SIPPING                                                         M. Dolly
Internet-Draft                                                 AT&T Labs
Expires: January 13, 2005                                  July 15, 2004


            Data Content for SIP User Agent Profile Delivery
               draft-dolly-sipping-config-content-01.txt

Status of this Memo

   This document is an Internet-Draft and is in full conformance with
   all provisions of Section 10 of RFC2026.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups. Note that other
   groups may also distribute working documents as Internet-Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time. It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at http://
   www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on January 13, 2005.

Copyright Notice

   Copyright (C) The Internet Society (2004). All Rights Reserved.

Abstract

   This document defines the data content for providing profile data to
   SIP user agents in support of the framework defined in
   I-D.ietf-sipping-config-framework-03.txt and is intended to be input
   to the data sets defined by
   draft-petrie-sipping-profile-datasets-00.txt..


Conventions used in this document

   RFC2119 [1] provides the interpretations for the key words "MUST",
   "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT",
   "RECOMMENDED", "MAY", and "OPTIONAL" found in this document.




Dolly                   Expires January 13, 2005                [Page 1]

Internet-Draft               Config Content                    July 2004


   I-D.ietf-sipping-config-framework-02.txt [6] provides the
   interpretations for the terms "profile", "device", "profile content
   server", "notifier", and "profile delivery server".

Table of Contents

   1.   Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
   2.   Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
   3.   Data Content . . . . . . . . . . . . . . . . . . . . . . . . . 3
   4.   Data Set Examples  . . . . . . . . . . . . . . . . . . . . . . 6
   5.   IANA Considerations  . . . . . . . . . . . . . . . . . . . . . 6
   6.   Security Considerations  . . . . . . . . . . . . . . . . . . . 6
   7.   Open Issues  . . . . . . . . . . . . . . . . . . . . . . . . . 7
   8.   Change History . . . . . . . . . . . . . . . . . . . . . . . . 7
   9.   Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
   10.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 7
   10.1   Normative References . . . . . . . . . . . . . . . . . . . . 7
   10.2   Informative References . . . . . . . . . . . . . . . . . . . 7
        Author's Address . . . . . . . . . . . . . . . . . . . . . . . 8
   A.   Contributors . . . . . . . . . . . . . . . . . . . . . . . . . 8
   B.   Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 8
        Intellectual Property and Copyright Statements . . . . . . . . 9





























Dolly                   Expires January 13, 2005                [Page 2]

Internet-Draft               Config Content                    July 2004


1.  Introduction

   This document defines the data content for providing profile data to
   SIP user agents in support of the framework defined in
   I-D.ietf-sipping-config-framework-02.txt [6]. The current framework
   draft identifies two types of profiles, defined as "user" and
   "device". It is anticipated, per discussion at the previous meeting,
   that the draft 03 version will define a profile for "local".

   The profile delivery framework is intended to enable a first phase
   migration to a standard means of providing profiles to SIP user
   agents. It is expected that UA vendors willbe able to use this
   framework as a means of delivering their existing proprietary user
   and device data profiles.

2.  Overview

   The three types of content to be defined are user, device and local.
   The profile delivery server will provide the content or URI(s)
   associated with the user and device profiles. The local profile is
   optional and its content will be provided by the local domain serving
   the SIP User Agent.

   The content of the device profile is a function of the vendor, model,
   and version parameters associted with the device, which are specified
   by the vendor of the user agent. These parameters allow the profile
   delivery server to provide different profiles based upon these
   variables.

   As noted in the framework, a default user maybe assigned to a device.
   In this scenario the profile delivery server may provide the URI(s)
   in the NOTIFY request for the default user when subscribing to the
   device profile type. Effectively the device profile type becomes a
   superset of the user profile subscription. The user type is still
   useful in this scenario to allow the user agent to obtain profile
   data or URI(s) for a user other than the default user. This provides
   the ability to support a hoteling function where a user may "login"
   to a local domain and obtain the content of the local profile.

3.  Data Content

   The data content list below is intended as input into the datasets to
   be defined in draft-petrie-sipping-profile-datasets-00.txt.

   The local data may be inputted by the subscriber or the local access
   domain.

