Routing Area Working Group G. Enyedi Internet-Draft A. Csaszar Intended status: Standards Track Ericsson Expires: August 19, 2016 A. Atlas C. Bowers Juniper Networks A. Gopalan University of Arizona February 16, 2016 An Algorithm for Computing Maximally Redundant Trees for IP/LDP Fast- Reroute draft-ietf-rtgwg-mrt-frr-algorithm-09 Abstract A solution for IP and LDP Fast-Reroute using Maximally Redundant Trees is presented in draft-ietf-rtgwg-mrt-frr-architecture. This document defines the associated MRT Lowpoint algorithm that is used in the Default MRT profile to compute both the necessary Maximally Redundant Trees with their associated next-hops and the alternates to select for MRT-FRR. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on August 19, 2016. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents Enyedi, et al. Expires August 19, 2016 [Page 1] Internet-Draft MRT FRR Algorithm February 2016 (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Requirements Language . . . . . . . . . . . . . . . . . . . . 5 3. Terminology and Definitions . . . . . . . . . . . . . . . . . 5 4. Algorithm Key Concepts . . . . . . . . . . . . . . . . . . . 6 4.1. Partial Ordering for Disjoint Paths . . . . . . . . . . . 7 4.2. Finding an Ear and the Correct Direction . . . . . . . . 8 4.3. Low-Point Values and Their Uses . . . . . . . . . . . . . 11 4.4. Blocks in a Graph . . . . . . . . . . . . . . . . . . . . 14 4.5. Determining Local-Root and Assigning Block-ID . . . . . . 16 5. MRT Lowpoint Algorithm Specification . . . . . . . . . . . . 18 5.1. Interface Ordering . . . . . . . . . . . . . . . . . . . 18 5.2. MRT Island Identification . . . . . . . . . . . . . . . . 21 5.3. GADAG Root Selection . . . . . . . . . . . . . . . . . . 21 5.4. Initialization . . . . . . . . . . . . . . . . . . . . . 22 5.5. Constructing the GADAG using lowpoint inheritance . . . . 23 5.6. Augmenting the GADAG by directing all links . . . . . . . 25 5.7. Compute MRT next-hops . . . . . . . . . . . . . . . . . . 29 5.7.1. MRT next-hops to all nodes ordered with respect to the computing node . . . . . . . . . . . . . . . . . 29 5.7.2. MRT next-hops to all nodes not ordered with respect to the computing node . . . . . . . . . . . . . . . . 30 5.7.3. Computing Redundant Tree next-hops in a 2-connected Graph . . . . . . . . . . . . . . . . . . . . . . . . 31 5.7.4. Generalizing for a graph that isn't 2-connected . . . 33 5.7.5. Complete Algorithm to Compute MRT Next-Hops . . . . . 34 5.8. Identify MRT alternates . . . . . . . . . . . . . . . . . 36 5.9. Named Proxy-Nodes . . . . . . . . . . . . . . . . . . . . 43 5.9.1. Determining Proxy-Node Attachment Routers . . . . . . 43 5.9.2. Computing if an Island Neighbor (IN) is loop-free . . 44 5.9.3. Computing MRT Next-Hops for Proxy-Nodes . . . . . . . 46 5.9.4. Computing MRT Alternates for Proxy-Nodes . . . . . . 52 6. MRT Lowpoint Algorithm: Next-hop conformance . . . . . . . . 60 7. Broadcast interfaces . . . . . . . . . . . . . . . . . . . . 60 7.1. Computing MRT next-hops on broadcast networks . . . . . . 61 7.2. Using MRT next-hops as alternates in the event of failures on broadcast networks . . . . . . . . . . . . . 62 8. Evaluation of Alternative Methods for Constructing GADAGs . . 63 9. Implementation Status . . . . . . . . . . . . . . . . . . . . 64 Enyedi, et al. Expires August 19, 2016 [Page 2] Internet-Draft MRT FRR Algorithm February 2016 10. Operational Considerations . . . . . . . . . . . . . . . . . 65 10.1. GADAG Root Selection . . . . . . . . . . . . . . . . . . 65 10.2. Destination-rooted GADAGs . . . . . . . . . . . . . . . 65 11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 66 12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 66 13. Security Considerations . . . . . . . . . . . . . . . . . . . 66 14. References . . . . . . . . . . . . . . . . . . . . . . . . . 66 14.1. Normative References . . . . . . . . . . . . . . . . . . 66 14.2. Informative References . . . . . . . . . . . . . . . . . 66 Appendix A. Python Implementation of MRT Lowpoint Algorithm . . 67 Appendix B. Constructing a GADAG using SPFs . . . . . . . . . . 108 Appendix C. Constructing a GADAG using a hybrid method . . . . . 113 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 115 1. Introduction MRT Fast-Reroute requires that packets can be forwarded not only on the shortest-path tree, but also on two Maximally Redundant Trees (MRTs), referred to as the MRT-Blue and the MRT-Red. A router which experiences a local failure must also have pre-determined which alternate to use. This document defines how to compute these three things for use in MRT-FRR and describes the algorithm design decisions and rationale. The algorithm is based on those presented in [MRTLinear] and expanded in [EnyediThesis]. The MRT Lowpoint algorithm is required for implementation when the Default MRT profile is implemented. Just as packets routed on a hop-by-hop basis require that each router compute a shortest-path tree which is consistent, it is necessary for each router to compute the MRT-Blue next-hops and MRT-Red next-hops in a consistent fashion. This document defines the MRT Lowpoint algorithm to be used as a standard in the default MRT profile for MRT-FRR. As now, a router's FIB will contain primary next-hops for the current shortest-path tree for forwarding traffic. In addition, a router's FIB will contain primary next-hops for the MRT-Blue for forwarding received traffic on the MRT-Blue and primary next-hops for the MRT- Red for forwarding received traffic on the MRT-Red. What alternate next-hops a point-of-local-repair (PLR) selects need not be consistent - but loops must be prevented. To reduce congestion, it is possible for multiple alternate next-hops to be selected; in the context of MRT alternates, each of those alternate next-hops would be equal-cost paths. This document defines an algorithm for selecting an appropriate MRT alternate for consideration. Other alternates, e.g. LFAs that are Enyedi, et al. Expires August 19, 2016 [Page 3] Internet-Draft MRT FRR Algorithm February 2016 downstream paths, may be preferred when available. See the Operational Considerations section of [I-D.ietf-rtgwg-mrt-frr-architecture] for a more detailed discussion of combining MRT alternates with those produced by other FRR technologies. [E]---[D]---| [E]<--[D]<--| [E]-->[D] | | | | ^ | | | | | V | | V [R] [F] [C] [R] [F] [C] [R] [F] [C] | | | ^ ^ | | | | | | | V | [A]---[B]---| [A]-->[B] [A]---[B]<--| (a) (b) (c) a 2-connected graph MRT-Blue towards R MRT-Red towards R Figure 1 The MRT Lowpoint algorithm can handle arbitrary network topologies where the whole network graph is not 2-connected, as in Figure 2, as well as the easier case where the network graph is 2-connected (Figure 1). Each MRT is a spanning tree. The pair of MRTs provide two paths from every node X to the root of the MRTs. Those paths share the minimum number of nodes and the minimum number of links. Each such shared node is a cut-vertex. Any shared links are cut- links. Enyedi, et al. Expires August 19, 2016 [Page 4] Internet-Draft MRT FRR Algorithm February 2016 [E]---[D]---| |---[J] | | | | | | | | | | [R] [F] [C]---[G] | | | | | | | | | | | [A]---[B]---| |---[H] (a) a graph that isn't 2-connected [E]<--[D]<--| [J] [E]-->[D]---| |---[J] | ^ | | | | | ^ V | | | V V V | [R] [F] [C]<--[G] | [R] [F] [C]<--[G] | ^ ^ ^ | ^ | | | | | | V | V | | [A]-->[B]---| |---[H] [A]<--[B]<--| [H] (b) MRT-Blue towards R (c) MRT-Red towards R Figure 2 2. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. 3. Terminology and Definitions Please see the Terminology section of [I-D.ietf-rtgwg-mrt-frr-architecture] for a complete list of terminology relevant to this draft. The list below does not repeat terminology introduced in that draft. spanning tree: A tree containing links that connects all nodes in the network graph. back-edge: In the context of a spanning tree computed via a depth- first search, a back-edge is a link that connects a descendant of a node x with an ancestor of x. partial ADAG: A subset of an ADAG that doesn't yet contain all the nodes in the block. A partial ADAG is created during the MRT algorithm and then expanded until all nodes in the block are included and it is an ADAG. DFS: Depth-First Search Enyedi, et al. Expires August 19, 2016 [Page 5] Internet-Draft MRT FRR Algorithm February 2016 DFS ancestor: A node n is a DFS ancestor of x if n is on the DFS- tree path from the DFS root to x. DFS descendant: A node n is a DFS descendant of x if x is on the DFS-tree path from the DFS root to n. ear: A path along not-yet-included-in-the-GADAG nodes that starts at a node that is already-included-in-the-GADAG and that ends at a node that is already-included-in-the-GADAG. The starting and ending nodes may be the same node if it is a cut-vertex. X >> Y or Y << X: Indicates the relationship between X and Y in a partial order, such as found in a GADAG. X >> Y means that X is higher in the partial order than Y. Y << X means that Y is lower in the partial order than X. X > Y or Y < X: Indicates the relationship between X and Y in the total order, such as found via a topological sort. X > Y means that X is higher in the total order than Y. Y < X means that Y is lower in the total order than X. X ?? Y: Indicates that X is unordered with respect to Y in the partial order. UNDIRECTED: In the GADAG, each link is marked as OUTGOING, INCOMING or both. Until the directionality of the link is determined, the link is marked as UNDIRECTED to indicate that its direction hasn't been determined. OUTGOING: A link marked as OUTGOING has direction in the GADAG from the interface's router to the remote end. INCOMING: A link marked as INCOMING has direction in the GADAG from the remote end to the interface's router. 4. Algorithm Key Concepts There are five key concepts that are critical for understanding the MRT Lowpoint algorithm. The first is the idea of partially ordering the nodes in a network graph with regard to each other and to the GADAG root. The second is the idea of finding an ear of nodes and adding them in the correct direction. The third is the idea of a Low-Point value and how it can be used to identify cut-vertices and to find a second path towards the root. The fourth is the idea that a non-2-connected graph is made up of blocks, where a block is a 2-connected cluster, a cut-link or an isolated node. The fifth is the idea of a local-root for each node; this is used to compute ADAGs in each block. Enyedi, et al. Expires August 19, 2016 [Page 6] Internet-Draft MRT FRR Algorithm February 2016 4.1. Partial Ordering for Disjoint Paths Given any two nodes X and Y in a graph, a particular total order means that either X < Y or X > Y in that total order. An example would be a graph where the nodes are ranked based upon their unique IP loopback addresses. In a partial order, there may be some nodes for which it can't be determined whether X << Y or X >> Y. A partial order can be captured in a directed graph, as shown in Figure 3. In a graphical representation, a link directed from X to Y indicates that X is a neighbor of Y in the network graph and X << Y. [A]<---[R] [E] R << A << B << C << D << E | ^ R << A << B << F << G << H << D << E | | V | Unspecified Relationships: [B]--->[C]--->[D] C and F | ^ C and G | | C and H V | [F]--->[G]--->[H] Figure 3: Directed Graph showing a Partial Order To compute MRTs, the root of the MRTs is at both the very bottom and the very top of the partial ordering. This means that from any node X, one can pick nodes higher in the order until the root is reached. Similarly, from any node X, one can pick nodes lower in the order until the root is reached. For instance, in Figure 4, from G the higher nodes picked can be traced by following the directed links and are H, D, E and R. Similarly, from G the lower nodes picked can be traced by reversing the directed links and are F, B, A, and R. A graph that represents this modified partial order is no longer a DAG; it is termed an Almost DAG (ADAG) because if the links directed to the root were removed, it would be a DAG. Enyedi, et al. Expires August 19, 2016 [Page 7] Internet-Draft MRT FRR Algorithm February 2016 [A]<---[R]<---[E] R << A << B << C << R | ^ ^ R << A << B << C << D << E << R | | | R << A << B << F << G << H << D << E << R V | | [B]--->[C]--->[D] Unspecified Relationships: | ^ C and F | | C and G V | C and H [F]--->[G]--->[H] Figure 4: ADAG showing a Partial Order with R lowest and highest Most importantly, if a node Y >> X, then Y can only appear on the increasing path from X to the root and never on the decreasing path. Similarly, if a node Z << X, then Z can only appear on the decreasing path from X to the root and never on the inceasing path. When following the increasing paths, it is possible to pick multiple higher nodes and still have the certainty that those paths will be disjoint from the decreasing paths. E.g. in the previous example node B has multiple possibilities to forward packets along an increasing path: it can either forward packets to C or F. 4.2. Finding an Ear and the Correct Direction For simplicity, the basic idea of creating a GADAG by adding ears is described assuming that the network graph is a single 2-connected cluster so that an ADAG is sufficient. Generalizing to multiple blocks is done by considering the block-roots instead of the GADAG root - and the actual algorithm is given in Section 5.5. In order to understand the basic idea of finding an ADAG, first suppose that we have already a partial ADAG, which doesn't contain all the nodes in the block yet, and we want to extend it to cover all the nodes. Suppose that we find a path from a node X to Y such that X and Y are already contained by our partial ADAG, but all the remaining nodes along the path are not added to the ADAG yet. We refer to such a path as an ear. Recall that our ADAG is closely related to a partial order. More precisely, if we remove root R, the remaining DAG describes a partial order of the nodes. If we suppose that neither X nor Y is the root, we may be able to compare them. If one of them is definitely lesser with respect to our partial order (say X<B---| A-->B---| (a) (b) (c) (a) A 2-connected graph (b) Partial ADAG (C is not included) (c) Resulting ADAG after adding path (or ear) B-C-D Figure 5 In this partial ADAG, node C is not yet included. However, we can find path B-C-D, where both endpoints are contained by this partial ADAG (we say those nodes are "ready" in the following text), and the remaining node (node C) is not contained yet. If we remove R, the remaining DAG defines a partial order, and with respect to this partial order we can say that B<C and C->D are added). If B >> D, we would add the same path in reverse direction. If in the partial order where an ear's two ends are X and Y, X << Y, then there must already be a directed path from X to Y in the ADAG. The ear must be added in a direction such that it doesn't create a cycle; therefore the ear must go from X to Y. In the case, when X and Y are not ordered with each other, we can select either direction for the ear. We have no restriction since neither of the directions can result in a cycle. In the corner case when one of the endpoints of an ear, say X, is the root (recall that the two endpoints must be different), we could use both directions again for the ear because the root can be considered both as smaller and as greater than Y. However, we strictly pick that direction in which the root is lower than Y. The logic for this decision is explained in Section 5.7 A partial ADAG is started by finding a cycle from the root R back to itself. This can be done by selecting a non-ready neighbor N of R and then finding a path from N to R that doesn't use any links between R and N. The direction of the cycle can be assigned either way since it is starting the ordering. Once a partial ADAG is already present, it will always have a node that is not the root R in it. As a brief proof that a partial ADAG Enyedi, et al. Expires August 19, 2016 [Page 9] Internet-Draft MRT FRR Algorithm February 2016 can always have ears added to it: just select a non-ready neighbor N of a ready node Q, such that Q is not the root R, find a path from N to the root R in the graph with Q removed. This path is an ear where the first node of the ear is Q, the next is N, then the path until the first ready node the path reached (that ready node is the other endpoint of the path). Since the graph is 2-connected, there must be a path from N to R without Q. It is always possible to select a non-ready neighbor N of a ready node Q so that Q is not the root R. Because the network is 2-connected, N must be connected to two different nodes and only one can be R. Because the initial cycle has already been added to the ADAG, there are ready nodes that are not R. Since the graph is 2-connected, while there are non-ready nodes, there must be a non- ready neighbor N of a ready node that is not R. Generic_Find_Ears_ADAG(root) Create an empty ADAG. Add root to the ADAG. Mark root as IN_GADAG. Select an arbitrary cycle containing root. Add the arbitrary cycle to the ADAG. Mark cycle's nodes as IN_GADAG. Add cycle's non-root nodes to process_list. while there exists connected nodes in graph that are not IN_GADAG Select a new ear. Let its endpoints be X and Y. if Y is root or (Y << X) add the ear towards X to the ADAG else // (a) X is root or (b)X << Y or (c) X, Y not ordered Add the ear towards Y to the ADAG Figure 6: Generic Algorithm to find ears and their direction in 2-connected graph The algorithm in Figure 6 merely requires that a cycle or ear be selected without specifying how. Regardless of the method for selecting the path, we will get an ADAG. The method used for finding and selecting the ears is important; shorter ears result in shorter paths along the MRTs. The MRT Lowpoint algorithm uses the Low-Point Inheritance method for constructing an ADAG (and ultimately a GADAG). This method is defined in Section 5.5. Other methods for constructing GADAGs are described in Appendix B and Appendix C. An evaluation of these different methods is given in Section 8 As an example, consider Figure 5 again. First, we select the shortest cycle containing R, which can be R-A-B-F-D-E (uniform link costs were assumed), so we get to the situation depicted in Figure 5 (b). Finally, we find a node next to a ready node; that must be node C and assume we reached it from ready node B. We search a path from Enyedi, et al. Expires August 19, 2016 [Page 10] Internet-Draft MRT FRR Algorithm February 2016 C to R without B in the original graph. The first ready node along this is node D, so the open ear is B-C-D. Since B<C and C->D to the ADAG. Since all the nodes are ready, we stop at this point. 4.3. Low-Point Values and Their Uses A basic way of computing a spanning tree on a network graph is to run a depth-first-search, such as given in Figure 7. This tree has the important property that if there is a link (x, n), then either n is a DFS ancestor of x or n is a DFS descendant of x. In other words, either n is on the path from the root to x or x is on the path from the root to n. global_variable: dfs_number DFS_Visit(node x, node parent) D(x) = dfs_number dfs_number += 1 x.dfs_parent = parent for each link (x, w) if D(w) is not set DFS_Visit(w, x) Run_DFS(node gadag_root) dfs_number = 0 DFS_Visit(gadag_root, NONE) Figure 7: Basic Depth-First Search algorithm Given a node x, one can compute the minimal DFS number of the neighbours of x, i.e. min( D(w) if (x,w) is a link). This gives the earliest attachment point neighbouring x. What is interesting, though, is what is the earliest attachment point from x and x's descendants. This is what is determined by computing the Low-Point value. In order to compute the low point value, the network is traversed using DFS and the vertices are numbered based on the DFS walk. Let this number be represented as DFS(x). All the edges that lead to already visited nodes during DFS walk are back-edges. The back-edges are important because they give information about reachability of a node via another path. The low point number is calculated by finding: Low(x) = Minimum of ( (DFS(x), Lowest DFS(n, x->n is a back-edge), Enyedi, et al. Expires August 19, 2016 [Page 11] Internet-Draft MRT FRR Algorithm February 2016 Lowest Low(n, x->n is tree edge in DFS walk) ). A detailed algorithm for computing the low-point value is given in Figure 8. Figure 9 illustrates how the lowpoint algorithm applies to a example graph. global_variable: dfs_number Lowpoint_Visit(node x, node parent, interface p_to_x) D(x) = dfs_number L(x) = D(x) dfs_number += 1 x.dfs_parent = parent x.dfs_parent_intf = p_to_x.remote_intf x.lowpoint_parent = NONE for each ordered_interface intf of x if D(intf.remote_node) is not set Lowpoint_Visit(intf.remote_node, x, intf) if L(intf.remote_node) < L(x) L(x) = L(intf.remote_node) x.lowpoint_parent = intf.remote_node x.lowpoint_parent_intf = intf else if intf.remote_node is not parent if D(intf.remote_node) < L(x) L(x) = D(intf.remote_node) x.lowpoint_parent = intf.remote_node x.lowpoint_parent_intf = intf Run_Lowpoint(node gadag_root) dfs_number = 0 Lowpoint_Visit(gadag_root, NONE, NONE) Figure 8: Computing Low-Point value Enyedi, et al. Expires August 19, 2016 [Page 12] Internet-Draft MRT FRR Algorithm February 2016 [E]---| [J]-------[I] [P]---[O] | | | | | | | | | | | | [R] [D]---[C]--[F] [H]---[K] [N] | | | | | | | | | | | | [A]--------[B] [G]---| [L]---[M] (a) a non-2-connected graph [E]----| [J]---------[I] [P]------[O] (5, ) | (10, ) (9, ) (16, ) (15, ) | | | | | | | | | | | | [R] [D]---[C]---[F] [H]----[K] [N] (0, ) (4, ) (3, ) (6, ) (8, ) (11, ) (14, ) | | | | | | | | | | | | [A]---------[B] [G]----| [L]------[M] (1, ) (2, ) (7, ) (12, ) (13, ) (b) with DFS values assigned (D(x), L(x)) [E]----| [J]---------[I] [P]------[O] (5,0) | (10,3) (9,3) (16,11) (15,11) | | | | | | | | | | | | [R] [D]---[C]---[F] [H]----[K] [N] (0,0) (4,0) (3,0) (6,3) (8,3) (11,11) (14,11) | | | | | | | | | | | | [A]---------[B] [G]----| [L]------[M] (1,0) (2,0) (7,3) (12,11) (13,11) (c) with low-point values assigned (D(x), L(x)) Figure 9: Example lowpoint value computation From the low-point value and lowpoint parent, there are three very useful things which motivate our computation. First, if there is a child c of x such that L(c) >= D(x), then there are no paths in the network graph that go from c or its descendants to an ancestor of x - and therefore x is a cut-vertex. In Figure 9, this can be seen by looking at the DFS children of C. C has two children - D and F and L(F) = 3 = D(C) so it is clear that C is a cut-vertex and F is in a block where C is the block's root. L(D) = 0 Enyedi, et al. Expires August 19, 2016 [Page 13] Internet-Draft MRT FRR Algorithm February 2016 < 3 = D(C) so D has a path to the ancestors of C; in this case, D can go via E to reach R. Comparing the low-point values of all a node's DFS-children with the node's DFS-value is very useful because it allows identification of the cut-vertices and thus the blocks. Second, by repeatedly following the path given by lowpoint_parent, there is a path from x back to an ancestor of x that does not use the link [x, x.dfs_parent] in either direction. The full path need not be taken, but this gives a way of finding an initial cycle and then ears. Third, as seen in Figure 9, even if L(x) < D(x), there may be a block that contains both the root and a DFS-child of a node while other DFS-children might be in different blocks. In this example, C's child D is in the same block as R while F is not. It is important to realize that the root of a block may also be the root of another block. 