TOC 
MPLS Working GroupM. Bocci, Ed.
Internet-DraftAlcatel-Lucent
Intended status: InformationalS. Bryant, Ed.
Expires: August 2, 2010D. Frost
 Cisco Systems
 L. Levrau
 Alcatel-Lucent
 L. Berger
 LabN
 January 29, 2010


A Framework for MPLS in Transport Networks
draft-ietf-mpls-tp-framework-09

Abstract

This document specifies an architectural framework for the application of Multiprotocol Label Switching (MPLS) to the construction of packet-switched transport networks. It describes a common set of protocol functions - the MPLS Transport Profile (MPLS-TP) - that supports the operational models and capabilities typical of such networks, including signalled or explicitly provisioned bi-directional connection-oriented paths, protection and restoration mechanisms, comprehensive Operations, Administration and Maintenance (OAM) functions, and network operation in the absence of a dynamic control plane or IP forwarding support. Some of these functions are defined in existing MPLS specifications, while others require extensions to existing specifications to meet the requirements of the MPLS-TP.

This document defines the subset of the MPLS-TP applicable in general and to point-to-point paths. The remaining subset, applicable specifically to point-to-multipoint paths, are out of scope of this document.

This document is a product of a joint Internet Engineering Task Force (IETF) / International Telecommunications Union Telecommunications Standardization Sector (ITU-T) effort to include an MPLS Transport Profile within the IETF MPLS and PWE3 architectures to support the capabilities and functionalities of a packet transport network as defined by the ITU-T.

Status of This Memo

This Internet-Draft is submitted to IETF in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as “work in progress.”

The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt.

The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html.

This Internet-Draft will expire on August 2, 2010.

Copyright Notice

Copyright (c) 2010 IETF Trust and the persons identified as the document authors. All rights reserved.

This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the BSD License.



Table of Contents

1.  Introduction
    1.1.  Motivation and Background
    1.2.  Scope
    1.3.  Terminology
        1.3.1.  Transport Network
        1.3.2.  MPLS Transport Profile
        1.3.3.  MPLS-TP Section
        1.3.4.  MPLS-TP Label Switched Path
        1.3.5.  MPLS-TP Label Switching Router (LSR) and Label Edge Router (LER)
        1.3.6.  Customer Edge (CE)
        1.3.7.  Edge-to-Edge LSP
        1.3.8.  Service LSP
        1.3.9.  Layer Network
        1.3.10.  Additional Definitions and Terminology
    1.4.  Applicability
2.  MPLS Transport Profile Requirements
3.  MPLS Transport Profile Overview
    3.1.  Packet Transport Services
    3.2.  Scope of the MPLS Transport Profile
    3.3.  Architecture
        3.3.1.  MPLS-TP Client Adaptation Functions
        3.3.2.  MPLS-TP Forwarding Functions
    3.4.  MPLS-TP Native Services
        3.4.1.  MPLS-TP Client/Server Relationship
        3.4.2.  Pseudowire Adaptation
        3.4.3.  Network Layer Adaptation
    3.5.  Identifiers
    3.6.  Generic Associated Channel (G-ACh)
    3.7.  Operations, Administration and Maintenance (OAM)
    3.8.  LSP Return Path
        3.8.1.  Return Path Types
        3.8.2.  Point-to-Point Unidirectional LSPs
        3.8.3.  Point-to-Point Associated Bidirectional LSPs
        3.8.4.  Point-to-Point Co-Routed Bidirectional LSPs
    3.9.  Control Plane
    3.10.  Inter-domain Connectivity
    3.11.  Static Operation of LSPs and PWs
    3.12.  Survivability
    3.13.  Path Segment Tunnels
        3.13.1.  Provisioning of PST
    3.14.  Pseudowire Segment Tunnels
    3.15.  Network Management
4.  Security Considerations
5.  IANA Considerations
6.  Acknowledgements
7.  Open Issues
8.  References
    8.1.  Normative References
    8.2.  Informative References




 TOC 

1.  Introduction



 TOC 

1.1.  Motivation and Background

This document describes an architectural framework for the application of MPLS to the construction of packet-switched transport networks. It specifies the common set of protocol functions that meet the requirements in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.), and that together constitute the MPLS Transport Profile (MPLS-TP) for point-to-point paths. The remaining MPLS-TP functions, applicable specifically to point-to-multipoint paths, are out of scope of this document.

Historically the optical transport infrastructure - Synchronous Optical Network/Synchronous Digital Hierarchy (SONET/SDH) and Optical Transport Network (OTN) - has provided carriers with a high benchmark for reliability and operational simplicity. To achieve this, transport technologies have been designed with specific characteristics:

Carriers wish to evolve such transport networks to take advantage of the flexibility and cost benefits of packet switching technology and to support packet based services more efficiently. While MPLS is a maturing packet technology that already plays an important role in transport networks and services, not all MPLS capabilities and mechanisms are needed in or consistent with the transport network operational model. There are also transport technology characteristics that are not currently reflected in MPLS.

There are thus two objectives for MPLS-TP:

  1. To enable MPLS to be deployed in a transport network and operated in a similar manner to existing transport technologies.
  2. To enable MPLS to support packet transport services with a similar degree of predictability to that found in existing transport networks.

In order to achieve these objectives, there is a need to define a common set of MPLS protocol functions - an MPLS Transport Profile - for the use of MPLS in transport networks and applications. Some of the necessary functions are provided by existing MPLS specifications, while others require additions to the MPLS tool-set. Such additions should, wherever possible, be applicable to MPLS networks in general as well as those that conform strictly to the transport network model.

This document is a product of a joint Internet Engineering Task Force (IETF) / International Telecommunications Union Telecommunications Standardization Sector (ITU-T) effort to include an MPLS Transport Profile within the IETF MPLS and PWE3 architectures to support the capabilities and functionalities of a packet transport network as defined by the ITU-T.



 TOC 

1.2.  Scope

This document describes an architectural framework for the application of MPLS to the construction of packet-switched transport networks. It specifies the common set of protocol functions that meet the requirements in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.), and that together constitute the MPLS Transport Profile (MPLS-TP) for point-to-point MPLS-TP transport paths. The remaining MPLS-TP functions, applicable specifically to point-to-multipoint transport paths, are out of scope of this document.



 TOC 

1.3.  Terminology

TermDefinition
LSP Label Switched Path
MPLS-TP MPLS Transport Profile
SDH Synchronous Digital Hierarchy
ATM Asynchronous Transfer Mode
OTN Optical Transport Network
cl-ps Connectionless - Packet Switched
co-cs Connection Oriented - Circuit Switched
co-ps Connection Oriented - Packet Switched
OAM Operations, Administration and Maintenance
G-ACh Generic Associated Channel
GAL Generic Alert Label
MEP Maintenance End Point
MIP Maintenance Intermediate Point
APS Automatic Protection Switching
SCC Signalling Communication Channel
MCC Management Communication Channel
EMF Equipment Management Function
FM Fault Management
CM Configuration Management
PM Performance Management
LSR Label Switching Router
MPLS-TP PE MPLS-TP Provider Edge LSR
MPLS-TP P MPLS-TP Provider LSR
PW Pseudowire
Adaptation The mapping of client information into a format suitable for transport by the server layer
Native Service The traffic belonging to the client of the MPLS-TP network
T-PE PW Terminating Provider Edge
S-PE PW Switching provider Edge



 TOC 

1.3.1.  Transport Network

A Transport Network provides transparent transmission of client user plane traffic between attached client devices by establishing and maintaining point-to-point or point-to-multipoint connections between such devices. The architecture of networks supporting point to multipoint connections is out of scope of this document. A Transport Network is independent of any higher-layer network that may exist between clients, except to the extent required to supply this transmission service. In addition to client traffic, a Transport Network may carry traffic to facilitate its own operation, such as that required to support connection control, network management, and Operations, Administration and Maintenance (OAM) functions.

See also the definition of Packet Transport Service in Section 3.1 (Packet Transport Services).



 TOC 

1.3.2.  MPLS Transport Profile

The MPLS Transport Profile (MPLS-TP) is the subset of MPLS functions that meet the requirements in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.). Note that MPLS is defined to include any present and future MPLS capability specified by the IETF, including those capabilities specifically added to support transport network requirements [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.).



 TOC 

1.3.3.  MPLS-TP Section

An MPLS-TP Section is defined in Section 1.2.2 of [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.).



 TOC 

1.3.4.  MPLS-TP Label Switched Path

An MPLS-TP Label Switched Path (MPLS-TP LSP) is an LSP that uses a subset of the capabilities of an MPLS LSP in order to meet the requirements of an MPLS transport network as set out in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.). The characteristics of an MPLS-TP LSP are primarily that it:

  1. Uses a subset of the MPLS OAM tools defined as described in [I‑D.ietf‑mpls‑tp‑oam‑framework] (Allan, D., Busi, I., Niven-Jenkins, B., Fulignoli, A., Hernandez-Valencia, E., Levrau, L., Mohan, D., Sestito, V., Sprecher, N., Helvoort, H., Vigoureux, M., Weingarten, Y., and R. Winter, “MPLS-TP OAM Framework,” April 2010.).
  2. Supports 1+1, 1:1, and 1:N protection functions.
  3. Is traffic engineered.
  4. May be established and maintained via the management plane, or using GMPLS protocols when a control plane is used.
  5. Is either point-to-point or point-to-multipoint. Multipoint to point and multipoint to multipoint LSPs are not permitted.

Note that an MPLS LSP is defined to include any present and future MPLS capability, including those specifically added to support the transport network requirements.



 TOC 

1.3.5.  MPLS-TP Label Switching Router (LSR) and Label Edge Router (LER)

An MPLS-TP Label Switching Router (LSR) is either an MPLS-TP Provider Edge (PE) router or an MPLS-TP Provider (P) router for a given LSP, as defined below. The terms MPLS-TP PE router and MPLS-TP P router describe logical functions; a specific node may undertake only one of these roles on a given LSP.

Note that the use of the term "router" in this context is historic and neither requires nor precludes the ability to perform IP forwarding.



 TOC 

1.3.5.1.  MPLS-TP Provider Edge (PE) Router

An MPLS-TP Provider Edge (PE) router is an MPLS-TP LSR that adapts client traffic and encapsulates it to be transported over an MPLS-TP LSP. Encapsulation may be as simple as pushing a label, or it may require the use of a pseudowire. An MPLS-TP PE exists at the interface between a pair of layer networks. For an MS-PW, an MPLS-TP PE may be either an S-PE or a T-PE, as defined in [RFC5659] (Bocci, M. and S. Bryant, “An Architecture for Multi-Segment Pseudowire Emulation Edge-to-Edge,” October 2009.).



