L3SM Working Group S. Litkowski Internet-Draft Orange Business Service Intended status: Standards Track R. Shakir Expires: September 4, 2016 BT L. Tomotaki Verizon K. D'Souza ATT March 03, 2016 YANG Data Model for L3VPN service delivery draft-ietf-l3sm-l3vpn-service-model-04 Abstract This document defines a YANG data model that can be used to deliver a Layer 3 Provider Provisioned VPN service. The document is limited to the BGP PE-based VPNs as described in RFC4110 and RFC4364. This model is intended to be instantiated at management system to deliver the overall service. This model is not a configuration model to be used directly on network elements. This model provides an abstracted view of the Layer 3 IPVPN service configuration components. It will be up to a management system to take this as an input and use specific configurations models to configure the different network elements to deliver the service. How configuration of network elements is done is out of scope of the document. Requirements Language The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC2119]. Status of This Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." Litkowski, et al. Expires September 4, 2016 [Page 1] Internet-Draft l3vpn-svc-cfg March 2016 This Internet-Draft will expire on September 4, 2016. Copyright Notice Copyright (c) 2016 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1. Terminology . . . . . . . . . . . . . . . . . . . . . . . 3 1.2. Tree diagram . . . . . . . . . . . . . . . . . . . . . . 4 2. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Layer 3 IP VPN service model . . . . . . . . . . . . . . . . 5 4. Service data model usage . . . . . . . . . . . . . . . . . . 5 5. Design of the Data Model . . . . . . . . . . . . . . . . . . 6 5.1. VPN service overview . . . . . . . . . . . . . . . . . . 14 5.1.1. VPN service topology . . . . . . . . . . . . . . . . 14 5.1.1.1. Route Target allocation . . . . . . . . . . . . . 15 5.1.1.2. Any to any . . . . . . . . . . . . . . . . . . . 16 5.1.1.3. Hub and Spoke . . . . . . . . . . . . . . . . . . 16 5.1.1.4. Hub and Spoke disjoint . . . . . . . . . . . . . 17 5.1.2. Cloud access . . . . . . . . . . . . . . . . . . . . 17 5.1.3. Multicast service . . . . . . . . . . . . . . . . . . 19 5.1.4. Extranet VPNs . . . . . . . . . . . . . . . . . . . . 20 5.2. Site overview . . . . . . . . . . . . . . . . . . . . . . 22 5.2.1. Site role . . . . . . . . . . . . . . . . . . . . . . 23 5.2.2. Site belonging to multiple VPNs . . . . . . . . . . . 24 5.2.2.1. Site vpn flavor . . . . . . . . . . . . . . . . . 24 5.2.2.2. VPN policy . . . . . . . . . . . . . . . . . . . 25 5.2.3. Security . . . . . . . . . . . . . . . . . . . . . . 27 5.2.3.1. Encryption . . . . . . . . . . . . . . . . . . . 27 5.2.4. Management . . . . . . . . . . . . . . . . . . . . . 27 5.2.5. Routing protocols . . . . . . . . . . . . . . . . . . 28 5.2.5.1. Dual stack handling . . . . . . . . . . . . . . . 28 5.2.5.2. Direct LAN connection onto SP network . . . . . . 29 5.2.5.3. Direct LAN connection onto SP network with redundancy . . . . . . . . . . . . . . . . . . . 29 Litkowski, et al. Expires September 4, 2016 [Page 2] Internet-Draft l3vpn-svc-cfg March 2016 5.2.5.4. Static routing . . . . . . . . . . . . . . . . . 30 5.2.5.5. RIP routing . . . . . . . . . . . . . . . . . . . 30 5.2.5.6. OSPF routing . . . . . . . . . . . . . . . . . . 30 5.2.5.7. BGP routing . . . . . . . . . . . . . . . . . . . 32 5.2.6. Service . . . . . . . . . . . . . . . . . . . . . . . 34 5.2.6.1. QoS . . . . . . . . . . . . . . . . . . . . . . . 34 5.2.6.2. Multicast . . . . . . . . . . . . . . . . . . . . 39 5.2.7. Site network accesses . . . . . . . . . . . . . . . . 39 5.2.7.1. Bearer . . . . . . . . . . . . . . . . . . . . . 39 5.2.7.2. Connection . . . . . . . . . . . . . . . . . . . 39 5.2.8. Deciding where to connect the site . . . . . . . . . 40 5.2.8.1. Site location . . . . . . . . . . . . . . . . . . 40 5.2.8.2. Site diversity . . . . . . . . . . . . . . . . . 41 5.2.8.3. Site network access availability . . . . . . . . 42 5.2.8.4. Route Distinguisher and VRF allocation . . . . . 44 5.3. Enhanced VPN features . . . . . . . . . . . . . . . . . . 45 5.3.1. Carrier Supporting Carrier . . . . . . . . . . . . . 45 5.3.2. Transport constraints . . . . . . . . . . . . . . . . 47 5.4. Using configuration templates . . . . . . . . . . . . . . 47 6. Service model usage example . . . . . . . . . . . . . . . . . 52 7. Interaction with Other YANG Modules . . . . . . . . . . . . . 56 8. YANG Module . . . . . . . . . . . . . . . . . . . . . . . . . 60 9. Security Considerations . . . . . . . . . . . . . . . . . . . 103 10. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 104 11. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 104 12. References . . . . . . . . . . . . . . . . . . . . . . . . . 104 12.1. Normative References . . . . . . . . . . . . . . . . . . 104 12.2. Informative References . . . . . . . . . . . . . . . . . 105 Appendix A. Example: NETCONF Reply . . . . . . . . . . . . 105 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 105 1. Introduction This document defines a YANG data model for Layer 3 IPVPN service configuration. 1.1. Terminology The following terms are defined in [RFC6241] and are not redefined here: o client o configuration data o server o state data Litkowski, et al. Expires September 4, 2016 [Page 3] Internet-Draft l3vpn-svc-cfg March 2016 The following terms are defined in [RFC6020] and are not redefined here: o augment o data model o data node The terminology for describing YANG data models is found in [RFC6020]. 1.2. Tree diagram A simplified graphical representation of the data model is presented in Section 5. The meaning of the symbols in these diagrams is as follows: o Brackets "[" and "]" enclose list keys. o Curly braces "{" and "}" contain names of optional features that make the corresponding node conditional. o Abbreviations before data node names: "rw" means configuration (read-write), and "ro" state data (read-only). o Symbols after data node names: "?" means an optional node and "*" denotes a "list" or "leaf-list". o Parentheses enclose choice and case nodes, and case nodes are also marked with a colon (":"). o Ellipsis ("...") stands for contents of subtrees that are not shown. 2. Definitions Customer Edge (CE) Device: The equipment on the customer side of the SP-customer boundary (the customer interface). Provider Edge (PE) Device: The equipment on the SP side of the SP- customer boundary (the customer interface). PE-Based VPNs: The PE devices know that certain traffic is VPN traffic. They forward the traffic (through tunnels) based on the destination IP address of the packet, and optionally on based on other information in the IP header of the packet. The PE devices are Litkowski, et al. Expires September 4, 2016 [Page 4] Internet-Draft l3vpn-svc-cfg March 2016 themselves the tunnel endpoints. The tunnels may make use of various encapsulations to send traffic over the SP network (such as, but not restricted to, GRE, IP-in-IP, IPsec, or MPLS tunnels). 3. Layer 3 IP VPN service model A Layer 3 IPVPN service is a collection of sites that are authorized to exchange traffic between each other over a shared IP infrastructure. This layer 3 VPN service model aims at providing a common understanding on how the corresponding IP VPN service is to be deployed over the shared infrastructure. This service model is limited to BGP PE-Based VPNs as described in [RFC4110] and [RFC4364]. 4. Service data model usage L3VPN-SVC | MODEL | | +------------------+ +-----+ | Orchestration | < --- > | OSS | +------------------+ +-----+ | | +----------------+ | | Config manager | | +----------------+ | | | | Netconf/CLI ... | | +------------------------------------------------+ Network +++++++ + AAA + +++++++ +++++++ Bearer ++++++++ ++++++++ +++++++ + CEA + ------- + PE A + + PE B + ----- + CEB + +++++++ Cnct ++++++++ ++++++++ +++++++ Site A Site B The idea of the L3 IPVPN service model is to propose an abstracted interface to manage configuration of components of a L3VPN service. A typical usage is to use this model as an input for an orchestration layer who will be responsible to translate it to orchestrated configuration of network elements who will be part of the service. Litkowski, et al. Expires September 4, 2016 [Page 5] Internet-Draft l3vpn-svc-cfg March 2016 The network elements can be routers, but also servers (like AAA), and not limited to these examples. The configuration of network elements MAY be done by CLI, or by NetConf/RestConf coupled with specific configuration YANG data models (BGP, VRF, BFD ...) or any other way. The usage of this service model is not limited to this example, it can be used by any component of the management system but not directly by network elements. 5. Design of the Data Model The YANG module is divided in three main containers : vpn-svc, sites, site-templates. The vpn-svc defines global parameters for the VPN service for a specific customer. A site is composed of at least one site-network-access and may have multiple site-network-access in case of multihoming. The site- network-access attachment is done through a bearer with a connection (transport protocol) on top. The bearer refers to physical properties of the attachment while the connection refers to more protocol oriented properties. Authorization of traffic exchange is done through what we call a VPN policy or VPN topology defining routing exchange rules between sites. The site-templates may be used as configuration templates for sites. Part of the site configuration can be inherited from templates. The figure below describe the overall structure of the YANG module: module: ietf-l3vpn-svc +--rw l3vpn-svc +--rw vpn-services | +--rw vpn-svc* [vpn-id] | +--rw vpn-id svc-id | +--rw customer-name? string | +--rw topology? identityref | +--rw cloud-access* [cloud-identifier] | | +--rw cloud-identifier string | | +--rw authorized-sites* [site-id] | | | +--rw site-id leafref | | +--rw denied-sites* [site-id] | | | +--rw site-id leafref | | +--rw nat-enabled? boolean | | +--rw customer-nat-address? inet:ipv4-address | +--rw multicast Litkowski, et al. Expires September 4, 2016 [Page 6] Internet-Draft l3vpn-svc-cfg March 2016 | | +--rw enabled? boolean | | +--rw customer-tree-flavors | | | +--rw tree-flavor* [type] | | | +--rw type identityref | | +--rw rp | | +--rw rp-group-mapping* [rp-address group] | | | +--rw provider-managed | | | | +--rw enabled? boolean | | | | +--rw anycast-rp? boolean | | | +--rw rp-address union | | | +--rw group union | | +--rw rp-discovery? identityref | +--rw mpls? boolean | +--rw transport-constraints | | +--rw unicast-transport-constraints | | | +--rw constraints* [constraint-id] | | | +--rw constraint-id svc-id | | | +--rw site1? svc-id | | | +--rw site2? svc-id | | | +--rw constraint-list* [constraint-type] | | | +--rw constraint-type identityref | | | +--rw constraint-opaque-value? string | | +--rw multicast-transport-constraints | | +--rw constraints* [constraint-id] | | +--rw constraint-id svc-id | | +--rw src-site? svc-id | | +--rw dst-site? svc-id | | +--rw constraint-list* [constraint-type] | | +--rw constraint-type identityref | | +--rw constraint-opaque-value? string | +--rw extranet-vpns | +--rw extranet-vpn* [vpn-id] | +--rw vpn-id svc-id | +--rw local-sites-role? identityref +--rw sites | +--rw site* [site-id] | +--rw site-id svc-id | +--rw apply-template? leafref | +--rw requested-site-start? yang:date-and-time | +--rw requested-site-stop? yang:date-and-time | +--rw actual-site-start? yang:date-and-time | +--rw actual-site-stop? yang:date-and-time | +--rw location | | +--rw address? string | | +--rw zip-code? string | | +--rw city? string | | +--rw country-code? string | +--rw site-diversity Litkowski, et al. Expires September 4, 2016 [Page 7] Internet-Draft l3vpn-svc-cfg March 2016 | | +--rw type? placement-diversity | | +--rw site-group* uint32 | +--rw management | | +--rw type? identityref | | +--rw management-transport? identityref | | +--rw address? union | +--rw vpn-policy | | +--rw entries* [id] | | +--rw id svc-id | | +--rw filter | | | +--rw (lan)? | | | +--:(lan-prefix) | | | | ... | | | +--:(lan-tag) | | | ... | | +--rw vpn | | +--rw vpn-id leafref | | +--rw site-role identityref | +--rw site-vpn-flavor? identityref | +--rw maximum-routes | | +--rw address-family* [af] | | +--rw af identityref | | +--rw maximum-routes? uint32 | +--rw security | | +--rw authentication | | +--rw encryption | | +--rw enabled? boolean | | +--rw layer? enumeration | | +--rw encryption-profile | | +--rw (profile)? | | +--:(provider-profile) | | | ... | | +--:(customer-profile) | | ... | +--rw service | | +--rw svc-input-bandwidth? uint32 | | +--rw svc-output-bandwidth? uint32 | | +--rw svc-mtu? uint16 | | +--rw qos | | | +--rw qos-classification-policy | | | | +--rw rules* [id] | | | | +--rw id uint16 | | | | +--rw match-flow | | | | | ... | | | | +--rw target-class-id? string | | | +--rw (qos-profile)? | | | +--:(standard) | | | | +--rw profile? string Litkowski, et al. Expires September 4, 2016 [Page 8] Internet-Draft l3vpn-svc-cfg March 2016 | | | +--:(custom) | | | +--rw classes | | | ... | | +--rw mpls | | | +--rw signalling-type? enumeration | | +--rw multicast | | +--rw multicast-site-type? enumeration | | +--rw multicast-transport-protocol | | | +--rw ipv4? boolean | | | +--rw ipv6? boolean | | +--rw protocol-type? enumeration | +--rw routing-protocols | | +--rw routing-protocol* [type] | | +--rw type identityref | | +--rw ospf | | | +--rw address-family* identityref | | | +--rw area-address? yang:dotted-quad | | | +--rw metric? uint16 | | | +--rw sham-link* [target-site] | | | +--rw target-site svc-id | | | +--rw metric? uint16 | | +--rw bgp | | | +--rw autonomous-system? uint32 | | | +--rw address-family* identityref | | +--rw static | | | +--rw cascaded-lan-prefixes | | | +--rw ipv4-lan-prefixes* [lan next-hop] | | | | ... | | | +--rw ipv6-lan-prefixes* [lan next-hop] | | | ... | | +--rw rip | | | +--rw address-family* identityref | | +--rw vrrp | | +--rw address-family* identityref | +--rw site-network-accesses | +--rw site-network-access* [site-network-access-id] | +--rw site-network-access-id svc-id | +--rw apply-template? leafref | +--rw access-diversity | | +--rw type? placement-diversity | +--rw bearer | | +--rw type? string | | +--rw bearer-reference? string | +--rw ip-connection | | +--rw ipv4 | | | +--rw address-allocation-type? identityref | | | +--rw (subnet)? | | | ... Litkowski, et al. Expires September 4, 2016 [Page 9] Internet-Draft l3vpn-svc-cfg March 2016 | | +--rw ipv6 | | | +--rw address-allocation-type? string | | | +--rw (subnet)? | | | ... | | +--rw oam | | +--rw bfd | | ... | +--rw security | | +--rw authentication | | +--rw encryption | | +--rw enabled? boolean | | +--rw layer? enumeration | | +--rw encryption-profile | | ... | +--rw service | | +--rw svc-input-bandwidth? uint32 | | +--rw