Audio Video Transport Group Internet Draft A. Basso Document: draft-basso-avt-videoconreq-02.txt NMS Communications O.Levin Microsoft N. Ismail Cisco Systems Expires: April 2005 October 2004 Requirements for transport of video control commands Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of RFC 3667 [2]. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of RFC 3668. Abstract A variety of video communication services such as video conferencing and video messaging rely on the capability of video encoders and decoders to respond to control commands. This document outlines this set of commands as well as the requirements for their transport. basso Expires April 2005 [Page 1] Codec Control Requirements October 2004 Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [1]. Table of Contents 1. Introduction...................................................3 2. Background.....................................................3 3. Video coding...................................................3 4. Use Cases......................................................4 5. Codec Commands.................................................5 5.1 Decoder Control Commands...................................5 5.2 Encoder Control Commands...................................6 6. General requirements...........................................6 6.1 Reuse of Existing Protocols................................7 6.2 Maintain Existing Protocol Integrity.......................7 6.3 Avoid Duplicating Existing Protocols.......................7 6.4 Efficiency.................................................7 7. Codec Control Requirements.....................................7 7.1 Reliable and Unreliable Delivery...........................7 7.2 Transport alternatives.....................................8 7.3 Capability description.....................................8 7.4 Relation with media session................................8 7.5 Bidirectional transport....................................8 7.6 Extensibility..............................................8 7.7 Unicast and Multicast Support..............................8 7.8 Timely delivery............................................9 8. Security Considerations........................................9 9. IANA Considerations............................................9 10. Acknowledgments...............................................9 11. Copyright Notice..............................................9 12. Informative References.......................................10 13. IPR Notices..................................................10 Author's Addresses...............................................11 What is new from version 01 1. Document updated to be conformant to Guidelines to Authors of Internet-Drafts 2. Section 5.2.4 RateNotify command removed. 3. Section 7.1 Clarified Reliable versus unreliable delivery. 4. Added Section 7.2 Transport alternatives 5. Section 7.4 Relation with signaling. Removed 6. Section 9.8 Interoperability with other protocols. Removed 7. Section 9.9 MUST has been changed to SHOULD. Basso Expires April 2005 [Page 2] Codec Control Requirements October 2004 8. Updated references What is new from version 00 1. Added boilerplate text. 2. Sec. 3: Clarification of terminology. 3. Sec. 6 : clarification the reference to IETF protocols only. 4. Harmonization with H.241. 1. Introduction A variety of video communication services such as video conferencing and video messaging rely on the capability of video encoders and decoders to respond to control commands. This document outlines a generic set of commands applicable to a variety of video codecs as well as the requirements for their transport. 2. Background RTP [9] is the protocol of choice for the delivery of real time media. RTCP, the companion control protocol, allows some form of monitoring of the media delivery. An enhanced RTCP feedback scheme enabling a generic decoder to provide hints to the corresponding encoder in case of network losses has been described in [7]. Similar solutions were provided for specific coding schemes such ad H.261 [3] H.263 [4] and MPEG-4 [5]. Currently, there is no standard protocol support that allows a given application to exchange control commands with a given codec. 