 TOC 

1.3.5.2.  MPLS-TP Provider (P) Router

An MPLS-TP Provider router is an MPLS-TP LSR that does not provide MPLS-TP PE functionality for a given LSP. An MPLS-TP P router switches LSPs which carry client traffic, but does not adapt client traffic and encapsulate it to be carried over an MPLS-TP LSP.



 TOC 

1.3.5.3.  Label Edge Router (LER)

An LSR that exists at the endpoints of an LSP and therefore pushes or pops a label, i.e. does not perform a label swap on the particular LSP under consideration.



 TOC 

1.3.6.  Customer Edge (CE)

A Customer Edge (CE) is the client function sourcing or sinking native service traffic to or from the MPLS-TP network. CEs on either side of the MPLS-TP network are peers and view the MPLS-TP network as a single point-to-point or point-to-multipoint link.



 TOC 

1.3.7.  Edge-to-Edge LSP

An Edge-to-Edge LSP is an LSP between a pair of PEs that may transit zero of more provider LSRs.



 TOC 

1.3.8.  Service LSP

A service LSP is an LSP that caries a single client service.



 TOC 

1.3.9.  Layer Network

A layer network is defined in [G.805] (, “ITU-T Recommendation G.805 (11/95), "Generic Functional Architecture of Transport Networks",” November 1995.) and described in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.).



 TOC 

1.3.10.  Additional Definitions and Terminology

Detailed definitions and additional terminology may be found in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.).



 TOC 

1.4.  Applicability

MPLS-TP can be used to construct packet transport networks and is therefore applicable in any packet transport network context. It is also applicable to subsets of a packet network where the transport network operational model is deemed attractive. The following are examples of MPLS-TP applicability models:

  1. MPLS-TP provided by a network that only supports MPLS-TP LSPs and PWs (i.e. Only MPLS-TP LSPs and PWs exist between the PEs or LSRs), acting as a server for other layer 1, layer 2 and layer 3 networks (Figure 1 (MPLS-TP Server Layer Example)).
  2. MPLS-TP provided by a network that also supports non-MPLS-TP LSPs and PWs (i.e. both LSPs and PWs that conform to the transport profile and those that do not, exist between the PEs), acting as a server for other layer 1, layer 2 and layer 3 networks (Figure 2 (MPLS-TP in MPLS Network Example)).
  3. MPLS-TP as a server layer for client layer traffic of IP or MPLS networks which do not use functions of the MPLS transport profile. For MPLS traffic, the MPLS-TP server layer network uses PW switching [RFC5659] (Bocci, M. and S. Bryant, “An Architecture for Multi-Segment Pseudowire Emulation Edge-to-Edge,” October 2009.) or LSP stitching [RFC5150] (Ayyangar, A., Kompella, K., Vasseur, JP., and A. Farrel, “Label Switched Path Stitching with Generalized Multiprotocol Label Switching Traffic Engineering (GMPLS TE),” February 2008.) at the PE that terminates the MPLS-TP server layer (Figure 3 (MPLS-TP Transporting Client Service Traffic)).

These models are not mutually exclusive.



MPLS-TP LSP, provided by a network that only supports MPLS-TP, acting as
    a server for other layer 1, layer 2 and layer 3 networks.

            |<-- L1/2/3 -->|<-- MPLS-TP-->|<-- L1/2/3 -->|
                                 Only

                               MPLS-TP
                         +---+   LSP    +---+
          +---+  Client  |   |----------|   | Client   +---+
          |CE1|==Traffic=|PE2|==========|PE3|=Traffic==|CE1|
          +---+          |   |----------|   |          +---+
                         +---+          +---+

  Example  a)  [Ethernet]     [Ethernet]     [Ethernet]
  layering                    [   PW   ]
                              [-TP LSP ]

           b)  [   IP   ]     [  IP    ]     [  IP   ]
                              [ Demux  ]
                              [-TP LSP ]

 Figure 1: MPLS-TP Server Layer Example 



MPLS-TP LSP, provided by a network that also supports non-MPLS-TP
    functions, acting as a server for other layer 1, layer 2 and
    layer 3 networks.

            |<-- L1/2/3 -->|<-- MPLS -->|<-- L1/2/3 -->|

                               MPLS-TP
                         +---+   LSP    +---+
          +---+  Client  |   |----------|   | Client   +---+
          |CE1|==Traffic=|PE2|==========|PE3|=Traffic==|CE1|
          +---+          |   |----------|   |          +---+
                         +---+          +---+

Example  a)  [Ethernet]       [Ethernet]     [Ethernet]
layering                      [   PW   ]
                              [-TP LSP ]

         b)  [   IP   ]       [  IP    ]     [  IP   ]
                              [ Demux  ]
                              [-TP LSP ]

 Figure 2: MPLS-TP in MPLS Network Example 



MPLS-TP as a server layer for client layer traffic of IP or MPLS
    networks which do not use functions of the MPLS transport
    profile.


              |<-- MPLS ---->|<-- MPLS-TP-->|<--- MPLS --->|
                                   Only

  +---+   +----+  Non-TP  +----+  MPLS-TP +----+  Non-TP  +----+   +---+
  |CE1|---|T-PE|====LSP===|S-PE|====LSP===|S-PE|====LSP===|S-PE|---|CE2|
  +---+   +----+          +----+          +----+          +----+   +---+
                       (PW switching)  (PW switching)

(a)  [ Eth ]   [   Eth  ]       [  Eth   ]     [   Eth  ]     [ Eth ]
               [ PW Seg ]       [ PW Seg ]     [ PW Seg ]
               [   LSP  ]       [-TP LSP ]     [   LSP  ]



             |<-- MPLS ---->|<-- MPLS-TP-->|<--- MPLS --->|
                                  Only

  +---+   +----+  Non-TP  +----+  MPLS-TP +----+  Non-TP  +----+   +---+
  |CE1|---| PE |====LSP===| PE |====LSP===| PE |====LSP===| PE |---|CE2|
  +---+   +----+          +----+          +----+          +----+   +---+
                       (LSP stitching) (LSP stitching)

(b)  [ IP ]      [  IP  ]       [   IP   ]     [  IP   ]     [ IP  ]
                 [  LSP ]       [-TP LSP ]     [  LSP  ]

 Figure 3: MPLS-TP Transporting Client Service Traffic 



 TOC 

2.  MPLS Transport Profile Requirements

The requirements for MPLS-TP are specified in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.), [I‑D.ietf‑mpls‑tp‑oam‑requirements] (Vigoureux, M. and D. Ward, “Requirements for OAM in MPLS Transport Networks,” March 2010.), and [I‑D.ietf‑mpls‑tp‑nm‑req] (Mansfield, S. and K. Lam, “MPLS TP Network Management Requirements,” October 2009.). This section provides a brief reminder to guide the reader and is therefore not normative. It is not intended as a substitute for these documents.

MPLS-TP must not modify the MPLS forwarding architecture and must be based on existing pseudowire and LSP constructs.

Point to point LSPs may be unidirectional or bi-directional, and it must be possible to construct congruent Bi-directional LSPs.

MPLS-TP LSPs do not merge with other LSPs at an MPLS-TP LSR and it must be possible to detect if a merged LSP has been created.

It must be possible to forward packets solely based on switching the MPLS or PW label. It must also be possible to establish and maintain LSPs and/or pseudowires both in the absence or presence of a dynamic control plane. When static provisioning is used, there must be no dependency on dynamic routing or signalling.

OAM, protection and forwarding of data packets must be able to operate without IP forwarding support.

It must be possible to monitor LSPs and pseudowires through the use of OAM in the absence of control plane or routing functions. In this case information gained from the OAM functions is used to initiate path recovery actions at either the PW or LSP layers.



 TOC 

3.  MPLS Transport Profile Overview



 TOC 

3.1.  Packet Transport Services

One objective of MPLS-TP is to enable MPLS networks to provide packet transport services with a similar degree of predictability to that found in existing transport networks. Such packet transport services inherit a number of characteristics, defined in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.):

These characteristics imply that a packet transport service does not support a connectionless packet-switched forwarding mode. However, this does not preclude it carrying client traffic associated with a connectionless service.

Such packet transport services are very similar to Layer 2 Virtual Private Networks as defined by the IETF.



 TOC 

3.2.  Scope of the MPLS Transport Profile

Figure 4 (Scope of MPLS-TP) illustrates the scope of MPLS-TP. MPLS-TP solutions are primarily intended for packet transport applications. MPLS-TP is a strict subset of MPLS, and comprises only those functions that are necessary to meet the requirements of [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.). This includes MPLS functions that were defined prior to [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.) but that meet the requirements of [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.), together with additional functions defined to meet those requirements. Some MPLS functions defined before [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.) such as Equal Cost Multi-Path, LDP signalling used in such a way that it creates multipoint-to-point LSPs, and IP forwarding in the data plane are explicitly excluded from MPLS-TP by that requirements specification.

Note that MPLS as a whole will continue to evolve to include additional functions that do not conform to the MPLS Transport Profile or its requirements, and thus fall outside the scope of MPLS-TP.



|<============================== MPLS ==============================>|


|<============= Pre-RFC5654 MPLS ================>|
  {      ECMP       }
  { LDP/non-TE LSPs }
  {     IP fwd      }

                    |<================ MPLS-TP ====================>|
                                                    { Additional }
                                                    {  Transport }
                                                    {  Functions }


 Figure 4: Scope of MPLS-TP 



 TOC 

3.3.  Architecture

MPLS-TP comprises the following architectural elements:

The MPLS-TP architecture for LSPs and PWs includes the following two sets of functions:

The adaptation functions interface the native service to MPLS-TP. This includes the case where the native service is an MPLS-TP LSP.

The forwarding functions comprise the mechanisms required for forwarding the encapsulated client traffic over an MPLS-TP server layer network, for example PW and LSP labels.



 TOC 

3.3.1.  MPLS-TP Client Adaptation Functions

The MPLS-TP native service adaptation functions interface the client service to MPLS-TP. For pseudowires, these adaptation functions are the payload encapsulation described in Section 4.4 of [RFC3985] (Bryant, S. and P. Pate, “Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture,” March 2005.) and Section 6 of [RFC5659] (Bocci, M. and S. Bryant, “An Architecture for Multi-Segment Pseudowire Emulation Edge-to-Edge,” October 2009.). For network layer client services, the adaptation function uses the MPLS encapsulation format as defined in [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.).

The purpose of this encapsulation is to abstract the client service data plane from the MPLS-TP data plane, thus contributing to the independent operation of the MPLS-TP network.

MPLS-TP is itself a client of an underlying server layer. MPLS-TP is thus also bounded by a set of adaptation functions to this server layer network, which may itself be MPLS-TP. These adaptation functions provide encapsulation of the MPLS-TP frames and for the transparent transport of those frames over the server layer network. The MPLS-TP client inherits its Quality of Service (QoS) from the MPLS-TP network, which in turn inherits its QoS from the server layer. The server layer must therefore provide the necessary QoS to ensure that the MPLS-TP client QoS commitments can be satisfied.



