Network Working Group M. Riegel Internet-Draft Siemens AG Expires: July 14, 2004 (Editor) January 14, 2004 Requirements for Edge-to-Edge Emulation of TDM Circuits over Packet Switching Networks (PSN) draft-ietf-pwe3-tdm-requirements-04.txt Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http:// www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on July 14, 2004. Copyright Notice Copyright (C) The Internet Society (2004). All Rights Reserved. Abstract This document specifies the specific requirements for edge-to-edge-emulation of circuits carrying time division multiplexed digital (TDM) signals of the PDH as well as the SONET/SDH hierarchy over packet-switched networks. It is aligned to the common architecture for Pseudo Wire Emulation Edge-to-Edge (PWE3) as defined in [PWE3-ARCH]. It makes references to requirements in [PWE3-REQ] where applicable and complements [PWE3-REQ] by defining requirements originating from specifics of TDM circuits. Riegel, et al. Expires July 14, 2004 [Page 1] Internet-Draft PWE3 TDM Requirements January 2004 Co-Authors The following are co-authors of this document: Sasha Vainshtein Axerra Networks Yaakov Stein RAD Data Communication Prayson Pate Overture Networks, Inc. Ron Cohen Lycium Networks Tim Frost Zarlink Semiconductor Changes from the last revision: - Editorial corrections Riegel, et al. Expires July 14, 2004 [Page 2] Internet-Draft PWE3 TDM Requirements January 2004 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 TDM circuits belonging to the PDH hierarchy . . . . . . . . 4 1.1.1 TDM structure and transport modes . . . . . . . . . . . . . 5 1.2 SONET/SDH circuits . . . . . . . . . . . . . . . . . . . . . 5 2. Motivation . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . 7 4. Reference Models . . . . . . . . . . . . . . . . . . . . . . 8 4.1 Generic PWE3 Models . . . . . . . . . . . . . . . . . . . . 8 4.2 Clock Recovery . . . . . . . . . . . . . . . . . . . . . . . 8 4.3 Network Synchronization Reference Model . . . . . . . . . . 8 4.3.1 Synchronous Network Scenarios . . . . . . . . . . . . . . . 11 4.3.2 Relative Network Scenario . . . . . . . . . . . . . . . . . 12 4.3.3 Adaptive Network Scenario . . . . . . . . . . . . . . . . . 13 5. Emulated Services . . . . . . . . . . . . . . . . . . . . . 14 5.1 Structure-Agnostic Transport of signals out of the PDH hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.2 Structure-Aware Transport of signals out of the PDH hierarchy . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.3 Structure-Aware Transport of SONET/SDH Circuits . . . . . . 15 6. Generic Requirements . . . . . . . . . . . . . . . . . . . . 15 6.1 Relevant Common PW Requirements . . . . . . . . . . . . . . 15 6.2 Common Circuit Payload Requirements . . . . . . . . . . . . 16 6.3 General Design Issues . . . . . . . . . . . . . . . . . . . 16 7. Service-Specific Requirements . . . . . . . . . . . . . . . 17 7.1 Interworking . . . . . . . . . . . . . . . . . . . . . . . . 17 7.2 Network Synchronization . . . . . . . . . . . . . . . . . . 17 7.3 Robustness . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.3.1 Packet loss . . . . . . . . . . . . . . . . . . . . . . . . 17 7.3.2 Out-of-order delivery . . . . . . . . . . . . . . . . . . . 18 7.4 CE Signaling . . . . . . . . . . . . . . . . . . . . . . . . 18 7.5 PSN bandwidth utilization . . . . . . . . . . . . . . . . . 19 7.6 Packet Delay Variation . . . . . . . . . . . . . . . . . . . 20 7.7 Compatibility with the Existing PSN Infrastructure . . . . . 20 7.8 Congestion Control . . . . . . . . . . . . . . . . . . . . . 20 7.9 Fault Detection and Handling . . . . . . . . . . . . . . . . 20 7.10 Performance Monitoring . . . . . . . . . . . . . . . . . . . 21 8. Security Considerations . . . . . . . . . . . . . . . . . . 21 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 21 9.1 Normative References . . . . . . . . . . . . . . . . . . . . 21 9.2 Informative References . . . . . . . . . . . . . . . . . . . 22 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . 23 Intellectual Property and Copyright Statements . . . . . . . 25 Riegel, et al. Expires July 14, 2004 [Page 3] Internet-Draft PWE3 TDM Requirements January 2004 1. Introduction This document specifies the specific requirements for edge-to-edge-emulation of circuits carrying time division multiplexed digital signals of the PDH as well as the SONET/SDH hierarchy over packet-switched networks. It is aligned to the common architecture for Pseudo Wire Emulation Edge-to-Edge (PWE3) as defined in [PWE3-ARCH]. It makes references to requirements in [PWE3-REQ] where applicable and complements [PWE3-REQ] by defining requirements originating from specifics of TDM circuits. The term "TDM" will be used in this documents as a general descriptor for the synchronous bit streams belonging to either the PDH or the SONET/SDH hierarchies. 