Internet Engineering Task Force N. Akiya Internet-Draft Big Switch Networks Updates: 7110 (if approved) G. Swallow Intended status: Standards Track C. Pignataro Expires: April 10, 2016 Cisco Systems L. Andersson M. Chen Huawei October 8, 2015 Label Switched Path (LSP) Ping/Traceroute Reply Mode Simplification draft-ietf-mpls-lsp-ping-reply-mode-simple-05 Abstract The Multiprotocol Label Switching (MPLS) Label Switched Path (LSP) Ping and Traceroute use the Reply Mode field to signal the method to be used in the MPLS echo reply. This document updates the procedures for the "Reply via Specified Path" Reply Mode, the value of this Reply Mode is 5. The update creates a simple way to indicate that the Reverse LSP should be used as return path. This document also adds an optional TLV which can carry ordered list of Reply Mode values. This document updates RFC7110. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." Akiya, et al. Expires April 10, 2016 [Page 1] Internet-Draft LSP Ping Reply Mode Simplification October 2015 This Internet-Draft will expire on April 10, 2016. Copyright Notice Copyright (c) 2015 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Problem Statements . . . . . . . . . . . . . . . . . . . . . 3 3. Solution . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1. Reply via Specified Path Update . . . . . . . . . . . . . 5 3.2. Reply Mode Order TLV . . . . . . . . . . . . . . . . . . 6 4. Relations to Other LSP Ping/Trace Features . . . . . . . . . 8 4.1. Backwards Compatibility with Reply via Specified Path Reply Mode . . . . . . . . . . . . . . . . . . . . . . . 8 4.2. Reply Path TLV . . . . . . . . . . . . . . . . . . . . . 8 4.2.1. Example 1: Reply Mode Order TLV Usage with Reply Path TLV . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.2.2. Example 2: Reply Mode Order TLV Usage with Reply Path TLV . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.3. Proxy LSP Ping . . . . . . . . . . . . . . . . . . . . . 10 4.3.1. Proxy LSR Sending an MPLS Echo Request . . . . . . . 10 4.3.2. Proxy LSR Sending an MPLS Proxy Ping Reply . . . . . 11 5. Security Considerations . . . . . . . . . . . . . . . . . . . 11 6. Manageability Considerations . . . . . . . . . . . . . . . . 11 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12 7.1. New Reply Mode Order TLV . . . . . . . . . . . . . . . . 12 8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 12 9. Contributing Authors . . . . . . . . . . . . . . . . . . . . 12 10. References . . . . . . . . . . . . . . . . . . . . . . . . . 12 10.1. Normative References . . . . . . . . . . . . . . . . . . 13 10.2. Informative References . . . . . . . . . . . . . . . . . 13 Appendix A. Reply Mode Order TLV Beneficial Scenarios . . . . . 13 A.1. Incorrect Forwarding Scenario . . . . . . . . . . . . . . 14 A.2. Non-Co-Routed Bidirectional LSP Scenario . . . . . . . . 14 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 16 Akiya, et al. Expires April 10, 2016 [Page 2] Internet-Draft LSP Ping Reply Mode Simplification October 2015 1. Introduction The Multiprotocol Label Switching (MPLS) Label Switched Path (LSP) Ping, described in [RFC4379], allows an initiator LSR to encode instructions (Reply Mode) on how a responder LSR should send the response back to the initiator LSR. [RFC7110] also allows the initiator LSR to encode a TLV (Reply Path TLV) which can instruct the responder LSR to use a specific LSP to send the response back to the initiator LSR. Both approaches are powerful as they provide the ability for the initiator LSR to control the return path. However, it is becoming increasingly difficult for an initiator LSR to select a valid return path to encode in the MPLS LSP echo request packets. If the initiator LSR does not select a valid return path, the MPLS LSP echo reply will not get back to the initiator LSR. This results in a false failure of MPLS LSP Ping and Traceroute operation. In an effort to minimize such false failures, different implementations have chosen different default return path encoding for different LSP types and LSP operations. The problem with implementations having different default return path encoding is that the MPLS echo reply will not work in many cases, and the default value may not be the preferred choice by the operators. This document describes: o In Section 2, further description of the problems; o In Section 3, a solution to minimize false failures while accommodating operator preferences; o In Section 4, relationships to other LSP Ping/Traceroute features; o In Appendix A, examples of scenarios where the mechanism described in this document provides benefits. This document updates [RFC7110] by allowing the usage of the "Reply via Specified