PCP Working Group M. Boucadair Internet-Draft France Telecom Updates: 6887 (if approved) R. Penno Intended status: Standards Track D. Wing Expires: July 10, 2014 P. Patil T. Reddy Cisco January 06, 2014 PCP Server Selection draft-ietf-pcp-server-selection-02 Abstract Multiple IP addresses may be configured on a PCP client in some deployment contexts such as multi-homing. This document specifies the behavior to be followed by the PCP client to contact its PCP server(s) when one or several PCP server IP addresses are configured. This document updates RFC6887. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on July 10, 2014. Boucadair, et al. Expires July 10, 2014 [Page 1] Internet-Draft PCP Server Selection January 2014 Copyright Notice Copyright (c) 2014 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3 3. IP Address Selection . . . . . . . . . . . . . . . . . . . . 3 4. Multiple Interfaces . . . . . . . . . . . . . . . . . . . . . 4 5. Example: Multiple PCP servers on a Single Interface . . . . . 4 6. Security Considerations . . . . . . . . . . . . . . . . . . . 6 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 6 8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 6 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 6 9.1. Normative References . . . . . . . . . . . . . . . . . . 6 9.2. Informative References . . . . . . . . . . . . . . . . . 7 Appendix A. Multi-homing . . . . . . . . . . . . . . . . . . . . 8 A.1. IPv6 Multi-homing . . . . . . . . . . . . . . . . . . . . 8 A.2. IPv4 Multi-homing . . . . . . . . . . . . . . . . . . . . 9 1. Introduction Multiple IP addresses may be configured on a PCP client in some deployment contexts such as multi-homing (see Appendix A). A PCP server may also have multiple IP addresses associated with it. This document specifies the behavior to be followed by the PCP client [RFC6887] to contact its PCP server(s) [RFC6887] when it receives one or several PCP server IP addresses (e.g., using DHCP [I-D.ietf-pcp-dhcp]). This document is not specific to DHCP; any other mechanism can be used to configure PCP server IP addresses. It is out of scope of this document to enumerate all deployment scenarios that require multiple IP addresses to be configured. Boucadair, et al. Expires July 10, 2014 [Page 2] Internet-Draft PCP Server Selection January 2014 2. Terminology This document makes use of the following terms: o PCP server denotes a functional element that receives and processes PCP requests from a PCP client. A PCP server can be co- located with or be separated from the function (e.g., Network Address Translation (NAT), firewall) it controls. Refer to [RFC6887]. o PCP client denotes a PCP software instance responsible for issuing PCP requests to a PCP server. Refer to [RFC6887]. 3. IP Address Selection These steps specify the behavior to be followed by the PCP client to contact a PCP server when the PCP client has multiple IP addresses for a single PCP server. Additional considerations to be taken into account when the PCP client is multi-interfaced are specified in Section 4: 1. If the PCP client can use both address families when communicating to a particular PCP server, the PCP client SHOULD select the source address of the PCP request to be of the same IP address family as its requested PCP mapping (i.e., the address family of the Requested External IP Address). 2. Whenever communicating with a PCP server, the rules of Section 6 of [RFC6724] SHOULD be followed by using the source address selected in the previous step as input to the destination address selection algorithm. 3. The PCP client initializes its Maximum Retransmission Count (MRC) to 4. 4. The PCP client sends its PCP message to the PCP server's IP address following the retransmission procedure specified in Section 8.1.1 of [RFC6887]. If no response is received after MRC attempts, the PCP client re-tries the procedure excluding the destination addresses which did not respond. The PCP client SHOULD ignore any response received from an IP address after exhausting MRC attempts for that particular IP address. If, when sending PCP requests, the PCP client receives a hard ICMP error [RFC1122] it SHOULD immediately try the next IP address from the list of PCP server' IP addresses. Boucadair, et al. Expires July 10, 2014 [Page 3] Internet-Draft PCP Server Selection January 2014 5. If the PCP client has exhausted all IP addresses configured for a given PCP server, the procedure is repeated every fifteen minutes until the PCP request is successfully answered. 6. Once the PCP client has successfully received a response from a PCP server's IP address, it sends subsequent PCP requests to the same server's IP address until that IP address becomes non- responsive, which causes the PCP client to follow the steps above to contact its PCP server. For efficiency, the PCP client should use the same Mapping Nonce for requests sent to all PCP server' IP addresses. If several PCP servers are configured, each with multiple IP addresses, the PCP client contacts all PCP servers in parallel following the steps described above. This procedure may result in a PCP client instantiating multiple mappings maintained by distinct PCP servers. The decision to use all these mappings or delete some of them is implementation-specific and only the PCP client can decide whether all mappings are needed or only a subset of them. 4. Multiple Interfaces When an end host has multiple interfaces concurrently active (e.g., IEEE 802.11 and 3G), a PCP client would discover different PCP servers over different interfaces. A host may have multiple network interfaces (e.g, 3G, IEEE 802.11, etc.); each configured differently. Each PCP server learned MUST be associated with the interface via which it was learned. Particularly, the PCP client relies on the source IP address of an outgoing PCP request to select which PCP server(s) to use. Although multiple interfaces may be available, a PCP client might choose to use just one based on, for example, cost and bandwidth requirements, and therefore would need to send PCP requests to just one PCP server. Generic multi-interfaces considerations are documented in Section 8.4 of [RFC6887] 5. Example: Multiple PCP servers on a Single Interface Figure 1 depicts an example that is used to illustrate the server selection procedure specified in Section 3. Boucadair, et al. Expires July 10, 2014 [Page 4] Internet-Draft PCP Server Selection January 2014 ISP Network | | ......................................................... | | Subscriber Network +-------+------+ +----+---------+ | PCP-Server-A | | PCP-Server-B | | | | | +-------+------+ +----+---------+ 192.0.2.1 | | 198.51.100.1 2001:db8:2222::1 | | 2001:db8:3333::1 | | | | -------+--------------+----------- | | 203.0.113.0 | 2001:db8:1111::1 +---+---+ | Host | +-------+ Figure 1 The example shows the experienced behavior when a single IP address for one PCP server is not responsive. The PCP client is configured with two PCP servers, PCP-Server-A and PCP-Server-B each having two IP addresses, an IPv4 address and an IPv6 address. The PCP client wants an IPv4 mapping so it orders the addresses as follows: o PCP-Server-A: * 192.0.2.1 * 2001:db8:1111::1 o PCP-Server-B: * 198.51.100.1 * 2001:db8:2222::1 Suppose that: o The path to reach 192.0.2.1 is broken o The path to reach 2001:db8:1111::1 is working o The path to reach 198.51.100.1 is working Boucadair, et al. Expires July 10, 2014 [Page 5] Internet-Draft PCP Server Selection January 2014 o The path to reach 2001:db8:2222::1 is working The PCP client sends two PCP requests at the same time, the first to 192.0.2.1 (corresponding to PCP-Server-A) and the second to 198.51.100.1 (corresponding to PCP-Server-B). The path to 198.51.100.1 is working so a PCP response is received. Because the path to 192.0.2.1 is broken, no PCP response is received. The PCP client retries 4 times to elicit a response from 192.0.2.1 and finally gives up on that address and sends a PCP message to 2001::db8:1111:1. That path is working, and a response is received. Thereafter, the PCP client should continue using that responsive IP address for PCP-Server-A (2001:db8:1111::1). In this particular case, it will have to use THIRD_PARTY option for IPv4 mappings. 6. Security Considerations PCP-related security considerations are discussed in [RFC6887]. This document does not specify how PCP server addresses are provisioned to the PCP client. It is the responsibility of any PCP server provisioning document(s) to elaborate on the security considerations to discover a legitimate PCP server. 7. IANA Considerations This document does not request any action from IANA. 8. Acknowledgements Many thanks to Dave Thaler for the review and comments. 9. References 9.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC6724] Thaler, D., Draves, R., Matsumoto, A., and T. Chown, "Default Address Selection for Internet Protocol Version 6 (IPv6)", RFC 6724, September 2012. [RFC6887] Wing, D., Cheshire, S., Boucadair, M., Penno, R., and P. Selkirk, "Port Control Protocol (PCP)", RFC 6887, April 2013. Boucadair, et al. Expires July 10, 2014 [Page 6] Internet-Draft PCP Server Selection January 2014 9.2. Informative References [I-D.ietf-pcp-dhcp] Boucadair, M., Penno, R., and D. Wing, "DHCP Options for the Port Control Protocol (PCP)", draft-ietf-pcp-dhcp-09 (work in progress), November 2013. [RFC1122] Braden, R., "Requirements for Internet Hosts - Communication Layers", STD 3, RFC 1122, October 1989. [RFC1123] Braden, R., "Requirements for Internet Hosts - Application and Support", STD 3, RFC 1123, October 1989. [RFC3493] Gilligan, R., Thomson, S., Bound, J., McCann, J., and W. Stevens, "Basic Socket Interface Extensions for IPv6", RFC 3493, February 2003. [RFC4116] Abley, J., Lindqvist, K., Davies, E., Black, B., and V. Gill, "IPv4 Multihoming Practices and Limitations", RFC 4116, July 2005. Boucadair, et al. Expires July 10, 2014 [Page 7] Internet-Draft PCP Server Selection January 2014 Appendix A. Multi-homing The main problem of a PCP multi-homing situation can be succinctly described as 'one PCP client, multiple PCP servers'. As described in Section 3, if a PCP client discovers multiple PCP servers, it should send requests to all of them in parallel with the following assumptions: o There is no requirement that multiple PCP servers have the same capabilities. o PCP requests to different servers are independent, the result of a PCP request to one server does not influence another. o If PCP servers provide NAT, it is out of scope how the client manages ports across PCP servers. For example, whether PCP client requires all external ports to be the same or whether there are ports available at all. The following sub-sections describe multi-homing examples to illustrate the PCP client behavior. A.1. IPv6 Multi-homing In this example of an IPv6 multi-homed network, two or more routers co-located with firewalls are present on a single link shared with the host(s). Each router is in turn connected to a different service provider network and the host in this environment would be offered multiple prefixes and advertised multiple DNS servers. Consider a scenario in which firewalls within an IPv6 multi-homing environment also implement a PCP server. The PCP client learns the available PCP servers using DHCP [I-D.ietf-pcp-dhcp] or any other provisioning mechanism. In reference to Figure 2, a typical model is to embed DHCP servers in rtr1 and rtr2. A host located behind rtr1 and rtr2 can contact these two DHCP server and retrieves from each server the IP address of the corresponding PCP server. The PCP client will send PCP requests in parallel to each of the PCP servers. Boucadair, et al. Expires July 10, 2014 [Page 8] Internet-Draft PCP Server Selection January 2014 ================== | Internet | ================== | | | | +----+-+ +-+----+ | ISP1 | | ISP2 | +----+-+ +-+----+ ISP Network | | ......................................................... | | | | Subscriber Network +-------+---+ +----+------+ | rtr1 with | | rtr2 with | | FW1 | | FW2 | +-------+---+ +----+------+ | | | | -------+----------+------ | +---+---+ | Host | +-------+ Figure 2: IPv6 Multihoming A.2. IPv4 Multi-homing In this example an IPv4 multi-homed network described in 'NAT- or RFC2260-based multi-homing' (Section 3.3 of [RFC4116]), the gateway router is connected to different service provider networks. This method uses Provider-Aggregatable (PA) addresses assigned by each transit provider to which the site is connected. The site uses NAT to translate the various provider addresses into a single set of private-use addresses within the site. In such a case, two PCP servers have to be present to control NAT to each of the transit providers. The PCP client learns the available PCP servers using DHCP [I-D.ietf-pcp-dhcp] or any other provisioning mechanism. In reference to Figure 3, a typical model is to embed the DHCP server and the PCP servers in rtr1. A host located behind rtr1 can contact the DHCP server to obtain IP addresses of the PCP servers. The PCP client will send PCP requests in parallel to each of the PCP servers. Boucadair, et al. Expires July 10, 2014 [Page 9] Internet-Draft PCP Server Selection January 2014 ===================== | Internet | ===================== | | | | +----+--------+ +-+------------+ | ISP1 | | ISP2 | | | | | +----+--------+ +-+------------+ ISP Network | | | | .............................................................. | | | Port1 | Port2 Subscriber Network | | +----+-------------------+ |rtr1: NAT & PCP servers | | GW Router | +----+-------------------+ | | | -----+-------------- | +-+-----+ | Host | (private address space) +-------+ Figure 3: IPv4 Multihoming Authors' Addresses Mohamed Boucadair France Telecom Rennes 35000 France EMail: mohamed.boucadair@orange.com Reinaldo Penno Cisco USA EMail: repenno@cisco.com Boucadair, et al. Expires July 10, 2014 [Page 10] Internet-Draft PCP Server Selection January 2014 Dan Wing Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134 USA EMail: dwing@cisco.com Prashanth Patil Cisco Systems, Inc. Bangalore India EMail: praspati@cisco.com Tirumaleswar Reddy Cisco Systems, Inc. Cessna Business Park, Varthur Hobli Sarjapur Marathalli Outer Ring Road Bangalore, Karnataka 560103 India EMail: tireddy@cisco.com Boucadair, et al. Expires July 10, 2014 [Page 11]