IDR W. Hao Q. Liang Internet Draft Huawei Technologies Ltd. Intended status: Standards Track Jim Uttaro AT&T S. Litkowski Orange Business Service S. Zhuang Huawei Technologies Ltd. Expires: November 2015 May 9, 2015 Dissemination of Flow Specification Rules for L2 VPN draft-ietf-idr-flowspec-l2vpn-01.txt Abstract This document defines BGP flow-spec extension for Ethernet traffic filtering in L2 VPN network. SAFI=134 in [RFC5575] is redefined for dissemination traffic filtering information in an L2VPN environment. A new subset of component types and extended community also are defined. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Copyright Notice Copyright (c) 2015 IETF Trust and the persons identified as the document authors. All rights reserved. Hao & Liang,et,al Expires November 9, 2015 [Page 1] Internet-Draft EVPN Flow Spec May 2015 This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction ................................................ 2 2. Layer 2 Flow Specification encoding in BGP................... 3 3. Ethernet Flow Specification encoding in BGP.................. 4 4. Ethernet Flow Specification Traffic Actions.................. 6 5. Security Considerations...................................... 8 6. IANA Considerations ......................................... 8 6.1. Normative References................................... 10 6.2. Informative References................................. 10 7. Acknowledgments ............................................ 10 1. Introduction BGP Flow-spec is an extension to BGP that allows for the dissemination of traffic flow specification rules. It leverages the BGP Control Plane to simplify the distribution of ACLs, new filter rules can be injected to all BGP peers simultaneously without changing router configuration. The typical application of BGP Flow- spec is to automate the distribution of traffic filter lists to routers for DDOS mitigation. RFC5575 defines a new BGP Network Layer Reachability Information (NLRI) format used to distribute traffic flow specification rules. NLRI (AFI=1, SAFI=133)is for IPv4 unicast filtering. NLRI (AFI=1, SAFI=134)is for BGP/MPLS VPN filtering. The Flow specification match part only includes L3/L4 information like source/destination prefix, protocol, ports, and etc, so traffic flows can only be selectively filtered based on L3/L4 information. Layer 2 Virtual Private Networks L2VPNs have already been deployed in an increasing number of networks today. In L2VPN network, we also have requirement to deploy BGP Flow-spec to mitigate DDoS attack traffic. Within L2VPN network, both IP and non-IP Ethernet traffic Hao & Liang,et,al Expires November 9, 2015 [Page 2] Internet-Draft EVPN Flow Spec May 2015 maybe exist. For IP traffic filtering, the Flow specification rules defined in [RFC5575] which include match criteria and actions can still be used, flow specification rules received via new NLRI format apply only to traffic that belongs to the VPN instance(s) in which it is imported. For non-IP Ethernet traffic filtering, Layer 2 related information like source/destination MAC and VLAN should be considered. But the flow specification match criteria defined in RFC5575 only include layer 3 and layer 4 IP information, layer 2 Ethernet information haven't been included. There are different kinds of L2VPN networks like EVPN [EVPN], BGP VPLS [RFC4761], LDP VPLS [RFC4762] and border gateway protocol (BGP) auto discovery [RFC 6074]. Because the flow-spec feature relies on BGP protocol to distribute traffic filtering rules, so it can only be incrementally deployed in those L2VPN networks where BGP is used for auto discovery and/or signaling purposes such as BGP-based VPLS [4761], EVPN and LDP-based VPLS [4762] with BGP auto-discovery [6074]. This draft proposes a new subset of component types and extended community to support L2VPN flow-spec application. SAFI=134 in [RFC5575] is redefined for dissemination traffic filtering information in an L2VPN environment. 