1.1 TDM circuits belonging to the PDH hierarchy The bit rates traditionally used in various regions of the world are detailed in the normative reference [G.702]. For example, in North America the T1 bit stream of 1.544 Mbps and the T3 bit stream of 44.736 Mbps are mandated, while in Europe the E1 bit stream of 2.048 Mbps and the E3 bit stream of 34.368 Mbps are utilized. Although TDM can be used to carry unstructured bit streams at the rates defined in [G.702], there is a standardized method of carrying bit streams in larger units called frames, each frame containing the same number of bits. Related to the sampling frequency of voice traffic, there are always 8000 such frames per second, hence the T1 frame consists of 193 bits and the E1 frame of 256 bits. The number of bits in a frame is called the frame size. The framing is imposed by introducing a period pattern into the bit stream to identify the boundaries of the frames (e.g. 1 framing bit per T1 frame, a sequence of 8 framing bits per E1 frame). The details of how these framing bits are generated and used are elucidated in [G.704], [G.706] and [G.751]. Unframed TDM has all bits available for payload. Framed TDM is often used to multiplex multiple channels (e.g., voice channels each consisting of 8000 8bit-samples per second) in a sequence of "timeslots" recurring in the same position in each frame. This multiplexing is called "channelized TDM" and introduces additional structure. In some cases framing also defines groups of consecutive frames called multiframes. Such grouping imposes an additional level of Riegel, et al. Expires July 14, 2004 [Page 4] Internet-Draft PWE3 TDM Requirements January 2004 structure on the TDM bit-stream. 1.1.1 TDM structure and transport modes Unstructured TDM: TDM that consists of a raw bit-stream of rate defined in [G.702], with all bits are available for payload. Structured TDM: TDM with one ore more levels of structure delineation, including frames, channelization, and multiframes (e.g. as defined in [G.704], [G.751], [T1.107]). Structure-Agnostic Transport: Transport of unstructured TDM, or of structured TDM when the structure is deemed inconsequential from the transport point of view. In structure-agnostic transport any structural overhead that may be present is transparently transported along with the payload data, and the encapsulation provides no mechanisms for its location or utilization. Structure-Aware Transport: Transport of structured TDM taking at least some level of the structure into account. In structure-aware transport there is no guarantee that all bits of the TDM bit-stream will be actually transported over the MPLS network (specifically, the synchronization bits and related overhead may be stripped at ingress and usually will be regenerated at egress), or that bits transported are always situated in the packet in their original order. 1.2 SONET/SDH circuits The term SONET refers to the North American Synchronous Optical NETwork as specified by [T1.105]. It is based on the concept of a Nx783 byte payload container repeated every 125us. This payload is referred as an STS-1 SPE and may be concatenated into higher bandwidth circuits (e.g. STS-Nc) or sub-divided into lower bandwidth circuits (Virtual Tributaries). The higher bandwidth concatenated circuits can be used to carry anything from IP Packets to ATM cells to Digital Video Signals. Individual STS-1 SPEs are frequently used to carry individual DS3 or E3 TDM circuits. When the 783 byte containers are sub-divided for lower rate payloads, they are frequently used to carry individual T1 or E1 TDM circuits. The Synchronous Digital Hierarchy (SDH) is the international equivalent and enhancement of SONET and is specified by [G.707]. Both SONET and SDH include a substantial amount of transport overhead Riegel, et al. Expires July 14, 2004 [Page 5] Internet-Draft PWE3 TDM Requirements January 2004 that is used for performance monitoring, fault isolation, and other maintenance functions along different types of optical or electrical spans. This also includes a pointer based mechanism for carrying payload asynchronously. In addition, the payload area includes dedicated overhead for end-to-end performance monitoring, fault isolation, and maintenance for the service being carried. If the main payload area is sub-divided into lower rate circuits (such as T1/E1), additional overhead is included for end-to-end monitoring of the individual T1/E1 circuits. This document discusses the requirements for emulation of SONET/SDH services. These services include end-to-end emulation of the SONET payload (STS-1 SPE), emulation of concatenated payloads (STS-Nc SPE), as well as emulation of a variety of sub-STS-1 rate circuits jointly referred to as Virtual Tributaries (VT) and their SDH analogs. 