rfc4191









Network Working Group                                          R. Draves
Request for Comments: 4191                                     D. Thaler
Category: Standards Track                                      Microsoft
                                                           November 2005


          Default Router Preferences and More-Specific Routes

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (2005).

Abstract

   This document describes an optional extension to Router Advertisement
   messages for communicating default router preferences and more-
   specific routes from routers to hosts.  This improves the ability of
   hosts to pick an appropriate router, especially when the host is
   multi-homed and the routers are on different links.  The preference
   values and specific routes advertised to hosts require administrative
   configuration; they are not automatically derived from routing
   tables.

1.  Introduction

   Neighbor Discovery [RFC2461] specifies a conceptual model for hosts
   that includes a Default Router List and a Prefix List.  Hosts send
   Router Solicitation messages and receive Router Advertisement
   messages from routers.  Hosts populate their Default Router List and
   Prefix List based on information in the Router Advertisement
   messages.  A conceptual sending algorithm uses the Prefix List to
   determine if a destination address is on-link and uses the Default
   Router List to select a router for off-link destinations.

   In some network topologies where the host has multiple routers on its
   Default Router List, the choice of router for an off-link destination
   is important.  In some situations, one router may provide much better
   performance than another for a destination.  In other situations,
   choosing the wrong router may result in a failure to communicate.
   (Section 5 gives specific examples of these scenarios.)



Draves & Thaler             Standards Track                     [Page 1]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   This document describes an optional extension to Neighbor Discovery
   Router Advertisement messages for communicating default router
   preferences and more-specific routes from routers to hosts.  This
   improves the ability of hosts to pick an appropriate router for an
   off-link destination.

   Note that since these procedures are applicable to hosts only, the
   forwarding algorithm used by the routers (including hosts with
   enabled IP forwarding) is not affected.

   Neighbor Discovery provides a Redirect message that routers can use
   to correct a host's choice of router.  A router can send a Redirect
   message to a host, telling it to use a different router for a
   specific destination.  However, the Redirect functionality is limited
   to a single link.  A router on one link cannot redirect a host to a
   router on another link.  Hence, Redirect messages do not help multi-
   homed (through multiple interfaces) hosts select an appropriate
   router.

   Multi-homed hosts are an increasingly important scenario, especially
   with IPv6.  In addition to a wired network connection, like Ethernet,
   hosts may have one or more wireless connections, like 802.11 or
   Bluetooth.  In addition to physical network connections, hosts may
   have virtual or tunnel network connections.  For example, in addition
   to a direct connection to the public Internet, a host may have a
   tunnel into a private corporate network.  Some IPv6 transition
   scenarios can add additional tunnels.  For example, hosts may have
   6to4 [RFC3056] or configured tunnel [RFC2893] network connections.

   This document requires that the preference values and specific routes
   advertised to hosts require explicit administrative configuration.
   They are not automatically derived from routing tables.  In
   particular, the preference values are not routing metrics and it is
   not recommended that routers "dump out" their entire routing tables
   to hosts.

   We use Router Advertisement messages, instead of some other protocol
   like RIP [RFC2080], because Router Advertisements are an existing
   standard, stable protocol for router-to-host communication.
   Piggybacking this information on existing message traffic from
   routers to hosts reduces network overhead.  Neighbor Discovery shares
   with Multicast Listener Discovery the property that they both define
   host-to-router interactions, while shielding the host from having to
   participate in more general router-to-router interactions.  In
   addition, RIP is unsuitable because it does not carry route lifetimes
   so it requires frequent message traffic with greater processing
   overheads.




Draves & Thaler             Standards Track                     [Page 2]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   The mechanisms specified here are backwards-compatible, so that hosts
   that do not implement them continue to function as well as they did
   previously.

1.1.  Conventions Used in This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2.  Message Formats

2.1.  Preference Values

   Default router preferences and preferences for more-specific routes
   are encoded the same way.

   Preference values are encoded as a two-bit signed integer, as
   follows:

      01      High
      00      Medium (default)
      11      Low
      10      Reserved - MUST NOT be sent

   Note that implementations can treat the value as a two-bit signed
   integer.

