Network Working Group J. Asghar Internet-Draft IJ. Wijnands, Ed. Intended status: Standards Track S. Krishnaswamy Expires: October 28, 2016 A. Karan Cisco Systems V. Arya DIRECTV Inc. April 26, 2016 Explicit RPF Vector draft-ietf-pim-explicit-rpf-vector-09.txt Abstract The PIM Reverse Path Forwarding (RPF) Vector TLV defined in RFC 5496 can be included in a PIM Join Attribute such that the RPF neighbor is selected based on the unicast reachability of the RPF Vector instead of the Source or Randezvous Point associated with the multicast tree. This document defines a new RPF Vector Attribute type such that an explicit RPF neighbor list can be encoded in the PIM Join Attribute, bypassing the unicast route lookup. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on October 28, 2016. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents Asghar, et al. Expires October 28, 2016 [Page 1] Internet-Draft Explicit RPF Vector April 2016 (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Specification of Requirements . . . . . . . . . . . . . . . . 3 3. Motivation . . . . . . . . . . . . . . . . . . . . . . . . . 3 4. Use of the PIM Explicit RPF Vector . . . . . . . . . . . . . 4 5. Explicit RPF Vector Attribute TLV Format . . . . . . . . . . 4 6. Mixed Vector Processing . . . . . . . . . . . . . . . . . . . 5 7. Conflicting RPF Vectors . . . . . . . . . . . . . . . . . . . 5 8. PIM Asserts . . . . . . . . . . . . . . . . . . . . . . . . . 6 9. Join Suppression . . . . . . . . . . . . . . . . . . . . . . 6 10. Unsupported Explicit Vector Handling . . . . . . . . . . . . 6 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 6 12. Security Considerations . . . . . . . . . . . . . . . . . . . 7 13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 7 14. References . . . . . . . . . . . . . . . . . . . . . . . . . 7 14.1. Normative References . . . . . . . . . . . . . . . . . . 7 14.2. Informative References . . . . . . . . . . . . . . . . . 8 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8 1. Introduction The procedures in [RFC5496] define how a RPF vector can be used to influence the path selection in the absence of a route to the source. The same procedures can be used to override a route to the source when it exists. It is possible to include multiple RPF vectors in the list where each router along the path will perform a unicast route lookup on the first vector in the attribute list. Once the router owning the address of the RPF vector is reached, following the procedures in [RFC5496], the RPF vector will be removed from the attribute list. This will result in a 'loosely' routed path that still depends on unicast reachability to the RPF vector(s). In some scenarios the network adminstrators don't want to rely on the unicast reachability to the RPF vector address and want to build a path strictly based on the RPF vectors. In that case the RPF vectors represent a list of directly connected PIM neighbors along the path. For these vectors the router would not do a route lookup in the unicast routing table. These vectors are referred to as 'Explicit' RPF Vector addresses. If a router receiving an Explicit RPF Vector Asghar, et al. Expires October 28, 2016 [Page 2] Internet-Draft Explicit RPF Vector April 2016 does not have a PIM neighbor matching the Explicit RPF Vector address, it does not fall back to loosely routing the join. Instead, it could process the packet and store the RPF Vector list so that the PIM join can be sent out as soon as the neighbor comes up. Since the behavior of the Explicit RPF Vector differs from the loose RPF vector as defined [RFC5496], a new attribute called the Explicit RPF Vector is defined. This document defines a new TLV in the PIM Join Attribute message [RFC5384] for specifying the explicit path. 2. Specification of Requirements The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 3. Motivation Some broadcast video transport networks use a multicast PIM Live-Live resiliency model for video delivery based on PIM SSM or PIM ASM. Live-Live implies using 2 active spatially diverse multicast trees to transport video flows from root to leaf multicast routers. The leaf multicast router receives 2 copies from the PIM multicast core and will replicate 1 copy towards the receivers [RFC7431]. One of the requirements of the PIM Live-Live resiliency model is to ensure path-diversity of the 2 active PIM trees in the core such that they do not intersect to avoid a single point of failure. IGP routed RPF paths of 2 PIM trees could be routed over the same transit router and create a single point of failure. It is useful to have a way to specify the explicit path along which the PIM join is propagated. How the Explicit RPF Vector list is determined is outside the scope of this document. For example, it may either be manually configured by the network operator or procedures may be implemented on the egress