svc-output-bandwidth? uint32 | | +--rw svc-mtu? uint16 | | +--rw qos | | | +--rw qos-classification-policy | | | | ... | | | +--rw (qos-profile)? | | | ... | | +--rw mpls | | | +--rw signalling-type? enumeration | | +--rw multicast | | +--rw multicast-site-type? enumeration | | +--rw multicast-transport-protocol | | | ... | | +--rw protocol-type? enumeration | +--rw routing-protocols | | +--rw routing-protocol* [type] | | +--rw type identityref | | +--rw ospf | | | ... | | +--rw bgp | | | ... | | +--rw static | | | ... | | +--rw rip | | | ... | | +--rw vrrp | | ... | +--rw availability | +--rw traffic-protection | | +--rw enabled? boolean | +--rw access-priority? uint32 +--rw site-templates Litkowski, et al. Expires September 4, 2016 [Page 10] Internet-Draft l3vpn-svc-cfg March 2016 +--rw site-template* [site-template-id] +--rw site-template-id template-id +--rw requested-site-start? yang:date-and-time +--rw requested-site-stop? yang:date-and-time +--rw actual-site-start? yang:date-and-time +--rw actual-site-stop? yang:date-and-time +--rw location | +--rw address? string | +--rw zip-code? string | +--rw city? string | +--rw country-code? string +--rw site-diversity | +--rw type? placement-diversity | +--rw site-group* uint32 +--rw management | +--rw type? identityref | +--rw management-transport? identityref | +--rw address? union +--rw vpn-policy | +--rw entries* [id] | +--rw id svc-id | +--rw filter | | +--rw (lan)? | | +--:(lan-prefix) | | | ... | | +--:(lan-tag) | | ... | +--rw vpn | +--rw vpn-id leafref | +--rw site-role identityref +--rw site-vpn-flavor? identityref +--rw maximum-routes | +--rw address-family* [af] | +--rw af identityref | +--rw maximum-routes? uint32 +--rw security | +--rw authentication | +--rw encryption | +--rw enabled? boolean | +--rw layer? enumeration | +--rw encryption-profile | +--rw (profile)? | +--:(provider-profile) | | ... | +--:(customer-profile) | ... +--rw service | +--rw svc-input-bandwidth? uint32 Litkowski, et al. Expires September 4, 2016 [Page 11] Internet-Draft l3vpn-svc-cfg March 2016 | +--rw svc-output-bandwidth? uint32 | +--rw svc-mtu? uint16 | +--rw qos | | +--rw qos-classification-policy | | | +--rw rules* [id] | | | +--rw id uint16 | | | +--rw match-flow | | | | ... | | | +--rw target-class-id? string | | +--rw (qos-profile)? | | +--:(standard) | | | +--rw profile? string | | +--:(custom) | | +--rw classes | | ... | +--rw mpls | | +--rw signalling-type? enumeration | +--rw multicast | +--rw multicast-site-type? enumeration | +--rw multicast-transport-protocol | | +--rw ipv4? boolean | | +--rw ipv6? boolean | +--rw protocol-type? enumeration +--rw routing-protocols | +--rw routing-protocol* [type] | +--rw type identityref | +--rw ospf | | +--rw address-family* identityref | | +--rw area-address? yang:dotted-quad | | +--rw metric? uint16 | | +--rw sham-link* [target-site] | | +--rw target-site svc-id | | +--rw metric? uint16 | +--rw bgp | | +--rw autonomous-system? uint32 | | +--rw address-family* identityref | +--rw static | | +--rw cascaded-lan-prefixes | | +--rw ipv4-lan-prefixes* [lan next-hop] | | | ... | | +--rw ipv6-lan-prefixes* [lan next-hop] | | ... | +--rw rip | | +--rw address-family* identityref | +--rw vrrp | +--rw address-family* identityref +--rw site-network-access +--rw access-diversity Litkowski, et al. Expires September 4, 2016 [Page 12] Internet-Draft l3vpn-svc-cfg March 2016 | +--rw type? placement-diversity +--rw bearer | +--rw type? string | +--rw bearer-reference? string +--rw ip-connection | +--rw ipv4 | | +--rw address-allocation-type? identityref | | +--rw (subnet)? | | +--:(subnet-only) | | | ... | | +--:(addresses) | | ... | +--rw ipv6 | | +--rw address-allocation-type? string | | +--rw (subnet)? | | +--:(subnet-only) | | | ... | | +--:(addresses) | | ... | +--rw oam | +--rw bfd | +--rw bfd-enabled? boolean | +--rw (holdtime)? | ... +--rw security | +--rw authentication | +--rw encryption | +--rw enabled? boolean | +--rw layer? enumeration | +--rw encryption-profile | +--rw (profile)? | ... +--rw service | +--rw svc-input-bandwidth? uint32 | +--rw svc-output-bandwidth? uint32 | +--rw svc-mtu? uint16 | +--rw qos | | +--rw qos-classification-policy | | | +--rw rules* [id] | | | ... | | +--rw (qos-profile)? | | +--:(standard) | | | ... | | +--:(custom) | | ... | +--rw mpls | | +--rw signalling-type? enumeration | +--rw multicast Litkowski, et al. Expires September 4, 2016 [Page 13] Internet-Draft l3vpn-svc-cfg March 2016 | +--rw multicast-site-type? enumeration | +--rw multicast-transport-protocol | | +--rw ipv4? boolean | | +--rw ipv6? boolean | +--rw protocol-type? enumeration +--rw routing-protocols | +--rw routing-protocol* [type] | +--rw type identityref | +--rw ospf | | +--rw address-family* identityref | | +--rw area-address? yang:dotted-quad | | +--rw metric? uint16 | | +--rw sham-link* [target-site] | | ... | +--rw bgp | | +--rw autonomous-system? uint32 | | +--rw address-family* identityref | +--rw static | | +--rw cascaded-lan-prefixes | | ... | +--rw rip | | +--rw address-family* identityref | +--rw vrrp | +--rw address-family* identityref +--rw availability +--rw traffic-protection | +--rw enabled? boolean +--rw access-priority? uint32 5.1. VPN service overview The vpn-svc top container contains generic information about the VPN service. The vpn-id of the vpn-svc refers to an internal reference for this VPN service, while customer name refers to a more explicit reference to the customer. This identifier is purely internal to the organization responsible for the VPN service. The vpn-id MUST be unique. 5.1.1. VPN service topology The type of topology of the VPN is required for configuration. Current proposal supports : any-to-any, hub and spoke (where hubs can exchange traffic), and hub and spoke disjoint (where hubs cannot exchange traffic). New topologies could be added by augmentation. By default, any-to-any topology is used. Litkowski, et al. Expires September 4, 2016 [Page 14] Internet-Draft l3vpn-svc-cfg March 2016 5.1.1.1. Route Target allocation Layer 3 PE-based VPN is built using route-targets as described in [RFC4364]. It is expected management system to allocate automatically set of route-targets upon a VPN service creation request. How management system allocates route-targets is out of scope of the document but multiple ways could be envisaged as described below. Management system <-------------------------------------------------> Request RT +-----------------------+ Topo a2a +----------+ RestConf | | -----> | | User ------------- | Service Orchestration | |NetworkOSS| l3vpn-svc | | <----- | | model +-----------------------+ Response +----------+ RT1,RT2 In the example above, a service orchestration, owning the instantiation of this service model, request route-targets to the network OSS. Based on the requested VPN topology, the network OSS replies with one or multiple route-targets. The interface between this service orchestration and network OSS is out of scope of this document. +---------------------------+ RestConf | | User ------------- | Service Orchestration | l3vpn-svc | | model | | | RT pool : 10:1->10:10000 | | RT pool : 20:50->20:5000 | +---------------------------+ In the example above, a service orchestration, owning the instantiation of this service model, owns one or more pools of route- target (filled by service provider) that can be allocated. Based on the requested VPN topology, it will allocate one or multiple route- targets from the pool. The mechanism displayed above are just examples and SHOULD NOT be considered as exhaustive list of solutions. Litkowski, et al. Expires September 4, 2016 [Page 15] Internet-Draft l3vpn-svc-cfg March 2016 5.1.1.2. Any to any +------------------------------------------------------------+ | VPN1_Site1 ------ PE1 PE2 ------ VPN1_Site2 | | | | VPN1_Site3 ------ PE3 PE4 ------ VPN1_Site4 | +------------------------------------------------------------+ Figure - Any to any VPN topology In the any to any topology, all VPN sites can discuss between each other without any restriction. It is expected that the management system that owns a any to any IPVPN service request through this model, needs to assign and then configure the VRF and route-targets on the appropriate PEs. In case of any to any, in general a single route-target is required and every VRF imports and exports this route-target. 5.1.1.3. Hub and Spoke +-------------------------------------------------------------+ | Hub_Site1 ------ PE1 PE2 ------ Spoke_Site1 | | +----------------------------------+ | | | +----------------------------------+ | Hub_Site2 ------ PE3 PE4 ------ Spoke_Site2 | +-------------------------------------------------------------+ Figure - Hub and Spoke VPN topology In the hub and spoke topology, all spoke sites can discuss only with Hub sites but not between each other. Hubs can discuss also between each other. It is expected that the management system that owns a any to any IPVPN service request through this model, needs to assign and then configure the VRF and route-targets on the appropriate PEs. In case of hub and spoke, in general a two route-targets are required (one route-target for Hub routes, one route-target for spoke routes). A Hub VRF, connecting Hub sites, will export Hub routes with Hub route-target, and will import Spoke routes through Spoke route- target. It will also import the Hub route-target to allow Hub to Hub communication. A Spoke VRF, connecting Spoke sites, will export Spoke routes with Spoke route-target, and will import Hub routes through Hub route-target. The management system MUST take into account Hub and Spoke connections constraints. For example, if management system decides to mesh a spoke site and a hub site on the same PE, it needs to mesh connections in different VRFs as displayed in the figure below. Litkowski, et al. Expires September 4, 2016 [Page 16] Internet-Draft l3vpn-svc-cfg March 2016 Hub_Site ------- (VRF_Hub) PE1 (VRF_Spoke) / | Spoke_Site1 -------------------+ | | Spoke_Site2 -----------------------+ 5.1.1.4. Hub and Spoke disjoint +-------------------------------------------------------------+ | Hub_Site1 ------ PE1 PE2 ------ Spoke_Site1 | +--------------------------+ +-------------------------------+ | | +--------------------------+ +-------------------------------+ | Hub_Site2 ------ PE3 PE4 ------ Spoke_Site2 | +-------------------------------------------------------------+ Figure - Hub and Spoke disjoint VPN topology In the hub and spoke disjoint topology, all spoke sites can discuss only with Hub sites but not between each other. Hubs cannot discuss between each other. It is expected that the management system that owns a any to any IPVPN service request through this model, needs to assign and then configure the VRF and route-targets on the appropriate PEs. In case of hub and spoke, in general a two route- targets are required (one route-target for Hub routes, one route- target for spoke routes). A Hub VRF, connecting Hub sites, will export Hub routes with Hub route-target, and will import Spoke routes through Spoke route-target. A Spoke VRF, connecting Spoke sites, will export Spoke routes with Spoke route-target, and will import Hub routes through Hub route-target. The management system MUST take into account Hub and Spoke connections constraints as in the previous case. 5.1.2. Cloud access The proposed model provides cloud access configuration through the cloud-access container. Internet access can typically be considered as a public cloud access service. The cloud-access container provides parameters for network address translation and authorization rules. A cloud identifier is used to reference the target service. This identifier is local to each administration. If NAT is required to access to the cloud, the nat-enabled leaf MUST be set to true. A NAT address may be provided in customer-nat- Litkowski, et al. Expires September 4, 2016 [Page 17] Internet-Draft l3vpn-svc-cfg March 2016 address, in case the customer is providing the public IP address for the cloud access. If service provider is providing the NAT address, customer-nat-address is not necessary as it can be picked from a service provider pool. By default, all sites in the IPVPN MUST be authorized to access to the cloud. In case restrictions are required, a user MAY configure the authorized-sites and denied-sites list. The authorization-sites defines the list of sites authorized for cloud access. The denied- sites defines the list of sites denied for cloud access. The model supports both "deny all expect" and "accept all expect" authorization. The "deny all expect" behavior is obtained by filling only the authorized-sites. All the sites listed will be authorized, all others will be denied. The "accept all expect" behavior is obtained by filling only the denied-sites. All the sites listed will be denied, all others will be authorized. Defining both denied-sites and authorized-sites MUST be processed as "deny all expect", so the denied-sites will have not effect. How the restrictions will be configured on network elements is out of scope of this document and will be specific to each deployment. IPVPN ++++++++++++++++++++++++++++++++ +++++++++++ + Site 3 + --- + Cloud1 + + Site 1 + +++++++++++ + + + Site 2 + --- ++++++++++++ + + + Internet + + Site 4 + ++++++++++++ ++++++++++++++++++++++++++++++++ | ++++++++++ + Cloud2 + ++++++++++ In the example above, we may configure the global VPN to access Internet by creating a cloud-access pointing to the cloud identifier for Internet service. No authorized-sites will be configured as all sites are required to access to Internet. NAT-enabled will be set to true and a nat-address will be configured. Litkowski, et al. Expires September 4, 2016 [Page 18] Internet-Draft l3vpn-svc-cfg March 2016 ZKITYHJ054687 CUSTOMER_1 any-to-any 51 true If Site1 and Site2 requires access to Cloud1, a new cloud-access will be created pointing to the cloud identifier of Cloud1. Authorized sites will be filled with reference to Site1 and Site2. 12456487 CUSTOMER_1 any-to-any 1111111 site1 site2 If all sites except Site1 requires access to Cloud2, a new cloud- access will be created pointing to the cloud identifier of Cloud2. denied-sites will be filled with reference to Site1. 12456487 CUSTOMER_1 any-to-any 22222222 site1 5.1.3. Multicast service Multicast in IP VPN is described in [RFC6513]. Litkowski, et al. Expires September 4, 2016 [Page 19] Internet-Draft l3vpn-svc-cfg March 2016 If IPVPN supports multicast service, it is expected to provide inputs on global multicast parameters. The user of this model will need to fill the flavor of trees that will be used by customer within the IPVPN (Customer tree). The proposed model supports ASM, SSM and BiDirectional trees (and can be augmented). Multiple flavors of tree can be supported simultaneously. (SSM tree) Recv (IGMPv3) -- Site2 ------- PE2 PE1 --- Site1 --- Source1 \ -- Source2 (ASM tree) Recv (IGMPv2) -- Site3 ------- PE3 (SSM tree) Recv (IGMPv3) -- Site4 ------- PE4 / Recv (IGMPv2) -- Site5 -------- (ASM tree) In case of ASM flavor, this model requires to fill the rp and rp- discovery parameters. Multiple RP to group mappings can be created. The RP service can be managed by the service provider using the leaf provider-managed/enabled set to true. In case of provider managed RP, anycast RP can also be activated providing redundancy as well as more optimal forwarding. In case of customer managed RP, the RP address must be filled in the RP to group mappings. The rp-discovery supports the auto-rp, static-rp, anycast-rp and bsr- rp modes. 