CCAMP Working Group CCAMP GMPLS P&R Design Team Internet Draft Expiration Date: October 2002 Dimitri Papadimitriou (Alcatel) Eric Mannie (KPNQewst) Deborah Brungard (AT&T) Sudheer Dharanikota (Nayna) Jonathan Lang (Calient) Guangzhi Li (AT&T) Bala Rajagopalan (Tellium) Yakov Rekhter (Juniper) April 2002 Analysis Grid for GMPLS-based Recovery Mechanisms (including Protection and Restoration) draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026 [1]. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet- Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. For potential updates to the above required-text see: http://www.ietf.org/ietf/1id-guidelines.txt 1. Abstract This document provides an analysis grid that can be used to evaluate, compare and contrast the large amount of GMPLS based recovery mechanisms currently proposed in the CCAMP WG. A detailed analysis of each of the recovery phases as identified in [CCAMP- TERM] will be given using terminology as defined in [CCAMP-TERM]. The focus will be on transport plane survivability and recovery issues and ***not control plane resilience related aspects***. D.Papadimitriou et al. - Internet Draft û Expires October 2002 1 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 2. Conventions used in this document The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC-2119 [2]. 3. Introduction This document provides an analysis grid that can be used to evaluate, compare and contrast the large amount of GMPLS based recovery mechanisms currently proposed in the CCAMP WG. Here, the focus will only be on transport plane survivability and recovery issues and not on control plane resilience related aspects. Although the recovery mechanisms described in this document impose different requirements on recovery protocols, the protocol(s) specifications will not be covered in this document. Despite the fact that the concepts discussed here are technology independent, this document will implicitly focus on SONET/SDH and pre-OTN technologies except when specific details need to be considered (for instance, in the case of failure detection). Details for applicability to other technologies such as Optical Transport Networks (OTN) [ITUT-G709] will be covered in a future release of this document. In the present release, a detailed analysis is provided for each of the recovery phases as identified in [CCAMP-TERM]. Recovery implies that the following generic operations need to be performed when a LSP/Span failure (or any other event generating such failures) occurs: - Phase 1: Failure detection - Phase 2: Failure correlation - Phase 3: Failure localization and isolation - Phase 4: Failure notification - Phase 5: Recovery (Protection/Restoration) - Phase 6: Reversion (normalization) Failure detection, correlation, localization and notification phases together are referred to as fault management. Within a recovery domain, the entities involved during the recovery operations are defined in [CCAMP-TERM]; these entities include ingress, egress and intermediate nodes. In this document the term ôrecovery mechanismö will be used to cover both protection and restoration mechanisms. The specific terms protection and restoration will only be used when differentiation is required. Likewise the term ôfailureö is used to represent both signal failure and signal degradation. In addition, a clear distinction will be made between partitioning (horizontal hierarchy) and layering (vertical hierarchy). Any other recovery-related terminology used in this document conforms to the one defined in [CCAMP-TERM]. D.Papadimitriou et al. - Internet Draft û October 2002 2 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 4. Fault Management 4.1 Failure Detection Transport failure detection is the only phase that can not be achieved by the control plane alone since the latter needs a hook to the transmission plane to gather the resulting information. Therefore, by definition, failure detection is transport technology dependent (and so exceptionally, we keep here the ôtransport planeö terminology). As an example, SONET/SDH (see [G.707], [G.783] and [G.806]) provides supervision capabilities covering: - Continuity: monitors the integrity of the continuity of a trail (i.e. section or path). This operation is performed by monitoring the presence/absence of the signal. Examples are Loss of Signal (LOS) detection for the physical layer, Unequipped (UNEQ) Signal detection for the path layer, Server Signal Fail Detection (e.g. AIS) at the client layer. - Connectivity: monitors the integrity of the routing of the signal between end-points. Connectivity is normally only required if the layer provides flexible connectivity, either automatically (e.g. cross-connects controlled by the TMN) or manually (e.g. fiber distribution frame). An example is the Trail (i.e. section, path) Trace Identifier used at the different layers and the corresponding Trail Trace Identifier Mismatch detection. - Alignment: checks that the client and server layer frame start can be correctly recovered from the detection of loss of alignment. The specific processes depend on the signal/frame structure and may include: (multi-)frame alignement, pointer processing and alignment of several independent frames to a common frame start in case of inverse multiplexing. Loss of alignment is a generic term. Examples are loss of frame, loss of multi-frame, or loss of pointer. - Payload type: checks that compatible adaptation functions are used at the source and the sink. This is normally done by adding a signal type identifier at the source adaptation function and comparing it with the expected identifier at the sink. For instance, the payload signal label and the corresponding payload signal mismatch detection. - Signal Quality: monitors the performance of a signal. For instance, if the performance falls below a certain threshold a defect û excessive errors (EXC) or degraded signal (DEG) - is detected. D.Papadimitriou et al. - Internet Draft û October 2002 3 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 The most important point to keep in mind is that the supervision processes and the corresponding defect detection (used to initiate the next recovery phase(s)) result in either: - Signal Degrade (SD): A signal indicating that the associated data has degraded in the sense that a degraded defect (e.g. dDEG) condition is active. - Signal Fail (SF): A signal indicating that the associated data has failed in the sense that a signal interrupting near-end defect condition is active (as opposed to the degraded defect). In optical transport networks (OTN) equivalent supervision capabilities are provided at the section layers (OTS, OMS and OTUk) and at path layers (OCh and ODUk). Interested readers are referred to the ITU-T Recommendations [G.798] and [G.709] for more details. On the other hand, in pre-OTN networks, a failure may be masked by O/E/O based OLS (Optical Line System), preventing Photonic Cross- Connect (PXC) from detecting the failure. In such cases, failure detection may be assisted by out-of-band communication, such as the one considered in [LMP-WDM] protocol. The protocol defined in [LMP- WDM] provides IP [LMP] based control plane communication between the PXC and the OLS. Also, since PXCs are framing format independent, failure conditions can only be triggered either by detecting the absence of the optical signal or by measuring its quality. Both are out of the scope of this document. The following are typical failure conditions in pre-OTN networks: - Loss of Light (LoL): condition where the optical signal is not detected anymore on a given interfaceÆs receiver. - Signal degradation (SD): detection of the signal degradation over a specific period of time. - For SDH/Sonet payloads, all of the above-mentioned supervision capabilities can be used, resulting in SD or SF condition. In summary, the following cases are considered to illustrate the communication between detecting and reporting entities: - Co-located detecting and reporting entities: both the detecting and reporting entities are on the same node (e.g., SDH/SONET equipment, Opaque cross-connects, and in some cases for Transparent cross-connects, etc.). - Non co-located detecting and reporting entities: - with In-band communication between entities: Entities are separated but in-band communication is provided between them (e.g., APS, OXCÆs LOS, etc.). - with Out-of-band communication between entities: Entities are separated but out-of-band communication is provided between them (e.g., PXCÆs LOS, PXCÆs LOL, etc.). 