3. Video coding In current coding schemes such as H.261 [2], H.263 [3], MPEG-1, 2,4 [5], H.264 [6] pictures can be coded with various modalities i.e. intra o predicted pictures. Furthermore pictures can be used as references in the decoding process or not. More precisely, intra pictures are pictures that can be decoded without first decoding any other picture. Predicted (or non-intra) pictures may require data from one or more previously decoded pictures in order to be decoded. A reference picture is a picture that is stored in the decoder for use as a reference in the decoding process of some subsequent picture in the video bitstream. Finally a non-reference picture is a picture that is not used as a reference for the decoding process of any other picture in the bitstream. The concepts of intra versus non-intra and reference versus non-reference Basso Expires April 2005 [Page 3] Codec Control Requirements October 2004 are independent. A particular picture can in general be any one of the four types, intra reference, non-intra reference, intra non-reference, non-intra non-reference. Furthermore video pictures are not coded as a whole but are partitioned in small blocks called macrobolocks (MB) and every MB is individually coded. MBs are grouped together in sets of variable size. Such sets are called, in dependence of the coding standard, slices or Group of Blocks (GoBs).Such sets of MB can be scattered in the picture. 4. Use Cases This section describes use cases of codec control commands. 1. A use case includes an RTP video mixer composing multiple encoded video sources into a single encoded video stream. Each time a video source is to be added to the video composition, the RTP mixer needs to request an encoded reference picture from the video source or a specific area of the picture defined by one or more slices. 2. Another use case includes an RTP video mixer that receives multiple encoded RTP video streams from conference participants and dynamically selects one of the streams to be included in its output RTP stream. For every new video stream selected, the mixer will request a intra picture from the remote source in order for the receiving endpoints to be able to decode and display the output stream smoothly when the switch occurs. The video mixer in this scenario will stop the delivery of the current RTP stream and it will wait for the intra picture from the source before it switches to that source. 3. Another use case includes a given application that needs to signal to the remote encoder a request of change in the coding strategy asking to deliver video pictures at a lower frame rate but with better picture quality or vice versa. Such requests may be based on input from the end user. 4. Another use case includes an application that has became aware of packet losses and in order to mitigate their effect requests an intra picture from the remote encoder. This will stop the spatial and temporal propagation of coding errors inherent to commonly used predictive video coding schemes. It is also possible to obtain random access recovery without a fast update. This is sometimes called "gradual decoder refresh". See for example the recovery point SEI message in H.264/AVC [6]. 5. Another use case includes a video mixer that switches its output stream to a new video source. The video mixer will instruct the Basso Expires April 2005 [Page 4] Codec Control Requirements October 2004 receiving endpoints by means of a codec control command to complete the decoding of the current picture and then wait for a new video reference picture. Concurrently, the video mixer requests a reference picture from the new video source and immediately switches to the new source. Once the new source receives the request for the reference picture and acts on it, the receiving endpoints will restart decoding and displaying the new picture. The main benefit of this method as opposed to the video mixer stopping video transmission of the new source until it detects a new reference picture, as in use case 2, is that the video mixer does not have to discover the beginning of a reference picture. This can simplify the video mixer task especially in the case in which the picture has multiple reference pictures. 6. Another use case includes a video mixer that dynamically selects one of the received video streams to be sent out to participants and tries to provide the highest bit rate possible to all participants while minimizing stream transrating. One way of achieving this is for the mixer to setup sessions with endpoints using the maximum bit rate accepted by that endpoint and by the call admission method used by the mixer. By means of commands that allow flow control, the mixer can then reduce the maximum bit rate sent by endpoints to the lowest common denominator of all received streams. As the lowest common denominator changes due to endpoints joining or leaving, the mixer can adjust the limits to which endpoints can send their streams to match the new limit. The mixer then would request a new maximum bit rate, which is equal or less than the maximum bit-rate negotiated at session setup, for a specific media stream, and the remote endpoint can respond with the actual bit-rate that it can support. 5. Codec Commands The ensemble of commands described in this section is divided into two sets. The first set includes commands that are sent to decoders typically to control the presentation of the content. The second set includes commands that are sent to remote encoders. 