NTP Working Group D. Sibold Internet-Draft PTB Intended status: Standards Track S. Roettger Expires: January 5, 2015 K. Teichel PTB July 04, 2014 Network Time Security draft-ietf-ntp-network-time-security-04.txt Abstract This document describes the Network Time Security (NTS) protocol that enables secure authentication of time servers using Network Time Protocol (NTP) or Precision Time Protocol (PTP). Its design considers the special requirements of precise timekeeping, which are described in Security Requirements of Time Protocols in Packet Switched Networks [I-D.ietf-tictoc-security-requirements]. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on January 5, 2015. Sibold, et al. Expires January 5, 2015 [Page 1] Internet-Draft NTS July 2014 Copyright Notice Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Security Threats . . . . . . . . . . . . . . . . . . . . . . 4 3. Objectives . . . . . . . . . . . . . . . . . . . . . . . . . 4 4. Terms and Abbreviations . . . . . . . . . . . . . . . . . . . 5 5. NTS Overview . . . . . . . . . . . . . . . . . . . . . . . . 5 5.1. Symmetric and Client/Server Mode . . . . . . . . . . . . 5 5.2. Broadcast Mode . . . . . . . . . . . . . . . . . . . . . 6 6. Protocol Messages . . . . . . . . . . . . . . . . . . . . . . 6 6.1. Association Messages . . . . . . . . . . . . . . . . . . 6 6.1.1. Message Type: "client_assoc" . . . . . . . . . . . . 7 6.1.2. Message Type: "server_assoc" . . . . . . . . . . . . 7 6.2. Certificate Messages . . . . . . . . . . . . . . . . . . 7 6.2.1. Message Type: "client_cert" . . . . . . . . . . . . . 8 6.2.2. Message Type: "server_cert" . . . . . . . . . . . . . 8 6.3. Cookie Messages . . . . . . . . . . . . . . . . . . . . . 9 6.3.1. Message Type: "client_cook" . . . . . . . . . . . . . 9 6.3.2. Message Type: "server_cook" . . . . . . . . . . . . . 9 6.4. Unicast Time Synchronisation Messages . . . . . . . . . . 10 6.4.1. Message Type: "time_request" . . . . . . . . . . . . 10 6.4.2. Message Type: "time_response" . . . . . . . . . . . . 10 6.5. Broadcast Parameter Messages . . . . . . . . . . . . . . 11 6.5.1. Message Type: "client_bpar" . . . . . . . . . . . . . 11 6.5.2. Message Type: "server_bpar" . . . . . . . . . . . . . 11 6.6. Broadcast Message . . . . . . . . . . . . . . . . . . . . 12 6.6.1. Message Type: "server_broad" . . . . . . . . . . . . 12 7. Protocol Sequence . . . . . . . . . . . . . . . . . . . . . . 13 7.1. The Client . . . . . . . . . . . . . . . . . . . . . . . 13 7.1.1. The Client in Unicast Mode . . . . . . . . . . . . . 13 7.1.2. The Client in Broadcast Mode . . . . . . . . . . . . 15 7.2. The Server . . . . . . . . . . . . . . . . . . . . . . . 16 7.2.1. The Server in Unicast Mode . . . . . . . . . . . . . 16 Sibold, et al. Expires January 5, 2015 [Page 2] Internet-Draft NTS July 2014 7.2.2. The Server in Broadcast Mode . . . . . . . . . . . . 17 8. Server Seed Considerations . . . . . . . . . . . . . . . . . 17 8.1. Server Seed Refresh . . . . . . . . . . . . . . . . . . . 17 8.2. Server Seed Algorithm . . . . . . . . . . . . . . . . . . 17 8.3. Server Seed Lifetime . . . . . . . . . . . . . . . . . . 17 9. Hash Algorithms and MAC Generation . . . . . . . . . . . . . 17 9.1. Hash Algorithms . . . . . . . . . . . . . . . . . . . . . 17 9.2. MAC Calculation . . . . . . . . . . . . . . . . . . . . . 18 10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 18 11. Security Considerations . . . . . . . . . . . . . . . . . . . 18 11.1. Initial Verification of the Server Certificates . . . . 18 11.2. Revocation of Server Certificates . . . . . . . . . . . 19 11.3. Usage of NTP Pools . . . . . . . . . . . . . . . . . . . 19 11.4. Denial-of-Service in Broadcast Mode . . . . . . . . . . 19 11.5. Delay Attack . . . . . . . . . . . . . . . . . . . . . . 19 12. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 20 13. References . . . . . . . . . . . . . . . . . . . . . . . . . 20 13.1. Normative References . . . . . . . . . . . . . . . . . . 20 13.2. Informative References . . . . . . . . . . . . . . . . . 21 Appendix A. Flow Diagrams of Client Behaviour . . . . . . . . . 22 Appendix B. Extension Fields . . . . . . . . . . . . . . . . . . 25 Appendix C. TICTOC Security Requirements . . . . . . . . . . . . 25 Appendix D. Broadcast Mode . . . . . . . . . . . . . . . . . . . 26 D.1. Server Preparations . . . . . . . . . . . . . . . . . . . 27 D.2. Client Preparation . . . . . . . . . . . . . . . . . . . 28 D.3. Sending Authenticated Broadcast Packets . . . . . . . . . 29 D.4. Authentication of Received Packets . . . . . . . . . . . 29 Appendix E. Random Number Generation . . . . . . . . . . . . . . 30 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 30 1. Introduction Time synchronization protocols are increasingly utilized to synchronize clocks in networked infrastructures. The reliable performance of such infrastructures can be degraded seriously by successful attacks against the time synchronization protocol. Therefore, time synchronization protocols applied in critical infrastructures have to provide security measures to defeat possible adversaries. Consequently, the widespread Network Time Protocol (NTP) [RFC5905] was supplemented by the autokey protocol [RFC5906] which shall ensure authenticity of the NTP server and integrity of the protocol packets. Unfortunately, the autokey protocol exhibits various severe security vulnerabilities as revealed in a thorough analysis of the protocol [Roettger]. For the Precision Time Protocol (PTP), Annex K of the standard document IEEE 1588 [IEEE1588] defines an informative security protocol that is still in experimental state. Sibold, et al. Expires January 5, 2015 [Page 3] Internet-Draft NTS July 2014 Because of autokey's security vulnerabilities and the absence of a standardized security protocol for PTP, these protocols cannot be applied in environments in which compliance requirements demand authenticity and integrity protection. This document specifies a security protocol which ensures authenticity of the time server via a Public Key Infrastructure (PKI) and integrity of the time synchronization protocol packets and which therefore enables the usage of NTP and PTP in such environments. The protocol is specified with the prerequisite in mind that precise timekeeping can only be accomplished with stateless time synchronization communication, which excludes the utilization of standard security protocols like IPsec or TLS for time synchronization messages. This prerequisite corresponds with the requirement that a security mechanism for timekeeping must be designed in such a way that it does not degrade the quality of the time transfer [I-D.ietf-tictoc-security-requirements]. Note: The intent is to formulate the protocol to be applicable to NTP and also PTP. In the current state the draft focuses on the application to NTP. 2. Security Threats A profound analysis of security threats and requirements for NTP and PTP can be found in the "Security Requirements of Time Protocols in Packet Switched Networks" [I-D.ietf-tictoc-security-requirements]. 