Internet Draft Document: T. Zseby Expires: April 2003 Fraunhofer FOKUS M. Molina NEC Europe Ltd. F. Raspall NEC Europe Ltd. October 2002 Sampling and Filtering Techniques for IP Packet Selection Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract This document describes sampling and filtering techniques for IP packet selection. It introduces information models for packet sampling, for packet filtering and for combinations of methods. The information models describe what information has to be specified in order to describe the method. This information is used for configuring the selection technique in measurement processes and for reporting the technique in use to the measurement data collection process. The document first suggests some terminology, then it describes in detail packet sampling and packet filtering techniques and their parameters. It also describes how these two techniques can be combined to build more elaborate packet selectors. Finally, it introduces information models for the most common sampling and filtering techniques. Zseby, Molina, Raspall Expires April 2003 [Page 1] Internet Draft Techniques for IP Packet Selection August 2002 Table of Contents 1. Introduction.................................................2 2. Terminology..................................................3 3. Scope and Deployment of Packet Selection Techniques..........4 3.1 Sampling.....................................................5 3.2 Filtering....................................................6 4. Sampling Methods.............................................6 4.1 Sampling Algorithm...........................................6 4.1.1 Systematic Sampling..........................................6 4.1.2 Random Sampling..............................................6 5. Sampling Parameters..........................................7 5.1 Parameters for systematic sampling...........................7 5.2 Parameters for random sampling...............................7 6. Information Model Sampling Techniques........................8 7. Filtering....................................................9 7.1 Filtering operating directly on some of the packetÆs bits....9 7.2 Filtering considering router reaction or router state.......10 8. Information Model for Filtering Techniques..................10 9. Composite Techniques........................................12 9.1 Cascaded filtering->sampling or sampling->filtering.........13 9.2 Stratified Sampling.........................................13 10. Security Considerations.....................................14 11. References..................................................14 12. Author's Addresses..........................................15 13. Full Copyright Statement....................................15 1. Introduction Increasing data rates and growing measurement demands increase the requirements for data collection resources. For measurement scenarios in backbone networks it is often required to measure whole traffic aggregates instead of single flows. Furthermore some measurement methods require the capturing of packet headers or even parts of the payload. All this can lead to an overwhelming amount of measurement data, resulting in high demands regarding resources for metering, storage, transport and post processing. In some cases specialized hardware helps to fulfill these demands but on the other hand increases the costs for providing the measurement. Since measurements are mainly a supporting functionality for the service provisioning, measurement costs usually should be limited to a small fraction of the costs of the network service provisioning itself. Therefore a reduction of the measurement result data is crucial to prevent the depletion of the available (i.e. the affordable) resources. Such a reduction can be achieved by a reasonable deployment of packet selection techniques, that sample a subset of the packets while still allowing reliable measurements, or filter out all the packet not interesting for the measurement itself. Packet selection helps to prevent an exhaustion of resources and to limit the measurement costs. Examples for Zseby, Molina, Raspall Expires April 2003 [Page 2] Internet Draft Techniques for IP Packet Selection August 2002 applications that benefit from packet selection are given in [DuGG02]. 2. Terminology IP Packet Selection Process An IP packet selection process takes IP packets or parts of IP packets (e.g. header) as input and extracts a subset of these packets by applying a selection function. Filtering Filtering selects a subset of packets by applying deterministic functions on parts of the packet content like header fields or parts of the payload. Filtering techniques can also be used to emulate a (pseudo)random selection of packets with a given probability p. A filtering process needs to process the packet (look at packet header and/or payload) in order to make the selection decision. Sampling Sampling selects a subset of packets by applying deterministic or random functions on the (temporal or spatial) packet position or by performing (pseudo)random calculations per packet. This can be for example selecting every nth packet (deterministic function on packet position)or selecting a packet that arrived at the metering process in accordance to the output of a random function (like flipping a coin per packet). Sampling does not work on packet content. That means, in contrast to filtering, a sampling process does not need to process the packet in order to make the selection decision. Hash function The computation of