Definitions of Supplemental Managed Objects for ATM Management June 1995 | Faye Ly (editor) BayNetworks Communications, Inc. faye@Baynetworks.COM Michael Noto (editor) Bell Communications Research noto@cc.bellcore.com Andrew Smith (editor) BayNetworks Communications, Inc. asmith@Baynetworks.COM Kaj Tesink (editor) Bell Communications Research kaj@cc.bellcore.com 1. Status of this Memo This document is an Internet Draft. Internet Drafts are working documents of the Internet Engineering Task Force (IETF), its Areas, and its Working Groups. Note that other groups may also distribute working documents as Internet Drafts. Internet Drafts are valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet Drafts as reference material or to cite them other than as a "work in progress". draft Supplemental ATM Management Objects June 1995 2. Introduction This memo defines an experimental portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes objects used for managing ATM-based interfaces, devices, networks and services in addition to those defined in the ATM MIB [1], to provide additional support for the management of: - ATM Switched Virtual Connections (SVCs) - ATM Permanent Virtual Connections (PVCs) This memo specifies a MIB module in a manner that is both compliant to the SNMPv2 SMI, and semantically identical to the peer SNMPv1 definitions. This memo does not specify a standard for the Internet community. 3. The SNMPv2 Network Management Framework The SNMPv2 Network Management Framework consists of four major components. They are: 0 RFC 1442 [2] which defines the SMI, the mechanisms used for describing and naming objects for the purpose of management. 0 STD 17, RFC 1213 [3] defines MIB-II, the core set of managed objects for the Internet suite of protocols. 0 RFC 1445 [4] which defines the administrative and other architectural aspects of the framework. 0 RFC 1448 [5] which defines the protocol used for network access to managed objects. The Framework permits new objects to be defined for the purpose of experimentation and evaluation. Expires in six months [Page 2] draft Supplemental ATM Management Objects June 1995 4. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type. 5. Overview The purpose of this memo is to provide additional capabilities, not found in the ATM MIB [1], which are needed to manage ATM interfaces. This memo addresses the following areas: - ATM Switch/Network/Host Support - ATM Switch/Network Support - ATM Host Support 5.1. Background In addition to the MIB module defined in this memo, other MIB modules are necessary to manage ATM interfaces, links and cross-connects. Examples include MIB II for general system and interface management (RFC 1213 and RFC 1573), the DS3 or SONET MIBs for management of SONET and DS3 physical interfaces, and, as appropriate, MIB modules for applications that make use of ATM, such as SMDS [15] and LAN Emulation [14]. These MIB modules are outside the scope of this specification. This MIB module also requires the use of the ATM MIB module defined in [1]. ATM Endpoint applications such as ATM LAN Emulation or Classical IP-over-ATM Clients and Servers use ATM to establish SVC/PVC connections for exchanging control and data information. The agents of these ATM applications must provide Expires XX [Page 3] draft Supplemental ATM Management Objects June 1995 the network manager with information on the SVC/PVCs in use and which applications are using them. The information can be made generic so as to apply to all ATM applications. This memo proposes extensions to the ATM MIB [1] in order to support this. The current specification of this supplemental ATM MIB is based on SNMPv2. 5.2. Supported Functions The managed ATM objects are arranged into the following groups: I. ATM Switch/Network/Host Support: (1) ATM Switch/Network/Host Group atmVclStatTable atmVplStatTable + (2) ATM Switch/Network/Host SVC Group atmSvcTable (partially) II. ATM Switch/Network Support: (3) ATM Switch/Network Group atmIfAdminAddrTable (4) ATM Switch/Network SVC Group atmSvcTable (partially) III. ATM Host Support: (5) ATM Host Group atmVclExtTable atmVclAddressTable | atmAddrVclTable | (6) ATM Host Signalling Group | atmSigDescrParamTable IV. Signalling-over-VPC Support: | (7) ATM VP Interface Configuration Group atmVplIfConfTable 5.2.1. ATM Switch/Network/Host Support 5.2.1.1. ATM Switch/Network/Host Group 5.2.1.1.1. ATM VCL Statistics Table The atmVclStatTable contains counters such as the cells | received and cells transmitted per VCL (SVC or PVC). These | Expires XX [Page 4] draft Supplemental ATM Management Objects June 1995 counters are defined as 32 bit integers. The implementation | of this table is optional. 5.2.1.1.2. ATM VPL Statistics Table The atmVplStatTable contains counters such as the cells + received and cells transmitted per VPL (SVC or PVC). These + counters are defined as 32 bit integers. The implementation + of this table is optional. + 5.2.1.2. ATM Switch/Network/Host SVC Group All objects in this Group are listed in the atmSvcTable. This table also contains objects of the ATM Switch/Network SVC Group. 5.2.1.2.1. ATM Interface SVC Configuration This group contains information on the configuration of local | ATM interfaces on an ATM device required to support SVCs in | addition to those defined in the atmInterfaceConfTable of the | ATM MIB [1] and those defined in RFC1573 [6]. This group | includes the signalling entity role and the signalling type. | The signalling entity role object defines whether a signalling | entity has the role of user, network, or a symmetric entity. | The signalling type defines the type of signalling supported | at the local ATM interface (e.g., ITU-T DSS2 signalling). The | defined signalling types supported by this MIB include: ITU-T | DSS2 [11], ATM Forum's UNI 3.1 [10], and ATM Forum's P-NNI | [12]. | 5.2.1.2.2. SSCOP - This group contains information on the ATM SSCOP signalling layer and must be supported by signalling entities. 5.2.1.2.3. Unsupported Service Failures This group contains information on the setup failures that occur when setting up an ATM SVC. Maintaining counters for each individual signalling cause codes would result in a large number of counters. Instead, this memo uses an approach that lumps events into three categories. Three counters are used to monitor connection failures occurring due to: 1) Expires XX [Page 5] draft Supplemental ATM Management Objects June 1995 unavailable route, 2) unavailable switch or network resources, or 3) the called party. The counters are defined as follows: 1. Route Unavailable Counter This counter maintains the number of calls cleared because there was no route unavailable to the destination. 2. Resources Unavailable Counter This counter maintains the number of cleared calls due to switch or network resources being unavailable. 3. Called Party Counter This counter maintains the number of cleared calls caused by the called party (e.g., called party rejects the call). 5.2.1.2.4. ATM Signalling Layer Protocol Errors This group contains information on the Protocol Errors that occur at the signalling layer when establishing an ATM SVC. 5.2.1.2.5. UNI Signalling Sub-layer Statistics Configuration information is needed per signalling entity in | order to manage attributes of all SVCs set up by that entity. | Since signalling entities are not always bound one to one to | ATM UNIs, a more flexible indexing mechanism would be to allow | multiple signalling entities on a single UNI or vice versa - | using ifIndex and VPI would provide sufficient flexibility | here. | Statistics per VCL are needed in order to find out the usage of VCL resources by ATM applications. Additionally, to | monitor the usage and health of a UNI signalling | entity, some counters are needed per UNI signalling entity. | Two new objects are added to count the number of connections | established. One for incoming SVCs and one for outgoing SVCs. | Expires XX [Page 6] draft Supplemental ATM Management Objects June 1995 5.2.1.2.6. Indexing of the atmSvcTable -- Text To Be Provided 5.2.2. ATM Switch/Network Support 5.2.2.1. ATM Switch/Network Group 5.2.2.1.1. ATM Interface Administrative Address Table This group is only supported by switches or networks for | interfaces that have multiple associated addresses. This | group contains an ATM Interface Administrative Address Table | (atmIfAdminAddrTable) which lists valid addresses for calls to | and from a given interface. One of these numbers shall be | specified as the "default" number. | 5.2.2.2. ATM Switch/Network SVC Group All objects in this Group are listed in the atmSvcTable. This table also contains objects of the ATM Switch/Network/Host SVC Group. 