PCP working group D. Wing Internet-Draft Cisco Intended status: Standards Track December 15, 2010 Expires: June 18, 2011 Port Control Protocol (PCP) draft-ietf-pcp-base-01 Abstract Port Control Protocol is an address-family independent mechanism to control how incoming packets are forwarded by upstream devices such as network address translators (NATs) and simple IPv6 firewalls. Status of this Memo This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on June 18, 2011. Copyright Notice Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect Wing Expires June 18, 2011 [Page 1] Internet-Draft Port Control Protocol (PCP) December 2010 to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 2. Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1. Deployment Scenarios . . . . . . . . . . . . . . . . . . . 4 2.2. Supported Transport Protocols . . . . . . . . . . . . . . 5 2.3. Single-homed Customer Premise Network . . . . . . . . . . 5 3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Relationship of PCP Server and its NAT . . . . . . . . . . . . 6 5. Common Request and Response Header Format . . . . . . . . . . 7 5.1. Request Header . . . . . . . . . . . . . . . . . . . . . . 8 5.2. Response Header . . . . . . . . . . . . . . . . . . . . . 9 5.3. Options . . . . . . . . . . . . . . . . . . . . . . . . . 9 5.4. Result Codes . . . . . . . . . . . . . . . . . . . . . . . 11 6. General Operation . . . . . . . . . . . . . . . . . . . . . . 12 6.1. General PCP Client Operation . . . . . . . . . . . . . . . 12 6.1.1. Generating and Sending a Request . . . . . . . . . . . 12 6.1.2. Processing a Response . . . . . . . . . . . . . . . . 13 6.1.3. Multi-interface Issues . . . . . . . . . . . . . . . . 13 6.2. General PCP Server Operation . . . . . . . . . . . . . . . 14 7. Pinhole Operation . . . . . . . . . . . . . . . . . . . . . . 14 7.1. OpCode Packet Format . . . . . . . . . . . . . . . . . . . 14 7.2. OpCode-Specific Error Codes . . . . . . . . . . . . . . . 17 7.3. OpCode-Specific Client Operation, Processing a Response . 17 7.4. OpCode-Specific Server Operation . . . . . . . . . . . . . 18 7.4.1. Maintaining Same External IP Address . . . . . . . . . 19 7.4.2. Pinhole Lifetime . . . . . . . . . . . . . . . . . . . 19 7.4.3. Pinhole deletion . . . . . . . . . . . . . . . . . . . 20 7.4.4. Subscriber Identification . . . . . . . . . . . . . . 20 7.4.5. Renumbering . . . . . . . . . . . . . . . . . . . . . 21 7.4.6. Disambiguating Remote Peer . . . . . . . . . . . . . . 21 7.5. PCP Options for PIN OpCodes . . . . . . . . . . . . . . . 22 7.5.1. REMOTE_PEER_FILTER . . . . . . . . . . . . . . . . . . 22 7.5.2. REMOTE_PEER . . . . . . . . . . . . . . . . . . . . . 23 7.5.3. HONOR_EXTERNAL_PORT . . . . . . . . . . . . . . . . . 24 7.6. Interaction with Dynamic Connections . . . . . . . . . . . 24 7.7. Using PCP to Eliminate Application Keepalive Messages . . 25 7.8. PCP Mapping State Maintenance . . . . . . . . . . . . . . 25 7.8.1. Epoch . . . . . . . . . . . . . . . . . . . . . . . . 26 7.8.2. Recreating Pinholes . . . . . . . . . . . . . . . . . 26 7.8.3. Maintaining Pinholes . . . . . . . . . . . . . . . . . 27 7.9. Nested NATs . . . . . . . . . . . . . . . . . . . . . . . 28 Wing Expires June 18, 2011 [Page 2] Internet-Draft Port Control Protocol (PCP) December 2010 7.10. Pinhole Deletion . . . . . . . . . . . . . . . . . . . . . 28 7.11. Pinhole Lifetime Extension . . . . . . . . . . . . . . . . 28 8. Deployment Scenarios . . . . . . . . . . . . . . . . . . . . . 29 8.1. Dual Stack-Lite . . . . . . . . . . . . . . . . . . . . . 29 8.1.1. Overview . . . . . . . . . . . . . . . . . . . . . . . 29 8.1.2. Encapsulation Mode . . . . . . . . . . . . . . . . . . 29 8.1.3. Plain IPv6 Mode . . . . . . . . . . . . . . . . . . . 30 8.2. NAT64 . . . . . . . . . . . . . . . . . . . . . . . . . . 30 8.3. NAT44 and NAT444 . . . . . . . . . . . . . . . . . . . . . 30 8.4. IPv6 Firewall . . . . . . . . . . . . . . . . . . . . . . 30 9. Interworking with UPnP IGD 1.0 and 2.0 . . . . . . . . . . . . 31 9.1. UPnP IGD 1.0 with AddPortMapping Action . . . . . . . . . 31 9.2. UPnP IGD 2.0 with AddAnyPortMapping Action . . . . . . . . 32 9.3. Lifetime Maintenance . . . . . . . . . . . . . . . . . . . 33 10. Security Considerations . . . . . . . . . . . . . . . . . . . 33 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 33 11.1. PCP Server IP address . . . . . . . . . . . . . . . . . . 33 11.2. Port Number . . . . . . . . . . . . . . . . . . . . . . . 34 11.3. OpCodes . . . . . . . . . . . . . . . . . . . . . . . . . 34 11.4. Result Codes . . . . . . . . . . . . . . . . . . . . . . . 34 11.5. Options . . . . . . . . . . . . . . . . . . . . . . . . . 34 12. Authors . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 35 14. References . . . . . . . . . . . . . . . . . . . . . . . . . . 35 14.1. Normative References . . . . . . . . . . . . . . . . . . . 35 14.2. Informative References . . . . . . . . . . . . . . . . . . 36 Appendix A. Changes . . . . . . . . . . . . . . . . . . . . . . . 37 A.1. Changes from -00 to -01 . . . . . . . . . . . . . . . . . 37 Appendix B. Analysis of Techniques to Discover PCP Server . . . . 38 Author's Address . . . . . . . . . . . . . . . . . . . . . . . . . 40 Wing Expires June 18, 2011 [Page 3] Internet-Draft Port Control Protocol (PCP) December 2010 1. Introduction Port Control Protocol (PCP) provides a mechanism to control how incoming packets are forwarded by upstream devices such as NATs and firewalls. PCP is primarily designed to be implemented in the context of both large scale NAT and small-scale NAT (e.g., residential NATs). PCP allows hosts to operate servers permanently (e.g., a webcam) or temporarily (e.g., while playing a game) when behind one or more NAT devices, including when behind a large-scale NAT operated by their Internet service provider. PCP allows applications to create pinholes from an external IP address to an internal IP address and port. If the PCP-controlled device is a NAT, a mapping is created; if the PCP-controlled device is a firewall, a pinhole is created in the firewall. These pinholes are required for successful inbound communications destined to machines located behind a NAT. After creating a pinhole for incoming connections, it is necessary to inform remote computers about the IP address and port for the incoming connection. This is usually done in an application-specific manner. For example, a computer game would use a rendezvous server specific to that game (or specific to that game developer), and a SIP phone would use a SIP proxy. PCP does not provide this rendezvous function. 2. Scope 2.1. Deployment Scenarios PCP can be used in various deployment scenarios, including: o DS-Lite [I-D.ietf-softwire-dual-stack-lite], including a NAT and including a router behind the B4 element, and; [Ed. Note: Do we want 'NAT behind the B4 element' in our scope? This affects PCP server discovery, among other things. Howeve, users deploy these NATs. Do we want PCP to work with this, detect this, or quietly fail??] o NAT64, both Stateful [I-D.ietf-behave-v6v4-xlate-stateful] and Stateless [I-D.ietf-behave-v6v4-xlate], and; o Large-Scale NAT44 [I-D.ietf-behave-lsn-requirements], including nested NATs ("NAT444"), and; Wing Expires June 18, 2011 [Page 4] Internet-Draft Port Control Protocol (PCP) December 2010 o Layer-2 aware NAT [I-D.miles-behave-l2nat] and Dual-Stack Extra Lite [I-D.arkko-dual-stack-extra-lite], and; o IPv6 firewall control [I-D.ietf-v6ops-cpe-simple-security]. 2.2. Supported Transport Protocols The PCP OpCodes defined in this document are designed to support transport protocols that use a 16-bit port number (e.g., TCP, UDP, SCTP, DCCP). Transport protocols that do not use a port number (e.g., IPsec ESP) can be wildcarded (allowing any traffic with that protocol to pass), provided of course the upstream device being controlled by PCP supports that functionality, or new PCP OpCodes can be defined to support those protocols. 2.3. Single-homed Customer Premise Network The PCP machinery assumes a single-homed subscriber model. That is, for a given IP version, only one default route exists to reach the Internet. This is important because after a PCP pinhole is created and an inbound packet (e.g., TCP SYN) arrives at the host the outbound response (e.g., TCP SYNACK) has to go through the same path so the proper address rewriting takes place on that outbound response packet. This restriction exists because otherwise there would need to be one PCP server for each egress, because the host could not reliably determine which egress path packets would take. 3. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Port Forwarding: Port forwarding allows a host to receive traffic sent to a specific IP address and port. In the context of a NAT or NAPT, the internal address and external address are different. In the context of a firewall, the internal address and external address are different. In both contexts, if an internal host is listening to connections on a specific port (that is, operating as a server), the external IP address and port number need to be port forwarded to the internal IP address and port number. In the context of a NAPT, it is possible that both the IP address and port are modfiied. For example with a NAPT, a webcam might be listening Wing Expires June 18, 2011 [Page 5] Internet-Draft Port Control Protocol (PCP) December 2010 on port 80 on its internal address 192.168.1.1, while its publicly-accessible external address is 192.0.2.1 and port is 12345. The NAT does 'port forwarding' of one to the other. In the context of a firewall, the internal address, external IP address, and ports are not changed. PCP Client: A PCP software instance responsible for issuing PCP requests to a PCP Server. One or several PCP Clients can be embedded in the same host. Several PCP Clients can be located in the same local network of a given subscriber. A PCP Client can issue PCP request on behalf of a third party device of the same subscriber. An interworking function, from UPnP IGD to PCP, or from PCP to PCP (for nested NATs) is another example of a PCP client. PCP Server: A network element which receives and processes PCP requests from a PCP Client. See also Section 4. Mapping: See also Port Forwarding. A mapping exists only in the context of a Network Address Translator. A NAT mapping creates a relationship between an internal IP transport address and an external IP transport address. More specifically, it creates a translation rule where packets destined to the external IP and port are translated to the internal IP and port. Mapping Types: There are three different ways to create mappings: dynamic (e.g., outgoing TCP SYN), PCP, and static configured (e.g., CLI or web page). These mappings are one and the same but their attributes such as lifetime or filtering might be different. Interworking Function: a functional element responsible for interworking another protocol with PCP. For example interworking between UPnP IGD [IGD] with PCP. 4. Relationship of PCP Server and its NAT The PCP server receives PCP requests. The PCP server might be integrated within the NAT or firewall device (as shown in Figure 1) Wing Expires June 18, 2011 [Page 6] Internet-Draft Port Control Protocol (PCP) December 2010 which is expected to be a common deployment. +-----------------+ +------------+ | NAT or firewall | | PCP Client |--+ +--- +------------+ | with embedded | | PCP server | +-----------------+ Figure 1: device with Embedded PCP Server However, it is useful to also model a separation of the PCP server from the NAT, as shown below (Figure 2). The PCP server would communicate with the NAT using a protocol beyond the scope of this document, such as a proprietary protocol or any suitable standard protocol for NAT control. +-----------------+ +--+ NAT or firewall +--- / +-----------------+ +------------+ / ^ | PCP Client +- | any suitable control protocol +------------+ \ v \ +------------+ +--+ PCP Server | +------------+ Figure 2: NAT with Separate PCP Server 5. Common Request and Response Header Format All PCP messages contain a request (or response) header, opcode- specific information, and (optional) informational elements. The packet layout for the common header, and operation of the PCP client and PCP server are described in the following sections. The information in this section applies to all OpCodes. Behavior of specific OpCodes defined in this document is described in Section 7, and behavior of new OpCodes are described in their own documents following a similar format as in Section 7. Wing Expires June 18, 2011 [Page 7] Internet-Draft Port Control Protocol (PCP) December 2010 5.1. Request Header All requests have the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Ver=0 |reserve|R| OpCode | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved (32 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : (optional) opcode-specific information : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : (optional) PCP Options : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 3: Common Request Packet Format These fields are described below: Ver: Version is 0 reserve: 4 reserved bits, MUST be sent as 0 and MUST be ignored when received. R: Indicates Request (0) or Response (1). All Requests MUST use 0. OpCode: Opcodes are defined in Figure 7. More can be defined per rules described in Section 11. Reserved: 16 reserved bits, MUST be sent as 0 and MUST be ignored when received. Wing Expires June 18, 2011 [Page 8] Internet-Draft Port Control Protocol (PCP) December 2010 5.2. Response Header All responses have the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Ver=1 |reserve|R| Opcode | Reserved | Result Code | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Epoch | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : (optional) OpCode-specific response data : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : (optional) Informational Elements : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 4: Common Response Packet Format These fields are described below: Ver: Version is 1 reserve: 4 reserved bits, MUST be sent as 0, MUST be ignored when received. R: Indicates Request (0) or Response (1). All Responses MUST use 1. OpCode+128: The OpCode value from the request. Protocol: Protocol field, echoed exactly from the request Result Code: The result code for this response. See Section 5.4 for values. Epoch: The server's Epoch value. The same value is used for all PCP clients. See Section 7.8.1 for discussion. 5.3. Options A PCP OpCode can be extended with an Option. Options can be used in requests and responses. It is anticipated that Options will include information which are associated with the normal function of an OpCode.For example, an Option could indicate DSCP markings to apply to incoming or outgoing traffic associated with a PCP pinhole, or an Open could include descriptive text (e.g., "for my webcam"). Wing Expires June 18, 2011 [Page 9] Internet-Draft Port Control Protocol (PCP) December 2010 Options use the following Type-Length-Value format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Option Code | Reserved | Option-Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : data : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 5: Options Header The description of the fields is as follows: Option Code: Option code, 8 bits. The first bit of the option code is the "P" bit, described below. Option codes MUST be registered with IANA following the procedure described in Section 11. Reserved: MUST be set to 0 on transmission and MUST be ignored on reception. Option-Length: Indicates in units of 4 octets the length of the enclosed data. Options with length of 0 are allowed. data: Option data. The option data MUST end on a 32 bit boundary, padded with 0's when necessary. A given Option MAY be included in a request. An Option MUST NOT appear in a PCP response unless solicited in the associated request. If a given Option was included in a request, and understood and processed by the PCP server, it MUST be included in the response. The handling of an Option by the PCP Client and Server MUST be specified in a appropriate document and must include whether the PCP Option can appear (one or more times) in a request, and indicate the contents of the Option in the response. If the "P" bit in the OpCode is set, o the PCP server MUST only generate a positive PCP response if it can successfully process the PCP request and this Option. o if the PCP server does not implement this Option, it MUST generate a failure response without including this Option in the response. o If the PCP server does implement this Option, but cannot perform the function indicated by this Option, it MUST generate a failure response and include this Option (and its arguments) in the response. Wing Expires June 18, 2011 [Page 10] Internet-Draft Port Control Protocol (PCP) December 2010 If the "P" bit is clear, the PCP server MAY process or ignore this Option. If several Options are to be included in a PCP request or response, the Options MAY be encoded in any order by the PCP Client. The response MUST encode them in the same order, but may omit some PCP Options in the response (e.g., to indicate the PCP server does not understand that Option, or that Option is not included in responses). A single Option MAY appear more than once, if permitted by the defintion of the Option itself. If the Option's definition allows the Option to appear only once, the PCP server MUST respond to such a PCP request with an error message [[which error?]] To enhance interoperability, newly defined Options should avoid interdependencies with each other. New Options MUST include the information below: This Option: number: is valid for OpCodes: is included in responses: [MUST | MUST NOT] has length: appear more than once: ["yes" | "no"] 5.4. Result Codes The following response codes may be returned as a result of any OpCode received by the PCP server. Result codes are 8 bits long and the most significant bit indicates if the error is transient or permanent. A transient error is one that might resolve itself, such that an identical PCP request submitted later would be successful (e.g., a resource is consumed and might become available later). A permanent error is one that cannot reasonably be successful if an identical PCP request is submitted (e.g., unsupported opcode). Future result codes should follow this same format. 0 - Success 128 - Unsupported version 129 - Unsupported OpCode Figure 6: PCP Result Codes Wing Expires June 18, 2011 [Page 11] Internet-Draft Port Control Protocol (PCP) December 2010 Other result codes, specific to the OpCodes defined in this document, are listed in Section 7.2. 6. General Operation PCP messages MUST be sent over UDP, and the PCP Server MUST listen for PCP requests on the PCP port number (Section 11.2). Every PCP request generates a response, so PCP does not need to run over a reliable transport protocol. 6.1. General PCP Client Operation This section details operation specific to a PCP client, for any OpCode. Procedures specific to the PIN OpCodes are described in Section 7. 6.1.1. Generating and Sending a Request Prior to sending its first PCP message, the PCP client determines which servers to use. The PCP client tries the following to get a list of PCP servers: 1. if a PCP server is is configured (e.g., in a configuration file), the address(es) of the PCP server(s) are used as the list of PCP server(s), else; 2. if DHCP indicates the PCP server(s), the address(es) of the indicated PCP server(s) are used as the list of PCP server(s), else; 3. if the PCP working group decides an IANA-allocated address for the PCP server is suitable, it is added to the list of PCP servers, else; 4. the address of the default router, it is added to the list of PCP servers. [Ed. Note: more discussion around these methods is necessary to reach consensus on the best approach(es) for PCP. Also see Appendix B for further analysis.] With that list of PCP servers, the PCP client formulates its PCP request. The PCP request contains a PCP common header, PCP OpCode and payload, and optional Information Elements. It initializes a retransmission timer to 4 seconds. The PCP client sends a PCP message to each server in sequence, waiting for a response until its timer expires. Once a PCP client has successfully communicated with Wing Expires June 18, 2011 [Page 12] Internet-Draft Port Control Protocol (PCP) December 2010 a PCP server, it continues communicating with that PCP server until that PCP server becomes non-responsive, which causes the PCP client to attempt to re-iterate the procedure starting with the first PCP server on its list. If a hard ICMP error is received (e.g., port unreachable, network unreachable) the PCP client SHOULD immediately abort trying to contact that PCP server. If no response is received from any of those servers, it doubles its retransmission timer and tries each server again. This is repeated 4 times. If, after repeating the procedure 4 times, no PCP server has responded the PCP client SHOULD abort the procedure. 6.1.2. Processing a Response The PCP client receives the response and verifies the source IP address and port belong to the PCP server of an outstanding request. It validates the version number and OpCode matches an outstanding request. The response is further matched by comparing fields in the response OpCode-specific data to fields in the request OpCode- specific data. This matching is described by the OpCode itself, see Section 7.3. After a successful match with an outstanding request, the PCP client checks the Epoch field to determine if it needs to restore its state to the PCP server (see Section 7.8.1). If it is an error response (>0), the request failed. If the error response is less than 128, retrying the same request sometime in the future might be successful. If the error response is greater or equal to 128, retrying the same request is unlikely to be successful. If it is the success response (0), the PCP client knows the request was successful. 6.1.3. Multi-interface Issues Hosts which desire a PCP mapping might be multi-interfaced (i.e., own several logical/physical interfaces). Indeed, a host can be dual- stack or be configured with several IP addresses. These IP addresses may have distinct reachability scopes (e.g., if IPv6 they might have global reachability scope as for GUA (Global Unicast Address) or limited scope such as ULA (Unique Local Address, [RFC4193])). IPv6 addresses with global reachability scope SHOULD be used as internal IP address when instructing a PCP mapping in a PCP- controlled device. IPv6 addresses with limited scope (e.g., ULA), SHOULD NOT be indicated as internal IP address in a PCP message. As mentioned in Section 2.3, only mono-homed CP routers are in scope. Therefore, there is no viable scenario where a host located behind a CP router is assigned with two GUA addresses belonging to the same Wing Expires June 18, 2011 [Page 13] Internet-Draft Port Control Protocol (PCP) December 2010 global IPv6 prefix. [Ed. Note: text regarding multi-homing needs work.] 6.2. General PCP Server Operation This section details operation specific to a PCP server. Upon receiving a PCP request message, the PCP Server parses and validates it. A valid request contains a valid PCP common header, one valid PCP Opcode, and optional Options (which the server might or might not comprehend). If an error is encountered during processing, the server generates an error response which is sent back to the PCP client. After successful parsing of the message, the PCP server validates that the internal IP address in the PCP request belongs to that subscriber. This validation depends on the PCP deployment scenario; see Section 7.4.4. If the internal IP address in the PCP request does not belong to the subscriber, an error response MUST be generated with result code NOT_AUTHORIZED. 7. Pinhole Operation This document defines four OpCodes for forwarding ports and controlling dynamic connections. These four OpCodes share a similar packet layout for requests and responses. They are: PIN44 = 0 = IPv4 address to IPv4 address (e.g., NAT44 or firewall) PIN46 = 1 = IPv4 address to IPv6 address (e.g., NAT46 or firewall) PIN64 = 2 = IPv6 address to IPv4 address (e.g., NAT64 or firewall) PIN66 = 3 = IPv6 address to IPv6 address (e.g., NAT66 or firewall) Figure 7: OpCodes These operation of these OpCodes is described in this section. 7.1. OpCode Packet Format The four PIN OpCodes (PIN44, PIN46, PIN64, PIN66) share a similar packet layout for both requests and responses. Because of this similarity, they are shown together. For all of the PIN OpCodes, if the request's internal-ip-address and internal-port matches the response's external-ip-address and external-port, the IP addresses and ports are not changed and thus the functionality is purely a firewall; otherwise it pertains to a network address translator which Wing Expires June 18, 2011 [Page 14] Internet-Draft Port Control Protocol (PCP) December 2010 might also perform firewall functions. The following diagram shows the request packet format for PIN44, PIN46, PIN64, and PIN66. This packet format is aligned with the response packet format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Protocol | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Pinhole Internal IP address (32 or 128, depending on OpCode) : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Requested external IP address (32 or 128, depending on OpCode): : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Requested lifetime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | internal port | requested external port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 8: PIN OpCode Request Packet Format These fields are described below: Protocol: indicates protocol associated with this opcode. Values are taken from the IANA protocol registry [proto_numbers]. For example, this field contains 6 (TCP) if the opcode is intended to create a TCP mapping. If a particular OpCode does not need the field, it MUST sent as 0 and MUST be ignored when received. Reserved: MUST be 0 on transmission and MUST be ignored on reception. Pinhole Internal IP Address: Internal IP address of the pinhole. This can be IPv4 or IPv6, depending on the OpCode. Requested External IP Address: Requested external IP address. This is useful for refreshing a mapping, especially after the PCP server loses state. If the PCP server can fulfill the request, it will do so. If the PCP client doesn't know the external address, or doesn't have a preference, it MUST use 0. Wing Expires June 18, 2011 [Page 15] Internet-Draft Port Control Protocol (PCP) December 2010 Requested lifetime: Requested lifetime of this pinhole, in seconds. internal port: Internal port for the pinhole. Requested external port: requested external port for the mapping. This is useful for refreshing a mapping, especially after the PCP server loses state. If the PCP server can fulfill the request, it will do so. If the PCP client doesn't know the external port, or doesn't have a preference, it MUST use 0. The following diagram shows the response packet format for PIN44, PIN46, PIN64, and PIN66: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Protocol | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Pinhole Internal IP address (32 or 128, depending on OpCode) : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Assigned external IP address (32 or 128, depending on OpCode) : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Assigned lifetime | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | internal port | assigned external port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 9: PIN OpCode Response Packet Format These fields are described below: Protocol: Copied from the request. Reserved: MUST be 0 on transmission, MUST be ignored on reception. Pinhole Internal IP address: Copied from the request. IPv4 or IPv6 address is indicated by the OpCode. Assigned external IP address: Assigned external IPv4 or IPv6 address for the pinhole. IPv4 or IPv6 address is indicated by the OpCode Wing Expires June 18, 2011 [Page 16] Internet-Draft Port Control Protocol (PCP) December 2010 Assigned Lifetime: Lifetime for this mapping, in seconds Internal port: Internal port for the pinhole, copied from request. Assigned external port: requested external port for the mapping. IPv4 or IPv6 address is indicated by the OpCode 7.2. OpCode-Specific Error Codes In addition to the response codes described in Figure 6, the following additional response codes may be returned as a result of the four PIN OpCodes received by the PCP server. 130 - NOT_AUTHORIZED (e.g., PCP server supports mapping, but feature is disabled) 3 - Network Failure (e.g., NAT device has not obtained a DHCP lease) 4 - Out of resources (e.g., NAT device cannot create more mappings at this time) [Ed. Note: probably need an OpCode indicating that the REMOTE_PEER option is necessary to disambiguate a connection. Do we require the PCP server to figure out there is an ambiguity (multiple connections using the same port)? Probably.] Figure 10: Result Codes specific to PIN OpCodes Other OpCodes are in result codes are defined following the procedure in Section 11.4. 7.3. OpCode-Specific Client Operation, Processing a Response [Ed. Note: describe how PCP client sends a PIN* request, and might get an Invalid Opcode response, and what it does.] This section describes the operation of a client when sending the OpCodes PIN44, PIN64, PIN46, or PIN66. A response is matched with a request by comparing the protocol, internal IP address, internal port, remote peer address and remote peer port. Other fields are not compared, because the PCP server changes those fields to provide information about the pinhole created by the OpCode. If a successful response, the PCP client can use the external IP address and port(s) as desired. Typically the PCP client will communicate the external IP address and port(s) to another host on Wing Expires June 18, 2011 [Page 17] Internet-Draft Port Control Protocol (PCP) December 2010 the Internet using an application-specific rendezvous mechanism. If an unsucessful response code greater than or equal to 128, the PCP client SHOULD NOT re-issue the same request. If a response code less than or equal to 127, the PCP client MAY, if it wishes, resend the same message after a delay of at least 5 seconds. 7.4. OpCode-Specific Server Operation This section describes the operation of a client when processing the OpCodes PIN44, PIN64, PIN46, or PIN66. If the requested lifetime is 0, it indicates a Delete request. This means the pinhole described by the internal IP address should be deleted, and requested external port field is ignored by the server (that is, it isn't validated). If the deletion request was successful, a positive response generated containing external port of 0 and lifetime of 0. If the deletion request was unsusccessful a non-zero result code is returned and the lifetime is undefined. If the client attempts to delete a port mapping which was manually assigned by some kind of configuration tool, the PCP server MUST respond with a 'Not Authorized' error (result code 2). [Ed. Note: Should we similarly return an error if attempting to delete mappings that were created dynamically (e.g., TCP SYN)?] [Ed. Note: Issue #15: Should ICMP messages, associated with this pinhole, be allowed by default. Consensus appears to be 'yes', because that is what dynamic mappings on NATs do. And if we don't do this, we will have PCP clients forget (or avoid) requesting an ICMP pinhole, further degrading ICMP operation on the Internet.] [Ed. Note: The following text needs discussion. Keep it or discard it?] When a mapping is destroyed as a result of its lifetime expiring or for any other reason, if the NAT gateway's internal state indicates that there are still active TCP connections traversing that now- defunct mapping, then the NAT gateway SHOULD send appropriately- constructed TCP RST (reset) packets both to the local client and to the remote peer on the Internet to terminate that TCP connection. A client can request the explicit deletion of all its UDP or TCP mappings by sending the same deletion request to the NAT gateway with external port, internal port, and lifetime set to 0. A client MAY choose to do this when it first acquires a new IP address in order to protect itself from port mappings that were performed by a previous owner of the IP address. After receiving such a deletion request, the PCP server and NAT MUST delete all the port mappings. The PCP Wing Expires June 18, 2011 [Page 18] Internet-Draft Port Control Protocol (PCP) December 2010 server responds to such a deletion request with a response as described above, with the internal port set to zero. If the PCP server is unable to delete a port mapping, for example, because the mapping was manually configured by a configuration tooll, the gateway MUST still delete as many port mappings as possible, but respond with a non-zero result code. The exact result code to return depends on the cause of the failure. If the gateway is able to successfully delete all port mappings as requested, it MUST respond with a result code of 0. The PCP-controlled device MAY reduce the lifetime that was requested by the PCP Client. The PCP-controlled device SHOULD NOT offer a lease lifetime greater than that requested by the PCP Client. The RECOMMENDED lifetime assigned by the server is 7200 seconds (i.e., two hours). By default, a PCP-controlled device MUST NOT create mappings for a protocol not indicated in the request. For example, if the request was for a TCP mapping, a UDP mapping MUST NOT be created. Nevertheless, a configurable feature MAY be supported by the PCP- controlled device, which MAY reserve (but not forward) the companion port so the same PCP Client can request it in the future. If all of the proceeding operations were successful (did not generate an error response), then the requested pinholes are created as described in the request and a positive response is built. This positive response contains the same OpCode as the request plus 128. 7.4.1. Maintaining Same External IP Address If there are active mappings for a particular PCP Client -- created via dynamic assignment or created by PCP -- subsequent mapping requests from that same PCP Client MUST use the same external IP address. This is necessary because some protocols require using the same IP address for several ports, and follows REQ-1 of [I-D.ietf-behave-lsn-requirements]. Once a client has no active dynamic mappings and no PCP pinholes, a subsequent dynamic mapping or PCP request MAY be assigned to a different external IP address. 7.4.2. Pinhole Lifetime Once a PCP server has responded positively to a pinhole request for a certain lifetime, the port forwarding is active for the duration of the lifetime unless deleted by the PCP client (or until the PCP server crashes). This has interactions with dynamically-created mappings, see Sections Section 7.6. It is NOT RECOMMENDED that the server allow long lifetimes (exceeding Wing Expires June 18, 2011 [Page 19] Internet-Draft Port Control Protocol (PCP) December 2010 24 hours), because they will consume ports even if the internal host is no longer interested in receiving the traffic or no longer connected to the network. The PCP server SHOULD be configurable for permitted minimum and maximum lifetime, and the RECOMMENDED values are 120 seconds for the minimum value and 24 hours for the maximum. 7.4.3. Pinhole deletion A pinhole MUST be deleted by the PCP Server upon the expiry of its lifetime, or upon request from the PCP client. In order to prevent another subscriber from receiving unwanted traffic, the PCP server SHOULD NOT assign that same external port to another host for 120 seconds (MSL, [RFC0793]). [Ed. Note: it should (MUST?) allow the same host to re-acquire the same port, though.] 7.4.4. Subscriber Identification The PIN OpCodes require subscriber identification because they allocate resources to a subscriber. A PCP Client can create mappings in a PCP-controlled device on behalf of a third party device (e.g., a computer can create PCP mappings on behalf of a webcam). However, a PCP client cannot open pinholes for a different subscriber. The mechanism to identify "same subscriber" depends on the sort of NAT on this network: o If the PCP-controlled device is a NAT64: the internal IP address indicated in the PCP message and the source IPv6 address of received PCP request MUST belong to the same IPv6 prefix. The length of the IPv6 prefix is the same as the length assigned to each subscriber on that particular network (e.g., /64), and that length must be configurable by the network operator. o If the PCP-controlled device is a DS-Lite AFTR: DS-Lite (Section 11 of [I-D.ietf-softwire-dual-stack-lite]) already requires the tunnel transport source address be validated, and that same address is used by PCP to assign the tunnel-ID to the requested mapping (see Section 8.1.2 and Section 8.1.3). Thus, PCP acquires the same security properties as DS-Lite. If address validation is implemented correctly, the PCP Client can not instruct mappings on behalf of devices of another subscriber. o If LSN with a routed network (NAT44), each subscriber has a known set of IPv4 address (usually one IPv4 address) and all PCP Wing Expires June 18, 2011 [Page 20] Internet-Draft Port Control Protocol (PCP) December 2010 requests MUST be sent from only one of the subscriber's IP addresses and MUST only open pinholes towards the subscriber's own own IP address. o If IPv6 firewall: the internal IP address indicated in the PCP message and the source IPv6 address of received PCP request MUST belong to the same IPv6 prefix. The length of the IPv6 prefix is the same as the length assigned to each subscriber on that particular network (e.g., /64), and that length must be configurable by the network operator. PCP-controlled devices can be a DS-Lite AFTR or an IPv4-IPv6 interconnection node such as NAT46 or NAT64. These nodes are deployed by Service Providers to deliver global connectivity service to their customers. Appropriate functions to restrict the use of these resources (e.g., LSN facility) to only subscribed users should be supported by these devices. Access control can be implicit or explicit: o It is said to be explicit if an authorisation procedure is required for a user to be granted access to such resources. For such variant of PCP-controlled device, a subscriber can be identified by an IPv6 address, an IPv4 address, a MAC address, or any other information. o For other scenarios, such as plain IPv4-in-IPv6 encapsulation for a DS-Lite architecture, the access to the service is based on the source IPv6 prefix. No per-user polices is pre-configured in the PCP-controlled device. 7.4.5. Renumbering The customer premise router might obtain a new IPv6 prefix, either due to a reboot, power outage, DHCPv6 lease expiry, or other action. If this occurs, the ports reserved using PCP might be delivered to another customer who now has that (old) address. This same problem can occur if an IP address is re-assigned today, without PCP. The solution is the same as today: ISPs should not re-assign IP addresses. 7.4.6. Disambiguating Remote Peer When operating a UDP or TCP server, one application is listening on a port and no other application will be assigned that port by the operating system. However, ephemeral connections (that is, outgoing connections) to different servers can share the same ephemeral port, even between applications. If a PCP request with a PIN OpCode is sent after such a dynamic connection is established (potentially by Wing Expires June 18, 2011 [Page 21] Internet-Draft Port Control Protocol (PCP) December 2010 another application), the PCP server cannot reliable distinguish if the PIN request is referring to the current connection or to a new connection. To eliminate this ambiguity, the remote peer's IP address and port can be specified in the REMOTE_PEER Option. This Option does not create or modify filtering on the NAT (for that, use REMOTE_PEER_FILTER) and have no effect on the NAT or firewall's normal filtering which will be any combination of Endpoint- Independent Filtering, Address-Dependent Filtering, or Address and Port-Dependent Filtering (these terms are originally defined and explained in [RFC4787]). 7.5. PCP Options for PIN OpCodes 7.5.1. REMOTE_PEER_FILTER This Option indicates packet filtering is desired. The remote peer port and remote peer IP Address indicate the permitted remote peer's source IP address and port for packets from the Internet. That is, packets with a source IP address, transport, or port that do not match those fields of the PCP request are dropped by the PCP server- controlled NAT/firewall device. As a consequence of dropping the packet, an ICMP port unreachable error SHOULD be generated, as long as it does not violate the security policy of the NAT/firewall. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Remote Peer Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Remote Peer IP address (32 bits if PIN44 or PIN64, : : 1 28 bits if PIN46 or PIN66) : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ This Option: value: 128 is valid for OpCodes: PIN44, PIN64, PIN46, or PIN66 is included in responses: MUST has length: 64 or 160 may appear more than once: no Because of interactions with dynamic ports (Section 7.6), this Option Wing Expires June 18, 2011 [Page 22] Internet-Draft Port Control Protocol (PCP) December 2010 MUST only be used by a client that is operating a server, as this ensures that no other application will be assigned the same ephemeral port for its outgoing connection. Other use by a PCP client is NOT RECOMMENDED and will cause some UNSAF NAT traversal mechanisms [RFC3424] to fail where they would have otherwise succeeded, breaking other applications running on this same host. [Ed. Note: How do we want to remove a filter? Do we want to allow removing a filter at all -- is there a use-case for that or can the application just create a new mapping? If we have a use- case, perhaps use 0.0.0.0 as the remote IP address to remove all filters? 7.5.2. REMOTE_PEER Due to a pre-existing dynamic mapping, a PCP server may not be able to instantiate a filter on a specific port. It is thus recommended that applications bind to the source port (to prevent other applications from using that same source port) prior to using this PCP Option. In those situations, the Option REMOTE_PEER is necessary to disambiguate the mappings. This option does not change filtering behavior of the NAT or firewall. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reserved | Remote Peer Port | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ : : : Remote Peer IP address (32 bits if PIN44 or PIN64, : : 1 28 bits if PIN46 or PIN66) : : : +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ This Option: value: 129 is valid for OpCodes: PIN44, PIN64, PIN46, or PIN66 is included in responses: MUST has length: 64 or 160 may appear more than once: no Wing Expires June 18, 2011 [Page 23] Internet-Draft Port Control Protocol (PCP) December 2010 7.5.3. HONOR_EXTERNAL_PORT This option indicates the PCP client needs to have the indicated requested-eternal-port allocated. If the PCP server cannot provide that port for the exclusive use of the PCP client, the PCP server MUST return an error [which code should we use?]. This option is intended for use by UPnP IGD interworking (Section 9). This Option: value: 6 is valid for OpCodes: PIN44, PIN64, PIN46, or PIN66 is included in responses: MUST has length: 0 may appear more than once: no 7.6. Interaction with Dynamic Connections Dynamic connections are created by hosts sending a TCP or UDP packet across their NAT. PCP can be used with such dynamic connections. There are two interesting cases: PCP before a dynamic connection, and PCP after a dynamic connection. If two applications on the same host communicate with different destinations, it is possible for them to be allocated the same ephemeral source port -- without either of the applications using the REUSEADDR socket option. Thus, one application's use of PCP (to adjust the NAT or firewalls behavior) can affect an unrelated application on the same host. This is why the four PIN OpCodes include the remote peer fields. The remote peer fields allow the PCP server to to disambiguate which mapping applies to the PIN OpCode message. Because PCP is not intended to adjust NAT behavior for dynamically- created connections, it is possible (and reasonable) for that second dynamic connection to be mapped to a different public port. Even if that occurs, the other application can issue its own PCP request (to determine the mapping lifetime) following the same procedure described in this section. Wing Expires June 18, 2011 [Page 24] Internet-Draft Port Control Protocol (PCP) December 2010 7.7. Using PCP to Eliminate Application Keepalive Messages Middleboxes such as NATs or firewalls need to see occasional traffic or will terminate their session state, causing application failures. To avoid this, many applications routinely generate keepalive traffic for the primary or sole purpose of maintaining state with such middleboxes. Applications can avoid such application keepalive traffic by using PCP. To use PCP for this function, the applications first connects to its server, as normal. Afterwards, it issues a PCP PIN request (PIN44, PIN64, PIN46, or PIN66, as appropriate) specifying the same 5-tuple as that connection in the PCP PIN request (internal IP address and port, transport protocol, and remote peer IP address and port), with requested-external-address and requested-external-port both set to 0, and includes the REMOTE_PEER Option indicating the remote peer's IP address is from the perspective of the PCP client. The PCP response will indicate the lifetime for that session. On many common platforms (i.e. those making use of the BSD sockets API), using PCP for purposes of application keepalives by issuing a PCP request followed by a dynamic connection to the server is difficult to implement properly. This is therefore NOT RECOMMENDED. Instead, client applications SHOULD first establish a dynamic connection to a server, and then issue a PCP request related to that connection, including the REMOTE_PEER option. The following pseudo-code shows how PCP can be reliably used with a dynamic socket, for the purposes of reducing application keepalive messages: int s = socket(...); connect(s, &remote_peer, ...); getsockname(s, &internal_address, ...); pcp_send_request(internal_address, 0, remote_peer, lifetime); /* external address is set to zero */ Figure 11: Pseudo-code for using PCP to with a dynamic socket 7.8. PCP Mapping State Maintenance If an event occurs that causes the PCP server to lose state (such as a crash or power outage), the pinholes created by PCP are lost. Such loss of state is rare in a service provider environment (due to redundant power, disk drives for storage, etc.). But such loss of state is more common in a residential NAT device which does not write information to its non-volatile memory. Wing Expires June 18, 2011 [Page 25] Internet-Draft Port Control Protocol (PCP) December 2010 The Epoch indicates if the PCP server has lost its state. If this occurs, the PCP client can attempt to recreate the pinholes following the procedures described in this section. 7.8.1. Epoch Every PCP response sent by the PCP Server includes an Epoch field. This field increments by 1 every second, and indicates to the PCP client if PCP state needs to be restored. If the PCP Server resets or loses the state of its port mapping table, due to reboot, power failure, or any other reason, it MUST reset its Epoch time to 0. Similarly, if the public IP address of the NAT (controlled by the PCP server) changes, the Epoch MUST be reset to 0. Whenever a client receives a PCP response, the client computes its own conservative estimate of the expected Epoch value by taking the Epoc value in the last packet it received from the gateway and adding 7/8 (87.5%) of the time elapsed since that packet was received. If the Epoch value in the newly received packet is less than the client's conservative estimate by more than one second, then the client concludes that the PCP server lost state, and the client MUST immediately renew all its active port mapping leases as described in Section 7.8.2. [Ed. Note: comment from Dave Thaler: "So spoofed packets with Epoch=0 that look like they come from the server could result in a big amplification attack on the PCP server. How is this mitigated?"] 7.8.2. Recreating Pinholes The PCP server SHOULD store mappings in persistent storage so when it is powered off or rebooted, it remembers the port mapping state of the network. Due to the physical architecture of some PCP servers, this is not always achievable (e.g., some non-volatile memory can withstand only a certain number of writes, so writing PCP mappings to such memory is generally avoided). However, maintaining this state is not essential for correct operation. When the PCP server loses state and begins processing new PCP messages, its Epoch is reset to zero (per the procedure of Section 7.8.1). A mapping renewal packet is formatted identically to an original mapping request; from the point of view of the client it is a renewal of an existing mapping, but from the point of view of the PCP server it appears as a new mapping request. Wing Expires June 18, 2011 [Page 26] Internet-Draft Port Control Protocol (PCP) December 2010 This self-healing property of the protocol is very important. When a client renews its port mappings as the result of receiving a packet where the Epoch field indicates that a reboot or similar loss of state has occurred, the client MUST first delay by a random amount of time selected with uniform random distribution in the range 0 to 5 seconds, and then send its first PCP request. After that request is acknowledged by the PCP server, the client may then send its second request, and so on, as rapidly as the gateway allows. The requests SHOULD be issued serially, one at a time; the client SHOULD NOT issue multiple requests simultaneously in parallel. [Ed. Note: the paragraph above is copied from NAT-PMP, and seems to be advice specific to receiving asynchronous notification that the Epoch was reset. Asynchronous notification needs the delay described (in fact, it probably needs greater delay than 0-5 seconds if on a larger network) and also needs to discourage sending multiple PCP requests serially. However, PCP does not have asynchronous notification (yet), and has different needs/ requirements for pacing. In short: the above paragraph needs some discussion.] The discussion in this section focuses on recreating inbound port mappings after loss of PCP server state, because that is the more serious problem. Losing port mappings for outgoing connections destroys those currently active connections, but does not prevent clients from establishing new outgoing connections. In contrast, losing inbound port mappings not only destroys all existing inbound connections, but also prevents the reception of any new inbound connections until the port mapping is recreated. Accordingly, we consider recovery of inbound port mappings the more important priority. However, clients that want outgoing connections to survive a NAT gateway reboot can also achieve that using PCP. After initiating an outbound TCP connection (which will cause the NAT gateway to establish an implicit port mapping) the client should send the NAT gateway a port mapping request for the source port of its TCP connection, which will cause the NAT gateway to send a response giving the external port it allocated for that mapping. The client can then store this information, and use it later to recreate the mapping if it determines that the NAT gateway has lost its mapping state. 7.8.3. Maintaining Pinholes A PCP client can refresh a pinhole by sending a new PCP request containing information from the earlier PCP response. The PCP server will respond indicating the new lifetime. It is possible, due to failure of the PCP server, that the public IP address and/or public Wing Expires June 18, 2011 [Page 27] Internet-Draft Port Control Protocol (PCP) December 2010 port, or the PCP server itself, has changed (due to a new route to a different PCP server). To detect such events more quickly, the PCP client may find it beneficial to use shorter lifetimes (so that it communicates with the PCP server more often). If the PCP client has several pinholes, the Epoch value only needs to be retrieved for one of them to verify the PCP server has not lost port forwarding state. If the client wishes to check the PCP server's Epoch, it sends a PCP request for any one of the client's pinholes. This will return the current Epoch value. In that request the PCP client could extend the mapping lifetime (by asking for more time) or maintain the current lifetime (by asking for the same number of seconds that it knows are remaining of the lifetime). 7.9. Nested NATs [Ed. Note: Nested NATs will be discussed in a later version of this document or, more likely, in a separate document. The mechanism to support nested NATs is to have each NAT implement a PCP server (to service devices and NATs behind it) and a PCP client (to communicate with NATs above it). This allows a PCP client to be unaware of the PCP communications going on between upstream NATs.] 7.10. Pinhole Deletion A PCP Client can delete a pinhole immediately by sending the appropriate PIN OpCode with a lifetime of 0. The PCP server responds by returning a PIN Response with a lifetime of 0. To delete all pinholes for all hosts associated with this subscriber, an all-zero internal IP address is used. 7.11. Pinhole Lifetime Extension An existing mapping can have its lifetime extended by the PCP client. To do this, the PCP client sends a new PCP map request to the server indicating the internal IP address and port(s). The PCP Client SHOULD renew the mapping before its expiry time, otherwise it will be removed by the PCP Server (see Section 7.4.3). In order to prevent excessive PCP chatter, it is RECOMMENDED to renew only 60 seconds before expiration time (to account for retransmissions that might be necessary due to packet loss, clock synchronization between PCP client and PCP server, and so on). Wing Expires June 18, 2011 [Page 28] Internet-Draft Port Control Protocol (PCP) December 2010 8. Deployment Scenarios 8.1. Dual Stack-Lite The interesting components in a Dual-Stack Lite deployment are the B4 element (which is the customer premise router) and the AFTR element (which is the device that both terminates the IPv6-over-IPv4 tunnel and also implements the large-scale NAT44 function). The B4 element does not need to perform a NAT function (and usually does not perform a NAT function), but it does operate its own DHCP server and is the local network's default router. 8.1.1. Overview Various PCP deployment scenarios can be considered to control the PCP server embedded in the AFTR element: 1. UPnP IGD and NAT-PMP are used in the LAN: an interworking function is required to be embedded in the B4 element to ensure interworking between the protocol used in the LAN and PCP. UPnP IGD-PCP Interworking Function is described in Section 9. 2. Hosts behind the B4 element with either include a PCP client or UPnP IGD client. A. if a UPnP IGD client, the B4 element will need to include an interworking function from UPnP IGD to PCP. B. if a PCP client, the PCP client will communicate directly with the PCP server. 3. The B4 element include a PCP Client which is invoked by an HTTP- based configuration (as is common today). The internal-IP- address in the PCP payload would be the internal host used in the port forwarding configuration. Two modes are identified to forward PCP packets to a PCP Server controlling the provisioned AFTR as described in the following sub- sections. [Ed. Note: We need to decide on Encapsulation Mode or Plain IPv6 Mode.] 8.1.2. Encapsulation Mode In this mode, B4 element does no processing at all of the PCP messages, and forwards them as any other UDP traffic. With DS-Lite, this means that IPv4 PCP messages issued by internal PCP Clients are Wing Expires June 18, 2011 [Page 29] Internet-Draft Port Control Protocol (PCP) December 2010 encapsulated into the IPv6 tunnel sent to the AFTR as for any other IPv4 packets. The AFTR decapsulates the IPv4 packets and processes the PCP requests (because the destination IPv4 address points to the PCP Server embedded in the AFTR). 8.1.3. Plain IPv6 Mode Another alternative for deployment of PCP in a DS-Lite context is to rely on a PCP Proxy in the B4 element. Protocol exchanges between the PCP Proxy and the PCP Server are conveyed using plain IPv6 (no tunnelling is used). Nevertheless, the IPv6 address used as source address by the PCP Proxy MUST be the same as the one used by the B4 element. 8.2. NAT64 Hosts behind a NAT64 device can make use of PCP in order to perform port reservation (to get a publicly routable IPv4 port). If the IANA-assigned IP address is used for the discovery of the PCP Server, that IPv4 address can be placed into the IPv6 destination address following that particular network's well-known prefix or network-specific prefix, per [RFC6052]. 8.3. NAT44 and NAT444 Residential subscribers in NAT44 (and NAT444) deployments are usually given one IPv4 address, but may also be given several IPv4 addresses. These addresses are not routable on the IPv4 Internet, but are routable between the subscriber's home and the ISP's large scale NAT (LSN). To accomodate multiple hosts within a home, especially when provided insufficient IPv4 addresses for the number of devices in the home, subscribers operate a NAPT device. When this occurs in conjunction with an upstream NAT44, this is nicknamed "NAT444". [Ed. Note: Does PCP need a mechanism to detect a non-PCP- supporting NAT between a PCP client and a PCP server? Or can that problem be detected by relying on the failure of PCP Server Discovery?] 8.4. IPv6 Firewall See Section 7.5.1. [Ed. Note: this IPv6 firewall section needs more text.] Wing Expires June 18, 2011 [Page 30] Internet-Draft Port Control Protocol (PCP) December 2010 9. Interworking with UPnP IGD 1.0 and 2.0 [Ed. Note: This UPnP IGD Interworking section will likely be moved to a separate document which will fully describe how a proxy needs to translate UPnP IGD messages into PCP messages.] The following diagram shows how UPnP IGD can be interworked with PCP, using an interworking function (IWF). +-------------+ | IGD Control | | Point |-----+ +-------------+ | +---------+ +--------+ +---| IGD-PCP | | PCP | | IWF +-------+ Server |-- +---| | | | +-------------+ | +---------+ +--------+ | Local Host |-----+ +-------------+ | | | | LAN Side | WAN side | <======UPnP IGD=============>|<========PCP=====>| Figure 12: Network Diagram, Interworking UPnP IGD and PCP 9.1. UPnP IGD 1.0 with AddPortMapping Action In UPnP IGD 1.0 [IGD] it is only possible to request a specific port using the AddPortMapping action. Requiring a specific port is incompatible with both (1) a large-scale NAT and with (2) widely- deployed applications. Regarding (1), another subscriber is likely to already be using the same port, so it will be unavailable to this application to operate a server. Regarding (2), if the same popular application exists on two devices behind the same NAPT, they cannot both get the same port. PCP cannot correct this behavior of UPnP IGD:1, but PCP does work with this behavior. Due to this incompatibility with large-scale address sharing and popular applications, future hosts and applications will either support UPnP IGD 2.0's AddAnyPort Mapping (see Section 9.2) or will support PCP. When a requested port assignment fails, most UPnP IGD control points will retry the port assignment requesting the next higher port or requesting a random port. These UPnP IGD requests are translated to PCP requests and sent to the PCP server. The requests include the HONOR_EXTERNAL_PORT option, which causes the PCP server to return an Wing Expires June 18, 2011 [Page 31] Internet-Draft Port Control Protocol (PCP) December 2010 error if it cannot allocate the requested port. The interworking function translates the PCP error response to a UPnP IGD error response. This repeats until the UPnP IGD client gives up or until the PCP server is able to return the requested port. Message flow would be similar to this: UPnP Control Point in-home CPE PCP server | | | |-UPnP:AddPortMapping(80)--->| | | |-PCP:request port 80------>| | | HONOR_EXTERNAL_PORT | | | | | |<-PCP:error----------------| |<-UPnP: unavailable---------| | | | | |-UPnP:AddPortMapping(3213)->| | | |-PCP:request port 3213---->| | | HONOR_EXTERNAL_PORT | | | | | |<-PCP:error----------------| |<-UPnP: unavailable---------| | | | | ... ... ... ... | | | |-UPnP:AddPortMapping(8921)->| | | |-PCP:request port 8921---->| | | HONOR_EXTERNAL_PORT | | | | | |<-PCP:ok, port 8921--------| |<-UPnP: ok, port 8921-------| | | | | Figure 13: Message Flow: Interworking from UPnP IGD 1.0 AddPortMapping action to PCP 9.2. UPnP IGD 2.0 with AddAnyPortMapping Action If the UPnP IGD control point and the UPnP IGD interworking function both implement UPnP IGD 2.0 [IGD-2] and the UPnP IGD control point uses IGD 2's new AddAnyPortMapping action, only one round-trip is necessary. This is because AddAnyPortMapping has semantics similar to PCP's semantics, allowing the PCP server to assign any port. Wing Expires June 18, 2011 [Page 32] Internet-Draft Port Control Protocol (PCP) December 2010 Message flow would be similar to this: UPnP Control Point in-home CPE PCP server | | | |-UPnP:AddAnyPortMapping()->| | | |-PCP:external port 0----->| | |<-PCP:external port=12345-| |<-UPnP:port=12345----------| | | | | Figure 14: Message Flow: Interworking from UPnP IGD 2.0 AddAnyPortMapping action to PCP 9.3. Lifetime Maintenance Neither UPnP IGD 1.0 nor 2.0 provide a lifetime. Thus, the UPnP IGD/ PCP interworking function is responsible for extending the lifetime of mappings that are still interesting to the UPnP IGD control point. Note: It can be an implementation advantage, where possible, for the UPnP IGD/PCP interworking function to request a port mapping lifetime only while that client is active and connected. For example, creating a PCP mapping that is equal to the client's remaining DHCP lifetime is one useful approach. The UPnP IGD/PCP interworking function is responsible for renewing the PCP lifetime as necessary. For clients not using DHCP, other mechanisms to check on the client host's liveliness can also be useful (e.g., ping, ARP, or WiFi association) can be used to discern liveliness of the UPnP IGD control point. However, it is NOT RECOMMENDED to attempt to connect to the TCP or UDP port opened on the control point to determine if the host still wants to receive packets, as the server could be temporarily down when tested, causing a false negative. 10. Security Considerations 11. IANA Considerations IANA is requested to perform the following actions: 11.1. PCP Server IP address IANA shall assign an IPv4 and an IPv6 address for PCP discovery. [Ed. Note: perhaps we can use the AFTR element's IPv4 address? But still need an IPv6 address assigned for PIN64 and PIN66.] Wing Expires June 18, 2011 [Page 33] Internet-Draft Port Control Protocol (PCP) December 2010 11.2. Port Number Need a UDP port allocated. 11.3. OpCodes IANA shall create a new protocol registry for PCP OpCodes, initially populared with the values in Figure 7. New OpCodes can be created via Standards Action [RFC5226]. 11.4. Result Codes IANA shall create a new registry for PCP result codes, numbered 0-255, initially populated with the error codes from both Figure 6 and Figure 10. New Result Codes can be created via Specification Required [RFC5226]. 11.5. Options IANA shall create a new registry for PCP Options, numbered 0-255 with an associated mnemonic. The values 0-127 are optional-to-process, and 128-255 are mandatory-to-process. The initial registry contains the options described in Section 7.5. New information elements in the range 0-64 and 128-192 can be created via Standards Action [RFC5226], and the range 64-127 and 192-255 is for Private Use [RFC5226]. Wing Expires June 18, 2011 [Page 34] Internet-Draft Port Control Protocol (PCP) December 2010 12. Authors The following individuals contributed substantial text to this document and are listed in alphabetical order: Mohamed Boucadair France Telecom Email: mohamed.boucadair@orange-ftgroup.com Stuart Cheshire Apple Inc. 1 Infinite Loop Cupertino, California 95014 USA Phone: +1 408 974 3207 EMail: cheshire@apple.com Francis Dupont ISC Email: Francis.Dupont@fdupont.fr Reinaldo Penno Juniper Networks Email: rpenno@juniper.net 13. Acknowledgments Thanks to Alain Durand, Christian Jacquenet, and Simon Perreault for their comments and review. Thanks to Simon Perreault for highlighting the interaction of dynamic connections with PCP-created pinholes. 14. References 14.1. Normative References [I-D.ietf-behave-v6v4-xlate] Li, X., Bao, C., and F. Baker, "IP/ICMP Translation Algorithm", draft-ietf-behave-v6v4-xlate-23 (work in progress), September 2010. [I-D.ietf-behave-v6v4-xlate-stateful] Bagnulo, M., Matthews, P., and I. Beijnum, "Stateful NAT64: Network Address and Protocol Translation from IPv6 Clients to IPv4 Servers", draft-ietf-behave-v6v4-xlate-stateful-12 (work in progress), July 2010. Wing Expires June 18, 2011 [Page 35] Internet-Draft Port Control Protocol (PCP) December 2010 [I-D.ietf-softwire-dual-stack-lite] Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual- Stack Lite Broadband Deployments Following IPv4 Exhaustion", draft-ietf-softwire-dual-stack-lite-06 (work in progress), August 2010. [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC4193] Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast Addresses", RFC 4193, October 2005. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. [RFC6052] Bao, C., Huitema, C., Bagnulo, M., Boucadair, M., and X. Li, "IPv6 Addressing of IPv4/IPv6 Translators", RFC 6052, October 2010. [proto_numbers] IANA, "Protocol Numbers", 2010, . 14.2. Informative References [I-D.arkko-dual-stack-extra-lite] Arkko, J. and L. Eggert, "Scalable Operation of Address Translators with Per-Interface Bindings", draft-arkko-dual-stack-extra-lite-03 (work in progress), October 2010. [I-D.ietf-behave-lsn-requirements] Yamagata, I., Miyakawa, S., Nakagawa, A., and H. Ashida, "Common requirements for IP address sharing schemes", draft-ietf-behave-lsn-requirements-00 (work in progress), October 2010. [I-D.ietf-v6ops-cpe-simple-security] Woodyatt, J., "Recommended Simple Security Capabilities in Customer Premises Equipment for Providing Residential IPv6 Internet Service", draft-ietf-v6ops-cpe-simple-security-16 (work in progress), October 2010. [I-D.miles-behave-l2nat] Miles, D. and M. Townsley, "Layer2-Aware NAT", draft-miles-behave-l2nat-00 (work in progress), March 2009. Wing Expires June 18, 2011 [Page 36] Internet-Draft Port Control Protocol (PCP) December 2010 [IGD] UPnP Gateway Committee, "WANIPConnection:1", November 2001, . [IGD-2] UPnP Gateway Committee, "Internet Gateway Device (IGD) V 2.0", September 2010, . [RFC0793] Postel, J., "Transmission Control Protocol", STD 7, RFC 793, September 1981. [RFC2608] Guttman, E., Perkins, C., Veizades, J., and M. Day, "Service Location Protocol, Version 2", RFC 2608, June 1999. [RFC3424] Daigle, L. and IAB, "IAB Considerations for UNilateral Self-Address Fixing (UNSAF) Across Network Address Translation", RFC 3424, November 2002. [RFC4787] Audet, F. and C. Jennings, "Network Address Translation (NAT) Behavioral Requirements for Unicast UDP", BCP 127, RFC 4787, January 2007. Appendix A. Changes A.1. Changes from -00 to -01 o Significant document reorganization, primarily to split base PCP operation from OpCode operation. o packet format changed to move 'protocol' outside of PCP common header and into the PIN* opcodes o Renamed Informational Elements (IE) to Options. o Added REMOTE_PEER, REMOTE_PEER_FILTER, and HONOR_EXTERNAL_PORT options. o Is NAT or router behind B4 in scope? o PCP option MAY be included in a request, in which case it MUST appear in a response. It MUST NOT appear in a response if it wasn't in the request. o Response code most significant bit now indicates permanent/ temporary error Wing Expires June 18, 2011 [Page 37] Internet-Draft Port Control Protocol (PCP) December 2010 o PCP Options are split into mandatory-to-process ("P" bit), and into Specification Required and Private Use. o Epoch discussion simplified. Appendix B. Analysis of Techniques to Discover PCP Server [Ed. Note: This Appendix will be removed in a later version of this document. It is included here for reference and discussion purposes.] Discussion Note: A deployment model is a non-PCP aware NAT in a home, and a PCP-aware large scale NAT (LSN) operated by the ISP. This could work by having the host use UPnP IGD with the in-home NAT, and the host use PCP with the LSN. But this deployment model is impossible with several of the mechanisms below. Is this deployment model important, or can we wait for PCP to be enabled on CPE? Several mechanisms for discovering the PCP Server can be envisaged as listed below: 1. A special-purpose IPv4 or IPv6 address, assigned by IANA, which is routed normally until it hits a PCP Server, which responds. Analysis: This solution can be deployed in the context of DS- Lite architecture. Concretely, a well-known IPv4 address can be used to reach a PCP Server embedded in the device that embeds the AFTR capabilities. Since all IPv4 messages issued by a DS-Lite CP router will be encapsulated in IPv6, no state synchronisation issues will be experienced because PCP messages will be handled by the appropriate PCP Server. In some deployment scenarios (e.g., deployment of several stateful NAT64/NAT46 in the same domain), the use of this address is not recommended since PCP messages, issued by a given host, may be handled by a PCP Server embedded in a NAT node which is not involved to handle IP packets issued from that host. The use of this special-purpose IP address may induce session failures and therefore the customer may experience troubles when accessing its services. Consequently, the use of a special-purpose IPv4 address is suitable for DS-Lite NAT44. As for NAT46/NAT64, this is left to the Service Providers according to their deployment configuration. Wing Expires June 18, 2011 [Page 38] Internet-Draft Port Control Protocol (PCP) December 2010 The special-use address MUST NOT be advertised in the global routing table. Packets with that destination address SHOULD be filtered so they are not transmitted on the Internet. 2. Assume the default router is a PCP Server, and send PCP packets to the IP address of the default router. Analysis: This solution is not suitable for DS-Lite NAT44 nor for all variants of NAT64/NAT46. In the context of DS-Lite: There is no default IPv4 router configured in the CP router. All outgoing IPv4 traffic is encapsulated in IPv6 and then forwarded to a pre-configured DS-Lite AFTR device. Furthermore, if IPv6 is used to reach the PCP Server, the first router may not be the one which embeds the AFTR. For NAT64/NAT46 scenarios: The NAT function is not embedded in the first router, therefore this solution candidate does not allow to discover a valid PCP Server. Therefore, this alternative is not recommended. 3. Service Location Protocol (SLP [RFC2608]). Analysis: This solution is not suitable in scenarios where multicast is not enabled. SLP is a chatty protocol. This alternative is not recommended. 4. NAPTR. The host would issue a DNS query for a NAPTR record, formed from some bits of the host's IPv4 or IPv6 address. For example, a host with the IPv6 address 2001:db8:1:2:3:4:567:89ab would first send an NAPTR query for 3.0.0.0.2.0.0.0.1.0.0.0.8.b.d.0.1.0.0.2.IP6.ARPA (20 elements, representing a /64 network prefix), which returns the PCP Server's IPv6 address. A similar scheme can be used with IPv4 using, for example, the first 24 bits of the IPv4 address. Analysis: This solution candidate requires more configuration effort by the Service Provider so as to redirect a given client to the appropriate PCP Server. Any change of the engineering policies (e.g., introduce new LSN device, load- based dimensioning, load-balancing, etc.) would require to update the zone configuration. This would be a hurdle for the flexibility of the operational networks. Adherence to DNS is not encouraged and means which allows for more flexibility are to be promoted. Wing Expires June 18, 2011 [Page 39] Internet-Draft Port Control Protocol (PCP) December 2010 Therefore, this mechanism is not recommended. 5. New DHCPv6/DHCP option and/or a RA option to convey an FQDN of a PCP Server. Analysis: Since DS-Lite and NAT64/NAT46 are likely to be deployed in provider-provisioned environments, DHCP (both DHCPv6 and IPv4 DHCP) is convenient to provision the address/ FQDN of the PCP Server. Author's Address Dan Wing Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134 USA Email: dwing@cisco.com Wing Expires June 18, 2011 [Page 40]