Network Working Group Kireeti Kompella Internet Draft Juniper Networks Expiration Date: August 2002 Yakov Rekhter Juniper Networks Signalling Unnumbered Links in RSVP-TE draft-ietf-mpls-rsvp-unnum-04.txt 1. Status of this Memo This document is an Internet-Draft and is in full conformance with all provisions of Section 10 of RFC2026. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as ``work in progress.'' The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. 2. Abstract Current signalling used by MPLS TE doesn't provide support for unnumbered links. This document defines procedures and extensions to RSVP-TE, one of the MPLS TE signalling protocols, that are needed in order to support unnumbered links. draft-ietf-mpls-rsvp-unnum-04.txt [Page 1] Internet Draft draft-ietf-mpls-rsvp-unnum-04.txt February 2002 3. Overview Supporting MPLS TE over unnumbered links (i.e., links that do not have IP addresses) involves two components: (a) the ability to carry (TE) information about unnumbered links in IGP TE extensions (ISIS or OSPF), and (b) the ability to specify unnumbered links in MPLS TE signalling. The former is covered in [GMPLS-ISIS, GMPLS-OSPF]. The focus of this document is on the latter. Current signalling used by MPLS TE doesn't provide support for unnumbered links because the current signalling doesn't provide a way to indicate an unnumbered link in its Explicit Route and Record Route Objects. This document proposes simple procedures and extensions that allow RSVP-TE signalling [GMPLS-RSVP] to be used with unnumbered links. 4. Link Identifiers An unnumbered link has to be a point-to-point link. An LSR at each end of an unnumbered link assigns an identifier to that link. This identifier is a non-zero 32-bit number that is unique within the scope of the LSR that assigns it. The IS-IS and/or OSPF and RSVP modules on an LSR must agree on the identifiers. There is no a priori relationship between the identifiers assigned to a link by the LSRs at each end of that link. LSRs at the two end points of an unnumbered link exchange with each other the identifiers they assign to the link. Exchanging the identifiers may be accomplished by configuration, by means of a protocol such as LMP ([LMP]), by means of RSVP/CR-LDP (especially in the case where a link is a Forwarding Adjacency, see below), or by means of IS-IS or OSPF extensions ([ISIS-GMPLS], [OSPF-GMPLS]). Consider an (unnumbered) link between LSRs A and B. LSR A chooses an idenfitier for that link. So is LSR B. From A's perspective we refer to the identifier that A assigned to the link as the "link local identifier" (or just "local identifier"), and to the identifier that B assigned to the link as the "link remote identifier" (or just "remote identifier"). Likewise, from B's perspective the identifier that B assigned to the link is the local identifier, and the identifier that A assigned to the link is the remote identifier. This section is equally applicable to the case of unnumbered component links (see [LINK-BUNDLE]). draft-ietf-mpls-rsvp-unnum-04.txt [Page 2] Internet Draft draft-ietf-mpls-rsvp-unnum-04.txt February 2002 5. Unnumbered Forwarding Adjacencies If an LSR that originates an LSP advertises this LSP as an unnumbered Forwarding Adjacency in IS-IS or OSPF (see [LSP-HIER]), or the LSR uses the Forwarding Adjacency formed by this LSP as an unnumbered component link of a bundled link (see [LINK-BUNDLE]), the LSR MUST allocate an identifier to that Forwarding Adjacency (just like for any other unnumbered link). Moreover, the Path message used for establishing the LSP that forms the Forwarding Adjacency MUST contain the LSP_TUNNEL_INTERFACE_ID object (described below), with the LSR's Router ID set to the head end's Router ID, and the Interface ID set to the identifier that the LSR allocated to the Forwarding Adjacency. If the Path message contains the LSP_TUNNEL_INTERFACE_ID object, then the tail-end LSR MUST allocate an identifier to that Forwarding Adjacency (just like for any other unnumbered