Path" (value=5) Reply Mode without including the Reply Path TLV. The update creates a simple way to indicate that the Reverse LSP should be used as return path. 2. Problem Statements It is becoming increasingly difficult for implementations to automatically supply a workable return path encoding for all MPLS LSP Ping and Traceroute operations across all LSP types. There are several factors which are contributing to this complication. Akiya, et al. Expires April 10, 2016 [Page 3] Internet-Draft LSP Ping Reply Mode Simplification October 2015 o Some LSPs have a control-channel, and some do not. Some LSPs have a reverse LSP, and some do not. Some LSPs have IP reachability in the reverse direction, and some do not. o LSRs on some LSPs can have different available return path(s). Available return path(s) can depend on whether the responder LSR is a transit LSR or an egress LSR. In case of a bi-directional LSP, available return path(s) on transit LSRs can also depend on whether the LSP is completely co-routed, partially co-routed or associated (i.e., the LSPs in the two directions are not co- routed). o MPLS echo request packets may incorrectly terminate on an unintended target, which can have different available return path(s) than the intended target. o The MPLS LSP Ping operation is expected to terminate on an egress LSR. However, the MPLS LSP Ping operation with specific TTL values and MPLS LSP Traceroute operation can terminate on both transit LSR(s) and the egress LSR. Except for the case where the responder LSR does not have an IP route back to the initiator LSR, it is possible to use the "Reply via an IPv4/IPv6 UDP packet" (value=2) Reply Mode value in all cases. However, some operators are preferring control-channel and reverse LSP as default return path if they are available, which is not always the case. When specific return path encoding is supplied by users or applications, then there are no issues in choosing the return path encoding. When specific return path encoding is not supplied by users or applications, then implementations use extra logic to compute, and sometimes guess, the default return path encodings. If a responder LSR receives an MPLS echo request containing return path instructions which cannot be accommodated due to unavailability, then the responder LSR often drops such packets. This failure mode results in the initiator LSR not receiving the intended MPLS LSP echo reply packets. The scenario described here is a potentially acceptable result in some failure cases, like a broken LSP, where the MPLS echo request terminated on an unintended target. However, if the initiator LSR does not receive an MPLS echo replay, even after the responder LSR receives the MPLS echo request and is able to verify the request, information is sent back to the user(s) which is considered a false failure. Many operators prefer particular return path(s) over others return path(s) for specific LSP types. To accommodate operator preferred paths, implementations may default to operator preferred return paths Akiya, et al. Expires April 10, 2016 [Page 4] Internet-Draft LSP Ping Reply Mode Simplification October 2015 for particular operations, or allow a default return path to be configured. It would not be considered beneficial to use a preferred return path for an intended target LSR if there is previous knowledge at the initiator LSR that the return path is not available. Using a unavailable preferred return path would undesirably result in the initiator LSR not receiving the MPLS echo return packets. It would be considered beneficial, for given operations, if the sender of the MPLS echo request would be able to determined return path availability before the operation is initiated. This document updates the procedures for "Reply via Specified Path" Reply Mode to easily indicate the reverse LSP, and adds one optional TLV to describe an ordered list of Reply Modes. Based on operational needs, the TLV can describe multiple Reply Mode values in a preferred order to allow the responder LSR to use the first available Reply Mode from the list. This eliminates the need for the initiator LSR to compute, or sometimes guess, the default return path encoding. This new mode of operation would resulted in a simplification to implementations across the various vendors and improve both usability and operational needs. 3. Solution This document updates the procedures for "Reply via Specified Path" Reply Mode to easily indicate the reverse LSP. This document also adds an optional TLV which can carry an ordered list of Reply Modes. 