INTERNET-DRAFT Masanori Miyazawa Intended status: Standards Truck KDDI R&D Labs Expires: October 7, 2012 Tomohiro Otani Kenji Kumaki KDDI Corporation Thomas D. Nadeau May 8, 2012 Traffic Engineering Database Management Information Base in support of MPLS-TE/GMPLS draft-ietf-ccamp-gmpls-ted-mib-13.txt Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Copyright Notice Copyright (c) 2012 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. T. Otani et al. Expires Oct. 2012 [Page 1] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 Abstract This memo defines the Management Information Base (MIB) objects in order to manage traffic engineering database (TED) information with extension in support of Multi-Protocol Label Switching (MPLS) with traffic engineering (TE) as well as Generalized MPLS (GMPLS) for use with network management protocols. Table of Contents Status of this Memo................................................... 1 Abstract.............................................................. 2 1. The Internet-Standard Management Framework......................... 3 2. Introduction....................................................... 3 3. Overview........................................................... 3 3.1 Conventions used in this document................................. 3 3.2 Terminology....................................................... 3 3.3 Acronyms.......................................................... 4 4. Motivations........................................................ 4 5. Brief description of MIB Objects................................... 4 5.1 tedTable.......................................................... 4 5.2 tedLocalIfAddrTable............................................... 4 5.3 tedRemoteIfAddrTable.............................................. 4 5.4 tedSwCapTable..................................................... 5 5.5 tedSrlgTable...................................................... 5 6. Example of the TED MIB module usage................................ 5 7. TED MIB Definitions in support of GMPLS............................ 6 8. Security consideration............................................ 28 9. IANA Considerations............................................... 29 9.1 IANA Considerations for TED-MIB.................................. 29 10. References....................................................... 29 10.1 Normative References............................................ 29 10.2 Informative References.......................................... 29 11. Acknowledgment................................................... 31 12. Authors' Addresses............................................... 32 T. Otani et al. Expires Oct. 2012 [Page 2] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 1. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580 [RFC2580]. 2. Introduction The OSPF MIB was originally defined for OSPF version2 in support of IPv4 [RFC4750] and extended to support the Internet Protocol version6(IPv6) as OSPF version3 MIB [RFC5643]. The ISIS MIB is also defined as [RFC4444]. On the other side, MPLS/GMPLS based traffic engineering has so far extended OSPF/ISIS routing protocol with TE functionality [RFC4202], [RFC3630], [RFC5329], [RFC5307], [RFC5305]. To manage such MPLS-TE/GMPLS networks effectively, routing information associated with MPLS/GMPLS TE parameters (TED) is preferred for the network management, however, there is no clear definition of MPLS/GMPLS TE information in existing MIBs related to OSPF(v2 and v3)/ISIS. This memo defines the Management Information Base (MIB) objects for managing TED in support of MPLS-TE/GMPLS for use with network management protocols. This MIB module should be used in conjunction with OSPFv2 MIB, OSPF v3 MIB and ISIS MIB as well as other MIBs defined in [RFC3812], [RFC3813], [RFC4802], [RFC4803] for the management of MPLS/GMPLS based traffic engineering information. 3. Overview 3.1 Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC-2119 [RFC2119]. 3.2 Terminology Definitions of key terms for MPLS OAM and GMPLS are found in [RFC4377] and [RFC3945], and the reader is assumed to be familiar with those definitions which are not repeated here. T. Otani et al. Expires Oct. 2012 [Page 3] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 3.3 Acronyms FSC: Fiber switch capable GMPLS: Generalized Multi-Protocol Label Switching ISIS: Intermediate System to Intermediate System LDP: Label Distribution Protocol LSA: Link state advertisement LSC: Lambda switch capable LSP: Label Switching Path LSR: Label Switching Router MIB: Management Information Base OAM: Operations and Management OA&M: Operations, Administration and Maintenance. OSPF: Open Shortest Path First PSC: Packet switch capable RSVP: Resource reSerVation Protocol SRLG: Shared risk link group TE: Traffic Engineering TED: Traffic Engineering Database TDM: Time Division Multiplexing 4. Motivations The existing OSPFv2, OSPFv3, ISIS, MPLS and GMPLS MIBs do not provide for the management interface to retrieve topology information of MPLS and GMPLS networks. 5. Brief description of MIB Objects The objects described in this section support the management of TED described in [RFC4202], [RFC4203] and [RFC5307] for GMPLS extensions as well as in [RFC3630] and [RFC5305] for MPLS/GMPLS. 