAlternate(1), twoWaySimultaneous(2) } Expires December 1994 [Page 90] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the conversation style in effect for the conversation. twoWayAlternate Indicates that information is transferred in both directions, but only in one direction at a time. This style of data transfer is also known as half-duplex conversation. twoWaySimultaneous Indicates that information is transferred in both directions at the same time. This style of data transfer is also known as full-duplex conversation." ::= { appcConvEntry 8 } appcConvStartTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the conversation started in hundreds of a second." ::= { appcConvEntry 9 } appcConvStopTime OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "Time when the conversation stopped in hundreds of a second." ::= { appcConvEntry 10 } appcConvSendBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of bytes that was sent on the conversation. The count includes all SNA RU bytes sent, including those in the Expires December 1994 [Page 91] Internet Draft APPC MIB July 18, 1994 FMH-5 (Attach), FMH-7 (Error Description), SIGNAL, LUSTAT, and SNA responses; it does not include SNA TH and RH bytes." ::= { appcConvEntry 11 } appcConvRcvBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of bytes that was received on the conversation. The count includes all SNA RU bytes sent, including those in the FMH-5 (Attach), FMH-7 (Error Description), SIGNAL, LUSTAT, and SNA responses; it does not include SNA TH and RH bytes." ::= { appcConvEntry 12 } appcConvUserid OBJECT-TYPE SYNTAX DisplayString (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The user ID that the initiating program provided in the incoming attach." ::= { appcConvEntry 13 } appcConvPcidNauName OBJECT-TYPE SYNTAX DisplayString (SIZE (3..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The network-qualified NAU name or of the node at which the session and pcid originated. For APPN and LEN nodes, this is either CP name of the APPN node at which the origin LU is located or the CP name of the NN serving the LEN node at which the origin LU is located. This field is from 3 to 17 characters in length, including a period (.) which separates the NetId from the NAU name." ::= { appcConvEntry 14 } appcConvPcid OBJECT-TYPE Expires December 1994 [Page 92] Internet Draft APPC MIB July 18, 1994 SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The procedure correlation identifier (pcid) of the session. It is an 8-octet value assigned by the primary LU." ::= { appcConvEntry 15 } appcConvModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Mode Name name used for this conversation. This is a 1-8 character name." ::= { appcConvEntry 16 } appcConvLuwIdName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the LU that initiated the logical unit of work that is associated with this active TP. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the LU name if the netId is present." ::= { appcConvEntry 17 } appcConvLuwIdInstance OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..6)) MAX-ACCESS read-only STATUS current DESCRIPTION "The instance identifier for the logical unit of work." ::= { appcConvEntry 18 } appcConvLuwIdSequence OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..2)) MAX-ACCESS read-only STATUS current DESCRIPTION Expires December 1994 [Page 93] Internet Draft APPC MIB July 18, 1994 "The sequence identifier for the logical unit of work." ::= { appcConvEntry 19 } appcConvTpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The transaction program name from the FMH5 ATTACH which started this conversation. When the TP name consists entirely of displayable EBCDIC codepoints, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC codepoint (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC codepoints. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 4-byte ASCII display string '06F1'." ::= { appcConvEntry 20 } appcConvSessnIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Index of entry in appcSessnTable that is associated with this conversation. If the conversation is reset, then this value is set to 0." ::= { appcConvEntry 21 } -- ********************************************************************* -- APPC CPIC Admin Table -- ********************************************************************* appcCpicAdminTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcCpicAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC CPI-C side information table." Expires December 1994 [Page 94] Internet Draft APPC MIB July 18, 1994 ::= { appcCPIC 1 } appcCpicAdminEntry OBJECT-TYPE SYNTAX AppcCpicAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC CPI-C side information Table." INDEX { appcCpicAdminIndex } ::= { appcCpicAdminTable 1 } AppcCpicAdminEntry ::= SEQUENCE { appcCpicAdminIndex Integer32, appcCpicAdminLocLuName DisplayString, appcCpicAdminSymbDestName DisplayString, appcCpicAdminParLuAlias DisplayString, appcCpicAdminParLuName DisplayString, appcCpicAdminModeName DisplayString, appcCpicAdminTpNameType INTEGER, appcCpicAdminTpName DisplayString, appcCpicAdminUserid DisplayString, appcCpicAdminRowStatus RowStatus } appcCpicAdminIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index to the table of CPI-C side information. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcCpicAdminEntry 1 } appcCpicAdminLocLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-create STATUS current DESCRIPTION "The SNA name of the local LU to which this CPI-C side Expires December 1994 [Page 95] Internet Draft APPC MIB July 18, 1994 information definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. The reserved value '*ALL' indicates that the definition applies to all local LUs, and not just to a single local LU. Row creation conventions: When row creation is attempted, the agent must verify that the combination of local LU name and symbolic destination name is unique for the SNA node, i.e., the values in the newly created row must not conflict with an existing definition. If they do conflict, the agent must reject the attempt to create the new row. Implementations that do not support definition of CPI-C side information on an LU by LU basis will reject any attempt to set this object to a value other than '*ALL'." ::= { appcCpicAdminEntry 2 } appcCpicAdminSymbDestName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the symbolic destination name used by CPI-C applications to identify this definition." ::= { appcCpicAdminEntry 3 } appcCpicAdminParLuAlias OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string." ::= { appcCpicAdminEntry 4 } appcCpicAdminParLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) Expires December 1994 [Page 96] Internet Draft APPC MIB July 18, 1994 MAX-ACCESS read-create STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcCpicAdminEntry 5 } appcCpicAdminModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). Row creation conventions: If the desired mode name is the default blank mode name, the appcCpicAdminModeName object must be set to the reserved value 'BLANK', which represents the value of 8 space characters operationally. A set with a shorter string of space characters will be padded to 8 spaces by the agent. Display convention A get operation against this object will return the string 'BLANK' if the actual value is 8 spaces. This convention is intended to prevent operator confusion and is consistent with the practice of some existing implementations. " ::= { appcCpicAdminEntry 6 } appcCpicAdminTpNameType OBJECT-TYPE SYNTAX INTEGER { normal(1), snaServiceTp(2) } MAX-ACCESS read-create Expires December 1994 [Page 97] Internet Draft APPC MIB July 18, 1994 STATUS current DESCRIPTION "Specifies whether the tp name in appcCpicAdminTpName identifies a normal TP or an SNA service TP. In this context, a normal TP is one with a name consisting only of displayable characters, while an SNA service TP has a name containing octets that do not map to displayable characters." ::= { appcCpicAdminEntry 7 } appcCpicAdminTpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the name of the partner TP to be used when a CPI-C application initiates a conversation specifying this side information entry. Row creation conventions: For a 'normal' TP name (displayable string), the default value of appcCpicAdminTpNameType is acceptable, and the management station sets appcCpicAdminTpName to the desired value (a display string equivalent to the EBCDIC TP name). For a 'snaServiceTp' TP name (non-displayable string), the management station must set appcCpicAdminTpNameType to the value snaServiceTp BEFORE setting appcCpicAdminTpName to the desired value. When appcCpicAdminTpNameType has the value snaServiceTp, the management station will follow the display convention described below when it sets the TP name. The agent system will then interpret the string as equivalent to a hexadecimal display of the EBCDIC codepoints. Display convention When the TP name consists entirely of displayable