an M bit string starting from an N bit string. In this context, the N starting bits are some of the bits of a packet header and/or payload. Hash selection range A subset of the M bit computed with a hash function for which an Indicator Function has a value of 1. Stream A packet stream is the sequence of packets used as input for a packet selection process. If multiple packet selectors are applied subsequently, the output stream of one selector forms the input stream for the succeeding selector. If the first selector was a sampling process, the packets in the stream usually do not have common properties by which they can be distinguished from the not selected packets. Therefore we define here the term stream instead of flow, which is defined as set of packets with common properties [QuZC02]. If the term flow is used throughout the text, the flow definition in [QuZC02] applies. Zseby, Molina, Raspall Expires April 2003 [Page 3] Internet Draft Techniques for IP Packet Selection August 2002 Metering process see definition in [QuZC02] Sample size The sample size denotes the number of packets in the sample. Selection function Function that determines whether an IP packet is selected or not. Sampling probability The probability with which one element is selected as part of the sample. Sampling ratio The ratio between the sample size and the number of packets composing the input stream of a packet sampling process. 3. Scope and Deployment of Packet Selection Techniques The selection technique used to select a subset of packets out of all those crossing an observation point depends on the purpose (application) for which measurement is performed. If the main purpose of an application is to infer some characteristic of the whole set of crossing packets without processing them all (thus reducing the computation load) then we call the used selection technique ôsamplingö. In principle, with sampling the content of the packet is not relevant for the packet selection: what matters is only that the selected sample has a distribution of the characteristic to infer similar to the one of the parent population, so that it can be estimated reliably. The sampling decision may be based on the temporal or spatial position of the packet in the packet stream, or may depend on a (pseudo)random number extraction or calculation. On the contrary, if the application needs to consider all the packets having some common property, then we call the selection technique ôfilteringö. The property can be directly derived by some computation on the packet content, or depend on the treatment given by the router to the packet. We conclude that sampling does not consider packet content, and can depend on packet position or on (pseudo)random decisions, while filtering depends on packet content, but never depends on packet position or on (pseudo)random decisions. Note that a common technique to select packets is to compute a hash function on some bits of the packet header and/or content and to select it if the result falls in a certain selection range. Since hashing is a deterministic operation, it is a powerful mean to ensure that the same packets are selected at multiple measurement points. Depending on the chosen input bits, on the hash function and on the selection range, this technique could also be used to emulate the random selection of packets with a given probability p. However, Zseby, Molina, Raspall Expires April 2003 [Page 4] Internet Draft Techniques for IP Packet Selection August 2002 due to its intrinsically deterministic nature, we prefer to classify hashing as a filtering technique. The introduced classification is mainly useful for the definition of an information model describing ôprimitiveö selection techniques. More complex selection techniques may then be described through the composition of cascaded sampling and filtering operations. For example, a packet selection that weights the selection probability on the basis of the packet length can be described as a set of filter/sampling cascades. However, this descriptive approach is not intended to be rigid: if a common and consolidated selection practice turns out to be too complex to be described as a composition of the mentioned building blocks, an ad hoc description can be specified instead. We consider packet selectors as part of an IPFIX metering process which also can use the IPFIX exporting process. This is expressed as association to one or more IPFIX processes. 3.1 Sampling The deployment of sampling techniques aims at the provisioning of information about a specific characteristic of the parent population at a lower cost than a full census would demand. In order to plan a suitable sampling strategy it is therefore crucial to determine the needed type of information and the desired degree of accuracy in advance. First of all it is important to know the type of metric that should be estimated. The metric of interest can range from simple packet counts [JePP92] up to the estimation of whole distributions of flow characteristics (e.g. packet sizes)[ClPB93]. Secondly, the required accuracy of the information and with this, the confidence that is aimed at, should be known in advance. For instance for usage-based accounting the required confidence for the estimation of packet counters can depend on the monetary value that corresponds to the transfer of one packet. That means that a higher confidence could be required for expensive packet flows (e.g. premium IP service) than for cheaper flows (e.g. best effort). The accuracy requirements for validating a previously agreed quality can also vary extremely with the customer demands. These requirements are usually determined by the service level agreement (SLA). Sampling is considered as part of the metering process. It can be applied at different functions of the metering process. In the following we consider a measured IP packet with its observation point and timestamp as basis elements of the parent population. The sampling method and the parameters in use must be clearly communicated to all applications that use the measurement data. Only Zseby, Molina, Raspall Expires April 2003 [Page 5] Internet Draft Techniques for IP Packet Selection August 2002 with this a correct interpretation of the measurement results can be ensured. 