5.1 tedTable The tedTable is basically used to indicate TED information of OSPF-TE or ISIS-TE. However, this table does not contain information for Local/Remote interface IP address, Interface Switching Capability Descriptor and Shared Risk Link Group information within the sub-TLVs for the Link-TLV. 5.2 tedLocalIfAddrTable The tedLocalIfAddrTable is identical to the Local interface IP address information in a sub-TLV for the Link-TLV. This is independently defined, because the Interface IP Address sub-TLV may appear more than once within the same Link-TLV. 5.3 tedRemoteIfAddrTable The tedRemoteIfAddrTable is identical to the Remote interface IP address information in a sub-TLV of the Link-TLV. Also, this is T. Otani et al. Expires Oct. 2012 [Page 4] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 utilized independently because one or more local interface IP address sub TLVs may exist in the same Link-TLV. 5.4 tedSwCapTable The tedSwCapTable represents Interface Switching Capability Descriptor information. This is independently defined due to the possibility of multiple appearances of the sub TLV within the same Link-TLV. 5.5 tedSrlgTable The tedSrlgTable contains the Sub-TLV information of Shared Risk Link Group (SRLG) information. This is separately defined, because more than one sub TLVs may appear in the same Link-TLV. 6.Example of the TED MIB Module Usage In this section, we provide an example of the TED MIB module usage. The following indicates the information of a numbered TE link originated in a GMPLS controlled node. When TE link information is retrieved in a MPLS network, GMPLS specific objects such as tedLocalIfAddrTable, tedRemoteIfAddrTable, tedSwCapTable and tedSrlgTable are not supported. Note that the TED MIB modules are only limited to "read-only" access except for tedCreatedDeletedNotificationMaxRate and tedStatusChangeNotificationMaxRate. The TED MIB is designed to be independent of OSPF or ISIS MIBs, however each TE link information belongs to a node or a link which is managed by the routing protocol. In tedTable: { tedLinkInformationData.3232235777.3232235778.2.16777264 zeroDotZero tedLinkType.3232235777.3232235778.2.16777264 pointToPoint(1) tedLinkState.3232235777.3232235778.2.16777264 up(1) tedAreaId.3232235777.3232235778.2.16777264 0 tedRouterIdAddrType.3232235777.3232235778.2.16777264 ipv4(1) tedRouterIdAddr.3232235777.3232235778.2.16777264 192.0.2.1 tedLinkIdAddrType.3232235777.3232235778.2.16777264 ipv4(1) tedLinkIdAddr.3232235777.3232235778.2.16777264 192.0.2.10 tedMetric.3232235777.3232235778.2.16777264 1 tedMaxBandwidth.3232235777.3232235778.2.16777264 4d9450c0 tedMaxReservableBandwidth.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri0.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri1.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri2.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri3.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri4.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri5.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri6.3232235777.3232235778.2.16777264 4d9450c0 tedUnreservedBandwidthPri7.3232235777.3232235778.2.16777264 4d9450c0 tedAdministrativeGroup.3232235777.3232235778.2.16777264 0 T. Otani et al. Expires Oct. 2012 [Page 5] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 tedLocalId.3232235777.3232235778.2.16777264 0 tedRemoteId.3232235777.3232235778.2.16777264 0 tedLinkProtectionType.3232235777.3232235778.2.16777264 01 00 00 00 7 In tedLocalIfAddrTable: { tedLocalIfAddrType.16777264.192.0.2.21 ipv4(1) } In tedRemoteIfAddrTable: { tedRemoteIfAddrType.16777264.192.0.2.22 ipv4(1) } In tedSwCapTable: { tedSwCapType.16777264.1 lsc(150) tedSwCapEncoding.16777264.1 ethernet(2) tedSwCapMaxLspBandwidthPri0.16777264.1 4d9450c0 tedSwCapMaxLspBandwidthPri1.16777264.1 4d9450c0 tedSwCapMaxLspBandwidthPri2.16777264.1 4d9450c0 tedSwCapMaxLspBandwidthPri3.16777264.1 4d9450c0 tedSwCapMaxLspBandwidthPri4.16777264.1 4d9450c0 tedSwCapMaxLspBandwidthPri5.16777264.1 4d9450c0 tedSwCapMaxLspBandwidthPri6.16777264.1 4d9450c0 tedSwCapMaxLspBandwidthPri7.16777264.1 4d9450c0 tedSwCapMinLspBandwidth.16777264.1 0 tedSwCapIfMtu.16777264.1 0 tedSwCapIndication.16777264.1 standard(0) } In tedSrlgTable: { tedSrlg.16777264.1 0 } 7. TED MIB Definitions in support of GMPLS TED-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Unsigned32, transmission, NOTIFICATION-TYPE FROM SNMPv2-SMI -- RFC2578 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC2580 TEXTUAL-CONVENTION, RowPointer FROM SNMPv2-TC -- RFC2579 IANAGmplsLSPEncodingTypeTC, IANAGmplsSwitchingTypeTC FROM IANA-GMPLS-TC-MIB -- RFC4802 InetAddress, InetAddressType FROM INET-ADDRESS-MIB -- RFC4001 Float32TC T. Otani et al. Expires Oct. 2012 [Page 6] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 FROM FLOAT-TC-MIB -- RFC6340 ; tedMIB MODULE-IDENTITY LAST-UPDATED "201205070000Z" -- 7 May 2012 00:00:00 GMT ORGANIZATION "IETF CCAMP Working Group." CONTACT-INFO " Tomohiro Otani otani@kddilabs.jp Masanori Miyazawa ma-miyazawa@kddilabs.jp Thomas D. Nadeau tnadeau@lucidvision.com Kenji Kumaki ke-kumaki@kddilabs.jp Comments and discussion to ccamp@ietf.org" DESCRIPTION "This MIB contains managed object definitions for TED in support of MPLS/GMPLS TE Database. Copyright (C) 2011 The IETF Trust. This version of this MIB module is part of RFC xxx; see the RFC itself for full legal notices." -- Revision history. REVISION "201205070000Z" -- 7 May 2012 00:00:00 GMT DESCRIPTION "Initial version. Published as RFC xxx." -- RFC-editor