MPLS WG Bilel Jamoussi, Editor Internet Draft Nortel Networks Corp. Expiration Date: February 2000 August 1999 Constraint-Based LSP Setup using LDP draft-ietf-mpls-cr-ldp-02.txt Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as _work in progress._ The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract Label Distribution Protocol (LDP) is defined in [1] for distribution of labels inside one MPLS domain. One of the most important services that may be offered using MPLS in general and LDP in particular is support for constraint-based routing of traffic across the routed network. Constraint-based routing offers the opportunity to extend the information used to setup paths beyond what is available for the routing protocol. For instance, an LSP can be setup based on explicit route constraints, QoS constraints, and other constraints. Constraint-based routing (CR) is a mechanism used to meet Traffic Engineering requirements that have been proposed by [2], [3] and [4]. These requirements may be met by extending LDP for support of constraint-based routed label switched paths (CRLSPs). Other uses exist for CRLSPs as well ([5], [6] and [7]). This draft specifies mechanisms and TLVs for support of CRLSPs using LDP. The Explicit Route object and procedures are extracted from [8]. Table of Contents Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 1 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 1. Introduction....................................................3 2. Constraint-based Routing Overview...............................3 2.1 Strict and Loose Explicit Routes...............................3 2.2 Traffic Characteristics........................................4 2.3 Pre-emption....................................................4 2.4 Route Pinning..................................................5 2.5 Resource Class.................................................5 3. Solution Overview...............................................5 3.1 Required Messages and TLVs.....................................6 3.2 Label Request Message..........................................7 3.3 Label Mapping Message..........................................7 3.4 Notification Message...........................................8 3.5 Release , Withdraw, and Abort Messages.........................9 4. Protocol Specification..........................................9 4.1 Explicit Route TLV (ER-TLV)....................................9 4.2 Explicit Route Hop TLV (ER-Hop TLV)...........................10 4.3 Traffic Parameters TLV........................................11 4.3.1 Semantics...................................................13 4.3.1.1 Frequency.................................................13 4.3.1.2 Peak Rate.................................................13 4.3.1.3 Committed Rate............................................13 4.3.1.4 Excess Burst Size.........................................14 4.3.1.5 Peak Rate Token Bucket....................................14 4.3.1.6 Committed Data Rate Token Bucket..........................14 4.3.1.7 Weight....................................................15 4.3.2 Procedures..................................................15 4.3.2.1 Label Request Message.....................................15 4.3.2.2 Label Mapping Message.....................................16 4.3.2.3 Notification Message......................................16 4.4 Preemption TLV................................................16 4.5 LSPID TLV.....................................................17 4.6 Resource Class (Color) TLV....................................18 4.7 ER-Hop semantics..............................................19 4.7.1. ER-Hop 1: The IPv4 prefix..................................19 4.7.2. ER-Hop 2: The IPv6 address.................................19 4.7.3. ER-Hop 3: The autonomous system number....................20 4.7.4. ER-Hop 4: LSPID............................................20 4.8. Processing of the Explicit Route TLV.........................22 4.8.1. Selection of the next hop..................................22 4.8.2. Adding ER-Hops to the explicit route TLV...................23 4.9 Route Pinning TLV.............................................23 4.10 CRLSP FEC Element............................................24 4.11 Error subcodes...............................................24 5. Security.......................................................25 6. Acknowledgments................................................25 7. Intellectual Property Consideration............................25 8. References.....................................................25 9. Author's Addresses.............................................26 Appendix A: CRLSP Establishment Examples..........................29 A.1 Strict Explicit Route Example.................................29 A.2. Node Groups and Specific Nodes Example.......................30 Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 2 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Appendix B. QoS Service Examples..................................33 B.1 Service Examples..............................................33 B.2. Establishing CR-LSP Supporting Real-Time Applications........34 B.3. Establishing CR-LSP Supporting Delay Insensitive Applications35 1. Introduction The need for constraint-based routing (CR) in MPLS has been explored elsewhere [3], [2], and [4]. Explicit routing is a subset of the more general constraint-based routing function. At the MPLS WG meeting held during the Washington IETF (December 1997) there was consensus that LDP should support explicit routing of LSPs with provision for indication of associated (forwarding) priority. In the Chicago meeting (August 1998), a decision was made that support for explicit path setup in LDP will be moved to a separate document. This document provides that support and it has been accepted as a working document in the Orlando meeting (December 1998). This specification proposes an end-to-end setup mechanism of a constraint-based routed LSP (CRLSP) initiated by the ingress LSR. We also specify mechanisms to provide means for reservation of resources using LDP. This document introduce TLVs and procedures that provide support for: - Strict and Loose Explicit Routing - Specification of Traffic Parameters - Route Pinning - CRLSP Pre-emption though setup/holding priorities - Handling Failures - LSPID - Resource Class Section 2 introduces the various constraints defined in this specification. Section 3 outlines the CR-LDP solution. Section 4 defines the TLVs and procedures used to setup constraint-based routed label switched paths. Appendix A provides several examples of CR-LSP path setup. Appendix B provides Service Definition Examples. 2. Constraint-based Routing Overview Constraint-based routing is a mechanism that supports the Traffic Engineering requirements defined in [4]. Explicit Routing is a subset of the more general constraint-based routing where the constraint is the explicit route (ER). Other constraints are defined to provide a network operator with control over the path taken by an LSP. This section is an overview of the various constraints supported by this specification. 