Network Working Group Ghyslain Pelletier, Ericsson AB INTERNET-DRAFT Expires: Avril 2004 October 27, 2003 RObust Header Compression (ROHC): Context Replication for ROHC Profiles Status of this memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or cite them other than as "work in progress". The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/lid-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html Abstract This document defines context replication, a complement to the context initialization procedure found in ROHC (Robust Header Compression) [RFC-3095]. Profiles defining support for context replication may use the mechanism described herein to establish a new context based on another already existing context. Context replication is introduced to reduce the overhead of the context establishment procedure, and may be especially useful for the compression of multiple short-lived flows that may be occurring simultaneously or near-simultaneously, such as for example short- lived TCP flows. Pelletier [Page 1] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 Table of contents 1. Introduction....................................................3 2. Terminology.....................................................4 3. Context replication for ROHC profiles...........................4 3.1. Robustness considerations.................................5 3.2. Operational assumptions...................................5 3.3. Compressor states and logic...............................5 3.3.1. Context Replication (CR) state..........................6 3.3.2. State machine with context replication..................6 3.3.3. State transition logic..................................7 3.3.3.1. Selection of the base context, upward transition......7 3.3.3.2. Optimistic approach, upward transition................8 3.3.3.3. Optional acknowledgements (ACKs), upward transition...8 3.3.3.4. Negative ACKs (NACKs), downward transition............8 3.4. Decompressor logic........................................9 3.4.1. Replication and context initialization..................9 3.4.2. Reconstruction and verification.........................9 3.4.3. Actions upon failure....................................9 3.5. Packet formats...........................................10 3.5.1. Checksums in the IR-CR packet..........................10 3.5.1.1. 7-bit CRC............................................11 3.5.1.2. 8-bit CRC............................................11 3.5.2. General format of the IR-CR packet.....................12 3.6. Inter-profile context replication........................13 3.6.1. Supporting inter-profile context replication...........13 3.6.2. Compatibility between profiles.........................14 4. Security considerations........................................14 5. Acknowledgements...............................................14 6. References.....................................................15 6.1. Normative references.....................................15 6.2. Informative references...................................15 7. Author's address...............................................15 Appendix A. General format of the IR-CR packet (informative)......16 A.1. General structure (informative)..........................16 A.2. Profile specific replication information(informative)....16 Full Copyright Statement...........................................17 Pelletier [Page 2] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 1. Introduction There is often some redundancy between header fields of different flows passing through the same compressor-decompressor pair. This means that some of the information needed to initialize the context for compressing the headers of a new flow may already be present at the decompressor. It may be desirable to reuse this information and remove some of the overhead normally required for the initialization of a new header compression context. Reducing the overhead of the context establishment procedure is particularly useful when multiple short-lived connections (or flows) occurs simultaneously, or near-simultaneously, between the same compressor-decompressor pair. Such flows may lead to lower header compression gains, as each new packet stream requires most of the header information to be sent initially and smaller compressed headers may only be sent thereafter. Context replication allows some header fields, such as the IP source and/or destination addresses (16 octets each for IPv6), to be omitted within the IR packet specially defined for replication. It also allows other fields, such as source and/or destination ports, to be either omitted or sent in a compressed form from the very first packet of the header compressed flow. In addition, this mechanism allows contexts from different profiles to be used with context replication, where for obvious reasons only header fields common to both profiles can possibly be replicated. Context replication is herein defined as a general ROHC mechanism; its support may be defined for any ROHC profile. However, although the benefits of context replication are not limited to any particular protocol, it is best motivated for TCP compression. Specifically, many TCP transfers are short-lived; a behavior analysis of TCP/IP header fields among multiple short-lived connections may be found in [TCP-BEH]. In addition, [TCP-REQ] introduces considerations and requirements for the ROHC-TCP profile [ROHC-TCP] to efficiently compress such short-lived TCP transfers. For profiles supporting this mechanism, context replication is performed by the compressor first initializing a new context for the new flow. This context is then populated using parts of an existing context, i.e. a base context, to create the replicated context. The compressor then sends to the decompressor a packet that contains a reference to the selected base context, along with some data for the fields that need to be updated when creating the replicated context. Finally, the decompressor creates the replicated context based on the reference to the base context along with the uncompressed and compressed data from the received packet. This document specifies the context replication procedure for ROHC profiles. It defines the general compressor and decompressor logic Pelletier [Page 3] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 used during context replication, as well as the general format of the special IR packet required for this procedure. Profiles defining support for context replication must further specify the specific format of this packet. The fundamentals of the ROHC framework may be found in [RFC-3095]. These are assumed to be understood throughout this document. 