3. Objectives The objectives of the NTS specification are as follows: o Authenticity: NTS enables the client to authenticate its time server. o Integrity: NTS protects the integrity of time synchronization protocol packets via a message authentication code (MAC). o Confidentiality: NTS does not provide confidentiality protection of the time synchronization packets. o Modes of operation: All operational modes of NTP are supported. o Operational modes of PTP should be supported as far as possible. Sibold, et al. Expires January 5, 2015 [Page 4] Internet-Draft NTS July 2014 o Hybrid mode: Both secure and insecure communication modes are possible for NTP servers and clients, respectively. o Compatibility: * Unsecured NTP associations shall not be affected. * An NTP server that does not support NTS shall not be affected by NTS authentication requests. 4. Terms and Abbreviations MITM Man In The Middle NTP Network Time Protocol NTS Network Time Security PTP Precision Time Protocol TESLA Timed Efficient Stream Loss-Tolerant Authentication 5. NTS Overview 5.1. Symmetric and Client/Server Mode NTS applies X.509 certificates to verify the authenticity of the time server and to exchange a symmetric key, the so-called cookie. This cookie is then used to protect authenticity and integrity of the subsequent time synchronization packets by means of a Message Authentication Code (MAC), which is attached to each time synchronization packet. The calculation of the MAC includes the whole time synchronization packet and the cookie which is shared between client and server. It is calculated according to: cookie = MSB_128 (HMAC(server seed, H(certificate of client))), with the server seed as key, where H is a hash function, and where the function MSB_128 cuts off the 128 most significant bits of the result of the HMAC function. The server seed is a 128 bit random value of the server, which has to be kept secret. The cookie never changes as long as the server seed stays the same, but the server seed has to be refreshed periodically in order to provide key freshness as required in [I-D.ietf-tictoc-security-requirements]. See Section 8 for details on the seed refresh and Section 7.1.1 for the client's reaction to it. Sibold, et al. Expires January 5, 2015 [Page 5] Internet-Draft NTS July 2014 The server does not keep a state of the client. Therefore it has to recalculate the cookie each time it receives a request from the client. To this end, the client has to attach the hash value of its certificate to each request (see Section 6.4). 5.2. Broadcast Mode Just as in the case of the client server mode and symmetric mode, authenticity and integrity of the NTP packets are ensured by a MAC, which is attached to the NTP packet by the sender. The verification of the authenticity is based on the TESLA protocol, in particular on its "Not Re-using Keys" scheme, see section 3.7.2 of [RFC4082]. TESLA is based on a one-way chain of keys, where each key is the output of a one-way function applied on the previous key in the chain. The last element of the chain is shared securely with all clients. The server splits time into intervals of uniform duration and assigns each key to an interval in reverse order, starting with the penultimate. At each time interval, the server sends an NTP broadcast packet appended by a MAC, calculated using the corresponding key, and the key of the previous disclosure interval. The client verifies the MAC by buffering the packet until the disclosure of the key in its associated disclosure interval. In order to be able to verify the validity of the key, the client has to be loosely time synchronized to the server. This has to be accomplished during the initial client server exchange between broadcast client and server. For a more detailed description of the TESLA protocol see Appendix D. 6. Protocol Messages Note that this section currently describes the realization of the message format of NTS only for its utilization for NTP, in which the NTS specific data are enclosed in extension fields on top of NTP packets. A specification of NTS messages for PTP would have to be developed accordingly. The steps described in Section 6.1 - Section 6.4 belong to the unicast mode, while Section 6.5 and Section 6.6 explain the steps involved in the broadcast mode of NTS. 6.1. Association Messages In this message exchange, the hash and signature algorithms that are used throughout the protocol are negotiated. Sibold, et al. Expires January 5, 2015 [Page 6] Internet-Draft NTS July 2014 6.1.1. Message Type: "client_assoc" The protocol sequence starts with the client sending an association message, called client_assoc. This message contains o the NTS message ID "client_assoc", o the version number of NTS that the client wants to use (this SHOULD be the highest version number that it supports), o the hostname of the client, o a selection of accepted hash algorithms, o a selection of accepted encryption algorithms, and o a selection of accepted algorithms for the signatures. For NTP, this message is realized as a packet with an extension field of type "association", which contains all this data. 6.1.2. Message Type: "server_assoc" This message is sent by the server upon receipt of client_assoc. It contains o the NTS message ID "server_assoc", o the version number used for the rest of the protocol (which SHOULD be determined as the minimum over the client's suggestion in the client_assoc message and the highest supported by the server), o the hostname of the server, and o the server's choice of algorithm for encryption, for the signatures and for cryptographic hashing , all of which MUST be chosen from the client's proposals. In the case of NTP, the data is enclosed in a packet's extension field, also of type "association". 