3.1. Reply via Specified Path Update Some LSP types are capable of having a related LSP in reverse direction, through signaling or other association mechanisms. Examples of such LSP types are bidirectional Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) LSPs [RFC3473] and MPLS Transport Profile (MPLS-TP) LSPs ([RFC5960]). This document uses the term "Reverse LSP" to refer to the LSP in the reverse direction of such LSP types. Note that this document restricts the scope of "Reverse LSP" applicability to those reverse LSPs which are capable and allowed to carry the IP encapsulated MPLS echo reply. [RFC7110] has defined the Reply Mode "Reply via Specified Path" which allows the initiator LSR to instruct the responder LSR to send the MPLS echo reply message on the reverse LSP. However, the instruction also requires the initiator LSR to include the "Reply Path TLV" with the B bit (Bidirectional bit) set in the Flags field. Additionally, [RFC7110] defines that if the "Reply via Specified Path" Reply Mode is used the "Reply Path TLV" MUST present. Akiya, et al. Expires April 10, 2016 [Page 5] Internet-Draft LSP Ping Reply Mode Simplification October 2015 This document updates the procedures for "Reply via Specified Path" Reply Mode as follows: o The "Reply via Specified Path" MAY be used without including a "Reply Path TLV". o The usage of the "Reply via Specified Path" without inclusion of a "Reply Path TLV" implies the reverse LSP. In other words, the usage of the "Reply via Specified Path" without inclusion of a "Reply Path TLV" has the same semantics as the usage of the "Reply via Specified Path" with inclusion of a "Reply Path TLV" with the B bit set in the Flags field. Specific to section 5.1 of [RFC7110], this document updates the first sentence as follows: o When sending an echo request, in addition to the rules and procedures defined in Section 4.3 of [RFC4379], the Reply Mode of the echo request MUST be set to "Reply via Specified Path", and a Reply Path TLV SHOULD be carried in the echo request message correspondingly; if the Reply Path TLV is not carried, then it indicates the reverse LSP as the reply path. Note that the reverse LSP is in relation to the last FEC specified in the Target FEC Stack TLV. 3.2. Reply Mode Order TLV This document also introduces a new optional TLV to describe a list of Reply Mode values. The new TLV will contain one or more Reply Mode value(s) in preferred order. The first Reply Mode value is the most preferred and the last Reply Mode value is the least preferred. Following rules apply when using Reply Mode Order TLV. 1. The Reply Mode Order TLV MUST NOT be included in any MPLS echo reply. If the initiator LSR receives an MPLS echo reply with the Reply Mode Order TLV, the initiator LSR MUST ignore the whole Reply Mode Order TLV and MUST only use the value from the Reply Mode field of the received MPLS echo reply. It may be beneficial for implementations to provide counters and/or loggings, with appropriate log dampening, to record this error case. 2. The Reply Mode Order TLV MAY be included in MPLS echo request. 3. The Reply Mode field of an MPLS echo request MUST be set to a valid value even when supplying the Reply Mode Order TLV. The initiator LSR SHOULD set the Reply Mode field of an MPLS echo request to a value that corresponds to a return path which most Akiya, et al. Expires April 10, 2016 [Page 6] Internet-Draft LSP Ping Reply Mode Simplification October 2015 likely to be available, in case the responder LSR does not understand the Reply Mode Order TLV. 4. If a responder LSR understands the Reply Mode Order TLV but the TLV is not valid (due to conditions described in the items 6, 7, 8 and 9 immediately below), then the responder LSR MUST ignore the whole Reply Mode Order TLV and MUST only use the value from the Reply Mode field of the received MPLS echo request. It may be beneficial for implementations to provide counters and/or loggings, with appropriate log dampening, to record this error case. 5. If a responder LSR understands the Reply Mode Order TLV and the TLV is valid, then the responder LSR MUST consider the Reply Mode values described in the TLV and MUST NOT use the value described in the Reply Mode field of the received MPLS echo request. In other words, a valid Reply Mode Order TLV overrides the value specified in the Reply Mode field of the received MPLS echo request. 6. Reply Mode Order TLV MUST contain at least one Reply Mode value. 