5.1.4. Extranet VPNs There are some cases where a particular VPN needs to access to resources that are external. The resources may be located in another VPN. Litkowski, et al. Expires September 4, 2016 [Page 20] Internet-Draft l3vpn-svc-cfg March 2016 +-----------+ +-----------+ / \ / \ SiteA -- | VPN A | --- | VPN B | --- SiteB \ / \ / (Shared +-----------+ +-----------+ resources) In the figure above, VPN B has some resources on Site B that need to be available to some customers/partners. VPN A must be able to those VPN B resources. Such VPN connection scenario can be achieved by the VPN policy defined in Section 5.2.2.2. But there are some simple cases, where a particular VPN (VPN A) needs to access to all resources in a VPN B. The model provides an easy way to setup this connection using the extranet-vpns container. The extranet-vpns container defines a list of VPNs, a particular VPN wants to access. The extranet-vpns must be used on "customer" VPNs accessing extranet resources in another VPN. In the figure above, in order to give access for VPN A to VPN B, extranet-vpns container will be configured with an entry corresponding to VPN B. An implementation MUST consider the relation as bi-directional : if A requires access to B, the derived device configuration must let B be aware of A. The site-role leaf defines the role of the local VPN sites in the target extranet VPN topology. Site roles are defined in Section 5.2.1. In the example below, VPN A accesses to VPN B resources through extranet connection, a spoke role is required for VPN A sites, so sites from VPN A must not be able to communicate between each other through the extranet VPN connection. Litkowski, et al. Expires September 4, 2016 [Page 21] Internet-Draft l3vpn-svc-cfg March 2016 VPNB hub-spoke VPNA any-to-any VPNB spoke-role This model does not define how the extranet configuration will be achieved. Any more complex VPN connection topology (e.g. only part of sites of VPN A accessing only part of sites of VPN B) needs to be achieved using the vpn-policy defined in Section 5.2.2.2. 5.2. Site overview A site represents a connection of a customer location to one or more VPN services. +-------------+ / \ +------------------+ +-----| VPN1 | | | | \ / | New York Office | ----- (site) -----+ +-------------+ | | | +-------------+ +------------------+ | / \ +-----| VPN2 | \ / +-------------+ A site is composed of some characteristics : o Unique identifier (site-id) : to uniquely identify the site within the overall network infrastructure. The identifier is a string allowing to any encoding for the local administration of the VPN service. o Location (location) : site location informations to allow easy retrieval on nearest available resources. Litkowski, et al. Expires September 4, 2016 [Page 22] Internet-Draft l3vpn-svc-cfg March 2016 o Site constraints (site-diversity) : site-diversity container allow to define some constraints for the setup of the site, for example : PE disjointness or PoP disjointness. A site-group identifier allow to manage the disjointness. Two sites with the same group and requiring PE disjointness cannot be connected on the same PE. o Management (management) : defines the model of management of the site, for example : co-managed, customer managed or provider managed. o Site network accesses (site-network-accesses) : defines the list of network accesses associated to the sites and their properties : especially bearer, connection and service parameters. A site-network-access represents an IP logical connection of a site. A site may have multiple site-network-accesses. +------------------+ Site | |----------------------------------- | |****** (site-network-access#1) ****** | New York Office | | |****** (site-network-access#2) ****** | |----------------------------------- +------------------+ Multiple site-network-accesses are used in case of multihoming. The site configuration is viewed as a global entity, we assume that it is mostly the role of the management to split the parameters between the different elements within the network. For example, in the case of the site-network-access configuration, the management system needs to split the overall parameters between PE configuration and CE configuration. 5.2.1. Site role A VPN has a particular topology as described in Section 5.1.1. As a consequence, each site belonging to a VPN as a particular role in this topology. The site-role defines the role of the site in a particular VPN topology. In the any-to-any topology, all sites MUST have the same role which is any-to-any-role. In the hub-spoke or hub-spoke-disjoint topology, sites MUST have a hub-role or a spoke-role. Litkowski, et al. Expires September 4, 2016 [Page 23] Internet-Draft l3vpn-svc-cfg March 2016 5.2.2. Site belonging to multiple VPNs 5.2.2.1. Site vpn flavor A site may be part of one or multiple VPNs. The site flavor defines the way the VPN multiplexing is done. The current version of the model only supports two flavors : o site-vpn-flavor-single : the site belongs to only one VPN. o site-vpn-flavor-multi : the site belongs to multiple VPNs and all the logical accesses of the sites belongs to the same set of VPNs. 5.2.2.1.1. Single VPN attachment : site-vpn-flavor-single The figure below describes the single VPN attachment. The site connects to only one VPN. +--------+ +------------------+ Site / \ | |-----------------------------| | | |***(site-network-access#1)***| VPN1 | | New York Office | | | | |***(site-network-access#2)***| | | |-----------------------------| | +------------------+ \ / +--------+ 5.2.2.1.2. Multi VPN attachment : site-vpn-flavor-multi The figure below describes the multi VPN attachment. The site connects to multiple VPNs. +---------+ +---/----+ \ +------------------+ Site / | \ | | |--------------------------------- | |VPNB | | |***(site-network-access#1)******* | | | | New York Office | | | | | | |***(site-network-access#2)******* \ | / | |-----------------------------| VPNA +-----|---+ +------------------+ \ / +--------+ Litkowski, et al. Expires September 4, 2016 [Page 24] Internet-Draft l3vpn-svc-cfg March 2016 5.2.2.2. VPN policy The VPN policy defines the route exchange between multiple VPNs. A vpn-policy configuration MUST be configured to attach a site to one or multiple VPNs. The vpn-policy container defines relations of the site (or specific LAN of the sites) with VPNs. When vpn-policy is defined, the management system will built the route-target policy configuration from a combination of both the vpn-policy and the vpn- topology of the VPNs listed in the policy. As a site can belong to multiple VPNs, the vpn-policy may be composed of multiple entries. A filter can be applied to specify that only some LANs of the site should be part of a particular VPN. Each time a site (or LAN) is attached to a VPN, we must precise its role (site- role) within the targeted VPN topology. +--------------------------------------------------------------+ | VPN1_Site1 ------ PE1 PE2 ------ VPN1_Site2 | +--------------------------------------------------------------+ +--------------------------------------------------------------+ | VPN2_Site3 ------ PE7 | +-------------------------+ | | | +-------------------------+ | | VPN2_Site1 ------ PE3 PE4 ------ VPN2_Site2 | +----------------------------------+ | | | +------------------------------------------------------------+ | | VPN3_Site1 ------ PE5 | PE6 ------ VPN3_Site2 | | +------------------------------------------------------------+ | | | +---------------------------+ Let us consider service VPN1 with a any-to-any topology. For site#1, we define a VPN policy that attach the site to the VPN1 and setting the role of the site as "any-to-any-role". 1 VPN1 any-to-any-role Litkowski, et al. Expires September 4, 2016 [Page 25] Internet-Draft l3vpn-svc-cfg March 2016 Now let us consider service VPN2 with a hub and spoke disjoint topology (Site1, Site3 are Hubs). For site#1, we define a VPN policy that attach the site to the VPN2 and setting the role of the site as "hub-role". 1 VPN2 hub-role When the vpn services are provisioned a route-target value will be affected by the OSS of the service provider for these VPNs. Let's call RT1 the route-target of VPN1,and RT21(spoke)/RT22(hub) the route-target of VPN2. Now we consider a new VPN service VPN3 (any to any) that must be provisioned, RT3 will be allocated by the OSS for proper configuration on network elements. Consider a site#1 in VPN3 that must communicate only in VPN3, in this case, the vpn-policy will be similar to Site#1 of VPN1. The VRF on PE5 for VPN3 will be so provisioned by the management system using RT3 value as import and export value. Consider a site#2 in VPN3 that must communicate in VPN3, and a specific LAN LAN1 must communicate with VPN2 as a spoke (as VPN2 is hub and Spoke disjoint). Below is a sample configuration of the VPN policy for site#2 : Litkowski, et al. Expires September 4, 2016 [Page 26] Internet-Draft l3vpn-svc-cfg March 2016 1 LAN1 VPN2 spoke-role 2 VPN3 any-to-any-role The VRF on PE6 for VPN3 will be so provisioned by the management system using RT3 value as import and RT3 as export value plus RT21 for LAN1 prefix. 5.2.3. Security Security container defines customer specific security parameters for the site. This section will more be detailed in future revision. 5.2.3.1. Encryption Encryption can be requested on the connection. It may be performed at layer 2 or layer 3 by selecting the appropriate enumeration in "layer" leaf. The encryption profile can be a service provider defined template or customer specific. 5.2.4. Management The model proposes three types of common management options : o comanaged : the CE router is managed by the provider and also by the customer. o provider-managed : the CE router is managed only by the provider. o customer-managed : the CE router is managed only by the customer. Litkowski, et al. Expires September 4, 2016 [Page 27] Internet-Draft l3vpn-svc-cfg March 2016 Based on the management model, different security options MAY be derived. In case of "provider-managed" or "comanaged", the model proposes some option to define the management transport protocol (IPv4 or IPv6) and the associated management address. 5.2.5. Routing protocols Routing-protocol defines which routing protocol must be activated between the provider and the customer router. The current model support : bgp, rip, rip-ng, ospf, static, direct, vrrp. The routing protocol defined applies at the provider to customer boundary. Depending of the management of the management model, it may apply to the PE-CE boundary or CE to customer boundary. In case of customer managed site, the routing-protocol defined will be activated between the PE and the CE router managed by the customer. In case of provider managed site, the routing-protocol defined will be activated between the CE managed by the SP and the router or LAN belonging to the customer. In this case, it is expected that the PE- CE routing will be configured based on the service provider rules as both are managed by the same entity. Rtg protocol 192.0.2.0/24 ----- CE ----------------- PE1 Customer managed site Rtg protocol Customer router ------------- CE ----------------- PE1 Provider managed site All the examples below will refer to a customer managed site case. 5.2.5.1. Dual stack handling All routing protocol types support dual stack by using address-family leaf-list. Litkowski, et al. Expires September 4, 2016 [Page 28] Internet-Draft l3vpn-svc-cfg March 2016 Example of Dual stack using the same routing protocol : static ipv4-unicast ipv6-unicast Example of Dual stack using two different routing protocols : rip ipv4-unicast ospf ipv6-unicast 5.2.5.2. Direct LAN connection onto SP network Routing-protocol "direct" SHOULD be used when a customer LAN is directly connected to the provider network and must be advertised in the IPVPN. LAN attached directly to provider network : 192.0.2.0/24 ----- PE1 5.2.5.3. Direct LAN connection onto SP network with redundancy Routing-protocol "vrrp" SHOULD be used when a customer LAN is directly connected to the provider network and must be advertised in the IPVPN and LAN redundancy is expected. Litkowski, et al. Expires September 4, 2016 [Page 29] Internet-Draft l3vpn-svc-cfg March 2016 LAN attached directly to provider network with LAN redundancy: 192.0.2.0/24 ------ PE1 | +-- PE2 5.2.5.4. Static routing Routing-protocol "static" MAY be used when a customer LAN is connected to the provider network through a CE router and must be advertised in the IPVPN. Static rtg 192.0.2.0/24 ------ CE -------------- PE | | | Static route 192.0.2.0/24 Static route 0.0.0.0/0 nh CE nh PE 5.2.5.5. RIP routing Routing-protocol "rip" MAY be used when a customer LAN is connected to the provider network through a CE router and must be advertised in the IPVPN. In case of dual stack, the management system will be responsible to configure rip (including right version number) and rip-ng instances on network elements. RIP rtg 192.0.2.0/24 ------ CE -------------- PE 5.2.5.6. OSPF routing Routing-protocol "ospf" MAY be used when a customer LAN is connected to the provider network through a CE router and must be advertised in the IPVPN. It can be used to extend an existing OSPF network and interconnect different areas. See [RFC4577] for more details. Litkowski, et al. Expires September 4, 2016 [Page 30] Internet-Draft l3vpn-svc-cfg March 2016 +---------------------+ | | OSPF | | OSPF area 1 | | area 2 (OSPF | | (OSPF area 1) --- CE ---------- PE PE ----- CE --- area 2) | | +---------------------+ The model also proposes an option to create an OSPF sham-link between two sites sharing the same area and having a backdoor link. The sham-link is created by referencing the target site sharing the same OSPF area. The management system will be responsible to check if there is already a shamlink configured for this VPN and area between the same pair of PEs. If there is no existing shamlink, the management system will provision it, this shamlink MAY be reused by other sites. +------------------------+ | | | | | PE (--shamlink--)PE | | | | | +----|----------------|--+ | OSPF area1 | OSPF area 1 | | CE1 CE2 | | (OSPF area1) (OSPF area1) | | +----------------+ Regarding Dual stack support, user MAY decide to fill both IPv4 and IPv6 address families, if both protocols SHOULD be routed through OSPF. As OSPF is using two different protocol for IPv4 and IPv6, the management system will need to configure both ospf version 2 and version 3 on the PE-CE link. Example of OSPF routing parameters in service model. Litkowski, et al. Expires September 4, 2016 [Page 31] Internet-Draft l3vpn-svc-cfg March 2016 ospf 0.0.0.1 ipv4-unicast ipv6-unicast Example of PE configuration done by management system : router ospf 10 area 0.0.0.1 interface Ethernet0/0 ! router ospfv3 10 area 0.0.0.1 interface Ethernet0/0 ! 