2. Motivation [PWE3-REQ] specifies common requirements for edge-to-edge-emulation of circuits of various types. However, these requirements, as well as references in [PWE3-ARCH] do not cover specifics of PWs carrying TDM circuits. The need for a specific document complementing [PWE3-REQ] addressing edge-to-edge-emulation of TDM circuits arises from following: o Specifics of the TDM circuits, e.g.: * the need for balance between the clock of ingress and egress attachment circuits in each direction of the PW, * the need to maintain jitter and wander of the clock of the egress end service within the limits imposed by the appropriate normative documents in spite of the packet delay variation produced by the PSN. o Specifics of applications using TDM circuits, e.g. voice applications: * put special emphasis on minimization of one-way delay, * are relatively tolerant to errors in data. Other applications might have different specifics. e.g. transport of signaling information: * is relatively tolerant to one-way delay, Riegel, et al. Expires July 14, 2004 [Page 6] Internet-Draft PWE3 TDM Requirements January 2004 * is sensitive to errors in transmitted data. o Specifics of the customers' expectations regarding end-to-end behavior of services that contain emulated TDM circuits, e.g., experience with carrying such services over SONET/SDH networks increases the need for: * isolation of problems introduced by the PSN from those occurring beyond the PSN bounds, * sensitivity to misconnection, * sensitivity to unexpected connection termination, etc. 3. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. The terms defined in [PWE3-ARCH], Section 1.4 are consistently used. However some terms and acronyms are specific in conjunction with the TDM services. In particular: TDM networks employ CAS or CCS signaling to supervise and advertise status of telephony applications, provide alerts to these applications (as to requests to connect or disconnect), and to transfer routing and addressing information. These signals must be reliably transported over the PSNs for the telephony end-systems to function properly. CAS (Channel-Associated Signaling) CAS is carried in the same T1 or E1 frame as the voice signals, but not in the speech band. Since CAS signaling may be transferred at a rate slower than the TDM traffic in a timeslot, one need not update all the CAS bits every TDM frame. Hence CAS systems cycle through all the signaling bits only after some number of TDM frames, defining a new structure known as a multiframe or superframe. Common multiframes are 12, 16, or 24 frames in length, corresponding to 1.5, 2 and 3 milliseconds in duration. CCS (Common Channel Signaling) CCS signaling uses a separate digital channel to carry asynchronous messages pertaining to the state of telephony applications over related TDM timeslots of a TDM trunk. This channel may be physically situated in one or more adjacent timeslots of the same TDM trunk (trunk associated CCS) or may be Riegel, et al. Expires July 14, 2004 [Page 7] Internet-Draft PWE3 TDM Requirements January 2004 transported over an entirely separate network. CCS is typically HDLC-based, with idle codes or keep-alive messages being sent until a signaling event (e.g. on-hook or off-hook) occurs. Examples of HDLC-based CCS systems are SS7 [Q.700] and ISDN PRI signaling [Q.931]. Note: For the TDM network we use the terms "jitter" and "wander" as defined in [G.810] to describe short- and long-term variance of the significant instants of the digital signal, while for the PSN we use the term packet delay variation (PDV) (see [RFC3393]). 4. Reference Models 4.1 Generic PWE3 Models Generic models that have been defined in [PWE3-ARCH] in Sections - 4.1 (Network Reference Model), - 4.2 (PWE3 Pre-processing), - 4.3 (Maintenance Reference Model), - 4.4 (Protocol Stack Reference Model) and - 4.5 (Pre-processing Extension to Protocol Stack Reference Model). They are fully applicable for the purposes of this document without modification. All the services considered in this document represent special cases of the Bit-stream and Structured bit-stream payload type defined in Section 3.3 of [PWE3-ARCH]. 