6.2. Certificate Messages In this message exchange, the client receives the certification chain up to a trusted anchor. With the established certification chain the client is able to verify the server's signatures and, hence, authenticity of future NTS messages from the server is ensured. Sibold, et al. Expires January 5, 2015 [Page 7] Internet-Draft NTS July 2014 Discussion: Note that in this step the client validates the authenticity of its immediate NTP server only. It does not recursively validate the authenticity of each NTP server on the time synchronization chain. Recursive authentication (and authorization) as formulated in [I-D.ietf-tictoc-security-requirements] depends on the chosen trust anchor. 6.2.1. Message Type: "client_cert" This message is sent by the client, after it successfully verified the content of the received server_assoc message (see Section 7.1.1). It contains o the NTS message ID "client_cert", o the negotiated version number, o the client's hostname, and o the signature algorithm negotiated during the association messages. In the case of NTP, the data is enclosed in a packet's extension field of type "certificate request". 6.2.2. Message Type: "server_cert" This message is sent by the server, upon receipt of a client_cert message, if the version number and choice of methods communicated in that message are actually supported by the server. It contains o the NTS message ID "server_cert", o the version number as transmitted in client_cert, o a signature, calculated over the data listed above, with the server's private key and according to the signature algorithm transmitted in server_cert, o all the information necessary to authenticate the server to the client. This is a chain of certificates, which starts at the server and goes up to a trusted authority, where each certificate MUST be certified by the one directly following it. This message is realized for NTP as a packet with extension field of type "certificate" which holds all of the data listed above. Sibold, et al. Expires January 5, 2015 [Page 8] Internet-Draft NTS July 2014 6.3. Cookie Messages During this message exchange, the server transmits a secret cookie to the client securely. The cookie will be used for integrity protection during unicast time synchronization. 6.3.1. Message Type: "client_cook" This message is sent by the client, upon successful authentication of the server. In this message, the client requests a cookie from the server. The message contains o the NTS message ID "client_cook", o the negotiated version number, o the negotiated signature algorithm, o the negotiated encryption algorithm, o a 128-bit nonce, o the negotiated hash algorithm H, o the client's certificate. For NTP, an extension field of type "cookie request" holds the listed data. 6.3.2. Message Type: "server_cook" This message is sent by the server, upon receipt of a client_cook message. The server generates the hash of the client's certificate, as conveyed during client_cook, in order to calculate the cookie according to Section 5.1. This message contains a concatenated datum, which is encrypted with the client's public key, according to the encryption algorithm transmitted in the client_cook message. The concatenated datum contains o the NTS message ID "server_cook" o the version number as transmitted in client_cook, o the nonce transmitted in client_cook, o the cookie, and Sibold, et al. Expires January 5, 2015 [Page 9] Internet-Draft NTS July 2014 o a signature, created with the server's private key, calculated over * all of the data listed above, and also * the hash of the client's certificate. This signature MUST be calculated according to the transmitted signature algorithm from the client_cook message. In the case of NTP, this is a packet with an extension field of type "cookie transmit". 6.4. Unicast Time Synchronisation Messages In this message exchange, the usual time synchronization process is executed, with the addition of integrity protection for all messages that the server sends. This message can be repeatedly exchanged as often as the client desires and as long as the integrity of the server's time responses is verified successfully. 6.4.1. Message Type: "time_request" This message is sent by the client when it requests time exchange. It contains o the NTS message ID "time_request", o the negotiated version number, o a 128-bit nonce, o the negotiated hash algorithm H, o the hash of the client's certificate under H. In the case of NTP the data is enclosed in the packet's extension field of type "time request". 6.4.2. Message Type: "time_response" This message is sent by the server, after it received a time_request message. Prior to this the server MUST recalculate the client's cookie by using the hash of the client's certificate and the transmitted hash algorithm. The message contains o the NTS message ID "time_response", Sibold, et al. Expires January 5, 2015 [Page 10] Internet-Draft NTS July 2014 o the version number as transmitted in time_request, o the server's time synchronization response data, o the nonce transmitted in time_request, o a MAC (generated with the cookie as key) for verification of all of the above data. In the case of NTP, this is a packet with the necessary time synchronization data and a new extension field of type "time response". This packet has an appended MAC that is generated over the time synchronization data and the extension field, with the cookie as the key. 6.5. Broadcast Parameter Messages In this message exchange, the client receives the necessary information to execute the TESLA protocol in a secured broadcast association. The client can only initiate a secure broadcast association after a successful unicast run, see Section 7.1.2. See Appendix D for more details on TESLA. 6.5.1. Message Type: "client_bpar" This message is sent by the client in order to establish a secured time broadcast association with the server. It contains o the NTS message ID "client_bpar", o the version number negotiated during association in unicast mode, o the client's hostname, and o the signature algorithm negotiated during unicast. For NTP, this message is realized as a packet with an extension field of type "broadcast request". 