4.2 Failure Correlation D.Papadimitriou et al. - Internet Draft û October 2002 4 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 A single failure (such as a span failure) can result into reporting multiple failures (such as individual connection failures). Such failures can be grouped i.e. correlated to reduce the communication on the reporting channel, for both in-band and out-of-band failure reporting. In such a scenario, it can be important to wait for certain period of time, typically called failure correlation time, and gather all the failures to report them as a group of failures (or simply group failure). For instance, this approach can be provided using LMP-WDM for pre-OTN networks (see [LMP-WDM]) or when using Signal Failure/Degrade Group in the SONET/SDH context. Note that a default average time interval during which failure correlation operation can be performed is difficult to provide since strongly dependent on the underlying network topology. Therefore, it can be advisable to provide a per node configurable failure correlation time. The detailed selection criteria for this time interval are outside of the scope of this document. When failure correlation is not provided, multiple failure indication messages may be sent out in response to a single failure (for instance, a fiber), each one containing a set of information on the failed working resources (for instance, the individual lambda LSP flowing through this fiber). This allows for a more prompt response but can potentially overload the control plane due to a large amount of failure notifications. 4.3 Failure Localization and Isolation The failure localization provides the information required to perform the sub-sequent recovery action(s) at the LSP/span end- points. However, in some cases, failure localization may be less urgent. This is particularly the case when edge-to-edge LSP recovery (edge referring to a domain end-node for instance) is performed based on a simple failure notification (including the identification of the failed working LSPs) while a more accurate localization can be performed after subsequent LSP recovery. Failure localization should be triggered immediately after fault detection phase. This operation can be performed at the transport management plane and/or the control plane level using dedicated signaling messages. When performed at the control plane level, a protocol such as LMP (see [LMP], Section 6) can be used for failure localization and isolation purposes. 4.4 Failure Notification Failure notification is used 1) to inform intermediate nodes that a LSP/span failure has occurred and has been detected 2) to inform the deciding entities (which can correspond to any intermediate or end- D.Papadimitriou et al. - Internet Draft û October 2002 5 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 point of the failed LSP/span) that the corresponding service is not available. In general, these deciding entities will be the ones taking the appropriate recovery decision. When co-located with the recovering entity, they will also perform the corresponding recovery action(s). Failure notification can be either provided by the transport or by the control plane. As an example, let us first briefly describe the failure notification mechanism defined at the SDH/SONET transport plane level (also referred to as maintenance signal supervision): - AIS (Alarm Indication Signal) occurs as a result of a failure condition such as Loss of Signal and is used to notify downstream nodes (of the appropriate layer processing) that a failure has occurred. AIS performs two functions 1) inform the intermediate nodes (with the appropriate layer monitoring capability) that a failure has been detected 2) notify the connection end-point that the service is no longer available. For a distributed control plane supporting one (or more) failure notification mechanism(s), regardless of the mechanismÆs actual implementation, the same capabilities are needed with more (or less) information provided about the LSPs/Spans under failure condition, their detailed status, etc. The most important difference between these mechanisms is related to the fact that transport plane notifications (as defined today) would initiate a protection scheme (such as those defined in [CCAMP-TERM]) or a restoration scheme via the management plane. On the other hand, using a failure notification mechanism through the control plane would provide the possibility to trigger either a protection or a restoration action via the control plane. Moreover, as specified in [GMPLS-SIG], notification message exchanges through a GMPLS control plane may not follow the same path as the LSP/spans they intent to notify the unavailability. In turn, this ensures a reliable and efficient failure notification mechanism. The other important properties to be met by the failure notification mechanism are mainly the following: - Notification messages must provide enough information such that the most efficient subsequent recovery action will be taken (in most of the recovery schemes this action is even deterministic) at the recovering entities. Remember here that the latter can be either intermediate or end-points through which normal traffic flows. Based on local policy, intermediate nodes may not use this information for subsequent recovery actions (see for instance the APS protocol phases as described in [CCAMP-TERM]). The trade-off here is to define what information the LSP/span end- points (more precisely, the deciding entity) needs in order for the recovering entity to take the best recovery action: if too few information is provided, the decision can not be optimal (notice D.Papadimitriou et al. - Internet Draft û October 2002 6 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 that in this eventuality, the important issue is to quantify the level of sub-optimality), if too much information is provided the control plane may be overloaded with unnecessary information and the aggregation/correlation of this notification information will be more complex and more time consuming to achieve. Notice that more detailed quantification of the amount of information to be exchanged and processed is strongly dependent on the failure notification protocol specification. - If the failure localization and isolation is not performed by one of the LSP/Span end-points or some intermediate points, they should receive enough information from the notification message in order to locate the failure otherwise they would need to (re-) initiate a failure localization and isolation action. - Avoiding so-called notification storms implies that failure detection output is correlated (i.e. alarm correlation) and aggregated at the node detecting the failure(s), failure notifications are directed to a restricted set of destinations (in general the end-points), notification suppression (i.e. alarm suppression) is provided in order to limit flooding in case of multiple and/or correlated failures appearing at several locations in the network - Alarm correlation and aggregation (at the failure detecting node) implies a consistent decisions based on the conditions for which a trade-off between fast convergence (at detecting node) and fast notification (implying that correlation and aggregation occurs at receiving end-points) can be found. 