4.2 Clock Recovery Clock recovery is extraction of the transmission bit timing information from the delivered packet stream. Extraction of this information from a highly jittered source such as a packet stream may be a complex task. 4.3 Network Synchronization Reference Model A generic network synchronization reference model is shown in Figure 1 below: Riegel, et al. Expires July 14, 2004 [Page 8] Internet-Draft PWE3 TDM Requirements January 2004 +---------------+ +---------------+ | PE1 | | PE2 | K | +--+ | | +--+ | G | | | J| | | | H| | | v | v | | | v | | v +---+ | +-+ +-+ +-+ | +--+ +--+ | +-+ +-+ +-+ | +---+ | | | |P| |D| |P| | | | | | | |P| |E| |P| | | | | |<===|h|<:|e|<:|h|<:::| |<::| |<:::|h|<:|n|<=|h|<===| | | | | |y| |c| |y| | | | | | | |y| |c| |y| | | | | C | | +-+ +-+ +-+ | | | | | | +-+ +-+ +-+ | | C | | E | | | |S1| |S2| | | | E | | 1 | | +-+ +-+ +-+ | | | | | | +-+ +-+ +-+ | | 2 | | | | |P| |E| |P| | | | | | | |P| |D| |P| | | | | |===>|h|=>|n|:>|h|:::>| |::>| |:::>|h|:>|e|=>|h|===>| | | | | |y| |c| |y| | | | | | | |y| |c| |y| | | | +---+ | +-+ +-+ +-+ | +--+ +--+ | +-+ +-+ +-+ | +---+ ^ ^ | | ^ ^ ^ | | | ^ | ^ ^ | | | |B | | | |<------+------>| | | | | | | A | +--+ +--+ | | | +--+-E | F | | +---------------+ +-+ +---------------+ | | ^ |I| ^ | | | +-+ | | | C D | +-----------------------------L-----------------------------+ Figure 1: The Network Synchronization Reference Model The following notation is used in Figure 1: CE1, CE2 Customer edge devices terminating TDM circuits to be emulated. PE1, PE2 Provider edge devices adapting these end services to PW. S1, S2 Provider core routers Phy Physical interface terminating the TDM circuit. Enc PSN-bound interface of the PW Dec CE-bound interface of the PW. It contains a compensation buffer (also known as the "jitter buffer") of limited size. Riegel, et al. Expires July 14, 2004 [Page 9] Internet-Draft PWE3 TDM Requirements January 2004 "==>" TDM attachment circuits "::>" PW providing edge-to-edge-emulation for the TDM circuit. The characters "A" - "L" denote various clocks: "A" The clock used by CE1 for transmission of the TDM attachment circuit towards CE1. "B" The clock recovered by PE1 from the incoming TDM attachment circuit. "A" and "B" always have the same frequency. "G" The clock used by CE2 for transmission of the TDM attachment circuit towards CE2. "H" The clock recovered by PE2 from the incoming TDM attachment circuit. "G" and "H" always have the same frequency. "C", "D" Local oscillators available to PE1 and PE2 respectively. "E" Clock used by PE2 to transmit the TDM attachment service circuit to CE2 (the recovered clock). "F" Clock recovered by CE2 from the incoming TDM attachment service ("E and "F" have the same frequency). "I" If the clock exists, it is the common network reference clock available to PE1 and PE2. "J" Clock used by PE1 to transmit the TDM attachment service circuit to CE1 (the recovered clock). "K" Clock recovered by CE1 from the incoming TDM attachment service ("J" and "K" have the same frequency). Riegel, et al. Expires July 14, 2004 [Page 10] Internet-Draft PWE3 TDM Requirements January 2004 "L" If it exists, it is the common reference clock of CE1 and CE2. Note that different pairs of CE devices may use different common reference clocks. A requirement of edge-to-edge-emulation of a TDM circuit is that clock "B" and "E" are of the same frequency. The most appropriate method will depend on the network synchronization scheme. The following groups of synchronization scenarios can be considered: 4.3.1 Synchronous Network Scenarios Depending on which part of the network is synchronized by a common clock there are two scenarios: o PE Synchronized Network: Figure 2 below, an adapted version of the generic network reference model, presents the PE synchronized network scenario. The common network reference clock "I" is available to all the PE devices, and local oscillators "C" and "D" are locked to "I": * Clocks "E" and "J" are the same as "D" and "C" respectively. * Clocks "A" and "G" are the same as "K" and "F" respectively (i.e., CE1 and CE2 use loop timing). +-----+ +-----+ +-----+ | |- - -|=================|- - -| | +-----+ | /-- |<---------|............PW1..............|<---------| <-\ | || CE | | | PE1 | | PE2 | | |CE2 || | \-> |--------->|............PW2..............|--------->| --/ | +-----+ | |- - -|=================|- - -| | +-----+ +-----+ +-----+ ^ ^ |C |D +-----------+-----------+ | +-+ |I| +-+ Figure 2: PE synchronized scenario Riegel, et al. Expires July 14, 2004 [Page 11] Internet-Draft PWE3 TDM Requirements January 2004 o CE Synchronized Network: Figure 3 below, an adapted version of the generic network reference model, presents the CE synchronized network scenario. The common network reference clock "L" is available to all the CE devices, and local oscillators "A" and "G" are locked to "L": * Clocks "E" and "J" are the same as "G" and "A" respectively (i.e., PE1 and PE2 use loop timing). +-----+ +-----+ +-----+ | |- - -|=================|- - -| | +-----+ | |<---------|............PW1..............|<---------| | | CE1 | | | PE1 | | PE2 | | | CE2 | | |--------->|............PW2..............|--------->| | +-----+ | |- - -|=================|- - -| | +-----+ ^ +-----+ +-----+ ^ |A G| +----------------------------+------------------------------+ | +-+ |L| +-+ Figure 3: CE synchronized scenario No timing information has to be transferred in these cases. 