 TOC 

3.3.2.  MPLS-TP Forwarding Functions

The forwarding functions comprise the mechanisms required for forwarding the encapsulated client over an MPLS-TP server layer network, for example PW and LSP labels.

MPLS-TP LSPs use the MPLS label switching operations and TTL processing procedures defined in [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.) and [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.). These operations are highly optimised for performance and are not modified by the MPLS-TP profile.

In addition, MPLS-TP PWs use the SS-PW and MS-PW forwarding operations defined in [RFC3985] (Bryant, S. and P. Pate, “Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture,” March 2005.) and [RFC5659] (Bocci, M. and S. Bryant, “An Architecture for Multi-Segment Pseudowire Emulation Edge-to-Edge,” October 2009.). The PW label is processed by a PW forwarder and is always at the bottom of the label stack for a given MPLS-TP layer network.

Per-platform label space is used for PWs. Either per-platform, per-interface or other context-specific label space [RFC5331] (Aggarwal, R., Rekhter, Y., and E. Rosen, “MPLS Upstream Label Assignment and Context-Specific Label Space,” August 2008.) may be used for LSPs.

MPLS-TP forwarding is based on the label that identifies the transport path (LSP or PW). The label value specifies the processing operation to be performed by the next hop at that level of encapsulation. A swap of this label is an atomic operation in which the contents of the packet after the swapped label are opaque to the forwarder. The only event that interrupts a swap operation is TTL expiry. This is a fundamental architectural construct of MPLS to be taken into account when designing protocol extensions that require packets (e.g. OAM packets) to be sent to an intermediate LSR.

Further processing to determine the context of a packet occurs when a swap operation is interrupted in this manner, or a pop operation exposes a specific reserved label at the top of the stack, or the packet is received with the GAL Section 3.6 (Generic Associated Channel (G-ACh)) at the top of stack. Otherwise the packet is forwarded according to the procedures in [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.).

Point-to-point MPLS-TP LSPs can be either unidirectional or bidirectional.

It must be possible to configure an MPLS-TP LSP such that the forward and backward directions of a bidirectional MPLS-TP LSP are co-routed, i.e. follow the same path. The pairing relationship between the forward and the backward directions must be known at each LSR or LER on a bidirectional LSP.

In normal conditions, all the packets sent over a PW or an LSP follow the same path through the network and those that belong to a common ordered aggregate are delivered in order. For example per-packet equal cost multi-path (ECMP) load balancing is not applicable to MPLS-TP LSPs.

Penultimate hop popping (PHP) is disabled on MPLS-TP LSPs by default.

MPLS-TP supports Quality of Service capabilities via the MPLS Differentiated Services (DiffServ) architecture [RFC3270] (Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen, P., Krishnan, R., Cheval, P., and J. Heinanen, “Multi-Protocol Label Switching (MPLS) Support of Differentiated Services,” May 2002.). Both E-LSP and L-LSP MPLS DiffServ modes are supported. The Traffic Class field (formerly the EXP field) of an MPLS label follows the definition and processing rules of [RFC5462] (Andersson, L. and R. Asati, “Multiprotocol Label Switching (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic Class" Field,” February 2009.) and [RFC3270] (Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen, P., Krishnan, R., Cheval, P., and J. Heinanen, “Multi-Protocol Label Switching (MPLS) Support of Differentiated Services,” May 2002.). Note that packet reordering between flows belonging to different traffic classes may occur if more than one traffic class is supported on a single LSP.

Only the Pipe and Short Pipe DiffServ tunnelling and TTL processing models described in [RFC3270] (Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen, P., Krishnan, R., Cheval, P., and J. Heinanen, “Multi-Protocol Label Switching (MPLS) Support of Differentiated Services,” May 2002.) and [RFC3443] (Agarwal, P. and B. Akyol, “Time To Live (TTL) Processing in Multi-Protocol Label Switching (MPLS) Networks,” January 2003.) are supported in MPLS-TP.



 TOC 

3.4.  MPLS-TP Native Services

This document describes the architecture for two types of native service adaptation:

A PW provides any emulated service that the IETF has defined to be provided by a PW, for example Ethernet, Frame Relay, or PPP/HDLC. A registry of PW types is maintained by IANA. When the client adaptation is via a PW, the mechanisms described in Section 3.4.2 (Pseudowire Adaptation) are used.

An MPLS LSP Label can also be used as the adaptation, in which case any client supported by [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.) is allowed, for example a MPLS LSP, PW, or IP. When the client adaptation is via an MPLS label, the mechanisms described in Section 3.4.3 (Network Layer Adaptation) are used.



 TOC 

3.4.1.  MPLS-TP Client/Server Relationship

The MPLS-TP client server relationship is defined by the MPLS-TP network boundary and the label context. It is not explicitly indicated in the packet. In terms of the MPLS label stack, when the client traffic type of the MPLS-TP network is an MPLS LSP or a PW, then the S bits of all the labels in the MPLS-TP label stack carrying that client traffic are zero; otherwise the bottom label of the MPLS-TP label stack has the S bit set to one (i.e. there can only one S bit set in a label stack).

The data plane behaviour of MPLS-TP is the same as the best current practise for MPLS. This includes the setting of the S-Bit. In each case, the S-bit is set to indicate the bottom (i.e. inner-most) label in the label stack that is contiguous between the MPLS-TP server and the client layer. Note that this best current practise differs slightly from [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.) which uses the S-bit to identify when MPLS label processing stops and network layer processing starts.

The relationship of MPLS-TP to its clients is illustrated in Figure 5 (MPLS-TP - Client Relationship).



   PW-Based               MPLS Labelled                IP
   Services                  Services                Transport
 |------------|  |-----------------------------|  |------------|