   Having just three values reinforces that they are not metrics and
   more values do not appear to be necessary for reasonable scenarios.





















Draves & Thaler             Standards Track                     [Page 3]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


2.2.  Changes to Router Advertisement Message Format

   The changes from Neighbor Discovery [RFC2461] Section 4.2 and
   [RFC3775] Section 7.1 are as follows:

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |     Code      |          Checksum             |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      | Cur Hop Limit |M|O|H|Prf|Resvd|       Router Lifetime         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                         Reachable Time                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                          Retrans Timer                        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |   Options ...
      +-+-+-+-+-+-+-+-+-+-+-+-

   Fields:

   Prf (Default Router Preference)
            2-bit signed integer.  Indicates whether to prefer this
            router over other default routers.  If the Router Lifetime
            is zero, the preference value MUST be set to (00) by the
            sender and MUST be ignored by the receiver.  If the Reserved
            (10) value is received, the receiver MUST treat the value as
            if it were (00).

   Resvd (Reserved)
            A 3-bit unused field.  It MUST be initialized to zero by the
            sender and MUST be ignored by the receiver.

   Possible Options:

   Route Information
            These options specify prefixes that are reachable via the
            router.

   Discussion:

   Note that in addition to the preference value in the message header,
   a Router Advertisement can also contain a Route Information Option
   for ::/0, with a preference value and lifetime.  Encoding a
   preference value in the Router Advertisement header has some
   advantages:





Draves & Thaler             Standards Track                     [Page 4]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   1. It allows for a distinction between the "best router for the
      default route" and the "router least likely to redirect common
      traffic", as described below in Section 5.1.

   2. When the best router for the default route is also the router
      least likely to redirect common traffic (which will be a common
      case), encoding the preference value in the message header is more
      efficient than sending a separate option.

2.3.  Route Information Option

      0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |     Type      |    Length     | Prefix Length |Resvd|Prf|Resvd|
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                        Route Lifetime                         |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                   Prefix (Variable Length)                    |
      .                                                               .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Fields:

   Type        24

   Length      8-bit unsigned integer.  The length of the option
               (including the Type and Length fields) in units of 8
               octets.  The Length field is 1, 2, or 3 depending on the
               Prefix Length.  If Prefix Length is greater than 64, then
               Length must be 3.  If Prefix Length is greater than 0,
               then Length must be 2 or 3.  If Prefix Length is zero,
               then Length must be 1, 2, or 3.

   Prefix Length
               8-bit unsigned integer.  The number of leading bits in
               the Prefix that are valid.  The value ranges from 0 to
               128.  The Prefix field is 0, 8, or 16 octets depending on
               Length.

   Prf (Route Preference)
               2-bit signed integer.  The Route Preference indicates
               whether to prefer the router associated with this prefix
               over others, when multiple identical prefixes (for
               different routers) have been received.  If the Reserved
               (10) value is received, the Route Information Option MUST
               be ignored.



Draves & Thaler             Standards Track                     [Page 5]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   Resvd (Reserved)
               Two 3-bit unused fields.  They MUST be initialized to
               zero by the sender and MUST be ignored by the receiver.

   Route Lifetime
               32-bit unsigned integer.  The length of time in seconds
               (relative to the time the packet is sent) that the prefix
               is valid for route determination.  A value of all one
               bits (0xffffffff) represents infinity.

   Prefix      Variable-length field containing an IP address or a
               prefix of an IP address.  The Prefix Length field
               contains the number of valid leading bits in the prefix.
               The bits in the prefix after the prefix length (if any)
               are reserved and MUST be initialized to zero by the
               sender and ignored by the receiver.

   Routers MUST NOT include two Route Information Options with the same
   Prefix and Prefix Length in the same Router Advertisement.

   Discussion:

   There are several reasons for using a new Route Information Option
   instead of using flag bits to overload the existing Prefix
   Information Option:

   1. Prefixes will typically only show up in one option, not both, so a
      new option does not introduce duplication.

   2. The Route Information Option is typically 16 octets while the
      Prefix Information Option is 32 octets.

   3. Using a new option may improve backwards-compatibility with some
      host implementations.

3.  Conceptual Model of a Host

   There are three possible conceptual models for a host implementation
   of default router preferences and more-specific routes, corresponding
   to different levels of support.  We refer to these as type A, type B,
   and type C.