4.3.2 Relative Network Scenario In this case each CE uses its own transmission clock source that must be carried across the PSN and recovered by the remote PE, respectively. The common PE clock "I" can be used as reference for this purpose. Figure 4 below shows the relative network scenario. The common network reference clock "I" is available to all the PE devices, and local oscillators "C" and "D" are locked to "I": o Clocks "A" and "G" are generated locally without reference to a common clock. o Clocks "E" and "J" are generated in reference to a common clock available at all PE devices. Riegel, et al. Expires July 14, 2004 [Page 12] Internet-Draft PWE3 TDM Requirements January 2004 In a slight modification of this scenario, one (but not both!) of the CE devices may use its receive clock as its transmission clock (i.e. use loop timing). |G +-----+ +-----+ v +-----+ | |- - -|=================|- - -| | +-----+ | |<---------|............PW1..............|<---------| | | CE1 | | | PE1 | | PE2 | | | CE2 | | |--------->|............PW2..............|--------->| | +-----+ | |- - -|=================|- - -| | +-----+ ^ +-----+<-------+------->+-----+ |A | +-+ |I| +-+ Figure 4: Relative network scenario Timing information (the difference between the common reference clock "I" and the incoming like clock "A") MUST be explicitly transferred in this case from the ingress PE to the egress PE. 4.3.3 Adaptive Network Scenario The adaptive scenario is characterized by: o No common network reference clock "I" is available to PE1 and PE2. o No common reference clock "L" is available to CE1 and CE2. Figure 5 below presents the adaptive network scenario. |J |G v | +-----+ +-----+ v +-----+ | |- - -|=================|- - -| | +-----+ | |<---------|............PW1..............|<---------| | | CE1 | | | PE1 | | PE2 | | | CE2 | | |--------->|............PW2..............|--------->| | +-----+ | |- - -|=================|- - -| | +-----+ ^ +-----+ +-----+ | ^ A| E| Figure 5: Adaptive scenario Riegel, et al. Expires July 14, 2004 [Page 13] Internet-Draft PWE3 TDM Requirements January 2004 Synchronizing clocks "A" and "E" in this scenario is more difficult than it is in the other scenarios. Note that the tolerance between clocks "A" and "E" must be small enough to ensure that the jitter buffer does not overflow or underflow. Timing information MAY be explicitly transferred in this case from the ingress PE to the egress PE, e. g. by RTP. 5. Emulated Services This section defines requirements for the payload and encapsulation layers for edge-to-edge emulation of TDM services with bit-stream payload as well as structured bit-stream payload. Wherever possible, the requirements specified in this document SHOULD be satisfied by appropriate arrangements of the encapsulation layer only. The (rare) cases when the requirements apply to both the encapsulation and payload layers (or even only to the payload layer only) will be explicitly noted. The service-specific encapsulation layer for edge-to-edge emulation comprises the following services over a PSN. 5.1 Structure-Agnostic Transport of signals out of the PDH hierarchy Structure-agnostic transport is considered for the following signals: o E1 as described in [G.704]. o T1 (DS1) as described in [G.704]. o E3 as defined in [G.751]. o T3 (DS3) as described in [T.107]. 5.2 Structure-Aware Transport of signals out of the PDH hierarchy Structure-aware transport is considered for the following signals: o E1/T1 with one of the structures imposed by framing as described in [G.704] o NxDS0 with or without CAS Riegel, et al. Expires July 14, 2004 [Page 14] Internet-Draft PWE3 TDM Requirements January 2004 5.3 Structure-Aware Transport of SONET/SDH Circuits Structure-aware transport is considered for the following SONET/SDH circuits: o SONET STS-1 synchronous payload envelope (SPE)/SDH VC-3 o SONET STS-Nc SPE (N = 3, 12, 48, 192) / SDH VC-4, VC-4-4c, VC-4-16c, VC-4-64c o SONET VT-N (N = 1.5, 2, 3, 6) / SDH VC-11, VC-12, VC-2 o SONET Nx VT-N / SDH Nx VC-11/VC-12/VC-2/VC-3 Note: There is no requirement for the structure-agnostic transport of SONET/SDH. It would seem that structure must be taken into account for this case. 6. Generic Requirements 6.1 Relevant Common PW Requirements The encapsulation and payload layers must conform to the common PW requirements defined in [PWE3-REQ]: 1. Conveyance of Necessary Header Information: 1. For structure-agnostic transport, this functionality MAY be provided by the payload layer. 2. For structure-aware transport, the necessary information MUST be provided by the encapsulation layer. 