EBCDIC codepoints, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC codepoint (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a Expires December 1994 [Page 98] Internet Draft APPC MIB July 18, 1994 hexadecimal display of the EBCDIC codepoints. For example, the 2-byte TP name x'06F1' (CNOS) is converted to the 4-byte ASCII display string '06F1'." ::= { appcCpicAdminEntry 8 } appcCpicAdminUserid OBJECT-TYPE SYNTAX DisplayString (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The security userid, if any, associated with the side information definition." ::= { appcCpicAdminEntry 9 } appcCpicAdminRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used by a Management Station to create or delete the row entry in the appcCpicAdminTable following the RowStatus textual convention. " ::= { appcCpicAdminEntry 10 } -- ********************************************************************* -- APPC CPIC Oper Table -- ********************************************************************* appcCpicOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AppcCpicOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "APPC CPI-C side information table." ::= { appcCPIC 2 } appcCpicOperEntry OBJECT-TYPE Expires December 1994 [Page 99] Internet Draft APPC MIB July 18, 1994 SYNTAX AppcCpicOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry of APPC CPI-C side information Table." INDEX { appcCpicOperIndex } ::= { appcCpicOperTable 1 } AppcCpicOperEntry ::= SEQUENCE { appcCpicOperIndex Integer32, appcCpicOperLocLuName DisplayString, appcCpicOperSymbDestName DisplayString, appcCpicOperParLuAlias DisplayString, appcCpicOperParLuName DisplayString, appcCpicOperModeName DisplayString, appcCpicOperTpNameType INTEGER, appcCpicOperTpName DisplayString, appcCpicOperUserid DisplayString } appcCpicOperIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index to the table of CPI-C side information. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcCpicOperEntry 1 } appcCpicOperLocLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the local LU to which this CPI-C side information definition applies. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present. Expires December 1994 [Page 100] Internet Draft APPC MIB July 18, 1994 The reserved value '*ALL' indicates that the definition applies to all local LUs, and not just to a single local LU." ::= { appcCpicOperEntry 2 } appcCpicOperSymbDestName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the symbolic destination name used by CPI-C applications to identify this definition." ::= { appcCpicOperEntry 3 } appcCpicOperParLuAlias OBJECT-TYPE SYNTAX DisplayString (SIZE (0..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "A local alias for the partner LU. If not known or not applicable, this object contains a zero-length string." ::= { appcCpicOperEntry 4 } appcCpicOperParLuName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..17)) MAX-ACCESS read-only STATUS current DESCRIPTION "The SNA name of the partner LU. This field is from 1 to 17 characters in length, including a period (.) which separates the NetId from the NAU name if the netId is present." ::= { appcCpicOperEntry 5 } appcCpicOperModeName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..8)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the mode name. A mode defines the characteristics for a group of sessions. The mode name can be blank (8 space characters). Expires December 1994 [Page 101] Internet Draft APPC MIB July 18, 1994 Display convention A get operation against this object will return the string 'BLANK' if the actual value is 8 spaces. This convention is intended to prevent operator confusion and is consistent with the practice of some existing implementations. " ::= { appcCpicOperEntry 6 } appcCpicOperTpNameType OBJECT-TYPE SYNTAX INTEGER { normal(1), snaServiceTp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the tp name in appcCpicOperTpName identifies a normal TP or an SNA service TP. In this context, a normal TP is one with a name consisting only of displayable characters, while an SNA service TP has a name containing octets that do not map to displayable characters." ::= { appcCpicOperEntry 7 } appcCpicOperTpName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the name of the partner TP to be used when a CPI-C application initiates a conversation specifying this side information entry. Display convention When the TP name consists entirely of displayable EBCDIC codepoints, it is mapped directly to the