link). Furthermore, the Resv message for the LSP MUST contain an LSP_TUNNEL_INTERFACE_ID object, with the LSR's Router ID set to the tail-end's Router ID, and the Interface ID set to the identifier allocated by the tail-end LSR. For the purpose of processing the ERO and the IF_ID RSVP_HOP objects, an unnumbered Forwarding Adjacency is treated as an unnumbered (TE) link or an unnumbered component link as follows. The LSR that originates the Adjacency sets the link local identifier for that link to the value that the LSR allocates to that Forwarding Adjacency, and the link remote identifier to the value carried in the Interface ID field of the Reverse Interface ID object. The LSR that is a tail-end of that Forwarding Adjacency sets the link local identifier for that link to the value that the LSR allocates to that Forwarding Adjacency, and the link remote identifier to the value carried in the Interface ID field of the Forward Interface ID object. 5.1. LSP_TUNNEL_INTERFACE_ID Object The LSP_TUNNEL_INTERFACE_ID object has a class number of type 11bbbbbb (to be assigned by IANA), C-Type of 1 and length of 12. The format is given below. This object can optionally appear in either a Path message or a Resv message. In the former case, we call it the "Forward Interface ID" for that LSP; in the latter case, we call it the "Reverse Interface ID" for the LSP. draft-ietf-mpls-rsvp-unnum-04.txt [Page 3] Internet Draft draft-ietf-mpls-rsvp-unnum-04.txt February 2002 Figure 1: LSP_TUNNEL_INTERFACE_ID Object 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LSR's Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Interface ID (32 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ 6. Signalling Unnumbered Links in EROs A new subobject of the Explicit Route Object (ERO) is used to specify unnumbered links. This subobject has the following format: Figure 2: Unnumbered Interface ID Subobject 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |L| Type | Length | Reserved (MUST be zero) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Interface ID (32 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Type is 4 (Unnumbered Interface ID). The Length is 12. The Interface ID is the identifier assigned to the link by the LSR specified by the router ID. 6.1. Processing the IF_ID RSVP_HOP object When an LSR receives a Path message containing the IF_ID RSVP_HOP object (see [GMPLS-RSVP]) with the IF_INDEX TLV, the LSR processes this TLV as follows. The LSR must have information about the identifiers assigned by its neighbors to the unnumbered links between the neighbors and the LSR. The LSR uses this information to find a link with tuple matching the tuple carried in the IF_INDEX TLV. If the matching tuple is found, the match identifies the link for which the LSR has to perform label allocation. Otherwise, the LSR SHOULD return an error. draft-ietf-mpls-rsvp-unnum-04.txt [Page 4] Internet Draft draft-ietf-mpls-rsvp-unnum-04.txt February 2002 6.2. Processing the ERO object The Unnumbered Interface ID subobject is defined to be a part of a particular abstract node if that node has the Router ID that is equal to the Router ID field in the subobject, and if the node has an (unnumbered) link or an (unnumbered) Forwarding Adjacency whose local identifier (from that node's point of view) is equal to the value carried in the Interface ID field of the subobject. With this in mind, the ERO processing in the presence of the Unnumbered Interface ID subobject follows the rules specified in section 4.3.4.1 of [RSVP-TE]. As part of the ERO processing, or to be more precise, as part of the next hop selection, if the outgoing link is unnumbered, the Path message that the node sends to the next hop MUST include the IF_ID RSVP_HOP object, with the IP address field of that object set to the Router ID of the node, and the Interface ID field of that object set to the identifier assigned to the link by the node. 7. Record Route Object A new subobject of the Record Route Object (RRO) is used to record that the LSP path traversed an unnumbered link. This subobject has the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Flags | Reserved (MBZ)| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Interface ID (32 bits) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The Type is 4 (Unnumbered Interface ID); the Length is 12. Flags are defined below. 