6.5.2. Message Type: "server_bpar" This message is sent by the server upon receipt of a client_bpar message during the broadcast loop of the server. It contains o the NTS message ID "server_bpar", o the version number as transmitted in the client_bpar message, Sibold, et al. Expires January 5, 2015 [Page 11] Internet-Draft NTS July 2014 o the one-way function used for building the one-way key chain, o the last key of the one-way key chain, and o the disclosure schedule of the keys. This contains: * time interval duration, * the disclosure delay (number of intervals between use and disclosure of a key), * the time at which the next time interval will start, and * the next interval's associated index. o The message also contains a signature signed by the server with its private key, verifying all the data listed above. It is realized for NTP as a packet with an extension field of type "broadcast parameters", which contains all the given data. 6.6. Broadcast Message Via this message, the server keeps sending broadcast time synchronization messages to all participating clients. 6.6.1. Message Type: "server_broad" This message is sent by the server over the course of its broadcast schedule. It is part of any broadcast association. It contains o the NTS message ID "server_broad", o the version number that the server's broadcast mode is working under, o time broadcast data, o the index that belongs to the current interval (and therefore identifies the current, yet undisclosed key), o the disclosed key of the previous disclosure interval (current time interval minus disclosure delay), o a MAC, calculated with the key for the current time interval, verifying * the message ID, Sibold, et al. Expires January 5, 2015 [Page 12] Internet-Draft NTS July 2014 * the version number, and * the time data. For NTP, this message is realized as an NTP broadcast packet with the time broadcast data and with an extension field of type "broadcast message", which contains the rest of the listed data. The NTP packet is then appended by a MAC verifying its contents. 7. Protocol Sequence 7.1. The Client 7.1.1. The Client in Unicast Mode For a unicast run, the client performs the following steps: 1. It sends a client_assoc message to the server. It MUST keep the transmitted values for version number and algorithms available for later checks. 2. It waits for a reply in the form of a server_assoc message. After receipt of the message it performs the following checks: * The client checks that the message contains a conform version number. * It also has to verify that the server has chosen the signature and hash algorithms from its proposal sent in the client_assoc message. If one of the checks fails, the client MUST abort the run. 3. The client then sends a client_cert message to the server. Again, it MUST remember the transmitted values for version number and algorithms for later checks. 4. It awaits a reply in the form of a server_cert message and performs authenticity checks on the certificate chain and the signature for the version number. If one of these checks fails, the client MUST abort the run. 5. Next, it sends a client_cook message to the server. The client MUST save the included nonce until the reply has been processed. 6. It awaits a reply in the form of a server_cook message; upon receipt it executes the following actions: Sibold, et al. Expires January 5, 2015 [Page 13] Internet-Draft NTS July 2014 * It decrypts the message with its own private key. * It checks that the decrypted message is of the expected format: the concatenation of version number, a 128 bit nonce, a 128 bit cookie and a signature value. * It verifies that the received version number matches the one negotiated before. * It verifies that the received nonce matches the nonce sent in the client_cook message. * It verifies the signature using the server's public key. The signature has to authenticate the version number, the nonce, the cookie, and the hash of the client's certificate. If one of those checks fails, the client MUST abort the run. 7. The client sends a time_request message to the server. The client MUST save the included nonce and the transmit_timestamp (from the time synchronization data) as a correlated pair for later verification steps. 8. It awaits a reply in the form of a time_response message. Upon receipt, it checks: * that the transmitted version number matches the one negotiated before, * that the transmitted nonce belongs to a previous time_request message, * that the transmit_timestamp in that time_request message matches the corresponding time stamp from the synchronization data received in the time_response, and * that the appended MAC verifies the received synchronization data, version number and nonce. If at least one of the first three checks fails (i.e. if the version number does not match, if the client has never used the nonce transmitted in the time_response message or if it has used the nonce with initial time synchronization data different from that in the response), then the client MUST ignore this time_response message. If the MAC is invalid, the client MUST do one of the following: abort the run or go back to step 5 (because the cookie might have changed due to a server seed refresh). If Sibold, et al. Expires January 5, 2015 [Page 14] Internet-Draft NTS July 2014 both checks are successful, the client SHOULD continue time synchronization by going back to step 7. The client's behavior in unicast mode is also expressed in Figure 1. 7.1.2. The Client in Broadcast Mode To establish a secure broadcast association with a broadcast server, the client MUST initially authenticate the broadcast server and securely synchronize its time to it up to an upper bound for its time offset in unicast mode. After that, the client performs the following steps: 1. It sends a client_bpar message to the server. It MUST remember the transmitted values for version number and signature algorithm. 2. It waits for a reply in the form of a server_bpar message after which it performs the following checks: * The message must contain all the necessary information for the TESLA protocol, as listed in Section 6.5.2. * Verification of the message's signature. If any information is missing or the server's signature cannot be verified, the client MUST abort the broadcast run. If all checks are successful, the client MUST remember all the broadcast parameters received for later checks. 