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC2119. This document reuses some of the terminology found in [RFC-3095]. In addition, this document defines the following terms: Base context A base context is a context that has been validated by both the compressor and the decompressor. A base context can be used by the compressor as the reference when building a new context using replication. Base CID The Base Context Identifier is the CID used to identify the base context, where information needed for context replication can be extracted from. Context replication Context replication is the mechanism that initializes a new context based on another already existing context (a base context). 3. Context Replication for ROHC profiles For profiles defining its support, context replication may be used as an alternative to the context initialization procedure found in [RFC- 3095]. Note that for such profiles, only the decompressor is mandated to support context replication; the use of the IR-CR packet is optional for the compressor. This section describes the compressor and decompressor logic as well as the general format of the IR packet used with context replication. Pelletier [Page 4] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 3.1. Robustness considerations Context replication deviates from the initialization procedure defined in [RFC-3095] by its capacity to achieve a certain level of compression already from the first packet used to initialize the context for a new flow. It is therefore of particular importance that the context replication procedure be robust. This requires that a base context suitable for replication be used, that the integrity of the initialization packet be guaranteed and finally that the outcome of the replication process be verified. The primary mechanisms used to achieve robustness of the context replication procedure are the selection of the base context based on prior feedback from the decompressor and the use of checksums. Specifically, the compressor must obtain enough confidence that the base context selected for replication is valid and available at the decompressor before initiating the replication procedure. The most reliable way to select the base context is thus to choose a context that has previously been acknowledged by the decompressor. In addition, the presence of a CRC covering the information that initializes the context ensures the integrity of the IR header used for replication. Finally, an additional CRC calculated over the original uncompressed header allows the decompressor to validate the reconstructed header and the outcome of the replication process. 3.2. Operational assumptions Modes of operation are profile specific [RFC-3095]. A profile supporting context replication and defining modes other than unidirectional (U-mode) or bi-directional optimistic (O-mode) modes of operation cannot replicate a context when: - a mode other than U- or O-mode is active at replication time or; - a mode transition is taking place unless proper logic to address the above cases is specified explicitly as part of that profile. 3.3. Compressor states and logic Compression with ROHC normally starts in the IR state, where IR packets must be sent to initialize a new context at the decompressor. IR packets include all static and non-static fields of the original header in uncompressed form plus some additional information. The compressor stays in the IR state until it obtains confidence that the information has been received by the decompressor. Context replication provides an optional mechanism to complement the ROHC initialization procedure. It defines a packet type, the IR Pelletier [Page 5] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 packet for Context Replication (IR-CR), that can be used to initialize a new context. Consequently, the Context Replication (CR) state is introduced to the compressor state machine to achieve compression from the very first packet being sent. For profiles defining support for context replication, the compressor may thus transit directly from the IR state to the CR state if an already existing context can be selected as a base context for replication. This effectively replace any IR/IR-DYN packets sent during the context establishment procedure with an IR-CR packet. 3.3.1. Context replication (CR) state The purpose of the CR state is to initialize a new context by reusing an already existing context. In this state, the compressor sends a combination of uncompressed and compressed information, along with a reference to a base context plus some additional information. Header information pertaining to fields that are being replicated is therefore not sent. The compressor stays in the CR state until it is fairly confident that the decompressor has received the replication information correctly. 