5.1 Decoder Control Commands 1. VideoFreezePicture It instructs the video decoder to complete the decoding of the current video picture and subsequently display it until a timeout period is elapsed or the receipt of a message that indicates the release of the frozen picture and resume normal decoding and presentation. Note that the freeze picture release command is part of Basso Expires April 2005 [Page 5] Codec Control Requirements October 2004 the H.261, H.262, H.263 and H.264 bitstreams. Coding schemes that support picture freeze release in their bitstreams, MUST use freeze release to signal the remote end to resume decoding. H.264 specifies a timeout period of at least 6 seconds from the receipt of the VideoFreezePicture. See use case 5 for an example of how such command might be used. 5.2 Encoder Control Commands 1. videoFastUpdatePicture A "fast update", also known as an "instantaneous decoder refresh", involves sending an intra picture to a decoder and thereafter refraining from using any picture sent prior to that intra picture as a reference for the decoding process of any subsequent picture sent in the stream. The videoFastUpdatePicture command instructs the video encoder to complete the encoding of the current video picture and to generate a full intra picture at the earliest opportunity. The evaluation of such opportunity includes the current encoder coding strategy and the current available network resources. An H.264 encoder can react to a VideoFastUpdatePicture command with an IDR procedure or a gradual recovery procedure as specified in [10] Intra pictures, independently from the instant in time when they are encoded, are in general several times larger in size than predicted pictures. Thus in scenarios in which the available bandwidth is small the use of a intra picture implies a delay that is significantly longer than the typical picture duration. 2. VideoTemporalSpatialTradeOff(index) It instructs the video encoder to change its trade-off between temporal and spatial resolution. Index assumes values from O to 31 to indicate monotonically a desire for higher frame rate. In general the encoder reaction time may be significantly longer than the typical picture duration. 3. RateRequest(MaxBitrate) It instructs the far-end encoder to change the maximum bit rate of the given media stream being transmitted. MaxBitRate indicates, in units of 100 bit/s, the new requested maximum bit rate for the associated media stream. The new requested bit rate has to be equal to or less than the bit rate negotiated during session setup. 6. General requirements Basso Expires April 2005 [Page 6] Codec Control Requirements October 2004 6.1 Reuse of Existing Protocols The codec control messages should be transported using an already existing transport protocol whenever possible. The transport protocol should allow at a minimum the leveraging of its security elements. 6.2 Maintain Existing Protocol Integrity In meeting the requirement of Section 7, the codec control transport mechanism MUST NOT break existing protocols or cause backward compatibility problems. 6.3 Avoid Duplicating Existing Protocols The codec control mechanism SHOULD NOT duplicate the functionality of existing IETF protocols. The focus of codec control is new functionality not addressed by existing IETF protocols or extending existing IETF protocols within the structures of the requirement in Section 7. Where an existing IETF protocol can be gracefully extended to support codec control requirements, such extensions are acceptable alternatives for meeting the requirements. 6.4 Efficiency The codec control transport mechanism SHOULD employ protocol elements known to result in efficient operation. Techniques to be considered include re-use of transport connections across sessions i.e. codec control messages that controls different media sessions may be aggregated on one codec control transport channel and piggybacking of responses on requests in the reverse direction 7. Codec Control Requirements 7.1 Reliable and Unreliable Delivery. The commands VideoPictureFreeze and VideoTemporalSpatialTradeOff and the commands relative to flow control as RateRequest require a reliable delivery. The command videoFastUpdatePicture implies a specific modification of the media, which is delivered in an unreliable fashion. Given that the delivery of the media is unreliable, the sender cannot rely on the fact that the request has been safely delivered but needs to assure that the requested modification of the data (i.e., insertion of a reference picture) is received before taking any action. Thus the receiver has always to "observe" the incoming data for the requested change independently of the method of delivery of the videoFastUpdatePicture command. VideoFastUpdatePicture can be thus Basso Expires April 2005 [Page 7] Codec Control Requirements October 2004 delivered over an unreliable channel. If the expected change in the media does not happen the command will be retransmitted. 