4.4. Blocks in a Graph A key idea for the MRT Lowpoint algorithm is that any non-2-connected graph is made up by blocks (e.g. 2-connected clusters, cut-links, and/or isolated nodes). To compute GADAGs and thus MRTs, computation is done in each block to compute ADAGs or Redundant Trees and then those ADAGs or Redundant Trees are combined into a GADAG or MRT. Enyedi, et al. Expires August 19, 2016 [Page 14] Internet-Draft MRT FRR Algorithm February 2016 [E]---| [J]-------[I] [P]---[O] | | | | | | | | | | | | [R] [D]---[C]--[F] [H]---[K] [N] | | | | | | | | | | | | [A]--------[B] [G]---| [L]---[M] (a) A graph with four blocks that are: three 2-connected clusters and one cut-link [E]<--| [J]<------[I] [P]<--[O] | | | ^ | ^ V | V | V | [R] [D]<--[C] [F] [H]<---[K] [N] ^ | ^ ^ | V | | [A]------->[B] [G]---| [L]-->[M] (b) MRT-Blue for destination R [E]---| [J]-------->[I] [P]-->[O] | | | V V V [R] [D]-->[C]<---[F] [H]<---[K] [N] ^ | ^ | ^ | | V | | | V [A]<-------[B] [G]<--| [L]<--[M] (c) MRT-Red for destination R Figure 10 Consider the example depicted in Figure 10 (a). In this figure, a special graph is presented, showing us all the ways 2-connected clusters can be connected. It has four blocks: block 1 contains R, A, B, C, D, E, block 2 contains C, F, G, H, I, J, block 3 contains K, L, M, N, O, P, and block 4 is a cut-link containing H and K. As can be observed, the first two blocks have one common node (node C) and blocks 2 and 3 do not have any common node, but they are connected through a cut-link that is block 4. No two blocks can have more than one common node, since two blocks with at least two common nodes would qualify as a single 2-connected cluster. Enyedi, et al. Expires August 19, 2016 [Page 15] Internet-Draft MRT FRR Algorithm February 2016 Moreover, observe that if we want to get from one block to another, we must use a cut-vertex (the cut-vertices in this graph are C, H, K), regardless of the path selected, so we can say that all the paths from block 3 along the MRTs rooted at R will cross K first. This observation means that if we want to find a pair of MRTs rooted at R, then we need to build up a pair of RTs in block 3 with K as a root. Similarly, we need to find another pair of RTs in block 2 with C as a root, and finally, we need the last pair of RTs in block 1 with R as a root. When all the trees are selected, we can simply combine them; when a block is a cut-link (as in block 4), that cut-link is added in the same direction to both of the trees. The resulting trees are depicted in Figure 10 (b) and (c). Similarly, to create a GADAG it is sufficient to compute ADAGs in each block and connect them. It is necessary, therefore, to identify the cut-vertices, the blocks and identify the appropriate local-root to use for each block. 4.5. Determining Local-Root and Assigning Block-ID Each node in a network graph has a local-root, which is the cut- vertex (or root) in the same block that is closest to the root. The local-root is used to determine whether two nodes share a common block. Compute_Localroot(node x, node localroot) x.localroot = localroot for each DFS child node c of x if L(c) < D(x) //x is not a cut-vertex Compute_Localroot(c, x.localroot) else mark x as cut-vertex Compute_Localroot(c, x) Compute_Localroot(gadag_root, gadag_root) Figure 11: A method for computing local-roots There are two different ways of computing the local-root for each node. The stand-alone method is given in Figure 11 and better illustrates the concept; it is used by the GADAG construction methods given in Appendix B and Appendix C. The MRT Lowpoint algorithm computes the local-root for a block as part of computing the GADAG using lowpoint inheritance; the essence of this computation is given in Figure 12. Both methods for computing the local-root produce the same results. Enyedi, et al. Expires August 19, 2016 [Page 16] Internet-Draft MRT FRR Algorithm February 2016 Get the current node, s. Compute an ear(either through lowpoint inheritance or by following dfs parents) from s to a ready node e. (Thus, s is not e, if there is such ear.) if s is e for each node x in the ear that is not s x.localroot = s else for each node x in the ear that is not s or e x.localroot = e.localroot Figure 12: Ear-based method for computing local-roots Once the local-roots are known, two nodes X and Y are in a common block if and only if one of the following three conditions apply. o Y's local-root is X's local-root : They are in the same block and neither is the cut-vertex closest to the root. o Y's local-root is X: X is the cut-vertex closest to the root for Y's block o Y is X's local-root: Y is the cut-vertex closest to the root for X's block Once we have computed the local-root for each node in the network graph, we can assign for each node, a block id that represents the block in which the node is present. This computation is shown in Figure 13. global_var: max_block_id Assign_Block_ID(x, cur_block_id) x.block_id = cur_block_id foreach DFS child c of x if (c.local_root is x) max_block_id += 1 Assign_Block_ID(c, max_block_id) else Assign_Block_ID(c, cur_block_id) max_block_id = 0 Assign_Block_ID(gadag_root, max_block_id) Figure 13: Assigning block id to identify blocks Enyedi, et al. Expires August 19, 2016 [Page 17] Internet-Draft MRT FRR Algorithm February 2016 5. MRT Lowpoint Algorithm Specification The MRT Lowpoint algorithm computes one GADAG that is then used by a router to determine its MRT-Blue and MRT-Red next-hops to all destinations. Finally, based upon that information, alternates are selected for each next-hop to each destination. The different parts of this algorithm are described below. o Order the interfaces in the network graph. [See Section 5.1] o Compute the local MRT Island for the particular MRT Profile. [See Section 5.2] o Select the root to use for the GADAG. [See Section 5.3] o Initialize all interfaces to UNDIRECTED. [See Section 5.4] o Compute the DFS value,e.g. D(x), and lowpoint value, L(x). [See Figure 8] o Construct the GADAG. [See Section 5.5] o Assign directions to all interfaces that are still UNDIRECTED. [See Section 5.6] o From the computing router x, compute the next-hops for the MRT- Blue and MRT-Red. [See Section 5.7] o Identify alternates for each next-hop to each destination by determining which one of the blue MRT and the red MRT the computing router x should select. [See Section 5.8] A Python implementation of this algorithm is given in Appendix A. 5.1. Interface Ordering To ensure consistency in computation, all routers MUST order interfaces identically down to the set of links with the same metric to the same neighboring node. This is necessary for the DFS in Lowpoint_Visit in Section 4.3, where the selection order of the interfaces to explore results in different trees. Consistent interface ordering is also necessary for computing the GADAG, where the selection order of the interfaces to use to form ears can result in different GADAGs. It is also necessary for the topological sort described in Section 5.8, where different topological sort orderings can result in undirected links being added to the GADAG in different directions. Enyedi, et al. Expires August 19, 2016 [Page 18] Internet-Draft MRT FRR Algorithm February 2016 The required ordering between two interfaces from the same router x is given in Figure 14. Interface_Compare(interface a, interface b) if a.metric < b.metric return A_LESS_THAN_B if b.metric < a.metric return B_LESS_THAN_A if a.neighbor.mrt_node_id < b.neighbor.mrt_node_id return A_LESS_THAN_B if b.neighbor.mrt_node_id < a.neighbor.mrt_node_id return B_LESS_THAN_A // Same metric to same node, so the order doesn't matter for // interoperability. return A_EQUAL_TO_B Figure 14: Rules for ranking multiple interfaces. Order is from low to high. In Figure 14, if two interfaces on a router connect to the same remote router with the same metric, the Interface_Compare function returns A_EQUAL_TO_B. This is because the order in which those interfaces are initially explored does not affect the final GADAG produced by the algorithm described here. While only one of the links will be added to the GADAG in the initial traversal, the other parallel links will be added to the GADAG with the same direction assigned during the procedure for assigning direction to UNDIRECTED links described in Section 5.6. An implementation is free to apply some additional criteria to break ties in interface ordering in this situation, but that criteria is not specified here since it will not affect the final GADAG produced by the algorithm. The Interface_Compare function in Figure 14 relies on the interface.metric and the interface.neighbor.mrt_node_id values to order interfaces. The exact source of these values for different IGPs and applications is specified in Figure 15. The metric and mrt_node_id values for OSPFv2, OSPFv3, and IS-IS provided here is normative. The metric and mrt_node_id values for ISIS-PCR in this table should be considered informational. The normative values are specified in [IEEE8021Qca] . Enyedi, et al. Expires August 19, 2016 [Page 19] Internet-Draft MRT FRR Algorithm February 2016 +--------------+-----------------------+-----------------------------+ | IGP/flooding | mrt_node_id | metric of | | protocol | of neighbor | interface | | and | on interface | | | application | | | +--------------+-----------------------+-----------------------------+ | OSPFv2 for | 4 octet Neighbor | 2 octet Metric field | | IP/LDP FRR | Router ID in | for corresponding | | | Link ID field for | point-to-point link | | | corresponding | in Router-LSA | | | point-to-point link | | | | in Router-LSA | | +--------------+-----------------------+-----------------------------+ | OSPFv3 for | 4 octet Neighbor | 2 octet Metric field | | IP/LDP FRR | Router ID field | for corresponding | | | for corresponding | point-to-point link | | | point-to-point link | in Router-LSA | | | in Router-LSA | | +--------------+-----------------------+-----------------------------+ | IS-IS for | 7 octet neighbor | 3 octet metric field | | IP/LDP FRR | system ID and | in Extended IS | | | pseudonode number | Reachability TLV #22 | | | in Extended IS | or Multi-Topology | | | Reachability TLV #22 | IS Neighbor TLV #222 | | | or Multi-Topology | | | | IS Neighbor TLV #222 | | +--------------+-----------------------+-----------------------------+ | ISIS-PCR for | 8 octet Bridge ID | 3 octet SPB-LINK-METRIC in | | protection | created from 2 octet | SPB-Metric sub-TLV (type 29)| | of traffic | Bridge Priority in | in Extended IS Reachability | | in bridged | SPB Instance sub-TLV | TLV #22 or Multi-Topology | | networks | (type 1) carried in | Intermediate Systems | | | MT-Capability TLV | TLV #222. In the case | | | #144 and 6 octet | of asymmetric link metrics, | | | neighbor system ID in | the larger link metric | | | Extended IS | is used for both link | | | Reachability TLV #22 | directions. | | | or Multi-Topology | (informational) | | | Intermediate Systems | | | | TLV #222 | | | | (informational) | | +--------------+-----------------------+-----------------------------+ Figure 15: value of interface.neighbor.mrt_node_id and interface.metric to be used for ranking interfaces, for different flooding protocols and applications Enyedi, et al. Expires August 19, 2016 [Page 20] Internet-Draft MRT FRR Algorithm February 2016 The metrics are unsigned integers and MUST be compared as unsigned integers. The results of mrt_node_id comparisons MUST be the same as would be obtained by converting the mrt_node_ids to unsigned integers using network byte order and performing the comparison as unsigned integers. In the case of IS-IS for IP/LDP FRR with point-to-point links, the pseudonode number (the 7th octet) is zero. Broadcast interfaces will be discussed in Section 7. 5.2. MRT Island Identification The local MRT Island for a particular MRT profile can be determined by starting from the computing router in the network graph and doing a breadth-first-search (BFS). The BFS explores only links that are in the same area/level, are not IGP-excluded, and are not MRT- ineligible. The BFS explores only nodes that are are not IGP- excluded, and that support the particular MRT profile. See section 7 of [I-D.ietf-rtgwg-mrt-frr-architecture] for more precise definitions of these criteria. MRT_Island_Identification(topology, computing_rtr, profile_id, area) for all routers in topology rtr.IN_MRT_ISLAND = FALSE computing_rtr.IN_MRT_ISLAND = TRUE explore_list = { computing_rtr } while (explore_list is not empty) next_rtr = remove_head(explore_list) for each intf in next_rtr if (not intf.MRT-ineligible and not intf.remote_intf.MRT-ineligible and not intf.IGP-excluded and (intf in area) and (intf.remote_node supports profile_id) ) intf.IN_MRT_ISLAND = TRUE intf.remote_node.IN_MRT_ISLAND = TRUE if (not intf.remote_node.IN_MRT_ISLAND)) intf.remote_node.IN_MRT_ISLAND = TRUE add_to_tail(explore_list, intf.remote_node) Figure 16: MRT Island Identification 5.3. GADAG Root Selection In Section 8.3 of [I-D.ietf-rtgwg-mrt-frr-architecture], the GADAG Root Selection Policy is described for the MRT default profile. This selection policy allows routers to consistently select a common GADAG Root inside the local MRT Island, based on advertised priority values. The MRT Lowpoint algorithm simply requires that all routers in the MRT Island MUST select the same GADAG Root; the mechanism can vary based upon the MRT profile description. Before beginning Enyedi, et al. Expires August 19, 2016 [Page 21] Internet-Draft MRT FRR Algorithm February 2016 computation, the network graph is reduced to contain only the set of routers that support the specific MRT profile whose MRTs are being computed. As noted in Section 7, pseudonodes MUST NOT be considered for GADAG root selection. It is expected that an operator will designate a set of routers as good choices for selection as GADAG root by setting the GADAG Root Selection Priority for that set of routers to lower (more preferred) numerical values. For guidance on setting the GADAG Root Selection Priority values, refer to Section 10.1. 5.4. Initialization Before running the algorithm, there is the standard type of initialization to be done, such as clearing any computed DFS-values, lowpoint-values, DFS-parents, lowpoint-parents, any MRT-computed next-hops, and flags associated with algorithm. It is assumed that a regular SPF computation has been run so that the primary next-hops from the computing router to each destination are known. This is required for determining alternates at the last step. Initially, all interfaces MUST be initialized to UNDIRECTED. Whether they are OUTGOING, INCOMING or both is determined when the GADAG is constructed and augmented. It is possible that some links and nodes will be marked using standard IGP mechanisms to discourage or prevent transit traffic. Section 7.3.1 of [I-D.ietf-rtgwg-mrt-frr-architecture] describes how those links and nodes are excluded from MRT Island formation. MRT-FRR also has the ability to advertise links MRT-Ineligible, as described in Section 7.3.2 of [I-D.ietf-rtgwg-mrt-frr-architecture]. These links are excluded from the MRT Island and the GADAG. Computation of MRT next-hops will therefore not use any MRT- ineligible links. The MRT algorithm does still need to consider MRT- ineligible links when computing FRR alternates, because an MRT- ineligible link can still be the shortest-path next-hop to reach a destination. When a broadcast interface is advertised as MRT-ineligible, then the pseudo-node representing the entire broadcast network MUST NOT be included in the MRT Island. This is equivalent to excluding all of the broadcast interfaces on that broadcast network from the MRT Island. Enyedi, et al. Expires August 19, 2016 [Page 22] Internet-Draft MRT FRR Algorithm February 2016 5.5. Constructing the GADAG using lowpoint inheritance As discussed in Section 4.2, it is necessary to find ears from a node x that is already in the GADAG (known as IN_GADAG). Two different methods are used to find ears in the algorithm. The first is by going to a not IN_GADAG DFS-child and then following the chain of low-point parents until an IN_GADAG node is found. The second is by going to a not IN_GADAG neighbor and then following the chain of DFS parents until an IN_GADAG node is found. As an ear is found, the associated interfaces are marked based on the direction taken. The nodes in the ear are marked as IN_GADAG. In the algorithm, first the ears via DFS-children are found and then the ears via DFS-neighbors are found. By adding both types of ears when an IN_GADAG node is processed, all ears that connect to that node are found. The order in which the IN_GADAG nodes is processed is, of course, key to the algorithm. The order is a stack of ears so the most recent ear is found at the top of the stack. Of course, the stack stores nodes and not ears, so an ordered list of nodes, from the first node in the ear to the last node in the ear, is created as the ear is explored and then that list is pushed onto the stack. Each ear represents a partial order (see Figure 4) and processing the nodes in order along each ear ensures that all ears connecting to a node are found before a node higher in the partial order has its ears explored. This means that the direction of the links in the ear is always from the node x being processed towards the other end of the ear. Additionally, by using a stack of ears, this means that any unprocessed nodes in previous ears can only be ordered higher than nodes in the ears below it on the stack. In this algorithm that depends upon Low-Point inheritance, it is necessary that every node have a low-point parent that is not itself. If a node is a cut-vertex, that may not yet be the case. Therefore, any nodes without a low-point parent will have their low-point parent set to their DFS parent and their low-point value set to the DFS- value of their parent. This assignment also properly allows an ear between two cut-vertices. Finally, the algorithm simultaneously computes each node's local- root, as described in Figure 12. This is further elaborated as follows. The local-root can be inherited from the node at the end of the ear unless the end of the ear is x itself, in which case the local-root for all the nodes in the ear would be x. This is because whenever the first cycle is found in a block, or an ear involving a bridge is computed, the cut-vertex closest to the root would be x itself. In all other scenarios, the properties of lowpoint/dfs Enyedi, et al. Expires August 19, 2016 [Page 23] Internet-Draft MRT FRR Algorithm February 2016 parents ensure that the end of the ear will be in the same block, and thus inheriting its local-root would be the correct local-root for all newly added nodes. The pseudo-code for the GADAG algorithm (assuming that the adjustment of lowpoint for cut-vertices has been made) is shown in Figure 17. Construct_Ear(x, Stack, intf, ear_type) ear_list = empty cur_node = intf.remote_node cur_intf = intf not_done = true while not_done cur_intf.UNDIRECTED = false cur_intf.OUTGOING = true cur_intf.remote_intf.UNDIRECTED = false cur_intf.remote_intf.INCOMING = true if cur_node.IN_GADAG is false cur_node.IN_GADAG = true add_to_list_end(ear_list, cur_node) if ear_type is CHILD cur_intf = cur_node.lowpoint_parent_intf cur_node = cur_node.lowpoint_parent else // ear_type must be NEIGHBOR cur_intf = cur_node.dfs_parent_intf cur_node = cur_node.dfs_parent else not_done = false if (ear_type is CHILD) and (cur_node is x) // x is a cut-vertex and the local root for // the block in which the ear is computed x.IS_CUT_VERTEX = true localroot = x else // Inherit local-root from the end of the ear localroot = cur_node.localroot while ear_list is not empty y = remove_end_item_from_list(ear_list) y.localroot = localroot push(Stack, y) Construct_GADAG_via_Lowpoint(topology, gadag_root) gadag_root.IN_GADAG = true gadag_root.localroot = None Initialize Stack to empty Enyedi, et al. Expires August 19, 2016 [Page 24] Internet-Draft MRT FRR Algorithm February 2016 push gadag_root onto Stack while (Stack is not empty) x = pop(Stack) foreach ordered_interface intf of x if ((intf.remote_node.IN_GADAG == false) and (intf.remote_node.dfs_parent is x)) Construct_Ear(x, Stack, intf, CHILD) foreach ordered_interface intf of x if ((intf.remote_node.IN_GADAG == false) and (intf.remote_node.dfs_parent is not x)) Construct_Ear(x, Stack, intf, NEIGHBOR) Construct_GADAG_via_Lowpoint(topology, gadag_root) Figure 17: Low-point Inheritance GADAG algorithm 5.6. Augmenting the GADAG by directing all links The GADAG, regardless of the method used to construct it, at this point could be used to find MRTs, but the topology does not include all links in the network graph. That has two impacts. First, there might be shorter paths that respect the GADAG partial ordering and so the alternate paths would not be as short as possible. Second, there may be additional paths between a router x and the root that are not included in the GADAG. Including those provides potentially more bandwidth to traffic flowing on the alternates and may reduce congestion compared to just using the GADAG as currently constructed. The goal is thus to assign direction to every remaining link marked as UNDIRECTED to improve the paths and number of paths found when the MRTs are computed. To do this, we need to establish a total order that respects the partial order described by the GADAG. This can be done using Kahn's topological sort[Kahn_1962_topo_sort] which essentially assigns a number to a node x only after all nodes before it (e.g. with a link incoming to x) have had their numbers assigned. The only issue with the topological sort is that it works on DAGs and not ADAGs or GADAGs. To convert a GADAG to a DAG, it is necessary to remove all links that point to a root of block from within that block. That provides the necessary conversion to a DAG and then a topological sort can be done. When adding undirected links to the GADAG, links connecting the block root to other nodes in that block need special handling because the topological order will not always give the right answer for those links. There are three cases to consider. If the undirected link in question has another parallel link between the Enyedi, et al. Expires August 19, 2016 [Page 25] Internet-Draft MRT FRR Algorithm February 2016 same two nodes that is already directed, then the direction of the undirected link can be inherited from the previously directed link. In the case of parallel cut links, we set all of the parallel links to both INCOMING and OUTGOING. Otherwise, the undirected link in question is set to OUTGOING from the block root node. A cut-link can then be identified by the fact that it will be directed both INCOMING and OUTGOING in the GADAG. The exact details of this whole process are captured in Figure 18 Add_Undirected_Block_Root_Links(topo, gadag_root) foreach node x in topo if x.IS_CUT_VERTEX or x is gadag_root foreach interface i of x if (i.remote_node.localroot is not x or i.PROCESSED ) continue Initialize bundle_list to empty bundle.UNDIRECTED = true bundle.OUTGOING = false bundle.INCOMING = false foreach interface i2 in x if i2.remote_node is i.remote_node add_to_list_end(bundle_list, i2) if not i2.UNDIRECTED: bundle.UNDIRECTED = false if i2.INCOMING: bundle.INCOMING = true if i2.OUTGOING: bundle.OUTGOING = true if bundle.UNDIRECTED foreach interface i3 in bundle_list i3.UNDIRECTED = false i3.remote_intf.UNDIRECTED = false i3.PROCESSED = true i3.remote_intf.PROCESSED = true