3. The client awaits time synchronization data in the form of a server_broadcast message. Upon receipt, it performs the following checks: 1. Proof that the MAC is based on a key that is not yet disclosed. This is achieved via a disclosure schedule and requires the loose time synchronization. If verified, the packet will be buffered for later authentication. Otherwise, the client MUST discard it. Note that the time information included in the packet will not be used for synchronization until its authenticity could be verified. 2. The client checks whether it already knows the disclosed key. If so, the client SHOULD discard the packet to avoid a buffer overrun. If not, the client verifies that the disclosed key belongs to the one-way key chain by applying the one-way function until equality with a previous disclosed key is verified. If falsified, the client MUST discard the packet. Sibold, et al. Expires January 5, 2015 [Page 15] Internet-Draft NTS July 2014 3. If the disclosed key is legitimate the client verifies the authenticity of any packet that it received during the corresponding time interval. If authenticity of a packet is verified it is released from the buffer and the packet's time information can be utilized. If the verification fails authenticity is no longer given. In this case the client MUST request authentic time from the server by means of a unicast time request message. See RFC 4082[RFC4082] for a detailed description of the packet verification process. The client MUST restart the broadcast sequence with a client_bpar message Section 6.5.1 if the one-way key chain expires. The client's behavior in broadcast mode can also be seen in Figure 2. 7.2. The Server 7.2.1. The Server in Unicast Mode To support unicast mode, the server MUST be ready to perform the following actions: o Upon receipt of a client_assoc message, the server constructs and sends a reply in the form of a server_assoc message as described in Section 6.1.2. o Upon receipt of a client_cert message, the server checks whether it supports the given signature algorithm. If so, it constructs and sends a server_cert message as described in Section 6.2.2. o Upon receipt of a client_cook message, the server checks whether it supports the given cryptographic algorithms. It then calculates the cookie according to the formula given in Section 5.1. With this, it MUST construct a server_cook message as described in Section 6.3.2. o Upon receipt of a time_request message, the server re-calculates the cookie, then computes the necessary time synchronization data and constructs a time_response message as given in Section 6.4.2. The server MUST refresh its server seed periodically (see Section 8.1). Sibold, et al. Expires January 5, 2015 [Page 16] Internet-Draft NTS July 2014 7.2.2. The Server in Broadcast Mode A broadcast server MUST also support unicast mode, in order to provide the initial time synchronization which is a precondition for any broadcast association. To support NTS broadcast, the server MUST additionally be ready to perform the following actions: o Upon receipt of a client_bpar message, the server constructs and sends a server_bpar message as described in Section 6.5.2. o The server follows the TESLA protocol in all other aspects, by regularly sending server_broad messages as described in Section 6.6.1, adhering to its own disclosure schedule. It is also the server's responsibility to watch for the expiration date of the one-way key chain and generate a new key chain accordingly. 8. Server Seed Considerations The server has to calculate a random seed which has to be kept secret. The server MUST generate a seed for each supported hash algorithm, see Section 9.1. 8.1. Server Seed Refresh According to the requirements in [I-D.ietf-tictoc-security-requirements] the server MUST refresh each server seed periodically. As a consequence, the cookie memorized by the client becomes obsolete. In this case the client cannot verify the MAC attachted to subsequent time response messages and has to respond accordingly by re-initiating the protocol with a cookie request (Section 6.3). 8.2. Server Seed Algorithm 8.3. Server Seed Lifetime 9. Hash Algorithms and MAC Generation 9.1. Hash Algorithms Hash algorithms are used at different points: calculation of the cookie and the MAC, and hashing of the client's certificate. Client and server negotiate a hash algorithm H during the association message exchange (Section 6.1) at the beginning of a unicast run. The selected algorithm H is used for all hashing processes in that run. Sibold, et al. Expires January 5, 2015 [Page 17] Internet-Draft NTS July 2014 In broadcast mode, hash algorithms are used as pseudo random functions to construct the one-way key chain. Here, the utilized hash algorithm is communicated by the server and non-negotiable. The list of the hash algorithms supported by the server has to fulfill the following requirements: o it MUST NOT include SHA-1 or weaker algorithms, o it MUST include SHA-256 or stronger algorithms. Note Any hash algorithm is prone to be compromised in the future. A successful attack on a hash algorithm would enable any NTS client to derive the server seed from their own cookie. Therefore, the server MUST have separate seed values for its different supported hash algorithms. This way, knowledge gained from an attack on a hash algorithm H can at least only be used to compromise such clients who use hash algorithm H as well. 9.2. MAC Calculation For the calculation of the MAC, client and server are using a Keyed- Hash Message Authentication Code (HMAC) approach [RFC2104]. The HMAC is generated with the hash algorithm specified by the client (see Section 9.1). 10. IANA Considerations 11. Security Considerations 11.1. Initial Verification of the Server Certificates The client has to verify the validity of the certificates during the certification message exchange (Section 6.2). Since it generally has no reliable time during this initial communication phase, it is impossible to verify the period of validity of the certificates. Therefore, the client MUST use one of the following approaches: o The validity of the certificates is preconditioned. Usually this will be the case in corporate networks. o The client ensures that the certificates are not revoked. To this end, the client uses the Online Certificate Status Protocol (OCSP) defined in [RFC6277]. Sibold, et al. Expires January 5, 2015 [Page 18] Internet-Draft NTS July 2014 o The client requests a different service to get an initial time stamp in order to be able to verify the certificates' periods of validity. To this end, it can, e.g., use a secure shell connection to a reliable host. Another alternative is to request a time stamp from a Time Stamping Authority (TSA) by means of the Time-Stamp Protocol (TSP) defined in [RFC3161]. 