Network Working Group Don Fedyk, David Allan, Nortel Internet Draft Greg Sunderwood, Bell Canada Category: Standards Track Himanshu Shah, Ciena June 2006 GMPLS control of Ethernet draft-fedyk-gmpls-ethernet-pbt-00.txt (was: GMPLS Control of Ethernet IVL Switches) Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire in December 2006. Copyright Notice Copyright (C) The Internet Society (2006). Abstract This memo describes how GMPLS signaling may be applied to Provider Backbone Transport (PBT) or configured Ethernet switches in order to establish Ethernet P2P and P2MP MAC switched paths and P2MP VID based trees. This utilizes a domain wide label for maintaining unique Ethernet capabilities combined with GMPLS control. Fedyk et.al Expires December 2006 Page 1 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt Table of Contents 1. Introduction...................................................4 2. Terminology....................................................4 3. Aspects of configuring Ethernet Forwarding.....................4 4. Overview of configuration of VID/MAC tuples....................7 5. Overview of configuration of VID port membership..............10 6. OAM Aspects...................................................10 7. QOS Aspects...................................................11 8. Resiliency Aspects............................................11 8.1 E2E Path protection.........................................11 8.2 Local Repair................................................11 9. Deployment Scenarios..........................................12 10. Path creation and maintenance...............................12 10.1.1 Using a GMPLS Control Plane for Ethernet.................12 10.1.2 Control Plane Network....................................13 10.1.3 Signaling................................................13 10.1.4 Ethernet Label...........................................15 10.1.5 Ethernet Service.........................................16 10.1.6 GMPLS Routing............................................16 10.1.7 Path Computation.........................................17 10.1.8 Combinations of GMPLS Features...........................17 10.2 Addresses, Interfaces, and Labels..........................18 11. Specific Procedures.........................................19 11.1 PT to PT connections.......................................19 11.2 P2P connections with shared forwarding.....................19 11.2.1 Dynamic P2P symmetry with shared forwarding..............20 11.2.2 Planned P2P symmetry.....................................20 11.2.3 Path Maintenance.........................................20 11.3 P2MP VID/MAC Connections...................................21 11.3.1 Setup procedures.........................................21 11.3.2 Maintenance Procedures...................................21 11.4 P2MP VID Trees.............................................21 11.4.1 Setup Procedures.........................................21 11.4.2 Maintenance procedures...................................22 11.5 OAM MEP ID and MA ID synchronization.......................22 11.6 Protection Paths...........................................23 12. Error conditions............................................23 12.1 Invalid VID value for configured VID/MAC range.............23 12.2 Invalid VID value for configured VID range.................23 12.3 Invalid MAC Address........................................23 12.4 Invalid ERO for Upstream Label Object......................23 12.5 Invalid ERO for Suggested Label Object.....................23 12.6 Switch is not IVL capable..................................23 12.7 Switch is not SVL capable..................................23 12.8 Switch is not Asymmetric VID capable.......................23 12.9 Invalid VID in upstream label object.......................24 13. Security Considerations.....................................24 14. IANA Considerations.........................................24 15. References..................................................24 Fedyk et al. Expires December 2006 Page 2 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt 15.1 Normative References.......................................24 15.2 Informative References.....................................24 16. Author's Address............................................25 17. Intellectual Property Statement.............................26 18. Disclaimer of Validity......................................26 19. Copyright Statement.........................................27 20. Acknowledgments.............................................27 Fedyk et al. Expires December 2006 Page 3 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt 1. Introduction Ethernet switches are increasing in capability. As a consequence the role of Ethernet is rapidly expanding in networks that were the domain of other technologies such as SONET/SDH TDM and ATM. The question of how Ethernet will evolve and what capabilities it can offer in these areas is still under development. This document explores some unique capabilities that Ethernet has and blends them with some of the values of control planes developed in the IETF. Some of the techniques for repurposing Ethernet switching outlined in this document have been introduced elsewhere as a complement to IEEE 802.1ah Provider Backbone Bridging under the title "Provider Backbone Transport"(PBT). PBT is simply the data plane of Ethernet (802.1Q, 802.1ah) without a Spanning tree control plane. This document applies to PBT and is applicable to 802.1 when used for a suitable Pseudo wire service as described in this document. 2. Terminology In addition to well understood GMPLS terms, this memo uses terminology from IEEE 802.1 and introduces a few new terms: B-MAC Backbone MAC B-VID Backbone VLAN ID B-VLAN Backbone VLAN COS Class of Service C-MAC Customer MAC C-VID Customer VLAN ID C-VLAN Customer VLAN DMAC Destination MAC Address IVL Independent VLAN Learning MAC Media Access Control MP2MP Multipoint to multipoint PBB Provider Backbone Bridge PBT Provider Backbone Transport P2P Point to Point P2MP Point to Multipoint QOS Quality of Service SMAC Source MAC Address S-VID Service VLAN ID VID VLAN ID VLAN Virtual LAN 3. Aspects of configuring Ethernet Forwarding Ethernet as specified today is a complete system consisting of a data plane and a number of control plane functions. Spanning tree, data plane flooding and MAC learning combine to populate forwarding Fedyk et al. Expires December 2006 Page 4 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt tables and produce resilient any-to-any behavior in a bridged network. Ethernet consists of a very simple and reliable data plane that has been optimized and mass produced. By simply disabling some Ethernet control plane functionality, it is possible to employ alternative control planes and obtain different forwarding behaviors. Customer Provider Provider Bridge/ Bridge Backbone Bridge C-MAC/C-VID------------------802.1Q -------------------C-MAC-CVID S-VID-----------802.1ad------------S-VID B-MAC---802.1ah---B-MAC B-VID---802.1ah---B-VID Figure 1 802.1 MAC/VLAN Hierarchy Recent works in IETF Pseudo Wire Emulation [PWE] and IEEE 802 are defining a separation of Ethernet functions permitting an increasing degree of provider control. The result is that the Ethernet service to the customer