SIDR D. Ma Internet-Draft ZDNS Intended status: Standards Track D. Mandelberg Expires: October 28, 2018 Unaffiliated T. Bruijnzeels RIPE NCC April 26, 2018 Simplified Local internet nUmber Resource Management with the RPKI (SLURM) draft-ietf-sidr-slurm-08 Abstract The Resource Public Key Infrastructure (RPKI) is a global authorization infrastructure that allows the holder of Internet Number Resources (INRs) to make verifiable statements about those resources. Network operators, e.g., Internet Service Providers (ISPs), can use the RPKI to validate BGP route origin assertions. ISPs can also use the RPKI to validate the path of a BGP route. However, ISPs may want to establish a local view of exceptions to the RPKI data in the form of local filters and additions. The mechanisms described in this document provide a simple way to enable INR holders to establish a local, customized view of the RPKI, overriding global RPKI repository data as needed. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on October 28, 2018. Ma, et al. Expires October 28, 2018 [Page 1] Internet-Draft RPKI Local Resource Management April 2018 Copyright Notice Copyright (c) 2018 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 2. RP with SLURM . . . . . . . . . . . . . . . . . . . . . . . . 4 3. SLURM File and Mechanisms . . . . . . . . . . . . . . . . . . 4 3.1. Use of JSON . . . . . . . . . . . . . . . . . . . . . . . 4 3.2. SLURM File Overview . . . . . . . . . . . . . . . . . . . 5 3.3. Validation Output Filters . . . . . . . . . . . . . . . . 6 3.3.1. Validated ROA Prefix Filters . . . . . . . . . . . . 6 3.3.2. BGPsec Assertion Filters . . . . . . . . . . . . . . 7 3.4. Locally Added Assertions . . . . . . . . . . . . . . . . 9 3.4.1. ROA Prefix Assertions . . . . . . . . . . . . . . . . 9 3.4.2. BGPsec Assertions . . . . . . . . . . . . . . . . . . 10 3.5. Example of a SLURM File with Filters and Assertions . . . 11 4. SLURM File Configuration . . . . . . . . . . . . . . . . . . 13 4.1. SLURM File Atomicity . . . . . . . . . . . . . . . . . . 13 4.2. Multiple SLURM Files . . . . . . . . . . . . . . . . . . 13 5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14 6. Security Considerations . . . . . . . . . . . . . . . . . . . 14 7. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 14 8. References . . . . . . . . . . . . . . . . . . . . . . . . . 15 8.1. Informative References . . . . . . . . . . . . . . . . . 15 8.2. Normative References . . . . . . . . . . . . . . . . . . 16 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 17 1. Introduction The Resource Public Key Infrastructure (RPKI) is a global authorization infrastructure that allows the holder of Internet Number Resources (INRs) to make verifiable statements about those resources. For example, the holder of a block of IP(v4 or v6) addresses can issue a Route Origin Authorization (ROA) [RFC6482] to Ma, et al. Expires October 28, 2018 [Page 2] Internet-Draft RPKI Local Resource Management April 2018 authorize an Autonomous System (AS) to originate routes for that block. Internet Service Providers (ISPs) can then use the RPKI to validate BGP routes. (Validation of the origin of a route is described in [RFC6811], and validation of the path of a route is described in [RFC8205].) However, an "RPKI relying party" (RP) may want to override some of the information expressed via configured Trust Anchors (TAs) and the certificates downloaded from the RPKI repository system. For instances, [RFC6491] recommends the creation of ROAs that would invalidate public routes for reserved and unallocated address space, yet some ISPs might like to use BGP and the RPKI with private address space ([RFC1918], [RFC4193], [RFC6598]) or private AS numbers ([RFC1930], [RFC6996]). Local use of private address space and/or AS numbers is consistent with the RFCs cited above, but such use cannot be verified by the global RPKI. This motivates creation of mechanisms that enable a network operator to publish exception to the RPKI in the form of filters and additions (for its own use and that of its customers) at its discretion. Additionally, a network operator might wish to make use of a local override capability to protect routes from adverse actions [RFC8211], until the results of such actions have been addressed. The mechanisms developed to provide