rfc5171









Network Working Group                                       M. Foschiano
Request for Comments: 5171                                 Cisco Systems
Category: Informational                                       April 2008


      Cisco Systems UniDirectional Link Detection (UDLD) Protocol

Status of This Memo

   This memo provides information for the Internet community.  It does
   not specify an Internet standard of any kind.  Distribution of this
   memo is unlimited.

IESG Note

   This RFC is not a candidate for any level of Internet Standard.  The
   IETF disclaims any knowledge of the fitness of this RFC for any
   purpose and in particular notes that the decision to publish is not
   based on IETF review for such things as security, congestion control,
   or inappropriate interaction with deployed protocols.  The RFC Editor
   has chosen to publish this document at its discretion.  Readers of
   this document should exercise caution in evaluating its value for
   implementation and deployment.  See RFC 3932 for more information.

Abstract

   This document describes a Cisco Systems protocol that can be used to
   detect and disable unidirectional Ethernet fiber or copper links
   caused, for instance, by mis-wiring of fiber strands, interface
   malfunctions, media converters' faults, etc.  It operates at Layer 2
   in conjunction with IEEE 802.3's existing Layer 1 fault detection
   mechanisms.

   This document explains the protocol objectives and applications,
   illustrates the specific premises the protocol was based upon, and
   describes the protocol architecture and related deployment issues to
   serve as a possible base for future standardization.














Foschiano                    Informational                      [Page 1]

RFC 5171                          UDLD                        April 2008


Table of Contents

   1. Introduction ....................................................2
   2. Protocol Objectives and Applications ............................3
   3. Protocol Design Premises ........................................4
   4. Protocol Background .............................................4
   5. Protocol Architecture ...........................................5
      5.1. The Basics .................................................5
      5.2. Neighbor Database Maintenance ..............................5
      5.3. Event-driven Detection and Echoing .........................6
      5.4. Event-based versus Event-less Detection ....................6
   6. Packet Format ...................................................7
      6.1. TLV Description ............................................9
   7. Protocol Logic .................................................10
      7.1. Protocol Timers ...........................................10
   8. Comparison with Bidirectional Forwarding Detection .............11
   9. Security Considerations ........................................11
   10. Deployment Considerations .....................................11
   11. Normative References ..........................................12
   12. Informative Reference .........................................12

1.  Introduction

   Today's Ethernet-based switched networks often rely on the Spanning
   Tree Protocol (STP) defined in the IEEE 802.1D standard [1] to create
   a loop-free topology that is used to forward the traffic from a
   source to a destination based on the Layer 2 packet information
   learned by the switches and on the knowledge of the status of the
   physical links along the path.

   Issues arise when, due to mis-wirings or to hardware faults, the
   communication path behaves abnormally and generates forwarding
   anomalies.  The simplest example of such anomalies is the case of a
   bidirectional link that stops passing traffic in one direction and
   therefore breaks one of the most basic assumptions that high-level
   protocols typically depend upon: reliable two-way communication
   between peers.

   The purpose of the UDLD protocol is to detect the presence of
   anomalous conditions in the Layer 2 communication channel, while
   relying on the mechanisms defined by the IEEE in the 802.3 standard
   [2] to properly handle conditions inherent to the physical layer.









Foschiano                    Informational                      [Page 2]

RFC 5171                          UDLD                        April 2008


2.  Protocol Objectives and Applications

   The UniDirectional Link Detection protocol (often referred to in
   short as "UDLD") is a lightweight protocol that can be used to detect
   and disable one-way connections before they create dangerous
   situations such as Spanning Tree loops or other protocol
   malfunctions.

   The protocol's main goal is to advertise the identities of all the
   capable devices attached to the same LAN segment and to collect the
   information received on the ports of each device to determine if the
   Layer 2 communication is happening in the appropriate fashion.

   In a network that has an extensive fiber cabling plant, problems may
   arise when incorrect patching causes a switch port to have its RX
   fiber strand connected to one neighbor port and its TX fiber strand
   connected to another.  In these cases, a port may be deemed active if
   it is receiving an optical signal on its RX strand.  However, the
   problem is that this link does not provide a valid communication path
   at Layer 2 (and above).