7. A Reply Mode value, except for Reply Mode value 5 (Reply via Specified Path), MUST NOT be repeated (i.e., MUST NOT appear multiple times) in the Reply Mode Order TLV. 8. The Reply Mode value 5 (Reply via Specified Path) MAY be included more than once in the Reply Mode Order TLV. However, in such case a Reply Path TLV MUST be included for all instances of the Reply Mode value 5 included in the Reply Mode Order TLV. In other words, 3 instances of the Reply Mode value 5 in the Reply Mode Order TLV will require 3 instances of the Reply Path TLVs. 9. The Reply Mode value 1 (Do not reply) MUST NOT be used in the Reply Mode Order TLV. The responder LSR SHOULD select the first available return path in this TLV. The Reply Mode value corresponding to the selected return path MUST be set in Reply Mode field of the MPLS echo reply to communicate back to the initiator LSR which return path was chosen. The format of the TLV is as follows: Akiya, et al. Expires April 10, 2016 [Page 7] Internet-Draft LSP Ping Reply Mode Simplification October 2015 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Reply Mode Order TLV Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ ~ Reply Mode 1 | Reply Mode 2 | Reply Mode 3 | Reply Mode 4 ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 1 Reply Mode Order TLV This is a variable length optional TLV. The Reply Mode Order TLV Type is TBD1. The Length field is 2 octets in length. It defines the length in octets of the list of Reply Mode values. Each Reply Mode field is 1 octet, and there is no padding. 4. Relations to Other LSP Ping/Trace Features 4.1. Backwards Compatibility with Reply via Specified Path Reply Mode [RFC7110] introduces the "Reply via Specified Path" (value=5) Reply Mode. The RFC also defines that if this Reply Mode is used, the "Reply Path TLV" MUST be included. This document relaxes the semantics and defines that this Reply Mode MAY be used without the "Reply Path TLV". This MAY be done to indicate that the reverse LSP SHALL be used as he return path. If the initiator LSR, which sent an MPLS echo request message with the "Reply via Specified Path" Reply Mode but without including the "Reply Path TLV", receives back an MPLS echo reply message with the return code being "Malformed echo request received", then the initiator LSR SHOULD assume that the responder LSR does not support the mechanism defined in this document. 4.2. Reply Path TLV A "Reply Path TLV" [RFC7110] is defined to identify a single return path. When the initiator LSR wants to use the Reply Mode Order TLV to describe multiple return paths, then the initiator SHOULD include multiple "Reply via Specified Path" (value=5) Reply Mode values and multiple corresponding "Reply Path TLV" objects (one "Reply Path TLV" corresponding to a "Reply via Specified Path" Reply Mode, and one "Reply Path TLV" identifies a return path). As described in Section 3.1, it's valid to use the "Reply via Specified Path" Reply Mode without inclusion a "Reply Path TLV". For the Reply Mode Order TLV, it's also valid to include a "Reply via Akiya, et al. Expires April 10, 2016 [Page 8] Internet-Draft LSP Ping Reply Mode Simplification October 2015 Specified Path" Reply Mode value without a corresponding "Reply Path TLV", this implies that the reverse LSP is the preferred return path. When multiple consecutive "Reply via Specified Path" Reply Mode values are included but less corresponding "Reply Path TLV" objects exist, the responder LSR SHOULD think that the former "Reply via Specified Path" Reply Mode values have corresponding "Reply Path TLV", the latter "Reply via Specified Path" Reply Mode values have no corresponding "Reply Path TLV". For example, if the Reply Mode Order TLV carrying Reply Modes {5, 5, 5} and only two Reply Path TLVs carrying FEC X and FEC Y respectively. The reply path order is as follows: 1. Reply via Specified Path (FEC X) 2. Reply via Specified Path (FEC Y) 3. Reply via Specified Path (Reverse LSP) 4.2.1. Example 1: Reply Mode Order TLV Usage with Reply Path TLV If the initiator LSR was interested in encoding following return paths: 1. Reply via application level control channel 2. FEC X 3. FEC Y 4. Reply via an IPv4/IPv6 UDP packet Then the MPLS echo request message is to carry: o The Reply Mode Order TLV carrying Reply Modes {4, 5, 5, 2} o One Reply Path TLV carrying FEC X o One Reply Path TLV carrying FEC Y Described encoding of the Reply Mode Order TLV and the Reply Path TLV in the MPLS echo request message will result in the responder LSR to prefer "Reply via application level control channel (4)", followed by FEC X, FEC Y and then "Reply via an IPv4/IPv6 UDP packet (2)". Akiya, et al. Expires April 10, 2016 [Page 9] Internet-Draft LSP Ping Reply Mode Simplification October 2015 4.2.2. Example 2: Reply Mode Order TLV Usage with Reply Path TLV If the initiator LSR was interested in encoding following return paths: 1. Reverse LSP 2. Reply via an IPv4/IPv6 UDP packet 3. FEC X 4. FEC Y Then the MPLS echo request message is to carry: o The Reply Mode Order TLV carrying Reply Modes {5, 2, 5, 5} o One Reply Path TLV with the B bit set. o One Reply Path TLV carrying FEC X o One Reply Path TLV carrying FEC Y Described encoding of the Reply Mode Order TLV and the Reply Path TLV in the MPLS echo request message will result in the responder LSR to prefer the reverse LSP, followed by "Reply via an IPv4/IPv6 UDP packet (2)", FEC X and then FEC Y. 4.3. Proxy LSP Ping The mechanism defined in this document will work with Proxy LSP Ping defined by [RFC7555]. The MPLS proxy ping request message can carry a Reply Mode value in the header and one or more Reply Mode values in the Reply Mode Order TLV. It is RECOMMENDED that the Reply Mode 2 (Reply via an IPv4/IPv6 UDP packet) be used in the Reply Mode field of the MPLS proxy ping request message. 