this capability to network operators are hereby called Simplified Local internet nUmber Resource Management with the RPKI (SLURM). SLURM allows an operator to create a local view of the global RPKI by generating sets of assertions. For Origin Validation [RFC6811], an assertion is a tuple of {IP prefix, prefix length, maximum length, AS number (ASN)} as used by rpki-rtr (the RPKI to Router Protocol) version 0 [RFC6810] and rpki-rtr version 1 [RFC8210]. For BGPsec [RFC8205], an assertion is a tuple of {ASN, subject key identifier, router public key} as used by rpki-rtr version 1. (For the remainder of this document, these assertions are called ROA Prefix Assertions and BGPsec Assertions, respectively.) 1.1. Terminology The key words "MUST", "MUST NOT","REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here. Ma, et al. Expires October 28, 2018 [Page 3] Internet-Draft RPKI Local Resource Management April 2018 2. RP with SLURM SLURM provides a simple way to enable an RP to establish a local, customized view of the RPKI, by overriding RPKI repository data if needed. To that end, an RP with SLURM filters out (removes from consideration for routing decisions) any assertions in the RPKI that are overridden by local ROA Prefix Assertions and BGPsec Assertions. In general, the primary output of an RP is the data it sends to routers over the rpki-rtr protocol [RFC8210]. The rpki-rtr protocol enables routers to query an RP for all assertions it knows about (Reset Query) or for an update of only the changes in assertions (Serial Query). The mechanisms specified in this document are to be applied to the result set for a Reset Query, and to both the old and new sets that are compared for a Serial Query. RP software may modify other forms of output in comparable ways, but that is outside the scope of this document. +--------------+ +---------------------------+ +------------+ | | | | | | | Repositories +--->Local cache of RPKI objects+---> Validation | | | | | | | +--------------+ +---------------------------+ +-----+------+ | +-------------------------------------------------+ | +------v-------+ +------------+ +----------+ +-------------+ | | | | | | | | | SLURM +---> SLURM +---> rpki-rtr +---> BGP Speakers| | Filters | | Assertions | | | | | +--------------+ +------------+ +----------+ +-------------+ Figure 1: SLURM's Position in the RP Stack 3. SLURM File and Mechanisms 3.1. Use of JSON SLURM filters and assertions are specified in JSON [RFC8259] format. JSON members that are not defined here MUST NOT be used in SLURM Files. An RP MUST consider any deviations from the specification errors. Future additions to the specifications in this document MUST use an incremented value for the "slurmVersion" member. Ma, et al. Expires October 28, 2018 [Page 4] Internet-Draft RPKI Local Resource Management April 2018 3.2. SLURM File Overview A SLURM file consists of a single JSON object containing the following members: o A "slurmVersion" member that MUST be set to 1, encoded as a number o A "validationOutputFilters" member (Section 3.3), whose value is an object. The object MUST contain exactly two members: * A "prefixFilters" member, whose value is described in Section 3.3.1. * A "bgpsecFilters" member, whose value is described in Section 3.3.2. o A "locallyAddedAssertions" member (Section 3.4), whose value is an object. The object MUST contain exactly two members: * A "prefixAssertions" member, whose value is described in Section 3.4.1. * A "bgpsecAssertions" member, whose value is described in Section 3.4.2. In the envisioned typical use case, an RP uses both Validation Output Filters and Locally Added Assertions. In this case, the resulting assertions MUST be the same as if output filtering were performed before locally adding assertions. i.e. locally added assertions MUST NOT be removed by output filtering. The following JSON structure with JSON members represents a SLURM file that has no filters or assertions: Ma, et al. Expires October 28, 2018 [Page 5] Internet-Draft RPKI Local Resource Management April 2018 { "slurmVersion": 1, "validationOutputFilters": { "prefixFilters": [], "bgpsecFilters": [] }, "locallyAddedAssertions": { "prefixAssertions": [], "bgpsecAssertions": [] } } Empty SLURM File 3.3. Validation Output Filters 3.3.1. Validated ROA Prefix Filters The RP can