Network Working Group Luca Martini Internet Draft Expiration Date: March 2006 Cisco Systems Inc. September 2005 IANA Allocations for pseudo Wire Edge to Edge Emulation (PWE3) draft-ietf-pwe3-iana-allocation-12.txt Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/1id-abstracts.html The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract This document pre-allocates the fixed Pseudo-wire identifier , and other fixed protocol values for protocols defined primarily in the pseudo wire edge to edge working group. ( PWE3 ) Detailed IANA allocation instructions are also included in this document. Martini [Page 1] Internet Draft draft-ietf-pwe3-iana-allocation-12.txt September 2005 Table of Contents 1 Specification of Requirements .......................... 2 2 IANA Considerations .................................... 2 2.1 Pseudowire Type ........................................ 2 2.2 Interface Parameters Sub-TLV type ...................... 3 2.3 Attachment Identifiers ................................. 4 2.3.1 Attachment Individual Identifier Type .................. 4 2.3.2 Attachment Group Identifier (AGI) Type ................. 5 2.4 Pseudo Wire Status ..................................... 5 3 Security Considerations ................................ 6 4 Full Copyright Statement ............................... 6 5 Intellectual Property Statement ........................ 6 6 Normative References ................................... 7 7 Author Information ..................................... 7 1. Specification of Requirements The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 2. IANA Considerations Unless otherwise noted in this document, the value of 0 is reserved, and MUST not be used. 2.1. Pseudowire Type IANA needs to set up a registry of "Pseudowire Type". These are 15- bit values. PW Type values 1 through 30 are specified in this document, PW Type values 31 through 1024 are to be assigned by IANA, using the "Expert Review" policy defined in [RFC2434]. PW Type values 1025 through 4096, and 32768 are reserved for future use, and are not to be allocated by IANA. PW Type values 4097 through 32767 are reserved for vendor proprietary extensions and are to be assigned by IANA, using the "First Come First Served" policy defined in RFC2434. A Pseudowire Type description of up to 65 characters is required for any assignment from this registry. Martini [Page 2] Internet Draft draft-ietf-pwe3-iana-allocation-12.txt September 2005 Initial Pseudowire type value allocations are specified below: PW type Description 0x0001 Frame Relay DLCI ( Martini Mode ) 0x0002 ATM AAL5 SDU VCC transport 0x0003 ATM transparent cell transport 0x0004 Ethernet Tagged Mode 0x0005 Ethernet 0x0006 HDLC 0x0007 PPP 0x0008 SONET/SDH Circuit Emulation Service Over MPLS(CEM) [Note1] 0x0009 ATM n-to-one VCC cell transport 0x000A ATM n-to-one VPC cell transport 0x000B IP Layer2 Transport 0x000C ATM one-to-one VCC Cell Mode 0x000D ATM one-to-one VPC Cell Mode 0x000E ATM AAL5 PDU VCC transport 0x000F Frame-Relay Port mode 0x0010 SONET/SDH Circuit Emulation over Packet (CEP) 0x0011 Structure-agnostic E1 over Packet (SAToP) 0x0012 Structure-agnostic T1 (DS1) over Packet (SAToP) 0x0013 Structure-agnostic E3 over Packet (SAToP) 0x0014 Structure-agnostic T3 (DS3) over Packet (SAToP) 0x0015 CESoPSN basic mode 0x0016 TDMoIP AAL1 Mode 0x0017 CESoPSN TDM with CAS 0x0018 TDMoIP AAL2 Mode 0x0019 Frame Relay DLCI 0x001A cTCP (RFC1144) Transport Header-compressed Packets 0x001B IPHC (RFC2507) Transport Header-compressed Packets 0x001C cRTP (RFC2508) Transport Header-compressed Packets 0x001D ROHC (RFC3095) Transport Header-compressed Packets 0x001E eCRTP (RFC3545) Transport Header-compressed Packets Note 1: This PW type is grandfathered for a historical protocol. The recommended standards-track protocol to use is CEP (PW type 0x0010). 2.2. Interface Parameters Sub-TLV type IANA needs to set up a registry of "Pseudowire Interface Parameter Sub-TLV types". These are 8 bit values. Sub-TLV types 1 through 12 are specified in this document. Sub-TLV types 13 through 64 are to be assigned by IANA, using the "Expert Review" policy defined in RFC2434. Sub-TLV types 65 through 127, and 255 are reserved for future use, and are not to be allocated by IANA. Sub-TLV types Martini [Page 3] Internet Draft draft-ietf-pwe3-iana-allocation-12.txt September 2005 values 128 through 254 are reserved for vendor proprietary extensions and are to be assigned by IANA, using the "First Come First Served" policy defined in RFC2434. Any assignments requested from this registry require a description up to 54 characters. Furthermore a length specified as follows: - A decimal integer - Text as follows:"up to X", where X is a decimal integer - Up to 3 different decimal integers. is also required for assignment from this registry. Initial Pseudowire Interface Parameter Sub-TLV type allocations are specified below: Parameter ID Length Description 0x01 4 Interface MTU in octets 0x02 4 Maximum Number of concatenated ATM cells 0x03 up to 82 Optional Interface Description string 0x04 4 CEP/TDM Payload Bytes 0x05 4 CEP options 0x06 4 Requested VLAN ID 0x07 6 CEP/TDM bit-rate 0x08 4 Frame-Relay DLCI Length 0x09 4 Fragmentation indicator 0x0A 4 FCS retention indicator 0x0B 4/8/12 TDM options 0x0C 4 VCCV parameter Note that the Length field is defined as the length of the Sub-TLV including the Sub-TLV type and length field itself. 2.3. Attachment Identifiers 2.3.1. Attachment Individual Identifier Type IANA needs to set up a registry of "Attachment Individual Identifier (AII) Type". These are 8-bit values. AII Type value 1 is defined in this document. AII Type values 2 through 64 are to be assigned by IANA using the "Expert Review" policy defined in RFC2434. AII Type values 65 through 127, and 255 are reserved for future use, and are not to be allocated by IANA. AII types values 128 through 254 are reserved for vendor proprietary extensions and are to be assigned by IANA, using the "First Come First Served" policy defined in RFC2434. Any assignments requested from this registry require a description up to 54 characters. Furthermore a length specified as follows: Martini [Page 4] Internet Draft draft-ietf-pwe3-iana-allocation-12.txt September 2005 - A decimal integer - Text as follows:"up to X", where X is a decimal integer - the word "Variable" Initial Attachment Individual Identifier (AII) Type allocations are specified below: AII Type Length Description 0x014 A 32 bit unsigned number local identifier. 2.3.2. Attachment Group Identifier (AGI) Type IANA needs to set up a registry of "Attachment Group Identifier (AGI) Type". These are 8-bit values. AGI Type value 1 is defined in this document. AGI Type values 2 through 64 are to be assigned by IANA using the "Expert Review" policy defined in RFC2434. AGI Type values 65 through 127, and 255 are reserved for future use, and are not to be allocated by IANA. AGI types values 128 through 254 are reserved for vendor proprietary extensions and are to be assigned by IANA, using the "First Come First Served" policy defined in RFC2434. Any assignments requested from this registry require a description up to 54 characters. Furthermore a length specified as follows: - A decimal integer - Text as follows:"up to X", where X is a decimal integer - the word "Variable" Initial Attachment Group Identifier (AGI) Type allocations are specified below: AGI Type Length Description 0x018 A route distinguisher (RD) as defined in rfc2547 2.4. Pseudo Wire Status IANA needs to set up a registry of "Pseudowire Status Codes". These are bitstrings of length 32. Status bits 0 to 4 are defined in this document. Status bits 5 to 31 are to be assigned by IANA using the "Expert Review" policy defined in RFC2434. Any requests for allocation from this registry must include a description up to 65 characters. Initial Pseudowire Status Codes value allocations are as follows: Bit MaskDescription 0x00000000 - Pseudo Wire forwarding ( clear all failures ) 0x00000001 - Pseudo Wire Not Forwarding 0x00000002 - Local Attachment Circuit ( ingress ) Receive Fault 0x00000004 - Local Attachment Circuit ( egress ) Transmit Fault Martini [Page 5] Internet Draft draft-ietf-pwe3-iana-allocation-12.txt September 2005 0x00000008 - Local PSN-facing PW ( ingress ) Receive Fault 0x00000010 - Local PSN-facing PW ( egress ) Transmit Fault 3. Security Considerations This document specifies only fixed identifiers, and not the protocols used to carry the encapsulated packets across the network. Each such protocol may have its own set of security issues, but those issues are not affected by the identifiers specified herein. 4. Full Copyright Statement Copyright (C) The Internet Society (2005). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. 5. Intellectual Property Statement The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any Martini [Page 6] Internet Draft draft-ietf-pwe3-iana-allocation-12.txt September 2005 copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf- ipr@ietf.org. 6. Normative References [RFC2434] " Guidelines for Writing an IANA Considerations Section in RFCs", BCP26, October 1998. 7. Author Information Luca Martini Cisco Systems, Inc. 9155 East Nichols Avenue, Suite 400 Englewood, CO, 80112 e-mail: lmartini@cisco.com Martini [Page 7]