11.2. Revocation of Server Certificates According to Section 8.1, it is the client's responsibility to initiate a new association with the server after the server's certificate expires. To this end the client reads the expiration date of the certificate during the certificate message exchange (Section 6.2). Besides, certificates may also be revoked prior to the normal expiration date. To increase security the client MAY verify the state of the server's certificate via OCSP periodically. 11.3. Usage of NTP Pools The certification based authentication scheme described in Section 6 is not applicable to the concept of NTP pools. Therefore, NTS is not able to provide secure usage of NTP pools. 11.4. Denial-of-Service in Broadcast Mode TESLA authentication buffers packets for delayed authentication. This makes the protocol vulnerable to flooding attacks, causing the client to buffer excessive numbers of packets. To add stronger DoS protection to the protocol, client and server use the "Not Re-using Keys" scheme of TESLA as pointed out in section 3.7.2 of RFC 4082 [RFC4082]. In this scheme the server never uses a key for the MAC generation more than once. Therefore the client can discard any packet that contains a disclosed key it knows already, thus preventing memory flooding attacks. Note, an alternative approach to enhance TESLA's resistance against DoS attacks involves the addition of a group MAC to each packet. This requires the exchange of an additional shared key common to the whole group. This adds additional complexity to the protocol and hence is currently not considered in this document. 11.5. Delay Attack In a packet delay attack, an adversary with the ability to act as a MITM delays time synchronization packets between client and server asymmetrically [I-D.ietf-tictoc-security-requirements]. This prevents the client to measure the network delay, and hence its time offset to the server, accurately [Mizrahi]. The delay attack does Sibold, et al. Expires January 5, 2015 [Page 19] Internet-Draft NTS July 2014 not modifiy the content of the exchanged synchronization packets. Therefore cryptographic means are not feasible to mitigate this attack. However, serveral non-cryptographic precautions can be taken in order to detect this attack. o Usage of multiple time servers: this enables the client to detect the attack provided that the adversary is unable to delay the synchronizations packets between the majority of servers. This approach is commonly used in NTP to exclude incorrect time servers [RFC5905]. o Multiple communication paths: The client and server are utilizing different paths for packet exchange as described in the I-D [I-D.shpiner-multi-path-synchronization]. The client can detect the attack provided that the adversary is unable to manipulate the majority of the available paths [Shpiner]. Note, that this approach is not yet available, neither for NTP nor for PTP. o The introduction of a threshold value for the delay time of the synchronization packets. The client can discard a time server if the packet delay time of this time server is larger than the threshold value. o Usage of an encrypted connection: the client exchanges all packets with the time server over an encrypted connection (e.g. IPsec). This measure does not mitigate the delay attack but it makes it more difficult for the adversary to identify the time synchronization packets. 12. Acknowledgements The authors would like to thank Steven Bellovin, David Mills and Kurt Roeckx for discussions and comments on the design of NTS. Also, thanks to Harlan Stenn for his technical review and specific text contributions to this document. 13. References 13.1. Normative References [IEEE1588] IEEE Instrumentation and Measurement Society. TC-9 Sensor Technology, "IEEE standard for a precision clock synchronization protocol for networked measurement and control systems", 2008. Sibold, et al. Expires January 5, 2015 [Page 20] Internet-Draft NTS July 2014 [RFC2104] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed- Hashing for Message Authentication", RFC 2104, February 1997. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC3161] Adams, C., Cain, P., Pinkas, D., and R. Zuccherato, "Internet X.509 Public Key Infrastructure Time-Stamp Protocol (TSP)", RFC 3161, August 2001. [RFC4082] Perrig, A., Song, D., Canetti, R., Tygar, J., and B. Briscoe, "Timed Efficient Stream Loss-Tolerant Authentication (TESLA): Multicast Source Authentication Transform Introduction", RFC 4082, June 2005. [RFC5905] Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network Time Protocol Version 4: Protocol and Algorithms Specification", RFC 5905, June 2010. [RFC5906] Haberman, B. and D. Mills, "Network Time Protocol Version 4: Autokey Specification", RFC 5906, June 2010. [RFC6277] Santesson, S. and P. Hallam-Baker, "Online Certificate Status Protocol Algorithm Agility", RFC 6277, June 2011. 13.2. Informative References [I-D.ietf-tictoc-security-requirements] Mizrahi, T., "Security Requirements of Time Protocols in Packet Switched Networks", draft-ietf-tictoc-security- requirements-10 (work in progress), July 2014. [I-D.shpiner-multi-path-synchronization] Shpiner, A., Tse, R., Schelp, C., and T. Mizrahi, "Multi- Path Time Synchronization", draft-shpiner-multi-path- synchronization-03 (work in progress), February 2014. [Mizrahi] Mizrahi, T., "A game theoretic analysis of delay attacks against time synchronization protocols", in Proceedings of Precision Clock Synchronization for Measurement Control and Communication, ISPCS 2012, pp. 1-6, September 2012. [RFC4086] Eastlake, D., Schiller, J., and S. Crocker, "Randomness Requirements for Security", BCP 106, RFC 4086, June 2005. Sibold, et al. Expires January 5, 2015 [Page 21] Internet-Draft NTS July 2014 [Roettger] Roettger, S., "Analysis of the NTP Autokey Procedures", February 2012. [Shpiner] Shpiner, A., Revah, Y., and T. Mizrahi, "Multi-path Time Protocols", in Proceedings of Precision Clock Synchronization for Measurement Control and Communication, ISPCS 2013, pp. 1-6, September 2013. Appendix A. Flow Diagrams of Client Behaviour Sibold, et al. Expires January 5, 2015 [Page 22] Internet-Draft NTS July 2014 +---------------------+ |Association Messages | +----------+----------+ | v +---------------------+ |Certificate Messages | +----------+----------+ | +------------------------------>o | | | v | +---------------+ | |Cookie Messages| | +-------+-------+ | | | o<------------------------------+ | | | | v | | +-------------------+ | | |Time Sync. Messages| | | +---------+---------+ | | | | | v | | +-----+ | | |Check| | | +--+--+ | | | | | /------------------+------------------\ | | v v v | | .