appears the same, yet the provider components and behaviors have become decoupled from the customer presentation and the provider has gained control of all MAC endpoints. One example of this is the 802.1ah work in hierarchical bridging whereby customer Ethernet frames are fully encapsulated into a provider Ethernet frame, isolating the customer MAC space from the provider MAC space. Another example would be the direct transport of pseudo wires PWs ["Dry Martini" or PW over layer 2] where the Ethernet network fulfills the role of the PSN in the PWE architecture. In both cases the behavior of the provider's network is as per 802.1Q. The Ethernet data plane provides protocol multiplexing via the ether type field which allows encapsulation of different protocols supporting various applications. More recently, the Carrier Ethernet effort has created provider and customer separation that enables another level of multiplexing. This in effect creates provider MAC endpoints in the Ethernet sub-network controlled by the provider. In this document we concentrate on the provider solutions and therefore subsequent references to VLAN, VID and MAC refer to those under provider control, be it in the backbone layer of 802.1ah or the PSN layer of "Dry Martini". Also in the case where the Customer service is Ethernet, the Customer Ethernet service is the same native Ethernet service with functions such as bridging, learning and spanning trees all functioning over the provider infrastructure. With the provider in exclusive control of their Ethernet sub-network and all customer specific state pushed to the edges of that sub- network, the ability of the provider to exploit latent Ethernet behavior is facilitated. One key capability sought is to overcome Fedyk et al. Expires December 2006 Page 5 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt limitations, such as single spanning tree path for all traffic within a VLAN, imposed by bridging (see [MYERS] for a discussion). Bridging offers a simple solution for any-to-any connectivity within a VLAN partition via the Spanning tree. Spanning tree provides unnecessary capability for point to point services and since the Spanning tree must interconnect all MACs with the same VLAN IDs it consumes a scarce resource (VIDS). It is easier to modify Ethernet to scale engineered P2P services and this is the approach we take with PBT and PW over Ethernet. (The number of usable VLANs IDs in conventional Ethernet bridging is constrained to 4094, therefore the use of VLAN only configuration for all forwarding could be limited for some applications where large number of point to point connections are required.) This is because in Ethernet, each Spanning trees is associated with one or more VLAN IDs. Also Port membership in a VLAN is configured which controls the connectivity of all MAC interfaces participating in the VLAN. The roots for PBT capability exist in the Ethernet management plane. The management of Ethernet switches provides for static configuration of Ethernet forwarding. The Ethernet Control plane allows for forwarding entries that are statically provisioned or configured. In this document we are expanding the meaning of "configured" from an Ethernet Control plane sense to mean either provisioned or controlled by GMPLS. The connectivity aspects of Ethernet forwarding is based upon VLANs and MAC addresses. In other words the VLAN + DMAC are an Ethernet Label that can be looked up at each switch to determine the egress link (or links in the case of link aggregation). In this document, we discuss, point to point (P2P) and point to multipoint (P2MP) connections via static configuration of VLAN/MAC tuples. (MAC-only configuration is considered a degenerate case corresponding to VLAN zero). This is a finer granularity than traditional VLAN networks since each P2P connection is independent. By provisioning MAC addresses independent of Spanning tree in a domain, both the VLAN and the VLAN/MAC configured forwarding can be exploited. This greatly extends the scalability of what can be achieved in a pure Ethernet bridged sub network. For compatibility and flexibility with existing Ethernet hardware, we preserve the global/domain wide uniqueness and semantics of MAC addresses as interface names or multicast group addresses. We then redefine the semantics associated with administration and uses of VLAN values for the case of explicit forwarding such as you get with IVL. The result is a new architecture where configured VID + DMAC provide a forwarding table that is consistent with existing Ethernet switching. At the same time it provides domain wide labels that can be controlled by a common GMPLS control plane. This makes GMPLS Fedyk et al. Expires December 2006 Page 6 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt control and resource management procedures ideal to create paths. The outcome is that the GMPLS control plane can be utilized to set up the following atomic modes of connectivity: 1) P2P connectivity and MP2P multiplexed connectivity based on configuration of unicast MAC addresses in conjunction with a VID from a set of pre-configured VIDs. 2) P2MP connectivity based on configuration of multicast MAC address in conjunction with a VID from a set of pre- configured VIDs. This corresponds to (Source, Group) or (S,G) multicast. 3) P2MP connectivity based on configuration of VID port membership. This corresponds to (S,*) or (*,*) multicast (where * represents the extent of the VLAN Tree). 4) MP2MP connectivity based on configuration of VID port membership (P2MP trees in which leaves are permitted to communicate). Although, we caution that this approach poses resilience issues (discussed in section 5) and hence is not recommended. Items 1 and 2 above are restricted to "Independent VLAN Learning" capable Ethernet switches [802.1Q]. The modes above are not completely distinct. Some modes involve combinations of P2P connections in one direction and MP connectivity in the other direction. Also, more than one mode may be combined in a single GMPLS transaction. One example is the incremental addition of a leaf to a P2MP tree with a corresponding MP2P return path (analogous to a root initiated join). In order to realize the above connectivity modes, a partition of the VLAN IDs from traditional Ethernet needs to be established. The partition allows for a pool of Ethernet labels for manual configuration and/or for GMPLS control plane usage. The VID partition actually consists of a "configured VID/MAC range" and "configured VID range" since in some instances the label is a VID/DMAC and sometimes the label is a VID/Mulitcast DMAC. 4. Overview of configuration of VID/MAC tuples Existing Ethernet Switches may perform Independent VLAN Learning (IVL) based forwarding on the basis of a VID/DMAC tuple as described in 802.1Q. This means the forwarding hardware performs a full 60 bit lookup (VID (12) + DMAC(48)), only requiring uniqueness of the full 60 bits for forwarding to resolve correctly. We can call this an Ethernet domain wide label. The label becomes unique MAC address in the domain per VLAN. We have complete route freedom for each label (60 bit VLAN/MAC tuple) and the ability to define multiple connectivity instances or paths per MAC for each of the VIDs in the "configured VID/MAC range". Fedyk et al. Expires December 2006 Page 7 