5.2.5.7. BGP routing Routing-protocol "bgp" MAY be used when a customer LAN is connected to the provider network through a CE router and must be advertised in the IPVPN. BGP rtg 192.0.2.0/24 ------ CE -------------- PE The AS numbers, peerings addressing will be derived from connection parameters or customer-specific-information as well as internal knowledge of SP. In case of dual stack access, user MAY request BGP routing for both IPv4 and IPv6 by filling both address-families. It will be up to SP and management system to decide how to decline the configuration (two BGP sessions, single, multisession ...). The service configuration below actives BGP on PE-CE link for both IPv4 and IPv6. Litkowski, et al. Expires September 4, 2016 [Page 32] Internet-Draft l3vpn-svc-cfg March 2016 bgp 65000 ipv4-unicast ipv6-unicast This service configuration can be derived by management system into multiple flavors depending on SP flavor. Example #1 of PE configuration done by management system (single session IPv4 transport): router bgp 100 neighbor 203.0.113.2 remote-as 65000 address-family ipv4 vrf Cust1 neighbor 203.0.113.2 activate address-family ipv6 vrf Cust1 neighbor 203.0.113.2 activate neighbor 203.0.113.2 route-map SET-NH-IPV6 out Example #2 of PE configuration done by management system (two sessions): router bgp 100 neighbor 203.0.113.2 remote-as 65000 neighbor 2001::2 remote-as 65000 address-family ipv4 vrf Cust1 neighbor 203.0.113.2 activate address-family ipv6 vrf Cust1 neighbor 2001::2 activate Example #3 of PE configuration done by management system (multisession): router bgp 100 neighbor 203.0.113.2 remote-as 65000 neighbor 203.0.113.2 multisession per-af address-family ipv4 vrf Cust1 neighbor 203.0.113.2 activate address-family ipv6 vrf Cust1 neighbor 203.0.113.2 activate neighbor 203.0.113.2 route-map SET-NH-IPV6 out Litkowski, et al. Expires September 4, 2016 [Page 33] Internet-Draft l3vpn-svc-cfg March 2016 5.2.6. Service The service defines service parameters associated with the site. 5.2.6.1. QoS The model proposes to define QoS parameters in an abstracted way : o qos-classification-policy : define a set of ordered rules to classify customer traffic. o qos-profile : outgoing QoS profile to be applied. 5.2.6.1.1. QoS classification QoS classification rules are handled by qos-classification-policy. The qos-classification-policy is an ordered list of rules that match a flow and set the appropriate target class of service (target-class- id). The match criterion provide a basic infrastructure for defining flows : layer 3 source and destination address, layer 4 ports, layer 4 protocol. Where the classification is done depends on the SP implementation of the service, but classification concerns the flow coming from the customer site and entering the network. Provider network +-----------------------+ 192.0.2.0/24 198.51.100.0/24 ---- CE --------- PE Traffic flow ----------> In the figure above, the management system can decide : o if the CE is customer managed, to implement the classification rule in the ingress direction on the PE interface. o if the CE is provider managed, to implement the classification rule in the ingress direction on the CE interface connected to customer LAN. The figure below describes a sample service description of qos- classification for a site : Litkowski, et al. Expires September 4, 2016 [Page 34] Internet-Draft l3vpn-svc-cfg March 2016 1 192.0.2.0/24 203.0.113.1/32 80 tcp DATA2 2 192.0.2.0/24 203.0.113.1/32 21 tcp DATA2 3 DATA1 In the example above : o HTTP traffic from 192.0.2.0/24 LAN destinated to 203.0.113.1/32 will be classified in DATA2. o FTP traffic from 192.0.2.0/24 LAN destinated to 203.0.113.1/32 will be classified in DATA2. o All other traffic will be classified in DATA1. The order of rules is really important. The management system responsible for translating those rules in network element configuration MUST keep the same processing order in element configuration. The order of rule is defined by the "id" leaf. The lowest "id" MUST be processed first. Litkowski, et al. Expires September 4, 2016 [Page 35] Internet-Draft l3vpn-svc-cfg March 2016 5.2.6.1.2. QoS profile User can choose between standard profile provided by the operator or custom profile. Provider network +-----------------------+ 192.0.2.0/24 198.51.100.0/24 ---- CE --------- PE \ / qos-profile A custom qos-profile is defined as a list of class of services and associated properties. The properties are : o rate-limit : used to rate-limit the class of service. The value is expressed as a percentage of the global service bandwidth. o priority-level : used to define priorities between class of services. The value of the priority to be used is dependant of each administration. The higher the priority-level is, the higher the priority of the class will be. Priority-level is used to define strict priority queueing. A priority-level 250 class will be served before a priority-level 100 class until there is no more packet to process or until rate-limit does not allow anymore packets from the higher priority class. o guaranteed-bw-percent : used to define a guaranteed amount of bandwidth for the class of service. It is expressed as a percentage. The guaranteed-bw-percent uses available bandwidth at the priority-level of the class. Example of service configuration using a standard qos profile : Litkowski, et al. Expires September 4, 2016 [Page 36] Internet-Draft l3vpn-svc-cfg March 2016 1245HRTFGJGJ154654 100000000 100000000 PLATINUM 555555AAAA2344 2000000 2000000 GOLD Example of service configuration using a custom qos profile : Site1 100000000 100000000 REAL_TIME 10 10 DATA 5 Litkowski, et al. Expires September 4, 2016 [Page 37] Internet-Draft l3vpn-svc-cfg March 2016 Site2 2000000 2000000 REAL_TIME 30 10 DATA1 5 80 DATA2 5 20 The custom qos-profile for site1 defines that traffic from REAL_TIME class will have a higher priority than traffic from DATA class. The REAL_TIME traffic will be rate-limit to 10% of the service bandwidth (10% of 100Mbps = 10Mbps) to let some place for DATA traffic. The custom qos-profile for site2 defines that traffic from REAL_TIME class will have a higher priority than traffic from data traffic. Data traffic will be splitted in two class of service DATA1 and DATA2 that will share bandwidth between them according to the percentage of guaranteed-bw-percent. The maximum of percentage to be used is not limited by this model but MUST be limited by the management system according to the policies authorized by the service provider. The REAL_TIME traffic will be rate-limit to 30% of the service bandwidth (30% of 100Mbps = 30Mbps) to let some place for data traffic. In case of congestion of the access, the REAL_TIME traffic can go up to 30Mbps (Let's assume that 20Mbps only are consumed). The DATA1 and Litkowski, et al. Expires September 4, 2016 [Page 38] Internet-Draft l3vpn-svc-cfg March 2016 DATA2 will share remaining bandwidth (80Mbps) according to their percentage. So DATA1 will be served with at least 64Mbps of bandwidth. 5.2.6.2. Multicast The multicast section defines the type of site in the customer multicast topology : source, receiver, or both. These parameters will help management system to optimize the multicast service. User can also define the type of multicast relation with the customer : router (requires a protocol like PIM), host (IGMP or MLD), or both. Transport protocol (IPv4 or IPv6 or both) can also be defined. 5.2.7. Site network accesses As mentioned, a site may be multihomed. Each network access for a site is defined in the site-network-accesses list. The site-network- access defines how the service is connected on the network and is splitted in three main classes of parameters : o bearer : defines physical parameters of the attachment. o connection : defines protocol parameters of the attachment (transport layer and routing protocols). o availability : defines the site availability policy. Availability is defined in Section 5.2.8.3 Some parameters from the site can be configured also at the access level like : routing, services, security ... Defining parameters only at site level will provide inheritance. If a parameter is configured at both site and access level, the access level parameter MUST override the site level parameter. 5.2.7.1. Bearer Bearer defines an internal reference to the bearer used for the access. Two strings are available (type and bearer-reference) to encode necessary informations to map the VPN access to the appropriate network access bearer. How the mapping is done is out of scope of the document. 5.2.7.2. Connection The connection defines the protocol parameters of the attachment (IPv4 and IPv6). Depending of the management mode, it refers to the PE-CE addressing or CE to customer LAN addressing. In any case, it Litkowski, et al. Expires September 4, 2016 [Page 39] Internet-Draft l3vpn-svc-cfg March 2016 describes the provider to customer responsibility boundary. For a customer managed site, it refers to the PE-CE connection. For a provider managed site, it refers to the CE to LAN connection. 5.2.7.2.1. IP addressing IP subnet can be configured for either transport protocols. For a dual stack connection, two subnets will be provided, one for each transport layer. The address-allocation-type will help in defining how the address allocation MUST be done. The current model proposes three ways of IP address allocation : o provider-dhcp : the provider will provide DHCP service for customer equipments, this is applicable to both IPv4 and IPv6 addressing. o static-address : Addresses will be assigned manually on both sides, this is applicable to both IPv4 and IPv6 addressing. o slaac : enables stateless address autoconfiguration ([RFC4862]). This is applicable only for IPv6. 5.2.8. Deciding where to connect the site The management system will have to decide where to connect the site in the provider network (PE, aggregation switch ...). This decision MAY be based on any constraint that are up to the service provider : least load, distance ... The current model proposes some parameters that will help the management system to decide where to attach the customer site. It would be up to the service provider to define which on those parameters are relevant for placing the site, moreover the service provider can decide to rely also on other internal parameters. 5.2.8.1. Site location The location information provided in this model MAY be used by a management system to decide the target PE to mesh the site. Litkowski, et al. Expires September 4, 2016 [Page 40] Internet-Draft l3vpn-svc-cfg March 2016 PoP#1 (New York) +---------+ | PE1 | Site #1 ---... | PE2 | (Atlantic City) | PE3 | +---------+ PoP#2 (Washington) +---------+ | PE4 | | PE5 | | PE6 | +---------+ PoP#3 (Philadelphia) +---------+ | PE7 | Site #2 ---... | PE2 | (Reston) | PE9 | +---------+ In the example below, the management system may decide to mesh Site #1 on a PE from Philadelphia PoP for distance reason. It may also take in account resources available on PEs to decide the exact target PE (least load). In case of shortest distance PE used, it may also decide to mesh Site #2 on Washington PoP. 5.2.8.2. Site diversity The site diversity defines what is the acceptable fate sharing level in case multiple sites for a single VPN must be provisioned in a common location. The site diversity introduces the notion of site- group. Sites belonging to the same site-group cannot share the same fate. We propose to introduce two constraints : PoP diverse : site belonging to the same site-group MUST be provisioned on different PoPs. PE diverse : site belonging to the same site-group MUST be provisioned on different PE routers. How these diversity constraints are applied is out of scope of the document. As an example, the management system receiving the request for diversity, MAY exchange information with some OSS components to define the best target PEs based on location and resource availability. Litkowski, et al. Expires September 4, 2016 [Page 41] Internet-Draft l3vpn-svc-cfg March 2016 As example, if a company has multiple small branch offices (single homed) that requires to be connected in the same location, it is desirable to dispatch the attachment on multiple PEs. So in case of PE crash, only some offices will be impacted. PoP#1 +---------+ | PE1 | Office#1 ---... | PE2 | Office#2 ---... | PE3 | Office#3 ---... | PE4 | Office#...--... +---------+ Office#100--... In the figure above, it may be good to mesh 25 offices on each PE of PoP#1 to prevent concentration of two many customer offices on common network elements. 5.2.8.3. Site network access availability A site may be multihomed, so having multiple site-network-accesses. An implementation MAY apply placement diversity for accesses belonging to the same site. By default, diversity for accesses belonging to the same site is set to "PE-diverse". Consider a dual homed hub site, it is desirable for redundancy to provision the two VPN access connections on two different PEs or two different PoPs. PoP#1 +---------+ | PE1 | Hub_Site_primary ------ | PE2 | | PE3 | +---------+ PoP#2 +---------+ | PE4 | Hub_Site_backup ------- | PE5 | | PE6 | +---------+ In a PoP diverse scenario, the management system may decide to mesh Hub_Site_primary on any PE of PoP#1 and Hub_Site_backup on any PE of PoP#2. In a PE diverse scenario, if the management system decides to Litkowski, et al. Expires September 4, 2016 [Page 42] Internet-Draft l3vpn-svc-cfg March 2016 mesh Hub_Site_primary on PE1, it is require to mesh Hub_Site_backup on any PE different from PE1. The site-network-access/availability defines parameters for the site redundancy. The access-priority defines a preference for a particular access. This preference is used to model any kind of loadbalancing or primary/backup scenario. The highest the access- priority is, and the highest the preference will be. The figure below describes how access-priority attribute can be used. Hub#1 LAN (Primary/backup) Hub#2 LAN (Loadsharing) | | | access-priority 1 access-priority 1 | |--- CE1 ------- PE1 PE3 --------- CE3 --- | | | | | |--- CE2 ------- PE2 PE4 --------- CE4 --- | | access-priority 2 access-priority 1 | PE5 | | | CE5 | Spoke#1 site (Single-homed) In the figure above, Hub#2 requires loadsharing so all the site- network-accesses must use the same access-priority value. At the contrary, as Hub#1 requires primary/backup, a higher access-priority will be configured on the primary access. More complex scenario can be modeled. Let's consider a Hub site with 5 accesses to the network (A1,A2,A3,A4,A5). The customer wants to loadshare traffic on A1,A2 in the nominal situation. If A1 and A2 fails, he wants to loadshare traffic on A3 and A4, and finally if A1 to A4 are down, he wants to use A5. We can model it easily by associating the following access-priorities : A1=100, A2=100, A3=50, A4=50, A5=10. 