2.1 Strict and Loose Explicit Routes Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 3 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Like any other LSP an CRLSP is a path through an MPLS network. The difference is that while other paths are setup solely based on information in routing tables or from a management system, the constraint-based route is calculated at one point at the edge of network based on criteria, including but not limited to routing information. The intention is that this functionality shall give desired special characteristics to the LSP in order to better support the traffic sent over the LSP. The reason for setting up CRLSPs, might be that one wants to assign certain bandwidth or other Service Class characteristics to the LSP, or that one wants to make sure that alternative routes use physically separate paths through the network. An explicit route is represented in a Label Request Message as a list of nodes or groups of nodes along the constraint-based route. When the CRLSP is established, all or a subset of the nodes in a group may be traversed by the LSP. Certain operations to be performed along the path can also be encoded in the constraint-based route. The capability to specify, in addition to specified nodes, groups of nodes, of which a subset will be traversed by the CRLSP, allows the system a significant amount of local flexibility in fulfilling a request for a constraint-based route. This allows the generator of the constraint-based route to have some degree of imperfect information about the details of the path. The constraint-based route is encoded as a series of ER-Hops contained in a constraint-based route TLV. Each ER-Hop may identify a group of nodes in the constraint-based route. A constraint-based route is then a path including all of the identified groups of nodes. To simplify the discussion, we call each group of nodes an abstract node. Thus, we can also say that a constraint-based route is a path including all of the abstract nodes, with the specified operations occurring along that path. 2.2 Traffic Characteristics The traffic characteristics of a path are described in the Traffic Parameters TLV in terms of a peak rate, committed rate, and service granularity. The peak and committed rates describe the bandwidth constraints of a path while the service granularity can be used to specify a constraint on the delay variation that the CRLDP MPLS domain may introduce to a path's traffic. 2.3 Pre-emption CR-LDP signals the resources required by a path on each hop of the route. If a route with sufficient resources can not be found, existing paths may be rerouted to reallocate resources to the new Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 4 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 path. This is the process of path pre-emption. Setup and holding priorities are used to rank existing paths (holding priority) and the new path (setup priority) to determine if the new path can pre- empt an existing path. The setupPriority of a new CRLSP and the holdingPriority attributes of the existing CRLSP are used to specify priorities. Signaling a higher holding priority express that the path, once it has been established, should have a lower chance of being pre-empted. Signaling a higher setup priority expresses the expectation that, in the case that resource are unavailable, the path is more likely to pre-empt other paths. The exact rules determining bumping are an aspect of network policy. The allocation of setup and holding priority values to paths is an aspect of network policy. The setup and holding priority values range from zero (0) to seven (7). The value zero (0) is the priority assigned to the most important path. It is referred to as the highest priority. Seven (7) is the priority for the least important path. The use of default priority values is an aspect of network policy. The setupPriority of a CRLSP should not be higher (numerically less) than its holdingPriority since it might bump an LSP and be bumped by next _equivalent_ request. 2.4 Route Pinning Route pinning is applicable to segments of an LSP that are loosely routed - i.e. those segments which are specified with a next hop with the `L' bit set or where the next hop is an _abstract node_. A CRLSP may be setup using route pinning if it is undesirable to change the path used by an LSP because a better next hop becomes available at some LSR along the loosely routed portion of the LSP. 2.5 Resource Class The network operator may classify network resources in various ways. These classes are also known as _colors_ or _administrative groups_. When an CR-LSP is being established, it's necessary to indicate which resource classes the CR-LSP can draw from. 3. Solution Overview CRLSP over LDP Specification is designed with the following goals: 1. Meet the requirements outlined in [4] for performing traffic engineering and provide a solid foundation for performing more general constraint-based routing. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 5 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 2. Build on already specified functionality that meets the requirements whenever possible. Hence, this specification is based on [1] and the Explicit Route object and procedures defined in [8]. 3. Keep the solution simple. In this document, support for unidirectional point-to-point CRLSPs is specified. Support for point-to-multipoint, multipoint-to-point, is for further study (FFS). Support for constraint-based routed LSPs in this specification depends on the following minimal LDP behaviors as specified in [1]: - Basic and/or Extended Discovery Mechanisms. - Use the Label Request Message defined in [1] in downstream on demand label advertisement mode with ordered control. - Use the Label Mapping Message defined in [1] in downstream on demand mode with ordered control. - Use the Notification Message defined in [1]. - Use the Withdraw and Release Messages defined in [1]. - Use the Loop Detection (in the case of loosely routed segments of a CRLSP) mechanisms defined in [1]. In addition, the following functionality is added to what's defined in [1]: - The Label Request Message used to setup a CRLSP includes one or more CR-TLVs defined in Section 4. For instance, the Label Request Message may include the ER-TLV. - An LSR implicitly infers ordered control from the existence of one or more CR-TLVs in the Label Request Message. This means that the LSR can still be configured for independent control for LSPs established as a result of dynamic routing. However, when a Label Request Message includes one or more of the CR- TLVs, then ordered control is used to setup the CRLSP. Note that this is also true for the loosely routed parts of a CRLSP. - New status codes are defined to handle error notification for failure of established paths specified in the CR-TLV. Optional TLVs are not required in the CR-LDP messages for the messages to be compliant with the protocol. Optional parameters CAN be required for a particular operation to work (or work correctly), however. Examples of CRLSP establishment are given in Appendix A to illustrate how the mechanisms described in this draft work. 3.1 Required Messages and TLVs Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 6 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Any Messages, TLVs, and procedures not defined explicitly in this document are defined in the LDP Specification [1]. The state transitions, which relate to CR-LDP messages, can be found in [9]. The following subsections are meant as a cross-reference to the [1] document and indication of additional functionality beyond what's defined in [1] where necessary. 3.2 Label Request Message The Label Request Message is as defined in 3.5.8 of [1] with the following modifications (required only if any of the CR-TLVs is included in the Label Request Message): - Only a single FEC-TLV may be included in the Label Request Message. The CR-LSP FEC TLV should be used. - The Optional Parameters TLV includes the definition of any of the Constraint-based TLVs specified in Section 4. - The Procedures to handle the Label Request Message are augmented by the procedures for processing of the CR-TLVs as defined in Section 4. The encoding for the CR-LDP Label Request Message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0| Label Request (0x0401) | Message Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | FEC TLV | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message ID TLV (mandatory) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LSPID TLV (CR-LDP, mandatory) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ER-TLV (CR-LDP, optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Traffic TLV (CR-LDP, optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Pinning TLV (CR-LDP, optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Resource Class TLV (CR-LDP, optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Pre-emption TLV (CR-LDP, optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 3.3 Label Mapping Message Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 7 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 The Label Mapping Message is as defined in 3.5.7 of [1] with the following modifications: - Only a single Label-TLV may be included in the Label Mapping Message. - The Label Mapping Message Procedures are limited to downstream on demand ordered control mode. A Mapping message is transmitted by a downstream LSR to an upstream LSR under one of the following conditions: 1. The LSR is the egress end of the CRLSP and an upstream mapping has been requested. 