3.3.2. State machine with context replication The compressor always start in the lower compression state (IR), and transit to the context replication state (CR) under the constraint that the compressor can select a base context that is suitable for the flow being compressed (see also section 3.3.3.1.). The transition from the CR state to a higher compression state (e.g. the CO state for [ROHC-TCP]) is based on the optimistic approach principle or feedback received from the decompressor. The figure below shows the additional state for the compressor. The details of the state transitions and compression logic are given in sub-sections following the figure. BCID selection Optimistic approach / ACK +----->----->------+ +----->----->----->-----+ | | | | | v | v +---------+ +---------+ +-------------+ | IR | | CR | | Higher | | state | | state | | order state | +---------+ +---------+ +-------------+ ^ | | NACK / STATIC-NACK | +---<-----<-----<----+ Pelletier [Page 6] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 Note that context replication is a complement to the normal initialization procedure for ROHC profiles supporting it. The compressor transition to the CR state is therefore an optional addition to the state machine, and this does not affect already existing transitions between the IR state and higher order state(s). 3.3.3. State transition logic Decisions about transition to and from the CR state are taken by the compressor on the basis of: - availability of a base context - positive feedback from the decompressor (Acknowledgements -- ACKs) - negative feedback from the decompressor (Negative ACKs -- NACKs) - confidence level regarding error-free decompression of a packet Context replication is designed to operate over links where a feedback channel is available. This is necessary to ensure that the information used to create a new context is synchronized between the compressor and the decompressor. In addition, context replication may also make use of feedback from decompressor to compressor for transition back to the IR state and for OPTIONAL improved forward transition towards a state with a higher compression ratio. [RFC-3095, section 5.2.2.] specifies the required format for the feedback field within the general ROHC packet format to be used by all profiles; the feedback information is structured using two possible formats: FEEDBACK-1 and FEEDBACK-2. In particular, FEEDBACK- 2 can carry one of three possible types of feedback information: ACK, NACK or STATIC-NACK. 3.3.3.1. Selection of base context, upward transition The compressor may initiate a transition from the IR state to the CR state when a suitable base context can be identified. To perform this transition, the compressor MUST select a context that has previously been acknowledged by the decompressor as the base context, and this base context must be valid at replication time. This also implies that a compressor is not allowed to use the context replication mechanism if a feedback channel is not present. Note however that this cannot provide the guarantee that the selected base context has not been corrupted after it has been acknowledged or that it is still part of the state managed by the decompressor when the IR-CR will be received. More specifically, [RFC-3095] defines the context identifier (CID) as a reference to the state information (i.e. the context) used for compression and decompression. Multiple packet streams - each having their own context - may thus share a channel, and the CID space along with its representation within packet formats may be negotiated as part of the channel state. However, because [RFC-3095] does not Pelletier [Page 7] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 explicitly define context state management between compressor and decompressor, and in particular for connection-oriented flows (e.g. TCP), only a high degree of confidence can be achieved when selecting a base context. In the case where feedback is not used by the decompressor, the compressor may have to periodically transit back to the IR state. In such case, the same logic applies for the transition back to the higher order state via the CR state: a base context previously acknowledged and suitable for replication must be re-selected. The criteria whether an existing context is a suitable base context for replication for a new flow are left to implementations. For simplicity, contexts with the same Source-IP and/or Destination-IP may be considered as replicable contexts, and the most recent one should be selected as the candidate to be replicated. Finally, the Base CID within the packet format of the IR-CR may be assigned a different value than the context identifier associated to the new flow (i.e. Base CID != CID); otherwise the base context is overwritten with the new context by the replication process. 3.3.3.2. Optimistic approach, upward transition Transition to a higher order state can be carried out according to the optimistic approach principle. This means that the compressor may perform an upward state transition when it is fairly confident that the decompressor has received enough information to correctly decompress packets sent according to the higher compression state. In general, there are many approaches where the compressor can obtain such information. The compressor may obtain its confidence by sending several IR-CR packets with the same information. 3.3.3.3. Optional acknowledgements (ACKs), upward transition An ACK may be sent by the decompressor to indicate that a context has been successfully initialized during context replication. Upon reception of an ACK, the compressor may assume that the context replication procedure was successful and transit from its initial state (e.g. IR state) to a higher compression state. 