5.2.2.2.1. ATM UNI SVC Information Element Support A number of Information Elements may or may not be supported | by ATM switches or Networks. Hence, for trouble isolation it | is important to keep track which particular Information | Elements are supported. The corresponding group of objects | must be supported by switches or networks supporting SVCs, and | indicate whether the following Information Elements are | enabled/disabled: | 1) Calling party number - 2) Calling party subaddress | 3) Called party subaddress + 4) Broadband high layer information + 5) Broadband low layer information + 6) Broadband repeat indicator + Expires XX [Page 7] draft Supplemental ATM Management Objects June 1995 7) AAL parameters + The last parameter, Preferred Carrier Pre-Subscription, + identifies the carrier to which intercarrier calls originated + from this interface are routed when transit network selection + information is not provided by the calling party. + 5.2.3. ATM Host Support 5.2.3.1. ATM Host Group 5.2.3.1.1. VCL Extension Table There can be two types of VCLs used by ATM applications: a | Permanent VC or a Switched VC. The ATM MIB [1] provides | general connection management (atmVclTable). This memo | contains the atmVclExtTable, an extension to the atmVclTable, | which supports both SVC/PVC monitoring and SVC configuration | capabilities. | The object Connection Type specifies the type of the VCL as | either a PVC, an incoming SVC, or an outgoing SVC. | When creating an SVC, the agent can represent the VCL's attributes by selecting entries from two tables: the ATM Traffic Descriptor Parameter Table defined in the ATM MIB [1] and the ATM Signalling Descriptor Parameter Table defined in | this memo. For SVCs, the ATM VCL Signalling Descriptor Index | object is used to point to an entry in the ATM Signalling | Descriptor Parameter Table. | 5.2.3.1.2. ATM VPI/VCI to Address Mapping Table In the atmVclAddressTable, the objects ATM Local Address | (atmLocalAddr) and ATM Remote Address (atmRemoteAddr) | represent the two endpoint addresses of a VCL. ATM Local | Address identifies the local endpoint of the VCL represented | by this agent. While, the ATM Remote address represents the | address of the ATM application at the other end of the VCL. | The atmLocalAddrIndex allows an agent to uniquely identify a | single entry under a given Local ATM Address, esp. when there | are multiple VCLs. The atmRemoteAddrIndex is used in a | similar manner. | Expires XX [Page 8] draft Supplemental ATM Management Objects June 1995 5.2.3.1.3. ATM Address to VPI/VCI Mapping Table Some ATM applications (e.g. LAN Emulation) use ATM endpoint addresses even over PVCs. In order to trace SVC/PVCs between such ATM applications, it is important to be able to monitor VCLs (both SVCs and PVCs) indexed by their endpoint ATM | addresses. The atmAddrVclTable contains all VCCs currently | active and is indexed by the remote ATM address. It is the | reverse of the atmVclAddressTable. | 5.2.3.2. ATM Host SVC Group 5.2.3.2.1. Signalling Descriptor Parameter Table This table extends the ATM VCL table of the ATM MIB [1] to include all other necessary signalling information as specified in both ATM Forum UNI Specifications [9] and [10]. A user can create an entry with all signalling parameters and later use that entry to specify the signalling characteristics of SVCs. Signalling attributes can be grouped into following categories: 1) ATM Adaptation Layer Parameters Information in this group are captured in the ATM Signalling Descriptor Parameter Table defined in this memo. Please refer to section 5.4.5.5 of [9] and [10]. 2) Broadband Bearer Capability Information in this group are captured by the ATM Signalling Descriptor Parameter Table defined in this memo. Please refer to section 5.4.5.7 of [9] and [10]. 3) Broadband High Layer Information Information in this group are captured by the ATM Signalling Descriptor Parameter Table defined in this memo. Please refer to section 5.4.5.8 of [9] and [10]. 4) Broadband Low Layer Information Expires XX [Page 9] draft Supplemental ATM Management Objects June 1995 Information in this group are captured by the ATM Signalling Descriptor Parameter Table defined in this memo. Please refer to section 5.4.5.9 of [9] and [10]. 5.2.4. Signalling-over-VPC Support 5.2.4.1. ATM VP Interface Configuration -- Text to be provided -- 6. Valid Address Sets / Default Address A given ATM UNI interface may have an Address, "ifPhysAddress", to identify the interface. In addition, a given ATM UNI interface may have several other valid addresses which can be used to originate and receive calls. The valid addresses that are used to receive calls are listed in the "ifRcvAddrTable" defined in RFC1573 [6]. ATM interfaces of switches and networks do not use the ifRcvAddrTable. Valid addresses to be used by a switch or network are listed in the ATM Interface Administrative Address Table. The ATM Interface Administrative Address Table is not supported by hosts. 7. Configuration of VPLs, VCLs, and Cross-Connects The ATM Managed Objects needed to support the configuration of VPLs, VCLs, and Cross-Connects are defined in the ATM MIB [1]. Expires XX [Page 10] draft Supplemental ATM Management Objects June 1995 8. Definitions ATM2-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, | experimental, Counter32, Integer32, IpAddress FROM SNMPv2-SMI DisplayString, RowStatus | FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF atmMIBObjects, IfIndex, atmVclEntry, | atmVclVpi, atmVclVci, atmVplEntry, atmVplVpi | FROM ATM-MIB AtmSigDescrParamIndex, AtmAddr + FROM ATMTC-MIB + ifIndex FROM RFC1213-MIB; atm2MIB MODULE-IDENTITY LAST-UPDATED "9505011200Z" ORGANIZATION "IETF AToMMIB Working Group" CONTACT-INFO " Faye Ly Postal: Bay Networks Inc. 4401 Great America Parkway Santa Clara, CA 95052 US Tel: +1 408 764 1702 Fax: +1 408 988 5525 E-Mail: faye@Baynetworks.COM Michael Noto Postal: Bell Communications Research 331 Newman Springs Road Red Bank, NJ 07701 US Tel: +1 908 758 5104 Fax: +1 908 758 4177 E-mail: noto@cc.bellcore.com Andrew Smith Postal: Bay Networks Inc. Expires XX [Page 11] draft Supplemental ATM Management Objects June 1995 4401 Great America Parkway Santa Clara, CA 95052 US Tel: +1 408 764 1574 Fax: +1 408 988 5525 E-Mail: asmith@Baynetworks.COM Kaj Tesink Postal: Bell Communications Research 331 Newman Springs Road Red Bank, NJ 07701 US Tel: +1 908 758 5254 Fax: +1 908 758 4177 E-mail: kaj@cc.bellcore.com" DESCRIPTION "This MIB Module is a supplement to the ATM-MIB [1]. This MIB provides supplemental information from both a switch/network perspective and an ATM host/application prospective." ::= { experimental XX } atm2MIBObjects OBJECT IDENTIFIER ::= {atm2MIB 1} -- ******** NOTE TO THE RFC EDITOR ************** -- In case this module is put on the standards track -- replace the following: -- "atm2MIB MODULE-IDENTITY ::= {experimental XX}" with -- "atm2MIB MODULE-IDENTITY ::= {atmMIBObjects 13}" -- and include atmMIBObjects in the IMPORT clause. -- This ATM2-MIB Module consists of the following groups: -- ATM Switch/Network/Host Support: -- (1) ATM Switch/Network/Host Group -- atmVclStatTable -- atmVplStatTable + -- (2) ATM Switch/Network/Host SVC Group -- atmSvcTable (partially) -- ATM Switch/Network Support: -- (3) ATM Switch/Network Group -- atmIfAdminAddrTable -- (4) ATM Switch/Network SVC Group -- atmSvcTable (partially) Expires XX [Page 12] draft Supplemental ATM Management Objects June 1995 -- ATM Host Support: -- (5) ATM Host Group -- atmVclExtTable -- atmVclAddressTable | -- atmAddrVclTable | -- (6) ATM Host Signalling Group | -- atmSigDescrParamTable -- Signalling-over-VPC Support: + -- (7) ATM VP Interface Configuration Group -- atmVplIfConfTable Expires XX [Page 13] draft Supplemental ATM Management Objects June 1995 -- **************************************************** - -- (1) ATM Switch/Network/Host Group -- This group contains information for a Switch/Network/Host -- that implements ATM interfaces. This group contains -- the following table: -- 1. ATM VCL Statistics Table -- 2. ATM VPL Statistics Table + atmSwtchNetHostGroup OBJECT IDENTIFIER ::= { atm2MIBObjects 1} -- 1. ATM VCL Statistics Table atmVclStatTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmVclStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains all statistic counters per VCL. It is used to monitor the usage of | the VCL in terms of incoming cells and | outgoing cells." | ::= { atmSwtchNetHostGroup 1 } atmVclStatEntry OBJECT-TYPE SYNTAX AtmVclStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents a VCL." | INDEX { ifIndex, atmVclVpi, atmVclVci } ::= { atmVclStatTable 1 } AtmVclStatEntry ::= SEQUENCE { atmVclStatCellIns Counter32, atmVclStatCellOuts Counter32 } atmVclStatCellIns OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION Expires XX [Page 14] draft Supplemental ATM Management Objects June 1995 "The value of this object is the number of | cells received by this VCL since it was | established." | ::= { atmVclStatEntry 1 } atmVclStatCellOuts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object is the number of cells | transmitted from this VCL since it was | established." | ::= { atmVclStatEntry 2 } -- 2. ATM VPL Statistics Table + atmVplStatTable OBJECT-TYPE + SYNTAX SEQUENCE OF AtmVplStatEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "This table contains all statistic counters per + VPL. It is used to monitor the usage of the VPL + in terms of incoming cells and outgoing cells." + ::= { atmSwtchNetHostGroup 2 } + atmVplStatEntry OBJECT-TYPE + SYNTAX AtmVplStatEntry + MAX-ACCESS not-accessible + STATUS current + DESCRIPTION + "Each entry in this table represents a VPL." + INDEX { ifIndex, atmVplVpi } + ::= { atmVplStatTable 1 } + AtmVplStatEntry ::= + SEQUENCE { + atmVplStatCellIns Counter32, + atmVplStatCellOuts Counter32 + } + + atmVplStatCellIns OBJECT-TYPE + SYNTAX Counter32 + Expires XX [Page 15] draft Supplemental ATM Management Objects June 1995 MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of this object is the number of cells + received by this VPL since it was established." + ::= { atmVplStatEntry 1 } + atmVplStatCellOuts OBJECT-TYPE + SYNTAX Counter32 + MAX-ACCESS read-only + STATUS current + DESCRIPTION + "The value of this object is the number of cells + transmitted from this VPL since it was + established." + ::= { atmVplStatEntry 2 } + Expires XX [Page 16] draft Supplemental ATM Management Objects June 1995 -- **************************************************** -- (2) ATM Switch/Network/Host SVC Group -- This group contains information for a Switch/Network/Host -- that implements ATM interfaces supporting Switched -- Virtual Connections (SVCs). -- This group is located at the beginning of the following table:| -- 1. ATM SVC Table -- The remaining portion of this table consists of the -- (4) ATM Switch/Network SVC Group -- This group contains information for a Switch/Network -- that implements ATM interfaces supporting Switched -- Virtual Connections (SVCs). -- This group is located at the end of the following table: | -- 1. ATM SVC Table atmSwtchNetHostSVCGroup OBJECT IDENTIFIER::= { atm2MIBObjects 2} -- 1. ATM Interface SVC Configuration Table -- This table provides configuration for ATM -- Switched Virtual Connections (SVCs). atmSvcTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains ATM local interface configuration parameters, one entry per ATM signalling interface." | ::= { atmSwtchNetHostSVCGroup 1 } atmSvcEntry OBJECT-TYPE SYNTAX AtmSvcEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This list contains signalling configuration parameters and state variables." INDEX { ifIndex, atmSvcSigVpi } ::= { atmSvcTable 1} Expires XX [Page 17] draft Supplemental ATM Management Objects June 1995 AtmSvcEntry ::= SEQUENCE { -- ATM Switch/Network/Host SVC Group: atmSvcSigVpi INTEGER, atmSvcSigEntityRole INTEGER, atmSvcSigType INTEGER, atmSvcSSCOPConMontrs Counter32, - atmSvcSSCOPErrdPdus Counter32, atmSvcUnavailRoutes Counter32, atmSvcUnavailResrcs Counter32, atmSvcCldPrtyProblems Counter32, atmSvcSigMsgErrors Counter32, atmSvcSigTimerExpireds Counter32, atmSvcSigRestarts Counter32, atmSvcSigInEstabls Counter32, atmSvcSigOutEstabls Counter32, -- ATM Switch/Network SVC Group: atmSvcSupportClgPtyNumDel INTEGER, atmSvcSupportClgPtySubAddr INTEGER, atmSvcSupportCldPtySubAddr INTEGER, atmSvcSupportHiLyrInfo INTEGER, atmSvcSupportLoLyrInfo INTEGER, atmSvcSupportRepeatInd INTEGER, atmSvcSupportAALInfo INTEGER, atmSvcSupportPrefCarrier OCTET STRING } atmSvcSigVpi OBJECT-TYPE SYNTAX INTEGER (0..255) | MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VPI value used by this signalling entity." ::= { atmSvcEntry 1} - atmSvcSigEntityRole OBJECT-TYPE SYNTAX INTEGER { other(1), symmetric(2), user(3), network(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The role of this signalling entity." ::= { atmSvcEntry 2 } Expires XX [Page 18] draft Supplemental ATM Management Objects June 1995 atmSvcSigType OBJECT-TYPE SYNTAX INTEGER { other(1), iTUdss2(2), | aTMFuni3Dot0(3), | aTMFuni3Dot1(4), | aTMFuni4Dot0(5), | aTMFiisp(6), | aTMFpnni1Dot0(7) } | MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter identifies the type of signalling that will be used for the identified interface. ITU-T DSS2: | - Exact definition to be provided | ATM Forum UNI 3.0: | ATM Forum, ATM User-Network Interface, Version 3.0 (UNI 3.0) Specification, Part I (1994) [9]. ATM Forum UNI 3.1: | ATM Forum, ATM User-Network Interface, Version 3.1 (UNI 3.1) Specification, Part I (November 1994) [10]. ATM Forum UNI 4.0: | ATM Forum, ATM User-Network Interface, Version 4.0 (UNI 4.0) Specification, Part I (1995) [16]. ATM Forum IISP (formerly P-NNI v0) : | - Exact definition to be provided | ATM Forum P-NNI1.0 : | Private Network-to-Network Interface in ATM Forum 94-0471R4, P-NNI Draft Specification, P-NNI SWG (November 1994) [12]. NOTE: Update this reference when the draft matures" | ::= { atmSvcEntry 3} atmSvcSSCOPConMontrs OBJECT-TYPE - Expires XX [Page 19] draft Supplemental ATM Management Objects June 1995 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "SSCOP Connection Monitoring Counter. This counter counts the sum of the following errors: 1) SSCOP Connection Disconnect Counter The abnormal occurrence of this event is characterized by the expiry of Timer_NO_RESPONSE. (This event is communicated to the layer management with MAA-ERROR code P. See ITU-T Q.2110 [13].) | 2) SSCOP Connection Initiation Failure This condition indicates the inability to establish an SSCOP connection. This event occurs whenever the number of expiries of the connection control timer (Timer_CC) exceeds the MaxCC or upon receipt of a connection reject message BGREJ PDU. (This event is communicated to layer management with MAA-ERROR code O. See ITU-T Q.2110.) | 3) SSCOP Connection Re-Establ/Resynch This event occurs upon receipt of a BGN PDU or RESYNC PDU." ::= { atmSvcEntry 4} | atmSvcSSCOPErrdPdus OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "SSCOP Errored PDUs Counter. This counter counts the sum of the following errors: 1) Invalid PDUs. These are defined in SSCOP and consist of PDUs with incorrect length (MAA-ERROR code U), undefined PDU type code or not 32-bit aligned. 2) PDUs that result in MAA error codes and are discarded Expires XX [Page 20] draft Supplemental ATM Management Objects June 1995 See Errors A-M and Q-T defined in ITU-T Q.2110 [13]." | ::= { atmSvcEntry 5 } | atmSvcUnavailRoutes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Route Unavailable Counter. This counter counts the sum of the following errors: Cause Value Meaning 1 unallocated (unassigned) number 2 no route to specified transit network 3 no route to destination 88 incompatible destination" ::= { atmSvcEntry 6 } | atmSvcUnavailResrcs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Resource Unavailability Counter. This counter counts the sum of the following errors: Cause Value Meaning 27 destination out of order 35 requested VPCI/VCI not available 41 temporary failure 45 no VPCI/VCI available 47 resource unavailable, unspecified 49 Quality of Service unavailable 51 user cell rate not available 58 bearer capability not presently available 63 Service or option not available, unspecified 92 too many pending add party requests" ::= { atmSvcEntry 7 } | atmSvcCldPrtyProblems OBJECT-TYPE SYNTAX Counter32 Expires XX [Page 21] draft Supplemental ATM Management Objects June 1995 MAX-ACCESS read-only STATUS current DESCRIPTION "Called Party Responsible For Unsuccessful Call Counter. This counter counts the sum of the following errors: Cause Value Meaning 17 user busy 18 no user responding 21 call rejected 22 number changed 23 user rejects all calls with calling line id restriction (CLIR) 31 normal, unspecified Note: Cause Value #30 'response to STATUS ENQUIRY' was not included in this memo since it did not apply to a hard failure" ::= { atmSvcEntry 8 } | atmSvcSigMsgErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Incorrect Messages Counter. The Incorrect Messages Counter reflects any sort of incorrect information in a message. This includes: - RELEASE, RELEASE COMPLETE, ADD PARTY REJECT, DROP PARTY, and STATUS messages transmitted or received, that contain any of the Cause values listed below. - Ignored messages. These messages are dropped because the message was so damaged that it could not be further processed. A list of dropped messages is compiled below: 1. Message with invalid protocol discriminator 2. Message with errors in the call reference I.E. - Bits 5-8 of the first octet not equal to Expires XX [Page 22] draft Supplemental ATM Management Objects June 1995 '0000' - Bits 1-4 of the first octet indicating a length other than 3 octets - RELEASE COMPLETE message received with a call reference that does not relate to a call active or in progress - SETUP message received with call reference flag incorrectly set to 1 - SETUP message received with a call reference for a call that is already active or in progress. 