iSCSI March 1, 2002 IPS Julian Satran Internet Draft Daniel Smith draft-ietf-ips-iscsi-11.txt Kalman Meth Category: standards-track Ofer Biran Jim Hafner IBM Costa Sapuntzakis Mark Bakke Cisco Systems Randy Haagens Mallikarjun Chadalapaka Hewlett-Packard Co. Matt Wakeley Agilent Technologies Luciano Dalle Ore Quantum Paul Von Stamwitz Adaptec Efri Zeidner SANGate iSCSI Julian Satran Expires August 2002 1 11iSCSI.book Page 2 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Status of this Memo This document is an Internet-Draft and fully conforms to all provi- sions of Section 10 of [RFC2026]. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet-Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or made obsolete by other documents at any time. It is inappropriate to use Internet- Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http:// www.ietf.org/ietf/1id-abstracts.txt The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. Abstract The Small Computer Systems Interface (SCSI) is a popular family of protocols for communicating with I/O devices, especially storage devices. This memo describes a transport protocol for SCSI that oper- ates on top of TCP. The iSCSI protocol aims to be fully compliant with the requirements laid out in the SCSI Architecture Model - 2 [SAM2] document. Acknowledgements In addition to the authors, a large group of people contributed to this work through their review, comments and valuable insights. We are grateful to all of them. We are especially grateful to those who found the time and patience to participate in our weekly phone conferences and intermediate meetings in Almaden and Haifa, thus helping to shape this document: John Hufferd, Prasenjit Sarkar, Meir Toledano, John Dowdy, Steve Legg, Alain Azagury (IBM), Dave Nagle (CMU), David Black (EMC), John Matze (Veritas - now with Stonefly Networks), Steve DeGroote, Mark Schrandt (NuSpeed), Gabi Hecht (Gadzoox), Robert Sniv- ely (Brocade), Nelson Nachum (StorAge), Uri Elzur (Broadcom). Many more helped clean up and improve this document within the IPS working group. We are especially grateful to David Robinson and Raghavendra Rao (Sun), Charles Monia, Joshua Tseng (Nishan), Somesh Gupta (Sil- verback Systems), Michael Krause, Pierre Labat, Santosh Rao, Matthew Burbridge (HP), Stephen Bailey (Sandburst), Robert Elliott, Martin Julian Satran Expires August 2002 2 11iSCSI.book Page 3 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Nick (Compaq), Steve Senum, Ayman Ghanem (CISCO), Barry Reinhold (Trebia Networks), Bob Russell (UNH), Bill Lynn (Adaptec), Doug Otis (Sanlight), Robert Griswold and Bill Moody (Crossroads). The recovery chapter was enhanced with help from Stephen Bailey (Sandburst), Somesh Gupta (HP), Venkat Rangan (Rhapsody Networks), Vince Cavanna, Pat Thaler (Agilent), Jonathan Stone (Stanford), Eddy Quicksall (iVivity, Inc.) - Eddy also contributed with some examples. Last, but not least, thanks to Ralph Weber for keeping us in line with T10 (SCSI) standardization. We would like to thank Steve Hetzler for his unwavering support and for coming up with such a good name for the protocol, Micky Rodeh, Jai Menon, Clod Barrera and Andy Bechtolsheim for helping this work hap- pen. At the time of the writing, this document has to be considered in con- junction with the "Naming & Discovery"[NDT], "Boot"[BOOT] and "Secur- ing iSCSI, iFCP and FCIP"[SEC-IPS] documents. The "Naming & Discovery" document is authored by: Mark Bakke (Cisco), Joe Czap, Jim Hafner, John Hufferd, Kaladhar Voruganti (IBM), Howard Hall (Pirus), Jack Harwood (EMC), Yaron Klein (SANRAD), Lawrence Lamers (San Valley Systems), Todd Sperry (Adaptec) and Joshua Tseng (Nishan). The "Boot" document is authored by: Prasenjit Sarkar (IBM), Duncan Missimer (HP) and Costa Sapuntz- akis (CISCO). The "Securing iSCSI, iFCP and FCIP" document is authored by: Bernard Aboba, William Dixon (Microsoft), David Black (EMC), Joseph Tardo, Uri Elzur (Broadcom), Mark Bakke, Steve Senum (Cisco Systems), Howard Herbert, Jesse Walker (Intel), Julian Satran, Ofer Biran and Charles Kunzinger (IBM). We are grateful to all of them for their good work and for helping us correlate this document with the ones they produced. Conventions used in this document In examples, "I->" and "T->" indicate iSCSI PDUs sent by the initiator and target respectively. Julian Satran Expires August 2002 3 11iSCSI.book Page 4 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC2119. Change Log The following changes were made from draft-ietf-ips-iSCSI-10 to draft-ietf-ips-iSCSI-11: - ACA is SHOULD - New format for ISID that allows factory presets - New wording in section 9.5.4 that makes it clear that initia- tor must discard discontiguous data PDUs during reassignment. - Removed Parameter1 field definition for "drop the session" Async Message. - In state transitions chapter, added Logout timeout to the event set causing T17, and removed the "session close" event from the event set for T6. Changed "status class" to Status- Class. - Clarified that for ErrorRecoveryLevel < 2, the X-bit in Login PDU terminates all the tasks. - Clarified the various subcases of interpretation for Time2Retain and Time2Wait in the Logout Response section. - Added a new section in the recovery chapter on connection tim- eout management. - The LogoutLoginMinTime and LogoutLoginMaxTime keys are respectively renamed to DefaultTime2Wait and DefaultTime2Retain, since they are used only on non-Logout events and also to better align with the notion of Time2Wait and Time2Retain that the draft already defines. - Added the new Appendix on clearing effects. - Retired the X-bit in Login PDU to make the bit position reserved. Moved the content under X-bit description to a new section 4.3.4 that describes "connection reinstatement". - Added text to section 6.1.2 that clarifies the expectations on targets during allegiance reassignment. - Minor changes in error recovery algorithms to change NextCmdSN to CmdSN in the Session data structure. - Added a new section 4.3.5 defining the term "session rein- statement". - Added a new transition N11 to target session state diagram, to address the session reinstatement event. Enhancing the event set for N3(T) and N6(I & T) for the same event. Adding the same event to the event sets for target transitions T8, T13, T15, T16, T17, T18, and M2 (I & T). - Addressed the case of active TTTs when ABORT TASK SET/CLEAR TASK SET is in progress in section 9.5 and section 9.6. Julian Satran Expires August 2002 4 11iSCSI.book Page 5 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Added a new Section 9.6.3 Task Management actions on task sets that describes the exact timeline of events on a task set task management function. - Clarified the usage of ITT for DataACK type of SNACK. - Added error code for inexistent session to login response - Changed the FIM SHOULD to should(!) - Added a TTT field for Data-In when A bit is 1 and to the cor- responding SNACK. To make it consistent changed slightly the layout of Data-IN, SCSI Response and SNACK. - Clarified the use of LUN with all PDUs holding TTT - Removed the ? value from negotiations - Unified text negotiations (login, ffp and formats) in one chapter - Clarified AHSLength and DataLength for all PDUs - Clarified use of Reject - Replaced Protocol Error with Negotiation Failure in negotia- tions - Removed FFP command before login from Reject Causes - Added Invalid Request During Login to Login Errors - Added tape text - Clarified Security Text - Aligned marker negotiations with the overall negotiations and added numeric range to the negotiation forms - Changed target network architecture example in Overview - Clarified T bit use in Login Reject - Version bumped to 04 The following changes were made from draft-ietf-ips-iSCSI-09 to draft-ietf-ips-iSCSI-10: - Clarifying MaxOutstandingR2T - Widening the scope of Reject reason code 0x09 to mean "Invalid PDU field". - Changes in the "iSCSI connection termination" section to make the terminology usage consistent with the rest of the draft. - Adding transition T18 in standard connection state diagram, and its description. - Other minor wording changes in the state transitions chapter to address "session close" case and others. - Adding a new state Q5(IN_CONTINUE) to the target session state diagram to resolve transitions N8 and N9 off Q2. - Removed the AHS drop bit feature. - Removed the qualifier field in Task Management Response PDU, and added a new response "Function authorization failed". - Clarified the fate of regular SCSI reservations on a session timeout, compared to a transient session failure. - Added wording in R2T section to address the case of receiving a smaller write data sequence than was asked for in an R2T. Julian Satran Expires August 2002 5 11iSCSI.book Page 6 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Changes and fixes in recovery algorithms to be consistent with the rest of the draft. - Changed the "Invalid SNACK" Reject reason code to "Invalid data ACK" since the invalid SNACK is already covered under "Protocol error". Also treating DataSN and R2TSN equivalently in this case. - Change in the SNACK section to require a Reject "Protocol error" on an invalid SNACK. - Time2Retain 0 in Logout Response indicates connection/session can‚ÇÖt recover - Coordinate DataSequenceInOrder with Error recovery level and MaxOutstandingR2T, also stating that only the last read/write sequence is recoverable under digest error recovery if DataSe- quenceInOrder=Yes - Alias designation format appendix is again out(!) - T10 has decided it will go in SPC3 - Task Management synchronization moved to the target (task man- agement response given after task management action and con- firmed delivery of all previous