i3.OUTGOING = true i3.remote_intf.INCOMING = true else if (bundle.OUTGOING and bundle.INCOMING) foreach interface i3 in bundle_list i3.UNDIRECTED = false i3.remote_intf.UNDIRECTED = false i3.PROCESSED = true i3.remote_intf.PROCESSED = true i3.OUTGOING = true i3.INCOMING = true i3.remote_intf.INCOMING = true i3.remote_intf.OUTGOING = true Enyedi, et al. Expires August 19, 2016 [Page 26] Internet-Draft MRT FRR Algorithm February 2016 else if bundle.OUTGOING foreach interface i3 in bundle_list i3.UNDIRECTED = false i3.remote_intf.UNDIRECTED = false i3.PROCESSED = true i3.remote_intf.PROCESSED = true i3.OUTGOING = true i3.remote_intf.INCOMING = true else if bundle.INCOMING foreach interface i3 in bundle_list i3.UNDIRECTED = false i3.remote_intf.UNDIRECTED = false i3.PROCESSED = true i3.remote_intf.PROCESSED = true i3.INCOMING = true i3.remote_intf.OUTGOING = true Modify_Block_Root_Incoming_Links(topo, gadag_root) foreach node x in topo if x.IS_CUT_VERTEX or x is gadag_root foreach interface i of x if i.remote_node.localroot is x if i.INCOMING: i.INCOMING = false i.INCOMING_STORED = true i.remote_intf.OUTGOING = false i.remote_intf.OUTGOING_STORED = true Revert_Block_Root_Incoming_Links(topo, gadag_root) foreach node x in topo if x.IS_CUT_VERTEX or x is gadag_root foreach interface i of x if i.remote_node.localroot is x if i.INCOMING_STORED i.INCOMING = true i.remote_intf.OUTGOING = true i.INCOMING_STORED = false i.remote_intf.OUTGOING_STORED = false Run_Topological_Sort_GADAG(topo, gadag_root) Modify_Block_Root_Incoming_Links(topo, gadag_root) foreach node x in topo node.unvisited = 0 foreach interface i of x if (i.INCOMING) node.unvisited += 1 Initialize working_list to empty Initialize topo_order_list to empty Enyedi, et al. Expires August 19, 2016 [Page 27] Internet-Draft MRT FRR Algorithm February 2016 add_to_list_end(working_list, gadag_root) while working_list is not empty y = remove_start_item_from_list(working_list) add_to_list_end(topo_order_list, y) foreach ordered_interface i of y if intf.OUTGOING i.remote_node.unvisited -= 1 if i.remote_node.unvisited is 0 add_to_list_end(working_list, i.remote_node) next_topo_order = 1 while topo_order_list is not empty y = remove_start_item_from_list(topo_order_list) y.topo_order = next_topo_order next_topo_order += 1 Revert_Block_Root_Incoming_Links(topo, gadag_root) def Set_Other_Undirected_Links_Based_On_Topo_Order(topo) foreach node x in topo foreach interface i of x if i.UNDIRECTED: if x.topo_order < i.remote_node.topo_order i.OUTGOING = true i.UNDIRECTED = false i.remote_intf.INCOMING = true i.remote_intf.UNDIRECTED = false else i.INCOMING = true i.UNDIRECTED = false i.remote_intf.OUTGOING = true i.remote_intf.UNDIRECTED = false Add_Undirected_Links(topo, gadag_root) Add_Undirected_Block_Root_Links(topo, gadag_root) Run_Topological_Sort_GADAG(topo, gadag_root) Set_Other_Undirected_Links_Based_On_Topo_Order(topo) Add_Undirected_Links(topo, gadag_root) Figure 18: Assigning direction to UNDIRECTED links Proxy-nodes do not need to be added to the network graph. They cannot be transited and do not affect the MRTs that are computed. The details of how the MRT-Blue and MRT-Red next-hops are computed for proxy-nodes and how the appropriate alternate next-hops are selected is given in Section 5.9. Enyedi, et al. Expires August 19, 2016 [Page 28] Internet-Draft MRT FRR Algorithm February 2016 5.7. Compute MRT next-hops As was discussed in Section 4.1, once a ADAG is found, it is straightforward to find the next-hops from any node X to the ADAG root. However, in this algorithm, we will reuse the common GADAG and find not only the one pair of MRTs rooted at the GADAG root with it, but find a pair rooted at each node. This is useful since it is significantly faster to compute. The method for computing differently rooted MRTs from the common GADAG is based on two ideas. First, if two nodes X and Y are ordered with respect to each other in the partial order, then an SPF along OUTGOING links (an increasing-SPF) and an SPF along INCOMING links (a decreasing-SPF) can be used to find the increasing and decreasing paths. Second, if two nodes X and Y aren't ordered with respect to each other in the partial order, then intermediary nodes can be used to create the paths by increasing/decreasing to the intermediary and then decreasing/increasing to reach Y. As usual, the two basic ideas will be discussed assuming the network is two-connected. The generalization to multiple blocks is discussed in Section 5.7.4. The full algorithm is given in Section 5.7.5. 5.7.1. MRT next-hops to all nodes ordered with respect to the computing node To find two node-disjoint paths from the computing router X to any node Y, depends upon whether Y >> X or Y << X. As shown in Figure 19, if Y >> X, then there is an increasing path that goes from X to Y without crossing R; this contains nodes in the interval [X,Y]. There is also a decreasing path that decreases towards R and then decreases from R to Y; this contains nodes in the interval [X,R-small] or [R-great,Y]. The two paths cannot have common nodes other than X and Y. [Y]<---(Cloud 2)<--- [X] | ^ | | V | (Cloud 3)--->[R]--->(Cloud 1) MRT-Blue path: X->Cloud 2->Y MRT-Red path: X->Cloud 1->R->Cloud 3->Y Figure 19: Y >> X Enyedi, et al. Expires August 19, 2016 [Page 29] Internet-Draft MRT FRR Algorithm February 2016 Similar logic applies if Y << X, as shown in Figure 20. In this case, the increasing path from X increases to R and then increases from R to Y to use nodes in the intervals [X,R-great] and [R-small, Y]. The decreasing path from X reaches Y without crossing R and uses nodes in the interval [Y,X]. [X]<---(Cloud 2)<--- [Y] | ^ | | V | (Cloud 3)--->[R]--->(Cloud 1) MRT-Blue path: X->Cloud 3->R->Cloud 1->Y MRT-Red path: X->Cloud 2->Y Figure 20: Y << X 5.7.2. MRT next-hops to all nodes not ordered with respect to the computing node When X and Y are not ordered, the first path should increase until we get to a node G, where G >> Y. At G, we need to decrease to Y. The other path should be just the opposite: we must decrease until we get to a node H, where H << Y, and then increase. Since R is smaller and greater than Y, such G and H must exist. It is also easy to see that these two paths must be node disjoint: the first path contains nodes in interval [X,G] and [Y,G], while the second path contains nodes in interval [H,X] and [H,Y]. This is illustrated in Figure 21. It is necessary to decrease and then increase for the MRT-Blue and increase and then decrease for the MRT-Red; if one simply increased for one and decreased for the other, then both paths would go through the root R. Enyedi, et al. Expires August 19, 2016 [Page 30] Internet-Draft MRT FRR Algorithm February 2016 (Cloud 6)<---[Y]<---(Cloud 5)<------------| | | | | V | [G]--->(Cloud 4)--->[R]--->(Cloud 1)--->[H] ^ | | | | | (Cloud 3)<---[X]<---(Cloud 2)<-----------| MRT-Blue path: decrease to H and increase to Y X->Cloud 2->H->Cloud 5->Y MRT-Red path: increase to G and decrease to Y X->Cloud 3->G->Cloud 6->Y Figure 21: X and Y unordered This gives disjoint paths as long as G and H are not the same node. Since G >> Y and H << Y, if G and H could be the same node, that would have to be the root R. This is not possible because there is only one incoming interface to the root R which is created when the initial cycle is found. Recall from Figure 6 that whenever an ear was found to have an end that was the root R, the ear was directed from R so that the associated interface on R is outgoing and not incoming. Therefore, there must be exactly one node M which is the largest one before R, so the MRT-Red path will never reach R; it will turn at M and decrease to Y. 5.7.3. Computing Redundant Tree next-hops in a 2-connected Graph The basic ideas for computing RT next-hops in a 2-connected graph were given in Section 5.7.1 and Section 5.7.2. Given these two ideas, how can we find the trees? If some node X only wants to find the next-hops (which is usually the case for IP networks), it is enough to find which nodes are greater and less than X, and which are not ordered; this can be done by running an increasing-SPF and a decreasing-SPF rooted at X and not exploring any links from the ADAG root. In principle, an traversal method other than SPF could be used to traverse the GADAG in the process of determining blue and red next- hops that result in maximally redundant trees. This will be the case as long as one traversal uses the links in the direction specified by the GADAG and the other traversal uses the links in the direction opposite of that specified by the GADAG. However, a different traversal algorithm will generally result in different blue and red next-hops. Therefore, the algorithm specified here requires the use Enyedi, et al. Expires August 19, 2016 [Page 31] Internet-Draft MRT FRR Algorithm February 2016 of SPF to traverse the GADAG to generate MRT blue and red next-hops, as described below. An increasing-SPF rooted at X and not exploring links from the root will find the increasing next-hops to all Y >> X. Those increasing next-hops are X's next-hops on the MRT-Blue to reach Y. A decreasing-SPF rooted at X and not exploring links from the root will find the decreasing next-hops to all Z << X. Those decreasing next- hops are X's next-hops on the MRT-Red to reach Z. Since the root R is both greater than and less than X, after this increasing-SPF and decreasing-SPF, X's next-hops on the MRT-Blue and on the MRT-Red to reach R are known. For every node Y >> X, X's next-hops on the MRT- Red to reach Y are set to those on the MRT-Red to reach R. For every node Z << X, X's next-hops on the MRT-Blue to reach Z are set to those on the MRT-Blue to reach R. For those nodes which were not reached by either the increasing-SPF or the decreasing-SPF, we can determine the next-hops as well. The increasing MRT-Blue next-hop for a node which is not ordered with respect to X is the next-hop along the decreasing MRT-Red towards R, and the decreasing MRT-Red next-hop is the next-hop along the increasing MRT-Blue towards R. Naturally, since R is ordered with respect to all the nodes, there will always be an increasing and a decreasing path towards it. This algorithm does not provide the complete specific path taken but just the appropriate next-hops to use. The identities of G and H are not determined by the computing node X. The final case to consider is when the GADAG root R computes its own next-hops. Since the GADAG root R is << all other nodes, running an increasing-SPF rooted at R will reach all other nodes; the MRT-Blue next-hops are those found with this increasing-SPF. Similarly, since the GADAG root R is >> all other nodes, running a decreasing-SPF rooted at R will reach all other nodes; the MRT-Red next-hops are those found with this decreasing-SPF. E---D---| E<--D<--| | | | | ^ | | | | V | | R F C R F C | | | | ^ ^ | | | V | | A---B---| A-->B---| (a) (b) A 2-connected graph A spanning ADAG rooted at R Figure 22 Enyedi, et al. Expires August 19, 2016 [Page 32] Internet-Draft MRT FRR Algorithm February 2016 As an example consider the situation depicted in Figure 22. Node C runs an increasing-SPF and a decreasing-SPF on the ADAG. The increasing-SPF reaches D, E and R and the decreasing-SPF reaches B, A and R. E>>C. So towards E the MRT-Blue next-hop is D, since E was reached on the increasing path through D. And the MRT-Red next-hop towards E is B, since R was reached on the decreasing path through B. Since E>>D, D will similarly compute its MRT-Blue next-hop to be E, ensuring that a packet on MRT-Blue will use path C-D-E. B, A and R will similarly compute the MRT-Red next-hops towards E (which is ordered less than B, A and R), ensuring that a packet on MRT-Red will use path C-B-A-R-E. C can determine the next-hops towards F as well. Since F is not ordered with respect to C, the MRT-Blue next-hop is the decreasing one towards R (which is B) and the MRT-Red next-hop is the increasing one towards R (which is D). Since F>>B, for its MRT-Blue next-hop towards F, B will use the real increasing next-hop towards F. So a packet forwarded to B on MRT-Blue will get to F on path C-B-F. Similarly, D will use the real decreasing next-hop towards F as its MRT-Red next-hop, a packet on MRT-Red will use path C-D-F. 5.7.4. Generalizing for a graph that isn't 2-connected If a graph isn't 2-connected, then the basic approach given in Section 5.7.3 needs some extensions to determine the appropriate MRT next-hops to use for destinations outside the computing router X's blocks. In order to find a pair of maximally redundant trees in that graph we need to find a pair of RTs in each of the blocks (the root of these trees will be discussed later), and combine them. When computing the MRT next-hops from a router X, there are three basic differences: 1. Only nodes in a common block with X should be explored in the increasing-SPF and decreasing-SPF. 2. Instead of using the GADAG root, X's local-root should be used. This has the following implications: A. The links from X's local-root should not be explored. B. If a node is explored in the outgoing SPF so Y >> X, then X's MRT-Red next-hops to reach Y uses X's MRT-Red next-hops to reach X's local-root and if Z << X, then X's MRT-Blue next- hops to reach Z uses X's MRT-Blue next-hops to reach X's local-root. Enyedi, et al. Expires August 19, 2016 [Page 33] Internet-Draft MRT FRR Algorithm February 2016 C. If a node W in a common block with X was not reached in the increasing-SPF or decreasing-SPF, then W is unordered with respect to X. X's MRT-Blue next-hops to W are X's decreasing (aka MRT-Red) next-hops to X's local-root. X's MRT-Red next- hops to W are X's increasing (aka MRT-Blue) next-hops to X's local-root. 3. For nodes in different blocks, the next-hops must be inherited via the relevant cut-vertex. These are all captured in the detailed algorithm given in Section 5.7.5. 5.7.5. Complete Algorithm to Compute MRT Next-Hops The complete algorithm to compute MRT Next-Hops for a particular router X is given in Figure 23. In addition to computing the MRT- Blue next-hops and MRT-Red next-hops used by X to reach each node Y, the algorithm also stores an "order_proxy", which is the proper cut- vertex to reach Y if it is outside the block, and which is used later in deciding whether the MRT-Blue or the MRT-Red can provide an acceptable alternate for a particular primary next-hop. In_Common_Block(x, y) if ( (x.block_id is y.block_id) or (x is y.localroot) or (y is x.localroot) ) return true return false Store_Results(y, direction) if direction is FORWARD y.higher = true y.blue_next_hops = y.next_hops if direction is REVERSE y.lower = true y.red_next_hops = y.next_hops SPF_No_Traverse_Block_Root(spf_root, block_root, direction) Initialize spf_heap to empty Initialize nodes' spf_metric to infinity and next_hops to empty spf_root.spf_metric = 0 insert(spf_heap, spf_root) while (spf_heap is not empty) min_node = remove_lowest(spf_heap) Store_Results(min_node, direction) if ((min_node is spf_root) or (min_node is not block_root)) foreach interface intf of min_node if ( ( ((direction is FORWARD) and intf.OUTGOING) or Enyedi, et al. Expires August 19, 2016 [Page 34] Internet-Draft MRT FRR Algorithm February 2016 ((direction is REVERSE) and intf.INCOMING) ) and In_Common_Block(spf_root, intf.remote_node) ) path_metric = min_node.spf_metric + intf.metric if path_metric < intf.remote_node.spf_metric intf.remote_node.spf_metric = path_metric if min_node is spf_root intf.remote_node.next_hops = make_list(intf) else intf.remote_node.next_hops = min_node.next_hops insert_or_update(spf_heap, intf.remote_node) else if path_metric == intf.remote_node.spf_metric if min_node is spf_root add_to_list(intf.remote_node.next_hops, intf) else add_list_to_list(intf.remote_node.next_hops, min_node.next_hops) SetEdge(y) if y.blue_next_hops is empty and y.red_next_hops is empty SetEdge(y.localroot) y.blue_next_hops = y.localroot.blue_next_hops y.red_next_hops = y.localroot.red_next_hops y.order_proxy = y.localroot.order_proxy Compute_MRT_NextHops(x, gadag_root) foreach node y y.higher = y.lower = false clear y.red_next_hops and y.blue_next_hops y.order_proxy = y SPF_No_Traverse_Block_Root(x, x.localroot, FORWARD) SPF_No_Traverse_Block_Root(x, x.localroot, REVERSE) // red and blue next-hops are stored to x.localroot as different // paths are found via the SPF and reverse-SPF. // Similarly any nodes whose local-root is x will have their // red_next_hops and blue_next_hops already set. // Handle nodes in the same block that aren't the local-root foreach node y if (y.IN_MRT_ISLAND and (y is not x) and (y.block_id is x.block_id) ) if y.higher y.red_next_hops = x.localroot.red_next_hops else if y.lower y.blue_next_hops = x.localroot.blue_next_hops else y.blue_next_hops = x.localroot.red_next_hops y.red_next_hops = x.localroot.blue_next_hops Enyedi, et al. Expires August 19, 2016 [Page 35] Internet-Draft MRT FRR Algorithm February 2016 // Inherit next-hops and order_proxies to other components if (x is not gadag_root) and (x.localroot is not gadag_root) gadag_root.blue_next_hops = x.localroot.blue_next_hops gadag_root.red_next_hops = x.localroot.red_next_hops gadag_root.order_proxy = x.localroot foreach node y if (y is not gadag_root) and (y is not x) and y.IN_MRT_ISLAND SetEdge(y) max_block_id = 0 Assign_Block_ID(gadag_root, max_block_id) Compute_MRT_NextHops(x, gadag_root) Figure 23 5.8. Identify MRT alternates At this point, a computing router S knows its MRT-Blue next-hops and MRT-Red next-hops for each destination in the MRT Island. The primary next-hops along the SPT are also known. It remains to determine for each primary next-hop to a destination D, which of the MRTs avoids the primary next-hop node F. This computation depends upon data set in Compute_MRT_NextHops such as each node y's y.blue_next_hops, y.red_next_hops, y.order_proxy, y.higher, y.lower and topo_orders. Recall that any router knows only which are the nodes greater and lesser than itself, but it cannot decide the relation between any two given nodes easily; that is why we need topological ordering. For each primary next-hop node F to each destination D, S can call Select_Alternates(S, D, F, primary_intf) to determine whether to use the MRT-Blue or MRT-Red next-hops as the alternate next-hop(s) for that primary next hop. The algorithm is given in Figure 24 and discussed afterwards. Select_Alternates_Internal(D, F, primary_intf, D_lower, D_higher, D_topo_order): if D_higher and D_lower if F.HIGHER and F.LOWER if F.topo_order < D_topo_order return USE_RED else return USE_BLUE if F.HIGHER return USE_RED if F.LOWER return USE_BLUE //F unordered wrt S Enyedi, et al. Expires August 19, 2016 [Page 36] Internet-Draft MRT FRR Algorithm February 2016 return USE_RED_OR_BLUE else if D_higher if F.HIGHER and F.LOWER return USE_BLUE if F.LOWER return USE_BLUE if F.HIGHER if (F.topo_order > D_topo_order) return USE_BLUE if (F.topo_order < D_topo_order) return USE_RED //F unordered wrt S return USE_RED_OR_BLUE else if D_lower if F.HIGHER and F.LOWER return USE_RED if F.HIGHER return USE_RED if F.LOWER if F.topo_order > D_topo_order return USE_BLUE if F.topo_order < D_topo_order return USE_RED //F unordered wrt S return USE_RED_OR_BLUE else //D is unordered wrt S if F.HIGHER and F.LOWER if primary_intf.OUTGOING and primary_intf.INCOMING return USE_RED_OR_BLUE if primary_intf.OUTGOING return USE_BLUE if primary_intf.INCOMING return USE_RED //primary_intf not in GADAG return USE_RED if F.LOWER return USE_RED if F.HIGHER return USE_BLUE //F unordered wrt S if F.topo_order > D_topo_order: return USE_BLUE else: return USE_RED Enyedi, et al. Expires August 19, 2016 [Page 37] Internet-Draft MRT FRR Algorithm February 2016 Select_Alternates(D, F, primary_intf) if not In_Common_Block(F, S) return PRIM_NH_IN_DIFFERENT_BLOCK if (D is F) or (D.order_proxy is F) return PRIM_NH_IS_D_OR_OP_FOR_D D_lower = D.order_proxy.LOWER D_higher = D.order_proxy.HIGHER D_topo_order = D.order_proxy.topo_order return Select_Alternates_Internal(D, F, primary_intf, D_lower, D_higher, D_topo_order) Figure 24: Select_Alternates() and Select_Alternates_Internal() It is useful to first handle the case where where F is also D, or F is the order proxy for D. In this case, only link protection is possible. The MRT that doesn't use the failed primary next-hop is used. If both MRTs use the primary next-hop, then the primary next- hop must be a cut-link, so either MRT could be used but the set of MRT next-hops must be pruned to avoid the failed primary next-hop interface. To indicate this case, Select_Alternates returns PRIM_NH_IS_D_OR_OP_FOR_D. Explicit pseudo-code to handle the three sub-cases above is not provided. The logic behind Select_Alternates_Internal is described in Figure 25. As an example, consider the first case described in the table, where the D>>S and D<>S and F<D.topo_order, then either F is ordered lower than D, or F is unordered with respect to D. Therefore, F is either on an increasing path from S to D, or it is on neither an increasing nor a decreasing path from S to D. In either case, it is safe to take a decreasing path from S to D to avoid F. We know that when S is R, the decreasing path is the red path, so it is safe to use the red path to avoid F. If F>>S or F<>S, we deduce that Enyedi, et al. Expires August 19, 2016 [Page 38] Internet-Draft MRT FRR Algorithm February 2016 F is on an increasing path from S to R. So in order to avoid F, we use a decreasing path from S to R, which is the red path. Instead, when F<>S | Blue path: | F>>S | additional | F on an | Use Red | | and | Increasing | only | criteria | increasing | to avoid | | D<>S | topo(F)>topo(D) | F on a | Use Blue | | S is | Blue path: | and | implies that | decreasing | to avoid | | R | Increasing | F<>D or F??D | path from | F | | | path to D. | F is | | S to D or | | | | Red path: | R | | neither | | | | Decreasing | +-----------------+------------+------------+ | | path to D. | | topo(F)>S | Blue path: | F<>S | topo(F)>topo(D) | F on | Use Blue | | | Decreasing | only | implies that | decreasing | to avoid | | | shortest | | F>>D or F??D | path from | F | | | path from | | | R to D | | | | S to R, | | | or | | | | then | | | neither | | | | decreasing | +-----------------+------------+------------+ | | shortest | | topo(F)>S | additional | F on Red | Use Blue | | | | and | criteria | | to avoid | | | | F<>S | additional | F on | Use Red | | only | Increasing | only | criteria | increasing | to avoid | | | shortest | | not needed | path from | F | | | path from | | | S to R | | | | S to R, +------+-----------------+------------+------------+ | | then | F<topo(D) | F on | Use Blue | | | increasing | only | implies that | decreasing | to avoid | | | shortest | | F>>D or F??D | path from | F | | | path from | | | R to D | | | | R to D. | | | or | | | | Red path: | | | neither | | | | Decreasing | +-----------------+------------+------------+ | | shortest | | topo(F)>S | additional | F on Blue | Use Red | Enyedi, et al. Expires August 19, 2016 [Page 40] Internet-Draft MRT FRR Algorithm February 2016 | | | and | criteria | | to avoid | | | | F<>S | additional | F on an | Use Blue | | | Red path: | only | criteria | increasing | to avoid | | | Incr. from | | not needed | path from | F | | | S to first | | | S to L | | | | node L>>D, | | | | | | | then decr. | | | | | | | +------+-----------------+------------+------------+ | | | F??S | F<-->S link is | | | | | | | MRT_INELIGIBLE | | | | | | +-----------------+------------+------------+ | | | | topo(F)>topo(D) | F on decr. | Use Blue | | | | | implies that | path from | to avoid | | | | | F>>D or F??D | L to D or | F | | | | | | neither | | | | | +-----------------+------------+------------+ | | | | topo(F)>S | GADAG link | F on an | Use Blue | | | | and | direction | incr. path | to avoid | | | | F<F | from S | F | | | | F is +-----------------+------------+------------+ | | | R | GADAG link | F on a | Use Red | | | | | direction | decr. path | to avoid | | | | | S<-F | from S | F | | | | +-----------------+------------+------------+ | | | | GADAG link | Either F is the order | | | | | direction | proxy for D (case | | | | | S<-->F | already handled) or D | Enyedi, et al. Expires August 19, 2016 [Page 41] Internet-Draft MRT FRR Algorithm February 2016 | | | | | is in a different block | | | | | | from F, in which case | | | | | | Red or Blue avoids F | | | | +-----------------+-------------------------+ | | | | S-F link not | Relies on special | | | | | in GADAG, | construction of GADAG | | | | | only when | to demonstrate that | | | | | S-F link is | using Red avoids F | | | | | MRT_INELIGIBLE | (see text) | +------+------------+------+-----------------+-------------------------+ Figure 25: determining MRT next-hops and alternates based on the partial order and topological sort relationships between the source(S), destination(D), primary next-hop(F), and block root(R). topo(N) indicates the topological sort value of node N. X??Y indicates that node X is unordered with respect to node Y. It is assumed that the case where F is D, or where F is the order proxy for D, has already been handled. The last case in Figure 25 requires additional explanation. The fact that the red path from S to D in this case avoids F relies on a special property of the GADAGs that we have constructed in this algorithm, a property not shared by all GADAGs in general. When D is unordered with respect to S, and F is the localroot for S, it can occur that the link between S and F is not in the GADAG only when that link has been marked MRT_INELIGIBLE. For an arbitrary GADAG, S doesn't have enough information based on the computed order relationships to determine if the red path or blue path will hit F (which is also the localroot) before hitting K or L, and making it safely to D. However, the GADAGs that we construct using the algorithm in this document are not arbitrary GADAGs. They have the additional property that incoming links to a localroot come from only one other node in the same block. This is a result of the method of construction. This additional property guarantees that the red path from S to D will never pass through the localroot of S. (That would require the localroot to play the role of L, the first node in the path ordered higher than D, which would in turn require the localroot to have two incoming links in the GADAG, which cannot happen.) Therefore it is safe to use the red path to avoid F with these specially constructed GADAGs. As an example of how Select_Alternates_Internal() operates, consider the ADAG depicted in Figure 26 and first suppose that G is the source, D is the destination and H is the failed next-hop. Since D>>G, we need to compare H.topo_order and D.topo_order. Since D.topo_order>H.topo_order, D must be either higher than H or unordered with respect to H, so we should select the decreasing path towards the root. If, however, the destination were instead J, we Enyedi, et al. Expires August 19, 2016 [Page 42] Internet-Draft MRT FRR Algorithm February 2016 must find that H.topo_order>J.topo_order, so we must choose the increasing Blue next-hop to J, which is I. In the case, when instead the destination is C, we find that we need to first decrease to avoid using H, so the Blue, first decreasing then increasing, path is selected. [E]<-[D]<-[H]<-[J] | ^ ^ ^ V | | | [R] [C] [G]->[I] | ^ ^ ^ V | | | [A]->[B]->[F]---| (a)ADAG rooted at R for a 2-connected graph Figure 26 5.9. Named Proxy-Nodes As discussed in Section 11.2 of [I-D.ietf-rtgwg-mrt-frr-architecture], it is necessary to find MRT- Blue and MRT-Red next-hops and MRT-FRR alternates for named proxy- nodes. An example use case is for a router that is not part of that local MRT Island, when there is only partial MRT support in the domain. 5.9.1. Determining Proxy-Node Attachment Routers Section 11.2 of [I-D.ietf-rtgwg-mrt-frr-architecture] discusses general considerations for determining the two proxy-node attachment routers for a given proxy-node, corresponding to a prefix. A router in the MRT Island that advertises the prefix is a candidate for being a proxy-node attachment router, with the associated named-proxy-cost equal to the advertised cost to the prefix. An Island Border Router (IBR) is a router in the MRT Island that is connected to an Island Neighbor(IN), which is a router not in the MRT Island but in the same area/level. An (IBR,IN) pair is a candidate for being a proxy-node attachment router, if the shortest path from the IN to the prefix does not enter the MRT Island. A method for identifying such loop-free Island Neighbors(LFINs) is given below. The named-proxy-cost assigned to each (IBR, IN) pair is cost(IBR, IN) + D_opt(IN, prefix). From the set of prefix-advertising routers and the set of IBRs with at least one LFIN, the two routers with the lowest named-proxy-cost Enyedi, et al. Expires August 19, 2016 [Page 43] Internet-Draft MRT FRR Algorithm February 2016 are selected. Ties are broken based upon the lowest Router ID. For ease of discussion, the two selected routers will be referred to as proxy-node attachment routers. 5.9.2. Computing if an Island Neighbor (IN) is loop-free As discussed above, the Island Neighbor needs to be loop-free with respect to the whole MRT Island for the destination. This can be accomplished by running the usual SPF algorithm while keeping track of which shortest paths have passed through the MRT island. Pseudo- code for this is shown in Figure 27. The Island_Marking_SPF() is run for each IN that needs to be evaluated for the loop-free condition, with the IN as the spf_root. Whether or not an IN is loop-free with respect to the MRT island can then be determined by evaluating node.PATH_HITS_ISLAND for each destination of interest. Enyedi, et al. Expires August 19, 2016 [Page 44] Internet-Draft MRT FRR Algorithm February 2016 Island_Marking_SPF(spf_root) Initialize spf_heap to empty Initialize nodes' spf_metric to infinity and next_hops to empty and PATH_HITS_ISLAND to false spf_root.spf_metric = 0 insert(spf_heap, spf_root) while (spf_heap is not empty) min_node = remove_lowest(spf_heap) foreach interface intf of min_node path_metric = min_node.spf_metric + intf.metric if path_metric < intf.remote_node.spf_metric intf.remote_node.spf_metric = path_metric if min_node is spf_root intf.remote_node.next_hops = make_list(intf) else intf.remote_node.next_hops = min_node.next_hops if intf.remote_node.IN_MRT_ISLAND intf.remote_node.PATH_HITS_ISLAND = true else intf.remote_node.PATH_HITS_ISLAND = min_node.PATH_HITS_ISLAND insert_or_update(spf_heap, intf.remote_node) else if path_metric == intf.remote_node.spf_metric if min_node is spf_root add_to_list(intf.remote_node.next_hops, intf) else add_list_to_list(intf.remote_node.next_hops, min_node.next_hops) if intf.remote_node.IN_MRT_ISLAND intf.remote_node.PATH_HITS_ISLAND = true else intf.remote_node.PATH_HITS_ISLAND = min_node.PATH_HITS_ISLAND Figure 27: Island_Marking_SPF for determining if an Island Neighbor is loop-free It is also possible that a given prefix is originated by a combination of non-island routers and island routers. The results of the Island_Marking_SPF computation can be used to determine if the shortest path from an IN to reach that prefix hits the MRT island. The shortest path for the IN to reach prefix P is determined by the total cost to reach prefix P, which is the sum of the cost for the IN to reach a prefix-advertising node and the cost with which that node advertises the prefix. The path with the minimum total cost to prefix P is chosen. If the prefix-advertising node for that minimum total cost path has PATH_HITS_ISLAND set to True, then the IN is not loop-free with respect to the MRT Island for reaching prefix P. If Enyedi, et al. Expires August 19, 2016 [Page 45] Internet-Draft MRT FRR Algorithm February 2016 there multiple minimum total cost paths to reach prefix P, then all of the prefix-advertising routers involved in the minimum total cost paths MUST have PATH_HITS_ISLAND set to False for the IN to be considered loop-free to reach P. Note that there are other computations that could be used to determine if paths from a given IN _might_ pass through the MRT Island for a given prefix or destination. For example, a previous version of this draft specified running the SPF algorithm on modified topology which treats the MRT island as a single node (with intra- island links set to zero cost) in order to provide input to computations to determine if the path from IN to non-island destination hits the MRT island in this modified topology. This computation is enough to guarantee that a path will not hit the MRT island in the original topology. However, it is possible that a path which is disqualified for hitting the MRT island in the modified topology will not actually hit the MRT Island in the original topology. The algorithm described in Island_Marking_SPF() above does not modify the original topology, and will only disqualify a path if the actual path does in fact hit the MRT island. Since all routers need to come to the same conclusion about which routers qualify as LFINs, this specification requires that all routers computing LFINs MUST use an algorithm whose result is identical to that of the Island_Marking_SPF() in Figure 27. 5.9.3. Computing MRT Next-Hops for Proxy-Nodes Determining the MRT next-hops for a proxy-node in the degenerate case where the proxy-node is attached to only one node in the GADAG is trivial, as all needed information can be derived from that proxy node attachment router. If there are multiple interfaces connecting the proxy node to the single proxy node attachment router, then some can be assigned to MRT-Red and others to MRT_Blue. Now, consider the proxy-node P that is attached to two proxy-node attachment routers. The pseudo-code for Select_Proxy_Node_NHs(P,S) in Figure 28 specifies how a computing-router S MUST compute the MRT red and blue next-hops to reach proxy-node P. The proxy-node attachment router with the lower value of mrt_node_id (as defined in Figure 15) is assigned to X, and the other proxy-node attachment router is assigned to Y. We will be using the relative order of X,Y, and S in the partial order defined by the GADAG to determine the MRT red and blue next-hops to reach P, so we also define A and B as the order proxies for X and Y, respectively, with respect to S. The order proxies for all nodes with respect to S were already computed in Compute_MRT_NextHops(). Enyedi, et al. Expires August 19, 2016 [Page 46] Internet-Draft MRT FRR Algorithm February 2016 def Select_Proxy_Node_NHs(P,S): if P.pnar1.node.node_id < P.pnar2.node.node_id: X = P.pnar1.node Y = P.pnar2.node else: X = P.pnar2.node Y = P.pnar1.node P.pnar_X = X P.pnar_Y = Y A = X.order_proxy B = Y.order_proxy if (A is S.localroot and B is S.localroot): // case 1.0 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if (A is S.localroot and B is not S.localroot): // case 2.0 if B.LOWER: // case 2.1 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if B.HIGHER: // case 2.2 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: // case 2.3 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if (A is not S.localroot and B is S.localroot): // case 3.0 if A.LOWER: // case 3.1 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if A.HIGHER: // case 3.2 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return Enyedi, et al. Expires August 19, 2016 [Page 47] Internet-Draft MRT FRR Algorithm February 2016 else: // case 3.3 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if (A is not S.localroot and B is not S.localroot): // case 4.0 if (S is A.localroot or S is B.localroot): // case 4.05 if A.topo_order < B.topo_order: // case 4.05.1 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: // case 4.05.2 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if A.LOWER: // case 4.1 if B.HIGHER: // case 4.1.1 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if B.LOWER: // case 4.1.2 if A.topo_order < B.topo_order: // case 4.1.2.1 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: // case 4.1.2.2 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: // case 4.1.3 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if A.HIGHER: // case 4.2 if B.HIGHER: // case 4.2.1 Enyedi, et al. Expires August 19, 2016 [Page 48] Internet-Draft MRT FRR Algorithm February 2016 if A.topo_order < B.topo_order: // case 4.2.1.1 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: // case 4.2.1.2 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if B.LOWER: // case 4.2.2 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: // case 4.2.3 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: // case 4.3 if B.LOWER: // case 4.3.1 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if B.HIGHER: // case 4.3.2 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: // case 4.3.3 if A.topo_order < B.topo_order: // case 4.3.3.1 Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: // case 4.3.3.2 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return assert(False) Figure 28: Select_Proxy_Node_NHs() Enyedi, et al. Expires August 19, 2016 [Page 49] Internet-Draft MRT FRR Algorithm February 2016 It is useful to understand up front that the blue next-hops to reach proxy-node P produced by Select_Proxy_Node_NHs() will always be the next-hops that reach proxy-node attachment router X, while the red next-hops to reach proxy-node P will always be the next-hops that reach proxy-node attachment router Y. This is different from the red and blue next-hops produced by Compute_MRT_NextHops() where, for example, blue next-hops to a destination that is ordered with respect to the source will always correspond to an INCREASING next-hop on the GADAG. The exact choice of which next-hops chosen by Select_Proxy_Node_NHs() as the blue next-hops to reach P (which will necessarily go through X on its way to P) does depend on the GADAG, but the relationship is more complex than was the case with Compute_MRT_NextHops(). There are twenty-one different relative order relationships between A, B and S that Select_Proxy_Node_NHs() uses to determine red and blue next-hops to P. This document does not attempt to provide an exhaustive description of each case considered in Select_Proxy_Node_NHs(). Instead we provide a high level overview of the different cases, and we consider a few cases in detail to give an example of the reasoning that can be used to understand each case. At the highest level, Select_Proxy_Node_NHs() distinguishes between four different cases depending on whether or not A or B is the localroot for S. For example, for case 4.0, neither A nor B is the localroot for S. Case 4.05 addresses the case where S is the localroot for either A or B, while cases 4.1, 4.2, and 4.3 address the cases where A is ordered lower than S, A is ordered higher than S, or A is unordered with respect to S on the GADAG. In general, each of these cases is then further subdivided into whether or not B is ordered lower than S, B is ordered higher than S, or B is unordered with respect to S. In some cases we also need a further level of discrimination, where we use the topological sort order of A with respect to B. As a detailed example, let's consider case 4.1 and all of its sub- cases, and explain why the red and blue next-hops to reach P are chosen as they are in Select_Proxy_Node_NHs(). In case 4.1, neither A nor B is the localroot for S, S is not the localroot for A or B, and A is ordered lower than S on the GADAG. In this situation, we know that the red path to reach X (as computed in Compute_MRT_NextHops()) will follow DECREASING next-hops towards A, while the blue path to reach X will follow INCREASING next-hops to the localroot, and then INCREASING next-hops to A. Now consider sub-case 4.1.1 where B is ordered higher than S. In this situation, we know that the blue path to reach Y will follow INCREASING next-hops towards B, while the red next-hops to reach Y Enyedi, et al. Expires August 19, 2016 [Page 50] Internet-Draft MRT FRR Algorithm February 2016 will follow DECREASING next-hops to the localroot, and then DECREASING next-hops to B. So to reach X and Y by two disjoint paths, we can choose the red next-hops to X and the blue next-hops to Y. We have chosen the convention that blue next-hops to P are those that pass through X, and red next-hops to P are those that pass through Y, so we can see that case 4.1.1 produces the desired result. Choosing blue to X and red to Y does not produce disjoint paths because the paths intersect at least at the localroot. Now consider sub-case 4.1.2 where B is ordered lower than S. In this situation, we know that the red path to reach Y will follow DECREASING next-hops towards B, while the BLUE next-hops to reach Y will follow INCREASING next-hops to the localroot, and then INCREASING next-hops to A. The choice here is more difficult than in 4.1.1 because A and B are both on the DECREASING path from S towards the localroot. We want to use the direct DECREASING(red) path to the one that is nearer to S on the GADAG. We get this extra information by comparing the topological sort order of A and B. If A.topo_orderB.topo_order, then we use red to X and blue to Y. Note that when A is unordered with respect to B, the result of comparing A.topo_order with B.topo_order could be greater than or less than. In this case, the result doesn't matter because either choice (red to Y and blue to X or red to X and blue to Y) would work. What is required is that all nodes in the network give the same result when comparing A.topo_order with B.topo_order. This is guarantee by having all nodes run the same algorithm (Run_Topological_Sort_GADAG()) to compute the topological sort order. Finally we consider case 4.1.3, where B is unordered with respect to S. In this case, the blue path to reach Y will follow the DECREASING next-hops towards the localroot until it reaches some node (K) which is ordered less than B, after which it will take INCREASING next-hops to B. The red path to reach Y will follow the INCREASING next-hops towards the localroot until it reaches some node (L) which is ordered greater than B, after which it will take DECREASING next-hops to B. Both K and A are reached by DECREASING from S, but we don't have information about whether or not that DECREASING path will hit K or A first. Instead, we do know that the INCREASING path from S will hit L before reaching A. Therefore, we use the red path to reach Y and the red path to reach X. Similar reasoning can be applied to understand the other seventeen cases used in Select_Proxy_Node_NHs(). However, cases 2.3 and 3.3 deserve special attention because the correctness of the solution for Enyedi, et al. Expires August 19, 2016 [Page 51] Internet-Draft MRT FRR Algorithm February 2016 these two cases relies on a special property of the GADAGs that we have constructed in this algorithm, a property not shared by all GADAGs in general. Focusing on case 2.3, we consider the case where A is the localroot for S, while B is not, and B is unordered with respect to S. The red path to X DECREASES from S to the localroot A, while the blue path to X INCREASES from S to the localroot A. The blue path to Y DECREASES towards the localroot A until it reaches some node (K) which is ordered less than B, after which the path INCREASES to B. The red path to Y INCREASES towards the localroot A until it reaches some node (L) which is ordered greater than B, after which the path DECREASES to B. It can be shown that for an arbitrary GADAG, with only the ordering relationships computed so far, we don't have enough information to choose a pair of paths to reach X and Y that are guaranteed to be disjoint. In some topologies, A will play the role of K, the first node ordered less than B on the blue path to Y. In other topologies, A will play the role of L, the first node ordered greater than B on the red path to Y. The basic problem is that we cannot distinguish between these two cases based on the ordering relationships. As discussed Section 5.8, the GADAGs that we construct using the algorithm in this document are not arbitrary GADAGs. They have the additional property that incoming links to a localroot come from only one other node in the same block. This is a result of the method of construction. This additional property guarantees that localroot A will never play the role of L in the red path to Y, since L must have at least two incoming links from different nodes in the same block in the GADAG. This in turn allows Select_Proxy_Node_NHs() to choose the red path to Y and the red path to X as the disjoint MRT paths to reach P. 5.9.4. Computing MRT Alternates for Proxy-Nodes After finding the red and the blue next-hops for a given proxy-node P, it is necessary to know which one of these to use in the case of failure. This can be done by Select_Alternates_Proxy_Node(), as shown in the pseudo-code in Figure 29. def Select_Alternates_Proxy_Node(P,F,primary_intf): S = primary_intf.local_node X = P.pnar_X Y = P.pnar_Y A = X.order_proxy B = Y.order_proxy if F is A and F is B: return 'PRIM_NH_IS_OP_FOR_BOTH_X_AND_Y' if F is A: return 'USE_RED' Enyedi, et al. Expires August 19, 2016 [Page 52] Internet-Draft MRT FRR Algorithm February 2016 if F is B: return 'USE_BLUE' if not In_Common_Block(A, B): if In_Common_Block(F, A): return 'USE_RED' elif In_Common_Block(F, B): return 'USE_BLUE' else: return 'USE_RED_OR_BLUE' if (not In_Common_Block(F, A) and not In_Common_Block(F, A) ): return 'USE_RED_OR_BLUE' alt_to_X = Select_Alternates(X, F, primary_intf) alt_to_Y = Select_Alternates(Y, F, primary_intf) if (alt_to_X == 'USE_RED_OR_BLUE' and alt_to_Y == 'USE_RED_OR_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED_OR_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED_OR_BLUE': return 'USE_RED' if (A is S.localroot and B is S.localroot): // case 1.0 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if (A is S.localroot and B is not S.localroot): // case 2.0 if B.LOWER: // case 2.1 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if B.HIGHER: Enyedi, et al. Expires August 19, 2016 [Page 53] Internet-Draft MRT FRR Algorithm February 2016 // case 2.2 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) else: // case 2.3 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if (A is not S.localroot and B is S.localroot): // case 3.0 if A.LOWER: // case 3.1 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if A.HIGHER: // case 3.2 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: // case 3.3 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if (A is not S.localroot Enyedi, et al. Expires August 19, 2016 [Page 54] Internet-Draft MRT FRR Algorithm February 2016 and B is not S.localroot): // case 4.0 if (S is A.localroot or S is B.localroot): // case 4.05 if A.topo_order < B.topo_order: // case 4.05.1 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: // case 4.05.2 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if A.LOWER: // case 4.1 if B.HIGHER: // case 4.1.1 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if B.LOWER: // case 4.1.2 if A.topo_order < B.topo_order: // case 4.1.2.1 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: // case 4.1.2.2 if (alt_to_X == 'USE_RED' Enyedi, et al. Expires