INTERNET-DRAFT ADSL Line MIB Gregory Bathrick AG Communication Systems August 7, 1998 Definitions of Managed Objects for the ADSL Lines August 7, 1998 draft-ietf-adslmib-adsllinemib-01.txt 1. Status of this Memo This document is an Internet-Draft. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as ``work in progress.'' To view the entire list of current Internet-Drafts, please check the "1id-abstracts.txt" listing contained in the Internet-Drafts Shadow Directories on ftp.is.co.za (Africa), ftp.nordu.net (Northern Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au (Pacific Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu (US West Coast). 2. Abstract This document defines a standard SNMP MIB for ADSL lines based on the ADSL Forum standard data model [9]. The model assumed by this MIB is that the SNMP agent's perspective is from the ATU-C side which acts as a proxy for the ATU-R. Each MIB instance includes information for both ends of a single line, i.e., both the ATU-C and ATU-R. It should be noted that much of the content for the first version of this document came from work completed by the ADSL Forum's Network Expires February 1999 [Page 1] INTERNET-DRAFT ADSL Line MIB August 7, 1998 Management working group and documented in ADSL Forum TR-006 "SNMP- based ADSL Line MIB"[9]. See Acknowledgement Section for a list individuals of those involved with this effort. 3. The SNMP Network Management Framework The SNMP Management Framework presently consists of five major components: o An overall architecture, described in RFC 2271 [13]. o Mechanisms for describing and naming objects and events for the purpose of management. The first version of this Structure of Management Information (SMI) is called SMIv1 and described in RFC 1155 [14], RFC 1212 [15] and RFC 1215 [16]. The second version, called SMIv2, is described in RFC 1902 [1], RFC 1903 [2] and RFC 1904 [17]. o Message protocols for transferring management information. The first version of the SNMP message protocol is called SNMPv1 and described in RFC 1157 [7]. A second version of the SNMP message protocol, which is not an Internet standards track protocol, is called SNMPv2c and described in RFC 1901 [18] and RFC 1906 [19]. The third version of the message protocol is called SNMPv3 and described in RFC 1906 [19], RFC 2272 [20] and RFC 2274 [21]. o Protocol operations for accessing management information. The first set of protocol operations and associated PDU formats is described in RFC 1157 [7]. A second set of protocol operations and associated PDU formats is described in RFC 1905 [9]. o A set of fundamental applications described in RFC 2273 [22] and the view-based access control mechanism described in RFC 2275 [23]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the mechanisms defined in the SMI. This document specifies a MIB module that is compliant to the SMIv2. A MIB conforming to the SMIv1 can be produced through the appropriate translations. The resulting translated MIB must be semantically equivalent, except where objects or events are omitted because no translation is possible (e.g., use of Counter64). Some machine readable information in SMIv2 will be converted into textual Expires February 1999 [Page 2] INTERNET-DRAFT ADSL Line MIB August 7, 1998 descriptions in SMIv1 during the translation process. However, this loss of machine readable information is not considered to change the semantics of the MIB. 4. Object Definitions Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. Objects in the MIB are defined using the subset of Abstract Syntax Notation One (ASN.1) defined in the SMI. In particular, each object type is named by an OBJECT IDENTIFIER, an administratively assigned name. The object type together with an object instance serves to uniquely identify a specific instantiation of the object. For human convenience, we often use a textual string, termed the descriptor, to also refer to the object type. 5. Introduction This document describes an ADSL Line MIB which is intended to work within the SNMP Network Management Framework (section 3). All MIB definitions are backward compatible for SNMPv1 implementation. The MIB definitions are attached. The MIB will eventually be located in the MIB tree under MIB 2 transmission, as discussed in the MIB-2 Integration (RFCs 1213 [4] and 2233 [5]) section of this document. Until approved by the IETF, vendors may also choose to support it under their own enterprise IDs. adslLineMIB MODULE-IDENTITY ::= { VendorEnterpriseID nnn} 6. Relationship of the ADSL LINE MIB with standard MIBs This section outlines the relationship of this MIB with other MIBs described in RFCs and in various degrees of "standardization". MIB-2 (RFC 1213 [4] and 2233 [5]) and the Entity MIB (RFC 2037 [25]) are discussed below. 6.1 General MIB-2 Integration (RFCs 1213 [4] and 2233 [5]) The ADSL LINE MIB specifies the detailed attributes of a data interface. As such, it needs to integrate with MIB-2 ([4] and [5]). The IANA has assigned the following ifType(s) for XDSL: Expires February 1999 [Page 3] INTERNET-DRAFT ADSL Line MIB August 7, 1998 IANAifType ::= TEXTUAL-CONVENTION . . . SYNTAX INTEGER { . . . adsl(94), -- Asymmetric Digital Subscriber Loop radsl(95), -- Rate-Adapt. Digital Subscriber Loop sdsl(96), -- Symmetric Digital Subscriber Loop vdsl(97), -- Very H-Speed Digital Subscrib. Loop . . . adslInterleave(124), -- ADSL Interleaved Channel adslFast(125), -- ADSL Fast Channel } Of these, only adsl, adslFast, and adslInterleave are used with this MIB. Use of radsl, sdsl, and vdsl is for further study (or they may have their own MIBs). Therefore, pending approval of the IETF, RFC 2233 [5] mandates that this MIB will be accessed through mib-2.transmission.ifType as shown: adslPhysIf ::= { transmission 94 } -- Physical tables adslInterIf ::= { transmission 124 } -- Interleaved Channel tables adslFastIf ::= { transmission 125} -- Fast Channel tables with each MIB branch containing the appropriate tables for that interface type, as discussed below. Most such tables extends the ifEntry table, and are indexed by ifIndex. In addition, there are two "profile" tables which may be accessed by ifIndex, or profileIndex depending on the profile mode implemented. This is explained in detail in section 7.4 Profiles. 6.1.1 ADSL Interface Types Expires February 1999 [Page 4] INTERNET-DRAFT ADSL Line MIB August 7, 1998 As shown below, three ADSL interface types are defined in this document, namely physical, interleaved channel, and fast channel. The physical interface represents characteristics of the physical media associated with both the ATUC and ATUR. The interleaved and fast channel interface represent the characteristics of the two types of ADSL channels. For each ADSL Line, a physical interface always exists. Depending on which ADSL operational configuration is present (as listed in Figure 5), the channel interfaces (fast or interleaved) may or may not be exist. ______ ______ | |____________________| | | ATUC | | ATUR | | |____________________| | |______| |______| | <----- physical --------> | | <--- fast channel ------> | | <- interleaved channel -> | Figure 1: ADSL Model 6.1.2 Use of Interface MIB RFC 2233 [5] The following attributes are part of the mandatory ifGeneralInformationGroup object group specified in RFC 2233 [5], and are not duplicated in the ADSL MIB. Remember that these objects apply to the line, not either end in particular. ifDescr - "manufacturer's name, model number, version number" associated with all ADSL interface entry types ifType - 94, 124, or 125, for physical, interleaved, and fast interface entries respectively ifSpeed - transmit rate from the perspective of the ATU-C interface, aka the "downstream" rate ifPhysAddress - not applicable for ADSL interface entries, must be 0-length string Expires February 1999 [Page 5] INTERNET-DRAFT ADSL Line MIB August 7, 1998 ifAdminStatus, ifOperStatus - normal use, supplemented by adslAtucCurrStatus and adslAturCurrStatus for physical interfaces entry types only ifLastChange - The value of the last state change for all ADSL interface entry types ifLinkUpDownTrapEnable - default to Enable (1) for physical layer entry types, and to Disable (2) for interleaved, and fast interface channel entry types. ifConnectorPresent - set to True (1) for physical layer entries, and to False (2) interleaved, and fast interface entry types ifHighSpeed - As ADSL operates at a maximum rate of about 8Mbps circa 1997, ifHighSpeed is irrelevant, and is set to zero. ifName - Textual name for the interface allowing the network manager ability to associate an ifEntry with a specific node/shelf/slot/port of the ADSL equipment. ifNumber - The total number of ADSL network interfaces present on the system. ifAlias - A configurable textual name for the interface allowing the network manager ability to associate an ifEntry with a specific node/shelf/slot/port of the ADSL equipment. This information is held in non-volatile storage. ifTableLastChange - The value of sysUpTime at the time of the last creation or deletion of an entry in the ifTable. The following attributes are from the ifFixedLengthGroup [5] which is optional, but is the closest set to ADSL. They may optionally be implemented when appropriate. ifInOctets, ifOutOctets - counted from the perspective of the ATU-C interface for all ADSL interface entry types ifInUnknownProtos, ifInErrors, ifOutErrors - counted from the perspective of the ATU-C interface for all ADSL interface entry types The table below shows this information in a more concise format. "Normal" means the object is used as specified by RFC 2233. The designations "i", "j", and "k" indicate three arbitrary ifIndex values, corresponding to the physical, interleaved, and fast entries for a single ADSL Line. These designations are used throughout this Expires February 1999 [Page 6] INTERNET-DRAFT ADSL Line MIB August 7, 1998 document. MIB Object Physical Line(i) Interleaved Fast Channel (j) Channel(k) ---------------------------------------------------------------------- ifDescr NORMAL NORMAL NORMAL ifType(IANA) 94 124 125 ifSpeed ATU-C ATU-C ATU-C Line Tx Channel Tx Channel Tx Rate Rate Rate ifPhysAddress NULL NULL NULL ifAdminStatus NORMAL NORMAL NORMAL ifOperStatus NORMAL NORMAL NORMAL ifLastChange NORMAL NORMAL NORMAL ifLinkUpDown- NORMAL NORMAL NORMAL TrapEnable (default: (default: (default: Enable) Disable) Disable) ifConnectorPresent True False False ifHighSpeed zero zero zero ifName NORMAL NORMAL NORMAL ifNumber NORMAL NORMAL NORMAL ifAlias NORMAL NORMAL NORMAL ifTableLastChange NORMAL NORMAL NORMAL ---------------------------------------------------------------------- Figure 2: Use of ifTable Objects Use the ifTest table for Diagnostic tests, which extends ifEntry. The adslLineMib defines ADSL-specific values for ifTestTypes and ifTestCodes. Use the ifStackTable to associate the entries for physical, fast, interleaved channels, and higher layers (e.g., ATM) is shown below in figure 3. Use of ifStackTable is necessary, because configuration Expires February 1999 [Page 7] INTERNET-DRAFT ADSL Line MIB August 7, 1998 information is stored in profile tables associated with the physical-layer ifEntry only. The channels ifEntrys need the ifStackTable to find their associated physical-layer entry and thus their configuration parameters. (See Profile section, 7.4). ______ (ifEntry=k) ______ | | fast channel | | | |________________________| | | | and/or | | | | | | | | (ifEntry=j) | | | | interleaved channel | | | |________________________| | | ATUC | | ATUR | | | | | | | (ifEntry=i) | | | | physical | | | |________________________| | |______| |______| Figure 3: Use of ifStackTable (part 1) The ifStackTable is then used to show the relationships between the various ADSL interfaces, as illustrated below in Figure 4. HigherLayer LowerLayer -------------------------- k i j i Figure 4: Use of ifStackTable (part 2) 6.2 Relationship with RFC 2037 [25] Implementation of the Entity MIB [25] is optional. It in no way alters the information required in the adslLineMib, nor does it alter the relationship with MIB-2, ifIndex, and ifStackTable. The Entity MIB introduces a standardized way of presenting the components of complex systems, such as a Digital Subscriber Line Access Multiplexer (DSLAM), that may contain multiple racks, shelves, line cards, and/or ports. The Entity MIB's main goal is to present these system components, their containment relationship, and mapping information Expires February 1999 [Page 8] INTERNET-DRAFT ADSL Line MIB August 7, 1998 with other MIBs such as the Interface MIB and the adslLineMib. If implemented, the Entity MIB should include entities for the ATU-C and ATU-R in the entPhysicalTable. The MIB's entAliasMappingTable would contain mapping information identifying the 'ifIndex' object associated with each ATU-C and ATU-R. Also associating the relationship between the ifTable and Entity MIB, the entPhysicalTable contains an 'entPhysicalName' object, which approximates the semantics of the 'ifName' object from the