INTERNET-DRAFT Patrice Brissette Intended Status: Proposed Standard Ali Sajassi Luc Andre Burdet Cisco Systems Daniel Voyer Bell Canada Expires: September 12, 2019 March 11, 2019 EVPN Multi-Homing Mechanism for Layer-2 Gateway Protocols draft-brissette-bess-evpn-l2gw-proto-04 Abstract The existing EVPN multi-homing load-balancing modes defined are Single-Active and All-Active. Neither of these multi-homing mechanisms are appropriate to support access networks with Layer-2 Gateway protocols such as G.8032, MPLS-TP, STP, etc. These Layer-2 Gateway protocols require a new multi-homing mechanism defined in this draft. Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html Copyright and License Notice Patrice Brissette Expires September 12, 2019 [Page 1] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 Copyright (c) 2019 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Terminology . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 The two-ESI solution . . . . . . . . . . . . . . . . . . . . 5 2.2 Single-Flow-Active redundancy mode . . . . . . . . . . . . . 6 2.3 Backwards compatibility . . . . . . . . . . . . . . . . . . 6 3. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 7 4. Handling of Topology Change Notification (TCN) . . . . . . . . 8 5. ESI-label Extended Community Extension . . . . . . . . . . . . 9 6. EVPN MAC-Flush Extended Community . . . . . . . . . . . . . . . 9 7. EVPN Inter-subnet Forwarding . . . . . . . . . . . . . . . . . 10 8. Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . 10 9. Security Considerations . . . . . . . . . . . . . . . . . . . 11 10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 11 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 11 12. References . . . . . . . . . . . . . . . . . . . . . . . . . 11 12.1 Normative References . . . . . . . . . . . . . . . . . . . 11 12.2 Informative References . . . . . . . . . . . . . . . . . . 11 Patrice Brissette Expires September 12, 2019 [Page 2] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 1. Introduction Existing EVPN multi-homing mechanisms of Single-Active and All-Active are not sufficient to support access Layer-2 Gateway protocols such as G.8032, MPLS-TP, STP, etc. These Layer-2 Gateway protocols require that a given flow of a VLAN (represented by {MAC-SA, MAC-DA}) to be only active on one of the PEs in the multi-homing group. This is in contrast with Single-Active redundancy mode where all flows of a VLAN are active on one of the multi-homing PEs and it is also in contrast with All-Active redundancy mode where all L2 flows of a VLAN are active on all PEs in the redundancy group. This draft defines a new multi-homing mechanism "Single-Flow-Active" which defines that a VLAN can be active on all PEs in the redundancy group but a single given flow of that VLAN can be active on only one of the PEs in the redundancy group. In fact, the carving scheme, performed by the DF(Designated Forwarder) election algorithm for these L2 Gateway protocols, is not per VLAN but rather for a given VLAN. A selected PE in the redundancy group can be the only Designated Forwarder for a specific L2 flow but the decision is not taken by the PE. The loop-prevention blocking scheme occurs in the access network. EVPN multi-homing procedures need to be enhanced to support Designated Forwarder election for all traffic (both known unicast and BUM) on a per L2 flow basis. This new multi-homing mechanism also requires new EVPN considerations for aliasing, mass-withdraw, fast- switchover and [EVPN-IRB] as described in the solution section. 1.1 Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 1.2 Acronyms AC : Attachment Circuit BUM : Broadcast, Unknown unicast, Multicast DF : Designated Forwarder GW : Gateway L2 Flow : a given flow of a VLAN, represented by (MAC-SA, MAC-DA) L2GW : Layer-2 Gateway G.8032 : Ethernet Ring Protection MST-AG : Multi-Spanning Tree Access Gateway REP-AG : Resilient Ethernet Protocol Access Gateway Patrice Brissette Expires September 12, 2019 [Page 3] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 TCN : Topology Change Notification Patrice Brissette Expires September 12, 2019 [Page 4] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 2. Solution +---+ |CE4| +---+ | | +-----+ | PE3 | +-----+ +-----------------+ | | | MPLS/IP | | CORE | | | +-----------------+ +-----+ +-----+ | PE1 | | PE2 | +-----+ +-----+ AC1| |AC2 | | +---+ +---+ |CE1| |CE3| +---+ +---+ | | | +---+ | +----|CE2|----/---+ +---+ Figure 1 EVPN network with L2 access GW protocols Figure 1. shows a typical EVPN network with an access network running a L2GW protocol, typically one of the following: G.8032, STP, MPLS- TP, etc. The L2GW protocol usually starts from AC1 (on PE1) up to AC2 (on PE2) in an open "ring" manner. AC1 and AC2 interfaces of PE1 and PE2 are participants in the access protocol. The L2GW protocol is used for loop avoidance. In above example, the loop is broken on the right side of CE2. 