August 19, 2016 [Page 55] Internet-Draft MRT FRR Algorithm February 2016 and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) else: // case 4.1.3 if (F.LOWER and not F.HIGHER and F.topo_order > A.topo_order): // case 4.1.3.1 return 'USE_RED' else: // case 4.1.3.2 return 'USE_BLUE' if A.HIGHER: // case 4.2 if B.HIGHER: // case 4.2.1 if A.topo_order < B.topo_order: // case 4.2.1.1 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: // case 4.2.1.2 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if B.LOWER: // case 4.2.2 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': Enyedi, et al. Expires August 19, 2016 [Page 56] Internet-Draft MRT FRR Algorithm February 2016 return 'USE_RED' assert(False) else: // case 4.2.3 if (F.HIGHER and not F.LOWER and F.topo_order < A.topo_order): return 'USE_RED' else: return 'USE_BLUE' else: // case 4.3 if B.LOWER: // case 4.3.1 if (F.LOWER and not F.HIGHER and F.topo_order > B.topo_order): return 'USE_BLUE' else: return 'USE_RED' if B.HIGHER: // case 4.3.2 if (F.HIGHER and not F.LOWER and F.topo_order < B.topo_order): return 'USE_BLUE' else: return 'USE_RED' else: // case 4.3.3 if A.topo_order < B.topo_order: // case 4.3.3.1 if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: // case 4.3.3.2 if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) assert(False) Enyedi, et al. Expires August 19, 2016 [Page 57] Internet-Draft MRT FRR Algorithm February 2016 Figure 29: Select_Alternates_Proxy_Node() Select_Alternates_Proxy_Node(P,F,primary_intf) determines whether it is safe to use the blue path to P (which goes through X), the red path to P (which goes through Y), or either, when the primary_intf to node F (and possibly node F) fails. The basic approach is to run Select_Alternates(X,F,primary_intf) and Select_Alternates(Y,F,primary_intf) to determine which of the two MRT paths to X and which of the two MRT paths to Y is safe to use in the event of the failure of F. In general, we will find that if it is safe to use a particular path to X or Y when F fails, and Select_Proxy_Node_NHs() used that path when constructing the red or blue path to reach P, then it will also be safe to use that path to reach P when F fails. This rule has one exception which is covered below. First, we give a concrete example of how Select_Alternates_Proxy_Node() works in the common case. The twenty one ordering relationships used in Select_Proxy_Node_NHs() are repeated in Select_Alternates_Proxy_Node(). We focus on case 4.1.1 to give give a detailed example of the reasoning used in Select_Alternates_Proxy_Node(). In Select_Proxy_Node_NHs(), we determined for case 4.1.1 that the red next-hops to X and the blue next-hops to Y allow us to reach X and Y by disjoint paths, and are thus the blue and red next-hops to reach P. Therefore, if we run Select_Alternates(X, F, primary_intf) and we find that it is safe to USE_RED to reach X, then we also conclude that it is safe to use the MRT path through X to reach P (the blue path to P) when F fails. Similarly, if run Select_Alternates(X, F, primary_intf) and we find that it is safe to USE_BLUE to reach Y, then we also conclude that it is safe to use the MRT path through Y to reach P (the red path to P) when F fails. If both of the paths that were used in Select_Proxy_Node_NHs() to construct the blue and red paths to P are found to be safe to use to use to reach X and Y, t then we conclude that we can use either the red or the blue path to P. This simple reasoning gives the correct answer in most of the cases. However, additional logic is needed when either A or B (but not both A and B) is unordered with respect to S. This applies to cases 4.1.3, 4.2.3, 4.3.1, and 4.3.2. Looking at case 4.1.3 in more detail, A is ordered less than S, but B is unordered with respect to S. In the discussion of case 4.1.3 above, we saw that Select_Proxy_Node_NHs() chose the red path to reach Y and the red path to reach X. We also saw that the red path to reach Y will follow the INCREASING next-hops towards the localroot until it reaches some node (L) which is ordered greater than B, after which it will take DECREASING next-hops to B. The problem is that the red path to reach P (the one that goes through Y) won't necessarily be the same as the red path to reach Y. This is because the next-hop Enyedi, et al. Expires August 19, 2016 [Page 58] Internet-Draft MRT FRR Algorithm February 2016 that node L computes for its red next-hop to reach P may be different from the next-hop it computes for its red next-hop to reach Y. This is because B is ordered lower than L, so L applies case 4.1.2 of Select_Proxy_Node_NHs() in order to determine its next-hops to reach P. If A.topo_orderB.topo_order (case 4.1.2.2), then L will choose INCREASING next-hops to reach B, which is different from what L computes in Compute_MRT_NextHops() to reach Y. So testing the safety of the path for S to reach Y on failure of F as a surrogate for the safety of using the red path to reach P is not reliable in this case. It is possible construct topologies where the red path to P hits F even though the red path to Y does not hit F. Fortunately there is enough information in the order relationships that we have already computed to still figure out which alternate to choose in these four cases. The basic idea is to always choose the path involving the ordered node, unless that path would hit F. Returning to case 4.1.3, we see that since A is ordered lower than S, the only way for S to hit F using a simple DECREASING path to A is for F to lie between A and S on the GADAG. This scenario is covered by requiring that F be lower than S (but not also higher than S) and that F.topo_order>A.topo_order in case 4.1.3.1. We just need to confirm that it is safe to use the path involving B in this scenario. In case 4.1.3.1, either F is between A and S on the GADAG, or F is unordered with respect to A and lies on the DECREASING path from S to the localroot. When F is between A and S on the GADAG, then the path through B chosen to avoid A in Select_Proxy_Node_NHs() will also avoid F. When F is unordered with respect to A and lies on the DECREASING path from S to the localroot, then we consider two cases. Either F.topo_orderB.topo_order. In the first case, since F.topo_orderA.topo_order, it must be the case that A.topo_orderB.topo_order, the only way for the path involving B to hit F is if it DECREASES from L to B through F , ie. it must be that L>>F>>B. However, since S>>F, this would imply that S>>B. However, we know that S is unordered with respect to B, so the second case cannot occur. So we have demonstrated that the red path to P (which goes via B and Y) is safe to use under the conditions of 4.1.3.1. Similar reasoning can be applied to the other three special cases where either A or B is unordered with respect to S. Enyedi, et al. Expires August 19, 2016 [Page 59] Internet-Draft MRT FRR Algorithm February 2016 6. MRT Lowpoint Algorithm: Next-hop conformance This specification defines the MRT Lowpoint Algorithm, which include the construction of a common GADAG and the computation of MRT-Red and MRT-Blue next-hops to each node in the graph. An implementation MAY select any subset of next-hops for MRT-Red and MRT-Blue that respect the available nodes that are described in Section 5.7 for each of the MRT-Red and MRT-Blue and the selected next-hops are further along in the interval of allowed nodes towards the destination. For example, the MRT-Blue next-hops used when the destination Y >> X, the computing router, MUST be one or more nodes, T, whose topo_order is in the interval [X.topo_order, Y.topo_order] and where Y >> T or Y is T. Similarly, the MRT-Red next-hops MUST be have a topo_order in the interval [R-small.topo_order, X.topo_order] or [Y.topo_order, R-big.topo_order]. Implementations SHOULD implement the Select_Alternates() function to pick an MRT-FRR alternate. 7. Broadcast interfaces When broadcast interfaces are used to connect nodes, the broadcast network MUST be represented as a pseudonode, where each real node connects to the pseudonode. The interface metric in the direction from real node to pseudonode is the non-zero interface metric, while the interface metric in the direction from the pseudonode to the real node is set to zero. This is consistent with the way that broadcast interfaces are represented as pseudonodes in IS-IS and OSPF. Pseudonodes MUST be treated as equivalent to real nodes in the network graph used in the MRT algorithm with a few exceptions detailed below. The pseudonodes MUST be included in the computation of the GADAG. The neighbors of the pseudonode need to know the mrt_node_id of the pseudonode in order to consistently order interfaces, which is needed to compute the GADAG. The mrt_node_id for IS-IS is the 7 octet neighbor system ID and pseudonode number in TLV #22 or TLV#222. The mrt_node_id for OSPFv2 is the 4 octet interface address of the Designated Router found in the Link ID field for the link type 2 (transit network) in the Router-LSA. The mrt_node_id for OSPFv3 is the 4 octet interface address of the Designated Router found in the Neighbor Interface ID field for the link type 2 (transit network) in the Router-LSA. pseudonodes MUST NOT be considered as candidates for GADAG root selection. Note that this is different from the Neighbor Router ID field used for the mrt_node_id for point-to-point links in OSPFv3 Router-LSAs given in Figure 15. Enyedi, et al. Expires August 19, 2016 [Page 60] Internet-Draft MRT FRR Algorithm February 2016 Pseudonodes MUST NOT be considered as candidates for selection as GADAG root. This rule is intended to result in a more stable network- wide selection of GADAG root by removing the possibility that the change of Designated Router or Designated Intermediate System on a broadcast network can result in a change of GADAG root. 7.1. Computing MRT next-hops on broadcast networks The pseudonode does not correspond to an real node, so it is not actually involved in forwarding. A real node on a broadcast network cannot simply forward traffic to the broadcast network. It must specify another real node on the broadcast network as the next-hop. On a network graph where a broadcast network is represented by a pseudonode, this means that if a real node determines that the next- hop to reach a given destination is a pseudonode, it must also determine the next-next-hop for that destination in the network graph, which corresponds to a real node attached to the broadcast network. It is interesting to note that this issue is not unique to the MRT algorithm, but is also encountered in normal SPF computations for IGPs. Section 16.1.1 of [RFC2328] describes how this is done for OSPF. As OSPF runs Dijkstra's algorithm, whenever a shorter path is found reach a real destination node, and the shorter path is one hop from the computing routing, and that one hop is a pseudonode, then the next-hop for that destination is taken from the interface IP address in the Router-LSA correspond to the link to the real destination node For IS-IS, in the example pseudo-code implementation of Dijkstra's algorithm in Annex C of [ISO10589-Second-Edition] whenever the algorithm encounters an adjacency from a real node to a pseudonode, it gets converted to a set of adjacencies from the real node to the neighbors of the pseudonode. In this way, the computed next-hops point all the way to the real node, and not the pseudonode. We could avoid the problem of determining next-hops across pseudonodes in MRT by converting the pseudonode representation of broadcast networks to a full mesh of links between real nodes on the same network. However, if we make that conversion before computing the GADAG, we lose information about which links actually correspond to a single physical interface into the broadcast network. This could result computing red and blue next-hops that use the same broadcast interface, in which case neither the red nor the blue next- hop would be usable as an alternate on failure of the broadcast interface. Enyedi, et al. Expires August 19, 2016 [Page 61] Internet-Draft MRT FRR Algorithm February 2016 Instead, we take the following approach, which maintains the property that either the red and blue next-hop will avoid the broadcast network, if topologically allowed. We run the MRT algorithm treating the pseudonodes as equivalent to real nodes in the network graph, with the exceptions noted above. In addition to running the MRT algorithm from the point of view of itself, a computing router connected to a pseudonode MUST also run the MRT algorithm from the point of view of each of its pseudonode neighbors. For example, if a computing router S determines that its MRT red next-hop to reach a destination D is a pseudonode P, S looks at its MRT algorithm computation from P's point of view to determine P's red next-hop to reach D, say interface 1 on node X. S now knows that its real red next-hop to reach D is interface 1 on node X on the broadcast network represented by P, and can install the corresponding entry in its FIB. 7.2. Using MRT next-hops as alternates in the event of failures on broadcast networks In the previous section, we specified how to compute MRT next-hops when broadcast networks are involved. In this section, we discuss how a PLR can use those MRT next-hops in the event of failures involving broadcast networks. A PLR attached to a broadcast network running only OSPF or IS-IS with large Hello intervals has limited ability to quickly detect failures on a broadcast network. The only failure mode that can be quickly detected is the failure of the physical interface connecting the PLR to the broadcast network. For the failure of the interface connecting the PLR to the broadcast network, the alternate that avoids the broadcast network can be computed by using the broadcast network pseudonode as F, the primary next-hop node, in Select_Alternates(). This will choose an alternate path that avoids the broadcast network. However, the alternate path will not necessarily avoid all of the real nodes connected to the broadcast network. This is because we have used the pseudonode to represent the broadcast network. And we have enforced the node-protecting property of MRT on the pseudonode to provide protection against failure of the broadcast network, not the real next-hop nodes on the broadcast network. This is the best that we can hope to do if failure of the broadcast interface is the only failure mode that the PLR can respond to. We can improve on this if the PLR also has the ability to quickly detect a lack of connectivity across the broadcast network to a given IP-layer node. This can be accomplished by running BFD between all pairs of IGP neighbors on the broadcast network. Note that in the case of OSPF, this would require establishing BFD sessions between all pairs of neighbors in the 2-WAY state. When the PLR can quickly Enyedi, et al. Expires August 19, 2016 [Page 62] Internet-Draft MRT FRR Algorithm February 2016 detect the failure of a particular next-hop across a broadcast network, then the PLR can be more selective in its choice of alternates. For example, when the PLR observes that connectivity to an IP-layer node on a broadcast network has failed, the PLR may choose to still use the broadcast network to reach other IP-layer nodes which are still reachable. Or if the PLR observes that connectivity has failed to several IP-layer nodes on the same broadcast network, it may choose to treat the entire broadcast network as failed. The choice of MRT alternates by a PLR for a particular set of failure conditions is a local decision, since it does not require coordination with other nodes. 8. Evaluation of Alternative Methods for Constructing GADAGs This document specifies the MRT Lowpoint algorithm. One component of the algorithm involves constructing a common GADAG based on the network topology. The MRT Lowpoint algorithm computes the GADAG using the method described in Section 5.5. This method aims to minimize the amount of computation required to compute the GADAG. In the process of developing the MRT Lowpoint algorithm, two alternative methods for constructing GADAGs were also considered. These alternative methods are described in Appendix B and Appendix C. In general, these other two methods require more computation to compute the GADAG. The analysis below was performed to determine if the alternative GADAG construction methods produce shorter MRT alternate paths in real network topologies, and if so, to what extent. Figure 30 compares results obtained using the three different methods for constructing GADAGs on five different service provider network topologies. MRT_LOWPOINT indicates the method specified in Section 5.5, while MRT_SPF and MRT_HYBRID indicate the methods specified in Appendix B and Appendix C, respectively. The columns on the right present the distribution of alternate path lengths for each GADAG construction method. Each MRT computation was performed using a same GADAG root chosen based on centrality. For three of the topologies analyzed (T201, T206, and T211), the use of MRT_SPF or MRT_HYBRID methods does not appear to provide a significantly shorter alternate path lengths compared to the MRT_LOWPOINT method. However, for two of the topologies (T216 and T219), the use of the MRT_SPF method resulted in noticeably shorter alternate path lengths than the use of the MRT_LOWPOINT or MRT_HYBRID methods. It was decided to use the MRT_LOWPOINT method to construct the GADAG in the algorithm specified in this draft, in order to initially offer an algorithm with lower computational requirements. These results indicate that in the future it may be useful to evaluate and Enyedi, et al. Expires August 19, 2016 [Page 63] Internet-Draft MRT FRR Algorithm February 2016 potentially specify other MRT algorithm variants that use different GADAG construction methods. +-------------------------------------------------------------------+ | Topology name | percentage of failure scenarios | | | protected by an alternate N hops | | GADAG construction | longer than the primary path | | method +------------------------------------+ | | | | | | | | | | no | | | | | | | |10 |12 |14 | alt| | |0-1|2-3|4-5|6-7|8-9|-11|-13|-15| <16| +------------------------------+---+---+---+---+---+---+---+---+----+ | T201(avg primary hops=3.5) | | | | | | | | | | | MRT_HYBRID | 33| 26| 23| 6| 3| | | | | | MRT_SPF | 33| 36| 23| 6| 3| | | | | | MRT_LOWPOINT | 33| 36| 23| 6| 3| | | | | +------------------------------+---+---+---+---+---+---+---+---+----+ | T206(avg primary hops=3.7) | | | | | | | | | | | MRT_HYBRID | 50| 35| 13| 2| | | | | | | MRT_SPF | 50| 35| 13| 2| | | | | | | MRT_LOWPOINT | 55| 32| 13| | | | | | | +------------------------------+---+---+---+---+---+---+---+---+----+ | T211(avg primary hops=3.3) | | | | | | | | | | | MRT_HYBRID | 86| 14| | | | | | | | | MRT_SPF | 86| 14| | | | | | | | | MRT_LOWPOINT | 85| 15| 1| | | | | | | +------------------------------+---+---+---+---+---+---+---+---+----+ | T216(avg primary hops=5.2) | | | | | | | | | | | MRT_HYBRID | 23| 22| 18| 13| 10| 7| 4| 2| 2| | MRT_SPF | 35| 32| 19| 9| 3| 1| | | | | MRT_LOWPOINT | 28| 25| 18| 11| 7| 6| 3| 2| 1| +------------------------------+---+---+---+---+---+---+---+---+----+ | T219(avg primary hops=7.7) | | | | | | | | | | | MRT_HYBRID | 20| 16| 13| 10| 7| 5| 5| 5| 3| | MRT_SPF | 31| 23| 19| 12| 7| 4| 2| 1| | | MRT_LOWPOINT | 19| 14| 15| 12| 10| 8| 7| 6| 10| +------------------------------+---+---+---+---+---+---+---+---+----+ Figure 30 9. Implementation Status [RFC Editor: please remove this section prior to publication.] Please see [I-D.ietf-rtgwg-mrt-frr-architecture] for details on implementation status. Enyedi, et al. Expires August 19, 2016 [Page 64] Internet-Draft MRT FRR Algorithm February 2016 10. Operational Considerations This sections discusses operational considerations related to the the MRT Lowpoint algorithm and other potential MRT algorithm variants. For a discussion of operational considerations related to MRT-FRR in general, see the Operational Considerations section of [I-D.ietf-rtgwg-mrt-frr-architecture]. 10.1. GADAG Root Selection The Default MRT Profile uses the GADAG Root Selection Priority advertised by routers as the primary criterion for selecting the GADAG root. It is RECOMMENDED that an operator designate a set of routers as good choices for selection as GADAG root by setting the GADAG Root Selection Priority for that set of routers to lower (more preferred) numerical values. Criteria for making this designation are discussed below. Analysis has shown that the centrality of a router can have a significant impact on the lengths of the alternate paths computed. Therefore, it is RECOMMENDED that off-line analysis that considers the centrality of a router be used to help determine how good a choice a particular router is for the role of GADAG root. If the router currently selected as GADAG root becomes unreachable in the IGP topology, then a new GADAG root will be selected. Changing the GADAG root can change the overall structure of the GADAG as well the paths of the red and blue MRT trees built using that GADAG. In order to minimize change in the associated red and blue MRT forwarding entries that can result from changing the GADAG root, it is RECOMMENDED that operators prioritize for selection as GADAG root those routers that are expected to consistently remain part of the IGP topology. 10.2. Destination-rooted GADAGs The MRT Lowpoint algorithm constructs a single GADAG rooted at a single node selected as the GADAG root. It is also possible to construct a different GADAG for each destination, with the GADAG rooted at the destination. A router can compute the MRT-Red and MRT- Blue next-hops for that destination based on the GADAG rooted at that destination. Building a different GADAG for each destination is computationally more expensive, but it may give somewhat shorter alternate paths. Using destination-rooted GADAGs would require a new MRT profile to be created with a new MRT algorithm specification, since all routers in the MRT Island would need to use destination- rooted GADAGs. Enyedi, et al. Expires August 19, 2016 [Page 65] Internet-Draft MRT FRR Algorithm February 2016 11. Acknowledgements The authors would like to thank Shraddha Hegde, Eric Wu, Janos Farkas, Stewart Bryant, and Alvaro Retana for their suggestions and review. We would also like to thank Anil Kumar SN for his assistance in clarifying the algorithm description and pseudo-code. 12. IANA Considerations This document includes no request to IANA. 13. Security Considerations The algorithm described in this document does not introduce new security concerns beyond those already discussed in the document describing the MRT FRR architecture [I-D.ietf-rtgwg-mrt-frr-architecture]. 14. References 14.1. Normative References [I-D.ietf-rtgwg-mrt-frr-architecture] Atlas, A., Kebler, R., Bowers, C., Envedi, G., Csaszar, A., Tantsura, J., and R. White, "An Architecture for IP/ LDP Fast-Reroute Using Maximally Redundant Trees", draft- ietf-rtgwg-mrt-frr-architecture-07 (work in progress), October 2015. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . 14.2. Informative References [EnyediThesis] Enyedi, G., "Novel Algorithms for IP Fast Reroute", Department of Telecommunications and Media Informatics, Budapest University of Technology and Economics Ph.D. Thesis, February 2011, . Enyedi, et al. Expires August 19, 2016 [Page 66] Internet-Draft MRT FRR Algorithm February 2016 [IEEE8021Qca] IEEE 802.1, "IEEE 802.1Qca Bridges and Bridged Networks - Amendment: Path Control and Reservation - Draft 2.1", (work in progress), June 24, 2015, . [ISO10589-Second-Edition] International Organization for Standardization, "Intermediate system to Intermediate system intra-domain routeing information exchange protocol for use in conjunction with the protocol for providing the connectionless-mode Network Service (ISO 8473)", ISO/ IEC 10589:2002, Second Edition, Nov. 2002. [Kahn_1962_topo_sort] Kahn, A., "Topological sorting of large networks", Communications of the ACM, Volume 5, Issue 11 , Nov 1962, . [MRTLinear] Enyedi, G., Retvari, G., and A. Csaszar, "On Finding Maximally Redundant Trees in Strictly Linear Time", IEEE Symposium on Computers and Comunications (ISCC) , 2009, . [RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, DOI 10.17487/RFC2328, April 1998, . [RFC5120] Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi Topology (MT) Routing in Intermediate System to Intermediate Systems (IS-ISs)", RFC 5120, DOI 10.17487/RFC5120, February 2008, . [RFC7490] Bryant, S., Filsfils, C., Previdi, S., Shand, M., and N. So, "Remote Loop-Free Alternate (LFA) Fast Reroute (FRR)", RFC 7490, DOI 10.17487/RFC7490, April 2015, . Appendix A. Python Implementation of MRT Lowpoint Algorithm Below is Python code implementing the MRT Lowpoint algorithm specified in this document. In order to avoid the page breaks in the .txt version of the draft, one can cut and paste the Python code from the .xml version. The code is also posted on Github. Enyedi, et al. Expires August 19, 2016 [Page 67] Internet-Draft MRT FRR Algorithm February 2016 While this Python code is believed to correctly implement the pseudo- code description of the algorithm, in the event of a difference, the pseudo-code description should be considered normative. # This program has been tested to run on Python 2.6 and 2.7 # (specifically Python 2.6.6 and 2.7.8 were tested). # The program has known incompatibilities with Python 3.X. # When executed, this program will generate a text file describing # an example topology. It then reads that text file back in as input # to create the example topology, and runs the MRT algorithm.This # was done to simplify the inclusion of the program as a single text # file that can be extracted from the IETF draft. # The output of the program is four text files containing a description # of the GADAG, the blue and red MRTs for all destinations, and the # MRT alternates for all failures. import random import os.path import heapq # simple Class definitions allow structure-like dot notation for # variables and a convenient place to initialize those variables. class Topology: def __init__(self): self.gadag_root = None self.node_list = [] self.node_dict = {} self.test_gr = None self.island_node_list_for_test_gr = [] self.stored_named_proxy_dict = {} self.init_new_computing_router() def init_new_computing_router(self): self.island_node_list = [] self.named_proxy_dict = {} class Node: def __init__(self): self.node_id = None self.intf_list = [] self.profile_id_list = [0] self.GR_sel_priority = 128 self.blue_next_hops_dict = {} self.red_next_hops_dict = {} self.blue_to_green_nh_dict = {} self.red_to_green_nh_dict = {} Enyedi, et al. Expires August 19, 2016 [Page 68] Internet-Draft MRT FRR Algorithm February 2016 self.prefix_cost_dict = {} self.pnh_dict = {} self.alt_dict = {} self.init_new_computing_router() def init_new_computing_router(self): self.island_intf_list = [] self.IN_MRT_ISLAND = False self.IN_GADAG = False self.dfs_number = None self.dfs_parent = None self.dfs_parent_intf = None self.dfs_child_list = [] self.lowpoint_number = None self.lowpoint_parent = None self.lowpoint_parent_intf = None self.localroot = None self.block_id = None self.IS_CUT_VERTEX = False self.blue_next_hops = [] self.red_next_hops = [] self.primary_next_hops = [] self.alt_list = [] class Interface: def __init__(self): self.metric = None self.area = None self.MRT_INELIGIBLE = False self.IGP_EXCLUDED = False self.SIMULATION_OUTGOING = False self.init_new_computing_router() def init_new_computing_router(self): self.UNDIRECTED = True self.INCOMING = False self.OUTGOING = False self.INCOMING_STORED = False self.OUTGOING_STORED = False self.IN_MRT_ISLAND = False self.PROCESSED = False class Bundle: def __init__(self): self.UNDIRECTED = True self.OUTGOING = False self.INCOMING = False class Alternate: def __init__(self): Enyedi, et al. Expires August 19, 2016 [Page 69] Internet-Draft MRT FRR Algorithm February 2016 self.failed_intf = None self.red_or_blue = None self.nh_list = [] self.fec = 'NO_ALTERNATE' self.prot = 'NO_PROTECTION' self.info = 'NONE' class Proxy_Node_Attachment_Router: def __init__(self): self.prefix = None self.node = None self.named_proxy_cost = None self.min_lfin = None self.nh_intf_list = [] class Named_Proxy_Node: def __init__(self): self.node_id = None #this is the prefix_id self.node_prefix_cost_list = [] self.lfin_list = [] self.pnar1 = None self.pnar2 = None self.pnar_X = None self.pnar_Y = None self.blue_next_hops = [] self.red_next_hops = [] self.primary_next_hops = [] self.blue_next_hops_dict = {} self.red_next_hops_dict = {} self.pnh_dict = {} self.alt_dict = {} def Interface_Compare(intf_a, intf_b): if intf_a.metric < intf_b.metric: return -1 if intf_b.metric < intf_a.metric: return 1 if intf_a.remote_node.node_id < intf_b.remote_node.node_id: return -1 if intf_b.remote_node.node_id < intf_a.remote_node.node_id: return 1 return 0 def Sort_Interfaces(topo): for node in topo.island_node_list: node.island_intf_list.sort(Interface_Compare) def Reset_Computed_Node_and_Intf_Values(topo): Enyedi, et al. Expires August 19, 2016 [Page 70] Internet-Draft MRT FRR Algorithm February 2016 topo.init_new_computing_router() for node in topo.node_list: node.init_new_computing_router() for intf in node.intf_list: intf.init_new_computing_router() # This function takes a file with links represented by 2-digit # numbers in the format: # 01,05,10 # 05,02,30 # 02,01,15 # which represents a triangle topology with nodes 01, 05, and 02 # and symmetric metrics of 10, 30, and 15. # Inclusion of a fourth column makes the metrics for the link # asymmetric. An entry of: # 02,07,10,15 # creates a link from node 02 to 07 with metrics 10 and 15. def Create_Topology_From_File(filename): topo = Topology() node_id_set= set() cols_list = [] # on first pass just create nodes with open(filename + '.csv') as topo_file: for line in topo_file: line = line.rstrip('\r\n') cols=line.split(',') cols_list.append(cols) nodea_node_id = int(cols[0]) nodeb_node_id = int(cols[1]) if (nodea_node_id > 999 or nodeb_node_id > 999): print("node_id must be between 0 and 999.") print("exiting.") exit() node_id_set.add(nodea_node_id) node_id_set.add(nodeb_node_id) for node_id in node_id_set: node = Node() node.node_id = node_id topo.node_list.append(node) topo.node_dict[node_id] = node # on second pass create interfaces for cols in cols_list: nodea_node_id = int(cols[0]) nodeb_node_id = int(cols[1]) metric = int(cols[2]) reverse_metric = int(cols[2]) if len(cols) > 3: Enyedi, et al. Expires August 19, 2016 [Page 71] Internet-Draft MRT FRR Algorithm February 2016 reverse_metric=int(cols[3]) nodea = topo.node_dict[nodea_node_id] nodeb = topo.node_dict[nodeb_node_id] nodea_intf = Interface() nodea_intf.metric = metric nodea_intf.area = 0 nodeb_intf = Interface() nodeb_intf.metric = reverse_metric nodeb_intf.area = 0 nodea_intf.remote_intf = nodeb_intf nodeb_intf.remote_intf = nodea_intf nodea_intf.remote_node = nodeb nodeb_intf.remote_node = nodea nodea_intf.local_node = nodea nodeb_intf.local_node = nodeb nodea_intf.link_data = len(nodea.intf_list) nodeb_intf.link_data = len(nodeb.intf_list) nodea.intf_list.append(nodea_intf) nodeb.intf_list.append(nodeb_intf) return topo def MRT_Island_Identification(topo, computing_rtr, profile_id, area): if profile_id in computing_rtr.profile_id_list: computing_rtr.IN_MRT_ISLAND = True explore_list = [computing_rtr] else: return while explore_list != []: next_rtr = explore_list.pop() for intf in next_rtr.intf_list: if ( (not intf.MRT_INELIGIBLE) and (not intf.remote_intf.MRT_INELIGIBLE) and (not intf.IGP_EXCLUDED) and intf.area == area and (profile_id in intf.remote_node.profile_id_list)): intf.IN_MRT_ISLAND = True intf.remote_intf.IN_MRT_ISLAND = True if (not intf.remote_node.IN_MRT_ISLAND): intf.remote_node.IN_MRT_ISLAND = True explore_list.append(intf.remote_node) def Compute_Island_Node_List_For_Test_GR(topo, test_gr): Reset_Computed_Node_and_Intf_Values(topo) topo.test_gr = topo.node_dict[test_gr] MRT_Island_Identification(topo, topo.test_gr, 0, 0) for node in topo.node_list: if node.IN_MRT_ISLAND: topo.island_node_list_for_test_gr.append(node) Enyedi, et al. Expires August 19, 2016 [Page 72] Internet-Draft MRT FRR Algorithm February 2016 def Set_Island_Intf_and_Node_Lists(topo): for node in topo.node_list: if node.IN_MRT_ISLAND: topo.island_node_list.append(node) for intf in node.intf_list: if intf.IN_MRT_ISLAND: node.island_intf_list.append(intf) global_dfs_number = None def Lowpoint_Visit(x, parent, intf_p_to_x): global global_dfs_number x.dfs_number = global_dfs_number x.lowpoint_number = x.dfs_number global_dfs_number += 1 x.dfs_parent = parent if intf_p_to_x == None: x.dfs_parent_intf = None else: x.dfs_parent_intf = intf_p_to_x.remote_intf x.lowpoint_parent = None if parent != None: parent.dfs_child_list.append(x) for intf in x.island_intf_list: if intf.remote_node.dfs_number == None: Lowpoint_Visit(intf.remote_node, x, intf) if intf.remote_node.lowpoint_number < x.lowpoint_number: x.lowpoint_number = intf.remote_node.lowpoint_number x.lowpoint_parent = intf.remote_node x.lowpoint_parent_intf = intf else: if intf.remote_node is not parent: if intf.remote_node.dfs_number < x.lowpoint_number: x.lowpoint_number = intf.remote_node.dfs_number x.lowpoint_parent = intf.remote_node x.lowpoint_parent_intf = intf def Run_Lowpoint(topo): global global_dfs_number global_dfs_number = 0 Lowpoint_Visit(topo.gadag_root, None, None) max_block_id = None def Assign_Block_ID(x, cur_block_id): global max_block_id x.block_id = cur_block_id for c in x.dfs_child_list: Enyedi, et al. Expires August 19, 2016 [Page 73] Internet-Draft MRT FRR Algorithm February 2016 if (c.localroot is x): max_block_id += 1 Assign_Block_ID(c, max_block_id) else: Assign_Block_ID(c, cur_block_id) def Run_Assign_Block_ID(topo): global max_block_id max_block_id = 0 Assign_Block_ID(topo.gadag_root, max_block_id) def Construct_Ear(x, stack, intf, ear_type): ear_list = [] cur_intf = intf not_done = True while not_done: cur_intf.UNDIRECTED = False cur_intf.OUTGOING = True cur_intf.remote_intf.UNDIRECTED = False cur_intf.remote_intf.INCOMING = True if cur_intf.remote_node.IN_GADAG == False: cur_intf.remote_node.IN_GADAG = True ear_list.append(cur_intf.remote_node) if ear_type == 'CHILD': cur_intf = cur_intf.remote_node.lowpoint_parent_intf else: assert ear_type == 'NEIGHBOR' cur_intf = cur_intf.remote_node.dfs_parent_intf else: not_done = False if ear_type == 'CHILD' and cur_intf.remote_node is x: # x is a cut-vertex and the local root for the block # in which the ear is computed x.IS_CUT_VERTEX = True localroot = x else: # inherit local root from the end of the ear localroot = cur_intf.remote_node.localroot while ear_list != []: y = ear_list.pop() y.localroot = localroot stack.append(y) def Construct_GADAG_via_Lowpoint(topo): gadag_root = topo.gadag_root gadag_root.IN_GADAG = True Enyedi, et al. Expires August 19, 2016 [Page 74] Internet-Draft MRT FRR Algorithm February 2016 gadag_root.localroot = None stack = [] stack.append(gadag_root) while stack != []: x = stack.pop() for intf in x.island_intf_list: if ( intf.remote_node.IN_GADAG == False and intf.remote_node.dfs_parent is x ): Construct_Ear(x, stack, intf, 'CHILD' ) for intf in x.island_intf_list: if (intf.remote_node.IN_GADAG == False and intf.remote_node.dfs_parent is not x): Construct_Ear(x, stack, intf, 'NEIGHBOR') def Assign_Remaining_Lowpoint_Parents(topo): for node in topo.island_node_list: if ( node is not topo.gadag_root and node.lowpoint_parent == None ): node.lowpoint_parent = node.dfs_parent node.lowpoint_parent_intf = node.dfs_parent_intf node.lowpoint_number = node.dfs_parent.dfs_number def Add_Undirected_Block_Root_Links(topo): for node in topo.island_node_list: if node.IS_CUT_VERTEX or node is topo.gadag_root: for intf in node.island_intf_list: if ( intf.remote_node.localroot is not node or intf.PROCESSED ): continue bundle_list = [] bundle = Bundle() for intf2 in node.island_intf_list: if intf2.remote_node is intf.remote_node: bundle_list.append(intf2) if not intf2.UNDIRECTED: bundle.UNDIRECTED = False if intf2.INCOMING: bundle.INCOMING = True if intf2.OUTGOING: bundle.OUTGOING = True if bundle.UNDIRECTED: for intf3 in bundle_list: intf3.UNDIRECTED = False intf3.remote_intf.UNDIRECTED = False intf3.PROCESSED = True intf3.remote_intf.PROCESSED = True intf3.OUTGOING = True intf3.remote_intf.INCOMING = True Enyedi, et al. Expires August 19, 2016 [Page 75] Internet-Draft MRT FRR Algorithm February 2016 else: if (bundle.OUTGOING and bundle.INCOMING): for intf3 in bundle_list: intf3.UNDIRECTED = False intf3.remote_intf.UNDIRECTED = False intf3.PROCESSED = True intf3.remote_intf.PROCESSED = True intf3.OUTGOING = True intf3.INCOMING = True intf3.remote_intf.INCOMING = True intf3.remote_intf.OUTGOING = True elif bundle.OUTGOING: for intf3 in bundle_list: intf3.UNDIRECTED = False intf3.remote_intf.UNDIRECTED = False intf3.PROCESSED = True intf3.remote_intf.PROCESSED = True intf3.OUTGOING = True intf3.remote_intf.INCOMING = True elif bundle.INCOMING: for intf3 in bundle_list: intf3.UNDIRECTED = False intf3.remote_intf.UNDIRECTED = False intf3.PROCESSED = True intf3.remote_intf.PROCESSED = True intf3.INCOMING = True intf3.remote_intf.OUTGOING = True def Modify_Block_Root_Incoming_Links(topo): for node in topo.island_node_list: if ( node.IS_CUT_VERTEX == True or node is topo.gadag_root ): for intf in node.island_intf_list: if intf.remote_node.localroot is node: if intf.INCOMING: intf.INCOMING = False intf.INCOMING_STORED = True intf.remote_intf.OUTGOING = False intf.remote_intf.OUTGOING_STORED = True def Revert_Block_Root_Incoming_Links(topo): for node in topo.island_node_list: if ( node.IS_CUT_VERTEX == True or node is topo.gadag_root ): for intf in node.island_intf_list: if intf.remote_node.localroot is node: if intf.INCOMING_STORED: intf.INCOMING = True intf.remote_intf.OUTGOING = True intf.INCOMING_STORED = False Enyedi, et al. Expires August 19, 2016 [Page 76] Internet-Draft MRT FRR Algorithm February 2016 intf.remote_intf.OUTGOING_STORED = False def Run_Topological_Sort_GADAG(topo): Modify_Block_Root_Incoming_Links(topo) for node in topo.island_node_list: node.unvisited = 0 for intf in node.island_intf_list: if (intf.INCOMING == True): node.unvisited += 1 working_list = [] topo_order_list = [] working_list.append(topo.gadag_root) while working_list != []: y = working_list.pop(0) topo_order_list.append(y) for intf in y.island_intf_list: if ( intf.OUTGOING == True): intf.remote_node.unvisited -= 1 if intf.remote_node.unvisited == 0: working_list.append(intf.remote_node) next_topo_order = 1 while topo_order_list != []: y = topo_order_list.pop(0) y.topo_order = next_topo_order next_topo_order += 1 Revert_Block_Root_Incoming_Links(topo) def Set_Other_Undirected_Links_Based_On_Topo_Order(topo): for node in topo.island_node_list: for intf in node.island_intf_list: if intf.UNDIRECTED: if node.topo_order < intf.remote_node.topo_order: intf.OUTGOING = True intf.UNDIRECTED = False intf.remote_intf.INCOMING = True intf.remote_intf.UNDIRECTED = False else: intf.INCOMING = True intf.UNDIRECTED = False intf.remote_intf.OUTGOING = True intf.remote_intf.UNDIRECTED = False def Initialize_Temporary_Interface_Flags(topo): for node in topo.island_node_list: for intf in node.island_intf_list: intf.PROCESSED = False intf.INCOMING_STORED = False intf.OUTGOING_STORED = False Enyedi, et al. Expires August 19, 2016 [Page 77] Internet-Draft MRT FRR Algorithm February 2016 def Add_Undirected_Links(topo): Initialize_Temporary_Interface_Flags(topo) Add_Undirected_Block_Root_Links(topo) Run_Topological_Sort_GADAG(topo) Set_Other_Undirected_Links_Based_On_Topo_Order(topo) def In_Common_Block(x,y): if ( (x.block_id == y.block_id) or ( x is y.localroot) or (y is x.localroot) ): return True return False def Copy_List_Items(target_list, source_list): del target_list[:] # Python idiom to remove all elements of a list for element in source_list: target_list.append(element) def Add_Item_To_List_If_New(target_list, item): if item not in target_list: target_list.append(item) def Store_Results(y, direction): if direction == 'INCREASING': y.HIGHER = True Copy_List_Items(y.blue_next_hops, y.next_hops) if direction == 'DECREASING': y.LOWER = True Copy_List_Items(y.red_next_hops, y.next_hops) if direction == 'NORMAL_SPF': y.primary_spf_metric = y.spf_metric Copy_List_Items(y.primary_next_hops, y.next_hops) if direction == 'MRT_ISLAND_SPF': Copy_List_Items(y.mrt_island_next_hops, y.next_hops) if direction == 'COLLAPSED_SPF': y.collapsed_metric = y.spf_metric Copy_List_Items(y.collapsed_next_hops, y.next_hops) # Note that the Python heapq fucntion allows for duplicate items, # so we use the 'spf_visited' property to only consider a node # as min_node the first time it gets removed from the heap. def SPF_No_Traverse_Block_Root(topo, spf_root, block_root, direction): spf_heap = [] for y in topo.island_node_list: y.spf_metric = 2147483647 # 2^31-1 y.next_hops = [] y.spf_visited = False spf_root.spf_metric = 0 heapq.heappush(spf_heap, Enyedi, et al. Expires August 19, 2016 [Page 78] Internet-Draft MRT FRR Algorithm February 2016 (spf_root.spf_metric, spf_root.node_id, spf_root) ) while spf_heap != []: #extract third element of tuple popped from heap min_node = heapq.heappop(spf_heap)[2] if min_node.spf_visited: continue min_node.spf_visited = True Store_Results(min_node, direction) if ( (min_node is spf_root) or (min_node is not block_root) ): for intf in min_node.island_intf_list: if ( ( (direction == 'INCREASING' and intf.OUTGOING ) or (direction == 'DECREASING' and intf.INCOMING ) ) and In_Common_Block(spf_root, intf.remote_node) ) : path_metric = min_node.spf_metric + intf.metric if path_metric < intf.remote_node.spf_metric: intf.remote_node.spf_metric = path_metric if min_node is spf_root: intf.remote_node.next_hops = [intf] else: Copy_List_Items(intf.remote_node.next_hops, min_node.next_hops) heapq.heappush(spf_heap, ( intf.remote_node.spf_metric, intf.remote_node.node_id, intf.remote_node ) ) elif path_metric == intf.remote_node.spf_metric: if min_node is spf_root: Add_Item_To_List_If_New( intf.remote_node.next_hops,intf) else: for nh_intf in min_node.next_hops: Add_Item_To_List_If_New( intf.remote_node.next_hops,nh_intf) def Normal_SPF(topo, spf_root): spf_heap = [] for y in topo.node_list: y.spf_metric = 2147483647 # 2^31-1 as max metric y.next_hops = [] y.primary_spf_metric = 2147483647 y.primary_next_hops = [] y.spf_visited = False spf_root.spf_metric = 0 heapq.heappush(spf_heap, (spf_root.spf_metric,spf_root.node_id,spf_root) ) while spf_heap != []: #extract third element of tuple popped from heap min_node = heapq.heappop(spf_heap)[2] Enyedi, et al. Expires August 19, 2016 [Page 79] Internet-Draft MRT FRR Algorithm February 2016 if min_node.spf_visited: continue min_node.spf_visited = True Store_Results(min_node, 'NORMAL_SPF') for intf in min_node.intf_list: path_metric = min_node.spf_metric + intf.metric if path_metric < intf.remote_node.spf_metric: intf.remote_node.spf_metric = path_metric if min_node is spf_root: intf.remote_node.next_hops = [intf] else: Copy_List_Items(intf.remote_node.next_hops, min_node.next_hops) heapq.heappush(spf_heap, ( intf.remote_node.spf_metric, intf.remote_node.node_id, intf.remote_node ) ) elif path_metric == intf.remote_node.spf_metric: if min_node is spf_root: Add_Item_To_List_If_New( intf.remote_node.next_hops,intf) else: for nh_intf in min_node.next_hops: Add_Item_To_List_If_New( intf.remote_node.next_hops,nh_intf) def Set_Edge(y): if (y.blue_next_hops == [] and y.red_next_hops == []): Set_Edge(y.localroot) Copy_List_Items(y.blue_next_hops,y.localroot.blue_next_hops) Copy_List_Items(y.red_next_hops ,y.localroot.red_next_hops) y.order_proxy = y.localroot.order_proxy def Compute_MRT_NH_For_One_Src_To_Island_Dests(topo,x): for y in topo.island_node_list: y.HIGHER = False y.LOWER = False y.red_next_hops = [] y.blue_next_hops = [] y.order_proxy = y SPF_No_Traverse_Block_Root(topo, x, x.localroot, 'INCREASING') SPF_No_Traverse_Block_Root(topo, x, x.localroot, 'DECREASING') for y in topo.island_node_list: if ( y is not x and (y.block_id == x.block_id) ): assert (not ( y is x.localroot or x is y.localroot) ) assert(not (y.HIGHER and y.LOWER) ) if y.HIGHER == True: Copy_List_Items(y.red_next_hops, Enyedi, et al. Expires August 19, 2016 [Page 80] Internet-Draft MRT FRR Algorithm February 2016 x.localroot.red_next_hops) elif y.LOWER == True: Copy_List_Items(y.blue_next_hops, x.localroot.blue_next_hops) else: Copy_List_Items(y.blue_next_hops, x.localroot.red_next_hops) Copy_List_Items(y.red_next_hops, x.localroot.blue_next_hops) # Inherit x's MRT next-hops to reach the GADAG root # from x's MRT next-hops to reach its local root, # but first check if x is the gadag_root (in which case # x does not have a local root) or if x's local root # is the gadag root (in which case we already have the # x's MRT next-hops to reach the gadag root) if x is not topo.gadag_root and x.localroot is not topo.gadag_root: Copy_List_Items(topo.gadag_root.blue_next_hops, x.localroot.blue_next_hops) Copy_List_Items(topo.gadag_root.red_next_hops, x.localroot.red_next_hops) topo.gadag_root.order_proxy = x.localroot # Inherit next-hops and order_proxies to other blocks for y in topo.island_node_list: if (y is not topo.gadag_root and y is not x ): Set_Edge(y) def Store_MRT_Nexthops_For_One_Src_To_Island_Dests(topo,x): for y in topo.island_node_list: if y is x: continue x.blue_next_hops_dict[y.node_id] = [] x.red_next_hops_dict[y.node_id] = [] Copy_List_Items(x.blue_next_hops_dict[y.node_id], y.blue_next_hops) Copy_List_Items(x.red_next_hops_dict[y.node_id], y.red_next_hops) def Store_Primary_and_Alts_For_One_Src_To_Island_Dests(topo,x): for y in topo.island_node_list: x.pnh_dict[y.node_id] = [] Copy_List_Items(x.pnh_dict[y.node_id], y.primary_next_hops) x.alt_dict[y.node_id] = [] Copy_List_Items(x.alt_dict[y.node_id], y.alt_list) def Store_Primary_NHs_For_One_Source_To_Nodes(topo,x): for y in topo.node_list: Enyedi, et al. Expires August 19, 2016 [Page 81] Internet-Draft MRT FRR Algorithm February 2016 x.pnh_dict[y.node_id] = [] Copy_List_Items(x.pnh_dict[y.node_id], y.primary_next_hops) def Store_MRT_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,x): for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] x.blue_next_hops_dict[P.node_id] = [] x.red_next_hops_dict[P.node_id] = [] Copy_List_Items(x.blue_next_hops_dict[P.node_id], P.blue_next_hops) Copy_List_Items(x.red_next_hops_dict[P.node_id], P.red_next_hops) def Store_Alts_For_One_Src_To_Named_Proxy_Nodes(topo,x): for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] x.alt_dict[P.node_id] = [] Copy_List_Items(x.alt_dict[P.node_id], P.alt_list) def Store_Primary_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,x): for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] x.pnh_dict[P.node_id] = [] Copy_List_Items(x.pnh_dict[P.node_id], P.primary_next_hops) def Select_Alternates_Internal(D, F, primary_intf, D_lower, D_higher, D_topo_order): if D_higher and D_lower: if F.HIGHER and F.LOWER: if F.topo_order > D_topo_order: return 'USE_BLUE' else: return 'USE_RED' if F.HIGHER: return 'USE_RED' if F.LOWER: return 'USE_BLUE' assert(primary_intf.MRT_INELIGIBLE