Interface MIB. 7. Conventions used in the MIB 7.1 Naming Conventions A. Atuc/Atur are used for the ATU-C and ATU-R. In other RFCs, these are sometimes referred to as the Near End (Ne) and Far End (Fe) respectively, but not in this document. B. The terms, "transmit" and "receive", are from the perspective of the corresponding table's end of the line. For example, adslAtucChanConfMaxTxRate defines the "downstream" rate, while adslAturChanConfMaxTxRate defines the "upstream" rate for a particular channel. C. There are two possible channels: fast, and interleaved. None, one or both may be implemented on a particular ADSL Line. Figure 5 illustrates all possible operational configurations. D. Lof, Lol, Los, Lpr mean Loss of Framing, Link, Signal, and Power, respectively. Lpr is used by T1E1, so it is used for consistency (rather than Lop). A Loss of Link condition is declared at the ATU-C if a Loss of Signal is not preceded by a 'dying-gasp' message from the ATU-R. Note that Loss of Link is only supported by the ATU-C. E. ES means errored second. An Errored Second is any second containing one or more CRC anomaly, or one or more Los(s) or Severely Errored Frame (Sef) defect(s). F. A "block" is a physical-layer 'data buffer' over which CRCs are calculated. For example, in DMT, the block is defined as the ADSL superframe. The block duration is 250 micro-seconds so the block length in bytes, as defined in adslAtu*ChanCrcBlockLength, varies with data rate. See Line Code Specific MIBs [11] [12] for more line code specific information. Expires February 1999 [Page 9] INTERNET-DRAFT ADSL Line MIB August 7, 1998 G. Atn means Attenuation, Psd is Power Spectral Density and Snr is Signal to Noise Ratio. H. LCS means line code specific, e.g., o DMT = Discrete MultiTone o CAP = Carrierless Amplitude and Phase modulation and o QAM = Quadrature Amplitude Modulation I. Vendor (in the Inventory objects) refers to the manufacturer or the ATU-C or ATU-R assembly, not the modem chip vendor. When in doubt, use the manufacturer of the smallest field replaceable unit (e.g., stand-alone modem box, plug-in board). 7.2 Structure The MIB has multiple parallel tables. There are tables for: o line - common attributes o atuc and atur status o atuc and atur performance - Current and up to 96 buckets of 15 min performance history - Current and Previous 1-day bucket performance history o profiles - configuration parameters and alarm parameters There are separate tables for Physical and Channel layers. Since their attributes are similar, only one set of "channel" tables are defined to be used for both fast and interleaved channels. The corresponding ifType gives the proper interpretation for that ifEntry. Finally, there are separate LCS tables, also for each end. These are currently stubs. These will each be separate MIB Modules. There could have been fewer tables by combining the ATU-C and ATU-R information into shared tables. However, the tables are more easily read when there are two identical sets of data. The figure below lists the five possible ADSL operational Expires February 1999 [Page 10] INTERNET-DRAFT ADSL Line MIB August 7, 1998 configurations. (indicated by the value of the adslLineType). In all configurations, the physical line interface entry will exist. However, the existence of the ADSL channel varies in each case, as shown below. Table Phys Fast Interleaved ___________________________________________________________ No Channels (1) | Y | | | Fast Only (2) | Y | Y | | Interleaved Only (3) | Y | | Y | Fast or Interleaved (4) | Y | Y | Y | Fast and Interleaved (5) | Y | Y | Y | Figure 5: ADSL Operational configurations NOTE: In (4), channel exists of either Fast or Interleaved type, but not both. The Manager may select the type of channel to be used. Depending on which operation configuration exists, some or all ADSL MIB tables could be supported, as shown in below. See Conformance Statements for more information on which objects are mandatory. Table Phys Fast Interleaved ___________________________________________________________ adslLineTable | Y | | | adslAtucPhysTable | Y | | | adslAturPhysTable | Y | | | adslAtucChanTable | | Y | Y | adslAturChanTable | | Y | Y | adslAtucPerfDataTable | Y | | | adslAturPerfDataTable | Y | | | adslAtucIntervalTable | Y | | | adslAturIntervalTable | Y | | | adslAtucChanPerfDataTable | | Y | Y | adslAturChanPerfDataTable | | Y | Y | adslAtucChanIntervalTable | | Y | Y | adslAturChanIntervalTable | | Y | Y | Figure 6: Use of ADSL MIB Tables with various ifIndex values NOTE: For adslLineConfProfileTable and adslLineAlarmConfProfileTable will be present for all scenarios. See Profile Section of this document for implementation details such as profile creation, assignment, and indexing. Expires February 1999 [Page 11] INTERNET-DRAFT ADSL Line MIB August 7, 1998 7.3 Counters, Interval Buckets and Thresholds For physical-level ES, Los, Lof, Lol, Lpr and line initialization attempts, there are event counters, current 15-minute and one (up to 96) 15-minute history bucket(s) of "interval-counters", as well as current and previous 1-day interval-counters. There is no requirement for an agent to ensure fixed relationship between the start of a fifteen minute and any wall clock; however some implementations may align the fifteen minute intervals with quarter hours. Likewise, an implementation may choose to align one day intervals with start of a day. In all cases, the sum of the corresponding 15-minute interval timers for the current day should equal the current 1-day timers. However, in most cases, this will not be the sum of all 96 intervals, as they represent a rolling set of data. At the channel level, there are counters for total received blocks, received-and-corrected blocks, received-but-uncorrectable blocks, and transmitted blocks. Blocks are counted here because octets are counted by ifInOctets, ifOutOctets. There are the same set of 15- minute and 1-day buckets as at the physical layer. Separate tables are provided for the 96 interval-counters. They are indexed by {ifIndex, AdslAtu*IntervalNumber}. Every physical layer object with a 15 minute current bucket also has a 15-min threshold trap. Counters are not reset when an ATU-C is reinitialized, only when the agent is reset or reinitialized (or under specific request outside the scope of this MIB). 7.4 Profiles As a managed node can handle a large number of ATU-Cs (e.g., hundreds or perhaps thousands of ADSL lines), provisioning every parameter on every ATU-C may become burdensome. In response, two MIB tables have been created to define ADSL equipment configuration data profiles, as well as a mechanism to associate the equipment to these profiles. This concept is similar to the one used in ATM MIB (RFC 1695[24]) to define ATM traffic descriptor sets. Profile tables may be implemented in one of two ways, but not simultaneously: Expires February 1999 [Page 12] INTERNET-DRAFT ADSL Line MIB August 7, 1998 o MODE-I: Dynamic Profiles - one profile shared by one or multiple ADSL lines. o MODE-II: Static Profiles - one profile per ADSL physical line always. 7.4.1 MODE-I : Dynamic Profiles Implementations using this mode will enable the manager to dynamically create and delete profiles as needed. The index of the profile is an arbitrary integer in the range 1..N, where N is the maximum number of profiles supported by the equipment and is implementation specific. One or more ADSL lines may be configured to share parameters of a single profile (say adslLineConfProfileIndex = 'n') by setting their adslLineConfProfile objects to the value of profile's index (n). If a change is made to Profile-n, all lines that refer to it will be re-configured to the changed parameters. The next figure shows an example of how this mode can be implemented. In the example, ADSL lines '1' and 'x' share the configuration in Profile-n, while line '2' uses Profile-1. Please note that all three entries for each ADSL line, physical layer, the fast channel, and the interleaved channel, are represented by "i", "j", and "k" as before. However, only the physical-layer entry "i" contains an adslLineTable entry, so only those entries contain pointers to the adslConfProfileEntry. The ifStackTable (see rfc2233 [5]) must be used to link the channel entries to the corresponding physical layer entry to get the channel's configuration parameters. ADSL ifIndex ifTable Configuration Line Profile Table __________________________________________________________________ 1 i1 ADSL Line -- ---> Profile 1 j1 Fast Chan | | k1 Int Chan | | | ^ v | Profile 2 2 i2 ADSL Line ------->---- j2 Fast Chan | k2 Int Chan | | | Expires February 1999 [Page 13] INTERNET-DRAFT ADSL Line MIB August 7, 1998 | v x ix ADSL Line ------>-------> Profile X jx Fast Chan ----------------> kx Int Chan __________________________________________________________________ Figure 7: Use of Profiles in MODE-I The same is true for the alarm profile (not shown), although there is no requirement that its index (call it "m") be the same as the configuration profile. In this mode, profiles are allocated and deleted dynamically, and six objects: adslLineConfProfile, adslLineConfProfileIndexNext, adslLineConfProfileRowStatus, adlsLineAlarmProfile, adslLineAlarmConfProfileIndexNext, and adslLineAlarmConfProfileRowStatus are all used in conjunction with profiles. 7.4.2 MODE-II : Static Profiles Implementations with this mode will automatically create a profile one-for-one with each ADSL line physical entry with the profileIndex being the same as the ifIndex of the corresponding ADSL line entry ("ix"). In this mode, the Agent will not allow a Manager to create/delete profiles in this mode. Therefore, the adslLineConfProfile, adslLineConfProfileIndexNext, adslLineConfProfileRowStatus, adlsLineAlarmProfile, adslLineAlarmConfProfileIndexNext, and adslLineAlarmConfProfileRowStatus objects are not used in this mode as each line has a unique, fixed profile that is not shared with other lines. The figure below shows an example of this mode. In the example, ADSL lines '1', '2', and 'x' each have their own profiles. ADSL ifIndex ifTable Configuration Line Profile Table __________________________________________________________________ Expires February 1999 [Page 14] INTERNET-DRAFT ADSL Line MIB August 7, 1998 1 i1 ADSL Line ------------> Profile 1 j1 Fast Chan k1 Int Chan 2 i2 ADSL Line ------------> Profile 2 j2 Fast Chan k2 Int Chan x ix ADSL Line ------------> Profile X jx Fast Chan kx Int Chan __________________________________________________________________ Figure 8: User Profiles in MODE II 7.5 Traps These MIB-2 traps are required: coldStart / warmStart (per [6]) -- which are per agent (e.g., per DSLAM in such a device), and linkUp / linkDown (per [5]) -- which are per interface (i.e., ADSL line). Note: RFC 2233 [5] recommends that linkUp / linkDown only be used at a physical layer ifEntry, as discussed above. A linkDown trap is generated whenever any of Lof, Los, Lol, or Lpr occurs. At this operational point, a manager can use adslAtu*CurrStatus for additional detailed information. The corresponding linkUp trap is sent when all link failure conditions are cleared. The traps defined in this MIB are for initialization failure, rate change, and for the thresholds crossings associated with the following events: Lofs, Lols, Loss, Lprs, and ESs. Each threshold has its own enable/threshold value. When that value is 0, the trap is disabled. The objects adslAtu*CurrStatus indicate, through a bitmask, all outstanding error conditions or that the line is operational. Note that each object claims to represent the status of the modem at that end of the line. However, since the SNMP agent co-resides with the ATU-C, adslAturCurrStatus may be incomplete. For example, when there are errors on the line, the ATU-R may not be able to correctly report this condition. Therefore, not all conditions are included in adslAturCurrStatus. A threshold trap occurs whenever the corresponding current 15-minute interval error counter becomes equal to the threshold value. Since Expires February 1999 [Page 15] INTERNET-DRAFT ADSL Line MIB August 7, 1998 the current 15-minute counter are reset to 0 every 15 minutes, if the condition persists, the trap may recur as often as every 15 minutes. For example, to get a trap whenever a "loss of" event occurs (but at most once every 15 minutes), set the corresponding "Thresh15Min" to 1. The agent will generate a trap when the event originally occurs. Note that the NMS will get a linkDown trap, as well, if enabled. At the beginning of the next 15 minute interval, the counter is reset. When the first second goes by, the current interval bucket will be 1, which equals the threshold, and the trap will be sent again. The rate change trap is invoked when the transmit rate on a channel either increases by adsl(x)Thresh(y)RateDown or decreases by adsl(x)Thresh(y)RateDown. The trap is per direction:(x) == Atuc or Atur, and per channel: (y) == Fast or Interleave. In other words, the trap is sent whenever the rate changes in either direction on either channel and: CurrTxRate >= PrevTxRate plus ThreshRateUp or CurrTxRate <= PrevTxRate minus ThreshRateDown No trap is sent on initialization. It can be disabled by setting the Up (and/or) Down threshold rates to 0. The PrevTxRate object is set to the current value at initialization and when a trap is sent. Thus rate changes are cumulative until the total change exceeds the threshold. 8. Conformance and Compliance See ASN.1 within. 9. Definitions ADSL-LINE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32, NOTIFICATION-TYPE, Integer32, OBJECT-IDENTITY, transmission FROM SNMPv2-SMI Expires February 1999 [Page 16] INTERNET-DRAFT ADSL Line MIB August 7, 1998 RowStatus, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ifIndex FROM IF-MIB -- rfc2233 Utf8String FROM SYSAPPL-MIB -- rfc2287 ; AdslLineProfileType ::= INTEGER adslMIB MODULE-IDENTITY LAST-UPDATED "9808070000Z" ORGANIZATION "IETF ADSL-MIB WG" CONTACT-INFO " Gregory Bathrick AG Communication Systems 2500 W Utopia Rd. Phoenix, AZ 85027 USA Tel: +1 602-582-7679 Fax: +1 602-582-7697 E-mail: bathricg@agcs.com John Burgess Predictive Systems, Inc. 25A Vreeland Rd. Florham Park, NJ 07932 USA Tel: +1 973-301-5610 Fax: +1 973-301-5699 E-mail: jtburgess@predictive.com " DESCRIPTION "The MIB module defining objects for the management of a pair of ADSL modems at each end of the ADSL line. Each such Line is indexed by ifIndex and appears as an interface on a central DSLAM (Digital Subscriber Line Access Mux.) Attributes on the ATUR are proxied by the DSLAM. ADSL lines may support optional Fast or Interleaved channels. If these are supported, additional entries corresponding to the supported channels must be created in the ifTable. Thus an ADSL line that supports both channels will have three entries in the ifTable, one for each physical, fast, and interleaved, whose ifType values are equal to adsl(94), fast(125), and interleaved(124), respectively. The ifStackTable is used to link the entries together. Expires February 1999 [Page 17] INTERNET-DRAFT ADSL Line MIB August 7, 1998 Naming Conventions: Atuc -- (ATUC) modem at near (Central) end of line Atur -- (ATUR) modem at Remote end of line Curr -- Current Prev -- Previous Atn -- Attenuation ES -- Errored Second. LCS -- Line Code Specific Lof -- Loss of Frame Lol -- Loss of Link Los -- Loss of Signal Lpr -- Loss of Power xxxs-- interval of Seconds in which xxx occurs (e.g., xxx=Lof, Los, Lpr) Max -- Maximum Mgn -- Margin Min -- Minimum Psd -- Power Spectral Density Snr -- Signal to Noise Ratio Tx -- Transmit Blks-- Blocks, a data unit, see adslAtuXChanCrcBlockLength " REVISION "9808070000Z" DESCRIPTION "Changes taken at the March 98 ADSL WG meeting: - Added Conformance Statement - SNMPv3 comformance - RFC-2233 comformance Comments from Technical Advisors, Wijnen and Tesink: - DisplayString -> UTF-8 String - minimized # of mandatory performance counts - Corrected Syntax of current status objects. - Corrected use of SNMP SMI. Lessons learned through implementation of MIB (ADSLF TR006): - clarified definition of channel block size, SNR Interleave Delay, Attenuation, and Output power. - corrected UNITS and SYNTAX of adsl rate objects, Version#, VendorID. - added missing line activation objects. General editorial cleanup. Added Security Statement (Dave Allan) " REVISION "9808071200Z" Expires February 1999 [Page 18] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "General editorial cleanup. " ::= { transmission 94 } adslLineMib OBJECT IDENTIFIER ::= { adslMIB 1 } adslMibObjects OBJECT IDENTIFIER ::= { adslLineMib 1 } adslLineTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table includes common attributes describing both ends of the line. It is required for all ADSL physical interfaces. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 1 } adslLineEntry OBJECT-TYPE SYNTAX AdslLineEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslLineTable." INDEX { ifIndex } ::= { adslLineTable 1 } AdslLineEntry ::= SEQUENCE { adslLineCoding INTEGER, adslLineType INTEGER, adslLineSpecific OBJECT IDENTIFIER, adslLineConfProfile AdslLineProfileType, adslLineAlarmConfProfile AdslLineProfileType } adslLineCoding OBJECT-TYPE SYNTAX INTEGER { other (1), dmt (2), -- Discrete MultiTone cap (3), -- Carrierless Amplitude & Phase modulation qam (4) -- Quadrature Amplitude Modulation } MAX-ACCESS read-only STATUS current Expires February 1999 [Page 19] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "Specifies the ADSL coding type used on this line. Other types may be added in the future." ::= { adslLineEntry 1 } adslLineType OBJECT-TYPE SYNTAX INTEGER { noChannel (1), -- no channels exist fastOnly (2), -- fast channel exists only interleavedOnly (3), -- interleaved channel exists -- only fastOrInterleaved (4),-- either fast or interleaved -- channels can exist, but -- only one at any time fastAndInterleaved (5)-- both fast or interleaved -- channels exist } MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of ADSL physical line entity that exists, by defining whether and how the line is channelized. If the line is channelized, the value will be other than noChannel(1). This object defines which channel type(s) are supported. In the case that the line is channelized, the manager can use the ifStackTable to determine the ifIndex for the associated channel(s)." ::= { adslLineEntry 2 } adslLineSpecific OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "OID instance in vendor-specific MIB. The Instance may be used to determine shelf/slot/port of the ATUC interface in a DSLAM." ::= { adslLineEntry 3 } adslLineConfProfile OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Configuration Profile Table, Expires February 1999 [Page 20] INTERNET-DRAFT ADSL Line MIB August 7, 1998 (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. In the case which the configuration profile has not been set, the value will be set to '0'. If the implementator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchObject upon SNMP request." ::= { adslLineEntry 4 } adslLineAlarmConfProfile OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS read-write STATUS current DESCRIPTION "The value of this object identifies the row in the ADSL Line Alarm Configuration Profile Table, (adslLineAlarmConfProfileTable), which applies to this ADSL line, and channels if applicable. In the case which the configuration profile has not been set, the value will be set to '0'. If the implementator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchObject upon SNMP request." ::= { adslLineEntry 5 } adslAtucPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. Each row contains the Physical Layer Parameters table for that ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 2 } adslAtucPhysEntry OBJECT-TYPE SYNTAX AdslAtucPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucPhysTable." INDEX { ifIndex } ::= { adslAtucPhysTable 1 } Expires February 1999 [Page 21] INTERNET-DRAFT ADSL Line MIB August 7, 1998 AdslAtucPhysEntry ::= SEQUENCE { adslAtucInvSerialNumber Utf8String, adslAtucInvVendorID Utf8String, adslAtucInvVersionNumber Utf8String, adslAtucCurrSnrMgn Integer32, adslAtucCurrAtn Integer32, adslAtucCurrStatus BITS, adslAtucCurrOutputPwr Integer32, adslAtucCurrAttainableRate Integer32 } -- inventory group -- -- These items should describe the lowest level identifiable -- component, be it a stand-alone modem, a card in a rack, -- a child-board, etc. -- adslAtucInvSerialNumber OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor specific string that identifies the vendor equipment." ::= { adslAtucPhysEntry 1 } adslAtucInvVendorID OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID assigned by T1E1.413 according to its Annex D.[10]" ::= { adslAtucPhysEntry 2 } adslAtucInvVersionNumber OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor specific version number sent by this ATU as part of the initialization messages." ::= { adslAtucPhysEntry 3 } -- current status group -- adslAtucCurrSnrMgn OBJECT-TYPE Expires February 1999 [Page 22] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX Integer32(0..310) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal in tenth dB." ::= { adslAtucPhysEntry 4 } adslAtucCurrAtn OBJECT-TYPE SYNTAX Integer32(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. This value is determined in accordance with T1.413[10]." ::= { adslAtucPhysEntry 5 } adslAtucCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfLink(4), lossOfSignalQuality(5), dataInitFailure(6), configInitFailure(7), protocolInitFailure(8), noPeerAtuPresent(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status indicates current state ATUC line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUC failure due to not receiving valid frame. 2 lossOfSignal ATUC failure due to not receiving signal. Expires February 1999 [Page 23] INTERNET-DRAFT ADSL Line MIB August 7, 1998 3 lossOfPower ATUC failure due to loss of power. Note: the Agent may still function. 4 lossOfLink ATUC failure due to inability to link with ATUR. 5 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 6 dataInitFailure ATUC failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure ATUC failure during initialization due to peer ATU not able to support requested configuration 8 protocolInitFailure ATUC failure during initialization due to incompatible protocol used by the peer ATU. 9 noPeerAtuPresent ATUC failure during initialization due to no activation sequence detected from peer ATU. This is intended to supplement ifOperStatus." ::= { adslAtucPhysEntry 6 } adslAtucCurrOutputPwr OBJECT-TYPE SYNTAX Integer32(0..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU. This is the measurement that was reported during the last activation sequence." ::= { adslAtucPhysEntry 7 } Expires February 1999 [Page 24] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucCurrAttainableRate OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate." ::= { adslAtucPhysEntry 8 } adslAturPhysTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR Each row contains the Physical Layer Parameters table for that ATUR. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 3 } adslAturPhysEntry OBJECT-TYPE SYNTAX AdslAturPhysEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturPhysTable." INDEX { ifIndex } ::= { adslAturPhysTable 1 } AdslAturPhysEntry ::= SEQUENCE { adslAturInvSerialNumber Utf8String, adslAturInvVendorID Utf8String, adslAturInvVersionNumber Utf8String, adslAturCurrSnrMgn Integer32, adslAturCurrAtn Integer32, adslAturCurrStatus BITS, adslAturCurrOutputPwr Integer32, adslAturCurrAttainableRate Integer32 } -- inventory group -- adslAturInvSerialNumber OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-only STATUS current Expires February 1999 [Page 25] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "Vendor specific string that identifies the vendor equipment." ::= { adslAturPhysEntry 1 } adslAturInvVendorID OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor ID assigned by T1E1.413 according to its Annex D." ::= { adslAturPhysEntry 2 } adslAturInvVersionNumber OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor specific version number sent by this ATU as part of the initialization messages." ::= { adslAturPhysEntry 3 } -- current status group -- adslAturCurrSnrMgn OBJECT-TYPE SYNTAX Integer32(0..310) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Noise Margin as seen by this ATU with respect to its received signal. This value is determined in accordance with T1.413 [10]." ::= { adslAturPhysEntry 4 } adslAturCurrAtn OBJECT-TYPE SYNTAX Integer32(0..630) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. This value is determined in accordance with T1.413[10]." ::= { adslAturPhysEntry 5 } Expires February 1999 [Page 26] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAturCurrStatus OBJECT-TYPE SYNTAX BITS { noDefect(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), lossOfSignalQuality(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status indicates current state ATUR line. This is a bit-map of possible conditions. Due to the isolation of the ATUR when line problems occur, many state conditions like loss of power, loss of quality signal, and initialization errors, can not be determined. While trouble shooting ATUR, also use object, adslAtucCurrStatus. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming ATUR failure due to not receiving valid frame 2 lossOfSignal ATUR failure due to not receiving signal 3 lossOfPower ATUR failure due to loss of power 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus." ::= { adslAturPhysEntry 6 } adslAturCurrOutputPwr OBJECT-TYPE SYNTAX Integer32(0..310) UNITS "tenth dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "Measured total output power transmitted by this ATU. This is the measurement that was reported during Expires February 1999 [Page 27] INTERNET-DRAFT ADSL Line MIB August 7, 1998 the last activation sequence." ::= { adslAturPhysEntry 7 } adslAturCurrAttainableRate OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate." ::= { adslAturPhysEntry 8 } adslAtucChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 4 } adslAtucChanEntry OBJECT-TYPE SYNTAX AdslAtucChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucChanTable." INDEX { ifIndex } ::= { adslAtucChanTable 1 } AdslAtucChanEntry ::= SEQUENCE { adslAtucChanInterleaveDelay Gauge32, adslAtucChanCurrTxRate Gauge32, adslAtucChanPrevTxRate Gauge32, adslAtucChanCrcBlockLength Gauge32 } -- current group -- adslAtucChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milli-seconds" MAX-ACCESS read-only Expires February 1999 [Page 28] INTERNET-DRAFT ADSL Line MIB August 7, 1998 STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject." ::= { adslAtucChanEntry 1 } adslAtucChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAtucChanEntry 2 } adslAtucChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The rate at the time of the last adslAtucRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAtucThresh(*)RateDown or less than adslAtucThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAtucChanEntry 3 } adslAtucChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 UNITS "byte" MAX-ACCESS read-only Expires February 1999 [Page 29] INTERNET-DRAFT ADSL Line MIB August 7, 1998 STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information." ::= { adslAtucChanEntry 4 } adslAturChanTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 5 } adslAturChanEntry OBJECT-TYPE SYNTAX AdslAturChanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturChanTable." INDEX { ifIndex } ::= { adslAturChanTable 1 } AdslAturChanEntry ::= SEQUENCE { adslAturChanInterleaveDelay Gauge32, adslAturChanCurrTxRate Gauge32, adslAturChanPrevTxRate Gauge32, adslAturChanCrcBlockLength Gauge32 } -- current group -- adslAturChanInterleaveDelay OBJECT-TYPE SYNTAX Gauge32 UNITS "milli-seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input Expires February 1999 [Page 30] INTERNET-DRAFT ADSL Line MIB August 7, 1998 bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency. In the case where the ifType is Fast(125), use noSuchObject." ::= { adslAturChanEntry 1 } adslAturChanCurrTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "Actual transmit rate on this channel." ::= { adslAturChanEntry 2 } adslAturChanPrevTxRate OBJECT-TYPE SYNTAX Gauge32 UNITS "bps" MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The rate at the time of the last adslAturRateChangeTrap event. It is also set at initialization to prevent a trap being sent. Rate changes less than adslAturThresh(*)RateDown or less than adslAturThresh(*)RateUp will not cause a trap or cause this object to change. (*) == Fast or Interleave. See AdslLineAlarmConfProfileEntry." ::= { adslAturChanEntry 3 } adslAturChanCrcBlockLength OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the length of the channel data-block on which the CRC operates. Refer to Line Code Specific MIBs, [11] and [12] for more information." ::= { adslAturChanEntry 4 } Expires February 1999 [Page 31] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 6 } adslAtucPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucPerfDataTable." INDEX { ifIndex } ::= { adslAtucPerfDataTable 1 } AdslAtucPerfDataEntry ::= SEQUENCE { adslAtucPerfLofs Counter32, adslAtucPerfLoss Counter32, adslAtucPerfLols Counter32, adslAtucPerfLprs Counter32, adslAtucPerfESs Counter32, adslAtucPerfInits Counter32, adslAtucPerfValidIntervals INTEGER, adslAtucPerfInvalidIntervals INTEGER, adslAtucPerfCurr15MinTimeElapsed INTEGER, adslAtucPerfCurr15MinLofs Gauge32, adslAtucPerfCurr15MinLoss Gauge32, adslAtucPerfCurr15MinLols Gauge32, adslAtucPerfCurr15MinLprs Gauge32, adslAtucPerfCurr15MinESs Gauge32, adslAtucPerfCurr15MinInits Gauge32, adslAtucPerfCurr1DayTimeElapsed INTEGER, adslAtucPerfCurr1DayLofs Gauge32, adslAtucPerfCurr1DayLoss Gauge32, adslAtucPerfCurr1DayLols Gauge32, adslAtucPerfCurr1DayLprs Gauge32, adslAtucPerfCurr1DayESs Gauge32, adslAtucPerfCurr1DayInits Gauge32, adslAtucPerfPrev1DayMoniSecs INTEGER, adslAtucPerfPrev1DayLofs Gauge32, adslAtucPerfPrev1DayLoss Gauge32, adslAtucPerfPrev1DayLols Gauge32, adslAtucPerfPrev1DayLprs Gauge32, adslAtucPerfPrev1DayESs Gauge32, Expires February 1999 [Page 32] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucPerfPrev1DayInits Gauge32 } -- Event Counters -- -- Also see adslAtucIntervalTable for 15 minute interval -- elapsed counters. -- adslAtucPerfLofs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since agent reset." ::= { adslAtucPerfDataEntry 1 } adslAtucPerfLoss OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAtucPerfDataEntry 2 } adslAtucPerfLols OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Link failures since agent reset." ::= { adslAtucPerfDataEntry 3 } adslAtucPerfLprs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAtucPerfDataEntry 4 } adslAtucPerfESs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current Expires February 1999 [Page 33] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 5 } adslAtucPerfInits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts since agent reset. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 6 } -- general 15 min interval information -- adslAtucPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAtucInterval Table for which valid data has been stored. This value will be equal to the maximum # of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAtucPerfDataEntry 7 } adslAtucPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 15 minute intervals in which no valid data is available." ::= { adslAtucPerfDataEntry 8 } -- 15 min current performance group -- adslAtucPerfCurr15MinTimeElapsed OBJECT-TYPE Expires February 1999 [Page 34] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAtucPerfDataEntry 9 } adslAtucPerfCurr15MinLofs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAtucPerfDataEntry 10 } adslAtucPerfCurr15MinLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAtucPerfDataEntry 11 } adslAtucPerfCurr15MinLols OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Link." ::= { adslAtucPerfDataEntry 12 } adslAtucPerfCurr15MinLprs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAtucPerfDataEntry 13 } Expires February 1999 [Page 35] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucPerfCurr15MinESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 14 } adslAtucPerfCurr15MinInits OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the current 15 minute interval. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 15 } -- 1-day current and previous performance group -- adslAtucPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAtucPerfDataEntry 16 } adslAtucPerfCurr1DayLofs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 17 } adslAtucPerfCurr1DayLoss OBJECT-TYPE SYNTAX Gauge32 Expires February 1999 [Page 36] INTERNET-DRAFT ADSL Line MIB August 7, 1998 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 18 } adslAtucPerfCurr1DayLols OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Link during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 19 } adslAtucPerfCurr1DayLprs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAtucPerfCurr1DayTimeElapsed." ::= { adslAtucPerfDataEntry 20 } adslAtucPerfCurr1DayESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAtucPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 21 } adslAtucPerfCurr1DayInits OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current Expires February 1999 [Page 37] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "Count of the line initialization attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 22 } adslAtucPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring data can not be collected for any reason. Typically Elapsed 1-day time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAtucPerfDataEntry 23 } adslAtucPerfPrev1DayLofs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 24 } adslAtucPerfPrev1DayLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 25 } adslAtucPerfPrev1DayLols OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only Expires February 1999 [Page 38] INTERNET-DRAFT ADSL Line MIB August 7, 1998 STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 26 } adslAtucPerfPrev1DayLprs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period." ::= { adslAtucPerfDataEntry 27 } adslAtucPerfPrev1DayESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucPerfDataEntry 28 } adslAtucPerfPrev1DayInits OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts in the most recent previous 1-day period. Includes both successful and failed attempts." ::= { adslAtucPerfDataEntry 29 } adslAturPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR. ADSL physical interfaces are Expires February 1999 [Page 39] INTERNET-DRAFT ADSL Line MIB August 7, 1998 those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 7 } adslAturPerfDataEntry OBJECT-TYPE SYNTAX AdslAturPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturPerfDataTable." INDEX { ifIndex } ::= { adslAturPerfDataTable 1 } AdslAturPerfDataEntry ::= SEQUENCE { adslAturPerfLofs Counter32, adslAturPerfLoss Counter32, adslAturPerfLprs Counter32, adslAturPerfESs Counter32, adslAturPerfValidIntervals INTEGER, adslAturPerfInvalidIntervals INTEGER, adslAturPerfCurr15MinTimeElapsed INTEGER, adslAturPerfCurr15MinLofs Gauge32, adslAturPerfCurr15MinLoss Gauge32, adslAturPerfCurr15MinLprs Gauge32, adslAturPerfCurr15MinESs Gauge32, adslAturPerfCurr1DayTimeElapsed INTEGER, adslAturPerfCurr1DayLofs Gauge32, adslAturPerfCurr1DayLoss Gauge32, adslAturPerfCurr1DayLprs Gauge32, adslAturPerfCurr1DayESs Gauge32, adslAturPerfPrev1DayMoniSecs INTEGER, adslAturPerfPrev1DayLofs Gauge32, adslAturPerfPrev1DayLoss Gauge32, adslAturPerfPrev1DayLprs Gauge32, adslAturPerfPrev1DayESs Gauge32 } -- Event (Raw) Counters -- -- Also see adslAturIntervalTable for 15 minute interval -- elapsed counters. -- adslAturPerfLofs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Framing failures since Expires February 1999 [Page 40] INTERNET-DRAFT ADSL Line MIB August 7, 1998 agent reset." ::= { adslAturPerfDataEntry 1 } adslAturPerfLoss OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Signal failures since agent reset." ::= { adslAturPerfDataEntry 2 } adslAturPerfLprs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Loss of Power failures since agent reset." ::= { adslAturPerfDataEntry 3 } adslAturPerfESs OBJECT-TYPE SYNTAX Counter32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of Errored Seconds since agent reset. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 4 } -- general 15 min interval information -- adslAturPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAturInterval Table for which valid data has been stored. This value will be equal to the maximum # of intervals that are kept (n) unless the device was brought online within the last (nx15) min. In the case where the agent is a proxy, it is possible Expires February 1999 [Page 41] INTERNET-DRAFT ADSL Line MIB August 7, 1998 that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAturPerfDataEntry 5 } adslAturPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 15 minute intervals in which no valid data is available." ::= { adslAturPerfDataEntry 6 } -- 15 min current performance group -- adslAturPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAturPerfDataEntry 7 } adslAturPerfCurr15MinLofs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Framing." ::= { adslAturPerfDataEntry 8 } adslAturPerfCurr15MinLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Signal." ::= { adslAturPerfDataEntry 9 } adslAturPerfCurr15MinLprs OBJECT-TYPE SYNTAX Gauge32 Expires February 1999 [Page 42] INTERNET-DRAFT ADSL Line MIB August 7, 1998 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the current 15 minute interval when there was Loss of Power." ::= { adslAturPerfDataEntry 10 } adslAturPerfCurr15MinESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the current 15 minute interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAturPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAturPerfDataEntry 12 } adslAturPerfCurr1DayLofs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Framing during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 13 } adslAturPerfCurr1DayLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only Expires February 1999 [Page 43] INTERNET-DRAFT ADSL Line MIB August 7, 1998 STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Signal during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 14 } adslAturPerfCurr1DayLprs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the number of seconds when there was Loss of Power during the current day as measured by adslAturPerfCurr1DayTimeElapsed." ::= { adslAturPerfDataEntry 15 } adslAturPerfCurr1DayESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds during the current day as measured by adslAturPerfCurr1DayTimeElapsed. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 16 } adslAturPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring data can not be collected for any reason. Typically Elapsed 1-day time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAturPerfDataEntry 17 } adslAturPerfPrev1DayLofs OBJECT-TYPE Expires February 1999 [Page 44] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 18 } adslAturPerfPrev1DayLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 19 } adslAturPerfPrev1DayLprs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power within the most recent previous 1-day period." ::= { adslAturPerfDataEntry 20 } adslAturPerfPrev1DayESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds within the most recent previous 1-day period. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturPerfDataEntry 21 } adslAtucIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current Expires February 1999 [Page 45] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "This table provides one row for each ATUC performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 8 } adslAtucIntervalEntry OBJECT-TYPE SYNTAX AdslAtucIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucIntervalNumber } ::= { adslAtucIntervalTable 1 } AdslAtucIntervalEntry ::= SEQUENCE { adslAtucIntervalNumber INTEGER, adslAtucIntervalLofs Gauge32, adslAtucIntervalLoss Gauge32, adslAtucIntervalLols Gauge32, adslAtucIntervalLprs Gauge32, adslAtucIntervalESs Gauge32, adslAtucIntervalInits Gauge32, adslAtucIntervalValidData TruthValue } adslAtucIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Intervals 2..96 are optional." ::= { adslAtucIntervalEntry 1 } adslAtucIntervalLofs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAtucIntervalEntry 2 } adslAtucIntervalLoss OBJECT-TYPE Expires February 1999 [Page 46] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAtucIntervalEntry 3 } adslAtucIntervalLols OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Link." ::= { adslAtucIntervalEntry 4 } adslAtucIntervalLprs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAtucIntervalEntry 5 } adslAtucIntervalESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAtucIntervalEntry 6 } adslAtucIntervalInits OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of the line initialization attempts during the interval. Includes both successful Expires February 1999 [Page 47] INTERNET-DRAFT ADSL Line MIB August 7, 1998 and failed attempts." ::= { adslAtucIntervalEntry 7 } adslAtucIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if there is valid data for this interval." ::= { adslAtucIntervalEntry 8 } adslAturIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR performance data collection interval. ADSL physical interfaces are those ifEntries where ifType is equal to adsl(94)." ::= { adslMibObjects 9 } adslAturIntervalEntry OBJECT-TYPE SYNTAX AdslAturIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturIntervalNumber } ::= { adslAturIntervalTable 1 } AdslAturIntervalEntry ::= SEQUENCE { adslAturIntervalNumber INTEGER, adslAturIntervalLofs Gauge32, adslAturIntervalLoss Gauge32, adslAturIntervalLprs Gauge32, adslAturIntervalESs Gauge32, adslAturIntervalValidData TruthValue } adslAturIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 Expires February 1999 [Page 48] INTERNET-DRAFT ADSL Line MIB August 7, 1998 hours ago. Intervals 2..96 are optional." ::= { adslAturIntervalEntry 1 } adslAturIntervalLofs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Framing." ::= { adslAturIntervalEntry 2 } adslAturIntervalLoss OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Signal." ::= { adslAturIntervalEntry 3 } adslAturIntervalLprs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of seconds in the interval when there was Loss of Power." ::= { adslAturIntervalEntry 4 } adslAturIntervalESs OBJECT-TYPE SYNTAX Gauge32 UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects." ::= { adslAturIntervalEntry 5 } adslAturIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only Expires February 1999 [Page 49] INTERNET-DRAFT ADSL Line MIB August 7, 1998 STATUS current DESCRIPTION "This object indicates if there is valid data for this interval." ::= { adslAturIntervalEntry 6 } adslAtucChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 10 } adslAtucChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAtucChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAtucChanPerfDataTable." INDEX { ifIndex } ::= { adslAtucChanPerfDataTable 1 } AdslAtucChanPerfDataEntry ::= SEQUENCE { adslAtucChanReceivedBlks Counter32, adslAtucChanTransmittedBlks Counter32, adslAtucChanCorrectedBlks Counter32, adslAtucChanUncorrectBlks Counter32, adslAtucChanPerfValidIntervals INTEGER, adslAtucChanPerfInvalidIntervals INTEGER, adslAtucChanPerfCurr15MinTimeElapsed INTEGER, adslAtucChanPerfCurr15MinReceivedBlks Gauge32, adslAtucChanPerfCurr15MinTransmittedBlks Gauge32, adslAtucChanPerfCurr15MinCorrectedBlks Gauge32, adslAtucChanPerfCurr15MinUncorrectBlks Gauge32, adslAtucChanPerfCurr1DayTimeElapsed INTEGER, adslAtucChanPerfCurr1DayReceivedBlks Gauge32, adslAtucChanPerfCurr1DayTransmittedBlks Gauge32, adslAtucChanPerfCurr1DayCorrectedBlks Gauge32, adslAtucChanPerfCurr1DayUncorrectBlks Gauge32, adslAtucChanPerfPrev1DayMoniSecs INTEGER, adslAtucChanPerfPrev1DayReceivedBlks Gauge32, adslAtucChanPerfPrev1DayTransmittedBlks Gauge32, adslAtucChanPerfPrev1DayCorrectedBlks Gauge32, Expires February 1999 [Page 50] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucChanPerfPrev1DayUncorrectBlks Gauge32 } -- performance group -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAtucChanCrcBlockLength for more information. -- adslAtucChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 1 } adslAtucChanTransmittedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAtucChanPerfDataEntry 2 } adslAtucChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAtucChanPerfDataEntry 3 } adslAtucChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAtucChanPerfDataEntry 4 } -- general 15 min interval information -- adslAtucChanPerfValidIntervals OBJECT-TYPE Expires February 1999 [Page 51] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAtucChanIntervalTable Table for which valid data has been stored. This value will be equal to the max number of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAtucChanPerfDataEntry 5 } adslAtucChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of 15 minute intervals in which no valid data is available." ::= { adslAtucChanPerfDataEntry 6 } -- 15 min current performance group -- adslAtucChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAtucChanPerfDataEntry 7 } adslAtucChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 8 } adslAtucChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 Expires February 1999 [Page 52] INTERNET-DRAFT ADSL Line MIB August 7, 1998 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 9 } adslAtucChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 10 } adslAtucChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAtucChanPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAtucChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAtucChanPerfDataEntry 12 } adslAtucChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 13 } Expires February 1999 [Page 53] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 14 } adslAtucChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 15 } adslAtucChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed." ::= { adslAtucChanPerfDataEntry 16 } adslAtucChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be collected for any reason. Typically Elapsed 1-day time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAtucChanPerfDataEntry 17 } adslAtucChanPerfPrev1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 Expires February 1999 [Page 54] INTERNET-DRAFT ADSL Line MIB August 7, 1998 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 18 } adslAtucChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 19 } adslAtucChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 20 } adslAtucChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period." ::= { adslAtucChanPerfDataEntry 21 } adslAturChanPerfDataTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 11 } Expires February 1999 [Page 55] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAturChanPerfDataEntry OBJECT-TYPE SYNTAX AdslAturChanPerfDataEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in adslAturChanPerfDataTable." INDEX { ifIndex } ::= { adslAturChanPerfDataTable 1 } AdslAturChanPerfDataEntry ::= SEQUENCE { adslAturChanReceivedBlks Counter32, adslAturChanTransmittedBlks Counter32, adslAturChanCorrectedBlks Counter32, adslAturChanUncorrectBlks Counter32, adslAturChanPerfValidIntervals INTEGER, adslAturChanPerfInvalidIntervals INTEGER, adslAturChanPerfCurr15MinTimeElapsed INTEGER, adslAturChanPerfCurr15MinReceivedBlks Gauge32, adslAturChanPerfCurr15MinTransmittedBlks Gauge32, adslAturChanPerfCurr15MinCorrectedBlks Gauge32, adslAturChanPerfCurr15MinUncorrectBlks Gauge32, adslAturChanPerfCurr1DayTimeElapsed INTEGER, adslAturChanPerfCurr1DayReceivedBlks Gauge32, adslAturChanPerfCurr1DayTransmittedBlks Gauge32, adslAturChanPerfCurr1DayCorrectedBlks Gauge32, adslAturChanPerfCurr1DayUncorrectBlks Gauge32, adslAturChanPerfPrev1DayMoniSecs INTEGER, adslAturChanPerfPrev1DayReceivedBlks Gauge32, adslAturChanPerfPrev1DayTransmittedBlks Gauge32, adslAturChanPerfPrev1DayCorrectedBlks Gauge32, adslAturChanPerfPrev1DayUncorrectBlks Gauge32 } -- performance group -- -- Note: block is intended to be the length of the channel -- data-block on which the CRC operates. See -- adslAturChanCrcBlockLength for more information. -- adslAturChanReceivedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel since agent reset." ::= { adslAturChanPerfDataEntry 1 } adslAturChanTransmittedBlks OBJECT-TYPE Expires February 1999 [Page 56] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel since agent reset." ::= { adslAturChanPerfDataEntry 2 } adslAturChanCorrectedBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data." ::= { adslAturChanPerfDataEntry 3 } adslAturChanUncorrectBlks OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors since agent reset." ::= { adslAturChanPerfDataEntry 4 } -- general 15 min interval information -- adslAturChanPerfValidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only STATUS current DESCRIPTION "Number of previous 15-minute intervals in the adslAturChanIntervalTable Table for which valid data has been stored. This value will be equal to the max # of intervals that are kept (n) unless the device was brought online within the last (nx15) minutes. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this interval is the maximum interval for which valid data is available." ::= { adslAturChanPerfDataEntry 5 } adslAturChanPerfInvalidIntervals OBJECT-TYPE SYNTAX INTEGER(0..96) MAX-ACCESS read-only Expires February 1999 [Page 57] INTERNET-DRAFT ADSL Line MIB August 7, 1998 STATUS current DESCRIPTION "The number of 15 minute intervals in which no valid data is available." ::= { adslAturChanPerfDataEntry 6 } -- 15 min current performance group -- adslAturChanPerfCurr15MinTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..899) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Total elapsed seconds in this interval. A full interval is 900 seconds." ::= { adslAturChanPerfDataEntry 7 } adslAturChanPerfCurr15MinReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 8 } adslAturChanPerfCurr15MinTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 9 } adslAturChanPerfCurr15MinCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 10 } adslAturChanPerfCurr15MinUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 Expires February 1999 [Page 58] INTERNET-DRAFT ADSL Line MIB August 7, 1998 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval." ::= { adslAturChanPerfDataEntry 11 } -- 1-day current and previous performance group -- adslAturChanPerfCurr1DayTimeElapsed OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "Number of seconds that have elapsed since the beginning of the current 1-day interval." ::= { adslAturChanPerfDataEntry 12 } adslAturChanPerfCurr1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 13 } adslAturChanPerfCurr1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 14 } adslAturChanPerfCurr1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during the current day as Expires February 1999 [Page 59] INTERNET-DRAFT ADSL Line MIB August 7, 1998 measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 15 } adslAturChanPerfCurr1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed." ::= { adslAturChanPerfDataEntry 16 } adslAturChanPerfPrev1DayMoniSecs OBJECT-TYPE SYNTAX INTEGER(0..86399) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be collected for any reason. Typically Elapsed 1-day time will be copied into Monitored Seconds when the 1-day roll-over occurs." ::= { adslAturChanPerfDataEntry 17 } adslAturChanPerfPrev1DayReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 18 } adslAturChanPerfPrev1DayTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 19 } Expires February 1999 [Page 60] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAturChanPerfPrev1DayCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 20 } adslAturChanPerfPrev1DayUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel within the most recent previous 1-day period." ::= { adslAturChanPerfDataEntry 21 } adslAtucChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUC channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 12 } adslAtucChanIntervalEntry OBJECT-TYPE SYNTAX AdslAtucChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAtucIntervalTable." INDEX { ifIndex, adslAtucChanIntervalNumber } ::= { adslAtucChanIntervalTable 1 } AdslAtucChanIntervalEntry ::= SEQUENCE { adslAtucChanIntervalNumber INTEGER, adslAtucChanIntervalReceivedBlks Gauge32, adslAtucChanIntervalTransmittedBlks Gauge32, adslAtucChanIntervalCorrectedBlks Gauge32, adslAtucChanIntervalUncorrectBlks Gauge32, adslAtucChanIntervalValidData TruthValue Expires February 1999 [Page 61] INTERNET-DRAFT ADSL Line MIB August 7, 1998 } adslAtucChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional." ::= { adslAtucChanIntervalEntry 1 } adslAtucChanIntervalReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAtucChanIntervalEntry 2 } adslAtucChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAtucChanIntervalEntry 3 } adslAtucChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAtucChanIntervalEntry 4 } adslAtucChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAtucChanIntervalEntry 5 } adslAtucChanIntervalValidData OBJECT-TYPE Expires February 1999 [Page 62] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if there is valid data for this interval." ::= { adslAtucChanIntervalEntry 6 } adslAturChanIntervalTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides one row for each ATUR channel's performance data collection interval. ADSL channel interfaces are those ifEntries where ifType is equal to adslInterleave(124) or adslFast(125)." ::= { adslMibObjects 13 } adslAturChanIntervalEntry OBJECT-TYPE SYNTAX AdslAturChanIntervalEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the adslAturIntervalTable." INDEX { ifIndex, adslAturChanIntervalNumber } ::= { adslAturChanIntervalTable 1 } AdslAturChanIntervalEntry ::= SEQUENCE { adslAturChanIntervalNumber INTEGER, adslAturChanIntervalReceivedBlks Gauge32, adslAturChanIntervalTransmittedBlks Gauge32, adslAturChanIntervalCorrectedBlks Gauge32, adslAturChanIntervalUncorrectBlks Gauge32, adslAturChanIntervalValidData TruthValue } adslAturChanIntervalNumber OBJECT-TYPE SYNTAX INTEGER(1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional." ::= { adslAturChanIntervalEntry 1 } Expires February 1999 [Page 63] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAturChanIntervalReceivedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks received on this channel during this interval." ::= { adslAturChanIntervalEntry 2 } adslAturChanIntervalTransmittedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all encoded blocks transmitted on this channel during this interval." ::= { adslAturChanIntervalEntry 3 } adslAturChanIntervalCorrectedBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with errors that were corrected on this channel during this interval." ::= { adslAturChanIntervalEntry 4 } adslAturChanIntervalUncorrectBlks OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of all blocks received with uncorrectable errors on this channel during this interval." ::= { adslAturChanIntervalEntry 5 } adslAturChanIntervalValidData OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates if there is valid data for this interval." ::= { adslAturChanIntervalEntry 6 } -- Profile Group -- Expires February 1999 [Page 64] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslLineConfProfileIndexNext OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for adslLineConfProfileIndex when creating entries in the adslLineConfProfileTable. The value '0' indicates that no unassigned entries are available. To obtain the adslLineConfProfileIndexNext value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. If the implementator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchObject upon SNMP request." ::= { adslMibObjects 14} adslLineConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the ADSL line." ::= { adslMibObjects 15} adslLineConfProfileEntry OBJECT-TYPE SYNTAX AdslLineConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. A profile is created in one step with all necessary parameter values and adslLineProfileRowStatus set to createAndGo. This RowStatus object is also used to delete destroy profiles." INDEX { adslLineConfProfileIndex} ::= { adslLineConfProfileTable 1} AdslLineConfProfileEntry ::= Expires February 1999 [Page 65] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SEQUENCE { adslLineConfProfileIndex AdslLineProfileType, adslAtucConfRateMode INTEGER, adslAtucConfRateChanRatio INTEGER, adslAtucConfTargetSnrMgn INTEGER, adslAtucConfMaxSnrMgn INTEGER, adslAtucConfMinSnrMgn INTEGER, adslAtucConfDownshiftSnrMgn INTEGER, adslAtucConfUpshiftSnrMgn INTEGER, adslAtucConfMinUpshiftTime INTEGER, adslAtucConfMinDownshiftTime INTEGER, adslAtucChanConfFastMinTxRate INTEGER, adslAtucChanConfInterleaveMinTxRate INTEGER, adslAtucChanConfFastMaxTxRate INTEGER, adslAtucChanConfInterleaveMaxTxRate INTEGER, adslAtucChanConfMaxInterleaveDelay INTEGER, adslAturConfRateMode INTEGER, adslAturConfRateChanRatio INTEGER, adslAturConfTargetSnrMgn INTEGER, adslAturConfMaxSnrMgn INTEGER, adslAturConfMinSnrMgn INTEGER, adslAturConfDownshiftSnrMgn INTEGER, adslAturConfUpshiftSnrMgn INTEGER, adslAturConfMinUpshiftTime INTEGER, adslAturConfMinDownshiftTime INTEGER, adslAturChanConfFastMinTxRate INTEGER, adslAturChanConfInterleaveMinTxRate INTEGER, adslAturChanConfFastMaxTxRate INTEGER, adslAturChanConfInterleaveMaxTxRate INTEGER, adslAturChanConfMaxInterleaveDelay INTEGER, adslLineConfProfileRowStatus RowStatus } adslLineConfProfileIndex OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line configuration table in order to identify a row of this table" ::= { adslLineConfProfileEntry 1 } adslAtucConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaptation adaptAtStartup (2), -- perform rate adaptation -- only at initialization Expires February 1999 [Page 66] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adaptAtRuntime (3) -- perform rate adaptation at -- any time (i.e., RADSL) } MAX-ACCESS read-create STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information." ::= { adslLineConfProfileEntry 2 } adslAtucConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAtucConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 3 } adslAtucConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 4 } adslAtucConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION Expires February 1999 [Page 67] INTERNET-DRAFT ADSL Line MIB August 7, 1998 "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." ::= { adslLineConfProfileEntry 5 } adslAtucConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 6 } adslAtucConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 7 } adslAtucConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 8 } adslAtucConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" Expires February 1999 [Page 68] INTERNET-DRAFT ADSL Line MIB August 7, 1998 MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 9 } adslAtucConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 10 } adslAtucChanConfFastMinTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 11 } adslAtucChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for receive rates." ::= { adslLineConfProfileEntry 12 } adslAtucChanConfFastMaxTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" Expires February 1999 [Page 69] INTERNET-DRAFT ADSL Line MIB August 7, 1998 MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Fast' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and see ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 13 } adslAtucChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Interleave' channels, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates." ::= { adslLineConfProfileEntry 14 } adslAtucChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 15 } adslAturConfRateMode OBJECT-TYPE SYNTAX INTEGER { fixed (1), -- no rate adaptation adaptAtStartup (2), -- perform rate adaptation -- only at initialization adaptAtRuntime (3) -- perform rate adaptation at -- any time (i.e., RADSL) } MAX-ACCESS read-create Expires February 1999 [Page 70] INTERNET-DRAFT ADSL Line MIB August 7, 1998 STATUS current DESCRIPTION "Defines what form of transmit rate adaptation is configured on this modem. See ADSL Forum TR-005 [3] for more information." ::= { adslLineConfProfileEntry 16 } adslAturConfRateChanRatio OBJECT-TYPE SYNTAX INTEGER(0..100) UNITS "%" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured allocation ratio of excess transmit bandwidth between fast and interleaved channels. Only applies when two channel mode and RADSL are supported. Distribute bandwidth on each channel in excess of the corresponding ChanConfMinTxRate so that: adslAturConfRateChanRatio = [Fast / (Fast + Interleaved)] * 100 In other words this value is the fast channel percentage." ::= { adslLineConfProfileEntry 17 } adslAturConfTargetSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Target Signal/Noise Margin. This is the Noise Margin the modem must achieve with a BER of 10-7 or better to successfully complete initialization." ::= { adslLineConfProfileEntry 18 } adslAturConfMaxSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum acceptable Signal/Noise Margin. If the Noise Margin is above this the modem should attempt to reduce its power output to optimize its operation." Expires February 1999 [Page 71] INTERNET-DRAFT ADSL Line MIB August 7, 1998 ::= { adslLineConfProfileEntry 19 } adslAturConfMinSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum acceptable Signal/Noise Margin. If the noise margin falls below this level, the modem should attempt to increase its power output. If that is not possible the modem will attempt to re-initialize or shut down." ::= { adslLineConfProfileEntry 20 } adslAturConfDownshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate downshift. If the noise margin falls below this level, the modem should attempt to decrease its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 21 } adslAturConfUpshiftSnrMgn OBJECT-TYPE SYNTAX INTEGER(0..310) UNITS "tenth dB" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Signal/Noise Margin for rate upshift. If the noise margin rises above this level, the modem should attempt to increase its transmit rate. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 22 } adslAturConfMinUpshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is above Expires February 1999 [Page 72] INTERNET-DRAFT ADSL Line MIB August 7, 1998 UpshiftSnrMgn before an upshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 23 } adslAturConfMinDownshiftTime OBJECT-TYPE SYNTAX INTEGER(0..16383) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Minimum time that the current margin is below DownshiftSnrMgn before a downshift occurs. In the case that RADSL is not present, the value will be '0'." ::= { adslLineConfProfileEntry 24 } adslAturChanConfFastMinTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Fast' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 25 } adslAturChanConfInterleaveMinTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Minimum Transmit rate for 'Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 26 } adslAturChanConfFastMaxTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Fast' channels, Expires February 1999 [Page 73] INTERNET-DRAFT ADSL Line MIB August 7, 1998 in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 27 } adslAturChanConfInterleaveMaxTxRate OBJECT-TYPE SYNTAX INTEGER UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured Maximum Transmit rate for 'Interleave' channels, in bps. See adslAturConfRateChanRatio for information regarding RADSL mode and see ATUC transmit rate for ATUR receive rates." ::= { adslLineConfProfileEntry 28 } adslAturChanConfMaxInterleaveDelay OBJECT-TYPE SYNTAX INTEGER(0..255) UNITS "milli-seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Configured maximum Interleave Delay for this channel. Interleave delay applies only to the interleave channel and defines the mapping (relative spacing) between subsequent input bytes at the interleaver input and their placement in the bit stream at the interleaver output. Larger numbers provide greater separation between consecutive input bytes in the output bit stream allowing for improved impulse noise immunity at the expense of payload latency." ::= { adslLineConfProfileEntry 29 } adslLineConfProfileRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchObject upon SNMP request." ::= { adslLineConfProfileEntry 30 } Expires February 1999 [Page 74] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslLineAlarmConfProfileIndexNext OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an appropriate value to