Network Working Group H. Schulzrinne Internet-Draft Columbia U. Expires: January 14, 2006 J. Polk Cisco July 13, 2005 Communications Resource Priority for the Session Initiation Protocol (SIP) draft-ietf-sip-resource-priority-10 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on January 14, 2006. Copyright Notice Copyright (C) The Internet Society (2005). Abstract This document defines two new SIP header fields for communicating resource priority, namely "Resource-Priority" and "Accept-Resource- Priority". The "Resource-Priority" header field can influence the behavior of SIP user agents, such as telephone gateways and IP telephones, and SIP proxies. It does not directly influence the forwarding behavior of IP routers. Schulzrinne & Polk Expires January 14, 2006 [Page 1] Internet-Draft SIP Resource Priority July 2005 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 7 3. The Resource-Priority and Accept-Resource-Priority SIP Header Fields . . . . . . . . . . . . . . . . . . . . . . . . 7 3.1 The 'Resource-Priority' Header Field . . . . . . . . . . . 7 3.2 The 'Accept-Resource-Priority' Header Field . . . . . . . 9 3.3 Usage of the 'Resource-Priority' and 'Accept-Resource-Priority' Header Fields . . . . . . . . . 9 3.4 The 'resource-priority' Option Tag . . . . . . . . . . . . 10 4. Behavior of SIP Elements that Receive Prioritized Requests . . 10 4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 10 4.2 General Rules . . . . . . . . . . . . . . . . . . . . . . 10 4.3 Usage of Require Header with Resource-Priority . . . . . . 11 4.4 OPTIONS Request with Resource-Priority . . . . . . . . . . 11 4.5 Approaches for Preferential Treatment of Requests . . . . 11 4.5.1 Preemption . . . . . . . . . . . . . . . . . . . . . . 12 4.5.2 Priority Queueing . . . . . . . . . . . . . . . . . . 12 4.6 Error Conditions . . . . . . . . . . . . . . . . . . . . . 13 4.6.1 Introduction . . . . . . . . . . . . . . . . . . . . . 13 4.6.2 No Known Namespace or Priority Value . . . . . . . . . 13 4.6.3 Authentication Failure . . . . . . . . . . . . . . . . 14 4.6.4 Authorization Failure . . . . . . . . . . . . . . . . 14 4.6.5 Insufficient Resources . . . . . . . . . . . . . . . . 14 4.6.6 Busy . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.7 Element-Specific Behaviors . . . . . . . . . . . . . . . . 15 4.7.1 User Agent Client Behavior . . . . . . . . . . . . . . 15 4.7.2 User Agent Server Behavior . . . . . . . . . . . . . . 16 4.7.3 Proxy Behavior . . . . . . . . . . . . . . . . . . . . 16 5. Third-Party Authentication . . . . . . . . . . . . . . . . . . 17 6. Backwards Compatibility . . . . . . . . . . . . . . . . . . . 18 7. Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1 Simple Call . . . . . . . . . . . . . . . . . . . . . . . 18 7.2 Receiver Does Not Understand Namespace . . . . . . . . . . 19 8. Handling Multiple Concurrent Namespaces . . . . . . . . . . . 21 8.1 General Rules . . . . . . . . . . . . . . . . . . . . . . 21 8.2 Examples of Valid Orderings . . . . . . . . . . . . . . . 22 8.3 Examples of Invalid Orderings . . . . . . . . . . . . . . 22 9. Registering Namespaces . . . . . . . . . . . . . . . . . . . . 23 10. Namespace Definitions . . . . . . . . . . . . . . . . . . . 24 10.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 24 10.2 The "DSN" Namespace . . . . . . . . . . . . . . . . . . . 24 10.3 The "DRSN" Namespace . . . . . . . . . . . . . . . . . . . 25 10.4 The "Q735" Namespace . . . . . . . . . . . . . . . . . . . 25 10.5 The "ETS" Namespace . . . . . . . . . . . . . . . . . . . 26 10.6 The "WPS" Namespace . . . . . . . . . . . . . . . . . . . 26 11. Security Considerations . . . . . . . . . . . . . . . . . . 27 Schulzrinne & Polk Expires January 14, 2006 [Page 2] Internet-Draft SIP Resource Priority July 2005 11.1 General Remarks . . . . . . . . . . . . . . . . . . . . . 27 11.2 Authentication and Authorization . . . . . . . . . . . . . 27 11.3 Confidentiality and Integrity . . . . . . . . . . . . . . 28 11.4 Anonymity . . . . . . . . . . . . . . . . . . . . . . . . 29 11.5 Denial-of-Service Attacks . . . . . . . . . . . . . . . . 29 12. IANA Considerations . . . . . . . . . . . . . . . . . . . . 29 12.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . 29 12.2 IANA Registration of 'Resource-Priority' and 'Accept-Resource-Priority' Header Fields . . . . . . . . . 30 12.3 IANA Registration for Option Tag resource-priority . . . . 30 12.4 IANA Registration for Response Code 417 . . . . . . . . . 30 12.5 IANA Resource-Priority Namespace Registration . . . . . . 31 12.6 IANA Priority-Value Registrations . . . . . . . . . . . . 31 13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . 32 14. References . . . . . . . . . . . . . . . . . . . . . . . . . 32 14.1 Normative References . . . . . . . . . . . . . . . . . . . 32 14.2 Informative References . . . . . . . . . . . . . . . . . . 33 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . 35 Intellectual Property and Copyright Statements . . . . . . . . 