responses) - Removed the don‚ÇÖt care value in numerical negotiations - Changed Marker negotiation to allow it to be closed in one round - Marker position is not dependent of the length of the login phase - Statement made that reserved bits do not have to be checked at the beginning of Chapter 9 - InitialR2T, BidiInitialR2T and ImmediateData changed to LO - I bit (equivalent) in responses made 0 - Added a "double response" version for the ? key value to - ? value can be used only outside Login - added :, [ and ] as allowed in key values - allow 0 in LogoutLoginMax and Min - after task reassign no SNACK mandated, the function must be performed by target with information made available by reas- sign - removed the third party command section - SCSI now handles everything needed (including iSCSI aliasing) The following changes were made from draft-ietf-ips-iSCSI-08 to draft-ietf-ips-iSCSI-09: - Added Task management response "task management function not supported" - Negotiation (numeric) responder driven - Added vendor specific data to reject - Allow logout in discovery sessions - Variable DataPDULength - renamed MaxRecvPDULength - Key=value pairs can span PDU boundaries - Uniform treatment of text exchange resets Julian Satran Expires August 2002 6 11iSCSI.book Page 7 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Reintroduced DataACK as a special form of SNACK - Extended ISID in the Login Request - Removed 0 as a "no limit value" (residue from mode pages) - Reintroduced LogoutLoginMinTime - Digests moved to Operational Keys - Removed X bit in all commands and replaced it in Login and added a cleaning rule to CmdSN numbering - Several simplifications in state transition section - standard connection and session state diagrams are separately described for initiators and targets - Several minor technical and language changes in the error recovery section - Added Irrelevant to negotiations - Clarification to logout behavior - Clarification to command ordering - On SCSI timeout task abort instead of session failure - Changed version to 0x03 - ALL VERSION NUMBERS are temporary up to "Rafting" (take them with a grain of salt) The following changes were made from draft-ietf-ips-iSCSI-07 to draft-ietf-ips-iSCSI-08: - Clarified the use of initiator task tag with regard to the SCSI tag in Section 9.2.1.7 Initiator Task Tag - Added a clarification to Section 2.2.2.1 Command Numbering and Acknowledging - response to a command should not precede acknowledgment. - Added clarification to Section 9.7 SCSI Data-out & SCSI Data- in - good status in Data-In must be supported by initiators - Clarified InitiatorName is required at login in Section 4.3.1 Login Phase Start - Another clarification for SecurityContextComplete in Section 4.3.2 iSCSI Security Negotiation - Added "command not supported in this session type" to reject reasons - Discovery session implies MaxConnections = 1 - Second appearance of TargetAddress deleted - Padding forbidden for non-end-of-sequence data PDUs - Removed Boot and Copenhagener Session types - Changed explanation of ExpDataSN - Removed/corrected response 05 in Section 9.4.3 Response - Brought Section 2.2.7 Naming and Addressing in line with NDT draft - Fixed the syntax in accordance with [RFC2372] and [RFC2373] - Removed forgotten references to the default iSCSI target - Counters back to Reject Response - Clarification - SendTargets admissible only in full feature phase Julian Satran Expires August 2002 7 11iSCSI.book Page 8 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Changed name of DataOrder and DataDeliveryOrder to DataSequen- ceOrder and DataPDUInOrder and clarified appendix text - Padding bytes SHOULD be sent as 0 (instead of MUST be 0) - UA attention behavior for various resets deleted - replaced with reference to SAM2 - Removed AccessID - OpParmReset generalized - Clarified the definition of full-feature phase in Section 2.2.5 iSCSI Full Feature Phase - Added new Reject reason codes, tabular listing and a pointer to Section 9.14.3 Reason Code - Added additional Reject usage semantics on CmdSN and DataSN to Section 9.14.3 Reason Code - Added a new Logout Response code for failure - Renamed BUSY as RECOVERY_START, removed RECOVERY_DONE, and merged T11 and T14 transitions into T11-(1,2) in Section 5 State Transitions. - Corrected initiator handling of format errors - Clarified usage of command replay - Removed the delivery in same order as presented from Text Response - Clarified RefCmdSN function fro abort task - Corrected length field for AHS of type Extended CDB - Removed LUN from text management response - Clarified F bit for Bidirectional commands - Removed the Async iSCSI event "target reset" - Removed wording in Section 9.6 Task Management Function Response linking SCSI mode pages to Async Messages - Changed the ASC/ASCQ values to better mean "not enough unso- licited data" - Names examples include date - Removed references to S bit in Section 9.4 SCSI Response - Fixed NOP to simplify and avoid it consuming CmdSN - Fixed CRC and examples - Added the T, CSG & NSG fields to Login Command & Response, rewrote Chapter 3, changed all examples in Appendix C. - Login Phase Examples - to fit the above changes - Key=value confined to one response - Add command restart/replay to task management - Removed cryptographic digests - Removed "proxy required" status code - Re-named and fixed descriptions of status codes - Re-formatted login examples for clarity - SCSI/iSCSI parameters - fixed Section 3 SCSI Mode Parameters for iSCSI, out DataPDULength, DataSequenceOrder - Changed all sense keys to aborted command in the table in Sec- tion 9.4.2 Status - Rearranged requests to have all SCSI related grouped etc. - Fixed Task Management Function Request ABORT TASK and removed the part about it in Chapter 8. Julian Satran Expires August 2002 8 11iSCSI.book Page 9 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Reintroduced aliases (the data format) in an appendix. The aliasing mechanism once part of iSCSI is part of [SPC3] - Login negotiations - using only login request response (instead of former login and text) - F bit in login changed name to T bit - Stated defaults for mode parameters in chapter 3 - Updated Chapter 7 to reflect the current consensus on security - Changed all sense keys to aborted command in the table in 2.4.2 - Minor language clarifications in sections 1.2.3, 1.2.5, 1.2.6, 1.2.8. - Added a new Reject reason code "Task in progress" and clari- fied language in the same section. - Added more description to the session state transitions in Chapter 5. - Several changes in Chapter 6 corresponding to the new task management function "reassign". Other language changes in Chapter 6 for better description. Format errors are mandated to cause session failures. - Renamed the erstwhile error recovery levels as error recovery classes, and renamed "within-session" recovery to "connection recovery" to better reflect the mechanics. - Added Section 6.13 Error Recovery Hierarchy to define the error recovery hierarchy. - Modifications to error recovery algorithms in Appendix F. - Added a new Reject reason code "Invalid SNACK", added DataSN to Reject PDU. - Changed Section 9.17 Reject to use the "Invalid SNACK" reason code. - Removed a Logout reason code in Section 9.14 Logout Request to be consistent with Section 9.9 Asynchronous Message. - Collapsed the two event fields in Async Event and added vendor specific event - Immediate data can be negotiated anytime (consistency) - Removed replay as a protocol notion and all references to it - SNACK RunLength 0 means all - Cleaning the bookmark mechanism for text - New T10 approved ASC/ASQ codes - Added a incipient definitions section - thanks to Eddy Quick- sall - Change OpParmReset from Yes/No to default/current - Added Base64 to encode large strings - The 255 limit for key values is now "unless specified other- wise" - Cleaned SNACK format - Removed ExpR2TSN from SCSI command response it is too late - MaxBurstSize/FirstBurstSize back as key=value - Removed LogoutLoginMinTime (value provided in exchange) - Clear language on component function in generating ISID/TSID - Negotiation breaking is done through abort/reject Julian Satran Expires August 2002 9 11iSCSI.book Page 10 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Removed all iSCSI mode pages The following changes were made from draft-ietf-ips-iSCSI-06 to draft-ietf-ips-iSCSI-07: - Clarified the "fate" of immediate commands and resources man- dated (1.2.2.1) and introduced a reject-code for rejected immediate commands - Clarify CmdSN handling and checking order for ITT and CmdSN 1.2.2.1 - Added a statement to the effect that a receiver must be able to accept 0 length Data Segments to 2.7.6. Added also a state- ment to 2.2.1 that a zero-length data segment implies a zero- length digest - SCSI MODE SELECT will not really set the parameters (will not cause an error either). The parameters will be set exclusively with text mode and can be retrieved with either text or Mode- SENSE. This enables us to disable their change after the Login negotiation. Also added to the negotiation (1.2.4) the value "?" with special meaning of enquiry - Changed "task" to "command" wherever relevant - EMDP usage in line with other SCSI protocols. EMDP governs how a target may request data and deliver. Similar to FCP a sepa- rate (protocol) parameter governs data PDU ordering within Sequence (DataPDUInOrder). Cleaned wording of DataOrder. Fixed final bit to define sequences in input stream. - Added a "persistent state" part (1.2.8) - Some Task Management commands may require authorization or may not be implemented. If not authorized they will return as if executed with a qualifier indicating "not authorized" or "not implemented" (clear