5. Recovery Mechanisms and Schemes 5.1 Transport vs. Control Plane Responsibilities TBD. 5.2 Technology in/dependent mechanisms TBD. 5.3 Efficiency of Control Plane based Recovery 5.3.1 In-band vs Out-of-band Signalling The nodes communicate through the use of IP control channels. Since two classes of transport mechanisms can be considered here i.e. in- band or out-of-band (through a dedicated physically diverse control network), the potential impact of the signalling transport mechanism is not a trivial issue. As such, the distinction between in-fiber in-band and in-fiber out- of-band signalling reduces to the consideration of a logically versus physically embedded control plane topology with respect to D.Papadimitriou et al. - Internet Draft û October 2002 7 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 the one of the transport plane. In the current scope of this document, since we assume that IP control channels between nodes must be continuously available in order to enable the exchange of recovery-related information and messages, one considers that both signalling transports provides at least either one logical channel or one physical channel between nodes. Therefore, the key issue when using in-band signalling is whether we can assume independence between the fault-tolerance capabilities of control plane and the failures affecting the transport plane (including the nodes). Note also that existing specifications like the OTN provide a limited form of independence for in-band signaling by assigning control traffic to a separate supervisory optical channel. 5.3.2 Impact of Uni- versus Bi-directional Failures The failure detection, correlation and notification mechanisms (described in Section 4) can be triggered when either a unidirectional or a bi-directional LSP/Span failure occurs (or a combination of both). As illustrated in Figure 1 and 2, two alternatives can be considered here: 1. Uni-directional failure detection: the failure is detected on the receiver side i.e. it is only is detected by the downstream node to the failure (or by the upstream node depending on the failure propagation direction, respectively) 2. Bi-directional failure detection: the failure is detected on the receiver side of both downstream node AND upstream node to the failure. Notice that after the failure detection time, if only control plane based failure management is provided, the peering node is unaware of the failure detection status of its neighbor. Ingress Egress ------- ------- ------- ------- | | | |Tx Rx| | | | | NodeA |----...----| NodeB |xxxxxxxxx| NodeC |----...----| NodeD | | |----...----| |---------| |----...----| | ------- ------- ------- ------- t0 >>>>>>> F t1 X <-------------+ Notification t2 <------- à ------+ +------ à --------> Up Notification Down Notification Ingress Egress ------- ------- ------- ------- D.Papadimitriou et al. - Internet Draft û October 2002 8 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 | | | |Tx Rx| | | | | NodeA |----...----| NodeB |xxxxxxxxx| NodeC |----...----| NodeD | | |----...----| |xxxxxxxxx| |----...----| | ------- ------- ------- ------- t0 F <<<<<<< >>>>>>> F t1 X <-------------> X Notification t2 <------- à ------+ +------ à --------> Up Notification Down Notification Fig. 1 & 2. Uni- and Bi-directional Failure Detection/Notification Subsequently the following failure management operations can be considered: - Each detecting entity sends a notification message to the corresponding transmitting entity. For instance, in Fig 1 (Fig 2), node C sends a notification message to node B (while node B sends a notification message to node A). To ensure reliable failure notification, a dedicated acknowledgment message can be returned back to the sender node. - After some period of time referred to as the failure correlation time (see above), in case of unidirectional failure node C can optionally send a downstream notification message to the egress node D while node B can optionally send a upstream notification to the ingress node A. In case of bi-directional failure, node B (and node C) correlates the received notification message with the corresponding local information before optionally sending the upstream notification message to the ingress node (egress node, respectively). In the above scenarios, the path followed by the notification messages does not have to be the same as the one followed by the failed LSP (see [GMPLS-SIG], for more details on the notification message exchange). The important point, concerning this mechanism, is that either the detecting/reporting entity (i.e. the nodes B and C) are also the deciding/recovery entity or the detecting/reporting entities are simply intermediate nodes in the subsequent recovery process. One refers to local recovery in the former case and to edge-to-edge recovery in the latter one. 5.4 Difference between LSP/LSP Segment and Span Recovery The recovery definitions given in [CCAMP-TERM] are quite generic and apply for link (or local span) and LSP recovery. The major difference between LSP and span recovery is related to the number of intermediate nodes the signalling messages have to travel. Since nodes are not necessarily adjacent in case of LSP recovery, signalling exchanges from the reporting to the deciding/recovery D.Papadimitriou et al. - Internet Draft û October 2002 9 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 entity will have to cross several intermediate nodes. This results in an additional propagation and forwarding delay, which can in certain circumstances be non-negligible e.g. in case of copper out- of-band network one has to consider approximately 1 ms per 200km. 5.5 Difference between Recovery Type and Scheme Section 4.6 of [CCAMP-TERM] defines the basic recovery types. The purpose of this section is to describe the schemes that can be built using these recovery types. Several examples are provided in order to illustrate the difference between a recovery type such as 1:1 and a recovery scheme such as (1:1)^n. 1. (1:1)^n with recovery resource sharing The exponent, n, indicates the number of times a 1:1 recovery type is applied between at most n different ingress-egress node pairs. Here, at most n pairs of disjoint recovery and working LSPs/spans share at most n times one unique common resource. Since the working LSPs/Spans are mutually disjoint, simultaneous requests for use of the shared resource will only occur in case of a simultaneous failures, which is less likely to happen. 2. (M:N)^n with recovery resource sharing The exponent, n, indicates the number of times a M:N recovery type is applied between at most n different ingress-egress node pairs. So the interpretation follows from the previous case, expect that here disjointness applies to the N working LSPs/spans and the N working and M recovery LSPs/spans while sharing at most n times M a common resources. In both schemes, one may see the following at the LSP level: we have a ôgroupö of sum{n=1}^N N{n} working LSPs and a pool of shared backup resources, not all of which are available to any given working path. In such conditions, defining a metric that describes the amount of overlap among the recovery LSPs would give some indication of the groupÆs ability to handle multiple simultaneous failures. For instance, in the simpler (1:1)^n case situation if n recovery LSPs in a (1:1)^n group overlap, then it can handle only single failures; any multiple working LSP failures will cause at least one working LSP to be denied automatic recovery. But if one consider for instance, a (1:1)^4 group in which there are two pairs of overlapping recovery LSPs, then two LSPs (belonging to the same pair) can be simultaneously recovered. 5.6 LSP Restoration Schemes This section briefly describes some LSP restoration schemes. 