3.2 Filtering Packet filtering can be done for a wide variety of purposes e.g. for security, SLA enforcing, accounting. Depending on the type of filtering, it can be applied in different parts of the metering process. The role of filtering, as the word itself suggest, is to separate all the packets having a certain property from those not having it. A distinguishing characteristic from sampling is that the property never depends on the packet position in time or in the space, or on a random process. However, hash based filtering may be used to emulate a random selection. 4. Sampling Methods Sampling Methods can be characterized by the sampling algorithm, the trigger type used for starting a sampling interval and the length of the sampling interval. These parameters are described here in detail. 4.1 Sampling Algorithm The sampling algorithm describes the basic process for selection of samples. In accordance to [AmCa89] and [ClPB93] we define the following basic sampling processes: 4.1.1 Systematic Sampling Systematic sampling describes the process of selecting the starting points and the duration of the selection intervals according to a deterministic function. This can be for instance the periodic selection of every n-th element of a trace but also the selection of all packets that arrive at pre-defined points in time. Even if the selection process does not follow a periodic function (e.g. if the time between the sampling intervals varies over time) we consider this as systematic sampling as long as the selection is deterministic. The use of systematic sampling always involves the risk of biasing the results. If the systematics in the sampling process resembles systematics in the observed stochastic process (occurrence of the characteristic of interest in the network), there is a high probability that the estimation will be biased. Systematics (e.g. periodic repetition of an event) in the observed process might not be known of in advance. 4.1.2 Random Sampling Random sampling selects the starting points of the sampling intervals in accordance to a random process. The selection of elements are independent experiments. With this, unbiased estimations can be achieved. In contrast to systematic sampling, Zseby, Molina, Raspall Expires April 2003 [Page 6] Internet Draft Techniques for IP Packet Selection August 2002 random sampling requires the generation of random numbers. One can differentiate two methods of random sampling: n-out-of-N sampling In n-out-of-N sampling n elements are selected out of the parent population that consists of N elements. One example would be to generate random numbers and select all packets which have a packet position equal to one of the random numbers. For this kind of sampling the sample size is fixed. Probabilistic sampling (see also [DuGG02]) In probabilistic sampling the decision whether an element is selected or not is made in accordance to a pre-defined selection probability. An example would be to flip a coin for each packet and select all packets for which the coin showed the head. For this kind of sampling the sample size can vary for different trials. The selection probability is not necessarily the same for each packet. 5. Sampling Parameters The decision whether to select a packet or not is based on a function which is performed when the packet arrives at the sampling process. The sampling function can consist of a (pseudo)random calculation or of a function that take the packet position(temporal or spatial) into account. The parameters of these functions that are not derived from the packet are called sampling parameters. 5.1 Parameters for systematic sampling For systematic sampling the deterministic function which is used for the packet selection needs to be given. For periodic sampling the start of the first selection interval, the length of the selection interval (given in number of packets or as time duration) and the spacing between selection intervals needs to be specified. <-- interval length = 7 --> <-- spacing = 5 _-> Packet position: 1 2 3 4 5 6 7 8 9 10 11 12 13.. The packets in the sample will be: 1,2,3,4,5,6,7, 13,... Selecting every x-th packet would be a special case with selection interval=1 and spacing=x-1. 5.2 Parameters for random sampling For random n-out-of-N sampling only the sample size n needs to be specified. This can be done either as an absolute number or as fraction of the parent population n/N. For probabilistic sampling the selection probability p needs to be specified. If the selection probability depends on other parameters Zseby, Molina, Raspall Expires April 2003 [Page 7] Internet Draft Techniques for IP Packet Selection August 2002 (e.g. packet content), the function that expresses this dependency has to be specified. 