   If this scenario of wrongly connected fiber strands is applied to
   multiple ports to create a fiber loop, each device in the loop could
   directly send packets to a neighbor but would not be able to receive
   from that neighbor.

   Albeit the above scenario is rather extreme, it exemplifies how the
   lack of mutual identification of the neighbors can bring protocols to
   the wrong assumption that during a transmission the sender and the
   receiver are always properly matched.  Another equally dangerous
   incorrect assumption is that the lack of reception of protocol
   messages on a port unmistakably indicates the absence of transmitting
   protocol entities at the other end of the link.

   The UDLD protocol was implemented to help correct certain assumptions
   made by other protocols, and in particular to help the Spanning Tree
   Protocol to function properly so as to avoid the creation of
   dangerous Layer 2 loops.  It has been available on most Cisco Systems
   switches for several years and is now part of numerous network design
   best practices.











Foschiano                    Informational                      [Page 3]

RFC 5171                          UDLD                        April 2008


3.  Protocol Design Premises

   The current implementation of UDLD is based on the following
   considerations/presuppositions:

      o  The protocol would have to be run in the control plane of a
         network device to be flexible enough to support upgrades and
         bug fixes.  The control plane speed would ultimately be the
         limiting factor to the capability of fast fault detection of
         the protocol (CPU speed, task switching speed, event processing
         speed, etc.).  The transmission medium's propagation delay at
         10 Mbps speed (or higher) would instead be considered a
         negligible factor.

      o  Network events typically do not happen with optimal timing, but
         rather at the speed determined by the software/firmware
         infrastructure that controls them.  (For psychological and
         practical reasons, developers tend to choose round timer values
         rather than determine the optimal value for the specific
         software architecture in use.  Also, software bugs, coding
         oversights, slow process switching, implementation overhead can
         all affect the control plane responsiveness and event timings.)
         Hence it was deemed necessary to adopt a conservative protocol
         design to minimize false positives during the detection
         process.

      o  If a fault were discovered, it was assumed that the user would
         want to keep the faulty port down for a predetermined amount of
         time to avoid unnecessary port state flapping.  For that
         reason, a time-based fault recovery mechanism was provided
         (although alternative recovery mechanisms are not implicitly
         precluded by the protocol itself).

4.  Protocol Background

   UDLD is meant to be a Layer 2 detection protocol that works on top of
   the existing Layer 1 detection mechanisms defined by the IEEE
   standards.  For example, the Far End Fault Indication (FEFI) function
   for 100BaseFX interfaces and the Auto-Negotiation function for
   100BaseTX/1000BaseX interfaces represent standard physical-layer
   mechanisms to determine if the transmission media is bidirectional.
   (Please see sections 24.3.2.1 and 28.2.3.5 of [2] for more details.)
   The typical case of a Layer 1 "fault" indication is the "loss of
   light" indication.

   UDLD differs from the above-mentioned mechanisms insofar as it
   performs mutual neighbor identification; in addition, it performs
   neighbor acknowledgement on top of the Logical Link Control (LLC)



Foschiano                    Informational                      [Page 4]

RFC 5171                          UDLD                        April 2008


   layer and thus is able to discover logical one-way miscommunication
   between neighbors even when either one of the said PHY layer
   mechanisms has deemed the transmission medium bidirectional.

5.  Protocol Architecture

5.1.  The Basics

   UDLD uses two basic mechanisms:

      a. It advertises a port's identity and learns about its neighbors
         on a specific LAN segment; it keeps the acquired information on
         the neighbors in a cache table.

      b. It sends a train of echo messages in certain circumstances that
         require fast notifications or fast resynchronization of the
         cached information.

   Because of the above, the algorithm run by UDLD requires that all the
   devices connected to the same LAN segment be running the protocol in
   order for a potential misconfiguration to be detected and for a
   prompt corrective action to be taken.