5.6.1 Overview D.Papadimitriou et al. - Internet Draft û October 2002 10 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 LSPs/spans recovery time depends on the proper recovery LSP (soft) provisioning and the level of recovery resources overbooking (i.e. over-provisioning). A proper balance of these two mechanisms will result in a desired LSP/span recovery time when single or multiple failure(s) occur(s). Recovery LSP Provisioning phases: (1) Route Computation --> On-demand | | --> Pre-Computed | | (2) Signalling --> On-demand | | --> Pre-Signaled | | (3) Resource Selection --> On-demand | | --> Pre-Selected Overbooking Levels: +----- Dedicated (for instance: 1+1, 1:1, etc.) | | +----- Shared (for instance: 1:N, M:N, etc.) | Level of | Overbooking -----+----- Unprotected (for instance: 0:1) Fig 3. LSP Provisioning and Overbooking Classification In this figure, we present a classification of different options under LSP provisioning and overbooking. Although we acknowledge these operations are run mostly during planning (using network planning) and provisioning time (using signaling and routing) activities, we keep them in analyzing the recovery schemes. Proper LSP/span provisioning will help in alleviating many of the failures. As an example, one may compute primary and secondary paths, either end-to-end or segment-per-segment, to recover an LSP from multiple failure events affecting link(s), node(s), SRLG(s) and/or SRG(s). Such primary and secondary LSP/span provisioning can be categorized, as shown in the above figure, based on: (1) the recovery path (i.e. route) can be either pre-computed or computed on demand. D.Papadimitriou et al. - Internet Draft û October 2002 11 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 (2) when the recovery path is pre-computed: pre-signaled (implying recovery resource reservation) or signaled on demand. (3) and when the recovery resources are reserved, they can be either pre-selected or selection on-demand. Note that these different options give rise to different LSP/span recovery times. The following subsections will consider all these cases in analyzing the schemes. There are many mechanisms available allowing the overbooking of the recovery resources. This overbooking can be done per LSP (such as the example mentioned above), per link (such as span protection) or per domain (such as ring topologies). In all these cases the level of overbooking, as shown in the above figure, can be classified as dedicated (such as 1+1 and 1:1), shared (such as 1:N and M:N) or unprotected (i.e. restorable if enough recovery resources are available). Under a shared restoration scheme one may support preemptable (preempt low priority connections in case of resource contention) extra-traffic. In this document we keep in mind all the above- mentioned overbooking mechanisms in analyzing the recovery schemes. 5.6.2 Dynamic LSP Restoration 1. With Route Pre-computation An end-to-end restoration LSP is established after the failure(s) occur(s) based on a pre-computed path (i.e. route). As such, one can define this as an ôLSP re-provisioningö mechanism. Here, one or more (disjoint) routes for the restoration path are computed (and optionally pre-selected) before a failure occurs. No reservation or selection of resources is performed along the restoration path before failure. As a result, there is no guarantee that a restoration connection is available when a failure occurs. 2. Without Route Pre-computation An end-to-end restoration LSP is established after the failure(s) occur(s). Here, one or more (disjoint) explicit route for the restoration path are dynamically computed and one is selected after failure. As such, one can define this as an ôLSP re-provisioningö mechanism. No reservation or selection of resources is performed along the restoration path before failure. As a result, there is no guarantee that a restoration connection is available when a failure occurs. Note: performance between the two approaches differs only by the time required for route computation (and selection). 5.6.3 Pre-signaled Restoration LSP D.Papadimitriou et al. - Internet Draft û October 2002 12 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 1. With resource reservation without pre-selection An end-to-end restoration path is pre-selected from a set of one or more pre-computed (disjoint) explicit route before failure. The restoration LSP is signaled along this pre-selected path to reserve resources (i.e. signaled) at each node but resources are not selected. In this case, the resources reserved for each restoration LSP may be dedicated or shared between different working LSP that are not expected to fail simultaneously. Local node policies can be applied to define the degree to which these resources are shared across independent failures. Upon failure detection, signaling is initiated along the restoration path to select the resources, and to perform the appropriate operation at each node entity involved in the restoration connection (e.g. cross-connections). 2. With resource reservation and pre-selection An end-to-end restoration path is pre-selected from a set of one or more pre-computed (disjoint) explicit route before failure. The restoration LSP is signaled along this pre-selected path to reserve AND select resources at each node but not cross-connected. Such that the selection of the recovery resources is fixed at the control plane level. However, no cross-connections are performed along the restoration path. In this case, the resources reserved for each restoration LSP may only be shared between different working LSPs that are not expected to fail simultaneously. Since one considers restoration schemes here, the sharing degree should not be limited to working (and recovery) LSPs starting and ending at the same ingress and egress nodes. Therefore, one expects to receive some feedback information on the recovery resource sharing degree at each node participating to the recovery scheme. Upon failure detection, signaling is initiated along the restoration path to activate the reserved and selected resources and to perform the appropriate operation at each node involved in the restoration connection (e.g. cross-connections). 5.6.3 LSP Segment Restoration The above approaches can be applied on a sub-network basis rather than end-to-end basis (in order to reduce the global recovery time). It should be also noted that using the horizontal hierarchical approach described in Section 7.1, that a given end-to-end LSP can be recovered by multiple recovery mechanisms (e.g. 1:1 protection in a metro edge network but M:N protection in the core). These D.Papadimitriou et al. - Internet Draft û October 2002 13 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 mechanisms are ideally independent and may even use different failure localization and notification mechanisms. 6. Normalization 6.1 Wait-to-Restore Used to prevent frequent operation of the protection switch due to an intermittent defect (e.g. BER fluctuating around the SD threshold). First, a failed LSP/span must become fault-free, e.g. a BER less than a certain recovery threshold. After the failed LSP/span (i.e. the previously working LSP/span) meets this criterion, a fixed period of time shall elapse before a normal traffic uses this/these resources again. This period called wait-to- restore (WTR) period is generally of the order of minute(s) (for instance, 5 minutes) and should be capable of being set. A SF or SD condition will override the WTR. 6.2 Revertive Mode Operation In revertive mode of operation, when the recovery LSP/span is no longer requested, i.e. the failed working LSP/span is no longer in SD or SF condition, a local Wait-to-Restore (WTR) state will be activated. Since this state becomes the highest in priority, signalling must maintain the normal traffic on the recovery LSP/span from the previously failed working LSP/span. During this WTR state no null traffic or extra traffic (if applicable) can be requested. Moreover, deactivation of the wait-to-restore timer may occur in case of higher priority request attempts. 6.3 Orphans When a reversion operation is requested normal traffic must be switched from the recovery to the ôrecoveredö working LSP/span. A particular situation occurs when the working LSP/span can not be recovered such that normal traffic can not be switched back. In such a case, the unrecoverable working LSP/span or segment (also referred to as ôorphanö) must be cleared. Otherwise, potential de- synchronization between the control and transport plane resource usage can appear. Several ways can be used for that purpose: wait for the elapsing of the clear-out time interval, initiate a deletion from the ingress or the egress node or trigger the initiation of deletion from an entity (such as an EMS or NMS) capable to react on the reception of an appropriate notification message. 