3. Structure-aware transport of SONET/SDH circuits MUST preserve path overhead information as part of the payload. Relevant components of the transport overhead MAY be carried in the encapsulation layer. 2. Support of Multiplexing and Demultiplexing if supported by the native services: 1. Relevant for Nx DS0 circuits with or without signaling and Nx VT-x in a single STS-1 SPE or VC-4. 2. For these circuits the combination of encapsulation and payload layers MUST provide for separate treatment of every sub-circuit. Riegel, et al. Expires July 14, 2004 [Page 15] Internet-Draft PWE3 TDM Requirements January 2004 3. Enough information SHOULD be provided by the pseudo wire to allow multiplexing and demultiplexing by the NSP. Reduction of the complexity of the PW emulation by using NSP circuitry for multiplexing and demultiplexing MAY be the preferred solution. 3. Intervention or transparent transfer of Maintenance Messages of the Native Services depending on the particular scenario. 4. Consideration of Per-PSN Packet Overhead (see also Section 7.5 below). 5. Detection and handling of PW faults. The list of faults is given in Section 7.9 below. 6. Fragmentation indications MAY be used for structure-aware transport when the structures in question either exceed desired packetization delay or exceed Path MTU between the pair of PEs. The following requirement listed in [PWE3-REQ] is not applicable to emulation of TDM services: o Support of variable length PDUs. 6.2 Common Circuit Payload Requirements Structure-agnostic transport treats TDM circuits as belonging to the 'Bit-stream' payload type defined in [PWE3-ARCH]. Structure-aware transport treats these circuits as belonging to the "Structured bit-stream" payload type defined in [PWE3-ARCH]. Accordingly, the encapsulation layer MUST provide the common Sequencing service and SHOULD provide Timing information (Synchronization services) when required (see Section 4.3 above). Note: Length service MAY be provided by the encapsulation layer but is not required. 6.3 General Design Issues The combination of payload and encapsulation layers SHOULD comply with the general design principles of the Internet protocols as presented in [RFC1958], Section 3 and [PWE3-ARCH]. If necessary, the payload layer MAY use some forms of adaptation of the native TDM payload in order to achieve specific well-documented Riegel, et al. Expires July 14, 2004 [Page 16] Internet-Draft PWE3 TDM Requirements January 2004 design objectives. In these cases standard adaptation techniques SHOULD be used. 7. Service-Specific Requirements 7.1 Interworking 1. The emulation MUST support network interworking between ACs of the same type (see Section 5) and, wherever appropriate, bit-rate. 2. The encapsulation layer SHOULD remain unaffected by specific characteristics of connection between the ACs and PE devices at the two ends of the PW. 7.2 Network Synchronization 1. The encapsulation layer MUST provide synchronization services that are sufficient to: 1. match the ingress and egress end service clocks regardless of the specific network synchronization scenario, 2. keep the jitter and wander of the egress service clock within the service-specific limits as defined by the appropriate normative references. 2. If the same high-quality synchronization source is available to all the PE devices in the given domain, the encapsulation layer SHOULD be able to make use of it (e.g., for better reconstruction of the native service clock). 7.3 Robustness The robustness of the emulated service depends not only upon the edge-to-edge-emulation protocol but also upon proper implementation of the following procedures. 7.3.1 Packet loss Edge-to-edge-emulation of TDM circuits MAY assume very low probability of packet loss between ingress and egress PE. In particular, no retransmission mechanisms are required. In order to minimize effect of lost packets on the egress service, the encapsulation layer SHOULD: Riegel, et al. Expires July 14, 2004 [Page 17] Internet-Draft PWE3 TDM Requirements January 2004 1. Enable independent interpretation of TDM data in each packet by the egress PE (see [RFC2736]). This requirement MAY be disregarded if the egress PE needs to interpret structures that exceed the path MTU between the ingress and egress PEs. 2. Allow reliable detection of lost packets (see next section). In particular, it SHOULD allow estimation of the arrival time of the next packet and detection of lost packets based on this estimate. 