5.2.  Neighbor Database Maintenance

   UDLD sends periodical "hello" packets (also called "advertisements"
   or "probes") on every active interface to keep each device informed
   about its neighbors.  When a hello message is received, it is cached
   and kept in memory at most for a defined time interval, called
   "holdtime" or "time-to-live", after which the cache entry is
   considered stale and is aged out.

   If a new hello message is received when a correspondent old cache
   entry has not been aged out yet, then the old entry is dropped and is
   replaced by the new one with a reset time-to-live timer.  Whenever an
   interface gets disabled and UDLD is running, or whenever UDLD is
   disabled on an interface, or whenever the device is reset, all
   existing cache entries for the interfaces affected by the
   configuration change are cleared, and UDLD sends at least one message
   to inform the neighbors to flush the part of their caches also
   affected by the status change.  This mechanism is meant to keep the
   caches coherent on all the connected devices.









Foschiano                    Informational                      [Page 5]

RFC 5171                          UDLD                        April 2008


5.3.  Event-driven Detection and Echoing

   The echoing mechanism is the base of UDLD's detection algorithm:
   whenever a UDLD device learns about a new neighbor or receives a
   resynchronization request from an out-of-synch neighbor, it
   (re)starts the detection process on its side of the connection and
   sends N echo messages in reply.  (This mechanism implicitly assumes
   that N packets are sufficient to get through a link and reach the
   other end, even though some of them might get dropped during the
   transmission.)

   Since this behavior must be the same on all the neighbors, the sender
   of the echoes expects to receive (after some time) an echo in reply.
   If the detection process ends without the proper echo information
   being received, and under specific conditions, the link is considered
   to be unidirectional.

5.4.  Event-based versus Event-less Detection

   UDLD can function in two modes: normal mode and aggressive mode.

   In normal mode, a protocol determination at the end of the detection
   process is always based on information received in UDLD messages:
   whether it's the information about the exchange of proper neighbor
   identifications or the information about the absence of such proper
   identifications.  Hence, albeit bound by a timer, normal mode
   determinations are always based on gleaned information, and as such
   are "event-based".  If no such information can be obtained (e.g.,
   because of a bidirectional loss of connectivity), UDLD follows a
   conservative approach based on the considerations in Section 3 and
   deems a port to be in "undetermined" state.  In other words, normal
   mode will shut down a port only if it can explicitly determine that
   the associated link is faulty for an extended period of time.

   In contrast, in aggressive mode, UDLD will also shut down a port if
   it loses bidirectional connectivity with the neighbor for the same
   extended period of time mentioned above and subsequently fails
   repeated last-resort attempts to re-establish communication with the
   other end of the link.  This mode of operation assumes that loss of
   communication with the neighbor is a meaningful network event in
   itself and is a symptom of a serious connectivity problem.  Because
   this type of detection can be event-less, and lack of information
   cannot always be associated to an actual malfunction of the link,
   this mode is optional and is recommended only in certain scenarios
   (typically only on point-to-point links where no communication
   failure between two neighbors is admissible).





Foschiano                    Informational                      [Page 6]

RFC 5171                          UDLD                        April 2008


6.  Packet Format

   The UDLD protocol runs on top of the LLC sub-layer of the data link
   layer of the OSI model.  It uses a specially assigned multicast
   destination MAC address and encapsulates its messages using the
   standard Subnetwork Access Protocol (SNAP) format as described in the
   following:

         Destination MAC address            01-00-0C-CC-CC-CC

         UDLD SNAP format:
           LLC value                        0xAAAA03
           Org Id                           0x00000C
           HDLC protocol type               0x0111

   UDLD's Protocol Data Unit (PDU) format is as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   | Ver | Opcode  |     Flags     |           Checksum            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |               List of TLVs (variable length list)             |
   |                              ...                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The TLV format is the basic one described below:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             TYPE              |            LENGTH             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                             VALUE                             |
   |                              ...                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Type (16 bits): If an implementation does not understand a Type
         value, it should skip over it using the length field.

   Length (16 bits): Length in bytes of the Type, Length, and Value
         fields.  In order for this field value to be valid, it should
         be greater than or equal to the minimum allowed length, 4
         bytes.  If the value is less than the minimum, the whole packet
         is to be considered corrupted and therefore it must be
         discarded right away during the parsing process.  TLVs should
         not be split across packet boundaries.