7. Hierarchies 7.1 Horizontal Hierarchy (Partitioning) D.Papadimitriou et al. - Internet Draft û October 2002 14 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 A horizontal hierarchy is defined when partitioning a single layer network into multiple recovery domains. In the scope of this document these are referred as recovery domains. The scope of recovery may extend over a link (or span), LSP segment or even an end-to-end LSP. An administrative domain may consist of a single recovery domain or can be partitioned into several smaller recovery domains. The operator can configure multiple recovery domains; based on physical network topology, control plane scalability, or traffic engineering constraints. Example1: Metro-Core-Metro Application An example often addressed in the literature is the metro-core-metro application (sometimes extended to a metro-metro/core-core) within a single transport layer (see Section 6.2). For such a case, an end- to-end LSP is defined between the ingress and egress metro nodes, while LSP segments may be defined within the metro or core sub- network. This example shows that each of the topological structures determines a so-called ôrecovery domainö since each of these LSPs can have its own recovery type (or even scheme). Thus, the support of multiple recovery schemes within a domain is referred to as a multi-recovery domain. 7.2 Vertical Hierarchy (Layers) It is a very challenging task to combine in a coordinated manner the different recovery capabilities available across the path (i.e. switching capable) and section layers to ensure that certain network survivability objectives are met for the different services supported by the network. As a first analysis step, one can draw the following guidelines: - Fast convergence: the lower the layer the faster the convergence (notification) - Recovery time: the lower the layer the faster the recovery time - Flexibility (including granularity and resource sharing): the higher the layer the higher the flexibility and the finer the granularity of the recovery mechanisms A vertical hierarchy consists of multiple layered transport planes providing different: - Bandwidth granularities: . discrete for non-packet LSPs such as OCh, ODUk, HOVC/STS- SPE and LOVC/VT-SPE LSPs . continuous for packet LSPs - Potentially, recovery capabilities with different temporal granularities: from milliseconds to tens of seconds D.Papadimitriou et al. - Internet Draft û October 2002 15 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 In SDH/Sonet, typically one would consider for instance the LOVC/VT and HOVC/STS SPE as independent layers; LOVC/VT LSP using the underlying HOVC/STS SPE LSPs as links, for instance. In OTN, the ODUk path layers will lie on the OCh path layer i.e. the ODUk LSPs using the underlying OCh LSPs as links. Notice here that server layer LSPs may simply be provisioned and not dynamically triggered or established (control driven approach). The following figure (including only the path layers) illustrates the hierarchical layers that can be covered by the recovery architecture of a transmission network comprising a SDH/Sonet and an OTN part: LOVC <------------------------------------------------------> LOVC || || HOVC ==== HOVC <----------------------------------> HOVC ==== HOVC || || ODUk ==== ODUk <--------------> ODUk ==== ODUk || || OCh <---> OCh <---> OCh In this context, the important points are the following: - these layers are ***path*** layers; i.e. the ones controlled by the GMPLS protocol suite. - an LSP at the lower layer for instance an HOVC path (= network connection) appears as a section (= link) for the LOVC layer; sections that can be controlled by protocol such as LMP. Note: if one considers the section layers, at the OTH level for instance, then the following scheme applies: ODUk == . . . == ODUk <--------------> ODUk == . . . == ODUk || || OTUk <--------------> OTUk || || OCh <---> OCh <---> OCh The first key issue with multi-layer recovery is that achieving control plane individual or bulk LSP recovery will be as efficient as the underlying link (local span) recovery. In such a case, the span can be either protected or unprotected, but it MUST be recoverable. Therefore, the span recovery process can either be independent when protected (or restorable), or triggered by the upper LSP recovery process. The former requires coordination in order to achieve subsequent LSP recovery. Therefore, in order to achieve robustness and fast convergence, multi-layer recovery requires a fine-tuned coordination mechanism. D.Papadimitriou et al. - Internet Draft û October 2002 16 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 Moreover, in the absence of adequate recovery mechanism coordination, a fault notification may propagate from one layer to the next within a recovery hierarchy. It can engender "collisions" and simultaneous recovery actions that may lead to race conditions, reduced resource utilization, or instabilities [MANCHESTER]. Thus, a consistent escalation strategy is needed to coordinate recovery across several layers. Therefore, one can expect that the definition of the recovery mechanisms and protocol(s) is technology independent. In such a way, they can be used at different layers and subsequently simplify this coordination. Recovery Granularity: In a generic sense, the higher the layer, the finer the granularity. The OTN and SDH/Sonet Layers can only recover the whole Link/Span or the individual LSPs it transports whereas IP Layers can recover individual packets or groups of packets. Obviously, the recovery granularity at the sub-wavelength (i.e. SDH/Sonet) level would work only with O-E-O devices and not with all-optical ones except if recovery is provided end-to-end. Furthermore, the optical layer still may not provide recovery on a per-connection basis unless the Lambda-LSP was an entire wavelength or an entire sub-channel (in case of TDM-LSP) that the optical layer understands. 7.3 Escalation Strategies There are two types of escalation strategies (see [DEMEESTER]): bottom-up and top-down. The bottom-up approach assumes that lower layer recovery schemes are more expedient and faster than the upper layer one. Therefore we can inhibit or hold-off higher layer recovery. However this assumption is not entirely true. Imagine a SDH/Sonet based protection mechanism (with a less than 50 ms protection switching time) lying on top of an OTN restoration mechanism (with a less than 200 ms restoration time). Therefore, this assumption should be (at least) clarified as: lower layer recovery schemes are faster than upper level one but only if the same type of recovery mechanism is used at each layer (assuming that the lower layer one is faster). Consequently, taking into account the recovery actions at the different layers in a bottom-up approach, if lower layer recovery mechanisms are provided and sequentially activated in conjunction with higher layer ones, the lower layers MUST have an opportunity to recover normal traffic before the higher layers do. However, if lower layer recovery is slower than higher layer recovery, the lower layer MUST either communicate the failure related information to the higher layer(s) (and allow it to perform recovery), or use a hold- D.Papadimitriou et al. - Internet Draft û October 2002 17 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 off timer in order to temporarily set the higher layer recovery action in a ôstandby modeö. Note that the a priori information exchange between layers concerning their efficiency is not within the current of this document. Nevertheless, the coordination functionality between layers must be configurable and tunable. An example of coordination between the optical and packet layer control plane enables for instance letting the optical layer performing the failure management operations (in particular, failure detection and notification) while giving to the packet layer control plane the authority to perform the recovery actions. In case of packet layer unsuccessful recovery action, fallback at the optical layer can be subsequently performed. The Top-down approach attempts service recovery at the higher layers before invoking lower layer recovery. Higher layer recovery is service selective, and permits "per-CoS" or "per-connection" re- routing. With this approach, the most important aspect is that the upper layer must provide its own reliable and INDEPENDENT failure detection mechanism from the lower layer. The same reference suggests also recovery mechanisms incorporating a coordinated effort shared by two adjacent layers with periodic status updates. Moreover, at certain layers, some of these recovery operations can be pre-assigned, e.g. a particular link will be handled by the packet layer while another will be handled by the fiber layer. 