3. Minimize possible effect of lost packets on recovery of the circuit clock by the egress PE. 4. Increase the resilience of the CE TDM interface to packet loss by allowing the egress PE to substitute appropriate data. 7.3.2 Out-of-order delivery The encapsulation layer MUST provide the necessary mechanisms to guarantee ordered delivery of packets carrying the TDM data over the PSN. Packets that have arrived out-of-order: 1. MUST be detected, 2. SHOULD be reordered if not judged to be too late or too early for playout. Out-of-order packets that cannot be reordered MUST be treated as lost. 7.4 CE Signaling Unstructured TDM circuits would not usually require any special mechanism for carrying CE signaling as this would be carried as part of the emulated service. Some CE applications using structured TDM circuits (e.g., telephony) require specific signaling that conveys changes of state of these applications relative to the TDM data. The encapsulation layer SHOULD support signaling of state of CE applications for the relevant circuits providing for: 1. Ability to support different signaling schemes with minimal impact on encapsulation of TDM data, 2. Multiplexing of application-specific CE signals and data of the emulated service in the same PW, Riegel, et al. Expires July 14, 2004 [Page 18] Internet-Draft PWE3 TDM Requirements January 2004 3. Synchronization (within the application-specific tolerance limits) between CE signals and data at the PW egress, 4. Probabilistic recovery against possible occasional loss of packets in the PSN, 5. Deterministic recovery of the CE application state after PW setup and network outages. CE signaling that is used for maintenance purposes (loopback commands, performance monitoring data retrieval, etc.) SHOULD use the generic PWE3 maintenance protocol. 7.5 PSN bandwidth utilization 1. The encapsulation layer SHOULD allow for an effective trade-off between the following requirements: 1. Effective PSN bandwidth utilization. Assuming that the size of encapsulation layer header does not depend on the size of its payload, increase in the packet payload size results in increased efficiency. 2. Low edge-to-edge latency. Low end-to-end latency is the common requirement for Voice applications over TDM services. Packetization latency is one of the components comprising edge- to-edge latency and decreases with the packet payload size. The compensation buffer used by the CE-bound IWF increases latency to the emulated circuit. Additional delay introduced by this buffer SHOULD NOT exceed the packet delay variation observed in the PSN. 2. The encapsulation layer MAY provide for saving PSN bandwidth by not sending corrupted TDM data across the PSN. 3. The encapsulation layer MAY provide the ability to save the PSN bandwidth for the structure-aware case by not sending channels that are permanently inactive. 4. The encapsulation layer MAY enable the dynamic suppression of temporarily unused channels from transmission for the structure-aware case. If used, dynamic suppression of temporarily unused channels MUST NOT violate integrity of the structures delivered over the PW. Riegel, et al. Expires July 14, 2004 [Page 19] Internet-Draft PWE3 TDM Requirements January 2004 5. For NxDS0 the encapsulation layer MUST provide the ability to keep the edge-to-edge delay independent of the service rate. 7.6 Packet Delay Variation The encapsulation layer SHOULD provide for ability to compensate for packet delay variation while maintaining jitter and wander of the egress end service clock with tolerances specified in the normative references. The encapsulation layer MAY provide for run-time adaptation of delay introduced by the jitter buffer if the packet delay variation varies with time. Such an adaptation MAY introduce a low level of errors (within the limits tolerated by the application) but SHOULD NOT introduce additional wander of the egress end service clock. 7.7 Compatibility with the Existing PSN Infrastructure The combination of encapsulation and PSN tunnel layers used for edge-to-edge emulation of TDM circuits SHOULD be compatible with existing PSN infrastructures. In particular, compatibility with the mechanisms of header compression over links where capacity is at a premium SHOULD be provided. 7.8 Congestion Control TDM circuits run at a constant rate, and hence offer constant traffic loads to the PSN. The rate varying mechanism that TCP uses to match demand to the network congestion state is therefore not applicable. The ability to shut down a TDM PW when congestion has been detected MUST be provided. Precautions should be taken to avoid situations wherein multiple TDM PWs are simultaneously shut down or re-established, thus leading to PSN instability. Further congestion considerations are discussed in chapter 6.5 of [PWE3-ARCH]. 7.9 Fault Detection and Handling The encapsulation layer for edge-to-edge emulation of TDM services SHOULD, separately or in conjunction with the lower layers of the PWE3 stack, provide for detection, handling and reporting of the following defects: Riegel, et al. Expires July 14, 2004 [Page 20] Internet-Draft PWE3 TDM Requirements January 2004 1. Misconnection, or Stray Packets. The importance of this requirement stems from customer expectation due to reliable misconnection detection in SONET/SDH networks. 