6. Information Model Sampling Techniques In this section we define the information models for most common sampling techniques. Here the selection function is pre-defined and given by the selector ID. Sampler Description: SELECTOR_ID SELECTOR_TYPE SELECTOR_PARAMETERS OPERATING_TIME ASSOCIATIONS Where: SELECTOR_ID: Unique ID for the packet sampler. The ID can be calculated under consideration of the ASSOCIATIONS and a local ID. SELECTOR_TYPE Description: For sampling processes the SELECTOR TYPE defines what sampling algorithm is used. Values: n out of N | Systematic Time Based (equally spaced)| Systematic Position Based (equally spaced)| Probabilistic [Remark: further sampling schemes will be added here] SELECTOR_PARAMETERS Description: For sampling processes the SELECTOR PARAMETERS define the input parameters for the process. Interval length in systematic sampling means, that all packets that arrive in this interval are selected. The spacing parameter defines the spacing in time or number of packets between the end of one sampling interval and the start of the next succeeding interval. Case n out of N - List of n sampling positions in an array of N positions Case STB: - Interval length (in usec), Spacing (in usec) Case SPB - Interval length(in packets), Spacing (in packets) Case Probabilistic(with equal probability per packet) - Sampling probability p OPERATING_TIME Description: The OPERATING_TIME parameter describes the start/stop time of sampling process. List elements must not overlap. The start Zseby, Molina, Raspall Expires April 2003 [Page 8] Internet Draft Techniques for IP Packet Selection August 2002 time of the first element can be omitted, meaning ôfrom nowö. The end time of the last element can be omitted, meaning ôuntil sampler is removedö. Values: List of (Start time, End time) ASSOCIATIONS Description: The ASSOCIATIONS field describes the observation point and the IPFIX processes to which the packet selector is associated. The STREAM ID denotes the origin of the data stream that is input to the selection function. It can be the observation point directly or the ID of another selector. With this it is possible to define combined schemes. If the STREAM ID contains IDs from other selectors, one can derive the original observation point from the selector definitions of these specified selectors. Values: With STREAM ID: Observation point ID | List of SELECTOR_IDs 7. Filtering As pointed out in section 3, the main difference between sampling and filtering is that filtering never depends on the temporal or spatial position of packets. We introduce two classes of filters. In the first one, the property can be directly derived by applying a function on some bits of the packet, while in the second one the property depends on router state or on the routerÆs reaction to a particular packet. The filters of the first class should be able to operate at full line rate, while some of the ones of the second may need to be preceded by a sampling function (e.g. because they involve access to router state). [Discussion needed on router-state based filtering] 7.1 Filtering operating directly on some of the packetÆs bits These filters functionally operate as follow: - They select some bits of the packet (not or not only necessarily those of the header). - They apply a function on the selected bits. The function can be as simple as the identity function (i.e. this step is logically skipped), or as complex as a hash function. - They feed the result of the function into an indicator function, that returns a ôselect/do not selectö result. Examples of filters of this class are filters that select packets on the basis of the matching of some of the header fields with a (possibly masked) pre defined value, filters that select the packets that have some header field value falling within a predefined range, or filters that select some header fields and/or a portion of the payload, apply a hash function and then select the packet if the Zseby, Molina, Raspall Expires April 2003 [Page 9] Internet Draft Techniques for IP Packet Selection August 2002 results is in the hash selection range. Note that in the latter case, the selected bits may not be the only one forming the input of the hash function. For example, a ôsecretö bit sequence could be appended to the selected bits in order to make it harder for an attacker to forge packets being either always or never selected. An implementation isnÆt constrained to apply exactly all these steps or in this sequence, provided that the result is equivalent to a logical function doing it. 7.2 Filtering considering router reaction or router state This class of filters select a packet on the basis of the following conditions), possibly combined with the AND, OR or NOT operators. - Ingress interface it is coming from equal to a specified value - Egress interface it is routed to equal to a specified value - Packet violated acl on the router - Failed rpf - Failed rsvp - No route found for the packet - Origin AS equal to a specified value or within a specified range - Destination AS equal to a specified value or within a specified range 8. Information Model for Filtering Techniques In this section we define the information models for most common filtering techniques. The information model structure closely parallels the one presented for the sampling techniques. Filter Description: SELECTOR_ID SELECTOR_TYPE SELECTOR_PARAMETERS OPERATING_TIME ASSOCIATIONS Where: SELECTOR_ID: Unique ID for the packet filter. The ID can be calculated under consideration of the ASSOCIATIONS and a local ID. SELECTOR_TYPE Description: For filtering processes the SELECTOR TYPE defines what filtering type is used. Values: Matching | Hashing | Router_state SELECTOR_PARAMETERS Zseby, Molina, Raspall Expires April 2003 [Page 10] Internet Draft Techniques for IP Packet Selection August 2002 Description: For filtering processes the SELECTOR PARAMETERS define formally the common property of the packet being filtered. For the filters of type Matching and Hashing the definitions have a lot of points in common. Values: Case Matching -