equivalent ASCII display string. However, registered TP names always have a non-displayable EBCDIC codepoint (value less than or equal to x'3F') as the first character, so they cannot be directly mapped to an ASCII display string. These TP names are converted to a display string that is equivalent to a hexadecimal display of the EBCDIC codepoints. For Expires December 1994 [Page 102] Internet Draft APPC MIB July 18, 1994 example, the 2-byte TP name x'06F1' (CNOS) is converted to the 4-byte ASCII display string '06F1'." ::= { appcCpicOperEntry 8 } appcCpicOperUserid OBJECT-TYPE SYNTAX DisplayString (SIZE (0..10)) MAX-ACCESS read-only STATUS current DESCRIPTION "The security userid, if any, associated with the active side information definition." ::= { appcCpicOperEntry 9 } -- *************************************************************** -- Conformance information -- *************************************************************** appcConformance OBJECT IDENTIFIER ::= {appcMIB 2 } appcCompliances OBJECT IDENTIFIER ::= {appcConformance 1 } appcGroups OBJECT IDENTIFIER ::= {appcConformance 2 } -- Compliance statements appcCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for the SNMPv2 entities which implement the APPC MIB." MODULE -- this module -- Unconditionally mandatory groups MANDATORY-GROUPS { appcGlobalGroup, appcDefaultGroup, appcLluGroup, appcParLuGroup, appcModeGroup, appcTpGroup, appcSessionGroup, appcConversationGroup } -- Conditionally mandatory groups GROUP appcStatControlGroup Expires December 1994 [Page 103] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "The appcStatControlGroup is mandatory only for those entities which implement activation and deactivation of statistics collecting and counting." GROUP appcCpicGroup DESCRIPTION "The appcCpicGroup is mandatory only for those entities which implement CPI-C. " -- Refinement of requirements for objects access. -- The Agent which does not implement row creation for -- appcDefaultTable, appcParLuAdminTable, appcModeAdminTable, -- appcTpAdminTable, and appcCpicAdminTable must at least accept -- objects modification (read-write access instead of read-create). -- appcDefaultTable OBJECT appcDefaultModeName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcDefaultLuAlias MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcDefaultImplInbndPlu MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcDefaultMaxMcLlSndSize MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcDefaultFileSpec MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write Expires December 1994 [Page 104] Internet Draft APPC MIB July 18, 1994 access to this object." OBJECT appcDefaultTpOperation MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcDefaultTpConvSecRqd MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." -- appcParLuAdminTable OBJECT appcParLuAdminLocLuName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminParLuName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminAlias MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminDefType MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminDefParaSessSup MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." Expires December 1994 [Page 105] Internet Draft APPC MIB July 18, 1994 OBJECT appcParLuAdminDefCnosSup MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminDefSessSec MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminDefConvSec MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminDefAlVerSup MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcParLuAdminLinkName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." -- appcModeAdminTable OBJECT appcModeAdminModeName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminLocLuName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminParLuName Expires December 1994 [Page 106] Internet Draft APPC MIB July 18, 1994 MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminCosName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminDefType MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminSessEndTpName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminMaxSessLimit MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminConWinAutoActLimit MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminAdaptivePacing MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminRecvPacWinSz MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write Expires December 1994 [Page 107] Internet Draft APPC MIB July 18, 1994 access to this object." OBJECT