configure zero or more Validated ROA Prefix Filters (Prefix Filters in short). Each Prefix Filter can contain either an IPv4 or IPv6 prefix and/or an ASN. It is RECOMMENDED that an explanatory comment is included with each Prefix Filter, so that it can be shown to users of the RP software. The above is expressed as a value of the "prefixFilters" member, as an array of zero or more objects. Each object MUST contain one of either, or one each of both following members: o A "prefix" member, whose value is string representing either an IPv4 prefix (Section 3.1 of [RFC4632]) or an IPv6 prefix ([RFC5952]). o An "asn" member, whose value is a number. In addition, each object MAY contain one optional "comment" member, whose value is a string. The following example JSON structure represents a "prefixFilters" member with an array of example objects for each use case listed above: Ma, et al. Expires October 28, 2018 [Page 6] Internet-Draft RPKI Local Resource Management April 2018 "prefixFilters": [ { "prefix": "192.0.2.0/24", "comment": "All VRPs encompassed by prefix" }, { "asn": 64496, "comment": "All VRPs matching ASN" }, { "prefix": "198.51.100.0/24", "asn": 64497, "comment": "All VRPs encompassed by prefix, matching ASN" } ] prefixFilters examples Any Validated ROA Prefix (VRP, [RFC6811]) that matches any configured Prefix Filter MUST be removed from the RP's output. A VRP is considered to match with a Prefix Filter if one of the following cases applies: 1. If the Prefix Filter contains an IPv4 or IPv6 Prefix only, the VRP is considered to match the filter if the VRP prefix is equal to or covered by the Prefix Filter prefix. 2. If Prefix Filter contains an ASN only, the VRP is considered to match the filter if the VRP ASN matches the Prefix Filter ASN. 3. If Prefix Filter contains both an IPv4 or IPv6 prefix and an ASN, the VRP is considered to match if the VRP prefix is equal to or covered by the Prefix Filter prefix and the VRP ASN matches the Prefix Filter ASN. 3.3.2. BGPsec Assertion Filters The RP can configure zero or more BGPsec Assertion Filters (BGPsec Filters in short). Each BGPsec Filter can contain an ASN and/or the Base64 [RFC4648] encoding of a Router Subject Key Identifier (SKI), as described in [RFC8209] and [RFC6487]. It is RECOMMENDED that an explanatory comment is also included with each BGPSec Filter, so that it can be shown to users of the RP software. Ma, et al. Expires October 28, 2018 [Page 7] Internet-Draft RPKI Local Resource Management April 2018 The above is expressed as a value of the "bgpsecFilters" member, as an array of zero or more objects. Each object MUST contain one of either, or one each of both following members: o An "asn" member, whose value is a number o An "SKI" member, whose value is the Base64 encoding without trailing '=' (Section 5 of [RFC4648]) of the certificate's Subject Public Key as described in Section 4.8.2. of [RFC6487] (This is the value of the ASN.1 OCTET STRING without the ASN.1 tag or length fields.) In addition, each object MAY contain one optional "comment" member, whose value is a string. The following example JSON structure represents a "bgpsecFilters" member with an array of example objects for each use case listed above: "bgpsecFilters": [ { "asn": 64496, "comment": "All keys for ASN" }, { "SKI": "", "comment": "Key matching Router SKI" }, { "asn": 64497, "SKI": "", "comment": "Key for ASN 64497 matching Router SKI" } ] bgpsecFilters examples Any BGPsec Assertion that matches any configured BGPsec Filter MUST be removed from the RP's output. A BGPsec Assertion is considered to match with a BGPsec Filter if one of the following cases applies: 1. If the BGPsec Filter contains an ASN only, a BGPsec Assertion is considered to match if the Assertion ASN matches the Filter ASN. Ma, et al. Expires October 28, 2018 [Page 8] Internet-Draft RPKI Local Resource Management April 2018 2. If the BGPsec Filter contains an SKI only, a BGPsec Assertion is considered to match if the Assertion Router SKI matches the Filter SKI. 3. If the BGPsec Filter contains both an ASN and a Router SKI, then a BGPsec Assertion is considered to match if both the Assertion ASN matches the Filter ASN and the Assertion Router SKI matches the Filter Router SKI. 3.4. Locally Added Assertions 3.4.1. ROA Prefix Assertions Each RP is locally configured