be used for adslLineAlarmConfProfileIndex when creating entries in the adslLineAlarmConfTable. The value '0' indicates that no unassigned entries are available. To obtain the adslLineAlarmConfProfileIndexNext value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. If the implementator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchObject upon SNMP request." ::= { adslMibObjects 16} adslLineAlarmConfProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the ADSL line configuration. One entry in this table reflects a profile defined by a manager which can be used to configure the modem for a physical line" ::= { adslMibObjects 17} adslLineAlarmConfProfileEntry OBJECT-TYPE SYNTAX AdslLineAlarmConfProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry consists of a list of parameters that represents the configuration of an ADSL modem. A profile is created in one step with all necessary parameter values and adslLineAlarmConfProfileRowStatus set to createAndGo. This RowStatus object is also used to delete destroy profiles." INDEX { adslLineAlarmConfProfileIndex} ::= { adslLineAlarmConfProfileTable 1} AdslLineAlarmConfProfileEntry ::= Expires February 1999 [Page 75] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SEQUENCE { adslLineAlarmConfProfileIndex AdslLineProfileType, adslAtucThresh15MinLofs INTEGER, adslAtucThresh15MinLoss INTEGER, adslAtucThresh15MinLols INTEGER, adslAtucThresh15MinLprs INTEGER, adslAtucThresh15MinESs INTEGER, adslAtucThreshFastRateUp Integer32, adslAtucThreshInterleaveRateUp Integer32, adslAtucThreshFastRateDown Integer32, adslAtucThreshInterleaveRateDown Integer32, adslAtucInitFailureTrapEnable INTEGER, adslAturThresh15MinLofs INTEGER, adslAturThresh15MinLoss INTEGER, adslAturThresh15MinLprs INTEGER, adslAturThresh15MinESs INTEGER, adslAturThreshFastRateUp Integer32, adslAturThreshInterleaveRateUp Integer32, adslAturThreshFastRateDown Integer32, adslAturThreshInterleaveRateDown Integer32, adslLineAlarmConfProfileRowStatus RowStatus } adslLineAlarmConfProfileIndex OBJECT-TYPE SYNTAX AdslLineProfileType MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object is used by the line alarm configuration table in order to identify a row of this table" ::= { adslLineAlarmConfProfileEntry 1} adslAtucThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 2} Expires February 1999 [Page 76] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 3} adslAtucThresh15MinLols OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Link Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLolsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 4} adslAtucThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 5} adslAtucThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) Expires February 1999 [Page 77] INTERNET-DRAFT ADSL Line MIB August 7, 1998 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 6} adslAtucThreshFastRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 7} adslAtucThreshInterleaveRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to 'Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 8} adslAtucThreshFastRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: Expires February 1999 [Page 78] INTERNET-DRAFT ADSL Line MIB August 7, 1998 ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 9 } adslAtucThreshInterleaveRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to 'Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 10 } adslAtucInitFailureTrapEnable OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Enables and disables the InitFailureTrap. This object is defaulted disable(2)." DEFVAL { disable } ::= { adslLineAlarmConfProfileEntry 11 } adslAturThresh15MinLofs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Frame Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLofsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 12 } adslAturThresh15MinLoss OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" Expires February 1999 [Page 79] INTERNET-DRAFT ADSL Line MIB August 7, 1998 MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Signal Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLossThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 13 } adslAturThresh15MinLprs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Loss of Power Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfLprsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 14 } adslAturThresh15MinESs OBJECT-TYPE SYNTAX INTEGER(0..900) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of Errored Seconds encountered by an ADSL interface within any given 15 minutes performance data collection period, which causes the SNMP agent to send an adslAtucPerfESsThreshTrap. Limit of one trap will be sent for any one interval. A value of '0' will disable the trap." ::= { adslLineAlarmConfProfileEntry 15 } adslAturThreshFastRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current Expires February 1999 [Page 80] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 16 } adslAturThreshInterleaveRateUp OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to 'Interleave' channels only. configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate > ChanPrevTxRate plus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 17 } adslAturThreshFastRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to 'Fast' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 18 } adslAturThreshInterleaveRateDown OBJECT-TYPE SYNTAX Integer32 UNITS "bps" MAX-ACCESS read-create STATUS current DESCRIPTION "Applies to 'Interleave' channels only. Configured change in rate causing an adslAtucRateChangeTrap. A trap is produced when: ChanCurrTxRate < ChanPrevTxRate minus the value of this object. Set to '0' to disable." ::= { adslLineAlarmConfProfileEntry 19 } adslLineAlarmConfProfileRowStatus OBJECT-TYPE Expires February 1999 [Page 81] INTERNET-DRAFT ADSL Line MIB August 7, 1998 SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to create a new row or modify or delete an existing row in this table. If the implementator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object is not useful and should return noSuchObject upon SNMP request." ::= { adslLineAlarmConfProfileEntry 20 } -- Line Code Specific Tables -- These are place holders for the Line Code Specific MIBs -- once they become available. adslLCSTable OBJECT IDENTIFIER ::= { adslMibObjects 18 } -- conformance information adslConformance OBJECT IDENTIFIER ::= { adslLineMib 2 } adslGroups OBJECT IDENTIFIER ::= { adslConformance 1 } adslCompliances OBJECT IDENTIFIER ::= { adslConformance 2 } -- compliance statements adslLineMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities which have ADSL interfaces." MODULE -- this module MANDATORY-GROUPS { adslLineGroup, adslPhysicalGroup, adslChannelGroup, adslAtucPhysPerfIntervalGroup, adslAturPhysPerfIntervalGroup, adslLineProfileGroup, adslLineAlarmProfileGroup } GROUP adslLineProfileControlGroup DESCRIPTION Expires February 1999 [Page 82] INTERNET-DRAFT ADSL Line MIB August 7, 1998 "This group is mandatory only when the dynamic profile mode is implemented." GROUP adslAtucPhysPerfRawCounterGroup DESCRIPTION "This group is optional." GROUP adslAturPhysPerfRawCounterGroup DESCRIPTION "This group is optional." GROUP adslAtucChanPerformanceGroup DESCRIPTION "This group is optional." GROUP adslAturChanPerformanceGroup DESCRIPTION "This group is optional." OBJECT adslAtucIntervalNumber SYNTAX INTEGER (1..1) DESCRIPTION "It is allowable to implement only one ATU-C 15-minute performance interval." OBJECT adslAturIntervalNumber SYNTAX INTEGER (1..1) DESCRIPTION "It is allowable to implement only one ATU-R 15-minute performance interval." OBJECT adslAtucIntervalNumber SYNTAX INTEGER (1..1) DESCRIPTION "It is allowable to implement only one ATU-C channel 15-minute performance interval." OBJECT adslAtucIntervalNumber SYNTAX INTEGER (1..1) DESCRIPTION "It is allowable to implement only one ATU-R channel 15-minute performance interval." ::= { adslCompliances 1 } -- units of conformance adslLineGroup OBJECT-GROUP OBJECTS { Expires February 1999 [Page 83] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslLineCoding, adslLineType, adslLineSpecific } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL Line." ::= { adslGroups 1 } adslPhysicalGroup OBJECT-GROUP OBJECTS { adslAtucInvSerialNumber, adslAtucInvVendorID, adslAtucInvVersionNumber, adslAtucCurrSnrMgn, adslAtucCurrAtn, adslAtucCurrStatus, adslAtucCurrOutputPwr, adslAtucCurrAttainableRate, adslAturInvSerialNumber, adslAturInvVendorID, adslAturInvVersionNumber, adslAturCurrSnrMgn, adslAturCurrAtn, adslAturCurrStatus, adslAturCurrOutputPwr, adslAturCurrAttainableRate } STATUS current DESCRIPTION "A collection of objects providing physical configuration information of the ADSL Line." ::= { adslGroups 2 } adslChannelGroup OBJECT-GROUP OBJECTS { adslAtucChanInterleaveDelay, adslAtucChanCurrTxRate, adslAtucChanPrevTxRate, adslAtucChanCrcBlockLength, adslAturChanInterleaveDelay, adslAturChanCurrTxRate, adslAturChanPrevTxRate, adslAturChanCrcBlockLength } STATUS current DESCRIPTION "A collection of objects providing configuration information about an ADSL channel." ::= { adslGroups 3 } adslAtucPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAtucPerfLofs, adslAtucPerfLoss, adslAtucPerfLols, adslAtucPerfLprs, adslAtucPerfESs, adslAtucPerfInits } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-C end)." Expires February 1999 [Page 84] INTERNET-DRAFT ADSL Line MIB August 7, 1998 ::= { adslGroups 4 } adslAtucPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAtucPerfValidIntervals, adslAtucPerfInvalidIntervals, adslAtucPerfCurr15MinTimeElapsed, adslAtucPerfCurr15MinLofs, adslAtucPerfCurr15MinLoss, adslAtucPerfCurr15MinLols, adslAtucPerfCurr15MinLprs, adslAtucPerfCurr15MinESs, adslAtucPerfCurr15MinInits, adslAtucPerfCurr1DayLofs, adslAtucPerfCurr1DayLoss, adslAtucPerfCurr1DayLols, adslAtucPerfCurr1DayLprs, adslAtucPerfCurr1DayESs, adslAtucPerfCurr1DayInits, adslAtucPerfPrev1DayMoniSecs, adslAtucPerfPrev1DayLofs, adslAtucPerfPrev1DayLoss, adslAtucPerfPrev1DayLols, adslAtucPerfPrev1DayLprs, adslAtucPerfPrev1DayESs, adslAtucPerfPrev1DayInits, adslAtucIntervalLofs, adslAtucIntervalLoss, adslAtucIntervalLols, adslAtucIntervalLprs, adslAtucIntervalESs, adslAtucIntervalInits, adslAtucIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-C end) ." ::= { adslGroups 5 } adslAturPhysPerfRawCounterGroup OBJECT-GROUP OBJECTS { adslAturPerfLofs, adslAturPerfLoss, adslAturPerfLprs, adslAturPerfESs } STATUS current DESCRIPTION "A collection of objects providing raw performance counts on an ADSL Line (ATU-R end)." ::= { adslGroups 6 } adslAturPhysPerfIntervalGroup OBJECT-GROUP OBJECTS { adslAturPerfValidIntervals, adslAturPerfInvalidIntervals, adslAturPerfCurr15MinTimeElapsed, adslAturPerfCurr15MinLofs, adslAturPerfCurr15MinLoss, adslAturPerfCurr15MinLprs, adslAturPerfCurr15MinESs, adslAturPerfCurr1DayTimeElapsed, Expires February 1999 [Page 85] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAturPerfCurr1DayLofs, adslAturPerfCurr1DayLoss, adslAturPerfCurr1DayLprs, adslAturPerfCurr1DayESs, adslAturPerfPrev1DayMoniSecs, adslAturPerfPrev1DayLofs, adslAturPerfPrev1DayLoss, adslAturPerfPrev1DayLprs, adslAturPerfPrev1DayESs, adslAturIntervalLofs, adslAturIntervalLoss, adslAturIntervalLprs, adslAturIntervalESs, adslAturIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing current 15-minute, 1-day; and previous 1-day performance counts on ADSL Line (ATU-R end)." ::= { adslGroups 7 } adslAtucChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAtucChanReceivedBlks, adslAtucChanTransmittedBlks, adslAtucChanCorrectedBlks, adslAtucChanUncorrectBlks, adslAtucChanPerfValidIntervals, adslAtucChanPerfInvalidIntervals, adslAtucChanPerfCurr15MinTimeElapsed, adslAtucChanPerfCurr15MinReceivedBlks, adslAtucChanPerfCurr15MinTransmittedBlks, adslAtucChanPerfCurr15MinCorrectedBlks, adslAtucChanPerfCurr15MinUncorrectBlks, adslAtucChanPerfCurr1DayTimeElapsed, adslAtucChanPerfCurr1DayReceivedBlks, adslAtucChanPerfCurr1DayTransmittedBlks, adslAtucChanPerfCurr1DayCorrectedBlks, adslAtucChanPerfCurr1DayUncorrectBlks, adslAtucChanPerfPrev1DayMoniSecs, adslAtucChanPerfPrev1DayReceivedBlks, adslAtucChanPerfPrev1DayTransmittedBlks, adslAtucChanPerfPrev1DayCorrectedBlks, adslAtucChanPerfPrev1DayUncorrectBlks, adslAtucChanIntervalReceivedBlks, adslAtucChanIntervalTransmittedBlks, adslAtucChanIntervalCorrectedBlks, adslAtucChanIntervalUncorrectBlks, adslAtucChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block Expires February 1999 [Page 86] INTERNET-DRAFT ADSL Line MIB August 7, 1998 performance information on an ADSL channel (ATU-C end)." ::= { adslGroups 8 } adslAturChanPerformanceGroup OBJECT-GROUP OBJECTS { adslAturChanReceivedBlks, adslAturChanTransmittedBlks, adslAturChanCorrectedBlks, adslAturChanUncorrectBlks, adslAturChanPerfValidIntervals, adslAturChanPerfInvalidIntervals, adslAturChanPerfCurr15MinTimeElapsed, adslAturChanPerfCurr15MinReceivedBlks, adslAturChanPerfCurr15MinTransmittedBlks, adslAturChanPerfCurr15MinCorrectedBlks, adslAturChanPerfCurr15MinUncorrectBlks, adslAturChanPerfCurr1DayTimeElapsed, adslAturChanPerfCurr1DayReceivedBlks, adslAturChanPerfCurr1DayTransmittedBlks, adslAturChanPerfCurr1DayCorrectedBlks, adslAturChanPerfCurr1DayUncorrectBlks, adslAturChanPerfPrev1DayMoniSecs, adslAturChanPerfPrev1DayReceivedBlks, adslAturChanPerfPrev1DayTransmittedBlks, adslAturChanPerfPrev1DayCorrectedBlks, adslAturChanPerfPrev1DayUncorrectBlks, adslAturChanIntervalReceivedBlks, adslAturChanIntervalTransmittedBlks, adslAturChanIntervalCorrectedBlks, adslAturChanIntervalUncorrectBlks, adslAturChanIntervalValidData } STATUS current DESCRIPTION "A collection of objects providing channel block performance information on an ADSL channel (ATU-C end)." ::= { adslGroups 9 } adslLineProfileGroup OBJECT-GROUP OBJECTS { adslAtucConfRateMode, adslAtucConfRateChanRatio, adslAtucConfTargetSnrMgn, adslAtucConfMaxSnrMgn, adslAtucConfMinSnrMgn, adslAtucConfDownshiftSnrMgn, adslAtucConfUpshiftSnrMgn, adslAtucConfMinUpshiftTime, Expires February 1999 [Page 87] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucConfMinDownshiftTime, adslAtucChanConfFastMinTxRate, adslAtucChanConfInterleaveMinTxRate, adslAtucChanConfFastMaxTxRate, adslAtucChanConfInterleaveMaxTxRate, adslAtucChanConfMaxInterleaveDelay, adslAturConfRateMode, adslAturConfRateChanRatio, adslAturConfTargetSnrMgn, adslAturConfMaxSnrMgn, adslAturConfMinSnrMgn, adslAturConfDownshiftSnrMgn, adslAturConfUpshiftSnrMgn, adslAturConfMinUpshiftTime, adslAturConfMinDownshiftTime, adslAturChanConfFastMinTxRate, adslAturChanConfInterleaveMinTxRate, adslAturChanConfFastMaxTxRate, adslAturChanConfInterleaveMaxTxRate, adslAturChanConfMaxInterleaveDelay } STATUS current DESCRIPTION "A collection of objects providing provisioning information about an ADSL Line." ::= { adslGroups 10 } adslLineAlarmProfileGroup OBJECT-GROUP OBJECTS { adslAtucThresh15MinLofs, adslAtucThresh15MinLoss, adslAtucThresh15MinLols, adslAtucThresh15MinLprs, adslAtucThresh15MinESs, adslAtucThreshFastRateUp, adslAtucThreshInterleaveRateUp, adslAtucThreshFastRateDown, adslAtucThreshInterleaveRateDown, adslAtucInitFailureTrapEnable, adslAturThresh15MinLofs, adslAturThresh15MinLoss, adslAturThresh15MinLprs, adslAturThresh15MinESs, adslAturThreshFastRateUp, adslAturThreshInterleaveRateUp, adslAturThreshFastRateDown, adslAturThreshInterleaveRateDown } STATUS current DESCRIPTION "A collection of objects providing alarm provisioning information about an ADSL Line." ::= { adslGroups 11 } adslLineProfileControlGroup OBJECT-GROUP OBJECTS { Expires February 1999 [Page 88] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslLineConfProfile, adslLineAlarmConfProfile, adslLineConfProfileIndexNext, adslLineConfProfileRowStatus, adslLineAlarmConfProfileIndexNext, adslLineAlarmConfProfileRowStatus } STATUS current DESCRIPTION "A collection of objects providing 'dynamic' profile control for the ADSL system." ::= { adslGroups 12 } -- trap definitions adslTraps OBJECT IDENTIFIER ::= { adslLineMib 3 } adslAtucTraps OBJECT IDENTIFIER ::= { adslTraps 1 } adslAtucPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 1 } adslAtucPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 2 } adslAtucPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 3 } adslAtucPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinESs } STATUS current DESCRIPTION "Errored Second 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 4 } adslAtucRateChangeTrap NOTIFICATION-TYPE OBJECTS {ifIndex, adslAtucChanCurrTxRate, Expires February 1999 [Page 89] INTERNET-DRAFT ADSL Line MIB August 7, 1998 adslAtucChanPrevTxRate } STATUS current DESCRIPTION "The ATUCs transmit rate has changed (RADSL mode only)" ::= { adslAtucTraps 0 5 } adslAtucPerfLolsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucThresh15MinLols } STATUS current DESCRIPTION "Loss of Link 15-minute interval threshold exceeded" ::= { adslAtucTraps 0 6 } adslAtucInitFailureTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAtucCurrStatus } STATUS current DESCRIPTION "ATUC initialization failed. See adslAtucCurrStatus for potential reasons." ::= { adslAtucTraps 0 7 } adslAturTraps OBJECT IDENTIFIER ::= { adslTraps 2 } adslAturPerfLofsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinLofs } STATUS current DESCRIPTION "Loss of Framing 15-minute interval threshold exceeded" ::= { adslAturTraps 0 1 } adslAturPerfLossThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinLoss } STATUS current DESCRIPTION "Loss of Signal 15-minute interval threshold exceeded" ::= { adslAturTraps 0 2 } adslAturPerfLprsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinLprs } STATUS current DESCRIPTION "Loss of Power 15-minute interval threshold exceeded" ::= { adslAturTraps 0 3 } adslAturPerfESsThreshTrap NOTIFICATION-TYPE OBJECTS { ifIndex, adslAturThresh15MinESs } STATUS current Expires February 1999 [Page 90] INTERNET-DRAFT ADSL Line MIB August 7, 1998 DESCRIPTION "Errored Second 15-minute interval threshold exceeded" ::= { adslAturTraps 0 4 } adslAturRateChangeTrap NOTIFICATION-TYPE OBJECTS {ifIndex, adslAturChanCurrTxRate, adslAturChanPrevTxRate } STATUS current DESCRIPTION "The ATURs transmit rate has changed (RADSL mode only)" ::= { adslAturTraps 0 5 } -- no adslAturPerfLolsThreshTrap possible { 6 } -- no adslAturInitFailureTrap possible { 7 } -- these are defined for use as ifTestTypes (see RFC2233[5]) -- additional vendor-specific tests are easily supported -- (just define in vendor MIB) -- adslTestTypes OBJECT-IDENTITY STATUS current DESCRIPTION "Integer values as follows: atucSelfTest (1), aturSelfTest (2) " ::= { adslLineMib 4 } adslTestCodes OBJECT IDENTIFIER ::= { adslLineMib 5 } END 10. Acknowledgments ADSL Forum's TR006[9] editors: Gregory Bathrick (AG Communication Systems) John Burgess (Predictive Systems) The technical leader of the ADSL Forum network management working group was: Chi-Lin Tom (AFC) Contributions were received from the following contributors. Rajesh Abbi (Alcatel) Expires February 1999 [Page 91] INTERNET-DRAFT ADSL Line MIB August 7, 1998 John Burgess (Predictive Systems) Gregory Bathrick (AG Communication Systems) Gail Cone (Amati) Peter Duffy (Atlantech) Kevin Godfrey (Motorola) Bill Hong (Diamond Lane) Bob Jenness (Siemens) Lars Johansson (Ericsson) Tsu Kai Lu (DSC) Gigi Karmous-Edwards (Pulsecom) Ron Knipper (Diamond Lane) Adil Masood (AG Communication Systems) Padmore Peterson (BT) Anna Salguero (SBC) Donald Simon (Motorola) John Stehman (Diamond Lane) Chuck Storry (Newbridge) Chi-Lin Tom (AFC) Frank Van der Putten (Alcatel) Marc Van Vlimmeren (Alcatel) 11. References [1] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure of Management Information for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1902, January 1996. [2] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual Conventions for SNMPv2", RFC 1903, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [3] ADSL Forum TR-005, "Network Management Element Management", March 1998. [4] McCloghrie, K., and M. Rose, Editors, "Management Information Base for Network Management of TCP/IP-based internets: MIB-II", STD 17, RFC 1213, Hughes LAN Systems, Performance Systems International, March 1991. [5] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB using SMIv2", RFC 2233, Cisco Systems, FTP Software, November 1997. [6] RFC 1907, "Management Information Base for Version 2 of the Simple Network Management Protocol (SNMPv2)", January 1996. Expires February 1999 [Page 92] INTERNET-DRAFT ADSL Line MIB August 7, 1998 [7] Case, J., Fedor, M., Schoffstall, M., and J. Davin. " A Simple Network Management Protocol (SNMP)", STD 15, RFC 1157, SNMP Research, Performance Systems International, MIT Lab for Computer Science, May 1990. [8] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol Operations for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1905, January 1996. [9] ADSL Forum TR-006, "SNMP-based ADSL Line MIB", March 1998. [10] American National Standards Institute, ANSI T1.413-1995, August 1995. [11] ADSL Forum WT-022, "DMT Line Code Specific MIB", June 1998. [12] ADSL Forum WT-023, "CAP Line Code Specific MIB", June 1998. [13] Harrington, D., Presuhn, R., and B. Wijnen, "An Architecture for Describing SNMP Management Frameworks", RFC 2271, Cabletron Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, January 1998 [14] Rose, M., and K. McCloghrie, "Structure and Identification of Management Information for TCP/IP-based Internets", RFC 1155, Performance Systems International, Hughes LAN Systems, May 1990 [15] Rose, M., and K. McCloghrie, "Concise MIB Definitions", RFC 1212, Performance Systems International, Hughes LAN Systems, March 1991 [16] M. Rose, "A Convention for Defining Traps for use with the SNMP", RFC 1215, Performance Systems International, March 1991 [17] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Conformance Statements for Version 2 of the Simple Network Management Protocol (SNMPv2)", RFC 1904, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [18] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Introduction to Community-based SNMPv2", RFC 1901, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [19] SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Transport Mappings for Version 2 of the Simple Expires February 1999 [Page 93] INTERNET-DRAFT ADSL Line MIB August 7, 1998 Network Management Protocol (SNMPv2)", RFC 1906, SNMP Research, Inc., Cisco Systems, Inc., Dover Beach Consulting, Inc., International Network Services, January 1996. [20] Case, J., Harrington D., Presuhn R., and B. Wijnen, "Message Processing and Dispatching for the Simple Network Management Protocol (SNMP)", RFC 2272, SNMP Research, Inc., Cabletron Systems, Inc., BMC Software, Inc., IBM T. J. Watson Research, January 1998. [21] Blumenthal, U., and B. Wijnen, "User-based Security Model (USM) for version 3 of the Simple Network Management Protocol (SNMPv3)", RFC 2274, IBM T. J. Watson Research, January 1998. [22] Levi, D., Meyer, P., and B. Stewart, MPv3 Applications", RFC 2273, SNMP Research, Inc., Secure Computing Corporation, Cisco Systems, January 1998. [23] Wijnen, B., Presuhn, R., and K. McCloghrie, "View-based Access Control Model (VACM) for the Simple Network Management Protocol (SNMP)", RFC 2275, IBM T. J. Watson Research, BMC Software, Inc., Cisco Systems, Inc., January 1998. [24] Ahmed, M., and K. Tesink, Editors, "Definitions of Managed Objects for ATM Management Version 8.0 using SMIv2", RFC 1695, Bell Communications Research, August 1994. [25] McCloghrie, K. and A. Bierman, "Entity MIB", RFC 2037, October 1996. [26] Yergeau, F., "UTF-8, a transformation format of Unicode and ISO 10646", RFC 2044, October 1996. 12. Security Considerations 1) Blocking unauthorized access to the ADSL MIB via the element management system is outside the scope of this document. It should be noted that access to the MIB permits the unauthorized entity to modify the profiles (sect 7.4) such that both subscriber service and network operations can be interfered with. Subscriber service can be altered by modifying any of a number of service characteristics such as rate partitioning and maximum transmission rates. Network operations can be impacted by modification of trap thresholds such as SNR margins. Expires February 1999 [Page 94] INTERNET-DRAFT ADSL Line MIB August 7, 1998 2) Security issues of unauthorized access, unauthorized disclosure, and tampering posed by direct network level connectivity to the ADSL Access Node can be addressed by the use of SNMPv3. 3) ADSL layer connectivity from the ATU-R will permit the subscriber to manipulate both the ADSL link directly and the AOC/EOC channels for their own loop. For example, unchecked or unfiltered fluctuations initiated by the subscriber could generate sufficient traps to potentially overwhelm either the management interface to the network or the element manager. Other attacks affecting the ATU-R portions of the MIB may also be possible. 13. Authors' Addresses Gregory Bathrick AG Communication Systems 2500 W Utopia Rd. Phoenix, AZ 85027 USA Tel: +1 602-582-7679 Fax: +1 602-582-7697 E-MAIL: bathricg@agcs.com Table of Contents 1. Status of this Memo ................................... 1 2. Abstract .............................................. 1 3. The SNMP Network Management Framework ................. 2 4. Object Definitions ..................................... 3 5. Introduction ........................................... 3 6. Relationship of the ADSL LINE MIB with standard MIBs ... 3 7. Conventions used in the MIB ............................ 9 8. Conformance and Compliance ............................. 16 9. Definitions ............................................ 16 10. Acknowledgments ........................................ 91 11. References ............................................. 92 Expires February 1999 [Page 95] INTERNET-DRAFT ADSL Line MIB August 7, 1998 12. Security Considerations ................................ 94 13. Authors' Addresses ..................................... 95 Expires February 1999 [Page 96]