7.4 Disjointness 7.4.1 Node and Link Disjointness Having working and recovery LSPs/Spans link (i.e. span) diverse and node diverse does not guarantee working and recovery LSPs/Spans disjointness. Due to the common physical layer topology (passive), additional concept such as the Shared Risk Link Group (SRLG) and mechanisms (diverse path computation) must be developed to provide a COMPLETE working and recovery LSP/span disjointness (see [IPO-IMP] and [CCAMP-SRLG]). Otherwise, a failure affecting the working LSP/span would also potentially affect the recovery LSP/span resources, one refers to such event as a common failure. 7.4.2 SRLG Disjointness A Shared Risk Link Group (SRLG) is defined as the set of optical spans (or links or optical lines) sharing a common physical resource (for instance, fiber links, fiber trunks or cables) i.e. sharing a common risk. For instance, a set of links L belongs to the same SRLG s, if they are provisioned over the same fiber link f. The SRLG properties can be summarized as follows: 1) A link belong to more than one SRLG if and only if it crosses one D.Papadimitriou et al. - Internet Draft û October 2002 18 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 of the resources covered by each of these sets 2) Two links belonging to the same SRLG can belong individually to other (one or more) SRLGs 3) The SRLG set S of an LSP is defined as the union of the SRLG s of the individual links composing this LSP 4) SRLG Disjointness for LSP The LSP SRLG disjointness concept is based on the following postulate: an LSP (i.e. sequence of links) cover an SRLG if and only if it crosses one of the links belonging to that SRLG. Therefore, the SRLG disjointness for LSPs can be defined as follows: two LSPs are disjoint with respect to an SRLG s if and only if none of them covers simultaneously this SRLG. While the LSP SRLG disjointness with respect of a set of SRLG S is defined when two LSPs are disjoint with respect to a set of SRLGs S if and only if the sets of SRLGs they cover are completely disjoint. The impact on recovery is obvious: SRLG disjointness is a necessary (but not necessarily sufficient) condition to ensure optical network survivability: with respect to the physical network resources, a working-protection LSP/span pair must be SRLG disjoint in case of dedicated recovery type while a working-protection LSP/span group must be SRLG disjoint in case of shared recovery. 7.4.3 SRG Disjointness By extending the previous definition from a link to a more generic structure, referred to as a ôrisk domainö, one comes to the SRG (Shared Risk Group) notion (see [CCAMP-SRG]). A risk domain is a group of arbitrarily connected nodes and spans that together can provide certain like-capabilities (such as a chain of dedicated/shared protected links and nodes, or a ring forming nodes and links, or a protected hierarchical TE Link). In turn, an SRG represents the risk domain capabilities and other parameters, which assist in computing diverse paths through the domain (it can also be used in assessing the risk associated with the risk domain.) Note that the SRLG set of a risk domain constitutes a subset of the SRGs. SRLGs address only risks associated with the links (physical) and passive elements within the risk domain, whereas SRGs contains nodes and other topological information in addition to the links. The key difference between an SRLG and an SRG is that an SRLG translates to only one link share risk with respect to server layer topology (even hierarchical TE Links) while an SRG translates a D.Papadimitriou et al. - Internet Draft û October 2002 19 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 sequence of SRLGs over the same layer from one source to one or more than one destination located within the same area. As for SRLG disjointness, the impact on recovery is: SRG disjointness is a necessary (but not necessarily sufficient) condition to ensure optical network survivability: with respect to the physical network resources and topology, a working-protection LSP/span pair must be SRG disjoint in case of dedicated recovery type while a working-protection LSP/span group must be SRG disjoint in case of shared recovery. 7.5 Summary concerning Hierarchies Recovery mechanisms are being made available at multiple (if not each) transport layers within so-called ôIP-over-opticalö networks. However, each layer has certain recovery features and one needs to determine the exact impact of the interaction between the recovery mechanisms provided by these layers. Nevertheless, the main idea is that the lower layers can provide coarse but fast recovery while the higher layers can provide finer but slower recovery. In any case it is more than desirable to avoid too many layers with functional overlaps. 8. Recovery Scheme/Strategy Selection In order to provide a structured selection and analysis of the recovery scheme/strategy, the following dimensions can be defined: 1. Fast convergence (performance): provide a mechanism that aggregates multiple failures (this implies fast failure detection and correlation mechanisms) and fast recovery decision independently of the number of failures occurring in the optical network (implying also a fast failure notification). 2. Efficiency (scalability): minimize the switching time required for LSP/span recovery independently of number of LSPs/spans being recovered (this implies an efficient failure correlation, a fast failure notification and timely efficient recovery mechanism(s)). 3. Robustness (availability): minimize the LSP/span downtime independently of the underlying topology of the transport plane (this implies a highly responsive recovery mechanism). 4. Resource optimization (efficiency): minimize the resource capacity, including LSP/span and nodes (switching capacity), required for recovery purposes; this dimension can also be referred to as optimize the sharing degree of the recovery resources. 5. Cost optimization: provide a cost-effective recovery strategy. D.Papadimitriou et al. - Internet Draft û October 2002 20 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 However, these dimensions are either out of the scope of this document such as cost optimization, recovery path computational aspects or going in opposite directions. For instance, it is obvious that providing a 1+1 recovery type for each LSP minimizes the LSP downtime (in case of failure) while being non-scalable and recovery resource consuming without enabling any extra-traffic. The following sections try to provide a first response in order to select a recovery strategy with respect to the dimensions described above and the recovery schemes proposed in [CCAMP-TERM]. 8.1 Fast Convergence (Detection/Correlation and Hold-off Time) Fast convergence is related to the failure management operations. It refers to the elapsing time between the failure detection/ correlation and hold-off time, point at which the recovery switching actions are initiated. This point has been already discussed in Section 4. 