with a (possibly empty) array of ROA Prefix Assertions (Prefix Assertion in short). Each ROA Prefix Assertion MUST contain an IPv4 or IPv6 prefix and an ASN. It MAY include a value for the maximum length. It is RECOMMENDED that an explanatory comment is also included with each, so that it can be shown to users ofthe RP software. The above is expressed as a value of the "prefixAssertions" member, as an array of zero or more objects. Each object MUST contain one each of both following members: o A "prefix" member, whose value is string representing either an IPv4 prefix (Section 3.1 of [RFC4632]) or an IPv6 prefix ([RFC5952]). o An "asn" member, whose value is a number. In addition, each object MAY contain one of each of the following members: o A "maxPrefixLength" member, whose value is a number. o A "comment" member, whose value is a string. The following example JSON structure represents a "prefixAssertions" member with an array of example objects for each use case listed above: Ma, et al. Expires October 28, 2018 [Page 9] Internet-Draft RPKI Local Resource Management April 2018 "prefixAssertions": [ { "asn": 64496, "prefix": "198.51.100.0/24", "comment": "My other important route" }, { "asn": 64496, "prefix": "2001:DB8::/32", "maxPrefixLength": 48, "comment": "My other important de-aggregated routes" } ] prefixAssertions examples Note that the combination of the prefix, ASN and optional maximum length describes a VRP as described in [RFC6811]. The RP MUST add all Prefix Assertions found this way to the VRP found through RPKI validation, and ensure that it sends the complete set of PDUs, excluding duplicates when using the rpki-rtr protocol, see Section 5.6 and 5.7 of [RFC8210]. 3.4.2. BGPsec Assertions Each RP is locally configured with a (possibly empty) array of BGPsec Assertions. Each BGPsec Assertion MUST contain an AS number, a Router SKI, and the Router Public Key. It is RECOMMENDED that an explanatory comment is also included, so that it can be shown to users of the RP software. The above is expressed as a value of the "bgpsecAssertions" member, as an array of zero or more objects. Each object MUST contain one each of all of the following members: An "asn" member, whose value is a number. An "SKI" member, whose value is the Base64 encoding without trailing '=' (Section 5 of RFC4648 ) of the router's public key equivalent to a certificate's Subject Public Key as described in Section 4.8.2. of [RFC6487]. This is the value of the ASN.1 OCTET STRING without the ASN.1 tag or length fields. A "routerPublicKey" member, whose value is is the Base64 encoding without trailing '=' (Section 5 of [RFC4648]) of the equivalent to a router certificate's public key's subjectPublicKeyInfo value, as described in [RFC8208]. This is the full ASN.1 DER encoding of Ma, et al. Expires October 28, 2018 [Page 10] Internet-Draft RPKI Local Resource Management April 2018 the subjectPublicKeyInfo, including the ASN.1 tag and length values of the subjectPublicKeyInfo SEQUENCE. The following JSON structure represents an array of "bgpsecAssertions" with one element as described above: "bgpsecAssertions": [ { "asn": 64496, "SKI": "", "publicKey": "", "comment": "My known key for my important ASN" } ] bgpsecAssertions examples Note that a bgpsecAssertion matches the syntax of the Router Key PDU described in section 5.10 of [RFC8210]. Relying Parties MUST add any bgpsecAssertion thus found to the set of Router PDUs, excluding duplicates, when using the RPKI-RTR protocol [RFC8210]. 3.5. Example of a SLURM File with Filters and Assertions The following JSON structure represents an example of a SLURM file that uses all the elements described in the previous sections: { "slurmVersion": 1, "validationOutputFilters": { "prefixFilters": [ { "prefix": "192.0.2.0/24", "comment": "All VRPs encompassed by prefix" }, { "asn": 64496, "comment": "All VRPs matching ASN" }, { "prefix": "198.51.100.0/24", "asn": 64497, "comment": "All VRPs encompassed by prefix, matching ASN" } ], Ma, et al. Expires October 28, 2018 [Page 11] Internet-Draft RPKI Local Resource Management April 2018 "bgpsecFilters": [ { "asn": 64496, "comment": "All keys for ASN" }, { "SKI": "Zm9v", "comment": "Key matching Router SKI" }, { "asn": 64497, "SKI": "YmFy", "comment": "Key for ASN 64497 matching Router