3. Message too short The following cause values are monitored by this counter: Cause Value Meaning 10 VPCI/VCI unacceptable 28 invalid number format (address incomplete) 43 access information discarded 57 bearer capability not authorized 65 bearer capability not implemented 73 unsupported combination of traffic parameters 81 invalid call reference value 82 identified channel does not exist 89 invalid endpoint reference 91 invalid transit network selection 93 AAL parameters cannot be supported 96 mandatory information element is missing 97 message type non-existent or not implemented 99 information element non-existent or not implemented 100 invalid information element contents 101 message not compatible with call state 104 incorrect message length 111 protocol error, unspecified NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE Expires XX [Page 23] draft Supplemental ATM Management Objects June 1995 message and contain the same cause value, are redundant (for counting purposes) and should not be counted." ::= { atmSvcEntry 9 } | atmSvcSigTimerExpireds OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Timer Expiries Counter. The Timer Expiries Counter provides a count of network timer expiries, and to some extent, host or switch timer expiries. The conditions for incrementing this counter are: - Expiry of any network timer - Receipt of a RELEASE or RELEASE COMPLETE message with Cause #102, 'recovery on timer expiry'. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted." ::= { atmSvcEntry 10 } | atmSvcSigRestarts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Restart Activity Counter. The Restart Activity Counter provides a count of host, switch, or network restart activity. This counter is incremented when receiving or transmitting a RESTART message. NOTE: For this counter, RELEASE COMPLETE messages that are a reply to a previous RELEASE message and contain the same cause value, are redundant (for counting purposes) and should not be counted." ::= { atmSvcEntry 11 } | atmSvcSigInEstabls OBJECT-TYPE | Expires XX [Page 24] draft Supplemental ATM Management Objects June 1995 SYNTAX Counter32 | MAX-ACCESS read-only | STATUS current | DESCRIPTION | "Number of VCLs established at this signalling entity for incoming connections." ::= { atmSvcEntry 12 } | atmSvcSigOutEstabls OBJECT-TYPE | SYNTAX Counter32 | MAX-ACCESS read-only | STATUS current | DESCRIPTION | "Number of VCLs established at this signalling entity for outgoing connections." ::= { atmSvcEntry 13 } | atmSvcSupportClgPtyNumDel OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether the Calling Party Number | Information Element is transferred to the called party | address. The value of this object can be: | - enabled(1) This Information Element is transferred | to the called party | - disabled(2) This Information Element is NOT | transferred to the called party." | DEFVAL { disabled } ::= { atmSvcEntry 14 } | atmSvcSupportClgPtySubAddr OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether to accept and transfer | the Calling Party Subaddress Information Element from | the calling party to the called party. Calling party | subaddress information shall only be transferred to the | called party if calling party number delivery is | enabled (i.e., atmSvcSupportClgPtyNumDel = | 'enabled(1)'. The value of this object can be: | Expires XX [Page 25] draft Supplemental ATM Management Objects June 1995 - enabled(1) This Information Element is transferred | to the called party | - disabled(2) This Information Element is NOT | transferred to the called party." | DEFVAL { disabled } ::= { atmSvcEntry 15 } | atmSvcSupportCldPtySubAddr OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether to accept, transfer, and | deliver the Called Party Subaddress Information Element | from the calling party to the called party. The value | of this object can be: | - enabled(1) This Information Element is transferred | to the called party | - disabled(2) This Information Element is NOT | transferred to the called party." | DEFVAL { disabled } ::= { atmSvcEntry 16 } | atmSvcSupportHiLyrInfo OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether to accept, transfer, and | deliver the Broadband High Layer Information Element | from the calling party to the called party. The value | of this object can be: | - enabled(1) This Information Element is transferred | to the called party | - disabled(2) This Information Element is NOT | transferred to the called party." | DEFVAL { disabled } ::= { atmSvcEntry 17 } | atmSvcSupportLoLyrInfo OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write Expires XX [Page 26] draft Supplemental ATM Management Objects June 1995 STATUS current DESCRIPTION "This object indicates whether to accept, transfer, and | deliver the Broadband Low Layer Information Element | from the calling party to the called party. The value | of this object can be: | - enabled(1) This Information Element is transferred | to the called party | - disabled(2) This Information Element is NOT | transferred to the called party." | DEFVAL { disabled } ::= { atmSvcEntry 18 } | atmSvcSupportRepeatInd OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether to accept, transfer, and | deliver the Broadband Repeat Indicator with two or | three instances of the Broadband Low Layer Information | Element for low layer information selection from the | calling party to the called party. This object shall | only be transferred if atmSvcSupportLoLyrInfo = | 'enabled(1)'. The value of this object can be: | - enabled(1) This Information Element is transferred | to the called party | - disabled(2) This Information Element is NOT | transferred to the called party." | DEFVAL { disabled } ::= { atmSvcEntry 19 } | atmSvcSupportAALInfo OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object indicates whether to accept, transfer, and | deliver the ATM Adaptation Layer Parameters Information | Element from the calling party to the called party. | The value of this object can be: | - enabled(1) This Information Element is transferred | to the called party | Expires XX [Page 27] draft Supplemental ATM Management Objects June 1995 - disabled(2) This Information Element is NOT | transferred to the called party." | DEFVAL { disabled } ::= { atmSvcEntry 20 } | atmSvcSupportPrefCarrier OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter identifies the carrier to which intercarrier calls originated from this interface are routed when transit network selection information is not provided by the calling party. If a Carrier Identification Code (CIC) is used the parameter shall contain the CIC. For three-digit CICs, the first octet shall be '0' and the CIC is contained in the three following octets. If the preferred carrier feature is not supported the value is a zero-length string." ::= { atmSvcEntry 21 } | Expires XX [Page 28] draft Supplemental ATM Management Objects June 1995 -- **************************************************** -- (3) ATM Switch/Network Group -- This group contains information for a Switch/Network -- that implements ATM interfaces. This group contains -- the following table: -- 1. ATM Interface Administrative Address Table atmSwtchNetGroup OBJECT IDENTIFIER::= { atm2MIBObjects 3} -- 1. ATM Interface Administrative Address Table -- This table contains a list of the valid calling party -- addresses for a UNI in the case of both PVCs and SVCs. -- For PVCs, if addresses are not used then an entry in -- this table is not necessary. | atmIfAdminAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfAdminAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains an address list on a per interface basis. This table only applies to switches or networks and only for interfaces that have more than one address assigned." ::= { atmSwtchNetGroup 1 } atmIfAdminAddrEntry OBJECT-TYPE SYNTAX AtmIfAdminAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the atmIfAdminAddrTable." INDEX { ifIndex, atmIfAdminAddrAddress } ::= { atmIfAdminAddrTable 1} AtmIfAdminAddrEntry ::= SEQUENCE { atmIfAdminAddrAddress AtmAddr, | atmIfAdminAddrRowStatus RowStatus } atmIfAdminAddrAddress OBJECT-TYPE SYNTAX AtmAddr | MAX-ACCESS not-accessible Expires XX [Page 29] draft Supplemental ATM Management Objects June 1995 STATUS current DESCRIPTION "A valid address for a given switch or network interface." ::= { atmIfAdminAddrEntry 1} atmIfAdminAddrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to create and delete rows in the atmIfAdminAddrTable." ::= { atmIfAdminAddrEntry 2} Expires XX [Page 30] draft Supplemental ATM Management Objects June 1995 -- **************************************************** -- (5) ATM Host Group -- This group contains information for a Host -- that implements ATM interfaces. The following -- three tables are included in this group: | -- 1. ATM VCL Extension Table -- 2. ATM VPI/VCI to Address Mapping Table | -- 3. ATM Address to VPI/VCI Mapping Table | atmHostGroup OBJECT IDENTIFIER::= {atm2MIBObjects 4} -- 1. ATM VCL Extension Table atmVclExtTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmVclExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is an extension to the atmVclTable. It provides additional information necessary for VCLs management. Additional information included in this table are remote and local ATM addresses, the requested signalling interface number and the type of the VCL." ::= { atmHostGroup 1 } atmVclExtEntry OBJECT-TYPE SYNTAX AtmVclExtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents an extension to the atmVclTable. Objects atmVclConnType and atmVclSigDescrIndex are required during a creation of an entry in the atmVclTable." AUGMENTS { atmVclEntry } ::= { atmVclExtTable 1 } AtmVclExtEntry ::= SEQUENCE { atmVclConnType INTEGER, atmVclSigDescrIndex AtmSigDescrParamIndex } Expires XX [Page 31] draft Supplemental ATM Management Objects June 1995 atmVclConnType OBJECT-TYPE SYNTAX INTEGER { pvc(1), -- Permanent VC svcIncoming(2), -- Switched VC, incoming svcOutgoing(3) -- Switched VC, outgoing } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the VCL. Values for this object are | Permanent VC, incoming Switched VC, or outgoing | Switched VC. This object cannot be modified once | created." | ::= { atmVclExtEntry 1 } atmVclSigDescrIndex OBJECT-TYPE SYNTAX AtmSigDescrParamIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object identifies the row in | the ATM Signalling Descriptor Parameter Table | which | applies to this VCL." ::= { atmVclExtEntry 2 } -- 2. ATM VPI/VCI to Address Mapping Table | atmVclAddressTable OBJECT-TYPE | SYNTAX SEQUENCE OF AtmVclAddressEntry | MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides additional information | necessary for VCL management. Additional | information included in this table are remote and | local ATM addresses." | ::= { atmHostGroup 2 } atmVclAddressEntry OBJECT-TYPE | SYNTAX AtmVclAddressEntry | MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents additional | Expires XX [Page 32] draft Supplemental ATM Management Objects June 1995 information necessary for VCL management." | INDEX { ifIndex, atmVclVpi, atmVclVci, atmRemoteAddrIndex, atmLocalAddrIndex } | ::= { atmVclAddressTable 1 } | AtmVclAddressEntry ::= | SEQUENCE { atmRemoteAddrIndex INTEGER, atmRemoteAddr AtmAddr, | atmLocalAddrIndex INTEGER, | atmLocalAddr AtmAddr | } atmRemoteAddrIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) | MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is a number assigned by | an agent to uniquely identify a single entry under | a given Remote ATM Address. That is, there can be | multiple VCLs from a single Remote ATM address to | a Local ATM address on a given ATM interface, the | value of this object and atmLocalAddrIndex | uniquely identifies each of them." | ::= { atmVclAddressEntry 1 } | atmRemoteAddr OBJECT-TYPE SYNTAX AtmAddr | MAX-ACCESS read-create STATUS current DESCRIPTION "An ATM address on the remote end of the VCL. When not specified, the value of this object is a zero length string. For SVCs, the agent supplies the value of this object at creation time. For PVCs, manager can supply the value of this object during or after the PVC creation. Managers can modify the value of this object for PVC entries only." ::= { atmVclAddressEntry 2 } | atmLocalAddrIndex OBJECT-TYPE + SYNTAX INTEGER (1..65535) + MAX-ACCESS not-accessible + Expires XX [Page 33] draft Supplemental ATM Management Objects June 1995 STATUS current + DESCRIPTION + "The value of this object is a number assigned by + an agent to uniquely identify a single entry under + a given Local ATM Address. That is, there can be + multiple VCLs from a single Remote ATM address to + a Local ATM address on a given ATM interface, the + value of this object and atmRemoteAddrIndex + uniquely identifies each of them." + ::= { atmVclAddressEntry 3 } + atmLocalAddr OBJECT-TYPE SYNTAX AtmAddr | MAX-ACCESS read-create STATUS current DESCRIPTION "The ATM address on the local end of the VCL. When not specified, the value of this object is a zero length string. For SVCs, the agent supplies the value of this object at creation time. For PVCs, a manager can supply the value of this object during or after the PVC creation. Managers can modify the value of this object for PVC entries only." DEFVAL { ''H } ::= { atmVclAddressEntry 4 } | -- 3. ATM Address to VPI/VCI Mapping Table | -- This table provides an alternative way to access -- a row in the atmVclAddressTable by using | -- the remote address as an index, instead of | -- the ifIndex atmAddrVclTable OBJECT-TYPE | SYNTAX SEQUENCE OF AtmAddrVclEntry | MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides an alternative way to retrieve the atmVclTable. This table can be used to retrieve the indexing to the atmVclTable by the Remote ATM address." ::= { atmHostGroup 3 } | atmAddrVclEntry OBJECT-TYPE | Expires XX [Page 34] draft Supplemental ATM Management Objects June 1995 SYNTAX AtmAddrVclEntry | MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents an entry in | the atmVclTable of the ATM MIB [1] by it's Remote | ATM address and end point index. | Entries in this table are read only. They show up when entries are created in the | atmVclAddressTable. The atmAddrVclAtmIfIndex | appearing in the INDEX clause refers to the ATM | interface number (ifIndex in the atmInterfaceTable | of the ATM MIB [1]) that this VCL pertains to." | INDEX { atmRemoteAddr, atmAddrVclAtmIfIndex, | atmLocalAddrIndex } | ::= { atmAddrVclTable 1 } | AtmAddrVclEntry ::= | SEQUENCE { atmAddrVclAtmIfIndex IfIndex, | atmAddrVclVpi INTEGER, | atmAddrVclVci INTEGER | } atmAddrVclAtmIfIndex OBJECT-TYPE | SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The interface index of the ATM interface where this VCL pertains to. This object with | atmAddrVclVpi and atmAddrVclVci serve as an index | to the atmVclTable." ::= { atmAddrVclEntry 1 } | atmAddrVclVpi OBJECT-TYPE | SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The VPI value of the VCL. This object with | atmAddrVclAtmIfIndex and atmAddrVclVci serve as an | index | to the atmVclTable." ::= { atmAddrVclEntry 2 } | Expires XX [Page 35] draft Supplemental ATM Management Objects June 1995 atmAddrVclVci OBJECT-TYPE | SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The VCI value of the VCL. This object with | atmAddrVclAtmIfIndex and atmAddrVclVpi serve as an | index | to the atmVclTable." ::= { atmAddrVclEntry 3 } | Expires XX [Page 36] draft Supplemental ATM Management Objects June 1995 -- **************************************************** -- (6) ATM Host Signalling Group | -- This group contains information for a Host -- that implements ATM SVCs. This group includes the -- following table: -- 1. ATM Signalling Descriptor Parameter Table atmHostSigGroup OBJECT IDENTIFIER::= {atm2MIBObjects 5} | -- 1. ATM Signalling Descriptor Parameter Table -- This table contains objects to provide signalling | -- capabilities of VCLs. atmSigDescrParamTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmSigDescrParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table contains signalling capabilities of VCLs except the Traffic Descriptor. Traffic descriptors are described in the atmTrafficDescrParamTable." REFERENCE "ATM Forum's ATM User-Network Interface | Specification, Version 3.0, Section 5.4.5 Variable | Length Information | Elements." ::= { atmHostSigGroup 1 } | atmSigDescrParamEntry OBJECT-TYPE SYNTAX AtmSigDescrParamEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table represents a set of signalling capabilities that can be applied to a VCL. Objects atmSigDescrParamRowStatus is required during creation." INDEX { atmSigDescrParamIndex } ::= { atmSigDescrParamTable 1 } AtmSigDescrParamEntry ::= SEQUENCE { atmSigDescrParamIndex AtmSigDescrParamIndex, Expires XX [Page 37] draft Supplemental ATM Management Objects June 1995 atmSigDescrParamAalType