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt We have preserved the semantics of MAC addresses, and simply broaden the potential interpretations of VLAN ID from spanning tree identifier to topology instance identifier. Therefore, we can concurrently operate both standard bridging and configured unicast/multicast operation side by side. We partition the VID space and allocate a range of VIDs (say 'n' VIDs) as only significant when combined with a configured MAC address (the aforementioned "configured VID/MAC range" of VIDs). We can then consider a VID in that range as an individual connectivity instance identifier for a configured P2P path terminating at the associated destination MAC address. Or in the case of P2MP, a P2MP multicast tree corresponding to the destination multicast group address. Note that this is destination based forwarding consistent with how Ethernet works today. The only thing changed is the mechanism of populating the forwarding tables. Ethernet MAC addresses are typically globally unique since the 48 bits consists of 24 bit Organizational Unique Identifier and a 24 bit serial number. There is also a bit set aside for Multicast and for local addresses out OUI field. We define domain wide as within a single organization, or more strictly within a single network within an organization. For provider MAC addresses that will only be used in a domain wide sense we can define MAC addresses out of a either the local space or the global space since they both have the domain wide unique property. When used in the context of GMPLS is useful to think of a domain wide pool of labels where switches are assigned a set of MAC addresses. These labels are assigned traffic that terminates on the respective switches. It is also worth noting that unique identification of source in the form of the SMAC is carried e2e in the MAC header. So although we have a 60 bit domain wide unique label, it may be shared by multiple sources and the full connection identifier for an individual P2P instance is 108 bits (SMAC, VID and DMAC). The SMAC is not referenced in forwarding operations but it would allow additional context for tracing or other operations at the end of the path. GMPLS signaling procedures can be designed to create the bi- directional path delegating label allocation of the combined MAC/VID Label to the destination/source associated with the MACs for each direction of unicast forwarding. Creating P2P path is a well understood control plane requirement. For multicast group addresses, the VID/MAC concatenated label can be distributed by the source but label assignment (as it encodes global multicast group information) requires coordination within the GMPLS controlled domain. As mentioned earlier, this technique results in a single unique and invariant identifier, in our case a VID/MAC label associated with the path termination or the multicast group. There can be up to 4094 labels to any one MAC address. This is a large number for P2P Fedyk et al. Expires December 2006 Page 8 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt applications and extremely large when shared or multiplexed forwarding is leveraged. In practice, most network scaling requirements may be met via allocation of only a small portion of the VID space, to the configured VID/MAC range. The result is minimal impact on the number of remaining bridging VLANs that can be concurrently supported. In order to use this unique 60 bit label, we disable the normal mechanisms by which Ethernet populates the forwarding table for the allocated range of VIDs. We use GMPLS signaling to create paths and assign labels to the forwarding table. When a path is setup, for a specific label across a contiguous sequence of Ethernet switches, a unidirectional connection is the functional building block for an Ethernet Label Switched path (Eth-LSP). In P2P mode a bi-directional path is composed of two unidirectional paths that are created with a single RSVP-TE session. The technique does not require the VID to be common in both directions. However, keeping in line with regular Ethernet these paths are symmetrical such that a single bi-directional connection is composed of two unidirectional paths that have common routing (i.e. traverse the same switches and links) in the network and hence share the same fate. One departure from current GMPLS signaling is there needs to be a provision for asymmetrical bandwidth reservations. In P2MP mode a bi-directional path is composed of a unidirectional tree and a number of P2P paths from the leaves of the tree to the root. Similarly these paths may have bandwidth and must have common routing as in the P2P case. There are a few modifications required to standard Ethernet to make this approach robust: 1. In Standard Ethernet, discontinuities in forwarding table configuration in the path of a connection will normally result in packets being flooded as "unknown". For configured operation (e.g. PBT), unknown addresses are indicative of a fault or configuration error and the flooding of these is undesirable in meshed topologies. Therefore flooding of "unknown" unicast/multicast MAC addresses must be disabled for the "configured VID/MAC range". 2. MAC learning is not required, and although it will not interfere with management/control population of the forwarding tables, since static entries are not overridden, it appears prudent to explicitly disable MAC learning for the configured VID/MAC and VID range. 3. Spanning tree is disabled for the allocated VID/MAC and VID range and port blocking must be disabled to achieve complete configured route freedom. As noted earlier, it is a control plane requirement to ensure configured paths are loop free. Fedyk et al. Expires December 2006 Page 9 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt All three modifications described above are within the scope of acceptable configuration options defined in IEEE802.1Q specification. 5. Overview of configuration of VID port membership Procedures almost identical to that for configuration of P2P VID/MAC tuples can also be used for the incremental configuration of P2MP VID trees. For the replication of forwarding in this case the label is common for the multipoint destinations. The MAC field is set to multicast address and is common to the multicast community. The VID is a distinguisher common to the multicast community. The signaling procedures are as per that for [MPLS-P2MP]. Since VID translation is relatively new and is not a ubiquitously deployed capability, we consider a VID to be a domain global value. Therefore, the VID value to be used by the originating switch may be assigned by management and nominally is required to be invariant across the network. The ability to indicate permissibility of translation will be addressed in a future version of the document. A procedure known as "asymmetrical VID" may be employed to constrain connectivity (root to leaves, and leaves to root only) when switches also support shared VLAN learning (or SVL). This would be consistent with the root as a point of failure. 