8.2 Efficiency (Switching Time) In general, the more pre-assignment/pre-planning of the recovery LSP/span, the more rapid the recovery scheme is. Since protection implies pre-assignment (and cross-connection in case of LSP recovery) of the protection resources, in general, protection schemes recover faster than restoration schemes. Span restoration (since using control plane) is also likely to be slower than most span protection types; however this greatly depends on the span restoration signalling efficiency. LSP Restoration with pre-signaled and pre-selected recovery resources is likely to be faster than fully dynamic LSP restoration, especially because of the elimination of any potential crank-back during the recovery LSP establishment. If one excludes the crank-back issue, the difference between dynamic and pre-planned restoration depends on the restoration path computation and path selection time. Since computational considerations are outside of the scope of this document, it is up to the vendor to determine the average path computation time in different scenarios and to the operator to decide whether or not dynamic restoration is advantageous over pre-planned schemes depending on the network environment. This difference depends also on the flexibility provided by pre-planned restoration with respect to dynamic one: the former implies a limited number of failure scenarios (that can be due for instance to local storage limitation). This, while the latter enables an on-demand path computation based on the information received through failure notification and as such more robust with respect to the failure scenario scope. Moreover, LSP segment restoration, in particular, dynamic restoration (i.e. no path pre-computation so none of the recovery D.Papadimitriou et al. - Internet Draft û October 2002 21 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 resource is pre-signaled) will generally be faster than end-to-end LSP schemes. However, local LSP restoration assumes that each LSP segment end-point has enough computational capacity to perform this operation while end-to-end requires only that LSP end-points provides this path computation capability. Recovery time objectives for SDH/Sonet protection switching (not including time to detect failure) are specified in [G.841] at 50 ms, taking into account constraints on distance, number of connections involved, and in the case of ring enhanced protection, number of nodes in the ring. Recovery time objectives for restoration mechanisms have been proposed through a separate effort [TE-RH]. 8.3 Robustness In general, the less pre-assignment (protection)/pre-planning (restoration) of the recovery LSP/span, the more robust the recovery type/scheme is to a variety of (single) failures, provided that adequate resources are available. Moreover, the pre-selection of recovery resources gives less flexibility for multiple failure scenarios than no recovery resource pre-selection. For instance, if failures occur that affect two LSPs that are sharing a common link along their restoration paths, then only one of these LSPs can be recovered. This, unless the restoration path of at least one of these LSPs is re-computed or the local resource assignment is modified on the fly. In addition, recovery schemes with pre-planned recovery resources, in particular spans for protection and LSP for restoration purposes, will not be able to recover from network failures that simultaneously affect both the working and recovery LSP/span. Thus, the recovery resources should ideally be chosen to be as disjoint as possible (with respect to link, node and SRLG disjoint), so that any single failure event will not affect both working and recovery LSP/span. In brief, working and recovery resource must be fully diverse in order to guarantee that a given failure will not affect simultaneously the working and the recovery LSP/span. Also, the risk of simultaneous failure of the working and restoration LSP can be reduced by re-computing the restoration path whenever a failure occurs along it or by re-computing a restoration path whenever a failure occurs along a working LSP/span. This method enables to maintain the number of available recovery path constant. The robustness of a recovery scheme is also determined by the amount of reserved (i.e. signaled) recovery resources within a given shared resource pool: as the amount of recovery resources sharing degree increases, the recovery scheme becomes less robust to multiple failure occurrences. Recovery schemes, in particular restoration, with pre-signaled resource reservation (with or without pre- selection) should be capable to reserve the adequate amount of resource to ensure recovery from any specific set of failure events, such as any single SRLG failure, any two SRLG failures etc. D.Papadimitriou et al. - Internet Draft û October 2002 22 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 8.4 Resource Optimization It is commonly admitted that sharing resources provides optimization. Therefore, from a resource utilization perspective, protection schemes are often classified with respect to their degree of sharing protection entities. 1+1 LSP/Span protection is the more resource consuming protection type since it doesnÆt allow any extra- traffic. 1:1 and 1:N LSP/span protection types require dedicated recovery LSP/span while allowing extra (preemptible) traffic. Obviously 1+1 and 1:1 protection type allow no protection resource sharing, while 1:N and in particular M:N protection type allow sharing of protection resources between several working LSP/spans. However the flexibility in usage of shared protection resources (in particular, shared protection links) is limited because of topology restrictions, e.g. fixed ring topology for traditional enhanced protection schemes. The degree to which restoration schemes allow sharing amongst multiple independent failures is directly dictated by the size of the restoration pool. In restoration schemes with re-provisioning, a pool of restoration resource can be defined from which all restoration routes are selected after failure. Thus, the degree of sharing is defined by the amount of available restoration capacity. In restoration with pre-signaled resource reservation, the amount of reserved restoration capacity is determined by the local bandwidth reservation policies. In all restoration schemes, pre-emptible LSP/span can use spare restoration resources when these resources are not being used for LSP/span recovery purposes. Clearly, less recovery resources (i.e. LSP/spans and switching capacity) have to be allocated to a shared recovery source pool if a greater sharing degree is required. Thus, the degree to which the network is survivable is determined by the policy that defines the amount of reserved (shared) recovery resources. Note: when sharing recovery resources, [GMPLS-RTG] through the use of the Maximum LSP bandwidth, the Maximum reservable bandwidth and the Unreserved bandwidth TE Link sub-TLVs provides the required parameters to obtain network resource optimization for a given recovery scheme, for instance (1:1)^n. However, one has to consider that the resource sharing degree, since its distribution per Link ID is by definition unknown, that a Maximum Sharing Degree information can be considered in order to optimize the usage of the shared resources. If one defines the shared recovery bandwidth (in terms bandwidth unit) per link i as r[i], this implies that the following quantity must be maximized: sum {i=1}^N [r{i}/t{i} û b{i}], where N is the total number of links traversed by a given LSP, t{i} the maximum reservable bandwidth per link[i] and b[i] as the sum of the bandwidth committed for working LSPs and dedicated recovery purposes per link[i]. Since b{i} =< t{i}, a fully provisioned link i, will D.Papadimitriou et al. - Internet Draft û October 2002 23 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 not be selected during the shared recovery path computation while a fully reserved link i would result in a ratio of 1. 8.5 Summary One can summarize by the following table the selection of a recovery scheme/strategy, using the recovery types proposed in [CCAMP-TERM] and the above discussion. -------------------------------------------------------------------- | Path Search (computation and selection) -------------------------------------------------------------------- | Pre-planned | Dynamic -------------------------------------------------------------------- | | faster recovery | Does not apply | | less flexible | | 1 | less robust | | | most resource consuming | Path | | | Setup --------------------------------------------------------- | | relatively fast recovery | Does not apply | | relatively flexible | | 2 | relatively robust | | | resource consumption | | | depends on sharing degree | --------------------------------------------------------- | | relatively fast recovery | less faster (computation) | | more flexible | most flexible | 3 | relatively robust | most robust | | resource consumption | less resource consuming | | depends on sharing degree | -------------------------------------------------------------------- 1. Path Setup with Resource Reservation (i.e. signalling) and Selection 2. Path Setup with Resource Reservation (i.e. signalling) w/o Selection 3. Path Setup w/o Resource Reservation (i.e. signalling) w/o Selection As defined in [CCAMP-TERM], the term pre-planned refers to restoration resource pre-computation, signaling (reservation) and a priori selection (optional), but not cross-connection. 