3.1.  Conceptual Data Structures for Hosts

   Type A hosts ignore default router preferences and more-specific
   routes.  They use the conceptual data structures described in
   Neighbor Discovery [RFC2461].




Draves & Thaler             Standards Track                     [Page 6]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   Type B hosts use a Default Router List augmented with preference
   values, but ignore all Route Information Options.  They use the
   Default Router Preference value in the Router Advertisement header.
   They ignore Route Information Options.

   Type C hosts use a Routing Table instead of a Default Router List.
   (The Routing Table may also subsume the Prefix List, but that is
   beyond the scope of this document.)  Entries in the Routing Table
   have a prefix, prefix length, preference value, lifetime, and next-
   hop router.  Type C hosts use both the Default Router Preference
   value in the Router Advertisement header and Route Information
   Options.

   When a type C host receives a Router Advertisement, it modifies its
   Routing Table as follows.  When processing a Router Advertisement, a
   type C host first updates a ::/0 route based on the Router Lifetime
   and Default Router Preference in the Router Advertisement message
   header.  Then as the host processes Route Information Options in the
   Router Advertisement message body, it updates its routing table for
   each such option.  The Router Preference and Lifetime values in a
   ::/0 Route Information Option override the preference and lifetime
   values in the Router Advertisement header.  Updating each route is
   done as follows.  A route is located in the Routing Table based on
   the prefix, prefix length, and next-hop router.  If the received
   route's lifetime is zero, the route is removed from the Routing Table
   if present.  If a route's lifetime is non-zero, the route is added to
   the Routing Table if not present and the route's lifetime and
   preference is updated if the route is already present.

   For example, suppose hosts receive a Router Advertisement from router
   X with a Router Lifetime of 100 seconds and a Default Router
   Preference of Medium.  The body of the Router Advertisement contains
   a Route Information Option for ::/0 with a Route Lifetime of 200
   seconds and a Route Preference of Low.  After processing the Router
   Advertisement, a type A host will have an entry for router X in its
   Default Router List with a lifetime of 100 seconds.  If a type B host
   receives the same Router Advertisement, it will have an entry for
   router X in its Default Router List with a Medium preference and a
   lifetime of 100 seconds.  A type C host will have an entry in its
   Routing Table for ::/0 -> router X, with a Low preference and a
   lifetime of 200 seconds.  During processing of the Router
   Advertisement, a type C host MAY have a transient state, in which it
   has an entry in its Routing Table for ::/0 -> router X with a Medium
   preference and a lifetime of 100 seconds.







Draves & Thaler             Standards Track                     [Page 7]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


3.2.  Conceptual Sending Algorithm for Hosts

   Type A hosts use the conceptual sending algorithm described in
   Neighbor Discovery [RFC2461].

   When a type B host does next-hop determination and consults its
   Default Router List, it primarily prefers reachable routers over
   non-reachable routers and secondarily uses the router preference
   values.  If the host has no information about the router's
   reachability, then the host assumes the router is reachable.

   When a type C host does next-hop determination and consults its
   Routing Table for an off-link destination, it searches its routing
   table to find the route with the longest prefix that matches the
   destination, using route preference values as a tie-breaker if
   multiple matching routes have the same prefix length.  If the best
   route points to a non-reachable router, this router is remembered for
   the algorithm described in Section 3.5 below, and the next best route
   is consulted.  This check is repeated until a matching route is found
   that points to a reachable router, or no matching routes remain.
   Again, if the host has no information about the router's
   reachability, then the host assumes the router is reachable.

   If there are no routes matching the destination (i.e., no default
   routes and no more-specific routes), then a type C host SHOULD
   discard the packet and report a Destination Unreachable/No Route To
   Destination error to the upper layer.

3.3.  Destination Cache Management

   When a type C host processes a Router Advertisement and updates its
   conceptual Routing Table, it MUST invalidate or remove Destination
   Cache Entries and redo next-hop determination for destinations
   affected by the Routing Table changes.