6. OAM Aspects Robustness is enhanced with the addition of data plane OAM to provide both fault and performance management. For the configured VID/MAC unicast mode of behavior, the hardware performs unicast packet forwarding of known MAC addresses exactly as Ethernet currently operates The OAM currently defined,[802.1ag, Y.1731] can also be reused without modification of the protocols. An additional benefit of domain wide path identifiers for data plane forwarding, is the tight coupling of the 60 bit unique connection ID (VID + DMAC ) and the associated OAM packets. It is a simple matter to determine a broken path or misdirected packet since the unique connection ID cannot be altered on the Eth-LSP. This is in fact one of the most powerful and unique aspects of the domain wide label for any type of rapid diagnosis of the data plane faults. It is also independent of the control plane so it works equally well for provisioned or GMPLS controlled paths. Bi-directional transactions (e.g. ETH-LB) and reverse direction transactions (e.g. ETH-AIS) will have a different VID for each direction. Currently Y.1731 & 802.1ag makes no representations with respect to this. Fedyk et al. Expires December 2006 Page 10 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt For configured multicast VID/MAC mode, the current versions of 802.1ag, Y.1731] make no representation as to how PDUs which are not using unicast addresses or which use OAM reserved multicast addresses are handled. Therefore this specification makes no representation as to whether such trees can be instrumented. For configured VID mode of operation, the OAM functions as defined in the current versions of 802.1ag, Y.1731 can be used with no restriction. 7. QOS Aspects Ethernet VLAN tags include priority tagging in the form of the 802.1p priority bits. When combined with configuration of the paths via management or control plane, priority tagging produces the Ethernet equivalent of an MPLS TE E-LSPs [MPLS-DS]. Priority tagged Ethernet PDUs self-identify the required queuing discipline independent of the configured connectivity. It should be noted that the consequence of this is that there is a common COS model across the different modes of configured operation specified in this document. The actual QOS objects required for signaling will be in a future version of this memo. 8. Resiliency Aspects 8.1 E2E Path protection 1:1 and 1+1 path protection strategies are supported. Such schemes offer: 1) Engineered disjoint protection paths that can protect both directions of traffic. 2) Fast switchover due to tunable OAM mechanisms. 3) Revertive path capability when primary paths are restored. 4) Option for redialing paths under failure. Specific procedures for establishment of protection paths and associating paths into "protection groups" are described later in this document. Note that E2E path protection is able to respond to failures with a number of configurable intervals. The loss of CCM OAM cells or ETH- AIS cells in the data plane can trigger paths to switch. In the case of CCM OAM cells the detection time is a typically 3.5 the CCM interval + the propagation delay from the fault. 8.2 Local Repair At this time local repair such as IPFRR with detours or bypass tunnels is not considered as there are obstacles both with Ethernet and the labeling techniques described in this document. Alternate Fedyk et al. Expires December 2006 Page 11 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt path techniques such as warm standby and hot standby work well since data path OAM is able to provide configurable response time as mentioned earlier. 9. Deployment Scenarios This technique of GMPLS controlled Ethernet switching is applicable to all deployment scenarios considered by the design team [CCAMP- ETHERNET]. 10. Path creation and maintenance One simple mode of path creation described earlier is configuration. Switch by switch a path can be created by simple configuration and assignment of labels or by a set of commands originating from a management system. When configuring a PBT path the label VID + DMAC is assigned hop by hop invariant and it is intuitive to associate the label with the path. While this property is a desirable attribute, to be consistent with GMPLS terminology, and more accurate, paths are created first as an ERO and labels are assigned from the available label pool. In this case we use a domain wide label. One improvement to switch by switch configuration is to move to single ended provisioning and signaling. Since signaling of explicit paths is the domain of CCAMP and GMPLS we discuss the applicability of GMPLS to this problem. Several attributes may be associated with an Eth-LSP, including: - bandwidth requirements of the path. This can be used, for example, to request a fixed bandwidth path, where the committed information rate and peak information rate of the path are equivalent. - priority level; - preemption characteristics; - protection/resiliency requirements; - routing policy, such as an explicit route; - policing requirements In addition to the above policies based on either under-subscription or over-subscription can be supported. 10.1.1 Using a GMPLS Control Plane for Ethernet GMPLS [GMPLS-ARCH] has been adapted to the control of optical switches for the purpose of managing optical paths. GMPLS signaling is well suited to setup paths with labels but it does require a minimal IP control plane and IP connectivity, so it is suited to certain scenarios where a large number of paths or dynamic path management is required. Fedyk et al. Expires December 2006 Page 12 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt In many Ethernet deployment situations the addition of a complete GMPLS control plane may be excessive for the switches or the application. For discussion purposes we decompose the problem into Signaling, Routing, Link discovery and Path management. While we discuss the options it will become apparent that using all functions of GMPLS is less of an operational overhead than any other combination. Also, using only some components of GMPLS can lead to more provisioned parameters than a purely static system (see "Combinations of GMPLS Features"). Link discovery is one of the foundations of GMPLS. It is also a capability that has been specified for Ethernet in IEEE 802.1AB. All link discovery is optional but the benefits of running link discovery in large systems are significant. It reduces configuration and the possibility of errors in configuration. A recommendation is that 802.1AB could be run with an extension to feed information into an LMP [LMP] information model. See Figure 3. +---------+ +---------+ | | | | | LMP | ----------| LMP | | +-------+ IP (opt) +-------+ | | |802.1AB| ----------|802.1AB| | +-+-------+ Ethernet +-------+-+ Figure 3 Link Discovery Hierarchy 10.1.2 Control Plane Network In order to have a GMPLS control plane, an IP control plane consisting of an IGP with TE extension needs to be established. This IGP sees each hop as a terminated IP adjacency and should not be interpreted as a distinct routed subnet for the purpose of carrying IP bearer traffic. This IP control plane can be provided as a separate independent network (out of band) or integrated with the Ethernet switches. If the IP control plane is a separate network, it may be provided as a Layer 2 connected VLAN where the Ethernet switches are connected via a bridged network or HUB. It may also be provided by an external network that provides IP connectivity but the GMPLS/Ethernet switches are not immediately adjacent to each other. If the IP control plane is integrated with the switches it may be provided by a bridged VLAN that uses the Data bearing channels of the network between adjacent nodes. This ties the fate of the controlled paths and the IP control plane links, but it is likely the same Ethernet hardware is already using shared network resources with other networks. 