-----------. .-------------. .-------. | | ( MAC Failure ) ( Nonce Failure ) ( Success ) | | '-----+-----' '------+------' '---+---' | | | | | | | v v v | | +-------------+ +-------------+ +--------------+ | | |Discard Data | |Discard Data | |Sync. Process | | | +-------------+ +------+------+ +------+-------+ | | | | | | | | | v | +-----------+ +------------------>o-----------+ Figure 1: The client's behavior in NTS unicast mode. Sibold, et al. Expires January 5, 2015 [Page 23] Internet-Draft NTS July 2014 +-----------------------------+ |Broadcast Parameter Messages | +--------------+--------------+ | o<--------------------------+ | | v | +-----------------------------+ | |Broadcast Time Sync. Message | | +--------------+--------------+ | | | +-------------------------------------->o | | | | | v | | +-------------------+ | | |Key and Auth. Check| | | +---------+---------+ | | | | | /----------------*----------------\ | | v v | | .---------. .---------. | | ( Verified ) ( Falsified ) | | '----+----' '----+----' | | | | | | v v | | +-------------+ +-------+ | | |Store Message| |Discard| | | +------+------+ +---+---+ | | | | | | v +---------o | +---------------+ | | |Check Previous | | | +-------+-------+ | | | | | /--------*--------\ | | v v | | .---------. .---------. | | ( Verified ) ( Falsified ) | | '----+----' '----+----' | | | | | | v v | | +-------------+ +-----------------+ | | |Sync. Process| |Discard Previous | | | +------+------+ +--------+--------+ | | | | | +-----------+ +-----------------------------------+ Figure 2: The client's behaviour in NTS broadcast mode. Sibold, et al. Expires January 5, 2015 [Page 24] Internet-Draft NTS July 2014 Appendix B. Extension Fields In Section 6, some new extension fields for NTP packets are introduced. They are listed here again, for reference. +------------------------+---------------+ | name | used in | +------------------------+---------------+ | "association" | client_assoc | | | server_assoc | | | | | "certificate request" | client_cert | | | | | "certificate" | server_cert | | | | | "cookie request" | client_cook | | | | | "cookie transmit" | server_cook | | | | | "time request" | time_request | | | | | "time response" | time_response | | | | | "broadcast request" | client_bpar | | | | | "broadcast parameters" | server_bpar | | | | | "broadcast message" | server_broad | +------------------------+---------------+ Appendix C. TICTOC Security Requirements The following table compares the NTS specifications against the TICTOC security requirements [I-D.ietf-tictoc-security-requirements]. +---------+------------------------------------+-------------+------+ | Section | Requirement from I-D tictoc | Requirement | NTS | | | security-requirements-05 | level | | +---------+------------------------------------+-------------+------+ | 5.1.1 | Authentication of Servers | MUST | OK | +---------+------------------------------------+-------------+------+ | 5.1.1 | Authorization of Servers | MUST | OK | +---------+------------------------------------+-------------+------+ | 5.1.2 | Recursive Authentication of | MUST | OK | | | Servers (Stratum 1) | | | +---------+------------------------------------+-------------+------+ | 5.1.2 | Recursive Authorization of Servers | MUST | OK | | | (Stratum 1) | | | Sibold, et al. Expires January 5, 2015 [Page 25] Internet-Draft NTS July 2014 +---------+------------------------------------+-------------+------+ | 5.1.3 | Authentication and Authorization | MAY | - | | | of Slaves | | | +---------+------------------------------------+-------------+------+ | 5.2 | Integrity protection. | MUST | OK | +---------+------------------------------------+-------------+------+ | 5.4 | Protection against DoS attacks | SHOULD | OK | +---------+------------------------------------+-------------+------+ | 5.5 | Replay protection | MUST | OK | +---------+------------------------------------+-------------+------+ | 5.6 | Key freshness. | MUST | OK | +---------+------------------------------------+-------------+------+ | | Security association. | SHOULD | OK | +---------+------------------------------------+-------------+------+ | | Unicast and multicast | SHOULD | OK | | | associations. | | | +---------+------------------------------------+-------------+------+ | 5.7 | Performance: no degradation in | MUST | OK | | | quality of time transfer. | | | +---------+------------------------------------+-------------+------+ | | Performance: lightweight | SHOULD | OK | | | computation | | | +---------+------------------------------------+-------------+------+ | | Performance: storage, bandwidth | SHOULD | OK | +---------+------------------------------------+-------------+------+ | 5.7 | Confidentiality protection | MAY | NO | +---------+------------------------------------+-------------+------+ | 5.9 | Protection against Packet Delay | SHOULD | NA*) | | | and Interception Attacks | | | +---------+------------------------------------+-------------+------+ | 5.10 | Secure mode | MUST | - | +---------+------------------------------------+-------------+------+ | | Hybrid mode | SHOULD | - | +---------+------------------------------------+-------------+------+ *) See discussion in section Section 11.5. Comparison of NTS sepecification against TICTOC security requirements. Appendix D. Broadcast Mode For the broadcast mode, NTS adopts the TESLA protocol, which is based on a one-way key chain. This appendix provides details on the generation and usage of the one-way key chain collected and assembled from [RFC4082]. Note that NTS is using the "not re-using keys" scheme of TESLA as described in section 3.7.2. of [RFC4082]. Sibold, et al. Expires January 5, 2015 [Page 26] Internet-Draft NTS July 2014 D.1. Server Preparations Server setup: 1. The server determines a reasonable upper bound B on the network delay between itself and an arbitrary client, measured in milliseconds. 