LU and the resets) - Task management commands and responses are "generalized" to all iSCSI tagged commands (they are named now Task Management command and response). Their behavior with respect to their CmdSN is clarified and mandated - The logic to update ExpCmdSN etc. moved to 1.2.2.1 - Explicitly specified that a target can "initiate" negotiating a parameter (offering)(1.2.4) - Returned the "direction" bit and a set of codes similar to version 05 - Introduced a "special" session type (CopyManagerSession) to be used between a Copy Manager and all of its target; it may help define authentication and limit the type f commands to be exe- cuted in such a session - Added 8.4 - How to Abort Safely a Command that Was Not Received - Fixed the Logout Text - AHSLength is now the first field in the AHS Julian Satran Expires August 2002 10 11iSCSI.book Page 11 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Fixed wording in 2.35 indicating AHS is mandatory for Bi- directional commands - All key=value responses have to be explicit (none, not-under- stood etc.); no more selection by hiatus - Targets can also offer key=value pairs (i.e., initiate negoti- ation) stated explicitly in 2.9.3 - Logout has a CmdSN field - The Status SNACK can be discarded if the target has no such recovery - Some parameters have been removed and replaced by "reasonable" defaults (read arbitrary defaults!); many others can't be changed anymore while the session is in full-feature phase - NOP-Out specifies how LUN is generated when used (copied from NOP-In) - Initial Marker-Less Interval is not a parameter anymore - A response with F=1 during negotiation may not contain key=value pairs that may require additional answers from the initiator - Clarified the meaning of the F bit on Write commands with regard to immediate and unsolicited data; F bit 0 means that unsolicited data will follow while F bit 1 means that this is the last of them (if any) - You can have both immediate and unsolicited Data-Out PDUs - DataPDULength and FirstBurstSize of 0 are allowed and mean unlimited length - Task management command behavior relative to their own CmdSN is now stated in no uncertain terms (they are mandated to exe- cute as if issued at CmdSN and, in case of aborts and clear/ reset no additional response/status is expected for those com- mands after the task management command response - DataSN field in R2T renamed as R2TSN (better reflects seman- tics) and SNACK explicitly says that it requests Data or R2T. - A session can have only one outstanding text request (not sequence) - Text for Login Response 0301 changed (removed the maintenance mention) - Clarified when ExpDataSN is reserved in SCSI Response - Clarified the text and parameter (timers) for iSCSI event - Padding bytes should be 0 (2.1) - TotalAHSLength in 2.1.1.1 includes padding - DataSegmentLength in 2.1.1.2 excludes padding - Clarified bits in AHS type - Limit for key/value string lengths (63, 255) in 2.8.3 - Added an example of SCSI event to Asynchronous Message - Changed "Who" to "Who can send" in appendix - Clarified meaning of parameters on 2.18.1 - Asynchronous Mes- sage - iSCSI Event - Clarified the required initiator behavior at logout (not send- ing other commands) and how one expects the TCP close to be performed in 2.14 Julian Satran Expires August 2002 11 11iSCSI.book Page 12 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Added a Login Response code indicating that a session can't include a given connection (0208) - Clarified transition to full feature phase (per session and per connection and the role of the leading connection) in 1.2.5 - Corrected "one outstanding text request per connection" instead of "per session" - For the Login Response TSID must be valid only if Login is accepted and the F bit is 1 - Added examples illustrating DataSN and R2TSN (from Eddy Quick- sall) - Added more text to the task management command 2.5 - Removed EnableACA and its dependents (in task management) and stated the requirement for a Unit Attention conform to SAM2 - iSCSI Target Name if used on a connection other than the first must be the same as on the first (4.1) - Fixed the examples in the Login appendix to correspond to the new keys - Fixed SCSI Response Flags and made them consistent with the Data-In PDU - All specified keys except X-* MUST be accepted (2.8.3) - Hexadecimal notation is 0xab123cd (not 0x'ab123cd') - Clarified CmdSN usage in immediate commands and the meaning of "execution engine" in 1.2.2.1 - Reject response that prevent the creation of a SCSI task or result in a SCSI task being terminated must be followed by a SCSI Response with a Check Condition status 2.19.1 - Additional Runs (AddRuns) dropped from the SNACK request (too complex). With it disappeared also the implicit acknowledge- ment of sequences "between runs" - PDUs delivered because of SNACK will be exact replicas of the original PDUs (including all flags) 2.16 - Added CommandReplaySupport key to negotiate support for full command replay (a command can be replayed after the status has been issued but has not been acknowledged) and a reject cause of unsupported command reply - Added CommandFailoverSupport key to negotiate support for com- mand allegiance change (command retry on another connection) - Status SNACK for an acknowledged status is a protocol error (cause for reject) - Reject cause "Command In Progress" when requesting replay before status is issued and while command is running - Premature SNACKs are silently discarded (2.16) - Status SNACK has to supported only if within command or within connection recovery is supported. If within session recovery is supported SNACK can be discarded and followed by an Async. Message requesting logout - StatSN added to Logout Response - Added "CID not found" to Logout Response reason codes Julian Satran Expires August 2002 12 11iSCSI.book Page 13 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - Async Message - iSCSI event 2 (request logout) has to be sent on the connection to be dropped. Wording fixed. - Naming changes - iqn (stands for iSCSI qualified name) intro- duced as a replacement to fqn. Iqn prefixes also reversed names - text in 8.3 revised (task management implementation mechanism) - Fixed bit 7 byte 1 in Task Management response to 1 (consis- tency) - Clarified in 1.2.2 behavior when "command window" is 0 (MaxC- mdSN = ExpCmdSN -1) - Added state transitions part (new part 6) - Refreshed recovery chapter (new part 7) - Added an appendix with detailed recovery mechanisms (Appendix E) - Added session types a brief explanation in part 1 - Added DiscoverySession key and SendTargets appendix - SCSI response made to fit having both a Status and a Response field. Needed for target errors that result in a check condi- tion and ACA. In line with SAM2 that requires both fields (former versions where modeled on FCP). - The security appendix list SRP as mandatory to implement - Clarified initial CmdSN and the role of TSID as a serializer - Long Text Responses - additional fields added to the text request and text response - Added a SCSI to iSCSI concept mapping section 1.5 - Clarified SNACK wording to indicate that in general command. Request, iSCSI command and iSCSI command have the same mean- ing. Also status, response or numbered response. - Changed InitStatSN and clarified how it increases - Added requirement for a 0x00 delimiter after each key=value - Added binary negotiations (Yes|No) explicitly to 1.2.4 - All keys and values in the spec are case sensitive (stated in the text request) - Changed the "operational parameters sent before the security. MAY be discarded" into MUST be discarded - Changed the login reject 0201 to read - Security Negotiation Failed - Added to 2.3.1 a paragraph about mandatory consistencies - Stated clearly that F bit pairing is "local" (per/pair) and not per negotiation - Clarified dependent parameter status - Added CRC Example - Added OpParmReset=Yes - SecurityContextComplete is mandatory if any option offered - Added a warning about the implications of not sending all unsolicited data to part 8 - Added a recommendation to send unsolicited data at FirstBurst- Size and a response (error) for targets not supporting less - Many more minor editorial changes, clarifications, typos etc. - Responses in same position in SCSI response, logout, task etc. Julian Satran Expires August 2002 13 11iSCSI.book Page 14 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Table of Contents Julian Satran Expires August 2002 14 11iSCSI.book Page 15 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Status of this Memo . . . . . . . . . . . . . . . . . . . . . . . . . 2 Abstract . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Conventions used in this document . . . . . . . . . . . . . . . . . . 3 Change Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .22 2. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 2.1 SCSI Concepts . . . . . . . . . . . . . . . . . . . . . . . . .26 2.2 iSCSI Concepts and Functional Overview . . . . . . . . . . . .27 2.2.1 Layers and Sessions . . . . . . . . . . . . . . . . . . .27 2.2.2 Ordering and iSCSI Numbering . . . . . . . . . . . . . . .28 2.2.2.1 Command Numbering and Acknowledging . . . . . . . . .29 2.2.2.2 Response/Status Numbering and Acknowledging . . . . .32 2.2.2.3 Data Sequencing . . . . . . . . . . . . . . . . . . .32 2.2.3 iSCSI Login . . . . . . . . . . . . . . . . . . . . . . .33 2.2.4 iSCSI Full Feature Phase . . . . . . . . . . . . . . . . .34 2.2.5 iSCSI Connection Termination . . . . . . . . . . . . . . .36 2.2.6 Naming and Addressing . . . . . . . . . . . . . . . . . .37 2.2.7 Persistent State . . . . . . . . . . . . . . . . . . . . .39 2.2.8 Message Synchronization and Steering . . . . . . . . . . .39 2.2.8.1 Rationale . . . . . . . . . . . . . . . . . . . . . .39 2.2.8.2 Synchronization (sync) and Steering Functional Model 40 2.2.8.3 Sync and Steering and Other Encapsulation Layers . .42 2.2.8.4 Sync/Steering and iSCSI PDU Size . . . . . . . . . .43 2.3 iSCSI Session Types . . . . . . . . . . . . . . . . . . . . . .44 2.4 SCSI to iSCSI Concepts Mapping Model . . . . . . . . . . . . .44 2.4.1 iSCSI Architecture Model . . . . . . . . . . . . . . . . .45 2.4.2 SCSI Architecture Model . . . . . . . . . . . . . . . . .47 2.4.3 Consequences of the Model . . . . . . . . . . . . . . . .49 2.4.3.1 I_T Nexus State . . . . . . . . . . . . . . . . . . .50 2.4.3.2 SCSI Mode Pages . . . . . . . . . . . . . . . . . . .50 2.5 Request/Response Summary . . . . . . . . . . . . . . . . . . .51 2.5.1 Request/Response types carrying SCSI payload . . . . . . .51 2.5.1.1 SCSI-Command . . . . . . . . . . . . . . . . . . . .51 2.5.1.2 SCSI-Response . . . . . . . . . . . . . . . . . . . .51 2.5.1.3 Task Management Function Request . . . . . . . . . .52 2.5.1.4 Task Management Function Response . . . . . . . . . .53 2.5.1.5 SCSI Data-out and SCSI Data-in . . . . . . . . . . .53 2.5.1.6 Ready To Transfer (R2T) . . . . . . . . . . . . . . .54 2.5.2 Requests/Responses carrying SCSI and iSCSI Payload . . . .54 2.5.2.1 Asynchronous Message . . . . . . . . . . . . . . . .54 2.5.3 Requests/Responses carrying iSCSI Only Payload . . . . . .54 2.5.3.1 Text Request and Text Response . . . . . . . . . . .54 Julian Satran Expires August 2002 15 11iSCSI.book Page 16 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 2.5.3.2 Login Request and Login Response . . . . . . . . . .55 2.5.3.3 Logout Request and Response . . . . . . . . . . . . .56 2.5.3.4 SNACK Request . . . . . . . . . . . . . . . . . . .56 2.5.3.5 Reject . . . . . . . . . . . . . . . . . . . . . . .57 2.5.3.6 NOP-Out Request and NOP-In Response . . . . . . . . .57 3. SCSI Mode Parameters for iSCSI . . . . . . . . . . . . . . . . . .58 4. Login and Full Feature Phase Negotiation . . . . . . . . . . . . .59 4.1 Text Format . . . . . . . . . . . . . . . . . . . . . . . . . .59 4.2 Text Mode Negotiation . . . . . . . . . . . . . . . . . . . . .59 4.3 Login Phase . . . . . . . . . . . . . . . . . . . . . . . . . .62 4.3.1 Login Phase Start . . . . . . . . . . . . . . . . . . . .64 4.3.2 iSCSI Security Negotiation . . . . . . . . . . . . . . . .65 4.3.3 Operational Parameter Negotiation During the Login Phase .66 4.3.4 Connection reinstatement . . . . . . . . . . . . . . . . .67 4.3.5 Session reinstatement . . . . . . . . . . . . . . . . . .68 4.3.6 Session Continuation, closure and failure . . . . . . . .68 4.4 Operational Parameter Negotiation Outside the Login Phase . . .68 5. State Transitions . . . . . . . . . . . . . . . . . . . . . . . .70 5.1 Standard Connection State Diagrams . . . . . . . . . . . . . .70 5.1.1 Standard Connection State Diagram for an Initiator . . . .70 5.1.2 Standard Connection State Diagram for a Target . . . . . .72 5.1.3 State Descriptions for Initiators and Targets . . . . . .74 5.1.4 State Transition Descriptions for Initiators and Targets .75 5.2 Connection Cleanup State Diagram for Initiators and Targets . .78 5.2.1 State Descriptions for Initiators and Targets . . . . . .80 5.2.2 State Transition Descriptions for Initiators and Targets .81 5.3 Session State Diagrams . . . . . . . . . . . . . . . . . . . .82 5.3.1 Session State Diagram for a Target . . . . . . . . . . . .83 5.3.2 State Descriptions for Initiators and Targets . . . . . .84 5.3.3 State Transition Descriptions for Initiators and Targets .85 6. iSCSI Error Handling and Recovery . . . . . . . . . . . . . . . .87 6.1 Retry and Reassign in Recovery . . . . . . . . . . . . . . . .87 6.1.1 Usage of Retry . . . . . . . . . . . . . . . . . . . . . .87 6.1.2 Allegiance Reassignment . . . . . . . . . . . . . . . . .88 6.2 Usage Of Reject PDU in Recovery . . . . . . . . . . . . . . . .89 6.3 Connection timeout management . . . . . . . . . . . . . . . . .89 6.3.1 Timeouts on transport exception events . . . . . . . . . .89 6.3.2 Timeouts on planned decommissioning . . . . . . . . . . .90 6.4 Format Errors . . . . . . . . . . . . . . . . . . . . . . . . .90 6.5 Digest Errors . . . . . . . . . . . . . . . . . . . . . . . . .90 6.6 Sequence Errors . . . . . . . . . . . . . . . . . . . . . . . .92 6.7 SCSI Timeouts . . . . . . . . . . . . . . . . . . . . . . . . .92 6.8 Negotiation Failures . . . . . . . . . . . . . . . . . . . . .93 Julian Satran Expires August 2002 16 11iSCSI.book Page 17 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 6.9 Protocol Errors . . . . . . . . . . . . . . . . . . . . . . . .94 6.10 Connection Failures . . . . . . . . . . . . . . . . . . . . .94 6.11 Session Errors . . . . . . . . . . . . . . . . . . . . . . . .95 6.12 Recovery Classes . . . . . . . . . . . . . . . . . . . . . . .95 6.12.1 Recovery Within-command . . . . . . . . . . . . . . . . .96 6.12.2 Recovery Within-connection . . . . . . . . . . . . . . .97 6.12.3 Connection Recovery . . . . . . . . . . . . . . . . . . .97 6.12.4 Session Recovery . . . . . . . . . . . . . . . . . . . .98 6.13 Error Recovery Hierarchy . . . . . . . . . . . . . . . . . . .99 7. Security Considerations . . . . . . . . . . . . . . . . . . . . 101 7.1 iSCSI Security Mechanisms . . . . . . . . . . . . . . . . . . 101 7.2 In-band Initiator-Target Authentication . . . . . . . . . . . 102 7.3 IPsec . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 7.3.1 Data Integrity and Authentication . . . . . . . . . . . 103 7.3.2 Confidentiality . . . . . . . . . . . . . . . . . . . . 103 7.3.3 Policy, Security Associations and Key Management . . . . 104 8. Notes to Implementers . . . . . . . . . . . . . . . . . . . . . 106 8.1 Multiple Network Adapters . . . . . . . . . . . . . . . . . . 106 8.1.1 Conservative Reuse of ISIDs . . . . . . . . . . . . . . 106 8.1.2 iSCSI Name and ISID/TSID Use . . . . . . . . . . . . . . 107 8.2 Autosense and Auto Contingent Allegiance (ACA) . . . . . . . 108 8.3 Command Retry and Cleaning Old Command Instances . . . . . . 109 8.4 Synch and Steering Layer and Performance . . . . . . . . . . 109 8.5 Unsolicited Data and Performance . . . . . . . . . . . . . . 109 8.6 Considerations for State-dependent devices . . . . . . . . . 110 8.6.1 Determining the proper ErrorRecoveryLevel . . . . . . . 110 9. iSCSI PDU Formats . . . . . . . . . . . . . . . . . . . . . . . 112 9.1 iSCSI PDU Length and Padding . . . . . . . . . . . . . . . . 112 9.2 PDU Template, Header, and Opcodes . . . . . . . . . . . . . . 112 9.2.1 Basic Header Segment (BHS) . . . . . . . . . . . . . . . 113 9.2.1.1 I . . . . . . . . . . . . . . . . . . . . . . . . . 114 9.2.1.2 Opcode . . . . . . . . . . . . . . . . . . . . . . 114 9.2.1.3 Opcode-specific Fields . . . . . . . . . . . . . . 115 9.2.1.4 TotalAHSLength . . . . . . . . . . . . . . . . . . 115 9.2.1.5 DataSegmentLength . . . . . . . . . . . . . . . . . 115 9.2.1.6 LUN . . . . . . . . . . . . . . . . . . . . . . . . 115 9.2.1.7 Initiator Task Tag . . . . . . . . . . . . . . . . 116 9.2.2 Additional Header Segment (AHS) . . . . . . . . . . . . 116 9.2.2.1 AHSType . . . . . . . . . . . . . . . . . . . . . . 116 9.2.2.2 AHSLength . . . . . . . . . . . . . . . . . . . . . 117 9.2.2.3 Extended CDB AHS . . . . . . . . . . . . . . . . . 117 9.2.2.4 Bidirectional Expected Read-Data Length AHS . . . . 117 9.2.3 Header Digest and Data Digest . . . . . . . . . . . . . 117 Julian Satran Expires August 2002 17 11iSCSI.book Page 18 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.2.4 Data Segment . . . . . . . . . . . . . . . . . . . . . . 118 9.3 SCSI Command . . . . . . . . . . . . . . . . . . . . . . . . . 119 9.3.1 Flags and Task Attributes (byte 1) . . . . . . . . . . . 119 9.3.2 CRN . . . . . . . . . . . . . . . . . . . . . . . . . . 120 9.3.3 CmdSN - Command Sequence Number . . . . . . . . . . . . 120 9.3.4 ExpStatSN . . . . . . . . . . . . . . . . . . . . . . . 120 9.3.5 Expected Data Transfer Length . . . . . . . . . . . . . 120 9.3.6 CDB - SCSI Command Descriptor Block . . . . . . . . . . 121 9.3.7 Data Segment - Command Data . . . . . . . . . . . . . . 121 9.4 SCSI Response . . . . . . . . . . . . . . . . . . . . . . . . 122 9.4.1 Flags (byte 1) . . . . . . . . . . . . . . . . . . . . . 122 9.4.2 Status . . . . . . . . . . . . . . . . . . . . . . . . . 123 9.4.3 Response . . . . . . . . . . . . . . . . . . . . . . . . 124 9.4.4 Residual Count . . . . . . . . . . . . . . . . . . . . . 125 9.4.5 Bidirectional Read Residual Count . . . . . . . . . . . 125 9.4.6 Data Segment - Sense and Response Data Segment . . . . . 125 9.4.6.1 SenseLength . . . . . . . . . . . . . . . . . . . . 126 9.4.7 ExpDataSN . . . . . . . . . . . . . . . . . . . . . . . 126 9.4.8 StatSN - Status Sequence Number . . . . . . . . . . . . 126 9.4.9 ExpCmdSN - Next Expected CmdSN from this Initiator . . . 126 9.4.10 MaxCmdSN - Maximum CmdSN from this Initiator . . . . . 127 9.5 Task Management Function Request . . . . . . . . . . . . . . . 128 9.5.1 Function . . . . . . . . . . . . . . . . . . . . . . . . 128 9.5.2 LUN . . . . . . . . . . . . . . . . . . . . . . . . . . 131 9.5.3 Referenced Task Tag . . . . . . . . . . . . . . . . . . 131 9.5.4 RefCmdSN or ExpDataSN . . . . . . . . . . . . . . . . . 131 9.6 Task Management Function Response . . . . . . . . . . . . . . 132 9.6.1 Response . . . . . . . . . . . . . . . . . . . . . . . . 132 9.6.2 Referenced Task Tag . . . . . . . . . . . . . . . . . . 133 9.6.3 Task Management actions on task sets . . . . . . . . . . 133 9.7 SCSI Data-out & SCSI Data-in . . . . . . . . . . . . . . . . . 135 9.7.1 F (Final) Bit . . . . . . . . . . . . . . . . . . . . . 