   Emulated        PW over LSP      IP over LSP         IP
   Service
                  +------------+
                  | PW Payload |
                  +------------+  +------------+               (CLIENTS)
                  |PW Lbl(S=1) |  |     IP     |
 +------------+   +------------+  +------------+  +------------+
 | PW Payload |   |LSP Lbl(S=0)|  |LSP Lbl(S=1)|  |     IP     |
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 |PW Lbl (S=1)|   |LSP Lbl(S=0)|  |LSP Lbl(S=0)|  |LSP Lbl(S=1)|
 +------------+   +------------+  +------------+  +------------+
 |LSP Lbl(S=0)|
 +------------+                                                (MPLS-TP)



~~~~~~~~~~~ denotes Client <-> MPLS-TP layer boundary


Note that in the PW over LSP case the client may omit its LSP Label if

penultimate hop popping has been agreed with its peer

 Figure 5: MPLS-TP - Client Relationship 

The data plane behaviour of MPLS-TP is the same as the best current practise for MPLS. This includes the setting of the S-Bit. In each case, the S-bit is set to indicate the bottom (i.e. inner-most) label in the label stack that is contiguous between the MPLS-TP server and the client layer.

Note that the label stacks shown above are divided between those inside the MPLS-TP Network and those within the client network when the client network is MPLS(-TP). They illustrate the smallest number of labels possible. These label stacks could also include more labels.



 TOC 

3.4.2.  Pseudowire Adaptation

The architecture for an MPLS-TP network that provides PW emulated services is based on the MPLS [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.) and pseudowire [RFC3985] (Bryant, S. and P. Pate, “Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture,” March 2005.) architectures. Multi-segment pseudowires may optionally be used to provide a packet transport service, and their use is consistent with the MPLS-TP architecture. The use of MS-PWs may be motivated by, for example, the requirements specified in [RFC5254] (Bitar, N., Bocci, M., and L. Martini, “Requirements for Multi-Segment Pseudowire Emulation Edge-to-Edge (PWE3),” October 2008.). If MS-PWs are used, then the MS-PW architecture [RFC5659] (Bocci, M. and S. Bryant, “An Architecture for Multi-Segment Pseudowire Emulation Edge-to-Edge,” October 2009.) also applies.

Figure 6 (MPLS-TP Architecture (Single Segment PW)) shows the architecture for an MPLS-TP network using single-segment PWs.



            |<--------------- Emulated Service ----------------->|
            |                                                    |
            |          |<-------- Pseudowire -------->|          |
            |          |      encapsulated, packet    |          |
            |          |      transport service       |          |
            |          |                              |          |
            |          |    |<------ LSP ------->|    |          |
            |          V    V                    V    V          |
            V    AC    +----+      +-----+       +----+     AC   V
      +-----+    |     | PE1|=======\   /========| PE2|     |    +-----+
      |     |----------|.......PW1.| \ / |............|----------|     |
      | CE1 |    |     |    |      |  X  |       |    |     |    | CE2 |
      |     |----------|.......PW2.| / \ |............|----------|     |
      +-----+  ^ |     |    |=======/   \========|    |     | ^  +-----+
            ^  |       +----+      +-----+       +----+       |  ^
            |  |   Provider Edge 1    ^     Provider Edge 2   |  |
            |  |                      |                       |  |
     Customer  |                  P Router                    | Customer
      Edge 1   |                                              |  Edge 2
               |                                              |
               |                                              |
         Native service                                 Native service

 Figure 6: MPLS-TP Architecture (Single Segment PW) 

Figure 7 (MPLS-TP Architecture (Multi-Segment PW)) shows the architecture for an MPLS-TP network when multi-segment pseudowires are used. Note that as in the SS-PW case, P-routers may also exist.



           |<----------- Pseudowire encapsulated ------------->|
           |             packet transport service              |
           |                                                   |
           |                                                   |
           |                                                   |
        AC |     |<-------- LSP1 -------->|    |<--LSP2-->|    | AC
         | V     V                        V    V          V    V |
         | +----+              +-----+    +----+          +----+ |
   +---+ | |TPE1|===============\   /=====|SPE1|==========|TPE2| | +---+
   |   |---|......PW1-Seg1.... | \ / | ......X...PW1-Seg2......|---|   |
   |CE1| | |    |              |  X  |    |    |          |    | | |CE2|
   |   |---|......PW2-Seg1.... | / \ | ......X...PW2-Seg2......|---|   |
   +---+ | |    |===============/   \=====|    |==========|    | | +---+
       ^   +----+     ^        +-----+    +----+     ^    +----+   ^
       |              |          ^                   |             |
       |           TE LSP        |                TE LSP           |
       |                      P-router                             |
       |                                                           |
       |<-------------------- Emulated Service ------------------->|

PW1-segment1 and PW1-segment2 are segments of the same MS-PW,
while PW2-segment1 and PW2-segment2 are segments of another MS-PW

 Figure 7: MPLS-TP Architecture (Multi-Segment PW) 

The corresponding MPLS-TP protocol stacks including PWs are shown in Figure 8 (MPLS-TP Layer Network using Pseudowires). In this figure protocol the Transport Service Layer [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.) is identified by the PW demultiplexer (Demux) label and the Transport Path Layer [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.) is identified by the LSP Demux Label.



 +-------------------+     /===================\   /===================\
 |  Client Layer     |     H     OAM PDU       H   H     OAM PDU       H
 /===================\     H-------------------H   H-------------------H
 H     PW Encap      H     H      GACh         H   H      GACh         H
 H-------------------H     H-------------------H   H-------------------H
 H   PW Demux (S=1)  H     H PW Demux (S=1)    H   H    GAL (S=1)      H
 H-------------------H     H-------------------H   H-------------------H
 H     LSP Demux(s)  H     H  LSP Demux(s)     H   H  LSP Demux(s)     H
 \===================/     \===================/   \===================/
 |    Server Layer   |     |   Server Layer    |   |   Server Layer    |
 +-------------------+     +-------------------+   +-------------------+

     User Traffic                 PW OAM                  LSP OAM

Note: H(ighlighted) indicates the part of the protocol stack we are
considering in this document.

 Figure 8: MPLS-TP Layer Network using Pseudowires 

PWs and their underlying labels may be configured or signaled. See Section 3.11 (Static Operation of LSPs and PWs) for additional details related to configured service types. See Section 3.9 (Control Plane) for additional details related to signaled service types.



 TOC 

3.4.2.1.  Pseudowire Bases Services

When providing a Virtual Private Wire Service (VPWS) , Virtual Private Local Area Network Service (VPLS), Virtual Private Multicast Service (VPMS) or Internet Protocol Local Area Network Service (IPLS) pseudowires must be used to carry the client service. VPWS, VLPS, and IPLS are described in [RFC4664] (Andersson, L. and E. Rosen, “Framework for Layer 2 Virtual Private Networks (L2VPNs),” September 2006.). VPMS is described in [I‑D.ietf‑l2vpn‑vpms‑frmwk‑requirements] (Kamite, Y., JOUNAY, F., Niven-Jenkins, B., Brungard, D., and L. Jin, “Framework and Requirements for Virtual Private Multicast Service (VPMS),” October 2009.)



 TOC 

3.4.3.  Network Layer Adaptation

MPLS-TP LSPs can be used to transport network layer clients. This document uses the term Network Layer in the same sense as it is used in [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.) and [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.). The network layer protocols supported by [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.) and [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.) can be transported between service interfaces. Examples are shown in Figure 5 above. Support for network layer clients follows the MPLS architecture for support of network layer protocols as specified in [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.) and [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.).

With network layer adaptation, the MPLS-TP domain provides either a uni-directional or bidirectional point-to-point connection between two PEs in order to deliver a packet transport service to attached customer edge (CE) nodes. For example, a CE may be an IP, MPLS or MPLS-TP node. As shown in Figure 9 (MPLS-TP Architecture for Network Layer Clients), there is an attachment circuit between the CE node on the left and its corresponding provider edge (PE) node which provides the service interface, a bidirectional LSP across the MPLS-TP network to the corresponding PE node on the right, and an attachment circuit between that PE node and the corresponding CE node for this service.

The attachment circuits may be heterogeneous (e.g., any combination of SDH, PPP, Frame Relay, etc.) and network layer protocol payloads arrive at the service interface encapsulated in the Layer1/Layer2 encoding defined for that access link type. It should be noted that the set of network layer protocols includes MPLS and hence MPLS encoded packets with an MPLS label stack (the client MPLS stack), may appear at the service interface.



            |<------------- Client Network Layer ------------->|
            |                                                  |
            |          |<---- Pkt Xport Service --->|          |
            |          |                            |          |
            |          |    |<-- PSN Tunnel -->|    |          |
            |          V    V                  V    V          |
            V     AC   +----+      +---+       +----+    AC    V
      +-----+     |    |PE1 |      |   |       |PE2 |    |     +-----+
      |     |     |LSP |    |      |   |       |    |    |     |     |
      | CE1 |----------|    |========X=========|    |----------| CE2 |
      |     |  ^  |IP  |    |  ^   |   |   ^   |    |    |  ^  |     |
      +-----+  |  |    |    |  |   |   |   |   |    |    |  |  +-----+
            ^  |       +----+  |   +---+   |   +----+    |  |  ^
            |  |      Provider |     ^     |  Provider      |  |
            |  |       Edge    |     |     |   Edge         |  |
      Customer |        1      | P-router  |    2           | Customer
      Edge 1   |             TE           TE                | Edge 2
               |             LSP          LSP               |
               |                                            |
         Native service                               Native service

 Figure 9: MPLS-TP Architecture for Network Layer Clients 

At the ingress service interface the client packets are received . The PE pushes one or more labels onto the client packets which are then label switched over the transport network. Correspondingly the egress PE pops any labels added by the MPLS-TP networks and transmits the packet for delivery to the attached CE via the egress service interface.



                           /===================\
                           H     OAM PDU       H
 +-------------------+     H-------------------H   /===================\
 |  Client Layer     |     H      GACh         H   H     OAM PDU       H
 /===================\     H-------------------H   H-------------------H
 H    Encap Label    H     H      GAL (S=1)    H   H      GACh         H
 H-------------------H     H-------------------H   H-------------------H
 H   SvcLSP Demux    H     H SvcLSP Demux (S=0)H   H    GAL (S=1)      H
 H-------------------H     H-------------------H   H-------------------H
 H     LSP Demux(s)  H     H  LSP Demux(s)     H   H  LSP Demux(s)     H
 \===================/     \===================/   \===================/
 |   Server Layer    |     |   Server Layer    |   |   Server Layer    |
 +-------------------+     +-------------------+   +-------------------+

     User Traffic            Service LSP OAM               LSP OAM