2.1 The two-ESI solution As background, an alternative solution which achieves some, but not all, of the requirements exists and is backwards compatible with [RFC7432]: On the PE1 and PE2, a) A single-homed non-zero ESI is used for each PE; Patrice Brissette Expires September 12, 2019 [Page 5] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 b) With no remote Ethernet-Segment routes received matching local ESI, each PE will be designated forwarder for all the local VLANs; c) Each L2GW PE will send Ethernet AD per-ES and per-EVI routes for its ESI; and d) When the L2GW PEs receive a MAC-Flush notification (STP TCN, G.8032 mac-flush, TLDP MAC withdrawal etc.), they send an update of the Ethernet AD per-EVI route with the MAC Mobility extended community defined in section 6 and a higher sequence number. 2.2 Single-Flow-Active redundancy mode PE1 and PE2 are peering PEs in a redundancy group, and sharing a same ESI. In the proposed Single-Flow-Active mode, PE1 and PE2 'Access Gateway' load-balancing mode shares similarities with both Single- Active and All-Active. DF election must not result in blocked ports or portions of the access may become isolated. Additionally, the reachability between CE1/CE2 and CE3 is achieved with the forwarding path through the EVPN MPLS/IP core side. Thus, the ESI-Label filtering of [RFC7432] is disabled for Single-Flow-Active Ethernet segments. Finally, PE3 behaves according to EVPN rules for traffic to/from PE1/PE2. Peering PE, selected per L2 flow, is chosen by the L2GW protocol in the access, and is out of EVPN control. From PE3 point of view, some of the L2 flows coming from PE3 may reach CE3 via PE2 and some of the L2 flows may reach CE1/CE2 via PE1. A specific L2 flow never goes to both peering PEs. Therefore, aliasing cannot be performed by PE3. That node operates in a single- active fashion for each of these L2 flows. The backup path which is also setup for rapid convergence, is not applicable here. For example, in Figure 1, if a failure happens between CE1 and CE2, L2 flows coming from CE4 behind PE3 destined to CE1 still goes through PE1 and shall not switch to PE2 as a backup path. On PE3, there is no way to know which L2 flow specifically is affected. During the transition time, PE3 may flood until unicast traffic recovers properly. 2.3 Backwards compatibility A PE which receives an Ethernet AD per ES route with the Single-Flow- Active bit set in the ESI-flags, and which does not support/understand this bit, SHALL discard the bit and continue operating per [RFC7432] (Single-Active or All-Active). The operator should understand the usage of single-flow-active load-balancing mode else it is highly recommended to use the two-ESI approach as described in section 2.1. Patrice Brissette Expires September 12, 2019 [Page 6] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 3. Requirements The EVPN L2GW framework for L2GW protocols in Access-Gateway mode, consists of the following rules: o Peering PEs MUST share the same ESI. o The Ethernet-Segment DF election MUST NOT be performed and forwarding state MUST be dictated by the L2GW protocol. In Access Gateway mode, both PEs are usually in forwarding state. In fact, access protocol guarantees drive that state. o Split-horizon filtering is NOT needed because L2GW protocol ensures there will never be loop in the access network. The forwarding between peering PEs MUST also be preserved. In figure 1, CE1/CE2 device may need reachability with CE3 device. ESI- filtering capability MUST be disabled. PE MUST NOT advertise corresponding ESI-label to other PEs in the redundancy group, or apply it if it is received. o ESI-label BGP-extcomm MUST support a new multi-homing mode named "Single-Flow-Active" corresponding to the single-active behaviour of [RFC7432], applied per flow. o Upon receiving ESI-label BGP-Extcomm with the single-flow-active load-balancing mode, remote PE MUST: - Disable ESI-Label processing - Disable aliasing (at Layer-2 and Layer-3 [EVPN-IRB]) o The Ethernet-Segment procedures in the EVPN core such as Ethernet AD per-ES and per Ethernet AD per-EVI routes advertisement/withdraw, as well as MAC and MAC+IP advertisement, remains as explained in [RFC7432] and [EVPN-IRB]. o For fast-convergence, remote PE3 MAY set up two distinct backup paths on a per-flow basis: - { PE1 active, PE2 backup } - { PE2 active, PE1 backup } The backup paths so created, operate as in [RFC7432] section 8.4 where the backup PE of the redundancy group MAY immediately be selected for forwarding upon detection of a specific subset of failures: Ethernet AD per-ES route withdraw, Active PE loss of reachability (via IGP detection). An Ethernet AD per-EVI withdraw MUST NOT result in automatic switching to the backup PE as only a subset of the hosts may be changing reachability to the Backup PE, and the remote cannot determine which. Patrice Brissette Expires September 12, 2019 [Page 7] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 o MAC mobility procedures SHALL have precedence in Single-Flow- Active for tracking host reachability over backup path procedure. 4. Handling of Topology Change Notification (TCN) In order to address rapid Layer-2 convergence requirement, topology change notification received from the L2GW protocols must be sent across the EVPN network to perform the equivalent of legacy L2VPN remote MAC flush. The generation of TCN is done differently based on the access protocol. In the case of STP (REP-AG) and G.8032, TCN gets generated in both directions and thus both of the dual-homing PEs receive it. However, with STP (MST-AG), TCN gets generated only in one direction and thus only a single PE can receive it. That TCN is propagated to the other peering PE for local MAC flushing, and relaying back into the access. In fact, PEs have no direct visibility on failures happening in the access network neither on the impact of those failures over the connectivity between CE devices. Hence, both peering PEs require to perform a local MAC flush on corresponding interfaces. There are two options to relay the access protocol's TCN to the peering PE: in-band or out-of-band messaging. The first method is better for rapid convergence, and requires a dedicated channel between peering PEs. An EVPN-VPWS connection MAY be dedicated for that purpose, connecting the Untagged ACs of both PEs. The latter choice relies on a new MAC flush extended community in the Ethernet Auto-discovery per EVI route, defined below. It is a slower method but has the advantage of avoid the usage of a dedicated channel between peering PEs. Peering PE, upon receiving TCN from access, MUST: o As per legacy VPLS, perform a local MAC flush on the access-facing interfaces. An ARP probe is also sent for all hosts previously locally-attached. o Advertise per EVI/EAD route along with a new MAC-flush BGP Extended Community in order to perform a remote MAC flush and steer L2 traffic to proper peering PE. The sequence number is incremented by one as a flushing indication to remote PEs. o Ensure MAC and MAC/IP route re-advertisement, with incremented Patrice Brissette Expires September 12, 2019 [Page 8] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 sequence number when host reachability is NOT moving to peering PE. This is to ensure a re-advertisement of current MAC and MAC/IP which may have been flushed remotely upon MAC Flush extcomm reception. In theory, it should happen automatically since peering PE, receiving TCN from the access, performs local MAC flush on corresponding interface and will re-learn that local MAC or MAC/IP at ARP probe reply. o Where an access protocol relies on TCN BPDU propagation to all participant nodes, a dedicated EVPN-VPWS connection MAY be used as an in-band channel to relay TCN between peering PEs. That connection may be auto-generated or can simply be directly configured by user. 5. ESI-label Extended Community Extension In order to support the new EVPN load-balancing mode (single-flow- active), the ESI-label extended community is extended. The 1 octet flag field, as part of the