2. The LSR received a mapping from its downstream next hop LSR for an CRLSP for which an upstream request is still pending. The encoding for the CR-LDP Label Mapping Message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0| Label Mapping (0x0400) | Message Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | FEC TLV | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label TLV | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Label Request Message ID TLV | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LSPID TLV (CR-LDP, optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Traffic TLV (CR-LDP, optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 3.4 Notification Message The Notification Message is as defined in Section 3.5.1 of [1] and the Status TLV encoding is as defined in Section 3.4.7 of [1]. Establishment of an Explicitly Routed LSP may fail for a variety of reasons. All such failures are considered advisory conditions and they are signaled by the Notification Message. Notification Messages carry Status TLVs to specify events being signaled. New status codes are defined in Section 4.11 to signal error notifications associated with the establishment of a CRLSP and the processing of the CR-TLV. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 8 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 The Notification Message must carry the LSPID TLV of the corresponding CRLSP. Notification Messages MUST be forwarded toward the LSR originating the Label Request at each hop and at any time that procedures in this specification - or in [1] - specify sending of a Notification Message in response to a Label Request Message. The encoding of the notification message is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0| Notification (0x0001) | Message Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Message ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Status (TLV) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Optional Parameters | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 3.5 Release , Withdraw, and Abort Messages The Label Release , Label Withdraw, and Label Abort Request Messages are used as specified in [1]. These messages may also carry the LSPID TLV. 4. Protocol Specification The Label Request Messages defined in [1] optionally carries one or more of the optional Constraint-based Routing TLVs (CR-TLVs) defined in this section. If needed, other constraints can be supported later through the definition of new TLVs. In this specification, the following TLVs are defined: - Explicit Route TLV - Explicit Route Hop TLV - Traffic Parameters TLV - Preemption TLV - LSPID TLV - Route Pinning TLV - Resource Class TLV - CRLSP FEC TLV 4.1 Explicit Route TLV (ER-TLV) The ER-TLV is an object that specifies the path to be taken by the LSP being established. It is composed of one or more Explicit Route Hop TLVs (ER-Hop TLVs) defined in Section 4.2. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 9 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| ER-TLV (0x0800) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ER-Hop TLV 1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ER-Hop TLV 2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ ............ ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ER-Hop TLV n | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type A two-byte field carrying the value of the ER-TLV type whichis 0x800. Length Specifies the length of the value field in bytes. ER-Hop TLVs One or more ER-Hop TLVs defined in Section 4.2. 4.2 Explicit Route Hop TLV (ER-Hop TLV) The contents of an ER-TLV are a series of variable length ER-Hop TLVs. A node receiving a label request message including an ER-Hop type that is not supported should not progress the label request message to the downstream LSR and should send back a _No Route_ Notification Message. Each ER-Hop TLV has the form: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| ER-Hop-Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |L| Content // | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ER-Hop Type A fourteen-bit field indicating the type of contents of the ER- Hop. Currently defined values are: Value Type ----- ------------------------ 0x801 IPv4 prefix 0x802 IPv6 prefix Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 10 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 0x803 Autonomous system number 0x804 LSPID Length Specifies the length of the value field in bytes. L bit The L bit is an attribute of the ER-Hop. The L bit is set if the ER-Hop ER-Hop represents a loose hop in the explicit route. If the bit is not set, the ER-Hop represents a strict hop in the explicit route. The L bit in the ER-Hop is a one-bit attribute. If the L bit is set, then the value of the attribute is _loose._ Otherwise, the value of the attribute is _strict._ For brevity, we say that if the value of the ER-Hop attribute is loose then it is a _loose ER-Hop._ Otherwise, it's a _strict ER-Hop._ Further, we say that the abstract node of a strict or loose ER-Hop is a strict or a loose node, respectively. Loose and strict nodes are always interpreted relative to their prior abstract nodes. The path between a strict node and its prior node MUST include only network nodes from the strict node and its prior abstract node. The path between a loose node and its prior node MAY include other network nodes, which are not part of the strict node or its prior abstract node. Contents A variable length field containing the node or abstract node that is the consecutive nodes that make up the explicit routed LSP. 4.3 Traffic Parameters TLV The following sections describe the CRLSP Traffic Parameters. The required characteristics of a CRLSP are expressed by the Traffic Parameter values. A Traffic Parameters TLV, is used to signal the Traffic Parameter values. The Traffic Parameters are defined in the subsequent sections. The Traffic Parameters TLV contains a Flags field, a Frequency, a Weight, and the five Traffic Parameters PDR, PBS, CDR, CBS, EBS. The Traffic Parameters TLV is shown below: Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 11 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| Traf. Param. TLV (0x0810)| Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Flags | Frequency | Reserved | Weight | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Peak Data Rate (PDR) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Peak Burst Size (PBS) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Committed Data Rate (CDR) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Committed Burst Size (CBS) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Excess Burst Size (EBS) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type A fourteen-bit field carrying the value of the ER-TLV type which is 0x810. Length Specifies the length of the value field in bytes. Flags The Flags field is shown below: +--+--+--+--+--+--+--+--+ | Res |F6|F5|F4|F3|F2|F1| +--+--+--+--+--+--+--+--+ Res - These bits are reserved. Zero on transmission. Ignored on receipt. F1 - Corresponds to the PDR. F2 - Corresponds to the PBS. F3 - Corresponds to the CDR. F4 - Corresponds to the CBS. F5 - Corresponds to the EBS. F6 - Corresponds to the Weight. Each flag Fi is a Negotiable Flag corresponding to a Traffic Parameter. The Negotiable Flag value zero denotes NotNegotiable and value one denotes Negotiable. Frequency The Frequency field is coded as an 8 bit unsigned integer with the following code points defined: 0- Unspecified 1- Frequent Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 12 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 2- VeryFrequest 3-255 - Reserved Reserved Zero on transmission. Ignored on receipt. Weight An 8 bit unsigned integer indicating the weight of the CRLSP. Valid weight values are from 1 to 255. The value 0 means that weight is not applicable for the CRLSP. Traffic Parameters Each Traffic Parameter is encoded as a 32-bit IEEE single- precision floating-point number. A value of positive infinity is represented as an IEEE single-precision floating-point number with an exponent of all ones (255) and a sign and mantissa of all zeros. The values PDR and CDR are in units of bytes per second. The values PBS, CBS and EBS are in units of bytes. The value of PDR MUST be greater than or equal to the value of CDR in a correctly encoded Traffic Parameters TLV. 4.3.1 Semantics 4.3.1.1 Frequency The Frequency specifies at what granularity the CDR allocated to the CRLSP is made available. The value VeryFrequently means that the available rate should average at least the CDR when measured over any time interval equal to or longer than the shortest packet time at the CDR. The value Frequently means that the available rate should average at least the CDR when measured over any time interval equal to or longer than a small number of shortest packet times at the CDR. The value Unspecified means that the CDR MAY be provided at any granularity. 4.3.1.2 Peak Rate The Peak Rate defines the maximum rate at which traffic SHOULD be sent to the CRLSP. The Peak Rate is useful for the purpose of resource allocation. If resource allocation within the MPLS domain depends on the Peak Rate value then it should be enforced at the ingress to the MPLS domain. The Peak Rate is defined in terms of the two Traffic Parameters PDR and PBS, see section 4.3.1.5 below. 4.3.1.3 Committed Rate The Committed Rate defines the rate that the MPLS domain commits to be available to the CRLSP. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 13 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 The Committed Rate is defined in terms of the two Traffic Parameters CDR and CBS, see section 4.3.1.6 below. 4.3.1.4 Excess Burst Size The Excess Burst Size may be used at the edge of an MPLS domain for the purpose of traffic conditioning. The EBS MAY be used to measure the extent by which the traffic sent on a CRLSP exceeds the committed rate. The possible traffic conditioning actions, such as passing, marking or dropping, are specific to the MPLS domain. The Excess Burst Size is defined together with the Committed Rate, see section 4.3.1.6 below. 4.3.1.5 Peak Rate Token Bucket The Peak Rate of a CRLSP is specified in terms of a token bucket P with token rate PDR and maximum token bucket size PBS. The token bucket P is initially (at time 0) full, i.e., the token count Tp(0) = PBS. Thereafter, the token count Tp, if less than PBS, is incremented by one PDR times per second. When a packet of size B bytes arrives at time t, the following happens: - If Tp(t)-B >= 0, the packet is not in excess of the peak rate and Tp is decremented by B down to the minimum value of 0, else - the packet is in excess of the peak rate and Tp is not decremented. Note that according to the above definition, a positive infinite value of either PDR or PBS implies that arriving packets are ever in excess of the peak rate. The actual implementation of a LSR doesn't need to be modeled according to the above formal token bucket specification. 4.3.1.6 Committed Data Rate Token Bucket The committed rate of a CRLSP is specified in terms of a token bucket C with rate CDR. The extent by which the offered rate exceeds the committed rate MAY be measured in terms of another token bucket E, which also operates at rate CDR. The maximum size of the token bucket C is CBS and the maximum size of the token bucket E is EBS. The token buckets C and E are initially (at time 0) full, i.e., the token count Tc(0) = CBS and the token count Te(0) = EBS. Thereafter, the token counts Tc and Te are updated CDR times per second as follows: Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 14 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 - If Tc is less than CBS, Tc is incremented by one, else - if Te is less then EBS, Te is incremented by one, else - neither Tc nor Te is incremented. When a packet of size B bytes arrives at time t, the following happens: - If Tc(t)-B >= 0, the packet is not in excess of the Committed Rate and Tc is decremented by B down to the minimum value of 0, else - if Te(t)-B >= 0, the packet is in excess of the Committed rate but is not in excess of the EBS and Te is decremented by B down to the minimum value of 0, else - the packet is in excess of both the Committed Rate and the EBS and neither Tc nor Tc is decremented. Note that according to the above specification, a CDR value of positive infinity implies that arriving packets are never in excess of either the Committed Rate or EBS. A positive infinite value of either CBS or EBS implies that the respective limit cannot be exceeded. The actual implementation of a LSR doesn't need to be modeled according to the above formal specification. 4.3.1.7 Weight The weight determines the CRLSP's relative share of the possible excess bandwidth above its committed rate. The definition of _relative share_ is MPLS domain specific. 4.3.2 Procedures 4.3.2.1 Label Request Message If an LSR receives an incorrectly encoded Traffic Parameters TLV in which the value of PDR is less than the value of CDR then it MUST send a Notification Message including the Status code Traffic Parameters Unavailable to the upstream LSR from which it received the erroneous message. If a Traffic Parameter is indicated as Negotiable in the Label Request Message by the corresponding Negotiable Flag then an LSR MAY replace the Traffic Parameter value with a smaller value. If the Weight is indicated as Negotiable in the Label Request Message by the corresponding Negotiable Flag then an LSR may adjust replace the Weight value with a lower value (down to 0). Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 15 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 If, after possible Traffic Parameter negotiation, an LSR can support the CRLSP Traffic Parameters then the LSR MUST reserve the corresponding resources for the CRLSP. If, after possible Traffic Parameter negotiation, an LSR cannot support the CRLSP Traffic Parameters then the LSR MUST send a notification message that contains the Resource Unavailable status code. 4.3.2.2 Label Mapping Message If an LSR receives an incorrectly encoded Traffic Parameters TLV in which the value of PDR is less than the value of CDR then it MUST send a Label Release message containing the Status code Traffic Parameters Unavailable to the LSR from which it received the erroneous message. If the negotiation flag was set in the label request message, the egress LSR MUST include the (possibly negotiated) Traffic Parameters and Weight in the Label Mapping message. The Traffic Parameters and the Weight in a Label Mapping message MUST be forwarded unchanged. An LSR SHOULD adjust the resources that it reserved for a CRLSP when it receives a Label Mapping Message if the Traffic Parameters differ from those in the corresponding Label Request Message. 4.3.2.3 Notification Message If an LSR receives a Notification Message for a CRLSP, it SHOULD release any resources that it possibly had reserved for the CRLSP. In addition, on receiving a Notification Message from a Downstream LSR that is associated with a Label Request from an upstream LSR, the local LSR MUST propagate the Notification message using the procedures in [1]. 