5.2.8.3.1. Traffic protection The service model supports the ability to protect traffic for the site. Protection provides a better availability to multihoming by using local-repair techniques in case of failures. Litkowski, et al. Expires September 4, 2016 [Page 43] Internet-Draft l3vpn-svc-cfg March 2016 Site#1 Site#2 CE1 ----- PE1 -- P1 P3 -- PE3 ---- CE3 | | | | | | CE2 ----- PE2 -- P2 P4 -- PE4 ---- CE4 / / CE5 ----+ Site#3 In the figure above, we consider an IPVPN service with three sites including two dual homed sites (site#1 and #2). For dual homed sites, we consider PE1-CE1 and PE3-CE3 as primary, and PE2-CE2,PE4-CE4 as backup for the example (even if protection also applies to loadsharing scenarios.) In order to protect Site#2 against a failure, user may set the enabled leaf of traffic-protection to true on the site-network- accesses of site#2. How the traffic protection will be implemented is out of scope of the document. But as an example, in such case, if we consider traffic coming from a remote site (site#1 or site#3), primary path is to use PE3 as egress PE. PE3 may have preprogrammed a backup forwarding entry pointing to backup path (through PE4-CE4) for all prefixes going through PE3-CE3 link. How backup path is computed is out of scope of the document. When PE3-CE3 link fails, traffic is still received by PE3 but PE3 switch automatically traffic to the backup entry, path will so be PE1-P1-(...)-P3-PE3-PE4-CE4 until remote PEs reconverge and use PE4 as egress PE. 5.2.8.4. Route Distinguisher and VRF allocation Route distinguisher is also a critical parameter of PE-based L3VPN as described in [RFC4364] that will allow to distinguish common addressing plans in different VPNs. As for Route-targets, it is expected management system to allocate a VRF on the target PE and a route-distinguisher for this VRF. If a VRF exists on the target PE, and the VRF fulfils the connectivity constraints for the site, there is no need to recreate another VRF and the site MAY be meshed within this existing VRF. How the management system checks that an existing VRF fulfils the connectivity constraints for a site is out of scope of this document. If no VRF exists on the target PE, filling the site constraints, the management system will have to initiate a new VRF creation on the target PE and will have to allocate a new route distinguisher for this new VRF. Litkowski, et al. Expires September 4, 2016 [Page 44] Internet-Draft l3vpn-svc-cfg March 2016 The management system MAY apply a per-VPN or per-VRF allocation policy for the route-distinguisher depending of the service provider policy. In a per-VPN allocation policy, all VRFs (dispatched on multiple PEs) within a VPN will share the same route distinguisher value. In a per-VRF model, all VRFs will always have a unique route- distinguisher value. Some other allocation policies are also possible, and this document does not restrict the allocation policies to be used. Allocation of route-distinguisher MAY be done in the same way as the route-targets. The example provided in Section 5.1.1.1 could be reused. Note that a service provider MAY decide to configure target PE for automated allocation of route distinguisher. In this case, there will be no need for any backend system to allocate a route- distinguisher value. 5.3. Enhanced VPN features 5.3.1. Carrier Supporting Carrier In case of Carrier Supporting Carrier (CsC), a customer MAY want to build MPLS service using an IPVPN as transport layer. Litkowski, et al. Expires September 4, 2016 [Page 45] Internet-Draft l3vpn-svc-cfg March 2016 LAN customer1 | | CE1 | | ------------- (vrf_cust1) CE1_ISP1 | ISP1 PoP | MPLS link | ------------- | (vrf ISP1) PE1 (...) Provider backbone PE2 (vrf ISP1) | | ------------ | | MPLS link | ISP1 PoP CE2_ISP1 (vrf_cust1) |------------- | CE2 | Lan customer1 In the figure above, ISP1 resells IPVPN service but has no transport infrastructure between its PoPs. ISP1 uses an IPVPN as transport infrastructure (belonging to another provider) between its PoPs. In order to support CsC, the VPN service must be declared MPLS support using the "mpls" leaf set to true in vpn-svc. The link between CE1_ISP1/PE1 and CE2_ISP1/PE2 must also run a MPLS signalling protocol. This configuration is done at the site level. In the proposed model, LDP or BGP can be used as MPLS signalling protocol. In case of LDP, an IGP routing protocol MUST also be Litkowski, et al. Expires September 4, 2016 [Page 46] Internet-Draft l3vpn-svc-cfg March 2016 activated. In case of BGP signalling, BGP MUST also be configured as routing-protocol. 5.3.2. Transport constraints A customer may require some constraints for transporting traffic between particular sites. As example, a customer may require low latencies and disjoint paths between two hub sites. The current model proposes to define a list of constraints that can be augmented for unicast and/or multicast traffic. For unicast traffic, the model considers that the constraints are bidirectional (same constraint from site1 to site2 and site2 to site1). For multicast, constraints are unidirectional from source to receiver. The current model supports the following constraints : o Latency : this constraint allow to create the lowest latency path possible or to create a path with a latency boundary. In case a latency boundary is required, the boundary MUST be encoded in the constraint-opaque-value using a millisecond unit. o Bandwidth : this constraint allow to create a path that fits specific bandwidth requirement. If no constraint-opaque-value is provided, an implementation SHOULD use the lowest bandwidth between the two sites as reference. If constraint-opaque-value is used, the required bandwidth MUST be encoded in Mbps, and the implementation MUST use this value as reference. o Jitter : this constraint allow to create a path with a jitter boundary. constraint-opaque-value MUST be used with jitter constraint and MUST contain the jitter boundary expressed in milliseconds. o Path diversity : this constraint allow creation of disjoint paths between two sites. This requires the sites to be multihomed. constraint-opaque-value is not used. o Site diversity : this constraint is similar to path diversity but ensures that paths are not crossing the same sites. This requires the sites to be multihomed. constraint-opaque-value MAY be used to encode additional site location that must be avoided. 5.4. Using configuration templates The proposed model supports the creation and application of configuration templates for sites. Litkowski, et al. Expires September 4, 2016 [Page 47] Internet-Draft l3vpn-svc-cfg March 2016 A template can be configured by creating adding a site in the site- template list. The "site-templates" list contains only templates. Real sites are part of the "sites" list. Multiple templates can be configured. Templates can be applied at multiple levels referenced by apply-template leaf. The apply- template references the site-id of the template to be called. The location of the apply-template within the sites hierarchy defines which parameters must be inherited. For example, if apply-template is done on service container of a site, only service container parameters (and childs) from the template will be applied. Litkowski, et al. Expires September 4, 2016 [Page 48] Internet-Draft l3vpn-svc-cfg March 2016 Template-VoiceCoS-Cust1 REAL_TIME 30 10 DATA1 5 80 DATA2 5 20 Template-VPNsite-Customer1 PLATINUM Site-templates allow to define configuration blocks that will be inherited by one or multiple sites in order to speed up configuration. For example, if all the sites of an IPVPN service have the almost same configuration (routing-protocol, qos, management ...), a template can be created and each site of the VPN will reference the template. If a site has some particular parameters, specific parameters within the site MUST always override parameters derived from template. Litkowski, et al. Expires September 4, 2016 [Page 49] Internet-Draft l3vpn-svc-cfg March 2016 The example above defines two site templates : o Template-VPNsite-Customer1 that will be used to configure all the VPN sites for customer 1. o Template-VoiceCoS-Cust1 that will be used to configure some special CoS policy on some specific accesses of the VPN. In the example below, all sites of VPN1 are inheriting basic configuration from template Template-VPNsite-Customer1. Some specific parameters like svc-input-bandwidth are also defined for each site. For Site 4 and 5 , specific QoS parameters are required, a new template Template-VoiceCoS-Cust1 is applied at service level for these two sites, overriding the service parameters from the Template-VPNsite-Customer1 template. Litkowski, et al. Expires September 4, 2016 [Page 50] Internet-Draft l3vpn-svc-cfg March 2016 Site1 Template-VPNsite-Customer1 5000000 5000000 Site2 Template-VPNsite-Customer1 20000000 20000000 Site3 Template-VPNsite-Customer1 30000000 30000000 Site4 Template-VPNsite-Customer1 Template-VoiceCoS-Cust1 100000000 100000000 Site5 Template-VPNsite-Customer1 Template-VoiceCoS-Cust1 450000000 450000000 Litkowski, et al. Expires September 4, 2016 [Page 51] Internet-Draft l3vpn-svc-cfg March 2016 6. Service model usage example As explained in Section 4, this service model is intended to be instantiated at a management layer and is not intended to be used directly on network elements. The management system serves as a central point of configuration of the overall service. This section provides an example on how a management system can use this model to configure an IPVPN service on network elements. The example wants to achieve the provisionning of a VPN service for 3 sites using hub and spoke topology. One of the site will be dual homed and loadsharing is expected. +-------------------------------------------------------------+ | Hub_Site ------ PE1 PE2 ------ Spoke_Site1 | | | +----------------------------------+ | | | | | +----------------------------------+ | Hub_Site ------ PE3 PE4 ------ Spoke_Site2 | +-------------------------------------------------------------+ The following XML describes the overall simplified service configuration of this VPN. 12456487 CUSTOMER1 hub-spoke When receiving the request for provisioning the VPN service, the management system will internally (or through discussion with other OSS component) allocates VPN route-targets. In this specific case two RTs will be allocated (100:1 for Hub and 100:2 for Spoke). The output below describes the configuration of Spoke1. Spoke_Site1 pe-diverse 100 NY US Litkowski, et al. Expires September 4, 2016 [Page 52] Internet-Draft l3vpn-svc-cfg March 2016 bgp 500 ipv4-unicast Spoke_Site1 203.0.113.254 203.0.113.2 24 provider-managed ipv4-unicast
192.0.2.1
450000000 450000000 1 VPN1 spoke-role
When receiving the request for provisioning Spoke1 site, the management system MUST allocate network resources for this site. It MUST first decide the target network elements to provision the access, and especially the PE router (and may be an aggregation switch). As described in Section 5.2.8, the management system SHOULD use the location information and SHOULD use the site-diversity constraint to find the appropriate PE. In this case, we consider Litkowski, et al. Expires September 4, 2016 [Page 53] Internet-Draft l3vpn-svc-cfg March 2016 Spoke1 requires PE diversity with Hub and that management system allocate PEs based on lowest distance. Based on the location information, the management system finds the available PEs in the nearest area of the customer and picks one that fits the site- diversity constraint. When the PE is chosen, management system needs to allocate interface resources on the node, one interface is so picked from the PE available pool. The management system can start provisioning the PE node by using any mean (Netconf, CLI, ...). The management system will check if a VRF is already present that fits the needs. If not, it will provision the VRF : Route distinguisher will come from internal allocation policy model, route-targets are coming from the vpn-policy configuration of the site (management system allocated some RTs for the VPN). As the site is a spoke site (site-role), the management system knows which RT must be imported and exported. As the site is provider managed, some management route-targets may also be added (100:5000). Standard provider VPN policies MAY also be added in the configuration. Example of generated PE configuration : ip vrf Customer1 export-map STD-CUSTOMER-EXPORT <---- Standard SP configuration route-distinguisher 100:3123234324 route-target import 100:1 route-target import 100:5000 <---- Standard SP configuration route-target export 100:2 for provider managed ! When the VRF has been provisioned, the management system can start configuring the access on the PE using the allocated interface information. IP addressing is derived from the subnet-prefix of the connection. One address will be picked from the subnet for the PE, another will be used for the CE configuration. Routing protocols will also be configured on the PE, bgp will be used as requested in the service model. Peering addresses will be derived from subnet- prefix. PE AS number is well known and as CE is provider managed, CE AS number can be automatically allocated by the management system. Some provider standard configuration templates may also be added. Litkowski, et al. Expires September 4, 2016 [Page 54] Internet-Draft l3vpn-svc-cfg March 2016 Example of generated PE configuration : interface Ethernet1/1/0.10 encapsulation dot1q 10 ip vrf forwarding Customer1 ip address 198.51.100.1 255.255.255.252 <---- Comes from automated allocation ip access-group STD-PROTECT-IN <---- Standard SP config ! router bgp 100 address-family ipv4 vrf Customer1 neighbor 198.51.100.1 remote-as 65000 <---- Comes from automated allocation neighbor 198.51.100.1 route-map STD in <---- Standard SP config neighbor 198.51.100.1 filter-list 10 in <---- Standard SP config ! ip route vrf Customer1 192.0.2.1 255.255.255.255 198.51.100.2 ! Static route for provider administration of CE ! As the CE router is not reachable at this stage, the management system can produce a complete CE configuration that can be uploaded to the node by manual operation before sending the CE to customer premise. The CE configuration will be built as for the PE. Based on the CE type (vendor/model) allocated to the customer and bearer information, the management system knows which interface must be configured on the CE. PE-CE link configuration is expected to be handled automatically using the service provider OSS as both resources are managed internally. CE to LAN interface parameters like IP addressing are derived from ip-connection taking into account how management system distributes addresses between PE and CE within the subnet. This will allow to produce a plug'n'play configuration for the CE. Litkowski, et al. Expires September 4, 2016 [Page 55] Internet-Draft l3vpn-svc-cfg March 2016 Example of generated CE configuration : interface Loopback10 description "Administration" ip address 192.0.2.1 255.255.255.255 ! interface FastEthernet10 description "WAN" ip address 198.51.100.2 255.255.255.252 <---- Comes from automated allocation ! interface FastEthernet11 description "LAN" ip address 203.0.113.254 255.255.255.0 <---- Comes from ip-connection ! router bgp 65000 redistribute static route-map STATIC2BGP <---- Standard SP configuration neighbor 198.51.100.1 remote-as 100 <---- Comes from automated allocation neighbor 203.0.113.2 remote-as 500 <---- Comes from ip-connection ! route-map STATIC2BGP permit 10 match tag 10 ! 