- - -
- - - - - Notes to Case Matching: - The filter can be defined for the header part only, for the payload part only or for both. In the latter case the matching must be an AND of the two. - The bit specification, for the header part, can be specified for ipv4 or ipv6 only, or both - In case of ipv4, the bit specification is a sequence of 20 Hexadecimal numbers [00,FF] specifying a 20 bytes bitmask to be applied to the header - In case of ipv6, it is a sequence of 40 Hexadecimal numbers [00,FF] specifying a 40 bytes bitmask to be applied to the header - The bit specification, for the payload part, is a sequence of Hexadecimal numbers [00,FF] specifying the bitmask to be applied to the first N bytes of the payload, as specified by the previous field. In case the Hexadecimal number sequence is longer then N, only the first N numbers are considered. - In case the payload is shorter than N, the packet will not match the filter Other options, like padding with zeros, may be considered in the future. - The selection interval specification is a list of non overlapping intervals [intv_begin, intv_end] where intv_begin, intv_end are bit strings of length 20*8 (ipv4 case), 40*8 (ipv6 case), N*8 (payload case). - A filter cannot be defined on the options field of the ipv4 header, neither on stacked headers of ipv6. - This specification doesnÆt preclude the future definition of a high level syntax for defining in a concise way bit selection and matching rules in a more human readable form (e.g. ôTCP port in [2000,3000]ö). The requirement is that such a syntax can be univoquely compiled into the one defined above Case Hashing: -
- -
Zseby, Molina, Raspall Expires April 2003 [Page 11] Internet Draft Techniques for IP Packet Selection August 2002 - - - - - Hashing function specification (includes length of hash function output M) - Selection interval specification, as a list of non overlapping intervals [start value, end value] where value is in [0,2^M-1] Notes to Case Hashing: - On Input bit specifications fields, the same notes on bit specifications of the Matching case reported above apply Case Router State: - Ingress interface it is coming from equal to a specified value - Egress interface it is routed to equal to a specified value - Packet violated acl on the router - Failed rpf - Failed rsvp - No route found for the packet - Origin AS equal to a specified value or within a specified range - Destination AS equal to a specified value or within a specified range Note to Case Router State: - All Router state entries can be linked by AND, OR, NOT operators OPERATING_TIME Description: The OPERATING_TIME parameter describes the start/stop time of filtering process. List elements must not overlap. The start time of the first element can be omitted, meaning ôfrom nowö. The end time of the last element can be omitted, meaning ôuntil sampler is removedö. Values: List of (Start time, End time) ASSOCIATIONS Description: The ASSOCIATIONS field describes the observation point and the IPFIX processes to which the packet selector is associated. The STREAM ID denotes the origin of the data stream that is input to the selection function. It can be the observation point directly or the ID of another selector. With this it is possible to define combined schemes. If the STREAM ID contains IDs from other selectors, one can derive the original observation point from the selector definitions of these specified selectors. Values: STREAM ID, Metering process ID, Exporting process ID> With STREAM ID: Observation point ID | List of SELECTOR_IDs 9. Composite Techniques Zseby, Molina, Raspall Expires April 2003 [Page 12] Internet Draft Techniques for IP Packet Selection August 2002 Composite schemes are realized by using the STREAM ID in the information models. The STREAM ID denotes from which selectors the input stream originates. If multiple stream IDs are given, this means that the selector operates on the packet stream simply resulting from the time superposition of the output of all the listed filters and samplers. Note that a sampler/filter could be intermittently active, as defined in the OPERATING TIME field. Some examples of composite schemes are reported below. 9.1 Cascaded filtering->sampling or sampling->filtering If a filter precedes a sampling process the role of filtering is to create a set of ôparent populationsö from a single stream that can then be fed independently to different sampling functions, with different parameters tuned for the population itself (e.g. if streams of different intensity result from filtering, it may be good to have different sampling rates). If filtering follows a sampling process, the same sampling rate and type is applied to the whole stream, independently of the relative size of the streams resulting from the filtering function. Moreover, also packets not destined to be selected will ôloadö the sampling function. So, in principle, filtering before sampling allows a more accurate tuning of the sampling procedure, but if filters are too complex to work at full line rate (e.g. because they have to access router state information), sampling before filtering may be a