   Elements of the User Data include:



Dolly                   Expires January 13, 2005                [Page 3]

Internet-Draft               Config Content                    July 2004


      -- Proxy and Registration Server URIs - IP addresses of the
      primary SIP proxyand registration servers that will be used.
      (address format is the in IP dotted-decimal notation)

      --Preloaded Route Set

      -- User Address of Record and Display Name - A user'sline
      represents an address-of-record identified by a URL There are many
      properties which may be associated with or should be applied to
      the line or signaling addressed to or from the line. The display
      name is the identifiation as it should appear for the Caller ID
      associated with the user.

      -- User Authentication Information and Other Credentials -
         Authentication name - name used by the device for authenication
         if a registration is challenged.
         Authenication Password - Password used by the device for
         athentication. The device may have a default logical password
         (e.g., MAC IP address).

      -- Privacy Settings - calling party presentation restriction.

      -- Pre Media Configuration Parameters (e.g., Audio Configuration)

      -- Dial Plan - A dial plan which defines the maximum expected
      length of a typical telephone. Zero or more digit maps that map a
      dial plan and a SIP address to which phone numbers of the type
      should be routed. The digit maps define numeric patterns that when
      matched define:
         1) a rule by which the end point has to judge that the user has
         completed dialing;
         2) a rule to construct a URL from the dialed digits;
         3) Optionally, an outbound proxy to be used in routing the SIP
         INVITE.
         Note: Intra-Digit and Howler tone timers are associated with
         the dial plan.
         The end point must support the configuration of a default digit
         map.
         Some operators support overlap dialing and may want the SIP
         device to operate in that mode.

      -- Progess Tone Settings - These include confirmation, reorder,
      and "ring-ping" type tones.

      -- ENUM Settings - IP address and port address of ENUM server.

      -- International Settings - This may include language preference,
      and default server addreses.



Dolly                   Expires January 13, 2005                [Page 4]

Internet-Draft               Config Content                    July 2004



      -- Call Forwarding and Redirection Settings - contains the forward
      to/redirection addresses, conditions of forwarding/redirection,
      and methiods used to forward/redirect.

      -- Speed Dial Settings - users speed dial numbers and associated
      device keys.

      -- Local Control Feature Settings (e.g., transfer, conference) -

      -- Alert Settings, including pre-caller alerting - The manner in
      which a user is alerted to an incoming call (visually, audibly, or
      possibly both) used by a device. This includes different volumes
      and melodies. There may be a pointer to a file to obtain the
      melody. Ringer sound files may be specified to alert the user to
      the type of incoming call (e.g., normal, high priority, internal,
      external).

      -- URIs and timers for additional profile configuration - contains
      URIs of functional specific servers (e.g., Voice Mail, Phonebook,
      Directory).
      -- Logging Settings

      -- Firmware Upgrade

      -- Response Status Code Handling - mapping of response status
      codes to device final handling treatment (e.g., tones and
      annoucements).

      -- Protocol Data Sets - Contains SIP extensions, body types,
      transport protocols (UDP, TCP, TLS, SCTP) or external protocols
      (e.g., http) that need to be supported.

      -- Media Data Set - This includes Codec DATA set, maximum number
      of streams, allowed bandwidth per stream, IPaddresses/ports, etc.

      -- RTP Parameters

         RTP Port Range - A range of port numbers used by a device for
         the consecutive pairs of ports that are used to receive audio
         and ontrol information (RTP and RCTP) for each concurrent
         connection.

      -- SDP Payload Types

      -- Audio Configurations





Dolly                   Expires January 13, 2005                [Page 5]

Internet-Draft               Config Content                    July 2004


      -- Firewall and NAT Support Parameters

         NAT Address - WAN IP address of the NAT or firewall server. A
         network address (such as an IP address) used by a device to
         make calls through a NAT. The device includes this IP address
         in the SIP messages and SDP it sends to the other SIP agents to
         indicate that this is the adddress to which SIP, RTP, and RTCP
         packets are be sent. This supports the case where the NAT is
         configured to statically map specific ports on hte external
         interface to a specific end point in side the NAT. The end
         point in turn is configured to spoof other SIP entities into
         thinking it is the external interface on the NAT.

      Manual Network Addressing

      Local Administration Settings

4.  Data Set Examples

   Telephony Prompts, Tones and Final Handling:
      Audio Configurations
      Alert Settings
      International Settings (or at least tones)
      Progess Tone Settings
      Pre Media Configuration Parameters
      Response Status Code Handling

5.  IANA Considerations

   This document introduces no requirements for IANA.

