MMUSIC Working Group H. Schulzrinne Internet-Draft Columbia University Intended status: Standards Track A. Rao Expires: May 7, 2009 Cisco R. Lanphier M. Westerlund Ericsson AB M. Stiemerling (Ed.) NEC November 3, 2008 Real Time Streaming Protocol 2.0 (RTSP) draft-ietf-mmusic-rfc2326bis-19 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on May 7, 2009. Schulzrinne, et al. Expires May 7, 2009 [Page 1] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Abstract This memorandum defines RTSP version 2.0 which is a revision of the Proposed Standard RTSP version 1.0 which is defined in RFC 2326. The Real Time Streaming Protocol, or RTSP, is an application-level protocol for control over the delivery of data with real-time properties. RTSP provides an extensible framework to enable controlled, on-demand delivery of real-time data, such as audio and video. Sources of data can include both live data feeds and stored clips. This protocol is intended to control multiple data delivery sessions, provide a means for choosing delivery channels such as UDP, multicast UDP and TCP, and provide a means for choosing delivery mechanisms based upon RTP (RFC 3550). Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 9 1.1. Scope and Background . . . . . . . . . . . . . . . . . . 9 1.2. RTSP Specificication Update . . . . . . . . . . . . . . 10 1.3. Notational Conventions . . . . . . . . . . . . . . . . . 10 1.4. Terminology . . . . . . . . . . . . . . . . . . . . . . 11 1.5. Media Properties . . . . . . . . . . . . . . . . . . . . 14 1.5.1. Random Access . . . . . . . . . . . . . . . . . . . 15 1.5.2. Retention . . . . . . . . . . . . . . . . . . . . . 15 1.5.3. Content Modifications . . . . . . . . . . . . . . . 16 1.5.4. Mapping to the Attributes . . . . . . . . . . . . . 16 2. RTSP Introduction . . . . . . . . . . . . . . . . . . . . . . 17 2.1. Protocol Properties . . . . . . . . . . . . . . . . . . 17 2.2. RTSP's Relationship to HTTP . . . . . . . . . . . . . . 18 2.3. Extending RTSP . . . . . . . . . . . . . . . . . . . . . 19 2.4. Overall Operation . . . . . . . . . . . . . . . . . . . 20 2.5. RTSP States . . . . . . . . . . . . . . . . . . . . . . 21 2.6. Relationship with Other Protocols . . . . . . . . . . . 22 3. RTSP Use Cases . . . . . . . . . . . . . . . . . . . . . . . 23 3.1. On-demand Playback of Stored Content . . . . . . . . . . 23 3.2. Unicast distribution of Live Content . . . . . . . . . . 24 3.3. On-demand Playback using Multicast . . . . . . . . . . . 25 3.4. Inviting an RTSP server into a conference . . . . . . . 25 3.5. Live Content using Multicast . . . . . . . . . . . . . . 26 4. Protocol Parameters . . . . . . . . . . . . . . . . . . . . . 28 4.1. RTSP Version . . . . . . . . . . . . . . . . . . . . . . 28 4.2. RTSP IRI and URI . . . . . . . . . . . . . . . . . . . . 28 4.3. Session Identifiers . . . . . . . . . . . . . . . . . . 30 4.4. SMPTE Relative Timestamps . . . . . . . . . . . . . . . 30 4.5. Normal Play Time . . . . . . . . . . . . . . . . . . . . 30 4.6. Absolute Time . . . . . . . . . . . . . . . . . . . . . 31 Schulzrinne, et al. Expires May 7, 2009 [Page 2] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 4.7. Feature-tags . . . . . . . . . . . . . . . . . . . . . . 31 4.8. Entity Tags . . . . . . . . . . . . . . . . . . . . . . 32 5. RTSP Message . . . . . . . . . . . . . . . . . . . . . . . . 33 5.1. Message Types . . . . . . . . . . . . . . . . . . . . . 33 5.2. Message Headers . . . . . . . . . . . . . . . . . . . . 34 5.3. Message Body . . . . . . . . . . . . . . . . . . . . . . 34 5.4. Message Length . . . . . . . . . . . . . . . . . . . . . 34 6. General Header Fields . . . . . . . . . . . . . . . . . . . . 35 7. Request . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.1. Request Line . . . . . . . . . . . . . . . . . . . . . . 36 7.2. Request Header Fields . . . . . . . . . . . . . . . . . 38 8. Response . . . . . . . . . . . . . . . . . . . . . . . . . . 40 8.1. Status-Line . . . . . . . . . . . . . . . . . . . . . . 40 8.1.1. Status Code and Reason Phrase . . . . . . . . . . . 40 8.2. Response Header Fields . . . . . . . . . . . . . . . . . 43 9. Entity . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 9.1. Entity Header Fields . . . . . . . . . . . . . . . . . . 46 9.2. Entity Body . . . . . . . . . . . . . . . . . . . . . . 47 10. Connections . . . . . . . . . . . . . . . . . . . . . . . . . 48 10.1. Reliability and Acknowledgements . . . . . . . . . . . . 48 10.2. Using Connections . . . . . . . . . . . . . . . . . . . 49 10.3. Closing Connections . . . . . . . . . . . . . . . . . . 50 10.4. Timing Out Connections and RTSP Messages . . . . . . . . 51 10.5. Showing Liveness . . . . . . . . . . . . . . . . . . . . 51 10.6. Use of IPv6 . . . . . . . . . . . . . . . . . . . . . . 52 11. Capability Handling . . . . . . . . . . . . . . . . . . . . . 53 12. Pipelining Support . . . . . . . . . . . . . . . . . . . . . 55 13. Method Definitions . . . . . . . . . . . . . . . . . . . . . 56 13.1. OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . 57 13.2. DESCRIBE . . . . . . . . . . . . . . . . . . . . . . . . 58 13.3. SETUP . . . . . . . . . . . . . . . . . . . . . . . . . 60 13.3.1. Changing Transport Parameters . . . . . . . . . . . 63 13.4. PLAY . . . . . . . . . . . . . . . . . . . . . . . . . . 64 13.4.1. General Usage . . . . . . . . . . . . . . . . . . . 64 13.4.2. Aggregated Sessions . . . . . . . . . . . . . . . . 68 13.4.3. Updating current PLAY Requests . . . . . . . . . . . 68 13.4.4. Playing On-Demand Media . . . . . . . . . . . . . . 70 13.4.5. Playing Dynamic On-Demand Media . . . . . . . . . . 71 13.4.6. Playing Live Media . . . . . . . . . . . . . . . . . 71 13.4.7. Playing Live with Recording . . . . . . . . . . . . 72 13.4.8. Playing Live with Time-Shift . . . . . . . . . . . . 72 13.5. PLAY_NOTIFY . . . . . . . . . . . . . . . . . . . . . . 73 13.5.1. End-of-Stream . . . . . . . . . . . . . . . . . . . 74 13.5.2. Media-Properties-Update . . . . . . . . . . . . . . 75 13.5.3. Scale-Change . . . . . . . . . . . . . . . . . . . . 76 13.6. PAUSE . . . . . . . . . . . . . . . . . . . . . . . . . 77 13.7. TEARDOWN . . . . . . . . . . . . . . . . . . . . . . . . 79 13.8. GET_PARAMETER . . . . . . . . . . . . . . . . . . . . . 80 Schulzrinne, et al. Expires May 7, 2009 [Page 3] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 13.9. SET_PARAMETER . . . . . . . . . . . . . . . . . . . . . 81 13.10. REDIRECT . . . . . . . . . . . . . . . . . . . . . . . . 82 14. Embedded (Interleaved) Binary Data . . . . . . . . . . . . . 86 15. Status Code Definitions . . . . . . . . . . . . . . . . . . . 88 15.1. Success 1xx . . . . . . . . . . . . . . . . . . . . . . 88 15.1.1. 100 Continue . . . . . . . . . . . . . . . . . . . . 88 15.2. Success 2xx . . . . . . . . . . . . . . . . . . . . . . 88 15.2.1. 200 OK . . . . . . . . . . . . . . . . . . . . . . . 88 15.3. Redirection 3xx . . . . . . . . . . . . . . . . . . . . 88 15.3.1. 300 Multiple Choices . . . . . . . . . . . . . . . . 89 15.3.2. 301 Moved Permanently . . . . . . . . . . . . . . . 89 15.3.3. 302 Found . . . . . . . . . . . . . . . . . . . . . 89 15.3.4. 303 See Other . . . . . . . . . . . . . . . . . . . 89 15.3.5. 304 Not Modified . . . . . . . . . . . . . . . . . . 89 15.3.6. 305 Use Proxy . . . . . . . . . . . . . . . . . . . 90 15.4. Client Error 4xx . . . . . . . . . . . . . . . . . . . . 90 15.4.1. 400 Bad Request . . . . . . . . . . . . . . . . . . 90 15.4.2. 405 Method Not Allowed . . . . . . . . . . . . . . . 90 15.4.3. 451 Parameter Not Understood . . . . . . . . . . . . 90 15.4.4. 452 reserved . . . . . . . . . . . . . . . . . . . . 90 15.4.5. 453 Not Enough Bandwidth . . . . . . . . . . . . . . 91 15.4.6. 454 Session Not Found . . . . . . . . . . . . . . . 91 15.4.7. 455 Method Not Valid in This State . . . . . . . . . 91 15.4.8. 456 Header Field Not Valid for Resource . . . . . . 91 15.4.9. 457 Invalid Range . . . . . . . . . . . . . . . . . 91 15.4.10. 458 Parameter Is Read-Only . . . . . . . . . . . . . 91 15.4.11. 459 Aggregate Operation Not Allowed . . . . . . . . 91 15.4.12. 460 Only Aggregate Operation Allowed . . . . . . . . 91 15.4.13. 461 Unsupported Transport . . . . . . . . . . . . . 92 15.4.14. 462 Destination Unreachable . . . . . . . . . . . . 92 15.4.15. 463 Destination Prohibited . . . . . . . . . . . . . 92 15.4.16. 464 Data Transport Not Ready Yet . . . . . . . . . . 92 15.4.17. 465 Notification Reason Unknown . . . . . . . . . . 92 15.4.18. 470 Connection Authorization Required . . . . . . . 92 15.4.19. 471 Connection Credentials not accepted . . . . . . 93 15.4.20. 472 Failure to establish secure connection . . . . . 93 15.5. Server Error 5xx . . . . . . . . . . . . . . . . . . . . 93 15.5.1. 551 Option not supported . . . . . . . . . . . . . . 93 16. Header Field Definitions . . . . . . . . . . . . . . . . . . 94 16.1. Accept . . . . . . . . . . . . . . . . . . . . . . . . . 103 16.2. Accept-Credentials . . . . . . . . . . . . . . . . . . . 103 16.3. Accept-Encoding . . . . . . . . . . . . . . . . . . . . 104 16.4. Accept-Language . . . . . . . . . . . . . . . . . . . . 104 16.5. Accept-Ranges . . . . . . . . . . . . . . . . . . . . . 104 16.6. Allow . . . . . . . . . . . . . . . . . . . . . . . . . 105 16.7. Authorization . . . . . . . . . . . . . . . . . . . . . 105 16.8. Bandwidth . . . . . . . . . . . . . . . . . . . . . . . 105 16.9. Blocksize . . . . . . . . . . . . . . . . . . . . . . . 105 Schulzrinne, et al. Expires May 7, 2009 [Page 4] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.10. Cache-Control . . . . . . . . . . . . . . . . . . . . . 106 16.11. Connection . . . . . . . . . . . . . . . . . . . . . . . 108 16.12. Connection-Credentials . . . . . . . . . . . . . . . . . 108 16.13. Content-Base . . . . . . . . . . . . . . . . . . . . . . 109 16.14. Content-Encoding . . . . . . . . . . . . . . . . . . . . 109 16.15. Content-Language . . . . . . . . . . . . . . . . . . . . 109 16.16. Content-Length . . . . . . . . . . . . . . . . . . . . . 110 16.17. Content-Location . . . . . . . . . . . . . . . . . . . . 110 16.18. Content-Type . . . . . . . . . . . . . . . . . . . . . . 110 16.19. CSeq . . . . . . . . . . . . . . . . . . . . . . . . . . 110 16.20. Date . . . . . . . . . . . . . . . . . . . . . . . . . . 110 16.21. ETag . . . . . . . . . . . . . . . . . . . . . . . . . . 111 16.22. Expires . . . . . . . . . . . . . . . . . . . . . . . . 111 16.23. From . . . . . . . . . . . . . . . . . . . . . . . . . . 112 16.24. If-Match . . . . . . . . . . . . . . . . . . . . . . . . 112 16.25. If-Modified-Since . . . . . . . . . . . . . . . . . . . 112 16.26. If-None-Match . . . . . . . . . . . . . . . . . . . . . 113 16.27. Last-Modified . . . . . . . . . . . . . . . . . . . . . 113 16.28. Location . . . . . . . . . . . . . . . . . . . . . . . . 113 16.29. Media-Properties . . . . . . . . . . . . . . . . . . . . 113 16.30. Media-Range . . . . . . . . . . . . . . . . . . . . . . 115 16.31. Notify-Reason . . . . . . . . . . . . . . . . . . . . . 115 16.32. Pipelined-Requests . . . . . . . . . . . . . . . . . . . 115 16.33. Proxy-Authenticate . . . . . . . . . . . . . . . . . . . 116 16.34. Proxy-Authorization . . . . . . . . . . . . . . . . . . 117 16.35. Proxy-Require . . . . . . . . . . . . . . . . . . . . . 117 16.36. Proxy-Supported . . . . . . . . . . . . . . . . . . . . 117 16.37. Public . . . . . . . . . . . . . . . . . . . . . . . . . 118 16.38. Range . . . . . . . . . . . . . . . . . . . . . . . . . 119 16.39. Referer . . . . . . . . . . . . . . . . . . . . . . . . 120 16.40. Retry-After . . . . . . . . . . . . . . . . . . . . . . 120 16.41. Request-Status . . . . . . . . . . . . . . . . . . . . . 120 16.42. Require . . . . . . . . . . . . . . . . . . . . . . . . 121 16.43. RTP-Info . . . . . . . . . . . . . . . . . . . . . . . . 122 16.44. Scale . . . . . . . . . . . . . . . . . . . . . . . . . 123 16.45. Seek-Style . . . . . . . . . . . . . . . . . . . . . . . 124 16.46. Speed . . . . . . . . . . . . . . . . . . . . . . . . . 125 16.47. Server . . . . . . . . . . . . . . . . . . . . . . . . . 126 16.48. Session . . . . . . . . . . . . . . . . . . . . . . . . 126 16.49. Supported . . . . . . . . . . . . . . . . . . . . . . . 127 16.50. Timestamp . . . . . . . . . . . . . . . . . . . . . . . 127 16.51. Transport . . . . . . . . . . . . . . . . . . . . . . . 128 16.52. Unsupported . . . . . . . . . . . . . . . . . . . . . . 134 16.53. User-Agent . . . . . . . . . . . . . . . . . . . . . . . 134 16.54. Vary . . . . . . . . . . . . . . . . . . . . . . . . . . 134 16.55. Via . . . . . . . . . . . . . . . . . . . . . . . . . . 135 16.56. WWW-Authenticate . . . . . . . . . . . . . . . . . . . . 135 17. Proxies . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Schulzrinne, et al. Expires May 7, 2009 [Page 5] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 17.1. Proxies and Protocol Extensions . . . . . . . . . . . . 137 18. Caching . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 19. Security Framework . . . . . . . . . . . . . . . . . . . . . 140 19.1. RTSP and HTTP Authentication . . . . . . . . . . . . . . 140 19.2. RTSP over TLS . . . . . . . . . . . . . . . . . . . . . 140 19.3. Security and Proxies . . . . . . . . . . . . . . . . . . 141 19.3.1. Accept-Credentials . . . . . . . . . . . . . . . . . 142 19.3.2. User approved TLS procedure . . . . . . . . . . . . 143 20. Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 20.1. Base Syntax . . . . . . . . . . . . . . . . . . . . . . 145 20.2. RTSP Protocol Definition . . . . . . . . . . . . . . . . 147 20.2.1. Generic Protocol elements . . . . . . . . . . . . . 147 20.2.2. Message Syntax . . . . . . . . . . . . . . . . . . . 150 20.2.3. Header Syntax . . . . . . . . . . . . . . . . . . . 154 20.3. SDP extension Syntax . . . . . . . . . . . . . . . . . . 162 21. Security Considerations . . . . . . . . . . . . . . . . . . . 163 21.1. Remote denial of Service Attack . . . . . . . . . . . . 165 22. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 167 22.1. Feature-tags . . . . . . . . . . . . . . . . . . . . . . 167 22.1.1. Description . . . . . . . . . . . . . . . . . . . . 167 22.1.2. Registering New Feature-tags with IANA . . . . . . . 168 22.1.3. Registered entries . . . . . . . . . . . . . . . . . 168 22.2. RTSP Methods . . . . . . . . . . . . . . . . . . . . . . 168 22.2.1. Description . . . . . . . . . . . . . . . . . . . . 168 22.2.2. Registering New Methods with IANA . . . . . . . . . 168 22.2.3. Registered Entries . . . . . . . . . . . . . . . . . 169 22.3. RTSP Status Codes . . . . . . . . . . . . . . . . . . . 169 22.3.1. Description . . . . . . . . . . . . . . . . . . . . 169 22.3.2. Registering New Status Codes with IANA . . . . . . . 169 22.3.3. Registered Entries . . . . . . . . . . . . . . . . . 169 22.4. RTSP Headers . . . . . . . . . . . . . . . . . . . . . . 169 22.4.1. Description . . . . . . . . . . . . . . . . . . . . 169 22.4.2. Registering New Headers with IANA . . . . . . . . . 170 22.4.3. Registered entries . . . . . . . . . . . . . . . . . 170 22.5. Accept-Credentials . . . . . . . . . . . . . . . . . . . 171 22.5.1. Accept-Credentials policies . . . . . . . . . . . . 171 22.5.2. Accept-Credentials hash algorithms . . . . . . . . . 171 22.6. Cache-Control Cache Directive Extensions . . . . . . . 172 22.7. Media Properties . . . . . . . . . . . . . . . . . . . . 172 22.7.1. Description . . . . . . . . . . . . . . . . . . . . 173 22.7.2. Registration Rules . . . . . . . . . . . . . . . . . 173 22.7.3. Registered Values . . . . . . . . . . . . . . . . . 173 22.8. Notify-Reason header . . . . . . . . . . . . . . . . . . 173 22.8.1. Description . . . . . . . . . . . . . . . . . . . . 173 22.8.2. Registration Rules . . . . . . . . . . . . . . . . . 173 22.8.3. Registered Values . . . . . . . . . . . . . . . . . 174 22.9. Range header formats . . . . . . . . . . . . . . . . . . 174 22.10. RTP-Info header parameters . . . . . . . . . . . . . . . 174 Schulzrinne, et al. Expires May 7, 2009 [Page 6] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 22.10.1. Desctiption . . . . . . . . . . . . . . . . . . . . 174 22.10.2. Registration Rules . . . . . . . . . . . . . . . . . 175 22.10.3. Registered Values . . . . . . . . . . . . . . . . . 175 22.11. Seek-Style Policies . . . . . . . . . . . . . . . . . . 175 22.11.1. Description . . . . . . . . . . . . . . . . . . . . 175 22.11.2. Registration Rules . . . . . . . . . . . . . . . . . 175 22.11.3. Registered Values . . . . . . . . . . . . . . . . . 176 22.12. Transport Header Registries . . . . . . . . . . . . . . 176 22.12.1. Transport Protocol Specification . . . . . . . . . . 176 22.12.2. Transport modes . . . . . . . . . . . . . . . . . . 177 22.12.3. Transport Parameters . . . . . . . . . . . . . . . . 178 22.13. URI Schemes . . . . . . . . . . . . . . . . . . . . . . 178 22.13.1. The rtsp URI Scheme . . . . . . . . . . . . . . . . 178 22.13.2. The rtsps URI Scheme . . . . . . . . . . . . . . . . 179 22.13.3. The rtspu URI Scheme . . . . . . . . . . . . . . . . 180 22.14. SDP attributes . . . . . . . . . . . . . . . . . . . . . 181 22.15. Media Type Registration for text/parameters . . . . . . 182 23. References . . . . . . . . . . . . . . . . . . . . . . . . . 184 23.1. Normative References . . . . . . . . . . . . . . . . . . 184 23.2. Informative References . . . . . . . . . . . . . . . . . 186 Appendix A. Examples . . . . . . . . . . . . . . . . . . . . . . 189 A.1. Media on Demand (Unicast) . . . . . . . . . . . . . . . 189 A.2. Media on Demand using Pipelining . . . . . . . . . . . . 193 A.3. Media on Demand (Unicast) . . . . . . . . . . . . . . . 195 A.4. Single Stream Container Files . . . . . . . . . . . . . 199 A.5. Live Media Presentation Using Multicast . . . . . . . . 201 A.6. Capability Negotiation . . . . . . . . . . . . . . . . . 202 Appendix B. RTSP Protocol State Machine . . . . . . . . . . . . 204 B.1. States . . . . . . . . . . . . . . . . . . . . . . . . . 204 B.2. State variables . . . . . . . . . . . . . . . . . . . . 204 B.3. Abbreviations . . . . . . . . . . . . . . . . . . . . . 204 B.4. State Tables . . . . . . . . . . . . . . . . . . . . . . 205 Appendix C. Media Transport Alternatives . . . . . . . . . . . . 210 C.1. RTP . . . . . . . . . . . . . . . . . . . . . . . . . . 210 C.1.1. AVP . . . . . . . . . . . . . . . . . . . . . . . . 210 C.1.2. AVP/UDP . . . . . . . . . . . . . . . . . . . . . . 210 C.1.3. AVPF/UDP . . . . . . . . . . . . . . . . . . . . . . 211 C.1.4. SAVP/UDP . . . . . . . . . . . . . . . . . . . . . . 212 C.1.5. SAVPF/UDP . . . . . . . . . . . . . . . . . . . . . 212 C.1.6. RTCP usage with RTSP . . . . . . . . . . . . . . . . 212 C.2. RTP over TCP . . . . . . . . . . . . . . . . . . . . . . 213 C.2.1. Interleaved RTP over TCP . . . . . . . . . . . . . . 213 C.2.2. RTP over independent TCP . . . . . . . . . . . . . . 213 C.2.3. Handling Media Clock Time Jumps in the RTP Media Layer . . . . . . . . . . . . . . . . . . . . . . . 217 C.2.4. Handling RTP Timestamps after PAUSE . . . . . . . . 220 C.2.5. RTSP / RTP Integration . . . . . . . . . . . . . . . 223 C.2.6. Scaling with RTP . . . . . . . . . . . . . . . . . . 223 Schulzrinne, et al. Expires May 7, 2009 [Page 7] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C.2.7. Maintaining NPT synchronization with RTP timestamps . . . . . . . . . . . . . . . . . . . . . 223 C.2.8. Continuous Audio . . . . . . . . . . . . . . . . . . 223 C.2.9. Multiple Sources in an RTP Session . . . . . . . . . 223 C.2.10. Usage of SSRCs and the RTCP BYE Message During an RTSP Session . . . . . . . . . . . . . . . . . . . . 223 C.3. Future Additions . . . . . . . . . . . . . . . . . . . . 224 Appendix D. Use of SDP for RTSP Session Descriptions . . . . . . 225 D.1. Definitions . . . . . . . . . . . . . . . . . . . . . . 225 D.1.1. Control URI . . . . . . . . . . . . . . . . . . . . 225 D.1.2. Media Streams . . . . . . . . . . . . . . . . . . . 226 D.1.3. Payload Type(s) . . . . . . . . . . . . . . . . . . 227 D.1.4. Format-Specific Parameters . . . . . . . . . . . . . 227 D.1.5. Directionality of media stream . . . . . . . . . . . 227 D.1.6. Range of Presentation . . . . . . . . . . . . . . . 228 D.1.7. Time of Availability . . . . . . . . . . . . . . . . 229 D.1.8. Connection Information . . . . . . . . . . . . . . . 229 D.1.9. Entity Tag . . . . . . . . . . . . . . . . . . . . . 229 D.2. Aggregate Control Not Available . . . . . . . . . . . . 230 D.3. Aggregate Control Available . . . . . . . . . . . . . . 230 D.4. RTSP external SDP delivery . . . . . . . . . . . . . . . 231 Appendix E. Text format for Parameters . . . . . . . . . . . . . 233 Appendix F. Requirements for Unreliable Transport of RTSP . . . 234 Appendix G. Backwards Compatibility Considerations . . . . . . . 236 G.1. Play Request in Play mode . . . . . . . . . . . . . . . 236 G.2. Using Persistent Connections . . . . . . . . . . . . . . 236 Appendix H. Open Issues . . . . . . . . . . . . . . . . . . . . 237 Appendix I. Changes . . . . . . . . . . . . . . . . . . . . . . 238 Appendix J. Acknowledgements . . . . . . . . . . . . . . . . . . 245 J.1. Contributors . . . . . . . . . . . . . . . . . . . . . . 245 Appendix K. RFC Editor Consideration . . . . . . . . . . . . . . 247 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 248 Intellectual Property and Copyright Statements . . . . . . . . . 249 Schulzrinne, et al. Expires May 7, 2009 [Page 8] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 1. Introduction 1.1. Scope and Background This memo defines version 2.0 of the Real Time Streaming Protocol (RTSP 2.0) which is an application-level protocol for control over the delivery of data with real-time properties, typically streaming media. Streaming media is, for instance, video on demand or audio live streaming. Put simply, RTSP acts as a "network remote control" for multimedia servers, as you know it from your TV set. The protocol operates between RTSP 2.0 clients and servers, but also supports the usage of RTSP 2.0 proxies between clients and servers. Basically, clients can request information about streaming media from setranrvers, by asking for a description of the media or use media description provided externally. Based on the media description clients can request to play out the media, pause it, or stop it completely, as known from a regular TV remote control. The requested media can consist of multiple audio and video streams that are delivered as a time-synchronized streams from servers to clients. This memorandum describes the use of RTSP over a reliable connection based transport level protocol, such as TCP. For security, TLS over a connection oriented transport is supported. There is no dependency on an special RTSP connection in the protocol. Instead, an RTSP server maintains a session labeled by an identifier to associate groups of media streams and their states. An RTSP session is not tied to a transport-level connection such as a TCP connection. During a session, a client may open and close multiple reliable transport connections to the server to issue RTSP requests for that session. The set of streams to be controlled in an RTSP session is defined by a presentation description. This memorandum does not define a format for the presentation description. However Appendix D describes how SDP [RFC4566] is used for this purpose. The streams controlled by RTSP may use RTP [RFC3550] for their data transport, but the operation of RTSP does not depend on the transport mechanism used to carry continuous media. RTSP is intentionally similar in syntax and operation to HTTP/1.1 [RFC2616] so that extension mechanisms to HTTP may also be applied to RTSP. The RTSP 2.0 protocol supports the following operations: Schulzrinne, et al. Expires May 7, 2009 [Page 9] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Retrieval of media from media server: The client can either request a presentation description via RTSP DESCRIBE, HTTP or some other method. If the presentation is being multicast, the presentation description contains the multicast addresses and ports to be used for the continuous media. If the presentation is to be sent only to the client via unicast, the client provides the destination. Invitation of a media server to a conference: A media server can be "invited" to join an existing conference to play back media into the presentation. This mode is useful, for example, in distributed teaching applications. Several parties in the conference may take turns "pushing the remote control buttons". Note: This functionality will require RTSP external application level functionality. RTSP requests may be handled by proxies, tunnels and caches as in HTTP/1.1 [RFC2616]. 1.2. RTSP Specificication Update This memorandum specifies RTSP 2.0 which is an update of RTSP 1.0, a proposed standard defined in [RFC2326]. The goal of this version is to correct the many flaws that have been identified in RTSP 1.0 since its publication. The corrections are such that backwards compatibility was impossible. Thus a new version was deemed the most appropriate solution to get a more functional protocol. There are no plans to revise RTSP 1.0. Appendix I catalogs the changes of this version in relation to RTSP 1.0. RTSP 2.0 as specified in this memo has reduced functionality compared to RTSP 1.0 and aims at specifying the RTSP core, functionality and rules for extensions, and basic interaction with the media delivery protocol RTP [RFC3550]. Any other functionality would need to be published as extension documents. This specification provides rules for such extensions and defines registries to avoid naming collisions. 1.3. Notational Conventions Since some of the definitions and syntax are identical to HTTP/1.1, this specification only points to the section where they are defined rather than copying it. For brevity, [HX.Y] is to be taken to refer to Section X.Y of the current HTTP/1.1 specification ([RFC2616]). All the mechanisms specified in this document are described in both prose and the Augmented Backus-Naur form (ABNF) described in detail Schulzrinne, et al. Expires May 7, 2009 [Page 10] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 in [RFC5234]. Indented and smaller-type paragraphs are used to provide informative background and motivation. This is intended to give readers who were not involved with the formulation of the specification an understanding of why things are the way they are in RTSP. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. The word, "unspecified" is used to indicate functionality or features that are not defined in this specification. Such functionality cannot be used in a standardized manner without further definition in an extension specification to RTSP. 1.4. Terminology Some of the terminology has been adopted from HTTP/1.1 [RFC2616]. Terms not listed here are defined as in HTTP/1.1. Aggregate control: The concept of controlling multiple streams using a single timeline, generally maintained by the server. A client, for example, uses aggregate control when it issues a single play or pause message to simultaneously control both the audio and video in a movie. A session which is under aggregate control is referred to as an aggregated session. Aggregate control URI: The URI used in an RTSP request to refer to and control an aggregated session. It normally, but not always, corresponds to the presentation URI specified in the session description. See Section 13.3 for more information. Conference: A multiparty, multimedia presentation, where "multi" implies greater than or equal to one. Client: The client requests media service from the media server. Connection: A transport layer virtual circuit established between two programs for the purpose of communication. Container file: A file which may contain multiple media streams which often constitutes a presentation when played together. The concept of a container file is not embedded in the protocol. However, RTSP servers may offer aggregate control on the media streams within these files. Schulzrinne, et al. Expires May 7, 2009 [Page 11] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Continuous media: Data where there is a timing relationship between source and sink; that is, the sink needs to reproduce the timing relationship that existed at the source. The most common examples of continuous media are audio and motion video. Continuous media can be real-time (interactive or conversational), where there is a "tight" timing relationship between source and sink, or streaming (playback), where the relationship is less strict. Entity: The information transferred as the payload of a request or response. An entity consists of meta-information in the form of entity-header fields and content in the form of an entity-body, as described in Section 9. Feature-tag: A tag representing a certain set of functionality, i.e. a feature. IRI: Internationalized Resource Identifier, is the same as an URI, with the exception that it allows characters from the whole Universal Character Set (Unicode/ISO 10646), rather than the US- ASCII only. See [RFC3987] for more information. Live: Normally used to describe a presentation or session with media coming from an ongoing event. This generally results in the session having an unbound or only loosely defined duration, and sometimes no seek operations are possible. Media initialization: Datatype/codec specific initialization. This includes such things as clock rates, color tables, etc. Any transport-independent information which is required by a client for playback of a media stream occurs in the media initialization phase of stream setup. Media parameter: Parameter specific to a media type that may be changed before or during stream playback. Media server: The server providing playback services for one or more media streams. Different media streams within a presentation may originate from different media servers. A media server may reside on the same host or on a different host from which the presentation is invoked. Media server indirection: Redirection of a media client to a different media server. (Media) stream: A single media instance, e.g., an audio stream or a video stream as well as a single whiteboard or shared application group. When using RTP, a stream consists of all RTP and RTCP packets created by a source within an RTP session. Schulzrinne, et al. Expires May 7, 2009 [Page 12] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Message: The basic unit of RTSP communication, consisting of a structured sequence of octets matching the syntax defined in Section 20 and transmitted over a connection or a connectionless transport. Non-Aggregated Control: Control of a single media stream. This is only possible in RTSP sessions with a single media. Participant: Member of a conference. A participant may be a machine, e.g., a playback server. Presentation: A set of one or more streams presented to the client as a complete media feed and described by a presentation description as defined below. Presentations with more than one media stream are often handled in RTSP under aggregate control. Presentation description: A presentation description contains information about one or more media streams within a presentation, such as the set of encodings, network addresses and information about the content. Other IETF protocols such as SDP ([RFC4566]) use the term "session" for a presentation. The presentation description may take several different formats, including but not limited to the session description protocol format, SDP. Response: An RTSP response. If an HTTP response is meant, that is indicated explicitly. Request: An RTSP request. If an HTTP request is meant, that is indicated explicitly. Request-URI: The URI used in a request to indicate the resource on which the request is to be performed. RTSP agent: Refers to either an RTSP client, an RTSP server, or an RTSP Proxy. In this specification, there are many capabilities that are common to these three entities such as the capability to send requests or receive responses. This term will be used when describing functionality that is applicable to all three of these entities. RTSP session: A stateful abstraction upon which the main control methods of RTSP operate. An RTSP session is a server entity; it is created, maintained and destroyed by the server. It is established by an RTSP server upon the completion of a successful SETUP request (when a 200 OK response is sent) and is labelled with a session identifier at that time. The session exists until timed out by the server or explicitly removed by a TEARDOWN request. An RTSP session is a stateful entity; an RTSP server Schulzrinne, et al. Expires May 7, 2009 [Page 13] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 maintains an explicit session state machine (see Appendix A) where most state transitions are triggered by client requests. The existence of a session implies the existence of state about the session's media streams and their respective transport mechanisms. A given session can have one or more media streams associated with it. An RTSP server uses the session to aggregate control over multiple media streams. Transport initialization: The negotiation of transport information (e.g., port numbers, transport protocols) between the client and the server. URI: Universal Resource Identifier, see [RFC3986]. The URIs used in RTSP are generally URLs as they give a location for the resource. As URLs are a subset of URIs, they will be referred to as URIs to cover also the cases when an RTSP URI would not be an URL. URL: Universal Resource Locator, is an URI which identifies the resource through its primary access mechanism, rather than identifying the resource by name or by some other attribute(s) of that resource. 1.5. Media Properties When RTSP handles media it is important to consider the different properties a media instance for playback can have. This specification considers the below listed media properties in its protocol operations. They are derived from the differencies between a number of supported usages. On-demand: Media that has a fixed (given) duration that doesn't change during the life time of the RTSP session and are known at the time of the creation of the session. It is expected that the content of the media will not change, even if the representation, i.e encoding, quality, etc, may change. Generally one can seek within the media i.e. randomly access any range of the media stream to playback. Dynamic On-demand: This is a variation of the on-demand case where external methods are used to manipulate the actual content of the media setup for the RTSP session. The main example is where a playlist determines the content of the session. Live: Live media represents a progressing content stream (such as broadcast TV) where the duration may or may not be known. It is not seakable, only the content presently being delivered can be accessed. Schulzrinne, et al. Expires May 7, 2009 [Page 14] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Live with Recording: A Live stream that is combined with a server side capability to store and retain the content of the live session for random access playback within the part of the already recorded content. The actual behavior of the media stream is very much depending on the retention policy for the media stream. Either the server will be able to capture the complete media stream, or it will have a limitation in how much will be retained. The media range will dynamically change as the session progress. For servers with a limited amount of storage available for recording, there will be a sliding window that goes forwards while data is made available and content that is older than the limitation will be discarded. Considering the above usages one get the following media properties and their different instance values. 1.5.1. Random Access Random Access, i.e. if one can request that the playback point is moved from one point in the media duration to another. The following different values are considered: Random Access: Yes the media are seekable to any out of a large number of points within the media. Due to media encoding limitations a particular point may not be reachable, but seeking to a point close by is enabled. A floating point number of seconds may be provied to express the worst case distance between random access points. Return To Start: Seeking is only possible to begining of the content. No seeking: Seeking is not possible at all. 1.5.2. Retention Media may have different retention policy in place that affect the operation on the media. The following different media retention policies are envisioned and taken into consideration where applicable. Unlimited: The media will not be removed as long as the RTSP session are in existence. Time Limited: The media will at least not be removed before given wall clock time. After that time it may or may not be available any more. Schulzrinne, et al. Expires May 7, 2009 [Page 15] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Duration limited: Each indiviudal unit of the media will be retained for the specified duration. 1.5.3. Content Modifications There is also the question of how the content may change during time for a give media resource: Unmutable: The content of the media will not change, even if the representation, i.e encoding, quality, etc, may change. Dynamic: Between explicit updates the media content will not change, but the content may change due to external methods or triggers, such as playlists. Time Progressing: As times progress new content will become available. If the content also is retained it will become longer and longer as everything between the start point and the point in currently being made available can be accessed. 1.5.4. Mapping to the Attributes This section exemplifies how one would map the above listed usages to the properties and their values. On-demand: Random Access: Random Access=5s, Content Modifications: Unmutable, Retention: unlimted or time limited. Dynamic On-demand: Random Access: Random Access=3s, Content Modifications: Dynamic, Retention: unlimted or time limited. Live: Random Access: No seeking, Content Modifications: Time Progressing, Retention: Duration limited=0.0s Live with Recording: Random Access: Random Access=3s, Content Modifications: Time Progressing, Retention: Duration limited=2H Schulzrinne, et al. Expires May 7, 2009 [Page 16] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 2. RTSP Introduction 2.1. Protocol Properties RTSP has the following properties: Extendable: New methods and parameters can be easily added to RTSP. Secure: RTSP re-uses web security mechanisms, either at the transport level (TLS, [RFC5246]) or within the protocol itself. All HTTP authentication mechanisms such as basic ([RFC2616]) and digest authentication ([RFC2617]) are directly applicable. Transport-independent: RTSP does not preclude the use of unreliable datagram protocol (UDP) ([RFC0768]) as it would be possible to implement application-level reliability. The use of a connectionless datagram protocol such as UDP requires additional definition that may be provided as extensions to the core RTSP specification. The reliable stream protocol TCP ([RFC0793]) and the secured reliable stream protocol TLS over TCP [RFC5246] are the currently defined transport protocols for RTSP messages. Media-delivery protocol independent: The operation of RTSP does not depend on the transport mechanism used to carry continuous media. While most real-time media will use RTP as a transport protocol, RTSP does not preclude the use of other protocols such as MPEG-2 [ISO.13818-1.2000]. The use of other protocols requires additional definition that may be provided as extensions to the core RTSP specification. Multi-server capable: Each media stream within a presentation can reside on a different server. The client automatically establishes several concurrent control sessions with the different media servers. Media synchronization in those cases is performed at the transport level. Separation of stream control and conference initiation: Stream control is divorced from inviting a media server to a conference. In particular, SIP [RFC3261] or H.323 [ITU.H323.1996] may be used to invite a server to a conference; however, the exact procedures are unspecified. Suitable for professional applications: RTSP supports frame- level accuracy through SMPTE time stamps to allow remote digital editing. Schulzrinne, et al. Expires May 7, 2009 [Page 17] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Presentation description neutral: The protocol does not impose a particular presentation description or metafile format and can convey the type of format to be used. However, the presentation description is required to contain at least one RTSP URI. Proxy and firewall friendly: The protocol should be readily handled by both application and transport-layer (SOCKS [RFC1961]) firewalls. A firewall may need to understand the SETUP method to open a "hole" for the media stream. HTTP-friendly: Where sensible, RTSP reuses HTTP concepts, so that the existing infrastructure can be reused. This infrastructure includes PICS (Platform for Internet Content Selection [W3C.REC-PICS-services] [W3C.REC-PICS-labels]) for associating labels with content. However, RTSP does not just add methods to HTTP since controlling continuous media requires server state in most cases. Appropriate server control: If a client can start a stream, it needs to be able to stop a stream. Servers should not start streaming to clients in such a way that clients cannot stop the stream. Transport negotiation: The client can negotiate the transport method prior to actually needing to process a continuous media stream. 2.2. RTSP's Relationship to HTTP RTSP is intentionally similar in syntax and operation to HTTP/1.1 [RFC2616] so that extension mechanisms to HTTP can in some cases also be applied to RTSP. However, RTSP differs in a number of important aspects from HTTP: * RTSP introduces a number of new methods and has a different protocol identifier. * RTSP has the notion of a session built into the protocol. * An RTSP server needs to maintain state in almost all cases, as opposed to the stateless nature of HTTP. * Both an RTSP server and client can issue requests. * Data is usually carried out-of-band by a different protocol. Session descriptions returned in a DESCRIBE response (see Section 13.2) and interleaving of RTP with RTSP over TCP are exceptions to this rule (see Section 14). Schulzrinne, et al. Expires May 7, 2009 [Page 18] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 * RTSP is defined to use ISO 10646 (UTF-8) rather than ISO 8859-1, consistent with HTML internationalization efforts [RFC2070]. * The Request-URI always contains the absolute URI. Because of backward compatibility with a historical blunder, HTTP/1.1 [RFC2616] carries only the absolute path in the request and puts the host name in a separate header field. This makes "virtual hosting" easier, where a single host with one IP address hosts several document trees. 2.3. Extending RTSP Since not all media servers have the same functionality, media servers by necessity will support different sets of requests. For example: o A server may not be capable of seeking (absolute positioning) if it is to support live events only. o Some servers may not support setting stream parameters and thus not support GET_PARAMETER and SET_PARAMETER. o Some server may support an RTSP extension. It is up to the creators of presentation descriptions not to ask the impossible of a server. This situation is similar in HTTP/1.1 [RFC2616], where the methods described in [H19.5] are not likely to be supported across all servers. RTSP can be extended in three ways, listed here in order of the magnitude of changes supported: o Existing methods can be extended with new parameters, e.g. headers, as long as these parameters can be safely ignored by the recipient. If the client needs negative acknowledgement when a method extension is not supported, a tag corresponding to the extension may be added in the field of the Require or Proxy- Require headers (see Section 16.35). o New methods can be added. If the recipient of the message does not understand the request, it MUST respond with error code 501 (Not Implemented) so that the sender can avoid using this method again. A client may also use the OPTIONS method to inquire about methods supported by the server. The server MUST list the methods it supports using the Public response header. Schulzrinne, et al. Expires May 7, 2009 [Page 19] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o A new version of the protocol can be defined, allowing almost all aspects (except the position of the protocol version number) to change. A new version of the protocol MUST be registered through an IETF standard track document. The basic capability discovery mechanism can be used to both discover support for a certain feature and to ensure that a feature is available when performing a request. For detailed explanation of this see Section 11. 2.4. Overall Operation Each presentation and media stream is identified by an RTSP URI. The overall presentation and the properties of the media the presentation is composed of are defined by a presentation description file, the format of which is outside the scope of this specification. The presentation description file may be obtained by the client using HTTP or other means such as email and may not necessarily be stored on the media server. For the purposes of this specification, a presentation description is assumed to describe one or more presentations, each of which maintains a common time axis. For simplicity of exposition and without loss of generality, it is assumed that the presentation description contains exactly one such presentation. A presentation may contain several media streams. The presentation description file contains a description of the media streams making up the presentation, including their encodings, language, and other parameters that enable the client to choose the most appropriate combination of media. In this presentation description, each media stream that is individually controllable by RTSP is identified by an RTSP URI, which points to the media server handling that particular media stream and names the stream stored on that server. Several media streams can be located on different servers; for example, audio and video streams can be split across servers for load sharing. The description also enumerates which transport methods the server is capable of. Besides the media parameters, the network destination address and port need to be determined. Several modes of operation can be distinguished: Unicast: The media is transmitted to the source of the RTSP request or the requested destination, with the port number chosen by the client. Alternatively, the media is transmitted on the same reliable stream as RTSP. Schulzrinne, et al. Expires May 7, 2009 [Page 20] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Multicast, server chooses address: The media server picks the multicast address and port. This is the typical case for a live or near-media-on-demand transmission. The address is provided by the session description. Multicast, client chooses address: If the server is to participate in an existing multicast conference, the multicast address, port and encryption key are given by the conference description, established by means outside the scope of this specification, for example by a SIP created conference. 2.5. RTSP States RTSP controls a stream which may be sent via a separate protocol, independent of the control channel. For example, RTSP control may be transported on a TCP connection while the media data is conveyed via UDP. Thus, data delivery continues even if no RTSP requests are received by the media server. Also, during its lifetime a single media stream may be controlled by RTSP requests issued sequentially on different TCP connections. Therefore, the server needs to maintain "session state" to be able to correlate RTSP requests with a stream. The state transitions are described in Appendix A. Many methods in RTSP do not contribute to state. However, the following play a central role in defining the allocation and usage of stream resources on the server: SETUP, PLAY, PAUSE, REDIRECT, and TEARDOWN. SETUP: Causes the server to allocate resources for a stream and create an RTSP session. PLAY: Starts data transmission on a stream allocated via SETUP. PAUSE: Temporarily halts a stream without freeing server resources. REDIRECT: Indicates that the session should be moved to a new server or location TEARDOWN: Frees resources associated with the stream. The RTSP session ceases to exist on the server. RTSP methods that contribute to state use the Session header field (Section 16.49) to identify the RTSP session whose state is being manipulated. The server generates session identifiers in response to SETUP requests (Section 13.3). Schulzrinne, et al. Expires May 7, 2009 [Page 21] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 2.6. Relationship with Other Protocols RTSP has some overlap in functionality with HTTP. It also may interact with HTTP in that the initial contact with streaming content will often be made through a web page. The current protocol specification aims to allow different hand-off points between a web server and the media server implementing RTSP. For example, the presentation description can be retrieved using HTTP or RTSP, which reduces round trips in web-browser-based scenarios, yet also allows for stand alone RTSP servers and clients which do not rely on HTTP at all. However, RTSP differs fundamentally from HTTP in that most data delivery takes place out-of-band in a different protocol. HTTP is an asymmetric protocol where the client issues requests and the server responds. In RTSP, both the media client and media server can issue requests. RTSP requests are also stateful; they may set parameters and continue to control a media stream long after the request has been acknowledged. Re-using HTTP functionality has advantages in at least two areas, namely security and proxies. The requirements are very similar, so having the ability to adopt HTTP work on caches, proxies and authentication is valuable. RTSP assumes the existence of a presentation description format that can express both static and temporal properties of a presentation containing several media streams. Session Description Protocol (SDP) [RFC4566] is generally the format of choice; however, RTSP is not bound to it. For data delivery, most real-time media will use RTP as a transport protocol. While RTSP works well with RTP, it is not tied to RTP. Schulzrinne, et al. Expires May 7, 2009 [Page 22] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 3. RTSP Use Cases This section describes the most important and considered use cases for RTSP. They are listed in descending order of importance in regards to ensuring that all necessary functionality is present. This specification only fully supports usage of the two first. Also in these first two cases, there are special cases or exceptions that are not supported without extensions, e.g. the redirection of media to another address than the controlling entity. 3.1. On-demand Playback of Stored Content An RTSP capable server stores content suitable for being streamed to a client. A client desiring playback of any of the stored content uses RTSP to set up the media transport required to deliver the desired content. RTSP is then used to initiate, halt and manipulate the actual transmission (playout) of the content. RTSP is also required to provide necessary description and synchronization information for the content. The above high level description can be broken down into a number of functions that RTSP needs to be capable of. Presentation Description: Provide initialization information about the presentation (content); for example, which media codecs are needed for the content. Other information that is important includes the number of media stream the presentation contains, the transport protocols used for the media streams, and identifiers for these media streams. This information is required before setup of the content is possible and to determine if the client is even capable of using the content. This information need not be sent using RTSP; other external protocols can be used to transmit the transport presentation descriptions. Two good examples are the use of HTTP [RFC2616] or email to fetch or receive presentation descriptions like SDP [RFC4566] Setup: Set up some or all of the media streams in a presentation. The setup itself consist of selecting the protocol for media transport and the necessary parameters for the protocol, like addresses and ports. Control of Transmission: After the necessary media streams have been established the client can request the server to start transmitting the content. The client must be allowed to start or stop the transmission of the content at arbitrary times. The client must also be able to start the transmission at any Schulzrinne, et al. Expires May 7, 2009 [Page 23] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 point in the timeline of the presentation. Synchronization: For media transport protocols like RTP [RFC3550] it might be beneficial to carry synchronization information within RTSP. This may be due to either the lack of inter-media synchronization within the protocol itself, or the potential delay before the synchronization is established (which is the case for RTP when using RTCP). Termination: Terminate the established contexts. For this use case there are a number of assumptions about how it works. These are: On-Demand content: The content is stored at the server and can be accessed at any time during a time period when it is intended to be available. Independent sessions: A server is capable of serving a number of clients simultaneously, including from the same piece of content at different points in that presentations time-line. Unicast Transport: Content for each individual client is transmitted to them using unicast traffic. It is also possible to redirect the media traffic to a different destination than that of the entity controlling the traffic. However, allowing this without appropriate mechanisms for checking that the destination approves of this allows for distributed denial of service attacks (DDoS). 