need. 9.2 Stratified Sampling Stratified sampling is one example for using a composite technique. The basic idea behind stratified sampling is to increase the estimation accuracy by using a-priori information. The a-priori information is used to perform an intelligent grouping of the elements of the parent population. With this a higher estimation accuracy can be achieved with the same sample size. Stratified sampling divides the sampling process into multiple steps. First, the elements of the parent population are grouped into subsets in accordance to a given characteristic. This grouping can be done in multiple steps. Then samples are taken from each subset. The stronger the correlation between the characteristic used to divide the parent population and the characteristic of interest (for which an estimate is sought after), the easier is the consecutive sampling process and the higher is the stratification gain. For instance if the dividing characteristic were equal to the investigated characteristic, each element of the sub-group would be a perfect representative of that characteristic. In this case it would be sufficient to take one arbitrary element out of each subgroup to get the actual distribution of the characteristic in the parent population. Therefore stratified sampling can reduce the costs for the sampling process (i.e. the number of samples needed to achieve a given level of confidence). Zseby, Molina, Raspall Expires April 2003 [Page 13] Internet Draft Techniques for IP Packet Selection August 2002 For stratified sampling one has to specify classification rules for grouping the elements into subgroups and the sampling scheme that is used within the subgroups. The classification rules can be expressed by multiple filters. For the sampling scheme within the subgroups the parameters have to be specified as described above. 10. Security Considerations Security threats can occur if the configuration of sampling parameters or the communication of sampling parameters to the application is corrupted. This document only describes sampling schemes that can be used for packet selection. It neither describes a mechanism how those parameters are configured nor how these parameters are communicated to the application. Therefore the security threats that originate from this kind of communication cannot be assessed with the information given in this document. In some cases malicious users or attackers may be interested to hide packets from the service provider. For instance if packet selectors are used for accounting or intrusion detection applications, users may want to prevent that packets are selected. If a deterministic sampling scheme is used or a selection scheme that takes packet content into account, the user can shape or send packets in a way that they are less likely to be selected. This has to be taken into account when choosing an appropriate packet selection technique. 11. References [AmCa89] Paul D. Amer, Lillian N. Cassel: Management of Sampled Real-Time Network Measurements, 14th Conference on Local Computer Networks, October 1989, Minneapolis, pages 62- 68, IEEE, 1989 [ClPB93] K.C. Claffy, George C Polyzos, Hans-Werner Braun: Application of Sampling Methodologies to Network Traffic Characterization, Proceedings of ACM SIGCOMM'93, San Francisco, CA, USA, September 13 - 17, 1993 [CoGi98] I. Cozzani, S. Giordano: Traffic Sampling Methods for end-to-end QoS Evaluation in Large Heterogeneous Networks. Computer Networks and ISDN Systems, 30 (16- 18), September 1998. [DuGG02] Nick Duffield, Albert Greenberg, Matthias Grossglauser, Jennifer Rexford: A Framework for Passive Packet Measurement, Internet Draft draft-duffield-framework- papame-01, work in progress, February 2002 [DuGr00] Nick Duffield, Matthias Grossglauser: Trajectory Sampling for Direct Traffic Observation, Proceedings of ACM SIGCOMM 2000, Stockholm, Sweden, August 28 - September 1, 2000. Zseby, Molina, Raspall Expires April 2003 [Page 14] Internet Draft Techniques for IP Packet Selection August 2002 [JePP92] Jonathan Jedwab, Peter Phaal, Bob Pinna: Traffic Estimation for the Largest Sources on a Network, Using Packet Sampling with Limited Storage, HP technical report, Managemenr, Mathematics and Security Department, HP Laboratories, Bristol, March 1992, http://www.hpl.hp.com/techreports/92/HPL-92-35.html [QuZC02] J. Quittek, T. Zseby, B. Claise, S. Zander, G. Carle, K.C. Norseth: Requirements for IP Flow Information Export, Internet Draft , work in progress, August 2002 [Zseb02] Tanja Zseby: Deployment of Sampling Methods for SLA Validation with Non-Intrusive Measurements, Proceedings of Passive and Active Measurement Workshop (PAM 2002), Fort Collins, CO, USA, March 25-26, 2002 12. Author's Addresses Tanja Zseby Fraunhofer Institute for Open Communication Systems Kaiserin-Augusta-Allee 31 10589 Berlin Germany Phone: +49-30-34 63 7153 Fax: +49-30-34 53 8153 Email: zseby@fokus.fhg.de Maurizio Molina NEC Europe Ltd., Network Laboratories Adenauerplatz 6 69115 Heidelberg Germany Phone: +49 6221 90511-18 EMail: molina@ccrle.nec.de Fredric Raspall NEC Europe Ltd., Network Laboratories Adenauerplatz 6 69115 Heidelberg Germany Phone: +49 6221 90511-31 EMail: raspall@ccrle.nec.de 13. Full Copyright Statement Copyright (C) The Internet Society (2002). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this Zseby, Molina, Raspall Expires April 2003 [Page 15] Internet Draft Techniques for IP Packet Selection August 2002 document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Zseby, Molina, Raspall Expires April 2003 [Page 16]