10.1.3 Signaling Fedyk et al. Expires December 2006 Page 13 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt GMPLS signaling is well suited to the set up of PBT on Ethernet switches. GMPLS signaling uses either numbered or unnumbered links where the link is either explicitly IP addressed or associated with a switch loopback address. If LMP [LMP] is used, the creation of these unnumbered interfaces can be automated. If LMP is not used there is an additional provisioning requirement to add GMPLS link identifiers. For large-scale implementations LMP would be beneficial. As mentioned earlier the primary benefit of signaling is the control of a path from an endpoint. GMPLS can be used to create bi-directional or unidirectional paths, bi-directional paths being the preferred mode of operation for numerous reasons (OAM consistency etc.). In this document we only consider bidirectional paths both for P2P and P2MP services. Signaling enables the ability to dynamically establish a path and to adjust the path in a coordinated fashion after the path has been established. Signaling also allows multi-vendor interoperability since the signaling is based on GMPLS signaling protocols. This allows the network to adapt to changing conditions or failures with a single mechanism. Signaling can be used for pure static paths as well. To use GMPLS RSVP-TE for signaling, a new label is defined that contains the VID/DMAC tuple, which is 60 bits. On the initiating and terminating nodes, a function administers the VIDs associated with the MAC SMAC and DMAC respectively. To initiate a bi-directional VID/MAC P2P or P2MP path, the initiator of the PATH message uses procedures outlined in [GMPLS-SIGNALING] possibly augmented with [MPLS-P2MP], it: 1) Sets the LSP encoding type to Ethernet. 2) Sets the LSP switching type to MAC [IANA to define]. 3) Sets the GPID to Unknown (1) or Ethernet Multiplexed [IANA to define]. 4) Sets the UPSTREAM_LABEL to the VID/SMAC tuple where the VID is administered from the configured VID/MAC range. Downstream switches must use the suggested label or return a path Error condition indicating why the label could not be used. At intermediate switches the UPSTREAM_LABEL object and value is passed unmodified. The VID/SMAC tuple is installed in the forwarding table at each hop for the upstream direction. Note that shared forwarding happens opportunistically when conditions are met as a local decision. To achieve shared forwarding, a Path computation engine must ensure the ERO is consistent with an existing path for the shared segments. The only other criterion is the paths cannot separate and cross. If no existing path has this behavior the path will be created unshared. Fedyk et al. Expires December 2006 Page 14 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt In other words shared forward happens when paths share segments from the source and when the Upstream label is chosen to be the same as the existing path. Similarly for the downstream path shared forwarding happens when, an existing path that shares segments with the new paths ERO, viewed from the destination switch and when the downstream label is chosen to be the same and the existing path. In this manner shared forwarding is a function that is controlled primarily by path calculation and in combination with the local label allocation at the end points of the path. At the destination, a VID is allocated in the local MAC range for the DMAC and the VID/DMAC tuple is passed in the GENERALIZED_LABEL in the RESV message. As with the UPSTREAM_LABEL, intermediate switches use the GENERALIZED_LABEL object and pass it on unchanged, upstream. The VID/DMAC tuple is installed in the forwarding table at each hop. This creates a bi-directional path as the PATH and RESV messages follow the same path. To initiate a P2MP VID path the initiator of the PATH message uses procedures outlined in [GMPLS-SIGNALING] and [MPLS-P2MP]. A P2MP tree consists of a VID tree in the forward direction (from root to leaves) and a set of P2P paths running on identical paths from Tree to root in the reverse direction. VID labels with common MAC addresses are allocated in the forward direction and a single VID/MAC label in the reverse direction: 1) Sets the LSP encoding type to Ethernet. 2) Sets the LSP switching type to L2SC. 3) Sets the GPID to unknown. 4) Set the technology specific information in the TSPEC to indicate domain-wide label. 5) Sets the UPSTREAM LABEL specified as a single VID/MAC from the configured VID range. 6) VID translation may optionally be permitted on a local basis between two switches by a downstream switch replying with a VID/MAC other than the SUGGESTED LABEL. The upstream switch then sets a VID translation on the port associated with the label to allow VID translation. This flexibility allows the tree to be constructed with out having to worry about colliding with another tree using the same VID. 10.1.4 Ethernet Label The Ethernet label is a new generalized label with a suggested format of: Fedyk et al. Expires December 2006 Page 15 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |0 0 0 0| VLAN ID | MAC (highest 2 bytes) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | MAC Address | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Note that there is no syntax in signaling to force the label in the UPSTREAM_LABEL and GENERALIZED_LABEL objects to be passed unchanged (which needs to be addressed). The semantics of the new label type for a non-zero MAC address is that that the label is passed unchanged. This label is a domain wide label. This has similarity to the way in which a wavelength label is handled at an intermediate switch that cannot perform wavelength conversion, and is described in [GMPLS-RSVP]. These domain wide labels are allocated to switches that control the assignment of labels. This label space does not have to be globally unique because the labels are only valid within a single provider. When using configuration, a tool would have to perform a consistency check to make sure that label terminations were unique. When using GMPLS signaling it is assumed a unique pool of labels would be assigned to each switch. The DMAC addresses are domain wide unique and so is the combination of VID/DMAC. Should an error occur and a duplicate label be assigned to one or more switches GMPLS signaling procedures would allow the first assignment of the label and prevent duplicate label from colliding. If a collision occurs an alarm would be generated. In fact some of these procedures have been defined in GMPLS control of photonic networks where a lambda may exist as a form of domain wide label. 10.1.5 Ethernet Service Ethernet Switched Paths that are setup either by configuration or signaling can be used to provide an Ethernet service to customers of the Ethernet network. The Metro Ethernet Forum has defined some services in MEF.6 (e.g., Ethernet Private Line), and these are also aligned with ITU-T G.8011-x Recommendations. Of particular interest are the bandwidth profile parameters in MEF.10 and whose associated bandwidth profile algorithm are based on [DS-COLOR][MPLS-DS]. Consideration should be given to supporting these in any signaling extensions for Ethernet LSPs. This will be addressed in a future version of this specification. 10.1.6 GMPLS Routing Fedyk et al. Expires December 2006 Page 16 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt GMPLS routing [GMPLS-ROUTING] is IP routing with the TLV extensions for the purpose of carrying around GMPLS TE information. The TE information is populated with TE resources from LMP or from configuration if LMP is not available. GMPLS Routing is an optional piece but it is highly valuable in maintaining topology for path management and dynamic path computation. 10.1.7 Path Computation There has been a lot of recent activity in the area of path computation [PATH-COMP]. Originally MPLS path computation was performed locally in a TE database on a router. While this is non- optimal for situations where bandwidth is highly managed, it was acceptable when a few paths are required in a primarily connectionless environment; if a large number of coordinated paths are required, it is advantageous to have a more sophisticated path computation engine capable of optimizing the path routing of a sub network. The path computation could take the form of paths being computed either on a management station with local computation for rerouting or more sophisticated Path computation servers. Path computation in GMPLS generates explicit route objects (EROs) that can be used directly by GMPLS signaling. The implication is that the TE database and path computation engine may not be co- located with the Ethernet LSR. 10.1.8 Combinations of GMPLS Features The combinations of LMP, Routing, Signaling and Path computation can be all supported on a switch or a subset of GMPLS features can be supported. Signaling is the minimal function that might be supported on a small switch. The ability to process Signaling messages with an ERO may be all that is desired on an end point. In this case the path computation would be performed off network. Routing for GMPLS is the next important function since it provides the forwarding of signaling functions and transport of TE information. There is no requirement to provide full IP routing for data traffic, only hop by hop routing for the control plane. However it is possible to design switches without routing that could proxy their routing to other larger switches. In the proxied case, there would be little difference in the routing database but the small switches would not have to perform routing operations. The information for the proxied routing might be configured or it might be data filled by an automated procedure. No new protocols are envisioned for the case where routing is proxied. LMP is optional as mentioned earlier. The primary benefit of LMP in addition to 802.1AB is LMP's capability to optimize routing information for the purpose of link bundling on large switches. LMP has the capability to compress the information required to represent Fedyk et al. Expires December 2006 Page 17 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt a large number of parallel resources automatically and reduce the amount of configuration. 10.2 Addresses, Interfaces, and Labels This specification uses an addressing scheme and a label space for the ingress/egress connection; the hierarchical GMPLS Switch Address/Port ID and the Ethernet VID/DMAC tuple or VID/Multicast MAC as a label space. GMPLS Switch Address | V N=named port +----+ +-----+ | | label=VLAN/MAC | | | PB | label=VID/MMAC | | -----N N----------------------------N PBB N---------- | | |(MAC)| \ | | / | Externally +----+ /+-----+ Facing PBT Transit Provider Egress MAC/ PBT edge Ports Switch (Label) Switch Figure 4 Ethernet/GMPLS Addressing & Label Space Depending on how the service is defined and set up one or more of these identifiers may be used for actual setup. Also note that although it is possible for a terminating switch to offer any 60 bit label value that can be guaranteed to be domain wide unique, the convention of using MAC addresses to name specific ports is retained. An Ethernet port name is common to both configured MAC/VID, configured VID and bridging modes of operation. One implication of this is that a port index and a MAC address of a port on the switch may be effectively interchangeable for signaling purposes. For a GMPLS based system, the GMPLS Switch Address/logical port is the logical signaling identifier for the control plane via which Ethernet layer label bindings are solicited. In order to create a point to point path an association must be made between the ingress and egress node. But the actual label distributed via signaling and instantiated in the switch forwarding tables identifies the egress MAC of the PBT tunnel (see Figure 4). This label may be the same as the externally facing port if global labels are used or it may be an internal provider hidden domain wide label. GMPLS uses identifiers in the form of 32 bit numbers which are in the IP address notation but these are not IP addresses. An IP routing control plane for the propagation of TE information may be supported. The provider MAC addresses are exchanged by the LLDP and by LMP if supported. Actual label assignment is performed by the signaling initiator and terminator. Fedyk et al. Expires December 2006 Page 18 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt A particular port on a provider network switch would have: - A MAC - A 32 bit IPv4 Switch address or 128 bit IPv6 address plus 32 bit port Identifier - One (or more) Mnemonic String Identifiers This multiple naming convention leaves the issue of resolving the set given one of the port identifiers. On a particular node, mapping is relatively straight forward. The preferred solution to this is to use the GMPLS IP switch address for signaling resolution. In so doing, the problem of setting up a path is reduced to figuring out what switch supports a egress MAC address and then finding the corresponding GMPLS IP switch address and performing all signaling and routing with respect to the GMPLS switch address. There are several options to achieve this: - Provisioning - Auto discovery protocols that carry MAC address - Augmenting Routing TE with MAC Addresses - Name Servers with identifier/address registration This will be clarified in a subsequent version of this document. 11. Specific Procedures 11.1 PT to PT connections The Data Plane for IVL has three key fields: VID, DMAC and SMAC. A connection instance is uniquely identified by the DMAC, the VID and the SMAC for the purpose of the provider network terminations. The VID and DMAC tuple identifies the forwarding multiplex at transit switches and a simple degenerate form of the multiplex is P2P (only one SMAC/VID/DMAC connection uses the VID/DMAC tuple). This results in unique labels end to end and no merging or multiplexing of tunnels. The data streams may merge but the forwarding entries are unique allowing the connection to be de- multiplexed downstream. 