3.2. Unicast distribution of Live Content This use cases is similar to the above on-demand content case (see Section 3.1) the difference is the nature of the content itself. Live content is continuously distributed as it becomes available from a source; i.e., the main difference from on-demand is that one starts distributing content before the end of it has become available to the server. In many cases the consumer of live content is only interested in consuming what is actually happens "now"; i.e., very similar to broadcast TV. However in this case it is assumed that there exist no broadcast or multicast channel to the users, and instead the server functions as a distribution node, sending the same content to multiple receivers, using unicast traffic between server and client. This unicast traffic and the transport parameters are individually negotiated for each receiving client. Schulzrinne, et al. Expires May 7, 2009 [Page 24] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Another aspect of live content is that it often has a very limited time of availability, as it is only is available for the duration of the event the content covers. An example of such a live content could be a music concert which lasts 2 hour and starts at a predetermined time. Thus there is need to announce when and for how long the live content is available. In some cases, the server providing live content may be saving some or all of the content to allow clients to pause the stream and resume it from the paused point, or to "rewind" and play continuously from a point earlier than the live point. Hence, this use case does not necessarily exclude playing from other than the live point of the stream, playing with scales other than 1.0, etc. 3.3. On-demand Playback using Multicast It is possible to use RTSP to request that media be delivered to a multicast group. The entity setting up the session (the controller) will then control when and what media is delivered to the group. This use case has some potential for denial of service attacks by flooding a multicast group. Therefore, a mechanism is needed to indicate that the group actually accepts the traffic from the RTSP server. An open issue in this use case is how one ensures that all receivers listening to the multicast or broadcast receives the session presentation configuring the receivers. This memo has to rely on a external solution to solve this issue. 3.4. Inviting an RTSP server into a conference If one has an established conference or group session, it is possible to have an RTSP server distribute media to the whole group. Transmission to the group is simplest when controlled by a single participant or leader of the conference. Shared control might be possible, but would require further investigation and possibly extensions. This use case assumes that there exists either multicast or a conference focus that redistribute media to all participants. This use case is intended to be able to handle the following scenario: A conference leader or participant (hereafter called the controller) has some pre-stored content on an RTSP server that he wants to share with the group. The controller sets up an RTSP session at the streaming server for this content and retrieves the session description for the content. The destination for the media content is set to the shared multicast group or conference focus. Schulzrinne, et al. Expires May 7, 2009 [Page 25] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 When desired by the controller, he/she can start and stop the transmission of the media to the conference group. There are several issues with this use case that are not solved by this core specification for RTSP: Denial of service: To avoid an RTSP server from being an unknowing participant in a denial of service attack the server needs to be able to verify the destination's acceptance of the media. Such a mechanism to verify the approval of received media does not yet exist; instead, only policies can be used, which can be made to work in controlled environments. Distributing the presentation description to all participants in the group: To enable a media receiver to correctly decode the content the media configuration information needs to be distributed reliably to all participants. This will most likely require support from an external protocol. Passing control of the session: If it is desired to pass control of the RTSP session between the participants, some support will be required by an external protocol to exchange state information and possibly floor control of who is controlling the RTSP session. If there interest in this use case, further work is required on the necessary extensions. 3.5. Live Content using Multicast This use case in its simplest form does not require any use of RTSP at all; this is what multicast conferences being announced with SAP [RFC2974] and SDP are intended to handle. However in use cases where more advanced features like access control to the multicast session are desired, RTSP could be used for session establishment. A client desiring to join a live multicasted media session with cryptographic (encryption) access control could use RTSP in the following way. The source of the session announces the session and gives all interested an RTSP URI. The client connects to the server and requests the presentation description, allowing configuration for reception of the media. In this step it is possible for the client to use secured transport and any desired level of authentication; for example, for billing or access control. An RTSP link also allows for load balancing between multiple servers. If these were the only goals, they could be achieved by simply using HTTP. However, for cases where the sender likes to keep track of Schulzrinne, et al. Expires May 7, 2009 [Page 26] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 each individual receiver of a session, and possibly use the session as a side channel for distributing key-updates or other information on a per-receiver basis, and the full set of receivers is not know prior to the session start, the state establishment that RTSP provides can be beneficial. In this case a client would establish an RTSP session for this multicast group with the RTSP server. The RTSP server will not transmit any media, but instead will point to the multicast group. The client and server will be able to keep the session alive for as long as the receiver participates in the session thus enabling, for example, the server to push updates to the client. This use case will most likely not be able to be implemented without some extensions to the server-to-client push mechanism. Here the PLAY_NOTIFY method (see Section 13.5) with a suitable extension could provide clear benefits. Schulzrinne, et al. Expires May 7, 2009 [Page 27] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 4. Protocol Parameters 4.1. RTSP Version HTTP specification section [H3.1] applies, with "HTTP" replaced by "RTSP". This specification defines version 2.0 of RTSP. 4.2. RTSP IRI and URI RTSP 2.0 defines and registers three URI schemas "rtsp", "rtsps" and "rtspu". The usage of the last, "rtspu", is unspecified in RTSP 2.0, and is defined here to register and reserve the URI scheme that is defined in RTSP 1.0. The "rtspu" scheme indicates undefined transport of the RTSP messages over unreliable transport (UDP). The syntax of "rtsp" and "rtsps" URIs has been changed from RTSP 1.0. This specification also defines the format of the RTSP IRI [RFC3987] that can be used as RTSP resource identifiers and locators, in web pages, user interfaces, on paper, etc. However, the RTSP request message format only allows usage of the absolute URI format. The RTSP IRI format SHALL use the rules and transformation for IRIs defined in [RFC3987]. This way RTSP 2.0 URIs for request can be produced from an RTSP IRI. The RTSP IRI and URI are both syntax restricted compared to the generic syntax defined in [RFC3986] and RFC [RFC3987]: o An absolute URI requires the authority part; i.e., a host identity must be provided. o Parameters in the path element are prefixed with the reserved separator ";". The RTSP URI and IRI is case sensitive, with the exception of those parts that [RFC3986] and [RFC3987] defines as case-insensitive; for example, the scheme and host part. The fragment identifier is used as defined in sections 3.5 and 4.3 of [RFC3986], i.e. the fragment is to be stripped from the URI by the requestor and not included in the request. The user agent also needs to interpret the value of the fragment based on the media type the request relates to; i.e., the media type indicated in Content-Type header in the response to DESCRIBE. The syntax of any URI query string is unspecified and responder (usually the server) specific. The query is, from the requestor's perspective, an opaque string and needs to be handled as such. Schulzrinne, et al. Expires May 7, 2009 [Page 28] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The URI scheme "rtsp" requires that commands are issued via a reliable protocol (within the Internet, TCP), while the scheme "rtsps" identifies a reliable transport using secure transport (TLS [RFC5246], see (Section 19). For the scheme "rtsp", if no port number is provided in the authority part of the URI port number 554 SHALL be used. For the scheme "rtsps", the TCP port 322 is registered and SHALL be assumed. A presentation or a stream is identified by a textual media identifier, using the character set and escape conventions of URIs [RFC3986]. URIs may refer to a stream or an aggregate of streams; i.e., a presentation. Accordingly, requests described in (Section 13) can apply to either the whole presentation or an individual stream within the presentation. Note that some request methods can only be applied to streams, not presentations, and vice versa. For example, the RTSP URI: rtsp://media.example.com:554/twister/audiotrack may identify the audio stream within the presentation "twister", which can be controlled via RTSP requests issued over a TCP connection to port 554 of host media.example.com. Also, the RTSP URI: rtsp://media.example.com:554/twister identifies the presentation "twister", which may be composed of audio and video streams, but could also be something else like a random media redirector. This does not imply a standard way to reference streams in URIs. The presentation description defines the hierarchical relationships in the presentation and the URIs for the individual streams. A presentation description may name a stream "a.mov" and the whole presentation "b.mov". The path components of the RTSP URI are opaque to the client and do not imply any particular file system structure for the server. This decoupling also allows presentation descriptions to be used with non-RTSP media control protocols simply by replacing the scheme in the URI. Schulzrinne, et al. Expires May 7, 2009 [Page 29] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 4.3. Session Identifiers Session identifiers are strings of any arbitrary length but with a minimum length of 8 characters. A session identifier MUST be chosen cryptographically random (see [RFC4086]) and MUST be at least 8 characters long (can contain a maximum of 48 bits of entropy) to make guessing it more difficult. It is RECOMMENDED that it contains 128 bits of entropy, i.e. approxamitely 22 characters from a high quality generator. (see Section 21.) However, it needs to be noted that the session identifier does not provide any security against session hijacking unless it is kept confidential between client, server and trusted proxies. 4.4. SMPTE Relative Timestamps A SMPTE relative timestamp expresses time relative to the start of the clip. Relative timestamps are expressed as SMPTE time codes for frame-level access accuracy. The time code has the format hours:minutes:seconds:frames.subframes, with the origin at the start of the clip. The default smpte format is "SMPTE 30 drop" format, with frame rate is 29.97 frames per second. Other SMPTE codes MAY be supported (such as "SMPTE 25") through the use of alternative use of "smpte-type". For SMPTE 30, the "frames" field in the time value can assume the values 0 through 29. The difference between 30 and 29.97 frames per second is handled by dropping the first two frame indices (values 00 and 01) of every minute, except every tenth minute. If the frame and the subframe values are zero, they may be omitted. Subframes are measured in one- hundredth of a frame. Examples: smpte=10:12:33:20- smpte=10:07:33- smpte=10:07:00-10:07:33:05.01 smpte-25=10:07:00-10:07:33:05.01 4.5. Normal Play Time Normal play time (NPT) indicates the stream absolute position relative to the beginning of the presentation, not to be confused with the Network Time Protocol (NTP) [RFC1305]. The timestamp consists of a decimal fraction. The part left of the decimal may be expressed in either seconds or hours, minutes, and seconds. The part right of the decimal point measures fractions of a second. Schulzrinne, et al. Expires May 7, 2009 [Page 30] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The beginning of a presentation corresponds to 0.0 seconds. Negative values are not defined. The special constant "now" is defined as the current instant of a live event. It MAY only be used for live events, and SHALL NOT be used for on-demand (i.e., non-live) content. NPT is defined as in DSM-CC [ISO.13818-6.1995]: "Intuitively, NPT is the clock the viewer associates with a program. It is often digitally displayed on a VCR. NPT advances normally when in normal play mode (scale = 1), advances at a faster rate when in fast scan forward (high positive scale ratio), decrements when in scan reverse (high negative scale ratio) and is fixed in pause mode. NPT is (logically) equivalent to SMPTE time codes." Examples: npt=123.45-125 npt=12:05:35.3- npt=now- The syntax conforms to ISO 8601 [ISO.8601.2000]. The npt-sec notation is optimized for automatic generation, the npt-hhmmss notation for consumption by human readers. The "now" constant allows clients to request to receive the live feed rather than the stored or time-delayed version. This is needed since neither absolute time nor zero time are appropriate for this case. 4.6. Absolute Time Absolute time is expressed as ISO 8601 [ISO.8601.2000] timestamps, using UTC (GMT). Fractions of a second may be indicated. Example for November 8, 1996 at 14h37 and 20 and a quarter seconds UTC: 19961108T143720.25Z 4.7. Feature-tags Feature-tags are unique identifiers used to designate features in RTSP. These tags are used in Require (Section 16.42), Proxy-Require (Section 16.35), Proxy-Supported (Section 16.36), and Unsupported (Section 16.52) header fields. A feature-tag definition MUST indicate which combination of clients, servers or proxies they applies to. The creator of a new RTSP feature-tag should either prefix the feature-tag with a reverse domain name (e.g., Schulzrinne, et al. Expires May 7, 2009 [Page 31] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 "com.example.mynewfeature" is an apt name for a feature whose inventor can be reached at "example.com"), or register the new feature-tag with the Internet Assigned Numbers Authority (IANA) (see IANA Section 22). The usage of feature-tags is further described in Section 11 that deals with capability handling. 4.8. Entity Tags Entity tags are opaque strings that are used to compare two entities from the same resource, for example in caches or to optimize setup after a redirect. Further explanation is present in [H3.11]. For an explanation of how to compare entity tags see [H13.3]. Entity tags can be carried in the ETag header (see Section 16.21) or in SDP (see Appendix D.1.9). Entity tags are used in RTSP to make some methods conditional. The methods are made conditional through the inclusion of headers, see Section 16.24 and Section 16.26. Note that RTSP entity tags apply to the complete presentation; i.e., both the session description and the individual media streams. Thus entity tags can be used to verify at setup time after a redirect that the same session description applies to the media at the new location using the If-Match header. Schulzrinne, et al. Expires May 7, 2009 [Page 32] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 5. RTSP Message RTSP is a text-based protocol and uses the ISO 10646 character set in UTF-8 encoding (RFC 3629 [RFC3629]). Lines SHALL be terminated by CRLF. Text-based protocols make it easier to add optional parameters in a self-describing manner. Since the number of parameters and the frequency of commands is low, processing efficiency is not a concern. Text-based protocols, if done carefully, also allow easy implementation of research prototypes in scripting languages such as Tcl, Visual Basic and Perl. The ISO 10646 character set avoids tricky character set switching, but is invisible to the application as long as US-ASCII is being used. This is also the encoding used for RTCP [RFC3550]. ISO 8859-1 translates directly into Unicode with a high-order octet of zero. ISO 8859-1 characters with the most-significant bit set are represented as 1100001x 10xxxxxx. (See RFC 3629 [RFC3629]) Requests contain methods, the object the method is operating upon and parameters to further describe the method. Methods are idempotent unless otherwise noted. Methods are also designed to require little or no state maintenance at the media server. 5.1. Message Types RTSP messages consist of requests from client to server or server to client and responses in the reverse direction. Request Section 7 and Response Section 8 messages use the generic message format of RFC 822 [9] for transferring entities (the payload of the message). Both types of message consist of a start-line, zero or more header fields (also known as "headers"), an empty line (i.e., a line with nothing preceding the CRLF) indicating the end of the header fields, and possibly a message-body. generic-message = start-line *(message-header CRLF) CRLF [ message-body ] start-line = Request-Line | Status-Line In the interest of robustness, servers SHOULD ignore any empty line(s) received where a Request-Line is expected. In other words, if the server is reading the protocol stream at the beginning of a message and receives a CRLF first, it should ignore the CRLF. Schulzrinne, et al. Expires May 7, 2009 [Page 33] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 5.2. Message Headers See [H4.2]. Unknown message headers SHALL be ignored by a RTSP server or client. An RTSP Proxy SHALL forward unknown message headers. Message headers defined outside of this specification that are required to be interpret by the RTSP agent will need to use feature tags (Section 4.7) and include it in the appropriate Require (Section 16.42) or Proxy-Require (Section 16.35) header. 5.3. Message Body See [H4.3]. Unlike HTTP, the presence of a message-body in either a request or a response MUST be signaled by the inclusion of a Content-Length header field (see Section 16.16). 5.4. Message Length When a message body is included with a message, the length of that body is determined by one of the following (in order of precedence): 1. Any response message which MUST NOT include a message body (such as the 1xx, 204, and 304 responses) is always terminated by the first empty line after the header fields, regardless of the entity-header fields present in the message. (Note: An empty line is a line with nothing preceding the CRLF.) 2. If a Content-Length header field (Section 16.16) is present, its value in bytes represents the length of the message-body. If this header field is not present, a value of zero is assumed. Unlike an HTTP message, an RTSP message MUST contain a Content-Length header field whenever it contains a message body. Note that RTSP does not support the HTTP/1.1 "chunked" transfer coding (see [H3.6.1]). Given the moderate length of presentation descriptions returned, the server should always be able to determine its length, even if it is generated dynamically, making the chunked transfer encoding unnecessary. Schulzrinne, et al. Expires May 7, 2009 [Page 34] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 6. General Header Fields See [H4.5], except that the Pragma, Trailer, Transfer-Encoding, Upgrade, and Warning headers are not defined. RTSP further defines the CSeq, Pipelined-Requests, Proxy-Supported and Timestamp headers. The general headers are listed in Table 1: +--------------------+--------------------+ | Header Name | Defined in Section | +--------------------+--------------------+ | Cache-Control | Section 16.10 | | | | | Connection | Section 16.11 | | | | | CSeq | Section 16.19 | | | | | Date | Section 16.20 | | | | | Media-Properties | Section 16.29 | | | | | Media-Range | Section 16.30 | | | | | Pipelined-Requests | Section 16.32 | | | | | Proxy-Supported | Section 16.36 | | | | | Seek-Style | Section 16.45 | | | | | Supported | Section 16.49 | | | | | Timestamp | Section 16.50 | | | | | Via | Section 16.55 | +--------------------+--------------------+ Table 1: The general headers used in RTSP Schulzrinne, et al. Expires May 7, 2009 [Page 35] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 7. Request A request message uses the format outlined below regardless of the direction of a request, client to server or server to client: o Request line, containing the method to be applied to the resource, the identifier of the resource, and the protocol version in use; o Zero or more Header lines, that can be of the following types: general (Section 6), request (Section 7.2), or entity (Section 9.1); o One empty line (CRLF) to indicate the end of the header section; o Optionally a message body (entity), consisting of one or more lines. The length of the message body in bytes is indicated by the Content-Length entity header. 7.1. Request Line The request line provides the key information about the request: what method, on what resources and using which RTSP version. The methods that are defined by this specification are listed in Table 2. Schulzrinne, et al. Expires May 7, 2009 [Page 36] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 +---------------+--------------------+ | Method | Defined in Section | +---------------+--------------------+ | DESCRIBE | Section 13.2 | | | | | GET_PARAMETER | Section 13.8 | | | | | OPTIONS | Section 13.1 | | | | | PAUSE | Section 13.6 | | | | | PLAY | Section 13.4 | | | | | PLAY_NOTIFY | Section 13.5 | | | | | REDIRECT | Section 13.10 | | | | | SETUP | Section 13.3 | | | | | SET_PARAMETER | Section 13.9 | | | | | TEARDOWN | Section 13.7 | +---------------+--------------------+ Table 2: The RTSP Methods The syntax of the RTSP request line is the following: CRLF Note: This syntax cannot be freely changed in future versions of RTSP. This line needs to remain parsable by older RTSP implementations since it indicates the RTSP version of the message. In contrast to HTTP/1.1 [RFC2616], RTSP requests identify the resource through an absolute RTSP URI (scheme, host, and port) (see Section 4.2) rather than just the absolute path. HTTP/1.1 requires servers to understand the absolute URI, but clients are supposed to use the Host request header. This is purely needed for backward-compatibility with HTTP/1.0 servers, a consideration that does not apply to RTSP. An asterisk "*" can be used instead of an absolute URI in the Request-URI part to indicate that the request does not apply to a particular resource, but to the server or proxy itself, and is only allowed when the request method does not necessarily apply to a resource. Schulzrinne, et al. Expires May 7, 2009 [Page 37] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 For example: OPTIONS * RTSP/2.0 An OPTIONS in this form will determine the capabilities of the server or the proxy that first receives the request. If the capability of the specific server needs to be determined, without regard to the capability of an intervening proxy, the server should be addressed explicitly with an absolute URI that contains the server's address. For example: OPTIONS rtsp://example.com RTSP/2.0 7.2. Request Header Fields The RTSP headers in Table 3 can be included in a request, as request headers, to modify the specifics of the request. Some of these headers may also be used in the response to a request, as response headers, to modify the specifics of a response (Section 8.2). +--------------------+--------------------+ | Header | Defined in Section | +--------------------+--------------------+ | Accept | Section 16.1 | | | | | Accept-Credentials | Section 16.2 | | | | | Accept-Encoding | Section 16.3 | | | | | Accept-Language | Section 16.4 | | | | | Authorization | Section 16.7 | | | | | Bandwidth | Section 16.8 | | | | | Blocksize | Section 16.9 | | | | | From | Section 16.23 | | | | | If-Match | Section 16.24 | | | | | If-Modified-Since | Section 16.25 | | | | | If-None-Match | Section 16.26 | | | | | Notify-Reason | Section 16.31 | | | | Schulzrinne, et al. Expires May 7, 2009 [Page 38] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Proxy-Require | Section 16.35 | | | | | Range | Section 16.38 | | | | | Referer | Section 16.39 | | | | | Request-Status | Section 16.41 | | | | | Require | Section 16.42 | | | | | Scale | Section 16.44 | | | | | Session | Section 16.48 | | | | | Speed | Section 16.46 | | | | | Supported | Section 16.49 | | | | | Transport | Section 16.51 | | | | | User-Agent | Section 16.53 | +--------------------+--------------------+ Table 3: The RTSP request headers Detailed headers definition are provided in Section 16. New request headers may be defined. If the receiver of the request is required to understand the request header, the request MUST include a corresponding feature tag in a Require or Proxy-Require header to ensure the processing of the header. actually happens. Schulzrinne, et al. Expires May 7, 2009 [Page 39] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 8. Response [H6] applies except that HTTP-Version is replaced by RTSP-Version. Also, RTSP defines additional status codes and does not define some of the HTTP codes. The valid response codes and the methods they can be used with are listed in Table 4. After receiving and interpreting a request message, the recipient responds with an RTSP response message. 8.1. Status-Line The first line of a Response message is the Status-Line, consisting of the protocol version followed by a numeric status code and the textual phrase associated with the status code, with each element separated by SP characters. No CR or LF is allowed except in the final CRLF sequence. SP SP CRLF 8.1.1. Status Code and Reason Phrase The Status-Code element is a 3-digit integer result code of the attempt to understand and satisfy the request. These codes are fully defined in Section 15. The Reason-Phrase is intended to give a short textual description of the Status-Code. The Status-Code is intended for use by automata and the Reason-Phrase is intended for the human user. The client is not required to examine or display the Reason- Phrase. The first digit of the Status-Code defines the class of response. The last two digits do not have any categorization role. There are 5 values for the first digit: 1xx: Informational - Request received, continuing process 2xx: Success - The action was successfully received, understood, and accepted 3rr: Redirection - Further action needs to be taken in order to complete the request 4xx: Client Error - The request contains bad syntax or cannot be fulfilled Schulzrinne, et al. Expires May 7, 2009 [Page 40] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 5xx: Server Error - The server failed to fulfill an apparently valid request The individual values of the numeric status codes defined for RTSP/2.0, and an example set of corresponding Reason-Phrases, are presented in Table 4. The reason phrases listed here are only recommended; they may be replaced by local equivalents without affecting the protocol. Note that RTSP adopts most HTTP/1.1 [RFC2616] status codes and adds RTSP-specific status codes starting at x50 to avoid conflicts with newly defined HTTP status codes. RTSP status codes are extensible. RTSP applications are not required to understand the meaning of all registered status codes, though such understanding is obviously desirable. However, applications MUST understand the class of any status code, as indicated by the first digit, and treat any unrecognized response as being equivalent to the x00 status code of that class, with the exception that an unrecognized response MUST NOT be cached. For example, if an unrecognized status code of 431 is received by the client, it can safely assume that there was something wrong with its request and treat the response as if it had received a 400 status code. In such cases, user agents SHOULD present to the user the entity returned with the response, since that entity is likely to include human- readable information which will explain the unusual status. +------+----------------------------------------+-----------------+ | Code | Reason | Method | +------+----------------------------------------+-----------------+ | 100 | Continue | all | | | | | | | | | | 200 | OK | all | | | | | | | | | | 300 | Multiple Choices | all | | | | | | 301 | Moved Permanently | all | | | | | | 302 | Found | all | | | | | | 303 | See Other | all | | | | | | 305 | Use Proxy | all | | | | | | | | | | 400 | Bad Request | all | | | | | | 401 | Unauthorized | all | Schulzrinne, et al. Expires May 7, 2009 [Page 41] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | 402 | Payment Required | all | | | | | | 403 | Forbidden | all | | | | | | 404 | Not Found | all | | | | | | 405 | Method Not Allowed | all | | | | | | 406 | Not Acceptable | all | | | | | | 407 | Proxy Authentication Required | all | | | | | | 408 | Request Timeout | all | | | | | | 410 | Gone | all | | | | | | 411 | Length Required | all | | | | | | 412 | Precondition Failed | DESCRIBE, SETUP | | | | | | 413 | Request Entity Too Large | all | | | | | | 414 | Request-URI Too Long | all | | | | | | 415 | Unsupported Media Type | all | | | | | | 451 | Parameter Not Understood | SET_PARAMETER | | | | | | 452 | reserved | n/a | | | | | | 453 | Not Enough Bandwidth | SETUP | | | | | | 454 | Session Not Found | all | | | | | | 455 | Method Not Valid In This State | all | | | | | | 456 | Header Field Not Valid | all | | | | | | 457 | Invalid Range | PLAY, PAUSE | | | | | | 458 | Parameter Is Read-Only | SET_PARAMETER | | | | | | 459 | Aggregate Operation Not Allowed | all | | | | | | 460 | Only Aggregate Operation Allowed | all | | | | | | 461 | Unsupported Transport | all | | | | | Schulzrinne, et al. Expires May 7, 2009 [Page 42] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | 462 | Destination Unreachable | all | | | | | | 463 | Destination Prohibited | SETUP | | | | | | 464 | Data Transport Not Ready Yet | PLAY | | | | | | 465 | Notification Reason Unknown | PLAY_NOTIFY | | | | | | 470 | Connection Authorization Required | all | | | | | | 471 | Connection Credentials not accepted | all | | | | | | 472 | Failure to establish secure connection | all | | | | | | | | | | 500 | Internal Server Error | all | | | | | | 501 | Not Implemented | all | | | | | | 502 | Bad Gateway | all | | | | | | 503 | Service Unavailable | all | | | | | | 504 | Gateway Timeout | all | | | | | | 505 | RTSP Version Not Supported | all | | | | | | 551 | Option not support | all | +------+----------------------------------------+-----------------+ Table 4: Status codes and their usage with RTSP methods 8.2. Response Header Fields The response-header fields allow the request recipient to pass additional information about the response which cannot be placed in the Status-Line. These header fields give information about the server and about further access to the resource identified by the Request-URI. All headers currently classified as response headers are listed in Table 5. Schulzrinne, et al. Expires May 7, 2009 [Page 43] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 +------------------------+--------------------+ | Header | Defined in Section | +------------------------+--------------------+ | Accept-Credentials | Section 16.2 | | | | | Accept-Ranges | Section 16.5 | | | | | Connection-Credentials | Section 16.12 | | | | | ETag | Section 16.21 | | | | | Location | Section 16.28 | | | | | Proxy-Authenticate | Section 16.33 | | | | | Public | Section 16.37 | | | | | Range | Section 16.38 | | | | | Retry-After | Section 16.40 | | | | | RTP-Info | Section 16.43 | | | | | Scale | Section 16.44 | | | | | Session | Section 16.48 | | | | | Server | Section 16.47 | | | | | Speed | Section 16.46 | | | | | Transport | Section 16.51 | | | | | Unsupported | Section 16.52 | | | | | Vary | Section 16.54 | | | | | WWW-Authenticate | Section 16.56 | +------------------------+--------------------+ Table 5: The RTSP response headers Response-header field names can be extended reliably only in combination with a change in the protocol version. However the usage of feature-tags in the request allows the responding party to learn the capability of the receiver of the response. New or experimental header fields MAY be given the semantics of response-header fields if all parties in the communication recognize them to be response-header Schulzrinne, et al. Expires May 7, 2009 [Page 44] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 fields. Unrecognized header fields in responses are treated as entity-header fields. Schulzrinne, et al. Expires May 7, 2009 [Page 45] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 9. Entity Request and Response messages MAY transfer an entity if not otherwise restricted by the request method or response status code. An entity consists of entity-header fields and an entity-body, although some responses will only include the entity-headers. The SET_PARAMETER and GET_PARAMETER request and response, and DESCRIBE response MAY have an entity. All 4xx and 5xx responses MAY also have an entity. In this section, both sender and recipient refer to either the client or the server, depending on who sends and who receives the entity. 9.1. Entity Header Fields Entity-header fields define meta-information about the entity-body or, if no body is present, about the resource identified by the request. The entity header fields are listed in Table 6. +------------------+--------------------+ | Header | Defined in Section | +------------------+--------------------+ | Allow | Section 16.6 | | | | | Content-Base | Section 16.13 | | | | | Content-Encoding | Section 16.14 | | | | | Content-Language | Section 16.15 | | | | | Content-Length | Section 16.16 | | | | | Content-Location | Section 16.17 | | | | | Content-Type | Section 16.18 | | | | | Expires | Section 16.22 | | | | | Last-Modified | Section 16.27 | +------------------+--------------------+ Table 6: The RTSP entity headers The extension-header mechanism allows additional entity-header fields to be defined without changing the protocol, but these fields cannot be assumed to be recognizable by the recipient. Unrecognized header fields SHOULD be ignored by the recipient and forwarded by proxies. Schulzrinne, et al. Expires May 7, 2009 [Page 46] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 9.2. Entity Body See [H7.2] with the addition that an RTSP message with an entity body MUST include the Content-Type and Content-Length headers. Schulzrinne, et al. Expires May 7, 2009 [Page 47] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 10. Connections RTSP requests can be transmitted using the two different connection scenarios listed below: o persistent - a transport connection is used for several request/ response transactions; o transient - a transport connection is used for a single request/ response transaction. RFC 2326 attempted to specify an optional mechanism for transmitting RTSP messages in connectionless mode over a transport protocol such as UDP. However, it was not specified in sufficient detail to allow for interoperable implementations. In an attempt to reduce complexity and scope, and due to lack of interest, RTSP 2.0 does not attempt to define a mechanism for supporting RTSP over UDP or other connectionless transport protocols. A side-effect of this is that RTSP requests SHALL NOT be sent to multicast groups since no connection can be established with a specific receiver in multicast environments. Certain RTSP headers, such as the CSeq header (Section 16.19), which may appear to be relevant only to connectionless transport scenarios are still retained and must be implemented according to the specification. In the case of CSeq, it is quite useful for matching responses to requests if the requests are pipelined (see Section 12). It is also useful in proxies for keeping track of the different requests when aggregating several client requests on a single TCP connection. 10.1. Reliability and Acknowledgements When RTSP messages are transmitted using reliable transport protocols, they MUST NOT be retransmitted at the RTSP protocol level. Instead, the implementation must rely on the underlying transport to provide reliability. The RTSP implementation may use any indication of reception acknowledgement of the message from the underlying transport protocols to optimize the RTSP behavior. If both the underlying reliable transport such as TCP and the RTSP application retransmit requests, each packet loss or message loss may result in two retransmissions. The receiver typically cannot take advantage of the application-layer retransmission since the transport stack will not deliver the application-layer retransmission before the first attempt has reached the receiver. If the packet loss is caused by congestion, multiple retransmissions at different layers will exacerbate the Schulzrinne, et al. Expires May 7, 2009 [Page 48] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 congestion. Lack of acknowledgement of an RTSP request should be handled within the constraints of the connection timeout considerations described below (Section 10.4). 10.2. Using Connections A TCP transport can be used for both persistent connections (for several message exchanges) and transient connections (for a single message exchange). Implementations of this specification MUST support RTSP over TCP. The scheme of the RTSP URI (Section 4.2) indicates the default port that the server will listen on. A server MUST handle both persistent and transient connections. Transient connections facilitate mechanisms for fault tolerance. They also allow for application layer mobility. A server and client pair that support transient connections can survive the loss of a TCP connection; e.g., due to a NAT timeout. When the client has discovered that the TCP connection has been lost, it can set up a new one when there is need to communicate again. A persistent connection MAY be used for all transactions between the server and client, including messages for multiple RTSP sessions. However a persistent connection MAY also be closed after a few message exchanges. For example, a client may use a persistent connection for the initial SETUP and PLAY message exchanges in a session and then close the connection. Later, when the client wishes to send a new request, such as a PAUSE for the session, a new connection would be opened. This connection may either be transient or persistent. An RTSP agent SHOULD NOT have more than one connection to the server at any given point. If a client or proxy handles multiple RTSP sessions on the same server, it SHOULD use only one connection for managing those sessions. This saves connection resources on the server. It also reduces complexity by and enabling the server to maintain less state about its sessions and connections. Unlike HTTP, RTSP allows a server to send requests to a client. However, this can be supported only if a client establishes a persistent connection with the server. In cases where a persistent connection does not exist between a server and its client, due to the lack of a signalling channel the server may be forced to drop an RTSP session without notifying the client. An example of such a case is Schulzrinne, et al. Expires May 7, 2009 [Page 49] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 when the server desires to send a REDIRECT request for an RTSP session to the client but is not able to do so because it cannot reach the client. Without a persistent connection between the client and the server, the media server has no reliable way of reaching the client. Also, this is the only way that requests from a server to its client are likely to traverse firewalls. In light of the above, it is RECOMMENDED that clients use persistent connections whenever possible. A client that supports persistent connections MAY "pipeline" its requests (see Section 12). 10.3. Closing Connections The client MAY close a connection at any point when no outstanding request/response transactions exist for any RTSP session being managed through the connection. The server, however, SHOULD NOT close a connection until all RTSP sessions being managed through the connection have been timed out (Section 16.48). A server SHOULD NOT close a connection immediately after responding to a session-level TEARDOWN request for the last RTSP session being controlled through the connection. Instead, it should wait for a reasonable amount of time for the client to receive the TEARDOWN response, take appropriate action, and initiate the connection closing. The server SHOULD wait at least 10 seconds after sending the TEARDOWN response before closing the connection. This is to ensure that the client has time to issue a SETUP for a new session on the existing connection after having torn the last one down. 10 seconds should give the client ample opportunity get its message to the server. A server SHOULD NOT close the connection directly as a result of responding to a request with an error code. Certain error responses such as "460 Only Aggregate Operation Allowed" (Section 15.4.12) are used for negotiating capabilities of a server with respect to content or other factors. In such cases, it is inefficient for the server to close a connection on an error response. Also, such behavior would prevent implementation of advanced/special types of requests or result in extra overhead for the client when testing for new features. On the flip side, keeping connections open after sending an error response poses a Denial of Service security risk (Section 21). If a server closes a connection while the client is attempting to send a new request, the client will have to close its current Schulzrinne, et al. Expires May 7, 2009 [Page 50] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 connection, establish a new connection and send its request over the new connection. An RTSP message should not be terminated by closing the connection. Such a message MAY be considered to be incomplete by the receiver and discarded. An RTSP message is properly terminated as defined in Section 5. 10.4. Timing Out Connections and RTSP Messages Receivers of a request (responder) SHOULD respond to requests in a timely manner even when a reliable transport such as TCP is used. Similarly, the sender of a request (requestor) SHOULD wait for a sufficient time for a response before concluding that the responder will not be acting upon its request. A responder SHOULD respond to all requests within 5 seconds. If the responder recognizes that processing of a request will take longer than 5 seconds, it SHOULD send a 100 (Continue) response as soon as possible. It SHOULD continue sending a 100 response every 5 seconds thereafter until it is ready to send the final response to the requestor. After sending a 100 response, the receiver MUST send a final response indicating the success or failure of the request. A requestor SHOULD wait at least 10 seconds for a response before concluding that the responder will not be responding to its request. After receiving a 100 response, the requestor SHOULD continue waiting for further responses. If more than 10 seconds elapses without receiving any response, the requestor MAY assume that the responder is unresponsive and abort the connection. A requestor SHOULD wait longer than 10 seconds for a response if it is experiencing significant transport delays on its connection to the responder. The requestor is capable of determining the RTT of the request/response cycle using the Timestamp header (Section 16.50) in any RTSP request. 10.5. Showing Liveness The mechanisms for showing liveness of the client is, any RTSP request with a Session header, if RTP & RTCP is used an RTCP message, or through any other used media protocol capable of indicating liveness of the RTSP client. It is RECOMMENDED that a client does not wait to the last second of the timeout before trying to send a liveness message. The RTSP message may be lost or when using reliable protocols, such as TCP, the message may take some time to arrive safely at the receiver. To show liveness between RTSP request issued to accomplish other things, the following mechanisms can be Schulzrinne, et al. Expires May 7, 2009 [Page 51] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 used, in descending order of preference: RTCP: If RTP is used for media transport RTCP SHOULD be used. If RTCP is used to report transport statistics, it SHALL also work as keep alive. The server can determine the client by used network address and port together with the fact that the client is reporting on the servers SSRC(s). A downside of using RTCP is that it only gives statistical guarantees to reach the server. However that probability is so low that it can be ignored in most cases. For example, a session with 60 seconds timeout and enough bitrate assigned to RTCP messages to send a message from client to server on average every 5 seconds. That client have for a network with 5 % packet loss, the probability to fail showing liveness sign in that session within the timeout interval of 2.4*E-16. In sessions with shorter timeout times, or much higher packet loss, or small RTCP bandwidths SHOULD also use any of the mechanisms below. SET_PARAMETER: When using SET_PARAMETER for keep alive, no body SHOULD be included. This method is the RECOMMENDED RTSP method to use in request only intended to perform keep-alive. OPTIONS: This method does also work. However it causes the server to perform more unnecessary processing and result in bigger responses than necessary for the task. The reason for this is that the server needs to determine what capabilities that are associated with the media resource to correctly populate the Public and Allow headers. The timeout parameter MAY be included in a SETUP response, and SHALL NOT be included in requests. The server uses it to indicate to the client how long the server is prepared to wait between RTSP commands or other signs of life before closing the session due to lack of activity (see below and Appendix B). The timeout is measured in seconds, with a default of 60 seconds. The length of the session timeout SHALL NOT be changed in a established session. 10.6. Use of IPv6 Explicit IPv6 support was not present in RTSP 1.0 (RFC 2326). RTSP 2.0 has been updated for explicit IPv6 support. Implementations of RTSP 2.0 MUST understand literal IPv6 addresses in URIs and headers. Schulzrinne, et al. Expires May 7, 2009 [Page 52] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 11. Capability Handling This section describes the available capability handling mechanism which allows RTSP to be extended. Extensions to this version of the protocol are basically done in two ways. First, new headers can be added. Secondly, new methods can be added. The capability handling mechanism is designed to handle both cases. When a method is added, the involved parties can use the OPTIONS method to discover wether it is supported. This is done by issuing a OPTIONS request to the other party. Depending on the URI it will either apply in regards to a certain media resource, the whole server in general, or simply the next hop. The OPTIONS response MUST contain a Public header which declares all methods supported for the indicated resource. It is not necessary to use OPTIONS to discover support of a method, the client could simply try the method. If the receiver of the request does not support the method it will respond with an error code indicating the the method is either not implemented (501) or does not apply for the resource (405). The choice between the two discovery methods depends on the requirements of the service. Feature-Tags are defined to handle functionality additions that are not new methods. Each feature-tag represents a certain block of functionality. The amount of functionality that a feature-tag represents can vary significantly. A feature-tag can for example represent the functionality a single RTSP header provides. Another feature-tag can represent much more functionality, such as the "play.basic" feature-tag which represents the minimal playback implementation. Feature-tags are used to determine wether the client, server or proxy supports the functionality that is necessary to achieve the desired service. To determine support of a feature-tag, several different headers can be used, each explained below: Supported: The supported header is used to determine the complete set of functionality that both client and server have. The intended usage is to determine before one needs to use a functionality that it is supported. It can be used in any method, however OPTIONS is the most suitable one as it at the same time determines all methods that are implemented. When sending a request the requestor declares all its capabilities by including all supported feature-tags. This results in that the receiver learns the requestors feature support. The receiver then includes its set of features in the response. Schulzrinne, et al. Expires May 7, 2009 [Page 53] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Proxy-Supported: The Proxy-Supported header is used similar to the Supported header, but instead of giving the supported functionality of the client or server it provides both the requestor and the responder a view of what functionality the proxy chain between the two supports. Proxies are required to add this header whenever the Supported header is present, but proxies may independently of the requestor add it. Require: The Require header can be included in any request where the end-point, i.e. the client or server, is required to understand the feature to correctly perform the request. This can, for example, be a SETUP request where the server is required to understand a certain parameter to be able to set up the media delivery correctly. Ignoring this parameter would not have the desired effect and is not acceptable. Therefore the end-point receiving a request containing a Require MUST negatively acknowledge any feature that it does not understand and not perform the request. The response in cases where features are not supported are 551 (Option Not Supported). Also the features that are not supported are given in the Unsupported header in the response. Proxy-Require: This method has the same purpose and workings as Require except that it only applies to proxies and not the end- point. Features that needs to be supported by both proxies and end-point needs to be included in both the Require and Proxy- Require header. Unsupported: This header is used in a 551 error response, to indicate which feature(s) that was not supported. Such a response is only the result of the usage of the Require and/or Proxy-Require header where one or more feature where not supported. This information allows the requestor to make the best of situations as it knows which features are not supported. Schulzrinne, et al. Expires May 7, 2009 [Page 54] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 12. Pipelining Support Pipelining is a general method to improve performance of request response protocols by allowing the requesting entity to have more than one request outstanding and send them over the same persistent connection. For RTSP where the relative order of requests will matter it is important to maintain the order of the requests. Because of this the the responding entity SHALL process the incoming requests in their sending order. The sending order can be determined by the CSeq header and its sequence number. For TCP the delivery order will be the same as the sending order. The processing of the request SHALL also have been finished before processing the next request from the same entity. The responses MUST be sent in the order the requests was processed. RTSP 2.0 has extended support for pipelining compared to RTSP 1.0. The major improvement is to allow all requests to setup and initiate media playback to be pipelined after each other. This is accomplished by the utilization of the Pipelined-Requests header (see Section 16.32). This header allows a client to request that two or more requests is to be processed in the same RTSP session context which the first request creates. In other words a client can request that two or more media streams are set-up and then played without needing to wait for a single response. This speeds up the initial startup time for an RTSP session with at least one RTT. If a pipelined request builds on the succesful completion of one or more prior requests the requestor must verify that all requests were executed as expected. A common example will be two SETUP requests and a PLAY request. In case one of the SETUP fails unexpectedly, the PLAY request can still be succesfully executed. However, not as expected by the requesting client as only a single media instead of two will be played. In this case the client can send a PAUSE request, correct the failing SETUP request and then request it to be played. Schulzrinne, et al. Expires May 7, 2009 [Page 55] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 13. Method Definitions The method indicates what is to be performed on the resource identified by the Request-URI. The method name is case-sensitive. New methods may be defined in the future. Method names SHALL NOT start with a $ character (decimal 24) and MUST be a token as defined by the ABNF [RFC5234] in the syntax chapter Section 20. The methods are summarized in Table 7. +---------------+-----------+--------+--------------+---------------+ | method | direction | object | Server req. | Client req. | +---------------+-----------+--------+--------------+---------------+ | DESCRIBE | C -> S | P,S | recommended | recommended | | | | | | | | GET_PARAMETER | C -> S | P,S | optional | optional | | | | | | | | | S -> C | | | | | | | | | | | OPTIONS | C -> S | P,S | R=Req, | Sd=Req, R=Opt | | | | | Sd=Opt | | | | | | | | | | S -> C | | | | | | | | | | | PAUSE | C -> S | P,S | required | required | | | | | | | | PLAY | C -> S | P,S | required | required | | | | | | | | PLAY_NOTIFY | S -> C | P,S | required | required | | | | | | | | REDIRECT | S -> C | P,S | optional | required | | | | | | | | SETUP | C -> S | S | required | required | | | | | | | | SET_PARAMETER | C -> S | P,S | required | optional | | | | | | | | | S -> C | | | | | | | | | | | TEARDOWN | C -> S | P,S | required | required | +---------------+-----------+--------+--------------+---------------+ Table 7: Overview of RTSP methods, their direction, and what objects (P: presentation, S: stream) they operate on. Legend: R=Respond, Sd=Send, Opt: Optional, Req: Required Schulzrinne, et al. Expires May 7, 2009 [Page 56] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Note on Table 7: GET_PARAMETER is recommended, but not required. For example, a fully functional server can be built to deliver media without any parameters. SET_PARAMETER is required however due to its usage for keep-alive. PAUSE is now required due to that it is the only way of getting out of the state machines play state without terminating the whole session. If an RTSP agent does not support a particular method, it MUST return 501 (Not Implemented) and the requesting RTSP agent, in turn, SHOULD NOT try this method again for the given agent / resource combination. An RTSP proxy whos main function is to log or audit and not modify transport or media handling in any way MAY forward RTSP messages with unknown methods. Note, the proxy stil needs to perform the minimal required processing, like adding the Via header. 13.1. OPTIONS The semantics of the RTSP OPTIONS method is equivalent to that of the HTTP OPTIONS method described in [H9.2]. In RTSP however, OPTIONS is bi-directional, in that a client can request it to a server and vice versa. A client MUST implement the capability to send an OPTIONS request and a server or a proxy MUST implement the capability to respond to an OPTIONS request. The client, server or proxy MAY also implement the converse of their required capability. An OPTIONS request may be issued at any time. Such a request does not modify the session state. However, it may prolong the session lifespan (see below). The URI in an OPTIONS request determines the scope of the request and the corresponding response. If the Request- URI refers to a specific media resource on a given host, the scope is limited to the set of methods supported for that media resource by the indicated RTSP agent. A Request-URI with only the host address limits the scope to the specified RTSP agent's general capabilities without regard to any specific media. If the Request-URI is an asterisk ("*"), the scope is limited to the general capabilities of the next hop (i.e. the RTSP agent in direct communication with the request sender). Regardless of scope of the request, the Public header MUST always be included in the OPTIONS response listing the methods that are supported by the responding RTSP agent. In addition, if the scope of the request is limited to a media resource, the Allow header MUST be included in the response to enumerate the set of methods that are allowed for that resource unless the set of methods completely matches the set in the Public header. If the given resource is not available, the RTSP agent SHOULD return an appropriate response code such as 3rr or 4xx. The Supported header MAY be included in the request to query the set of features that are supported by the Schulzrinne, et al. Expires May 7, 2009 [Page 57] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 responding RTSP agent. The OPTIONS method can be used to keep an RTSP session alive. However, it is not the preferred means of session keep-alive signalling, see Section 16.48. An OPTIONS request intended for keeping alive an RTSP session MUST include the Session header with the associated session ID. Such a request SHOULD also use the media or the aggregated control URI as the Request-URI. Example: C->S: OPTIONS * RTSP/2.0 CSeq: 1 User-Agent: PhonyClient/1.2 Require: Proxy-Require: gzipped-messages Supported: play.basic S->C: RTSP/2.0 200 OK CSeq: 1 Public: DESCRIBE, SETUP, TEARDOWN, PLAY, PAUSE Supported: play.basic, implicit-play, gzipped-messages Server: PhonyServer/1.1 Note that some of the feature-tags in Require and Proxy-Require are fictional features. 13.2. DESCRIBE The DESCRIBE method is used to retrieve the description of a presentation or media object from a server. The Request-URI of the DESCRIBE request identifies the media resource of interest. The client MAY include the Accept header in the request to list the description formats that it understands. The server SHALL respond with a description of the requested resource and return the description in the entity of the response. The DESCRIBE reply- response pair constitutes the media initialization phase of RTSP. Example: Schulzrinne, et al. Expires May 7, 2009 [Page 58] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: DESCRIBE rtsp://server.example.com/fizzle/foo RTSP/2.0 CSeq: 312 User-Agent: PhonyClient 1.2 Accept: application/sdp, application/example S->C: RTSP/2.0 200 OK CSeq: 312 Date: Thu, 23 Jan 1997 15:35:06 GMT Server: PhonyServer 1.1 Content-Base: rtsp://server.example.com/fizzle/foo/ Content-Type: application/sdp Content-Length: 358 v=0 o=mhandley 2890844526 2890842807 IN IP4 192.0.2.46 s=SDP Seminar i=A Seminar on the session description protocol u=http://www.example.com/lectures/sdp.ps e=seminar@example.com (Seminar Management) c=IN IP4 0.0.0.0 a=recvonly a=control:* t=2873397496 2873404696 m=audio 3456 RTP/AVP 0 a=control:audio m=video 2232 RTP/AVP 31 a=control:video The DESCRIBE response SHOULD contain all media initialization information for the resource(s) that it describes. Servers SHOULD NOT use the DESCRIBE response as a means of media indirection by having the description point at another server, instead usage of 3rr responses are recommended. By forcing a DESCRIBE response to contain all media initialization for the set of streams that it describes, and discouraging the use of DESCRIBE for media indirection, any looping problems can be avoided that might have resulted from other approaches. Media initialization is a requirement for any RTSP-based system, but the RTSP specification does not dictate that this is required to be done via the DESCRIBE method. There are three ways that an RTSP client may receive initialization information: o via an RTSP DESCRIBE request o via some other protocol (HTTP, email attachment, etc.) Schulzrinne, et al. Expires May 7, 2009 [Page 59] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o via some form of a user interface If a client obtains a valid description from an alternate source, the client MAY use this description for initialization purposes without issuing a DESCRIBE request for the same media. It is RECOMMENDED that minimal servers support the DESCRIBE method, and highly recommended that minimal clients support the ability to act as "helper applications" that accept a media initialization file from a user interface, and/or other means that are appropriate to the operating environment of the clients. 13.3. SETUP The SETUP request for an URI specifies the transport mechanism to be used for the streamed media. The SETUP method may be used in two different cases; Create an RTSP session and change the transport parameters of already set up media stream. SETUP can be used in all three states; INIT, and READY, for both purposes and in PLAY to change the transport parameters. There is also a third possibile usage for the SETUP method which is not specified in this memo: adding a media to a session. Using SETUP to add media to an existing session, when the session is in PLAY state, is unspecified. The Transport header, see Section 16.51, specifies the transport parameters acceptable to the client for data transmission; the response will contain the transport parameters selected by the server. This allows the client to enumerate in descending order of preference the transport mechanisms and parameters acceptable to it, while the server can select the most appropriate. It is expected that the session description format used will enable the client to select a limited number possible configurations that are offered to the server to choose from. All transport related parameters shall be included in the Transport header, the use of other headers for this purpose is discouraged due to middleboxes, such as firewalls or NATs. For the benefit of any intervening firewalls, a client SHALL indicate the known transport parameters, even if it has no influence over these parameters, for example, where the server advertises a fixed multicast address as destination. Since SETUP includes all transport initialization information, firewalls and other intermediate network devices (which need this information) are spared the more arduous task of parsing the DESCRIBE response, which has been reserved for media initialization. The client SHALL include the Accept-Ranges header in the request Schulzrinne, et al. Expires May 7, 2009 [Page 60] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 indicating all supported unit formats in the Range header. This allows the server to know which format it may use in future session related responses, such as PLAY response without any range in the request. If the client does not support a time format necessary for the presentation the server SHALL respond using 456 (Header Field Not Valid for Resource) and include the Accept-Ranges header with the range unit formats supported for the resource. In a SETUP response the server SHALL include the Accept-Ranges header (see Section 16.5) to indicate which time formats that are acceptable to use for this media resource. The SETUP response 200 OK SHALL include the Media-Properties header (see Section 16.29 ). The combination of the parameters of the Media-Properties header indicate the nature of the content present in the session (see also Section 1.5). For example, a live stream with time shifting is indicated by o Random Access set to Random-Access, o Content Modifications set to Time Progressing, o Retention set to Time-Duration (with specific recording window time value). The SETUP response 200 OK SHALL include the Media-Range header (see Section 16.30) if the media is Time-Progressing. A basic example for SETUP: C->S: SETUP rtsp://example.com/foo/bar/baz.rm RTSP/2.0 CSeq: 302 Transport: RTP/AVP;unicast;dest_addr=":4588"/":4589", RTP/AVP/TCP;unicast;interleaved=0-1 Accept-Ranges: NPT, UTC User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 302 Date: Thu, 23 Jan 1997 15:35:06 GMT Server: PhonyServer 1.1 Session: 47112344;timeout=60 Transport: RTP/AVP;unicast;dest_addr="192.0.2.53:4588"/ "192.0.2.53:4589"; src_addr="192.0.2.241:6256"/ "192.0.2.241:6257"; ssrc=2A3F93ED Accept-Ranges: NPT Media-Properties: Random-Access=3.2, Time-Progressing, Time-Duration=3600.0 Schulzrinne, et al. Expires May 7, 2009 [Page 61] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Media-Range: npt=0-2893.23 In the above example the client wants to create an RTSP session containing the media resource "rtsp://example.com/foo/bar/baz.rm". The transport parameters acceptable to the client is either RTP/AVP/ UDP (UDP per default) to be received on client port 4588 and 4589 or RTP/AVP interleaved on the RTSP control channel. The server selects the RTP/AVP/UDP transport and adds the ports it will send and received RTP and RTCP from, and the RTP SSRC that will be used by the server. The server MUST generate a session identifier in response to a successful SETUP request, unless a SETUP request to a server includes a session identifier, in which case the server MUST bundle this setup request into the existing session (aggregated session) or return error 459 (Aggregate Operation Not Allowed) (see Section 15.4.11). An Aggregate control URI MUST be used to control an aggregated session. This URI MUST be different from the stream control URIs of the individual media streams included in the aggregate. The Aggregate control URI is to be specified by the session description if the server supports aggregated control and aggregated control is desired for the session. However even if aggregated control is offered the client MAY chose to not set up the session in aggregated control. If an Aggregate control URI is not specified in the session description, it is normally an indication that non-aggregated control should be used. The SETUP of media streams in an aggregate which has not been given an aggregated control URI is unspecified. While the session ID sometimes has enough information for aggregate control of a session, the Aggregate control URI is still important for some methods such as SET_PARAMETER where the control URI enables the resource in question to be easily identified. The Aggregate control URI is also useful for proxies, enabling them to route the request to the appropriate server, and for logging, where it is useful to note the actual resource that a request was operating on. A session will exist until it is either removed by a TEARDOWN request or is timed-out by the server. The server MAY remove a session that has not demonstrated liveness signs from the client(s) within a certain timeout period. The default timeout value is 60 seconds; the server MAY set this to a different value and indicate so in the timeout field of the Session header in the SETUP response. For further discussion see Section 16.48. Signs of liveness for an RTSP session are: o Any RTSP request from a client(s) which includes a Session header with that session's ID. Schulzrinne, et al. Expires May 7, 2009 [Page 62] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o If RTP is used as a transport for the underlying media streams, an RTCP sender or receiver report from the client(s) for any of the media streams in that RTSP session. RTCP Sender Reports may for example be received in sessions where the server is invited into a conference session and is as valid for keep-alive. If a SETUP request on a session fails for any reason, the session state, as well as transport and other parameters for associated streams SHALL remain unchanged from their values as if the SETUP request had never been received by the server. 13.3.1. Changing Transport Parameters A client MAY issue a SETUP request for a stream that is already set up or playing in the session to change transport parameters, which a server MAY allow. If it does not allow changing of parameters, it MUST respond with error 455 (Method Not Valid In This State). Reasons to support changing transport parameters, is to allow for application layer mobility and flexibility to utilize the best available transport as it becomes available. If a client receives a 455 when trying to change transport parameters while the server is in play state, it MAY try to put the server in ready state using PAUSE, before issuing the SETUP request again. If also that fails the changing of transport parameters will require that the client performs a TEARDOWN of the affected media and then setting it up again. In aggregated session avoiding tearing down all the media at the same time will avoid the creation of a new session. All transport parameters MAY be changed. However the primary usage expected is to either change transport protocol completely, like switching from Interleaved TCP mode to UDP or vise versa or change delivery address. In a SETUP response for a request to change the transport parameters while in Play state, the server SHALL include the Range to indicate from what point the new transport parameters are used. Further, if RTP is used for delivery, the server SHALL also include the RTP-Info header to indicate from what timestamp and RTP sequence number the change has taken place. If both RTP-Info and Range is included in the response the "rtp_time" parameter and range MUST be for the corresponding time, i.e. be used in the same way as for PLAY to ensure the correct synchronization information is available. If the transport parameters change while in PLAY state results in a change of synchronization related information, for example changing RTP SSRC, the server MUST provide in the SETUP response the necessary synchronization information. However the server is RECOMMENDED to avoid changing the synchronization information if possible. Schulzrinne, et al. Expires May 7, 2009 [Page 63] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 13.4. PLAY This section describes the usage of the PLAY method in general, for aggregated sessions, and in different usage scenarios. 13.4.1. General Usage The PLAY method tells the server to start sending data via the mechanism specified in SETUP and which part of the media should be played out. PLAY requests are valid when the session is in READY or PLAY states. A PLAY request MUST include a Session header to indicate which session the request applies to. Upon receipt of the PLAY request, the server SHALL position the normal play time to the beginning of the range specified in the received Range header and delivers stream data until the end of the range if given, or until a new PLAY request is received, else to the end of the media is reached. To allow for precise composition multiple ranges MAY be specified in one PLAY Request. The range values are valid if all given ranges are part of any media within the aggregate. If a given range value points outside of the media, the response SHALL be the 457 (Invalid Range) error code. The below example will first play seconds 10 through 15, then, immediately following, seconds 20 to 25, and finally seconds 30 through the end. C->S: PLAY rtsp://audio.example.com/audio RTSP/2.0 CSeq: 835 Session: 12345678 Range: npt=10-15, npt=20-25, npt=30- Seek-Style: RAP User-Agent: PhonyClient/1.2 See the description of the PAUSE request for further examples. A PLAY request without a Range header is legal. It SHALL start playing a stream from the beginning (npt=0-) unless the stream has been paused or is currently playing. If a stream has been paused via PAUSE, stream delivery resumes at the pause point. If a stream is currently playing, the new PLAY begins at the current stream position. The stream SHALL play until the end of the media. The Range header MUST NOT contain a time parameter. The usage of time in PLAY method has been deprecated. If a request with time parameter is received the server SHOULD respond with a 457 (Invalid Range) to indicate that the time parameter is not supported. If no range is specified in the request, the start position SHALL still be returned in the reply. If the medias that are part of an aggregate has Schulzrinne, et al. Expires May 7, 2009 [Page 64] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 different lengths, the PLAY request SHALL be performed as long as the given range is valid for any media, for example the longest media. Media will be sent whenever it is available for the given play-out point. A client desiring to play the media from the beginning MUST send a PLAY request with a Range header pointing at the beginning, e.g. npt=0-. If a PLAY request is received without a Range header when media delivery has stopped at the end, the server SHOULD respond with a 457 "Invalid Range" error response. In that response the current pause point in a Range header SHALL be included. All range specifiers in this specification allow for ranges with unspecified begin times (e.g. "npt=-30"). When used in a PLAY request, the server treats this as a request to start/resume playback from the current pause point, ending at the end time specified in the Range header. If the pause point is located later than the given end value, a 457 (Invalid Range) response SHALL be given. Server MUST include a "Range" header in any PLAY response. The response MUST use the same format as the request's range header contained. If no Range header was in the request, the format used in any previous PLAY request within the session SHOULD be used. If no format has been indicated in a previous request the server MAY use any time format supported by the media and indicated in the Accept- Ranges header in the SETUP respone. It is RECOMMENDED that NPT is used if supported by the media. For any error response to a PLAY request, the server's response depends on the current session state. If the session is in ready state, the current pause-point is returned. For time-progressing content where the pause-point moves with real-time due to limited retention, the current resume point is returned. For sessions in playing state, the current playout point and the remaining parts of the range request is returned. A PLAY response MAY include a header(s) carrying synchronization information. As the information necessary is dependent on the media transport format, further rules specifying the header and its usage is needed. For RTP the RTP-Info header is specified, see Section 16.43, and used in the following example. Here is a simple example for a single audio stream where the client requests the media starting from 3.52 seconds and to the end. The server sends a 200 OK response with the actual play time (equal to the requested in this case) and the RTP-Info header that contains the necessary parameters for the RTP stack. Schulzrinne, et al. Expires May 7, 2009 [Page 65] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: PLAY rtsp://example.com/audio RTSP/2.0 CSeq: 836 Session: 12345678 Range: npt=3.52- User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 836 Date: Thu, 23 Jan 1997 15:35:06 GMT Server: PhonyServer 1.0 Range: npt=3.52-324.39 RTP-Info:url="rtsp://example.com/audio" ssrc=0D12F123:seq=14783;rtptime=2345962545 S->C: RTP Packet TS=2345962545 => NPT=3.52 Duration=4.15 seconds For media with random-acces properties, the server MUST reply with the actual range that will be played back, i.e. for which duration any media (having content at this time) is delivered. This may differ from the requested range if alignment of the requested range to valid frame boundaries is required for the media source. Note that some media streams in an aggregate may need to be delivered from even earlier points. Also, some media format have a very long duration per individual data unit, therefore it might be necessary for the client to parse the data unit, and select where to start. The client can express its desired handling by the server by including the Seek-Style header (Section 16.45) in the PLAY request, if desired. In the following example the client receives the first media packet that stretches all the way up and past the requested playtime. Thus, it is the client's decision if to render to the user the time between 3.52 and 7.05, or to skip it. In most cases it is probably most suitable to not render that time period. Schulzrinne, et al. Expires May 7, 2009 [Page 66] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: PLAY rtsp://example.com/audio RTSP/2.0 CSeq: 836 Session: 12345678 Range: npt=7.05- User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 836 Date: Thu, 23 Jan 1997 15:35:06 GMT Server: PhonyServer 1.0 Range: npt=3.52- RTP-Info:url="rtsp://example.com/audio" ssrc=0D12F123:seq=14783;rtptime=2345962545 S->C: RTP Packet TS=2345962545 => NPT=3.52 Duration=4.15 seconds After playing the desired range, the presentation does NOT transition to the READY state, media delivery simply stops. A PAUSE request MUST be issued before the stream enters the READY state. A PLAY request while the stream is still in the PLAYING state is legal, and can be issued without an intervening PAUSE request. Such a request SHALL replace the current PLAY action with the new one requested, i.e. being handle the same as the request was received in ready state. In the case the first time range in Range header has a open start time (-endtime), the server SHALL continue to play from where it currently was until the specified end point. This is useful to change ongoing playback to play another sequence, or end at another point than in the previous request. The following example plays the whole presentation starting at SMPTE time code 0:10:20 until the end of the clip. Note: The RTP-Info headers has been broken into several lines to fit the page. C->S: PLAY rtsp://audio.example.com/twister.en RTSP/2.0 CSeq: 833 Session: 12345678 Range: smpte=0:10:20- User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 833 Date: Thu, 23 Jan 1997 15:35:06 GMT Server: PhonyServer 1.0 Range: smpte=0:10:22-0:15:45 RTP-Info:url="rtsp://example.com/twister.en" ssrc=0D12F123:seq=14783;rtptime=2345962545 For playing back a recording of a live presentation, it may be Schulzrinne, et al. Expires May 7, 2009 [Page 67] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 desirable to use clock units: C->S: PLAY rtsp://audio.example.com/meeting.en RTSP/2.0 CSeq: 835 Session: 12345678 Range: clock=19961108T142300Z-19961108T143520Z User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 835 Date: Thu, 23 Jan 1997 15:35:06 GMT Server:PhonyServer 1.0 Range: clock=19961108T142300Z-19961108T143520Z RTP-Info:url="rtsp://example.com/meeting.en" ssrc=0D12F123:seq=53745;rtptime=484589019 13.4.2. Aggregated Sessions PLAY requests can operate on sessions controlling a single media and on aggregated sessions controlling multiple media. In an aggregated session the PLAY request MUST contain an aggregated control URI. A server SHALL responde with error 460 (Only Aggregate Operation Allowed) if the client PLAY Request-URI is for one of the media. The media in an aggregate SHALL be played in sync. If a client wants individual control of the media it needs to use separate RTSP sessions for each media. For aggregated sessions where the initial SETUP request (creating a session) is followed by one or more additional SETUP request, a PLAY request MAY be pipelined after those additional SETUP requests without awaiting their responses. This procedure can reduce the delay from start of session establishment until media play-out has started with one round trip time. However an client needs to be aware that using this procedure will result in the playout of the server state established at the time of processing the PLAY, i.e., after the processing of all the requests prior to the PLAY request in the pipeline. This may not be the intended one due to failure of any of the prior requests. However a client easily determine this based on the responses from those requests. In case of failure the client can halt the media playout using PAUSE and try to establish the intended state again before issuing another PLAY request. 13.4.3. Updating current PLAY Requests Clients can issue PLAY request while the stream is In PLAYING state and thus updating their request. The possibility to replace a current PLAY request with a new one replaces the following RTSP 1.0 functions based on PLAY in play state: Schulzrinne, et al. Expires May 7, 2009 [Page 68] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o The queued play functionality described in RFC 2326 [RFC2326] is removed and multiple ranges can be used to achieve a similar functionality in combination with the possibility to replace previous play messages. o The use of PLAY for keep-alive signaling, i.e. PLAY request without a range header in PLAY state, has also been deprecated. Instead a client can use, SET_PARAMETER (recommended) or OPTIONS (allowed) for keep alive. The important difference compared to a PLAY request in ready state is the handling of the current playpoint and how the range header in request is constructed. The session is actively playing media and the playpoint will be moving making the exact time a request will take action is hard to predict. Depending on how the PLAY header appears two different cases exist: total replacement or continuation. A total replacement is signalled by having the first range specification have an explicit start value, e.g. npt=45- or npt=45-60, in which case the server stops playout at the current playout point and then starts delivering media according to the Range header. This is equivalent to having the client first send a PAUSE and then a new play request that isn't based on the pause point. In the case of continuation the first range specifier has an open start point and a explict stop value (Z), e.g. npt=-60, which indicate that it SHALL convert the range specifier being played prior to this PLAY request (X to Y) into (X to Z) and continue as this was the request originally played. For both total replacement and continuation the PLAY request SHALL remove any additional range specifiers present in the previous request and add any that is present in the new PLAY request. An example of this behavior. The server has received requests to play ranges 10 to 15 and then 13 to 20 (that is, overlapping ranges). If the new PLAY request arrives at the server 4 seconds after the previous one, it will take effect while the server plays the first range (10-15). Thus changing the behavior of this range to continue to play to 25 seconds, i.e. the equivalent single request would be PLAY with range: npt=10-25. Note that the second range (13-20) is deleted and never comes into effect. If the new PLAY request would arrive as the second range in the first request was playing (13-20 and shown below), then the equivalent single request would be play with range:npt=10-15,npt=13-25. Schulzrinne, et al. Expires May 7, 2009 [Page 69] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: PLAY rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 834 Session: 12345678 Range: npt=10-15, npt=13-20 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 834 Date: Thu, 23 Jan 1997 15:35:06 GMT Server: PhonyServer 1.0 Range: npt=10-15, npt=13-20 RTP-Info:url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=5712;rtptime=934207921, url="rtsp://example.com/fizzle/videotrack" ssrc=789DAF12:seq=57654;rtptime=2792482193 Session: 12345678 C->S: PLAY rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 835 Session: 12345678 Range: npt=-25 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 835 Date: Thu, 23 Jan 1997 15:35:09 GMT Server: PhonyServer 1.0 Range: npt=14-25 RTP-Info:url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=5712;rtptime=934239921, url="rtsp://example.com/fizzle/videotrack" ssrc=789DAF12:seq=57654;rtptime=2792842193 Session: 12345678 13.4.4. Playing On-Demand Media On-demand media is indicated by the content of the Media-Properties header in the SETUP response by (see also Section 16.29): o Random-Access property is set to Random Acces; o Content Modifications set to unmutable; o Retetion set Unlimited or Time-Limited. Playing on-demand media follows the general usage as described in Section 13.4.1. Schulzrinne, et al. Expires May 7, 2009 [Page 70] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 13.4.5. Playing Dynamic On-Demand Media Dynamic on-demand media is indicated by the content of the Media- Properties header in the SETUP response by (see also Section 16.29): o Random-Access set to Random Access; o Content Modifications set to dynamic; o Retetion set unlimited or Time-Limited. Playing on-demand media follows the general usage as described in Section 13.4.1 as long as the media has not been changed. There are ways for the client to get informed about changed of media resources in play state, if the resource was changed. The client will receive a PLAY_NOTIFY request with Notify-Reason header set to media-properties-update (see Section 13.5.2. The client can use the value of the Media-Range to decide further actions, if the Media- Range header is present in the PLAY_NOTIFY request. The second way is that the client issues a GET_PARAMETER request without a body but including a Media-Range header. The 200 OK response SHALL include the current Media-Range header (see Section 16.30). 13.4.6. Playing Live Media Live media is indicated by the content of the Media-Properties header in the SETUP response by (see also Section 16.29): o Random-Access set to no-seeking; o Content Modifications set to Time-Progressing; o Retetion with Time-Duration set to 0.0. For live media, the SETUP response 200 OK SHALL include the Media- Range header (see Section 16.30). A client MAY send PLAY requests without the Range header, if the request include the Range header it SHALL use a symbolic value representing "now". For NPT that range specification is "npt=now-". The server SHALL include the Range header in the response and it MUST indicate a explict time value and not a symbolic value. In other words npt=now- is not a valid to use in the respone. Instead the time since session start is recommended expressed as an open interval, e.g. "npt=96.23-". An absolute time value (clock) for the corresponding time MAY be given, i.e. "clock=20030213T143205Z-". The UTC clock format SHOULD only be used if client has shown support for Schulzrinne, et al. Expires May 7, 2009 [Page 71] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 it. 13.4.7. Playing Live with Recording Certain media server may offer recording services of live sessions to their clients. This recording would normally be from the begining of the media session. Clients can randomly access the media between now and the begining of the media session. This live media with recording is indicated by the content of the Media-Properties header in the SETUP response by (see also Section 16.29): o Random-Access set to random-access; o Content Modifications set to Time-Progressing; o Retetion set to Time-limited or Unlimited The SETUP response 200 OK SHALL include the Media-Range header (see Section 16.30) for this type of media. For live media with recording the Range header indicates the current playback time in the media and the Media Range indicates the currently available media window around the current time. This window can cover recorded content in the past (seen from current time in the media) or recorded content in the future (seen from current time in the media). The server adjusts the play point to the requested border of the window, if the client requests a play point that is located outside the recording windows, e.g., if requested to far in the past, the server selects the oldest range in the recording. The considerations in Section 13.5.3 apply, if a client requests playback at Scale (Section 16.44) values other than 1.0 (Normal playback rate) while playing live media with recording. 13.4.8. Playing Live with Time-Shift Certain media server may offer time-shift services to their clients. This time shift records a fixed interval in the past, i.e., a sliding window recording mechanism, but not past this interval. Clients can randomly access the media between now and the interval. This live media with recording is indicated by the content of the Media- Properties header in the SETUP response by (see also Section 16.29): o Random-Access set to random-access; o Content Modifications set to Time-Progressing; o Retetion set to Time-Duration and a value indicating the recording interval (>0). Schulzrinne, et al. Expires May 7, 2009 [Page 72] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The SETUP response 200 OK SHALL include the Media-Range header (see Section 16.30) for this type of media. For live media with recording the Range header indicates the current time in the media and the Media Range indicates a window around the current time. This window can cover recorded content in the past (seen from current time in the media) or recorded content in the future (seen from current time in the media). The server adjusts the play point to the requested border of the window, if the client requests a play point that is located outside the recording windows, e.g., if requested to far in the past, the server selects the oldest range in the recording. The considerations in Section 13.5.3 apply, if a client requests playback at Scale (Section 16.44) values other than 1.0 (Normal playback rate) while playing live media with time-shift. 13.5. PLAY_NOTIFY The PLAY_NOTIFY method is issued by a server to inform a client about an ansynchronous event for a session in play state. The Session header MUST be presented in a PLAY_NOTIFY request and indicates the scope of the request. Sending of PLAY_NOTIFY requests requires a persistent connection between server and client, otherwise there is no way for the server to send this request method to the client. PLAY_NOTIFY requests have an end-to-end (i.e. server to client) scope, as they carry the Session header, and apply only to the given session. The client SHOULD immediately return a response to the server. PLAY_NOTIFY requests MAY be used with a message body, depending on the value of the Notify-Reason header. It is described in the particular section for each Notify-Reason if a message body is used. However, currently there is no Notify-Reason that allows using a message body. There is the need to obey some limitations, when adding new Notify-Reasons that intend to use a message body: The server can send any type of message body, but it is not ensured that the client can understand the received message body. This is related to DESCRIBE (seeSection 13.2 ), but there the client can state its acceptable message bodies by using the Accept header. In case of PLAY_NOTIFY, the server does not know which message bodies are understood by the client. The Notify-Reason header (see Section 16.31) specifies the reason why the server sends the PLAY_NOTIFY request. This is extensible and new reasons MAY be added in the future. In case the client does not understand the reason for the notification it SHALL respond with an 465 (Notification Reason Unknown) (Section 15.4.17) error code. Servers can send PLAY_NOTIFY with these types: Schulzrinne, et al. Expires May 7, 2009 [Page 73] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o end-of-stream (see Section 13.5.1); o media-properties-update (see Section 13.5.2); o and scale-change (see Section 13.5.3). 13.5.1. End-of-Stream A PLAY_NOTIFY request with Notify-Reason header set to end-of-stream indicates the end of the media streams has been reached or will be in the near future for the given session aggregate. The request SHALL NOT be issued unless the server is in the playing state. The end of the media stream delivery notification may be for either succesful completion of the PLAY request currently being served or indicate some error resulting in failure to complete the request. The Request-Status header (Section 16.41) SHALL be included to indicate which request the notification is for and its completion status. The message response status codes (Section 8.1.1) are used to indicate how the PLAY request concluded. In case a PLAY_NOTIFY was issues prior to the actual completion and some error occured resulting in that the previosuly sent was in error a new Notification MUST be sent including the correct status for the completion and all additional information. PLAY_NOTIFY requests with Notify-Reason header set to end-of-stream MUST include a Range header. The Range header indicates the point in the stream or streams where delivery was/are ending with the timescale that has been used by the client in the PLAY request being fulfilled. For normal play time it is not alllowed to use "now" as server do know the real ending time of the media stream and now carries no information to determine what has/will be delivered. When end-of-stream notifications are issued prior to having sent the last media packets, this is evident as the end time in the Range header is beyond the current time in the media being received by the client, e.g., npt=-15, if npt is currently at 14.2 seconds. If RTP is used as media transport, a RTP-Info header MUST be included, and the RTP-Info header MUST indicate the last sequence number in the seq parameter. A PLAY_NOTIFY request with Notify-Reason header set to end-of-stream MUST NOT carry a message body. This example request notifies the client about a future end-of-stream event: Schulzrinne, et al. Expires May 7, 2009 [Page 74] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 S->C: PLAY_NOTIFY rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 854 Notify-Reason: end-of-stream Request-Status: cseq=853 status=200 reason="OK" Range: npt=-145 RTP-Info:url="rtsp://example.com/audio" ssrc=0D12F123:seq=14783;rtptime=2345962545 Session: uZ3ci0K+Ld-M C->S: RTSP/2.0 200 OK CSeq: 854 User-Agent: PhonyClient/1.2 13.5.2. Media-Properties-Update A PLAY_NOTIFY request with Notify-Reason header set to media- properties-update indicates an update of the media properties for the given session (see Section 16.29) and/or the available media range that can be played as indicated by Media-Range (Section 16.30). PLAY_NOTIFY requests with Notify-Reason header set to media- properties-update MUST include a Media-Properties and Date header and SHOULD include a Media-Range header. This notification SHALL be sent for media that are time-progressing every time a event happens that changes the basis for making estimations on how the media range progress. In addition it is RECOMMENDED that the server sends these notification every 5 minutes for time-progressing content to ensure the long term stability of the client estimation and allowing for clock skew detection by the client. Requests for the just mentioned reasons SHALL include Media- Range header to provide current Media duration and the Range header to indicate the current playing point and any remaining parts of the requsted range. A PLAY_NOTIFY request with Notify-Reason header set to media- properties-update MUST NOT carry a message body. Schulzrinne, et al. Expires May 7, 2009 [Page 75] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 S->C: PLAY_NOTIFY rtsp://example.com/fizzle/foo RTSP/2.0 Date: Tue, 14 Apr 2008 15:48:06 GMT CSeq: 854 Notify-Reason: media-properties-update Session: uZ3ci0K+Ld-M Media-Properties: Time-Progressing, Time-Limited=20080415T153919.36Z, Random-Access=5.0 Media-Range: npt=0-1:37:21.394 Range: npt=1:15:49.873- C->S: RTSP/2.0 200 OK CSeq: 854 User-Agent: PhonyClient/1.2 13.5.3. Scale-Change When a client request playback at Scale (Section 16.44) values other than 1.0 (Normal playback rate) then the server may be forced to changed the rate. For time progressing media with some retention, i.e. the server stores already sent content, a client requesting to play with Scale values larger than 1 may catch up with front end of the media. The server will be unable to continue provide content at Scale larger than 1 as content only made available by the server at Scale=1. Another case is when Scale < 1 and the media retention is time_duration limited. In this case the playback point can reach the the oldest media unit available, and further playback at this scale becomes impossible as there will be no media available. To avoid having the client loose any media, the scale will need to be adjusted to the same rate which the media is removed from the storage buffer, commonly scale=1.0. To minimize impact on playback in any of the above cases the server SHALL modify the playback properties and set Scale to a supportable value (commonly 1.0) and continue delivery the media. When doing this modification it MUST send a PLAY_NOTIFY message with the Notify- Reason header set to "Scale-Change". The request SHALL contain a Range header with the media time where the change took effect, a Scale header with the new value in use, Session header with the ID for the session it applies to and a Date header with the server wall clock time of the change. For time progressing content also the Media-Range and the Media-Properties at this point in time SHALL be included. For media streams being delivered using RTP also a RTP-Info header SHALL be included. It MUST contain the rtptime parameter with a value corresponding to the point of change in that media and optionally the sequence number. Schulzrinne, et al. Expires May 7, 2009 [Page 76] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 A PLAY_NOTIFY request with Notify-Reason header set to "Scale-Change" MUST NOT carry a message body. S->C: PLAY_NOTIFY rtsp://example.com/fizzle/foo RTSP/2.0 Date: Tue, 14 Apr 2008 15:48:06 GMT CSeq: 854 Notify-Reason: scale-change Session: uZ3ci0K+Ld-M Media-Properties: Time-Progressing, Time-Limited=20080415T153919.36Z, Random-Access=5.0 Media-Range: npt=0-1:37:21.394 Range: npt=1:37:21.394- Scale: 1 RTP-Info: url="rtsp://example.com/fizzle/foo/audio" ssrc=0D12F123:rtptime=2345962545 C->S: RTSP/2.0 200 OK CSeq: 854 User-Agent: PhonyClient/1.2 13.6. PAUSE The PAUSE request causes the stream delivery to immediately be interrupted (halted). A PAUSE request MUST be done either with the aggregated control URI for aggregated sessions, resulting in all media being halted, or the media URI for non-aggregated sessions. Any attempt to do muting of a single media with an PAUSE request in an aggregated session SHALL be responded with error 460 (Only Aggregate Operation Allowed). After resuming playback, synchronization of the tracks MUST be maintained. Any server resources are kept, though servers MAY close the session and free resources after being paused for the duration specified with the timeout parameter of the Session header in the SETUP message. Example: C->S: PAUSE rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 834 Session: 12345678 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 834 Date: Thu, 23 Jan 1997 15:35:06 GMT Range: npt=45.76- The PAUSE request causes stream delivery to be interrupted immediately on receipt of the message and the pause point is set to Schulzrinne, et al. Expires May 7, 2009 [Page 77] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 the current point in the presentation. That pause point in the media stream needs to be maintained. A subsequent PLAY request without Range header SHALL resume from the pause point and play until media end. The pause point after any PAUSE request SHALL be returned to the client by adding a Range header with what remains unplayed of the PLAY request's ranges, i.e. including all the remaining ranges part of multiple range specification. For media with random access properties If one desires to resume playing a ranged request, one simply includes the Range header from the PAUSE response. Any play- request including symbolic values, such as the NPT timescale's "now" MUST be resolved into the actual stream position where the pause point is. For example a Play request with a range specification of "npt=now-" will need to be responded with an explicit value such as "npt=157.321-". For media that is time-progressing and has retention duration=0 the follow-up PLAY request to start media delivery again, will need to use "npt=now-" and not the answer in the pause-respone. C->S: PLAY rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 834 Session: 12345678 Range: npt=10-30 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 834 Date: Thu, 23 Jan 1997 15:35:06 GMT Server: PhonyServer 1.0 Range: npt=10-30 RTP-Info:url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=5712;rtptime=934207921, url="rtsp://example.com/fizzle/videotrack" ssrc=4FAD8726:seq=57654;rtptime=2792482193 Session: 12345678 After 11 seconds, i.e. at 21 seconds into the presentation: C->S: PAUSE rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 835 Session: 12345678 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 835 Date: 23 Jan 1997 15:35:09 GMT Server: PhonyServer 1.0 Range: npt=21-30 Session: 12345678 Schulzrinne, et al. Expires May 7, 2009 [Page 78] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 If a client issues a PAUSE request and the server acknowledges and enters the READY state, the proper server response, if the player issues another PAUSE, is still 200 OK. The 200 OK response MUST include the Range header with the current pause point. See examples below: C->S: PAUSE rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 834 Session: 12345678 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 834 Session: 12345678 Date: Thu, 23 Jan 1997 15:35:06 GMT Range: npt=45.76-98.36 C->S: PAUSE rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 835 Session: 12345678 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 835 Session: 12345678 Date: 23 Jan 1997 15:35:07 GMT Range: npt=45.76-98.36 13.7. TEARDOWN The TEARDOWN client to server request stops the stream delivery for the given URI, freeing the resources associated with it. A TEARDOWN request MAY be performed on either an aggregated or a media control URI. However some restrictions apply depending on the current state. The TEARDOWN request SHALL contain a Session header indicating what session the request applies to. A TEARDOWN using the aggregated control URI or the media URI in a session under non-aggregated control (single media session) MAY be done in any state (Ready, and Play). A successful request SHALL result in that media delivery is immediately halted and the session state is destroyed. This SHALL be indicated through the lack of a Session header in the response. A TEARDOWN using a media URI in an aggregated session MAY only be done in Ready state. Such a request only removes the indicated media stream and associated resources from the session. This may result in that a session returns to non-aggregated control, due to that it only Schulzrinne, et al. Expires May 7, 2009 [Page 79] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 contains a single media after the requests completion. A session that will exist after the processing of the TEARDOWN request SHALL in the response to that TEARDOWN request contain a Session header. Thus the presence of the Session header indicates to the receiver of the response if the session is still existing or has been removed. Example: C->S: TEARDOWN rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 892 Session: 12345678 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 892 Server: PhonyServer 1.0 13.8. GET_PARAMETER The GET_PARAMETER request retrieves the value of any specified parameter or parameters for a presentation or stream specified in the URI. If the Session header is present in a request, the value of a parameter MUST be retrieved in the specified session context. There exist two ways of specifying the parameters to retrive. The first is by including headers that has been defined such that you can use them for this purpose. Header for this purpose should allow empty, or stripped value parts to avoid having to specify bogus data when indicating the desire to retrive a value. The succesful completion of the request should also be evident from any filled out values in the response. The Media-Range header (Section 16.30) is one such header. The other is to specify a body (entity) that lists the parameter(s) that are desirable to retrieve. The Content-Type header (Section 16.18) is used to specify which format the entity has. The method MAY also be used without a body (entity) or any header that request parameters for keep-alive purpose. Any request that is successful, i.e., a 200 OK response is received, then the keep-alive timer has been updated. Any non-required header present in such a request may or may not been processed. Normaly the presence of filled out values in the header will be indication that the header has been processed. However, for cases when this is difficult to determine, it is recommended to use a feature-tag and the Require header. Due to this reason it is usually easier if any parameters to be retrieved are sent in the body, rather than using any header. Parameters specified within the body of the message must all be understood by the request receiving agent. If one or more parameters are not understood a 451 (Parameter Not Understood) SHALL be sent Schulzrinne, et al. Expires May 7, 2009 [Page 80] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 including a body listing these parameters that wasn't understood. If all parameters are understood their value is filled in and returned in the response message body. Example: S->C: GET_PARAMETER rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 431 Content-Type: text/parameters Session: 12345678 Content-Length: 26 User-Agent: PhonyClient/1.2 packets_received jitter C->S: RTSP/2.0 200 OK CSeq: 431 Content-Length: 38 Content-Type: text/parameters packets_received: 10 jitter: 0.3838 13.9. SET_PARAMETER This method requests to set the value of a parameter or a set of parameters for a presentation or stream specified by the URI. The method MAY also be used without a body (entity). It is the RECOMMENDED method to use in request sent for the sole purpose of updating the keep-alive timer. If this request is successful, i.e. a 200 OK response is received, then the keep-alive timer has been updated. Any non-required header present in such a request may or may not been processed. To allow a client to determine if any such header has been processed, it is necessary to use a feature tag and the Require header. Due to this reason it is RECOMMENDED that any parameters are sent in the body, rather than using any header. A request is RECOMMENDED to only contain a single parameter to allow the client to determine why a particular request failed. If the request contains several parameters, the server MUST only act on the request if all of the parameters can be set successfully. A server MUST allow a parameter to be set repeatedly to the same value, but it MAY disallow changing parameter values. If the receiver of the request does not understand or cannot locate a parameter, error 451 (Parameter Not Understood) SHALL be used. In the case a parameter is not allowed to change, the error code is 458 (Parameter Is Read- Only). The response body SHALL contain only the parameters that have Schulzrinne, et al. Expires May 7, 2009 [Page 81] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 errors. Otherwise no body SHALL be returned. Note: transport parameters for the media stream MUST only be set with the SETUP command. Restricting setting transport parameters to SETUP is for the benefit of firewalls. The parameters are split in a fine-grained fashion so that there can be more meaningful error indications. However, it may make sense to allow the setting of several parameters if an atomic setting is desirable. Imagine device control where the client does not want the camera to pan unless it can also tilt to the right angle at the same time. Example: C->S: SET_PARAMETER rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 421 User-Agent: PhonyClient/1.2 Content-length: 20 Content-type: text/parameters barparam: barstuff S->C: RTSP/2.0 451 Parameter Not Understood CSeq: 421 Content-length: 10 Content-type: text/parameters barparam: barstuff 13.10. REDIRECT The REDIRECT method is issued by a server to inform a client that it required to connect to another server location to access the resource indicated by the Request-URI. The presence of the Session header in a REDIRECT request indicates the scope of the request, and determines the specific semantics of the request. A REDIRECT request with a Session header has end-to-end (i.e. server to client) scope and applies only to the given session. Any intervening proxies SHOULD NOT disconnect the control channel while there are other remaining end-to-end sessions. The OPTIONAL Location header, if included in such a request, SHALL contain a complete absolute URI pointing to the resource to which the client SHOULD reconnect. Specifically, the Location SHALL NOT contain just the host and port. A client may receive a REDIRECT request with a Schulzrinne, et al. Expires May 7, 2009 [Page 82] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Session header, if and only if, an end-to-end session has been established. A client may receive a REDIRECT request without a Session header at any time when it has communication or a connection established with a server. The scope of such a request is limited to the next-hop (i.e. the RTSP agent in direct communication with the server) and applies, as well, to the control connection between the next-hop RTSP agent and the server. A REDIRECT request without a Session header indicates that all sessions and pending requests being managed via the control connection MUST be redirected. The OPTIONAL Location header, if included in such a request, SHOULD contain an absolute URI with only the host address and the OPTIONAL port number of the server to which the RTSP agent SHOULD reconnect. Any intervening proxies SHOULD do all of the following in the order listed: 1. respond to the REDIRECT request 2. disconnect the control channel from the requesting server 3. connect to the server at the given host address 4. pass the REDIRECT request to each applicable client (typically those clients with an active session or an unanswered request) Note: The proxy is responsible for accepting REDIRECT responses from its clients; these responses MUST NOT be passed on to either the original server or the redirected server. The lack of a Location header in any REDIRECT request is indicative of the server no longer being able to fulfill the current request and having no alternatives for the client to continue with its normal operation. It is akin to a server initiated TEARDOWN that applies both to sessions as well as the general connection associated with that client. When the Range header is not included in a REDIRECT request, the client SHOULD perform the redirection immediately and return a response to the server. The server can consider the session as terminated and can free any associated state after it receives the successful (2xx) response. The server MAY close the signalling connection upon receiving the response and the client SHOULD close the signalling connection after sending the 2xx response. The exception to this is when the client has several sessions on the server being managed by the given signalling connection. In this case, the client SHOULD close the connection when it has received and responded to REDIRECT requests for all the sessions managed by the signalling connection. Schulzrinne, et al. Expires May 7, 2009 [Page 83] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 If the OPTIONAL Range header is included in a REDIRECT request, it indicates when the redirection takes effect. The range value MUST be an open ended single value, e.g. npt=59-, indicating the play out time when redirection SHALL occur. Alternatively, a range with a time= parameter indicates the wall clock time by when the redirection MUST take place. When the time= parameter is present in the range, any range value MUST be ignored even though it MUST be syntactically correct. To allow a client to determine that redirect time without being time synchronized with the server, the server SHALL include a Date header in the request. When the indicated redirect point is reached, a client MUST issue a TEARDOWN request and SHOULD close the signalling connection after receiving a 2xx response. The normal connection considerations apply for the server. The differentiation of REDIRECT requests with and without range headers is to allow for clear and explicit state handling. As the state in the server needs to be kept until the point of redirection, the handling becomes more clear if the client is required to TEARDOWN the session at the redirect point. If the REDIRECT request times out following the rules in Section 10.4 the server MAY terminate the session or transport connection that would be redirected by the request. This is a safeguard against misbehaving clients that refuses to respond to a REDIRECT request. That should not provide any benefit. After a REDIRECT request has been processed, a client that wants to continue to send or receive media for the resource identified by the Request-URI will have to establish a new session with the designated host. If the URI given in the Location header is a valid resource URI, a client SHOULD issue a DESCRIBE request for the URI. Note: The media resource indicated by the Location header can be identical, slightly different or totally different. This is the reason why a new DESCRIBE request SHOULD be issued. If the Location header contains only a host address, the client MAY assume that the media on the new server is identical to the media on the old server, i.e. all media configuration information from the old session is still valid except for the host address. However the usage of conditional SETUP using ETag identifiers are RECOMMENDED to verify the assumption. This example request redirects traffic for this session to the new server at the given absolute time: Schulzrinne, et al. Expires May 7, 2009 [Page 84] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 S->C: REDIRECT rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 732 Location: rtsp://s2.example.com:8001 Range: npt=0- ;time=19960213T143205Z Session: uZ3ci0K+Ld-M C->S: RTSP/2.0 200 OK CSeq: 732 User-Agent: PhonyClient/1.2 Schulzrinne, et al. Expires May 7, 2009 [Page 85] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 14. Embedded (Interleaved) Binary Data In order to fulfill certain requirements on the network side, e.g. in conjunction with network address translators that block RTP traffic over UDP, it may be necessary to interleave RTSP messages and media stream data. This interleaving should generally be avoided unless necessary since it complicates client and server operation and imposes additional overhead. Also head of line blocking may cause problems. Interleaved binary data SHOULD only be used if RTSP is carried over TCP. Stream data such as RTP packets is encapsulated by an ASCII dollar sign (24 decimal), followed by a one-byte channel identifier, followed by the length of the encapsulated binary data as a binary, two-byte integer in network byte order. The stream data follows immediately afterwards, without a CRLF, but including the upper-layer protocol headers. Each $ block SHALL contain exactly one upper-layer protocol data unit, e.g., one RTP packet. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | "$" = 24 | Channel ID | Length in bytes | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : Length number of bytes of binary data : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The channel identifier is defined in the Transport header with the interleaved parameter (Section 16.51). When the transport choice is RTP, RTCP messages are also interleaved by the server over the TCP connection. The usage of RTCP messages is indicated by including a range containing a second channel in the interleaved parameter of the Transport header, see Section 16.51. If RTCP is used, packets SHALL be sent on the first available channel higher than the RTP channel. The channels are bi-directional and therefore RTCP traffic are sent on the second channel in both directions. RTCP is sometime needed for synchronization when two or more streams are interleaved in such a fashion. Also, this provides a convenient way to tunnel RTP/RTCP packets through the TCP control connection when required by the network configuration and transfer them onto UDP when possible. Schulzrinne, et al. Expires May 7, 2009 [Page 86] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: SETUP rtsp://example.com/bar.file RTSP/2.0 CSeq: 2 Transport: RTP/AVP/TCP;unicast;interleaved=0-1 Accept-Ranges: NPT, SMPTE, UTC User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 2 Date: Thu, 05 Jun 1997 18:57:18 GMT Transport: RTP/AVP/TCP;unicast;interleaved=5-6 Session: 12345678 Accept-Ranges: NPT C->S: PLAY rtsp://example.com/bar.file RTSP/2.0 CSeq: 3 Session: 12345678 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 3 Session: 12345678 Date: Thu, 05 Jun 1997 18:59:15 GMT RTP-Info: url="rtsp://example.com/bar.file" ssrc=0D12F123:seq=232433;rtptime=972948234 Range: npt=0-56.8 S->C: $005{2 byte length}{"length" bytes data, w/RTP header} S->C: $005{2 byte length}{"length" bytes data, w/RTP header} S->C: $006{2 byte length}{"length" bytes RTCP packet} Schulzrinne, et al. Expires May 7, 2009 [Page 87] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 15. Status Code Definitions Where applicable, HTTP status [H10] codes are reused. Status codes that have the same meaning are not repeated here. See Table 4 for a listing of which status codes may be returned by which requests. All error messages, 4xx and 5xx MAY return a body containing further information about the error. 15.1. Success 1xx 15.1.1. 100 Continue See, [H10.1.1]. 15.2. Success 2xx 15.2.1. 200 OK See, [H10.2.1]. 15.3. Redirection 3xx The notation "3rr" indicates response codes from 300 to 399 inclusive which are meant for redirection. The response code 304 is excluded from this set, as it is not used for redirection. See [H10.3] for definition of status code 300 to 305. However comments are given for some to how they apply to RTSP. Within RTSP, redirection may be used for load balancing or redirecting stream requests to a server topologically closer to the client. Mechanisms to determine topological proximity are beyond the scope of this specification. A 3rr code MAY be used to respond to any request. It is RECOMMENDED that they are used if necessary before a session is established, i.e. in response to DESCRIBE or SETUP. However in cases where a server is not able to send a REDIRECT request to the client, the server MAY need to resort to using 3rr responses to inform a client with a established session about the need for redirecting the session. If an 3rr response is received for an request in relation to a established session, the client SHOULD send a TEARDOWN request for the session, and MAY reestablish the session using the resource indicated by the Location. If the the Location header is used in a response it SHALL contain an absolute URI pointing out the media resource the client is redirected to, the URI SHALL NOT only contain the host name. Schulzrinne, et al. Expires May 7, 2009 [Page 88] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 15.3.1. 300 Multiple Choices See [H10.3.1]. 15.3.2. 301 Moved Permanently The request resource are moved permanently and resides now at the URI given by the location header. The user client SHOULD redirect automatically to the given URI. This response MUST NOT contain a message-body. The Location header MUST be included in the response. 15.3.3. 302 Found The requested resource resides temporarily at the URI given by the Location header. The Location header MUST be included in the response. This response is intended to be used for many types of temporary redirects; e.g., load balancing. It is RECOMMENDED that the server set the reason phrase to something more meaningful than "Found" in these cases. The user client SHOULD redirect automatically to the given URI. This response MUST NOT contain a message-body. This example shows a client being redirected to a different server: C->S: SETUP rtsp://example.com/fizzle/foo RTSP/2.0 CSeq: 2 Transport: RTP/AVP/TCP;unicast;interleaved=0-1 Accept-Ranges: NPT, SMPTE, UTC User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 302 Try Other Server CSeq: 2 Location: rtsp://s2.example.com:8001/fizzle/foo 15.3.4. 303 See Other This status code SHALL NOT be used in RTSP. However, it was allowed to use in RTSP 1.0 (RFC 2326). 15.3.5. 304 Not Modified If the client has performed a conditional DESCRIBE or SETUP (see Section 16.25) and the requested resource has not been modified, the server SHOULD send a 304 response. This response MUST NOT contain a message-body. The response MUST include the following header fields: Schulzrinne, et al. Expires May 7, 2009 [Page 89] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o Date o ETag and/or Content-Location, if the header(s) would have been sent in a 200 response to the same request. o Expires, Cache-Control, and/or Vary, if the field-value might differ from that sent in any previous response for the same variant. This response is independent for the DESCRIBE and SETUP requests. That is, a 304 response to DESCRIBE does NOT imply that the resource content is unchanged (only the session description) and a 304 response to SETUP does NOT imply that the resource description is unchanged. The ETag and If-Match headers may be used to link the DESCRIBE and SETUP in this manner. 15.3.6. 305 Use Proxy See [H10.3.6]. 15.4. Client Error 4xx 15.4.1. 400 Bad Request The request could not be understood by the server due to malformed syntax. The client SHOULD NOT repeat the request without modifications [H10.4.1]. If the request does not have a CSeq header, the server MUST NOT include a CSeq in the response. 15.4.2. 405 Method Not Allowed The method specified in the request is not allowed for the resource identified by the Request-URI. The response MUST include an Allow header containing a list of valid methods for the requested resource. This status code is also to be used if a request attempts to use a method not indicated during SETUP. 15.4.3. 451 Parameter Not Understood The recipient of the request does not support one or more parameters contained in the request. When returning this error message the sender SHOULD return a entity body containing the offending parameter(s). 15.4.4. 452 reserved This error code was removed from RFC 2326 [RFC2326] and is obsolete. Schulzrinne, et al. Expires May 7, 2009 [Page 90] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 15.4.5. 453 Not Enough Bandwidth The request was refused because there was insufficient bandwidth. This may, for example, be the result of a resource reservation failure. 15.4.6. 454 Session Not Found The RTSP session identifier in the Session header is missing, invalid, or has timed out. 15.4.7. 455 Method Not Valid in This State The client or server cannot process this request in its current state. The response SHALL contain an Allow header to make error recovery possible. 15.4.8. 456 Header Field Not Valid for Resource The server could not act on a required request header. For example, if PLAY contains the Range header field but the stream does not allow seeking. This error message may also be used for specifying when the time format in Range is impossible for the resource. In that case the Accept-Ranges header SHALL be returned to inform the client of which format(s) that are allowed. 15.4.9. 457 Invalid Range The Range value given is out of bounds, e.g., beyond the end of the presentation. 15.4.10. 458 Parameter Is Read-Only The parameter to be set by SET_PARAMETER can be read but not modified. When returning this error message the sender SHOULD return a entity body containing the offending parameter(s). 15.4.11. 459 Aggregate Operation Not Allowed The requested method may not be applied on the URI in question since it is an aggregate (presentation) URI. The method may be applied on a media URI. 15.4.12. 460 Only Aggregate Operation Allowed The requested method may not be applied on the URI in question since it is not an aggregate control (presentation) URI. The method may be applied on the aggregate control URI. Schulzrinne, et al. Expires May 7, 2009 [Page 91] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 15.4.13. 461 Unsupported Transport The Transport field did not contain a supported transport specification. 15.4.14. 462 Destination Unreachable The data transmission channel could not be established because the client address could not be reached. This error will most likely be the result of a client attempt to place an invalid dest_addr parameter in the Transport field. 15.4.15. 463 Destination Prohibited The data transmission channel was not established because the server prohibited access to the client address. This error is most likely the result of a client attempt to redirect media traffic to another destination with a dest_addr parameter in the Transport header. 15.4.16. 464 Data Transport Not Ready Yet The data transmission channel to the media destination is not yet ready for carrying data. However the responding entity still expects that the data transmission channel will be established at this point in time. Note however that this may result in a permanent failure like 462 "Destination Unreachable". An example when this error may occur is in the case a client sends a PLAY request to a server prior to ensuring that the TCP connections negotiated for carrying media data was successful established (In violation of this specification). The server would use this error code to indicate that the requested action could not be performed due to the failure of completing the connection establishment. 15.4.17. 465 Notification Reason Unknown The client has received a PLAY_NOTIFY (Section 13.5) with a Notify- Reason header (Section 16.31) indicates a reson that are unknown to the client. 15.4.18. 470 Connection Authorization Required The secured connection attempt need user or client authorization before proceeding. The next hops certificate is included in this response in the Accept-Credentials header. Schulzrinne, et al. Expires May 7, 2009 [Page 92] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 15.4.19. 471 Connection Credentials not accepted When performing a secure connection over multiple connections, a intermediary has refused to connect to the next hop and carry out the request due to unacceptable credentials for the used policy. 15.4.20. 472 Failure to establish secure connection A proxy fails to establish a secure connection to the next hop RTSP agent. This is primarily caused by a fatal failure at the TLS handshake, for example due to server not accepting any cipher suits. 15.5. Server Error 5xx 15.5.1. 551 Option not supported A feature-tag given in the Require or the Proxy-Require fields was not supported. The Unsupported header SHALL be returned stating the feature for which there is no support. Schulzrinne, et al. Expires May 7, 2009 [Page 93] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16. Header Field Definitions +---------------+----------------+--------+---------+------+ | method | direction | object | acronym | Body | +---------------+----------------+--------+---------+------+ | DESCRIBE | C -> S | P,S | DES | r | | | | | | | | GET_PARAMETER | C -> S, S -> C | P,S | GPR | R,r | | | | | | | | OPTIONS | C -> S | P,S | OPT | | | | | | | | | | S -> C | | | | | | | | | | | PAUSE | C -> S | P,S | PSE | | | | | | | | | PLAY | C -> S | P,S | PLY | | | | | | | | | PLAY_NOTIFY | S -> C | P,S | PNY | R | | | | | | | | REDIRECT | S -> C | P,S | RDR | | | | | | | | | SETUP | C -> S | S | STP | | | | | | | | | SET_PARAMETER | C -> S, S -> C | P,S | SPR | R,r | | | | | | | | TEARDOWN | C -> S | P,S | TRD | | +---------------+----------------+--------+---------+------+ Table 8: Overview of RTSP methods, their direction, and what objects (P: presentation, S: stream) they operate on. Body notes if a method is allowed to carry body and in which direction, R = Request, r=response. Note: It is allowed for all error messages 4xx and 5xx to have a body The general syntax for header fields is covered in Section 5.2. This section lists the full set of header fields along with notes on meaning, and usage. The syntax definition for header fields are present in Section 20.2.3. Throughout this section, we use [HX.Y] to refer to Section X.Y of the current HTTP/1.1 specification RFC 2616 [RFC2616]. Examples of each header field are given. Information about header fields in relation to methods and proxy processing is summarized in Table 9, Table 10, Table 11, and Table 12. The "where" column describes the request and response types in which the header field can be used. Values in this column are: Schulzrinne, et al. Expires May 7, 2009 [Page 94] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 R: header field may only appear in requests; r: header field may only appear in responses; 2xx, 4xx, etc.: A numerical value or range indicates response codes with which the header field can be used; c: header field is copied from the request to the response. An empty entry in the "where" column indicates that the header field may be present in both requests and responses. The "proxy" column describes the operations a proxy may perform on a header field. An empty proxy column indicates that the proxy SHALL NOT do any changes to that header, all allowed operations are explicitly stated: a: A proxy can add or concatenate the header field if not present. m: A proxy can modify an existing header field value. d: A proxy can delete a header field value. r: A proxy needs to be able to read the header field, and thus this header field cannot be encrypted. The rest of the columns relate to the presence of a header field in a method. The method names when abbreviated, are according to Table 8: c: Conditional; requirements on the header field depend on the context of the message. m: The header field is mandatory. m*: The header field SHOULD be sent, but clients/servers need to be prepared to receive messages without that header field. o: The header field is optional. *: The header field is SHALL be present if the message body is not empty. See Section 16.16, Section 16.18 and Section 5.3 for details. -: The header field is not applicable. "Optional" means that a Client/Server MAY include the header field in a request or response. The Client/Server behavior when receiving such headers varies, for some it may ignore the header field, in Schulzrinne, et al. Expires May 7, 2009 [Page 95] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 other case it is request to process the header. This is regulated by the method and header descriptions. Example of such headers that require processing are the Require and Proxy-Require header fields discussed in Section 16.42 and Section 16.35. A "mandatory" header field MUST be present in a request, and MUST be understood by the Client/Server receiving the request. A mandatory response header field MUST be present in the response, and the header field MUST be understood by the Client/Server processing the response. "Not applicable" means that the header field MUST NOT be present in a request. If one is placed in a request by mistake, it MUST be ignored by the Client/Server receiving the request. Similarly, a header field labeled "not applicable" for a response means that the Client/Server MUST NOT place the header field in the response, and the Client/Server MUST ignore the header field in the response. An RTSP agent SHALL ignore extension headers that are not understood. The From and Location header fields contain an URI. If the URI contains a comma, or semicolon, the URI MUST be enclosed in double quotas ("). Any URI parameters are contained within these quotas. If the URI is not enclosed in double quotas, any semicolon- delimited parameters are header-parameters, not URI parameters. +----------------+------+-----+-----+-----+------+-----+------+-----+ | Header | Wher | Pro | DES | OPT | SETU | PLA | PAUS | TRD | | | e | xy | | | P | Y | E | | +----------------+------+-----+-----+-----+------+-----+------+-----+ | Accept | R | | o | - | - | - | - | - | | | | | | | | | | | | Accept-Credent | R | r | o | o | o | o | o | o | | ials | | | | | | | | | | | | | | | | | | | | Accept-Encodin | R | r | o | - | - | - | - | - | | g | | | | | | | | | | | | | | | | | | | | Accept-Languag | R | r | o | - | - | - | - | - | | e | | | | | | | | | | | | | | | | | | | | Accept-Ranges | R | r | - | - | m | - | - | - | | | | | | | | | | | | Accept-Ranges | r | r | - | - | o | - | - | - | | | | | | | | | | | | Accept-Ranges | 456 | r | - | - | - | o | - | - | | | | | | | | | | | | Allow | r | am | c | c | c | - | - | - | | | | | | | | | | | | Allow | 405 | am | m | m | m | m | m | m | | | | | | | | | | | Schulzrinne, et al. Expires May 7, 2009 [Page 96] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Authorization | R | | o | o | o | o | o | o | | | | | | | | | | | | Bandwidth | R | | o | o | o | o | - | - | | | | | | | | | | | | Blocksize | R | | o | - | o | o | - | - | | | | | | | | | | | | Cache-Control | | r | o | - | o | - | - | - | | | | | | | | | | | | Connection | | | o | o | o | o | o | o | | | | | | | | | | | | Connection-Cre | 470, | ar | o | o | o | o | o | o | | dentials | 407 | | | | | | | | | | | | | | | | | | | Content-Base | r | | o | - | - | - | - | - | | | | | | | | | | | | Content-Base | 4xx, | | o | o | o | o | o | o | | | 5xx | | | | | | | | | | | | | | | | | | | Content-Encodi | R | r | - | - | - | - | - | - | | ng | | | | | | | | | | | | | | | | | | | | Content-Encodi | r | r | o | - | - | - | - | - | | ng | | | | | | | | | | | | | | | | | | | | Content-Encodi | 4xx, | r | o | o | o | o | o | o | | ng | 5xx | | | | | | | | | | | | | | | | | | | Content-Langua | R | r | - | - | - | - | - | - | | ge | | | | | | | | | | | | | | | | | | | | Content-Langua | r | r | o | - | - | - | - | - | | ge | | | | | | | | | | | | | | | | | | | | Content-Langua | 4xx, | r | o | o | o | o | o | o | | ge | 5xx | | | | | | | | | | | | | | | | | | | Content-Length | r | r | * | - | - | - | - | - | | | | | | | | | | | | Content-Length | 4xx, | r | * | * | * | * | * | * | | | 5xx | | | | | | | | | | | | | | | | | | | Content-Locati | r | | o | - | - | - | - | - | | on | | | | | | | | | | | | | | | | | | | | Content-Locati | 4xx, | | o | o | o | o | o | o | | on | 5xx | | | | | | | | | | | | | | | | | | | Content-Type | r | | * | - | - | - | - | - | Schulzrinne, et al. Expires May 7, 2009 [Page 97] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Content-Type | 4xx, | | * | * | * | * | * | * | | | 5xx | | | | | | | | | | | | | | | | | | | CSeq | Rc | rm | m | m | m | m | m | m | | | | | | | | | | | | Date | | am | o | o | o | o | o | o | | | | | | | | | | | | ETag | r | r | o | - | o | - | - | - | | | | | | | | | | | | Expires | r | r | o | - | - | - | - | - | | | | | | | | | | | | From | R | r | o | o | o | o | o | o | | | | | | | | | | | | If-Match | R | r | - | - | o | - | - | - | | | | | | | | | | | | If-Modified-Si | R | r | o | - | o | - | - | - | | nce | | | | | | | | | | | | | | | | | | | | If-None-Match | R | r | o | - | - | - | - | - | | | | | | | | | | | | Last-Modified | r | r | o | - | - | - | - | - | | | | | | | | | | | | Location | 3rr | | o | o | o | o | o | o | +----------------+------+-----+-----+-----+------+-----+------+-----+ Table 9: Overview of RTSP header fields (A-L) related to methods DESCRIBE, OPTIONS, SETUP, PLAY, PAUSE, and TEARDOWN. +------------+-------+------+----+-----+-------+------+-------+-----+ | Header | Where | Prox | DE | OPT | SETUP | PLAY | PAUSE | TRD | | | | y | S | | | | | | +------------+-------+------+----+-----+-------+------+-------+-----+ | Media- | | | - | - | r | r | r | - | | Properties | | | | | | | | | | | | | | | | | | | | Media- | | | - | - | r | r | r | - | | Range | | | | | | | | | | | | | | | | | | | | Pipelined- | | amdr | - | o | o | o | o | o | | Requests | | | | | | | | | | | | | | | | | | | | Proxy- | 407 | amr | m | m | m | m | m | m | | Authentica | | | | | | | | | | te | | | | | | | | | | | | | | | | | | | | Proxy- | R | rd | o | o | o | o | o | o | | Authorizat | | | | | | | | | | ion | | | | | | | | | Schulzrinne, et al. Expires May 7, 2009 [Page 98] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Proxy- | R | ar | o | o | o | o | o | o | | Require | | | | | | | | | | | | | | | | | | | | Proxy- | r | r | c | c | c | c | c | c | | Require | | | | | | | | | | | | | | | | | | | | Proxy- | R | amr | c | c | c | c | c | c | | Supported | | | | | | | | | | | | | | | | | | | | Proxy- | r | | c | c | c | c | c | c | | Supported | | | | | | | | | | | | | | | | | | | | Public | r | admr | - | m | - | - | - | - | | | | | | | | | | | | Public | 501 | admr | m | m | m | m | m | m | | | | | | | | | | | | Range | R | | - | - | - | o | - | - | | | | | | | | | | | | Range | r | | - | - | c | m | m | - | | | | | | | | | | | | Referer | R | | o | o | o | o | o | o | | | | | | | | | | | | Request- | R | | - | - | - | - | - | - | | Status | | | | | | | | | | | | | | | | | | | | Require | R | | o | o | o | o | o | o | | | | | | | | | | | | Retry-Afte | 3rr,5 | | o | o | o | - | - | - | | r | 03 | | | | | | | | | | | | | | | | | | | RTP-Info | r | | - | - | c | c | - | - | | | | | | | | | | | | Scale | | | - | - | - | o | - | - | | | | | | | | | | | | Seek-Style | R | | - | - | - | o | - | - | | | | | | | | | | | | Seek-Style | r | | - | - | - | m | - | - | | | | | | | | | | | | Session | R | r | - | o | o | m | m | m | | | | | | | | | | | | Session | r | r | - | c | m | m | m | o | | | | | | | | | | | | Server | R | r | - | o | - | - | - | - | | | | | | | | | | | | Server | r | r | o | o | o | o | o | o | | | | | | | | | | | | Speed | | | - | - | - | o | - | - | | | | | | | | | | | Schulzrinne, et al. Expires May 7, 2009 [Page 99] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Supported | R | amr | o | o | o | o | o | o | | | | | | | | | | | | Supported | r | amr | c | c | c | c | c | c | | | | | | | | | | | | Timestamp | R | admr | o | o | o | o | o | o | | | | | | | | | | | | Timestamp | c | admr | m | m | m | m | m | m | | | | | | | | | | | | Transport | | amr | - | - | m | - | - | - | | | | | | | | | | | | Unsupporte | r | | c | c | c | c | c | c | | d | | | | | | | | | | | | | | | | | | | | User-Agent | R | | m* | m* | m* | m* | m* | m* | | | | | | | | | | | | Vary | r | | c | c | c | c | c | c | | | | | | | | | | | | Via | R | amr | o | o | o | o | o | o | | | | | | | | | | | | Via | c | dr | m | m | m | m | m | m | | | | | | | | | | | | WWW- | 401 | | m | m | m | m | m | m | | Authentica | | | | | | | | | | te | | | | | | | | | +------------+-------+------+----+-----+-------+------+-------+-----+ Table 10: Overview of RTSP header fields (P-W) related to methods DESCRIBE, OPTIONS, SETUP, PLAY, PAUSE, and TEARDOWN. +------------------------+---------+-------+-----+-----+-----+-----+ | Header | Where | Proxy | GPR | SPR | RDR | PNY | +------------------------+---------+-------+-----+-----+-----+-----+ | Accept-Credentials | R | r | o | o | o | - | | | | | | | | | | Allow | 405 | amr | m | m | m | - | | | | | | | | | | Authorization | R | | o | o | o | - | | | | | | | | | | Bandwidth | R | | - | o | - | - | | | | | | | | | | Blocksize | R | | - | o | - | - | | | | | | | | | | Connection | | | o | o | o | - | | | | | | | | | | Connection-Credentials | 470,407 | ar | o | o | o | - | | | | | | | | | | Content-Base | R | | o | o | - | - | | | | | | | | | Schulzrinne, et al. Expires May 7, 2009 [Page 100] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Content-Base | r | | o | o | - | - | | | | | | | | | | Content-Base | 4xx,5xx | | o | o | o | - | | | | | | | | | | Content-Encoding | R | r | o | o | - | - | | | | | | | | | | Content-Encoding | r | r | o | o | - | - | | | | | | | | | | Content-Encoding | 4xx,5xx | r | o | o | o | - | | | | | | | | | | Content-Language | R | r | o | o | - | - | | | | | | | | | | Content-Language | r | r | o | o | - | - | | | | | | | | | | Content-Language | 4xx,5xx | r | o | o | o | - | | | | | | | | | | Content-Length | R | r | * | * | - | - | | | | | | | | | | Content-Length | r | r | * | * | - | - | | | | | | | | | | Content-Length | 4xx,5xx | r | * | * | * | - | | | | | | | | | | Content-Location | R | | o | o | - | - | | | | | | | | | | Content-Location | r | | o | o | - | - | | | | | | | | | | Content-Location | 4xx,5xx | | o | o | o | - | | | | | | | | | | Content-Type | R | | * | * | - | - | | | | | | | | | | Content-Type | r | | * | * | - | - | | | | | | | | | | Content-Type | 4xx | | * | * | * | - | | | | | | | | | | CSeq | R,c | mr | m | m | m | m | | | | | | | | | | Date | R | a | o | o | m | - | | | | | | | | | | Date | r | am | o | o | o | - | | | | | | | | | | From | R | r | o | o | o | - | | | | | | | | | | Last-Modified | R | r | - | - | - | - | | | | | | | | | | Last-Modified | r | r | o | - | - | - | | | | | | | | | | Location | 3rr | | o | o | o | - | | | | | | | | | Schulzrinne, et al. Expires May 7, 2009 [Page 101] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Location | R | | - | - | m | - | | | | | | | | | | Media-Properties | | | - | - | - | | | | | | | | | | | Media-Range | R | | o | - | - | c | | | | | | | | | | Media-Range | r | | c | - | - | - | | | | | | | | | | Notify-Reason | R | | - | - | - | m | | | | | | | | | | Pipelined-Requests | | amdr | o | o | o | - | | | | | | | | | | Proxy-Authenticate | 407 | amr | m | m | m | - | | | | | | | | | | Proxy-Authorization | R | rd | o | o | o | - | | | | | | | | | | Proxy-Require | R | ar | o | o | o | - | | | | | | | | | | Proxy-Require | r | r | c | c | c | - | | | | | | | | | | Proxy-Supported | R | amr | c | c | c | - | | | | | | | | | | Proxy-Supported | r | | c | c | c | - | | | | | | | | | | Public | 501 | admr | m | m | m | - | +------------------------+---------+-------+-----+-----+-----+-----+ Table 11: Overview of RTSP header fields (A-P) related to methods GET_PARAMETER, SET_PARAMETER, PLAY_NOTIFY, and REDIRECT. +------------------+---------+-------+-----+-----+-----+-----+ | Header | Where | Proxy | GPR | SPR | RDR | PNY | +------------------+---------+-------+-----+-----+-----+-----+ | Range | R | | - | - | o | m | | | | | | | | | | Referer | R | | o | o | o | - | | | | | | | | | | Request-Status | R | | - | - | - | m | | | | | | | | | | Require | R | r | o | o | o | - | | | | | | | | | | Retry-After | 3rr,503 | | o | o | - | - | | | | | | | | | | Scale | | | - | - | - | c | | | | | | | | | | Seek-Style | | | - | - | - | - | | | | | | | | | | Session | R | r | o | o | o | m | Schulzrinne, et al. Expires May 7, 2009 [Page 102] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 | Session | r | r | c | c | o | m | | | | | | | | | | Server | R | r | o | o | o | - | | | | | | | | | | Server | r | r | o | o | - | - | | | | | | | | | | Supported | R | adrm | o | o | o | - | | | | | | | | | | Supported | r | adrm | c | c | c | - | | | | | | | | | | Timestamp | R | adrm | o | o | o | - | | | | | | | | | | Timestamp | c | adrm | m | m | m | - | | | | | | | | | | Unsupported | r | arm | c | c | c | - | | | | | | | | | | User-Agent | R | r | m* | m* | - | - | | | | | | | | | | User-Agent | r | r | - | - | m* | - | | | | | | | | | | Vary | r | | c | c | - | - | | | | | | | | | | Via | R | amr | o | o | o | - | | | | | | | | | | Via | c | dr | m | m | m | - | | | | | | | | | | WWW-Authenticate | 401 | | m | m | m | - | +------------------+---------+-------+-----+-----+-----+-----+ Table 12: Overview of RTSP header fields (R-W) related to methods GET_PARAMETER, SET_PARAMETER, PLAY_NOTIFY, and REDIRECT. 16.1. Accept The Accept request-header field can be used to specify certain presentation description content types which are acceptable for the response. See [H14.1] for syntax. Example of use: Accept: application/example ;q=1.0, application/sdp 16.2. Accept-Credentials The Accept-Credentials header is a request header used to indicate to any trusted intermediary how to handle further secured connections to proxies or servers. See Section 19 for the usage of this header. It Schulzrinne, et al. Expires May 7, 2009 [Page 103] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 SHALL NOT be included in server to client requests. In a request the header SHALL contain the method (User, Proxy, or Any) for approving credentials selected by the requestor. The method SHALL NOT be changed by any proxy, unless it is "proxy" when a proxy MAY change it to "user" to take the role of user approving each further hop. If the method is "User" the header contains zero or more of credentials that the client accepts. The header may contain zero credentials in the first RTSP request to a RTSP server when using the "User" method. This as the client has not yet received any credentials to accept. Each credential SHALL consist of one URI identifying the proxy or server, the hash algorithm identifier, and the hash over that entity's DER encoded certificate [RFC5280] in Base64 [RFC4648]. All RTSP clients and proxies SHALL implement the SHA-256[FIPS-pub-180-2] algorithm for computation of the hash of the DER encoded certificate. The SHA-256 algorithm is identified by the token "sha-256". The intention with allowing for other hash algorithms is to enable the future retirement of algorithms that are not implemented somewhere else than here. Thus the definition of future algorithms for this purpose is intended to be extremely limited. A feature tag can be used to ensure that support for the replacement algorithm exist. Example: Accept-Credentials:User "rtsps://proxy2.example.com/";sha-256;exaIl9VMbQMOFGClx5rXnPJKVNI=, "rtsps://server.example.com/";sha-256;lurbjj5khhB0NhIuOXtt4bBRH1M= 16.3. Accept-Encoding See [H14.3]. 16.4. Accept-Language See [H14.4]. Note that the language specified applies to the presentation description and any reason phrases, not the media content. 16.5. Accept-Ranges The Accept-Ranges request and response-header field allows indication of the format supported in the Range header. The client SHALL include the header in SETUP requests to indicate which formats it support to receive in PLAY and PAUSE responses, and REDIRECT requests. The server SHALL include the header in SETUP and 456 error responses to indicate the formats supported for the resource Schulzrinne, et al. Expires May 7, 2009 [Page 104] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 indicated by the request URI. Accept-Ranges: NPT, SMPTE This header has the same syntax as [H14.5] and the syntax is defined in Section 20.2.3. However, new range-units are defined. 16.6. Allow The Allow entity-header field lists the methods supported by the resource identified by the Request-URI. The purpose of this field is to strictly inform the recipient of valid methods associated with the resource. An Allow header field MUST be present in a 405 (Method Not Allowed) response. See [H14.7] for syntax definition. The Allow header MUST also be present in all OPTIONS responses where the content of the header will not include exactly the same methods as listed in the Public header. The Allow SHALL also be included in SETUP and DESCRIBE responses, if the methods allowed for the resource is different than the minimal implementation set. Example of use: Allow: SETUP, PLAY, SET_PARAMETER, DESCRIBE 16.7. Authorization See [H14.8]. 16.8. Bandwidth The Bandwidth request-header field describes the estimated bandwidth available to the client, expressed as a positive integer and measured in bits per second. The bandwidth available to the client may change during an RTSP session, e.g., due to mobility, congestion, etc. Example: Bandwidth: 62360 16.9. Blocksize The Blocksize request-header field is sent from the client to the media server asking the server for a particular media packet size. This packet size does not include lower-layer headers such as IP, UDP, or RTP. The server is free to use a blocksize which is lower than the one requested. The server MAY truncate this packet size to the closest multiple of the minimum, media-specific block size, or override it with the media-specific size if necessary. The block size MUST be a positive decimal number, measured in octets. The Schulzrinne, et al. Expires May 7, 2009 [Page 105] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 server only returns an error (4xx) if the value is syntactically invalid. 16.10. Cache-Control The Cache-Control general-header field is used to specify directives that MUST be obeyed by all caching mechanisms along the request/ response chain. Cache directives MUST be passed through by a proxy or gateway application, regardless of their significance to that application, since the directives may be applicable to all recipients along the request/response chain. It is not possible to specify a cache- directive for a specific cache. Cache-Control should only be specified in a SETUP request and its response. Note: Cache-Control does not govern the caching of responses as for HTTP, instead it applies to the media stream identified by the SETUP request. The RTSP requests are generally not cacheable, for further information see Section 18. Below is the description of the cache directives that can be included in the Cache-Control header. no-cache: Indicates that the media stream MUST NOT be cached anywhere. This allows an origin server to prevent caching even by caches that have been configured to return stale responses to client requests. Note, there is no security function enforcing that the content can't be cached. public: Indicates that the media stream is cacheable by any cache. private: Indicates that the media stream is intended for a single user and MUST NOT be cached by a shared cache. A private (non- shared) cache may cache the media streams. no-transform: An intermediate cache (proxy) may find it useful to convert the media type of a certain stream. A proxy might, for example, convert between video formats to save cache space or to reduce the amount of traffic on a slow link. Serious operational problems may occur, however, when these transformations have been applied to streams intended for certain kinds of applications. For example, applications for medical imaging, scientific data analysis and those using end- to-end authentication all depend on receiving a stream that is bit-for-bit identical to the original media stream. Therefore, if a response includes the no-transform directive, an intermediate cache or proxy MUST NOT change the encoding of the stream. Unlike HTTP, RTSP does not provide for partial Schulzrinne, et al. Expires May 7, 2009 [Page 106] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 transformation at this point, e.g., allowing translation into a different language. only-if-cached: In some cases, such as times of extremely poor network connectivity, a client may want a cache to return only those media streams that it currently has stored, and not to receive these from the origin server. To do this, the client may include the only-if-cached directive in a request. If it receives this directive, a cache SHOULD either respond using a cached media stream that is consistent with the other constraints of the request, or respond with a 504 (Gateway Timeout) status. However, if a group of caches is being operated as a unified system with good internal connectivity, such a request MAY be forwarded within that group of caches. max-stale: Indicates that the client is willing to accept a media stream that has exceeded its expiration time. If max-stale is assigned a value, then the client is willing to accept a response that has exceeded its expiration time by no more than the specified number of seconds. If no value is assigned to max-stale, then the client is willing to accept a stale response of any age. min-fresh: Indicates that the client is willing to accept a media stream whose freshness lifetime is no less than its current age plus the specified time in seconds. That is, the client wants a response that will still be fresh for at least the specified number of seconds. must-revalidate: When the must-revalidate directive is present in a SETUP response received by a cache, that cache MUST NOT use the entry after it becomes stale to respond to a subsequent request without first revalidating it with the origin server. That is, the cache is required to do an end-to-end revalidation every time, if, based solely on the origin server's Expires, the cached response is stale.) proxy-revalidate: The proxy-revalidate directive has the same meaning as the must-revalidate directive, except that it does not apply to non-shared user agent caches. It can be used on a response to an authenticated request to permit the user's cache to store and later return the response without needing to revalidate it (since it has already been authenticated once by that user), while still requiring proxies that service many users to revalidate each time (in order to make sure that each user has been authenticated). Note that such authenticated responses also need the public cache control directive in order to allow them to be cached at all. Schulzrinne, et al. Expires May 7, 2009 [Page 107] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 max-age: When an intermediate cache is forced, by means of a max- age=0 directive, to revalidate its own cache entry, and the client has supplied its own validator in the request, the supplied validator might differ from the validator currently stored with the cache entry. In this case, the cache MAY use either validator in making its own request without affecting semantic transparency. However, the choice of validator might affect performance. The best approach is for the intermediate cache to use its own validator when making its request. If the server replies with 304 (Not Modified), then the cache can return its now validated copy to the client with a 200 (OK) response. If the server replies with a new entity and cache validator, however, the intermediate cache can compare the returned validator with the one provided in the client's request, using the strong comparison function. If the client's validator is equal to the origin server's, then the intermediate cache simply returns 304 (Not Modified). Otherwise, it returns the new entity with a 200 (OK) response. 16.11. Connection See [H14.10]. The use of the connection option "close" in RTSP messages SHOULD be limited to error messages when the server is unable to recover and therefore see it necessary to close the connection. The reason is that the client has the choice of continuing using a connection indefinitely, as long as it sends valid messages. 16.12. Connection-Credentials The Connection-Credentials response header is used to carry the chain of credentials of any next hop that need to be approved by the requestor. It SHALL only be used in server to client responses. The Connection-Credentials header in an RTSP response SHALL, if included, contain the credential information (in form of a list of certificates providing the chain of certification) of the next hop that an intermediary needs to securely connect to. The header MUST include the URI of the next hop (proxy or server) and a base64 [RFC4648] encoded binary structure containg a sequence of DER encoded X.509v3 certificates[RFC5280] . The binary structure starts with the number of certificates (NR_CERTS) included as a 16 bit unsigned integer. This is followed by NR_CERTS number of 16 bit unsigned integers providing the size in octets of each DER encoded certificate. This is followed by NR_CERTS number of DER encoded X.509v3 certificates in a sequence (chain). Schulzrinne, et al. Expires May 7, 2009 [Page 108] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The proxy or server's certificate must come first in the structure. Each following certificate must directly certify the one preceding it. Because certificate validation requires that root keys be distributed independently, the self-signed certificate which specifies the root certificate authority may optionally be omitted from the chain, under the assumption that the remote end must already possess it in order to validate it in any case. Example: Connection-Credentials:"rtsps://proxy2.example.com/";MIIDNTCC... Where MIIDNTCC... is a BASE64 encoding of the following structure: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Number of certifcates | Size of certificate #1 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Size of certificate #2 | Size of certificate #3 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : DER Encoding of Certificate #1 : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : DER Encoding of Certificate #2 : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : DER Encoding of Certificate #3 : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 16.13. Content-Base The Content-Base entity-header field may be used to specify the base URI for resolving relative URIs within the entity. Content-Base: rtsp://media.example.com/movie/twister If no Content-Base field is present, the base URI of an entity is defined either by its Content-Location (if that Content-Location URI is an absolute URI) or the URI used to initiate the request, in that order of precedence. Note, however, that the base URI of the contents within the entity-body may be redefined within that entity- body. 16.14. Content-Encoding See [H14.11]. 16.15. Content-Language See [H14.12]. Schulzrinne, et al. Expires May 7, 2009 [Page 109] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.16. Content-Length The Content-Length general-header field contains the length of the body (entity) of the message (i.e. after the double CRLF following the last header). Unlike HTTP, it MUST be included in all messages that carry body beyond the header portion of the message. If it is missing, a default value of zero is assumed. It is interpreted according to [H14.13]. 16.17. Content-Location See [H14.14]. 16.18. Content-Type See [H14.17]. Note that the content types suitable for RTSP are likely to be restricted in practice to presentation descriptions and parameter-value types. 16.19. CSeq The CSeq general-header field specifies the sequence number for an RTSP request-response pair. This field MUST be present in all requests and responses. For every RTSP request containing the given sequence number, the corresponding response will have the same number. Any retransmitted request MUST contain the same sequence number as the original (i.e. the sequence number is not incremented for retransmissions of the same request). For each new RTSP request the CSeq value SHALL be incremented by one. The initial sequence number MAY be any number, however it is RECOMMENDED to start at 0. Each sequence number series is unique between each requester and responder, i.e. the client has one series for its request to a server and the server has another when sending request to the client. Each requester and responder is identified with its network address. Proxies that aggregate several sessions on the same transport will regularly need to renumber the CSeq header field in requests and responses to fulfill the rules for the header. Example: CSeq: 239 16.20. Date See [H14.18]. An RTSP message containing a body MUST include a Date header if the sending host has a clock. Servers SHOULD include a Date header in all other RTSP messages. Schulzrinne, et al. Expires May 7, 2009 [Page 110] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.21. ETag The ETag response header MAY be included in DESCRIBE or SETUP responses. The entity tags (Section 4.8) returned in a DESCRIBE response, and the one in SETUP refers to the presentation, i.e. both the returned session description and the media stream. This allows for verification that one has the right session description to a media resource at the time of the SETUP request. However it has the disadvantage that a change in any of the parts results in invalidation of all the parts. If the ETag is provided both inside the entity, e.g. within the "a=etag" attribute in SDP, and in the response message, then both tags SHALL be identical. It is RECOMMENDED that the ETag is primarily given in the RTSP response message, to ensure that caches can use the ETag without requiring content inspection. However for session descriptions that are distributed outside of RTSP, for example using HTTP, etc. it will be necessary to include the entity tag in the session description as specified in Appendix D.1.9. SETUP and DESCRIBE requests can be made conditional upon the ETag using the headers If-Match (Section 16.24) and If-None-Match ( Section 16.26). 16.22. Expires The Expires entity-header field gives a date and time after which the description or media-stream should be considered stale. The interpretation depends on the method: DESCRIBE response: The Expires header indicates a date and time after which the presentation description (body) SHOULD be considered stale. SETUP response: The Expires header indicate a date and time after which the media stream SHOULD be considered stale. A stale cache entry may not normally be returned by a cache (either a proxy cache or an user agent cache) unless it is first validated with the origin server (or with an intermediate cache that has a fresh copy of the entity). See Section 18 for further discussion of the expiration model. The presence of an Expires field does not imply that the original resource will change or cease to exist at, before, or after that time. The format is an absolute date and time as defined by HTTP-date in Schulzrinne, et al. Expires May 7, 2009 [Page 111] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 [H3.3]; it MUST be in RFC1123-date format: An example of its use is Expires: Thu, 01 Dec 1994 16:00:00 GMT RTSP/2.0 clients and caches MUST treat other invalid date formats, especially including the value "0", as having occurred in the past (i.e., already expired). To mark a response as "already expired," an origin server should use an Expires date that is equal to the Date header value. To mark a response as "never expires," an origin server SHOULD use an Expires date approximately one year from the time the response is sent. RTSP/2.0 servers SHOULD NOT send Expires dates more than one year in the future. 16.23. From See [H14.22]. 16.24. If-Match See [H14.24]. The If-Match request-header field is especially useful for ensuring the integrity of the presentation description, in both the case where it is fetched via means external to RTSP (such as HTTP), or in the case where the server implementation is guaranteeing the integrity of the description between the time of the DESCRIBE message and the SETUP message. By including the ETag given in or with the session description in a SETUP request, the client ensures that resources set up are matching the description. A SETUP request for which the ETag validation check fails, SHALL responde using 412 (Precondition Failed). This validation check is also very useful if a session has been redirected from one server to another. 16.25. If-Modified-Since The If-Modified-Since request-header field is used with the DESCRIBE and SETUP methods to make them conditional. If the requested variant has not been modified since the time specified in this field, a description will not be returned from the server (DESCRIBE) or a stream will not be set up (SETUP). Instead, a 304 (Not Modified) response SHALL be returned without any message-body. An example of the field is: Schulzrinne, et al. Expires May 7, 2009 [Page 112] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 If-Modified-Since: Sat, 29 Oct 1994 19:43:31 GMT 16.26. If-None-Match See [H14.26]. This request header can be used with one or several entity tags to make DESCRIBE requests conditional. A new session description is retrieved only if another entity than the ones already available would be included. If the entity available for delivery is matching the one the client already has, then a 304 (Not Modified) response is given. 16.27. Last-Modified The Last-Modified entity-header field indicates the date and time at which the origin server believes the presentation description or media stream was last modified. See [H14.29]. For the methods DESCRIBE, the header field indicates the last modification date and time of the description, for SETUP that of the media stream. 16.28. Location See [H14.30]. 16.29. Media-Properties This general header is used in SETUP response or PLAY_NOTIFY requests to indicate the media's properties that currently are applicable to the RTSP session. PLAY_NOTIFY MAY be used to modify these properties at any point. However, the client MUST have received the update prior to any action related to the new media properties take affect. For aggregated sessions the Media-Properties header will be returned in each SETUP response and the one that applies is the response to the last request. The media properties expressed by this header is the one applicable to all media in the RTSP session. So for aggregated sessions the header expressed the combined media-properties. As a result aggregation of media MAY result in a change of the media properties, and thus the content of the Media-Properties header contained in subsequent SETUP responses. The header contains a list of property values that are applicable to the currently setup media or aggregate of media as indicated by the RTSP URI in the request. No ordering are enforced within the header. Property values should be grouped into a single group that handles a particular orthogonal property. Values or groups that express Schulzrinne, et al. Expires May 7, 2009 [Page 113] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 multiple properties SHOULD NOT be used. The list of properties that can be expressed MAY be extended at any time. Unknown property values SHALL be ignored. This specification defines the following 3 groups and their property values: Random Access: Random-Access: Indicates that random access is possible. May optionally include a floating point value in seconds indicating the longest duration between any two random access points in the media. Begining-Only: Seeking is limited to the begining only. No-Seeking: No seeking is possible. Content Modifications Unmutable: The content will not be changed during the life-time of the RTSP session. Dynamic: The content may be changed based on external methods or triggers Time-Progressing The media accesible progress as wall clock time progresses. Retention Unlimited: Content will be retained for the duration of the life- time of the RTSP session. Time-Limited: Content will be retained at least until the specified wall clock time. The time must be provided in the absolute time format specified in Section Section 4.6. Time-Duration Each individual media unit is retained for at least the specified time duration. This definition allows for retaining data with a time based sliding window. The time duration is expressed as floating point number in seconds. 0.0 is a valid value as this indicates that no data is retained in a time-progressing session. An Example of this header for first an on-demand content and then a live stream without recording. Schulzrinne, et al. Expires May 7, 2009 [Page 114] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 On-demand: Media-Properties: Random-Acess=2.5s, Unlimited, Unmutable Live stream without recording/timeshifting: Media-Properties: No-Seeking, Time-Progressing, Time-Duration=0.0 16.30. Media-Range The Media-Range general header is used to give the range of the media at the time of sending the RTSP message. This header SHALL be included in SETUP response, and PLAY and PAUSE response for media that are Time-Progressing, and PLAY and PAUSE response after any change for media that are Dynamic, and in PLAY_NOTIFY request that are sent due to Media-Property-Update. Media-Range header without any range specifications MAY be included in GET_PARAMETER requests to the server to request the current value. The server SHALL in this case include the curent value at the time of sending the response. The header SHALL include range specification for all time formats supported for the media, as indicated in Accept-Ranges header (Section 16.5) when setting up the media. The server MAY include more than one range specification of any given time format to indicate media that has non-continous range. For media that has the Time-Progressing property, the Media-Range values will only be valid for the particular point in time when it was issued. As wall clock progresses so will also the media range. However it shall be assumed that media time progress in direct relationship to wall clock time (with the exception of clock skew) so that a reasoanbly accurate estiamation of the media range can be calculated. 16.31. Notify-Reason The Notify Reason header is solely used in the PLAY_NOTIFY method. It indiciates the reason why the server has sent the asynchronous PLAY_NOTIFY request (see Section 13.5). 16.32. Pipelined-Requests The Pipelined-Requests general header is used to indicate that a request is to be executed in the context created by previous requests. The primary usage of this header is to allow pipelining of SETUP requests so that any additional SETUP request after the first one doesn't need to wait for the session ID to be sent back to the requesting entity. The header contains a unique identifier that is scoped by the persistent connection used to send the requests. Schulzrinne, et al. Expires May 7, 2009 [Page 115] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Upon receiving a request with the Pipelined-Requests the responding entity SHALL look up if there exist a binding between this Pipelined- Requests identifier for the current persistent connection and an RTSP session ID. If that exist then the received request is processed the same way as if it did contain the Session header with the looked up session ID. If there doesn't exist a mapping and no Session header is included in the request, the responding entity SHALL create a binding upon the succesful completion of a session creating request, i.e. SETUP. If the request failed to create an RTSP session no binding SHALL be created. In case the request contains both a Session header and the Pipelined-Requests header the Pipelined- Requests SHALL be ignored. Note: Based on the above definition at least the first request containing a new unique Pipelined-Requests will be required to be a SETUP request (unless the protocol is extended with new methods of creating a session). After that first one, additional SETUP requests or request of any type using the RTSP session context may include the Pipelined-Requests header. For all responses to request that contained the Pipelined-Requests, the Session header and the Pipelined-Requests SHALL both be included, assuming that it is allowed for that response and that the binding between the header values exist. Pipelined-Requests SHOULD NOT be used in requests after that the client has received the RTSP Session ID. This as using the real session ID allows the request to be used also in cases the persistent connection has been terminated and a new connection is needed. It is the sender of the request that is responsible for using a previously unused identifier within this transport connection scope when a new RTSP session is to be cretated with this method. A server side binding SHALL be deleted upon the termination of the related RTSP session. Note: Although this definition would allow for reusing previously used pipelining identifiers, this is NOT RECOMMENDED to allow for better error handling and logging. RTSP Proxies may need to translate Pipelined-Requests identifier values from incoming request to outgoing to allow for aggregation of requests onto a persistent connection. 16.33. Proxy-Authenticate See [H14.33]. Schulzrinne, et al. Expires May 7, 2009 [Page 116] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.34. Proxy-Authorization See [H14.34]. 16.35. Proxy-Require The Proxy-Require request-header field is used to indicate proxy- sensitive features that MUST be supported by the proxy. Any Proxy- Require header features that are not supported by the proxy MUST be negatively acknowledged by the proxy to the client using the Unsupported header. The proxy SHALL use the 551 (Option Not Supported) status code in the response. Any feature-tag included in the Proxy-Require does not apply to the end-point (server or client). To ensure that a feature is supported by both proxies and servers the tag needs to be included in also a Require header. See Section 16.42 for more details on the mechanics of this message and a usage example. See discussion in the proxies section (Section 17.1) about when to consider that a feature requires proxy support. Example of use: Proxy-Require: play.basic 16.36. Proxy-Supported The Proxy-Supported header field enumerates all the extensions supported by the proxy using feature-tags. The header carries the intersection of extensions supported by the forwarding proxies. The Proxy-Supported header MAY be included in any request by a proxy. It SHALL be added by any proxy if the Supported header is present in a request. When present in a request, the receiver MUST in the response copy the received Proxy-Supported header. The Proxy-Supported header field contains a list of feature-tags applicable to proxies, as described in Section 4.7. The list are the intersection of all feature-tags understood by the proxies. To achieve an intersection, the proxy adding the Proxy-Supported header includes all proxy feature-tags it understands. Any proxy receiving a request with the header, checks the list and removes any feature- tag it do not support. A Proxy-Supported header present in the response SHALL NOT be touched by the proxies. Example: Schulzrinne, et al. Expires May 7, 2009 [Page 117] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->P1: OPTIONS rtsp://example.com/ RTSP/2.0 Supported: foo, bar, blech User-Agent: PhonyClient/1.2 P1->P2: OPTIONS rtsp://example.com/ RTSP/2.0 Supported: foo, bar, blech Proxy-Supported: proxy-foo, proxy-bar, proxy-blech Via: 2.0 prox1.example.com P2->S: OPTIONS rtsp://example.com/ RTSP/2.0 Supported: foo, bar, blech Proxy-Supported: proxy-foo, proxy-blech Via: 2.0 prox1.example.com, 2.0 prox2.example.com S->C: RTSP/2.0 200 OK Supported: foo, bar, baz Proxy-Supported: proxy-foo, proxy-blech Public: OPTIONS, SETUP, PLAY, PAUSE, TEARDOWN Via: 2.0 prox1.example.com, 2.0 prox2.example.com 16.37. Public The Public response header field lists the set of methods supported by the response sender. This header applies to the general capabilities of the sender and its only purpose is to indicate the sender's capabilities to the recipient. The methods listed may or may not be applicable to the Request-URI; the Allow header field (section 14.7) MAY be used to indicate methods allowed for a particular URI. Example of use: Public: OPTIONS, SETUP, PLAY, PAUSE, TEARDOWN In the event that there are proxies between the sender and the recipient of a response, each intervening proxy MUST modify the Public header field to remove any methods that are not supported via that proxy. The resulting Public header field will contain an intersection of the sender's methods and the methods allowed through by the intervening proxies. In general proxies should allow all methods to transparently pass through from the sending RTSP agent to the receiving RTSP agent, but there may be cases where this is not desirable for a given proxy. Modification of the Public response header field by the intervening proxies ensures that the request sender gets an accurate response indicating the methods that can be used on the target agent via the proxy chain. Schulzrinne, et al. Expires May 7, 2009 [Page 118] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.38. Range The Range header specifies a time range in PLAY (Section 13.4), PAUSE (Section 13.6), SETUP (Section 13.3), REDIRECT (Section 13.10), and PLAY_NOTIFY (Section 13.5) requests and responses. The range can be specified in a number of units. This specification defines smpte (Section 4.4), npt (Section 4.5), and clock (Section 4.6) range units. While byte ranges [H14.35.1] and other extended units MAY be used, their behavior is unspecified since they are not normally meaningful in RTSP. Servers supporting the Range header MUST understand the NPT range format and SHOULD understand the SMPTE range format. If the Range header is sent in a time format that is not understood, the recipient SHOULD return 456 (Header Field Not Valid for Resource) and include an Accept-Ranges header indicating the supported time formats for the given resource. The Range header MAY contain a time parameter in UTC, specifying the time at which the operation is to be made effective. This functionality SHALL be used only with the REDIRECT method. Example: Range: clock=19960213T143205Z-;time=19970123T143720Z The notation is similar to that used for the HTTP/1.1 [RFC2616] byte-range header. It allows clients to select an excerpt from the media object, and to play from a given point to the end as well as from the current location to a given point. Ranges are half-open intervals, including the first point, but excluding the second point. In other words, a range of A-B starts exactly at time A, but stops just before B. Only the start time of a media unit such as a video or audio frame is relevant. For example, assume that video frames are generated every 40 ms. A range of 10.0- 10.1 would include a video frame starting at 10.0 or later time and would include a video frame starting at 10.08, even though it lasted beyond the interval. A range of 10.0-10.08, on the other hand, would exclude the frame at 10.08. By default, range intervals increase, where the second point is larger than the first point. Example: Range: npt=10-15 However, range intervals can also decrease if the Scale header (see Section 16.44) indicates a negative scale value. For example, this would be the case when a playback in reverse is desired. Schulzrinne, et al. Expires May 7, 2009 [Page 119] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Example: Scale: -1 Range: npt=15-10 Decreasing ranges are still half open intervals as described above. Thus, for range A-B, A is closed and B is open. In the above example, 15 is closed and 10 is open. An exception to this rule is the case when B=0 in a decreasing range. In this case, the range is closed on both ends, as otherwise there would be no way to reach 0 on a reverse playback for formats that have such a notion, like NPT and SMPTE. Example: Scale: -1 Range: npt=15-0 In this range both 15 and 0 are closed. A decreasing range interval without a corresponding negative Scale header is not valid. 16.39. Referer See [H14.36]. The URI refers to that of the presentation description, typically retrieved via HTTP. 16.40. Retry-After See [H14.37]. 16.41. Request-Status This request header is used to indicate the end result for requests that takes time to complete, such a PLAY (Section 13.4). It is sent in PLAY_NOTIFY (Section 13.5) with the end-of-stream reason to report how the PLAY request concluded, either in success or in failure. The header carries a reference to the request is reports on using the CSeq number for the session indicated by the Session header in the request. It provies both a numerical status code (according to Section 8.1.1) and a human readable reason phrase. Example: Request-Status: cseq=63 status=500 reason="Media data unavailable" Schulzrinne, et al. Expires May 7, 2009 [Page 120] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.42. Require The Require request-header field is used by clients or servers to ensure that the other end-point supports features that are required in respect to this request. It can also be used to query if the other end-point supports certain features, however the use of the Supported (Section 16.49) is much more effective in this purpose. The server MUST respond to this header by using the Unsupported header to negatively acknowledge those feature-tags which are NOT supported. The response SHALL use the error code 551 (Option Not Supported). This header does not apply to proxies, for the same functionality in respect to proxies see Proxy-Require header (Section 16.35) with the exception of media modifying proxies. Media modifying proxies due to their nature of handling media in a way that is very similar to what a server, do need to understand also the server features to correctly serve the client. This is to make sure that the client-server interaction will proceed without delay when all features are understood by both sides, and only slow down if features are not understood (as in the example below). For a well-matched client-server pair, the interaction proceeds quickly, saving a round-trip often required by negotiation mechanisms. In addition, it also removes state ambiguity when the client requires features that the server does not understand. Example (Not complete): C->S: SETUP rtsp://server.com/foo/bar/baz.rm RTSP/2.0 CSeq: 302 Require: funky-feature Funky-Parameter: funkystuff S->C: RTSP/2.0 551 Option not supported CSeq: 302 Unsupported: funky-feature In this example, "funky-feature" is the feature-tag which indicates to the client that the fictional Funky-Parameter field is required. The relationship between "funky-feature" and Funky-Parameter is not communicated via the RTSP exchange, since that relationship is an immutable property of "funky-feature" and thus should not be transmitted with every exchange. Proxies and other intermediary devices SHALL ignore this header. If a particular extension requires that intermediate devices support it, the extension should be tagged in the Proxy-Require field instead (see Section 16.35). See discussion in the proxies section (Section 17.1) about when to consider that a feature requires proxy Schulzrinne, et al. Expires May 7, 2009 [Page 121] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 support. 16.43. RTP-Info The RTP-Info response-header field is used to set RTP-specific parameters in the PLAY response. For streams using RTP as transport protocol the RTP-Info header SHOULD be part of a 200 response to PLAY. The exclusion of the RTP-Info in a PLAY response for RTP transported media will result in that a client needs to synchronize the media streams using RTCP. This may have negative impact as the RTCP can be lost, and does not need to be particulary timely in their arrival. Also functionality as informing the client from which packet a seek has occurred is affected. The RTP-Info MAY also be included in SETUP responses to provide synchronization information when changing transport parameters, see Section 13.3. The header can carry the following parameters: url: Indicates the stream URI which for which the following RTP parameters correspond, this URI MUST be the same used in the SETUP request for this media stream. Any relative URI SHALL use the Request-URI as base URI. This parameter SHALL be present. ssrc: The Synchronization source (SSRC) that the RTP timestamp and sequence number provide applies to. This parameter SHALL be present. seq: Indicates the sequence number of the first packet of the stream that is direct result of the request. This allows clients to gracefully deal with packets when seeking. The client uses this value to differentiate packets that originated before the seek from packets that originated after the seek. Note that a client may not receive the packet with the expressed sequence number, and instead packets with a higher sequence number, due to packet loss or reordering. This parameter is RECOMMENDED to be present. rtptime: SHALL indicate the RTP timestamp value corresponding to the start time value in the Range response header, or if not explicitly given the implied start point. The client uses this value to calculate the mapping of RTP time to NPT or other media timescale. This parameter SHOULD be present to ensure Schulzrinne, et al. Expires May 7, 2009 [Page 122] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 inter-media synchronization is achieved. There exist no requirement that any received RTP packet will have the same RTP timestamp value as the one in the parameter used to establish synchronization. A mapping from RTP timestamps to NTP timestamps (wall clock) is available via RTCP. However, this information is not sufficient to generate a mapping from RTP timestamps to media clock time (NPT, etc.). Furthermore, in order to ensure that this information is available at the necessary time (immediately at startup or after a seek), and that it is delivered reliably, this mapping is placed in the RTSP control channel. In order to compensate for drift for long, uninterrupted presentations, RTSP clients should additionally map NPT to NTP, using initial RTCP sender reports to do the mapping, and later reports to check drift against the mapping. Example: Range:npt=3.25-15 RTP-Info:url="rtsp://example.com/foo/audio" ssrc=0A13C760:seq=45102; rtptime=12345678,url="rtsp://example.com/foo/video" ssrc=9A9DE123:seq=30211;rtptime=29567112 Lets assume that Audio uses a 16kHz RTP timestamp clock and Video a 90kHz RTP timestamp clock. Then the media synchronization is depicted in the following way. NPT 3.0---3.1---3.2-X-3.3---3.4---3.5---3.6 Audio PA A Video V PV X: NPT time value = 3.25, from Range header. A: RTP timestamp value for Audio from RTP-Info header (12345678). V: RTP timestamp value for Video from RTP-Info header (29567112). PA: RTP audio packet carrying an RTP timestamp of 12344878. Which corresponds to NPT = (12344878 - A) / 16000 + 3.25 = 3.2 PV: RTP video packet carrying an RTP timestamp of 29573412. Which corresponds to NPT = (29573412 - V) / 90000 + 3.25 = 3.32 16.44. Scale A scale value of 1 indicates normal play at the normal forward viewing rate. If not 1, the value corresponds to the rate with respect to normal viewing rate. For example, a ratio of 2 indicates twice the normal viewing rate ("fast forward") and a ratio of 0.5 indicates half the normal viewing rate. In other words, a ratio of 2 has normal play time increase at twice the wallclock rate. For every Schulzrinne, et al. Expires May 7, 2009 [Page 123] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 second of elapsed (wallclock) time, 2 seconds of content will be delivered. A negative value indicates reverse direction. For certain media transports this may require certain considerations to work consistent, see Appendix C.1 for description on how RTP handles this. Unless requested otherwise by the Speed parameter, the data rate SHOULD NOT be changed. Implementation of scale changes depends on the server and media type. For video, a server may, for example, deliver only key frames or selected key frames. For audio, for example, it may time-scale the audio while preserving pitch or, less desirably, deliver fragments of audio. The server should try to approximate the viewing rate, but may restrict the range of scale values that it supports. The response MUST contain the actual scale value chosen by the server. If the server does not implement the possibility to scale, it will not return a Scale header. A server supporting Scale operations for PLAY SHALL indicate this with the use of the "play.scale" feature- tags. When indicating a negative scale for a reverse playback, the Range header MUST indicate a decreasing range as described in Section 16.38. Example of playing in reverse at 3.5 times normal rate: Scale: -3.5 Range: npt=15-10 16.45. Seek-Style When a client sends a PLAY request with a Range header to perform a random access to the media, the client does not know if the server will pick the first media samples or the first random access point prior to the request range. Depending on use case, the client may have a strong preference. To express this preference and provide the client with information on how the server actually acted on that preference the Seek-Style header is defined. Seek-Style is a general header that MAY be included in any PLAY request to indicate the client's preference for any media stream that has random access properties. The server SHALL always include the header in any PLAY response for media with random access properties to indicate what policy was applied. A Server that receives a unknown Seek-Style policy SHALL ignore it and select the server default policy. Schulzrinne, et al. Expires May 7, 2009 [Page 124] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 This specification defines the following seek policies that may be requested: RAP: Random Access Point (RAP) is the behavior of requesting the server to locate the closest previous random access point that exist in the media aggregate and deliver from that. By requesting a RAP media quality will be the best possible as all media will be delivered from a point where full media state can be established in the media decoder. First-Prior: The first-prior policy will start delivery with the media unit that has a playout time first prior to the requested time. For discrete media that would only include media units that would still be rendered at the request time. For continous media that is media that will be render during the requested start time of the range. Next: The next media units after the provided start time of the range. For continous framed media that would mean the first next frame after the provided time. For discrete media the first unit that is to be rendered after the provided time. The main usage is for this case is when the client knows it has all media up to a certain point and would like to continue delivery so that a complete non-interrupted media playback can be achieved. Example of such scenarios include switching from a broadcast/multicast delivery to a unicast based delivery. This policy SHALL only be used on the client's explicit request. Please note that these expressed preferences exist for optimizing the startup time or the media quality. The "Next" policy breaks the normal definition of the Range header to enable a client to request media with minimal overlap, although some may still occur for aggregated sessions. RAP and First-Prior both fulfill the requirement of providing media from the requested range and forward. However, unless RAP is used, the media quality for many media codecs using predictive methods can be severly degraded unless additional data is available as, for example, already buffered, or through other side channels. 16.46. Speed The Speed request-header field requests the server to deliver data to the client at a particular speed, contingent on the server's ability and desire to serve the media stream at the given speed. Implementation by the server is OPTIONAL. The default is the bit rate of the stream. The parameter value is expressed as a decimal ratio, e.g., a value of Schulzrinne, et al. Expires May 7, 2009 [Page 125] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 2.0 indicates that data is to be delivered twice as fast as normal. A speed of zero is invalid. All speeds may not be possible to support. Therefore the actual used speed MUST be included in the response. The lack of a response header is indication of lack of support from the server of this functionality. Support of the speed functionality are indicated by the "play.speed" feature-tag. Example: Speed: 2.5 Use of this field changes the bandwidth used for data delivery. It is meant for use in specific circumstances where preview of the presentation at a higher or lower rate is necessary. Implementors should keep in mind that bandwidth for the session may be negotiated beforehand (by means other than RTSP), and therefore re-negotiation may be necessary. When data is delivered over UDP, it is highly recommended that means such as RTCP be used to track packet loss rates. If the data transport is performed over non-dedicated best- effort networks the sender is required to perform congestion control of the stream(s). This can result in that the communicated speed is impossible to maintain. 16.47. Server See [H14.38], however the header syntax is corrected in Section 20.2.3. 16.48. Session The Session request-header and response-header field identifies an RTSP session. An RTSP session is created by the server as a result of a successful SETUP request and in the response the session identifier is given to the client. The RTSP session exist until destroyed by a TEARDOWN or timed out by the server. The session identifier is chosen by the server (see Section 4.3) and MUST be returned in the SETUP response. Once a client receives a session identifier, it SHALL be included in any request related to that session. This means that the Session header MUST be included in a request using the following methods: PLAY, PAUSE, and TEARDOWN, and MAY be included in SETUP, OPTIONS, SET_PARAMETER, GET_PARAMETER, and REDIRECT, and SHALL NOT be included in DESCRIBE. In an RTSP response the session header SHALL be included in methods, SETUP, PLAY, and PAUSE, and MAY be included in methods, TEARDOWN, and REDIRECT, and if included in the request of the following methods it SHALL also be included in the response, OPTIONS, GET_PARAMETER, and SET_PARAMETER, and SHALL NOT be included in DESCRIBE. Schulzrinne, et al. Expires May 7, 2009 [Page 126] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Note that a session identifier identifies an RTSP session across transport sessions or connections. RTSP requests for a given session can use different URIs (Presentation and media URIs). Note, that there are restrictions depending on the session which URIs that are acceptable for a given method. However, multiple "user" sessions for the same URI from the same client will require use of different session identifiers. The session identifier is needed to distinguish several delivery requests for the same URI coming from the same client. The response 454 (Session Not Found) SHALL be returned if the session identifier is invalid. 16.49. Supported The Supported header field enumerates all the extensions supported by the client or server using feature tags. The header carries the extensions supported by the message sending entity. The Supported header MAY be included in any request. When present in a request, the receiver MUST respond with its corresponding Supported header. Note, also in 4xx and 5xx responses is the supported header included. The Supported header field contains a list of feature-tags, described in Section 4.7, that are understood by the client or server. Example: C->S: OPTIONS rtsp://example.com/ RTSP/2.0 Supported: foo, bar, blech User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK Supported: bar, blech, baz 16.50. Timestamp The Timestamp general-header field describes when the agent sent the request. The value of the timestamp is of significance only to the agent and may use any timescale. The responding agent MUST echo the exact same value and MAY, if it has accurate information about this, add a floating point number indicating the number of seconds that has elapsed since it has received the request. The timestamp is used by the agent to compute the round-trip time to the responding agent so that it can adjust the timeout value for retransmissions. It also resolves retransmission ambiguities for unreliable transport of RTSP. Schulzrinne, et al. Expires May 7, 2009 [Page 127] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.51. Transport The Transport request and response header field indicates which transport protocol is to be used and configures its parameters such as destination address, compression, multicast time-to-live and destination port for a single stream. It sets those values not already determined by a presentation description. A Transport request header field MAY contain a list of transport options acceptable to the client, in the form of multiple transport specification entries. Transport specifications are comma separated, listed in decreasing order of preference. Parameters may be added to each transport specififcation, separated by a semicolon. The server MUST return a Transport response-header field in the response to indicate the values actually chosen if any. If not transport specification is supported no transport header is returned and the request SHALL be responded using the status code 461 (Unsupported Transport) (Section 15.4.13). In case more than one transport specification was present in the request, the server MUST return the single (transport-spec) which was actually chosen if any. The number of transport-spec entries is expected to be limited as the client will get guidance on what configurations that are possible from the presentation description. The Transport header field MAY also be used in subsequent SETUP requests to change transport parameters. A server MAY refuse to change parameters of an existing stream. A transport specification may only contain one of any given parameter within it. Parameters MAY be given in any order. Additionally, it may only contain either of the unicast or the multicast transport type parameter. All parameters needs to be understood in a transport specification, if not the transport specification SHALL be ignored. RTSP proxies of any type that uses or modifies the transport specification, e.g. acces proxy or security proxy, SHALL remove specifications with unknown parameters before forwarding the RTSP message. If that result in no remaing transport specification the proxy shall send a 461 (Unsupported Transport) (Section 15.4.13) response without any Transport header. The Transport header field is restricted to describing a single media stream. (RTSP can also control multiple streams as a single entity.) Making it part of RTSP rather than relying on a multitude of session description formats greatly simplifies designs of firewalls. The general syntax for the transport specifier is a list of slash separated tokens: Schulzrinne, et al. Expires May 7, 2009 [Page 128] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Value1/Value2/Value3... Which for RTP transports take the form: RTP/profile/lower-transport. The default value for the "lower-transport" parameters is specific to the profile. For RTP/AVP, the default is UDP. There are two different methods for how to specify where the media should be delivered for unicast transport: dest_addr: The presence of this parameter and its values indicates the destination address or addresses (host address and port pairs for IP flows) necessary for the media transport. No dest_addr: The lack of the dest_addr parameter indicates that the server SHALL send media to same address for which the RTSP messages originates. Does not work for transports requiring explicitly given destination ports. The choice of method for indicating where the media is to be delivered depends on the use case. In some case the only allowed method will be to use no explicit address indication and have the server deliver media to the source of the RTSP messages. For Multicast there is several methods for specifying addresses but they are different in how they work compared with unicast: dest_addr with client picked address: The address and relevant parameters like TTL (scope) for the actual multicast group to deliver the media to. There are security implications (Section 21) with this method that needs to be addressed if using this method because a RTSP server can be used as a DoS attacker on a existing multicast group. dest_addr using Session Decription Information: The information included in the transport header can all be comming from the session description, e.g. the SDP c= and m= line. This mitigates some of the security issues of the previous methods as it is the session provider that picks the multicast group and scope. The client SHALL include the information if it is available in the session description. No dest_addr: The lack of an explicit multicast group request the server to decide the group address and its scope. For this to work the server needs to have a context about what scope that works. This method is currently under specified. An RTSP proxy will need to take care. If the media is not desired to Schulzrinne, et al. Expires May 7, 2009 [Page 129] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 be routed through the proxy, the proxy will need to introduce the destination indication. Below are the configuration parameters associated with transport: General parameters: unicast / multicast: This parameter is a mutually exclusive indication of whether unicast or multicast delivery will be attempted. One of the two values MUST be specified. Clients that are capable of handling both unicast and multicast transmission needs to indicate such capability by including two full transport-specs with separate parameters for each. layers: The number of multicast layers to be used for this media stream. The layers are sent to consecutive addresses starting at the dest_addr address. If the parameter is not included, it defaults to a single layer. dest_addr: A general destination address parameter that can contain one or more address specifications. Each combination of Protocol/Profile/Lower Transport needs to have the format and interpretation of its address specification defined. For RTP/ AVP/UDP and RTP/AVP/TCP, the address specification is a tuple containing a host address and port. Note, only a single destination entity per transport spec is intended. The usage of multiple destination to distribute a single media to multiple entities is unspecified. The client originating the RTSP request MAY specify the destination address of the stream recipient with the host address part of the tuple. When the destination address is specified, the recipient may be a different party than the originator of the request. To avoid becoming the unwitting perpetrator of a remote-controlled denial-of-service attack, a server MUST perform security checks (see Section 21.1) and SHOULD log such attempts before allowing the client to direct a media stream to a recipient address not chosen by the server. Implementations cannot rely on TCP as reliable means of client identification. If the server does not allow the host address part of the tuple to be set, it SHALL return 463 (Destination Prohibited). The host address part of the tuple MAY be empty, for example ":58044", in cases when only destination port is desired to be specified. Responses to request including the Transport header with a dest_addr parameter SHOULD include the full destination address that is actually used by the server. The server MUST Schulzrinne, et al. Expires May 7, 2009 [Page 130] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 NOT remove address information present already in the request when responding unless the protocol requires it. src_addr: A general source address parameter that can contain one or more address specifications. Each combination of Protocol/ Profile/Lower Transport needs to have the format and interpretation of its address specification defined. For RTP/ AVP/UDP and RTP/AVP/TCP, the address specification is a tuple containing a host address and port. This parameter MUST be specified by the server if it transmits media packets from another address than the one RTSP messages are sent to. This will allow the client to verify source address and give it a destination address for its RTCP feedback packets if RTP is used. The address or addresses indicated in the src_addr parameter SHOULD be used both for sending and receiving of the media streams data packets. The main reasons are threefold: First, indicating the port and source address(s) lets the receiver know where from the packets is expected to originate. Secondly, traversal of NATs are greatly simplified when traffic is flowing symmetrically over a NAT binding. Thirdly, certain NAT traversal mechanisms, needs to know to which address and port to send so called "binding packets" from the receiver to the sender, thus creating a address binding in the NAT that the sender to receiver packet flow can use. This information may also be available through SDP. However, since this is more a feature of transport than media initialization, the authoritative source for this information should be in the SETUP response. mode: The mode parameter indicates the methods to be supported for this session. Valid values are PLAY and RECORD. If not provided, the default is PLAY. The RECORD value was defined in RFC 2326 and is in this specification unspecified but reserved. interleaved: The interleaved parameter implies mixing the media stream with the control stream in whatever protocol is being used by the control stream, using the mechanism defined in Section 14. The argument provides the channel number to be used in the $ statement and MUST be present. This parameter MAY be specified as a range, e.g., interleaved=4-5 in cases where the transport choice for the media stream requires it, e.g. for RTP with RTCP. The channel number given in the request are only a guidance from the client to the server on what channel number(s) to use. The server MAY set any valid channel number in the response. The declared channel(s) are Schulzrinne, et al. Expires May 7, 2009 [Page 131] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 bi-directional, so both end-parties MAY send data on the given channel. One example of such usage is the second channel used for RTCP, where both server and client sends RTCP packets on the same channel. This allows RTP/RTCP to be handled similarly to the way that it is done with UDP, i.e., one channel for RTP and the other for RTCP. Multicast-specific: ttl: multicast time-to-live for IPv4. When included in requests the value indicate the TTL value that the client request the server to use. In a response, the value actually being used by the server is returned. A server will need to consider what values that are reasonable and also the authority of the user to set this value. Corresponding function are not needed for IPv6 as the scoping is part of the address. RTP-specific: These parameters are MAY only be used if the media transport protocol is RTP. ssrc: The ssrc parameter, if included in a SETUP response, indicates the RTP SSRC [RFC3550] value(s) that will be used by the media server for RTP packets within the stream. It is expressed as an eight digit hexadecimal value. The ssrc parameter SHALL NOT be specified in requests. The functionality of specifying the ssrc parameter in a SETUP request is deprecated as it is incompatible with the specification of RTP in RFC 3550[RFC3550]. If the parameter is included in the Transport header of a SETUP request, the server MAY ignore it, and choose appropriate SSRCs for the stream. The server MAY set the ssrc parameter in the Transport header of the response. The parameters defined below MAY only be used if the media transport protocol if the lower-level transport is connection-oriented (such as TCP). However, these parameters MUST NOT be used when interleaving data over the RTSP control connection. setup: Clients use the setup parameter on the Transport line in a SETUP request, to indicate the roles it wishes to play in a TCP connection. This parameter is adapted from [RFC4145]. We discuss the use of this parameter in RTP/AVP/TCP non- Schulzrinne, et al. Expires May 7, 2009 [Page 132] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 interleaved transport in Appendix C.2.2; the discussion below is limited to syntactic issues. Clients may specify the following values for the setup parameter: ["active":] The client will initiate an outgoing connection. ["passive":] The client will accept an incoming connection. ["actpass":] The client is willing to accept an incoming connection or to initiate an outgoing connection. If a client does not specify a setup value, the "active" value is assumed. In response to a client SETUP request where the setup parameter is set to "active", a server's 2xx reply MUST assign the setup parameter to "passive" on the Transport header line. In response to a client SETUP request where the setup parameter is set to "passive", a server's 2xx reply MUST assign the setup parameter to "active" on the Transport header line. In response to a client SETUP request where the setup parameter is set to "actpass", a server's 2xx reply MUST assign the setup parameter to "active" or "passive" on the Transport header line. Note that the "holdconn" value for setup is not defined for RTSP use, and MUST NOT appear on a Transport line. connection: Clients use the setup parameter on the Transport line in a SETUP request, to indicate the SETUP request prefers the reuse of an existing connection between client and server (in which case the client sets the "connection" parameter to "existing"), or that the client requires the creation of a new connection between client and server (in which cast the client sets the "connection" parameter to "new"). Typically, clients use the "new" value for the first SETUP request for a URL, and "existing" for subsequent SETUP requests for a URL. If a client SETUP request assigns the "new" value to "connection", the server response MUST also assign the "new" value to "connection" on the Transport line. If a client SETUP request assigns the "existing" value to "connection", the server response MUST assign a value of "existing" or "new" to "connection" on the Transport line, at its discretion. The default value of "connection" is "existing", for all SETUP requests (initial and subsequent). Schulzrinne, et al. Expires May 7, 2009 [Page 133] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The combination of transport protocol, profile and lower transport needs to be defined. A number of combinations are defined in the Appendix C. Below is a usage example, showing a client advertising the capability to handle multicast or unicast, preferring multicast. Since this is a unicast-only stream, the server responds with the proper transport parameters for unicast. C->S: SETUP rtsp://example.com/foo/bar/baz.rm RTSP/2.0 CSeq: 302 Transport: RTP/AVP;multicast;mode="PLAY", RTP/AVP;unicast;dest_addr="192.0.2.5:3456"/ "192.0.2.5:3457";mode="PLAY" Accept-Ranges: NPT, SMPTE, UTC User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 302 Date: Thu, 23 Jan 1997 15:35:06 GMT Session: 47112344 Transport: RTP/AVP;unicast;dest_addr="192.0.2.5:3456"/ "192.0.2.5:3457";src_addr="192.0.2.224:6256"/ "192.0.2.224:6257";mode="PLAY" Accept-Ranges: NPT 16.52. Unsupported The Unsupported response-header field lists the features not supported by the server. In the case where the feature was specified via the Proxy-Require field (Section 16.35), if there is a proxy on the path between the client and the server, the proxy MUST send a response message with a status code of 551 (Option Not Supported). The request SHALL NOT be forwarded. See Section 16.42 for a usage example. 16.53. User-Agent See [H14.43] for explanation, however the syntax is clarified due to an error in RFC 2616. A Client SHOULD include this header in all RTSP messages it sends. 16.54. Vary See [H14.44]. Schulzrinne, et al. Expires May 7, 2009 [Page 134] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 16.55. Via See [H14.45]. 16.56. WWW-Authenticate See [H14.47]. Schulzrinne, et al. Expires May 7, 2009 [Page 135] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 17. Proxies RTSP Proxies are RTSP agents that sit in between a client and a server. A proxy can take on both the role as a client and as server depending on what it tries to accomplish. Proxies are also introduced for several different reasons and the below are often combined. Caching Proxy: This type of proxy is used to reduce the workload on servers and connections. By caching a presentation, both description and media streams the proxy can serve a client content without requesting it from the server once it has been cached and hasn't become stale. See the caching Section 18. This type of proxy is expected to also understand RTSP end- point functionality, i.e. functionality identified in the Require header in addition to what Proxy-Require demands. Translator Proxy: This type of proxy is used to ensure that a RTSP client get access to servers and content on an external network or using content encodings not supported by the client. The proxy performs the necessary translation of addresses, protocols or encodings. This type of proxy is expected to also understand RTSP end-point functionality, i.e. functionality identified in the Require header in addition to what Proxy- Require demands. Access Proxy: This type of proxy is used to ensure that a RTSP client get access to servers on an external network. Thus this proxy is placed on the border between two domains, e.g. a private address space and the public internet. The proxy performs the necessary translation, usually addresses. This type of proxies are required to redirect the media to themselves or a controlled gateway that perform the translation before the media can reach the client. Security Proxy: This type of proxy is used to help facilitate security functions around RTSP. For example when having a firewalled network, the security proxy request that the necessary pinholes in the firewall is opened when a client in the protected network want to access media streams on the external side.This proxy can also limit the clients access to certain type of content. This proxy can perform its function without redirecting the media between the server and client. However, in deployements with private address spaces this proxy is likely to be combined with the access proxy. Anyway, the functionality of this proxy is usually closely tied into understand all aspects of how the media transport. Schulzrinne, et al. Expires May 7, 2009 [Page 136] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Auditing Proxy: RTSP proxies can also provide network owners with a logging and audit point for RTSP sessions, e.g. for corporations that tracks their employees usage of the network. This type of proxy can perform its function without inserting itself or any other node in the media transport. This proxy type can also accept unknown methods as it doesn't interfere with the clients requests. All type of proxies can be used also when using secured communication with TLS as RTSP 2.0 allows the client to approve certificate chains used for connection establishment from a proxy, see Section 19.3.2. However that trust model may not be suitable for all type of deployment, and instead secured sessions do by-pass of the proxies. Access proxies SHOULD NOT be used in equipment like NATs and firewalls that aren't expected to be regularly maintained, like home or small office equipment. In these cases it is better to use the NAT traversal procedures defined for RTSP 2.0 [I-D.ietf-mmusic-rtsp-nat]. The reason for these recommendations is that any extensions of RTSP resulting in new media transport protocols or profiles, new parameters etc may fail in a proxy that isn't maintained. Thus resulting in blocking further development of RTSP and its usage. 17.1. Proxies and Protocol Extensions The existence of proxies must always be considered when developing new RTSP extensions. Most type of proxies will need to implement any new method to operate correct in the presence of that extension. New headers will be possible to introduce without being blocked by proxies not yet updated. However, it is important to consider if this header and its function is required to be understood by the proxy or can be forwarded. If the header needs to be understood a feature-tag representing the functionality needs to be included in the Proxy-Require header. Below are guidelines for analysis if the header needs to be understood. The transport header and its parameters also shows that headers that are extensible and requires correct interpretation in the proxy also requires handling rules. When defining a new RTSP header it needs to be considered if RTSP proxies are required to understand them to achieve correct functionality. Determining this is not easy as the functionality for proxies are widely varied as can be understood from the above list of functionality. When evaluating this one can dived the functionality into three main categories: Schulzrinne, et al. Expires May 7, 2009 [Page 137] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Media modifying: The caching and translator proxies are modifying the actual media and therefore needs to understand also request directed to the server that affects how the media is rendered. Thus this type of proxies needs to also understand the server side functionality. Transport modifying: The access and the security proxy both need to understand the how the transport is performed, either for opening pinholes or to translate the outer headers, e.g. IP and UDP. Non-modifying: The audit proxy is special in that it do not modify the messages in other ways than to insert the Via header. That makes it possible for this type to forward RTSP message that contains different type of unknown methods, headers or header parameters. Based on the above classification one should evaluate if ones functionality requires the Transport modifying type of proxies to understand it or not. Schulzrinne, et al. Expires May 7, 2009 [Page 138] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 18. Caching In HTTP, response-request pairs are cached. RTSP differs significantly in that respect. Responses are not cacheable, with the exception of the presentation description returned by DESCRIBE. (Since the responses for anything but DESCRIBE and GET_PARAMETER do not return any data, caching is not really an issue for these requests.) However, it is desirable for the continuous media data, typically delivered out-of-band with respect to RTSP, to be cached, as well as the session description. On receiving a SETUP or PLAY request, a proxy ascertains whether it has an up-to-date copy of the continuous media content and its description. It can determine whether the copy is up-to-date by issuing a SETUP or DESCRIBE request, respectively, and comparing the Last-Modified header with that of the cached copy. If the copy is not up-to-date, it modifies the SETUP transport parameters as appropriate and forwards the request to the origin server. Subsequent control commands such as PLAY or PAUSE then pass the proxy unmodified. The proxy delivers the continuous media data to the client, while possibly making a local copy for later reuse. The exact behavior allowed to the cache is given by the cache-response directives described in Section 16.10. A cache MUST answer any DESCRIBE requests if it is currently serving the stream to the requestor, as it is possible that low-level details of the stream description may have changed on the origin-server. Note that an RTSP cache, unlike the HTTP cache, is of the "cut- through" variety. Rather than retrieving the whole resource from the origin server, the cache simply copies the streaming data as it passes by on its way to the client. Thus, it does not introduce additional latency. To the client, an RTSP proxy cache appears like a regular media server, to the media origin server like a client. Just as an HTTP cache has to store the content type, content language, and so on for the objects it caches, a media cache has to store the presentation description. Typically, a cache eliminates all transport-references (that is, e.g. multicast information) from the presentation description, since these are independent of the data delivery from the cache to the client. Information on the encodings remains the same. If the cache is able to translate the cached media data, it would create a new presentation description with all the encoding possibilities it can offer. Schulzrinne, et al. Expires May 7, 2009 [Page 139] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 19. Security Framework The RTSP security framework consists of two high level components: the pure authentication mechanisms based on HTTP authentication, and the transport protection based on TLS, which is independent of RTSP. Because of the similarity in syntax and usage between RTSP servers and HTTP servers, the security for HTTP is re-used to a large extent. 19.1. RTSP and HTTP Authentication RTSP and HTTP share common authentication schemes, and thus follow the same usage guidelines as specified in[RFC2617] and also in [H15]. Servers SHOULD implement both basic and digest [RFC2617] authentication. Client SHALL implement both basic and digest authentication [RFC2617] so that Server who requires the client to authenticate can trust that the capability is present. It should be stressed that using the HTTP authentication alone does not provide full control message security. Therefore, in environments requiring tighter security for the control messages, TLS SHOULD be used, see Section 19.2. 19.2. RTSP over TLS RTSP SHALL follow the same guidelines with regards to TLS [RFC5246] usage as specified for HTTP, see [RFC2818]. RTSP over TLS is separated from unsecured RTSP both on URI level and port level. Instead of using the "rtsp" scheme identifier in the URI, the "rtsps" scheme identifier MUST be used to signal RTSP over TLS. If no port is given in a URI with the "rtsps" scheme, port 322 SHALL be used for TLS over TCP/IP. When a client tries to setup an insecure channel to the server (using the "rtsp" URI), and the policy for the resource requires a secure channel, the server SHALL redirect the client to the secure service by sending a 301 redirect response code together with the correct Location URI (using the "rtsps" scheme). A user or client MAY upgrade a non secured URI to a secured by changing the scheme from "rtsp" to "rtsps". A server implementing support for "rtsps" SHALL allow this. It should be noted that TLS allows for mutual authentication (when using both server and client certificates). Still, one of the more common way TLS is used is to only provide server side authentication (often to avoid client certificates). TLS is then used in addition to HTTP authentication, providing transport security and server authentication, while HTTP Authentication is used to authenticate the client. Schulzrinne, et al. Expires May 7, 2009 [Page 140] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 RTSP includes the possibility to keep a TCP session up between the client and server, throughout the RTSP session lifetime. It may be convenient to keep the TCP session, not only to save the extra setup time for TCP, but also the extra setup time for TLS (even if TLS uses the resume function, there will be almost two extra roundtrips). Still, when TLS is used, such behavior introduces extra active state in the server, not only for TCP and RTSP, but also for TLS. This may increase the vulnerability to DoS attacks. In addition to these recommendations, Section 19.3 gives further recommendations of TLS usage with proxies. 19.3. Security and Proxies The nature of a proxy is often to act as a "man-in-the-middle", while security is often about preventing the existence of a "man-in-the- middle". This section provides clients with the possibility to use proxies even when applying secure transports (TLS) between the RTSP agents. The TLS proxy mechanism allows for server and proxy identification using certificates. However, the client can not be identified based on certificates. The client needs to select between using the procedure specified below or using a TLS connection directly (by-passing any proxies) to the server. The choice may be dependent on policies. There are basically two categories of proxies, the transparent proxies (of which the client is not aware) and the non-transparent proxies (of which the client is aware). An infrastructure based on proxies requires that the trust model is such that both client and servers can trust the proxies to handle the RTSP messages correctly. To be able to trust a proxy, the client and server also needs to be aware of the proxy. Hence, transparent proxies cannot generally be seen as trusted and will not work well with security (unless they work only at transport layer). In the rest of this section any reference to proxy will be to a non-transparent proxy, which inspects or manipulate the RTSP messages. HTTP Authentication is built on the assumption of proxies and can provide user-proxy authentication and proxy-proxy/server authentication in addition to the client-server authentication. When TLS is applied and a proxy is used, the client will connect to the proxy's address when connecting to any RTSP server. This implies that for TLS, the client will authenticate the proxy server and not the end server. Note that when the client checks the server certificate in TLS, it MUST check the proxy's identity (URI or possibly other known identity) against the proxy's identity as presented in the proxy's Certificate message. Schulzrinne, et al. Expires May 7, 2009 [Page 141] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The problem is that for a proxy accepted by the client, the proxy needs to be provided information on which grounds it should accept the next-hop certificate. Both the proxy and the user may have rules for this, and the user have the possibility to select the desired behavior. To handle this case, the Accept-Credentials header (See Section 16.2) is used, where the client can force the proxy/proxies to relay back the chain of certificates used to authenticate any intermediate proxies as well as the server. Given the assumption that the proxies are viewed as trusted, it gives the user a possibility to enforce policies to each trusted proxy of whether it should accept the next entity in the chain. A proxy MUST use TLS for the next hop if the RTSP request includes a "rtsps" URI. TLS MAY be applied on intermediate links (e.g. between client and proxy, or between proxy and proxy), even if the resource and the end server does not require to use it. The proxy SHALL when initiating the next hop TLS connection use the incomming TLS connections CipherSuite list, only modified by removing any cipher suits that the proxy does not support. In case a proxy fails to establish a TLS connection due to cipher suite mismatch between proxy and next hop proxy or server, this is indicated using error code 472 (Failure to establish secure connection). 19.3.1. Accept-Credentials The Accept-Credentials header can be used by the client to distribute simple authorization policies to intermediate proxies. The client includes the Accept-Credentials header to dictate how the proxy treats the server/next proxy certificate. There are currently three methods defined: Any, which means that the proxy (or proxies) SHALL accept whatever certificate presented. This is of course not a recommended option to use, but may be useful in certain circumstances (such as testing). Proxy, which means that the proxy (or proxies) MUST use its own policies to validate the certificate and decide whether to accept it or not. This is convenient in cases where the user has a strong trust relation with the proxy. Reason why a strong trust relation may exist are; personal/company proxy, proxy has a out-of-band policy configuration mechanism. User, which means that the proxy (or proxies) MUST send credential information about the next hop to the client for authorization. The client can then decide whether the proxy should accept the certificate or not. See Section 19.3.2 for further details. Schulzrinne, et al. Expires May 7, 2009 [Page 142] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 If the Accept-Credentials header is not included in the RTSP request from the client, then the "Proxy" method SHALL be used as default. If an other method than the "Proxy" is to be used, then the Accept- Credentials header SHALL be included in all of the RTSP request from the client. This is because it cannot be assumed that the proxy always keeps the TLS state or the users previously preference between different RTSP messages (in particular if the time interval between the messages is long). With the "Any" and "Proxy" methods the proxy will apply the policy as defined for respectively method. If the policy do not accept the credentials of the next hop, the entity SHALL respond with a message using status code 471 (Connection Credentials not accepted). An RTSP request in the direction server to client MUST NOT include the Accept-Credential header. As for the non-secured communication, the possibility for these request depends on the presence of a client established connection. However if the server to client request is in relation to a session established over a TLS secured channel, if MUST be sent in a TLS secured connection. That secured connection MUST also be the one used by the last client to server request. If no such transport connection exist at the time when the server desire to send the request, it silently fails. Further policies MAY be defined and registered, but should be done so with caution. 19.3.2. User approved TLS procedure For the "User" method each proxy MUST perform the the following procedure for each RTSP request: o Setup the TLS session to the next hop if not already present (i.e. run the TLS handshake, but do not send the RTSP request). o Extract the peer certificate chain for the TLS session. o Check if a matching identity and hash of the peer certificate is present in the Accept-Credentials header. If present, send the message to the next hop, and conclude these procedures. If not, go to the next step. o The proxy responds to the RTSP request with a 470 or 407 response code. The 407 response code MAY be used when the proxy requires both user and connection authorization from user or client. In this message the proxy SHALL include a Connection-Credentials header, see Section 16.12 with the next hop's identity and certificate. Schulzrinne, et al. Expires May 7, 2009 [Page 143] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The client MUST upon receiving a 470 or 407 response with Connection- Credentials header take the decision on whether to accept the certificate or not (if it cannot do so, the user SHOULD be consulted). If the certificate is accepted, the client has to again send the RTSP request. In that request the client has to include the Accept-Credentials header including the hash over the DER encoded certificate for all trusted proxies in the chain. Example: C->P: SETUP rtsps://test.example.org/secret/audio RTSP/2.0 CSeq: 2 Transport: RTP/AVP;unicast;dest_addr="192.0.2.5:4588"/ "192.0.2.5:4589" Accept-Ranges: NPT, SMPTE, UTC Accept-Credentials: User P->C: RTSP/2.0 470 Connection Authorization Required CSeq: 2 Connection-Credentials: "rtsps://test.example.org"; MIIDNTCCAp... C->P: SETUP rtsps://test.example.org/secret/audio RTSP/2.0 CSeq: 2 Transport: RTP/AVP;unicast;dest_addr="192.0.2.5:4588"/ "192.0.2.5:4589" Accept-Credentials: User "rtsps://test.example.org";sha-256; dPYD7txpoGTbAqZZQJ+vaeOkyH4= Accept-Ranges: NPT, SMPTE, UTC P->S: SETUP rtsps://test.example.org/secret/audio RTSP/2.0 CSeq: 2 Transport: RTP/AVP;unicast;dest_addr="192.0.2.5:4588"/ "192.0.2.5:4589" Via: RTSP/2.0 proxy.example.org Accept-Credentials: User "rtsps://test.example.org";sha-256; dPYD7txpoGTbAqZZQJ+vaeOkyH4= Accept-Ranges: NPT, SMPTE, UTC One implication of this process is that the connection for secured RTSP messages may take significantly more round-trip times for the first message. An complete extra message exchange between the proxy connecting to the next hop and the client results because of the process for approval for each hop. However after the first message exchange the remaining message should not be delayed, if each message contains the chain of proxies that the requestor accepts. The procedure of including the credentials in each request rather than building state in each proxy, avoids the need for revocation procedures. Schulzrinne, et al. Expires May 7, 2009 [Page 144] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 20. Syntax The RTSP syntax is described in an Augmented Backus-Naur Form (ABNF) as defined in RFC 5234 [RFC5234]. It uses the basic definitions present in RFC 5234. Please note that ABNF strings, e.g. "Accept", are case insensitive as specified in section 2.3 of RFC 5234. 20.1. Base Syntax RTSP header field values can be folded onto multiple lines if the continuation line begins with a space or horizontal tab. All linear white space, including folding, has the same semantics as SP. A recipient MAY replace any linear white space with a single SP before interpreting the field value or forwarding the message downstream. This is intended to behave exactly as HTTP/1.1 as described in RFC 2616 [RFC2616]. The SWS construct is used when linear white space is optional, generally between tokens and separators. To separate the header name from the rest of value, a colon is used, which, by the above rule, allows whitespace before, but no line break, and whitespace after, including a linebreak. The HCOLON defines this construct. OCTET = %x00-FF ; any 8-bit sequence of data CHAR = %x01-7F ; any US-ASCII character (octets 1 - 127) UPALPHA = %x41-5A ; any US-ASCII uppercase letter "A".."Z" LOALPHA = %x61-7A ;any US-ASCII lowercase letter "a".."z" ALPHA = UPALPHA / LOALPHA DIGIT = %x30-39 ; any US-ASCII digit "0".."9" CTL = %x00-1F / %x7F ; any US-ASCII control character ; (octets 0 - 31) and DEL (127) CR = %x0D ; US-ASCII CR, carriage return (13 LF = %x0A ; US-ASCII LF, linefeed (10) SP = %x20 ; US-ASCII SP, space (32) HT = %x09 ; US-ASCII HT, horizontal-tab (9) DQ = %x22 ; US-ASCII double-quote mark (34) BACKSLASH = %x5C ; US-ASCII backslash (92) CRLF = CR LF Schulzrinne, et al. Expires May 7, 2009 [Page 145] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 LWS = [CRLF] 1*( SP / HT ) SWS = [LWS] ; sep whitespace HCOLON = *( SP / HT ) ":" SWS TEXT = %x20-7E / %x80-FF ; any OCTET except CTLs tspecials = "(" / ")" / "<" / ">" / "@" / "," / ";" / ":" / BACKSLASH / DQ / "/" / "[" / "]" / "?" / "=" / "{" / "}" / SP / HT token = 1*(%x21 / %x23-27 / %x2A-2B / %x2D-2E / %x30-39 / %x41-5A / %x5E-7A / %x7C / %x7E) ; 1* quoted-string = ( DQ *qdtext DQ ) qdtext = %x20-21 / %x23-7E / %x80-FF ; any TEXT except <"> quoted-pair = BACKSLASH CHAR ctext = %x20-27 / %x2A-7E / %x80-FF ; any OCTET except CTLs, "(" and ")" generic-param = token [ EQUAL gen-value ] gen-value = token / host / quoted-string safe = "$" / "-" / "_" / "." / "+" extra = "!" / "*" / "'" / "(" / ")" / "," rtsp-extra = "!" / "*" / "'" / "(" / ")" HEX = DIGIT / "A" / "B" / "C" / "D" / "E" / "F" / "a" / "b" / "c" / "d" / "e" / "f" LHEX = DIGIT / %x61-66 ;lowercase a-f reserved = ";" / "/" / "?" / ":" / "@" / "&" / "=" unreserved = ALPHA / DIGIT / safe / extra rtsp-unreserved = ALPHA / DIGIT / safe / rtsp-extra base64 = *base64-unit [base64-pad] base64-unit = 4base64-char base64-pad = (2base64-char "==") / (3base64-char "=") base64-char = ALPHA / DIGIT / "+" / "/" Schulzrinne, et al. Expires May 7, 2009 [Page 146] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 SLASH = SWS "/" SWS ; slash EQUAL = SWS "=" SWS ; equal LPAREN = SWS "(" SWS ; left parenthesis RPAREN = SWS ")" SWS ; right parenthesis COMMA = SWS "," SWS ; comma SEMI = SWS ";" SWS ; semicolon COLON = SWS ":" SWS ; colon LDQUOT = SWS DQ ; open double quotation mark RDQUOT = DQ SWS ; close double quotation mark RAQUOT = ">" SWS ; right angle quote LAQUOT = SWS "<" ; left angle quote TEXT-UTF8char = %x21-7E / UTF8-NONASCII UTF8-NONASCII = %xC0-DF 1UTF8-CONT / %xE0-EF 2UTF8-CONT / %xF0-F7 3UTF8-CONT / %xF8-FB 4UTF8-CONT / %xFC-FD 5UTF8-CONT UTF8-CONT = %x80-BF FLOAT = ["-"] 1*39DIGIT ["." 1*46DIGIT] POS-FLOAT = 1*39DIGIT ["." 1*46DIGIT] 20.2. RTSP Protocol Definition 20.2.1. Generic Protocol elements Schulzrinne, et al. Expires May 7, 2009 [Page 147] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 RTSP-IRI = schemes ":" IRI-rest IRI-rest = ihier-part [ "?" iquery ] [ "#" ifragment ] ihier-part = "//" iauthority ipath-abempty RTSP-IRI-ref = RTSP-IRI / irelative-ref irelative-ref = irelative-part [ "?" iquery ] [ "#" ifragment ] irelative-part = "//" iauthority ipath-abempty / ipath-absolute / ipath-noscheme / ipath-empty iauthority = < As defined in RFC 3987> ipath = ipath-abempty ; begins with "/" or is empty / ipath-absolute ; begins with "/" but not "//" / ipath-noscheme ; begins with a non-colon segment / ipath-rootless ; begins with a segment / ipath-empty ; zero characters ipath-abempty = *( "/" isegment ) ipath-absolute = "/" [ isegment-nz *( "/" isegment ) ] ipath-noscheme = isegment-nz-nc *( "/" isegment ) ipath-rootless = isegment-nz *( "/" isegment ) ipath-empty = 0 isegment = *ipchar [";" *ipchar] isegment-nz = 1*ipchar [";" *ipchar] / ";" *ipchar isegment-nz-nc = (1*ipchar-nc [";" *ipchar-nc]) / ";" *ipchar-nc ; non-zero-length segment without any colon ":" ipchar = iunreserved / pct-encoded / sub-delims / ":" / "@" ipchar-nc = iunreserved / pct-encoded / sub-delims / "@" iquery = < As defined in RFC 3987> ifragment = < As defined in RFC 3987> iunreserved = < As defined in RFC 3987> pct-encoded = < As defined in RFC 3987> Schulzrinne, et al. Expires May 7, 2009 [Page 148] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 RTSP-URI = schemes ":" URI-rest RTSP-URI-Ref = RTSP-URI / RTSP-Relative schemes = "rtsp" / "rtsps" / scheme scheme = < As defined in RFC 3986> URI-rest = hier-part [ "?" query ] hier-part = "//" authority path-abempty RTSP-Relative = relative-part [ "?" query ] relative-part = "//" authority path-abempty / path-absolute / path-noscheme / path-empty authority = < As defined in RFC 3986> query = < As defined in RFC 3986> path = path-abempty ; begins with "/" or is empty / path-absolute ; begins with "/" but not "//" / path-noscheme ; begins with a non-colon segment / path-rootless ; begins with a segment / path-empty ; zero characters path-abempty = *( "/" segment ) path-absolute = "/" [ segment-nz *( "/" segment ) ] path-noscheme = segment-nz-nc *( "/" segment ) path-rootless = segment-nz *( "/" segment ) path-empty = 0 segment = *pchar [";" *pchar] segment-nz = ( 1*pchar [";" *pchar]) / (";" *pchar) segment-nz-nc = ( 1*pchar-nc [";" *pchar-nc]) / (";" *pchar-nc) ; non-zero-length segment without any colon ":" pchar = unreserved / pct-encoded / sub-delims / ":" / "@" pchar-nc = unreserved / pct-encoded / sub-delims / "@" sub-delims = "!" / "$" / "&" / "'" / "(" / ")" / "*" / "+" / "," / "=" Schulzrinne, et al. Expires May 7, 2009 [Page 149] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 smpte-range = smpte-type "=" smpte-range-spec ; See section 3.4 smpte-range-spec = ( smpte-time "-" [ smpte-time ] ) / ( "-" smpte-time ) smpte-type = "smpte" / "smpte-30-drop" / "smpte-25" / smpte-type-extension ; other timecodes may be added smpte-type-extension = token smpte-time = 1*2DIGIT ":" 1*2DIGIT ":" 1*2DIGIT [ ":" 1*2DIGIT [ "." 1*2DIGIT ] ] npt-range = "npt=" npt-range-spec npt-range-spec = ( npt-time "-" [ npt-time ] ) / ( "-" npt-time ) npt-time = "now" / npt-sec / npt-hhmmss npt-sec = 1*DIGIT [ "." *DIGIT ] npt-hhmmss = npt-hh ":" npt-mm ":" npt-ss [ "." *DIGIT ] npt-hh = 1*DIGIT ; any positive number npt-mm = 1*2DIGIT ; 0-59 npt-ss = 1*2DIGIT ; 0-59 utc-range = "clock=" utc-range-spec utc-range-spec = ( utc-time "-" [ utc-time ] ) / ( "-" utc-time ) utc-time = utc-date "T" utc-clock "Z" utc-date = 8DIGIT utc-clock = 6DIGIT [ "." fraction ] fraction = 1*DIGIT feature-tag = token session-id = 1*256( ALPHA / DIGIT / safe ) extension-header = header-name HCOLON header-value header-name = token header-value = *(TEXT-UTF8char / UTF8-CONT / LWS) 20.2.2. Message Syntax Schulzrinne, et al. Expires May 7, 2009 [Page 150] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 RTSP-message = Request / Response ; RTSP/2.0 messages Request = Request-Line *((general-header / request-header / entity-header) CRLF) CRLF [ message-body ] Response = Status-Line *((general-header / response-header / entity-header) CRLF) CRLF [ message-body ] Request-Line = Method SP Request-URI SP RTSP-Version CRLF Status-Line = RTSP-Version SP Status-Code SP Reason-Phrase CRLF Method = "DESCRIBE" / "GET_PARAMETER" / "OPTIONS" / "PAUSE" / "PLAY" / "PLAY_NOTIFY" / "REDIRECT" / "SETUP" / "SET_PARAMETER" / "TEARDOWN" / extension-method extension-method = token Request-URI = "*" / RTSP-URI RTSP-Version = "RTSP/" 1*DIGIT "." 1*DIGIT message-body = 1*OCTET Status-Code = "100" ; Continue / "200" ; OK / "300" ; Multiple Choices / "301" ; Moved Permanently / "302" ; Found / "303" ; See Other / "304" ; Not Modified / "305" ; Use Proxy / "400" ; Bad Request / "401" ; Unauthorized Schulzrinne, et al. Expires May 7, 2009 [Page 151] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 / "402" ; Payment Required / "403" ; Forbidden / "404" ; Not Found / "405" ; Method Not Allowed / "406" ; Not Acceptable / "407" ; Proxy Authentication Required / "408" ; Request Time-out / "410" ; Gone / "411" ; Length Required / "412" ; Precondition Failed / "413" ; Request Entity Too Large / "414" ; Request-URI Too Large / "415" ; Unsupported Media Type / "451" ; Parameter Not Understood / "452" ; reserved / "453" ; Not Enough Bandwidth / "454" ; Session Not Found / "455" ; Method Not Valid in This State / "456" ; Header Field Not Valid for Resource / "457" ; Invalid Range / "458" ; Parameter Is Read-Only / "459" ; Aggregate operation not allowed / "460" ; Only aggregate operation allowed / "461" ; Unsupported Transport / "462" ; Destination Unreachable / "463" ; Destination Prohibited / "464" ; Data Transport Not Ready Yet / "470" ; Connection Authorization Required / "471" ; Connection Credentials not accepted / "472" ; Failure to establish secure connection / "500" ; Internal Server Error / "501" ; Not Implemented / "502" ; Bad Gateway / "503" ; Service Unavailable / "504" ; Gateway Time-out / "505" ; RTSP Version not supported / "551" ; Option not supported / extension-code extension-code = 3DIGIT Reason-Phrase = *TEXT Schulzrinne, et al. Expires May 7, 2009 [Page 152] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 general-header = Cache-Control / Connection / CSeq / Date / Media-Properties / Media-Range / Pipelined-Requests / Proxy-Supported / Seek-Style / Supported / Timestamp / Via / extension-header request-header = Accept / Accept-Credentials / Accept-Encoding / Accept-Language / Authorization / Bandwidth / Blocksize / From / If-Match / If-Modified-Since / If-None-Match / Notify-Reason / Proxy-Require / Range / Referer / Request-Status / Require / Scale / Session / Speed / Supported / Transport / User-Agent / extension-header Schulzrinne, et al. Expires May 7, 2009 [Page 153] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 response-header = Accept-Credentials / Accept-Ranges / Connection-Credentials / ETag / Location / Proxy-Authenticate / Public / Range / Retry-After / RTP-Info / Scale / Session / Server / Speed / Transport / Unsupported / Vary / WWW-Authenticate / extension-header entity-header = Allow / Content-Base / Content-Encoding / Content-Language / Content-Length / Content-Location / Content-Type / Expires / Last-Modified / extension-header 20.2.3. Header Syntax All header syntaxes not defined in this section are defined in section 14 of the HTTP 1.1 specification [RFC2616]. Accept = "Accept" HCOLON [ accept-range *(COMMA accept-range) ] accept-range = media-range *(SEMI accept-param) media-range = ( "*/*" / ( m-type SLASH "*" ) / ( m-type SLASH m-subtype ) ) *( SEMI m-parameter ) accept-param = ("q" EQUAL qvalue) / generic-param qvalue = ( "0" [ "." *3DIGIT ] ) / ( "1" [ "." *3("0") ] ) Accept-Credentials = "Accept-Credentials" HCOLON cred-decision cred-decision = ("User" [LWS cred-info]) Schulzrinne, et al. Expires May 7, 2009 [Page 154] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 / "Proxy" / "Any" / (token [LWS 1*TEXT]) ; For future extensions cred-info = cred-info-data *(COMMA cred-info-data) cred-info-data = DQ RTSP-URI DQ SEMI hash-alg SEMI base64 hash-alg = "sha-256" / extension-alg extension-alg = token Accept-Encoding = "Accept-Encoding" HCOLON [ encoding *(COMMA encoding) ] encoding = codings *(SEMI accept-param) codings = content-coding / "*" content-coding = token Accept-Language = "Accept-Language" HCOLON [ language *(COMMA language) ] language = language-range *(SEMI accept-param) language-range = (1*8ALPHA *( "-" 1*8ALPHA)) / "*" Accept-Ranges = "Accept-Ranges" HCOLON acceptable-ranges acceptable-ranges = (range-unit *(COMMA range-unit)) / "none" range-unit = "NPT" / "SMPTE" / "UTC" / extension-format extension-format = token Allow = "Allow" HCOLON [Method *(COMMA Method)] Authorization = "Authorization" HCOLON credentials credentials = ("Digest" LWS digest-response) / other-response digest-response = dig-resp *(COMMA dig-resp) dig-resp = username / realm / nonce / digest-uri / dresponse / algorithm / cnonce / opaque / message-qop / nonce-count / auth-param username = "username" EQUAL username-value username-value = quoted-string digest-uri = "uri" EQUAL LDQUOT digest-uri-value RDQUOT digest-uri-value = Request-URI ; by HTTP/1.1 message-qop = "qop" EQUAL qop-value cnonce = "cnonce" EQUAL cnonce-value cnonce-value = nonce-value nonce-count = "nc" EQUAL nc-value nc-value = 8LHEX dresponse = "response" EQUAL request-digest request-digest = LDQUOT 32LHEX RDQUOT auth-param = auth-param-name EQUAL ( token / quoted-string ) auth-param-name = token other-response = auth-scheme LWS auth-param *(COMMA auth-param) Schulzrinne, et al. Expires May 7, 2009 [Page 155] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 auth-scheme = token Bandwidth = "Bandwidth" HCOLON 1*DIGIT Blocksize = "Blocksize" HCOLON 1*DIGIT Cache-Control = "Cache-Control" HCOLON cache-directive *(COMMA cache-directive) cache-directive = cache-rqst-directive / cache-rspns-directive cache-rqst-directive = "no-cache" / "max-stale" [EQUAL delta-seconds] / "min-fresh" EQUAL delta-seconds / "only-if-cached" / cache-extension cache-rspns-directive = "public" / "private" / "no-cache" / "no-transform" / "must-revalidate" / "proxy-revalidate" / "max-age" EQUAL delta-seconds / cache-extension cache-extension = token [EQUAL (token / quoted-string)] delta-seconds = 1*DIGIT Connection-Credentials = "Connection-Credentials" HCOLON cred-chain cred-chain = DQ RTSP-URI DQ SEMI base64 Connection = "Connection" HCOLON (connection-token) *(COMMA connection-token) connection-token = token Content-Base = "Content-Base" HCOLON RTSP-URI-Ref Content-Encoding = "Content-Encoding" HCOLON content-coding *(COMMA content-coding) Content-Language = "Content-Language" HCOLON language-tag *(COMMA language-tag) language-tag = primary-tag *( "-" subtag ) primary-tag = 1*8ALPHA subtag = 1*8ALPHA Content-Length = "Content-Length" HCOLON 1*DIGIT Content-Location = "Content-Location" HCOLON RTSP-URI-Ref Content-Type = ( "Content-Type" / "c" ) HCOLON media-type media-type = m-type SLASH m-subtype *(SEMI m-parameter) Schulzrinne, et al. Expires May 7, 2009 [Page 156] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 m-type = discrete-type / composite-type discrete-type = "text" / "image" / "audio" / "video" / "application" / extension-token composite-type = "message" / "multipart" / extension-token extension-token = ietf-token / x-token ietf-token = token x-token = "x-" token m-subtype = extension-token / iana-token iana-token = token m-parameter = m-attribute EQUAL m-value m-attribute = token m-value = token / quoted-string CSeq = "CSeq" HCOLON cseq-nr cseq-nr = 1*9DIGIT Date = "Date" HCOLON RTSP-date RTSP-date = rfc1123-date ; HTTP-date rfc1123-date = wkday "," SP date1 SP time SP "GMT" date1 = 2DIGIT SP month SP 4DIGIT ; day month year (e.g., 02 Jun 1982) time = 2DIGIT ":" 2DIGIT ":" 2DIGIT ; 00:00:00 - 23:59:59 wkday = "Mon" / "Tue" / "Wed" / "Thu" / "Fri" / "Sat" / "Sun" month = "Jan" / "Feb" / "Mar" / "Apr" / "May" / "Jun" / "Jul" / "Aug" / "Sep" / "Oct" / "Nov" / "Dec" ETag = "ETag" HCOLON entity-tag Expires = "Expires" HCOLON RTSP-date From = "From" HCOLON from-spec from-spec = ( name-addr / addr-spec ) *( SEMI from-param ) name-addr = [ display-name ] LAQUOT addr-spec RAQUOT addr-spec = RTSP-URI / absolute-URI absolute-URI = < As defined in RFC 3986> display-name = *(token LWS) / quoted-string from-param = tag-param / generic-param tag-param = "tag" EQUAL token If-Match = "If-Match" HCOLON ("*" / entity-tag-list) entity-tag-list = entity-tag *(COMMA entity-tag) entity-tag = [ weak ] opaque-tag weak = "W/" opaque-tag = quoted-string If-Modified-Since = "If-Modified-Since" HCOLON RTSP-date If-None-Match = "If-None-Match" HCOLON ("*" / entity-tag-list) Last-Modified = "Last-Modified" HCOLON RTSP-date Location = "Location" HCOLON RTSP-URI Media-Properties = "Media-Properties" HCOLON media-prop-list Schulzrinne, et al. Expires May 7, 2009 [Page 157] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 media-prop-list = media-prop-value *(COMMA media-prop-value) media-prop-value = ("Random-Access" [EQUAL POS-FLOAT]) / "Begining-Only" / "No-Seeking" / "Unmutable" / "Dynamic" / "Time-Progressing" / "Unlimited" / ("Time-Limited" EQUAL utc-range-spec) / ("Time-Duration" EQUAL POS-FLOAT) / media-prop-ext media-prop-ext = token [EQUAL (1*rtsp-unreserved / quoted-string)] Media-Range = "Media-Range" HCOLON [ranges-list] Notify-Reason = "Notify-Reason" HCOLON Notify-Reas-val Notify-Reas-val = "end-of-stream" / "media-properties-update" / "scale-change" / Notify-Reason-extension Notify-Reason-extension = token Pipelined-Requests = "Pipelined-Requests" HCOLON startup-id startup-id = 1*8DIGIT Schulzrinne, et al. Expires May 7, 2009 [Page 158] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Proxy-Authenticate = "Proxy-Authenticate" HCOLON challenge-list challenge-list = challenge *(COMMA challenge) challenge = ("Digest" LWS digest-cln *(COMMA digest-cln)) / other-challenge other-challenge = auth-scheme LWS auth-param *(COMMA auth-param) digest-cln = realm / domain / nonce / opaque / stale / algorithm / qop-options / auth-param realm = "realm" EQUAL realm-value realm-value = quoted-string domain = "domain" EQUAL LDQUOT URI *(1*SP URI) RDQUOT URI = RTSP-URI / RTSP-URI-Ref nonce = "nonce" EQUAL nonce-value nonce-value = quoted-string opaque = "opaque" EQUAL quoted-string stale = "stale" EQUAL ( "true" / "false" ) algorithm = "algorithm" EQUAL ("MD5" / "MD5-sess" / token) qop-options = "qop" EQUAL LDQUOT qop-value *("," qop-value) RDQUOT qop-value = "auth" / "auth-int" / token Proxy-Require = "Proxy-Require" HCOLON feature-tag *(COMMA feature-tag) Proxy-Supported = "Proxy-Supported" HCOLON feature-tag *(COMMA feature-tag) Public = "Public" HCOLON Method *(COMMA Method) Range = "Range" HCOLON ranges-list [exec-time] ranges-list = ranges-spec *(COMMA ranges-spec) exec-time = SEMI "time" EQUAL utc-time ranges-spec = npt-range / utc-range / smpte-range / range-ext range-ext = extension-format "=" range-value range-value = 1*(rtsp-unreserved / quoted-string / ":" ) Referer = "Referer" HCOLON RTSP-URI-Ref Request-Status = "Request-Status" HCOLON status-info status-info = cseq-info LWS status-info LWS reason-info cseq-info = "cseq" EQUAL cseq-nr status-info = "status" EQUAL Status-Code reason-info = "reason" EQUAL DQ Reason-Phrase DQ Require = "Require" HCOLON feature-tag-list feature-tag-list = feature-tag *(COMMA feature-tag) Schulzrinne, et al. Expires May 7, 2009 [Page 159] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 RTP-Info = "RTP-Info" HCOLON rtsp-info-spec *(COMMA rtsp-info-spec) rtsp-info-spec = stream-url 1*ssrc-parameter stream-url = "url" EQUAL DQ RTSP-URI-Ref DQ ssrc-parameter = LWS "ssrc" EQUAL ssrc HCOLON ri-parameter *(SEMI ri-parameter) ri-parameter = ("seq" EQUAL 1*DIGIT) / ("rtptime" EQUAL 1*DIGIT) / generic-param Retry-After = "Retry-After" HCOLON delta-seconds [ comment ] *( SEMI retry-param ) retry-param = ("duration" EQUAL delta-seconds) / generic-param Scale = "Scale" HCOLON ["-"] 1*DIGIT [ "." *DIGIT ] Seek-Style = "Seek-Style" HCOLON Seek-S-values Seek-S-values = "RAP" / "First-Prior" / "Next" / Seek-S-value-ext Seek-S-value-ext = token Speed = "Speed" HCOLON 1*DIGIT [ "." *DIGIT ] Server = "Server" HCOLON ( product / comment ) *(LWS (product / comment)) product = token [SLASH product-version] product-version = token comment = LPAREN *( ctext / quoted-pair) RPAREN Session = "Session" HCOLON session-id [ SEMI "timeout" EQUAL delta-seconds ] Supported = "Supported" HCOLON [feature-tag-list] Timestamp = "Timestamp" HCOLON timestamp-value LWS [delay] timestamp-value = *DIGIT [ "." *DIGIT ] delay = *DIGIT [ "." *DIGIT ] Transport = "Transport" HCOLON transport-spec *(COMMA transport-spec) transport-spec = transport-id *tr-parameter transport-id = trans-id-rtp / other-trans trans-id-rtp = "RTP/" profile ["/" lower-transport] ; no LWS is allowed inside transport-id other-trans = token *("/" token) Schulzrinne, et al. Expires May 7, 2009 [Page 160] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 profile = "AVP" / "SAVP" / "AVPF" / token lower-transport = "TCP" / "UDP" / token tr-parameter = (SEMI ( "unicast" / "multicast" )) / (SEMI "interleaved" EQUAL channel [ "-" channel ]) / (SEMI "ttl" EQUAL ttl) / (SEMI "layers" EQUAL 1*DIGIT) / (SEMI "ssrc" EQUAL ssrc *(SLASH ssrc)) / (SEMI "mode" EQUAL mode-spec) / (SEMI "dest_addr" EQUAL addr-list) / (SEMI "src_addr" EQUAL addr-list) / (SEMI trn-param-ext) / (SEMI "setup" EQUAL contrans-setup) / (SEMI "connection" EQUAL contrans-con) contrans-setup = "active" / "passive" / "actpass" contrans-con = "new" / "existing" trn-param-ext = par-name [EQUAL trn-par-value] par-name = token trn-par-value = *(rtsp-unreserved / quoted-string) ttl = 1*3DIGIT ; 0 to 255 ssrc = 8HEX channel = 1*3DIGIT mode-spec = ( DQ mode *(COMMA mode) DQ ) mode = "PLAY" / token addr-list = quoted-addr *(SLASH quoted-addr) quoted-addr = DQ (host-port / extension-addr) DQ host-port = host [":" port] / ":" port extension-addr = 1*qdtext host = < As defined in RFC 3986> port = < As defined in RFC 3986> Schulzrinne, et al. Expires May 7, 2009 [Page 161] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Unsupported = "Unsupported" HCOLON feature-tag-list User-Agent = "User-Agent" HCOLON ( product / comment ) 0*(LWS (product / comment)) Vary = "Vary" HCOLON ( "*" / field-name-list) field-name-list = field-name *(COMMA field-name) field-name = token Via = "Via" HCOLON via-parm *(COMMA via-parm) via-parm = sent-protocol LWS sent-by *( SEMI via-params ) via-params = via-ttl / via-maddr / via-received / via-branch / via-extension via-ttl = "ttl" EQUAL ttl via-maddr = "maddr" EQUAL host via-received = "received" EQUAL (IPv4address / IPv6address) IPv4address = < As defined in RFC 3986> IPv6address = < As defined in RFC 3986> via-branch = "branch" EQUAL token via-extension = generic-param sent-protocol = protocol-name SLASH protocol-version SLASH transport-prot protocol-name = "RTSP" / token protocol-version = token transport-prot = "UDP" / "TCP" / "TLS" / other-transport other-transport = token sent-by = host [ COLON port ] WWW-Authenticate = "WWW-Authenticate" HCOLON challenge-list 20.3. SDP extension Syntax This section defines in ABNF the SDP extensions defined for RTSP. See Appendix D for the definition of the extensions in text. control-attribute = "a=control:" *SP RTSP-URI a-range-def = "a=range:" ranges-spec CRLF a-etag-def = "a=etag:" entity-tag CRLF Schulzrinne, et al. Expires May 7, 2009 [Page 162] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 21. Security Considerations Because of the similarity in syntax and usage between RTSP servers and HTTP servers, the security considerations outlined in [H15] apply. Specifically, please note the following: Abuse of Server Log Information: RTSP and HTTP servers will presumably have similar logging mechanisms, and thus should be equally guarded in protecting the contents of those logs, thus protecting the privacy of the users of the servers. See [H15.1.1] for HTTP server recommendations regarding server logs. Transfer of Sensitive Information: There is no reason to believe that information transferred or controlled via RTSP may be any less sensitive than that normally transmitted via HTTP. Therefore, all of the precautions regarding the protection of data privacy and user privacy apply to implementors of RTSP clients, servers, and proxies. See [H15.1.2] for further details. Attacks Based On File and Path Names: Though RTSP URIs are opaque handles that do not necessarily have file system semantics, it is anticipated that many implementations will translate portions of the Request-URIs directly to file system calls. In such cases, file systems SHOULD follow the precautions outlined in [H15.5], such as checking for ".." in path components. Personal Information: RTSP clients are often privy to the same information that HTTP clients are (user name, location, etc.) and thus should be equally sensitive. See [H15.1] for further recommendations. Privacy Issues Connected to Accept Headers: Since may of the same "Accept" headers exist in RTSP as in HTTP, the same caveats outlined in [H15.1.4] with regards to their use should be followed. DNS Spoofing: Presumably, given the longer connection times typically associated to RTSP sessions relative to HTTP sessions, RTSP client DNS optimizations should be less prevalent. Nonetheless, the recommendations provided in [H15.3] are still relevant to any implementation which attempts to rely on a DNS-to-IP mapping to hold beyond a single use of the mapping. Schulzrinne, et al. Expires May 7, 2009 [Page 163] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Location Headers and Spoofing: If a single server supports multiple organizations that do not trust each another, then it needs to check the values of Location and Content-Location header fields in responses that are generated under control of said organizations to make sure that they do not attempt to invalidate resources over which they have no authority. ([H15.4]) In addition to the recommendations in the current HTTP specification (RFC 2616 [RFC2616], as of this writing) and also of the previous RFC2068 [RFC2068], future HTTP specifications may provide additional guidance on security issues. The following are added considerations for RTSP implementations. Concentrated denial-of-service attack: The protocol offers the opportunity for a remote-controlled denial-of-service attack. See Section 21.1. Session hijacking: Since there is no or little relation between a transport layer connection and an RTSP session, it is possible for a malicious client to issue requests with random session identifiers which would affect unsuspecting clients. The server SHOULD use a large, random and non-sequential session identifier to minimize the possibility of this kind of attack. However, unless the RTSP signalling always are confedentiality protected, e.g. using TLS, an on-path attacker will be able to hijack a session. For real session security, client authentication needs to be performed. Authentication: Servers SHOULD implement both basic and digest [RFC2617] authentication. In environments requiring tighter security for the control messages, the transport layer mechanism TLS [RFC5246] SHOULD be used. Stream issues: RTSP only provides for stream control. Stream delivery issues are not covered in this section, nor in the rest of this draft. RTSP implementations will most likely rely on other protocols such as RTP, IP multicast, RSVP and IGMP, and should address security considerations brought up in those and other applicable specifications. Persistently suspicious behavior: RTSP servers SHOULD return error code 403 (Forbidden) upon receiving a single instance of behavior which is deemed a security risk. RTSP servers SHOULD also be aware of attempts to probe the server for weaknesses and entry points and MAY arbitrarily disconnect and ignore further requests clients which are deemed to be in violation of Schulzrinne, et al. Expires May 7, 2009 [Page 164] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 local security policy. Scope of Multicast: If RTSP is used to control the transmission of media onto a multicast network it is need to consider the scope that delivery has. RTSP supports the TTL Transport header parameter to indicate this scope. However such scope control is risk as it may be set to large and distribute media beyond the intended scope. TLS through proxies: If one uses the possibility to connect TLS in multiple legs (Section 19.3 one really needs to be aware of the trust model. That procedure requires full faith and trust in all proxies that one allows to connect through. They are man in the middle and has access to all that goes on over the TLS connection. Thus it is important to consider if that trust model is acceptable in the actual application. 21.1. Remote denial of Service Attack The attacker may initiate traffic flows to one or more IP addresses by specifying them as the destination in SETUP requests. While the attacker's IP address may be known in this case, this is not always useful in prevention of more attacks or ascertaining the attackers identity. Thus, an RTSP server MUST only allow client-specified destinations for RTSP-initiated traffic flows if the server has ensured that the specified destination address accepts receiving media through different security mechanisms. Security mechanism that are acceptable in an increased generality are; verification of the client's identity, either against a database of known users using RTSP authentication mechanisms (preferably digest authentication or stronger); a list of addresses that accept to be media destinations, especially considering user identity; and media path based verification. The server SHOULD NOT allow the destination field to be set unless a mechanism exists in the system to authorize the request originator to direct streams to the recipient. It is preferred that this authorization be performed by the media recipient (destination) itself and the credentials passed along to the server. However, in certain cases, such as when recipient address is a multicast group, or when the recipient is unable to communicate with the server in an out-of-band manner, this may not be possible. In these cases server may chose another method such as a server-resident authorization list to ensure that the request originator has the proper credentials to request stream delivery to the recipient. One solution that performs the necessary verification of acceptance of media suitable for unicast based delivery is the ICE based NAT Schulzrinne, et al. Expires May 7, 2009 [Page 165] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 traversal method described in [I-D.ietf-mmusic-rtsp-nat]. By using random passwords and username the probability of unintended indication as a valid media destination is very low. If the server include in its STUN requests a cookie (consisting of random material) that is the destination echo back the solution is also safe against having a off-path attacker being able to spoof the STUN checks. Leaving this solution vulnerable only to on-path attackers that can see the STUN requests go to the target of attack. For delivery to multicast addresses there is need for another solution which is not specified here. Schulzrinne, et al. Expires May 7, 2009 [Page 166] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 22. IANA Considerations This section sets up a number of registries for RTSP 2.0 that should be maintained by IANA. For each registry there is a description on what it is required to contain, what specification is needed when adding a entry with IANA, and finally the entries that this document needs to register. See also the Section 2.3 "Extending RTSP". There is also an IANA registration of two SDP attributes. The sections describing how to register an item uses some of the requirements level described in RFC 5226 [RFC5226], namely "First Come, First Served", "Expert Review, "Specification Required", and "Standards Action". A registration request to IANA MUST contain the following information: o A name of the item to register according to the rules specified by the intended registry. o Indication of who has change control over the feature (for example, IETF, ISO, ITU-T, other international standardization bodies, a consortium, a particular company or group of companies, or an individual); o A reference to a further description, if available, for example (in decreasing order of preference) an RFC, a published standard, a published paper, a patent filing, a technical report, documented source code or a computer manual; o For proprietary features, contact information (postal and email address); 22.1. Feature-tags 22.1.1. Description When a client and server try to determine what part and functionality of the RTSP specification and any future extensions that its counter part implements there is need for a namespace. This registry contains named entries representing certain functionality. The usage of feature-tags is explained in Section 11 and Section 13.1. Schulzrinne, et al. Expires May 7, 2009 [Page 167] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 22.1.2. Registering New Feature-tags with IANA The registering of feature-tags is done on a first come, first served basis. The name of the feature MUST follow these rules: The name may be of any length, but SHOULD be no more than twenty characters long. The name MUST NOT contain any spaces, or control characters. The registration SHALL indicate if the feature-tag applies to clients, servers, or proxies only or any combinations of these. Any proprietary feature SHALL have as the first part of the name a vendor tag, which identifies the organization. 22.1.3. Registered entries The following feature-tags are in this specification defined and hereby registered. The change control belongs to the IETF. play.basic: The minimal implementation for playback operations according to this specification. Applies for both clients, servers and proxies. play.scale: Support of scale operations for media playback. Applies only for servers. play.speed: Support of the speed functionality for playback. Applies only for servers. 22.2. RTSP Methods 22.2.1. Description What a method is, is described in section Section 13. Extending the protocol with new methods allow for totally new functionality. 22.2.2. Registering New Methods with IANA A new method MUST be registered through an IETF Standards Action. The reason is that new methods may radically change the protocols behavior and purpose. A specification for a new RTSP method MUST consist of the following items: o A method name which follows the ABNF rules for methods. o A clear specification on what action and response a request with the method will result in. Which directions the method is used, Schulzrinne, et al. Expires May 7, 2009 [Page 168] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S or S->C or both. How the use of headers, if any, modifies the behavior and effect of the method. o A list or table specifying which of the registered headers that are allowed to use with the method in request or/and response. o Describe how the method relates to network proxies. 22.2.3. Registered Entries This specification, RFCXXXX, registers 10 methods: DESCRIBE, GET_PARAMETER, OPTIONS, PAUSE, PLAY, PLAY_NOTIFY REDIRECT, SETUP, SET_PARAMETER, and TEARDOWN. 22.3. RTSP Status Codes 22.3.1. Description A status code is the three digit numbers used to convey information in RTSP response messages, seeSection 8. The number space is limited and care should be taken not to fill the space. 22.3.2. Registering New Status Codes with IANA A new status code can only be registered by an IETF Standards Action. A specification for a new status code MUST specify the following: o The requested number. o A description what the status code means and the expected behavior of the sender and receiver of the code. 22.3.3. Registered Entries RFCXXX, registers the numbered status code defined in the ABNF entry "Status-Code" except "extension-code" in Section 20.2.2. 22.4. RTSP Headers 22.4.1. Description By specifying new headers a method(s) can be enhanced in many different ways. An unknown header will be ignored by the receiving entity. If the new header is vital for a certain functionality, a feature-tag for the functionality can be created and demanded to be used by the counter-part with the inclusion of a Require header carrying the feature-tag. Schulzrinne, et al. Expires May 7, 2009 [Page 169] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 22.4.2. Registering New Headers with IANA Registrations in the registry can be done following the Expert Review policy. A specification SHOULD be provided, preferable an IETF RFC or other Standards Developing Organization specification. The minimal information in a registration request is the header name and the contact information. The specification SHOULD contain the following information: o The name of the header. o An ABNF specification of the header syntax. o A list or table specifying when the header may be used, encompassing all methods, their request or response, the direction (C->S or S->C). o How the header is to be handled by proxies. o A description of the purpose of the header. 22.4.3. Registered entries All headers specified in Section 16 in RFCXXXX are to be registered. Furthermore the following RTSP headers defined in other specifications are registered: o x-wap-profile defined in [3gpp-26234]. o x-wap-profile-diff defined in [3gpp-26234]. o x-wap-profile-warning defined in [3gpp-26234]. o x-predecbufsize defined in [3gpp-26234]. o x-initpredecbufperiod defined in [3gpp-26234]. o x-initpostdecbufperiod defined in [3gpp-26234]. o 3gpp-videopostdecbufsize defined in [3gpp-26234]. o 3GPP-Link-Char defined in [3gpp-26234]. o 3GPP-Adaptation defined in [3gpp-26234]. Schulzrinne, et al. Expires May 7, 2009 [Page 170] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o 3GPP-QoE-Metrics defined in [3gpp-26234]. o 3GPP-QoE-Feedback defined in [3gpp-26234]. The use of "x-" is NOT RECOMMENDED but the above headers in the register list was defined prior to the clarification. 22.5. Accept-Credentials The security framework's TLS connection mechanism has two registerable entities. 22.5.1. Accept-Credentials policies In Section 19.3.1 three policies for how to handle certificates. Further policies may be defined and SHALL be registered with IANA using the following rules: o Registering requires an IETF Standards Action o A registration is required to name a contact person. o Name of the policy. o A describing text that explains how the policy works for handling the certificates. This specification registers the following values: Any Proxy User 22.5.2. Accept-Credentials hash algorithms The Accept-Credentials header (See Section 16.2) allows for the usage of other algorithms for hashing the DER records of accepted entities. The registration of any future algorithm is expected to be extremely rare and could also be an interoperability problem. Therefore the bar for registering new algorithms is placed intentional high. Any registration of a new hash algorithm SHALL fulfill the following requirement: o Follow the IETF Standards Action policy. Schulzrinne, et al. Expires May 7, 2009 [Page 171] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o A definition of the algorithm and its identifier meeting the "token" ABNF requirement. 22.6. Cache-Control Cache Directive Extensions There exist a number of cache directives which can be sent in the Cache-Control header. A registry for this cache directives SHALL be defined with the following rules: o Registering requires an IETF Standards Action. o A registration is required to contain a contact person. o Name of the directive and a definition of the value, if any. o Specification if it is an request or response directive. o A describing text that explains how the cache directive is used for RTSP controlled media streams. This specification registers the following values: no-cache: public: private: no-transform: only-if-cached: max-stale: min-fresh: must-revalidate: proxy-revalidate: max-age: 22.7. Media Properties Schulzrinne, et al. Expires May 7, 2009 [Page 172] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 22.7.1. Description The media streams being controlled by RTSP can have many different properties. The media properties required to cover the use cases that was in mind when writing the specification are defined. However, it can be expected that further inovation will result in new use cases or media streams with properties not covered by the one specified here. Thus new ones can be specified. As new media properties may need substantial amount of new definitions to correctly specify behavior for this property the bar is intended to be high. 22.7.2. Registration Rules Registering new media property SHALL fulfill the following requirements o Follow the Specification Required policy and get the approval of the designated Expert. o Have a ABNF definition of the media property value name that meets "media-prop-ext" definition o A Contact Person for the Registration o Description of all changes to the behavior of RTSP protocol as result of these changes. 22.7.3. Registered Values This specification registers the 9 values listed in Section 16.29. 22.8. Notify-Reason header 22.8.1. Description Notify-Reason values are the way to indicate why a notification was sent. It may also imply that certain headers shall or should be present required for the client to act upon the information the notification carries. New notification behaviors do need to be described to result in interoperable usage, thus specification are required. 22.8.2. Registration Rules Registrations for new Notify-Reason value SHALL fulfill the following requirements Schulzrinne, et al. Expires May 7, 2009 [Page 173] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o Follow the Specification Required policy and get the approval of the designated Expert. o Have a ABNF definition of the Notify reason value name that meets "Notify-Reason-extension" definition o A Contact Person for the Registration o Description of which headers shall be included in the request and response, when it should be sent, and any affect it has on the server client state. 22.8.3. Registered Values This specification registers 3 values defined in the Notify-Reas-val ABNFSection 20.2.3: o end-of-stream o media-properties-update o scale-change 22.9. Range header formats The Range header allows for different range formats. New ones may be registered, but moderation should be applied as it makes interoperability more difficult. A registration SHALL fulfill the following requirements: o Follow the Specification Required policy. o A ABNF definition of the range format that fulfils the "range-ext" definition. o A Contact person for the registration. o Rules for how one handles the range when using a negative Scale. 22.10. RTP-Info header parameters 22.10.1. Desctiption The RTP-Info header (Section 16.43) carries one or more parameter value pairs with information about a particular point in the RTP stream. RTP extensions or new usages may need new types of information. As RTP information that could be needed is likely to be generic enough and to maximize the interoperability registration Schulzrinne, et al. Expires May 7, 2009 [Page 174] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 requires specification required. 22.10.2. Registration Rules Registrations for new Notify-Reason value SHALL fulfill the following requirements o Follow the Specification Required policy and get the approval of the designated Expert. o Have a ABNF definition that meets the "generic-param" definition o A Contact Person for the Registration 22.10.3. Registered Values This specification registers 2 parameter value pairs: o seq o rtptime 22.11. Seek-Style Policies 22.11.1. Description New seek policies may be registered, however a large number of these will complicate implementation substantially. The impact of unknown policies is that the server will not honor the unknown and use the server default policy instead. 22.11.2. Registration Rules Registrations of new Seek-Style polcies SHALL fulfill the following requirements o Follow the Specification Required policy. o Have a ABNF definition of the Seek-Style policy name that meets "Seek-S-value-ext" definition o A Contact Person for the Registration o Description of which headers shall be included in the request and response, when it should be sent, and any affect it has on the server client state. Schulzrinne, et al. Expires May 7, 2009 [Page 175] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 22.11.3. Registered Values This specification registers 3 values: o RAP o First-Prior o Next 22.12. Transport Header Registries The transport header contains a number of parameters which have possibilities for future extensions. Therefore registries for these needs to be defined. 22.12.1. Transport Protocol Specification A registry for the parameter transport-protocol specification SHALL be defined with the following rules: o Registering uses the policy of Specification Required. o A contact person or organization with address and email. o A value definition that are following the ABNF syntax definition. o A describing text that explains how the registered value are used in RTSP. This specification registers the following values: RTP/AVP: Use of the RTP[RFC3550] protocol for media transport in combination with the "RTP profile for audio and video conferences with minimal control"[RFC3551] over UDP. The usage is explained in RFC XXXX, appendix Appendix C.1. RTP/AVP/UDP: the same as RTP/AVP. RTP/AVPF: Use of the RTP[RFC3550] protocol for media transport in combination with the "Extended RTP Profile for RTCP-based Feedback (RTP/AVPF)" [RFC4585] over UDP. The usage is explained in RFC XXXX, appendix Appendix C.1. RTP/AVPF/UDP: the same as RTP/AVPF. Schulzrinne, et al. Expires May 7, 2009 [Page 176] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 RTP/SAVP: Use of the RTP[RFC3550] protocol for media transport in combination with the "The Secure Real-time Transport Protocol (SRTP)" [RFC3711] over UDP. The usage is explained in RFC XXXX, appendix Appendix C.1. RTP/SAVP/UDP: the same as RTP/SAVP. RTP/SAVPF: Use of the RTP[RFC3550] protocol for media transport in combination with the "[RFC5124] over UDP. The usage is explained in RFC XXXX, appendix Appendix C.1. RTP/SAVPF/UDP: the same as RTP/SAVPF. RTP/AVP/TCP: Use of the RTP[RFC3550] protocol for media transport in combination with the "RTP profile for audio and video conferences with minimal control"[RFC3551] over TCP. The usage is explained in RFC XXXX, appendix Appendix C.2.2. RTP/AVPF/TCP: Use of the RTP[RFC3550] protocol for media transport in combination with the "Extended RTP Profile for RTCP-based Feedback (RTP/AVPF)"[RFC4585] over TCP. The usage is explained in RFC XXXX, appendix Appendix C.2.2. RTP/SAVP/TCP: Use of the RTP[RFC3550] protocol for media transport in combination with the "The Secure Real-time Transport Protocol (SRTP)" [RFC3711] over TCP. The usage is explained in RFC XXXX, appendix Appendix C.2.2. RTP/SAVPF/TCP: Use of the RTP[RFC3550] protocol for media transport in combination with the "[RFC5124] over TCP. The usage is explained in RFC XXXX, appendix Appendix C.2.2. 22.12.2. Transport modes A registry for the transport parameter mode SHALL be defined with the following rules: o Registering requires an IETF Standards Action. o A contact person or organization with address and email. o A value definition that are following the ABNF token definition. o A describing text that explains how the registered value are used in RTSP. This specification registers 1 value: Schulzrinne, et al. Expires May 7, 2009 [Page 177] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 PLAY: See RFC XXXX. 22.12.3. Transport Parameters A registry for parameters that may be included in the Transport header SHALL be defined with the following rules: o Registering uses the Specification Required policy. o A value definition that are following the ABNF token definition. o A describing text that explains how the registered value are used in RTSP. This specification registers all the transport parameters defined in Section 16.51. 22.13. URI Schemes This specification defines two URI schemes ("rtsp" and "rtsps") and reserves a third one ("rtspu"). Registrations are following RFC 4395[RFC4395]. 22.13.1. The rtsp URI Scheme URI scheme name: rtsp Status: Permanent URI scheme syntax: See Section 20.2.1 of RFC XXXX. URI scheme semantics: The rtsp scheme is used to indicate resources accessible through the usage of the Real-time Streaming Protocol (RTSP). RTSP allows different operations on the resource identified by the URI, but the primary purpose is the streaming delivery of the resource to a client. However the operations that are currently defined are: Describing the resource for the purpose of configuring the receiving entity (DESCRIBE), configuring the delivery method and its addressing (SETUP), controlling the delivery (PLAY and PAUSE), reading or setting of resource related parameters (SET_PARAMETER and GET_PARAMETER, and termination of the session context created (TEARDOWN). Encoding considerations: IRIs in this scheme are defined and needs to be encoded as RTSP URIs when used within the RTSP protocol. That encoding is done according to RFC 3987. Schulzrinne, et al. Expires May 7, 2009 [Page 178] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Applications/protocols that use this URI scheme name: RTSP 1.0 (RFC 2326), RTSP 2.0 (RFC XXXX) Interoperability considerations: The change in URI syntax performed between RTSP 1.0 and 2.0 can create interoperability issues. Security considerations: All the security threats identified in Section 7 of RFC 3986 applies also to this scheme. They needs to be reviewed and considered in any implementation utilizing this scheme. Contact: Magnus Westerlund, magnus.westerlund@ericsson.com Author/Change controller: IETF References: RFC 2326, RFC 3986, RFC 3987, RFC XXXX 22.13.2. The rtsps URI Scheme URI scheme name: rtsps Status: Permanent URI scheme syntax: See Section 20.2.1 of RFC XXXX. URI scheme semantics: The rtsps scheme is used to indicate resources accessible through the usage of the Real-time Streaming Protocol (RTSP) over TLS. RTSP allows different operations on the resource identified by the URI, but the primary purpose is the streaming delivery of the resource to a client. However the operations that are currently defined are: Describing the resource for the purpose of configuring the receiving entity (DESCRIBE), configuring the delivery method and its addressing (SETUP), controlling the delivery (PLAY and PAUSE), reading or setting of resource related parameters (SET_PARAMETER and GET_PARAMETER, and termination of the session context created (TEARDOWN). Encoding considerations: IRIs in this scheme are defined and needs to be encoded as RTSP URIs when used within the RTSP protocol. That encoding is done according to RFC 3987. Applications/protocols that use this URI scheme name: RTSP 1.0 (RFC 2326), RTSP 2.0 (RFC XXXX) Schulzrinne, et al. Expires May 7, 2009 [Page 179] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Interoperability considerations: The change in URI syntax performed between RTSP 1.0 and 2.0 can create interoperability issues. Security considerations: All the security threats identified in Section 7 of RFC 3986 applies also to this scheme. They needs to be reviewed and considered in any implementation utilizing this scheme. Contact: Magnus Westerlund, magnus.westerlund@ericsson.com Author/Change controller: IETF References: RFC 2326, RFC 3986, RFC 3987, RFC XXXX 22.13.3. The rtspu URI Scheme URI scheme name: rtspu Status: Permanent URI scheme syntax: See Section 3.2 of RFC 2326. URI scheme semantics: The rtspu scheme is used to indicate resources accessible through the usage of the Real-time Streaming Protocol (RTSP) over unrelaible datagram transport. RTSP allows different operations on the resource identified by the URI, but the primary purpose is the streaming delivery of the resource to a client. However the operations that are currently defined are: Describing the resource for the purpose of configuring the receiving entity (DESCRIBE), configuring the delivery method and its addressing (SETUP), controlling the delivery (PLAY and PAUSE), reading or setting of resource related parameters (SET_PARAMETER and GET_PARAMETER, and termination of the session context created (TEARDOWN). Encoding considerations: IRIs in this scheme are defined and needs to be encoded as RTSP URIs when used within the RTSP protocol. That encoding is done according to RFC 3987. Applications/protocols that use this URI scheme name: RTSP 1.0 (RFC 2326) Interoperability considerations: The definition of the transport mechanism of RTSP over UDP has interoperability issues. That makes the usage of this scheme problematic. Schulzrinne, et al. Expires May 7, 2009 [Page 180] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Security considerations: All the security threats identified in Section 7 of RFC 3986 applies also to this scheme. They needs to be reviewed and considered in any implementation utilizing this scheme. Contact: Magnus Westerlund, magnus.westerlund@ericsson.com Author/Change controller: IETF References: RFC 2326, RFC 3986, RFC 3987 22.14. SDP attributes This specification defines three SDP [RFC4566] attributes that it is requested that IANA register. SDP Attribute ("att-field"): Attribute name: range Long form: Media Range Attribute Type of name: att-field Type of attribute: Media and session level Subject to charset: No Purpose: RFC XXXX Reference: RFC XXXX Values: See ABNF definition. Attribute name: control Long form: RTSP control URI Type of name: att-field Type of attribute: Media and session level Subject to charset: No Purpose: RFC XXXX Reference: RFC XXXX Values: Absolute or Relative URIs. Attribute name: etag Long form: Entity Tag Type of name: att-field Type of attribute: Media and session level Subject to charset: No Purpose: RFC XXXX Reference: RFC XXXX Values: See ABNF definition Schulzrinne, et al. Expires May 7, 2009 [Page 181] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 22.15. Media Type Registration for text/parameters Type name: text Subtype name: parameters Required parameters: Optional parameters: Encoding considerations: Security considerations: This format may carry any type of parameters. Some can clear have security requirements, like privacy, confidentiality or integrity requirements. The format has no built in security protection. For the usage it was defined the transport can be protected between server and client using TLS. However, care must be take to consider if also the proxies are trusted with the parameters in case hop-by-hop security is used. If stored as file in file system the necessary precautions needs to be taken in relation to the parameters requirements including object security such as S/MIME [RFC3851]. Interoperability considerations: This media type was mentioned as a fictional example in RFC 2326 but was not formally specified. This have resulted in usage of this media type which may not match its formal definition. Published specification: RFC XXXX, Appendix E. Applications that use this media type: Applications that use RTSP and have additional parameters they like to read and set using the RTSP GET_PARAMETER and SET_PARAMETER methods. Additional information: Magic number(s): File extension(s): Macintosh file type code(s): Person & email address to contact for further information: Magnus Westerlund (magnus.westerlund@ericsson.com) Schulzrinne, et al. Expires May 7, 2009 [Page 182] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Intended usage: Common Restrictions on usage: None Author: Magnus Westerlund (magnus.westerlund@ericsson.com) Change controller: IETF Addition Notes: Schulzrinne, et al. Expires May 7, 2009 [Page 183] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 23. References 23.1. Normative References [3gpp-26234] Third Generation Partnership Project (3GPP), "Transparent end-to-end Packet-switched Streaming Service (PSS); Protocols and codecs; Technical Specification 26.234", December 2002. [FIPS-pub-180-2] National Institute of Standards and Technology (NIST), "Federal Information Processing Standards Publications (FIPS PUBS) 180-2: Secure Hash Standard", Augusti 2002. [RFC0768] Postel, J., "User Datagram Protocol", STD 6, RFC 768, August 1980. [RFC0793] Postel, J., "Transmission Control Protocol", STD 7, RFC 793, September 1981. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2616] Fielding, R., Gettys, J., Mogul, J., Frystyk, H., Masinter, L., Leach, P., and T. Berners-Lee, "Hypertext Transfer Protocol -- HTTP/1.1", RFC 2616, June 1999. [RFC2617] Franks, J., Hallam-Baker, P., Hostetler, J., Lawrence, S., Leach, P., Luotonen, A., and L. Stewart, "HTTP Authentication: Basic and Digest Access Authentication", RFC 2617, June 1999. [RFC2818] Rescorla, E., "HTTP Over TLS", RFC 2818, May 2000. [RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", STD 64, RFC 3550, July 2003. [RFC3551] Schulzrinne, H. and S. Casner, "RTP Profile for Audio and Video Conferences with Minimal Control", STD 65, RFC 3551, July 2003. [RFC3629] Yergeau, F., "UTF-8, a transformation format of ISO 10646", STD 63, RFC 3629, November 2003. [RFC3711] Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K. Norrman, "The Secure Real-time Transport Protocol (SRTP)", Schulzrinne, et al. Expires May 7, 2009 [Page 184] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 RFC 3711, March 2004. [RFC3830] Arkko, J., Carrara, E., Lindholm, F., Naslund, M., and K. Norrman, "MIKEY: Multimedia Internet KEYing", RFC 3830, August 2004. [RFC3851] Ramsdell, B., "Secure/Multipurpose Internet Mail Extensions (S/MIME) Version 3.1 Message Specification", RFC 3851, July 2004. [RFC3986] Berners-Lee, T., Fielding, R., and L. Masinter, "Uniform Resource Identifier (URI): Generic Syntax", STD 66, RFC 3986, January 2005. [RFC3987] Duerst, M. and M. Suignard, "Internationalized Resource Identifiers (IRIs)", RFC 3987, January 2005. [RFC4086] Eastlake, D., Schiller, J., and S. Crocker, "Randomness Requirements for Security", BCP 106, RFC 4086, June 2005. [RFC4291] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, February 2006. [RFC4395] Hansen, T., Hardie, T., and L. Masinter, "Guidelines and Registration Procedures for New URI Schemes", BCP 115, RFC 4395, February 2006. [RFC4566] Handley, M., Jacobson, V., and C. Perkins, "SDP: Session Description Protocol", RFC 4566, July 2006. [RFC4567] Arkko, J., Lindholm, F., Naslund, M., Norrman, K., and E. Carrara, "Key Management Extensions for Session Description Protocol (SDP) and Real Time Streaming Protocol (RTSP)", RFC 4567, July 2006. [RFC4571] Lazzaro, J., "Framing Real-time Transport Protocol (RTP) and RTP Control Protocol (RTCP) Packets over Connection- Oriented Transport", RFC 4571, July 2006. [RFC4585] Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey, "Extended RTP Profile for Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/AVPF)", RFC 4585, July 2006. [RFC4648] Josefsson, S., "The Base16, Base32, and Base64 Data Encodings", RFC 4648, October 2006. [RFC5124] Ott, J. and E. Carrara, "Extended Secure RTP Profile for Schulzrinne, et al. Expires May 7, 2009 [Page 185] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Real-time Transport Control Protocol (RTCP)-Based Feedback (RTP/SAVPF)", RFC 5124, February 2008. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. [RFC5234] Crocker, D. and P. Overell, "Augmented BNF for Syntax Specifications: ABNF", STD 68, RFC 5234, January 2008. [RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security (TLS) Protocol Version 1.2", RFC 5246, August 2008. [RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S., Housley, R., and W. Polk, "Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation List (CRL) Profile", RFC 5280, May 2008. 23.2. Informative References [I-D.ietf-mmusic-rtsp-nat] Goldberg, J., Westerlund, M., and T. Zeng, "An Network Address Translator (NAT) Traversal mechanism for media controlled by Real-Time Streaming Protocol (RTSP)", draft-ietf-mmusic-rtsp-nat-07 (work in progress), July 2008. [ISO.13818-1.2000] International Organization for Standardization, "Information technology - Generic coding of moving pictures and associated audio information: Systems", ISO/ IEC 13818-1:2000, December 2000. [ISO.13818-6.1995] International Organization for Standardization, "Information technology - Generic coding of moving pictures and associated audio information - part 6: Extension for digital storage media and control", ISO Draft Standard 13818-6, November 1995. [ISO.8601.2000] International Organization for Standardization, "Data elements and interchange formats - Information interchange - Representation of dates and times", ISO/IEC Standard 8601, December 2000. [ITU.H323.1996] International Telecommunications Union, "Visual telephone Schulzrinne, et al. Expires May 7, 2009 [Page 186] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 systems and equipment for local area networks which provide a non-guaranteed quality of service", ITU- T Recommendation H.323, May 1996. [NOSSDAV-1997-1] Schulzrinne, H., "A comprehensive multimedia control architecture for the Internet", May 1997. [RFC1123] Braden, R., "Requirements for Internet Hosts - Application and Support", STD 3, RFC 1123, October 1989. [RFC1305] Mills, D., "Network Time Protocol (Version 3) Specification, Implementation", RFC 1305, March 1992. [RFC1644] Braden, B., "T/TCP -- TCP Extensions for Transactions Functional Specification", RFC 1644, July 1994. [RFC1961] McMahon, P., "GSS-API Authentication Method for SOCKS Version 5", RFC 1961, June 1996. [RFC2068] Fielding, R., Gettys, J., Mogul, J., Nielsen, H., and T. Berners-Lee, "Hypertext Transfer Protocol -- HTTP/1.1", RFC 2068, January 1997. [RFC2070] Yergeau, F., Nicol, G., Adams, G., and M. Duerst, "Internationalization of the Hypertext Markup Language", RFC 2070, January 1997. [RFC2326] Schulzrinne, H., Rao, A., and R. Lanphier, "Real Time Streaming Protocol (RTSP)", RFC 2326, April 1998. [RFC2974] Handley, M., Perkins, C., and E. Whelan, "Session Announcement Protocol", RFC 2974, October 2000. [RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A., Peterson, J., Sparks, R., Handley, M., and E. Schooler, "SIP: Session Initiation Protocol", RFC 3261, June 2002. [RFC3388] Camarillo, G., Eriksson, G., Holler, J., and H. Schulzrinne, "Grouping of Media Lines in the Session Description Protocol (SDP)", RFC 3388, December 2002. [RFC4145] Yon, D. and G. Camarillo, "TCP-Based Media Transport in the Session Description Protocol (SDP)", RFC 4145, September 2005. [Stevens98] Schulzrinne, et al. Expires May 7, 2009 [Page 187] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Stevens, W., "Unix Networking Programming - Volume 1, second edition", 1998. [W3C.REC-PICS-labels] Miller, J., Krauskopf, T., Resnick, P., and W. Treese, "PICS label distribution label syntax and communication protocols", W3C REC-PICS-labels-961031. [W3C.REC-PICS-services] Miller, J., Resnick, P., and D. Singer, "Rating services and rating systems (and their machine readable descriptions)", W3C REC-PICS-services-961031, October 1996. Schulzrinne, et al. Expires May 7, 2009 [Page 188] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix A. Examples This section contains several different examples trying to illustrate possible ways of using RTSP. The examples can also help with the understanding of how functions of RTSP work. However remember that this is examples and the normative and syntax description in the other sections takes precedence. Please also note that many of the example contain syntax illegal line breaks to accommodate the formatting restriction that the RFC series impose. A.1. Media on Demand (Unicast) The is an example of media on demand streaming of a media stored in a container file. For purposes of this example, a container file is a storage entity in which multiple continuous media types pertaining to the same end-user presentation are present. In effect, the container file represents an RTSP presentation, with each of its components being RTSP controlled media streams. Container files are a widely used means to store such presentations. While the components are transported as independent streams, it is desirable to maintain a common context for those streams at the server end. This enables the server to keep a single storage handle open easily. It also allows treating all the streams equally in case of any prioritization of streams by the server. It is also possible that the presentation author may wish to prevent selective retrieval of the streams by the client in order to preserve the artistic effect of the combined media presentation. Similarly, in such a tightly bound presentation, it is desirable to be able to control all the streams via a single control message using an aggregate URI. The following is an example of using a single RTSP session to control multiple streams. It also illustrates the use of aggregate URIs. In a container file it is also desirable to not write any URI parts which is not kept, when the container is distributed, like the host and most of the path element. Therefore this example also uses the "*" and relative URI in the delivered SDP. Client C requests a presentation from media server M. The movie is stored in a container file. The client has obtained an RTSP URI to the container file. Schulzrinne, et al. Expires May 7, 2009 [Page 189] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->M: DESCRIBE rtsp://example.com/twister.3gp RTSP/2.0 CSeq: 1 User-Agent: PhonyClient/1.2 M->C: RTSP/2.0 200 OK CSeq: 1 Server: PhonyServer/1.0 Date: Thu, 23 Jan 1997 15:35:06 GMT Content-Type: application/sdp Content-Length: 271 Content-Base: rtsp://example.com/twister.3gp/ Expires: 24 Jan 1997 15:35:06 GMT v=0 o=- 2890844256 2890842807 IN IP4 192.0.2.5 s=RTSP Session i=An Example of RTSP Session Usage e=adm@example.com c=IN IP4 0.0.0.0 a=control: * a=range: npt=0-0:10:34.10 t=0 0 m=audio 0 RTP/AVP 0 a=control: trackID=1 m=video 0 RTP/AVP 26 a=control: trackID=4 Schulzrinne, et al. Expires May 7, 2009 [Page 190] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->M: SETUP rtsp://example.com/twister.3gp/trackID=1 RTSP/2.0 CSeq: 2 User-Agent: PhonyClient/1.2 Require: play.basic Transport: RTP/AVP;unicast;dest_addr=":8000"/":8001" Accept-Ranges: NPT, SMPTE, UTC M->C: RTSP/2.0 200 OK CSeq: 2 Server: PhonyServer/1.0 Transport: RTP/AVP;unicast; ssrc=93CB001E; dest_addr="192.0.2.53:8000"/"192.0.2.53:8001"; src_addr="192.0.2.5:9000"/"192.0.2.5:9001" Session: 12345678 Expires: 24 Jan 1997 15:35:12 GMT Date: 23 Jan 1997 15:35:12 GMT Accept-Ranges: NPT C->M: SETUP rtsp://example.com/twister.3gp/trackID=4 RTSP/2.0 CSeq: 3 User-Agent: PhonyClient/1.2 Require: play.basic Transport: RTP/AVP;unicast;dest_addr=":8002"/":8003" Session: 12345678 Accept-Ranges: NPT, SMPTE, UTC M->C: RTSP/2.0 200 OK CSeq: 3 Server: PhonyServer/1.0 Transport: RTP/AVP;unicast; ssrc=A813FC13; dest_addr="192.0.2.53:8002"/"192.0.2.53:8003"; src_addr="192.0.2.5:9002"/"192.0.2.5:9003"; Session: 12345678 Expires: 24 Jan 1997 15:35:13 GMT Date: 23 Jan 1997 15:35:13 GMT Accept-Range: NPT Schulzrinne, et al. Expires May 7, 2009 [Page 191] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->M: PLAY rtsp://example.com/twister.3gp/ RTSP/2.0 CSeq: 4 User-Agent: PhonyClient/1.2 Range: npt=0-10, npt=30- Session: 12345678 M->C: RTSP/2.0 200 OK CSeq: 4 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:35:14 GMT Session: 12345678 Range: npt=0-10, npt=30-623.10 RTP-Info: url="rtsp://example.com/twister.3gp/trackID=4" ssrc=0D12F123:seq=12345;rtptime=3450012, url="rtsp://example.com/twister.3gp/trackID=1" ssrc=4F312DD8:seq=54321;rtptime=2876889 C->M: PAUSE rtsp://example.com/twister.3gp/ RTSP/2.0 CSeq: 5 User-Agent: PhonyClient/1.2 Session: 12345678 M->C: RTSP/2.0 200 OK CSeq: 5 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:36:01 GMT Session: 12345678 Range: npt=34.57-623.10 C->M: PLAY rtsp://example.com/twister.3gp/ RTSP/2.0 CSeq: 6 User-Agent: PhonyClient/1.2 Range: npt=34.57-623.10 Session: 12345678 M->C: RTSP/2.0 200 OK CSeq: 6 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:36:01 GMT Session: 12345678 Range: npt=34.57-623.10 RTP-Info: url="rtsp://example.com/twister.3gp/trackID=4" ssrc=0D12F123:seq=12555;rtptime=6330012, url="rtsp://example.com/twister.3gp/trackID=1" ssrc=4F312DD8:seq=55021;rtptime=3132889 Schulzrinne, et al. Expires May 7, 2009 [Page 192] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 A.2. Media on Demand using Pipelining This example is basically the example above (Appendix A.1), but now utilizing pipelining to speed up the setup. It requires only two round trip times until the media starts flowing. First of all, the session description is retrieved to determine what media resources need to be setup. In the second step, one sends the necessary SETUP requests and the PLAY request to initiate media delivery. Client C requests a presentation from media server M. The movie is stored in a container file. The client has obtained an RTSP URI to the container file. C->M: DESCRIBE rtsp://example.com/twister.3gp RTSP/2.0 CSeq: 1 User-Agent: PhonyClient/1.2 M->C: RTSP/2.0 200 OK CSeq: 1 Server: PhonyServer/1.0 Date: Thu, 23 Jan 1997 15:35:06 GMT Content-Type: application/sdp Content-Length: 271 Content-Base: rtsp://example.com/twister.3gp/ Expires: 24 Jan 1997 15:35:06 GMT v=0 o=- 2890844256 2890842807 IN IP4 192.0.2.5 s=RTSP Session i=An Example of RTSP Session Usage e=adm@example.com c=IN IP4 0.0.0.0 a=control: * a=range: npt=0-0:10:34.10 t=0 0 m=audio 0 RTP/AVP 0 a=control: trackID=1 m=video 0 RTP/AVP 26 a=control: trackID=4 C->M: SETUP rtsp://example.com/twister.3gp/trackID=1 RTSP/2.0 CSeq: 2 User-Agent: PhonyClient/1.2 Require: play.basic Transport: RTP/AVP;unicast;dest_addr=":8000"/":8001" Accept-Ranges: NPT, SMPTE, UTC Pipelined-Requests: 7654 Schulzrinne, et al. Expires May 7, 2009 [Page 193] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->M: SETUP rtsp://example.com/twister.3gp/trackID=4 RTSP/2.0 CSeq: 3 User-Agent: PhonyClient/1.2 Require: play.basic Transport: RTP/AVP;unicast;dest_addr=":8002"/":8003" Accept-Ranges: NPT, SMPTE, UTC Pipelined-Requests: 7654 C->M: PLAY rtsp://example.com/twister.3gp/ RTSP/2.0 CSeq: 4 User-Agent: PhonyClient/1.2 Range: npt=0-10, npt=30- Session: 12345678 Pipelined-Requests: 7654 M->C: RTSP/2.0 200 OK CSeq: 2 Server: PhonyServer/1.0 Transport: RTP/AVP;unicast; dest_addr="192.0.2.53:8000"/"192.0.2.53:8001"; src_addr="192.0.2.5:9000"/"192.0.2.5:9001"; ssrc=93CB001E Session: 12345678 Expires: 24 Jan 1997 15:35:12 GMT Date: 23 Jan 1997 15:35:12 GMT Accept-Ranges: NPT Pipelined-Requests: 7654 M->C: RTSP/2.0 200 OK CSeq: 3 Server: PhonyServer/1.0 Transport: RTP/AVP;unicast; dest_addr="192.0.2.53:8002"/"192.0.2.53:8003; src_addr="192.0.2.5:9002"/"192.0.2.5:9003"; ssrc=A813FC13 Session: 12345678 Expires: 24 Jan 1997 15:35:13 GMT Date: 23 Jan 1997 15:35:13 GMT Accept-Range: NPT Pipelined-Requests: 7654 M->C: RTSP/2.0 200 OK CSeq: 4 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:35:14 GMT Session: 12345678 Range: npt=0-10, npt=30-623.10 RTP-Info: url="rtsp://example.com/twister.3gp/trackID=4" Schulzrinne, et al. Expires May 7, 2009 [Page 194] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 ssrc=0D12F123:seq=12345;rtptime=3450012, url="rtsp://example.com/twister.3gp/trackID=1" ssrc=4F312DD8:seq=54321;rtptime=2876889 Pipelined-Requests: 7654 A.3. Media on Demand (Unicast) An alternative example of media on demand with a bit more tweaks is the following. Client C requests a movie distributed from two different media servers A (audio.example.com) and V ( video.example.com). The media description is stored on a web server W. The media description contains descriptions of the presentation and all its streams, including the codecs that are available, dynamic RTP payload types, the protocol stack, and content information such as language or copyright restrictions. It may also give an indication about the timeline of the movie. In this example, the client is only interested in the last part of the movie. Schulzrinne, et al. Expires May 7, 2009 [Page 195] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->W: GET /twister.sdp HTTP/1.1 Host: www.example.com Accept: application/sdp W->C: HTTP/1.0 200 OK Date: Thu, 23 Jan 1997 15:35:06 GMT Content-Type: application/sdp Content-Length: 278 Expires: 23 Jan 1998 15:35:06 GMT v=0 o=- 2890844526 2890842807 IN IP4 192.0.2.5 s=RTSP Session e=adm@example.com c=IN IP4 0.0.0.0 a=range:npt=0-1:49:34 t=0 0 m=audio 0 RTP/AVP 0 a=control:rtsp://audio.example.com/twister/audio.en m=video 0 RTP/AVP 31 a=control:rtsp://video.example.com/twister/video C->A: SETUP rtsp://audio.example.com/twister/audio.en RTSP/2.0 CSeq: 1 User-Agent: PhonyClient/1.2 Transport: RTP/AVP/UDP;unicast;dest_addr=":3056"/":3057", RTP/AVP/TCP;unicast;interleaved=0-1 Accept-Ranges: NPT, SMPTE, UTC A->C: RTSP/2.0 200 OK CSeq: 1 Session: 12345678 Transport: RTP/AVP/UDP;unicast; dest_addr="192.0.2.53:3056"/"192.0.2.53:3057"; src_addr="192.0.2.5:5000"/"192.0.2.5:5001" Date: 23 Jan 1997 15:35:12 GMT Server: PhonyServer/1.0 Expires: 24 Jan 1997 15:35:12 GMT Cache-Control: public Accept-Ranges: NPT, SMPTE Schulzrinne, et al. Expires May 7, 2009 [Page 196] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->V: SETUP rtsp://video.example.com/twister/video RTSP/2.0 CSeq: 1 User-Agent: PhonyClient/1.2 Transport: RTP/AVP/UDP;unicast; dest_addr="192.0.2.53:3058"/"192.0.2.53:3059", RTP/AVP/TCP;unicast;interleaved=0-1 Accept-Ranges: NPT, SMPTE, UTC V->C: RTSP/2.0 200 OK CSeq: 1 Session: 23456789 Transport: RTP/AVP/UDP;unicast; dest_addr="192.0.2.53:3058"/"192.0.2.53:3059"; src_addr="192.0.2.5:5002"/"192.0.2.5:5003" Date: 23 Jan 1997 15:35:12 GMT Server: PhonyServer/1.0 Cache-Control: public Expires: 24 Jan 1997 15:35:12 GMT Accept-Ranges: NPT, SMPTE C->V: PLAY rtsp://video.example.com/twister/video RTSP/2.0 CSeq: 2 User-Agent: PhonyClient/1.2 Session: 23456789 Range: smpte=0:10:00- V->C: RTSP/2.0 200 OK CSeq: 2 Session: 23456789 Range: smpte=0:10:00-1:49:23 RTP-Info: url="rtsp://video.example.com/twister/video" ssrc=A17E189D:seq=12312232;rtptime=78712811 Server: PhonyServer/2.0 Date: 23 Jan 1997 15:35:13 GMT Schulzrinne, et al. Expires May 7, 2009 [Page 197] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->A: PLAY rtsp://audio.example.com/twister/audio.en RTSP/2.0 CSeq: 2 User-Agent: PhonyClient/1.2 Session: 12345678 Range: smpte=0:10:00- A->C: RTSP/2.0 200 OK CSeq: 2 Session: 12345678 Range: smpte=0:10:00-1:49:23 RTP-Info: url="rtsp://audio.example.com/twister/audio.en" ssrc=3D124F01:seq=876655;rtptime=1032181 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:35:13 GMT C->A: TEARDOWN rtsp://audio.example.com/twister/audio.en RTSP/2.0 CSeq: 3 User-Agent: PhonyClient/1.2 Session: 12345678 A->C: RTSP/2.0 200 OK CSeq: 3 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:36:52 GMT C->V: TEARDOWN rtsp://video.example.com/twister/video RTSP/2.0 CSeq: 3 User-Agent: PhonyClient/1.2 Session: 23456789 V->C: RTSP/2.0 200 OK CSeq: 3 Server: PhonyServer/2.0 Date: 23 Jan 1997 15:36:52 GMT Even though the audio and video track are on two different servers, may start at slightly different times, and may drift with respect to each other, the client can perform initial synchronize of the two media using RTP-Info and Range received in the PLAY responses. If the two servers are time synchronized the RTCP packets can also be used to maintain synchronization. Schulzrinne, et al. Expires May 7, 2009 [Page 198] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 A.4. Single Stream Container Files Some RTSP servers may treat all files as though they are "container files", yet other servers may not support such a concept. Because of this, clients needs to use the rules set forth in the session description for Request-URIs, rather than assuming that a consistent URI may always be used throughout. Below are an example of how a multi-stream server might expect a single-stream file to be served: C->S: DESCRIBE rtsp://foo.com/test.wav RTSP/2.0 Accept: application/x-rtsp-mh, application/sdp CSeq: 1 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 1 Content-base: rtsp://foo.com/test.wav/ Content-type: application/sdp Content-length: 163 Server: PhonyServer/1.0 Date: Thu, 23 Jan 1997 15:35:06 GMT Expires: 23 Jan 1997 17:00:00 GMT v=0 o=- 872653257 872653257 IN IP4 192.0.2.5 s=mu-law wave file i=audio test c=IN IP4 0.0.0.0 t=0 0 a=control: * m=audio 0 RTP/AVP 0 a=control:streamid=0 Schulzrinne, et al. Expires May 7, 2009 [Page 199] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: SETUP rtsp://foo.com/test.wav/streamid=0 RTSP/2.0 Transport: RTP/AVP/UDP;unicast; dest_addr=":6970"/":6971";mode="PLAY" CSeq: 2 User-Agent: PhonyClient/1.2 Accept-Ranges: NPT, SMPTE, UTC S->C: RTSP/2.0 200 OK Transport: RTP/AVP/UDP;unicast; dest_addr="192.0.2.53:6970"/"192.0.2.53:6971"; src_addr="192.0.2.5:6970"/"192.0.2.5:6971"; mode="PLAY";ssrc=EAB98712 CSeq: 2 Session: 2034820394 Expires: 23 Jan 1997 16:00:00 GMT Server: PhonyServer/1.0 Date: 23 Jan 1997 15:35:07 GMT Accept-Ranges: NPT C->S: PLAY rtsp://foo.com/test.wav/ RTSP/2.0 CSeq: 3 User-Agent: PhonyClient/1.2 Session: 2034820394 S->C: RTSP/2.0 200 OK CSeq: 3 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:35:08 GMT Session: 2034820394 Range: npt=0-600 RTP-Info: url="rtsp://foo.com/test.wav/streamid=0" ssrc=0D12F123:seq=981888;rtptime=3781123 Note the different URI in the SETUP command, and then the switch back to the aggregate URI in the PLAY command. This makes complete sense when there are multiple streams with aggregate control, but is less than intuitive in the special case where the number of streams is one. However the server has declared that the aggregated control URI in the SDP and therefore this is legal. In this case, it is also required that servers accept implementations that use the non-aggregated interpretation and use the individual media URI, like this: C->S: PLAY rtsp://example.com/test.wav/streamid=0 RTSP/2.0 CSeq: 3 User-Agent: PhonyClient/1.2 Schulzrinne, et al. Expires May 7, 2009 [Page 200] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 A.5. Live Media Presentation Using Multicast The media server M chooses the multicast address and port. Here, it is assumed that the web server only contains a pointer to the full description, while the media server M maintains the full description. C->W: GET /sessions.html HTTP/1.1 Host: www.example.com W->C: HTTP/1.1 200 OK Content-Type: text/html ... ... C->M: DESCRIBE rtsp://live.example.com/concert/audio RTSP/2.0 CSeq: 1 Supported: play.basic, play.scale User-Agent: PhonyClient/1.2 M->C: RTSP/2.0 200 OK CSeq: 1 Content-Type: application/sdp Content-Length: 183 Server: PhonyServer/1.0 Date: Thu, 23 Jan 1997 15:35:06 GMT Supported: play.basic v=0 o=- 2890844526 2890842807 IN IP4 192.0.2.5 s=RTSP Session t=0 0 m=audio 3456 RTP/AVP 0 c=IN IP4 224.2.0.1/16 a=control: rtsp://live.example.com/concert/audio a=range:npt=0- Schulzrinne, et al. Expires May 7, 2009 [Page 201] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->M: SETUP rtsp://live.example.com/concert/audio RTSP/2.0 CSeq: 2 Transport: RTP/AVP;multicast Accept-Ranges: NPT, SMPTE, UTC User-Agent: PhonyClient/1.2 M->C: RTSP/2.0 200 OK CSeq: 2 Server: PhonyServer/1.0 Date: Thu, 23 Jan 1997 15:35:06 GMT Transport: RTP/AVP;multicast; dest_addr="224.2.0.1:3456"/"224.2.0.1:3457";ttl=16 Session: 0456804596 Accept-Ranges: NPT, UTC C->M: PLAY rtsp://live.example.com/concert/audio RTSP/2.0 CSeq: 3 Session: 0456804596 User-Agent: PhonyClient/1.2 M->C: RTSP/2.0 200 OK CSeq: 3 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:35:07 GMT Session: 0456804596 Range:npt=1256- RTP-Info: url="rtsp://live.example.com/concert/audio" ssrc=0D12F123:seq=1473; rtptime=80000 A.6. Capability Negotiation This examples illustrate how the client and server determines their capability to support a special feature, in this case "play.scale". The server, through the clients request and the included Supported header, learns the client supports RTSP 2.0, and also supports the playback time scaling feature of RTSP. The server's response contains the following feature related information to the client; it supports the basic playback (play.basic), the extended functionality of time scaling of content (play.scale), and one "example.com" proprietary feature (com.example.flight). The client also learns the methods supported (Public header) by the server for the indicated resource. Schulzrinne, et al. Expires May 7, 2009 [Page 202] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: OPTIONS rtsp://media.example.com/movie/twister.3gp RTSP/2.0 CSeq: 1 Supported: play.basic, play.scale User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 1 Public: OPTIONS, SETUP, PLAY, PAUSE, TEARDOWN Server: PhonyServer/2.0 Supported: play.basic, play.scale, com.example.flight When the client sends its SETUP request it tells the server that it is requires support of the play.scale feature for this session by including the Require header. C->S: SETUP rtsp://media.example.com/twister.3gp/trackID=1 RTSP/2.0 CSeq: 3 User-Agent: PhonyClient/1.2 Transport: RTP/AVP/UDP;unicast; dest_addr="192.0.2.53:3056"/"192.0.2.53:3057", RTP/AVP/TCP;unicast;interleaved=0-1 Require: play.scale Accept-Ranges: NPT, SMPTE, UTC User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 3 Session: 12345678 Transport: RTP/AVP/UDP;unicast; dest_addr="192.0.2.53:3056"/"192.0.2.53:3057"; src_addr="192.0.2.5:5000"/"192.0.2.5:5001" Server: PhonyServer/2.0 Accept-Ranges: NPT, SMPTE Schulzrinne, et al. Expires May 7, 2009 [Page 203] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix B. RTSP Protocol State Machine The RTSP session state machine describes the behavior of the protocol from RTSP session initialization through RTSP session termination. The State machine is defined on a per session basis which is uniquely identified by the RTSP session identifier. The session may contain one or more media streams depending on state. If a single media stream is part of the session it is in non-aggregated control. If two or more is part of the session it is in aggregated control. The below state machine is a normative description of the protocols behavior. However, in case of ambiguity with the earlier parts of this specification, the description in the earlier parts SHALL take precedence. B.1. States The state machine contains three states, described below. For each state there exist a table which shows which requests and events that is allowed and if they will result in a state change. Init: Initial state no session exist. Ready: Session is ready to start playing. Play: Session is playing, i.e. sending media stream data in the direction S->C. B.2. State variables This representation of the state machine needs more than its state to work. A small number of variables are also needed and is explained below. NRM: The number of media streams part of this session. RP: Resume point, the point in the presentation time line at which a request to continue will resume from. A time format for the variable is not mandated. B.3. Abbreviations To make the state tables more compact a number of abbreviations are used, which are explained below. Schulzrinne, et al. Expires May 7, 2009 [Page 204] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 IFI: IF Implemented. md: Media PP: Pause Point, the point in the presentation time line at which the presentation was paused. Prs: Presentation, the complete multimedia presentation. RedP: Redirect Point, the point in the presentation time line at which a REDIRECT was specified to occur. SES: Session. B.4. State Tables This section contains a table for each state. The table contains all the requests and events that this state is allowed to act on. The events which is method names are, unless noted, requests with the given method in the direction client to server (C->S). In some cases there exist one or more requisite. The response column tells what type of response actions should be performed. Possible actions that is requested for an event includes: response codes, e.g. 200, headers that MUST be included in the response, setting of state variables, or setting of other session related parameters. The new state column tells which state the state machine changes to. The response to valid request meeting the requisites is normally a 2xx (SUCCESS) unless other noted in the response column. The exceptions needs to be given a response according to the response column. If the request does not meet the requisite, is erroneous or some other type of error occur the appropriate response code MUST be sent. If the response code is a 4xx the session state is unchanged. A response code of 3rr will result in that the session is ended and its state is changed to Init. A response code of 304 results in no state change. However there exist restrictions to when a 3rr response may be used. A 5xx response SHALL NOT result in any change of the session state, except if the error is not possible to recover from. A unrecoverable error SHALL result the ending of the session. As it in the general case can't be determined if it was a unrecoverable error or not the client will be required to test. In the case that the next request after a 5xx is responded with 454 (Session Not Found) the client knows that the session has ended. The server will timeout the session after the period of time specified in the SETUP response, if no activity from the client is detected. Therefore there exist a timeout event for all states except Init. Schulzrinne, et al. Expires May 7, 2009 [Page 205] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 In the case that NRM = 1 the presentation URI is equal to the media URI or a specified presentation URI. For NRM > 1 the presentation URI MUST be other than any of the medias that are part of the session. This applies to all states. +---------------+-----------------+---------------------------------+ | Event | Prerequisite | Response | +---------------+-----------------+---------------------------------+ | DESCRIBE | Needs REDIRECT | 3rr, Redirect | | | | | | DESCRIBE | | 200, Session description | | | | | | OPTIONS | Session ID | 200, Reset session timeout | | | | timer | | | | | | OPTIONS | | 200 | | | | | | SET_PARAMETER | Valid parameter | 200, change value of parameter | | | | | | GET_PARAMETER | Valid parameter | 200, return value of parameter | +---------------+-----------------+---------------------------------+ Table 13: None state-machine changing events The methods in Table 13 do not have any effect on the state machine or the state variables. However some methods do change other session related parameters, for example SET_PARAMETER which will set the parameter(s) specified in its body. Also all of these methods that allows Session header will also update the keep-alive timer for the session. +------------------+----------------+-----------+-------------------+ | Action | Requisite | New State | Response | +------------------+----------------+-----------+-------------------+ | SETUP | | Ready | NRM=1, RP=0.0 | | | | | | | SETUP | Needs Redirect | Init | 3rr Redirect | | | | | | | S -> C: REDIRECT | No Session hdr | Init | Terminate all SES | +------------------+----------------+-----------+-------------------+ Table 14: State: Init The initial state of the state machine, see Table 14 can only be left by processing a correct SETUP request. As seen in the table the two state variables are also set by a correct request. This table also shows that a correct SETUP can in some cases be redirected to another URI and/or server by a 3rr response. Schulzrinne, et al. Expires May 7, 2009 [Page 206] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 +--------------+-----------------+-----------+----------------------+ | Action | Requisite | New State | Response | +--------------+-----------------+-----------+----------------------+ | SETUP | New URI | Ready | NRM +=1 | | | | | | | SETUP | URI Setup prior | Ready | Change transport | | | | | param | | | | | | | TEARDOWN | Prs URI, | Init | No session hdr, NRM | | | | | = 0 | | | | | | | TEARDOWN | md URI,NRM=1 | Init | No Session hdr, NRM | | | | | = 0 | | | | | | | TEARDOWN | md URI,NRM>1 | Ready | Session hdr, NRM -= | | | | | 1 | | | | | | | PLAY | Prs URI, No | Play | Play from RP | | | range | | | | | | | | | PLAY | Prs URI, Range | Play | According to range | | | | | | | PAUSE | Prs URI | Ready | Return PP | | | | | | | SC:REDIRECT | Range hdr | Ready | Set RedP | | | | | | | SC:REDIRECT | no range hdr | Init | Session is removed | | | | | | | Timeout | | Init | | | | | | | | RedP reached | | Init | TEARDOWN of session | +--------------+-----------------+-----------+----------------------+ Table 15: State: Ready In the Ready state, see Table 15, some of the actions are depending on the number of media streams (NRM) in the session, i.e. aggregated or non-aggregated control. A setup request in the ready state can either add one more media stream to the session or if the media stream (same URI) already is part of the session change the transport parameters. TEARDOWN is depending on both the Request-URI and the number of media stream within the session. If the Request-URI is the presentations URI the whole session is torn down. If a media URI is used in the TEARDOWN request and more than one media exist in the session, the session will remain and a session header MUST be returned in the response. If only a single media stream remains in the session when performing a TEARDOWN with a media URI the session is removed. The number of media streams remaining after tearing down Schulzrinne, et al. Expires May 7, 2009 [Page 207] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 a media stream determines the new state. +--------------+-----------------+-----------+----------------------+ | Action | Requisite | New State | Response | +--------------+-----------------+-----------+----------------------+ | PAUSE | PrsURI | Ready | Set RP to present | | | | | point | | | | | | | PP reached | | Ready | RP = PP | | | | | | | End of media | All media | Play | Set RP = End of | | | | | media | | | | | | | End of range | | Play | Set RP = End of | | | | | range | | | | | | | PLAY | Prs URI, No | Play | Play from present | | | range | | point | | | | | | | PLAY | Prs URI, Range | Play | According to range | | | | | | | PLAY_NOTIFY | | Play | 200 | | | | | | | SETUP | New URI | Play | 455 | | | | | | | SETUP | Setuped URI | Play | 455 | | | | | | | SETUP | Setuped URI, | Play | Change transport | | | IFI | | param. | | | | | | | TEARDOWN | Prs URI | Init | No session hdr | | | | | | | TEARDOWN | md URI,NRM=1 | Init | No Session hdr, | | | | | NRM=0 | | | | | | | TEARDOWN | md URI | Play | 455 | | | | | | | SC:REDIRECT | Range hdr | Play | Set RedP | | | | | | | SC:REDIRECT | no range hdr | Init | Session is removed | | | | | | | RedP reached | | Init | TEARDOWN of session | | | | | | | Timeout | | Init | Stop Media playout | +--------------+-----------------+-----------+----------------------+ Table 16: State: Play Schulzrinne, et al. Expires May 7, 2009 [Page 208] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The Play state table, see Table 16, is the largest. The table contains an number of requests that has presentation URI as a prerequisite on the Request-URI, this is due to the exclusion of non- aggregated stream control in sessions with more than one media stream. To avoid inconsistencies between the client and server, automatic state transitions are avoided. This can be seen at for example "End of media" event when all media has finished playing, the session still remain in Play state. An explicit PAUSE request MUST be sent to change the state to Ready. It may appear that there exist an automatic transitions in "RedP reached" and "PP reached", however they are requested and acknowledge before they take place. The time at which the transition will happen is known by looking at the range header. If the client sends request close in time to these transitions it needs to be prepared for getting error message as the state may or may not have changed. Schulzrinne, et al. Expires May 7, 2009 [Page 209] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix C. Media Transport Alternatives This section defines how certain combinations of protocols, profiles and lower transports are used. This includes the usage of the Transport header's source and destination address parameters "src_addr" and "dest_addr". C.1. RTP This section defines the interaction of RTSP with respect to the RTP protocol [RFC3550]. It also defines any necessary media transport signalling with regards to RTP. The available RTP profiles and lower layer transports are described below along with rules on signalling the available combinations. C.1.1. AVP The usage of the "RTP Profile for Audio and Video Conferences with Minimal Control" [RFC3551] when using RTP for media transport over different lower layer transport protocols is defined below in regards to RTSP. One such case is defined within this document, the use of embedded (interleaved) binary data as defined in Section 14. The usage of this method is indicated by include the "interleaved" parameter. When using embedded binary data the "src_addr" and "dest_addr" SHALL NOT be used. This addressing and multiplexing is used as defined with use of channel numbers and the interleaved parameter. C.1.2. AVP/UDP This part describes sending of RTP [RFC3550] over lower transport layer UDP [RFC0768] according to the profile "RTP Profile for Audio and Video Conferences with Minimal Control" defined in RFC 3551 [RFC3551]. This profiles requires one or two uni- or bi-directional UDP flows per media stream. The first UDP flow is for RTP and the second is for RTCP. Embedding of RTP data with the RTSP messages, in accordance with Section 14, SHOULD NOT be performed when RTSP messages are transported over unreliable transport protocols, like UDP [RFC0768]. The RTP/UDP and RTCP/UDP flows can be established using the Transport header's "src_addr", and "dest_addr" parameters. In RTSP PLAY mode, the transmission of RTP packets from client to server is unspecified. The behavior in regards to such RTP packets Schulzrinne, et al. Expires May 7, 2009 [Page 210] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 MAY be defined in future. The "src_addr" and "dest_addr" parameters are used in the following way for media playback, i.e. Mode=PLAY: o The "src_addr" and "dest_addr" parameters MUST contain either 1 or 2 address specifications. o Each address specification for RTP/AVP/UDP or RTP/AVP/TCP MUST contain either: * both an address and a port number, or * a port number without an address. o The first address and port pair given in either of the parameters applies to the RTP stream. The second address and port pair if present applies to the RTCP stream. o The RTP/UDP packets from the server to the client SHALL be sent to the address and port given by first address and port pair of the "dest_addr" parameter. o The RTCP/UDP packets from the server to the client SHALL be sent to the address and port given by the second address and port pair of the "dest_addr" parameter. If no second pair is specified RTCP SHALL NOT be sent. o The RTCP/UDP packets from the client to the server SHALL be sent to the address and port given by the second address and port pair of the "src_addr" parameter. If no second pair is given RTCP SHALL NOT be sent. o The RTP/UDP packets from the client to the server SHALL be sent to the address and port given by the first address and port pair of the "src_addr" parameter. o RTP and RTCP Packets SHOULD be sent from the corresponding receiver port, i.e. RTCP packets from server should be sent from the "src_addr" parameters second address port pair. C.1.3. AVPF/UDP The RTP profile "Extended RTP Profile for RTCP-based Feedback (RTP/ AVPF)"[RFC4585] MAY be used as RTP profiles in session using RTP. All that is defined for AVP SHALL also apply for AVPF. The usage of AVPF is indicated by the media initialization protocol Schulzrinne, et al. Expires May 7, 2009 [Page 211] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 used. In the case of SDP it is indicated by media lines (m=) containing the profile RTP/AVPF. That SDP MAY also contain further AVPF related SDP attributes configuring the AVPF session regarding reporting interval and feedback messages that shall be used that SHALL be followed. C.1.4. SAVP/UDP The RTP profile "The Secure Real-time Transport Protocol (SRTP)" [RFC3711] is an RTP profile (SAVP) that MAY be used in RTSP sessions using RTP. All that is defined for AVP SHALL also apply for SAVP. The usage of SRTP requires that a security association is established. The RECOMMENDED mechanism for establishing that security association is to use MIKEY with RTSP as defined in RFC 4567 [RFC4567]. C.1.5. SAVPF/UDP The RTP profile "Extended Secure RTP Profile for RTCP-based Feedback (RTP/SAVPF)" [RFC5124] is an RTP profile (SAVPF) that MAY be used in RTSP sessions using RTP. All that is defined for AVP SHALL also apply for SAVPF. The usage of SRTP requires that a security association is established. The RECOMMENDED mechanism for establishing that security association is to use MIKEY[RFC3830] with RTSP as defined in RFC 4567 [RFC4567]. C.1.6. RTCP usage with RTSP RTCP has several usages when RTP is used for media transport as explained below. Due to that RTCP SHALL be supported if an RTSP agent handles RTP. C.1.6.1. Media synchronization RTCP provides media synchronization and clock drift compensation. The first is available from RTP-Info header to accomplish the initial synchronization. But to be able to handle any clockdrift between the media streams, RTCP is needed. C.1.6.2. RTSP Session keep-alive RTCP traffic from the RTSP client to the RTSP server SHALL function as keep-alive. Which requires an RTSP server supporting RTP to use the received RTCP packets as indications that the client desires the related RTSP session to be kept alive. Schulzrinne, et al. Expires May 7, 2009 [Page 212] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C.1.6.3. Bit-rate adapation RTCP Receiver reports and any additional feedback from the client SHALL be used adapt the bit-rate used over the transport for all cases when RTP is sent over UDP. A RTP sender without reserved resources SHALL NOT use more than its fair share of the available resources. This can be determined by comparing on short to medium term (some seconds) the used bit-rate and adapt it so that the RTP sender sends at a bit-rate comparable to what a TCP sender would achieve on average over the same path. C.2. RTP over TCP Transport of RTP over TCP can be done in two ways, over independent TCP connections using RFC 4571 [RFC4571] or interleaved in the RTSP control connection. In both cases the protocol SHALL be "rtp" and the lower layer SHALL be TCP. The profile may be any of the above specified ones; AVP, AVPF, SAVP or SAVPF. C.2.1. Interleaved RTP over TCP The use of embedded (interleaved) binary data transported on the RTSP connection is possible as specified in Section 14. When using this declared combination of interleaved binary data the RTSP messages MUST be transported over TCP. TLS may or may not be used. One should however consider that this will result that all media streams go through any proxy. Using independent TCP connections can avoid that issue. C.2.2. RTP over independent TCP In this Appendix, we describe the sending of RTP [RFC3550] over lower transport layer TCP [RFC0793] according to "Framing Real-time Transport Protocol (RTP) and RTP Control Protocol (RTCP) Packets over Connection-Oriented Transport" [RFC4571]. This Appendix adapts the guidelines for using RTP over TCP within SIP/SDP [RFC4145] to work with RTSP. A client codes the support of RTP over independent TCP by specifying an RTP/AVP/TCP transport option without an interleaved parameter in the Transport line of a SETUP request. This transport option MUST include the "unicast" parameter. If the client wishes to use RTP with RTCP, two ports (or two address/ port pairs) are specified by the dest_addr parameter. If the client wishes to use RTP without RTCP, one port (or one address/port pair) is specified by the dest_addr parameter. Ordering rules of dest_addr Schulzrinne, et al. Expires May 7, 2009 [Page 213] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 ports follow the rules for RTP/AVP/UDP. If the client wishes to play the active role in initiating the TCP connection, it MAY set the "setup" parameter (See Section 16.51) on the Transport line to be "active", or it MAY omit the setup parameter, as active is the default. If the client signals the active role, the ports for all dest_addr values MUST be set to 9 (the discard port). If the client wishes to play the passive role in TCP connection initiation, it MUST set the "setup" parameter on the Transport line to be "passive". If the client is able to assume the active or the passive role, it MUST set the "setup" parameter on the Transport line to be "actpass". In either case, the dest_addr port value for RTP MUST be set to the TCP port number on which the client is expecting to receive the RTP stream connection, and the dest_addr port value for RTCP MUST be set to the TCP port number on which the client is expecting to receive the RTCP stream connection. If upon receipt of a non-interleaved RTP/AVP/TCP SETUP request, a server decides to accept this requested option, the 2xx reply MUST contain a Transport option that specifies RTP/AVP/TCP (without using the interleaved parameter, and with using the unicast parameter). The dest_addr parameter value MUST be echoed from the parameter value in the client request unless the destination address (only port) was not provided in which can the server MAY include the source address of the RTSP TCP connection with the port number unchanged. In addition, the server reply MUST set the setup parameter on the Transport line, to indicate the role the server will play in the connection setup. Permissible values are "active" (if a client set "setup" to "passive" or "actpass") and "passive" (if a client set "setup" to "active" or "actpass"). If a server sets "setup" to "passive", the "src_addr" in the reply MUST indicate the ports the server is willing to receive an RTP connection and (if the client requested an RTCP connection by specifying two dest_addr ports or address/port pairs) and RTCP connection. If a server sets "setup" to "active", the ports specified in "src_addr" MUST be set to 9. The server MAY use the "ssrc" parameter, following the guidance in Section 16.51. Port ordering for src_addr follows the rules for RTP/AVP/UDP. For cases when servers have a public IP-address it is RECOMMENDED that the server take the passive role and the client the active role. This help in cases when the client is behind a NAT. After sending (receiving) a 2xx reply for a SETUP method for a non- Schulzrinne, et al. Expires May 7, 2009 [Page 214] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 interleaved RTP/AVP/TCP media stream, the active party SHOULD initiate the TCP connection as soon as possible. The client SHALL NOT send a PLAY request prior to the establishment of all the TCP connections negotiated using SETUP for the session. In case the server receives a PLAY request in a session that has not yet established all the TCP connections, it SHALL respond using the 464 "Data Transport Not Ready Yet" (Section 15.4.16) error code. Once the PLAY request for a media resource transported over non- interleaved RTP/AVP/TCP occurs, media begins to flow from server to client over the RTP TCP connection, and RTCP packets flow bidirectionally over the RTCP TCP connection. As in the RTP/UDP case, client to server traffic on the TCP port is unspecified by this memo. The packets that travel on these connections SHALL be framed using the protocol defined in [RFC4571], not by the framing defined for interleaving RTP over the RTSP control connection defined in Section 14. A successful PAUSE request for a media being transported over RTP/ AVP/TCP pauses the flow of packets over the connections, without closing the connections. A successful TEARDOWN request signals that the TCP connections for RTP and RTCP are to be closed as soon as possible. Subsequent SETUP requests on an already-SETUP RTP/AVP/TCP URI may be ambiguous in the following way: does the client wish to open up new TCP RTP and RTCP connections for the URI, or does the client wish to continue using the existing TCP RTP and RTCP connections? The client SHOULD use the "connection" parameter (defined in Section 16.51) on the Transport line to make its intention clear in the regard (by setting "connection" to "new" if new connections are needed, and by setting "connection" to "existing" if the existing connections are to be used). After a 2xx reply for a SETUP request for a new connection, parties should close the pre-existing connections, after waiting a suitable period for any stray RTP or RTCP packets to arrive. Below, we rewrite part of the example media on demand example shown in Appendix A.1 to use RTP/AVP/TCP non-interleaved: Schulzrinne, et al. Expires May 7, 2009 [Page 215] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->M: DESCRIBE rtsp://example.com/twister.3gp RTSP/2.0 CSeq: 1 User-Agent: PhonyClient/1.2 M->C: RTSP/2.0 200 OK CSeq: 1 Server: PhonyServer/1.0 Date: Thu, 23 Jan 1997 15:35:06 GMT Content-Type: application/sdp Content-Length: 227 Content-Base: rtsp://example.com/twister.3gp/ Expires: 24 Jan 1997 15:35:06 GMT v=0 o=- 2890844256 2890842807 IN IP4 192.0.2.5 s=RTSP Session i=An Example of RTSP Session Usage e=adm@example.com c=IN IP4 0.0.0.0 a=control: * a=range: npt=0-0:10:34.10 t=0 0 m=audio 0 RTP/AVP 0 a=control: trackID=1 C->M: SETUP rtsp://example.com/twister.3gp/trackID=1 RTSP/2.0 CSeq: 2 User-Agent: PhonyClient/1.2 Require: play.basic Transport: RTP/AVP/TCP;unicast;dest_addr=":9"/":9" setup=active;connection=new Schulzrinne, et al. Expires May 7, 2009 [Page 216] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Accept-Ranges: NPT, SMPTE, UTC M->C: RTSP/2.0 200 OK CSeq: 2 Server: PhonyServer/1.0 Transport: RTP/AVP/TCP;unicast; dest_addr=":9"/":9"; src_addr="192.0.2.5:9000"/"192.0.2.5:9001" setup=passive;connection=new;ssrc=93CB001E Session: 12345678 Expires: 24 Jan 1997 15:35:12 GMT Date: 23 Jan 1997 15:35:12 GMT Accept-Ranges: NPT C->M: TCP Connection Establishment C->M: PLAY rtsp://example.com/twister.3gp/ RTSP/2.0 CSeq: 4 User-Agent: PhonyClient/1.2 Range: npt=0-10, npt=30- Session: 12345678 M->C: RTSP/2.0 200 OK CSeq: 4 Server: PhonyServer/1.0 Date: 23 Jan 1997 15:35:14 GMT Session: 12345678 Range: npt=0-10, npt=30-623.10 RTP-Info: url="rtsp://example.com/twister.3gp/trackID=1" ssrc=4F312DD8:seq=54321;rtptime=2876889 C.2.3. Handling Media Clock Time Jumps in the RTP Media Layer RTSP allows media clients to control selected, non-contiguous sections of media presentations, rendering those streams with an RTP media layer[RFC3550]. Such control allows jumps to be created in media clock (e.g. NPT) timeline of the RTSP session. The simple case of jumps in media clock time is caused by multiple ranges in the range specifier of a PLAY request. This allows the media layer rendering the RTP stream without being affected by jumps in media clock time. The RTP timestamps for the next media segment is set so that they become continuous with the previous media segment in the request. The RTP sequence number for the first packet in the new segment will be the next following the last packet in the previous segment, i.e. monotonically increasing. The goal is to allow the media rendering layer to work without interruption or reconfiguration across the jumps in media clock. This should be possible in all cases of multiple ranges in a PLAY request for media that has random- Schulzrinne, et al. Expires May 7, 2009 [Page 217] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 access properties. It is also possible when one PLAY request replaces another ongoing for media with random-access properties. In both cases care to align frames or similar media dependent structures are need but likely possible. In cases where jumps in media clock time are a result of RTSP signalling operations arriving during or after an PLAY operation, the processing delay or request timing can result in that media becomes non-continuous. The server becomes unable to send the media so that it arrive timely and still carry timestamps to make the media stream continuous. In these cases the server will produce RTP streams where there are gaps in the RTP timeline for the media. In such cases, if the media has frame structure, aligning the timestamp for the next frame with the previous structure reduces the burden to render this media. The gap should represent the time the server hasn't been serving media, e.g. the time between the end of the media stream or a PAUSE request and the new PLAY request. In these cases the RTP sequence number would normally be monotonically increasing across the gap. For RTSP sessions with media that lacks random access properties, like live streams, any media clock jump is commonly result of correspondingly long pause of delivery. The RTP timestamp will have increased in direct proportion to the duration of the paused delivery. Not also that in this case the RTP sequence number should be the next packet number. If not, the RTCP packet loss reporting will indicate as loss all packets not received between the point of pausing and later resuming. This may trigger congestion avoidance mechanisms. The goal when handling jumps in media clock time is that the provided stream is continuous without gaps in RTP timestamp or sequence number. However, when delivery has been halted for some reason the RTP timestamp when resuming SHALL represent the duration the delivery was halted. RTP sequence number MUST be the next number. A client can not rely on that a server will align when resuming playing even if it is RECOMMENDED. The RTP-Info header will provide information if this have occurred or not. We cannot assume that the RTSP client can communicate with the RTP media agent, as the two may be independent processes. If the RTP timestamp shows the same gap as the NPT, the media agent will assume that there is a pause in the presentation. If the jump in NPT is large enough, the RTP timestamp may roll over and the media agent may believe later packets to be duplicates of packets just played out. Having the RTP timestamp jump will also affect the RTCP measurements based on this. Schulzrinne, et al. Expires May 7, 2009 [Page 218] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 As an example, assume a RTP timestamp frequency of 8000 Hz, a packetization interval of 100 ms and an initial sequence number and timestamp of zero. C->S: PLAY rtsp://example.com/fizzle RTSP/2.0 CSeq: 4 Session: abcdefg Range: npt=10-15 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 4 Session: abcdefg Range: npt=10-15 RTP-Info: url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=0;rtptime=0 The ensuing RTP data stream is depicted below: S -> C: RTP packet - seq = 0, rtptime = 0, NPT time = 10s S -> C: RTP packet - seq = 1, rtptime = 800, NPT time = 10.1s . . . S -> C: RTP packet - seq = 49, rtptime = 39200, NPT time = 14.9s Immediately after the end of the play range, the client follows up with a request to PLAY from a new NPT. C->S: PLAY rtsp://example.com/fizzle RTSP/2.0 CSeq: 5 Session: abcdefg Range: npt=18-20 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 5 Session: abcdefg Range: npt=18-20 RTP-Info: url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=50;rtptime=40100 The ensuing RTP data stream is depicted below: S->C: RTP packet - seq = 50, rtptime = 40100, NPT time = 18s S->C: RTP packet - seq = 51, rtptime = 40900, NPT time = 18.1s . . . S->C: RTP packet - seq = 69, rtptime = 55300, NPT time = 19.9s Schulzrinne, et al. Expires May 7, 2009 [Page 219] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 In this example, first, NPT 10 through 15 is played, then the client request the server to skip ahead and play NPT 18 through 20. The first segment is presented as RTP packets with sequence numbers 0 through 49 and timestamp 0 through 39,200. The second segment consists of RTP packets with sequence number 50 through 69, with timestamps 40,100 through 55,200. While there is a gap in the NPT, there is no gap in the sequence number space of the RTP data stream. The RTP timestamp gap is present in the above example due to the time it takes to perform the second play request, in this case 12.5 ms (100/8000). To avoid this gap in playback due to the time it takes to perform RTSP requests, a PLAY request with multiple ranges needs to be specified. That would result in the following example: C->S: PLAY rtsp://example.com/fizzle RTSP/2.0 CSeq: 4 Session: abcdefg Range: npt=10-15;npt=18-20 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 4 Session: abcdefg Range: npt=10-15 RTP-Info: url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=0;rtptime=0 The ensuing RTP data stream is depicted below: S -> C: RTP packet - seq = 0, rtptime = 0, NPT time = 10s S -> C: RTP packet - seq = 1, rtptime = 800, NPT time = 10.1s . . . S -> C: RTP packet - seq = 49, rtptime = 39200, NPT time = 14.9s S -> C: RTP packet - seq = 50, rtptime = 40100, NPT time = 18s S -> C: RTP packet - seq = 51, rtptime = 40900, NPT time = 18.1s . . . S -> C: RTP packet - seq = 69, rtptime = 55300, NPT time = 19.9s C.2.4. Handling RTP Timestamps after PAUSE During a PAUSE / PLAY interaction in an RTSP session, the duration of time for which the RTP transmission was halted MUST be reflected in the RTP timestamp of each RTP stream. The duration can be calculated for each RTP stream as the time elapsed from when the last RTP packet was sent before the PAUSE request was received and when the first RTP packet was sent after the subsequent PLAY request was received. The Schulzrinne, et al. Expires May 7, 2009 [Page 220] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 duration includes all latency incurred and processing time required to complete the request. The RTP RFC [RFC3550] states that: The RTP timestamp for each unit[packet] would be related to the wallclock time at which the unit becomes current on the virtual presentation timeline. In order to satisfy the requirements of [RFC3550], the RTP timestamp space needs to increase continuously with real time. While this is not optimal for stored media, it is required for RTP and RTCP to function as intended. Using a continuous RTP timestamp space allows the same timestamp model for both stored and live media and allows better opportunity to integrate both types of media under a single control. As an example, assume a clock frequency of 8000 Hz, a packetization interval of 100 ms and an initial sequence number and timestamp of zero. C->S: PLAY rtsp://example.com/fizzle RTSP/2.0 CSeq: 4 Session: abcdefg Range: npt=10-15 User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 4 Session: abcdefg Range: npt=10-15 RTP-Info: url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=0;rtptime=0 The ensuing RTP data stream is depicted below: S -> C: RTP packet - seq = 0, rtptime = 0, NPT time = 10s S -> C: RTP packet - seq = 1, rtptime = 800, NPT time = 10.1s S -> C: RTP packet - seq = 2, rtptime = 1600, NPT time = 10.2s S -> C: RTP packet - seq = 3, rtptime = 2400, NPT time = 10.3s The client then sends a PAUSE request: Schulzrinne, et al. Expires May 7, 2009 [Page 221] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C->S: PAUSE rtsp://example.com/fizzle RTSP/2.0 CSeq: 5 Session: abdcdefg User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 5 Session: abcdefg Range: npt=10.4-15 20 seconds elapse and then the client sends a PLAY request. In addition the server requires 15 ms to process the request: C->S: PLAY rtsp://example.com/fizzle RTSP/2.0 CSeq: 6 Session: abcdefg User-Agent: PhonyClient/1.2 S->C: RTSP/2.0 200 OK CSeq: 6 Session: abcdefg Range: npt=10.4-15 RTP-Info: url="rtsp://example.com/fizzle/audiotrack" ssrc=0D12F123:seq=4;rtptime=164400 The ensuing RTP data stream is depicted below: S -> C: RTP packet - seq = 4, rtptime = 164400, NPT time = 10.4s S -> C: RTP packet - seq = 5, rtptime = 165200, NPT time = 10.5s S -> C: RTP packet - seq = 6, rtptime = 166000, NPT time = 10.6s First, NPT 10 through 10.3 is played, then a PAUSE is received by the server. After 20 seconds a PLAY is received by the server which take 15ms to process. The duration of time for which the session was paused is reflected in the RTP timestamp of the RTP packets sent after this PLAY request. A client can use the RTSP range header and RTP-Info header to map NPT time of a presentation with the RTP timestamp. Note: In RFC 2326 [RFC2326], this matter was not clearly defined and was misunderstood commonly. However for RTSP 2.0 it is expected that this will be handled correctly and no exception handling will be required. Schulzrinne, et al. Expires May 7, 2009 [Page 222] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 C.2.5. RTSP / RTP Integration For certain datatypes, tight integration between the RTSP layer and the RTP layer will be necessary. This by no means precludes the above restrictions. Combined RTSP/RTP media clients should use the RTP-Info field to determine whether incoming RTP packets were sent before or after a seek or before or after a PAUSE. C.2.6. Scaling with RTP For scaling (see Section 16.44), RTP timestamps should correspond to the playback timing. For example, when playing video recorded at 30 frames/second at a scale of two and speed (Section 16.46) of one, the server would drop every second frame to maintain and deliver video packets with the normal timestamp spacing of 3,000 per frame, but NPT would increase by 1/15 second for each video frame. Note: The above scaling puts requirements on the media codec or a media stream to support it. For example motion JPEG or other non- predictive video coding can easier handle the above example. C.2.7. Maintaining NPT synchronization with RTP timestamps The client can maintain a correct display of NPT (Normal Play Time) by noting the RTP timestamp value of the first packet arriving after repositioning. The sequence parameter of the RTP-Info (Section 16.43) header provides the first sequence number of the next segment. C.2.8. Continuous Audio For continuous audio, the server SHOULD set the RTP marker bit at the beginning of serving a new PLAY request or at jumps in timeline. This allows the client to perform playout delay adaptation. C.2.9. Multiple Sources in an RTP Session Note that more than one SSRC MAY be sent in the media stream. If it happens all sources are expected to be rendered simultaneously. C.2.10. Usage of SSRCs and the RTCP BYE Message During an RTSP Session The RTCP BYE message indicates the end of use of a given SSRC. If all sources leave an RTP session, it can, in most cases, be assumed to have ended. Therefore, a client or server SHALL NOT send a RTCP BYE message until it has finished using a SSRC. A server SHOULD keep using a SSRC until the RTP session is terminated. Prolonging the use of a SSRC allows the established synchronization context associated Schulzrinne, et al. Expires May 7, 2009 [Page 223] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 with that SSRC to be used to synchronize subsequent PLAY requests even if the PLAY response is late. An SSRC collision with the SSRC that transmits media does also have consequences, as it will force the media sender to change its SSRC in accordance with the RTP specification[RFC3550]. This will result in a loss of synchronization context, and require any receiver to wait for RTCP sender reports for all media requiring synchronization before being able to play out synchronized. Due to these reasons a client joining a session should take care to not select the same SSRC as the server. Any SSRC signalled in the Transport header SHOULD be avoided. A client detecting a collision prior to sending any RTP or RTCP messages can also select a new SSRC. C.3. Future Additions It is the intention that any future protocol or profile regarding both for media delivery and lower transport should be easy to add to RTSP. This section provides the necessary steps that needs to be meet. The following things needs to be considered when adding a new protocol of profile for use with RTSP: o The protocol or profile needs to define a name tag representing it. This tag is required to be a ABNF "token" to be possible to use in the Transport header specification. o The useful combinations of protocol, profiles and lower layer transport for this extension needs to be defined. For each combination declare the necessary parameters to use in the Transport header. o For new media protocols the interaction with RTSP needs to be addressed. One important factor will be the media synchronization. May need new headers similar to RTP info to carry information. o Discuss congestion control for media, especially if transport without built in congestion control is used. See the IANA section (Section 22) for information how to register new attributes. Schulzrinne, et al. Expires May 7, 2009 [Page 224] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix D. Use of SDP for RTSP Session Descriptions The Session Description Protocol (SDP, [RFC4566]) may be used to describe streams or presentations in RTSP. This description is typically returned in reply to a DESCRIBE request on an URI from a server to a client, or received via HTTP from a server to a client. This appendix describes how an SDP file determines the operation of an RTSP session. SDP as is provides no mechanism by which a client can distinguish, without human guidance, between several media streams to be rendered simultaneously and a set of alternatives (e.g., two audio streams spoken in different languages). However the SDP extension "Grouping of Media Lines in the Session Description Protocol (SDP)" [RFC3388] may provide such functionality depending on need. Also future grouping semantics may in the future be developed. D.1. Definitions The terms "session-level", "media-level" and other key/attribute names and values used in this appendix are to be used as defined in SDP (RFC 4566 [RFC4566]): D.1.1. Control URI The "a=control:" attribute is used to convey the control URI. This attribute is used both for the session and media descriptions. If used for individual media, it indicates the URI to be used for controlling that particular media stream. If found at the session level, the attribute indicates the URI for aggregate control (presentation URI). The session level URI SHALL be different from any media level URI. The presence of a session level control attribute SHALL be interpreted as support for aggregated control. The control attribute SHALL be present on media level unless the presentation only contains a single media stream, in which case the attribute MAY only be present on the session level. ABNF for the attribute is defined in Section 20.3. Example: a=control:rtsp://example.com/foo This attribute MAY contain either relative or absolute URIs, following the rules and conventions set out in RFC 3986 [RFC3986]. Implementations SHALL look for a base URI in the following order: 1. the RTSP Content-Base field; Schulzrinne, et al. Expires May 7, 2009 [Page 225] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 2. the RTSP Content-Location field; 3. the RTSP Request-URI. If this attribute contains only an asterisk (*), then the URI SHALL be treated as if it were an empty embedded URI, and thus inherit the entire base URI. Note, RFC 2326 was very unclear on the processing of relative URI and several RTSP 1.0 implementations at the point of publishing this document did not perform RFC 3986 processing to determine the resulting URI, instead simple concatenation is common. To avoid this issue completely it is recommended to use absolute URI in the SDP. The URI handling for SDPs from container files need special consideration. For example lets assume that a container file has the URI: "rtsp://example.com/container.mp4". Lets further assume this URI is the base URI, and that there is a absolute media level URI: "rtsp://example.com/container.mp4/trackID=2". A relative media level URI that resolves in accordance with RFC 3986 [RFC3986] to the above given media URI is: "container.mp4/trackID=2". It is usually not desirable to need to include in or modify the SDP stored within the container file with the server local name of the container file. To avoid this, one can modify the base URI used to include a trailing slash, e.g. "rtsp://example.com/container.mp4/". In this case the relative URI for the media will only need to be: "trackID=2". However this will also mean that using "*" in the SDP will result in control URI including the trailing slash, i.e. "rtsp://example.com/container.mp4/". Note: The usage of TrackID in the above is not an standardized form, but one example out of several similar strings such as TrackID, Track_ID, StreamID that is used by different server vendors to indicate a particular piece of media inside a container file. D.1.2. Media Streams The "m=" field is used to enumerate the streams. It is expected that all the specified streams will be rendered with appropriate synchronization. If the session is over multicast, the port number indicated SHOULD be used for reception. The client MAY try to override the destination port, through the Transport header. The servers MAY allow this, the response will indicate if allowed or not. If the session is unicast, the port number is the ones RECOMMENDED by the server to the client, about which receiver ports to use; the client MUST still include its receiver ports in its SETUP request. Schulzrinne, et al. Expires May 7, 2009 [Page 226] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The client MAY ignore this recommendation. If the server has no preference, it SHOULD set the port number value to zero. The "m=" lines contain information about what transport protocol, profile, and possibly lower-layer is to be used for the media stream. The combination of transport, profile and lower layer, like RTP/AVP/ UDP needs to be defined for how to be used with RTSP. The currently defined combinations are defined in Appendix C, further combinations MAY be specified. Usage of grouping of media lines [RFC3388] to determine which media lines should or should not be included in a RTSP session is unspecified. Example: m=audio 0 RTP/AVP 31 D.1.3. Payload Type(s) The payload type(s) are specified in the "m=" line. In case the payload type is a static payload type from RFC 3551 [RFC3551], no other information may be required. In case it is a dynamic payload type, the media attribute "rtpmap" is used to specify what the media is. The "encoding name" within the "rtpmap" attribute may be one of those specified in RFC 3551 (Sections 5 and 6), or an MIME type registered with IANA, or an experimental encoding as specified in SDP (RFC 4566 [RFC4566]). Codec-specific parameters are not specified in this field, but rather in the "fmtp" attribute described below. D.1.4. Format-Specific Parameters Format-specific parameters are conveyed using the "fmtp" media attribute. The syntax of the "fmtp" attribute is specific to the encoding(s) that the attribute refers to. Note that some of the format specific parameters may be specified outside of the fmtp parameters, like for example the "ptime" attribute for most audio encodings. D.1.5. Directionality of media stream The SDP attributes "a=sendrecv", "a=recvonly" and "a=sendonly" provides instructions on which direction the media streams flow within a session. When using RTSP the SDP can be delivered to a client using either RTSP DESCRIBE or a number of RTSP external methods, like HTTP, FTP, and email. Based on this the SDP applies to how the RTSP client will see the complete session. Thus for media streams delivered from the RTSP server to the client would be given the "a=recvonly" attribute. Schulzrinne, et al. Expires May 7, 2009 [Page 227] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 The direction attributes are not commonly used in SDPs for RTSP, but may occur. "a=recvonly" in a SDP provided to the RTSP client SHALL indicate that media delivery will only occur in the direction from the RTSP server to the client. In SDP provided to the RTSP client that lacks any of the directionality attributes (a=recvonly, a=sendonly, a=sendrecv) SHALL behave as if the "a=recvonly" attribute was received. Note that this overrules the normal default rule defined in SDP[RFC4566]. The usage of "a=sendonly" or "a=sendrecv" is not defined, nor is the interpretation of SDP by other entities than the RTSP client. D.1.6. Range of Presentation The "a=range" attribute defines the total time range of the stored session or an individual media. Non-seekable live sessions can be indicated, while the length of live sessions can be deduced from the "t" and "r" SDP parameters. The attribute is both a session and a media level attribute. For presentations that contains media streams of the same durations, the range attribute SHOULD only be used at session-level. In case of different length the range attribute MUST be given at media level for all media, and SHOULD NOT be given at session level. If the attribute is present at both media level and session level the media level values SHALL be used. Note: Usually one will specify the same length for all media, even if there isn't media available for the full duration on all media. However that requires that the server accepts PLAY requests within that range. Servers SHALL take care to provide RTSP Range (see Section 16.38) values that are consistent with what is presented in the SDP for the content. There are no reason for non dynamic content, like media clips provided on demand to have inconsistent values. Inconsistent values between the SDP and the actual values for the content handled by the server is likely to generate some failure, like 457 "Invalid Range", in case the client uses PLAY requests with a Range header. In case the content is dynamic in length and it is infeasible to provide a correct value in the SDP the server is recommended to describe this as non-seekable content (see below). The server MAY override that property in the response to a PLAY request using the correct values in the Range header. The unit is specified first, followed by the value range. The units and their values are as defined in Section 4.4, Section 4.5 and Section 4.6 and MAY be extended with further formats. Any open ended range (start-), i.e. without stop range, is of unspecified duration Schulzrinne, et al. Expires May 7, 2009 [Page 228] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 and SHALL be considered as non-seekable content unless this property is overridden. Multiple instances carrying different clock formats MAY be included at either session or media level. ABNF for the attribute is defined in Section 20.3. Examples: a=range:npt=0-34.4368 a=range:clock=19971113T211503Z-19971113T220300Z Non seekable stream of unknown duration: a=range:npt=0- D.1.7. Time of Availability The "t=" field MUST contain suitable values for the start and stop times for both aggregate and non-aggregate stream control. The server SHOULD indicate a stop time value for which it guarantees the description to be valid, and a start time that is equal to or before the time at which the DESCRIBE request was received. It MAY also indicate start and stop times of 0, meaning that the session is always available. For sessions that are of live type, i.e. specific start time, unknown stop time, likely unseekable, the "t=" and "r=" field SHOULD be used to indicate the start time of the event. The stop time SHOULD be given so that the live event will have ended at that time, while still not be unnecessary long into the future. D.1.8. Connection Information In SDP, the "c=" field contains the destination address for the media stream. For on-demand unicast streams and some multicast streams, the destination address MAY be specified by the client via the SETUP request, thus overriding any specified address. To identify streams without a fixed destination address, where the client is required to specify a destination address, the "c=" field SHOULD be set to a null value. For addresses of type "IP4", this value SHALL be "0.0.0.0", and for type "IP6", this value SHALL be "0:0:0:0:0:0:0:0", i.e. the unspecified address according to RFC 4291 [RFC4291]. D.1.9. Entity Tag The optional "a=etag" attribute identifies a version of the session description. It is opaque to the client. SETUP requests may include this identifier in the If-Match field (see Section 16.24) to only allow session establishment if this attribute value still corresponds to that of the current description. The attribute value is opaque and may contain any character allowed within SDP attribute values. Schulzrinne, et al. Expires May 7, 2009 [Page 229] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 ABNF for the attribute is defined in Section 20.3. Example: a=etag:"158bb3e7c7fd62ce67f12b533f06b83a" One could argue that the "o=" field provides identical functionality. However, it does so in a manner that would put constraints on servers that need to support multiple session description types other than SDP for the same piece of media content. D.2. Aggregate Control Not Available If a presentation does not support aggregate control no session level "a=control:" attribute is specified. For a SDP with multiple media sections specified, each section will have its own control URI specified via the "a=control:" attribute. Example: v=0 o=- 2890844256 2890842807 IN IP4 192.0.2.56 s=I came from a web page e=adm@example.com c=IN IP4 0.0.0.0 t=0 0 m=video 8002 RTP/AVP 31 a=control:rtsp://audio.com/movie.aud m=audio 8004 RTP/AVP 3 a=control:rtsp://video.com/movie.vid Note that the position of the control URI in the description implies that the client establishes separate RTSP control sessions to the servers audio.com and video.com. It is recommended that an SDP file contains the complete media initialization information even if it is delivered to the media client through non-RTSP means. This is necessary as there is no mechanism to indicate that the client should request more detailed media stream information via DESCRIBE. D.3. Aggregate Control Available In this scenario, the server has multiple streams that can be controlled as a whole. In this case, there are both a media-level "a=control:" attributes, which are used to specify the stream URIs, and a session-level "a=control:" attribute which is used as the Request-URI for aggregate control. If the media-level URI is relative, it is resolved to absolute URIs according to Appendix D.1.1 Schulzrinne, et al. Expires May 7, 2009 [Page 230] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 above. Example: C->M: DESCRIBE rtsp://example.com/movie RTSP/2.0 CSeq: 1 User-Agent: PhonyClient/1.2 M->C: RTSP/2.0 200 OK CSeq: 1 Date: Thu, 23 Jan 1997 15:35:06 GMT Content-Type: application/sdp Content-Base: rtsp://example.com/movie/ Content-Length: 227 v=0 o=- 2890844256 2890842807 IN IP4 192.0.2.211 s=I contain i= e=adm@example.com c=IN IP4 0.0.0.0 a=control:* t=0 0 m=video 8002 RTP/AVP 31 a=control:trackID=1 m=audio 8004 RTP/AVP 3 a=control:trackID=2 In this example, the client is required to establish a single RTSP session to the server, and uses the URIs rtsp://example.com/movie/trackID=1 and rtsp://example.com/movie/trackID=2 to set up the video and audio streams, respectively. The URI rtsp://example.com/movie/, which is resolved from the "*", controls the whole presentation (movie). A client is not required to issues SETUP requests for all streams within an aggregate object. Servers should allow the client to ask for only a subset of the streams. D.4. RTSP external SDP delivery There are some considerations that needs to be made when the session description is delivered to client outside of RTSP, for example in HTTP or email. First of all the SDP needs to contain absolute URIs, relative will in most cases not work as the delivery will not correctly forward the base URI. And as SDP might be temporarily stored on file system before being loaded into an RTSP capable client, thus if possible to Schulzrinne, et al. Expires May 7, 2009 [Page 231] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 transport the base URI it still would need to be merged into the file. The writing of the SDP session availability information, i.e. "t=" and "r=", needs to be carefully considered. When the SDP is fetched by the DESCRIBE method, the probability that it is valid is very high. However the same are much less certain for SDPs distributed using other methods. Therefore the publisher of the SDP should take care to follow the recommendations about availability in the SDP specification [RFC4566]. Schulzrinne, et al. Expires May 7, 2009 [Page 232] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix E. Text format for Parameters A resource of type "text/parameters" consists of either 1) a list of parameters (for a query) or 2) a list of parameters and associated values (for an response or setting of the parameter). Each entry of the list is a single line of text. Parameters are separated from values by a colon. The parameter name SHALL only use US-ASCII visable characters while the values are UTF-8 text strings. The media type registration template is in Section 22.15. There exist a potential interoperability issue for this format. It was named in RFC 2326 but never defined, even if used in examples that hint at the syntax. This format matches the purpose and its syntax supports the examples provided. However, it goes further by allowing UTF-8 in the vaue part, thus usage of UTF-8 strings may not be supported. However, as individual parameters are not defined, the using application anyway needs to have out-of-band agreement or using feature-tag to determine if the end-point supports the parameters. The ABNF [RFC5234] grammar for "text/parameters" content is: file = *((parameter / parameter-value) CRLF) parameter = 1*visible-except-colon parameter-value = parameter *WSP ":" value visible-except-colon = %x21-39 / %x3B-7E ; VCHAR - ":" value = *(TEXT-UTF8char / WSP) TEXT-UTF8char = %x21-7E / UTF8-NONASCII UTF8-NONASCII = %xC0-DF 1UTF8-CONT / %xE0-EF 2UTF8-CONT / %xF0-F7 3UTF8-CONT / %xF8-FB 4UTF8-CONT / %xFC-FD 5UTF8-CONT UTF8-CONT = %x80-BF WSP = ; Space or HTAB VCHAR = CRLF = Schulzrinne, et al. Expires May 7, 2009 [Page 233] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix F. Requirements for Unreliable Transport of RTSP This section provides anyone intending to define how to transport of RTSP messages over a unreliable transport protocol with some information learned by the attempt in RFC 2326 [RFC2326]. RFC 2326 define both an URI scheme and some basic functionality for transport of RTSP messages over UDP, however it was not sufficient for reliable usage and successful interoperability. The RTSP scheme defined for unreliable transport of RTSP messages was "rtspu". It has been reserved by this specification as at least one commercial implementation exist, thus avoiding any collisions in the name space. The following considerations should exist for operation of RTSP over an unreliable transport protocol: o Request shall be acknowledged by the receiver. If there is no acknowledgement, the sender may resend the same message after a timeout of one round-trip time (RTT). Any retransmissions due to lack of acknowledgement must carry the same sequence number as the original request. o The round-trip time can be estimated as in TCP (RFC 1123) [RFC1123], with an initial round-trip value of 500 ms. An implementation may cache the last RTT measurement as the initial value for future connections. o If RTSP is used over a small-RTT LAN, standard procedures for optimizing initial TCP round trip estimates, such as those used in T/TCP (RFC 1644) [RFC1644], can be beneficial. o The Timestamp header (Section 16.50) is used to avoid the retransmission ambiguity problem [Stevens98]. o The registered default port for RTSP over UDP for the server is 554. o RTSP messages can be carried over any lower-layer transport protocol that is 8-bit clean. o RTSP messages are vulnerable to bit errors and should not be subjected to them. o Source authentication, or at least validation that RTSP messages comes from the same entity becomes extremely important, as session hijacking may be substantially easier for RTSP message transport using an unreliable protocol like UDP than for TCP. Schulzrinne, et al. Expires May 7, 2009 [Page 234] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 There exist two RTSP headers thats primarily are intended for being used by the unreliable handling of RTSP messages and which will be maintained: o [CSeq] See Section 16.19 o [Timestamp] See Section 16.50 Schulzrinne, et al. Expires May 7, 2009 [Page 235] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix G. Backwards Compatibility Considerations This section contains notes on issues about backwards compatibility with clients or servers being implemented according to RFC 2326 [RFC2326]. Note that there exist no requirement to implement RTSP 1.0, in fact we recommend against it as it is difficult to do in an interoperable way. A server implementing RTSP/2.0 MUST include a RTSP-Version of RTSP/2.0 in all responses to requests containing RTSP-Version RTSP/2.0. If a server receives a RTSP/1.0 request, it MAY respond with a RTSP/1.0 response if it chooses to support RFC 2326. If the server chooses not to support RFC 2326, it SHALL respond with a 505 (RTSP Version not supported) status code. A server MUST NOT respond to a RTSP-Version RTSP/1.0 request with a RTSP-Version RTSP/2.0 response. Clients implementing RTSP/2.0 MAY use an OPTIONS request with a RTSP- Version of 2.0 to determine whether a server supports RTSP/2.0. If the server responds with either a RTSP-Version of 1.0 or a status code of 505 (RTSP Version not supported), the client will have to use RTSP/1.0 requests if it chooses to support RFC 2326. G.1. Play Request in Play mode The behavior in the server when a Play is received in Play mode has changed (Section 13.4). In RFC 2326, the new PLAY request would be queued until the current Play completed. Any new PLAY request now take effect immediately replacing the previous request. G.2. Using Persistent Connections Some server implementations of RFC 2326 maintain a one-to-one relationship between a connection and an RTSP session. Such implementations require clients to use a persistent connection to communicate with the server and when a client closes its connection, the server may remove the RTSP session. This is worth noting if a RTSP 2.0 client also supporting 1.0 connects to a 1.0 server. Schulzrinne, et al. Expires May 7, 2009 [Page 236] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix H. Open Issues Open issues are filed and tracked in the bug and feature trackers at http://rtspspec.sourceforge.net. Open issues are discussed on MMUSIC list. Schulzrinne, et al. Expires May 7, 2009 [Page 237] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix I. Changes Compared to RTSP 1.0 (RFC 2326), the below changes has been made when defining RTSP 2.0. Note that this list does not reflect minor changes in wording or correction of typographical errors. o The section on minimal implementation was deleted without substitution. o The Transport header has been changed in the following way: * The ABNF has been changed to define that extensions are possible, and that unknown extension parameters are to be ignored. * To prevent backwards compatibility issues, any extension or new parameter requires the usage of a feature-tag combined with the Require header. * Syntax unclarities with the Mode parameter has been resolved. * Syntax error with ";" for multicast and unicast has been resolved. * Two new addressing parameters has been defined, src_addr and dest_addr. These replaces the parameters "port", "client_port", "server_port", "destination", "source". * Support for IPv6 explicit addresses in all address fields has been included. * To handle URI definitions that contain ";" or "," a quoted URI format has been introduced and is required. * Defined IANA registries for the transport headers parameters, transport-protocol, profile, lower-transport, and mode. * The transport headers interleaved parameter's text was made more strict and use formal requirements levels. It was also clarified that the interleaved channels are symmetric and that it is the server that sets the channel numbers. * It has been clarified that the client can't request of the server to use a certain RTP SSRC, using a request with the transport parameter SSRC. * Syntax definition for SSRC has been clarified to require 8HEX. It has also been extend to allow multiple values for clients Schulzrinne, et al. Expires May 7, 2009 [Page 238] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 supporting this version. * Clarified the text on the transport headers "dest_addr" parameters regarding what security precautions the server is required to perform. o The Range formats has been changed in the following way: * The NPT format has been given a initial NPT identifier that must now be used. * All formats now support initial open ended formats of type "npt=-10". o RTSP message handling has been changed in the following way: * RTSP messages now uses URIs rather then URLs. * It has been clarified that a 4xx message due to missing CSeq header shall be returned without a CSeq header. * Rules for how to handle timing out RTSP messages has been added. * Extended Pipelining rules allowing for quick session startup. o The HTTP references has been updated to RFC 2616 and RFC 2617. This has resulted in that the Public, and the Content-Base header needed to be defined in the RTSP specification. Known effects on RTSP due to HTTP clarifications: * Content-Encoding header can include encoding of type "identity". o The state machine section has completely been rewritten. It includes now more details and are also more clear about the model used. o A IANA section has been included with contains a number of registries and their rules. This will allow us to use IANA to keep track of RTSP extensions. o Than transport of RTSP messages has seen the following changes: * The use of UDP for RTSP message transport has been deprecated due to missing interest and to broken specification. Schulzrinne, et al. Expires May 7, 2009 [Page 239] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 * The rules for how TCP connections is to be handled has been clarified. Now it is made clear that servers should not close the TCP connection unless they have been unused for significant time. * Strong recommendations why server and clients should use persistent connections has also been added. * There is now a requirement on the servers to handle non- persistent connections as this provides fault tolerance. * Added wording on the usage of Connection:Close for RTSP. * specified usage of TLS for RTSP messages, including a scheme to approve a proxies TLS connection to the next hop. o The following header related changes have been made: * Accept-Ranges response header is added. This header clarifies which range formats that can be used for a resource. * Changed the Range header to allow multiple ranges for creating editing list. * Fixed the missing definitions for the Cache-Control header. Also added to the syntax definition the missing delta-seconds for max-stale and min-fresh parameters. * Put requirement on CSeq header that the value is increased by one for each new RTSP request. A Recommendation to start at 1 has also been added. * Added requirement that the Date header must be used for all messages with entity and the Server should always include it. * Removed possibility of using Range header with Scale header to indicate when it is to be activated, since it can't work as defined. Also added rule that lack of Scale header in response indicates lack of support for the header. Feature-tags for scaled playback has been defined. * The Speed header must now be responded to indicate support and the actual speed going to be used. A feature-tag is defined. Notes on congestion control was also added. * The Supported header was borrowed from SIP to help with the feature negotiation in RTSP. Schulzrinne, et al. Expires May 7, 2009 [Page 240] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 * Clarified that the Timestamp header can be used to resolve retransmission ambiguities. * The Session header text has been expanded with a explanation on keep alive and which methods to use. SET_PARAMETER is now recommended to use if only keep-alive within RTSP is desired. * It has been clarified how the Range header formats is used to indicate pause points in the PAUSE response. * Clarified that RTP-Info URIs that are relative, uses the Request-URI as base URI. Also clarified that used URI must be that one that was used in the SETUP request. They are now also required to be quoted. The header also expresses the SSRC for the provided RTP timestamp and sequence number values. * Added text that requires the Range to always be present in PLAY responses. Clarified what should be sent in case of live streams. * The headers table has been updated using a structured borrowed from SIP. Those tables carries much more information and should provide a good overview of the available headers. * It has been is clarified that any message with a message body is required to have a Content-Length header. This was the case in RFC 2326 but could be misinterpreted. * To resolve functionality around ETag. The ETag and If-None- Match header has been added from HTTP with necessary clarification in regards to RTSP operation. * Imported the Public header from HTTP RFC 2068 [RFC2068] since it has been removed from HTTP due to lack of use. Public is used quite frequently in RTSP. * Clarified rules for populating the Public header so that it is an intersection of the capabilities of all the RTSP agents in a chain. * Added the Media-Range header for listing the current availability of the media range. * Added the Notify-Reason header for giving the reason when sending PLAY_NOTIFY requests. Schulzrinne, et al. Expires May 7, 2009 [Page 241] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o The Protocol Syntax has been changed in the following way: * All BNF definitions are updated according to the rules defined in RFC 5234 [RFC5234] and has been gathered in a separate Section 20. * The BNF for the User-Agent and Server headers has been corrected so now only the description is in the HTTP specification. * Some definitions in the introduction regarding the RTSP session has been changed. * The protocol has been made fully IPv6 capable. Certain of the functionality, like using explicit IPv6 addresses in fields requires that the protocol support this updated specification. * Added a fragment part to the RTSP URI. This seem to be indicated by the note below the definition however it was not part of the BNF. * The CHAR rule has been changed to exclude NULL. o The Status codes has been changed in the following way: * The use of status code 303 "See Other" has been deprecated as it does not make sense to use in RTSP. * When sending response 451 and 458 the response body should contain the offending parameters. * Clarification on when a 3rr redirect status code can be received has been added. This includes receiving 3rr as a result of request within a established session. This provides clarification to a previous unspecified behavior. * Removed the 201 (Created) and 250 (Low On Storage Space) status codes as they are only relevant to recording, which is deprecated. o The following functionality has been deprecated from the protocol: * The use of Queued Play. * The use of PLAY method for keep-alive in play state. * The RECORD and ANNOUNCE methods and all related functionality. Some of the syntax has been removed. Schulzrinne, et al. Expires May 7, 2009 [Page 242] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 * The possibility to use timed execution of methods with the time parameter in the Range header. * The description on how rtspu works is not part of the core specification and will require external description. Only that it exist is defined here and some requirements for the the transport is provided. o The following changes has been made in relation to methods: * The OPTIONS method has been clarified with regards to the use of the Public and Allow headers. * The RECORD and ANNOUNCE methods are removed as they are lacking implementation and not considered necessary in the core specification. Any work on these methods should be done as a extension document to RTSP. * Added text clarifying the usage of SET_PARAMETER for keep-alive and usage without any body. * PLAY method is now allowed to be pipelined with the pipelining of one or more SETUP requests following the initial that generates the session for aggregated control. o Wrote a new section about how to setup different media transport alternatives and their profiles, and lower layer protocols. This resulted that the appendix on RTP interaction was moved there instead in the part describing RTP. The section also includes guidelines what to think of when writing usage guidelines for new protocols and profiles. o Setup and usage of independent TCP connections for transport of RTP has been specified. o Added a new section describing the available mechanisms to determine if functionality is supported, called "Capability Handling". Renamed option-tags to feature-tags. o Added a contributors section with people who have contributed actual text to the specification. o Added a section Use Cases that describes the major use cases for RTSP. o Clarified the usage of a=range and how to indicate live content that are not seekable with this header. Schulzrinne, et al. Expires May 7, 2009 [Page 243] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o Text specifying the special behavior of PLAY for live content. o Added a new method PLAY_NOTIFY. This method is used by the RTSP server to asynchronously notify clients about session changes. Schulzrinne, et al. Expires May 7, 2009 [Page 244] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix J. Acknowledgements This memorandum defines RTSP version 2.0 which is a revision of the Proposed Standard RTSP version 1.0 which is defined in [RFC2326]. The authors of this RFC are Henning Schulzrinne, Anup Rao, and Robert Lanphier. Both RTSP version 1.0 and RTSP versio 2.0 borrow format and descriptions from HTTP/1.1. This document has benefited greatly from the comments of all those participating in the MMUSIC-WG. In addition to those already mentioned, the following individuals have contributed to this specification: Rahul Agarwal, Jeff Ayars, Milko Boic, Torsten Braun, Brent Browning, Bruce Butterfield, Steve Casner, Francisco Cortes, Kelly Djahandari, Martin Dunsmuir, Eric Fleischman, Jay Geagan, Andy Grignon, V. Guruprasad, Peter Haight, Mark Handley, Brad Hefta-Gaub, Volker Hilt, John K. Ho, Go Hori, Philipp Hoschka, Anne Jones, Anders Klemets, Ruth Lang, Stephanie Leif, Jonathan Lennox, Eduardo F. Llach, Thomas Marshall, Rob McCool, David Oran, Joerg Ott, Maria Papadopouli, Sujal Patel, Ema Patki, Alagu Periyannan, Colin Perkins, Igor Plotnikov, Jonathan Sergent, Pinaki Shah, David Singer, Lior Sion, Jeff Smith, Alexander Sokolsky, Dale Stammen, John Francis Stracke, Maureen Chesire, David Walker, Geetha Srikantan, Stephan Wenger, Pekka Pessi, Jae-Hwan Kim, Holger Schmidt, Stephen Farrell, Xavier Marjou, Joe Pallas and Mela Martti. J.1. Contributors The following people have made written contributions that were included in the specification: o Tom Marshall contributed text on the usage of 3rr status codes. o Thomas Zheng contributed text on the usage of the Range in PLAY responses. o Sean Sheedy contributed text on the timeout behavior of RTSP messages and connections, and the 463 status code. o Fredrik Lindholm contributed text about the RTSP security framework. o John Lazzaro contributed the text for RTP over Independent TCP. Schulzrinne, et al. Expires May 7, 2009 [Page 245] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 o Aravind Narasimhan contributed by rewriting Media Transport Alternatives (Appendix C) and editorial improvements on a number of places in the specification. Schulzrinne, et al. Expires May 7, 2009 [Page 246] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Appendix K. RFC Editor Consideration Please replace RFC XXXX with the RFC number this specification recieves. Schulzrinne, et al. Expires May 7, 2009 [Page 247] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Authors' Addresses Henning Schulzrinne Columbia University 1214 Amsterdam Avenue New York, NY 10027 USA Email: schulzrinne@cs.columbia.edu Anup Rao Cisco USA Email: anrao@cisco.com Rob Lanphier Seattle, WA USA Email: robla@robla.net Magnus Westerlund Ericsson AB Faeroegatan 6 STOCKHOLM, SE-164 80 SWEDEN Email: magnus.westerlund@ericsson.com Martin Stiemerling NEC Laboratories Europe, NEC Europe Ltd. Kurfuersten-Anlage 36 Heidelberg 69115 Germany Phone: +49 (0) 6221 4342 113 Email: stiemerling@nw.neclab.eu Schulzrinne, et al. Expires May 7, 2009 [Page 248] Internet-Draft Real Time Streaming Protocol 2.0 (RTSP) November 2008 Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Schulzrinne, et al. Expires May 7, 2009 [Page 249]