router to dynamically calculate the vector list based on a link state database protocol, like OSPF or IS-IS. Due to the fact that the leaf router receives two copies of the multicast stream via two diverse paths, there is no need for PIM to repair the broken path immediately. It is up to the egress router to either wait for the broken path to be repaired or build a new explicit path using a new RPF vector list. Which method is applied depends very much on how the vector list was determined initially. Double failures are not considered and are outside the scope of this document. Asghar, et al. Expires October 28, 2016 [Page 3] Internet-Draft Explicit RPF Vector April 2016 This document describes the procedures to carry Explicit RPF vectors in PIM. It is up to the mechanism(s) that produce the Explicit RPF Vectors to ensure they are correct. Existing mechanisms like [I-D.ietf-mboned-mtrace-v2] may be used to verify how the PIM tree was build. 4. Use of the PIM Explicit RPF Vector Figure 1 provides an example multicast join path R4->R3->R6->R5->R2->R1, where the multicast join is explicitly routed to the source hop-by-hop using the Explicit RPF Vector list. When R5-R6 link fails the join will NOT take an alternate path. [S]---(R1)--(R2)---(R3)--(R4)---[R] <--- | | --- | | | | | (R5)---(R6) | - (S,G) Join - | | | | (R7)---(R8) Figure 1 In comparison, when [RFC5496] procedures are used, if R5-R6 link fails then the join may be re-routed using R6-R8-R7 path to reach R5. 5. Explicit RPF Vector Attribute TLV Format 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |F|E| Type | Length | Value +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-....... Figure 2 F bit: The F bit MUST be set to 0. Otherwise there could be loops. E bit: End of Attributes. If this bit is set then this is the last TLV specified in the list. Type: The Vector Attribute type is TBD1. Length: Length depending on the Address Family (IPv4 or IPv6) of the Encoded-Unicast address. Asghar, et al. Expires October 28, 2016 [Page 4] Internet-Draft Explicit RPF Vector April 2016 Value: Encoded-Unicast address. This SHOULD be a valid IPv4 or IPv6 address of an upstream router. 6. Mixed Vector Processing Explicit RPF Vector attribute does not impact or restrict the functionality of other RPF vector attributes in a PIM join. It is possible to mix vectors of different types, such that some part of the tree is explicit and other parts are loosely routed. RPF vectors are processed in the order in which they are specified. 7. Conflicting RPF Vectors It is possible that a PIM router has multiple downstream neighbors. If for the same multicast route there is an inconsistency between the Explicit RPF Vector lists provided by the downstream PIM neighbor, the procedures as documented in section 3.3.3 [RFC5384] apply. The conflict resolution procedures in section 3.3.3 [RFC5384] only apply to attributes of the same Join Attribute type. Join Attributes that have a different type can't be compared because the content of the Join Attribute may have a totally different meaning and/or encoding. This may cause a problem if a mix of Explicit RPF Vectors (this document) and 'loose' RPF vectors [RFC5496] is received from two or more downstream routers. The order in which the RPF vectors are encoded may be different and/or the combination of RPF vectors may be inconsistent. The procedures in section 3.3.3 [RFC5384] would not resolve the conflict. The following procedures MUST be applied to deal with this scenario. When a PIM Join with Join Attribute list is received from a downstream neighbor, the router MUST verify that the order in which the RPF Vector types appear in the PIM Join Attribute list matches what is stored as the Join Attribute list for reaching the Source or Randezvous point listed in the PIM Join. Once it is determined that the RPF Vector types on the stack are equal, the content of the RPF Vectors MUST be compared ([RFC5384]). If it is determined that there is either a conflict with RPF Vector types or the RPF Vector content, the router uses the RPF Vector stack from the PIM adjacency with numerically smallest IP address. In the case of IPv6, the link local address will be used. When two neighbors have the same IP address, either for IPv4 or IPv6, the interface index MUST be used as a tie breaker. It's RECOMMENDED that the router doing the conflict resolution log a message. Asghar, et al. Expires October 28, 2016 [Page 5] Internet-Draft Explicit RPF Vector April 2016 8. PIM Asserts Section 3.3.3 of [RFC5496] specifies the procedures for how to deal with PIM asserts when RPF vectors are used. The same procedures apply to the Explicit RPF Vector. There is minor behavioral difference, the route metric that is included in the PIM Assert should be the route metric of the first Explicit RPF vector address in the list. However, the first Explicit vector should always be directly connected, so the Metric may likely be zero. The Metric will therefore not be a tie breaker in the PIM Assert selection procedure. 