ESI-label Extcomm, is updated as follow: Each ESI Label extended community is encoded as an 8-octet value, as follows: 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type=0x06 | Sub-Type=0x01 | Flags(1 octet)| Reserved=0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved=0 | ESI Label | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Low-order bit: [7:0] [2:0]- 000 = all-active, 001 = single-active, 010 = single-flow-active, others = unassigned [7:3]- Reserved 6. EVPN MAC-Flush Extended Community The MAC mobility BGP Extended community, is required for the TCN procedures and MAC-Flushing. The well-known MAC-Flush procedure from [RFC7623] is borrowed, only for Ethernet AD per-EVI routes. In this Single-Flow-Active mode, the MAC-Flush Extended Community is advertised along with Ethernet AD per EVI routes upon reception of TCN from the access. When this extended community is used, it indicates, to all remote PEs that all MAC addresses associated with that EVI/ESI are "flushed" i.e. unresolved. They remain unresolved until remote PE receives a route update / withdraw for those MAC Patrice Brissette Expires September 12, 2019 [Page 9] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 addresses; the MAC may be re-advertised by the same PE, or by another, in the same ESI. The sequence number used is of local significance from the originating PE, and is not used for comparison between peering PEs. Rather, it is used to signal via BGP successive MAC Flush requests from a given PE. 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type=0x06 | Sub-Type=0x?? | Reserved = 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 7. EVPN Inter-subnet Forwarding EVPN Inter-subnet forwarding procedures in [EVPN-IRB] works with the current proposal and does not require any extension. Host routes continue to be installed at PE3 with a single remote nexthop, no aliasing. However, leveraging the same-ESI on both L2GW PEs enables ARP/ND synchronization procedures which are defined for All-Active redundancy in [EVPN-IRB]. In steady-state, on PE2 where a host is not locally-reachable the routing table will reflect PE1 as the destination. However, with ARP/ND synchronization based on a common ESI, the ARP/ND cache may be pre-populated with the local AC as destination for the host, should an AC failure occur on PE1. This achieves fast-convergence. When a hosts moves to PE2 from the PE1 L2GW peer, the MAC mobility sequence number is incremented to signal to remote peers that a 'move' has occurred and the routing tables must be updated to PE2. This is required when an Access Protocol is running where the loop is broken between two CEs in the access and the L2GWs, and the host is no longer reachable from the PE1-side but now from the PE2-side of the access network. 8. Conclusion EVPN Multi-Homing Mechanism for Layer-2 gateway Protocols solves a true problem due to the wide legacy deployment of these access L2GW protocols in Service Provider networks. The current draft has the main advantage to be fully compliant with [RFC7432] and [EVPN-IRB]. Patrice Brissette Expires September 12, 2019 [Page 10] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 9. Security Considerations The same Security Considerations described in [RFC7432] and [EVPN- IRB] remain valid for this document. 10. Acknowledgements Authors would like to thank Thierry Couture for valuable review and inputs with respect to access protocol deployments related to procedures proposed in this document. 11. IANA Considerations A new allocation of Extended Community Sub-Type for EVPN is required to support the new EVPN MAC flush mechanism. 12. References 12.1 Normative References [RFC7432] Sajassi, A., Ed., Aggarwal, R., Bitar, N., Isaac, A., Uttaro, J., Drake, J., and W. Henderickx, "BGP MPLS-Based Ethernet VPN", RFC 7432, DOI 10.17487/RFC7432, February 2015, . 12.2 Informative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . Authors' Addresses Patrice Brissette Cisco Systems EMail: pbrisset@cisco.com Ali Sajassi Cisco Systems EMail: sajassi@cisco.com Luc Andre Burdet Cisco Systems EMail: lburdet@cisco.com Patrice Brissette Expires September 12, 2019 [Page 11] INTERNET DRAFT draft-brissette-bess-evpn-l2gw-proto March 11, 2019 Daniel Voyer Bell Canada EMail: daniel.voyer@bell.ca Patrice Brissette Expires September 12, 2019 [Page 12]