2. Layer 2 Flow Specification encoding in BGP The [RFC5575] defines SAFI 133 and SAFI 134 for ''dissemination of IPv4 flow specification rules'' and ''dissemination of VPNv4 flow specification rules'' respectively. [draft-ietf-idr-flow-spec-v6-06] redefines the [RFC5575] SAFIs in order to make them applicable to both IPv4 and IPv6 applications. This document will further redefine the SAFI 134 in order to make them applicable to L2VPN applications. The following changes are defined: ''SAFI 134 for dissemination of L3VPN flow specification rules'' to now be defined as ''SAFI 134 for dissemination of VPN flow specification rules'' For SAFI 134 the indication to which address family it is referring to will be recognized by AFI value (AFI=1 for VPNv4, AFI=2 VPNv6 and AFI=25 for L2VPN). Such modification is fully backwards compatible with existing implementation and production deployments. Hao & Liang,et,al Expires November 9, 2015 [Page 3] Internet-Draft EVPN Flow Spec May 2015 3. Ethernet Flow Specification encoding in BGP The NLRI format for this address family consists of a fixed-length Route Distinguisher field (8 bytes) followed by a flow specification, following the encoding defined in this document. The NLRI length field shall include both the 8 bytes of the Route Distinguisher as well as the subsequent flow specification. Flow specification rules received via this NLRI apply only to traffic that belongs to the VPN instance(s) in which it is imported. Flow rules are accepted by default, when received from remote PE routers. Besides the component types defined in [RFC5575] and [draft-ietf- idr-flow-spec-v6-06], this document proposes the following additional component types for L2VPN Ethernet traffic filtering: Type 14 - Source MAC Encoding: Defines a list of {operation(op), value} pairs used to match source MAC. Values are encoded as 6-byte quantities. The operation field is encoded as ''Numeric operator'' defined in [RFC5575]. Type 15 - Destination MAC Encoding: Defines a list of {operation, value} pairs used to match destination MAC. Values are encoded as 6-byte quantities. Type 16 - Ethernet Type Encoding: Defines a list of {operation, value} pairs used to match two-octet field. Values are encoded as 2-byte quantities. Ethernet II framing defines the two-octet EtherType field in an Ethernet frame, preceded by destination and source MAC addresses, that identifies an upper layer protocol encapsulating the frame data. Type 17 - DSAP(Destination Service Access Point) in LLC Encoding: Hao & Liang,et,al Expires November 9, 2015 [Page 4] Internet-Draft EVPN Flow Spec May 2015 Defines a list of {operation, value} pairs used to match 1-octet DSAP in the 802.2 LLC(Logical Link Control Header). Values are encoded as 1-byte quantities. Type 18 - SSAP(Source Service Access Point) in LLC Encoding: Defines a list of {operation, value} pairs used to match 1-octet SSAP in the 802.2 LLC. Values are encoded as 1-byte quantities. Type 19 - Control field in LLC Encoding: Defines a list of {operation, value} pairs used to match 1-octet control field in the 802.2 LLC. Values are encoded as 1-byte quantities. Type 20 - SNAP Encoding: Defines a list of {operation, value} pairs used to match 5-octet SNAP(Sub-Network Access Protocol) field. Values are encoded as 5- byte quantities. Type 21 - VLAN ID Encoding: Defines a list of {operation, value} pairs used to match VLAN ID. Values are encoded as 1- or 2-byte quantities. In virtual local-area network (VLAN) stacking case, the VLAN ID is outer VLAN ID. Type 22 - VLAN COS Encoding: Defines a list of {operation, value} pairs used to match 3-bit VLAN COS fields [802.1p]. Values are encoded using a single byte, where the five most significant bits are zero and the three least significant bits contain the VLAN COS value. Hao & Liang,et,al Expires November 9, 2015 [Page 5] Internet-Draft EVPN Flow Spec May 2015 In virtual local-area network (VLAN) stacking case, the VLAN COS is outer VLAN COS. Type 23 - Inner VLAN ID Encoding: Defines a list of {operation, value} pairs used to match inner VLAN ID using for virtual local-area network (VLAN) stacking or Q in Q case. Values are encoded as 1- or 2-byte quantities. In single VLAN case, the component type MUST not be used. Type 24 - Inner VLAN COS Encoding: Defines a list of {operation, value} pairs used to match 3-bit inner VLAN COS fields [802.1p] using for virtual local-area network (VLAN) stacking or Q in Q case. Values are encoded using a single byte, where the five most significant bits are zero and the three least significant bits contain the VLAN COS value. In single VLAN case, the component type MUST not be used. 4. Ethernet Flow Specification Traffic Actions +--------+--------------------+--------------------------+ | type | extended community | encoding | +--------+--------------------+--------------------------+ | 0x8006 | traffic-rate | 2-byte as#, 4-byte float | | 0x8007 | traffic-action | bitmask | | 0x8008 | redirect | 6-byte Route Target | | 0x8009 | traffic-marking | DSCP value | +--------+--------------------+--------------------------+ Besides to support the above extended communities per RFC5575, this document also proposes the following BGP extended communities specifications for Ethernet flow to extend [RFC5575]: Hao & Liang,et,al Expires November 9, 2015 [Page 6] Internet-Draft EVPN Flow Spec May 2015 +--------+------------------------+--------------------------+ | type | extended community | encoding | +--------+------------------------+--------------------------+ | 0x800A | VLAN-action | bitmask | | 0x800B | TPID-action | bitmask | +--------+------------------------+--------------------------+ VLAN-action: The VLAN-action extended community consists of 6 bytes which include the fields of action Flags, and two VLAN ID/COS value. The action Flags field includes PO, PU, SW, RI, RO, CI and CO Flag to indicate the action type. The two VLAN ID/COS value are carried in COS1/VLAN ID1 and COS2/VLAN ID2 field respectively. 0 15 +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |PO|PU|SW|RI|RO|CI|CO| Resv | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | COS1 |R | VLAN ID1 | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | COS2 |R | VLAN ID2 | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ PO: Pop action. It indicates the outmost VLAN should be removed. PU: Push action. It indicates a new VLAN should be added as outmost VLAN, the new VLAN is VLAN ID1. SW: Swap action. It indicates the outer VLAN and inner VLAN should be swapped. RI: Rewrite inner VLAN action. It indicates the inner VLAN should be replaced by a new VLAN, the new VLAN is VLAN ID1. RO: Rewrite outer VLAN action. It indicates the outer VLAN should be replaced by a new VLAN, the new VLAN is VLAN ID2. CI: Mapping inner COS action. It indicates the inner COS should be replaced by a new COS, the new COS is COS1. CO: Mapping outer COS action. It indicates the outer COS should be replaced by a new COS, the new COS is COS2. Resv: Reserved for future use. COS1: 3 bits. COS value. Hao & Liang,et,al Expires November 9, 2015 [Page 7] Internet-Draft EVPN Flow Spec May 2015 COS2: 3 bits. COS value. VLAN ID1: 12 bits. VLAN ID value. VLAN ID2: 12 bits. VLAN ID value. R: Reserved for future use. TPID-action: The TPID-action extended community consists of 6 bytes which include the fields of action Flags, TPID1 and TPID2. 0 15 +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |TI|TO| Resv | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | TP ID1 | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ | TP ID2 | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ TI: Mapping inner TP ID action. It indicates the inner TP ID should be replaced by a new TP ID, the new TP ID is TP ID1. TO: Mapping outer TP ID action. It indicates the outer TP ID should be replaced by a new TP ID, the new TP ID is TP ID2. Resv: Reserved for future use. In some cases, some more complicated actions are needed, such as SwapPop, PushSwap, etc. These actions can be represented using two catenated VLAN-actions which are carried in two VLAN-action extended communities. For example, Swap and Pop action can be represented by catenation of Swap action 1 and Pop action 2. 5. Security Considerations No new security issues are introduced to the BGP protocol by this specification. 6. IANA Considerations IANA is requested to rename currently defined SAFI 134 per [RFC5575] to read: Hao & Liang,et,al Expires November 9, 2015 [Page 8] Internet-Draft EVPN Flow Spec May 2015 134 VPN dissemination of flow specification rules IANA is requested to create and maintain a new registry for "Flow spec L2VPN Component Types". For completeness, the types defined in [RFC5575] and [draft-ietf-idr-flow-spec-v6-06] also are listed here. +--------+-------------------------------+--------------------------+ | type | RFC or Draft | discription | +--------+-------------------------------+--------------------------+ | 1 |RFC5575 | Destination Prefix | | 1 |draft-ietf-idr-flow-spec-v6-06 | Destination IPv6 Prefix | | 2 |RFC5575 | Source Prefix | | 2 |draft-ietf-idr-flow-spec-v6-06 | Source IPv6 Prefix | | 3 |RFC5575 | IP Protocol | | 3 |draft-ietf-idr-flow-spec-v6-06 | Next Header | | 4 |RFC5575 | Port | | 5 |RFC5575 | Destination port | | 6 |RFC5575 | Source port | | 7 |RFC5575 | ICMP type | | 8 |RFC5575 | ICMP code | | 9 |RFC5575 | TCP flags | | 10 |RFC5575 | Packet length | | 11 |RFC5575 | DSCP | | 12 |RFC5575 | Fragment | | 13 |draft-ietf-idr-flow-spec-v6-06 | Flow Label | | 14 |This draft | Source MAC | | 15 |This draft | Destination MAC | | 16 |This draft | Ethernet Type | | 17 |This draft | DSAP in LLC | | 18 |This draft | SSAP in LLC | | 19 |This draft | Control field in LLC | | 20 |This draft | SNAP | | 21 |This draft | VLAN ID | | 22 |This draft | VLAN COS | | 23 |This draft | Inner VLAN ID | | 24 |This draft | Inner VLAN COS | +--------+-------------------------------+--------------------------+ IANA is requested to update the reference for the following assignment in the "BGP Extended Communities Type - extended, transitive" registry: Type value Name Reference ---------- ---------------------------------------- --------- 0x080A Flow spec VLAN action [this document] Hao & Liang,et,al Expires November 9, 2015 [Page 9] Internet-Draft EVPN Flow Spec May 2015 0x080B Flow spec TPID action [this document] 6.1. Normative References [1] [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [2] [RFC5575] P. Marques, N. Sheth, R. Raszuk, B. Greene, J.Mauch, D. McPherson, "Dissemination of Flow Specification Rules", RFC 5575, August 2009. [3] [RFC4761] K. Kompella, Ed., Y. Rekhter, Ed., "Virtual Private LAN Service (VPLS) Using BGP for Auto-Discovery and Signaling", RFC4761, January 2007. [4] [RFC4762] M. Lasserre, Ed., V. Kompella, Ed., "Virtual Private LAN Service (VPLS) Using Label Distribution Protocol (LDP) Signaling", RFC4762, January 2007. [5] [RFC6074] E. Rosen, B. Davie, V. Radoaca, "Provisioning, Auto- Discovery, and Signaling in Layer 2 Virtual Private Networks (L2VPNs)", RFC6074, January 2011. 6.2. Informative References [1] [EVPN] Sajassi et al., "BGP MPLS Based Ethernet VPN", draft- ietf-l2vpn-evpn-07.txt, work in progress, May, 2014. [2] [IEEE 802.1p] Javin, et.al. "IEEE 802.1p: LAN Layer 2 QoS/CoS Protocol for Traffic Prioritization", 2012-02-15 7. Acknowledgments The authors wish to acknowledge the important contributions of Hannes Gredler, Xiaohu Xu and Lucy Yong. Hao & Liang,et,al Expires November 9, 2015 [Page 10] Internet-Draft EVPN Flow Spec May 2015 Authors' Addresses Weiguo Hao Huawei Technologies 101 Software Avenue, Nanjing 210012 China Email: haoweiguo@huawei.com Qiandeng Liang Huawei Technologies 101 Software Avenue, Nanjing 210012 China Email: liangqiandeng@huawei.com Shunwan Zhuang Huawei Technologies Huawei Bld., No.156 Beiqing Rd. Beijing 100095 China Email: zhuangshunwan@huawei.com James Uttaro AT&T EMail: uttaro@att.com Stephane Litkowski Orange stephane.litkowski@orange.com Hao & Liang,et,al Expires November 9, 2015 [Page 11]