6.  Security Considerations

   Profiles may contain sensitive data such as user credentials. The
   protection of this data depends upon how the data is delivered. If
   the data is delivered in the NOTIFY body, SIP authentication MUST be
   used for SUBSCRIPTION and SIPS and/or S/MIME MAY be used to encrypt
   the data. If the data is provided via content indirection, SIP
   authentication is not necessary for the SUBSCRIBE request. With
   content indirection the data is protected via the authentication,
   authorization and encryption mechanisms provided by the profile URL
   scheme. Use of the URL scheme security mechanisms via content
   indirection simpifies the security solution as the SIP event package
   does not need to authenticate, authorize or protect the contents of
   the SIP messages. Effectively the profile delivery server will
   provide profile URL(s) to anyone. The URLs themselves are protected
   via authentication, authorization and snooping (e.g., via HTTPS).




Dolly                   Expires January 13, 2005                [Page 6]

Internet-Draft               Config Content                    July 2004


7.  Open Issues

   This section identifies issues yet to be addressed.

8.  Change History

   This section identifies changes to the document per draft revision.

9.  Examples

   This section is informative in nature.  If there is a discrepancy
   between this section and the normative sections above, the normative
   sections take precedence.

10.  References

10.1  Normative References

   [1]  Bradner, S., "Key words for use in RFCs to Indicate Requirement
        Levels", BCP 14, RFC 2119, March 1997.

   [2]  Murata, M., St. Laurent, S. and D. Kohn, "XML Media Types", RFC
        3023, January 2001.

   [3]  Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston, A.,
        Peterson, J., Sparks, R., Handley, M. and E. Schooler, "SIP:
        Session Initiation Protocol", RFC 3261, June 2002.

   [4]  Roach, A., "Session Initiation Protocol (SIP)-Specific Event
        Notification", RFC 3265, June 2002.

   [5]  Daigle, L., van Gulik, D., Iannella, R. and P. Faltstrom,
        "Uniform Resource Names (URN) Namespace Definition Mechanisms",
        BCP 66, RFC 3406, October 2002.

10.2  Informative References

   [6]   Petrie, D., "A Framework for SIP User Agent Profile Delivery",
         draft-ietf-sipping-config-framework-02.txt (work in progress),
         February 2004.

   [7]   Rosenberg, J., "Obtaining and Using Globally Routable User
         Agent (UA) URIs (GRUU) in the  Session Initiation Protocol
         (SIP)", draft-ietf-sip-gruu-01 (work in progress), February
         2004.

   [8]   Fielding, R., Gettys, J., Mogul, J., Nielsen, H., Masinter, L.,
         Leach, P. and T. Berners-Lee, "Hypertext Transfer Protocol --



Dolly                   Expires January 13, 2005                [Page 7]

Internet-Draft               Config Content                    July 2004


         HTTP/1.1", RFC 2616, June 1999.

   [9]   Bray, T., Paoli, J., Sperberg-McQueen, C. and E. Maler,
         "Extensible Markup Language (XML) 1.0 (Second Edition)", W3C
         REC REC-xml-20001006, October 2000.

   [10]  Rosenberg, J. and H. Schulzrinne, "An INVITE Inititiated Dialog
         Event Package for the Session Initiation  Protocol (SIP",
         draft-ietf-sipping-dialog-package-02 (work in progress), June
         2003.


Author's Address

   Martin Dolly
   AT&T Labs

   EMail: mdolly@att.com

Appendix A.  Contributors

   Many thanks to Rohan Mahy for for his input and guidance.

Appendix B.  Acknowledgements

   Thanks to Eric Burger on the use of the XML tools.

























Dolly                   Expires January 13, 2005                [Page 8]

Internet-Draft               Config Content                    July 2004


Intellectual Property Statement

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights. Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in BCP-11. Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard. Please address the information to the IETF Executive
   Director.


Full Copyright Statement

   Copyright (C) The Internet Society (2004). All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works. However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assignees.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION



Dolly                   Expires January 13, 2005                [Page 9]

Internet-Draft               Config Content                    July 2004


   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.


Acknowledgment

   Funding for the RFC Editor function is currently provided by the
   Internet Society.











































Dolly                   Expires January 13, 2005               [Page 10]