137 9.7.2 A (Acknowledge) bit . . . . . . . . . . . . . . . . . . 137 9.7.3 Target Transfer Tag . . . . . . . . . . . . . . . . . . 137 9.7.4 StatSN . . . . . . . . . . . . . . . . . . . . . . . . . 138 9.7.5 DataSN . . . . . . . . . . . . . . . . . . . . . . . . . 138 9.7.6 Buffer Offset . . . . . . . . . . . . . . . . . . . . . 138 9.7.7 DataSegmentLength . . . . . . . . . . . . . . . . . . . 138 9.7.8 Flags (byte 1) . . . . . . . . . . . . . . . . . . . . . 139 9.8 Ready To Transfer (R2T) . . . . . . . . . . . . . . . . . . . 140 9.8.1 R2TSN . . . . . . . . . . . . . . . . . . . . . . . . . 141 9.8.2 StatSN . . . . . . . . . . . . . . . . . . . . . . . . . 141 9.8.3 Desired Data Transfer Length and Buffer Offset . . . . . 141 Julian Satran Expires August 2002 18 11iSCSI.book Page 19 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.8.4 Target Transfer Tag . . . . . . . . . . . . . . . . . . 142 9.9 Asynchronous Message . . . . . . . . . . . . . . . . . . . . . 143 9.9.1 AsyncEvent . . . . . . . . . . . . . . . . . . . . . . . 144 9.9.2 AsyncVCode . . . . . . . . . . . . . . . . . . . . . . . 145 9.9.3 Sense Data or iSCSI Event Data . . . . . . . . . . . . . 145 9.10 Text Request . . . . . . . . . . . . . . . . . . . . . . . . 146 9.10.1 F (Final) Bit . . . . . . . . . . . . . . . . . . . . . 146 9.10.2 Initiator Task Tag . . . . . . . . . . . . . . . . . . 147 9.10.3 Target Transfer Tag . . . . . . . . . . . . . . . . . . 147 9.10.4 Text . . . . . . . . . . . . . . . . . . . . . . . . . 148 9.11 Text Response . . . . . . . . . . . . . . . . . . . . . . . . 149 9.11.1 F (Final) Bit . . . . . . . . . . . . . . . . . . . . . 149 9.11.2 Initiator Task Tag . . . . . . . . . . . . . . . . . . 150 9.11.3 Target Transfer Tag . . . . . . . . . . . . . . . . . . 150 9.11.4 Text Response Data . . . . . . . . . . . . . . . . . . 151 9.12 Login Request . . . . . . . . . . . . . . . . . . . . . . . . 152 9.12.1 T (Transit) Bit . . . . . . . . . . . . . . . . . . . . 152 9.12.2 CSG and NSG . . . . . . . . . . . . . . . . . . . . . . 153 9.12.3 Version-max . . . . . . . . . . . . . . . . . . . . . . 153 9.12.4 Version-min . . . . . . . . . . . . . . . . . . . . . . 153 9.12.5 ISID . . . . . . . . . . . . . . . . . . . . . . . . . 153 9.12.6 TSID . . . . . . . . . . . . . . . . . . . . . . . . . 155 9.12.7 Connection ID - CID . . . . . . . . . . . . . . . . . . 155 9.12.8 CmdSN . . . . . . . . . . . . . . . . . . . . . . . . . 155 9.12.9 ExpStatSN . . . . . . . . . . . . . . . . . . . . . . . 156 9.12.10 Login Parameters . . . . . . . . . . . . . . . . . . . 156 9.13 Login Response . . . . . . . . . . . . . . . . . . . . . . . 157 9.13.1 Version-max . . . . . . . . . . . . . . . . . . . . . . 157 9.13.2 Version-active . . . . . . . . . . . . . . . . . . . . 158 9.13.3 TSID . . . . . . . . . . . . . . . . . . . . . . . . . 158 9.13.4 StatSN . . . . . . . . . . . . . . . . . . . . . . . . 158 9.13.5 Status-Class and Status-Detail . . . . . . . . . . . . 158 9.13.6 T (Transit) bit . . . . . . . . . . . . . . . . . . . . 161 9.14 Logout Request . . . . . . . . . . . . . . . . . . . . . . . 162 9.14.1 CID . . . . . . . . . . . . . . . . . . . . . . . . . . 163 9.14.2 ExpStatSN . . . . . . . . . . . . . . . . . . . . . . . 163 9.14.3 Reason Code . . . . . . . . . . . . . . . . . . . . . . 164 9.15 Logout Response . . . . . . . . . . . . . . . . . . . . . . . 165 9.15.1 Response . . . . . . . . . . . . . . . . . . . . . . . 165 9.15.2 Time2Wait . . . . . . . . . . . . . . . . . . . . . . . 166 9.15.3 Time2Retain . . . . . . . . . . . . . . . . . . . . . . 166 9.16 SNACK Request . . . . . . . . . . . . . . . . . . . . . . . 168 9.16.1 Type . . . . . . . . . . . . . . . . . . . . . . . . . 169 Julian Satran Expires August 2002 19 11iSCSI.book Page 20 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.16.2 BegRun . . . . . . . . . . . . . . . . . . . . . . . . 170 9.16.3 RunLength . . . . . . . . . . . . . . . . . . . . . . . 170 9.17 Reject . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 9.17.1 Reason . . . . . . . . . . . . . . . . . . . . . . . . 172 9.17.2 DataSN . . . . . . . . . . . . . . . . . . . . . . . . 173 9.17.3 StatSN, ExpCmdSN and MaxCmdSN . . . . . . . . . . . . . 173 9.17.4 Complete Header of Bad PDU . . . . . . . . . . . . . . 173 9.18 NOP-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 9.18.1 Initiator Task Tag . . . . . . . . . . . . . . . . . . 175 9.18.2 Target Transfer Tag . . . . . . . . . . . . . . . . . . 175 9.18.3 Ping Data . . . . . . . . . . . . . . . . . . . . . . . 175 9.19 NOP-In . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 9.19.1 Target Transfer Tag . . . . . . . . . . . . . . . . . . 177 9.19.2 LUN . . . . . . . . . . . . . . . . . . . . . . . . . . 177 10. iSCSI Security Keys and Values . . . . . . . . . . . . . . . . 178 10.1 AuthMethod . . . . . . . . . . . . . . . . . . . . . . . . . 178 10.2 Kerberos . . . . . . . . . . . . . . . . . . . . . . . . . . 179 10.3 Simple Public-Key Mechanism (SPKM) . . . . . . . . . . . . . 180 10.4 Secure Remote Password (SRP) . . . . . . . . . . . . . . . . 181 10.5 Challenge Handshake Authentication Protocol (CHAP) . . . . . 182 11. Login/Text Operational Keys . . . . . . . . . . . . . . . . . . 184 11.1 HeaderDigest and DataDigest . . . . . . . . . . . . . . . . 184 11.2 MaxConnections . . . . . . . . . . . . . . . . . . . . . . . 186 11.3 SendTargets . . . . . . . . . . . . . . . . . . . . . . . . 186 11.4 TargetName . . . . . . . . . . . . . . . . . . . . . . . . . 186 11.5 InitiatorName . . . . . . . . . . . . . . . . . . . . . . . 187 11.6 TargetAlias . . . . . . . . . . . . . . . . . . . . . . . . 187 11.7 InitiatorAlias . . . . . . . . . . . . . . . . . . . . . . . 188 11.8 TargetAddress . . . . . . . . . . . . . . . . . . . . . . . 188 11.9 InitialR2T . . . . . . . . . . . . . . . . . . . . . . . . . 189 11.10 BidiInitialR2T . . . . . . . . . . . . . . . . . . . . . . 189 11.11 ImmediateData . . . . . . . . . . . . . . . . . . . . . . . 190 11.12 MaxRecvPDULength . . . . . . . . . . . . . . . . . . . . . 191 11.13 MaxBurstSize . . . . . . . . . . . . . . . . . . . . . . . 191 11.14 FirstBurstSize . . . . . . . . . . . . . . . . . . . . . . 192 11.15 DefaultTime2Wait . . . . . . . . . . . . . . . . . . . . . 192 11.16 DefaultTime2Retain . . . . . . . . . . . . . . . . . . . . 193 11.17 MaxOutstandingR2T . . . . . . . . . . . . . . . . . . . . . 193 11.18 DataPDUInOrder . . . . . . . . . . . . . . . . . . . . . . 194 11.19 DataSequenceInOrder . . . . . . . . . . . . . . . . . . . . 194 11.20 ErrorRecoveryLevel . . . . . . . . . . . . . . . . . . . . 195 11.21 SessionType . . . . . . . . . . . . . . . . . . . . . . . . 195 11.22 The Vendor Specific Key Format . . . . . . . . . . . . . . 196 Julian Satran Expires August 2002 20 11iSCSI.book Page 21 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 197 References and Bibliography . . . . . . . . . . . . . . . . . . . . 198 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 199 Appendix A. Sync and Steering with Fixed Interval Markers . . . . . 202 A.1 Markers At Fixed Intervals . . . . . . . . . . . . . . . . . 202 A.2 Initial Marker-less Interval . . . . . . . . . . . . . . . . 203 A.3 Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . 203 A.3.1 OFMarker, IFMarker . . . . . . . . . . . . . . . . . . . 203 A.3.2 OFMarkInt, IFMarkInt . . . . . . . . . . . . . . . . . . 204 Appendix B. Examples . . . . . . . . . . . . . . . . . . . . . . . 206 B.4 Read Operation Example . . . . . . . . . . . . . . . . . . . 206 B.5 Write Operation Example . . . . . . . . . . . . . . . . . . . 207 B.6 R2TSN/DataSN use Examples . . . . . . . . . . . . . . . . . . 207 B.7 CRC Examples . . . . . . . . . . . . . . . . . . . . . . . . 211 Appendix C. Login Phase Examples . . . . . . . . . . . . . . . . . 213 Appendix D. SendTargets Operation . . . . . . . . . . . . . . . . . 222 Appendix E. Algorithmic Presentation of Error Recovery Classes . . 226 E.8 General Data Structure and Procedure Description . . . . . . 226 E.9 Within-command Error Recovery Algorithms . . . . . . . . . . 227 E.9.1 Procedure Descriptions . . . . . . . . . . . . . . . . . 227 E.9.2 Initiator Algorithms . . . . . . . . . . . . . . . . . . 228 E.9.3 Target Algorithms . . . . . . . . . . . . . . . . . . . 230 E.10 Within-connection Recovery Algorithms . . . . . . . . . . . 232 E.10.1 Procedure Descriptions . . . . . . . . . . . . . . . . 232 E.10.1.1 Initiator Algorithms . . . . . . . . . . . . . . . 233 E.10.1.2 Target Algorithms . . . . . . . . . . . . . . . . 235 E.10.2 Connection Recovery Algorithms . . . . . . . . . . . . 236 E.10.2.1 Procedure Descriptions . . . . . . . . . . . . . . 236 E.10.2.2 Initiator Algorithms . . . . . . . . . . . . . . . 237 E.10.2.3 Target Algorithms . . . . . . . . . . . . . . . . 239 Appendix F. Clearing effects on various events on targets . . . . . 241 Full Copyright Statement . . . . . . . . . . . . . . . . . . . . . 