4.4 Preemption TLV The defualt value of the setup and holding priorities should be in the middle of the range (e.g., 4) so that this feature can be turned on gradually in an operational network by increasing or decerasing the priority starting at the middle of the range. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| Preemption-TLV (0x0820) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | SetPrio | HoldPrio | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 16 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Type A fourteen-bit field carrying the value of the Preemption-TLV type which is 0x810. Length Specifies the length of the value field in bytes. Reserved Zero on transmission. Ignored on receipt. SetPrio A SetupPriority of value zero (0) is the priority assigned to the most important path. It is referred to as the highest priority. Seven (7) is the priority for the least important path. The higher the setup priority, the more paths CR-LDP can bump to set up the path. The default value should be 4. HoldPrio A HoldingPriority of value zero (0) is the priority assigned to the most important path. It is referred to as the highest priority. Seven (7) is the priority for the least important path. The default value should be 4. The higher the holding priority, the less likely it is for CR- LDP to reallocate its bandwidth to a new path. 4.5 LSPID TLV LSPID is a unique identifier of a CRLSP within an MPLS network. The LSPID is composed of the ingress LSR Router ID and a Locally unique CRLSP ID to that LSR. The LSPID is useful in network management, in CR-LSP repair, and in using an already established CR-LSP as a hop in an ER-TLV. An action indicator flag_ is carried in the LSPID TLV. This _action indicator flag_ indicates explicitly the action that should be taken if the LSP already exists on the LSR receiving the message. The procedure for the code point _modify_ is defined in section 2.1. of [10]. The procedures for other flags are FFS. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| LSPID-TLV (0x0821) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved |ActFlg | Local CRLSP ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Ingress LSR Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 17 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Type A fourteen-bit field carrying the value of the LSPID-TLV type which is 0x821. Length Specifies the length of the value field in bytes. ActFlg Action Indicator Flag: A 4-bit field that indicates explicitly the action that should be taken if the LSP already exists on the LSR receiving the message. A set of indicator code points is proposed as follows: 0001: modify Reserved Zero on transmission. Ignored on receipt. Local CRLSP ID The Local LSP ID is an identifier of the CRLSP locally unique within the Ingress LSR originating the CRLDP. Ingress LSR Router ID "An LSR may use any of its own IPv4 in this field" 4.6 Resource Class (Color) TLV The Resource Class as defined in [4] is used to specify which links are acceptable by this CRLSP. This information allows for the network's topology to be pruned. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| ResCls-TLV (0x0822) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | RsCls | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type A fourteen-bit field carrying the value of the ResCls-TLV type which is 0x822. Length Specifies the length of the value field in bytes. RsCls The Resource Class bit mask indicating which of the 32 _administrative groups_ or _colors_ of links the CRLSP can traverse. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 18 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 4.7 ER-Hop semantics 4.7.1. ER-Hop 1: The IPv4 prefix The abstract node represented by this ER-Hop is the set of nodes, which have an IP address, which lies within this prefix. Note that a prefix length of 32 indicates a single IPv4 node. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| 0x801 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |L| Reserved | PreLen | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPv4 Address (4 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type IPv4 Address 0x801 Length Specifies the length of the value field in bytes. L Bit Set to indicate Loose hop. Cleared to indicate a strict hop. Reserved Zero on transmission. Ignored on receipt. PreLen Prefix Length 1-32 IP Address A four-byte field indicating the IP Address. 4.7.2. ER-Hop 2: The IPv6 address 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| 0x802 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |L| Reserved | PreLen | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPV6 address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPV6 address (continued) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | IPV6 address (continued) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 19 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 | IPV6 address (continued) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type 0x802 IPv6 address Length Specifies the length of the value field in bytes. L Bit Set to indicate Loose hop. Cleared to indicate a strict hop. Reserved Zero on transmission. Ignored on receipt. PreLen Prefix Length 1-128 IPv6 address A 128-bit unicast host address. 4.7.3. ER-Hop 3: The autonomous system number The abstract node represented by this ER-Hop is the set of nodes belonging to the autonomous system. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| 0x803 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |L| Reserved | AS Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type AS Number 0x803 Length Specifies the length of the value field in bytes. L Bit Set to indicate Loose hop. Cleared to indicate a strict hop. Reserved Zero on transmission. Ignored on receipt. AS Number Autonomous System number 4.7.4. ER-Hop 4: LSPID Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 20 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 The LSPID is used to identify the tunnel ingress point as the next hop in the ER. This ER-Hop allows for stacking new CR-LSPs within an already established CR-LSP. It also allows for splicing the CR-LSP being established with an existing CR-LSP. If an LSPID Hop is the last ER-Hop in an ER-TLV, than the LSR may splice the CR-LSP of the incoming Label Request to the CR-LSP that currently exists with this LSPID. This is useful, for example, at the point at which a Label Request used for local repair arrives at the next ER-Hop after the loosely specified CR-LSP segment. Use of the LSPID Hop in this scenario eliminates the need for ER-Hops to keep the entire remaining ER-TLV at each LSR that is at either (upstream or downstream) end of a loosely specified CR-LSP segment as part of its state information. This is due to the fact that the upstream LSR needs only to keep the next ER-Hop and the LSPID and the downstream LSR needs only to keep the LSPID in order for each end to be able to recognize that the same LSP is being identified. If the LSPID Hop is not the last hop in an ER-TLV, the LSR must forward the remaining ER-TLV in a Label Request message, using the CR-LSP specified by the LSPID, to the LSR that is the CR-LSP's egress. That LSR will continue processing of the CR-LSP Label Request Message. The result is a tunneled, or stacked, CR-LSP. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| 0x804 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |L| Reserved | Local LSPID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Ingress LSR Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type LSPID 0x804 Length Specifies the length of the value field in bytes. L Bit Set to indicate Loose hop. Cleared to indicate a strict hop. Reserved Zero on transmission. Ignored on receipt. Local LSPID A 2 byte field indicating the LSPID which is unique with reference to its Ingress LSR. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 21 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Ingress LSR Router ID "An LSR may use any of its own IPv4 addresses in this field" 4.8. Processing of the Explicit Route TLV 4.8.1. Selection of the next hop A Label Request Message containing a explicit route TLV must determine the next hop for this path. Selection of this next hop may involve a selection from a set of possible alternatives. The mechanism for making a selection from this set is implementation dependent and is outside of the scope of this specification. Selection of particular paths is also outside of the scope of this specification, but it is assumed that each node will make a best effort attempt to determine a loop-free path. Note that such best efforts may be overridden by local policy. To determine the next hop for the path, a node performs the following steps: 1. The node receiving the Label Request Message must first evaluate the first ER-Hop. If the L bit is not set in the first ER-Hop and if the node is not part of the abstract node described by the first ER-Hop, it has received the message in error, and should return a _Bad initial ER-Hop_ error. If the L bit is set and the local node is not part of the abstract node described by the first ER-Hop, the node selects a next hop that is along the path to the abstract node described by the first ER-Hop. If there is no first ER-Hop, the message is also in error and the system should return a _Bad Explicit Routing TLV_ error. 2. If there is no second ER-Hop, this indicates the end of the explicit route. The explicit route TLV should be removed from the Label Request Message. This node may or may not be the end of the LSP. Processing continues with section 4.8.2, where a new explicit route TLV may be added to the Label Request Message. 3. If the node is also a part of the abstract node described by the second ER-Hop, then the node deletes the first ER-Hop and continues processing with step 2, above. Note that this makes the second ER-Hop into the first ER-Hop of the next iteration. 4. The node determines if it is topologically adjacent to the abstract node described by the second ER-Hop. If so, the node selects a particular next hop which is a member of the abstract node. The node then deletes the first ER-Hop and continues processing with section 4.8.2. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 22 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 5. Next, the node selects a next hop within the abstract node of the first ER-Hop that is along the path to the abstract node of the second ER-Hop. If no such path exists then there are two cases: 5.a If the second ER-Hop is a strict ER-Hop, then there is an error and the node should return a _Bad strict node_ error. 5.b Otherwise, if the second ER-Hop is a loose ER-Hop, then the node selects any next hop that is along the path to the next abstract node. If no path exists within the MPLS domain, then there is an error, and the node should return a _Bad loose node_ error. 6. Finally, the node replaces the first ER-Hop with any ER-Hop that denotes an abstract node containing the next hop. This is necessary so that when the explicit route is received by the next hop, it will be accepted. 7. Progress the Label Request Message to the next hop. 4.8.2. Adding ER-Hops to the explicit route TLV After selecting a next hop, the node may alter the explicit route in the following ways. If, as part of executing the algorithm in section 4.8.1, the explicit route TLV is removed, the node may add a new explicit route TLV. Otherwise, if the node is a member of the abstract node for the first ER-Hop, then a series of ER-Hops may be inserted before the first ER-Hop or may replace the first ER-Hop. Each ER-Hop in this series must denote an abstract node that is a subset of the current abstract node. Alternately, if the first ER-Hop is a loose ER-Hop, an arbitrary series of ER-Hops may be inserted prior to the first ER-Hop. 4.9 Route Pinning TLV 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| 0x823 | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |P| Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Type Pinning-TLV type 0x823 Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 23 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Length Specifies the length of the value field in bytes. P Bit The P bit is set to 1 to indicate that route pinning is requested. The P bit is set to 0 to indicate that route pinning is not requested Reserved Zero on transmission. Ignored on receipt. 4.10 CRLSP FEC Element A new FEC element is introduced in this specification to support CR- LSPs. This new FEC element does not preclude the use of other FECs elements (Type=0x01, 0x02, 0x03) defined in the LDP spec in CR-LDP messages. The CRLDP FEC Element is an opaque FEC to be used only in Messages of CR-LSPs. FEC Element Type Value Type name CRLSP 0x04 No value; i.e., 0 value octets; The CR-LSP FEC TLV encoding is as follows: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0|0| FEC(0x0100) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CR-LSP (4) | +-+-+-+-+-+-+-+-+ Type FEC TLV type 0x0100 Length Specifies the length of the value field in bytes. CR-LSP FEC Element Type 0x04 4.11 Error subcodes In the processing described above, certain errors need to be reported as part of the Notification Message. This section defines the status codes for the errors described in this specification. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 24 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Status Code Type -------------------------------------- ---------- Bad Explicit Routing TLV Error 0x44000001 Bad Strict Node Error 0x44000002 Bad Loose Node Error 0x44000003 Bad Initial ER-Hop Error 0x44000004 Resource Unavailable 0x44000005 Traffic Parameters Unavailable 0x44000006 Setup abort (Label Request Aborted in [1]) 0x04000015 Modify request not supported 0x44000008 5. Security Pre-emption has to be controlled by the MPLS domain. Resource reservation requires the LSRs to have an LSP admission control function. Traffic Engineered LSPs can bypass normal routing. 6. Acknowledgments The messages used to signal the CRLSP setup are based on the work done by the [1] team. The Explicit Route object and procedures used in this specification are based on [8]. The authors would also like to acknowledge the careful review and comments of Ken Hayward, Greg Wright, Geetha Brown, Brian Williams, Paul Beaubien, Matthew Yuen, Liam Casey, and Ankur Anand. 7. Intellectual Property Consideration Nortel Networks may seek patent or other intellectual property protection for some or all of the technologies disclosed in this document. If any standards arising from this document are or become protected by one or more patents assigned to Nortel Networks, Nortel Networks is prepared to make a license available to any qualified applicant upon reasonable and non-discriminatory terms and conditions. Any such licenses will be subject to negotiations outside of the IETF. 8. References 1 Andersson et al, "Label Distribution Protocol Specification" work in progress (draft-ietf-mpls-ldp-05), June 1999. 2 Callon et al, "Framework for Multiprotocol Label Switching", work in progress (draft-ietf-mpls-framework-04), July 1999. 3 Rosen et al, "Multiprotocol Label Switching Architecture", work in progress (draft-ietf-mpls-arch-04), April 1999. Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 25 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 4 Awduche et al, "Requirements for Traffic Engineering Over MPLS", work in progress (draft-ietf-mpls-traffic-eng-01), June 1999. 5 Heinanen et al, "MPLS Mappings of Generic VPN Mechanisms", work in progress (draft-heinanen-generic-vpn-mpls-00), August 1998. 6 Jamieson et al, "MPLS VPN Architecture" work in progress (draft-jamieson-mpls-vpn-00), August 1998. 7 T. Li, "CPE based VPNs using MPLS", work in progress (draft- li-mpls-vpn-00.txt), October 1998. 