or primary_intf.remote_intf.MRT_INELIGIBLE) return 'USE_RED_OR_BLUE' if D_higher: if F.HIGHER and F.LOWER: return 'USE_BLUE' if F.LOWER: return 'USE_BLUE' if F.HIGHER: Enyedi, et al. Expires August 19, 2016 [Page 82] Internet-Draft MRT FRR Algorithm February 2016 if (F.topo_order > D_topo_order): return 'USE_BLUE' if (F.topo_order < D_topo_order): return 'USE_RED' assert(False) assert(primary_intf.MRT_INELIGIBLE or primary_intf.remote_intf.MRT_INELIGIBLE) return 'USE_RED_OR_BLUE' if D_lower: if F.HIGHER and F.LOWER: return 'USE_RED' if F.HIGHER: return 'USE_RED' if F.LOWER: if F.topo_order > D_topo_order: return 'USE_BLUE' if F.topo_order < D_topo_order: return 'USE_RED' assert(False) assert(primary_intf.MRT_INELIGIBLE or primary_intf.remote_intf.MRT_INELIGIBLE) return 'USE_RED_OR_BLUE' else: # D is unordered wrt S if F.HIGHER and F.LOWER: if primary_intf.OUTGOING and primary_intf.INCOMING: # This can happen when F and D are in different blocks return 'USE_RED_OR_BLUE' if primary_intf.OUTGOING: return 'USE_BLUE' if primary_intf.INCOMING: return 'USE_RED' #This can occur when primary_intf is MRT_INELIGIBLE. #This appears to be a case where the special #construction of the GADAG allows us to choose red, #whereas with an arbitrary GADAG, neither red nor blue #is guaranteed to work. assert(primary_intf.MRT_INELIGIBLE or primary_intf.remote_intf.MRT_INELIGIBLE) return 'USE_RED' if F.LOWER: return 'USE_RED' if F.HIGHER: return 'USE_BLUE' assert(primary_intf.MRT_INELIGIBLE or primary_intf.remote_intf.MRT_INELIGIBLE) if F.topo_order > D_topo_order: return 'USE_BLUE' else: Enyedi, et al. Expires August 19, 2016 [Page 83] Internet-Draft MRT FRR Algorithm February 2016 return 'USE_RED' def Select_Alternates(D, F, primary_intf): S = primary_intf.local_node if not In_Common_Block(F, S): return 'PRIM_NH_IN_DIFFERENT_BLOCK' if (D is F) or (D.order_proxy is F): return 'PRIM_NH_IS_D_OR_OP_FOR_D' D_lower = D.order_proxy.LOWER D_higher = D.order_proxy.HIGHER D_topo_order = D.order_proxy.topo_order return Select_Alternates_Internal(D, F, primary_intf, D_lower, D_higher, D_topo_order) def Is_Remote_Node_In_NH_List(node, intf_list): for intf in intf_list: if node is intf.remote_node: return True return False def Select_Alts_For_One_Src_To_Island_Dests(topo,x): Normal_SPF(topo, x) for D in topo.island_node_list: D.alt_list = [] if D is x: continue for failed_intf in D.primary_next_hops: alt = Alternate() alt.failed_intf = failed_intf cand_alt_list = [] F = failed_intf.remote_node #We need to test if F is in the island, as opposed #to just testing if failed_intf is in island_intf_list, #because failed_intf could be marked as MRT_INELIGIBLE. if F in topo.island_node_list: alt.info = Select_Alternates(D, F, failed_intf) else: #The primary next-hop is not in the MRT Island. #Either red or blue will avoid the primary next-hop, #because the primary next-hop is not even in the #GADAG. alt.info = 'USE_RED_OR_BLUE' if (alt.info == 'USE_RED_OR_BLUE'): alt.red_or_blue = random.choice(['USE_RED','USE_BLUE']) if (alt.info == 'USE_BLUE' or alt.red_or_blue == 'USE_BLUE'): Enyedi, et al. Expires August 19, 2016 [Page 84] Internet-Draft MRT FRR Algorithm February 2016 Copy_List_Items(alt.nh_list, D.blue_next_hops) alt.fec = 'BLUE' alt.prot = 'NODE_PROTECTION' if (alt.info == 'USE_RED' or alt.red_or_blue == 'USE_RED'): Copy_List_Items(alt.nh_list, D.red_next_hops) alt.fec = 'RED' alt.prot = 'NODE_PROTECTION' if (alt.info == 'PRIM_NH_IN_DIFFERENT_BLOCK'): alt.fec = 'NO_ALTERNATE' alt.prot = 'NO_PROTECTION' if (alt.info == 'PRIM_NH_IS_D_OR_OP_FOR_D'): if failed_intf.OUTGOING and failed_intf.INCOMING: # cut-link: if there are parallel cut links, use # the link(s) with lowest metric that are not # primary intf or None cand_alt_list = [None] min_metric = 2147483647 for intf in x.island_intf_list: if ( intf is not failed_intf and (intf.remote_node is failed_intf.remote_node)): if intf.metric < min_metric: cand_alt_list = [intf] min_metric = intf.metric elif intf.metric == min_metric: cand_alt_list.append(intf) if cand_alt_list != [None]: alt.fec = 'GREEN' alt.prot = 'PARALLEL_CUTLINK' else: alt.fec = 'NO_ALTERNATE' alt.prot = 'NO_PROTECTION' Copy_List_Items(alt.nh_list, cand_alt_list) # Is_Remote_Node_In_NH_List() is used, as opposed # to just checking if failed_intf is in D.red_next_hops, # because failed_intf could be marked as MRT_INELIGIBLE. elif Is_Remote_Node_In_NH_List(F, D.red_next_hops): Copy_List_Items(alt.nh_list, D.blue_next_hops) alt.fec = 'BLUE' alt.prot = 'LINK_PROTECTION' elif Is_Remote_Node_In_NH_List(F, D.blue_next_hops): Copy_List_Items(alt.nh_list, D.red_next_hops) alt.fec = 'RED' alt.prot = 'LINK_PROTECTION' else: alt.fec = random.choice(['RED','BLUE']) alt.prot = 'LINK_PROTECTION' Enyedi, et al. Expires August 19, 2016 [Page 85] Internet-Draft MRT FRR Algorithm February 2016 D.alt_list.append(alt) def Write_GADAG_To_File(topo, file_prefix): gadag_edge_list = [] for node in topo.node_list: for intf in node.intf_list: if intf.SIMULATION_OUTGOING: local_node = "%04d" % (intf.local_node.node_id) remote_node = "%04d" % (intf.remote_node.node_id) intf_data = "%03d" % (intf.link_data) edge_string=(local_node+','+remote_node+','+ intf_data+'\n') gadag_edge_list.append(edge_string) gadag_edge_list.sort(); filename = file_prefix + '_gadag.csv' with open(filename, 'w') as gadag_file: gadag_file.write('local_node,'\ 'remote_node,local_intf_link_data\n') for edge_string in gadag_edge_list: gadag_file.write(edge_string); def Write_MRTs_For_All_Dests_To_File(topo, color, file_prefix): edge_list = [] for node in topo.island_node_list_for_test_gr: if color == 'blue': node_next_hops_dict = node.blue_next_hops_dict elif color == 'red': node_next_hops_dict = node.red_next_hops_dict for dest_node_id in node_next_hops_dict: for intf in node_next_hops_dict[dest_node_id]: gadag_root = "%04d" % (topo.gadag_root.node_id) dest_node = "%04d" % (dest_node_id) local_node = "%04d" % (intf.local_node.node_id) remote_node = "%04d" % (intf.remote_node.node_id) intf_data = "%03d" % (intf.link_data) edge_string=(gadag_root+','+dest_node+','+local_node+ ','+remote_node+','+intf_data+'\n') edge_list.append(edge_string) edge_list.sort() filename = file_prefix + '_' + color + '_to_all.csv' with open(filename, 'w') as mrt_file: mrt_file.write('gadag_root,dest,'\ 'local_node,remote_node,link_data\n') for edge_string in edge_list: mrt_file.write(edge_string); def Write_Both_MRTs_For_All_Dests_To_File(topo, file_prefix): Write_MRTs_For_All_Dests_To_File(topo, 'blue', file_prefix) Enyedi, et al. Expires August 19, 2016 [Page 86] Internet-Draft MRT FRR Algorithm February 2016 Write_MRTs_For_All_Dests_To_File(topo, 'red', file_prefix) def Write_Alternates_For_All_Dests_To_File(topo, file_prefix): edge_list = [] for x in topo.island_node_list_for_test_gr: for dest_node_id in x.alt_dict: alt_list = x.alt_dict[dest_node_id] for alt in alt_list: for alt_intf in alt.nh_list: gadag_root = "%04d" % (topo.gadag_root.node_id) dest_node = "%04d" % (dest_node_id) prim_local_node = \ "%04d" % (alt.failed_intf.local_node.node_id) prim_remote_node = \ "%04d" % (alt.failed_intf.remote_node.node_id) prim_intf_data = \ "%03d" % (alt.failed_intf.link_data) if alt_intf == None: alt_local_node = "None" alt_remote_node = "None" alt_intf_data = "None" else: alt_local_node = \ "%04d" % (alt_intf.local_node.node_id) alt_remote_node = \ "%04d" % (alt_intf.remote_node.node_id) alt_intf_data = \ "%03d" % (alt_intf.link_data) edge_string = (gadag_root+','+dest_node+','+ prim_local_node+','+prim_remote_node+','+ prim_intf_data+','+alt_local_node+','+ alt_remote_node+','+alt_intf_data+','+ alt.fec +'\n') edge_list.append(edge_string) edge_list.sort() filename = file_prefix + '_alts_to_all.csv' with open(filename, 'w') as alt_file: alt_file.write('gadag_root,dest,'\ 'prim_nh.local_node,prim_nh.remote_node,'\ 'prim_nh.link_data,alt_nh.local_node,'\ 'alt_nh.remote_node,alt_nh.link_data,'\ 'alt_nh.fec\n') for edge_string in edge_list: alt_file.write(edge_string); def Raise_GADAG_Root_Selection_Priority(topo,node_id): node = topo.node_dict[node_id] node.GR_sel_priority = 255 Enyedi, et al. Expires August 19, 2016 [Page 87] Internet-Draft MRT FRR Algorithm February 2016 def Lower_GADAG_Root_Selection_Priority(topo,node_id): node = topo.node_dict[node_id] node.GR_sel_priority = 128 def GADAG_Root_Compare(node_a, node_b): if (node_a.GR_sel_priority > node_b.GR_sel_priority): return 1 elif (node_a.GR_sel_priority < node_b.GR_sel_priority): return -1 else: if node_a.node_id > node_b.node_id: return 1 elif node_a.node_id < node_b.node_id: return -1 def Set_GADAG_Root(topo,computing_router): gadag_root_list = [] for node in topo.island_node_list: gadag_root_list.append(node) gadag_root_list.sort(GADAG_Root_Compare) topo.gadag_root = gadag_root_list.pop() def Add_Prefix_Advertisements_From_File(topo, filename): prefix_filename = filename + '.prefix' cols_list = [] if not os.path.exists(prefix_filename): return with open(prefix_filename) as prefix_file: for line in prefix_file: line = line.rstrip('\r\n') cols=line.split(',') cols_list.append(cols) prefix_id = int(cols[0]) if prefix_id < 2000 or prefix_id >2999: print('skipping the following line of prefix file') print('prefix id should be between 2000 and 2999') print(line) continue prefix_node_id = int(cols[1]) prefix_cost = int(cols[2]) advertising_node = topo.node_dict[prefix_node_id] advertising_node.prefix_cost_dict[prefix_id] = prefix_cost def Add_Prefixes_for_Non_Island_Nodes(topo): for node in topo.node_list: if node.IN_MRT_ISLAND: continue prefix_id = node.node_id + 1000 Enyedi, et al. Expires August 19, 2016 [Page 88] Internet-Draft MRT FRR Algorithm February 2016 node.prefix_cost_dict[prefix_id] = 0 def Add_Profile_IDs_from_File(topo, filename): profile_filename = filename + '.profile' for node in topo.node_list: node.profile_id_list = [] cols_list = [] if os.path.exists(profile_filename): with open(profile_filename) as profile_file: for line in profile_file: line = line.rstrip('\r\n') cols=line.split(',') cols_list.append(cols) node_id = int(cols[0]) profile_id = int(cols[1]) this_node = topo.node_dict[node_id] this_node.profile_id_list.append(profile_id) else: for node in topo.node_list: node.profile_id_list = [0] def Island_Marking_SPF(topo,spf_root): spf_root.isl_marking_spf_dict = {} for y in topo.node_list: y.spf_metric = 2147483647 # 2^31-1 as max metric y.PATH_HITS_ISLAND = False y.next_hops = [] y.spf_visited = False spf_root.spf_metric = 0 spf_heap = [] heapq.heappush(spf_heap, (spf_root.spf_metric,spf_root.node_id,spf_root) ) while spf_heap != []: #extract third element of tuple popped from heap min_node = heapq.heappop(spf_heap)[2] if min_node.spf_visited: continue min_node.spf_visited = True spf_root.isl_marking_spf_dict[min_node.node_id] = \ (min_node.spf_metric, min_node.PATH_HITS_ISLAND) for intf in min_node.intf_list: path_metric = min_node.spf_metric + intf.metric if path_metric < intf.remote_node.spf_metric: intf.remote_node.spf_metric = path_metric if min_node is spf_root: intf.remote_node.next_hops = [intf] else: Copy_List_Items(intf.remote_node.next_hops, Enyedi, et al. Expires August 19, 2016 [Page 89] Internet-Draft MRT FRR Algorithm February 2016 min_node.next_hops) if (intf.remote_node.IN_MRT_ISLAND): intf.remote_node.PATH_HITS_ISLAND = True else: intf.remote_node.PATH_HITS_ISLAND = \ min_node.PATH_HITS_ISLAND heapq.heappush(spf_heap, ( intf.remote_node.spf_metric, intf.remote_node.node_id, intf.remote_node ) ) elif path_metric == intf.remote_node.spf_metric: if min_node is spf_root: Add_Item_To_List_If_New( intf.remote_node.next_hops,intf) else: for nh_intf in min_node.next_hops: Add_Item_To_List_If_New( intf.remote_node.next_hops,nh_intf) if (intf.remote_node.IN_MRT_ISLAND): intf.remote_node.PATH_HITS_ISLAND = True else: if (intf.remote_node.PATH_HITS_ISLAND or min_node.PATH_HITS_ISLAND): intf.remote_node.PATH_HITS_ISLAND = True def Create_Basic_Named_Proxy_Nodes(topo): for node in topo.node_list: for prefix in node.prefix_cost_dict: prefix_cost = node.prefix_cost_dict[prefix] if prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] P.node_prefix_cost_list.append((node,prefix_cost)) else: P = Named_Proxy_Node() topo.named_proxy_dict[prefix] = P P.node_id = prefix P.node_prefix_cost_list = [(node,prefix_cost)] def Compute_Loop_Free_Island_Neighbors_For_Each_Prefix(topo): topo.island_nbr_set = set() topo.island_border_set = set() for node in topo.node_list: if node.IN_MRT_ISLAND: continue for intf in node.intf_list: if intf.remote_node.IN_MRT_ISLAND: topo.island_nbr_set.add(node) Enyedi, et al. Expires August 19, 2016 [Page 90] Internet-Draft MRT FRR Algorithm February 2016 topo.island_border_set.add(intf.remote_node) for island_nbr in topo.island_nbr_set: Island_Marking_SPF(topo,island_nbr) for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] P.lfin_list = [] for island_nbr in topo.island_nbr_set: min_isl_nbr_to_pref_cost = 2147483647 for (adv_node, prefix_cost) in P.node_prefix_cost_list: (adv_node_cost, path_hits_island) = \ island_nbr.isl_marking_spf_dict[adv_node.node_id] isl_nbr_to_pref_cost = adv_node_cost + prefix_cost if isl_nbr_to_pref_cost < min_isl_nbr_to_pref_cost: min_isl_nbr_to_pref_cost = isl_nbr_to_pref_cost min_path_hits_island = path_hits_island elif isl_nbr_to_pref_cost == min_isl_nbr_to_pref_cost: if min_path_hits_island or path_hits_island: min_path_hits_island = True if not min_path_hits_island: P.lfin_list.append( (island_nbr, min_isl_nbr_to_pref_cost) ) def Compute_Island_Border_Router_LFIN_Pairs_For_Each_Prefix(topo): for ibr in topo.island_border_set: ibr.prefix_lfin_dict = {} ibr.min_intf_metric_dict = {} ibr.min_intf_list_dict = {} ibr.min_intf_list_dict[None] = None for intf in ibr.intf_list: if not intf.remote_node in topo.island_nbr_set: continue if not intf.remote_node in ibr.min_intf_metric_dict: ibr.min_intf_metric_dict[intf.remote_node] = \ intf.metric ibr.min_intf_list_dict[intf.remote_node] = [intf] else: if (intf.metric < ibr.min_intf_metric_dict[intf.remote_node]): ibr.min_intf_metric_dict[intf.remote_node] = \ intf.metric ibr.min_intf_list_dict[intf.remote_node] = [intf] elif (intf.metric < ibr.min_intf_metric_dict[intf.remote_node]): ibr.min_intf_list_dict[intf.remote_node].\ append(intf) Enyedi, et al. Expires August 19, 2016 [Page 91] Internet-Draft MRT FRR Algorithm February 2016 for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] for ibr in topo.island_border_set: min_ibr_lfin_pref_cost = 2147483647 min_lfin = None for (lfin, lfin_to_pref_cost) in P.lfin_list: if not lfin in ibr.min_intf_metric_dict: continue ibr_lfin_pref_cost = \ ibr.min_intf_metric_dict[lfin] + lfin_to_pref_cost if ibr_lfin_pref_cost < min_ibr_lfin_pref_cost: min_ibr_lfin_pref_cost = ibr_lfin_pref_cost min_lfin = lfin ibr.prefix_lfin_dict[prefix] = (min_lfin, min_ibr_lfin_pref_cost, ibr.min_intf_list_dict[min_lfin]) def Proxy_Node_Att_Router_Compare(pnar_a, pnar_b): if pnar_a.named_proxy_cost < pnar_b.named_proxy_cost: return -1 if pnar_b.named_proxy_cost < pnar_a.named_proxy_cost: return 1 if pnar_a.node.node_id < pnar_b.node.node_id: return -1 if pnar_b.node.node_id < pnar_a.node.node_id: return 1 if pnar_a.min_lfin == None: return -1 if pnar_b.min_lfin == None: return 1 def Choose_Proxy_Node_Attachment_Routers(topo): for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] pnar_candidate_list = [] for (node, prefix_cost) in P.node_prefix_cost_list: if not node.IN_MRT_ISLAND: continue pnar = Proxy_Node_Attachment_Router() pnar.prefix = prefix pnar.named_proxy_cost = prefix_cost pnar.node = node pnar_candidate_list.append(pnar) for ibr in topo.island_border_set: (min_lfin, prefix_cost, min_intf_list) = \ ibr.prefix_lfin_dict[prefix] if min_lfin == None: continue Enyedi, et al. Expires August 19, 2016 [Page 92] Internet-Draft MRT FRR Algorithm February 2016 pnar = Proxy_Node_Attachment_Router() pnar.named_proxy_cost = prefix_cost pnar.node = ibr pnar.min_lfin = min_lfin pnar.nh_intf_list = min_intf_list pnar_candidate_list.append(pnar) pnar_candidate_list.sort(cmp=Proxy_Node_Att_Router_Compare) #pop first element from list first_pnar = pnar_candidate_list.pop(0) second_pnar = None for next_pnar in pnar_candidate_list: if next_pnar.node is first_pnar.node: continue second_pnar = next_pnar break P.pnar1 = first_pnar P.pnar2 = second_pnar def Attach_Named_Proxy_Nodes(topo): Compute_Loop_Free_Island_Neighbors_For_Each_Prefix(topo) Compute_Island_Border_Router_LFIN_Pairs_For_Each_Prefix(topo) Choose_Proxy_Node_Attachment_Routers(topo) def Select_Proxy_Node_NHs(P,S): if P.pnar1.node.node_id < P.pnar2.node.node_id: X = P.pnar1.node Y = P.pnar2.node else: X = P.pnar2.node Y = P.pnar1.node P.pnar_X = X P.pnar_Y = Y A = X.order_proxy B = Y.order_proxy if (A is S.localroot and B is S.localroot): #print("1.0") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if (A is S.localroot and B is not S.localroot): #print("2.0") if B.LOWER: #print("2.1") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) Enyedi, et al. Expires August 19, 2016 [Page 93] Internet-Draft MRT FRR Algorithm February 2016 return if B.HIGHER: #print("2.2") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: #print("2.3") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if (A is not S.localroot and B is S.localroot): #print("3.0") if A.LOWER: #print("3.1") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if A.HIGHER: #print("3.2") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: #print("3.3") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if (A is not S.localroot and B is not S.localroot): #print("4.0") if (S is A.localroot or S is B.localroot): #print("4.05") if A.topo_order < B.topo_order: #print("4.05.1") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: #print("4.05.2") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if A.LOWER: #print("4.1") if B.HIGHER: #print("4.1.1") Enyedi, et al. Expires August 19, 2016 [Page 94] Internet-Draft MRT FRR Algorithm February 2016 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if B.LOWER: #print("4.1.2") if A.topo_order < B.topo_order: #print("4.1.2.1") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: #print("4.1.2.2") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: #print("4.1.3") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if A.HIGHER: #print("4.2") if B.HIGHER: #print("4.2.1") if A.topo_order < B.topo_order: #print("4.2.1.1") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: #print("4.2.1.2") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return if B.LOWER: #print("4.2.2") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: #print("4.2.3") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: #print("4.3") if B.LOWER: #print("4.3.1") Enyedi, et al. Expires August 19, 2016 [Page 95] Internet-Draft MRT FRR Algorithm February 2016 Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return if B.HIGHER: #print("4.3.2") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return else: #print("4.3.3") if A.topo_order < B.topo_order: #print("4.3.3.1") Copy_List_Items(P.blue_next_hops, X.blue_next_hops) Copy_List_Items(P.red_next_hops, Y.red_next_hops) return else: #print("4.3.3.2") Copy_List_Items(P.blue_next_hops, X.red_next_hops) Copy_List_Items(P.red_next_hops, Y.blue_next_hops) return assert(False) def Compute_MRT_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,S): for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] if P.pnar2 == None: if S is P.pnar1.node: # set the MRT next-hops for the PNAR to # reach the LFIN and change FEC to green Copy_List_Items(P.blue_next_hops, P.pnar1.nh_intf_list) S.blue_to_green_nh_dict[P.node_id] = True Copy_List_Items(P.red_next_hops, P.pnar1.nh_intf_list) S.red_to_green_nh_dict[P.node_id] = True else: # inherit MRT NHs for P from pnar1 Copy_List_Items(P.blue_next_hops, P.pnar1.node.blue_next_hops) Copy_List_Items(P.red_next_hops, P.pnar1.node.red_next_hops) else: Select_Proxy_Node_NHs(P,S) # set the MRT next-hops for the PNAR to reach the LFIN # and change FEC to green rely on the red or blue # next-hops being empty to figure out which one needs # to point to the LFIN. if S is P.pnar1.node: Enyedi, et al. Expires August 19, 2016 [Page 96] Internet-Draft MRT FRR Algorithm February 2016 this_pnar = P.pnar1 elif S is P.pnar2.node: this_pnar = P.pnar2 else: continue if P.blue_next_hops == []: Copy_List_Items(P.blue_next_hops, this_pnar.nh_intf_list) S.blue_to_green_nh_dict[P.node_id] = True if P.red_next_hops == []: Copy_List_Items(P.red_next_hops, this_pnar.nh_intf_list) S.red_to_green_nh_dict[P.node_id] = True def Select_Alternates_Proxy_Node(P,F,primary_intf): S = primary_intf.local_node X = P.pnar_X Y = P.pnar_Y A = X.order_proxy B = Y.order_proxy if F is A and F is B: return 'PRIM_NH_IS_OP_FOR_BOTH_X_AND_Y' if F is A: return 'USE_RED' if F is B: return 'USE_BLUE' if not In_Common_Block(A, B): if In_Common_Block(F, A): return 'USE_RED' elif In_Common_Block(F, B): return 'USE_BLUE' else: return 'USE_RED_OR_BLUE' if (not In_Common_Block(F, A) and not In_Common_Block(F, A) ): return 'USE_RED_OR_BLUE' alt_to_X = Select_Alternates(X, F, primary_intf) alt_to_Y = Select_Alternates(Y, F, primary_intf) if (alt_to_X == 'USE_RED_OR_BLUE' and alt_to_Y == 'USE_RED_OR_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED_OR_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED_OR_BLUE': return 'USE_RED' Enyedi, et al. Expires August 19, 2016 [Page 97] Internet-Draft MRT FRR Algorithm February 2016 if (A is S.localroot and B is S.localroot): #print("1.0") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if (A is S.localroot and B is not S.localroot): #print("2.0") if B.LOWER: #print("2.1") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if B.HIGHER: #print("2.2") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) else: #print("2.3") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if (A is not S.localroot and B is S.localroot): #print("3.0") if A.LOWER: #print("3.1") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': Enyedi, et al. Expires August 19, 2016 [Page 98] Internet-Draft MRT FRR Algorithm February 2016 return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if A.HIGHER: #print("3.2") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: #print("3.3") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) if (A is not S.localroot and B is not S.localroot): #print("4.0") if (S is A.localroot or S is B.localroot): #print("4.05") if A.topo_order < B.topo_order: #print("4.05.1") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: #print("4.05.2") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if A.LOWER: #print("4.1") if B.HIGHER: Enyedi, et al. Expires August 19, 2016 [Page 99] Internet-Draft MRT FRR Algorithm February 2016 #print("4.1.1") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if B.LOWER: #print("4.1.2") if A.topo_order < B.topo_order: #print("4.1.2.1") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: #print("4.1.2.2") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) else: #print("4.1.3") if (F.LOWER and not F.HIGHER and F.topo_order > A.topo_order): #print("4.1.3.1") return 'USE_RED' else: #print("4.1.3.2") return 'USE_BLUE' if A.HIGHER: #print("4.2") if B.HIGHER: #print("4.2.1") if A.topo_order < B.topo_order: #print("4.2.1.1") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' Enyedi, et al. Expires August 19, 2016 [Page 100] Internet-Draft MRT FRR Algorithm February 2016 if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: #print("4.2.1.2") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) if B.LOWER: #print("4.2.2") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: #print("4.2.3") if (F.HIGHER and not F.LOWER and F.topo_order < A.topo_order): return 'USE_RED' else: return 'USE_BLUE' else: #print("4.3") if B.LOWER: #print("4.3.1") if (F.LOWER and not F.HIGHER and F.topo_order > B.topo_order): return 'USE_BLUE' else: return 'USE_RED' if B.HIGHER: #print("4.3.2") if (F.HIGHER and not F.LOWER and F.topo_order < B.topo_order): return 'USE_BLUE' else: return 'USE_RED' Enyedi, et al. Expires August 19, 2016 [Page 101] Internet-Draft MRT FRR Algorithm February 2016 else: #print("4.3.3") if A.topo_order < B.topo_order: #print("4.3.3.1") if (alt_to_X == 'USE_BLUE' and alt_to_Y == 'USE_RED'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_BLUE': return 'USE_BLUE' if alt_to_Y == 'USE_RED': return 'USE_RED' assert(False) else: #print("4.3.3.2") if (alt_to_X == 'USE_RED' and alt_to_Y == 'USE_BLUE'): return 'USE_RED_OR_BLUE' if alt_to_X == 'USE_RED': return 'USE_BLUE' if alt_to_Y == 'USE_BLUE': return 'USE_RED' assert(False) assert(False) def Compute_Primary_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,src): for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] min_total_pref_cost = 2147483647 for (adv_node, prefix_cost) in P.node_prefix_cost_list: total_pref_cost = (adv_node.primary_spf_metric + prefix_cost) if total_pref_cost < min_total_pref_cost: min_total_pref_cost = total_pref_cost Copy_List_Items(P.primary_next_hops, adv_node.primary_next_hops) elif total_pref_cost == min_total_pref_cost: for nh_intf in adv_node.primary_next_hops: Add_Item_To_List_If_New(P.primary_next_hops, nh_intf) def Select_Alts_For_One_Src_To_Named_Proxy_Nodes(topo,src): for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] P.alt_list = [] for failed_intf in P.primary_next_hops: alt = Alternate() alt.failed_intf = failed_intf if failed_intf not in src.island_intf_list: Enyedi, et al. Expires August 19, 2016 [Page 102] Internet-Draft MRT FRR Algorithm February 2016 alt.info = 'PRIM_NH_FOR_PROXY_NODE_NOT_IN_ISLAND' elif P.pnar1 is None: alt.info = 'NO_PNARs_EXIST_FOR_THIS_PREFIX' elif src is P.pnar1.node: alt.info = 'SRC_IS_PNAR' elif P.pnar2 is not None and src is P.pnar2.node: alt.info = 'SRC_IS_PNAR' elif P.pnar2 is None: #inherit alternates from the only pnar. alt.info = Select_Alternates(P.pnar1.node, failed_intf.remote_node, failed_intf) elif failed_intf in src.island_intf_list: alt.info = Select_Alternates_Proxy_Node(P, failed_intf.remote_node, failed_intf) if alt.info == 'USE_RED_OR_BLUE': alt.red_or_blue = \ random.choice(['USE_RED','USE_BLUE']) if (alt.info == 'USE_BLUE' or alt.red_or_blue == 'USE_BLUE'): Copy_List_Items(alt.nh_list, P.blue_next_hops) alt.fec = 'BLUE' alt.prot = 'NODE_PROTECTION' elif (alt.info == 'USE_RED' or alt.red_or_blue == 'USE_RED'): Copy_List_Items(alt.nh_list, P.red_next_hops) alt.fec = 'RED' alt.prot = 'NODE_PROTECTION' elif (alt.info == 'PRIM_NH_IS_D_OR_OP_FOR_D' or alt.info == 'PRIM_NH_IS_OP_FOR_BOTH_X_AND_Y'): if failed_intf.OUTGOING and failed_intf.INCOMING: # cut-link: if there are parallel cut links, use # the link(s) with lowest metric that are not # primary intf or None cand_alt_list = [None] min_metric = 2147483647 for intf in src.island_intf_list: if ( intf is not failed_intf and (intf.remote_node is failed_intf.remote_node)): if intf.metric < min_metric: cand_alt_list = [intf] min_metric = intf.metric elif intf.metric == min_metric: cand_alt_list.append(intf) if cand_alt_list != [None]: alt.fec = 'GREEN' alt.prot = 'PARALLEL_CUTLINK' Enyedi, et al. Expires August 19, 2016 [Page 103] Internet-Draft MRT FRR Algorithm February 2016 else: alt.fec = 'NO_ALTERNATE' alt.prot = 'NO_PROTECTION' Copy_List_Items(alt.nh_list, cand_alt_list) else: # set Z as the node to inherit blue next-hops from if alt.info == 'PRIM_NH_IS_D_OR_OP_FOR_D': Z = P.pnar1.node else: Z = P if failed_intf in Z.red_next_hops: Copy_List_Items(alt.nh_list, Z.blue_next_hops) alt.fec = 'BLUE' alt.prot = 'LINK_PROTECTION' else: assert(failed_intf in Z.blue_next_hops) Copy_List_Items(alt.nh_list, Z.red_next_hops) alt.fec = 'RED' alt.prot = 'LINK_PROTECTION' elif alt.info == 'PRIM_NH_FOR_PROXY_NODE_NOT_IN_ISLAND': if (P.pnar2 == None and src is P.pnar1.node): #MRT Island is singly connected to non-island dest alt.fec = 'NO_ALTERNATE' alt.prot = 'NO_PROTECTION' elif P.node_id in src.blue_to_green_nh_dict: # blue to P goes to failed LFIN so use red to P Copy_List_Items(alt.nh_list, P.red_next_hops) alt.fec = 'RED' alt.prot = 'LINK_PROTECTION' elif P.node_id in src.red_to_green_nh_dict: # red to P goes to failed LFIN so use blue to P Copy_List_Items(alt.nh_list, P.blue_next_hops) alt.fec = 'BLUE' alt.prot = 'LINK_PROTECTION' else: Copy_List_Items(alt.nh_list, P.blue_next_hops) alt.fec = 'BLUE' alt.prot = 'LINK_PROTECTION' elif alt.info == 'TEMP_NO_ALTERNATE': alt.fec = 'NO_ALTERNATE' alt.prot = 'NO_PROTECTION' P.alt_list.append(alt) def Run_Basic_MRT_for_One_Source(topo, src): MRT_Island_Identification(topo, src, 0, 0) Set_Island_Intf_and_Node_Lists(topo) Enyedi, et al. Expires August 19, 2016 [Page 104] Internet-Draft MRT FRR Algorithm February 2016 Set_GADAG_Root(topo,src) Sort_Interfaces(topo) Run_Lowpoint(topo) Assign_Remaining_Lowpoint_Parents(topo) Construct_GADAG_via_Lowpoint(topo) Run_Assign_Block_ID(topo) Add_Undirected_Links(topo) Compute_MRT_NH_For_One_Src_To_Island_Dests(topo,src) Store_MRT_Nexthops_For_One_Src_To_Island_Dests(topo,src) Select_Alts_For_One_Src_To_Island_Dests(topo,src) Store_Primary_and_Alts_For_One_Src_To_Island_Dests(topo,src) def Store_GADAG_and_Named_Proxies_Once(topo): for node in topo.node_list: for intf in node.intf_list: if intf.OUTGOING: intf.SIMULATION_OUTGOING = True else: intf.SIMULATION_OUTGOING = False for prefix in topo.named_proxy_dict: P = topo.named_proxy_dict[prefix] topo.stored_named_proxy_dict[prefix] = P def Run_Basic_MRT_for_All_Sources(topo): for src in topo.node_list: Reset_Computed_Node_and_Intf_Values(topo) Run_Basic_MRT_for_One_Source(topo,src) if src is topo.gadag_root: Store_GADAG_and_Named_Proxies_Once(topo) def Run_MRT_for_One_Source(topo, src): MRT_Island_Identification(topo, src, 0, 0) Set_Island_Intf_and_Node_Lists(topo) Set_GADAG_Root(topo,src) Sort_Interfaces(topo) Run_Lowpoint(topo) Assign_Remaining_Lowpoint_Parents(topo) Construct_GADAG_via_Lowpoint(topo) Run_Assign_Block_ID(topo) Add_Undirected_Links(topo) Compute_MRT_NH_For_One_Src_To_Island_Dests(topo,src) Store_MRT_Nexthops_For_One_Src_To_Island_Dests(topo,src) Select_Alts_For_One_Src_To_Island_Dests(topo,src) Store_Primary_and_Alts_For_One_Src_To_Island_Dests(topo,src) Create_Basic_Named_Proxy_Nodes(topo) Attach_Named_Proxy_Nodes(topo) Compute_MRT_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,src) Store_MRT_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,src) Enyedi, et al. Expires August 19, 2016 [Page 105] Internet-Draft MRT FRR Algorithm February 2016 Compute_Primary_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,src) Store_Primary_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,src) Select_Alts_For_One_Src_To_Named_Proxy_Nodes(topo,src) Store_Alts_For_One_Src_To_Named_Proxy_Nodes(topo,src) def Run_Prim_SPF_for_One_Source(topo,src): Normal_SPF(topo, src) Store_Primary_NHs_For_One_Source_To_Nodes(topo,src) Create_Basic_Named_Proxy_Nodes(topo) Compute_Primary_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,src) Store_Primary_NHs_For_One_Src_To_Named_Proxy_Nodes(topo,src) def Run_MRT_for_All_Sources(topo): for src in topo.node_list: Reset_Computed_Node_and_Intf_Values(topo) if src in topo.island_node_list_for_test_gr: # src runs MRT if it is in same MRT island as test_gr Run_MRT_for_One_Source(topo,src) if src is topo.gadag_root: Store_GADAG_and_Named_Proxies_Once(topo) else: # src still runs SPF if not in MRT island Run_Prim_SPF_for_One_Source(topo,src) def Write_Output_To_Files(topo,file_prefix): Write_GADAG_To_File(topo,file_prefix) Write_Both_MRTs_For_All_Dests_To_File(topo,file_prefix) Write_Alternates_For_All_Dests_To_File(topo,file_prefix) def Create_Basic_Topology_Input_File(filename): data = [[01,02,10],[02,03,10],[03,04,11],[04,05,10,20],[05,06,10], [06,07,10],[06,07,10],[06,07,15],[07,01,10],[07,51,10], [51,52,10],[52,53,10],[53,03,10],[01,55,10],[55,06,10], [04,12,10],[12,13,10],[13,14,10],[14,15,10],[15,16,10], [16,17,10],[17,04,10],[05,76,10],[76,77,10],[77,78,10], [78,79,10],[79,77,10]] with open(filename + '.csv', 'w') as topo_file: for item in data: if len(item) > 3: line = (str(item[0])+','+str(item[1])+','+ str(item[2])+','+str(item[3])+'\n') else: line = (str(item[0])+','+str(item[1])+','+ str(item[2])+'\n') topo_file.write(line) def Create_Complex_Topology_Input_File(filename): data = [[01,02,10],[02,03,10],[03,04,11],[04,05,10,20],[05,06,10], Enyedi, et al. Expires August 19, 2016 [Page 106] Internet-Draft MRT FRR Algorithm February 2016 [06,07,10],[06,07,10],[06,07,15],[07,01,10],[07,51,10], [51,52,10],[52,53,10],[53,03,10],[01,55,10],[55,06,10], [04,12,10],[12,13,10],[13,14,10],[14,15,10],[15,16,10], [16,17,10],[17,04,10],[05,76,10],[76,77,10],[77,78,10], [78,79,10],[79,77,10]] with open(filename + '.csv', 'w') as topo_file: for item in data: if len(item) > 3: line = (str(item[0])+','+str(item[1])+','+ str(item[2])+','+str(item[3])+'\n') else: line = (str(item[0])+','+str(item[1])+','+ str(item[2])+'\n') topo_file.write(line) data = [[01,0],[02,0],[03,0],[04,0],[05,0], [06,0],[07,0], [51,0],[55,0], [12,0],[13,0],[14,0],[15,0], [16,0],[17,0],[76,0],[77,0], [78,0],[79,0]] with open(filename + '.profile', 'w') as topo_file: for item in data: line = (str(item[0])+','+str(item[1])+'\n') topo_file.write(line) data = [[2001,05,100],[2001,07,120],[2001,03,130], [2002,13,100],[2002,15,110], [2003,52,100],[2003,78,100]] with open(filename + '.prefix', 'w') as topo_file: for item in data: line = (str(item[0])+','+str(item[1])+','+ str(item[2])+'\n') topo_file.write(line) def Generate_Basic_Topology_and_Run_MRT(): this_gadag_root = 3 Create_Basic_Topology_Input_File('basic_topo_input') topo = Create_Topology_From_File('basic_topo_input') res_file_base = 'basic_topo' Compute_Island_Node_List_For_Test_GR(topo, this_gadag_root) Raise_GADAG_Root_Selection_Priority(topo,this_gadag_root) Run_Basic_MRT_for_All_Sources(topo) Write_Output_To_Files(topo, res_file_base) def Generate_Complex_Topology_and_Run_MRT(): this_gadag_root = 3 Create_Complex_Topology_Input_File('complex_topo_input') Enyedi, et al. Expires August 19, 2016 [Page 107] Internet-Draft MRT FRR Algorithm February 2016 topo = Create_Topology_From_File('complex_topo_input') Add_Profile_IDs_from_File(topo,'complex_topo_input') Add_Prefix_Advertisements_From_File(topo,'complex_topo_input') Compute_Island_Node_List_For_Test_GR(topo, this_gadag_root) Add_Prefixes_for_Non_Island_Nodes(topo) res_file_base = 'complex_topo' Raise_GADAG_Root_Selection_Priority(topo,this_gadag_root) Run_MRT_for_All_Sources(topo) Write_Output_To_Files(topo, res_file_base) Generate_Basic_Topology_and_Run_MRT() Generate_Complex_Topology_and_Run_MRT() Appendix B. Constructing a GADAG using SPFs The basic idea in this method for constructing a GADAG is to use slightly-modified SPF computations to find ears. In every block, an SPF computation is first done to find a cycle from the local root and then SPF computations in that block find ears until there are no more interfaces to be explored. The used result from the SPF computation is the path of interfaces indicated by following the previous hops from the mininized IN_GADAG node back to the SPF root. To do this, first all cut-vertices must be identified and local-roots assigned as specified in Figure 12. The slight modifications to the SPF are as follows. The root of the block is referred to as the block-root; it is either the GADAG root or a cut-vertex. a. The SPF is rooted at a neighbor x of an IN_GADAG node y. All links between y and x are marked as TEMP_UNUSABLE. They should not be used during the SPF computation. b. If y is not the block-root, then it is marked TEMP_UNUSABLE. It should not be used during the SPF computation. This prevents ears from starting and ending at the same node and avoids cycles; the exception is because cycles to/from the block-root are acceptable and expected. c. Do not explore links to nodes whose local-root is not the block- root. This keeps the SPF confined to the particular block. d. Terminate when the first IN_GADAG node z is minimized. Enyedi, et al. Expires August 19, 2016 [Page 108] Internet-Draft MRT FRR Algorithm February 2016 e. Respect the existing directions (e.g. INCOMING, OUTGOING, UNDIRECTED) already specified for each interface. Mod_SPF(spf_root, block_root) Initialize spf_heap to empty Initialize nodes' spf_metric to infinity spf_root.spf_metric = 0 insert(spf_heap, spf_root) found_in_gadag = false while (spf_heap is not empty) and (found_in_gadag is false) min_node = remove_lowest(spf_heap) if min_node.IN_GADAG found_in_gadag = true else foreach interface intf of min_node if ((intf.OUTGOING or intf.UNDIRECTED) and ((intf.remote_node.localroot is block_root) or (intf.remote_node is block_root)) and (intf.remote_node is not TEMP_UNUSABLE) and (intf is not TEMP_UNUSABLE)) path_metric = min_node.spf_metric + intf.metric if path_metric < intf.remote_node.spf_metric intf.remote_node.spf_metric = path_metric intf.remote_node.spf_prev_intf = intf insert_or_update(spf_heap, intf.remote_node) return min_node SPF_for_Ear(cand_intf.local_node,cand_intf.remote_node, block_root, method) Mark all interfaces between cand_intf.remote_node and cand_intf.local_node as TEMP_UNUSABLE if cand_intf.local_node is not block_root Mark cand_intf.local_node as TEMP_UNUSABLE Initialize ear_list to empty end_ear = Mod_SPF(spf_root, block_root) y = end_ear.spf_prev_hop while y.local_node is not spf_root add_to_list_start(ear_list, y) y.local_node.IN_GADAG = true y = y.local_node.spf_prev_intf if(method is not hybrid) Set_Ear_Direction(ear_list, cand_intf.local_node, end_ear,block_root) Clear TEMP_UNUSABLE from all interfaces between cand_intf.remote_node and cand_intf.local_node Enyedi, et al. Expires August 19, 2016 [Page 109] Internet-Draft MRT FRR Algorithm February 2016 Clear TEMP_UNUSABLE from cand_intf.local_node return end_ear Figure 31: Modified SPF for GADAG construction Assume that an ear is found by going from y to x and then running an SPF that terminates by minimizing z (e.g. y<->x...q<->z). Now it is necessary to determine the direction of the ear; if y << z, then the path should be y->x...q->z but if y >> z, then the path should be y<- x...q<-z. In Section 5.5, the same problem was handled by finding all ears that started at a node before looking at ears starting at nodes higher in the partial order. In this GADAG construction method, using that approach could mean that new ears aren't added in order of their total cost since all ears connected to a node would need to be found before additional nodes could be found. The alternative is to track the order relationship of each node with respect to every other node. This can be accomplished by maintaining two sets of nodes at each node. The first set, Higher_Nodes, contains all nodes that are known to be ordered above the node. The second set, Lower_Nodes, contains all nodes that are known to be ordered below the node. This is the approach used in this GADAG construction method. Enyedi, et al. Expires August 19, 2016 [Page 110] Internet-Draft MRT FRR Algorithm February 2016 Set_Ear_Direction(ear_list, end_a, end_b, block_root) // Default of A_TO_B for the following cases: // (a) end_a and end_b are the same (root) // or (b) end_a is in end_b's Lower Nodes // or (c) end_a and end_b were unordered with respect to each // other direction = A_TO_B if (end_b is block_root) and (end_a is not end_b) direction = B_TO_A else if end_a is in end_b.Higher_Nodes direction = B_TO_A if direction is B_TO_A foreach interface i in ear_list i.UNDIRECTED = false i.INCOMING = true i.remote_intf.UNDIRECTED = false i.remote_intf.OUTGOING = true else foreach interface i in ear_list i.UNDIRECTED = false i.OUTGOING = true i.remote_intf.UNDIRECTED = false i.remote_intf.INCOMING = true if end_a is end_b return // Next, update all nodes' Lower_Nodes and Higher_Nodes if (end_a is in end_b.Higher_Nodes) foreach node x where x.localroot is block_root if end_a is in x.Lower_Nodes foreach interface i in ear_list add i.remote_node to x.Lower_Nodes if end_b is in x.Higher_Nodes foreach interface i in ear_list add i.local_node to x.Higher_Nodes else foreach node x where x.localroot is block_root if end_b is in x.Lower_Nodes foreach interface i in ear_list add i.local_node to x.Lower_Nodes if end_a is in x.Higher_Nodes foreach interface i in ear_list add i.remote_node to x.Higher_Nodes Figure 32: Algorithm to assign links of an ear direction A goal of this GADAG construction method is to find the shortest cycles and ears. An ear is started by going to a neighbor x of an IN_GADAG node y. The path from x to an IN_GADAG node is minimal, Enyedi, et al. Expires August 19, 2016 [Page 111] Internet-Draft MRT FRR Algorithm February 2016 since it is computed via SPF. Since a shortest path is made of shortest paths, to find the shortest ears requires reaching from the set of IN_GADAG nodes to the closest node that isn't IN_GADAG. Therefore, an ordered tree is maintained of interfaces that could be explored from the IN_GADAG nodes. The interfaces are ordered by their characteristics of metric, local loopback address, remote loopback address, and ifindex, based on the Interface_Compare function defined in Figure 14. This GADAG construction method ignores interfaces picked from the ordered list that belong to the block root if the block in which the interface is present already has an ear that has been computed. This is necessary since we allow at most one incoming interface to a block root in each block. This requirement stems from the way next-hops are computed as was seen in Section 5.7. After any ear gets computed, we traverse the newly added nodes to the GADAG and insert interfaces whose far end is not yet on the GADAG to the ordered tree for later processing. Finally, cut-links are a special case because there is no point in doing an SPF on a block of 2 nodes. The algorithm identifies cut- links simply as links where both ends of the link are cut-vertices. Cut-links can simply be added to the GADAG with both OUTGOING and INCOMING specified on their interfaces. add_eligible_interfaces_of_node(ordered_intfs_tree,node) for each interface of node if intf.remote_node.IN_GADAG is false insert(intf,ordered_intfs_tree) check_if_block_has_ear(x,block_id) block_has_ear = false for all interfaces of x if ( (intf.remote_node.block_id == block_id) && intf.remote_node.IN_GADAG ) block_has_ear = true return block_has_ear Construct_GADAG_via_SPF(topology, root) Compute_Localroot (root,root) Assign_Block_ID(root,0) root.IN_GADAG = true add_eligible_interfaces_of_node(ordered_intfs_tree,root) while ordered_intfs_tree is not empty cand_intf = remove_lowest(ordered_intfs_tree) if cand_intf.remote_node.IN_GADAG is false if L(cand_intf.remote_node) == D(cand_intf.remote_node) // Special case for cut-links Enyedi, et al. Expires August 19, 2016 [Page 112] Internet-Draft MRT FRR Algorithm February 2016 cand_intf.UNDIRECTED = false cand_intf.remote_intf.UNDIRECTED = false cand_intf.OUTGOING = true cand_intf.INCOMING = true cand_intf.remote_intf.OUTGOING = true cand_intf.remote_intf.INCOMING = true cand_intf.remote_node.IN_GADAG = true add_eligible_interfaces_of_node( ordered_intfs_tree,cand_intf.remote_node) else if (cand_intf.remote_node.local_root == cand_intf.local_node) && check_if_block_has_ear(cand_intf.local_node, cand_intf.remote_node.block_id)) /* Skip the interface since the block root already has an incoming interface in the block */ else ear_end = SPF_for_Ear(cand_intf.local_node, cand_intf.remote_node, cand_intf.remote_node.localroot, SPF method) y = ear_end.spf_prev_hop while y.local_node is not cand_intf.local_node add_eligible_interfaces_of_node( ordered_intfs_tree, y.local_node) y = y.local_node.spf_prev_intf Figure 33: SPF-based method for GADAG construction Appendix C. Constructing a GADAG using a hybrid method The idea of this method is to combine the salient features of the lowpoint inheritance and SPF methods. To this end, we process nodes as they get added to the GADAG just like in the lowpoint inheritance by maintaining a stack of nodes. This ensures that we do not need to maintain lower and higher sets at each node to ascertain ear directions since the ears will always be directed from the node being processed towards the end of the ear. To compute the ear however, we resort to an SPF to have the possibility of better ears (path lentghs) thus giving more flexibility than the restricted use of lowpoint/dfs parents. Regarding ears involving a block root, unlike the SPF method which ignored interfaces of the block root after the first ear, in the hybrid method we would have to process all interfaces of the block root before moving on to other nodes in the block since the direction Enyedi, et al. Expires August 19, 2016 [Page 113] Internet-Draft MRT FRR Algorithm February 2016 of an ear is pre-determined. Thus, whenever the block already has an ear computed, and we are processing an interface of the block root, we mark the block root as unusable before the SPF run that computes the ear. This ensures that the SPF terminates at some node other than the block-root. This in turn guarantees that the block-root has only one incoming interface in each block, which is necessary for correctly computing the next-hops on the GADAG. As in the SPF gadag, bridge ears are handled as a special case. The entire algorithm is shown below in Figure 34 find_spf_stack_ear(stack, x, y, xy_intf, block_root) if L(y) == D(y) // Special case for cut-links xy_intf.UNDIRECTED = false xy_intf.remote_intf.UNDIRECTED = false xy_intf.OUTGOING = true xy_intf.INCOMING = true xy_intf.remote_intf.OUTGOING = true xy_intf.remote_intf.INCOMING = true xy_intf.remote_node.IN_GADAG = true push y onto stack return else if (y.local_root == x) && check_if_block_has_ear(x,y.block_id) //Avoid the block root during the SPF Mark x as TEMP_UNUSABLE end_ear = SPF_for_Ear(x,y,block_root,hybrid) If x was set as TEMP_UNUSABLE, clear it cur = end_ear while (cur != y) intf = cur.spf_prev_hop prev = intf.local_node intf.UNDIRECTED = false intf.remote_intf.UNDIRECTED = false intf.OUTGOING = true intf.remote_intf.INCOMING = true push prev onto stack cur = prev xy_intf.UNDIRECTED = false xy_intf.remote_intf.UNDIRECTED = false xy_intf.OUTGOING = true xy_intf.remote_intf.INCOMING = true return Construct_GADAG_via_hybrid(topology,root) Enyedi, et al. Expires August 19, 2016 [Page 114] Internet-Draft MRT FRR Algorithm February 2016 Compute_Localroot (root,root) Assign_Block_ID(root,0) root.IN_GADAG = true Initialize Stack to empty push root onto Stack while (Stack is not empty) x = pop(Stack) for each interface intf of x y = intf.remote_node if y.IN_GADAG is false find_spf_stack_ear(stack, x, y, intf, y.block_root) Figure 34: Hybrid GADAG construction method Authors' Addresses Gabor Sandor Enyedi Ericsson Konyves Kalman krt 11 Budapest 1097 Hungary Email: Gabor.Sandor.Enyedi@ericsson.com Andras Csaszar Ericsson Konyves Kalman krt 11 Budapest 1097 Hungary Email: Andras.Csaszar@ericsson.com Alia Atlas Juniper Networks 10 Technology Park Drive Westford, MA 01886 USA Email: akatlas@juniper.net Enyedi, et al. Expires August 19, 2016 [Page 115] Internet-Draft MRT FRR Algorithm February 2016 Chris Bowers Juniper Networks 1194 N. Mathilda Ave. Sunnyvale, CA 94089 USA Email: cbowers@juniper.net Abishek Gopalan University of Arizona 1230 E Speedway Blvd. Tucson, AZ 85721 USA Email: abishek@ece.arizona.edu Enyedi, et al. Expires August 19, 2016 [Page 116]