appcModeAdminSendPacWinSz MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminPrefRecvRuSz MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminPrefSendRuSz MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminRecvRuSzUpBnd MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminSendRuSzUpBnd MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminRecvRuSzLoBnd MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminSendRuSzLoBnd MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminDfSyncLvl Expires December 1994 [Page 108] Internet Draft APPC MIB July 18, 1994 MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminDfCrypto MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminSingSessReinit MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminAltCode MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminCompression MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminInBoundCompLevel MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminOutBoundCompLevel MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcModeAdminCompRleBeforeLZ MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write Expires December 1994 [Page 109] Internet Draft APPC MIB July 18, 1994 access to this object." -- appcTpAdminTable OBJECT appcTpAdminLocLuName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminTpName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminFileSpec MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminStartParm MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminTpOperation MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminQdepthLimit MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminInAttachTimeout MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." Expires December 1994 [Page 110] Internet Draft APPC MIB July 18, 1994 OBJECT appcTpAdminRcvAllocTimeout MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminDefType MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminSyncLvl MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminInstLmt MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminStatus MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminLongRun MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminPfCnos MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminPfSessCntl MIN-ACCESS read-write DESCRIPTION Expires December 1994 [Page 111] Internet Draft APPC MIB July 18, 1994 "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminPfDefine MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminPfDisplay MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminPfAllocSer MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminConvType MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminConvSecReq MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminSecLvl MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcTpAdminVerPip MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." Expires December 1994 [Page 112] Internet Draft APPC MIB July 18, 1994 OBJECT appcTpAdminPipSubNum MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." -- appcCpicAdminTable OBJECT appcCpicAdminLocLuName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcCpicAdminSymbDestName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcCpicAdminParLuAlias MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcCpicAdminParLuName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcCpicAdminModeName MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcCpicAdminTpNameType MIN-ACCESS read-write DESCRIPTION "An Agent is required to implement read-write access to this object." OBJECT appcCpicAdminTpName MIN-ACCESS read-write Expires December 1994 [Page 113] Internet Draft APPC MIB July 18, 1994 DESCRIPTION "An Agent is required to implement read-write access to this object." ::= {appcCompliances 1 } -- Units of conformance appcGlobalGroup OBJECT-GROUP OBJECTS { appcNbLocLUInUse, appcNbSessnInUse } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC global information." ::= { appcGroups 1 } appcStatControlGroup OBJECT-GROUP OBJECTS { appcStatCntrlStatus, appcStatCntrlRscv, appcStatCntrlRscvTime, appcStatCntrlCtrStatus, appcStatCntrlCtrStatusTime } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC statistic collection and counting" ::= { appcGroups 2 } appcDefaultGroup OBJECT-GROUP OBJECTS { appcDefaultModeName, appcDefaultLuAlias, appcDefaultImplInbndPlu, appcDefaultMaxMcLlSndSize, appcDefaultFileSpec, appcDefaultTpOperation, appcDefaultTpConvSecRqd } STATUS current