INTEGER, atmSigDescrParamAalMode INTEGER, atmSigDescrParamAalSscsType INTEGER, atmSigDescrParamBhliType INTEGER, atmSigDescrParamBhliInfo OCTET STRING, atmSigDescrParamBbcClass INTEGER, atmSigDescrParamBbcTraffic INTEGER, atmSigDescrParamBbcTiming INTEGER, atmSigDescrParamBbcClipping INTEGER, atmSigDescrParamBbcConnConf INTEGER, atmSigDescrParamBlliLayer2 INTEGER, atmSigDescrParamBlliLayer3 INTEGER, atmSigDescrParamBlliPktSize INTEGER, atmSigDescrParamBlliSnapId INTEGER, atmSigDescrParamBlliOuiPid OCTET STRING, atmSigDescrParamRowStatus RowStatus } atmSigDescrParamIndex OBJECT-TYPE SYNTAX AtmSigDescrParamIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of this object is used by the atmVclExtTable to identify a row in this table." ::= { atmSigDescrParamEntry 1 } atmSigDescrParamAalType OBJECT-TYPE SYNTAX INTEGER { other(1), -- not defined aal1(2), -- AAL type 1 aal34(3), -- AAL type 3/4 aal5(4), -- AAL type 5 userDefined(5) -- User-Defined AAL } MAX-ACCESS read-create STATUS current DESCRIPTION "The AAL type. The value of this object is set to other(1) when not defined." DEFVAL { other } ::= { atmSigDescrParamEntry 2 } atmSigDescrParamAalMode OBJECT-TYPE SYNTAX INTEGER { Expires XX [Page 38] draft Supplemental ATM Management Objects June 1995 other(1), -- not defined msg(2), -- Message mode stream(3) -- Streaming mode } MAX-ACCESS read-create STATUS current DESCRIPTION "The AAL mode. The value of this object is other(1) when atmSigDescrParamAalType is aal1(2). Values msg(2) and stream(3) are only applicable when atmSigDescrParamAalType is set to aal34(3) or aal5(4). This object is applicable to UNI 3.0 only." DEFVAL { other } ::= { atmSigDescrParamEntry 3 } atmSigDescrParamAalSscsType OBJECT-TYPE SYNTAX INTEGER { other(1), -- other, or not used assured(2), -- Data SSCS based on SSCOP -- assured operation nonassured(3), -- Data SSCS based on SSCOP -- non-assured operation frameRelay(4) -- frame relay SSCS } MAX-ACCESS read-create STATUS current DESCRIPTION "The SSCS type used by this entry." DEFVAL { other } ::= { atmSigDescrParamEntry 4 } atmSigDescrParamBhliType OBJECT-TYPE SYNTAX INTEGER { other(1), -- not defined iso(2), -- ISO user(3), -- User specific hiProfile(4), -- Higher layer profile -- this enum applicable to -- UNI 3.0 only vendorSpecific(5) -- Vender specific -- application identifier } MAX-ACCESS read-create STATUS current Expires XX [Page 39] draft Supplemental ATM Management Objects June 1995 DESCRIPTION "The Broadband high layer type." DEFVAL { other } ::= { atmSigDescrParamEntry 5 } atmSigDescrParamBhliInfo OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..7)) MAX-ACCESS read-create STATUS current DESCRIPTION "The Broadband high layer information. When atmSigDescrParamBhliType is set to iso(2), the value of this object is a zero length string. When atmSigDescrParamBhliType is set to hiProfile(4), the value of this object is a length of 4 octet string containing user to user profile identifier. When atmSigDescrParamBhliType is set to vendorSpecific(4), the value of this object is a length of 7 octet string. The most significant 3 octets consist of a globally- administered OUI, the least significant 4 octets are the vender administered application OUI." DEFVAL { ''H } ::= { atmSigDescrParamEntry 6 } atmSigDescrParamBbcClass OBJECT-TYPE SYNTAX INTEGER { other(1), -- not defined or unspecified bcoba(2), -- BCOB-A bcobc(3), -- BCOB-C bcobx(4) -- BCOB-X } MAX-ACCESS read-only STATUS current DESCRIPTION "The Broadband bearer capability class." ::= { atmSigDescrParamEntry 7 } atmSigDescrParamBbcTraffic OBJECT-TYPE SYNTAX INTEGER { other(1), -- not defined noIndication(2), -- No indication cbr(3), -- Constant bit rate vbr(4) -- Variable bit rate } Expires XX [Page 40] draft Supplemental ATM Management Objects June 1995 MAX-ACCESS read-only STATUS current DESCRIPTION "The Broadband bearer capability traffic type." ::= { atmSigDescrParamEntry 8 } atmSigDescrParamBbcTiming OBJECT-TYPE SYNTAX INTEGER { other(1), -- not specified noIndication(2), -- No Indication required(3), -- end-to-end timing required notReq(4) -- end-to-end timing not -- required } MAX-ACCESS read-only STATUS current DESCRIPTION "The Broadband bearer capability timing requirements." ::= { atmSigDescrParamEntry 9 } atmSigDescrParamBbcClipping OBJECT-TYPE SYNTAX INTEGER { other(1), -- not specified true(2), -- not susceptible to -- clipping false(3) -- susceptible to clipping } MAX-ACCESS read-only STATUS current DESCRIPTION "The Broadband bearer capability susceptibility to clipping parameter." ::= { atmSigDescrParamEntry 10 } atmSigDescrParamBbcConnConf OBJECT-TYPE SYNTAX INTEGER { ptp(1), -- point-to-point ptmp(2) -- point-to-multipoint } MAX-ACCESS read-only STATUS current DESCRIPTION "The Broadband bearer capability user plane connection configuration parameter." Expires XX [Page 41] draft Supplemental ATM Management Objects June 1995 ::= { atmSigDescrParamEntry 11 } atmSigDescrParamBlliLayer2 OBJECT-TYPE SYNTAX INTEGER { other(1), -- not specified iso1745(2), -- Basic mode ISO 1745 q921(3), -- CCITT Recommendation Q.921 x25linklayer(4), -- CCITT Recommendation X.25 -- Link Layer x25multilink(5), -- CCITT Recommendation X.25 -- Multilink lapb(6), -- Extended LAPB; for half -- duplex operation hdlcArm(7), -- HDLC ARM (ISO 4335) hdlcNrm(8), -- HDLC NRM (ISO 4335) hdlcAbm(9), -- HDLC ABM (ISO 4335) iso88022(10), -- LAN logical link control -- (ISO 8802/2) x75slp(11), -- CCITT Recommendation X.75, -- single link -- procedure (SLP) q922(12), -- CCITT Recommendation Q.922 userDef(13), -- User specified iso7776(14) -- ISO 7776 DTE-DTE operation } MAX-ACCESS read-create STATUS current DESCRIPTION "The Broadband low layer information, protocol type of layer 2. The value of this object is other(1) if layer 2 protocol is not used." DEFVAL { other } ::= { atmSigDescrParamEntry 12 } atmSigDescrParamBlliLayer3 OBJECT-TYPE SYNTAX INTEGER { other(1), -- not specified x25pkt(2), -- CCITT Recommendation X.25 -- packet layer isoiec8208(3), -- ISO/IEC 8208 (X.25 packet -- level protocol for data -- terminal equipment) x223iso8878(4), -- X.223/ISO 8878 isoiec8473(5), -- ISO/IEC 8473 OSI -- connectionless Expires XX [Page 42] draft Supplemental ATM Management Objects June 1995 -- mode protocol t70(6), -- CCITT Recommendation T.70 -- minimum -- network layer tr9577(7), -- ISO/IEC TR 9577 Protocol -- Identification in the -- network layer userDef(8) -- user specified } MAX-ACCESS read-create STATUS current DESCRIPTION "The Broadband low layer information, protocol type of layer 3. The value of this object is other(1) if layer 3 protocol is not used." DEFVAL { other } ::= { atmSigDescrParamEntry 13 } atmSigDescrParamBlliPktSize OBJECT-TYPE SYNTAX INTEGER { other(1), -- not used s16(2), -- 16 octets s32(3), -- 32 octets s64(4), -- 64 octets s128(5), -- 128 octets s256(6), -- 256 octets s512(7), -- 512 octets s1024(8), -- 1028 octets s2048(9), -- 2048 octets s4096(10) -- 4096 octets } MAX-ACCESS read-create STATUS current DESCRIPTION "The default packet size defined in B-LLI." DEFVAL { other } ::= { atmSigDescrParamEntry 14 } atmSigDescrParamBlliSnapId OBJECT-TYPE SYNTAX INTEGER { other(1), -- not used true(2), -- SNAP ID is 1 false(3) -- SNAP ID is 0 } MAX-ACCESS read-create Expires XX [Page 43] draft Supplemental ATM Management Objects June 1995 STATUS current DESCRIPTION "The SNAP ID used for Broadband low layer protocol layer 3. The value of this object is other(1) if atmSigDescrParamBlliLayer3 is set to other(1)." DEFVAL { other } ::= { atmSigDescrParamEntry 15 } atmSigDescrParamBlliOuiPid OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..5)) MAX-ACCESS read-create STATUS current DESCRIPTION "The OUI/PID encoding for Broadband low layer | protocol layer 3. The value of this object is a zero length string if atmSigDescrParamBlliLayer3 is set to none(1). When used, it is always 5 octets with the most significant octet as the OUI Octet 1 and the least significant octet as the PID Octet 2." DEFVAL { ''H } ::= { atmSigDescrParamEntry 16 } atmSigDescrParamRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create and delete rows in the atmSigDescrParamTable. Writable values are: -'createAndWait' which allows manager to create an entry first and fill in the parameters later. -'active' which allows manager to set the entry to be available to users. -'destroy' which allows manager to delete an entry from this table. Readable values are: -'createAndWait' which means the entry is created but not available to be used. -'active' means it is active and ready to be used by agent or manager." ::= { atmSigDescrParamEntry 17 } Expires XX [Page 44] draft Supplemental ATM Management Objects June 1995 -- **************************************************** -- (7) ATM