11.2 P2P connections with shared forwarding The VID/DMAC can be considered to be a shared forwarding identifier or label for a multiplex consisting of some number of P2P connections distinctly identified by the MAC SMAC/VID/DMAC tuple. The reason for using a shared forwarding entry is it reuses existing labels. VLAN tagged Ethernet packets include priority marking. Priority bits can be used to indicate class of Service (COS) and drop priority. Thus, traffic from multiple COSs could be multiplexed on the same ESP (i.e., similar to E-LSPs) and queuing and drop decisions are made based on the p-bits. This means that the queue selection can be done Fedyk et al. Expires December 2006 Page 19 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt based on a per flow (i.e., ESP + priority) basis and is decoupled from the actual steering of the packet at any given node. A terminating switch will frequently have more than one suitable candidate path may choose to share a forwarding entry.(common VID/DMAC , unique SMAC). It is a local decision of how this is performed but the best choice is a path that maximizes the shared forwarding. The concept of bandwidth management still applies with equally well with shared forwarding. As an example consider a PBT edge switch that terminates an Ethernet LSP with the following attributes: bandwidth B1, DMAC D, SMAC S1, VID V. A request to establish an additional Ethernet LSP with attributes (bandwidth B2, DMAC D, SMAC S2, VID V) can be accepted provided there is sufficient link capacity remaining. 11.2.1 Dynamic P2P symmetry with shared forwarding Similar to how a destination switch may select a VID/DMAC from the set of existing shared forwarding multiplexes rooted at the destination node, the originating switch may also do so for the reverse path. Once the initial ERO has been computed and the set of existing Ethernet LSPs that include the target DMAC have been pruned, the originating switch may select the optimal (by whatever criteria) existing shared forwarding multiplex for the new destination to merge with and offer its own VID/DMAC tuple for itself as a destination. This is identified via use of the UPSTREAM LABEL object. 11.2.2 Planned P2P symmetry Normally the originating switch will not have knowledge of the set of shared forwarding paths rooted on the destination node. Use of a Path Computation Server or other planning style of tool with more complete knowledge of the network configuration may wish to impose pre-selection of shared forwarding multiplexes to use for both directions (Dave: Does this correct the typo). In this scenario the originating switch uses the SUGGESTED LABEL and UPSTREAM LABEL objects to indicate complete selection of the shared forwarding multiplexes at both ends. This may also result in the establishment of a new VID/DMAC path as the SUGGESTED LABEL object may legitimately refer to a path that does not yet exist. 11.2.3 Path Maintenance Make before break procedures can be employed to modify the characteristics of a P2P Ethernet LSP. As described in [RSVP-TE], the LSP ID in the sender template is updated as the new path is signaled. The procedures (including those for shared forwarding) are identical to those employed in establishing a new LSP, with the extended tunnel ID in the signaling exchange ensuring that double booking of the associated resources does not occur. Fedyk et al. Expires December 2006 Page 20 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt Where individual paths in a protection group are modified, signaling procedures may be combined with PS coordination to administratively force PS switching operations such that modifications are only ever performed on the protection path. 11.3 P2MP VID/MAC Connections 11.3.1 Setup procedures The multicast DMAC is administered from a central pool of multicast addresses and the VLAN selected from the configured VID/MAC range. The P2MP tree is constructed via incremental addition of leaves to the tree in signaling exchange where the root is the originating switch (as per (MPLS-P2MP). The multicast DMAC and VID are encoded in the suggested label object using the Ethernet label encoding. Where a return path is required the unicast MAC corresponding to the originating interface and a VID selected from the configured VID/MAC range is encoded as an Ethernet label in the upstream label object. 11.3.2 Maintenance Procedures Maintenance and modification to a P2MP tree can be achieved by a number of means. The preferred technique being to modify existing VLAN configuration vs. assignment of a new label and completely constructing a new tree. Make before break on a live tree reusing existing label assignments requires a 1:1 or 1+1 construct. The protection switch state of the traffic is forced on the working tree and locked (PS not allowed) while the backup tree is modified. Explicit path tear of leaves to be modified is required to ensure no loops are left behind as artifacts of tree modification. Once modifications are complete, a forced switch to the backup tree occurs and the original tree may be similarly modified. This also suggests that 1+1 or 1:1 resilience can be achieved for P2MP trees for any single failure (switch on any failure and use restoration techniques to repair the failed tree). 11.4 P2MP VID Trees 11.4.1 Setup Procedures The VID is administered from the central pool of VLAN IDs corresponding to the configured VID range. The P2MP VID tree is constructed via incremental addition of leaves to the tree in signaling exchange where the root is the originating switch as per [MPLS-P2MP]. Where (*,*) connectivity is to be configured a single VID is employed and encoded as an Ethernet label in the suggested label object with MAC address set to zero. Fedyk et al. Expires December 2006 Page 21 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt Where communication is to be constrained to root to leaves and leaves to root only, asymmetrical VID configuration is used with the suggested label object encoding the root to leaf VID and the upstream label object encoding the leaf to root VID. 11.4.2 Maintenance procedures Maintenance and modification to a P2MP VID tree can be achieved by a number of means. The preferred technique being to move traffic off the tree, modify the tree and then shift traffic back to the tree. This ensures that there are no transient loops in the tree that are artifacts of interactions of the GMPLS control plane, soft state and the Ethernet data plane. Make before break on a live tree requires a 1:1 or 1+1 construct. The protection switch state of the traffic is forced on the working tree and locked (PS not allowed) while the backup tree is modified. Explicit path tear of leaves to be modified is required to ensure no loops are left behind as artifacts of tree modification. Once modifications are complete, a forced switch to the backup tree occurs and the original tree may be similarly modified. This also suggests that 1+1 or 1:1 resilience can be achieved for P2MP trees for any single failure (switch on any failure and use restoration techniques to repair the failed tree). 11.5 OAM MEP ID and MA ID synchronization The Maintenance end point IDs (MEP IDs) and maintenance association IDs for the switched path endpoints can be synchronized using the ETH-MCC (maintenance communication channel) transaction set once the switched path has been established. MEPs are located at the endpoints of the Ethernet LSP. Typical configuration associated with a MEP is Maintenance Domain Name, Short Maintenance Association Name, and MA Level, MEP ID, and CCM transmission rate (when ETH-CC functionality is desired). As part of the synchronization, it is verified that the Maintenance Domain Name, Short Maintenance Association Name, MA Level, and CCM transmission rate are the same. It is also determined that MEP IDs are unique for each MEP. Server MEPs can be considered at the intermediate points of the PBT network. Upon network failures (e.g. physical link failures), the Server MEPs can initiate the unicast AIS frames for each Ethernet LSP end-point that is present in the forwarding table. The only configuration required at the Server MEPs is the MA Level which should be the same as the MA Level configured at the Ethernet LSP MEPs. Besides the unicast CCM and AIS functionality, the PBT MEPs can also offer the LBM/LBR and LMM/LMR functionalities for on-demand connectivity verification and loss measurement purposes. Fedyk et al. Expires December 2006 Page 22 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt 11.6 Protection Paths When protection is used for path recovery it is required to associate the working and protection paths into a protection group. This is achieved as defined in [RECOVERY_SIG] using the ASSOCIATION and PROTECTION objects. Protection may be used for P2P VID/MAC, P2MP VID/MAC and P2MP VID configured modes of operation. The 'P' bit in the protection object indicates the role (working or protection) of the LSP currently being signaled. If the initiating switch wishes to use G.8031 [G-8031] data plane protection switching coordination (vs. control plane notifications), it sets the N bit to 1 in the protection object. This must be consistently applied for all paths associated as a protection group. If the terminating switch does not support G.8031, the error "Admission Control Failure/Unsupported Notification Type" is used. 12. Error conditions The following errors have been identified as being unique to these procedures and in addition to those already defined. This will be addressed in a proper IANA considerations section in a future version of the document: 12.1 Invalid VID value for configured VID/MAC range The originator of the error is not configured to use the VID value in conjunction with GMPLS signaling of VID/MAC tuples. This may be any switch along the path. 12.2 Invalid VID value for configured VID range 12.3 Invalid MAC Address 12.4 Invalid ERO for Upstream Label Object The ERO offered has discontinuities with the identified VID/MAC path in the UPSTREAM LABEL object. 12.5 Invalid ERO for Suggested Label Object The ERO offered has discontinuities with the identified VID/MAC path in the SUGGESTED LABEL object. 12.6 Switch is not IVL capable 12.7 Switch is not SVL capable 12.8 Switch is not Asymmetric VID capable Fedyk et al. Expires December 2006 Page 23 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt 12.9 Invalid VID in upstream label object The VID in the upstream label object for the "asymmetrical VID" P2MP tree did not correspond to the VID used in previous transactions. 13. Security Considerations The architecture assumes that the GMPLS controlled Ethernet subnet consists of trusted devices and that the UNI ports to the domain are untrusted. Care is required to ensure untrusted access to the trusted domain does not occur. Where GMPLS is applied to the control of VLAN only, the commonly known techniques for mitigation of Ethernet DOS attacks may be required on UNI ports. 14. IANA Considerations New values are required for signaling and error codes as indicated. This section will be completed in a later version. 15. References 15.1 Normative References [CCAMP-ETHERNET] Papadimitriou, D. et.al, "A Framework for Generalized MPLS (GMPLS) Ethernet", internet draft, draft- papadimitriou-ccamp-gmpls-ethernet-framework-00.txt , June 2005 [GMPLS-SIGNALING] Berger, L. (editor), "Generalized MPLS -Signaling Functional Description", January 2003, RFC3471. [GMPLS-ROUTING] Kompella, K., Rekhter, Y., "Routing Extensions in Support of Generalized MPLS", RFC 4202, October 2005 [GMPLS-RSVP] Berger, L. et.al., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) Extensions", IETF RFC 3473, January 2003. 15.2 Informative References [DS-COLOR] Aboul-Magd, O. et.al. "A Differentiated Service Two-Rate, Three-Color Marker with Efficient Handling of in-Profile Traffic", IETF RFC 4115, July 2005 [G-8031] ITU-T Draft Recommendation G.8031, Ethernet Protection Switching. [GMPLS-ARCH] E. Mannie, Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Architecture", RFC 3495. [IEEE 802.1ab] "IEEE Draft Standard for Local and Metropolitan Area Networks, Station and Media Access Control Connectivity Discovery". Fedyk et al. Expires December 2006 Page 24 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt [IEEE 802.1ag] "IEEE standard for Connectivity Fault Management", work in progress. [IEEE 802.1ah] "IEEE standard for Provider Backbone Bridges", work in progress. [LMP] Lang. J. Editor, "Link Management Protocol (LMP)" work in progress. [MEF.6] The Metro Ethernet Forum MEF 6 (2004), "Ethernet Services Definitions - Phase I". [MEF.10] The Metro Ethernet Forum MEF 10 (2004), "Ethernet Services Attributes Phase 1". [MPLS-DS] Le Faucheur, F. et.al., "Multi-Protocol Label Switching (MPLS) Support of Differentiated Services" IETF RFC 3270, May 2002. [MPLS-P2MP] Aggarwal, R. Ed., "Extensions to RSVP-TE for Point to Multipoint TE LSPs", work in progress. [MYERS] Myers et.al. "Rethinking the service model, scaling Ethernet to a million nodes", http://100x100network.org/papers/myers- hotnets2004.pdf. [PATH-COMP] Farrel, A. et.al., "Path Computation Element (PCE) Architecture", work in progress. [PWoPBT] Allan et.al., "Pseudo Wires over Provider Backbone Transport", draft-allan-pw-o-pbt-00.txt, work in progress. [PWE] Bryant, S., Pate, P. et al., "Pseudo Wire Emulation Edge-to Edge (PWE3) Architecture", IETF RFC 3985, March 2005. [RECOVERY_SIG] Lang et.al., "RSVP-TE Extensions in support of End- to-End Generalized Multi-Protocol Label Switching (GMPLS)-based Recovery ", work in progress. [RSVP-TE] Awduche et.al., "RSVP-TE: Extensions to RSVP for LSP Tunnels, IETF RFC 3209, December 2001. [Y.1731] ITU-T Draft Recommendation Y.1731(ethoam), " OAM Functions and Mechanisms for Ethernet based Networks ", work in progress. 16. Author's Address Don Fedyk Nortel Networks 600 Technology Park Drive Phone: +1-978-288-3041 Billerica, MA, 01821 Email: dwfedyk@nortel.com Fedyk et al. Expires December 2006 Page 25 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt David Allan Nortel Networks Phone: +1-613-763-6362 3500 Carling Ave. Email: dallan@nortel.com Ottawa, Ontario, CANADA Greg Sunderwood Bell Canada Phone: +1-604-648-7770 Suite 1500, Email: greg.sunderwood@gt.ca 1066 West Hastings Street Vancouver, BC, CANADA V6E 2X1 Himanshu Shah Ciena Phone: 978-489-2196 35 Nagog Park, Email: hshah@ciena.com Acton, MA 01720 17. Intellectual Property Statement The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. 18. Disclaimer of Validity This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Fedyk et al. Expires December 2006 Page 26 Internet Draft draft-fedyk-gmpls-ethernet-pbt-00.txt 19. Copyright Statement Copyright (C) The Internet Society (2006). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. 20. Acknowledgments The authors would like to thank Dinesh Mohan, Nigel Bragg, Stephen Shew and Sandra Ballarte for their extensive contributions to this document. Fedyk et al. Expires December 2006 Page 27