7. Interaction with Other YANG Modules As expressed in Section 4, this service module is intended to be instantiated in management system and not directly on network elements. It will be the role of the management system to configure the network elements. The management system MAY be modular, so the component instantiating the service model (let's call it service component) and the component responsible for network element configuration (let's call it configuration component) MAY be different. Litkowski, et al. Expires September 4, 2016 [Page 56] Internet-Draft l3vpn-svc-cfg March 2016 L3VPN-SVC | service model | | +----------------------+ | Service component | service datastore +----------------------+ | | +----------------------+ +----| Config component |-------+ / +----------------------+ \ Network / / \ \ Configuration / / \ \ models / / \ \ +++++++ ++++++++ ++++++++ +++++++ + CEA + ------- + PE A + + PE B + ----- + CEB + Config +++++++ ++++++++ ++++++++ +++++++ datastore Site A Site B In the previous sections, we provided some example of translation of service provisioning request to router configuration lines as illustration. In the NetConf/Yang ecosystem, it will be expected NetConf/YANG to be used between configuration component and network elements to configure the requested service on these elements. In this framework, it is expected from standardization to also work on specific configuration YANG modelization of service components on network elements. There will be so a strong relation between the abstracted view provided by this service model and the detailed configuration view that will be provided by specific configuration models for network elements. Authors of this document are expecting definition of YANG models for network elements on this non exhaustive list of items : o VRF definition including VPN policy expression. o Physical interface. o IP layer (IPv4, IPv6). o QoS : classification, profiles... o Routing protocols : support of configuration of all protocols listed in the document, as well as routing policies associated with these protocols. Litkowski, et al. Expires September 4, 2016 [Page 57] Internet-Draft l3vpn-svc-cfg March 2016 o Multicast VPN. o Network Address Translation. o ... Example of VPN site request at service level using this model : Site A static-address 203.0.113.0/30 static 198.51.100.0/30 203.0.113.2 customer-managed>/type< 1 VPN1 any-to-any-role Litkowski, et al. Expires September 4, 2016 [Page 58] Internet-Draft l3vpn-svc-cfg March 2016 In the service example above, it is expected that the service component requests to the configuration component of the management system the configuration of the service elements. If we consider that service component selected a PE (PE A) as target PE for the site, the configuration component will need to push the configuration to PE A. The configuration component will use several YANG data models to define the configuration to be applied to PE A. The XML configuration of PE-A may look like this : eth0 ianaift:ethernetCsmacd Link to CEA. 203.0.113.1 30 true VRF_CustA l3vpn:vrf VRF for CustomerA 100:1546542343 100:1 100:1 eth0 rt:static st0 Litkowski, et al. Expires September 4, 2016 [Page 59] Internet-Draft l3vpn-svc-cfg March 2016 198.51.100.0/30 203.0.113.2 8. YANG Module file "ietf-l3vpn-svc@2016-03-03.yang" module ietf-l3vpn-svc { namespace "urn:ietf:params:xml:ns:yang:ietf-l3vpn-svc"; prefix l3vpn-svc; import ietf-routing { prefix "rt"; } import ietf-inet-types { prefix inet; } import ietf-yang-types { prefix yang; } organization "IETF L3SM Working Group"; contact "WG List: <mailto:l3sm@ietf.org> Editor: "; description Litkowski, et al. Expires September 4, 2016 [Page 60] Internet-Draft l3vpn-svc-cfg March 2016 "The YANG module defines a generic service configuration model for Layer 3 VPN common across all of the vendor implementations."; revision 2016-01-04 { description " * Add extranet-vpn container in vpn-svc * Creating top level containers * Refine groupings * Added site-vpn-flavor "; reference "draft-ietf-l3sm-l3vpn-service-yang-03"; } revision 2016-01-04 { description " * qos-profile moved to choice * vpn leaf moved to vpn-id in vpn-policy * added ordered-by user to qos classification list * moved traffic protection to access availability * creating a choice in matching filter for VPN policy * added dot1p matching field in flow-definition "; reference ""; } revision 2015-12-07 { description " * A site is now a collection of site-accesses. This was introduced to support M to N availability. * Site-availability has been removed, replaced by availability parameters under site-accesses * Added transport-constraints within vpn-svc "; reference "draft-ietf-l3sm-l3vpn-service-yang-02"; } revision 2015-11-03 { description " * Add ToS support in match-flow * nexthop in cascaded lan as mandatory * customer-specific-info deleted and moved to routing protocols * customer-lan-connection modified : need prefix and CE address * add choice in managing PE-CE addressing Litkowski, et al. Expires September 4, 2016 [Page 61] Internet-Draft l3vpn-svc-cfg March 2016 * Simplifying traffic protection "; reference ""; } revision 2015-09-10 { description " * Refine groupings for vpn-svc * Removed name in vpn-svc * id in vpn-svc moved to string * Rename id in vpn-svc to vpn-id * Changed key of vpn-svc list to vpn-id * Add DSCP support in flow definition "; reference ""; } revision 2015-08-07 { description " Multicast : * Removed ACL from security * Add FW for site and cloud access "; reference ""; } revision 2015-08-05 { description " Multicast : * Removed anycast-rp identity as discovery mechanism * Added rp-group mappings for multicast * Added flag for provider managed RP. "; reference ""; } revision 2015-08-03 { description " * Creating multiple reusable groupings * Added mpls leaf in vpn-svc for carrier's carrier case * Modify identity single to single-site * Modify site-type to site-role and also child identities. * Creating OAM container under site and moved BFD in. * Creating flow-definition grouping to be reused in ACL, QoS ... * Simplified VPN policy. * Adding multicast static group to RP mappings. * Removed native-vpn and site-role from global site cfg, now managed within the VPN policy. * Creating a separate list for site templates. Litkowski, et al. Expires September 4, 2016 [Page 62] Internet-Draft l3vpn-svc-cfg March 2016 "; reference "draft-ietf-l3sm-l3vpn-service-yang-01"; } revision 2015-07-02 { reference "draft-ietf-l3sm-l3vpn-service-yang-00"; } revision 2015-04-24 { description " * Add encryption parameters * Adding holdtime for BFD. * Add postal address in location "; reference "draft-lstd-l3sm-l3vpn-service-yang-00"; } revision 2015-02-05 { description "Initial revision."; reference "draft-l3vpn-service-yang-00"; } /* Typedefs */ typedef svc-id { type string; description "Defining a type of service component identificators."; } typedef template-id { type string; description "Defining a type of service template identificators."; } typedef placement-diversity { type enumeration { enum "pop-diverse" { description "The access must use another PoP compared to other accesses in the same group."; } enum "pe-diverse" { description "The access must use another PE compared to other accesses in the same group."; Litkowski, et al. Expires September 4, 2016 [Page 63] Internet-Draft l3vpn-svc-cfg March 2016 } } description "Defines a type for service placement diversity."; } /* Identities */ identity site-vpn-flavor { description "Base identity for the site VPN service flavor."; } identity site-vpn-flavor-single { base site-vpn-flavor; description "Base identity for the site VPN service flavor. Used when the site belongs to only one VPN."; } identity site-vpn-flavor-multi { base site-vpn-flavor; description "Base identity for the site VPN service flavor. Used when a logical connection of a site belongs to multiple VPNs."; } /* identity site-vpn-flavor-sub { base site-vpn-flavor; description "Base identity for the site VPN service flavor. Used when a site has multiple logical connections and each logical connection belongs to a single particular VPN."; } identity site-vpn-flavor-submulti { base site-vpn-flavor; description "Base identity for the site VPN service flavor. Used when a site has multiple logical connections and each logical connection may belong to multiple VPNs with independent rules."; } */ identity transport-constraint { description "Base identity for transport constraint."; } Litkowski, et al. Expires September 4, 2016 [Page 64] Internet-Draft l3vpn-svc-cfg March 2016 identity tc-latency { base transport-constraint; description "Base identity for transport constraint based on latency."; } identity tc-jitter { base transport-constraint; description "Base identity for transport constraint based on jitter."; } identity tc-bandwidth { base transport-constraint; description "Base identity for transport constraint based on bandwidth."; } identity tc-path-diversity { base transport-constraint; description "Base identity for transport constraint based on path diversity."; } identity tc-site-diversity { base transport-constraint; description "Base identity for transport constraint based on site diversity."; } identity management { description "Base identity for site management scheme."; } identity comanaged { base management; description "Base identity for comanaged site."; } identity customer-managed { base management; description "Base identity for customer managed site."; } identity provider-managed { base management; description Litkowski, et al. Expires September 4, 2016 [Page 65] Internet-Draft l3vpn-svc-cfg March 2016 "Base identity for provider managed site."; } identity address-allocation-type { description "Base identity for address-allocation-type for PE-CE link."; } identity pe-dhcp { base address-allocation-type; description "PE router provides DHCP service to CE."; } identity static-address { base address-allocation-type; description "PE-CE addressing is static."; } identity slaac { base address-allocation-type; description "Use IPv6 SLAAC."; } /* identity site-availability { description "Base identity for site availability."; } identity loadsharing { base site-availability; description "Identity for loadsharing site."; } identity loadsharing-ibgp { base loadsharing; description "Identity for ECMP ibgp based loadsharing site."; } identity loadsharing-eibgp { base loadsharing; description "Identity for ECMP eibgp based loadsharing site."; } identity primary-backup { base site-availability; description "Identity for primary-backup site."; Litkowski, et al. Expires September 4, 2016 [Page 66] Internet-Draft l3vpn-svc-cfg March 2016 } identity single-site { base site-availability; description "Identity for single site."; } identity access-availability-type { description "base identity for access-availability-type"; } identity primary-access { base access-availability-type; description "Identity for primary access type."; } identity backup-access { base access-availability-type; description "Identity for backup access type."; } identity single-access { base access-availability-type; description "Identity for single access type."; } identity loadsharing-access { base access-availability-type; description "Identity for loadsharing access type."; } */ identity site-role { description "Base identity for site type."; } identity any-to-any-role { base site-role; description "Site in a any to any IPVPN."; } identity spoke-role { base site-role; description "Spoke Site in a Hub & Spoke IPVPN."; } identity hub-role { Litkowski, et al. Expires September 4, 2016 [Page 67] Internet-Draft l3vpn-svc-cfg March 2016 base site-role; description "Hub Site in a Hub & Spoke IPVPN."; } identity vpn-topology { description "Base identity for VPN topology."; } identity any-to-any { base vpn-topology; description "Identity for any to any VPN topology."; } identity hub-spoke { base vpn-topology; description "Identity for Hub'n'Spoke VPN topology."; } identity hub-spoke-disjoint { base vpn-topology; description "Identity for Hub'n'Spoke VPN topology where Hubs cannot talk between each other."; } identity multicast-tree-type { description "Base identity for multicast tree type."; } identity ssm-tree-type { base multicast-tree-type; description "Identity for SSM tree type."; } identity asm-tree-type { base multicast-tree-type; description "Identity for ASM tree type."; } identity bidir-tree-type { base multicast-tree-type; description "Identity for BiDir tree type."; } Litkowski, et al. Expires September 4, 2016 [Page 68] Internet-Draft l3vpn-svc-cfg March 2016 identity multicast-rp-discovery-type { description "Base identity for rp discovery type."; } identity auto-rp { base multicast-rp-discovery-type; description "Base identity for auto-rp discovery type."; } identity static-rp { base multicast-rp-discovery-type; description "Base identity for static type."; } identity bsr-rp { base multicast-rp-discovery-type; description "Base identity for BDR discovery type."; } identity routing-protocol-type { description "Base identity for routing-protocol type."; } identity ospf { base routing-protocol-type; description "Identity for OSPF protocol type."; } identity bgp { base routing-protocol-type; description "Identity for BGP protocol type."; } identity static { base routing-protocol-type; description "Identity for static routing protocol type."; } identity rip { base routing-protocol-type; description "Identity for RIP protocol type."; } Litkowski, et al. Expires September 4, 2016 [Page 69] Internet-Draft l3vpn-svc-cfg March 2016 identity rip-ng { base routing-protocol-type; description "Identity for RIPng protocol type."; } identity vrrp { base routing-protocol-type; description "Identity for VRRP protocol type. This is to be used when LAn are directly connected to provider Edge routers."; } identity direct { base routing-protocol-type; description "Identity for direct protocol type. ."; } identity protocol-type { description "Base identity for protocol field type."; } identity tcp { base protocol-type; description "TCP protocol type."; } identity udp { base protocol-type; description "UDP protocol type."; } identity icmp { base protocol-type; description "icmp protocol type."; } identity icmp6 { base protocol-type; description "icmp v6 protocol type."; } identity gre { base protocol-type; Litkowski, et al. Expires September 4, 2016 [Page 70] Internet-Draft l3vpn-svc-cfg March 2016 description "GRE protocol type."; } identity ipip { base protocol-type; description "IPinIP protocol type."; } identity hop-by-hop { base protocol-type; description "Hop by Hop IPv6 header type."; } identity routing { base protocol-type; description "Routing IPv6 header type."; } identity esp { base protocol-type; description "ESP header type."; } identity ah { base protocol-type; description "AH header type."; } /* Groupings */ grouping vpn-service-cloud-access { list cloud-access { key cloud-identifier; leaf cloud-identifier { type string; description "Identification of cloud service. Local admin meaning."; } list authorized-sites { Litkowski, et al. Expires September 4, 2016 [Page 71] Internet-Draft l3vpn-svc-cfg March 2016 key site-id; leaf site-id { type leafref { path "/l3vpn-svc/sites/site/site-id"; } description "Site ID."; } description "List of authorized sites."; } list denied-sites { key site-id; leaf site-id { type leafref { path "/l3vpn-svc/sites/site/site-id"; } description "Site ID."; } description "List of denied sites."; } leaf nat-enabled { type boolean; description "Control if NAT is required or not."; } leaf customer-nat-address { type inet:ipv4-address; description "NAT address to be used in case of public or shared cloud. This is to be used in case customer is providing the public address."; } description "Cloud access configuration."; } description "grouping for vpn cloud definition"; } grouping vpn-service-multicast { container multicast { leaf enabled { Litkowski, et al. Expires September 4, 2016 [Page 72] Internet-Draft l3vpn-svc-cfg March 2016 type boolean; default false; description "Enable multicast."; } container customer-tree-flavors { list tree-flavor { key type; leaf type { type identityref { base multicast-tree-type; } description "Type of tree to be used."; } description "List of tree flavors."; } description "Type of trees used by customer."; } container rp { list rp-group-mapping { key "rp-address group"; container provider-managed { leaf enabled { type boolean; default false; description "Set to true, if the RP must be a provider managed node. Set to false, if it is a customer managed node."; } leaf anycast-rp { type boolean; default false; description "Enables anycast-RP."; } description "Parameters for provider managed RP."; Litkowski, et al. Expires September 4, 2016 [Page 73] Internet-Draft l3vpn-svc-cfg March 2016 } leaf rp-address { type union { type inet:ipv4-address; type inet:ipv6-address; } description "Defines the address of the RendezvousPoint. Used if RP is customer managed."; } leaf group { type union { type inet:ipv4-address; type inet:ipv6-address; } description "Defines the address of the multicast group handled by the RP."; } description "List of RP to group mappings."; } leaf rp-discovery { type identityref { base multicast-rp-discovery-type; } description "Type of RP discovery used."; } description "RendezvousPoint parameters."; } description "Multicast global parameters for the VPN service."; } description "grouping for multicast vpn definition"; } grouping vpn-service-mpls { leaf mpls { type boolean; default false; description "The VPN is using Carrier Supporting Carrier, Litkowski, et al. Expires September 4, 2016 [Page 74] Internet-Draft l3vpn-svc-cfg March 2016 and so MPLS is required."; } description "grouping for mpls CsC definition"; } grouping customer-location-info { container location { leaf address { type string; description "Address (number and street) of the site."; } leaf zip-code { type string; description "ZIP code of the site."; } leaf city { type string; description "City of the site."; } leaf country-code { type string; description "Country of the site."; } description "Location of the site."; } description "This grouping defines customer location parameters"; } grouping site-diversity { container site-diversity { leaf type { type placement-diversity; description "Diversity constraint type."; } leaf-list site-group { Litkowski, et al. Expires September 4, 2016 [Page 75] Internet-Draft l3vpn-svc-cfg March 2016 type uint32; description "IDs of group."; } description "Diversity constraint type."; } description "This grouping defines site diversity parameters"; } grouping access-diversity { container access-diversity { leaf type { type placement-diversity; default "pe-diverse"; description "Diversity constraint type."; } description "Diversity constraint type."; } description "This grouping defines access diversity parameters"; } grouping operational-requirements { leaf requested-site-start { type yang:date-and-time; description "Optional leaf indicating requested date and time when the service at a particular site is expected to start"; } leaf requested-site-stop { type yang:date-and-time; description "Optional leaf indicating requested date and time when the service at a particular site is expected to stop"; } Litkowski, et al. Expires September 4, 2016 [Page 76] Internet-Draft l3vpn-svc-cfg March 2016 leaf actual-site-start { type yang:date-and-time; description "Optional leaf indicating actual date and time when the service at a particular site actually started"; } leaf actual-site-stop { type yang:date-and-time; description "Optional leaf indicating actual date and time when the service at a particular site actually stopped"; } description "This grouping defines some operational parameters parameters"; } grouping flow-definition { container match-flow { leaf dscp { type uint8 { range "0 .. 63"; } description "DSCP value."; } leaf tos { type uint8 { range "0 .. 254"; } description "TOS value."; } leaf dot1p { type uint8 { range "0 .. 7"; } description "802.1p matching."; } leaf ipv4-src-prefix { Litkowski, et al. Expires September 4, 2016 [Page 77] Internet-Draft l3vpn-svc-cfg March 2016 type inet:ipv4-prefix; description "Match on IPv4 src address."; } leaf ipv6-src-prefix { type inet:ipv6-prefix; description "Match on IPv6 src address."; } leaf ipv4-dst-prefix { type inet:ipv4-prefix; description "Match on IPv4 dst address."; } leaf ipv6-dst-prefix { type inet:ipv6-prefix; description "Match on IPv6 dst address."; } leaf l4-src-port { type uint16; description "Match on layer 4 src port."; } leaf l4-dst-port { type uint16; description "Match on layer 4 dst port."; } leaf protocol-field { type union { type uint8; type identityref { base protocol-type; } } description "Match on IPv4 protocol or Ipv6 Next Header field."; } description "Describe flow matching criterions."; } description "Flow definition based on criteria."; Litkowski, et al. Expires September 4, 2016 [Page 78] Internet-Draft l3vpn-svc-cfg March 2016 } grouping site-service-basic { leaf svc-input-bandwidth { type uint32; units bps; description "From the PE perspective, the service input bandwidth of the connection."; } leaf svc-output-bandwidth { type uint32; units bps; description "From the PE perspective, the service output bandwidth of the connection."; } leaf svc-mtu { type uint16; units bytes; description "MTU at service level. If the service is IP, it refers to the IP MTU."; } description "Defines basic service parameters for a site."; } grouping site-access-protection { container traffic-protection { leaf enabled { type boolean; description "Enables traffic protection of access link."; } description "Fast reroute service parameters for the site."; } description "Defines protection service parameters for a site."; } grouping site-service-mpls { container mpls { leaf signalling-type { type enumeration { enum "ldp" { Litkowski, et al. Expires September 4, 2016 [Page 79] Internet-Draft l3vpn-svc-cfg March 2016 description "Use LDP as signalling protocol between PE and CE."; } enum "bgp" { description "Use BGP 3107 as signalling protocol between PE and CE. In this case, bgp must be also configured as routing-protocol. "; } } description "MPLS signalling type."; } description "This container is used when customer provides MPLS based services. This is used in case of Carrier Supporting Carrier."; } description "Defines MPLS service parameters for a site."; } grouping site-service-qos-profile { container qos { container qos-classification-policy { list rules { key id; ordered-by user; leaf id { type uint16; description "ID of the rule."; } uses flow-definition; leaf target-class-id { type string; description "Identification of the class of service. This identifier is internal to the administration."; } Litkowski, et al. Expires September 4, 2016 [Page 80] Internet-Draft l3vpn-svc-cfg March 2016 description "List of marking rules."; } description "Need to express marking rules ..."; } choice qos-profile { description "Choice for QoS profile. Can be standard profile or custom."; case standard { leaf profile { type string; description "QoS profile to be used"; } } case custom { container classes { list class { key class-id; leaf class-id { type string; description "Identification of the class of service. This identifier is internal to the administration."; } leaf rate-limit { type uint8; units percent; description "To be used if class must be rate limited. Expressed as percentage of the svc-bw."; } leaf priority-level { type uint8; description "Defines the level of the class in term of priority queueing. The higher the level is the higher is the priority."; Litkowski, et al. Expires September 4, 2016 [Page 81] Internet-Draft l3vpn-svc-cfg March 2016 } leaf guaranteed-bw-percent { type uint8; units percent; description "To be used to define the guaranteed BW in percent of the svc-bw available at the priority-level."; } description "List of class of services."; } description "Container for list of class of services."; } } } description "QoS configuration."; } description "This grouping defines QoS parameters for a site"; } grouping site-security-authentication { container authentication { description "Authentication parameters"; } description "This grouping defines authentication parameters for a site"; } grouping site-security-encryption { container encryption { leaf enabled { type boolean; description "If true, access encryption is required."; } leaf layer { Litkowski, et al. Expires September 4, 2016 [Page 82] Internet-Draft l3vpn-svc-cfg March 2016 type enumeration { enum layer2 { description "Encryption will occur at layer2."; } enum layer3 { description "IPSec is requested."; } } description "Layer on which encryption is applied."; } container encryption-profile { choice profile { case provider-profile { leaf profile-name { type string; description "Name of the SP profile to be applied."; } } case customer-profile { leaf algorithm { type string; description "Encryption algorithm to be used."; } choice key-type { case psk { leaf preshared-key { type string; description "Key coming from customer."; } } case pki { } description "Type of keys to be used."; } } description "Choice of profile."; Litkowski, et al. Expires September 4, 2016 [Page 83] Internet-Draft l3vpn-svc-cfg March 2016 } description "Profile of encryption to be applied."; } description "Encryption parameters."; } description "This grouping defines encryption parameters for a site"; } grouping site-attachment-bearer { container bearer { leaf type { type string; description "Type of bearer Ethernet, DSL, Wireless ... Operator specific."; } leaf bearer-reference { type string; description "This is an internal reference for the service provider."; } description "Bearer specific parameters. To be augmented."; } description "Defines physical properties of a site attachment."; } grouping site-routing { container routing-protocols { list routing-protocol { key type; leaf type { type identityref { base routing-protocol-type; } description "Type of routing protocol."; } Litkowski, et al. Expires September 4, 2016 [Page 84] Internet-Draft l3vpn-svc-cfg March 2016 container ospf { when "../type = 'ospf'" { description "Only applies when protocol is OSPF."; } leaf-list address-family { type identityref { base rt:address-family; } description "Address family to be activated."; } leaf area-address { type yang:dotted-quad; description "Area address."; } leaf metric { type uint16; description "Metric of PE-CE link."; } list sham-link { key target-site; leaf target-site { type svc-id; description "Target site for the sham link connection. The site is referred through it's ID."; } leaf metric { type uint16; description "Metric of the sham link."; } description "Creates a shamlink with another site"; } description "OSPF specific configuration."; } container bgp { when "../type = 'bgp'" { Litkowski, et al. Expires September 4, 2016 [Page 85] Internet-Draft l3vpn-svc-cfg March 2016 description "Only applies when protocol is BGP."; } leaf autonomous-system { type uint32; description "AS number."; } leaf-list address-family { type identityref { base rt:address-family; } description "Address family to be activated."; } description "BGP specific configuration."; } container static { when "../type = 'static'" { description "Only applies when protocol is static."; } container cascaded-lan-prefixes { list ipv4-lan-prefixes { key "lan next-hop"; leaf lan { type inet:ipv4-prefix; description "Lan prefixes."; } leaf lan-tag { type string; description "Internal tag to be used in vpn policies."; } leaf next-hop { type inet:ipv4-address; description "Nexthop address to use at customer side."; } description " Litkowski, et al. Expires September 4, 2016 [Page 86] Internet-Draft l3vpn-svc-cfg March 2016 List of LAN prefixes for the site. "; } list ipv6-lan-prefixes { key "lan next-hop"; leaf lan { type inet:ipv6-prefix; description "Lan prefixes."; } leaf lan-tag { type string; description "Internal tag to be used in vpn policies."; } leaf next-hop { type inet:ipv6-address; description "Nexthop address to use at customer side."; } description " List of LAN prefixes for the site. "; } description "LAN prefixes from the customer."; } description "Static routing specific configuration."; } container rip { when "../type = 'rip'" { description "Only applies when protocol is RIP."; } leaf-list address-family { type identityref { base rt:address-family; } description "Address family to be activated."; Litkowski, et al. Expires September 4, 2016 [Page 87] Internet-Draft l3vpn-svc-cfg March 2016 } description "RIP routing specific configuration."; } container vrrp { when "../type = 'vrrp'" { description "Only applies when protocol is VRRP."; } leaf-list address-family { type identityref { base rt:address-family; } description "Address family to be activated."; } description "VRRP routing specific configuration."; } description "List of routing protocols