VP Interface Configuration Group -- This group contains information for interfaces -- supporting the ILMI-over-VPC scenario. -- This group includes the following table: -- 1. ATM VP Interface Configuration Table atmVPIfConfGroup OBJECT IDENTIFIER::= {atm2MIBObjects 6} | -- 1. ATM VP Interface Configuration Table -- This table contains objects to provide the ILMI -- and neighbor information for the ILMI-over-VPC -- scenario. atmVplIfConfTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmVplIfConfEntry | MAX-ACCESS not-accessible | STATUS current | DESCRIPTION "The ILMI and neighbor information for the ILMI- over-VPC scenario." ::= { atmVPIfConfGroup 1 } atmVplIfConfEntry OBJECT-TYPE SYNTAX AtmVplIfConfEntry MAX-ACCESS not-accessible | STATUS current | DESCRIPTION "An entry with ILMI and Neighbor information." AUGMENTS { atmVplEntry } ::= { atmVplIfConfTable 1 } | AtmVplIfConfEntry ::= SEQUENCE { atmVplIlmiVci INTEGER, | atmVplIfMyNeighborIpAddress IpAddress, | atmVplIfMyNeighborIfName DisplayString, | atmVplIfMyNeighborsysDescr DisplayString, | atmVplIfMyNeighborsysObjectID OBJECT IDENTIFIER | } atmVplIlmiVci OBJECT-TYPE SYNTAX INTEGER (0..65535) | MAX-ACCESS read-write | Expires XX [Page 45] draft Supplemental ATM Management Objects June 1995 STATUS current | DESCRIPTION "The VCI value of the VPC supporting the ILMI at this VPL interface. If the value is zero then the ILMI is not supported at this VPL interface." DEFVAL { 0 } ::= { atmVplIfConfEntry 1 } | atmVplIfMyNeighborIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write | STATUS current | DESCRIPTION "The IP address of the neighbor system connected to the far end of this VPL interface, to which a Network Management Station can send SNMP messages, as IP datagrams sent to UDP port 161, in order to access network management information concerning the operation of that system. Note that the value of this object may be obtained in different ways, e.g., by manual configuration, or through ILMI interaction with the neighbor system." ::= { atmVplIfConfEntry 2 } | atmVplIfMyNeighborIfName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write | STATUS current | DESCRIPTION "The textual name of the interface on the neighbor system on the far end of this VPL interface, and to which this interface connects. If the neighbor system is manageable through SNMP and supports the object ifName, the value of this object must be identical with that of ifName for the ifEntry of the lowest level physical interface for this port. If this interface does not have a textual name, the value of this object is a zero length string. Note that the value of this object may be obtained in different ways, e.g., by manual configuration, or through ILMI interaction with the neighbor system." ::= { atmVplIfConfEntry 3 } | atmVplIfMyNeighborsysDescr OBJECT-TYPE + Expires XX [Page 46] draft Supplemental ATM Management Objects June 1995 SYNTAX DisplayString (SIZE(0..255)) + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object must be identical to the sysDescr + object of the neighbor system connected to the far + end of this VPL interface." + ::= { atmVplIfConfEntry 4 } + atmVplIfMyNeighborsysObjectID OBJECT-TYPE + SYNTAX OBJECT IDENTIFIER + MAX-ACCESS read-write + STATUS current + DESCRIPTION + "This object must be identical to the sysObjectID + object of the neighbor system connected to the far + end of this VPL interface." + ::= { atmVplIfConfEntry 5 } + Expires XX [Page 47] draft Supplemental ATM Management Objects June 1995 -- ************************************************ -- Conformance Information atm2MIBConformance OBJECT IDENTIFIER ::= {atm2MIB 2} atm2MIBGroups OBJECT IDENTIFIER ::= {atm2MIBConformance 1} atm2MIBCompliances OBJECT IDENTIFIER ::= {atm2MIBConformance 2} -- Compliance Statements atm2MIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which represent ATM interfaces. The compliance statements are used to determine if a particular group or object applies to hosts, networks/switches, or both." MODULE -- this module MANDATORY-GROUPS { atmSwitchNetHostGroup } -- Objects in the ATM Switch/Network/Host Group - OBJECT atmVclConnType MIN-ACCESS read-only DESCRIPTION "Write access is not required. This object is required for hosts that support SVCs and PVCs for ATM." OBJECT atmVclStatCellIns + DESCRIPTION + "Write access is not required. This object is + mandatory for systems that are supporting per VCC + counters." + OBJECT atmVclStatCellOuts | DESCRIPTION "Write access is not required. This object is | mandatory for systems that are supporting per VCC | counters." | Expires XX [Page 48] draft Supplemental ATM Management Objects June 1995 OBJECT atmVplStatCellIns | DESCRIPTION "Write access is not required. This object is | mandatory for systems that are supporting per VPC | counters." | OBJECT atmVplStatCellOuts | DESCRIPTION "Write access is not required. This object is | mandatory for systems that are supporting per VPC | counters." | -- The ATM Switch/Network/Host SVC Group | GROUP atmSwitchNetHostSVCGroup | DESCRIPTION "This group is mandatory for a Switch/Network/Host | that implements ATM interfaces supporting SVCs." | OBJECT atmSvcSigEntityRole | MIN-ACCESS read-only DESCRIPTION "Write access is not required" OBJECT atmSvcSigType | MIN-ACCESS read-only DESCRIPTION "Write access is not required" -- The ATM Switch/Network Group - GROUP atmSwitchNetGroup | DESCRIPTION "This group is mandatory for a Switch/Network that implements ATM interfaces." OBJECT atmIfAdminAddrRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." Expires XX [Page 49] draft Supplemental ATM Management Objects June 1995 -- The ATM Switch/Network SVC Group GROUP atmSwitchNetSVCGroup | DESCRIPTION "This group is mandatory for a Switch/Network that implements ATM interfaces supporting Switched Virtual Connections (SVCs)." OBJECT atmSvcSupportClgPtyNumDel MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSvcSupportClgPtySubAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSvcSupportCldPtySubAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSvcSupportHiLyrInfo MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSvcSupportLoLyrInfo MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSvcSupportRepeatInd MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSvcSupportAALInfo MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSvcSupportPrefCarrier MIN-ACCESS read-only Expires XX [Page 50] draft Supplemental ATM Management Objects June 1995 DESCRIPTION "Write access is not required." -- The ATM Host Group GROUP atmHOSTGroup | DESCRIPTION "This group is mandatory for a Host that implements ATM interfaces." OBJECT atmRemoteAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmLocalAddr MIN-ACCESS read-only DESCRIPTION "Write access is not required." -- The ATM Host SVC Group GROUP atmHOSTSigGroup | DESCRIPTION "This group is mandatory for a Host that implements ATM SVCs." OBJECT atmVclSigDescrIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamAalType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamAalMode MIN-ACCESS read-only DESCRIPTION "Write access is not required." Expires XX [Page 51] draft Supplemental ATM Management Objects June 1995 OBJECT atmSigDescrParamAalSscsType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamBhliType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamBhliInfo MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamBlliLayer2 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamBlliLayer3 MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamBlliPktSize MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamBlliSnapId MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamBlliOuiPid MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmSigDescrParamRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual Expires XX [Page 52] draft Supplemental ATM Management Objects June 1995 convention need be supported, specifically: active(1)." -- The ATM VP Interface Configuration Group GROUP atmVpIfConfGroup | DESCRIPTION "This group is mandatory for interfaces that support ILMI-over-VPC scenario." OBJECT atmVplIlmiVci MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmVplIfMyNeighborIpAddress MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmVplIfMyNeighborIfName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT atmVplIfMyNeighborsysDescr + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + OBJECT atmVplIfMyNeighborsysObjectID + MIN-ACCESS read-only + DESCRIPTION + "Write access is not required." + ::= { atm2MIBCompliances 1 } + -- ********************************************** -- Units of Conformance atmSwitchNetHostGroup OBJECT-GROUP | Expires XX [Page 53] draft Supplemental ATM Management