8 Guerin et al, "Setting up Reservations on Explicit Paths using RSVP", work in progress (draft-guerin-expl-path-rsvp-01) November 1997. 9 L. Wu, et. al., "LDP State Machine" work in progress (draft-ietf-mpls-ldp-state-00), Feb 1999. 10 J. Ash, et. al., _LSP Modification Using CR-LDP_ work in progress (draft-ash-crlsp-modify-00.txt), July 1999. 9. Author's Addresses Osama S. Aboul-Magd Loa Andersson Nortel Networks Nortel Networks P O Box 3511 Station C Kungsgatan 34, PO Box 1788 Ottawa, ON K1Y 4H7 111 97 Stockholm, Sweden Canada Phone: +46 8 441 78 34 Phone: +1 613 763-5827 Mobile +46 70 522 78 34 Osama@nortelnetworks.com Loa_andersson@beynetworks.com Peter Ashwood-Smith Ross Callon Nortel Networks IronBridge Networks P O Box 3511 Station C 55 Hayden Avenue, Ottawa, ON K1Y 4H7 Lexington, MA 02173 Canada Phone: +1-781-402-8017 Phone: +1 613 763-4534 Rcallon@ironbridgenetworks.com Petera@nortelnetworks.com Ram Dantu Paul Doolan Alcatel USA Inc. Ennovate Networks IP Competence Center 330 Codman Hill Rd 1201 E. Campbell Road.,446-315 Marlborough MA 01719 Richadson, TX USA., 75081-2206 Phone: 978-263-2002 Phone: 972 996 2938 Pdoolan@ennovatenetworks.com Fax: 972 996 5902 Ram.dantu@aud.alcatel.com Jamoussi, et. al. draft-ietf-mpls-crldp-02.txt 26 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Nancy Feldman Andre Fredette IBM Corp. Nortel Networks 17 Skyline Drive 3 Federal Street Hawthorne NY 10532 Billerica, MA 01821 Phone: 914-784-3254 978-288-8524 Nkf@us.ibm.com Fredette@baynetworks.com Eric Gray Joel M. Halpern Lucent Technologies, Inc Institutional Venture Partners 1600 Osgood St. 650-926-5633 North Andover, MA 01847 joel@mcquillan.com Phone: 603-659-3386 Ewgray@lucent.com Juha Heinanen Fiffi Hellstrand Telia Finland, Inc. Ericsson Telecom AB Myyrmaentie 2 S-126 25 STOCKHOLM 01600 VANTAA Sweden Finland Tel: +46 8 719 4933 Tel: +358 41 500 4808 etxfiff@etxb.ericsson.se Jh@telia.fi Bilel Jamoussi Timothy E. Kilty Nortel Networks Corp. Northchurch Communications 3 Federal Street 5 Corporate Drive, Billerica, MA 01821 Andover, MA 018110 USA phone: 978 691-4656 Phone: +1 978 288-4506 tkilty@northc.com Jamoussi@nortelnetworks.com Andrew G. Malis Muckai K Girish Ascend Communications, Inc. SBC Technology Resources, 1 Robbins Road 4698 Willow Road Westford, MA 01886 Pleasanton, CA 94588 Phone: 978 952-7414 Phone: (925) 598-1263 fax: 978 392-2074 Fax: (925) 598-1321 Malis@ascend.com mgirish@tri.sbc.com Kenneth Sundell Pasi Vaananen Nortel Networks Nokia Telecommunications Architecture Lab, EMEA 3 Burlington Woods Drive, Kungsgatan 34, PO Box 1788 Burlington, MA 01803 111 97 Stockholm, Sweden Phone: +1-781-238-4981 phone: +46 8 441-7838, Pasi.vaananen@ntc.nokia.com mobile +46 70 665-7838 ksundell@nortelnetworks.com Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 27 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Tom worster Liwen Wu Nokia Alcatel U.S.A 3 Burlington Woods Dr. 44983 Knoll Square Suite 250 Ashburn, Va. 20147 Burlington MA 01803 USA Phone: (703) 724-2619 +1 617 247 2624 FAX: (703) 724-2005 tom.worster@nokia.com Liwen.wu@and.alcatel.com Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 28 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Appendix A: CRLSP Establishment Examples A.1 Strict Explicit Route Example This appendix provides an example for the setup of a strictly routed CRLSP. In this example, a specific node represents each abstract node. The sample network used here is a four node network with two edge LSRs and two core LSRs as follows: abc LSR1------LSR2------LSR3------LSR4 LSR1 generates a Label Request Message as described in Section 3.1 of this draft and sends it to LSR2. This message includes the CR- TLV. A vector of three ER-Hop TLVs composes the ER-TLV. The ER-Hop TLVs used in this example are of type 0x0801 (IPv4 prefix) with a prefix length of 32. Hence, each ER-Hop TLV identifies a specific node as opposed to a group of nodes. At LSR2, the following processing of the ER-TLV per Section 4.8.1 of this draft takes place: 1) The first hop is part of the abstract node LSR2. Therefore, the first step passes the test. Go to step 2. 2) There is a second ER-Hop, . Go to step 3. 3) LSR2 is not part of the abstract node described by the second ER-Hop . Go to Step 4. 4) LSR2 determines that it is topologically adjacent to the abstract node described by the second ER-Hop . LSR2 selects a next hop (LSR3) which is the abstract node. LSR2 deletes the first ER-Hop from the ER-TLV which now becomes . Go to Section 4.8.2. At LSR2, the following processing of Section 4.8.2 takes place: Executing algorithm 4.8.1 did not result in the removal of the ER- TLV. Also, LSR2 is not a member of the abstract node described by the first ER-Hop . Finally, the first ER-Hop is a strict hop. Therefore, processing section 4.8.2 does not result in the insertion of new ER-Hops. The selection of the next hop has been already done is step 4 of Section 4.8.1 and the processing of the ER-TLV is Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 29 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 completed at LSR2. In this case, the Label Request Message including the ER-TLV is progressed by LSR2 to LSR3. At LSR3, a similar processing to the ER-TLV takes place except that the incoming ER-TLV = and the outgoing ER-TLV is . At LSR4, the following processing of section 4.8.1 takes place: 1) The first hop is part of the abstract node LSR4. Therefore, the first step passes the test. Go to step 2. 2) There is no second ER-Hop, this indicates the end of the CRLSP. The ER-TLV is removed from the Label Request Message. Processing continues with Section 4.8.2. At LSR4, the following processing of Section 4.8.2 takes place: Executing algorithm 4.8.1 resulted in the removal of the ER-TLV. LSR4 does not add a new ER-TLV. Therefore, processing section 4.8.2 does not result in the insertion of new ER-Hops. This indicates the end of the CRLSP and the processing of the ER-TLV is completed at LSR4. At LSR4, processing of Section 3.2 is invoked. The first condition is satisfied (LSR4 is the egress end of the CRLSP and upstream mapping has been requested). Therefore, a Label Mapping Message is generated by LSR4 and sent to LSR3. At LSR3, the processing of Section 3.2 is invoked. The second condition is satisfied (LSR3 received a mapping from its downstream next hop LSR4 for a CRLSP for which an upstream request is still pending). Therefore, a Label Mapping Message is generated by LSR3 and sent to LSR2. At LSR2, a similar processing to LSR 3 takes place and a Label Mapping Message is sent back to LSR1 which completes the end-to-end CRLSP setup. A.2. Node Groups and Specific Nodes Example A request at ingress LSR to setup a CRLSP might originate from a management system or an application, the details are implementation specific. The ingress LSR uses information provided by the management system or the application and possibly also information from the routing database to calculate the explicit route and to create the Label Request Message. The Label request message carries together with other necessary information a ER-TLV defining the explicitly routed path. In our example the list of hops in the ER-Hop TLV is supposed to contain an Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 30 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 abstract node representing a group of nodes, an abstract node representing a specific node, another abstract node representing a group of nodes, and an abstract node representing a specific egress point. In--{Group 1}--{Specific A}--{Group 2}--{Specific Out: B} The ER-TLV contains four ER-Hop TLVs: 1. An ER-Hop TLV that specifies a group of LSR valid for the first abstract node representing a group of nodes (Group 1). 2. An ER-Hop TLV that indicates the specific node (Node A). 3. An ER-Hop TLV that specifies a group of LSRs valid for the second abstract node representing a group of nodes (Group 2). 