Foschiano                    Informational                      [Page 7]

RFC 5171                          UDLD                        April 2008


   Value (variable length): Object contained in the TLV.

   The protocol header fields are defined as follows:

   Ver (3 bits):
         0x01: UDLD PDU version number

   Opcode (5 bits):
         0x00: Reserved
         0x01: Probe message
         0x02: Echo message
         0x03: Flush message
         0x04-0x1F: Reserved for future use

   Flags (8 bits):
         bit 0: Recommended timeout flag (RT)
         bit 1: ReSynch flag (RSY)
         bit 2-7: Reserved for future use

   PDU Checksum (16 bits):
         IP-like checksum.  Take the one's complement of the one's
         complement sum (with the modification that the odd byte at the
         end of an odd length message is used as the low 8 bits of an
         extra word, rather than as the high 8 bits.)  NB: All UDLD
         implementations must comply with this specification.

   The list of currently defined TLVs comprises:

      Name                   Type      Value format

      Device-ID TLV          0x0001    ASCII character string
      Port-ID TLV            0x0002    ASCII character string
      Echo TLV               0x0003    List of ID pairs
      Message Interval TLV   0x0004    8-bit unsigned integer
      Timeout Interval TLV   0x0005    8-bit unsigned integer
      Device Name TLV        0x0006    ASCII character string
      Sequence Number TLV    0x0007    32-bit unsigned integer
      Reserved TLVs          > 0x0007  Format unknown.
                                       To be skipped by parsing routine.












Foschiano                    Informational                      [Page 8]

RFC 5171                          UDLD                        April 2008


6.1.  TLV Description

   Device-ID TLV:

      This TLV uniquely identifies the device that is sending the UDLD
      packet.  The TLV length field determines the length of the carried
      identifier and must be greater than zero.  In version 1 of the
      protocol, the lack of this ID is considered a symptom of packet
      corruption that implies that the message is invalid and must be
      discarded.

   Port-ID TLV:

      This TLV uniquely identifies the physical port the UDLD packet is
      sent on.  The TLV length field determines the length of the
      carried identifier and must be greater than zero.  In version 1 of
      the protocol, the lack of this ID is considered a symptom of
      packet corruption that implies that the message is invalid and
      must be discarded.

   Echo TLV:

      This TLV contains the list of valid DeviceID/PortID pairs received
      by a port from all its neighbors.  If either one of the
      identifiers in a pair is corrupted, the message will be ignored.
      This list includes only DeviceIDs and PortIDs extracted from UDLD
      messages received and cached on the same interface on which this
      TLV is sent.  If no UDLD messages are received, then this TLV is
      sent containing zero pairs.  Despite its name, this TLV must be
      present in both probe and echo messages, whereas in flush messages
      it's not required.

   Message Interval TLV:

      This required TLV contains the 8-bit time interval value used by a
      neighbor to send UDLD probes after the linkup or detection phases.
      Its time unit is 1 second.  The holdtime of a cache item for a
      received message is calculated as (advertised-message-interval x
      R), where R is a constant called "TTL to message interval ratio".

   Timeout Interval TLV:

      This optional TLV contains the 8-bit timeout interval value (T)
      used by UDLD to decide the basic length of the detection phase.
      Its time unit is 1 second.  If it's not present in an
      advertisement, T is assumed to be a hard-coded constant.





Foschiano                    Informational                      [Page 9]

RFC 5171                          UDLD                        April 2008


   Device Name TLV:

      This required TLV is meant to be used by the CLI or SNMP and
      typically contains the user-readable device name string.

   Sequence Number TLV:

      The purpose of this optional TLV is to inform the neighbors of the
      sequence number of the current message being transmitted.  A
      counter from 1 to 2^32-1 is supposed to keep track of the sequence
      number; it is reset whenever a transition of phase occurs so that
      it will restart counting from one, for instance, whenever an echo
      message sequence is initiated, or whenever a linkup message train
      is triggered.