2. It determines the number n+1 of keys in the one-way key chain. This yields the number n of keys that are usable to authenticate broadcast packets. This number n is therefore also the number of time intervals during which the server can send authenticated broadcast messages before it has to calculate a new key chain. 3. It divides time into n uniform intervals I_1, I_2, ..., I_n. Each of these time intervals has length L, measured in milliseconds. In order to fulfill the requirement 3.7.2. of RFC 4082 the time interval L has to be smaller than the time interval between the broadcast messages. 4. The server generates a random key K_n. 5. Using a one-way function F, the server generates a one-way chain of n+1 keys K_0, K_1, ..., K_{n} according to K_i = F(K_{i+1}). 6. Using another one-way function F', it generates a sequence of n+1 MAC keys K'_0, K'_1, ..., K'_{n-1} according to K'_i = F'(K_i). 7. Each MAC key K'_i is assigned to the time interval I_i. 8. The server determines the key disclosure delay d, which is the number of intervals between using a key and disclosing it. Note that although security is still provided for all choices d>0, the choice still makes a difference: * If d is chosen too short, the client might discards packets because it fails to verify that the key used for their MAC has not been yet disclosed. * If d is chosen too long, the received packets have to be buffered for a unnecessarily long time before they can be verified by the client and subsequently be utilized for time synchronization. Sibold, et al. Expires January 5, 2015 [Page 27] Internet-Draft NTS July 2014 The server SHOULD calculate d according to d = ceil( 2*B / L) + 1, where ceil gives the smallest integer greater than or equal to its argument. < - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Generation of Keys F F F F K_0 <-------- K_1 <-------- ... <-------- K_{n-1} <-------- K_n | | | | | | | | | F' | F' | F' | F' | | | | v v v v K'_0 K'_1 ... K'_{n-1} K'_n [______________|____ ____|_________________|__________] I_1 ... I_{n-1} I_n Course of Time/Usage of Keys - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > A Schematic explanation on the TESLA protocol's one-way key chain D.2. Client Preparation A client needs the following information in order to participate in a TESLA broadcast. o One key K_i from the one-way key chain, which has to be authenticated as belonging to the server. Typically, this will be K_0. o The disclosure schedule of the keys. This consists of: * the length n of the one-way key chain, * the length L of the time intervals I_1, I_2, ..., I_n, * the starting time T_i of an interval I_i. Typically this is the starting time T_1 of the first interval; * the disclosure delay d. o The one-way function F used to recursively derive the keys in the one-way key chain, Sibold, et al. Expires January 5, 2015 [Page 28] Internet-Draft NTS July 2014 o The second one-way function F' used to derive the MAC keys K'_0, K'_1, ... , K'_n from the keys in the one-way chain. o An upper bound D_t on how far its own clock is "behind" that of the server. Note that if D_t is greater than (d - 1) * L, then some authentic packets might be discarded. If D_t is greater than d * L, then all authentic packets will be discarded. In the latter case, the client should not participate in the broadcast, since there will be no benefit in doing so. D.3. Sending Authenticated Broadcast Packets During each time interval I_i, the server sends one authenticated broadcast packet P_i. This packet consists of: o a message M_i, o the index i (in case a packet arrives late), o a MAC authenticating the message M_i, with K'_i used as key, o the key K_{i-d}, which is included for disclosure. D.4. Authentication of Received Packets When a client receives a packet P_i as described above, it first checks that it has not received a packet with associated index i before. This is done to avoid replay/flooding attacks. A packet that fails this test is discarded. Next, the client checks that, according to the disclosure schedule and with respect to the upper bound D_t determined above, the server cannot have disclosed the key K_i yet. Specifically, it needs to check that the server's clock cannot read a time that is in time interval I_{i+d} or later. Since it works under the assumption that the server's clock is not more than D_t "ahead" of the client's clock, the client can calculate an upper bound t_i for the server's clock at the time when P_i arrived by t_i = R + D_t, where R is the client's clock at the arrival of P_i. This implies that at the time of arrival of P_i, the server could have been in interval I_x at most, with x = floor((t_i - T_1) / L), Sibold, et al. Expires January 5, 2015 [Page 29] Internet-Draft NTS July 2014 where floor gives the greatest integer less than or equal to its argument. The client now needs to verify that x < i+d is valid (see also section 3.5 of [RFC4082]). If falsified, it is discarded. Next the client verifies that a newly disclosed key K_{i-d} belongs to the one-way key chain. To this end it verifies identity with some earlier disclosed key by recursively applies the one-way function F to K_{i-d} (see Clause 3.5 in RFC 4082, item 3). If a packet P_i passes all tests listed above, it is stored for later authentication. Also, if at this time there is a package with index i-d already buffered, then the client uses the disclosed key K_{i-d} to derive K'_{i-d} and uses that to check the MAC included in package P_{i-d}. On success, it regards M_{i-d} as authenticated. Appendix E. Random Number Generation At various points of the protocol, the generation of random numbers is required. The employed methods of generation need to be cryptographically secure. See [RFC4086] for guidelines concerning this topic. Authors' Addresses Dieter Sibold Physikalisch-Technische Bundesanstalt Bundesallee 100 Braunschweig D-38116 Germany Phone: +49-(0)531-592-8420 Fax: +49-531-592-698420 Email: dieter.sibold@ptb.de Stephen Roettger Email: stephen.roettger@googlemail.com Sibold, et al. Expires January 5, 2015 [Page 30] Internet-Draft NTS July 2014 Kristof Teichel Physikalisch-Technische Bundesanstalt Bundesallee 100 Braunschweig D-38116 Germany Phone: +49-(0)531-592-8421 Email: kristof.teichel@ptb.de Sibold, et al. Expires January 5, 2015 [Page 31]