3.3.3.4. Negative ACKs (NACKs), downward transition A STATIC-NACK sent by the decompressor may indicate that a valid context could not be initialized by the decompressor during context replication, and the corresponding context has been invalidated. Upon reception of a STATIC-NACK, the compressor MUST transit back to its initial no context state and SHOULD refrain from sending IR-CR Pelletier [Page 8] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 packets using the same base context. The compressor SHOULD re- initialize the decompressor context using an IR packet. A NACK sent by the decompressor may indicate that a valid context has been successfully initialized but that the decompression of one or more subsequent packets has failed. Upon reception of a NACK, the compressor MAY assume that the static part of the decompressor context is valid but that the dynamic part is invalid, and take actions accordingly. 3.4. Decompressor logic 3.4.1. Replication and context initialization Upon reception of an IR-CR packet, the decompressor first determines its content (RFC-3095, section 5.2.6). The profile indicated in the IR-CR packet determines how it is to be processed. If the CRC (8-bit CRC) fails to verify the packet, the packet MUST be discarded. If the profile as indicated in the IR-CR packet defines the use of the Base CID and if its corresponding field is present within the packet format, this field is used to identify the base context; otherwise the CID is used. 3.4.2. Reconstruction and verification The decompressor creates a new context using the information present in the IR-CR packet together with the identified base context, and decompresses the original header. The CRC calculated over the original uncompressed header and carried within the profile specific part of the IR-CR headers (7-bit CRC) MUST be used to verify decompression. When the decompression is verified and successful, the decompressor initializes or update the context with the information received in the current header. The decompressor SHOULD send an ACK when it succeeds to validate the context as a result of the decompression of one or more IR-CR packets. Otherwise if the reconstructed header fails the CRC check, changes to the context MUST NOT be performed. When the decompressor fails to validate the header, actions as specified in section 3.4.3 are taken. 3.4.3. Actions upon failure For profiles supporting context replication, the feedback logic of a decompressor is similar to the logic used for context initialization, as described in [RFC-3095]. Pelletier [Page 9] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 Specifically, when the decompressor fails to validate the context following the decompression of one or more initial IR-CR packets, it MUST invalidate the context and remain in its initial state. In addition, the decompressor SHOULD send a STATIC-NACK. If the context has been successfully validated from the decompression of one or more initial IR-CR packets, the decompressor SHOULD send a NACK when it fails to verify the context following the decompression of one or more subsequent IR-CR packets. 3.5. Packet Formats The format of the IR-CR packet has been designed under the following constraints: a) it must be possible to either overwrite a CID during context replication, or to use a CID different than the Base CID for the replicated context; b) it must be possible to replicate from a base context using a profile different than the one associated with the replicated context, for fields specifically common to both profiles; c) it must be possible to selectively include or exclude from the packet format some fields that may be replicable; d) it must be possible for some fields that may be replicable to be represented within the packet format using either a compressed or an uncompressed form; e) it must be possible for the decompressor to verify the success of the replication procedure; f) it is anticipated that profiles other than [ROHC-TCP] will also define support for context replication, therefore it is desirable that the packet format be as profile independent as possible. 3.5.1. CRCs in the IR-CR packet The IR packet, as defined in [RFC-3095], is used to communicate static and/or dynamic parts of a context, and typically initialize the context. For example, the static and dynamic chains of IR packets may contain an uncompressed representation of the original header. The IR packet format includes an 8-bit CRC, calculated over the initial part of the IR packet. This CRC is meant to protect any information that initialize the context. In particular, its coverage always includes any CID information as well as the profile used to interpret the remainder of the IR packet. The purpose of the 8-bit CRC is to ensure the integrity of the IR header itself. Profiles may extend the coverage of this CRC to include the entire IR header, thus allowing the verification of the integrity of the entire uncompressed header. However because the format of the IR packet is common to all ROHC profiles and verified as part of the initial processing of a ROHC decompressor (see [RFC- Pelletier [Page 10] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 3095, section 5.2.6.]), profiles may not redefine this CRC beyond the extent of its coverage. [RFC-3095] also defines a 3-bit CRC and a 7-bit CRC for compressed headers, used to verify proper decompression and validate the context. This type of CRC is calculated over the original uncompressed header, as it is not sufficient to only protect the compressed data being exchanged between compressor and decompressor to ensure a robust reconstruction of the original header. There is thus a clear distinction in purposes between the 8-bit CRC found in the IR packet and the 3-bit or 7-bit CRC found in compressed headers. With context replication, where the IR-CR packet may contain both compressed as well as uncompressed information and omit entirely replicable fields, this distinction in no longer present. Profiles supporting context replication MUST define a CRC over the original uncompressed header as part of the profile specific information in the IR-CR packet. This is necessary to allow a decompressor to verify that the replication process has succeeded. 