DESCRIPTION "A collection of objects providing the Expires December 1994 [Page 114] Internet Draft APPC MIB July 18, 1994 instrumentation of APPC Defaults." ::= { appcGroups 3 } appcLluGroup OBJECT-GROUP OBJECTS { appcLluOperDefType, appcLluOperSessLimit, appcLluOperBindRspMayQ, appcLluOperDefaultLu, appcLluOperCPlu } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC local LU6.2s." ::= { appcGroups 4 } appcParLuGroup OBJECT-GROUP OBJECTS { appcParLuAdminLocLuName, appcParLuAdminParLuName, appcParLuAdminAlias, appcParLuAdminDefType, appcParLuAdminDefParaSessSup, appcParLuAdminDefCnosSup, appcParLuAdminDefSessSec, appcParLuAdminDefConvSec, appcParLuAdminDefAlVerSup, appcParLuAdminLinkName, appcParLuAdminRowStatus, appcParLuOperLocLuName, appcParLuOperParLuName, appcParLuOperParLuAlias, appcParLuOperState, appcParLuOperActParaSessSup, appcParLuOperActCnosSup, appcParLuOperActSessSec, appcParLuOperActConvSec, appcParLuOperActAlVerSup, appcParLuOperLinkName } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC partner LUs." Expires December 1994 [Page 115] Internet Draft APPC MIB July 18, 1994 ::= { appcGroups 5 } appcModeGroup OBJECT-GROUP OBJECTS { appcModeAdminModeName, appcModeAdminLocLuName, appcModeAdminParLuName, appcModeAdminCosName, appcModeAdminDefType, appcModeAdminSessEndTpName, appcModeAdminMaxSessLimit, appcModeAdminConWinAutoActLimit, appcModeAdminAdaptivePacing, appcModeAdminRecvPacWinSz, appcModeAdminSendPacWinSz, appcModeAdminPrefRecvRuSz, appcModeAdminPrefSendRuSz, appcModeAdminRecvRuSzUpBnd, appcModeAdminSendRuSzUpBnd, appcModeAdminRecvRuSzLoBnd, appcModeAdminSendRuSzLoBnd, appcModeAdminDfSyncLvl, appcModeAdminDfCrypto, appcModeAdminSingSessReinit, appcModeAdminAltCode, appcModeAdminCompression, appcModeAdminInBoundCompLevel, appcModeAdminOutBoundCompLevel, appcModeAdminCompRleBeforeLZ, appcModeAdminRowStatus, appcModeOperLluName, appcModeOperRluName, appcModeOperModeName, appcModeOperCosName, appcModeOperDefType, appcModeOperSessEndTpName, appcModeOperSessLimit, appcModeOperMaxSessLimit, appcModeOperConWinAutoActLimit, appcModeOperDrainSelf, appcModeOperDrainPart, appcModeOperMinCwinLimit, appcModeOperMinClosLimit, appcModeOperRecvPacWinSz, appcModeOperSendPacWinSz, Expires December 1994 [Page 116] Internet Draft APPC MIB July 18, 1994 appcModeOperPrefRecvRuSz, appcModeOperPrefSendRuSz, appcModeOperRecvRuSzUpBnd, appcModeOperSendRuSzUpBnd, appcModeOperRecvRuSzLoBnd, appcModeOperSendRuSzLoBnd, appcModeOperDfSyncLvl, appcModeOperDfCrypto, appcModeOperSingSessReinit, appcModeOperAltCode, appcModeOperCNOSNeg, appcModeOperActSess, appcModeOperPndSess, appcModeOperActCwin, appcModeOperActClos, appcModeOperPndCwin, appcModeOperPndClos, appcModeOperPtmCwin, appcModeOperPtmClos, appcModeOperFreeSessLst, appcModeOperWaitReqLst, appcModeOperCompression, appcModeOperInBoundCompLevel, appcModeOperOutBoundCompLevel, appcModeOperCompRleBeforeLZ } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC modes." ::= { appcGroups 6 } appcTpGroup OBJECT-GROUP OBJECTS { appcTpAdminLocLuName, appcTpAdminTpName, appcTpAdminFileSpec, appcTpAdminStartParm, appcTpAdminTpOperation, appcTpAdminQdepthLimit, appcTpAdminInAttachTimeout, appcTpAdminRcvAllocTimeout, appcTpAdminDefType, appcTpAdminSyncLvl, appcTpAdminInstLmt, Expires December 1994 [Page 117] Internet Draft APPC MIB July 18, 1994 appcTpAdminStatus, appcTpAdminLongRun, appcTpAdminPfCnos, appcTpAdminPfSessCntl, appcTpAdminPfDefine, appcTpAdminPfDisplay, appcTpAdminPfAllocSer, appcTpAdminConvType, appcTpAdminConvSecReq, appcTpAdminSecLvl, appcTpAdminVerPip, appcTpAdminPipSubNum, appcTpAdminRowStatus, appcTpOperTpId, appcTpOperLocLuName, appcTpOperTpName } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC Transaction Programs." ::= { appcGroups 7 } appcSessionGroup OBJECT-GROUP OBJECTS { appcSessnPcidCpName, appcSessnPcid, appcSessnPluIndicator, appcSessnLluName, appcSessnModeName, appcSessnCosName, appcSessnTransPriority, appcSessnEnhanceSecSup, appcSessnSendPacingType, appcSessnSendRpc, appcSessnSendNxWndwSize, appcSessnRecvPacingType, appcSessnRecvRpc, appcSessnRecvNxWndwSize, appcSessnUpTime, appcSessnCtrUpTime, appcSessnP2SFmdPius, appcSessnS2PFmdPius, appcSessnP2SNonFmdPius, appcSessnS2PNonFmdPius, Expires December 1994 [Page 118] Internet Draft APPC MIB July 18, 1994 appcSessnP2SFmdBytes, appcSessnS2PFmdBytes, appcSessnP2SNonFmdBytes, appcSessnS2PNonFmdBytes, appcSessnRscv } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC LU6.2 sessions." ::= { appcGroups 8 } appcConversationGroup