4.3.1. Proxy LSR Sending an MPLS Echo Request If the proxy LSR is sending an MPLS echo request, then the proxy LSR MUST copy the following elements from the MPLS proxy ping request message to the MPLS echo request message. o The Reply Mode field. o The Reply Mode Order TLV. Akiya, et al. Expires April 10, 2016 [Page 10] Internet-Draft LSP Ping Reply Mode Simplification October 2015 o The Reply Path TLV(s). If there are more than one Reply Path TLVs, then order of them MUST be preserved when copying. 4.3.2. Proxy LSR Sending an MPLS Proxy Ping Reply If the proxy LSR is sending an MPLS proxy ping reply, then it is RECOMMENDED that the Reply Mode Order TLV is ignored and the Reply Mode field in the MPLS proxy ping request message is used. 5. Security Considerations Those security considerations specified in [RFC4379] and [RFC7110] apply for this document. In addition, this document introduces the Reply Mode Order TLV. It provides a new way for an unauthorized source to gather more network information, especially the potential return path(s) information of an LSP. To protect against unauthorized sources using MPLS echo request messages with the Reply Mode Order TLV to obtain network information, similar to [RFC4379], it is RECOMMENDED that implementations provide a means of checking the source addresses of MPLS echo request messages against an access list before accepting the message. Another potential security issue is that the MPLS echo request and reply messages are not encrypted, the content of the MPLS echo request and reply messages may be potentially exposed. Although the exposure is within the MPLS domain, if such exposure is a concern, some encryption mechanisms [I-D.ietf-mpls-opportunistic-encrypt] may be employed. 6. Manageability Considerations Section 2 described the problems which increases the complexity with respect to operations and implementations. In order to simplify operations and to allow for the LSP Ping/Traceroute to function efficiently whilst preserving the code simplicity, it is RECOMMENDED that implementations allow devices to have configuration options to set operator preferred Reply Modes. For example: o For those operators who are more interested in MPLS echo reply packets reaching back to the initiator LSR: 1. Reply via an IPv4/IPv6 UDP packet (2) 2. Reply via application level control channel (4) 3. Reply via Specified Path (5) Akiya, et al. Expires April 10, 2016 [Page 11] Internet-Draft LSP Ping Reply Mode Simplification October 2015 o For those operators who are more interested in MPLS echo reply packets testing the paths related to the forward LSP: 1. Reply via Specified Path (5) 2. Reply via application level control channel (4) 3. Reply via an IPv4/IPv6 UDP packet (2) 7. IANA Considerations 7.1. New Reply Mode Order TLV IANA is requested to assign a new TLV type value from the "TLVs" sub- registry within the "Multiprotocol Label Switching Architecture (MPLS)" registry, for the "Reply Mode Order TLV". The new TLV Type value should be assigned from the range (32768-49161) specified in [RFC4379] section 3 that allows the TLV type to be silently dropped if not recognized. Type Meaning Reference ---- ------- --------- TBD1 Reply Mode Order TLV this document 8. Acknowledgements Authors would like to thank Santiago Alvarez and Faisal Iqbal for discussions which motivated creation of this document. Authors would also like to thank Sam Aldrin, Curtis Villamizar, Ross Callon, Jeffrey Zhang, Jeremy Whittaker, Mustapha Alissaoui, Qin Wu, Jie Dong and Adrian Farrel for providing valuable comments to influence the contents of the draft. Authors would also like to thank Dan Frost, Tom Taylor, Victor Kuarsingh and Deborah Brungard for reviewing the document and providing useful comments. 9. Contributing Authors Shaleen Saxena Brocade Email: ssaxena@brocade.com 10. References Akiya, et al. Expires April 10, 2016 [Page 12] Internet-Draft LSP Ping Reply Mode Simplification October 2015 10.