3.5.1.1. 7-bit CRC The 7-bit CRC in the IR-CR packet is calculated over all octets of the entire original header, before replication, in the same manner as described in [RFC-3095, section 5.9.2]. The initial content of the CRC register is to be preset to all 1's. The CRC polynomial used for the 7-bit CRC in the IR-CR is: C(x) = 1 + x + x^2 + x^3 + x^6 + x^7 3.5.1.2. 8-bit CRC The coverage of the 8-bit CRC in the IR-CR packet is not profile- dependent, as opposed to the ROHC IR(-DYN) packet [ROHC, section 5.2.3. and 5.2.4.]. It MUST cover the entire packet, excluding the payload. In particular, this includes the CID or any add-CID octet as well as the Base CID field, if present. For profiles that define the usage of the Base CID within the packet format of the IR-CR as optional, this CRC MUST also cover the information used to indicate the presence of this field within the packet. The initial content of the CRC register is to be preset to all 1's. The CRC polynomial used for the 8-bit CRC in the IR-CR is: C(x) = 1 + x + x^2 + x^8 Pelletier [Page 11] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 3.5.2. General format of the IR-CR packet The context replication mechanism requires a dedicated IR packet format that uniquely identifies the IR-CR packet. This packet communicates the static and the dynamic parts of the replicated context. It may also communicate a reference to a base context. With consideration to the extensibility of the IR packet type defined in [RFC-3095], support for replication can be added using the profile specific part of the IR packet. Note that there is one bit, (x), left in the IR header for "Profile specific information". The definition of this bit is profile-specific. Thus, profiles supporting context replication may use this bit as a flag indicating whether the packet is an IR packet or an IR-CR packet. Note also that profiles may define an alternative method to identify the IR-CR packet within the profile specific information, instead of using this bit. The IR-CR header associates a CID with a profile, and initializes the context using the context replication mechanism. It is not recommended to use this packet to repair a damaged context. The IR-CR has the following general format: 0 1 2 3 4 5 6 7 --- --- --- --- --- --- --- --- : Add-CID octet : if for small CIDs and (CID != 0) +---+---+---+---+---+---+---+---+ | 1 1 1 1 1 1 0 x | IR type octet +---+---+---+---+---+---+---+---+ : : / 0-2 octets of CID / 1-2 octets if for large CIDs : : +---+---+---+---+---+---+---+---+ | Profile | 1 octet +---+---+---+---+---+---+---+---+ | CRC | 1 octet +---+---+---+---+---+---+---+---+ | | / Profile specific information / variable length | | - - - - - - - - - - - - - - - - | | / Payload / variable length | | - - - - - - - - - - - - - - - - x: Profile specific information. Interpreted according to the profile indicated in the Profile field. Profile: The profile to be associated with the CID. In the IR-CR packet, the profile identifier is abbreviated to the Pelletier [Page 12] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 8 least significant bits. It selects the highest-number profile in the channel state parameter PROFILES that matches the 8 LSBs given (see also [RFC-3095]). CRC: 8-bit CRC computed using the polynomial of section 3.5.1.2. Profile specific information: The contents of this part of the IR-CR packet are defined by the individual profiles. This information is interpreted according to the profile indicated in the Profile field. It MUST include a 7-bit CRC over the original uncompressed header using the polynomial of section 3.5.1.1. It also includes the static and dynamic subheader information used for replication. Payload: The payload of the corresponding original packet, if any. 3.6. Inter-profile context replication <# Editor's Note: #> <# Open issue: How important is it to support Inter-profile #> <# context replication? Should this section be #> <# modified or removed? #> Inter-profile context replication requires that the decompressor has access to data structures from the base context, which belongs to a profile different than the profile using replication. This information must be available in a format consistent with the data structures and encoding method(s) in use for all fields being replicated. 3.6.1. Supporting inter-profile context replication A ROHC profile describes how to compress a specific protocol stack, and include one or more sets of packet formats. The packet formats will typically compress the protocol headers relative to a context of field values from previous headers in a flow. This context may also contain some control data. The packet formats thus specify a mapping between the uncompressed and compressed version of a protocol field. This mapping is achieved through the use of one or more encoding methods, which are simply functions applied to compress or decompress a field. An encoding method is in turn defined using a name, a set of function parameters and a formal expression (i.e. with [ROHC-FN]) or a textual description (i.e. a la [RFC-3095]) of its behaviour. To compress one or more fields of a specific protocol stack, different profiles may define their packet formats using different encoding methods, or using a variant of a similar technique. A typical example of the latter is list compression, such as used for IP extension headers. This implies that context entries for a field belonging to a specific protocol stack may differ in their content, representation and structure from one profile to another. Pelletier [Page 13] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 As a consequence of the above, a profile supporting context replication can only use a base context from another profile explicitly supporting the concept of a base context. That is, existing profiles not supporting this concept must be updated first to ensure that they can export the necessary context data entries using a meaningful representation during replication. Specifically, inter-profile context replication mandates that decompressor implementations (including existing ones) of other profiles be updated when adding support for a profile using context replication. Inter-profile context replication can therefore not be seen as being only a specific implementation issue. The compressor must know if the decompressor supports inter-profile context replication before initiating it. The compressor must also know which contexts belonging to what profile may be used as a base context. Therefore, a compressor MUST NOT initiate context replication using a base context belonging to a different profile, unless this profile explicitly provides the proper mapping for its context entries or unless this profile is defined formally using [ROHC-FN]. Profiles allowing the usage of the context as a base context can then be known by the compressor from the set of profiles negotiated for that channel (see also [RFC-3095]). 3.6.2. Compatibility between different profiles Inter-profile compatibility when replicating a field for a particular protocol stack is thus herein defined as a field using the same mapping function between its uncompressed and compressed version. For example, the IP Destination Address field which, based on the packet formats and compression strategies defined in [RFC-3095], is implicitly compressed using an encoding method equivalent to the static() method defined in [ROHC-FN]. In particular, for profiles defining their packet formats using the formal notation [ROHC-FN], two different encoding methods may not have the same name. A field from a protocol stack is thus said to be compatible for replication between two different profiles if it has an equivalent definition within the packet formats. 4. Security considerations This document does not bring any new additional security considerations than those already listed in [ROHC-TCP]. 5. Acknowledgements The author would like to thank Lars-Erik Jonsson, Richard Price, Mark West and HongBin Liao for valuable input to this document. Pelletier [Page 14] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 6. References 6.1. Normative references [RFC-3095] Bormann, C., Burmeister, C., Degermark, M., Fukushima, H., Hannu, H., Jonsson, L-E., Hakenberg, R., Koren, T., Le, K., Liu, Z., Martensson, A., Miyazaki, A., Svanbro, K., Wiebke, T., Yoshimura, T. and H. Zheng, "RObust Header Compression (ROHC): Framework and four profiles: RTP, UDP, ESP, and uncompressed", RFC 3095, July 2001. 6.2. Informative references [ROHC-TCP] Pelletier, G., Zhang, Q., Jonsson, L-E., Liao, H., West, M., "RObust Header Compression (ROHC): TCP/IP Profile (ROHC-TCP)", Internet Draft (work in progress), , May 2003. [TCP-REQ] Jonsson, L-E., "Requirements on ROHC IP/TCP header compression", Internet Draft (work in progress), , October 2002. [TCP-BEH] West, M. and S. McCann, "TCP/IP Field Behavior", Internet Draft (work in progress), , March 2003. [RFC-2026] Bradner, S., "The Internet Standards Process", RFC 2026, October 1996. [ROHC-FN] "Formal Notation for Robust Header Compression (ROHC-FN)", R. Price et al., (work in progress), March 2003 7. Author's address Ghyslain Pelletier Box 920 Ericsson AB SE-971 28 Lulea, Sweden Phone: +46 920 20 24 32 Fax: +46 920 20 20 99 Email: ghyslain.pelletier@epl.ericsson.se Pelletier [Page 15] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 Appendix A. General format of the IR-CR packet (informative) Appendix A.1. General structure (informative) This section provides an example of the format of the profile specific information within the general format of the IR-CR. 0 1 2 3 4 5 6 7 +---+---+---+---+---+---+---+---+ | | / replication base information / variable length | | +---+---+---+---+---+---+---+---+ | | / replication information / variable length | | - - - - - - - - - - - - - - - - Replication base information: The contents of this part of the IR-CR packet are defined by the individual profiles. This information is interpreted according to the profile indicated in the Profile field. It MUST include a 7-bit CRC over the original uncompressed header using the polynomial of section 3.4.1.1. See Appendix A.2. Replication information: The contents of this part of the IR-CR packet are also defined by the individual profiles. This part contains the static and dynamic subheader information used for replication. How this information is structured is profile specific; profiles may define the contents of this field using a chain structure (static and dynamic replication chains) or by defining header formats for replication (e.g. [ROHC-TCP]). Appendix A.2. Profile specific replication information (informative) This section provides a more detailed example of the possible format of the replication information field described in Appendix A.1: +---+---+---+---+---+---+---+---+ | B | CRC7 | 1 octet +---+---+---+---+---+---+---+---+ | | present if B = 1, / Base CID / 1 octet if for small CIDs, or | | 1-2 octets if for large CIDs +---+---+---+---+---+---+---+---+ B: B = 1 indicates that the Base CID field is present. CRC7: The CRC over the original, uncompressed, header. This 7-bit CRC is computed according to section 3.4.1.1. Base CID: The CID identifying the base context used for replication. Pelletier [Page 16] INTERNET-DRAFT Context Replication for ROHC profiles October 27, 2003 Full Copyright Statement Copyright (C) The Internet Society (2003). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This Internet-Draft expires April 27, 2004. Pelletier [Page 17]