0x01 Local protection available Indicates that the link downstream of this node is protected via a local repair mechanism. This flag can only be set if the Local protection flag was set in the SESSION_ATTRIBUITE object of the cooresponding Path message. 0x02 Local protection in use draft-ietf-mpls-rsvp-unnum-04.txt [Page 5] Internet Draft draft-ietf-mpls-rsvp-unnum-04.txt February 2002 Indicates that a local repair mechanism is in use to maintain this tunnel (usually in the face a an outage of the link it was previously routed over). 7.1. Handling RRO If at an intermediate node (or at the head-end), the ERO subobject that was used to determine the next hop is of type Unnumbered Interface ID, and a RRO object was received in the Path message (or is desired in the original Path message), an RRO subobject of type Unnumbered Interface ID MUST be appended to the received RRO when sending a Path message downstream. If the ERO subobject that was used to determine the next hop is of any other type, the handling procedures of [RSVP-TE] apply. Also, if Label Recording is desired, the procedures of [RSVP-TE] apply. 8. Security Considerations This document raises no new security concerns for RSVP. 9. IANA Considerations The responsible Internet authority (presently called the IANA) assigns values to RSVP protocol parameters. The current document defines a new subobject for the EXPLICIT_ROUTE object and for the ROUTE_RECORD object. The rules for the assignment of subobject numbers have been defined in [RSVP-TE], using the terminology of BCP 26 "Guidelines for Writing an IANA Considerations Section in RFCs". Those rules apply to the assignment of subobject numbers for the new subobject of the EXPLICIT_ROUTE and ROUTE_RECORD objects. Furthermore, the same Internet authority needs to assign a class number to the LSP_TUNNEL_INTERFACE_ID object. This must be of the form 11bbbbbb (i.e., this is an 8-bit number whose two most significant bits are 1). draft-ietf-mpls-rsvp-unnum-04.txt [Page 6] Internet Draft draft-ietf-mpls-rsvp-unnum-04.txt February 2002 10. Acknowledgments Thanks to Lou Berger and Markus Jork for pointing out that the RRO should be extended in like fashion to the ERO. Thanks also to Rahul Aggarwal and Alan Kullberg for their comments on the text. Finally, thanks to Bora Akyol and Vach Kompella. 11. References [LINK-BUNDLE] Kompella, K., Rekhter, Y., and Berger, L., "Link Bundling in MPLS Traffic Engineering", draft-kompella-mpls- bundle-05.txt (work in progress) [LSP-HIER] Kompella, K., and Rekhter, Y., "LSP Hierarchy with MPLS TE", draft-ietf-mpls-lsp-hierarchy-02.txt (work in progress) [RSVP-TE] Awduche, D., Berger, L., Gan, D. H., Li, T., Srinivasan, V., and Swallow, G., "RSVP-TE: Extensions to RSVP for LSP Tunnels", draft-ietf-mpls-rsvp-lsp-tunnel-08.txt (work in progress) [GMPLS-ISIS] Kompella, K., Rekhter, Y., Banerjee, A. et al, "IS-IS Extensions in Support of Generalized MPLS", draft-ietf-isis-gmpls- extensions-02.txt (work in progress) [GMPLS-OSPF] Kompella, K., Rekhter, Y., Banerjee, A. et al, "OSPF Extensions in Support of Generalized MPLS", draft-ietf-ccamp-ospf- gmpls-extensions-00.txt (work in progress) [GMPLS-RSVP] Ashwood, P., et al., "Generalized MPLS Signalling RSVP- TE Extensions", draft-ietf-mpls-generalized-rsvp-te-04.txt 12. Author Information draft-ietf-mpls-rsvp-unnum-04.txt [Page 7] Internet Draft draft-ietf-mpls-rsvp-unnum-04.txt February 2002 Kireeti Kompella Juniper Networks, Inc. 1194 N. Mathilda Ave. Sunnyvale, CA 94089 e-mail: kireeti@juniper.net Yakov Rekhter Juniper Networks, Inc. 1194 N. Mathilda Ave. Sunnyvale, CA 94089 e-mail: yakov@juniper.net draft-ietf-mpls-rsvp-unnum-04.txt [Page 8]