4. An ER-Hop TLV that indicates the specific egress point for the CRLSP (Node B). All the ER-Hop TLVs are strictly routed nodes. The setup procedure for this CRLSP works as follows: 1. The ingress node sends the Label Request Message to a node that is a member the group of nodes indicated in the first ER-Hop TLV, following normal routing for the specific node (A). 2. The node that receives the message identifies itself as part of the group indicated in the first ER-Hop TLV, and that it is not the specific node (A) in the second. Further it realizes that the specific node (A) is not one of its next hops. 3. It keeps the ER-Hop TLVs intact and sends a Label Request Message to a node that is part of the group indicated in the first ER-Hop TLV (Group 1), following normal routing for the specific node (A). 4. The node that receives the message identifies itself as part of the group indicated in the first ER-Hop TLV, and that it is not the specific node (A) in the second ER-Hop TLV. Further it realizes that the specific node (A) is one of its next hops. 5. It removes the first ER-Hop TLVs and sends a Label Request Message to the specific node (A). 6. The specific node (A) recognizes itself in the first ER-Hop TLV. Removes the specific ER-Hop TLV. Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 31 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 7. It sends a Label Request Message to a node that is a member of the group (Group 2) indicated in the ER-Hop TLV. 8. The node that receives the message identifies itself as part of the group indicated in the first ER-Hop TLV, further it realizes that the specific egress node (B) is one of its next hops. 9. It sends a Label Request Message to the specific egress node (B). 10.The specific egress node (B) recognizes itself as the egress for the CRLSP, it returns a Label Mapping Message, that will traverse the same path as the Label Request Message in the opposite direction. Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 32 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Appendix B. QoS Service Examples B.1 Service Examples Construction of an end-to-end service is the result of the rules enforced at the edge and the treatment that packets receive at the network nodes. The rules define the traffic conditioning actions that are implemented at the edge and they include policing with pass, mark, and drop capabilities. The edge rules are expected to be defined by the mutual agreements between the service providers and their customers and they will constitute an essential part of the SLA. Therefore edge rules are not included in the signaling protocol. Packet treatment at a network node is usually referred to as the local behavior. Local behavior could be specified in many ways. One example for local behavior specification is the service frequency introduced in section 4.3.2.1, together with the resource reservation rules implemented at the nodes. Edge rules and local behaviors can be viewed as the main building blocks for the end-to-end service construction. The following table illustrates the applicability of the building block approach for constructing different services including those defined for ATM. Service PDR PBS CDR CBS EBS Service Conditioning Examples Frequency Action DS S S =PDR =PBS 0 Frequent drop>PDR TS S S S S 0 Unspecified drop>PDR,PBS mark>CDR,CBS BE inf inf inf inf 0 Unspecified - FRS S S CIR ~B_C ~B_E Unspecified drop>PDR,PBS mark>CDR,CBS,EBS ATM-CBR PCR CDVT =PCR =CDVT 0 VeryFrequent drop>PCR ATM-VBR.3(rt) PCR CDVT SCR MBS 0 Frequent drop>PCR mark>SCR,MBS ATM-VBR.3(nrt) PCR CDVT SCR MBS 0 Unspecified drop>PCR mark>SCR,MBS ATM-UBR PCR CDVT - - 0 Unspecified drop>PCR ATM-GFR.1 PCR CDVT MCR MBS 0 Unspecified drop>PCR ATM-GFR.2 PCR CDVT MCR MBS 0 Unspecified drop>PCR mark>MCR,MFS Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 33 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 int-serv-CL p m r b 0 Frequent drop>p drop>r,b S= User specified In the above table, the DS refers to a delay sensitive service where the network commits to deliver with high probability user datagrams at a rate of PDR with minimum delay and delay requirements. Datagrams in excess of PDR will be discarded. The TS refers to a generic throughput sensitive service where the network commits to deliver with high probability user datagrams at a rate of at least CDR. The user may transmit at a rate higher than CDR but datagrams in excess of CDR would have a lower probability of being delivered. The BE is the best effort service and it implies that there are no expected service guarantees from the network. B.2. Establishing CR-LSP Supporting Real-Time Applications In this scenario the customer needs to establish an LSP for supporting real-time applications such voice and video. The Delay- sensitive (DS) service is requested in this case. The first step is the specification of the traffic parameters in the signaling message. The two parameters of interest to the DS service are the PDR and the PBS and the user based on his requirements specifies their values. Since all the traffic parameters are included in the signaling message, appropriate values must be assigned to all of them. For DS service, the CDR and the CBS values are set equal to the PDR and the PBS respectively. An indication of whether the parameter values are subject to negotiation is flagged. The transport characteristics of the DS service require that Frequent frequency to be requested to reflect the real-time delay requirements of the service. In addition to the transport characteristics, both the network provider and the customer need to agree on the actions enforced at the edge. The specification of those actions is expected to be a part of the service level agreement (SLA) negotiation and is not included in the signaling protocol. For DS service, the edge action is to drop packets that exceed the PDR and the PBS specifications. The signaling message will be sent in the direction of the ER path and the LSP is established following the normal LDP procedures. Each LSR applies its admission control rules. If sufficient resources are not available and the parameter values are subject to negotiation, then the LSR could negotiate down the PDR, the PBS, or both. Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 34 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 The new parameter values are echoed back in the Label Mapping Message. LSRs might need to re-adjust their resource reservations based on the new traffic parameter values. B.3. Establishing CR-LSP Supporting Delay Insensitive Applications In this example we assume that a throughput sensitive (TS) service is requested. For resource allocation the user assigns values for PDR, PBS, CDR, and CBS. The negotiation flag is set if the traffic parameters are subject to negotiation. Since the service is delay insensitive by definition, the Unspecified frequency is signaled to indicate that the service frequency is not an issue. Similar to the previous example, the edge actions are not subject for signaling and are specified in the service level agreement between the user and the network provider. For TS service, the edge rules might include marking to indicate high discard precedence values for all packets that exceed CDR and the CBS. The edge rules will also include dropping of packets that are do not conform to neither PDR nor PBS. Each LSR of the LSP is expected to run its admission control rules and negotiate traffic parameters down if sufficient resources do not exist. The new parameter values are echoed back in the Label Mapping Message. LSRs might need to re-adjust their resources based on the new traffic parameter values. Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 35 Internet Draft Constraint-Based LSP Setup using LDP August, 1999 Full Copyright Statement _Copyright c The Internet Society (date). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. Jamoussi, et. al. draft-ietf-mpls-cr-ldp-02.txt 36