36 Schulzrinne & Polk Expires January 14, 2006 [Page 3] Internet-Draft SIP Resource Priority July 2005 1. Introduction During emergencies, communications resources including telephone circuits, IP bandwidth and gateways between the circuit-switched and IP networks may become congested. Congestion can occur due to heavy usage, loss of resources caused by the natural or man-made disaster and attacks on the network during man-made emergencies. This congestion may make it difficult for persons charged with emergency assistance, recovery or law enforcement to coordinate their efforts. As IP networks become part of converged or hybrid networks along with public and private circuit-switched (telephone) networks, it becomes necessary to ensure that these networks can assist during such emergencies. Also, users may want to interrupt their lower-priority communications activities and dedicate their end system resources to the high- priority communications attempt if a high-priority communications request arrives at their end system. There are many IP-based services that can assist during emergencies. This memo only covers real-time communications applications involving the Session Initiation Protocol (SIP) [RFC3261], including voice- over-IP, multimedia conferencing, instant messaging and presence. SIP applications may involve at least five different resources that may become scarce and congested during emergencies. These resources include gateway resources, circuit-switched network resources, IP network resources, receiving end system resources and SIP proxy resources. IP network resources are beyond the scope of SIP signaling and are therefore not considered here. Even if the resources at the SIP element itself are not scarce, a SIP gateway may mark outgoing calls with an indication of priority, e.g., in an ISUP IAM message originated by the gateway. In order to improve emergency response, it may become necessary to prioritize access to SIP-signaled resources during periods of emergency-induced resource scarcity. We call this "resource prioritization". The mechanism itself may well be in place at all times, but only materially affect call handling during times of resource scarcity. Currently, SIP does not include a mechanism that allows a request originator to indicate to a SIP element that it wishes the request to invoke such resource prioritization. To address this need, this document adds a SIP protocol element that labels certain SIP requests. Schulzrinne & Polk Expires January 14, 2006 [Page 4] Internet-Draft SIP Resource Priority July 2005 This document defines (Section 3) two new SIP header field for communications resource priority, called 'Resource-Priority' and 'Accept-Resource-Priority'. The 'Resource-Priority' header field MAY be used by SIP user agents, including General Switched Telephone Network (GSTN) gateways and terminals, and SIP proxy servers to influence their treatment of SIP requests, including the priority afforded to GSTN calls. For GSTN gateways, the behavior translates into analogous schemes in the GSTN, for example the ITU Recommendation Q.735.3 [Q.735.3] prioritization mechanism, in both the GSTN-to-IP and IP-to-GSTN directions. ITU Recommendation I.255.3 [I.255.3] is another example. A SIP request with a 'Resource-Priority' indication can be treated differently in these situations: 1. The request can be given elevated priority for access to GSTN gateway resources such as trunk circuits. 2. The request can interrupt lower-priority requests at a user terminal, such as an IP phone. 3. The request can carry information from one multi-level priority domain in the telephone network, e.g., using the facilities of Q.735.3 [Q.735.3], to another, without the SIP proxies themselves inspecting or modifying the header field. 4. In SIP proxies and back-to-back user agents, requests of higher priorities may displace existing signaling requests or bypass GSTN gateway capacity limits in effect for lower priorities. This header field is related to, but differs in semantics from, the 'Priority' header field ([RFC3261], Section 20.26). The 'Priority' header field describes the importance that the SIP request should have to the receiving human or its agent. For example, that header may be factored into decisions about call routing to mobile devices and assistants and call acceptance when the call destination is busy. The 'Priority' header field does not affect the usage of GSTN gateway or proxy resources, for example. In addition, any User Agent Client (UAC) can assert any 'Priority' value, while usage of 'Resource- Priority' header field values is subject to authorization. While the 'Resource-Priority' header field does not directly influence the forwarding behavior of IP routers or the use of communications resources such as packet forwarding priority, procedures for using this header field to cause such influence may be defined in other documents. Existing implementations of RFC 3261 that do not participate in the resource priority mechanism follow the normal rules of RFC 3261, Section 8.2.2: "If a UAS does not understand a header field in a request (that is, the header field is not defined in this Schulzrinne & Polk Expires January 14, 2006 [Page 5] Internet-Draft SIP Resource Priority July 2005 specification or in any supported extension), the server MUST ignore that header field and continue processing the message." Thus, the use of this mechanism is wholly invisible to existing implementations unless the request includes the Require header field with the resource-priority option tag. The mechanism described here can be used for emergency preparedness in emergency telecommunications systems, but is only a small part of an emergency preparedness network and is not restricted to such use. The mechanism aims to satisfy the requirements in [RFC3487]. It is structured so that it works in all SIP and Real-Time Transport Protocol (RTP) [RFC3550] transparent networks defined in [RFC3487]. In such networks, all network elements and SIP proxies let valid SIP requests pass through unchanged. This is important since it is likely that this mechanism will often be deployed in networks where the edge networks are unaware of the resource priority mechanism and provide no special privileges to such requests. The request then reaches a GSTN gateway or set of SIP elements that are aware of the mechanism. For conciseness, we refer to SIP proxies and user agents (UAs) that act on the 'Resource-Priority' header field as RP actors. It is likely to be common that the same SIP element will handle requests that bear the 'Resource-Priority' header fields and those that do not. Government entities and standardization bodies have developed several different priority schemes for their networks. Users would like to be able to obtain authorized priority handling in several of these networks, without changing SIP clients. Also, a single call may traverse SIP elements that are run by different administrations and subject to different priority mechanisms. Since there is no global ordering among those priorities, we allow each request to contain more than one priority value drawn from these different priority lists, called a namespace in this document. Typically, each SIP element only supports one such namespace, but we discuss what happens if an element needs to support multiple namespaces in Section 8. Since gaining prioritized access to resources offers opportunities to deny service to others, it is expected that all such prioritized calls are subject to authentication and authorization, using standard SIP security mechanisms (Section 11). The remainder of this document is structured as follows. After defining terminology in Section 2, we define the syntax for the two new SIP header fields in Section 3 and then describe protocol Schulzrinne & Polk Expires January 14, 2006 [Page 6] Internet-Draft SIP Resource Priority July 2005 behavior in Section 4. The two principal mechanisms for differentiated treatment of SIP requests, namely preemption and queuing, are described in Section 4.5. Error conditions are covered in Section 4.6. Section 4.7.1 through Section 4.7.3 detail the behavior of specific SIP elements. Third-party authentication is briefly summarized in Section 5. Section 6 describes how this feature affects existing systems that do not support it. Since calls may traverse multiple administrative domains with different namespaces or multiple elements with the same namespace, it is strongly suggested that all such domains and elements apply the same algorithms for the same namespace as otherwise the end-to-end experience of privileged users may be compromised. Section 9 enumerates the information that namespace registrations need to provide. Section 8 discusses what happens if a request contains multiple namespaces or an element can handle more than one namespace. Section 10 defines the properties of five namespaces that are registered through this document. Protocol examples are given in Section 7. Security issues are considered in Section 11, but this document does not define new security mechanisms. Section 12 discusses IANA considerations and registers parameters related to this document. 2. Terminology In this document, the key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" are to be interpreted as described in BCP 14, RFC 2119 [RFC2119] and indicate requirement levels for compliant implementations. 3. The Resource-Priority and Accept-Resource-Priority SIP Header Fields This section defines the 'Resource-Priority' and 'Accept-Resource- Priority' SIP header field syntax. Behavior is described in Section 4. 3.1 The 'Resource-Priority' Header Field The 'Resource-Priority' request header field marks a SIP request as desiring prioritized access to resources, as described in the introduction. There is no protocol requirement that all requests within a SIP dialog or session use the 'Resource-Priority' header field. Local administrative policy MAY mandate the inclusion of the 'Resource- Priority' header field in all requests. Implementations of this Schulzrinne & Polk Expires January 14, 2006 [Page 7] Internet-Draft SIP Resource Priority July 2005 specification MUST allow inclusion to be either by explicit user request or automatically for all requests. The syntax of the 'Resource-Priority' header field is described below. The "token-nodot" production is copied from [RFC3265]. Resource-Priority = "Resource-Priority" HCOLON r-value *(COMMA r-value) r-value = namespace "." r-priority namespace = token-nodot r-priority = token-nodot token-nodot = 1*( alphanum / "-" / "!" / "%" / "*" / "_" / "+" / "`" / "'" / "~" ) An example 'Resource-Priority' header field is shown below: Resource-Priority: dsn.flash The 'r-value' parameter in the 'Resource-Priority' header field indicates the resource priority desired by the request originator. Each resource value (r-value) is formatted as 'namespace' '.' 'priority value'. The value is drawn from the namespace identified by the 'namespace' token. Namespaces and priorities are case- insensitive ASCII tokens that do not contain periods. Thus, "dsn.flash" and "DSN.Flash", for example, are equivalent. Each namespace has at least one priority value. Namespaces and priority values within each namespace MUST be registered with IANA (Section 12). Initial namespace registrations are described in Section 12.5. Since a request may traverse multiple administrative domains with multiple different namespaces, it is necessary to be able to enumerate several different namespaces within the same message. However, a particular namespace MUST NOT appear more than once in the same SIP message. These may be expressed equivalently as either comma-separated lists within a single header field, as multiple header fields or some combination. The ordering of 'r-values' within the header field has no significance. Thus, for example, the following three header snippets are equivalent: Resource-Priority: dsn.flash, wps.3 Resource-Priority: wps.3, dsn.flash Resource-Priority: wps.3 Resource-Priority: dsn.flash Schulzrinne & Polk Expires January 14, 2006 [Page 8] Internet-Draft SIP Resource Priority July 2005 3.2 The 'Accept-Resource-Priority' Header Field The 'Accept-Resource-Priority' response header field enumerates the resource values (r-values) a SIP user agent server is willing to process. (This does not imply that a call with such values will find sufficient resources and succeed.) The syntax of the 'Accept- Resource-Priority' header field is as follows: Accept-Resource-Priority = "Accept-Resource-Priority" HCOLON [r-value *(COMMA r-value)] An example is given below: Accept-Resource-Priority: dsn.flash-override, dsn.flash, dsn.immediate, dsn.priority, dsn.routine Some administrative domains MAY choose to disable the use of the 'Accept-Resource-Priority' header as revealing too much information about that domain in responses. However, this behavior is NOT RECOMMENDED, as this header field aids in troubleshooting. 3.3 Usage of the 'Resource-Priority' and 'Accept-Resource-Priority' Header Fields The following table extends the values in Table 2 of RFC3261 [RFC3261]. (The PRACK method, labeled as PRA, is defined in [RFC3262], the SUBSCRIBE (labeled SUB) and NOTIFY (labeled NOT) methods in [RFC3265], the UPDATE (UPD) method in [RFC3311], the MESSAGE (MSG) method in [RFC3428], the REFER (REF) method in [RFC3515], the INFO (INF) method in [RFC2976], and the PUBLISH (PUB) method is in [RFC3903].) Header field where proxy INV ACK CAN BYE REG OPT PRA ---------------------------------------------------------------- Resource-Priority R amdr o o o o o o o Accept-Resource-Priority 200 amdr o - o o o o o Accept-Resource-Priority 417 amdr o - o o o o o Header field where proxy SUB NOT UPD MSG REF INF PUB ---------------------------------------------------------------- Resource-Priority R amdr o o o o o o o Accept-Resource-Priority 200 amdr o o o o o o o Accept-Resource-Priority 417 amdr o o o o o o o Other request methods MAY define their own handling rules; unless otherwise specified, recipients MAY ignore these header fields. Schulzrinne & Polk Expires January 14, 2006 [Page 9] Internet-Draft SIP Resource Priority July 2005 3.4 The 'resource-priority' Option Tag This document also defines the "resource-priority" option tag. The behavior is described in Section 4.3. and the IANA registration is in Section 12.3. 4. Behavior of SIP Elements that Receive Prioritized Requests 4.1 Introduction All SIP user agents and proxy servers that support this specification share certain common behavior, which we describe below in Section 4.2. The behavior when encountering a 'resource-priority' option tag in a 'Require' header field is describe in Section 4.3. Section 4.4 describes the treatment of OPTIONS requests. The two fundamental resource contention resolution mechanisms, preemption and queueing, are described in Section 4.5. Section 4.6 explains what happens when requests fail. Behavior specific to user agent clients, servers and proxy servers are covered in Section 4.7. 4.2 General Rules The 'Resource-Priority' header field is potentially applicable to all SIP request messages. At a minimum, implementations of the following request types MUST support the Resource-Priority header to be in compliance with this specification: o INVITE [RFC3261] o ACK [RFC3261] o PRACK [RFC3262] o UPDATE [RFC3311] o REFER [RFC3515] Implementations SHOULD support the 'Resource-Priority' header field in the following request types: o MESSAGE [RFC3428] o SUBSCRIBE [RFC3265] o NOTIFY [RFC3265] Note that this does not imply that all implementations have to support all requests methods listed. If a SIP element receives the 'Resource-Priority' header field in a request other than those listed above, the header MAY be ignored, according to the rules of [RFC3261]. In short, an RP actor performs the following steps when receiving a Schulzrinne & Polk Expires January 14, 2006 [Page 10] Internet-Draft SIP Resource Priority July 2005 prioritized request. Error behavior is described in Section 4.6. 1. If the RP actor recognizes none of the name spaces, treat the request as if it had no 'Resource-Priority' header field. 2. Ascertain that the request is authorized according to local policy to use the priority levels indicated. If the request is not authorized, reject it. Examples of authorization policies are discussed in Security Considerations (Section 11). 3. If the request is authorized and resources are available (no congestion), serve the request as usual. If the request is authorized, but resources are not available (congestion), either preempt other current sessions or insert the request into a priority queue, as described in Section 4.5. 4.3 Usage of Require Header with Resource-Priority Following standard SIP behavior, if a SIP request contains the 'Require' header field with the 'resource-priority' option tag, a SIP user agent MUST respond with a 420 (Bad Extension) if it does not support the SIP extensions described in this document. It then lists "resource-priority" in the 'Unsupported' header field included in the response. The use of the 'resource-priority' option tag in 'Proxy-Require' header field is NOT RECOMMENDED. 4.4 OPTIONS Request with Resource-Priority An OPTIONS request can be used to determine if an element supports the mechanism. A compliant implementation MUST return a 'Accept- Resource-Priority' header field in OPTIONS responses enumerating all valid resource values. An RP actor MAY be configured not to return such values or only return them to authorized requestors. Following standard SIP behavior, OPTIONS responses MUST include the 'Supported' header field that includes the 'resource-priority' option tag. According to RFC 3261, Section 11, proxies that receive a request with a 'Max-Forwards' header field value of zero MAY answer the OPTIONS request, allowing a UAC to discover the capabilities of both proxy and user agent servers. 4.5 Approaches for Preferential Treatment of Requests SIP elements may use the resource priority mechanism to modify a variety of behavior such as routing requests, authentication requirements, override of network capacity controls or logging. The Schulzrinne & Polk Expires January 14, 2006 [Page 11] Internet-Draft SIP Resource Priority July 2005 resource priority mechanism may influence the treatment of the request itself, the marking of outbound PSTN calls at a gateway or of the session created by the request. (Here, we use the terms session and call interchangeably in this document, both implying a continuous data stream between two or more parties. Sessions are established by SIP dialogs.) Below, we define two common algorithms, namely preemption and priority queueing. Preemption applies only to sessions created by SIP requests, while both sessions and request handling can be subject to priority queueing. Both algorithms can sometimes be combined in the same element, although none of the namespaces described in this document do this. Algorithms can be defined for each namespace or, in some cases, can be specific to an administrative domain. Other behavior, such as request routing or network management controls, is not defined by this specification. Naturally, only SIP elements that understand this mechanism and the namespace and resource value perform these algorithms. Section 4.6.2 discusses what happens if an RP actor does not understand priority values contained in a request. 4.5.1 Preemption An RP actor following a preemption policy may disrupt an existing session to make room for a higher-priority incoming session. Since sessions may require different amounts of bandwidth or number of circuits, a single higher priority session may displace more than one lower-priority session. Unless otherwise noted, requests do not preempt other requests of equal priority. As noted above, the processing of SIP requests itself is not preempted. Thus, since proxies do not manage sessions, they do not perform preemption. [I-D.ietf-sipping-reason-header-for-preemption] contains more details and examples of this behavior. UAS behavior for preemption is discussed in Section 4.7.2. 4.5.2 Priority Queueing In a priority queueing policy, requests that find no available resources are queued to the queue assigned to the priority value. Unless otherwise specified, requests are queued in first-come, first- served order. Each priority value may have its own queue or several priority values may share a single queue. If a resource becomes available, the RP actor selects the request from the highest-priority non-empty queue according to the queue service policy. For first- come, first-served policies, the request from that queue that has Schulzrinne & Polk Expires January 14, 2006 [Page 12] Internet-Draft SIP Resource Priority July 2005 been waiting the longest is served. Each queue can hold a finite number of pending requests. If the per-priority-value queue for a newly arriving request is full, the request is rejected immediately. In addition, a priority queueing policy MAY impose a waiting time limit for each priority class, where requests that exceed a specified waiting time are ejected from the queue and a failure response is returned to the requestor. Finally, an RP actor MAY impose a global queue size limit summed across all queues and drop waiting lower-priority requests. This does not imply preemption since the session has not been established yet. 4.6 Error Conditions 4.6.1 Introduction In this section, we describe the error behavior that is shared among multiple types of RP actors, including various instances of UAS such as trunk gateways, line gateways and IP phones, and proxies. A request containing a resource priority indication can fail for four reasons: the RP actor does not understand the priority value (Section 4.6.2), the requestor is not authenticated (Section 4.6.3), an authenticated requestor is not authorized to make such a request (Section 4.6.4) or there are insufficient resources for an authorized request (Section 4.6.5). We treat these error cases in the order that they typically arise in the processing of requests with Resource-Priority headers. However, this order is not mandated. For example, an RP actor that knows that a particular resource value cannot be served or queued MAY, as a matter of local policy, forego authorization since it would only add processing load without changing the outcome. 4.6.2 No Known Namespace or Priority Value If an RP actor does not understand any of the resource values in the request, the treatment depends on the presence of the 'Require' 'resource-priority' option tag: 1. Without the option tag, the RP actor treats the request as if it contained no 'Resource-Priority' header field and processes it with default priority. Resource values that are not understood MUST NOT be modified or deleted. 2. With the option tag, it MUST reject the request with a 417 (Unknown Resource-Priority) response code. Making case (1) the default is necessary since otherwise there would Schulzrinne & Polk Expires January 14, 2006 [Page 13] Internet-Draft SIP Resource Priority July 2005 be no way to successfully complete any calls in the case where a proxy on the way to the UAS shares no common namespaces with the UAC, but the UAC and UAS do have such a namespace in common. In general, as noted, a SIP request can contain more than one 'Resource-Priority' header field. This is necessary if a request needs to traverse different administrative domains, each with their own set of valid resource values. For example, the ETS namespace might be enabled for United States government networks that also support the DSN and/or DRSN namespaces for most individuals in those domains. A 417 (Unknown Resource-Priority) response MAY, according to local policy, include an 'Accept-Resource-Priority' header field enumerating the acceptable resource values. 4.6.3 Authentication Failure If the request is not authenticated, a 401 (Unauthorized) or 407 (Proxy Authentication Required) response is returned to allow the requestor to insert appropriate credentials. 4.6.4 Authorization Failure If the RP actor receives an authenticated request with a namespace and priority value it recognizes, but the originator is not authorized for that level of service, the element MUST return a 403 (Forbidden) response. 4.6.5 Insufficient Resources Insufficient resource conditions can occur on proxy servers and user agent servers, typically trunk gateways, if an RP actor receives an authorized request, has insufficient resources and the request neither preempts another session nor is queued. A request can fail either because the RP actor has insufficient processing capacity to handle the SIP request or insufficient bandwidth or trunk capacity to establish the requested session for session-creating SIP requests. If the request fails since the RP actor cannot handle the signaling load, the RP actor responds with 503 (Service Unavailable). If there is not enough bandwidth or an insufficient number of trunks, a 488 (Not Acceptable Here) response indicates that the RP actor is rejecting the request for reasons of media path availability, such as insufficient gateway resources. In that case, [RFC3261] advises that a 488 response SHOULD include a 'Warning' header field with a reason for the rejection, with warning code 370 (Insufficient Bandwidth) Schulzrinne & Polk Expires January 14, 2006 [Page 14] Internet-Draft SIP Resource Priority July 2005 typical. For systems implementing queueing, if the request is queued, the UAS will return 408 (Request Timeout) if the request exceeds the maximum configured waiting time in queue. 4.6.6 Busy Resource contention also occurs when a call request arrives at a UAS that is unable to accept another call, either because the UAS has just one line presence or has active calls on all line presences. If the call request indicates an equal or lower priority value compared to all active calls present on the UAS, the UAS returns a 486 (Busy here) response. If the request is queued instead, the UAS will return 408 (Request Timeout) if the request exceeds the maximum configured waiting time in the device queue. If a proxy gets 486 (Busy Here) responses on all branches, it can then return a 600 (Busy Everywhere) response to the caller. 4.7 Element-Specific Behaviors 4.7.1 User Agent Client Behavior SIP UACs supporting this specification MUST be able to generate the 'Resource-Priority' header field for requests that require elevated resource access priority. As stated previously, the UAC SHOULD be able to generate more than one resource value in a single SIP request. Upon receiving a 417 (Unknown Resource-Priority) response, the UAC MAY attempt a subsequent request with the same or different resource value. If available, it SHOULD choose authorized resource values from the set of values returned in the 'Accept-Resource-Priority' header field. 4.7.1.1 User Agent Client Behavior with a Preemption Algorithm A UAC that requests a priority value that may cause preemption MUST understand a Reason header field in the BYE request explaining why the session was terminated, as discussed in [I-D.ietf-sipping-reason- header-for-preemption]. 4.7.1.2 User Agent Client Behavior with a Queueing Policy By standard SIP protocol rules, a UAC MUST be prepared to receive a Schulzrinne & Polk Expires January 14, 2006 [Page 15] Internet-Draft SIP Resource Priority July 2005 182 (Queued) response from an RP actor that is currently at capacity, but has put the original request into a queue. A UAC MAY indicate this queued status to the user by some audio or visual indication to prevent the user from interpreting the call as having failed. 4.7.2 User Agent Server Behavior The precise effect of the 'Resource-Priority' indication depends on the type of UAS, the namespace and local policy. 4.7.2.1 User Agent Servers and Preemption Algorithm A UAS compliant with this specification MUST terminate a session established with a valid namespace and lower priority value in favor of a new session set-up with a valid namespace and higher relative priority-value, unless local policy has some form of call-waiting capability enabled. If a session is terminated, the BYE method is used with a 'Reason' header field indicating why and where the preemption took place. Implementors have a number of choices in how to implement preemption at IP phones with multiple line presences, i.e., with devices that can handle multiple simultaneous sessions. Naturally, if that device has exhausted the number of simultaneous sessions, one of the sessions needs to be replaced. If the device has spare sessions, an implementation MAY choose to alert the callee to the arrival of a higher-priority call. Details may also be set by local or namespace policy. [I-D.ietf-sipping-reason-header-for-preemption] provides additional information in the case of purposeful or administrative termination of a session by including the Reason header in the BYE message that states why the BYE was sent (in this case, a preemption event). The mechanisms in that document allow to indicate where the termination occurred ('at the UA', 'in the network', 'at a IP/PSTN gateway'), and includes call flow examples of each reason. 4.7.2.2 User Agent Servers and Queue-based Policy A UAS compliant with this specification SHOULD generate a 182 (Queued) response if that element's resources are busy, until it is able to handle the request and provide a final response. The frequency of such provisional messages is governed by [RFC3261]. 4.7.3 Proxy Behavior SIP proxies MAY ignore the 'Resource-Priority' header field. SIP proxies MAY reject any unauthenticated request bearing that header Schulzrinne & Polk Expires January 14, 2006 [Page 16] Internet-Draft SIP Resource Priority July 2005 field. When the 'Require' header field is included in a message, it ensures that in parallel forking, only branches that support the resource- priority mechanism succeed. If S/MIME encapsulation is used according to Section 23 of RFC 3261, special considerations apply. As tabulated in Section 3.3, the 'Resource-Priority' header field can be modified by proxies and thus is exempted by the integrity checking described in Section 23.4.1.1 of RFC 3261. Since it may need to be inspected or modified by proxies, the header field MUST also be placed in the "outer" message if the UAC would like proxy servers to be able to act on the header information. Similar considerations apply if parts of the message are integrity-protected or encrypted as described in [RFC3420]. If S/MIME is not used or if the 'Resource-Priority' header field is in the "outer" header, SIP proxies MAY downgrade or upgrade the 'Resource-Priority' of a request or insert a new 'Resource-Priority' header if allowed by local policy. If a stateful proxy has authorized a particular resource priority level and if it offers differentiated treatment to responses containing resource priority levels, the proxy SHOULD ignore any higher value contained in responses, to prevent colluding user agents from artificially raising the priority level. A SIP proxy MAY use the 'Resource-Priority' indication in its routing decisions, e.g., to retarget to a SIP node or SIP URI that is reserved for a particular resource priority. There are no special considerations for proxies when forking requests containing a resource priority indication. Otherwise, the proxy behavior is the same as for user agent servers described in Section 4.7.2. 5. Third-Party Authentication In some cases, the RP actor may not be able to authenticate the requestor or determine whether an authenticated user is authorized to make such a request. In these circumstances, the SIP entity may avail itself of general SIP mechanisms that are not specific to this application. The authenticated identity management mechanism [RFC3893] allows a third party to verify the identity of the requestor and certify this towards an RP actor. In networks with mutual trust, the SIP asserted identity mechanism [RFC3325] can help the RP actor determine the identity of the requestor. Schulzrinne & Polk Expires January 14, 2006 [Page 17] Internet-Draft SIP Resource Priority July 2005 6. Backwards Compatibility The resource priority mechanism described in this document is fully backwards compatible with SIP systems following [RFC3261]. Systems that do not understand the mechanism can only deliver standard, not elevated, service priority. User agent servers and proxies can ignore any 'Resource-Priority' header field just like any other unknown header field and then treat the request like any other request. Naturally, the request may still succeed. 7. Examples The SDP message body and the BYE and ACK exchanges are the same as in RFC 3665 [RFC3665] and omitted for brevity. 7.1 Simple Call User A User B | | | INVITE F1 | |----------------------->| | 180 Ringing F2 | |<-----------------------| | | | 200 OK F3 | |<-----------------------| | ACK F4 | |----------------------->| | Both Way RTP Media | |<======================>| | | In this scenario, User A completes a call to User B directly. The call from A to B is marked with a resource priority indication. Schulzrinne & Polk Expires January 14, 2006 [Page 18] Internet-Draft SIP Resource Priority July 2005 F1 INVITE User A -> User B INVITE sip:UserB@biloxi.example.com SIP/2.0 Via: SIP/2.0/TCP client.atlanta.example.com:5060;branch=z9hG4bK74bf9 Max-Forwards: 70 From: BigGuy ;tag=9fxced76sl To: LittleGuy Call-ID: 3848276298220188511@atlanta.example.com CSeq: 1 INVITE Resource-Priority: dsn.flash Contact: Content-Type: application/sdp Content-Length: ... ... F2 180 Ringing User B -> User A SIP/2.0 180 Ringing Via: SIP/2.0/TCP client.atlanta.example.com:5060;branch=z9hG4bK74bf9 ;received=192.0.2.101 From: BigGuy ;tag=9fxced76sl To: LittleGuy ;tag=8321234356 Call-ID: 3848276298220188511@atlanta.example.com CSeq: 1 INVITE Contact: Content-Length: 0 F3 200 OK User B -> User A SIP/2.0 200 OK Via: SIP/2.0/TCP client.atlanta.example.com:5060;branch=z9hG4bK74bf9 ;received=192.0.2.101 From: BigGuy ;tag=9fxced76sl To: LittleGuy ;tag=8321234356 Call-ID: 3848276298220188511@atlanta.example.com CSeq: 1 INVITE Contact: Content-Type: application/sdp Content-Length: ... ... 7.2 Receiver Does Not Understand Namespace In this example, the receiving UA does not understand the "dsn" Schulzrinne & Polk Expires January 14, 2006 [Page 19] Internet-Draft SIP Resource Priority July 2005 namespace and thus returns a 417 (Unknown Resource-Priority) status code. We omit the message details for messages F5 through F7 since they are essentially the same as in the first example. User A User B | | | INVITE F1 | |----------------------->| | 417 R-P failed F2 | |<-----------------------| | ACK F3 | |----------------------->| | | | INVITE F4 | |----------------------->| | 180 Ringing F5 | |<-----------------------| | 200 OK F6 | |<-----------------------| | ACK F7 | |----------------------->| | | | Both Way RTP Media | |<======================>| F1 INVITE User A -> User B INVITE sip:UserB@biloxi.example.com SIP/2.0 Via: SIP/2.0/TCP client.atlanta.example.com:5060;branch=z9hG4bK74bf9 Max-Forwards: 70 From: BigGuy ;tag=9fxced76sl To: LittleGuy Call-ID: 3848276298220188511@atlanta.example.com CSeq: 1 INVITE Require: resource-priority Resource-Priority: dsn.flash Contact: Content-Type: application/sdp Content-Length: ... ... F2 417 Resource-Priority failed User B -> User A SIP/2.0 417 Unknown Resource-Priority Via: SIP/2.0/TCP client.atlanta.example.com:5060;branch=z9hG4bK74bf9 Schulzrinne & Polk Expires January 14, 2006 [Page 20] Internet-Draft SIP Resource Priority July 2005 ;received=192.0.2.101 From: BigGuy ;tag=9fxced76sl To: LittleGuy ;tag=8321234356 Call-ID: 3848276298220188511@atlanta.example.com CSeq: 1 INVITE Accept-Resource-Priority: q735.0, q735.1, q735.2, q735.3, q735.4 Contact: Content-Type: application/sdp Content-Length: 0 F3 ACK User A -> User B ACK sip:UserB@biloxi.example.com SIP/2.0 Via: SIP/2.0/TCP client.atlanta.example.com:5060;branch=z9hG4bK74bd5 Max-Forwards: 70 From: BigGuy ;tag=9fxced76sl To: LittleGuy ;tag=8321234356 Call-ID: 3848276298220188511@atlanta.example.com CSeq: 1 ACK Content-Length: 0 F4 INVITE User A -> User B INVITE sip:UserB@biloxi.example.com SIP/2.0 Via: SIP/2.0/TCP client.atlanta.example.com:5060;branch=z9hG4bK74bf9 Max-Forwards: 70 From: BigGuy ;tag=9fxced76sl To: LittleGuy Call-ID: 3848276298220188511@atlanta.example.com CSeq: 2 INVITE Require: resource-priority Resource-Priority: q735.3 Contact: Content-Type: application/sdp Content-Length: ... ... 8. Handling Multiple Concurrent Namespaces 8.1 General Rules A single SIP request MAY contain resource values from multiple namespaces. As noted earlier, an RP actor disregards all namespaces it does not recognize. This specification only addresses the case where an RP actor then selects one of the remainining resource values for processing, usually choosing the one with the highest relative Schulzrinne & Polk Expires January 14, 2006 [Page 21] Internet-Draft SIP Resource Priority July 2005 priority. If an RP actor understands multiple namespaces, it MUST create a local total ordering across all resource values from these namespaces, maintaining the relative ordering within each namespace. It is RECOMMENDED that the same ordering is used across an administrative domain. However, there is no requirement that such ordering be the same across all administrative domains. 8.2 Examples of Valid Orderings Below are a set of examples of an RP actor that supports two namespaces, foo and bar. Foo's priority-values are 3 (highest), then 2 and then 1 (lowest), and bar's priority-values are C (highest), then B and then A (lowest). Below are five lists of acceptable priority orders the SIP element may use: Foo.3 Foo.3 Bar.C (highest priority) Foo.2 Bar.C Foo.3 Foo.1 or Foo.2 or Foo.2 Bar.C Bar.B Foo.1 Bar.B Foo.1 Bar.B Bar.A Bar.A Bar.A (lowest priority) Bar.C (highest priority) Foo.3 Bar.B (both treated with equal priority (FIFO)) or Foo.2 Bar.A (both treated with equal priority (FIFO)) Foo.1 (lowest priority) Bar.C (highest priority) Foo.3 or Foo.2 Foo.1 (lowest priority) In the last example above, Bar.A and Bar.B are ignored. 8.3 Examples of Invalid Orderings Based on the priority order of the namespaces above, the following combinations are examples of orderings that are NOT acceptable and MUST NOT be configurable: Schulzrinne & Polk Expires January 14, 2006 [Page 22] Internet-Draft SIP Resource Priority July 2005 Example 1 Example 2 Example 3 --------- --------- --------- Foo.3 Foo.3 Bar.C Foo.2 Bar.A Foo.1 Foo.1 or Foo.2 or Foo.3 Bar.C Bar.B Foo.2 Bar.A Foo.1 Bar.A Bar.B Bar.C Bar.B Example 4 --------- Bar.C Foo.1 Bar.B or Foo.3 Bar.A Foo.2 These examples are invalid since the following global orderings are not consistent with the namespace-internal order: o In Example 1, Bar.A is ordered higher than Bar.B; o In Example 2, Bar.A is ordered higher than Bar.B and Bar.C; o In Example 3, Foo.1 is ordered higher than Foo.2 and Foo.3; o In Example 4, Foo.1 is ordered higher than Foo.3 and Foo.2; 9. Registering Namespaces Organizations considering the use of the Resource-Priority header field should investigate if an existing combination of namespace and priority-values meets their needs. For example, emergency first responders around the world are discussing utilizing this mechanism for preferential treatment in future networks. There should not be a unique namespace for different jurisdictions. This will greatly increase interoperability and reduce development time, and probably reduce future confusion if there is ever a need to map one namespace to another in an interworking function. Below, we describe the steps necessary to register a new namespace. A new namespace MUST be defined in a Standards Track RFC, following the 'Standards Action' policy in [RFC2434] and MUST include the following facets: o It must define the namespace label, a unique namespace label within the IANA registry for the SIP Resource-Priority header field. o It must enumerate the priority levels, i.e., 'r-priority' values, the namespace is using. Note that only finite lists are permissible, not (e.g.,) unconstrained integers or tokens. Schulzrinne & Polk Expires January 14, 2006 [Page 23] Internet-Draft SIP Resource Priority July 2005 o The priority algorithm (Section 4.5), identifying whether the namespace is to be used with priority queueing ("queue") or preemption ("preemption"); if queueing is used, the namespace MAY indicate whether normal-priority requests are queued. If there is a new "intended algorithm" other than preemption or priority queueing, the algorithm must be described, taking into account all RP actors (UAC, UAS, proxies). o A namespace may either reference an existing list of priority values or define a new finite list of priority values in relative priority order for IANA registration within the sip-parameters Resource-Priority priority-values registry. New priority-values SHOULD NOT be added to a previously IANA-registered list associated with a particular namespace, as this may cause interoperability problems. Unless otherwise specified, it is assumed that all priority value confer higher priority than requests without a priority value. o Any new SIP response codes unique to this new namespace need to be explained and registered. o The reference document must specify and describe any new Warning header field warn-codes (RFC 3261, Section 27.2). o The document needs to specify a new row for the following table that summarize the features of the namespace and are included into IANA Resource-Priority Namespace registration: Intended New New resp. Namespace Levels algorithm warn-code code Reference --------- ------ ---------------- --------- -------- ---------