Note: H(ighlighted) indicates the part of the protocol stack we are
considering in this document.

 Figure 10: Domain of MPLS-TP Layer Network for IP and LSP Clients 

In this figure the Transport Service Layer [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.) is identified by the Service LSP (SvcLSP) demultiplexer (Demux) label and the Transport Path Layer [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.) is identified by the LSP Demux Label. Note that the functions of the Encapsulation label and the Service Label shown above as SvcLSP Demux may be represented by a single label stack entry. Additionally, the S-bit will always be zero when the client layer is MPLS labelled.

Within the MPLS-TP transport network, the network layer protocols are carried over the MPLS-TP network using a logically separate MPLS label stack (the server stack). The server stack is entirely under the control of the nodes within the MPLS-TP transport network and it is not visible outside that network. Figure 10 (Domain of MPLS-TP Layer Network for IP and LSP Clients) shows how a client network protocol stack (which may be an MPLS label stack and payload) is carried over a network layer client service over an MPLS-TP transport network.

A label per network layer protocol payload type that is to be transported is required. When multiple protocol payload types are to be carried over a single service a unique label stack entry must be present for each payload type. Such labels are referred to as "Encapsulation Labels", one of which is shown in Figure 10 (Domain of MPLS-TP Layer Network for IP and LSP Clients). Encapsulation Label may be either configured or signaled.

Both an Encapsulation Label and a Service Label should be present in the label stack when a particular packet transport service is supporting more than one network layer protocol payload type. For example, if both IP and MPLS are to be carried, as shown in Figure 9 (MPLS-TP Architecture for Network Layer Clients), then two Encapsulation Labels are mapped on to a common Service Label.

Note: The Encapsulation Label may be omitted when the transport service is supporting only one network layer protocol payload type. For example, if only MPLS labeled packets are carried over a service, then the Service Label (stack entry) provides both the payload type indication and service identification.

Service labels are typically carried over an MPLS-TP LSP edge-to-edge (or transport path layer). An MPLS-TP edge-to-edge LSP is represented as an LSP Demux label as shown in Figure 10 (Domain of MPLS-TP Layer Network for IP and LSP Clients). An edge-to-edge LSP is commonly used when more than one service exists between two PEs.

Note, the edge-to-edge LSP may be omitted when only one service exists between two PEs. For example, if only one service is carried between two PEs then a single Service Label could be used to provide both the service indication and the MPLS-TP edge-to-edge LSP. Alternatively, if multiple services exist between a pair of PEs then a per-client Service Label would be mapped on to a common MPLS-TP edge-to-edge LSP.

As noted above, the layer 2 and layer 1 protocols used to carry the network layer protocol over the attachment circuits are not transported across the MPLS-TP network. This enables the use of different layer 2 and layer 1 protocols on the two attachment circuits.

At each service interface, Layer 2 addressing must be used to ensure the proper delivery of a network layer packet to the adjacent node. This is typically only an issue for LAN media technologies (e.g., Ethernet) which have Media Access Control (MAC) addresses. In cases where a MAC address is needed, the sending node must set the destination MAC address to an address that ensures delivery to the adjacent node. That is the CE sets the destination MAC address to an address that ensures delivery to the PE, and the PE sets the destination MAC address to an address that ensures delivery to the CE. The specific address used is technology type specific and is not covered in this document. In some technologies the MAC address will need to be configured (Examples for the Ethernet case include a configured unicast MAC address for the adjacent node, or even using the broadcast MAC address when the CE-PE service interface is dedicated. The configured address is then used as the MAC destination address for all packets sent over the service interface.)

Note that when two CEs, which peer with each other, operate over a network layer transport service run a routing protocol such as IS-IS or OSPF some care should be taken to configure the routing protocols to use point- to-point adjacencies .The specifics of such configuration is outside the scope of this document. See [RFC5309] (Shen, N. and A. Zinin, “Point-to-Point Operation over LAN in Link State Routing Protocols,” October 2008.) for additional details.

The CE to CE service types and corresponding labels may be configured or signaled . See Section 3.11 (Static Operation of LSPs and PWs) for additional details related to configured service types. See Section 3.9 (Control Plane) for additional details related to signaled service types.



 TOC 

3.5.  Identifiers

Identifiers are used to uniquely distinguish entities in an MPLS-TP network. These include operators, nodes, LSPs, pseudowires, and their associated maintenance entities. [I‑D.ietf‑mpls‑tp‑identifiers] (Bocci, M. and G. Swallow, “MPLS-TP Identifiers,” March 2010.) defines a set of identifiers that are compatible with existing MPLS control plane identifiers, as well as a set of identifiers that may be used when no IP control plane is available.



 TOC 

3.6.  Generic Associated Channel (G-ACh)

For correct operation of the OAM it is important that the OAM packets fate-share with the data packets. In addition in MPLS-TP it is necessary to discriminate between user data payloads and other types of payload. For example, a packet may be associated with a Signalling Communication Channel (SCC), or a channel used for Automatic Protection Switching (APS) data. This is achieved by carrying such packets on a generic control channel associated to the LSP, PW or section.

MPLS-TP makes use of such a generic associated channel (G-ACh) to support Fault, Configuration, Accounting, Performance and Security (FCAPS) functions by carrying packets related to OAM, APS, SCC, MCC or other packet types in-band over LSPs or PWs. The G-ACh is defined in [RFC5586] (Bocci, M., Vigoureux, M., and S. Bryant, “MPLS Generic Associated Channel,” June 2009.) and is similar to the Pseudowire Associated Channel [RFC4385] (Bryant, S., Swallow, G., Martini, L., and D. McPherson, “Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for Use over an MPLS PSN,” February 2006.), which is used to carry OAM packets over pseudowires. The G-ACh is indicated by a generic associated channel header (ACH), similar to the Pseudowire VCCV control word; this header is present for all Sections, LSPs and PWs making use of FCAPS functions supported by the G-ACh.

For pseudowires, the G-ACh uses the first four bits of the pseudowire control word to provide the initial discrimination between data packets and packets belonging to the associated channel, as described in [RFC4385] (Bryant, S., Swallow, G., Martini, L., and D. McPherson, “Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for Use over an MPLS PSN,” February 2006.). When this first nibble of a packet, immediately following the label at the bottom of stack, has a value of '1', then this packet belongs to a G-ACh. The first 32 bits following the bottom of stack label then have a defined format called an associated channel header (ACH), which further defines the content of the packet. The ACH is therefore both a demultiplexer for G-ACh traffic on the PW, and a discriminator for the type of G-ACh traffic.

When the OAM or other control message is carried over an LSP, rather than over a pseudowire, it is necessary to provide an indication in the packet that the payload is something other than a user data packet. This is achieved by including a reserved label with a value of 13 in the label stack. This reserved label is referred to as the 'Generic Alert Label (GAL)', and is defined in [RFC5586] (Bocci, M., Vigoureux, M., and S. Bryant, “MPLS Generic Associated Channel,” June 2009.). When a GAL is found, it indicates that the payload begins with an ACH. The GAL is thus a demultiplexer for G-ACh traffic on the LSP, and the ACH is a discriminator for the type of traffic carried on the G-ACh. Note however that MPLS-TP forwarding follows the normal MPLS model, and that a GAL is invisible to an LSR unless it is the top label in the label stack. The only other circumstance under which the label stack may be inspected for a GAL is when the TTL has expired. Any MPLS-TP component that intentionally performs this inspection must assume that it is asynchronous with respect to the forwarding of other packets. All operations on the label stack are in accordance with [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.) and [RFC3032] (Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” January 2001.).

In MPLS-TP, the 'G-ACh Alert Label (GAL)' always appears at the bottom of the label stack (i.e. S bit set to 1).

The G-ACh must only be used for channels that are an adjunct to the data service. Examples of these are OAM, APS, MCC and SCC, but the use is not restricted to these services. The G-ACh must not be used to carry additional data for use in the forwarding path, i.e. it must not be used as an alternative to a PW control word, or to define a PW type.

At the server layer, bandwidth and QoS commitments apply to the gross traffic on the LSP, PW or section. Since the G-ACh traffic is indistinguishable from the user data traffic, protocols using the G-ACh must take into consideration the impact they have on the user data that they are sharing resources with. Conversely, capacity must be made available for important G-ACh uses such as protection and OAM. In addition, protocols using the G-ACh must conform to the security and congestion considerations described in [RFC5586] (Bocci, M., Vigoureux, M., and S. Bryant, “MPLS Generic Associated Channel,” June 2009.).

Figure 11 (PWE3 Protocol Stack Reference Model showing the G-ACh ) shows the reference model depicting how the control channel is associated with the pseudowire protocol stack. This is based on the reference model for VCCV shown in Figure 2 of [RFC5085] (Nadeau, T. and C. Pignataro, “Pseudowire Virtual Circuit Connectivity Verification (VCCV): A Control Channel for Pseudowires,” December 2007.).



       +-------------+                                +-------------+
       |  Payload    |           < FCAPS >            |  Payload    |
       +-------------+                                +-------------+
       |   Demux /   |         < ACH for PW >         |   Demux /   |
       |Discriminator|                                |Discriminator|
       +-------------+                                +-------------+
       |     PW      |             < PW >             |     PW      |
       +-------------+                                +-------------+
       |    PSN      |             < LSP >            |    PSN      |
       +-------------+                                +-------------+
       |  Physical   |                                |  Physical   |
       +-----+-------+                                +-----+-------+
             |                                              |
             |             ____     ___       ____          |
             |           _/    \___/   \    _/    \__       |
             |          /               \__/         \_     |
             |         /                               \    |
             +--------|      MPLS/MPLS-TP Network       |---+
                       \                               /
                        \   ___      ___     __      _/
                         \_/   \____/   \___/  \____/

 Figure 11: PWE3 Protocol Stack Reference Model showing the G-ACh  

PW associated channel messages are encapsulated using the PWE3 encapsulation, so that they are handled and processed in the same manner (or in some cases, an analogous manner) as the PW PDUs for which they provide a control channel.

Figure 12 (MPLS Protocol Stack Reference Model showing the LSP Associated Control Channel ) shows the reference model depicting how the control channel is associated with the LSP protocol stack.



       +-------------+                                +-------------+
       |  Payload    |           < FCAPS >            |   Payload   |