9. Join Suppression Section 3.3.4 of [RFC5496] specifies the procedures how to apply join suppression when an RPF Vector attribute is included in the PIM join. The same procedure applies to the Explicit RPF Vector attribute. The procedure MUST match against all the Explicit RPF Vectors in the PIM join before a PIM join can be suppressed. 10. Unsupported Explicit Vector Handling The F bit MUST be set to 0 in all Explicit RPF vectors in case the upstream router receiving the join does not support the TLV. As described in section 3.3.2 of [RFC5384], routers that do not understand the type of a particular attribute that has the F bit clear will discard it and continue to process the join. This processing is particularly important when the routers that do not support the Explicit RPF TLV are identified as hops in the explicit RPF list, because failing to remove the RPF vectors could cause upstream routers to send the join back toward these routers causing loops. As the administrator is manually specifying the path that the joins need to be sent on, it is recommended that the administrator computes the path to include routers that support explcit vector and check that the state is created correctly on each router along the path. Tools like mtrace can be used for debugging and to ensure that the join state is setup correctly. 11. IANA Considerations A new attribute (TBD1) type from the "PIM Join Attribute Types" registry needs to be assigned by IANA for the Explicit RPF Vector attribute. The proposed value 4. Asghar, et al. Expires October 28, 2016 [Page 6] Internet-Draft Explicit RPF Vector April 2016 12. Security Considerations Security of the Explicit RPF Vector Attribute is only guaranteed by the security of the PIM packet, so the security considerations for PIM Join packets as described in PIM-SM [I-D.ietf-pim-rfc4601bis] apply here. A malicious downstream node can attempt a denial of service attack by sending PIM Join packets with invalid addresses listed in the RPF vector stack with an intent to stop the propogation of the joins to the correct upstream node. Another denial of service attack would be a malicious downstream node targeting all joins to a specific node with an intent to overload the bandwidth on that node by making it responsible for forwarding multicast traffic for more streams that it can handle. Inorder to minimize the risk of a denial of service attacks from forged PIM join packets with explicit RPF vector stack, it should be used within a single trusted management domain. If a router finds that it cannot use the vector list due to the next hop router not being a PIM neighbor, it may log an error. Also if a router is receiving two conflicting vectors it may log an error. It is upto the mechanisms that produced the Explicit RPF vector to ensure that the the PIM tree is built correctly and to monitor any error logs. 13. Acknowledgments The authors would like to thank Vatsa Kumar, Nagendra Kumar and Bharat Joshi for the comments on the document. 14. References 14.1. Normative References [I-D.ietf-pim-rfc4601bis] Fenner, B., Handley, M., Holbrook, H., Kouvelas, I., Parekh, R., Zhang, J., and L. Zheng, "Protocol Independent Multicast - Sparse Mode (PIM-SM): Protocol Specification (Revised)", draft-ietf-pim-rfc4601bis-06 (work in progress), August 2015. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . Asghar, et al. Expires October 28, 2016 [Page 7] Internet-Draft Explicit RPF Vector April 2016 [RFC5384] Boers, A., Wijnands, I., and E. Rosen, "The Protocol Independent Multicast (PIM) Join Attribute Format", RFC 5384, DOI 10.17487/RFC5384, November 2008, . [RFC5496] Wijnands, IJ., Boers, A., and E. Rosen, "The Reverse Path Forwarding (RPF) Vector TLV", RFC 5496, DOI 10.17487/RFC5496, March 2009, . 14.2. Informative References [I-D.ietf-mboned-mtrace-v2] Asaeda, H., Meyer, K., and W. Lee, "Mtrace Version 2: Traceroute Facility for IP Multicast", draft-ietf-mboned- mtrace-v2-12 (work in progress), October 2015. [RFC7431] Karan, A., Filsfils, C., Wijnands, IJ., Ed., and B. Decraene, "Multicast-Only Fast Reroute", RFC 7431, DOI 10.17487/RFC7431, August 2015, . Authors' Addresses Javed Asghar Cisco Systems 725, Alder Drive Milpitas CA 95035 USA Email: jasghar@cisco.com IJsbrand Wijnands (editor) Cisco Systems De Kleetlaan 6a Diegem 1831 Belgium Email: ice@cisco.com Asghar, et al. Expires October 28, 2016 [Page 8] Internet-Draft Explicit RPF Vector April 2016 Sowmya Krishnaswamy Cisco Systems 3750 Cisco Way San Jose CA 95134 USA Email: sowkrish@cisco.com Apoorva Karan Cisco Systems 3750 Cisco Way San Jose CA 95134 USA Email: apoorva@cisco.com Vishal Arya DIRECTV Inc. 2230 E Imperial Hwy El Segundo CA 90245 USA Email: varya@directv.com Asghar, et al. Expires October 28, 2016 [Page 9]