8.6 Technology Dependence The above analysis applies in fact to any data oriented circuit technology with discrete bandwidth increments (like Sonet/SDH, G.709 OTN, etc.) being controlled by an IP-centric distributed control plane. NOTE: this section is not intended to favor one technology versus another, it just lists pro and cons for each of them in order to D.Papadimitriou et al. - Internet Draft û October 2002 24 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 determine the potential added value of GMPLS-based recovery in their respective context. 8.6.1 OTN Recovery OTN Recovery specifics are left for further considerations. 8.6.2 Pre-OTN Recovery Pre-OTN Recovery specifics (also referred to as ôlambda switchingö) presents mainly the following advantages: - benefits from a simpler architecture making it more suitable for meshed-based recovery schemes (on a per channel basis). - when providing suppression of intermediate node transponders implies also that failures (such as LoL) propagates until edge nodes giving the possibility to initiate upper layer driven recovery actions. The main disadvantage comes from the lack of interworking due to the large amount of failure management (in particular failure notification protocols) and recovery mechanisms currently available. 8.6.3 Sonet/SDH Recovery Some of the advantages of the Sonet/SDH and more generically any TDM layer are: - Protection schemes are standardized (see [G.841]) and can operate across protected domains and interwork (see [G.842]). - Provides failure detection, notification and Automatic Protection Switching (APS). - Provides greater control over the granularity of the TDM LPS/Links that can be recovered with respect to coarser optical channel (or whole fiber content) recovery switching Some of the current limitations of the Sonet/SDH layer recovery are: - Inefficient use of spare capacity: Sonet/SDH protection is largely applied for ring topologies, where spare capacity often remains idle, making the efficiency of bandwidth usage an issue. - Limited topological scope: Use of ring topologies (SNCP or Shared Protection Rings), reduces the flexibility to deploy somewhat more complex, but potentially more efficient, mesh-based recovery schemes. - Lack of traffic priority: as with the optical layer, the SDH/Sonet layer also cannot distinguish between different priorities of traffic. For example, it is not possible in SDH or Sonet to switch D.Papadimitriou et al. - Internet Draft û October 2002 25 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 EF (Expedited Forwarding) and AF (Assured Forwarding) upper layer packet flow streams based on priority. 9. Conclusion TBD. 10. Security Considerations This document does not introduce or imply any specific security consideration. 11. References [BRADNER1] Bradner, S., "The Internet Standards Process -- Revision 3", BCP 9, RFC 2026, October 1996. [BRADNER2] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [CCAMP-SRLG] D.Papadimitriou et al., ôInference of Shared Risk Link Groups,ö Internet Draft, Work in progress, draft-many-inference-srlg-02.txt, November 2001. [CCAMP-SRG] S.Dharanikota et al., ôInter domain routing with Shared Risk Groups,ö Internet Draft, Work in progress, November 2001. [CCAMP-TERM] E.Mannie and D.Papadimitriou (Editors), ôRecovery (Protection and Restoration) Terminology for GMPLS,ö Internet Draft, Work in progress, draft-design-team- gmpls-recovery-terminology-00.txt, February 2002. [DEMEESTER] P.Demeester et al., ôResilience in Multilayer Networksö, IEEE Communications Magazine, Vol. 37, No. 8, August 1998, pp. 70-76. [G.707] ITU-T Recommendation G.707, ôNetwork Node Interface for the Synchronous Digital Hierarchy (SDH)ö, April 2000. [G.709] ITU-T Recommendation G.709, ôNetwork Node Interface for the Optical Transport Network (OTN)ö, February 2001 (& Addendum, October 2001). [G.783] ITU-T Recommendation G.783, ôCharacteristics of Synchronous Digital Hierarchy (SDH) Equipment Functional Blocksö [G.798] ITU-T Recommendation G.798, ôCharacteristics of Optical Transport Network (OTN) Equipment Functional Blocksö D.Papadimitriou et al. - Internet Draft û October 2002 26 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 [G.806] ITU-T Recommendation G.806, ôCharacteristics of Transport Equipment û Description Methodology and Generic Functionalityö [G.826] ITU-T Recommendation G.826, ôPerformance Monitoringö [G.841] ITU-T Recommendation G.841, ôTypes and Characteristics of SDH Network Protection Architecturesö [G.842] ITU-T Recommendation G.842, ôInterworking of SDH network protection architecturesö [G.GPS] ITU-T G.GPS, Draft Version, ôGeneric Protection Switchingö, Work in progress, December 2001. [LMP-WDM] A.Fredette and J.Lang (Editors), ôLink Management Protocol (LMP) for DWDM Optical Line Systems,ö Internet Draft, Work in progress, draft-ietf-ccamp-lmp-wdm- 00.txt, February 2002. [LMP-WDM] J.Lang (Editor), ôLink Management Protocol (LMP) v1.0ö Internet Draft, Work in progress, draft-ietf-ccamp-lmp- 03.txt, February 2002. [MANCHESTER] J.Manchester, P.Bonenfant and C.Newton, ôThe Evolution of Transport Network Survivability,ö IEEE Communications Magazine, August 1999. [MPLS-REC] V.Sharma and F.Hellstrand (Editors), ôA Framework for MPLS Recoveryö, Internet Draft, Work in Progress, draft-ietf-mpls-recovery-frmwrk-03.txt, July 2001. [MPLS-OSU] S.Seetharaman et al, ôIP over Optical Networks: A Summary of Issuesö, Internet Draft, Work in Progress, draft-osu-ipo-mpls-issues-02.txt, April 2001. [TE-NS] K.Owens et al, ôNetwork Survivability Considerations for Traffic Engineered IP Networksö, Internet Draft, Work in Progress, draft-owens-te-network-survivability- 01.txt, July 2001. [TE-RH] W.Lai, D.McDysan, J.Boyle, et al, ôNetwork Hierarchy and Multi-layer Survivabilityö, Internet Draft, Work in Progress, draft-team-tewg-restore-hierarchy-00.txt, July 2001. 12. Acknowledgments The authors would like to thank Fabrice Poppe (Alcatel) and Bart Rousseau (Alcatel) for their revision effort, Richard Rabbat (Fujitsu) and David Griffith (NIST) for their useful comments. 13. Author's Addresses D.Papadimitriou et al. - Internet Draft û October 2002 27 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 Deborah Brungard AT&T Rm. D1-3C22 200 S. Laurel Ave. Middletown, NJ 07748, USA Email: dbrungard@att.com Sudheer Dharanikota Nayna Networks Inc 481 Sycamore Drive Milpitas, CA 95035, USA Email: sudheer@nayna.com Jonathan P. Lang Calient Networks 25 Castilian Goleta, CA 93117, USA Email: jplang@calient.net Guangzhi Li AT&T 180 Park Avenue, Florham Park, NJ 07932, USA Email: gli@research.att.com Phone: +1 973 360-7376 Eric Mannie KPNQwest Terhulpsesteenweg 6A 1560 Hoeilaart, Belgium Phone: +32 2 658-5652 Email: eric.mannie@ebone.com Dimitri Papadimitriou Alcatel Francis Wellesplein, 1 B-2018 Antwerpen, Belgium Phone: +32 3 240-8491 Email: dimitri.papadimitriou@alcatel.be Bala Rajagopalan Tellium, Inc. 2 Crescent Place P.O. Box 901 Oceanport, NJ 07757-0901, USA Phone: +1 732 923-4237 Email: braja@tellium.com Yakov Rekhter Juniper Email: yakov@juniper.net D.Papadimitriou et al. - Internet Draft û October 2002 28 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 D.Papadimitriou et al. - Internet Draft û October 2002 29 draft-papadimitriou-ccamp-gmpls-recovery-analysis-00.txt April 2002 Full Copyright Statement "Copyright (C) The Internet Society (date). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE." D.Papadimitriou et al. - Internet Draft û October 2002 30