7.2 Transport alternatives Commands such VideoTemporalSpatialTradeOff and RateRequest relative to flow control can be interpreted as changes of a given presentation description and potentially carried via existing protocols such SDP. This is not the case of the VideoFastUpdatePicture and VideoPictureFreeze commands. 7.3 Capability description The capability of codec control for each supported message should be described and negotiated, for example using SDP offer/answer, for both senders and receivers during session setup. The transport protocol used for the delivery of codec control messages should also be specified as of session setup. 7.4 Relation with media session The delivery channel of the codec control messages must be associated with the media session it controls. Using one codec control channel per media session and associating the two channels during session setup could achieve this purpose. Alternatively one media control channel could be used for multiple media sessions. In this case the controlled media session MUST be identified in each codec control message. The transport channel of the codec control messages should follow a similar path to that of the media session it controls. Inter-operability with other standards for codec control delivery might cause a deviation from this requirement. 7.5 Bidirectional transport Messages can be originated from receivers as well as a senders thus the transport mechanism must allow bi-directional exchange of messages. 7.6 Extensibility Codec control message syntax should be extensible to easily support the addition of new control messages. 7.7 Unicast and Multicast Support Basso Expires April 2005 [Page 8] Codec Control Requirements October 2004 The codec control transport MUST work and scale for media sessions that use point-to-point unicast. The codec control transport MUST work and scale for media sessions that use SSM (Source Specific Multicast) and has a small to moderate group size. The codec control transport will not address ASM (Any Source Multicast) media sessions in which media sources are not known until they start transmission. 7.8 Timely delivery For some video services the ability to transmit codec control commands in a timely fashion is essential to the delivery of a high quality user experience. The delay introduced by the transport protocol SHOULD be negligible with respect of the time constants of the delivered media stream. 8. Security Considerations 9. IANA Considerations 10. Acknowledgments The authors would like to acknowledge the comments from around the Community in helping refine this document. Particular recognition goes to Roni Evens. 11. Copyright Notice Copyright (C) The Internet Society (2004). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Basso Expires April 2005 [Page 9] Codec Control Requirements October 2004 12. Informative References 1 S. Bradner, "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997 2 S. Bradner "IETF Rights in Contributions" RFC 3667 February 2004 3 ITU-T Recommendation H.261 (1993), Video codec for audiovisual services at p . 64 kbit/s. 4 ITU-T Recommendation H.263 (1998), Video coding for low bit rate communication. 5 ISO/IEC 14496-2:2001/Amd.1:2002, "Information technology - Coding of audio-visual objects - Part2: Visual", 2001. 6 Joint Video Team of ITU-T and ISO/IEC JTC 1, Draft ITU-T Recommendation and Final Draft International Standard of Joint Video Specification (ITU-T Rec. H.264 | ISO/IEC 14496-10 AVC), Joint Video Team (JVT) of ISO/IEC MPEG and ITU-T VCEG, JVT-G050, March 2003. 7 J. Ott et al. Extended RTP Profile for RTCP-based Feedback (RTP/AVPF), draft-ietf-avt-rtcp-feedback-09.txt, August 2004, IETF Draft. Work in progress. 8 T. Turletti and C. Huitema, "RTP Payload Format for H.261 Video Streams, RFC 2032, October 1996. 9 H. Schulzrinne, S. Casner, R. Frederick, and V. Jacobson, "RTP: A Transport Protocol for Real-time Applications", RFC3550 STD 64 July 2003. 10 ITU-T Recommendation H.241 (07/2003), Extended video procedures and control signals for H.300-series terminals. 11 S. Bradner "Intellectual Property rights in IETF Technology" RFC3668, February 2004 13. IPR Notices The IETF takes no position regarding the validity or scope of any Basso Expires April 2005 [Page 10] Codec Control Requirements October 2004 Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Author's Addresses Andrea Basso NMS Communications 200 Shultz Drive Red Bank, NJ 07701 USA Phone: (732) 936-2118 Email: andrea_basso@nmss.com Orit Levin Microsoft Corporation One Microsoft Way Redmond, WA 98052 USA EMail: oritl@microsoft.com Nermeen Ismail Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706, USA Phone: +1 408 853 8714 Email: nismail@cisco.com Basso Expires April 2005 [Page 11]