3.4.  Client Configurability

   Type B and C hosts MAY be configurable with preference values that
   override the values in Router Advertisements received.  This is
   especially useful for dealing with routers that may not support
   preferences.

3.5.  Router Reachability Probing

   When a host avoids using any non-reachable router X and instead sends
   a data packet to another router Y, and the host would have used
   router X if router X were reachable, then the host SHOULD probe each
   such router X's reachability by sending a single Neighbor



Draves & Thaler             Standards Track                     [Page 8]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   Solicitation to that router's address.  A host MUST NOT probe a
   router's reachability in the absence of useful traffic that the host
   would have sent to the router if it were reachable.  In any case,
   these probes MUST be rate-limited to no more than one per minute per
   router.

   This requirement allows the host to discover when router X becomes
   reachable and to start using router X at that time.  Otherwise, the
   host might not notice router X's reachability and continue to use the
   less-desirable router Y until the next Router Advertisement is sent
   by X.  Note that the router may have been unreachable for reasons
   other than being down (e.g., a switch in the middle being down), so
   it may be up to 30 minutes (the maximum advertisement period) before
   the next Router Advertisement would be sent.

   For a type A host (following the algorithm in [RFC2461]), no probing
   is needed since all routers are equally preferable.  A type B or C
   host, on the other hand, explicitly probes unreachable, preferable
   routers to notice when they become reachable again.

3.6.  Example

   Suppose a type C host has four entries in its Routing Table:

      ::/0 -> router W with a Medium preference
      2002::/16 -> router X with a Medium preference
      2001:db8::/32-> router Y with a High preference
      2001:db8::/32-> router Z with a Low preference

   and the host is sending to 2001:db8::1, an off-link destination.  If
   all routers are reachable, then the host will choose router Y.  If
   router Y is not reachable, then router Z will be chosen and the
   reachability of router Y will be probed.  If routers Y and Z are not
   reachable, then router W will be chosen and the reachability of
   routers Y and Z will be probed.  If routers W, Y, and Z are all not
   reachable, then the host should use Y while probing the reachability
   of W and Z.  Router X will never be chosen because its prefix does
   not match the destination.

4.  Router Configuration

   Routers SHOULD NOT advertise preferences or routes by default.  In
   particular, they SHOULD NOT "dump out" their entire routing table to
   hosts.

   Routers MAY have a configuration mode in which an announcement of a
   specific prefix is dependent on a specific condition, such as
   operational status of a link or presence of the same or another



Draves & Thaler             Standards Track                     [Page 9]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   prefix in the routing table installed by another source, such as a
   dynamic routing protocol.  If done, router implementations SHOULD
   make sure that announcement of prefixes to hosts is decoupled from
   the routing table dynamics to prevent an excessive load on hosts
   during periods of routing instability.  In particular, unstable
   routes SHOULD NOT be announced to hosts until their stability has
   improved.

   Routers SHOULD NOT send more than 17 Route Information Options in
   Router Advertisements per link.  This arbitrary bound is meant to
   reinforce that relatively few and carefully selected routes should be
   advertised to hosts.

   The preference values (both Default Router Preferences and Route
   Preferences) SHOULD NOT be routing metrics or automatically derived
   from metrics: the preference values SHOULD be configured.

   The information contained in Router Advertisements may change through
   the actions of system management.  For instance, the lifetime or
   preference of advertised routes may change, or new routes could be
   added.  In such cases, the router MAY transmit up to
   MAX_INITIAL_RTR_ADVERTISEMENTS unsolicited advertisements, using the
   same rules as in [RFC2461].  When ceasing to be an advertising
   interface and sending Router Advertisements with a Router Lifetime of
   zero, the Router Advertisement SHOULD also set the Route Lifetime to
   zero in all Route Information Options.

4.1.  Guidance to Administrators

   The High and Low (non-default) preference values should only be used
   when someone with knowledge of both routers and the network topology
   configures them explicitly.  For example, it could be a common
   network administrator, or it could be a customer request to different
   administrators managing the routers.