OBJECT-GROUP OBJECTS { appcConvId, appcConvState, appcConvType, appcConvCorrelator, appcConvSyncLvl, appcConvSource, appcConvStyle, appcConvStartTime, appcConvStopTime, appcConvSendBytes, appcConvRcvBytes, appcConvUserid, appcConvPcidNauName, appcConvPcid, appcConvModeName, appcConvLuwIdName, appcConvLuwIdInstance, appcConvLuwIdSequence, appcConvTpName, appcConvSessnIndex } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC conversations." ::= { appcGroups 9 } appcCpicGroup OBJECT-GROUP OBJECTS { appcCpicAdminLocLuName, appcCpicAdminSymbDestName, Expires December 1994 [Page 119] Internet Draft APPC MIB July 18, 1994 appcCpicAdminParLuAlias, appcCpicAdminParLuName, appcCpicAdminModeName, appcCpicAdminTpNameType, appcCpicAdminTpName, appcCpicAdminRowStatus, appcCpicAdminUserid, appcCpicOperLocLuName, appcCpicOperSymbDestName, appcCpicOperParLuAlias, appcCpicOperParLuName, appcCpicOperModeName, appcCpicOperTpNameType, appcCpicOperTpName, appcCpicOperUserid } STATUS current DESCRIPTION "A collection of objects providing the instrumentation of APPC CPI-C side information." ::= { appcGroups 10 } -- end of conformance statement END Expires December 1994 [Page 120] Internet Draft APPC MIB July 18, 1994 5. Acknowledgments This MIB module is the product of the SNA NAU MIB Working Group. 6. References [1] IBM, Systems Network Architecture Technical Overview, GC30-3073-3, March, 1991. [2] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1442, SNMP Research, Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993. [3] McCloghrie, K., and M. Rose, "Management Information Base for Network Management of TCP/IP-based internets - MIB-II", STD 17, RFC 1213, Hughes LAN Systems, Performance Systems International, March 1991. [4] Galvin, J., and K. McCloghrie, "Administrative Model for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1445, Trusted Information Systems, Hughes LAN Systems, April 1993. [5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1448, SNMP Research, Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993. [6] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1443, SNMP Research, Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993. [7] Kielczewski, Z., Kostick, D., and K. Shih, "Definitions of Managed Objects for SNA NAUs", RFC xxxx, Eicon Technology Corporation, Bellcore, Novell, Inc., May 1994. Expires December 1994 [Page 121] Internet Draft APPC MIB July 18, 1994 7. Security Considerations Security issues are not discussed in this memo. 8. Authors' Addresses Michael Allen Networking Systems IBM Corporation Research Triangle Park, NC 27709 Tel: 1 919 254 4442 E-mail: moallen@vnet.ibm.com Zbigniew Kielczewski Eicon Technology Corporation 2196 32nd Avenue Montreal, Quebec, Canada H8T 3H7 Tel: 1 514 631 2592 E-mail: zbig@eicon.qc.ca William Kwan CrossComm Corporation 450 Donald Lynch Blvd. Marlboro, MA 01752 Tel: 1 508 229 5429 E-mail: kwan@crosscomm.com Expires December 1994 [Page 122] Internet Draft APPC MIB July 18, 1994 9. Table of Contents 1 Introduction .................................................... 2 2 The SNMPv2 Network Management Framework ......................... 3 2.1 Object Definitions ............................................ 3 3 Overview ........................................................ 4 3.1 Applying MIB II to managing APPC devices ...................... 5 3.2 APPC MIB Structure ............................................ 5 3.2.1 appcGlobal group ............................................ 6 3.2.2 appcLu group ................................................ 7 3.2.3 appcTp group ................................................ 10 3.2.4 appcSession group ........................................... 11 3.2.5 appcConversation group ...................................... 11 3.2.6 appcCPIC group .............................................. 12 3.2.7 Conformance statement ....................................... 13 3.3 APPC MIB special feature ...................................... 13 3.3.1 Row Creation mechanism ...................................... 13 4 Object Definitions .............................................. 14 5 Acknowledgments ................................................. 121 6 References ...................................................... 121 7 Security Considerations ......................................... 122 8 Authors' Addresses .............................................. 122 9 Table of Contents ............................................... 123 Expires December 1994 [Page 123]