SKI" } ] }, "locallyAddedAssertions": { "prefixAssertions": [ { "asn": 64496, "prefix": "198.51.100.0/24", "comment": "My other important route" }, { "asn": 64496, "prefix": "2001:DB8::/32", "maxPrefixLength": 48, "comment": "My other important de-aggregated routes" } ], "bgpsecAssertions": [ { "asn": 64496, "comment" : "My known key for my important ASN", "SKI": "", "publicKey": "" } ] } } Example of Full SLURM File Ma, et al. Expires October 28, 2018 [Page 12] Internet-Draft RPKI Local Resource Management April 2018 4. SLURM File Configuration 4.1. SLURM File Atomicity To ensure local consistency, the effect of SLURM MUST be atomic. That is, the output of the RP MUST be either the same as if SLURM file were not used, or it MUST reflect the entire SLURM configuration. For an example of why this is required, consider the case of two local routes for the same prefix but different origin ASNs. Both routes are configured with Locally Added Assertions. If neither addition occurs, then both routes could be in the unknown state [RFC6811]. If both additions occur then both routes would be in the valid state. However, if one addition occurs and the other does not, then one could be invalid while the other is valid. 4.2. Multiple SLURM Files An implementation MAY support the concurrent use of multiple SLURM files. In this case, the resulting inputs to Validation Output Filters and Locally Added Assertions are the respective unions of the inputs from each file. The envisioned typical use case for multiple files is when the files have distinct scopes. For instance, operators of two distinct networks may resort to one RP system to frame routing decisions. As such, they probably deliver SLURM files to this RP respectively. Before an RP configures SLURM files from different sources it MUST make sure there is no internal conflict among the INR assertions in these SLURM files. To do so, the RP SHOULD check the entries of SLURM file with regard to overlaps of the INR assertions and report errors to the sources that created these SLURM files in question. The RP gets multiple SLURM files as a set, and the whole set MUST be rejected in case of any overlaps among SLURM files. If a problem is detected with the INR assertions in these SLURM files, the RP MUST NOT use them, and SHOULD issue a warning as error report in the following cases: 1. There may be conflicting changes to ROA Prefix Assertions if there exists an IP address X and distinct SLURM files Y, Z such that X is contained by any prefix in any or in file Y and X is contained by any prefix in any or in file Z. 2. There may be conflicting changes to BGPsec Assertions if there exists an ASN X and distinct SLURM files Y, Z such that X is Ma, et al. Expires October 28, 2018 [Page 13] Internet-Draft RPKI Local Resource Management April 2018 used in any or in file Y and X is used in any or in file Z. 5. IANA Considerations None 6. Security Considerations The mechanisms described in this document provide a network operator with additional ways to control use of RPKI data while preserving autonomy in address space and ASN management. These mechanisms are applied only locally; they do not influence how other network operators interpret RPKI data. Nonetheless, care should be taken in how these mechanisms are employed. Note that it also is possible to use SLURM to (locally) manipulate assertions about non-private INRs, e.g., allocated address space that is globally routed. For example, a SLURM file may be used to override RPKI data that a network operator believes has been corrupted by an adverse action. Network operators who elect to use SLURM in this fashion should use extreme caution. The goal of the mechanisms described in this document is to enable an RP to create its own view of the RPKI, which is intrinsically a security function. An RP using a SLURM file is trusting the assertions made in that file. Errors in the SLURM file used by an RP can undermine the security offered by the RPKI, to that RP. It could declare as invalid ROAs that would otherwise be valid, and vice versa. As a result, an RP MUST carefully consider the security implications of the SLURM file being used, especially if the file is provided by a third party. Additionally, each RP using SLURM MUST ensure the authenticity and integrity of any SLURM file that it uses. Initially, the SLURM file may be pre-configured out of band, but if the RP updates its SLURM file over the network, it MUST verify the authenticity and integrity of the updated SLURM file. Yet the mechanism to update SLURM file to guarantee authenticity and integrity is out of the scope of this document. 