   As one exception to this general rule, the administrator of a router
   that does not have a connection to the Internet, or is connected
   through a firewall that blocks general traffic, should configure the
   router to advertise a Low Default Router Preference.

   In addition, the administrator of a router should configure the
   router to advertise a specific route for the site prefix of the
   network(s) to which the router belongs.  The administrator may also
   configure the router to advertise specific routes for directly
   connected subnets and any shorter prefixes for networks to which the
   router belongs.





Draves & Thaler             Standards Track                    [Page 10]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   For example, if a home user sets up a tunnel into a firewalled
   corporate network, the access router on the corporate network end of
   the tunnel should advertise itself as a default router, but with a
   Low preference.  Furthermore, the corporate router should advertise a
   specific route for the corporate site prefix.  The net result is that
   destinations in the corporate network will be reached via the tunnel,
   and general Internet destinations will be reached via the home ISP.
   Without these mechanisms, the home machine might choose to send
   Internet traffic into the corporate network or corporate traffic into
   the Internet, leading to communication failure because of the
   firewall.

   It is worth noting that the network administrator setting up
   preferences and/or more specific routes in Routing Advertisements
   typically does not know which kind of nodes (Type A, B, and/or C)
   will be connected to its links.  This requires that the administrator
   configure the settings that will work in an optimal fashion
   regardless of which kinds of nodes will be attached.  Two examples of
   how to do so follow.

5.  Examples

5.1.  Best Router for ::/0 vs Router Least Likely to Redirect

   The best router for the default route is the router with the best
   route toward the wider Internet.  The router least likely to redirect
   traffic depends on the actual traffic usage.  The two concepts can be
   different when the majority of communication actually needs to go
   through some other router.

   For example, consider a situation in which you have a link with two
   routers, X and Y.  Router X is the best for 2002::/16.  (It's your
   6to4 site gateway.)  Router Y is the best for ::/0.  (It connects to
   the native IPv6 Internet.)  Router X forwards native IPv6 traffic to
   router Y; router Y forwards 6to4 traffic to router X.  If most
   traffic from this site is sent to 2002:/16 destinations, then router
   X is the one least likely to redirect.

   To make type A hosts work well, both routers should advertise
   themselves as default routers.  In particular, if router Y goes down,
   type A hosts should send traffic to router X to maintain 6to4
   connectivity, so router X and router Y need to be default routers.

   To make type B hosts work well, router X should advertise itself with
   a High default router preference.  This will cause type B hosts to
   prefer router X, minimizing the number of redirects.





Draves & Thaler             Standards Track                    [Page 11]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   To make type C hosts work well, router X should in addition advertise
   the ::/0 route with a Low preference and the 2002::/16 route with a
   Medium preference.  A type C host will end up with three routes in
   its routing table: ::/0 -> router X (Low), ::/0 -> router Y (Medium),
   2002::/16 -> router X (Medium).  It will send 6to4 traffic to router
   X and other traffic to router Y.  Type C hosts will not cause any
   redirects.

   Note that when type C hosts process the Router Advertisement from
   router X, the Low preference for ::/0 overrides the High default
   router preference.  If the ::/0 specific route were not present, then
   a type C host would apply the High default router preference to its
   ::/0 route to router X.

5.2.  Multi-Homed Host and Isolated Network

   In another scenario, a multi-homed host is connected to the Internet
   via router X on one link and to an isolated network via router Y on
   another link.  The multi-homed host might have a tunnel into a
   firewalled corporate network, or it might be directly connected to an
   isolated test network.

   In this situation, a type A multi-homed host (which has no default
   router preferences or more-specific routes) will have no way to
   intelligently choose between routers X and Y on its Default Router
   List.  Users of the host will see unpredictable connectivity
   failures, depending on the destination address and the choice of
   router.

   If the routers are configured appropriately, a multi-homed type B
   host in this same situation would have stable Internet connectivity,
   but would have no connectivity to the isolated test network.