247 Julian Satran Expires August 2002 21 11iSCSI.book Page 22 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 1. Definitions - Alias: An alias string could also be associated with an iSCSI Node. The alias allows an organization to associate a user-friendly string with the iSCSI Name. However, the alias string is not a substitute for the iSCSI Name. - CID (Connection ID): Connections within a session are identified by a connection ID. It is a unique ID for this connection within the ses- sion for the initiator. It is generated by the initiator and presented to the target during login requests and during logouts that close con- nections. - Connection: Communication between the initiator and target occurs over one or more TCP connections. The TCP connections carry control messages, SCSI commands, parameters, and data within iSCSI Protocol Data Units (iSCSI PDUs). - iSCSI Initiator Name: The iSCSI Initiator Name specifies the world- wide unique name of the initiator. - iSCSI Initiator Node: The "initiator". - iSCSI Layer: This layer builds/receives iSCSI PDUs and relays/ receives them to/from one or more TCP connections that form an initi- ator-target "session". - iSCSI Name: The name of an iSCSI initiator or iSCSI target. - iSCSI Node: The iSCSI Node represents a single iSCSI initiator or iSCSI target. There are one or more iSCSI Nodes within a Network Entity. The iSCSI Node is accessible via one or more Network Portals. An iSCSI Node is identified by its iSCSI Name. The separation of the iSCSI Name from the addresses used by and for the iSCSI node allows multiple iSCSI nodes to use the same addresses, and the same iSCSI node to use multiple addresses. iSCSI nodes also have addresses. An iSCSI address specifies a single path to an iSCSI node. - iSCSI Target Name: The iSCSI Target Name specifies the worldwide unique name of the target. - iSCSI Target Node: The "target". Julian Satran Expires August 2002 22 11iSCSI.book Page 23 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - iSCSI Task: An iSCSI task is an iSCSI request for which a response is expected. - iSCSI Transfer Direction: The iSCSI transfer direction is defined with regard to the initiator. Outbound or outgoing transfers are transfers from the initiator to the target, while inbound or incoming transfers are from the target to the initiator. - I_T nexus: According to [SAM2], the I_T nexus is a relationship between a SCSI Initiator Port and a SCSI Target Port. For iSCSI, this relationship is a session, defined as a relationship between an iSCSI Initiator's end of session (SCSI Initiator Port) and the iSCSI Tar- get's Portal Group. The I_T nexus can be identified by the conjunction of the SCSI port names; that is, the I_T nexus identifier is the tuple (iSCSI Initiator Name + 'i'+ ISID, iSCSI Target Name + 't'+ Portal Group Tag). NOTE: The I_T nexus identifier is not equal to the session identifier (SSID). - Network Entity: The Network Entity represents a device or gateway that is accessible from the IP network. A Network Entity must have one or more Network Portals, each of which can be used to gain access to the IP network by some iSCSI Nodes contained in that Network Entity. - Network Portal: The Network Portal is a component of a Network Entity that has a TCP/IP network address and that may be used by an iSCSI Node within that Network Entity for the connection(s) within one of its iSCSI sessions. A Network Portal in an initiator is identified by its IP address. A Network Portal in a target is identified by its IP address and its listening TCP port. - Originator - in a negotiation or exchange the party that initiates the negotiation or exchange. - PDU (Protocol Data Unit): The initiator and target divide their com- munications into messages. The term "iSCSI protocol data unit" (iSCSI PDU) is used for these messages. - Portal Groups: iSCSI supports multiple connections within the same session; some implementations will have the ability to combine con- nections in a session across multiple Network Portals. A Portal Group defines a set of Network Portals within an iSCSI Node that collec- tively supports the capability of coordinating a session with connec- Julian Satran Expires August 2002 23 11iSCSI.book Page 24 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 tions spanning these portals. Not all Network Portals within a Portal Group need participate in every session connected through that Portal Group. One or more Portal Groups may provide access to an iSCSI Node. Each Network Portal as utilized by a given iSCSI Node belongs to exactly one portal group within that node. - Portal Group Tag: This simple integer value between 1 and 65535 identifies the Portal Group within an iSCSI Node. All Network Portals with the same portal group tag in the context of a given iSCSI Node are in the same Portal Group. - Responder: In a negotiation or exchange, the party that responds to the originator of the negotiation or exchange. - SCSI Device: This is the SAM2 term for an entity that contains other SCSI entities. For example, a SCSI Initiator Device contains one or more SCSI Initiator Ports and zero or more application clients; a SCSI Target Device contains one or more SCSI Target Ports and one or more logical units. For iSCSI, the SCSI Device is the component within an iSCSI Node that provides the SCSI functionality. As such, there can be at most one SCSI Device within a given iSCSI Node. Access to the SCSI Device can only be achieved in an iSCSI normal operational session. The SCSI Device Name is defined to be the iSCSI Name of the node and its use is mandatory in the iSCSI protocol. - SCSI Layer: This builds/receives SCSI CDBs (Command Descriptor Blocks) and relays/receives them with the remaining command execute parameters to/from the iSCSI Layer. - Session: The group of TCP connections that link an initiator with a target, form a session (loosely equivalent to a SCSI I-T nexus). TCP connections can be added and removed from a session. Across all con- nections within a session, an initiator sees one "target image". - SSID (Session ID): A session is defined by a session ID that is com- posed of an initiator part (ISID) and a target part (TSID). - SCSI Initiator Port: This maps to the endpoint of an iSCSI normal operational session. An iSCSI normal operational session is negoti- ated through the login process between an iSCSI initiator node and an iSCSI target node. At successful completion of this process, a SCSI Initiator Port is created within the SCSI Initiator Device. The SCSI Initiator Port Name and SCSI Initiator Port Identifier are both defined to be the iSCSI Initiator Name together with (a) a label that Julian Satran Expires August 2002 24 11iSCSI.book Page 25 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 identifies it as an initiator port name/identifier and (b) the ISID portion of the session identifier. - SCSI Port: This is the SAM2 term for an entity in a SCSI Device that provides the SCSI functionality to interface with a service delivery subsystem or transport. For iSCSI, the definition of the SCSI Initia- tor Port and the SCSI Target Port are different. - SCSI Port Name: A name made up as UTF-8 characters and is basically the iSCSI Name + 'i' or 't' + ISID or Portal Group Tag. - SCSI Target Port: This maps to an iSCSI Target Portal Group. - SCSI Target Port Name and SCSI Target Port Identifier: These are both defined to be the iSCSI Target Name together with (a) a label that identifies it as a target port name/identifier and (b) the portal group tag. - TSID (Target Session ID): The TSID is the target assigned tag for a session with a specific named initiator that and ISID. The target is generating it during session establishment and its internal format and content are not defined by this protocol except for the value 0 that is reserved and used by the initiator to indicate a new session. It is given to the target, during additional connection establishment for the same session. Julian Satran Expires August 2002 25 11iSCSI.book Page 26 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 2. Overview 2.1 SCSI Concepts The SCSI Architecture Model-2 [SAM2] describes, in detail, the archi- tecture of the SCSI family of I/O protocols. This section provides a brief background of the SCSI architecture and is intended to familiar- ize readers with its terminology. At the highest level, SCSI is a family of interfaces for requesting services from I/O devices, including hard drives, tape drives, CD and DVD drives, printers, and scanners. In SCSI terminology, an individ- ual I/O device is called a "logical unit" (LU). SCSI is a client-server architecture. Clients of a SCSI interface are called "initiators". Initiators issue SCSI "commands" to request ser- vice from a logical unit. The "device server" on the logical unit accepts SCSI commands and processes them. A "SCSI transport" maps the client-server SCSI protocol to a specific interconnect. Initiators are one endpoint of a SCSI transport. The "target" is the other endpoint. A target can contain multiple Logical Units (LUs). Each Logical Unit has an address within a target called a Logical Unit Number (LUN). A SCSI task is a SCSI command or possibly a linked set of SCSI com- mands. Some LUs support multiple pending (queued) tasks, but the queue of tasks is managed by the target. The target uses an initiator pro- vided "task tag" to distinguish between tasks. Only one command in a task can be outstanding at any given time. Each SCSI command results in an optional data phase and a required response phase. In the data phase, information can travel from the initiator to target (e.g., WRITE), target to initiator (e.g., READ), or in both directions. In the response phase, the target returns the final status of the operation, including any errors. A response termi- nates a SCSI command. Command Descriptor Blocks (CDB) are the data structures used to con- tain the command parameters that an initiator hands to a target. The CDB content and structure is defined by [SAM] and device-type specific SCSI standards. Julian Satran Expires August 2002 26 11iSCSI.book Page 27 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 2.2 iSCSI Concepts and Functional Overview The iSCSI protocol is a mapping of the SCSI remote procedure invoca- tion model (see [SAM]) over the TCP protocol. SCSI commands are car- ried by iSCSI requests and SCSI responses and status are carried by iSCSI responses. iSCSI also uses the request response mechanism for iSCSI protocol mechanisms. For the remainder of this document, the terms "initiator" and "target" refer to "iSCSI initiator node" and "iSCSI target node", respectively (see Section 2.4.1 iSCSI Architecture Model) unless otherwise quali- fied. In keeping with similar protocols, the initiator and target divide their communications into messages. This document uses the term "iSCSI protocol data unit" (iSCSI PDU) for these messages. For performance reasons, iSCSI allows a "phase-collapse". A command and its associated data may be shipped together from initiator to tar- get, and data and responses may be shipped together from targets. The iSCSI transfer direction is defined with regard to the initiator. Outbound or outgoing transfers are transfers from initiator to tar- get, while inbound or incoming transfers are from target to initiator. An iSCSI task is an iSCSI request for which a response is expected. In this document "iSCSI request", "iSCSI command", request, or (unqualified) command have the same meaning. Also, unless otherwise specified, status, response, or numbered response have the same mean- ing. 2.2.1 Layers and Sessions The following conceptual layering model is used to specify initiator and target actions and how they relate to transmitted and received Protocol Data Units: -The SCSI layer builds/receives SCSI CDBs (Command Descriptor Blocks) and relays/receives them with the remaining command execute parameters (cf. SAM2) to/from ->. Julian Satran Expires August 2002 27 11iSCSI.book Page 28 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -The iSCSI layer that builds/receives iSCSI PDUs and relays/ receives them to/from one or more TCP connections that form an initiator-target "session". Communication between the initiator and target occurs over one or more TCP connections. The TCP connections carry control messages, SCSI commands, parameters, and data within iSCSI Protocol Data Units (iSCSI PDUs). The group of TCP connections that link an initiator with a target, form a session (loosely equivalent to a SCSI I-T nexus - see Section 2.4.2 SCSI Architecture Model). A session is defined by a ses- sion ID that is composed of an initiator part and a target part. TCP connections can be added and removed from a session. Connections within a session are identified by a connection ID (CID). Across all connections within a session, an initiator sees one "target image". All target identifying elements, such as LUN, are the same. In addition, a target sees one "initiator image" across all connections within a session. Initiator that identifying elements, such as the Initiator Task Tag, can be used to identify Tag are global across the same entity session regardless of the connection on which they are sent or received. iSCSI targets and initiators MUST support at least one TCP connection and MAY support several connections in a session. For error recovery purposes, targets and initiators that support a single active connec- tion in a session may have to support two connections during recovery. 2.2.2 Ordering and iSCSI Numbering iSCSI uses Command and Status numbering schemes and a Data sequencing scheme. Command numbering is session-wide and is used for ordered command delivery over multiple connections. It can also be used as a mechanism for command flow control over a session. Status numbering is per connection and is used to enable missing sta- tus detection and recovery in the presence of transient or permanent communication errors. Data sequencing is per command or part of a command (R2T triggered sequence) and is used to detect missing data and/or R2T PDUs due to header digest errors. Julian Satran Expires August 2002 28 11iSCSI.book Page 29 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Typically, fields in the iSCSI PDUs communicate the Sequence Numbers between the initiator and target. During periods when traffic on a connection is unidirectional, iSCSI NOPOut/In PDUs may be utilized to synchronize the command and status ordering counters of the target and initiator. 2.2.2.1 Command Numbering and Acknowledging iSCSI supports ordered command delivery within a session. All com- mands (initiator-to-target PDUs) are numbered. Many SCSI activities are related to a task (SAM2). The task is identi- fied by the Initiator Task Tag for the life of the task. Commands in transit from the initiator to the target are numbered by iSCSI; the number is carried by the iSCSI PDU as CmdSN (Command- Sequence-Number). The numbering is session-wide. Outgoing iSCSI request PDUs carry this number. The iSCSI initiator allocates CmdSNs with a 32-bit unsigned counter (modulo 2**32). Comparisons and arith- metic on CmdSN SHOULD use Serial Number Arithmetic as defined in [RFC1982] where SERIAL_BITS = 32. Commands meant for immediate delivery are marked with an immediate delivery flag; they also carry CmdSN. CmdSN does not advance for com- mands marked for immediate delivery. Command numbering starts with the first login request on the first connection of a session (the leading login on the leading connection) and command numbers are incremented by 1 for every non-immediate com- mand issued afterwards. If immediate delivery is used with task management commands, these commands may reach the target task management before the tasks on which they are supposed to act. However, their CmdSN is a marker of their position in the stream of commands. The task management command MUST carry the CmdSN that is given to the next non-immediate command. The initiator and target must ensure that the task management commands act as specified by SAM2. For example, both commands and responses appear as if delivered in order. Beyond the scope of this document is the means by which one may request immediate delivery for a command or by which iSCSI decides by itself to mark a PDU for immediate delivery. Julian Satran Expires August 2002 29 11iSCSI.book Page 30 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The number of commands used for immediate delivery is not limited and their delivery to execution is not acknowledged through the numbering scheme. Immediate commands can be rejected by the iSCSI target due to a lack of resources. An iSCSI target MUST be able to handle at least one immediate task management command and one immediate non-task-man- agement iSCSI request per connection at any time. With the exception of the commands marked for immediate delivery, the iSCSI target layer MUST deliver the commands for execution in the order specified by CmdSN. Commands marked for immediate delivery may be handed over by the iSCSI target layer for execution as soon as detected. iSCSI may avoid delivering some commands for execution if required by a prior SCSI or iSCSI action (e.g., clear task set Task Management request received before all the commands on which it was supposed to act). Delivery for execution means delivery to the SCSI execution engine or an iSCSI-SCSI protocol specific execution engine (e.g., for text requests). On any given connection, the iSCSI initiator MUST send the commands in increasing order of CmdSN, except for commands that are retransmitted due to digest error recovery and connection recovery. The initiator and target are assumed to have the following three reg- isters that are unique session wide and that define the numbering mechanism: - CmdSN - the current command Sequence Number, advanced by 1 on each command shipped except for commands marked for immediate delivery. CmdsN always contains the number to be assigned next. - ExpCmdSN - the next expected command by the target. The tar- get acknowledges all commands up to, but not including, this number. The initiator has to mark the acknowledged commands as such as soon as a PDU with the corresponding ExpCmdSN is received. The target iSCSI layer sets the ExpCmdSN to the largest non-immediate CmdSN that it can deliver for execution plus 1 (no holes in the CmdSN sequence). - MaxCmdSN - the maximum number to be shipped. The queuing capacity of the receiving iSCSI layer is MaxCmdSN - ExpCmdSN + 1. ExpCmdSN and MaxCmdSN are derived from target-to-initiator PDU fields. Comparisons and arithmetic on ExpCmdSN and MaxCmdSN SHOULD Julian Satran Expires August 2002 30 11iSCSI.book Page 31 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 MUST use Serial Number Arithmetic as defined in [RFC1982] where SERIAL_BITS = 32. The target MUST NOT transmit a MaxCmdSN that is less than the last ExpCmdSN. For non-immediate commands, the CmdSN field can take any value from ExpCmdSN to MaxCmdSN. The target MUST silently ignore any non-immediate command outside of this range or non-immediate dupli- cates within the range. MaxCmdSN and ExpCmdSN fields are processed by the initiator as fol- lows: -If the PDU MaxCmdSN is less than the PDU ExpCmdSN-1 (in Serial Arithmetic Sense), they are both ignored. -If the PDU MaxCmdSN is less than the local MaxCmdSN (in Serial Arithmetic Sense), it is ignored; otherwise, it updates the local MaxCmdSN. -If the PDU ExpCmdSN is less than the local ExpCmdSN (in Serial Arithmetic Sense), it is ignored; otherwise, it updates the local ExpCmdSN. This sequence is required since updates may arrive out of order being that they travel on different TCP connections. The target MUST NOT transmit a MaxCmdSN that is less than the last ExpCmdSN. For non-immediate commands, the CmdSN field can take any value from ExpCmdSN to MaxCmdSN. The target MUST silently ignore any non-immediate command outside of this range or non-immediate dupli- cates within the range. iSCSI initiators and targets MUST support the command numbering scheme. A numbered iSCSI request will not change its allocated CmdSN, regard- less of the number of times and circumstances in which it is reissue- dreissued (see Section 6.1.1 Usage of Retry). At the target, it is assumed that CmdSN is relevant only while the command has not created any state related to its execution (execution state); afterwards, CmdSN becomes irrelevant. Testing for the execution state (repre- sented by identifying the Initiator Task Tag) is assumed to precede any other action at the target, and is followed by ordering and deliv- ery if no execution state is found or delivery if an execution state is found. Julian Satran Expires August 2002 31 11iSCSI.book Page 32 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 When the current value of the CmdSN register is Q, an initiator MUST not advance CmdSN past R + 2**31 - 1 after reissuing a command with CmdSN R on a connection while this connection is operational, unless a new non-immediate command with CmdSN equal or greater than Q was issued on the given connection and its reception acknowledged by the target (see Section 9.3 Command Retry and Cleaning Old Command Instan- cesSection 8.3 Command Retry and Cleaning Old Command Instances). The non-immediate command MUST be sent in order after the retried command. A target MUST NOT issue a command response or DATA-In PDU with status before acknowledging the command. However, the acknowledgement can be included in the response or Data-in PDU itself. 