pls fill in yyy ::= { transmission yyy } -- assigned by IANA, see section 9.1 for details -- Textual Conventions. TedAreaIdTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The area identifier of the IGP. If OSPF is used to advertise LSA, this represents an ospfArea. If ISIS is used, this represents an area address." SYNTAX OCTET STRING (SIZE (0..20)) TedRouterIdTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION " The router identifier. If OSPF is used to advertise LSA, this represents a Router ID. If ISIS is used, this represents a System ID." SYNTAX OCTET STRING (SIZE (0..6)) T. Otani et al. Expires Oct. 2012 [Page 7] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 TedLinkIndexTC ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION " The link identifier. If OSPF is used, this represents an ospfLsdbID. If ISIS is used, this represents an isisLSPID. If a locally configured link is used, this object represents an arbitrary value which is locally defined in a router" SYNTAX OCTET STRING (SIZE (0..8)) -- Top level components of this MIB. tedNotifications OBJECT IDENTIFIER ::= { tedMIB 0 } tedObjects OBJECT IDENTIFIER ::= { tedMIB 1 } tedConformance OBJECT IDENTIFIER ::= { tedMIB 2 } -- -- TED Table -- tedTable OBJECT-TYPE SYNTAX SEQUENCE OF TedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table indicates multiple TED information which has been supported by [RFC3630]." ::= { tedObjects 1 } tedEntry OBJECT-TYPE SYNTAX TedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains TED information commonly utilized in both MPLS and GMPLS." INDEX { tedLocalRouterId, tedRemoteRouterId, tedLinkInformationSource, tedLinkIndex } ::= { tedTable 1 } TedEntry ::= SEQUENCE { tedLinkInformationSource INTEGER, tedLocalRouterId TedRouterIdTC, tedRemoteRouterId TedRouterIdTC, tedLinkIndex TedLinkIndexTC, tedLinkInformationData RowPointer, tedLinkState INTEGER, tedAreaId TedAreaIdTC, tedLinkType INTEGER, tedRouterIdAddrType InetAddressType, tedRouterIdAddr InetAddress, tedLinkIdAddrType InetAddressType, tedLinkIdAddr InetAddress, tedMetric Integer32, T. Otani et al. Expires Oct. 2012 [Page 8] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 tedMaxBandwidth Float32TC, tedMaxReservableBandwidth Float32TC, tedUnreservedBandwidthPri0 Float32TC, tedUnreservedBandwidthPri1 Float32TC, tedUnreservedBandwidthPri2 Float32TC, tedUnreservedBandwidthPri3 Float32TC, tedUnreservedBandwidthPri4 Float32TC, tedUnreservedBandwidthPri5 Float32TC, tedUnreservedBandwidthPri6 Float32TC, tedUnreservedBandwidthPri7 Float32TC, tedAdministrativeGroup Integer32, tedLocalId Integer32, tedRemoteId Integer32, tedLinkProtectionType BITS } tedLinkInformationSource OBJECT-TYPE SYNTAX INTEGER { unknown(0), locallyConfigured(1), ospfv2(2), ospfv3(3), isis(4), other(5) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the source of the information about the TE link." ::= { tedEntry 1 } tedLocalRouterId OBJECT-TYPE SYNTAX TedRouterIdTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object represents the router ID of the router originating the LSA. If OSPF is used to advertise LSA, this represents a Router ID. If ISIS is used, this represents a System ID. Otherwise, this represents zero." REFERENCE " OSPF Version 2, [RFC2328], C.1 OSPF for IPv6, [RFC5340], C.1 [ISO10589], Section 7.1 " ::= { tedEntry 2 } tedRemoteRouterId OBJECT-TYPE SYNTAX TedRouterIdTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the router at the remote end of the link from the originating router. If OSPF is used to advertise LSA, this T. Otani et al. Expires Oct. 2012 [Page 9] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 represents a Link ID in the Link TLV. If ISIS is used, this represents a neighbor system ID defined in [RFC5305]. Otherwise, this represents zero." REFERENCE " OSPF Version 2, [RFC2328], C.1 OSPF for IPv6, [RFC5340], C.1 [ISO10589], Section 7.1 IS-IS extensions for TE [RFC5305], C.3" ::= { tedEntry 3 } tedLinkIndex OBJECT-TYPE SYNTAX TedLinkIndexTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the link state identifier. If OSPF is used, this represents an ospfLsdbID. If ISIS is used, this represents an isisLSPID. Otherwise, this represents a unique identifier within a node." REFERENCE "OSPF Version 2, [RFC2328], A.4.1, OSPF for IPv6, [RFC5340], A.4.2 [ISO10589], Section 9.8 " ::= { tedEntry 4 } tedLinkInformationData OBJECT-TYPE SYNTAX RowPointer MAX-ACCESS read-only STATUS current DESCRIPTION "This object cross-references the source of the information about this TE link and should be interpretted in the context of tedLinkInformationSource. If tedLinkInformationSource has the value unknown(0), this object SHOULD contain a value of zeroDotZero. If tedLinkInformationSource has the value locallyConfigured(1), this object MAY contain the identifier of the corresponding row entry in the teLinkTable of TE-LINK-STD- MIB[RFC4220], the identifier of the corresponding row in a local proprietary TE link MIB module, or the value of zeroDotZero otherwise. If tedLinkInformationSource has the value ospfv2(2)and ospfv3(3), this object MAY contain the identifier of the corresponding row entry in the ospfLocalLsdbTable of OSPFv2- MIB[RFC4750] and the ospfv3AreaLsdbTable of OSPFv3-MIB[RFC5643], or the value of zeroDotZero otherwise. If tedLinkInformationSource has the value isis(4) this object MAY contain the identifier of the corresponding row entry in the isisAreaAddr