       +-------------+                                +-------------+
       |Discriminator|         < ACH on LSP >         |Discriminator|
       +-------------+                                +-------------+
       |Demultiplexer|         < GAL on LSP >         |Demultiplexer|
       +-------------+                                +-------------+
       |    PSN      |            < LSP >             |    PSN      |
       +-------------+                                +-------------+
       |  Physical   |                                |  Physical   |
       +-----+-------+                                +-----+-------+
             |                                              |
             |             ____     ___       ____          |
             |           _/    \___/   \    _/    \__       |
             |          /               \__/         \_     |
             |         /                               \    |
             +--------|      MPLS/MPLS-TP Network       |---+
                       \                               /
                        \   ___      ___     __      _/
                         \_/   \____/   \___/  \____/


 Figure 12: MPLS Protocol Stack Reference Model showing the LSP Associated Control Channel  



 TOC 

3.7.  Operations, Administration and Maintenance (OAM)

MPLS-TP must be able to operate in environments where IP is not used in the forwarding plane. Therefore, the default mechanism for OAM demultiplexing in MPLS-TP LSPs and PWs is the Generic Associated Channel (Section 3.6 (Generic Associated Channel (G-ACh))). Forwarding based on IP addresses for user or OAM packets is not required for MPLS-TP.

[RFC4379] (Kompella, K. and G. Swallow, “Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures,” February 2006.) and BFD for MPLS LSPs [I‑D.ietf‑bfd‑mpls] (Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow, “BFD For MPLS LSPs,” June 2008.) have defined alert mechanisms that enable an MPLS LSR to identify and process MPLS OAM packets when the OAM packets are encapsulated in an IP header. These alert mechanisms are based on TTL expiration and/or use an IP destination address in the range 127/8 for IPv4 and that same range embedded as IPv4 mapped IPv6 addresses for IPv6 [RFC4379] (Kompella, K. and G. Swallow, “Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures,” February 2006.). When the OAM packets are encapsulated in an IP header, these mechanisms are the default mechanisms for MPLS networks in general for identifying MPLS OAM packets. MPLS-TP must be able to operate in an environments where IP forwarding is not supported, and thus the GACH/GAL is the default mechanism to demultiplex OAM packets in MPLS-TP.

MPLS-TP supports a comprehensive set of OAM capabilities for packet transport applications, with equivalent capabilities to those provided in SONET/SDH.

MPLS-TP defines mechanisms to differentiate specific packets (e.g. OAM, APS, MCC or SCC) from those carrying user data packets on the same transport path (i.e. section, LSP or PW). These mechanisms are described in [RFC5586] (Bocci, M., Vigoureux, M., and S. Bryant, “MPLS Generic Associated Channel,” June 2009.).

MPLS-TP requires [I‑D.ietf‑mpls‑tp‑oam‑requirements] (Vigoureux, M. and D. Ward, “Requirements for OAM in MPLS Transport Networks,” March 2010.) that a set of OAM capabilities is available to perform fault management (e.g. fault detection and localisation) and performance monitoring (e.g. packet delay and loss measurement) of the LSP, PW or section. The framework for OAM in MPLS-TP is specified in [I‑D.ietf‑mpls‑tp‑oam‑framework] (Allan, D., Busi, I., Niven-Jenkins, B., Fulignoli, A., Hernandez-Valencia, E., Levrau, L., Mohan, D., Sestito, V., Sprecher, N., Helvoort, H., Vigoureux, M., Weingarten, Y., and R. Winter, “MPLS-TP OAM Framework,” April 2010.).

MPLS-TP OAM packets share the same fate as their corresponding data packets, and are identified through the Generic Associated Channel mechanism [RFC5586] (Bocci, M., Vigoureux, M., and S. Bryant, “MPLS Generic Associated Channel,” June 2009.). This uses a combination of an Associated Channel Header (ACH) and a Generic Alert Label (GAL) to create a control channel associated to an LSP, Section or PW.

OAM and monitoring in MPLS-TP is based on the concept of maintenance entities, as described in [I‑D.ietf‑mpls‑tp‑oam‑framework] (Allan, D., Busi, I., Niven-Jenkins, B., Fulignoli, A., Hernandez-Valencia, E., Levrau, L., Mohan, D., Sestito, V., Sprecher, N., Helvoort, H., Vigoureux, M., Weingarten, Y., and R. Winter, “MPLS-TP OAM Framework,” April 2010.). A Maintenance Entity can be viewed as the association of two Maintenance End Points (MEPs). A Maintenance Entity Group (MEG) is a collection of one or more MEs that belongs to the same transport path and that are maintained and monitored as a group. The MEPs that form an ME limit the OAM responsibilities of an OAM flow to within the domain of a transport path or segment, in the specific layer network that is being monitored and managed.

An ME may also include a set of Maintenance Intermediate Points (MIPs). Maintenance End Points (MEPs) are capable of sourcing and sinking OAM flows, while Maintenance Intermediate Points (MIPs) can only sink or respond to OAM flows from within a MEG, or originate notifications as a result of specific network conditions.

The following MPLS-TP MEs are specified in [I‑D.ietf‑mpls‑tp‑oam‑framework] (Allan, D., Busi, I., Niven-Jenkins, B., Fulignoli, A., Hernandez-Valencia, E., Levrau, L., Mohan, D., Sestito, V., Sprecher, N., Helvoort, H., Vigoureux, M., Weingarten, Y., and R. Winter, “MPLS-TP OAM Framework,” April 2010.):

A G-ACH packet may be directed to an individual MIP along the path of an LSP or MS-PW by setting the appropriate TTL in the label for the G-ACH packet, as per the traceroute mode of LSP Ping [RFC4379] (Kompella, K. and G. Swallow, “Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures,” February 2006.) and the vccv-trace mode of[I‑D.ietf‑pwe3‑segmented‑pw] (Martini, L., Nadeau, T., Metz, C., Bocci, M., Aissaoui, M., Balus, F., and M. Duckett, “Segmented Pseudowire,” April 2010.). Note that this works when the location of MIPs along the LSP or PW path is known by the MEP. There may be circumstances where this is not the case, e.g. following restoration using a facility bypass LSP. In these cases, tools to trace the path of the LSP may be used to determine the appropriate setting for the TTL to reach a specific MIP.

Within an LSR or PE, MEPs and MIPs can only be placed where MPLS layer processing is performed on a packet. The architecture mandates that this must occur at least once.

MEPs may only act as a sink of OAM packets when the label associated with the LSP or PW for that ME is popped. MIPs can only be placed where an exception to the normal forwarding operation occurs. A MEP may act as a source of OAM packets wherever a label is pushed or swapped. For example, on an MS-PW, a MEP may source OAM within an S-PE or a T-PE, but a MIP may only be associated with a S-PE and a sink MEP can only be associated with a T-PE.

The MPLS-TP OAM architecture supports a wide range of OAM functions to check continuity, to verify connectivity and to monitor the preformance of the path, to generate, filter and manage local and remote defect alarms. These functions are applicable to any layer defined within MPLS-TP, i.e. to MPLS-TP Sections, LSPs and PWs.

The MPLS-TP OAM tool-set must be able to operate without relying on a dynamic control plane or IP functionality in the datapath. In the case of an MPLS-TP deployment in a network in which IP functionality is available, all existing IP/MPLS OAM functions, e.g. LSP-Ping, BFD and VCCV, may be used.



 TOC 

3.8.  LSP Return Path

Management, control and OAM protocol functions may require response packets to be delivered from the receiver back to the originator of a message exchange. This section provides a summary of the return path options in MPLS-TP networks.

In this discussion we assume that A and B are terminal LSRs (i.e. LERs) for an MPLS-TP LSP and that Y is an intermediate LSR along the LSP. In the unidirectional case, A is taken to be the upstream and B the downstream LSR with respect to the LSP. We consider the following cases for the various types of LSPs:

  1. Packet transmission from B to A
  2. Packet transmission from Y to A
  3. Packet transmission from B to Y

Note that a return path may not always exist, and that packet transmission in one or more of the above cases may not be possible. In general the existence and nature of return paths for MPLS-TP LSPs is determined by operational provisioning.



 TOC 

3.8.1.  Return Path Types

There are two types of return path that may be used for the delivery of traffic from a downstream node D to an upstream node U either:

a.
D maintains an MPLS-TP LSP back to U which is specifically designated to carry return traffic for the original LSP, or
b.
D has some other unspecified means of directing traffic back to U.

The first option is referred to as an "in-band" return path, the second as an "out-of-band" return path.

There are various possibilities for "out-of-band" return paths. Such a path may, for example, be based on ordinary IP routing. In this case packets would be forwarded as usual to a destination IP address associated with U. In an MPLS-TP network that is also an IP/MPLS network, such a forwarding path may traverse the same physical links or logical transport paths used by MPLS-TP. An out-of-band return path may also be indirect, via a network management system; or it may be via one or more other MPLS-TP LSPs.



 TOC 

3.8.2.  Point-to-Point Unidirectional LSPs

Case 1
In this situation, either an in-band or out-of-band return path may be used to deliver traffic from B back to A.
In the in-band case there is in essence an associated bidirectional LSP between A and B, and the discussion for such LSPs below applies. It is therefore recommended for reasons of operational simplicity that point-to-point unidirectional LSPs be provisioned as associated bidirectional LSPs (which may also be co-routed) whenever return traffic from B to A is required. Note that the two directions of such an LSP may have differing bandwidth allocations and QoS characteristics.
Case 2
In this case only the out-of-band return path option is available. However, an additional out-of-band possibility is worthy of note here: if B is known to have a return path to A, then Y can arrange to deliver return traffic to A by first sending it to B along the original LSP. The mechanism by which B recognises the need for and performs this forwarding operation is protocol-specific.
Case 3
In this case only the out-of-band return path option is available. However, if B has a return path to A, then in a manner analogous to the previous case B can arrange to deliver return traffic to Y by first sending it to A along that return path. The mechanism by which A recognises the need for and performs this forwarding operation is protocol-specific.



 TOC 

3.8.3.  Point-to-Point Associated Bidirectional LSPs

For Case 1, B has a natural in-band return path to A, the use of which is typically preferred for return traffic, although out-of-band return paths are also applicable.

For Cases 2 and 3, the considerations are the same as those for point-to-point unidirectional LSPs.



 TOC 

3.8.4.  Point-to-Point Co-Routed Bidirectional LSPs

For all of Cases 1, 2, and 3, a natural in-band return path exists in the form of the LSP itself, and its use is typically preferred for return traffic. Out-of-band return paths, however, are also applicable.



 TOC 

3.9.  Control Plane

A distributed dynamic control plane may be used to enable dynamic service provisioning in an MPLS-TP network. Where the requirements specified in [RFC5654] (Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” September 2009.) can be met, the MPLS Transport Profile uses existing standard control plane protocols for LSPs and PWs.

Note that a dynamic control plane is not required in an MPLS-TP network. See Section 3.11 (Static Operation of LSPs and PWs) for further details on statically configured and provisioned MPLS-TP services.

Figure 13 (MPLS-TP Control Plane Architecture Context) illustrates the relationship between the MPLS-TP control plane, the forwarding plane, the management plane, and OAM for point-to-point MPLS-TP LSPs or PWs.



 +------------------------------------------------------------------+
 |                                                                  |
 |                Network Management System and/or                  |
 |                                                                  |