used on the site. Need to be augmented."; } description "Defines routing protocols."; } description "Grouping for routing protocols."; } grouping site-attachment-ip-connection { container ip-connection { container ipv4 { leaf address-allocation-type { type identityref { base address-allocation-type; } description "Defines how addresses are allocated. Need to be detailed further."; Litkowski, et al. Expires September 4, 2016 [Page 88] Internet-Draft l3vpn-svc-cfg March 2016 } choice subnet { case subnet-only { leaf subnet-prefix { type inet:ipv4-prefix; description "Interco subnet."; } } case addresses { leaf provider-address { type inet:ipv4-address; description "Provider side address."; } leaf customer-address { type inet:ipv4-address; description "Customer side address."; } leaf mask { type uint8 { range "0..32"; } description "Subnet mask expressed in bits"; } } description "Choice for addressing customer to network link."; } description "IPv4 specific parameters"; } container ipv6 { leaf address-allocation-type { type string; description "Defines how addresses are allocated. Need to be detailled further."; } choice subnet { case subnet-only { leaf subnet-prefix { Litkowski, et al. Expires September 4, 2016 [Page 89] Internet-Draft l3vpn-svc-cfg March 2016 type inet:ipv6-prefix; description "Interco subnet."; } } case addresses { leaf provider-address { type inet:ipv6-address; description "Provider side address."; } leaf customer-address { type inet:ipv6-address; description "Customer side address."; } leaf mask { type uint8 { range "0..128"; } description "Subnet mask expressed in bits"; } } description "Choice for addressing customer to network link."; } description "IPv6 specific parameters"; } container oam { container bfd { leaf bfd-enabled { type boolean; description "BFD activation"; } choice holdtime { case profile { leaf profile-name { type string; description "Service provider well known profile."; Litkowski, et al. Expires September 4, 2016 [Page 90] Internet-Draft l3vpn-svc-cfg March 2016 } description "Service provider well known profile."; } case fixed { leaf fixed-value { type uint32; units msec; description "Expected holdtime expressed in msec."; } } description "Choice for holdtime flavor."; } description "Container for BFD."; } description "Define the OAM used on the connection."; } description "Defines connection parameters."; } description "This grouping defines IP connection parameters."; } grouping site-service-multicast { container multicast { leaf multicast-site-type { type enumeration { enum receiver-only { description "The site has only receivers."; } enum source-only { description "The site has only sources."; } enum source-receiver { description "The site has both sources & receivers."; } Litkowski, et al. Expires September 4, 2016 [Page 91] Internet-Draft l3vpn-svc-cfg March 2016 } default "source-receiver"; description "Type of multicast site."; } container multicast-transport-protocol { leaf ipv4 { type boolean; default true; description "Enables ipv4 multicast transport"; } leaf ipv6 { type boolean; default false; description "Enables ipv6 multicast transport"; } description "Defines protocol to transport multicast."; } leaf protocol-type { type enumeration { enum host { description " Hosts are directly connected to the provider network. Host protocols like IGMP, MLD are required. "; } enum router { description " Hosts are behind a customer router. PIM will be implemented. "; } enum both { description "Some Hosts are behind a customer router and some others are directly connected to the provider network. Both host and routing protocols must be used. Typically IGMP and PIM will be implemented. "; Litkowski, et al. Expires September 4, 2016 [Page 92] Internet-Draft l3vpn-svc-cfg March 2016 } } default "both"; description "Multicast protocol type to be used with the customer site."; } description "Multicast parameters for the site."; } description "Multicast parameters for the site."; } grouping site-management { container management { leaf type { type identityref { base management; } description "Management type of the connection."; } leaf management-transport { type identityref { base rt:address-family; } description "Transport protocol used for management."; } leaf address { type union { type inet:ipv4-address; type inet:ipv6-address; } description "Management address"; } description "Management configuration"; } description "Management parameters for the site."; } grouping site-vpn-flavor { Litkowski, et al. Expires September 4, 2016 [Page 93] Internet-Draft l3vpn-svc-cfg March 2016 leaf site-vpn-flavor { type identityref { base site-vpn-flavor; } default site-vpn-flavor-single; description "Defines if the site is a single VPN site, or multiVPN or ..."; } description "Grouping for site-vpn-flavor."; } grouping site-vpn-policy { container vpn-policy { list entries { key id; leaf id { type svc-id; description "Unique identifier for the policy entry."; } container filter { choice lan { case lan-prefix { container lan-prefixes { list ipv4-lan-prefixes { key lan; leaf lan { type inet:ipv4-prefix; description "Lan prefixes."; } description " List of LAN prefixes for the site. "; } list ipv6-lan-prefixes { key lan; leaf lan { type inet:ipv6-prefix; description "Lan prefixes."; Litkowski, et al. Expires September 4, 2016 [Page 94] Internet-Draft l3vpn-svc-cfg March 2016 } description " List of LAN prefixes for the site. "; } description "LAN prefixes from the customer."; } } case lan-tag { leaf-list lan-tag { type string; description "List of lan-tags to be matched."; } } description "Choice for LAN matching type"; } description "If used, it permit to split site LANs among multiple VPNs. If no filter used, all the LANs will be part of the same VPNs with the same role."; } container vpn { leaf vpn-id { type leafref { path "/l3vpn-svc/vpn-services/"+ "vpn-svc/vpn-id"; } mandatory true; description "Reference to an IPVPN."; } leaf site-role { type identityref { base site-role; } mandatory true; description "Role of the site in the IPVPN."; } description "List of VPNs the LAN is associated to."; } Litkowski, et al. Expires September 4, 2016 [Page 95] Internet-Draft l3vpn-svc-cfg March 2016 description "List of entries for export policy."; } description "VPN policy."; } description "VPN policy parameters for the site."; } grouping site-maximum-routes { container maximum-routes { list address-family { key af; leaf af { type identityref { base rt:address-family; } description "Address-family."; } leaf maximum-routes { type uint32; description "Maximum prefixes the VRF can accept for this address-family."; } description "List of address families."; } description "Define maximum-routes for the VRF."; } description "Define maximum-routes for the site."; } grouping site-security { container security { uses site-security-authentication; uses site-security-encryption; description Litkowski, et al. Expires September 4, 2016 [Page 96] Internet-Draft l3vpn-svc-cfg March 2016 "Site specific security parameters."; } description "Grouping for security parameters."; } grouping site-service { container service { uses site-service-basic; uses site-service-qos-profile; uses site-service-mpls; uses site-service-multicast; description "Service parameters on the attachement."; } description "Grouping for service parameters."; } grouping transport-constraint { list constraint-list { key constraint-type; leaf constraint-type { type identityref { base transport-constraint; } description "Constraint type to be applied."; } leaf constraint-opaque-value { type string; description "Opaque value that can be used to specify constraint parameters."; } description "List of constraints"; } description "Grouping for transport constraint."; } grouping transport-constraints { container transport-constraints { container unicast-transport-constraints { list constraints { Litkowski, et al. Expires September 4, 2016 [Page 97] Internet-Draft l3vpn-svc-cfg March 2016 key constraint-id; leaf constraint-id { type svc-id; description "Defines an ID for the constraint rule."; } leaf site1 { type svc-id; description "The ID refers to one site end."; } leaf site2 { type svc-id; description "The ID refers to the other site end."; } uses transport-constraint; description "List of constraints. Constraints are bidirectional."; } description "Unicast transport constraints."; } container multicast-transport-constraints { list constraints { key constraint-id; leaf constraint-id { type svc-id; description "Defines an ID for the constraint rule."; } leaf src-site { type svc-id; description "The ID refers to source site."; } leaf dst-site { type svc-id; description "The ID refers to the receiver Litkowski, et al. Expires September 4, 2016 [Page 98] Internet-Draft l3vpn-svc-cfg March 2016 site."; } uses transport-constraint; description "List of constraints. Constraints are unidirectional."; } description "Multicast transport constraints."; } description "transport constraints."; } description "Grouping for transport constraints description."; } grouping vpn-extranet { container extranet-vpns { list extranet-vpn { key vpn-id; leaf vpn-id { type svc-id; description "Identifies the target VPN"; } leaf local-sites-role { type identityref { base site-role; } description "This describes the role of the local sites in the target VPN topology."; } description "List of extranet VPNs the local VPN is attached to."; } description "Container for extranet vpn cfg."; } description "grouping for extranet VPN configuration. Extranet provides a way to interconnect all sites from two VPNs in a easy way."; Litkowski, et al. Expires September 4, 2016 [Page 99] Internet-Draft l3vpn-svc-cfg March 2016 } grouping site-attachment-availability { container availability { uses site-access-protection; leaf access-priority { type uint32; default 1; description "Defines the priority for the access. The highest the priority value is, the highest the preference of the access is."; } description "Availability parameters (used for multihoming)"; } description "Defines site availability parameters."; } grouping vpn-svc-cfg { leaf vpn-id { type svc-id; description "VPN identifier. Local administration meaning."; } leaf customer-name { type string; description "Name of the customer."; } leaf topology { type identityref { base vpn-topology; } default "any-to-any"; description "VPN topology."; } uses vpn-service-cloud-access; uses vpn-service-multicast; uses vpn-service-mpls; uses transport-constraints; uses vpn-extranet; Litkowski, et al. Expires September 4, 2016 [Page 100] Internet-Draft l3vpn-svc-cfg March 2016 description "grouping for vpn-svc configuration."; } grouping site-top-level-cfg { uses operational-requirements; uses customer-location-info; uses site-diversity; uses site-management; uses site-vpn-policy; uses site-vpn-flavor; uses site-maximum-routes; uses site-security; uses site-service; uses site-routing; description "Grouping for site top level cfg."; } grouping site-network-access-top-level-cfg { uses access-diversity; uses site-attachment-bearer; uses site-attachment-ip-connection; uses site-security; uses site-service; uses site-routing; uses site-attachment-availability; description "Grouping for site network access top level cfg."; } /* Main blocks */ container l3vpn-svc { container vpn-services { list vpn-svc { key vpn-id; uses vpn-svc-cfg; description " List of VPN services. "; } description "top level container Litkowski, et al. Expires September 4, 2016 [Page 101] Internet-Draft l3vpn-svc-cfg March 2016 for the VPN services."; } container sites { list site { key site-id; leaf site-id { type svc-id; description "Identifier of the site."; } leaf apply-template { type leafref { path "/l3vpn-svc/site-templates"+ "/site-template/site-template-id"; } description "Reference to template to be applied. The template is called through it's ID."; } uses site-top-level-cfg; container site-network-accesses { list site-network-access { key site-network-access-id; leaf site-network-access-id { type svc-id; description "Identifier for the access"; } leaf apply-template { type leafref { path "/l3vpn-svc/site-templates/"+ "site-template/site-template-id"; } description "Reference to template to be applied. The template is called through it's ID."; } uses site-network-access-top-level-cfg; description "List of accesses for a site."; } Litkowski, et al. Expires September 4, 2016 [Page 102] Internet-Draft l3vpn-svc-cfg March 2016 description "List of accesses for a site."; } description "List of sites."; } description "Container for sites"; } container site-templates { list site-template { key site-template-id; leaf site-template-id { type template-id; description "Identifier of the site."; } uses site-top-level-cfg; container site-network-access { uses site-network-access-top-level-cfg; description "Container for the site-network-access."; } description "List of sites."; } description "Container for site templates"; } description "Main container for L3VPN service configuration."; } } 9. Security Considerations TBD. Litkowski, et al. Expires September 4, 2016 [Page 103] Internet-Draft l3vpn-svc-cfg March 2016 10. Acknowledgements Thanks to Qin Wu, Maxim Klyus, Luis Miguel Contreras, Gregory Mirsky, Zitao Wang, Jing Zhao, Kireeti Kompella, Eric Rosen, Aijun Wang, Kenichi Ogaki and Andrew Leu for the contributions to the document. 11. IANA Considerations TBD. 12. References 12.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/ RFC2119, March 1997, . [RFC4364] Rosen, E. and Y. Rekhter, "BGP/MPLS IP Virtual Private Networks (VPNs)", RFC 4364, DOI 10.17487/RFC4364, February 2006, . [RFC4577] Rosen, E., Psenak, P., and P. Pillay-Esnault, "OSPF as the Provider/Customer Edge Protocol for BGP/MPLS IP Virtual Private Networks (VPNs)", RFC 4577, DOI 10.17487/RFC4577, June 2006, . [RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless Address Autoconfiguration", RFC 4862, DOI 10.17487/ RFC4862, September 2007, . [RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, October 2010, . [RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011, . [RFC6513] Rosen, E., Ed. and R. Aggarwal, Ed., "Multicast in MPLS/ BGP IP VPNs", RFC 6513, DOI 10.17487/RFC6513, February 2012, . Litkowski, et al. Expires September 4, 2016 [Page 104] Internet-Draft l3vpn-svc-cfg March 2016 12.2. Informative References [RFC4110] Callon, R. and M. Suzuki, "A Framework for Layer 3 Provider-Provisioned Virtual Private Networks (PPVPNs)", RFC 4110, DOI 10.17487/RFC4110, July 2005, . Appendix A. Example: NETCONF Reply This section gives an example of a reply to the NETCONF request for a device that implements the data model defined in this document. The example is written in XML. Authors' Addresses Stephane Litkowski Orange Business Service Email: stephane.litkowski@orange.com Rob Shakir BT Email: rob.shakir@bt.com Luis Tomotaki Verizon Email: luis.tomotaki@verizon.com Kevin D'Souza ATT Email: kd6913@att.com Litkowski, et al. Expires September 4, 2016 [Page 105]