of ISIS-MIB [RFC4444], or the value of zeroDotZero otherwise. If tedLinkInformationSource has the value other(5) this object MAY contain the identifier of the corresponding row entry a local proprietary MIB module, or the value of zeroDotZero otherwise." T. Otani et al. Expires Oct. 2012 [Page 10] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 ::= { tedEntry 5 } tedLinkState OBJECT-TYPE SYNTAX INTEGER { unknown (0), up (1), down (2) } MAX-ACCESS read-only STATUS current DESCRIPTION " This object represents the actual operational state of this TE link. For instance, if a row is created in the tedTable, but the actual TE link is not available for some reason (e.g. when there is not yet physical link or manually disable), then the object would be down(2) state. In contrast, if a row is added and the TE link is available, this would be operationally up(1)." ::= { tedEntry 6 } tedAreaId OBJECT-TYPE SYNTAX TedAreaIdTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the area identifier of the IGP. If OSPF is used to advertise LSA, this represents an ospfArea. If ISIS is used, this represents an area address. Otherwise, this represents zero." REFERENCE " OSPF Version 2, [RFC2328], C.2 OSPF for IPv6, [RFC5340], C.2 [ISO10589], Section 9.8 " ::= { tedEntry 7 } tedLinkType OBJECT-TYPE SYNTAX INTEGER { pointToPoint (1), multiAccess (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the type of the link such as point-to-point or multi-access." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.1" ::= { tedEntry 8 } tedRouterIdAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION T. Otani et al. Expires Oct. 2012 [Page 11] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 " This object indicates the TE-Router ID address type. Only values unknown(0), ipv4(1) or ipv6(2) must be supported. " ::= { tedEntry 9 } tedRouterIdAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the TE-Router ID." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, RFC 3630, 2.4.1" ::= { tedEntry 10 } tedLinkIdAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION " This object indicates the address type of the TE Link ID. Only values unknown(0), ipv4(1) or ipv6(2) must be supported." ::= { tedEntry 11 } tedLinkIdAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Router ID of the neighbor in the case of point-to-point links. This also indicates the interface address of the designated router in the case of multi-access links." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.2" ::= { tedEntry 12 } tedMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the traffic engineering metric value of the TE link." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.5" ::= { tedEntry 13 } tedMaxBandwidth OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current T. Otani et al. Expires Oct. 2012 [Page 12] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 DESCRIPTION "This indicates the maximum bandwidth that can be used on this link in this direction." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.6" ::= { tedEntry 14 } tedMaxReservableBandwidth OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the maximum bandwidth that may be reserved on this link in this direction." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.7" ::= { tedEntry 15 } tedUnreservedBandwidthPri0 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 0." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 16 } tedUnreservedBandwidthPri1 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 1." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 17 } tedUnreservedBandwidthPri2 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION T. Otani et al. Expires Oct. 2012 [Page 13] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 "This indicates the amount of bandwidth not yet reserved at the priority 2." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 18 } tedUnreservedBandwidthPri3 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 3." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 19 } tedUnreservedBandwidthPri4 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 4." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 20 } tedUnreservedBandwidthPri5 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 5." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 21 } tedUnreservedBandwidthPri6 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 6." T. Otani et al. Expires Oct. 2012 [Page 14] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 22 } tedUnreservedBandwidthPri7 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the amount of bandwidth not yet reserved at the priority 7." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.8" ::= { tedEntry 23 } tedAdministrativeGroup OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Administrative Group which the link belong to. Since the value is a bit mask, the link can belong to multiple groups. This is also called Resource Class/Color." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.9" ::= { tedEntry 24 } tedLocalId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Link local identifier of an unnumbered link." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.1" ::= { tedEntry 25 } tedRemoteId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the Link remote identifier of an unnumbered link." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.1" ::= { tedEntry 26 } tedLinkProtectionType OBJECT-TYPE T. Otani et al. Expires Oct. 2012 [Page 15] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 SYNTAX BITS { extraTraffic(0), unprotected(1), shared (2), dedicatedOneToOne (3), dedicatedOnePlusOne(4), enhanced(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the protection type of the TE link." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.2" ::= { tedEntry 27 } -- -- TED Local Interface IP Address Table -- tedLocalIfAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF TedLocalIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the IP address information of a local TE link." ::= { tedObjects 2 } tedLocalIfAddrEntry OBJECT-TYPE SYNTAX TedLocalIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains the IP address information of the local TE link." INDEX { tedLinkIndex, tedLocalIfAddr } ::= { tedLocalIfAddrTable 1 } TedLocalIfAddrEntry ::= SEQUENCE { tedLocalIfAddrType InetAddressType, tedLocalIfAddr InetAddress } tedLocalIfAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the address type of the local TE link. Only values unknown(0), ipv4(1) or ipv6(2) have to be supported." ::= { tedLocalIfAddrEntry 1 } T. Otani et al. Expires Oct. 2012 [Page 16] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 tedLocalIfAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object indicates the address of the local TE link." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.3, Traffic Engineering Extensions to OSPF Version3, RFC5329, 4.3" ::= { tedLocalIfAddrEntry 2 } -- -- TED Remote Interface IP Address Table -- tedRemoteIfAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF TedRemoteIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the IP address information of a remote TE link." ::= { tedObjects 3 } tedRemoteIfAddrEntry OBJECT-TYPE SYNTAX TedRemoteIfAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry contains the IP address information of the remote TE link." INDEX { tedLinkIndex, tedRemoteIfAddr } ::= { tedRemoteIfAddrTable 1 } TedRemoteIfAddrEntry ::= SEQUENCE { tedRemoteIfAddrType InetAddressType, tedRemoteIfAddr InetAddress } tedRemoteIfAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the address type of the remote TE link." ::= { tedRemoteIfAddrEntry 1 } tedRemoteIfAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current T. Otani et al. Expires Oct. 2012 [Page 17] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 DESCRIPTION "This object indicates the address of the remote TE link." REFERENCE " Traffic Engineering (TE) Extensions to OSPF Version 2, [RFC 3630], 2.5.4, Traffic Engineering Extensions to OSPF Version3, [RFC5329], 4.4" ::= { tedRemoteIfAddrEntry 2 } -- -- TED Switching Capability Table -- tedSwCapTable OBJECT-TYPE SYNTAX SEQUENCE OF TedSwCapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the GMPLS TED switching capability information." ::= { tedObjects 4 } tedSwCapEntry OBJECT-TYPE SYNTAX TedSwCapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry relates each TE link with its GMPLS TE switching capability information. IF the MIB deals with only OSPF-TE information, the value of each object related with GMPLS TE extensions should be null." INDEX { tedLinkIndex, tedSwCapIndex } ::= { tedSwCapTable 1 } TedSwCapEntry ::= SEQUENCE { tedSwCapIndex Unsigned32, tedSwCapType IANAGmplsSwitchingTypeTC, tedSwCapEncoding IANAGmplsLSPEncodingTypeTC, tedSwCapMaxLspBandwidthPri0 Float32TC, tedSwCapMaxLspBandwidthPri1 Float32TC, tedSwCapMaxLspBandwidthPri2 Float32TC, tedSwCapMaxLspBandwidthPri3 Float32TC, tedSwCapMaxLspBandwidthPri4 Float32TC, tedSwCapMaxLspBandwidthPri5 Float32TC, tedSwCapMaxLspBandwidthPri6 Float32TC, tedSwCapMaxLspBandwidthPri7 Float32TC, tedSwCapMinLspBandwidth Float32TC, tedSwCapIfMtu Integer32, tedSwCapIndication INTEGER } tedSwCapIndex OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible T. Otani et al. Expires Oct. 2012 [Page 18] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 STATUS current DESCRIPTION "This index is utilized to identify multiple switching functions on a local or remote TE link according to definitions of textual conventions of GMPLS [RFC4801]." ::= { tedSwCapEntry 1 } tedSwCapType OBJECT-TYPE SYNTAX IANAGmplsSwitchingTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the GMPLS switching capability assigned to the TE link according to definitions of textual conventions of GMPLS [RFC4801]." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 2 } tedSwCapEncoding OBJECT-TYPE SYNTAX IANAGmplsLSPEncodingTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the GMPLS encoding type assigned to the TE link." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 3 } tedSwCapMaxLspBandwidthPri0 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 0 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 4 } tedSwCapMaxLspBandwidthPri1 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 1 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 5 } T. Otani et al. Expires Oct. 2012 [Page 19] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 tedSwCapMaxLspBandwidthPri2 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 2 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 6 } tedSwCapMaxLspBandwidthPri3 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 3 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 7 } tedSwCapMaxLspBandwidthPri4 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 4 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 8 } tedSwCapMaxLspBandwidthPri5 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 5 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 9 } tedSwCapMaxLspBandwidthPri6 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION T. Otani et al. Expires Oct. 2012 [Page 20] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 "This object indicates the maximum bandwidth of the TE link at the priority 6 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 10 } tedSwCapMaxLspBandwidthPri7 OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the maximum bandwidth of the TE link at the priority 7 for GMPLS LSP creation." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 11 } tedSwCapMinLspBandwidth OBJECT-TYPE SYNTAX Float32TC UNITS "Byte per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the minimum bandwidth of the TE link for GMPLS LSP creation if the switching capability field is TDM, PSC-1, PSC-2, PSC-3, or PSC-4." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 12 } tedSwCapIfMtu OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the MTU of the local or remote TE link." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 13 } tedSwCapIndication OBJECT-TYPE SYNTAX INTEGER { standard (0), arbitrary (1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates whether the interface supports Standard or Arbitrary SONET SDH." REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.4" ::= { tedSwCapEntry 14 } T. Otani et al. Expires Oct. 2012 [Page 21] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 -- -- TED SRLG Table -- tedSrlgTable OBJECT-TYPE SYNTAX SEQUENCE OF TedSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the SRLG information of the TE link." ::= { tedObjects 5 } tedSrlgEntry OBJECT-TYPE SYNTAX TedSrlgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entry relates each TE link with its SRLG information." INDEX { tedLinkIndex, tedSrlgIndex } ::= { tedSrlgTable 1 } TedSrlgEntry ::= SEQUENCE { tedSrlgIndex Unsigned32, tedSrlg Integer32 } tedSrlgIndex OBJECT-TYPE SYNTAX Unsigned32(1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION " This index is utilized to identify multiple SRLG values on a local or remote TE link. This object represents an arbitrary value which is locally defined in a router." REFERENCE " OSPF Extensions in support of GMPLS, [RFC4203], 1.3 " ::= { tedSrlgEntry 1 } tedSrlg OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicate the SRLG value assigned to a local or remote TE link" REFERENCE " OSPF Extensions in Support of GMPLS, [RFC4203], 1.3" ::= { tedSrlgEntry 2 } -- -- Notification Configuration -- T. Otani et al. Expires Oct. 2012 [Page 22] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 tedStatusChangeNotificationMaxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "A lot of notifications relating to the status change are expected to generate in a node, especially when a network failure occurs and might cause a performance degradation of the node itself. To avoid such a defect, this object provides the maximum number of notifications generated per minute. If events occur more rapidly, the implementation may simply fail to emit these notifications during that period, or may queue them until an appropriate time. A value of 0 means no throttling is applied and events may be notified at the rate at which they occur." DEFVAL {0} ::= { tedObjects 6 } tedCreatedDeletedNotificationMaxRate OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "A lot of notifications relating to new registration in ted table by receiving new TE link information or deletion of existing entries in ted table are expected to generate in a node. This object provides the maximum number of notifications generated per minute. " DEFVAL {0} ::= { tedObjects 7 } -- -- Notifications -- tedStatusChange NOTIFICATION-TYPE OBJECTS { tedLinkState } STATUS current DESCRIPTION "This notification signifies that there has been change in TE information of tedTable, tedLocalIfAddrTable, tedRemoteIfAddrTable, tedSwCapTable and/or tedSrlgTable. For example, this should be generated when tedUnreservedBandwidth is changed to create or delete LSP using registered TE link. " ::= { tedNotifications 1 } tedEntryCreated NOTIFICATION-TYPE OBJECTS { tedLinkState } STATUS current DESCRIPTION " This notification signifies that there has been new registration in ted table by receiving new TE link information. For T. Otani et al. Expires Oct. 2012 [Page 23] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 example, this should be generated when new index (tedLinkIndex) is registered in TED table." ::= { tedNotifications 2 } tedEntryDeleted NOTIFICATION-TYPE OBJECTS { tedLinkState } STATUS current DESCRIPTION "This notification signifies that there has been deletion of an entry in the ted table. For example, this should be generated when one of existing entries is deleted in TED table." ::= { tedNotifications 3 } -- Conformance Statement tedCompliances OBJECT IDENTIFIER ::= { tedConformance 1 } tedGroups OBJECT IDENTIFIER ::= { tedConformance 2 } -- Module Compliance tedModuleFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance statement for agents provides full support for the TED MIB." MODULE -- this module MANDATORY-GROUPS { tedMainGroup, tedObjectsGroup, tedNotificationGroup } GROUP tedUnnumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that supports the unnumbered