 |           Control Plane for Point to Point Connections           |
 |                                                                  |
 +------------------------------------------------------------------+
               |     |         |     |          |     |
  .............|.....|...  ....|.....|....  ....|.....|............
  :          +---+   |  :  : +---+   |   :  : +---+   |           :
  :          |OAM|   |  :  : |OAM|   |   :  : |OAM|   |           :
  :          +---+   |  :  : +---+   |   :  : +---+   |           :
  :            |     |  :  :   |     |   :  :   |     |           :
 \: +----+   +--------+ :  : +--------+  :  : +--------+   +----+ :/
--+-|Edge|<->|Forward-|<---->|Forward-|<----->|Forward-|<->|Edge|-+--
 /: +----+   |ing     | :  : |ing     |  :  : |ing     |   +----+ :\
  :          +--------+ :  : +--------+  :  : +--------+          :
  '''''''''''''''''''''''  '''''''''''''''  '''''''''''''''''''''''

Note:
   1) NMS may be centralised or distributed. Control plane is
      distributed.
   2) 'Edge' functions refers to those functions present at
      the edge of a PSN domain, e.g. NSP or classification.
   3) The control plane may be transported over the server
      layer, an LSP or a G-ACh.

 Figure 13: MPLS-TP Control Plane Architecture Context 

The MPLS-TP control plane is based on existing MPLS and PW control plane protocols. MPLS-TP uses Generalized MPLS (GMPLS) signalling ([RFC3945] (Mannie, E., “Generalized Multi-Protocol Label Switching (GMPLS) Architecture,” October 2004.), [RFC3471] (Berger, L., “Generalized Multi-Protocol Label Switching (GMPLS) Signaling Functional Description,” January 2003.), [RFC3473] (Berger, L., “Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) Extensions,” January 2003.)) for LSPs and Targetted LDP (T-LDP) [RFC4447] (Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G. Heron, “Pseudowire Setup and Maintenance Using the Label Distribution Protocol (LDP),” April 2006.) [I‑D.ietf‑pwe3‑segmented‑pw] (Martini, L., Nadeau, T., Metz, C., Bocci, M., Aissaoui, M., Balus, F., and M. Duckett, “Segmented Pseudowire,” April 2010.)[I‑D.ietf‑pwe3‑dynamic‑ms‑pw] (Martini, L., Bocci, M., Balus, F., Bitar, N., Shah, H., Aissaoui, M., Rusmisel, J., Serbest, Y., Malis, A., Metz, C., McDysan, D., Sugimoto, J., Duckett, M., Loomis, M., Doolan, P., Pan, P., Pate, P., Radoaca, V., Wada, Y., and Y. Seo, “Dynamic Placement of Multi Segment Pseudo Wires,” October 2009.) for pseudowires. When T-LDP is used as the PW control protocol, MPLS-TP requires that it is capable of being carried over an out of band signalling network or a signalling control channel [RFC5718] (Beller, D. and A. Farrel, “An In-Band Data Communication Network For the MPLS Transport Profile,” January 2010.). References to T-LDP in this document do not preclude the definition of alternative PW control protocols for use in MPLS-TP.

Note that if MPLS-TP is being used in a multi-layer network, a number of control protocol types and instances may be used. This is consistent with the MPLS architecture which permits each label in the label stack to be allocated and signalled by its own control protocol.

The distributed MPLS-TP control plane may provide the following functions:

In a multi-domain environment, the MPLS-TP control plane supports different types of interfaces at domain boundaries or within the domains. These include the User-Network Interface (UNI), Internal Network Node Interface (I-NNI), and External Network Node Interface (E-NNI). Note that different policies may be defined that control the information exchanged across these interface types.

The MPLS-TP control plane is capable of activating MPLS-TP OAM functions as described in the OAM section of this document Section 3.7 (Operations, Administration and Maintenance (OAM)), e.g. for fault detection and localisation in the event of a failure in order to efficiently restore failed transport paths.

The MPLS-TP control plane supports all MPLS-TP data plane connectivity patterns that are needed for establishing transport paths, including protected paths as described in Section 3.12 (Survivability). Examples of the MPLS-TP data plane connectivity patterns are LSPs utilising the fast reroute backup methods as defined in [RFC4090] (Pan, P., Swallow, G., and A. Atlas, “Fast Reroute Extensions to RSVP-TE for LSP Tunnels,” May 2005.) and ingress-to-egress 1+1 or 1:1 protected LSPs.

The MPLS-TP control plane provides functions to ensure its own survivability and to enable it to recover gracefully from failures and degradations. These include graceful restart and hot redundant configurations. Depending on how the control plane is transported, varying degrees of decoupling between the control plane and data plane may be achieved.



 TOC 

3.10.  Inter-domain Connectivity

A number of methods exist to support inter-domain operation of MPLS-TP, for example:

An important consideration in selecting an inter-domain connectivity mechanism is the degree of layer network isolation and types of OAM required by the operator. The selection of which technique to use in a particular deployment scenario is outside the scope of this document.



 TOC 

3.11.  Static Operation of LSPs and PWs

A PW or LSP may be statically configured without the support of a dynamic control plane. This may be either by direct configuration of the PEs/LSRs, or via a network management system. Static operation is independent for a specific PW or LSP instance. Thus it should be possible for a PW to be statically configured, while the LSP supporting it is set up by a dynamic control plane. When static configuration mechanisms are used, care must be taken to ensure that loops are not created.



 TOC 

3.12.  Survivability

Survivability requirements for MPLS-TP are specified in [I‑D.ietf‑mpls‑tp‑survive‑fwk] (Sprecher, N. and A. Farrel, “Multiprotocol Label Switching Transport Profile Survivability Framework,” April 2010.).

A wide variety of resiliency schemes have been developed to meet the various network and service survivability objectives. For example, as part of the MPLS/PW paradigms, MPLS provides methods for local repair using back-up LSP tunnels ([RFC4090] (Pan, P., Swallow, G., and A. Atlas, “Fast Reroute Extensions to RSVP-TE for LSP Tunnels,” May 2005.)), while pseudowire redundancy [I‑D.ietf‑pwe3‑redundancy] (Muley, P. and V. Place, “Pseudowire (PW) Redundancy,” October 2009.) supports scenarios where the protection for the PW cannot be fully provided by the underlying LSP (i.e. where the backup PW terminates on a different target PE node than the working PW in dual homing scenarios, or where protection of the S-PE is required). Additionally, GMPLS provides a well known set of control plane driven protection and restoration mechanisms [RFC4872] (Lang, J., Rekhter, Y., and D. Papadimitriou, “RSVP-TE Extensions in Support of End-to-End Generalized Multi-Protocol Label Switching (GMPLS) Recovery,” May 2007.). MPLS-TP provides additional protection mechanisms that are optimised for both linear topologies and ring topologies, and that operate in the absence of a dynamic control plane. These are specified in [I‑D.ietf‑mpls‑tp‑survive‑fwk] (Sprecher, N. and A. Farrel, “Multiprotocol Label Switching Transport Profile Survivability Framework,” April 2010.).

Different protection schemes apply to different deployment topologies and operational considerations. Such protection schemes may provide different levels of resiliency, for example:

The applicability of any given scheme to meet specific requirements is outside the current scope of this document.

The characteristics of MPLS-TP resiliency mechanisms are as follows:



 TOC 

3.13.  Path Segment Tunnels

In order to monitor, protect and manage a portion of an LSP, a new architectural element is defined. This the Path Segment Tunnel (PST). A PST is an LSP defined and used for the purposes of OAM monitoring, protection or management of LSP segment or concatenated LSP segments, and based on MPLS hierarchical nested LSP defined in [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.).

A PST is defined between the edges of the portion of the LSP that needs to be monitored, protected or managed. Maintenance messages can be initiated at the edge of the PST and sent to the peer edge of the PST or to an intermediate point along the PST setting the TTL value at the PST level accordingly.

For example in Figure 14 (PSTs in inter-carrier network), three PSTs are configured to allow monitoring, protection and management of the LSP concatenated segments. One PST is defined between PE1 and PE2, the second between PE2 and PE3 and a third PST is set up between PE3 and PE4. Each of these three PSTs may be monitored, protected, or managed independently.



========================== End to End LSP =============================

   |<--------- Carrier 1 --------->|       |<----- Carrier 2 ----->|

---| PE1 |---| P |---| P |---| PE2 |-------| PE3 |---| P |---| PE4 |---

   |============= PST =============|==PST==|========= PST =========|
              (Carrier 1)                          (Carrier 2)

 Figure 14: PSTs in inter-carrier network 

The end-to-end traffic of the LSP, including data-traffic and control traffic (OAM, Protection Switching Control, management and signalling messages) is tunneled within the PST by means of label stacking as defined in [RFC3031] (Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” January 2001.).

The mapping between an LSP and a PST can be 1:1, in which it is similar to the ITU-T Tandem Connection element [G.805] (, “ITU-T Recommendation G.805 (11/95), "Generic Functional Architecture of Transport Networks",” November 1995.). The mapping can also be 1:N to allow aggregated monitoring, protection and management of a set of LSP segments or concatenated LSP segments. Figure 15 (PST for a Set of Concatenated LSP Segments) shows a PST which is used to aggregate a set of concatenated LSP segments for the LSP from PEx to PEt and the LSP from PEa to PEd. Note that such a construct is useful, for example, when the LSPs traverse a common portion of the network and they have the same Traffic Class.



|PEx|--|PEy|-+                                      +-|PEz|--|PEt|
             |                                      |
             |  |<---------- Carrier 1 --------->|  |
             |  +-----+   +---+   +---+    +-----+  |
             +--|     |---|   |---|   |----|     |--+
                | PE1 |   | P |   | P |    | PE2 |
             +--|     |---|   |---|   |----|     |--+
             |  +-----+   +---+   + P +    +-----+  |
             |  |============= PST ==============|  |
|PEa|--|PEb|-+            (Carrier 1)               +-|PEc|--|PEd|

 Figure 15: PST for a Set of Concatenated LSP Segments 



 TOC 

3.13.1.  Provisioning of PST

PSTs can be either provisioned statically or using control plane signalling procedures. The make-before-break procedures which are supported by MPLS allow the creation of a PST on existing LSPs in-service without traffic disruption. A PST can be defined corresponding to one or more end-to-end tunneled LSPs. New end-to-end LSPs which are tunneled within the PST can be setup. Traffic of the existing LSPs is switched over to the new end-to-end tunneled LSPs. The old end-to-end LSPs can be tore down.



 TOC 

3.14.  Pseudowire Segment Tunnels

Pseudowire segment tunnels are for further study.



 TOC 

3.15.  Network Management

The network management architecture and requirements for MPLS-TP are specified in [I‑D.ietf‑mpls‑tp‑nm‑framework] (Mansfield, S., Gray, E., and H. Lam, “MPLS-TP Network Management Framework,” February 2010.) and [I‑D.ietf‑mpls‑tp‑nm‑req] (Mansfield, S. and K. Lam, “MPLS TP Network Management Requirements,” October 2009.). These derive from the generic specifications described in ITU-T G.7710/Y.1701 [G.7710] (, “ITU-T Recommendation G.7710/Y.1701 (07/07), "Common equipment management function requirements",” 2005.) for transport technologies. It also incorporates the OAM requirements for MPLS Networks [RFC4377] (Nadeau, T., Morrow, M., Swallow, G., Allan, D., and S. Matsushima, “Operations and Management (OAM) Requirements for Multi-Protocol Label Switched (MPLS) Networks,” February 2006.) and MPLS-TP Networks [I‑D.ietf‑mpls‑tp‑oam‑requirements] (Vigoureux, M. and D. Ward, “Requirements for OAM in MPLS Transport Networks,” March 2010.) and expands on those requirements to cover the modifications necessary for fault, configuration, performance, and security in a transport network.