2. Packet Loss. Packet loss detection required in order to maintain clock integrity, as discussed in Section 7.3.1 above. In addition, packet loss detection mechanisms SHOULD provide for localization of the outage in the end-to-end emulated service. 3. Malformed packets. 7.10 Performance Monitoring The encapsulation layer for edge-to-edge emulation of TDM services SHOULD provide for collection of performance monitoring (PM) data that is compatible with the parameters defined for 'classic', TDM- based carriers of these services. The applicability of [G.826] is left for further study. 8. Security Considerations The security considerations listed in [PWE3-REQ] fully apply also to the emulation of TDM circuits. 9. References 9.1 Normative References [PWE3-REQ] draft-ietf-pwe3-requirements-07.txt XiPeng Xiao et al, Requirements for Pseudo Wire Emulation Edge-to- Edge (PWE3), Work in Progress, October 2003 [PWE3-ARCH] draft-ietf-pwe3-arch-06.txt Stewart Bryant et al, PWE3 Architecture, Work in progress, October 2003 [G.702] ITU-T Recommendation G.702 (11/88) - Digital hierarchy bit rates [G.704] ITU-T Recommendation G.704 (10/98) - Synchronous frame structures used at 1544, 6312, 2048, 8448 and 44 736 Kbit/s hierarchical levels [G.706] ITU-T Recommendation G.706 (04/91) - Frame alignment and cyclic redundancy check (CRC) procedures relating to basic frame structures defined in Recommendation G.704 [G.707] ITU-T Recommendation G.707 (10/00) - Network node interface Riegel, et al. Expires July 14, 2004 [Page 21] Internet-Draft PWE3 TDM Requirements January 2004 for the synchronous digital hierarchy (SDH) [G.751] ITU-T Recommendation G.751 (11/88) - Digital multiplex equipments operating at the third order bit rate of 34 368 Kbit/s and the fourth order bit rate of 139 264 Kbit/s and using positive justification [G.810] ITU-T Recommendation G.810 (08/96) - Definitions and terminology for synchronization networks [RFC1958] B. Carpenter (ed.), Architectural Principles of the Internet, RFC 1958, IETF, 1996 [RFC2119] S.Bradner, Key Words in RFCs to Indicate Requirement Levels, RFC 2119, IETF, 1997 [RFC2736] M. Handley, C. Perkins, Guidelines for Writers of RTP Payload Format Specifications, RFC 2736, IETF, 1999 [RFC3393] C. Demichelis, P. Chimento, IP Packet Delay Variation Metric for IPPM, RFC 3393, IETF, 2002 [T1.105] ANSI T1.105 - 2001 Synchronous Optical Network (SONET) - Basic Description including Multiplex Structure, Rates, and Formats, May 2001 [T1.107] ANSI T1.107 - 1995. Digital Hierarchy - Format Specification 9.2 Informative References [G.826] ITU-T Recommendation G.826 (02/99) - Error performance parameters and objectives for international, constant bit rate digital paths at or above the primary rate [Q.700] ITU-T Recommendation Q.700 (03/93) - Introduction to CCITT Signalling System No. 7 [Q.931] ITU-T Recommendation Q.931 (05/98) - ISDN user-network interface layer 3 specification for basic call control Riegel, et al. Expires July 14, 2004 [Page 22] Internet-Draft PWE3 TDM Requirements January 2004 Authors' Addresses Maximilian Riegel Siemens AG St-Martin-Str 76 Munich 81541 Germany Phone: +49-89-636-75194 EMail: maximilian.riegel@siemens.com Alexander (Sasha) Vainshtein Axerra Networks 24 Raoul Wallenberg St. Tel Aviv 69719 Israel Phone: +972-3-7569993 EMail: sasha@axerra.com Yaakov (Jonathan) Stein RAD Data Communications 24 Raoul Wallenberg St., Bldg. C Tel Aviv 69719 Israel Phone: +972-3-645-5389 EMail: yaakov_s@rad.com Prayson Pate Overture Networks, Inc. 507 Aviation Blvd, Suite 111 Morrisville, NC 27560 USA EMail: prayson.pate@overturenetworks.com Riegel, et al. Expires July 14, 2004 [Page 23] Internet-Draft PWE3 TDM Requirements January 2004 Ron Cohen Lycium Networks 14 Hatidhar st. Raanana 43000 Israel Phone: +972-9-7619004 EMail: ronc@lyciumnetworks.com Tim Frost Zarlink Semiconductor Tamerton Road Roborough, Plymouth PL6 7BQ UK EMail: tim.frost@zarlink.com Riegel, et al. Expires July 14, 2004 [Page 24] Internet-Draft PWE3 TDM Requirements January 2004 Intellectual Property Statement The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in BCP-11. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. Full Copyright Statement Copyright (C) The Internet Society (2004). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assignees. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION Riegel, et al. Expires July 14, 2004 [Page 25] Internet-Draft PWE3 TDM Requirements January 2004 HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Acknowledgment Funding for the RFC Editor function is currently provided by the Internet Society. Riegel, et al. Expires July 14, 2004 [Page 26]