7. Acknowledgments The authors would like to thank Stephen Kent for his guidance and detailed reviews of this document. Thanks go to to Richard Hansen for his careful reviews, to Hui Zou and Chunlin An for their editorial assistance. Ma, et al. Expires October 28, 2018 [Page 14] Internet-Draft RPKI Local Resource Management April 2018 8. References 8.1. Informative References [RFC1918] Rekhter, Y., Moskowitz, B., Karrenberg, D., de Groot, G., and E. Lear, "Address Allocation for Private Internets", BCP 5, RFC 1918, DOI 10.17487/RFC1918, February 1996, . [RFC1930] Hawkinson, J. and T. Bates, "Guidelines for creation, selection, and registration of an Autonomous System (AS)", BCP 6, RFC 1930, DOI 10.17487/RFC1930, March 1996, . [RFC4193] Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast Addresses", RFC 4193, DOI 10.17487/RFC4193, October 2005, . [RFC6482] Lepinski, M., Kent, S., and D. Kong, "A Profile for Route Origin Authorizations (ROAs)", RFC 6482, DOI 10.17487/RFC6482, February 2012, . [RFC6491] Manderson, T., Vegoda, L., and S. Kent, "Resource Public Key Infrastructure (RPKI) Objects Issued by IANA", RFC 6491, DOI 10.17487/RFC6491, February 2012, . [RFC6598] Weil, J., Kuarsingh, V., Donley, C., Liljenstolpe, C., and M. Azinger, "IANA-Reserved IPv4 Prefix for Shared Address Space", BCP 153, RFC 6598, DOI 10.17487/RFC6598, April 2012, . [RFC6810] Bush, R. and R. Austein, "The Resource Public Key Infrastructure (RPKI) to Router Protocol", RFC 6810, DOI 10.17487/RFC6810, January 2013, . [RFC6996] Mitchell, J., "Autonomous System (AS) Reservation for Private Use", BCP 6, RFC 6996, DOI 10.17487/RFC6996, July 2013, . [RFC8210] Bush, R. and R. Austein, "The Resource Public Key Infrastructure (RPKI) to Router Protocol, Version 1", RFC 8210, DOI 10.17487/RFC8210, September 2017, . Ma, et al. Expires October 28, 2018 [Page 15] Internet-Draft RPKI Local Resource Management April 2018 [RFC8211] Kent, S. and D. Ma, "Adverse Actions by a Certification Authority (CA) or Repository Manager in the Resource Public Key Infrastructure (RPKI)", RFC 8211, DOI 10.17487/RFC8211, September 2017, . 8.2. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4632] Fuller, V. and T. Li, "Classless Inter-domain Routing (CIDR): The Internet Address Assignment and Aggregation Plan", BCP 122, RFC 4632, DOI 10.17487/RFC4632, August 2006, . [RFC4648] Josefsson, S., "The Base16, Base32, and Base64 Data Encodings", RFC 4648, DOI 10.17487/RFC4648, October 2006, . [RFC5952] Kawamura, S. and M. Kawashima, "A Recommendation for IPv6 Address Text Representation", RFC 5952, DOI 10.17487/RFC5952, August 2010, . [RFC6487] Huston, G., Michaelson, G., and R. Loomans, "A Profile for X.509 PKIX Resource Certificates", RFC 6487, DOI 10.17487/RFC6487, February 2012, . [RFC6811] Mohapatra, P., Scudder, J., Ward, D., Bush, R., and R. Austein, "BGP Prefix Origin Validation", RFC 6811, DOI 10.17487/RFC6811, January 2013, . [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, May 2017, . [RFC8205] Lepinski, M., Ed. and K. Sriram, Ed., "BGPsec Protocol Specification", RFC 8205, DOI 10.17487/RFC8205, September 2017, . Ma, et al. Expires October 28, 2018 [Page 16] Internet-Draft RPKI Local Resource Management April 2018 [RFC8208] Turner, S. and O. Borchert, "BGPsec Algorithms, Key Formats, and Signature Formats", RFC 8208, DOI 10.17487/RFC8208, September 2017, . [RFC8209] Reynolds, M., Turner, S., and S. Kent, "A Profile for BGPsec Router Certificates, Certificate Revocation Lists, and Certification Requests", RFC 8209, DOI 10.17487/RFC8209, September 2017, . [RFC8259] Bray, T., Ed., "The JavaScript Object Notation (JSON) Data Interchange Format", STD 90, RFC 8259, DOI 10.17487/RFC8259, December 2017, . Authors' Addresses Di Ma ZDNS 4 South 4th St. Zhongguancun Haidian, Beijing 100190 China Email: madi@zdns.cn David Mandelberg Unaffiliated Email: david@mandelberg.org URI: https://david.mandelberg.org Tim Bruijnzeels RIPE NCC Stationsplein 11 Amsterdam 1012 AB Netherlands Email: tim@ripe.net Ma, et al. Expires October 28, 2018 [Page 17]