      No wraparound of the counter is supposed to happen.

      The zero value is reserved and can be used as a representation of
      a missing or invalid sequence number by the user interface.
      Therefore, the TLV should never contain zero.  (NB: The use of
      this TLV is currently limited only to informational purposes.)

7.  Protocol Logic

   UDLD's protocol logic relies on specific internal timers and is
   sensitive to certain network events.

   The type of messages that UDLD transmits and the timing intervals
   that it uses are dependent upon the internal state of the protocol,
   which changes based on network events such as:

      o  Link up
      o  Link down
      o  Protocol enabled
      o  Protocol disabled
      o  New neighbor discovery
      o  Neighbor state change
      o  Neighbor resynchronization requests

7.1.  Protocol Timers

   UDLD timer values could vary within certain "safety" ranges based on
   the considerations in Section 3.  However, in practice, in the
   current implementation, timers use only certain values verified
   during testing.  Their time unit is one second.

   During the detection phase, messages are exchanged at the maximum
   possible rate of one per second.  After that, if the protocol reaches



Foschiano                    Informational                     [Page 10]

RFC 5171                          UDLD                        April 2008


   a stable state and can make a certain determination on the
   "bidirectionality" of the link, the message interval is increased to
   a configurable value based on a curve known as M1(t), a time-based
   function.

   In case the link is deemed anything other than bidirectional at the
   end of the detection, this curve is a flat line with a fixed value of
   Mfast (7 seconds in the current implementation).

   In case the link is instead deemed bidirectional, the curve will use
   Mfast for the first 4 subsequent message transmissions and then will
   transition to an Mslow value for all other steady-state
   transmissions.  Mslow can be either a fixed value (60 seconds in some
   obsolete implementations) or a user-configurable value (between Mfast
   and 90 seconds with a default of 15 seconds in the current
   implementations).

8.  Comparison with Bidirectional Forwarding Detection

   Similarly to UDLD, the Bidirectional Forwarding Detection (BFD) [3]
   protocol is intended to detect faults in the path between two network
   nodes.  However, BFD is supposed to operate independently of media,
   data protocols, and routing protocols.  There is no address discovery
   mechanism in BFD, which is left to the application to determine.

   On the other hand, UDLD works exclusively on top of a L2 transport
   supporting the SNAP encapsulation and operates independently of the
   other bridge protocols (UDLD's main "applications"), with which it
   has limited interaction.  It also performs full neighbor discovery on
   point-to-point and point-to-multipoint media.

9.  Security Considerations

   In a heterogeneous Layer 2 network that is built with different
   models of network devices or with devices running different software
   images, the UDLD protocol should be supported and configured on all
   ports interconnecting said devices in order to achieve a complete
   coverage of its detection process.  Note that UDLD is not supposed to
   be used on ports connected to untrusted devices or incapable devices;
   hence, it should be disabled on such ports.

10.  Deployment Considerations

   Cisco Systems has supported the UDLD protocol in its Catalyst family
   of switches since 1999.






Foschiano                    Informational                     [Page 11]

RFC 5171                          UDLD                        April 2008


11.  Normative References

   [1]  IEEE 802.1D-2004 Standard -- Media access control (MAC) Bridges

   [2]  IEEE 802.3-2002 IEEE Standard -- Local and metropolitan area
        networks Specific requirements--Part 3: Carrier Sense Multiple
        Access with Collision Detection (CSMA/CD) Access Method and
        Physical Layer Specifications

12.  Informative Reference

   [3]  Katz, D., and D. Ward, "Bidirectional Forwarding Detection",
        Work in Progress, March 2008.

Author's Address

   Marco Foschiano
   Cisco Systems, Inc.
   Via Torri Bianche 7,
   20059 Vimercate (Mi)
   Italy

   EMail: foschia@cisco.com




























Foschiano                    Informational                     [Page 12]

RFC 5171                          UDLD                        April 2008


Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78 and at http://www.rfc-editor.org/copyright.html,
   and except as set forth therein, the authors retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.












Foschiano                    Informational                     [Page 13]



ERRATA