links." GROUP tedNumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that supports the numbered links." GROUP tedSwCapGroup DESCRIPTION "This group is mandatory for TE links that supports GMPLS switching capability." GROUP tedSwCapMinLspBandwidthGroup DESCRIPTION "This group is mandatory for TE links if the switching capability field is TDM, PSC-1, PSC-2, PSC-3, or PSC-4." T. Otani et al. Expires Oct. 2012 [Page 24] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 GROUP tedSwCapIfMtuGroup DESCRIPTION "This group is mandatory for TE links that supports the MTU of the local or remote TE link." GROUP tedSwCapIndicationGroup DESCRIPTION "This group is mandatory for TE links that supports Standard or Arbitrary SONET/SDH." GROUP tedSrlgGroup DESCRIPTION "This group is mandatory for TE links that supports SRLG information." ::= { tedCompliances 1 } -- -- ReadOnly Compliance -- tedModuleReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "Compliance requirement for implementations only provide read- only support for TED. Such devices can then be monitored but cannot be configured using this MIB module." MODULE -- this module MANDATORY-GROUPS { tedMainGroup } GROUP tedUnnumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that supports the unnumbered links." GROUP tedNumberedLinkGroup DESCRIPTION "This group is mandatory for TE links that supports the numbered links." GROUP tedSwCapGroup DESCRIPTION "This group is mandatory for TE links that supports some GMPLS switching capabilities." GROUP tedSwCapMinLspBandwidthGroup DESCRIPTION "This group is mandatory for TE links if the switching capability field is TDM, PSC-1, PSC-2, PSC-3, or PSC-4." GROUP tedSwCapIfMtuGroup DESCRIPTION T. Otani et al. Expires Oct. 2012 [Page 25] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 "This group is mandatory for TE links that supports the MTU of the local or remote TE link." GROUP tedSwCapIndicationGroup DESCRIPTION "This group is mandatory for TE links that supports Standard or Arbitrary SONET/SDH." GROUP tedSrlgGroup DESCRIPTION "This group is mandatory for TE links that supports SRLG information." ::= { tedCompliances 2 } -- Units of conformance tedMainGroup OBJECT-GROUP OBJECTS { tedLinkState , tedAreaId , tedLinkType , tedRouterIdAddrType , tedRouterIdAddr , tedLinkIdAddrType , tedLinkIdAddr , tedMetric , tedMaxBandwidth , tedMaxReservableBandwidth , tedUnreservedBandwidthPri0 , tedUnreservedBandwidthPri1 , tedUnreservedBandwidthPri2 , tedUnreservedBandwidthPri3 , tedUnreservedBandwidthPri4 , tedUnreservedBandwidthPri5 , tedUnreservedBandwidthPri6 , tedUnreservedBandwidthPri7 , tedAdministrativeGroup , tedLinkProtectionType , tedLinkInformationData } STATUS current DESCRIPTION "Collection of objects for TED management" ::= { tedGroups 1 } tedObjectsGroup OBJECT-GROUP OBJECTS { tedStatusChangeNotificationMaxRate, tedCreatedDeletedNotificationMaxRate } STATUS current DESCRIPTION "This objects needed to implement notification." T. Otani et al. Expires Oct. 2012 [Page 26] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 ::= { tedGroups 2 } tedNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { tedStatusChange, tedEntryCreated, tedEntryDeleted } STATUS current DESCRIPTION " This group is mandatory for those implementations that can implement the notifications contained in this group. " ::= { tedGroups 3 } tedUnnumberedLinkGroup OBJECT-GROUP OBJECTS { tedLocalId, tedRemoteId } STATUS current DESCRIPTION "This objects needed to implement the unnumbered links." ::= { tedGroups 4 } tedNumberedLinkGroup OBJECT-GROUP OBJECTS { tedLocalIfAddrType, tedRemoteIfAddrType } STATUS current DESCRIPTION "This objects needed to implement the numbered links." ::= { tedGroups 5 } tedSwCapGroup OBJECT-GROUP OBJECTS { tedSwCapType, tedSwCapEncoding, tedSwCapMaxLspBandwidthPri0, tedSwCapMaxLspBandwidthPri1, tedSwCapMaxLspBandwidthPri2, tedSwCapMaxLspBandwidthPri3, tedSwCapMaxLspBandwidthPri4, tedSwCapMaxLspBandwidthPri5, tedSwCapMaxLspBandwidthPri6, tedSwCapMaxLspBandwidthPri7 } STATUS current DESCRIPTION "This objects needed to implement TE links with its GMPLS TE switching capability information." ::= { tedGroups 6 } tedSwCapMinLspBandwidthGroup OBJECT-GROUP T. Otani et al. Expires Oct. 2012 [Page 27] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 OBJECTS { tedSwCapMinLspBandwidth } STATUS current DESCRIPTION "This objects needed to implement the minimum bandwidth of the TE link for GMPLS LSP creation." ::= { tedGroups 7 } tedSwCapIfMtuGroup OBJECT-GROUP OBJECTS { tedSwCapIfMtu } STATUS current DESCRIPTION "This objects needed to implement the MTU information of the local or remote TE link." ::= { tedGroups 8 } tedSwCapIndicationGroup OBJECT-GROUP OBJECTS { tedSwCapIndication } STATUS current DESCRIPTION "This objects needed to implement the indication whether the interface supports Standard or Arbitrary SONET/SDH." ::= { tedGroups 9 } tedSrlgGroup OBJECT-GROUP OBJECTS { tedSrlg } STATUS current DESCRIPTION "This objects needed to implement multiple SRLG values with GMPLS TE information." ::= { tedGroups 10 } END 8. Security Consideration There is a number of management objects defined in this MIB module that has a MAX-ACCESS clause of read-write. Such objects may be considered sensitive or vulnerable in some network environments. The support for SET operations in a non-secure environment without proper protection can have a negative effect on network operations. Some of the readable objects in this MIB module (i.e., objects with a MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly T. Otani et al. Expires Oct. 2012 [Page 28] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: tedTable, tedLocalIfAddrTable, tedRemoteIfAddrTable, tedSwCapTable and tedSrlgTable contain topology information for the MPLS/GMPLS network. If an administrator does not want to reveal this information, then these tables should be considered sensitive/vulnerable. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full supports for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principles (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 9. IANA Considerations The following "IANA Considerations" subsection requests IANA for a new assignment under the transmission subtree. New assignments can only be made via a Standards Action as specified in [RFC5226]. 9.1 IANA Considerations for TED-MIB The IANA is requested to assign {transmission XXX } to the TED-MIB module specified in this document. 10. References 10.1 Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2328] J. Moy, " OSPF version2 ", RFC2328, April 1998. [RFC2578] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. T. Otani et al. Expires Oct. 2012 [Page 29] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 [RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC4001] M. Daniele, B. Haberman, S. Routhier, J. Schoenwaelder, "Textual Conventions for Internet Network Addresses", RFC4001, Feb. 2005. [RFC3630] D. Katz, et al, "Traffic Engineering (TE) Extensions to OSPF Version2", RFC3630, Sep. 2003. [RFC4203] K. Kompella, and Y. Rekhter, "OSPF Extensions in Support of Generalized Multi-Protocol Label Switching", RFC4203, Oct. 2005. [RFC4750] Dan Joyal, et al, "OSPF Version 2 Management Information Base", RFC4750, Dec. 2006. [RFC4801] T. Nadeau and A. Farrel, Ed., "Definitions of Textual Conventions for Generalized Multiprotocol Label Switching (GMPLS) Management", RFC4801, Feb. 2007. [RFC5329] K. Ishiguro, V. Manral, A. Davey, A.Lindem " Traffic Engineering Extensions to OSPF Version 3 ", RFC5329, Sep. 2008. [RFC5340] R. Coltun, D. Ferguson, J. Moy, A.Lindem " OSPF for IPv6", RFC5340, July 2008. [RFC5643] Dan Joyal, et al, "Management Information Base for OSPFv3 ", RFC5643, August 2009. [RFC6340] R. Presuhn, "Textual Conventions for the Representation of Floating-point Number ", RFC6340, August 2011. [ISO10589] ISO 10589, "Intermediate system to Intermediate system routeing information exchange protocol for use in conjunction with the Protocol for providing the Connectionless-mode Network Service (ISO 8473)", ISO/IEC 10589:2002. 10.2 Informative References [RFC3410] J. Case, R. Mundy, D. pertain, B.Stewart, "Introduction and Applicability Statement for Internet Standard Management Framework", RFC 3410, Dec. 2002. [RFC3812] Srinivasan, C., Viswanathan, A., and T. Nadeau, "Multiprotocol Label Switching (MPLS) Traffic Engineering T. Otani et al. Expires Oct. 2012 [Page 30] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 (TE) Management Information Base (MIB)", RFC 3812, June 2004. [RFC3813] Srinivasan, C., Viswanathan, A., and T. Nadeau, "Multiprotocol Label Switching (MPLS) Label Switching (LSR) Router Management Information Base (MIB)", RFC 3813, June 2004. [RFC3945] E. Mannie, "Generalized Multi-Procol Label Switching (MPLS) Architecture", RFC3945, Oct. 2004. [RFC4202] K. Kompella, and Y. Rekhter, "Routing Extensions in Support of Generalized Multi-Protocol Label Switching", RFC4202, Oct. 2005. [RFC4220] M. Dubuc, T. D. Nadeu and J. Lang, " Traffic Engineering Link Management Information Base ", RFC4220, Dec. 2005. [RFC4377] T. Nadeau, et al, "Operations and Management (OAM) Requirements for Multi-Protocol Label Switched (MPLS) Networks", RFC 4377, February 2006. [RFC4444] T. Parker, et al, "Management Information Base for Intermediate System to Intermediate System (IS-IS)", RFC 4444, April 2006. [RFC4802] T. D. Nadeu and A. Farrel, "Generalized Multiprotocol Label Switching (GMPLS) Traffic Engineering Management Information Base", RFC4802, Feb. 2007. [RFC4803] T. D. Nadeu and A. Farrel, "Generalized Multiprotocol Label Switching (GMPLS) Label Switching Router (LSR) Management Information Base", RFC4803, Feb., 2007. [RFC5305] H. Smit and T. Li, "IS-IS extensions for Traffic Engineering", RFC 5305, Oct. 2008. [RFC5307] K. Kompella, and Y. Rekhter, "IS-IS Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)", RFC5307, Oct. 2008. [RFC5226] Narten, T. and H. Alvestrand., " Guidelines for Writing an IANA Considerations Section in RFCs" BCP 26, RFC 5226, May 2008. 11. Acknowledgment The authors wish to acknowledge and thank the following individuals for their valuable comments to this document: Ken Nagami, Shuichi Okamoto, Adrian Farrel, Diego Caviglia and Acee Lindem. T. Otani et al. Expires Oct. 2012 [Page 31] draft-ietf-ccamp-gmpls-ted-mib-13.txt May 2012 12. Authors' Addresses Tomohiro Otani KDDI Corporation KDDI Bldg, 2-3-2, Nishishinjuku, Shinjuku-ku, Tokyo, 163-8003, Japan Email: tm-otani@kddi.com Masanori Miyazawa KDDI R&D Laboratories, Inc. 2-1-15 Ohara Fujimino, Saitama, 356-8502, Japan. Email: ma-miyazawa@kddilabs.jp Thomas D. Nadeau Email: tnadeau@lucidvision.com Kenji Kumaki KDDI Corporation Garden Air Tower Iidabashi, Chyoda-ku, Tokyo, 102-8460, Japan Email: ke-kumaki@kddi.com T. Otani et al. Expires Oct. 2012 [Page 32]