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, March 1997, . [RFC4379] Kompella, K. and G. Swallow, "Detecting Multi-Protocol Label Switched (MPLS) Data Plane Failures", RFC 4379, DOI 10.17487/RFC4379, February 2006, . [RFC7110] Chen, M., Cao, W., Ning, S., Jounay, F., and S. Delord, "Return Path Specified Label Switched Path (LSP) Ping", RFC 7110, DOI 10.17487/RFC7110, January 2014, . 10.2. Informative References [I-D.ietf-mpls-opportunistic-encrypt] Farrel, A. and S. Farrell, "Opportunistic Security in MPLS Networks", draft-ietf-mpls-opportunistic-encrypt-00 (work in progress), July 2015. [RFC3473] Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol- Traffic Engineering (RSVP-TE) Extensions", RFC 3473, DOI 10.17487/RFC3473, January 2003, . [RFC5960] Frost, D., Ed., Bryant, S., Ed., and M. Bocci, Ed., "MPLS Transport Profile Data Plane Architecture", RFC 5960, DOI 10.17487/RFC5960, August 2010, . [RFC7555] Swallow, G., Lim, V., and S. Aldrin, "Proxy MPLS Echo Request", RFC 7555, DOI 10.17487/RFC7555, June 2015, . Appendix A. Reply Mode Order TLV Beneficial Scenarios This section lists examples of how the Reply Mode Order TLV can benefit. Akiya, et al. Expires April 10, 2016 [Page 13] Internet-Draft LSP Ping Reply Mode Simplification October 2015 A.1. Incorrect Forwarding Scenario As shown in Figure 2, a network has an LSP with the forwarding path: A-B-C-D-E. The LSP has a control channel. A------B------C------D------E | | F Forward Paths: A-B-C-D-E Figure 2: Incorrect Forwarding If D is incorrectly label switching to F (instead of E). In this scenario, LSP Traceroute with "Reply via application level control channel (4)" will result in following result. Success (Reply from B) Success (Reply from C) Success (Reply from D) Timeout... Complete This is because F does not have a control channel to send the MPLS echo reply message. With the extension described in this document, same procedures can be performed with the Reply Mode Order TLV carrying {4, 2}. When LSP Traceroute is issued, then following output may be displayed without any unnecessary timeout. Success (Reply from B, Reply Mode: 4) Success (Reply from C, Reply Mode: 4) Success (Reply from D, Reply Mode: 4) FEC Mismatch (Reply from F, Reply Mode: 2) Complete The result provides more diagnostic information to the initiator LSR, and without any delay (i.e. timeout from one or more downstream LSRs). A.2. Non-Co-Routed Bidirectional LSP Scenario As shown in Figure 3, a network has a bidirectional LSP where the forward LSP and the reverse LSP are not fully co-routed. Akiya, et al. Expires April 10, 2016 [Page 14] Internet-Draft LSP Ping Reply Mode Simplification October 2015 +----C------D----+ / \ A------B G------H \ / +----E------F----+ Forward Paths: A-B-C-D-G-H (upper path) Reverse Paths: H-G-F-E-B-A (lower path) Figure 3: Non-Co-Routed Bidirectional LSP Some operators may prefer and configure the system to default the Reply Mode to indicate the reverse LSP when MPLS echo request messages are sent on bidirectional LSPs. Without extensions described in this document, following behaviors will be seen: o When LSP Ping is issued from A, the reply will come back on the reverse LSP from H. o When LSP Traceroute is issued from A, the replies will come back on the reverse LSP from B, G and H, but will encounter a timeout from C and D as there are no reverse LSP on those nodes. o When LSP Ping with specific TTL value is issued from A, whether a timeout will be encountered depends on the value of the TTL used (i.e. whether or not the MPLS echo request terminates on a node that has reverse LSP). One can argue that the initiator LSR can automatically generate the same MPLS echo request with different Reply Mode value to those nodes that timeout. However, such mechanism will result in extended time for the entire operation to complete (i.e. multiple seconds to multiple minutes). This is undesirable, and perhaps unacceptable if the "user" is an application. With the extension described in this document, same procedures can be performed with the Reply Mode Order TLV carrying {5, 2}. When LSP Traceroute is issued, then following output may be displayed without any unnecessary timeout. Success (Reply Mode: 5) Success (Reply Mode: 2) Success (Reply Mode: 2) Success (Reply Mode: 5) Success (Reply Mode: 5) Complete Akiya, et al. Expires April 10, 2016 [Page 15] Internet-Draft LSP Ping Reply Mode Simplification October 2015 Authors' Addresses Nobo Akiya Big Switch Networks Email: nobo.akiya.dev@gmail.com George Swallow Cisco Systems Email: swallow@cisco.com Carlos Pignataro Cisco Systems Email: cpignata@cisco.com Loa Andersson Huawei Email: loa@mail01.huawei.com Mach(Guoyi) Chen Huawei Email: mach.chen@huawei.com Akiya, et al. Expires April 10, 2016 [Page 16]