The Equipment Management Function (EMF) of an MPLS-TP Network Element (NE) (i.e. LSR, LER, PE, S-PE or T-PE) provides the means through which a management system manages the NE. The Management Communication Channel (MCC), realised by the G-ACh, provides a logical operations channel between NEs for transferring Management information. For the management interface from a management system to an MPLS-TP NE, there is no restriction on which management protocol is used. The MCC is used to provision and manage an end-to-end connection across a network where some segments are created/managed by, for example, Netconf [RFC4741] (Enns, R., “NETCONF Configuration Protocol,” December 2006.) or SNMP [RFC3411] (Harrington, D., Presuhn, R., and B. Wijnen, “An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks,” December 2002.) and other segments by XML or CORBA interfaces. Maintenance operations are run on a connection (LSP or PW) in a manner that is independent of the provisioning mechanism. An MPLS-TP NE is not required to offer more than one standard management interface. In MPLS-TP, the EMF must be capable of statically provisioning LSPs for an LSR or LER, and PWs for a PE, as well as any associated MEPs and MIPs, as per Section 3.11 (Static Operation of LSPs and PWs).

Fault Management (FM) functions within the EMF of an MPLS-TP NE enable the supervision, detection, validation, isolation, correction, and alarm handling of abnormal conditions in the MPLS-TP network and its environment. FM must provide for the supervision of transmission (such as continuity, connectivity, etc.), software processing, hardware, and environment. Alarm handling includes alarm severity assignment, alarm suppression/aggregation/correlation, alarm reporting control, and alarm reporting.

Configuration Management (CM) provides functions to control, identify, collect data from, and provide data to MPLS-TP NEs. In addition to general configuration for hardware, software protection switching, alarm reporting control, and date/time setting, the EMF of the MPLS-TP NE also supports the configuration of maintenance entity identifiers (such as MEP ID and MIP ID). The EMF also supports the configuration of OAM parameters as a part of connectivity management to meet specific operational requirements. These may specify whether the operational mode is one-time on-demand or is periodic at a specified frequency.

The Performance Management (PM) functions within the EMF of an MPLS-TP NE support the evaluation and reporting of the behaviour of the NEs and the network. One particular requirement for PM is to provide coherent and consistent interpretation of the network behaviour in a hybrid network that uses multiple transport technologies. Packet loss measurement and delay measurements may be collected and used to detect performance degradation. This is reported via fault management to enable corrective actions to be taken (e.g. protection switching), and via performance monitoring for Service Level Agreement (SLA) verification and billing. Collection mechanisms for performance data should be capable of operating on-demand or pro-actively.



 TOC 

4.  Security Considerations

The introduction of MPLS-TP into transport networks means that the security considerations applicable to both MPLS and PWE3 apply to those transport networks. Furthermore, when general MPLS networks that utilise functionality outside of the strict MPLS Transport Profile are used to support packet transport services, the security considerations of that additional functionality also apply.

For pseudowires, the security considerations of [RFC3985] (Bryant, S. and P. Pate, “Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture,” March 2005.) and [RFC5659] (Bocci, M. and S. Bryant, “An Architecture for Multi-Segment Pseudowire Emulation Edge-to-Edge,” October 2009.) apply.

Packets that arrive on an interface with a given label value should not be forwarded unless that label value is assigned to an LSP or PW to a peer LSR or PE that is reachable via that interface.

Each MPLS-TP solution must specify the additional security considerations that apply. This is discussed further in [I‑D.fang‑mpls‑tp‑security‑framework] (Fang, L. and B. Niven-Jenkins, “Security Framework for MPLS-TP,” March 2010.).



 TOC 

5.  IANA Considerations

IANA considerations resulting from specific elements of MPLS-TP functionality will be detailed in the documents specifying that functionality.

This document introduces no additional IANA considerations in itself.



 TOC 

6.  Acknowledgements

The editors wish to thank the following for their contribution to this document:



 TOC 

7.  Open Issues

This section contains a list of issues that must be resolved before last call.



 TOC 

8.  References



 TOC 

8.1. Normative References

[G.7710] “ITU-T Recommendation G.7710/Y.1701 (07/07), "Common equipment management function requirements",” 2005.
[G.805] “ITU-T Recommendation G.805 (11/95), "Generic Functional Architecture of Transport Networks",” November 1995.
[RFC3031] Rosen, E., Viswanathan, A., and R. Callon, “Multiprotocol Label Switching Architecture,” RFC 3031, January 2001 (TXT).
[RFC3032] Rosen, E., Tappan, D., Fedorkow, G., Rekhter, Y., Farinacci, D., Li, T., and A. Conta, “MPLS Label Stack Encoding,” RFC 3032, January 2001 (TXT).
[RFC3270] Le Faucheur, F., Wu, L., Davie, B., Davari, S., Vaananen, P., Krishnan, R., Cheval, P., and J. Heinanen, “Multi-Protocol Label Switching (MPLS) Support of Differentiated Services,” RFC 3270, May 2002 (TXT).
[RFC3471] Berger, L., “Generalized Multi-Protocol Label Switching (GMPLS) Signaling Functional Description,” RFC 3471, January 2003 (TXT).
[RFC3473] Berger, L., “Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) Extensions,” RFC 3473, January 2003 (TXT).
[RFC3985] Bryant, S. and P. Pate, “Pseudo Wire Emulation Edge-to-Edge (PWE3) Architecture,” RFC 3985, March 2005 (TXT).
[RFC4090] Pan, P., Swallow, G., and A. Atlas, “Fast Reroute Extensions to RSVP-TE for LSP Tunnels,” RFC 4090, May 2005 (TXT).
[RFC4385] Bryant, S., Swallow, G., Martini, L., and D. McPherson, “Pseudowire Emulation Edge-to-Edge (PWE3) Control Word for Use over an MPLS PSN,” RFC 4385, February 2006 (TXT).
[RFC4447] Martini, L., Rosen, E., El-Aawar, N., Smith, T., and G. Heron, “Pseudowire Setup and Maintenance Using the Label Distribution Protocol (LDP),” RFC 4447, April 2006 (TXT).
[RFC4872] Lang, J., Rekhter, Y., and D. Papadimitriou, “RSVP-TE Extensions in Support of End-to-End Generalized Multi-Protocol Label Switching (GMPLS) Recovery,” RFC 4872, May 2007 (TXT).
[RFC5085] Nadeau, T. and C. Pignataro, “Pseudowire Virtual Circuit Connectivity Verification (VCCV): A Control Channel for Pseudowires,” RFC 5085, December 2007 (TXT).
[RFC5462] Andersson, L. and R. Asati, “Multiprotocol Label Switching (MPLS) Label Stack Entry: "EXP" Field Renamed to "Traffic Class" Field,” RFC 5462, February 2009 (TXT).
[RFC5586] Bocci, M., Vigoureux, M., and S. Bryant, “MPLS Generic Associated Channel,” RFC 5586, June 2009 (TXT).


 TOC 

8.2. Informative References

[I-D.fang-mpls-tp-security-framework] Fang, L. and B. Niven-Jenkins, “Security Framework for MPLS-TP,” draft-fang-mpls-tp-security-framework-01 (work in progress), March 2010 (TXT).
[I-D.ietf-bfd-mpls] Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow, “BFD For MPLS LSPs,” draft-ietf-bfd-mpls-07 (work in progress), June 2008 (TXT).
[I-D.ietf-l2vpn-vpms-frmwk-requirements] Kamite, Y., JOUNAY, F., Niven-Jenkins, B., Brungard, D., and L. Jin, “Framework and Requirements for Virtual Private Multicast Service (VPMS),” draft-ietf-l2vpn-vpms-frmwk-requirements-02 (work in progress), October 2009 (TXT).
[I-D.ietf-mpls-tp-identifiers] Bocci, M. and G. Swallow, “MPLS-TP Identifiers,” draft-ietf-mpls-tp-identifiers-01 (work in progress), March 2010 (TXT).
[I-D.ietf-mpls-tp-nm-framework] Mansfield, S., Gray, E., and H. Lam, “MPLS-TP Network Management Framework,” draft-ietf-mpls-tp-nm-framework-05 (work in progress), February 2010 (TXT).
[I-D.ietf-mpls-tp-nm-req] Mansfield, S. and K. Lam, “MPLS TP Network Management Requirements,” draft-ietf-mpls-tp-nm-req-06 (work in progress), October 2009 (TXT).
[I-D.ietf-mpls-tp-oam-framework] Allan, D., Busi, I., Niven-Jenkins, B., Fulignoli, A., Hernandez-Valencia, E., Levrau, L., Mohan, D., Sestito, V., Sprecher, N., Helvoort, H., Vigoureux, M., Weingarten, Y., and R. Winter, “MPLS-TP OAM Framework,” draft-ietf-mpls-tp-oam-framework-06 (work in progress), April 2010 (TXT).
[I-D.ietf-mpls-tp-oam-requirements] Vigoureux, M. and D. Ward, “Requirements for OAM in MPLS Transport Networks,” draft-ietf-mpls-tp-oam-requirements-06 (work in progress), March 2010 (TXT).
[I-D.ietf-mpls-tp-survive-fwk] Sprecher, N. and A. Farrel, “Multiprotocol Label Switching Transport Profile Survivability Framework,” draft-ietf-mpls-tp-survive-fwk-05 (work in progress), April 2010 (TXT).
[I-D.ietf-pwe3-dynamic-ms-pw] Martini, L., Bocci, M., Balus, F., Bitar, N., Shah, H., Aissaoui, M., Rusmisel, J., Serbest, Y., Malis, A., Metz, C., McDysan, D., Sugimoto, J., Duckett, M., Loomis, M., Doolan, P., Pan, P., Pate, P., Radoaca, V., Wada, Y., and Y. Seo, “Dynamic Placement of Multi Segment Pseudo Wires,” draft-ietf-pwe3-dynamic-ms-pw-10 (work in progress), October 2009 (TXT).
[I-D.ietf-pwe3-redundancy] Muley, P. and V. Place, “Pseudowire (PW) Redundancy,” draft-ietf-pwe3-redundancy-02 (work in progress), October 2009 (TXT).
[I-D.ietf-pwe3-segmented-pw] Martini, L., Nadeau, T., Metz, C., Bocci, M., Aissaoui, M., Balus, F., and M. Duckett, “Segmented Pseudowire,” draft-ietf-pwe3-segmented-pw-14 (work in progress), April 2010 (TXT).
[RFC3209] Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, “RSVP-TE: Extensions to RSVP for LSP Tunnels,” RFC 3209, December 2001 (TXT).
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, “An Architecture for Describing Simple Network Management Protocol (SNMP) Management Frameworks,” STD 62, RFC 3411, December 2002 (TXT).
[RFC3443] Agarwal, P. and B. Akyol, “Time To Live (TTL) Processing in Multi-Protocol Label Switching (MPLS) Networks,” RFC 3443, January 2003 (TXT).
[RFC3945] Mannie, E., “Generalized Multi-Protocol Label Switching (GMPLS) Architecture,” RFC 3945, October 2004 (TXT).
[RFC4216] Zhang, R. and J. Vasseur, “MPLS Inter-Autonomous System (AS) Traffic Engineering (TE) Requirements,” RFC 4216, November 2005 (TXT).
[RFC4364] Rosen, E. and Y. Rekhter, “BGP/MPLS IP Virtual Private Networks (VPNs),” RFC 4364, February 2006 (TXT).
[RFC4377] Nadeau, T., Morrow, M., Swallow, G., Allan, D., and S. Matsushima, “Operations and Management (OAM) Requirements for Multi-Protocol Label Switched (MPLS) Networks,” RFC 4377, February 2006 (TXT).
[RFC4379] Kompella, K. and G. Swallow, “Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures,” RFC 4379, February 2006 (TXT).
[RFC4664] Andersson, L. and E. Rosen, “Framework for Layer 2 Virtual Private Networks (L2VPNs),” RFC 4664, September 2006 (TXT).
[RFC4741] Enns, R., “NETCONF Configuration Protocol,” RFC 4741, December 2006 (TXT).
[RFC5150] Ayyangar, A., Kompella, K., Vasseur, JP., and A. Farrel, “Label Switched Path Stitching with Generalized Multiprotocol Label Switching Traffic Engineering (GMPLS TE),” RFC 5150, February 2008 (TXT).
[RFC5254] Bitar, N., Bocci, M., and L. Martini, “Requirements for Multi-Segment Pseudowire Emulation Edge-to-Edge (PWE3),” RFC 5254, October 2008 (TXT).
[RFC5309] Shen, N. and A. Zinin, “Point-to-Point Operation over LAN in Link State Routing Protocols,” RFC 5309, October 2008 (TXT).
[RFC5331] Aggarwal, R., Rekhter, Y., and E. Rosen, “MPLS Upstream Label Assignment and Context-Specific Label Space,” RFC 5331, August 2008 (TXT).
[RFC5654] Niven-Jenkins, B., Brungard, D., Betts, M., Sprecher, N., and S. Ueno, “Requirements of an MPLS Transport Profile,” RFC 5654, September 2009 (TXT).
[RFC5659] Bocci, M. and S. Bryant, “An Architecture for Multi-Segment Pseudowire Emulation Edge-to-Edge,” RFC 5659, October 2009 (TXT).
[RFC5718] Beller, D. and A. Farrel, “An In-Band Data Communication Network For the MPLS Transport Profile,” RFC 5718, January 2010 (TXT).


 TOC 

Authors' Addresses

  Matthew Bocci (editor)
  Alcatel-Lucent
  Voyager Place, Shoppenhangers Road
  Maidenhead, Berks SL6 2PJ
  United Kingdom
Phone: 
EMail:  matthew.bocci@alcatel-lucent.com
  
  Stewart Bryant (editor)
  Cisco Systems
  250 Longwater Ave
  Reading RG2 6GB
  United Kingdom
Phone: 
EMail:  stbryant@cisco.com
  
  Dan Frost
  Cisco Systems
 
Phone: 
Fax: 
EMail:  danfrost@cisco.com
URI: 
  
  Lieven Levrau
  Alcatel-Lucent
  7-9, Avenue Morane Sulnier
  Velizy 78141
  France
Phone: 
EMail:  lieven.levrau@alcatel-lucent.com
  
  Lou Berger
  LabN
 
Phone:  +1-301-468-9228
Fax: 
EMail:  lberger@labn.net
URI: