Disman Working Group S. Chisholm Internet Draft Nortel Networks Document: draft-ietf-disman-alarm-mib-14.txt D. Romascanu Category: Standards Track Avaya Inc Expiration Date: December 2003 June 2003 Alarm MIB Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet- Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Copyright Notice Copyright (C) The Internet Society (2003). All Rights Reserved. Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes management objects used for modelling and storing alarms. Table of Contents 1. The Internet-Standard Management Framework 2. Introduction 3. Alarm Management Framework 3.1. Terminology 3.2. Alarm Management Architecture 3.3. Features of this Architecture 3.4. Security 3.5. Relationship between Alarm and Notifications Chisholm & Romascanu Standards Track [Page 1] Alarm MIB June 2003 3.6. Notification Varbind Storage and Reference 3.7. Relation to Notification Log MIB 3.8. Relation to Event MIB 4. Generic Alarm MIB 4.1. Overview 4.2. Definitions 5. ITU Alarm 5.1. Overview 5.2. IANA Considerations 5.3. Textual Conventions 5.4. Definitions 6. Examples 6.1. Alarms Based on linkUp/linkDown Notifications 6.2. Temperature Alarm using generic Notifications 6.3. Temperature Alarm without Notifications 6.4. Printer MIB Alarm Example 6.5. Rmon Alarm Example 6.6. The Lifetime of an Alarm 7. Security Considerations 8. Authors' Addresses 9. Acknowledgements 10. Intellectual Property 11. References 12. Full Copyright Statement Chisholm & Romascanu Standards Track [Page 2] Alarm MIB June 2003 1. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 2. Introduction In traditional SNMP management, problems are detected on an entity either through polling interesting MIB variables, waiting for the entity to send a Notification for a problem, or some combination of the two. This method is somewhat successful, but experience has shown some problems with this approach. Managers monitoring large number of entities cannot afford to be polling large numbers of objects on each device. Managers trying to ensure high-reliability are unable to accurately determine problems that may have occurred when they were not monitoring an entity. Finally, it can be time consuming for managers to try to understand the relationships between the various objects they poll, the Notifications they receive and the problems occurring on the entity and even after detailed analysis they may still be left with an incomplete picture of what problems are occurring. But, it is important for an operator to be able to determine current problems on a system, so they can be fixed. This memo describes a method of using alarm management in SNMP to address these problems. It also provides the necessary MIB objects to support these methods. Alarms and other terms related to alarms management are defined in the following sections. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 3. Alarm Management Framework Chisholm & Romascanu Standards Track [Page 3] Alarm MIB June 2003 3.1 Terminology Error A deviation of a system from normal operation. Fault Lasting error or warning condition. Event Something that happens which may be of interest to a management station. A fault, a change in status, crossing a threshold, or an external input to the system, for example. Notification Unsolicited transmissions of management information. Alarm Persistent indication of a fault. Alarm State A condition or stage in the existence of an alarm. As a minimum, alarms states are raise and clear. They could also include severity information such as defined by perceived severity in the ITU model - cleared, indeterminate, critical, major, minor and warning. Alarm Raise The initial detection of the fault indicated by an alarm or any number of alarm states later entered, except clear. A Notification SHOULD be sent on alarm raise. Alarm Clear The detection that the fault indicated by an alarm no longer exists. A Notification SHOULD be sent on alarm clear. Active Alarm An alarm which has an alarm state that has been raised, but not cleared. Alarm Detection Point The entity that detected the alarm. Perceived Severity The severity of the alarm as determined by the alarm detection point using the information it has available. Chisholm & Romascanu Standards Track [Page 4] Alarm MIB June 2003 3.2 Alarm Management Architecture +------------------------------------------------+ | | | +------------------------------------+ | | | Notification Management | | | +--------------+---------------------+ | | | | +------------------+-----------------------------+ | V | |<----------------------------------------------+ | | +------------------V-------------+ | | +---------------V-----------+ | | | | RFC 3413 | | | | | SNMP-NOTIFICATION-MIB | | | | +--------+--------------+-+-+ | | | | | | | | | | | +------------------+ | | | | | | | | | | | +----------V--------------+ | | | | | | +--------V---------+ | | | +---------V------------+ | | | | Alarm Modelling | | | | | RFC 3014 | | | | | (descriptions) | | | | | NOTIFICATION-LOG-MIB | | | | +--------+---------+ | | | +----------------------+ | | | | | | | | | | +--------V------------+ | | | +------------------------V-+ | | | Generic: Model- | | | | | RFC 3413 | | | | Active : Specific | | | | | SNMP-TARGET-MIB | | | | Alarms : Extensions | | | | +----------+---------------+ | | +--------+------------+ | | | | | | | | | +------------|-------------------+ +----------|--------------+ | | | | | +------------------+ V Informs & Traps 3.3 Features of this Architecture 3.3.1 Modular Alarm Architecture The subject of alarm management can potentially cover a large number of topics including real-time alarms, historical alarms, alarm correlation, and alarm suppression, to name a few. Within each of these topics, there are a number of established models that could be supported. This memo focuses on a subset of this problem space, but describes a modular SNMP alarm management framework. Chisholm & Romascanu Standards Track [Page 5] Alarm MIB June 2003 The framework defines a generic Alarm MIB that can be supported on its own, or with additional alarm modelling information such as the provided ITU Alarm MIB. In addition, the active alarm tables could also be extended to support additional information about active alarm instances. This framework can also be expanded in the future to support such features as alarm correlation and alarm suppression. This modular architecture means that the cost of supporting alarm management features is proportional to the number of features an implementation supports. 3.3.2 Flexible Alarm Modelling Alarm models document an understanding between a manager and an agent as to what problems will be reported on a system, how these problems will be reported, and what might possibly happen over the lifetime of this problem. The alarm modelling method provided in this memo provides flexibility to support implementations with different modelling requirements. All alarms are modelled as a series of states that are related together using an alarm ID. Alarm states can be modelled using traditional Notifications, generic alarm Notifications, or without the use of Notifications. Alarm states modelled using traditional Notifications would identify a Notification OID, and optionally an offset, value pair of one of the Notification varbinds to define the state. This alarm state would be entered when the entity generated a Notification that matched this information and the alarm would be added to the active alarm table. This Notification would also get sent on the wire to any destinations, as indicated in the SNMP-TARGET-MIB [RFC3413]. Alarm states modelled using generic Notifications, use the alarmActiveState or alarmClearState Notifications defined in this memo. These alarm states would be entered by some internal stimuli, the alarm would be added to the active alarm table and these generic Notifications would then be sent on the wire to any destinations, as indicated in the SNMP-TARGET-MIB [RFC3413]. Alarm states modelled without any Notifications would be triggered by some internal stimuli, the alarm would be added to the active alarm table, but no Notifications would be sent to interested managers. 3.3.3 Problem Indication The Alarm MIB provides a means to tell what Notifications are just informational events or not of interest to the manager for other reasons by not including them in any alarm models. In addition, information in the alarm model, such as the Notification ID and the description tell exactly what error or warning condition this alarm is indicating. If the ITU-ALARM-MIB is also supported, additional Chisholm & Romascanu Standards Track [Page 6] Alarm MIB June 2003 information is provided via the probable cause. 3.3.5 Identifying Resource under Alarm An important goal of alarm management is to ensure that any detected problems get fixed, so it is necessary to know exactly where this problem is occurring. In addition, it is necessary to be able to tell when alarm instances are raised against the same component, as well as to be able to tell what instance of an alarm is cleared by an instance of an alarm clear. The Alarm MIB provides a generic method for identifying the resource by extracting and building a resource ID from the Notification varbinds. Solutions interested in being able to differentiate the source of the alarm by means other than the source IP address and resource ID should create separate alarm lists such that each context/source IP address pair is its own list. 3.3.6 Means of obtaining ITU alarm information Alarm Information, as defined in ITU alarm models [M.3100], is optionally available to implementations through the optional support of the ITU-ALARM-MIB. 3.3.7 Configuration of Alarm Models An alarm model can be added, updated or removed during runtime, assuming it is not being referenced by any active alarm instance. 3.3.8 Active Alarm Management A list of currently active alarms on a system and supporting statistics on the SNMP entity can be obtained. This allows the network management station to find out about any problems that may have occurred before it started managing a particular network element, or while it was out of contact with it. 3.3.9 Distributed Alarm Management All aspects of the Alarm MIB can be supported both on the device experiencing the alarms and on any middle managers that might be monitoring such devices. 3.3.10 Historical Alarm Management Some systems may have a requirement that information on alarms that are no longer active is available. This memo provides a clear table to support this requirement. This can also be achieved through the support of the Notification log MIB [RFC3014] to store alarm state transitions. Chisholm & Romascanu Standards Track [Page 7] Alarm MIB June 2003 3.4 Security Security for alarms is awkward since access control for the objects in the underlying Notifications can be checked only where the Notification is created. Thus such checking is possible only for locally generated Notifications, and even then only when security credentials are available. For the purpose of this discussion, "security credentials" means the input values for the abstract service interface function isAccessAllowed [RFC3411] and using those credentials means conceptually using that function to see that those credentials allow access to the MIB objects in question, operating as for a Notification Originator in [RFC3413]. The Alarm MIB has the notion of a named alarm list. By using alarm list names and view-based access control [RFC3415] a network administrator can provide different access for different users. When an application creates an alarm model (indexed in part by the alarm list name) the security credentials of the creator remain associated with that alarm model and constrain what information is allowed to be placed in the active alarm table, the active alarm variable table, the cleared alarm table, and the ITU alarm table. When processing locally-generated Notifications, the managed system MUST use the security credentials associated with each alarm model respectively, and MUST apply the same access control rules as described for a Notification Originator in [RFC3413]. The managed system SHOULD NOT apply access control when processing remotely-generated Notifications using the alarm models. In those cases the security of the information in the alarm tables SHOULD be left to the normal, overall access control for those tables. 3.5 Relationship between Alarm and Notifications It is important to understand the relationship between alarms and Notifications, as both are traditional fault management methods. This relationship is modelled using the alarmModelTable to define the alarmModelNotificationId for each alarm state. Not all Notifications signal an alarm state transition. Some Notifications are simply informational in nature, such as those that indicate that a configuration operation has been performed on an entity. These sorts of Notifications would not be represented in the Alarm MIB. The Alarm MIB allows the use of the Notification space as defined in [RFC2578] in order to identify the Notifications that are related with the specific alarm state transitions. However there is no Chisholm & Romascanu Standards Track [Page 8] Alarm MIB June 2003 assumption that the respective Notifications MUST be sent for all or any of the alarm state transitions. It is also possible to model alarms using no Notifications at all. This architecture allows for both the efficient exploitation of the body of defined Notification and for the use of non-Notification based systems. 3.6 Notification Varbind Storage and Reference In SNMPv1 [RFC1157], the varbinds in the Trap-PDU sent over the wire map one to one into those varbinds listed in the SMI of the trap in the MIB in which it was defined[RFC1215]. In the case of linkDown trap, the first varbind can unambiguously be identified as ifIndex. With the introduction of the InformRequest-PDU and SNMPv2-Trap-PDU types, which send sysUptime and snmpTrapOID as the first two varbinds, while the SMI in the MIB where the Notification is defined only lists additional varbinds, the meaning of "first varbind" becomes less clear. In the case of the linkDown Notification, referring to the first varbind could potentially be interpreted as either the sysUptime or ifIndex. The varbind storage approach taken in the Alarm MIB is that sysUptime and snmpTrapOID SHALL always be stored in the active alarm variable table as entry 1 and 2 respectively, regardless of whether the transport was the Trap-PDU, the InformRequest-PDU or the SNMPv2-Trap-PDU. If the incoming Notification is an SNMPv1 Trap-PDU then an appropriate value for sysUpTime.0 or snmpTrapOID.0 shall be determined by using the rules in section 3.1 of [RFC2576]. The varbind reference approach taken in the Alarm MIB is that, for variables such as the alarmModelVarbindIndex, the first two obligatory varbinds of the InformRequest-PDU and SNMPv2-Trap-PDU are ignored, and the index aligns with the Trap-PDU and the SMI. In the case of linkDown, the first varbind would always be ifIndex. 3.7 Relation to Notification Log MIB The Alarm MIB is intended to complement the Notification Log MIB[RFC3014], but can be used independently. The alarmActiveTable is defined in manner similar to that of the nlmLogTable. This format allows for the storage of any Trap or Notification that can be defined using SMIv1 or SMIv2. Using the same format as the Notification log MIB also simplifies operations for systems choosing to implement both MIBs. The object alarmActiveLogPointer points, for each entry in the alarmActiveLogTable, to the log index in the Notification log MIB, if used. If the Notification log MIB is supported, it can be monitored by a management system as a hedge against lost alarms. The Notification log can also be used to support historical alarm management. Chisholm & Romascanu Standards Track [Page 9] Alarm MIB June 2003 3.8 Relationship with the Event MIB During the work and discussions in the Working Group, the issue of the relationship between the MIB modules and the Event MIB [RFC2981] was raised. There is no direct relation or dependency between the Alarm MIB and the Event MIB. Some common terms (like 'event') are being used in both MIB modules, and the user is directed to the sections that define terminology in the two documents for clarification. 4. Generic Alarm MIB 4.1 Overview The ALARM-MIB consists of alarm models and lists of active and cleared alarms. The alarmModelTable contains information that is applicable to all instances of an alarm. It can be populated at start-up with all alarms that could happen on a system or later configured by a management application. It contains all the alarms for a given system. If a Notification is not represented in the alarmModelTable, it is not an alarm state transition. The alarmModelTable provides a means of defining the raise/clear and other state transition relationship between alarm states. alarmModelIndex acts as a unique identifier for an alarm. An alarm model consists of defining the possible states an alarm can assume as well as the OID of the Notification that is sent out when an alarm changes state. The object alarmModelState defines the states of an alarm. The alarmActiveTable contains a list of alarms that are currently occurring on a system. It is intended that this table be queried upon device discovery and rediscovery to determine which alarms are currently active on the device. The alarmActiveVariableTable contains the Notification variable bindings associated with the alarms in the alarmActiveTable. The alarmActiveStatsTable contains current and total raised alarm counts as well as the time of the last alarm raise and alarm clears per named alarm list. The alarmClearTable contains recently cleared alarms. It contains up to alarmClearMaximum cleared alarms. The MIB also defines generic alarm Notifications that can be used when there is not an existing applicable Notification to signal the alarm state transition - alarmActiveState and alarmClearState. Chisholm & Romascanu Standards Track [Page 10] Alarm MIB June 2003 4.1.1 Extensibility The relationship between the Alarm MIB and the other alarm model MIB modules is expressed by the following: The alarmModelTable has a corresponding table in the specific MIB. For each row in the specific MIB alarm model table there is one row in the alarmModelTable. The alarmActiveTable has a corresponding table in the specific MIBs. For each row in the specific MIB active alarm table, there is one row in the alarmActiveTable. The alarmModelSpecificPointer object in the alarmModelTable points to the specific model entry in an extended alarm model table corresponding to this particular alarm. The alarmActiveSpecificPointer object in the alarmActiveTable points to the specific active alarm entry in an extended active alarm table corresponding to this particular alarm instance. 4.1.2 Problem Indication The problem that each alarm indicates is identified through the OID of the NotificationId of the state transition, and, optionally, the ITU parameters. alarmModelDescription provides a description of the alarm state suitable for displaying to an operator. 4.1.3 Alarm State Transition Notification Managers interested in receiving a Notification when an alarm changes state can associate a Notification with an alarm state change. Alarm state transitions can use existing Notifications or can use the generic Notifications and alarmActiveState and alarmClearState. If the implementation chooses not to alert the management station, then a value of 0.0 can be used for alarmModelNotificationId. Alternatively, a Notification can be defined in alarmModelNotificationId and no hosts specified in the SNMP-TARGET-MIB [RFC3413]. Alarms are modelled by defining all possible states in the alarmModelTable, as well as defining alarmModelNotificationId, alarmModelVarbindIndex, and alarmModelVarbindValue for each of the possible alarm states. Optionally, ituAlarmPerceivedSeverity models the states in terms of ITU perceived severity. 4.1.4 Active Alarm Resource Identifier Resources under alarm can be identified using the alarmActiveResourceId. This OBJECT IDENTIFIER points to an appropriate object to identify the given resource, depending on the type of the resource. The consumer of the alarmActiveResourceId does not necessarily need to know the type of the resource in the resource ID, but if they want to know this, examining the content of the resource ID can derive it - 1.3.6.1.2.1.2.2.1.1.something is an interface for Chisholm & Romascanu Standards Track [Page 11] Alarm MIB June 2003 example. It is therefore good practice to use resource IDs that can be consistently used across technologies such as ifIndex, entPhysicalIndex or sysApplRunIndex to minimize the number of resource prefixes a manager interested in resource type needs to learn. Resource ID can be calculated using the alarmModelResourcePrefix, alarmModelVarbindSubtree and the Notification varbinds. This allows for both the managed element to be able to compute and populate the alarmActiveResourceId object and for the manager to be able to determine when two separate alarm instances are referring to the same resource. If alarmModelResourcePrefix has a value of 0.0, then alarmActiveResourceId is simply the variable identifier of the first Notification varbind that matches the prefix defined in alarmModelVarbindSubtree. Otherwise, alarmActiveResourceId is calculated by appending the instance information from the first Notification varbind that matches alarmModelVarbindSubtree to the prefix defined in alarmModelResourcePrefix. The instance information is the portion of the variable identifier following the part that matched alarmModelVarbindSubtree. If no match is found, then alarmActiveResourceId is simply the value of alarmModelResourcePrefix. In addition to this, the variable bindings from the Notifications that signal the alarm state transitions are stored in the active alarm variable table. This allows for implementations familiar with the particular Notifications to implement other forms of resource identification. For Example: A) Consider an alarm modelled using the authenticationFailure Notification. authenticationFailure NOTIFICATION-TYPE STATUS current DESCRIPTION "An authenticationFailure trap signifies that the SNMPv2 entity, acting in an agent role, has received a protocol message that is not properly authenticated. While all implementations of the SNMPv2 must be capable of generating this trap, the snmpEnableAuthenTraps object indicates whether this trap will be generated." ::= { snmpTraps 5 } To set the resource ID to be usmStats, 1.3.6.1.6.3.15.1.1, configure as follows: alarmModelVarbindSubtree = 0.0 alarmModelResourcePrefix = usmStats (1.3.6.1.6.3.15.1.1) Chisholm & Romascanu Standards Track [Page 12] Alarm MIB June 2003 B) Consider an alarm modelled using linkDown linkDown NOTIFICATION-TYPE OBJECTS { ifIndex, ifAdminStatus, ifOperStatus } STATUS current DESCRIPTION "" ::= { snmpTraps 3 } To set the resource Id to be the ifIndex, configure as follows: alarmModelVarbindSubtree = ifIndex (1.3.6.1.2.1.2.2.1.1) alarmModelResourcePrefix = 0.0 Alternatively, since ifIndex is the first varbind, the following would also work, but might be less meaningful to a human reader of the MIB table: alarmModelVarbindSubtree = 0.0 alarmModelResourcePrefix = 0.0 C) Consider an alarm modelled using the bgpBackwardTransition Notification. bgpBackwardTransition NOTIFICATION-TYPE OBJECTS { bgpPeerLastError, bgpPeerState } STATUS current DESCRIPTION "The BGPBackwardTransition Event is generated when the BGP FSM moves from a higher numbered state to a lower numbered state." ::= { bgpTraps 2 } To set the resource Id to be the bgpPeerRemoteAddr, the index to the bgpTable, where bgpPeerState resides, configure as follows: alarmModelVarbindSubtree = bgpPeerState (1.3.6.1.2.1.15.3.1.2) alarmModelResourcePrefix = bgpPeerRemoteAddr (1.3.6.1.2.1.15.3.1.7) 4.1.5 Configurable Alarm Models The alarm model table can, and probably should, be initially populated by the system. The objects in alarmModelTable and ituAlarmTable have a MAX-ACCESS of read-write, which allows the manager to modify the alarm models to suit their requirements. 4.1.6 Active Alarm Management Lists of alarms currently active on an SNMP entity are stored in the alarmActiveTable and, optionally a model specific alarmTable, e.g. the ituAlarmActiveTable. Chisholm & Romascanu Standards Track [Page 13] Alarm MIB June 2003 4.1.7 Distributed Alarm Management Distributed alarm management can be achieved by support of the Alarm MIB on both the alarm detection point and on the mid-level manager. This is facilitated by the ability to be able to store different named alarm lists. A middle manager could therefore, create an alarmListName for each of the devices it manages and therefore store separate lists for each device. In additional, the context and IP addresses of the alarm detection point are stored in the alarmActiveTable. 4.2 Definitions ALARM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Unsigned32, Gauge32, TimeTicks, Counter32, Counter64, IpAddress, Opaque, mib-2 FROM SNMPv2-SMI DateAndTime, RowStatus, RowPointer, TEXTUAL-CONVENTION FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; alarmMIB MODULE-IDENTITY LAST-UPDATED "200306090000Z" ORGANIZATION "IETF Distributed Management Working Group" CONTACT-INFO "WG EMail: disman@ietf.org Subscribe: disman-request@ietf.org http://www.ietf.org/html.charters/disman-charter.html Chair: Randy Presuhn randy_presuhn@mindspring.com Editors: Sharon Chisholm Nortel Networks PO Box 3511 Station C Ottawa, Ont. K1Y 4H7 Canada schishol@nortelnetworks.com Dan Romascanu Avaya Inc. Atidim Technology Park, Bldg. #3 Tel Aviv, 61131 Israel Tel: +972-3-645-8414 Chisholm & Romascanu Standards Track [Page 14] Alarm MIB June 2003 Email: dromasca@avaya.com" DESCRIPTION "The MIB module describes a generic solution to model alarms and to store the current list of active alarms. Copyright (C) The Internet Society (2003). The initial version of this MIB module was published in RFC xxxx. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html" -- RFC Ed.: replace yyyy with actual RFC number & remove -- this note REVISION "200306090000Z" DESCRIPTION "Initial version, published as RFC yyyy." -- RFC-Editor assigns yyyy ::= { mib-2 XX } -- to be assigned by IANA alarmObjects OBJECT IDENTIFIER ::= { alarmMIB 1 } alarmNotifications OBJECT IDENTIFIER ::= { alarmMIB 0 } alarmModel OBJECT IDENTIFIER ::= { alarmObjects 1 } alarmActive OBJECT IDENTIFIER ::= { alarmObjects 2 } alarmClear OBJECT IDENTIFIER ::= { alarmObjects 3 } -- Textual Conventions -- ResourceId is intended to be a general textual convention -- that can be used outside of the set of MIBs related to -- Alarm Management. ResourceId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "A unique identifier for this resource. The type of the resource can be determined by looking at the OID that describes the resource. Resources must be identified in a consistent manner. For example, if this resource is an interface, this object MUST point to an ifIndex." SYNTAX OBJECT IDENTIFIER LocalSnmpEngineOrZeroLenStr ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An SNMP Engine ID or a zero length string. The Chisholm & Romascanu Standards Track [Page 15] Alarm MIB June 2003 instantiation of this object will provide guidance on when this will be an SNMP Engine ID and when it will be a zero lengths string" SYNTAX OCTET STRING (SIZE(0 | 5..32)) -- Alarm Model alarmModelLastChanged OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last creation, deletion or modification of an entry in the alarmModelTable. If the number and content of entries has been unchanged since the last re-initialization of the local network management subsystem, then the value of this object MUST be zero." ::= { alarmModel 1 } alarmModelTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmModelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of information about possible alarms on the system, and how they have been modelled." ::= { alarmModel 2 } alarmModelEntry OBJECT-TYPE SYNTAX AlarmModelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries appear in this table for each possible alarm state. This table MUST be persistent across system reboots." INDEX { alarmListName, alarmModelIndex, alarmModelState } ::= { alarmModelTable 1 } AlarmModelEntry ::= SEQUENCE { alarmModelIndex Unsigned32, alarmModelState Unsigned32, alarmModelNotificationId OBJECT IDENTIFIER, alarmModelVarbindIndex Unsigned32, alarmModelVarbindValue Integer32, alarmModelDescription SnmpAdminString, alarmModelSpecificPointer RowPointer, alarmModelVarbindSubtree OBJECT IDENTIFIER, alarmModelResourcePrefix OBJECT IDENTIFIER, alarmModelRowStatus RowStatus Chisholm & Romascanu Standards Track [Page 16] Alarm MIB June 2003 } alarmModelIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer that acts as an alarm Id to uniquely identify each alarm within the named alarm list. " ::= { alarmModelEntry 1 } alarmModelState OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A value of 1 MUST indicate a clear alarm state. The value of this object MUST be less than the alarmModelState of more severe alarm states for this alarm. The value of this object MUST be more than the alarmModelState of less severe alarm states for this alarm." ::= { alarmModelEntry 2 } alarmModelNotificationId OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The NOTIFICATION-TYPE object identifier of this alarm state transition. If there is no notification associated with this alarm state, the value of this object MUST be '0.0'" ::= { alarmModelEntry 3 } alarmModelVarbindIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The index into the varbind listing of the notification indicated by alarmModelNotificationId which helps signal that the given alarm has changed state. If there is no applicable varbind, the value of this object MUST be zero. Note that the value of alarmModelVarbindIndex ignores the existence of the first two obligatory varbinds in the InformRequest-PDU and SNMPv2-Trap-PDU (sysUpTime.0 and snmpTrapOID.0). That is, a value of 1 refers to Chisholm & Romascanu Standards Track [Page 17] Alarm MIB June 2003 the first varbind after snmpTrapOID.0. If the incoming notification is instead an SNMPv1 Trap-PDU, then a value of 1 refers to the first varbind." ::= { alarmModelEntry 4 } alarmModelVarbindValue OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The value that the varbind indicated by alarmModelVarbindIndex takes to indicate that the alarm has entered this state. " ::= { alarmModelEntry 5 } alarmModelDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "A brief description of this alarm and state suitable to display to operators." ::= { alarmModelEntry 6 } alarmModelSpecificPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-create STATUS current DESCRIPTION "If no additional, model-specific Alarm MIB is supported by the system the value of this object is `0.0'. When a model-specific Alarm MIB is supported, this object is the instance pointer to the model-specific alarm definition." ::= { alarmModelEntry 7 } alarmModelVarbindSubtree OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The name portion of each VarBind in the notification, in order, is compared to the value of this object. If the name is equal to or a subtree of the value of this object, for purposes of computing the value of AlarmActiveResourceID the 'prefix' will be the matching portion, and the 'indexes' will be any remainder. The examination of varbinds ends with the first match. If the value of this object is 0.0, then the first varbind, or in the case of v2, the first varbind after the timestamp and the trap Chisholm & Romascanu Standards Track [Page 18] Alarm MIB June 2003 OID, will always be matched. " ::= { alarmModelEntry 8 } alarmModelResourcePrefix OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The value of AlarmActiveResourceID is computed by appending any indexes extracted in accordance with the description of alarmModelVarbindSubtree onto the value of this object. If this object's value is 0.0, then the 'prefix' extracted is used instead. " ::= { alarmModelEntry 9 } alarmModelRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Control for creating and deleting entries. Entries may be modified while active. Alarms whose alarmModelRowStatus is not active will not appear in either the alarmActiveTable or the alarmClearTable. Setting this object to notInService cannot be used as an alarm suppression mechanism. Entries that are notInService will disappear as described in RFC2579 This row can not be modified or deleted while it is being referenced by a value of alarmActiveModelPointer. In these cases, an error of `inconsistentValue' will be returned to the manager." ::= { alarmModelEntry 10 } -- Active Alarm Table -- alarmActiveLastChanged OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last creation or deletion of an entry in the alarmActiveTable. If the number of entries has been unchanged since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { alarmActive 1 } Chisholm & Romascanu Standards Track [Page 19] Alarm MIB June 2003 alarmActiveTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Active Alarms entries." ::= { alarmActive 2 } alarmActiveEntry OBJECT-TYPE SYNTAX AlarmActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries appear in this table when alarms are raised. They are removed when the alarm is cleared." INDEX { alarmListName, alarmActiveDateAndTime, alarmActiveIndex } ::= { alarmActiveTable 1 } AlarmActiveEntry ::= SEQUENCE { alarmListName SnmpAdminString, alarmActiveDateAndTime DateAndTime, alarmActiveIndex Unsigned32, alarmActiveEngineID LocalSnmpEngineOrZeroLenStr, alarmActiveEngineAddressType InetAddressType, alarmActiveEngineAddress InetAddress, alarmActiveContextName SnmpAdminString, alarmActiveVariables Unsigned32, alarmActiveNotificationID OBJECT IDENTIFIER, alarmActiveResourceId ResourceId, alarmActiveDescription SnmpAdminString, alarmActiveLogPointer RowPointer, alarmActiveModelPointer RowPointer, alarmActiveSpecificPointer RowPointer } alarmListName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the list of alarms. This SHOULD be the same as nlmLogName if the Notification Log MIB [RFC3014] is supported. An implementation may allow multiple named alarm lists, up to some implementation-specific limit (which may be none). A zero-length list name is reserved for creation and deletion by the managed system, and MUST be used as the default log name by systems that do not support named alarm lists." ::= { alarmActiveEntry 1 } alarmActiveDateAndTime OBJECT-TYPE Chisholm & Romascanu Standards Track [Page 20] Alarm MIB June 2003 SYNTAX DateAndTime MAX-ACCESS not-accessible STATUS current DESCRIPTION "The local date and time when the error occurred. This object facilitates retrieving all instances of alarms that have been raised or have changed severity since a given point in time. Implementations MUST include the offset from UTC, if available. Implementation in environments in which the UTC offset is not available is NOT RECOMMENDED." ::= { alarmActiveEntry 2 } alarmActiveIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A strictly monotonically increasing integer which acts as the index of entries within the named alarm list. It wraps back to 1 after it reaches its maximum value." ::= { alarmActiveEntry 3 } alarmActiveEngineID OBJECT-TYPE SYNTAX LocalSnmpEngineOrZeroLenStr MAX-ACCESS read-only STATUS current DESCRIPTION "The identification of the SNMP engine at which the alarm originated. If the alarm list can contain alarms from only one engine or the alarm is from an SNMPv1 system, this object is a zero length string." ::= { alarmActiveEntry 4 } alarmActiveEngineAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates what type of address is stored in the alarmActiveEngineAddress object - IPv4, IPv6, DNS, etc." ::= { alarmActiveEntry 5 } alarmActiveEngineAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current Chisholm & Romascanu Standards Track [Page 21] Alarm MIB June 2003 DESCRIPTION "The IP Address of the SNMP engine on which the alarm is occurring. This is used to identify the source of an SNMPv1 trap, since an alarmActiveEngineId cannot be extracted from the SNMPv1 trap PDU. This object MUST always be instantiated, even if the list can contain alarms from only one engine." ::= { alarmActiveEntry 6 } alarmActiveContextName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the SNMP MIB context from which the alarm came. For SNMPv1 alarms this is the community string from the Trap. If the alarm's source SNMP engine is known not to support multiple contexts, this object is a zero length string." ::= { alarmActiveEntry 7 } alarmActiveVariables OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of variables in alarmActiveVariableTable for this alarm." ::= { alarmActiveEntry 8 } alarmActiveNotificationID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The NOTIFICATION-TYPE object identifier of the alarm state transition that is occurring." ::= { alarmActiveEntry 9 } alarmActiveResourceId OBJECT-TYPE SYNTAX ResourceId MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the resource under alarm. If there is no corresponding resource, then the value of this object MUST be 0.0." ::= { alarmActiveEntry 10 } alarmActiveDescription OBJECT-TYPE Chisholm & Romascanu Standards Track [Page 22] Alarm MIB June 2003 SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides a textual description of the active alarm. This text is generated dynamically by the notification generator to provide useful information to the human operator. This information SHOULD provide information allowing the operator to locate the resource for which this alarm is being generated. This information is not intended for consumption by automated tools." ::= { alarmActiveEntry 11 } alarmActiveLogPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the corresponding row in a notification logging MIB where the state change notification for this active alarm is logged. If no log entry applies to this active alarm, then this object MUST have the value of 0.0" ::= { alarmActiveEntry 12 } alarmActiveModelPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the corresponding row in the alarmModelTable for this active alarm. This points not only to the alarm model being instantiated, but also to the specific alarm state that is active." ::= { alarmActiveEntry 13 } alarmActiveSpecificPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "If no additional, model-specific, Alarm MIB is supported by the system this object is `0.0'. When a model-specific Alarm MIB is supported, this object is the instance pointer to the specific model-specific active alarm list." ::= { alarmActiveEntry 14 } -- Active Alarm Variable Table -- Chisholm & Romascanu Standards Track [Page 23] Alarm MIB June 2003 alarmActiveVariableTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmActiveVariableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of variables to go with active alarm entries." ::= { alarmActive 3 } alarmActiveVariableEntry OBJECT-TYPE SYNTAX AlarmActiveVariableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries appear in this table when there are variables in the varbind list of a corresponding alarm in alarmActiveTable. Entries appear in this table as though the trap/notification had been transported using a SNMPv2-Trap-PDU, as defined in [RFC3416] - i.e, the alarmActiveVariableIndex 1 will always be sysUpTime and alarmActiveVariableIndex 2 will always be snmpTrapOID. If the incoming notification is instead an SNMPv1 Trap-PDU and the value of alarmModelVarbindIndex is 1 or 2, an appropriate value for sysUpTime.0 or snmpTrapOID.0 shall be determined by using the rules in section 3.1 of [RFC2576]." INDEX { alarmListName, alarmActiveIndex, alarmActiveVariableIndex } ::= { alarmActiveVariableTable 1 } AlarmActiveVariableEntry ::= SEQUENCE { alarmActiveVariableIndex Unsigned32, alarmActiveVariableID OBJECT IDENTIFIER, alarmActiveVariableValueType INTEGER, alarmActiveVariableCounter32Val Counter32, alarmActiveVariableUnsigned32Val Unsigned32, alarmActiveVariableTimeTicksVal TimeTicks, alarmActiveVariableInteger32Val Integer32, alarmActiveVariableOctetStringVal OCTET STRING, alarmActiveVariableIpAddressVal IpAddress, alarmActiveVariableOidVal OBJECT IDENTIFIER, alarmActiveVariableCounter64Val Counter64, alarmActiveVariableOpaqueVal Opaque } alarmActiveVariableIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION Chisholm & Romascanu Standards Track [Page 24] Alarm MIB June 2003 "A strictly monotonically increasing integer, starting at 1 for a given alarmActiveIndex, for indexing variables within the active alarm list. " ::= { alarmActiveVariableEntry 1 } alarmActiveVariableID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The alarm variable's object identifier." ::= { alarmActiveVariableEntry 2 } alarmActiveVariableValueType OBJECT-TYPE SYNTAX INTEGER { counter32(1), unsigned32(2), timeTicks(3), integer32(4), ipAddress(5), octetString(6), objectId(7), counter64(8), opaque(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the value. One and only one of the value objects that follow is used, based on this type." ::= { alarmActiveVariableEntry 3 } alarmActiveVariableCounter32Val OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'counter32'." ::= { alarmActiveVariableEntry 4 } alarmActiveVariableUnsigned32Val OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'unsigned32'." ::= { alarmActiveVariableEntry 5 } alarmActiveVariableTimeTicksVal OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current Chisholm & Romascanu Standards Track [Page 25] Alarm MIB June 2003 DESCRIPTION "The value when alarmActiveVariableType is 'timeTicks'." ::= { alarmActiveVariableEntry 6 } alarmActiveVariableInteger32Val OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'integer32'." ::= { alarmActiveVariableEntry 7 } alarmActiveVariableOctetStringVal OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'octetString'." ::= { alarmActiveVariableEntry 8 } alarmActiveVariableIpAddressVal OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'ipAddress'." ::= { alarmActiveVariableEntry 9 } alarmActiveVariableOidVal OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'objectId'." ::= { alarmActiveVariableEntry 10 } alarmActiveVariableCounter64Val OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'counter64'." ::= { alarmActiveVariableEntry 11 } alarmActiveVariableOpaqueVal OBJECT-TYPE SYNTAX Opaque (SIZE(0..65535)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value when alarmActiveVariableType is 'opaque'." ::= { alarmActiveVariableEntry 12 } Chisholm & Romascanu Standards Track [Page 26] Alarm MIB June 2003 -- Statistics -- alarmActiveStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmActiveStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the alarm statistics information." ::= { alarmActive 4 } alarmActiveStatsEntry OBJECT-TYPE SYNTAX AlarmActiveStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics on the current active alarms." INDEX { alarmListName } ::= { alarmActiveStatsTable 1 } AlarmActiveStatsEntry ::= SEQUENCE { alarmActiveStatsActiveCurrent Gauge32, alarmActiveStatsActives Counter32, alarmActiveStatsLastRaise TimeTicks, alarmActiveStatsLastClear TimeTicks } alarmActiveStatsActiveCurrent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of currently active alarms on the system." ::= { alarmActiveStatsEntry 1 } alarmActiveStatsActives OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of active alarms since system restarted." ::= { alarmActiveStatsEntry 2 } alarmActiveStatsLastRaise OBJECT-TYPE Chisholm & Romascanu Standards Track [Page 27] Alarm MIB June 2003 SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last alarm raise for this alarm list. If no alarm raises have occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { alarmActiveStatsEntry 3 } alarmActiveStatsLastClear OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at the time of the last alarm clear for this alarm list. If no alarm clears have occurred since the last re-initialization of the local network management subsystem, then this object contains a zero value." ::= { alarmActiveStatsEntry 4 } -- Alarm Clear alarmClearMaximum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the maximum number of cleared alarms to store in the alarmClearTable. When this number is reached, the cleared alarms with the earliest clear time will be removed from the table." ::= { alarmClear 1 } alarmClearTable OBJECT-TYPE SYNTAX SEQUENCE OF AlarmClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on cleared alarms." ::= { alarmClear 2 } alarmClearEntry OBJECT-TYPE SYNTAX AlarmClearEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information on a cleared alarm." Chisholm & Romascanu Standards Track [Page 28] Alarm MIB June 2003 INDEX { alarmListName, alarmClearDateAndTime, alarmClearIndex } ::= { alarmClearTable 1 } AlarmClearEntry ::= SEQUENCE { alarmClearIndex Unsigned32, alarmClearDateAndTime DateAndTime, alarmClearEngineID LocalSnmpEngineOrZeroLenStr, alarmClearEngineAddressType InetAddressType, alarmClearEngineAddress InetAddress, alarmClearContextName SnmpAdminString, alarmClearNotificationID OBJECT IDENTIFIER, alarmClearResourceId ResourceId, alarmClearLogIndex Unsigned32, alarmClearModelPointer RowPointer } alarmClearIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An integer which acts as the index of entries within the named alarm list. It wraps back to 1 after it reaches its maximum value. This object has the same value as the alarmActiveIndex that this alarm instance had when it was active." ::= { alarmClearEntry 1 } alarmClearDateAndTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS not-accessible STATUS current DESCRIPTION "The local date and time when the alarm cleared. This object facilitates retrieving all instances of alarms that have been cleared since a given point in time. Implementations MUST include the offset from UTC, if available. Implementation in environments in which the UTC offset is not available is NOT RECOMMENDED." ::= { alarmClearEntry 2 } alarmClearEngineID OBJECT-TYPE SYNTAX LocalSnmpEngineOrZeroLenStr MAX-ACCESS read-only Chisholm & Romascanu Standards Track [Page 29] Alarm MIB June 2003 STATUS current DESCRIPTION "The identification of the SNMP engine at which the alarm originated. If the alarm list can contain Notifications from only one engine or the trap is from an SNMPv1 system, this object is a zero length string." ::= { alarmClearEntry 3 } alarmClearEngineAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates what type of address is stored in the alarmActiveEngineAddress object - IPv4, IPv6, DNS, etc." ::= { alarmClearEntry 4 } alarmClearEngineAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the SNMP engine on which the alarm was occurring. This is used to identify the source of an SNMPv1 trap, since an alarmActiveEngineId cannot be extracted from the SNMPv1 trap PDU. This object MUST always be instantiated, even if the list can contain alarms from only one engine." ::= { alarmClearEntry 5 } alarmClearContextName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the SNMP MIB context from which the alarm came. For SNMPv1 traps this is the community string from the Trap. If the alarm's source SNMP engine is known not to support multiple contexts, this object is a zero length string." ::= { alarmClearEntry 6 } alarmClearNotificationID OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "The NOTIFICATION-TYPE object identifier of the alarm clear." ::= { alarmClearEntry 7 } Chisholm & Romascanu Standards Track [Page 30] Alarm MIB June 2003 alarmClearResourceId OBJECT-TYPE SYNTAX ResourceId MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the resource that was under alarm. If there is no corresponding resource, then the value of this object MUST be 0.0." ::= { alarmClearEntry 8 } alarmClearLogIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This number MUST be the same as the log index of the applicable row in the notification log MIB, if it exists. If no log index applies to the trap, then this object MUST have the value of 0." ::= { alarmClearEntry 9 } alarmClearModelPointer OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "A pointer to the corresponding row in the alarmModelTable for this cleared alarm." ::= { alarmClearEntry 10 } -- Notifications alarmActiveState NOTIFICATION-TYPE OBJECTS { alarmActiveModelPointer, alarmActiveResourceId } STATUS current DESCRIPTION "An instance of the alarm indicated by alarmActiveModelPointer has been raised against the entity indicated by alarmActiveResourceId." ::= { alarmNotifications 2 } alarmClearState NOTIFICATION-TYPE OBJECTS { alarmActiveModelPointer, alarmActiveResourceId } STATUS current DESCRIPTION "An instance of the alarm indicated by alarmActiveModelPointer has been cleared against Chisholm & Romascanu Standards Track [Page 31] Alarm MIB June 2003 the entity indicated by alarmActiveResourceId." ::= { alarmNotifications 3 } -- Conformance alarmConformance OBJECT IDENTIFIER ::= { alarmMIB 2 } alarmCompliances OBJECT IDENTIFIER ::= { alarmConformance 1 } alarmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for systems supporting the Alarm MIB." MODULE -- this module MANDATORY-GROUPS { alarmActiveGroup, alarmModelGroup } GROUP alarmActiveStatsGroup DESCRIPTION "This group is optional." GROUP alarmClearGroup DESCRIPTION "This group is optional." GROUP alarmNotificationsGroup DESCRIPTION "This group is optional." ::= { alarmCompliances 1 } alarmGroups OBJECT IDENTIFIER ::= { alarmConformance 2 } alarmModelGroup OBJECT-GROUP OBJECTS { alarmModelLastChanged, alarmModelNotificationId, alarmModelVarbindIndex, alarmModelVarbindValue, alarmModelDescription, alarmModelSpecificPointer, alarmModelVarbindSubtree, alarmModelResourcePrefix, alarmModelRowStatus } STATUS current DESCRIPTION "Alarm model group." ::= { alarmGroups 1} alarmActiveGroup OBJECT-GROUP OBJECTS { Chisholm & Romascanu Standards Track [Page 32] Alarm MIB June 2003 alarmActiveLastChanged, alarmActiveEngineID, alarmActiveEngineAddressType, alarmActiveEngineAddress, alarmActiveContextName, alarmActiveVariables, alarmActiveNotificationID, alarmActiveResourceId, alarmActiveDescription, alarmActiveLogPointer, alarmActiveModelPointer, alarmActiveSpecificPointer, alarmActiveVariableID, alarmActiveVariableValueType, alarmActiveVariableCounter32Val, alarmActiveVariableUnsigned32Val, alarmActiveVariableTimeTicksVal, alarmActiveVariableInteger32Val, alarmActiveVariableOctetStringVal, alarmActiveVariableIpAddressVal, alarmActiveVariableOidVal, alarmActiveVariableCounter64Val, alarmActiveVariableOpaqueVal } STATUS current DESCRIPTION "Active Alarm list group." ::= { alarmGroups 2} alarmActiveStatsGroup OBJECT-GROUP OBJECTS { alarmActiveStatsActives, alarmActiveStatsActiveCurrent, alarmActiveStatsLastRaise, alarmActiveStatsLastClear } STATUS current DESCRIPTION " Active alarm summary group." ::= { alarmGroups 3} alarmClearGroup OBJECT-GROUP OBJECTS { alarmClearMaximum, alarmClearEngineID, alarmClearEngineAddressType, alarmClearEngineAddress, alarmClearContextName, alarmClearNotificationID, alarmClearResourceId, alarmClearLogIndex, Chisholm & Romascanu Standards Track [Page 33] Alarm MIB June 2003 alarmClearModelPointer } STATUS current DESCRIPTION " Cleared alarm group." ::= { alarmGroups 4} alarmNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { alarmActiveState, alarmClearState } STATUS current DESCRIPTION "The collection of notifications that can be used to model alarms for faults lacking pre-existing notification definitions." ::= { alarmGroups 6 } END 5. ITU Alarm 5.1 Overview This MIB module defines alarm information specific to the alarm model defined in ITU M.3100 [M.3100], X.733[X.733] and X.736[X.736]. This MIB module follows the modular architecture defined by the Alarm MIB, in which the generic Alarm MIB can be augmented by other alarm information defined according to more specific models that define additional behaviour and characteristics. The ituAlarmTable contains information from the ITU Alarm Model about possible alarms in the system. The ituAlarmActiveTable contains information from the ITU Alarm Model about alarms that are currently occurring on the system. The ituAlarmActiveStatsTable provides statistics on current and total alarms. 5.2 IANA Considerations Over time, there will be a need to add new IANAItuProbableCause enumerated values for new probable causes. The Internet Assigned Number Authority (IANA) is responsible for the assignment of all Internet numbers, including various SNMP-related numbers, and specifically, new IANAItuProbableCause and IANAItuEventType values. Values of IANAItuProbableCause less than 1024 are reserved for causes that correspond to ITU probable cause. IANAItuProbableCause of 0 is reserved for special purposes and therefore cannot be assigned. The following shall be used as the initial values, but the latest Chisholm & Romascanu Standards Track [Page 34] Alarm MIB June 2003 values for these textual conventions should be obtained from IANA: IANA-ITU-ALARM-TC DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, mib-2 FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; ianaItuAlarmNumbers MODULE-IDENTITY LAST-UPDATED "200305070000Z" ORGANIZATION "IANA" CONTACT-INFO "Postal: Internet Assigned Numbers Authority Internet Corporation for Assigned Names and Numbers 4676 Admiralty Way, Suite 330 Marina del Rey, CA 90292-6601 USA Tel: +1 310-823-9358 E-Mail: iana@iana.org" DESCRIPTION "The MIB module defines the ITU Alarm textual convention for objects expected to require regular extension. Copyright (C) The Internet Society (2003). The initial version of this MIB module was published in RFC xxxx. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html" REVISION "200305070000Z" DESCRIPTION "Initial version, published as RFC yyyy." -- RFC-Editor assigns yyyy ::= { mib-2 XX } -- to be assigned by IANA IANAItuProbableCause ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "ITU probable cause values. Duplicate values defined in X.733 are appended with X733 to ensure uniqueness. Probable cause value 0 is reserved for special purposes. The Internet Assigned Number Authority (IANA) is responsible for the assignment of all Internet numbers, including various SNMP-related numbers, and specifically, new IANAItuProbableCause values. Values of IANAItuProbableCause less than 1024 are reserved for causes that correspond to ITU probable cause. IANAItuProbableCause of 0 is reserved for special purposes and therefore cannot Chisholm & Romascanu Standards Track [Page 35] Alarm MIB June 2003 be assigned. See http://www.iana.org" REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992 ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" SYNTAX INTEGER { -- The following probable causes were defined in M.3100 aIS (1), callSetUpFailure (2), degradedSignal (3), farEndReceiverFailure (4), framingError (5), lossOfFrame (6), lossOfPointer (7), lossOfSignal (8), payloadTypeMismatch (9), transmissionError (10), remoteAlarmInterface (11), excessiveBER (12), pathTraceMismatch (13), unavailable (14), signalLabelMismatch (15), lossOfMultiFrame (16), receiveFailure (17), transmitFailure (18), modulationFailure (19), demodulationFailure (20), broadcastChannelFailure (21), connectionEstablishmentError (22), invalidMessageReceived (23), localNodeTransmissionError (24), remoteNodeTransmissionError (25), routingFailure (26), --Values 27-50 are reserved for communications alarm related --probable causes -- The following are used with equipment alarm. backplaneFailure (51), dataSetProblem (52), equipmentIdentifierDuplication (53), externalIFDeviceProblem (54), lineCardProblem (55), multiplexerProblem (56), nEIdentifierDuplication (57), powerProblem (58), Chisholm & Romascanu Standards Track [Page 36] Alarm MIB June 2003 processorProblem (59), protectionPathFailure (60), receiverFailure (61), replaceableUnitMissing (62), replaceableUnitTypeMismatch (63), synchronizationSourceMismatch (64), terminalProblem (65), timingProblem (66), transmitterFailure (67), trunkCardProblem (68), replaceableUnitProblem (69), realTimeClockFailure (70), --An equipment alarm to be issued if the system detects that the --real time clock has failed antennaFailure (71), batteryChargingFailure (72), diskFailure (73), frequencyHoppingFailure (74), iODeviceError (75), lossOfSynchronisation (76), lossOfRedundancy (77), powerSupplyFailure (78), signalQualityEvaluationFailure (79), tranceiverFailure (80), protectionMechanismFailure (81), protectingResourceFailure (82), -- Values 83-100 are reserved for equipment alarm related probable -- causes -- The following are used with environmental alarm. airCompressorFailure (101), airConditioningFailure (102), airDryerFailure (103), batteryDischarging (104), batteryFailure (105), commercialPowerFailure (106), coolingFanFailure (107), engineFailure (108), fireDetectorFailure (109), fuseFailure (110), generatorFailure (111), lowBatteryThreshold (112), pumpFailure (113), rectifierFailure (114), rectifierHighVoltage (115), rectifierLowFVoltage (116), ventilationsSystemFailure (117), enclosureDoorOpen (118), explosiveGas (119), fire (120), flood (121), highHumidity (122), highTemperature (123), Chisholm & Romascanu Standards Track [Page 37] Alarm MIB June 2003 highWind (124), iceBuildUp (125), intrusionDetection (126), lowFuel (127), lowHumidity (128), lowCablePressure (129), lowTemperatue (130), lowWater (131), smoke (132), toxicGas (133), coolingSystemFailure (134), externalEquipmentFailure (135), externalPointFailure (136), -- Values 137-150 are reserved for environmental alarm related -- probable causes -- The following are used with Processing error alarm. storageCapacityProblem (151), memoryMismatch (152), corruptData (153), outOfCPUCycles (154), sfwrEnvironmentProblem (155), sfwrDownloadFailure (156), lossOfRealTimel (157), --A processing error alarm to be issued after the system has --reinitialised. This will indicate --to the management systems that the view they have of the managed --system may no longer --be valid. Usage example: The managed --system issues this alarm after a reinitialization with severity --warning to inform the --management system about the event. No clearing notification will --be sent. applicationSubsystemFailure (158), configurationOrCustomisationError (159), databaseInconsistency (160), fileError (161), outOfMemory (162), softwareError (163), timeoutExpired (164), underlayingResourceUnavailable (165), versionMismatch (166), --Values 168-200 are reserved for processing error alarm related -- probable causes. bandwidthReduced (201), congestion (202), excessiveErrorRate (203), excessiveResponseTime (204), excessiveRetransmissionRate (205), reducedLoggingCapability (206), systemResourcesOverload (207 ), -- The following were defined X.733 adapterError (500), Chisholm & Romascanu Standards Track [Page 38] Alarm MIB June 2003 applicationSubsystemFailture (501), bandwidthReducedX733 (502), callEstablishmentError (503), communicationsProtocolError (504), communicationsSubsystemFailure (505), configurationOrCustomizationError (506), congestionX733 (507), coruptData (508), cpuCyclesLimitExceeded (509), dataSetOrModemError (510), degradedSignalX733 (511), dteDceInterfaceError (512), enclosureDoorOpenX733 (513), equipmentMalfunction (514), excessiveVibration (515), fileErrorX733 (516), fireDetected (517), framingErrorX733 (518), heatingVentCoolingSystemProblem (519), humidityUnacceptable (520), inputOutputDeviceError (521), inputDeviceError (522), lanError (523), leakDetected (524), localNodeTransmissionErrorX733 (525), lossOfFrameX733 (526), lossOfSignalX733 (527), materialSupplyExhausted (528), multiplexerProblemX733 (529), outOfMemoryX733 (530), ouputDeviceError (531), performanceDegraded (532), powerProblems (533), pressureUnacceptable (534), processorProblems (535), pumpFailureX733 (536), queueSizeExceeded (537), receiveFailureX733 (538), receiverFailureX733 (539), remoteNodeTransmissionErrorX733 (540), resourceAtOrNearingCapacity (541), responseTimeExecessive (542), retransmissionRateExcessive (543), softwareErrorX733 (544), softwareProgramAbnormallyTerminated (545), softwareProgramError (546), storageCapacityProblemX733 (547), temperatureUnacceptable (548), thresholdCrossed (549), timingProblemX733 (550), toxicLeakDetected (551), transmitFailureX733 (552), Chisholm & Romascanu Standards Track [Page 39] Alarm MIB June 2003 transmiterFailure (553), underlyingResourceUnavailable (554), versionMismatchX733 (555), -- The following are defined in X.736 authenticationFailure (600), breachOfConfidentiality (601), cableTamper (602), delayedInformation (603), denialOfService (604), duplicateInformation (605), informationMissing (606), informationModificationDetected (607), informationOutOfSequence (608), keyExpired (609), nonRepudiationFailure (610), outOfHoursActivity (611), outOfService (612), proceduralError (613), unauthorizedAccessAttempt (614), unexpectedInformation (615), other (1024) } IANAItuEventType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The ITU event Type values. The Internet Assigned Number Authority (IANA) is responsible for the assignment of all Internet numbers, including various SNMP-related numbers, and specifically, new IANAEventType values. See http://www.iana.org " REFERENCE "ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" SYNTAX INTEGER { other (1), communicationsAlarm (2), qualityOfServiceAlarm (3), processingErrorAlarm (4), equipmentAlarm (5), environmentalAlarm (6), integrityViolation (7), operationalViolation (8), physicalViolation (9), securityServiceOrMechanismViolation (10), timeDomainViolation (11) } Chisholm & Romascanu Standards Track [Page 40] Alarm MIB June 2003 END 5.3 Textual Conventions ITU-ALARM-TC DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, mib-2 FROM SNMPv2-SMI TEXTUAL-CONVENTION FROM SNMPv2-TC; ituAlarmTc MODULE-IDENTITY LAST-UPDATED "200305070000Z" ORGANIZATION "IETF Distributed Management Working Group" CONTACT-INFO " WG EMail: disman@ietf.org Subscribe: disman-request@ietf.org http://www.ietf.org/html.charters/disman-charter.html Chair: Randy Presuhn randy_presuhn@mindspring.com Editors: Sharon Chisholm Nortel Networks PO Box 3511 Station C Ottawa, Ont. K1Y 4H7 Canada schishol@nortelnetworks.com Dan Romascanu Avaya Inc. Atidim Technology Park, Bldg. #3 Tel Aviv, 61131 Israel Tel: +972-3-645-8414 Email: dromasca@avaya.com" DESCRIPTION "The MIB module defines the ITU Alarm textual convention for objects not expected to require regular extension. Copyright (C) The Internet Society (2003). The initial version of this MIB module was published in RFC xxxx. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html" -- RFC Ed.: replace yyyy with actual RFC number & remove -- this note REVISION "200305070000Z" DESCRIPTION "Initial version, published as RFC yyyy." -- RFC-Editor assigns yyyy ::= { mib-2 XX } -- to be assigned by IANA Chisholm & Romascanu Standards Track [Page 41] Alarm MIB June 2003 ItuPerceivedSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "ITU perceived severity values" REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992" SYNTAX INTEGER { cleared (1), indeterminate (2), critical (3), major (4), minor (5), warning (6) } ItuTrendIndication ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "ITU trend indication values for alarms." REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992" SYNTAX INTEGER { moreSevere (1), noChange (2), lessSevere (3) } END 5.4 Definitions ITU-ALARM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, mib-2 FROM SNMPv2-SMI AutonomousType, RowPointer FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB Chisholm & Romascanu Standards Track [Page 42] Alarm MIB June 2003 alarmListName, alarmModelIndex, alarmActiveDateAndTime, alarmActiveIndex FROM ALARM-MIB ItuPerceivedSeverity, ItuTrendIndication FROM ITU-ALARM-TC IANAItuProbableCause, IANAItuEventType FROM IANA-ITU-ALARM-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; ituAlarmMIB MODULE-IDENTITY LAST-UPDATED "200305070000Z" ORGANIZATION "IETF Distributed Management Working Group" CONTACT-INFO "WG EMail: disman@ietf.org Subscribe: disman-request@ietf.org http://www.ietf.org/html.charters/disman-charter.html Chair: Randy Presuhn randy_presuhn@mindspring.com Editors: Sharon Chisholm Nortel Networks PO Box 3511 Station C Ottawa, Ont. K1Y 4H7 Canada schishol@nortelnetworks.com Dan Romascanu Avaya Inc. Atidim Technology Park, Bldg. #3 Tel Aviv, 61131 Israel Tel: +972-3-645-8414 Email: dromasca@avaya.com" DESCRIPTION "The MIB module describes ITU Alarm information as defined in ITU Recommendation M.3100 [M.3100], X.733 [X.733] and X.736 [X.736]. Copyright (C) The Internet Society (2003). The initial version of this MIB module was published in RFC xxxx. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html" -- RFC Ed.: replace yyyy with actual RFC number & remove -- this note REVISION "200305070000Z" DESCRIPTION "Initial version, published as RFC yyyy." -- RFC-Editor assigns yyyy ::= { mib-2 XX } -- to be assigned by IANA Chisholm & Romascanu Standards Track [Page 43] Alarm MIB June 2003 ituAlarmObjects OBJECT IDENTIFIER ::= { ituAlarmMIB 1 } ituAlarmModel OBJECT IDENTIFIER ::= { ituAlarmObjects 1 } ituAlarmActive OBJECT IDENTIFIER ::= { ituAlarmObjects 2 } ituAlarmTable OBJECT-TYPE SYNTAX SEQUENCE OF ItuAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of ITU Alarm information for possible alarms on the system." ::= { ituAlarmModel 1 } ituAlarmEntry OBJECT-TYPE SYNTAX ItuAlarmEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries appear in this table for each possible alarm severity." INDEX { alarmListName, alarmModelIndex, ituAlarmPerceivedSeverity } ::= { ituAlarmTable 1 } ItuAlarmEntry ::= SEQUENCE { ituAlarmPerceivedSeverity ItuPerceivedSeverity, ituAlarmEventType IANAItuEventType, ituAlarmProbableCause IANAItuProbableCause, ituAlarmAdditionalText SnmpAdminString, ituAlarmGenericModel RowPointer } ituAlarmPerceivedSeverity OBJECT-TYPE SYNTAX ItuPerceivedSeverity MAX-ACCESS not-accessible STATUS current DESCRIPTION " ITU perceived severity values." REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992" ::= { ituAlarmEntry 1 } ituAlarmEventType OBJECT-TYPE SYNTAX IANAItuEventType MAX-ACCESS read-write STATUS current Chisholm & Romascanu Standards Track [Page 44] Alarm MIB June 2003 DESCRIPTION " Represents the event type values for the alarms" REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992 ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" ::= { ituAlarmEntry 2 } ituAlarmProbableCause OBJECT-TYPE SYNTAX IANAItuProbableCause MAX-ACCESS read-write STATUS current DESCRIPTION " ITU probable cause values." REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992 ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" ::= { ituAlarmEntry 3 } ituAlarmAdditionalText OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION " Represents the additional text field for the alarm." REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992" ::= { ituAlarmEntry 4} ituAlarmGenericModel OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-write STATUS current DESCRIPTION "This object points to the corresponding Chisholm & Romascanu Standards Track [Page 45] Alarm MIB June 2003 row in the alarmModelTable for this alarm severity." ::= { ituAlarmEntry 5 } -- ITU Active Alarm Table -- ituAlarmActiveTable OBJECT-TYPE SYNTAX SEQUENCE OF ItuAlarmActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of ITU information for active alarms entries." ::= { ituAlarmActive 1 } ituAlarmActiveEntry OBJECT-TYPE SYNTAX ItuAlarmActiveEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entries appear in this table when alarms are active. They are removed when the alarm is no longer occurring." INDEX { alarmListName, alarmActiveDateAndTime, alarmActiveIndex } ::= { ituAlarmActiveTable 1 } ItuAlarmActiveEntry ::= SEQUENCE { ituAlarmActiveTrendIndication ItuTrendIndication, ituAlarmActiveDetector AutonomousType, ituAlarmActiveServiceProvider AutonomousType, ituAlarmActiveServiceUser AutonomousType } ituAlarmActiveTrendIndication OBJECT-TYPE SYNTAX ItuTrendIndication MAX-ACCESS read-only STATUS current DESCRIPTION " Represents the trend indication values for the alarms." REFERENCE "ITU Recommendation M.3100, 'Generic Network Information Model', 1995 ITU Recommendation X.733, 'Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function', 1992" ::= { ituAlarmActiveEntry 1 } ituAlarmActiveDetector OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the SecurityAlarmDetector object." REFERENCE Chisholm & Romascanu Standards Track [Page 46] Alarm MIB June 2003 "ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" ::= { ituAlarmActiveEntry 2 } ituAlarmActiveServiceProvider OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the ServiceProvider object." REFERENCE "ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" ::= { ituAlarmActiveEntry 3 } ituAlarmActiveServiceUser OBJECT-TYPE SYNTAX AutonomousType MAX-ACCESS read-only STATUS current DESCRIPTION "Represents the ServiceUser object." REFERENCE "ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" ::= { ituAlarmActiveEntry 4 } -- Statistics and Counters ituAlarmActiveStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ItuAlarmActiveStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table represents the ITU alarm statistics information." ::= { ituAlarmActive 2 } ituAlarmActiveStatsEntry OBJECT-TYPE SYNTAX ItuAlarmActiveStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Statistics on the current active ITU alarms." INDEX { alarmListName } ::= { ituAlarmActiveStatsTable 1 } Chisholm & Romascanu Standards Track [Page 47] Alarm MIB June 2003 ItuAlarmActiveStatsEntry ::= SEQUENCE { ituAlarmActiveStatsIndeterminateCurrent Gauge32, ituAlarmActiveStatsCriticalCurrent Gauge32, ituAlarmActiveStatsMajorCurrent Gauge32, ituAlarmActiveStatsMinorCurrent Gauge32, ituAlarmActiveStatsWarningCurrent Gauge32, ituAlarmActiveStatsIndeterminates Counter32, ituAlarmActiveStatsCriticals Counter32, ituAlarmActiveStatsMajors Counter32, ituAlarmActiveStatsMinors Counter32, ituAlarmActiveStatsWarnings Counter32 } ituAlarmActiveStatsIndeterminateCurrent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the current number of active alarms with a ituAlarmPerceivedSeverity of indeterminate." ::= { ituAlarmActiveStatsEntry 1 } ituAlarmActiveStatsCriticalCurrent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the current number of active alarms with a ituAlarmPerceivedSeverity of critical." ::= { ituAlarmActiveStatsEntry 2 } ituAlarmActiveStatsMajorCurrent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the current number of active alarms with a ituAlarmPerceivedSeverity of major." ::= { ituAlarmActiveStatsEntry 3 } ituAlarmActiveStatsMinorCurrent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the current number of active alarms with a ituAlarmPerceivedSeverity of minor." ::= { ituAlarmActiveStatsEntry 4 } Chisholm & Romascanu Standards Track [Page 48] Alarm MIB June 2003 ituAlarmActiveStatsWarningCurrent OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the current number of active alarms with a ituAlarmPerceivedSeverity of warning." ::= { ituAlarmActiveStatsEntry 5 } ituAlarmActiveStatsIndeterminates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the total number of active alarms with a ituAlarmPerceivedSeverity of indeterminate since system restart." ::= { ituAlarmActiveStatsEntry 6 } ituAlarmActiveStatsCriticals OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the total number of active alarms with a ituAlarmPerceivedSeverity of critical since system restart." ::= { ituAlarmActiveStatsEntry 7 } ituAlarmActiveStatsMajors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the total number of active alarms with a ituAlarmPerceivedSeverity of major since system restart." ::= { ituAlarmActiveStatsEntry 8 } ituAlarmActiveStatsMinors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the total number of active alarms with a ituAlarmPerceivedSeverity of minor since system restart." ::= { ituAlarmActiveStatsEntry 9 } ituAlarmActiveStatsWarnings OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the total number of active alarms with a Chisholm & Romascanu Standards Track [Page 49] Alarm MIB June 2003 ituAlarmPerceivedSeverity of warning since system restart." ::= { ituAlarmActiveStatsEntry 10 } -- Conformance ituAlarmConformance OBJECT IDENTIFIER ::= { ituAlarmMIB 2 } ituAlarmCompliances OBJECT IDENTIFIER ::= { ituAlarmConformance 1 } ituAlarmCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for systems supporting the ITU Alarm MIB." MODULE -- this module MANDATORY-GROUPS { ituAlarmGroup } GROUP ituAlarmServiceUserGroup DESCRIPTION "This group is optional." GROUP ituAlarmSecurityGroup DESCRIPTION "This group is optional." GROUP ituAlarmStatisticsGroup DESCRIPTION "This group is optional." ::= { ituAlarmCompliances 1 } ituAlarmGroups OBJECT IDENTIFIER ::= { ituAlarmConformance 2 } ituAlarmGroup OBJECT-GROUP OBJECTS { ituAlarmEventType, ituAlarmProbableCause, ituAlarmGenericModel } STATUS current DESCRIPTION "ITU alarm details list group." ::= { ituAlarmGroups 1} ituAlarmServiceUserGroup OBJECT-GROUP OBJECTS { ituAlarmAdditionalText, ituAlarmActiveTrendIndication } STATUS current DESCRIPTION "The use of these parameters is a service-user option." ::= { ituAlarmGroups 2 } ituAlarmSecurityGroup OBJECT-GROUP Chisholm & Romascanu Standards Track [Page 50] Alarm MIB June 2003 OBJECTS { ituAlarmActiveDetector, ituAlarmActiveServiceProvider, ituAlarmActiveServiceUser } STATUS current DESCRIPTION "Security Alarm Reporting Function" REFERENCE "ITU Recommendation X.736, 'Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function', 1992" ::= { ituAlarmGroups 3 } ituAlarmStatisticsGroup OBJECT-GROUP OBJECTS { ituAlarmActiveStatsIndeterminateCurrent, ituAlarmActiveStatsCriticalCurrent, ituAlarmActiveStatsMajorCurrent, ituAlarmActiveStatsMinorCurrent, ituAlarmActiveStatsWarningCurrent, ituAlarmActiveStatsIndeterminates, ituAlarmActiveStatsCriticals, ituAlarmActiveStatsMajors, ituAlarmActiveStatsMinors, ituAlarmActiveStatsWarnings } STATUS current DESCRIPTION "ITU Active Alarm Statistics." ::= { ituAlarmGroups 4 } END 6. Examples 6.1 Alarms Based on linkUp/linkDown Notifications This example demonstrates an interface-based alarm that goes into a state of "warning" when a linkDown Notification occurs but the ifAdminStatus indicates the interface was taken down administratively. If IfAdminStatus is "up" when the linkDown Notification occurs, then there is a problem, so the state of the alarm is critical. A linkUp alarm clears the alarm. linkDown NOTIFICATION-TYPE OBJECTS { ifIndex, ifAdminStatus, ifOperStatus } STATUS current DESCRIPTION "" ::= { snmpTraps 3 } Chisholm & Romascanu Standards Track [Page 51] Alarm MIB June 2003 linkUp NOTIFICATION-TYPE OBJECTS { ifIndex, ifAdminStatus, ifOperStatus } STATUS current DESCRIPTION "" ::= { snmpTraps 4 } alarmModelIndex 3 alarmModelState 1 alarmModelNotificationId linkUp alarmModelVarbindIndex 0 alarmModelVarbindValue 0 alarmModelDescription "linkUp" alarmModelSpecificPointer ituAlarmEntry.3.1 alarmModelVarbindSubtree ifIndex (1.3.6.1.2.1.2.2.1.1) alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType communicationsAlarm (2) ituAlarmPerceivedSeverity cleared (1) ituAlarmGenericModel alarmModelEntry.3.1 alarmModelIndex 3 alarmModelState 2 alarmModelNotificationId linkDown alarmModelVarbindIndex 2 alarmModelVarbindValue down (2) alarmModelDescription "linkDown administratively" alarmModelSpecificPointer ituAlarmEntry.3.6 alarmModelVarbindSubtree ifIndex (1.3.6.1.2.1.2.2.1.1) alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType communicationsAlarm (2) ituAlarmPerceivedSeverity warning (6) ituAlarmGenericModel alarmModelEntry.3.2 alarmModelIndex 3 alarmModelState 3 alarmModelNotificationId linkDown alarmModelVarbindIndex 2 alarmModelVarbindValue up (1) alarmModelDescription "linkDown - confirmed problem" alarmModelSpecificPointer ituAlarmEntry.3.3 alarmModelVarbindSubtree ifIndex (1.3.6.1.2.1.2.2.1.1) alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType communicationsAlarm (2) ituAlarmPerceivedSeverity critical (3) ituAlarmGenericModel alarmModelEntry.3.3 alarmActiveIndex 1 Chisholm & Romascanu Standards Track [Page 52] Alarm MIB June 2003 alarmActiveTime 2342464573 alarmActiveDateAndTime DateAndTime, alarmActiveEngineID SnmpEngineID, alarmActiveEngineAddressType ipV4 alarmActiveEngineAddress 10.10.10.10 alarmActiveContextName SnmpAdminString, alarmActiveVariables 3 alarmActiveNotificationID 1.3.6.1.6.3.1.1.5.3 alarmActiveResourceId 1.3.6.1.2.1.2.2.1.1.346 alarmActiveLogPointer 0.0 alarmActiveModelPointer alarmModelEntry.3.3 alarmActiveSpecificPointer ituAlarmActiveEntry.1.3 ituAlarmActiveTrendIndication moreSevere (1) ituAlarmDetector 0.0 ituAlarmServiceProvider 0.0 ituAlarmServiceUser 0.0 alarmActiveVariableIndex 1 alarmActiveVariableID sysUpTime.0 alarmActiveVariableValueType timeTicks(3) alarmActiveVariableCounter32Val 0 alarmActiveVariableUnsigned32Val 0 alarmActiveVariableTimeTicksVal 46754 alarmActiveVariableInteger32Val 0 alarmActiveVariableOctetStringVal "" alarmActiveVariableIpAddressVal 0 alarmActiveVariableOidVal 0.0 alarmActiveVariableCounter64Val 0 alarmActiveVariableIndex 2 alarmActiveVariableID snmpTrapOID.0 alarmActiveVariableValueType objectId(7) alarmActiveVariableCounter32Val 0 alarmActiveVariableUnsigned32Val 0 alarmActiveVariableTimeTicksVal 0 alarmActiveVariableInteger32Val 0 alarmActiveVariableOctetStringVal "" alarmActiveVariableIpAddressVal 0 alarmActiveVariableOidVal 1.3.6.1.6.3.1.1.5.3 alarmActiveVariableCounter64Val 0 alarmActiveVariableIndex 3 alarmActiveVariableID ifIndex alarmActiveVariableValueType integer32(4) alarmActiveVariableCounter32Val 0 alarmActiveVariableUnsigned32Val 0 alarmActiveVariableTimeTicksVal 0 alarmActiveVariableInteger32Val 346 alarmActiveVariableOctetStringVal "" alarmActiveVariableIpAddressVal 0 alarmActiveVariableOidVal 0.0 alarmActiveVariableCounter64Val 0 alarmActiveVariableIndex 4 alarmActiveVariableID ifAdminStatus Chisholm & Romascanu Standards Track [Page 53] Alarm MIB June 2003 alarmActiveVariableValueType integer32(4) alarmActiveVariableCounter32Val 0 alarmActiveVariableUnsigned32Val 0 alarmActiveVariableTimeTicksVal 0 alarmActiveVariableInteger32Val up (1) alarmActiveVariableOctetStringVal "" alarmActiveVariableIpAddressVal 0 alarmActiveVariableOidVal 0.0 alarmActiveVariableCounter64Val 0 alarmActiveVariableIndex 5 alarmActiveVariableID ifOperStatus alarmActiveVariableValueType integer32(4) alarmActiveVariableCounter32Val 0 alarmActiveVariableUnsigned32Val 0 alarmActiveVariableTimeTicksVal 0 alarmActiveVariableInteger32Val down(2) alarmActiveVariableOctetStringVal "" alarmActiveVariableIpAddressVal 0 alarmActiveVariableOidVal 0.0 alarmActiveVariableCounter64Val 0 alarmActiveVariableOpaqueVal 6.2 Temperature Alarms Using Generic Notifications Consider a system able to detect four different temperature states for a widget - normal, minor, major, critical. The system does not have any Notification definitions for these alarm states. A temperature alarm can be modelled using the generic alarm Notifications of alarmClearState and alarmActive. alarmModelIndex 5 alarmModelState 1 alarmModelNotificationId alarmClearState alarmModelVarbindIndex 2 alarmModelVarbindValue cleared (1) alarmModelDescription "Acme Widget Temperature Normal" alarmModelSpecificPointer ituAlarmEntry.5.1 alarmModelVarbindSubtree alarmActiveResourceId alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType environmentalAlarm (6) ituPerceivedSeverity cleared (1) ituAlarmGenericModel alarmModelEntry.5.1 alarmModelIndex 5 alarmModelState 2 alarmModelNotificationId alarmActiveState alarmModelVarbindIndex 2 alarmModelVarbindValue minor (5) alarmModelDescription "Acme Widget Temperature Minor" alarmModelSpecificPointer ituAlarmEntry.5.5 Chisholm & Romascanu Standards Track [Page 54] Alarm MIB June 2003 alarmModelVarbindSubtree alarmActiveResourceId alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventState environmentalAlarm (6) ituPerceivedSeverity minor (5) ituAlarmGenericModel alarmModelEntry.5.2 alarmModelIndex 5 alarmModelState 3 alarmModelNotificationId alarmActiveState alarmModelVarbindIndex 2 alarmModelVarbindValue major (4) alarmModelDescription "Acme Widget Temperature Major" alarmModelSpecificPointer ituAlarmEntry.5.4 alarmModelVarbindSubtree alarmActiveResourceId alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType environmentalAlarm (6) ituPerceivedSeverity major (4) ituAlarmGenericModel alarmModelEntry.5.3 alarmModelIndex 5 alarmModelState 4 alarmModelNotificationId alarmActiveState alarmModelVarbindIndex 2 alarmModelVarbindValue critical (3) alarmModelDescription "Acme Widget Temperature Critical" alarmModelSpecificPointer ituAlarmEntry.5.3 alarmModelVarbindSubtree alarmActiveResourceId alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType environmentalAlarm (6) ituPerceivedSeverity critical (3) ituAlarmGenericModel alarmModelEntry.5.4 6.3 Temperature Alarms Without Notifications Consider a system able to detect four different temperature states for a widget - normal, minor, major, critical. The system does not have any Notification definitions for these alarm states. A temperature alarm can be modelled without specifying any Notifications in the alarm model. When a temperature state other than normal is detected, an instance of this alarm would be added to the active alarm table, but no Notifications would be sent out. This could alternatively be accomplished using the models from example 6.2 and by not specifying any target managers in the SNMP-TARGET-MIB, which would allow the alarm state Notifications to be logged in the Notification log while Chisholm & Romascanu Standards Track [Page 55] Alarm MIB June 2003 still preventing Notifications from being transmitted on the wire. alarmModelIndex 6 alarmModelState 1 alarmModelNotificationId 0.0 alarmModelVarbindIndex 0 alarmModelVarbindValue 0 alarmModelDescription "Widget Temperature" alarmModelSpecificPointer ituAlarmEntry.6.1 alarmModelVarbindSubtree 0.0 alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType environmentalAlarm (6) ituPerceivedSeverity cleared (1) ituAlarmGenericModel alarmModelEntry.6.1 alarmModelIndex 6 alarmModelState 2 alarmModelNotificationId 0.0 alarmModelVarbindIndex 0 alarmModelVarbindValue 0 alarmModelDescription "Widget Temperature" alarmModelSpecificPointer ituAlarmEntry.6.5 alarmModelVarbindSubtree 0.0 alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventState environmentalAlarm (6) ituAlarmPerceivedSeverity minor (5) ituAlarmGenericModel alarmModelEntry.6.2 alarmModelIndex 6 alarmModelState 3 alarmModelNotificationId 0.0 alarmModelVarbindIndex 0 alarmModelVarbindValue 0 alarmModelDescription "Widget Temperature" alarmModelSpecificPointer ituAlarmEntry.6.4 alarmModelVarbindSubtree 0.0 alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType environmentalAlarm (6) ituPerceivedSeverity major (4) ituAlarmGenericModel alarmModelEntry.6.3 alarmModelIndex 6 alarmModelState 4 alarmModelNotificationId 0.0 alarmModelVarbindIndex 0 alarmModelVarbindValue 0 Chisholm & Romascanu Standards Track [Page 56] Alarm MIB June 2003 alarmModelDescription "Widget Temperature Severe" alarmModelSpecificPointer ituAlarmEntry.6.3 alarmModelVarbindSubtree 0.0 alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) ituAlarmEventType environmentalAlarm (6) ituPerceivedSeverity critical (3) ituAlarmGenericModel alarmModelEntry.6.4 6.4 Printer MIB Alarm Example Consider the following Notifications defined in the printer MIB [RFC1759]: prtAlertSeverityLevel OBJECT-TYPE -- This value is a type 1 enumeration SYNTAX INTEGER { other(1), critical(3), warning(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The level of severity of this alert table entry. The printer determines the severity level assigned to each entry into the table." ::= { prtAlertEntry 2 } printerV2Alert NOTIFICATION-TYPE OBJECTS { prtAlertIndex, prtAlertSeverityLevel, prtAlertGroup, prtAlertGroupIndex, prtAlertLocation, prtAlertCode } STATUS current DESCRIPTION "This trap is sent whenever a critical event is added to the prtAlertTable." ::= { printerV2AlertPrefix 1 } These Notifications can be used to model a printer alarm as follows: alarmModelIndex 9 alarmModelState 1 alarmModelNotificationId alarmClearState alarmModelVarbindIndex 0 alarmModelVarbindValue 0 alarmModelDescription "Printer Alarm" alarmModelSpecificPointer 0.0 alarmModelVarbindSubtree prtAlertGroup alarmModelResourcePrefix 0.0 Chisholm & Romascanu Standards Track [Page 57] Alarm MIB June 2003 alarmModelRowStatus active (1) alarmModelIndex 9 alarmModelState 2 alarmModelNotificationId printerV2Alert alarmModelVarbindIndex 2 alarmModelVarbindValue warning (4) alarmModelDescription "Printer Alarm" alarmModelSpecificPointer 0.0 alarmModelVarbindSubtree prtAlertGroup alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) alarmModelIndex 9 alarmModelState 3 alarmModelNotificationId printerV2Alert alarmModelVarbindIndex 2 alarmModelVarbindValue other (1) alarmModelDescription "Printer Alarm - unknown severity" alarmModelSpecificPointer 0.0 alarmModelVarbindSubtree prtAlertGroup alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) alarmModelIndex 9 alarmModelState 4 alarmModelNotificationId printerV2Alert alarmModelVarbindIndex 2 alarmModelVarbindValue critical (3) alarmModelDescription "Printer Alarm" alarmModelSpecificPointer 0.0 alarmModelVarbindSubtree prtAlertGroup alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) 6.5 RMON Alarm Example The RMON MIB [RFC2819] defines a mechanism for generating threshold alarms. When the thresholds are crossed, RisingAlarm and FallingAlarm Notifications are generated as appropriate. These Notifications can be used to model an upper threshold alarm as follows: alarmModelIndex 6 alarmModelState 1 alarmModelNotificationId FallingAlarm alarmModelVarbindIndex 0 alarmModelVarbindValue 0 alarmModelDescription "RMON Rising Clear Alarm" alarmModelSpecificPointer 0.0 alarmModelVarbindSubtree alarmIndex Chisholm & Romascanu Standards Track [Page 58] Alarm MIB June 2003 alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) alarmModelIndex 6 alarmModelState 2 alarmModelNotificationId RisingAlarm alarmModelVarbindIndex 0 alarmModelVarbindValue 0 alarmModelDescription "RMON Rising Alarm" alarmModelSpecificPointer 0.0 alarmModelVarbindSubtree alarmIndex alarmModelResourcePrefix 0.0 alarmModelRowStatus active (1) 6.6 The Lifetime of an Alarm The following example demonstrates the relationship between the active alarm table, the clear alarm table and the Notification log MIB. Consider a system with alarms modelled as in example 1 and which also supports the informational Notification dsx3LineStatusChange. dsx3LineStatusChange NOTIFICATION-TYPE OBJECTS { dsx3LineStatus, dsx3LineStatusLastChange } STATUS current DESCRIPTION "A dsx3LineStatusChange trap is sent when the value of an instance of dsx3LineStatus changes. It can be utilized by an NMS to trigger polls. When the line status change results in a lower level line status change (i.e. ds1), then no traps for the lower level are sent." ::= { ds3Traps 0 1 } Chisholm & Romascanu Standards Track [Page 59] Alarm MIB June 2003 0. At system start, the active alarm table, alarm clear table and the Notification log are all empty. ___________________________ _______________________ | alarmActiveTable | | nlmLogTable | |---------------------------| |-----------------------| | alarmActiveIndex | alarm | | nlmLogPointer | notif.| |---------------------------| |-----------------------| |___________________________| |_______________________| __________________________________________________ | alarmClearTable | |--------------------------------------------------| | alarmClear Index | alarm | |--------------------------------------------------| | | | |__________________________________________________| 1. Some time later, a link goes down generating a linkDown Notification, which is sent out and logged in the Notification log. As this Notification is modelled as an alarm state, an entry is added to the active alarm table. __________________________________________________ | alarmActiveTable | |--------------------------------------------------| | alarmActiveIndex | alarm | |--------------------------------------------------| | 1 | link down - problem confirmed | |__________________________________________________| _______________________________________________ | nlmLogTable | |-----------------------------------------------| | nlmLogPointer | Notification | |-----------------------------------------------| | 1 | linkdown | |_______________________________________________| __________________________________________________ | alarmClearTable | |--------------------------------------------------| | alarmClear Index | alarm | |--------------------------------------------------| | | | |__________________________________________________| Chisholm & Romascanu Standards Track [Page 60] Alarm MIB June 2003 2. Some time later, the value of an instance of dsx3LineStatus changes. This Notification is sent out and logged. As this is not modelled into an alarm state, the active alarm table remains unchanged. __________________________________________________ | alarmActiveTable | |--------------------------------------------------| | alarmActiveIndex | alarm | |--------------------------------------------------| | 1 | linkDown - problem confirmed | |__________________________________________________| _____________________________________________ | nlmLogTable | |---------------------------------------------| | nlmLogPointer | Notification | |---------------------------------------------| | 1 | linkDown | | 2 | dsx3LineStatusChange | |_____________________________________________| __________________________________________________ | alarmClearTable | |--------------------------------------------------| | alarmClear Index | alarm | |--------------------------------------------------| | | | |__________________________________________________| Chisholm & Romascanu Standards Track [Page 61] Alarm MIB June 2003 3. Some time later, the link goes back up. A linkUp Notification is sent out and logged. As this Notification models the clear alarm for this alarm, the alarm entry is remove from the active alarm table. An entry is added to the clear alarm table. __________________________________________________ | alarmActiveTable | |--------------------------------------------------| | alarmActiveIndex | alarm | |--------------------------------------------------| |__________________________________________________| _____________________________________________ | nlmLogTable | |---------------------------------------------| | nlmLogPointer | Notification | |---------------------------------------------| | 1 | linkDown | | 2 | dsx3LineStatusChange | | 3 | linkUp | |_____________________________________________| __________________________________________________ | alarmClearTable | |--------------------------------------------------| | alarmClear Index | alarm | |--------------------------------------------------| | 1 | linkDown - confirmed problem | |__________________________________________________| 7. Security Considerations There are a number of management objects defined in this MIB module with a MAX-ACCESS clause of read-write and/or read-create. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. The following objects are defined with a MAX-ACCESS clause of read-write or read-create: alarmModelNotificationId, alarmModelVarbindIndex, alarmModelVarbindValue, alarmModelDescription, alarmModelSpecificPointer, alarmModelVarbindSubtree, alarmModelResourcePrefix, alarmModelRowStatus, ituAlarmEventType, ituAlarmProbableCause, ituAlarmAdditionalText, and ituAlarmGenericModel. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPSec), even then, there is no control as to who on the secure network is Chisholm & Romascanu Standards Track [Page 62] Alarm MIB June 2003 allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. For further discussion of security, see section 3.4. 8. Authors' Addresses Sharon Chisholm Nortel Networks PO Box 3511, Station C Ottawa, Ontario, K1Y 4H7 Canada Email: schishol@nortelnetworks.com Dan Romascanu Avaya Inc. Atidim Technology Park, Bldg. #3 Tel Aviv, 61131 Israel Tel: +972-3-645-8414 Email: dromasca@avaya.com 9. Acknowledgements This document is a product of the DISMAN Working Group. 10. Intellectual Property The IETF takes no position regarding the validity or scope of any intellectual property or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; neither does it represent that it has made any effort to identify any such rights. Information on the IETF's procedures with respect to rights in standards-track and standards-related documentation can be found in RFC 2028. Copies of claims of rights made available for publication and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary Chisholm & Romascanu Standards Track [Page 63] Alarm MIB June 2003 rights by implementors or users of this specification can be obtained from the IETF Secretariat. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights which may cover technology that may be required to practice this standard. Please address the information to the IETF Executive Director. The IETF has been notified of intellectual property rights claimed in regard to some or all of the specification contained in this document. For more information consult the online list of claimed rights. 11. References 11.1 Normative References [M.3100] ITU Recommendation M.3100, "Generic Network Information Model", 1995 [RFC1157] Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network Management Protocol", STD 15, RFC 1157, May 1990. [RFC1212] Rose, M., and K. McCloghrie, "Concise MIB Definitions", STD 16, RFC 1212, March 1991. [RFC1215] M. Rose, "A Convention for Defining Traps for use with the SNMP", RFC 1215, March 1991. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2576] Frye, R., Levi, D., Routhier, S., Wijnen, B., "Coexistence between Version 1, Version 2, and Version 3 of the Internet-standard Network Management Framework.", RFC2576, March 2000 [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose, M., and S. Waldbusser, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999 [RFC3291] Daniele, M., Haberman, B., Routhier, S., Schoenwaelder, Chisholm & Romascanu Standards Track [Page 64] Alarm MIB June 2003 J., "Textual Conventions for Internet Network Addresses", May 2002. [RFC3411] Harrington, D., Presuhn, R., Wijnen, B., "An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks", RFC3411, December 2002. [RFC3413] Levi, D., Meyer, P., and B. Stewart, "SNMPv3 Applications", RFC 3414, December 2002. [RFC3415] Wijnen, B., Presuhn, R., McCloghrie K., "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC3415, December 2002 [RFC3416] Presuhn, R., Ed.., "Version 2 of the Protocol Operations for the Simple Network Management Protocol (SNMP).", RFC 3416, December 2002. [X.733] ITU Recommendation X.733, "Information Technology - Open Systems Interconnection - System Management: Alarm Reporting Function", 1992 [X.736] ITU Recommendation X.736, "Information Technology - Open Systems Interconnection - System Management: Security Alarm Reporting Function", 1992 11.2 Informative References [RFC1759] Smith, R., Wright, F., Hastings, T., Zilles, S., Gullenskop, J., "Printer MIB", RFC 1759, March 1995 [RFC2737] McCloghrie, K., Brierman, A., "Entity MIB using SMIv2", RFC2737, December 1999 [RFC2788] Freed, N., Kille, S., "Network Services Monitoring MIB", RFC2788, March 2000 [RFC2819] Waldbusser, S. "Remote Network Monitoring Management Information Base", RFC 2819, May 2000 [RFC2863] McCloghrie, K., Kastenholz, F., "The Interfaces Group MIB using SMIv2", RFC2863, June 2000 [RFC2981] Kavasseri, R., Stewart, B., "Event MIB", RFC2981, October 2000 [RFC3014] Stewart, B., Kavasseri, R., "Notification Log MIB, RFC 3014, November 2000 [RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002 Chisholm & Romascanu Standards Track [Page 65] Alarm MIB June 2003 12. Full Copyright Statement Copyright (C) The Internet Society (2003). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Chisholm & Romascanu Standards Track [Page 66]