   If the routers are configured appropriately, a multi-homed type C
   host in this same situation can correctly choose between routers X
   and Y.  For example, router Y on the isolated network should
   advertise a Route Information Option for the isolated network prefix.
   It might not advertise itself as a default router at all (zero Router
   Lifetime), or it might advertise itself as a default router with a
   Low preference.  Router X should advertise itself as a default router
   with a Medium preference.

6.  Security Considerations

   A malicious node could send Router Advertisement messages, specifying
   a High Default Router Preference or carrying specific routes, with
   the effect of pulling traffic away from legitimate routers.  However,
   a malicious node could easily achieve this same effect in other ways.



Draves & Thaler             Standards Track                    [Page 12]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   For example, it could fabricate Router Advertisement messages with a
   zero Router Lifetime from the other routers, causing hosts to stop
   using the other routes.  By advertising a specific prefix, this
   attack could be carried out in a less noticeable way.  However, this
   attack has no significant incremental impact on Internet
   infrastructure security.

   A malicious node could also include an infinite lifetime in a Route
   Information Option causing the route to linger indefinitely.  A
   similar attack already exists with Prefix Information Options in RFC
   2461, where a malicious node causes a prefix to appear as on-link
   indefinitely, resulting in a lack of connectivity if it is not.  In
   contrast, an infinite lifetime in a Route Information Option will
   cause router reachability probing to continue indefinitely, but will
   not result in a lack of connectivity.

   Similarly, a malicious node could also try to overload hosts with a
   large number of routes in Route Information Options, or with very
   frequent Route Advertisements.  Again, this same attack already
   exists with Prefix Information Options.

   [RFC3756] provides more details on the trust models, and there is
   work in progress in the SEND WG on securing router discovery messages
   that will address these problems.

7.  IANA Considerations

   Section 2.3 defines a new Neighbor Discovery [RFC2461] option, the
   Route Information Option, which has been assigned the value 24 within
   the numbering space for IPv6 Neighbor Discovery Option Formats.

8.  Acknowledgements

   The authors would like to acknowledge the contributions of Balash
   Akbari, Steve Deering, Robert Elz, Tony Hain, Bob Hinden, Christian
   Huitema, JINMEI Tatuya, Erik Nordmark, Pekka Savola, Kresimir
   Segaric, and Brian Zill.  The packet diagrams are derived from
   Neighbor Discovery [RFC2461].

9.  Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2461] Narten, T., Nordmark, E., and W. Simpson, "Neighbor
             Discovery for IP Version 6 (IPv6)", RFC 2461, December
             1998.




Draves & Thaler             Standards Track                    [Page 13]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


   [RFC3775] Johnson, D., Perkins, C., and J. Arkko, "Mobility Support
             in IPv6", RFC 3775, June 2004.

10.  Informative References

   [RFC2080] Malkin, G. and R. Minnear, "RIPng for IPv6", RFC 2080,
             January 1997.

   [RFC2893] Gilligan, R. and E. Nordmark, "Transition Mechanisms for
             IPv6 Hosts and Routers", RFC 2893, August 2000.

   [RFC3056] Carpenter, B. and K. Moore, "Connection of IPv6 Domains via
             IPv4 Clouds", RFC 3056, February 2001.

   [RFC3756] Nikander, P., Kempf, J., and E. Nordmark, "IPv6 Neighbor
             Discovery (ND) Trust Models and Threats", RFC 3756, May
             2004.

Authors' Addresses

   Richard Draves
   Microsoft Research
   One Microsoft Way
   Redmond, WA 98052

   Phone: +1 425 706 2268
   EMail: richdr@microsoft.com


   Dave Thaler
   Microsoft
   One Microsoft Way
   Redmond, WA 98052

   Phone: +1 425 703 8835
   EMail: dthaler@microsoft.com















Draves & Thaler             Standards Track                    [Page 14]

RFC 4191      Router Preferences and More-Specific Routes  November 2005


Full Copyright Statement

   Copyright (C) The Internet Society (2005).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET
   ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED,
   INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE
   INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at ietf-
   ipr@ietf.org.

Acknowledgement

   Funding for the RFC Editor function is currently provided by the
   Internet Society.







Draves & Thaler             Standards Track                    [Page 15]



ERRATA