Objects June 1995 OBJECTS { atmVclConnType, | atmVclStatCellIns, | atmVclStatCellOuts, | atmVplStatCellIns, | atmVplStatCellOuts} | STATUS current DESCRIPTION "A collection of objects providing information for a Switch/Network/Host that implements ATM interfaces." ::= { atm2MIBGroups 1 } atmSwitchNetHostSVCGroup OBJECT-GROUP | OBJECTS { atmSvcSigEntityRole, - atmSvcSigType, atmSvcSSCOPConMontrs, - atmSvcSSCOPErrdPdus, atmSvcUnavailRoutes, atmSvcUnavailResrcs, atmSvcCldPrtyProblems, atmSvcSigMsgErrors, atmSvcSigTimerExpireds, atmSvcSigRestarts, atmSvcSigInEstabls, atmSvcSigOutEstabls} STATUS current DESCRIPTION "A collection of objects providing information for a Switch/Network/Host that implements ATM SVCs." ::= { atm2MIBGroups 2 } | atmSwitchNetGroup OBJECT-GROUP | OBJECTS { atmIfAdminAddrRowStatus} - STATUS current DESCRIPTION "A collection of objects providing information for a Switch/Network that implements ATM interfaces." Expires XX [Page 54] draft Supplemental ATM Management Objects June 1995 ::= { atm2MIBGroups 3 } | atmSwitchNetSVCGroup OBJECT-GROUP | OBJECTS { atmSvcSupportClgPtyNumDel, atmSvcSupportClgPtySubAddr, atmSvcSupportCldPtySubAddr, atmSvcSupportHiLyrInfo, atmSvcSupportLoLyrInfo, atmSvcSupportRepeatInd, atmSvcSupportAALInfo, atmSvcSupportPrefCarrier} STATUS current DESCRIPTION "A collection of objects providing information for a Switch/Network that implements ATM SVCs." ::= { atm2MIBGroups 4 } | atmHOSTGroup OBJECT-GROUP | OBJECTS { atmRemoteAddr, atmLocalAddr, atmAddrVclAtmIfIndex, | atmAddrVclVpi, | atmAddrVclVci} | STATUS current DESCRIPTION "A collection of objects providing information for a Host that implements ATM interfaces." ::= { atm2MIBGroups 5 } | atmHOSTSigGroup OBJECT-GROUP | OBJECTS { atmVclSigDescrIndex, atmSigDescrParamAalType, atmSigDescrParamAalMode, atmSigDescrParamAalSscsType, atmSigDescrParamBhliType, atmSigDescrParamBhliInfo, Expires XX [Page 55] draft Supplemental ATM Management Objects June 1995 atmSigDescrParamBbcClass, atmSigDescrParamBbcTraffic, atmSigDescrParamBbcTiming, atmSigDescrParamBbcClipping, atmSigDescrParamBbcConnConf, atmSigDescrParamBlliLayer2, atmSigDescrParamBlliLayer3, atmSigDescrParamBlliPktSize, atmSigDescrParamBlliSnapId, atmSigDescrParamBlliOuiPid, atmSigDescrParamRowStatus} STATUS current DESCRIPTION "A collection of objects providing information for a Host that implements ATM interfaces supporting Switched Virtual Connections (SVCs)." ::= { atm2MIBGroups 6 } | atmVpIfConfGroup OBJECT-GROUP | OBJECTS { atmVplIlmiVci, atmVplIfMyNeighborIpAddress, atmVplIfMyNeighborIfName, | atmVplIfMyNeighborsysDescr, | atmVplIfMyNeighborsysObjectID} | STATUS current DESCRIPTION "A collection of objects providing information for interfaces that support ILMI and neighbor information for the ILMI-over-VPC scenario." ::= { atm2MIBGroups 7 } | END Expires XX [Page 56] draft Supplemental ATM Management Objects June 1995 9. Acknowledgments This document is a product of the AToMMIB Working Group. Expires XX [Page 57] draft Supplemental ATM Management Objects June 1995 10. References [1] Ahmed, M., Tesink, K., "Definitions of Managed Objects for ATM Management Version 8.0 using SMIv2", RFC 1695, Bell Communications Research, August 1994. [2] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1442, SNMP Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993. [3] McCloghrie, K., and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, Hughes LAN Systems, Performance Systems International, March 1991. [4] Galvin, J., and K. McCloghrie, "Administrative Model for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1445, Trusted Information Systems, Hughes LAN Systems, April 1993. [5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1448, SNMP Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993. [6] McCloghrie, K. and F. Kastenholz, "Evolution of the Interfaces Group of MIB-II", RFC 1573, Hughes LAN Systems, FTP Software, January 1994. [7] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for SNMPv2", RFC1443, SNMP Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993. [8] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for SNMPv2", RFC1444, SNMP Research,Inc., Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon University, April 1993. [9] ATM Forum, "ATM User-Network Interface, Version 3.0 (UNI 3.0) Specification, Part I", 1994. Expires XX [Page 58] draft Supplemental ATM Management Objects June 1995 [10] ATM Forum, "ATM User-Network Interface, Version 3.1 (UNI 3.1) Specification, Part I", November 1994. [11] ITU-T Recommendation Q.2931, "Broadband Integrated Service Digital Network (B-ISDN) Digital Service Signalling System No.2 (DSS2) User-Network Interface (UNI) Layer 3 Specification for Basic Call/Connection Control", September 1994. [12] ATM Forum 94-0471R4, "P-NNI Draft Specification, P-NNI SWG", November 1994. [13] ITU-T Draft Recommendation Q.2110, "Broadband Integrated Service Digital Network (B-ISDN) - ATM Adaptation Layer - Service Specific Connection Oriented Protocol (SSCOP) Specification", 1994. [14] Newton, T., "Baseline Text For LAN Emulation Client Management", ATM Forum Contribution 94-0737R1, Digital Equipment Corporation, January 1995. [15] Brown, T., Tesink, K., "Definitions of Managed Objects for SMDS Interfaces using SMIv2", RFC 1694, Bell Communications Research, August 1994. [16] ATM Forum, "ATM User-Network Interface, Version 4.0 (UNI 4.0) Specification, Part I", 1995. - Expires XX [Page 59] draft Supplemental ATM Management Objects June 1995 11. Security Considerations Security issues are not discussed in this memo. 12. Authors' Addresses Faye Ly BayNetworks Communications, Inc. 4401 Great America Pkwy Santa Clara, CA 95052 Phone: (408) 764-1702 EMail: faye@Baynetworks.COM Michael Noto Bell Communications Research Room 1E-348 331 Newman Springs Road P.O. Box 7020 Red Bank, NJ 07701-7020 Phone: (908) 758-5104 EMail: noto@cc.bellcore.com Andrew Smith BayNetworks Communications, Inc. 4401 Great America Pkwy Santa Clara, CA 95052 Phone: (408) 764-1574 EMail: asmith@Baynetworks.COM Kaj Tesink Bell Communications Research Room 1A-427 331 Newman Springs Road P.O. Box 7020 Red Bank, NJ 07701-7020 Phone: (908) 758-5254 EMail: kaj@cc.bellcore.com Expires XX [Page 60] draft Supplemental ATM Management Objects June 1995 Table of Contents 1 Status of this Memo ................................... 1 2 Introduction .......................................... 2 3 The SNMPv2 Network Management Framework ............... 2 4 Object Definitions .................................... 3 5 Overview .............................................. 3 5.1 Background .......................................... 3 5.2 Supported Functions ................................. 4 5.2.1 ATM Switch/Network/Host Support ................... 4 5.2.1.1 ATM Switch/Network/Host Group ................... 4 5.2.1.1.1 ATM VCL Statistics Table ...................... 4 5.2.1.1.2 ATM VPL Statistics Table ...................... 5 5.2.1.2 ATM Switch/Network/Host SVC Group ............... 5 5.2.1.2.1 ATM Interface SVC Configuration ............... 5 5.2.1.2.2 SSCOP ......................................... 5 5.2.1.2.3 Unsupported Service Failures .................. 5 5.2.1.2.4 ATM Signalling Layer Protocol Errors .......... 6 5.2.1.2.5 UNI Signalling Sub-layer Statistics ........... 6 5.2.1.2.6 Indexing of the atmSvcTable ................... 7 5.2.2 ATM Switch/Network Support ........................ 7 5.2.2.1 ATM Switch/Network Group ........................ 7 5.2.2.1.1 ATM Interface Administrative Address Table .... 7 5.2.2.2 ATM Switch/Network SVC Group .................... 7 5.2.2.2.1 ATM UNI SVC Information Element Support ....... 7 5.2.3 ATM Host Support .................................. 8 5.2.3.1 ATM Host Group .................................. 8 5.2.3.1.1 VCL Extension Table ........................... 8 5.2.3.1.2 ATM VPI/VCI to Address Mapping Table .......... 8 5.2.3.1.3 ATM Address to VPI/VCI Mapping Table .......... 9 5.2.3.2 ATM Host SVC Group .............................. 9 5.2.3.2.1 Signalling Descriptor Parameter Table ......... 9 5.2.4 Signalling-over-VPC Support ....................... 10 5.2.4.1 ATM VP Interface Configuration .................. 10 6 Valid Address Sets / Default Address .................. 10 7 Configuration of VPLs, VCLs, and Cross-Connects ....... 10 8 Definitions ........................................... 11 9 Acknowledgments ....................................... 57 10 References ........................................... 58 11 Security Considerations .............................. 60 12 Authors' Addresses ................................... 60 Expires XX [Page 61] draft Supplemental ATM Management Objects June 1995 Expires XX [Page 62]