2.2.2.2 Response/Status Numbering and Acknowledging Responses in transit from the target to the initiator are numbered. The StatSN (Status Sequence Number) is used for this purpose. StatSN is a counter maintained per connection. ExpStatSN is used by the ini- tiator to acknowledge status. The status sequence number space is 32bit integers and the arithmetic operations are the regular mod(2**32) arithmetic. Status numbering starts with the Login response to the first Login request of the connection. The Login response includes an initial value for status numbering (any initial value is valid). To enable command recovery, the target MAY maintain enough state information to enable data and status recovery after a connection failure. A target can discard all the state information maintained for recovery after the status delivery is acknowledged through ExpStatSN. A large absolute difference between StatSN and ExpStatSN may indicate a failed connection. Initiators undertake recovery actions if the difference is greater than an implementation defined constant that SHOULD NOT exceed 2**31-1. Initiators and Targets MUST support the response-numbering scheme. 2.2.2.3 Data Sequencing Data and R2T PDUs, transferred as part of some command execution, MUST be sequenced. The DataSN field is used for data sequencing. For input (read) data PDUs, DataSN starts with 0 for the first data PDU of an input command and advances by 1 for each subsequent data PDU. For out- put data PDUs, DataSN starts with 0 for the first data PDU of a Julian Satran Expires August 2002 32 11iSCSI.book Page 33 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 sequence (the initial unsolicited sequence or any data PDU sequence issued to satisfy an R2T) and advances by 1 for each subsequent data PDU. R2Ts are also sequenced per command. For example, the first R2T has an R2TSN of 0 and advances by 1 for each subsequent R2T. For bidi- rectional commands, the target uses the DataSN/R2TSN to sequence Data-In and R2T PDUs in one continuous sequence (undifferentiated). Unlike command and status, data PDUs and R2Ts are not acknowledged by a field in regular outgoing PDUs. Data-In PDUs can be acknowledged on demand by a special form of the SNACK PDU. Data and R2T PDUs are implicitly acknowledged by status. The DataSN/R2TSN field enables the initiator to detect missing data or R2T PDUs. For any given write command, a target must have issued less than 2**32 R2Ts. Any input or output data sequence MUST contain less than 2**32 numbered PDUs. 2.2.3 iSCSI Login The purpose of the iSCSI login is to enable a TCP connection for iSCSI use, authenticate the parties, negotiate the session's parameters and mark the connection as belonging to an iSCSI session. A session is used to identify all the connections with a given initi- ator that belong to the same I_T nexus to a target. (See Section 2.4.2 SCSI Architecture Model for more details on how a session relates to an I_T nexus). The targets listen on a well-known TCP port or other TCP port for incoming connections. The initiator begins the login process by con- necting to one of these TCP ports. As part of the login process, the initiator and target MAY wish to authenticate each other and set a security association protocol for the session. This can occur in many different ways and is subject to negotiation. In order to protect the TCP connection, an IPsec security association MAY be established before the Login request. Using IPsec security for iSCSI is specified in Chapter 8Chapter 7 and in [SEC-IPS]. The iSCSI Login Phase is carried through Login requests and responses. Once suitable authentication has occurred and operational parameters Julian Satran Expires August 2002 33 11iSCSI.book Page 34 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 have been set, the initiator may start to send SCSI commands. How the target chooses to authorize an initiator is beyond the scope of this document. A more detailed description of the Login Phase can be found in Chapter 4. The login PDU includes a session ID that is composed of an initiator part ISID and a target part TSID. For a new session, the TSID is null. As part of the response, the target generates a TSID. During session establishment, the target identifies the SCSI initia- tor port (the "I" in the "I_T nexus") through the value pair (Initia- torName, ISID) (InitiatorName is described later in this part). Any persistent state (e.g., persistent reservations) on the target that is associated with a SCSI initiator port is identified based on this value pair. Any state associated with the SCSI target port (the "T" in the "I_T nexus") is identified externally by the TargetName and portal group tag (see Section 2.4.1 iSCSI Architecture Model) and internally in an implementation dependent way. As ISID is used to identify a per- sistent state, it is subject to reuse restrictions (see Section 2.4.3 Consequences of the Model). Before the Full Feature Phase is established, only Login Request and Login Response PDUs are allowed. Any other PDU, when received at ini- tiator or target, is a protocol error and MUST result in the connec- tion being terminated. 2.2.4 Text Mode Negotiation During login, and thereafter, some session or connection parameters are negotiated through an exchange of textual information. The initiator starts the negotiation through a Text/Login request and indicates when it is ready for completion (by setting to 1 and keeping to 1 the F bit in a Text Request or the T bit in the Login Request). The general format of text negotiation is: Originator-> = Responder-> =|NotUnderstood|Irrelevant The originator can either be the initiator or the target and the responder can either be the target or initiator, respectively. Target Julian Satran Expires August 2002 34 11iSCSI.book Page 35 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 requests are not limited to respond to key=value pairs as offered by the initiator. The target may offer key=value pairs of its own. All negotiations are stateless (i.e., the result MUST be based only on newly exchanged values). Not offering a key for negotiation is not equivalent to offering the current (or default) value. The value can be a number, a single literal constant a Boolean value (yes or no), or a list of comma separated, literal constant values. In literal list negotiation, the originator sends a list of options (literal constants which may include "None") for each key in its order of preference. The responding party answers with the first value that it supports and is allowed to use for the specific originator selected from the orig- inator list. The constant "none" MUST always be used to indicate a missing func- tion. However, none is a valid selection only if it is explicitly offered. If a responder does not support or is not allowed to use all of the offered options with a specific originator, it may use the constant "Reject". For numerical and single literal negotiations, the responding party MUST respond with the required key. The value it selects, based on the selection rule specific to the key, becomes the negotiation result. The selection of a value not admissible under the selection rules is considered a protocol error and is handled accordingly. For Boolean negotiations (keys taking the values yes or no), the responding party MUST respond with the required key and the result of the negotiation when the received value does not determine that result by itself. The last value transmitted becomes the negotiation result. The rules for selecting the value with which to respond are expressed as Boolean functions of the value received and the value that the responding party would select in the absence of knowledge of the received value. Specifically, the two cases in which responses are OPTIONAL are: Julian Satran Expires August 2002 35 11iSCSI.book Page 36 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - The Boolean function is "AND" and the value "no" is received. The outcome of the negotiation is "no". - The Boolean function is "OR" and the value "yes" is received. The outcome of the negotiation is "yes". Responses are REQUIRED in all other cases, and the value chosen and sent by the responder becomes the outcome of the negotiation. If a specific key is not relevant for the current negotiation, the responder may answer with the constant "Irrelevant" for all types of negotiation. Any other key not understood by the responder may be ignored by the responder without affecting the basic function. However, the Text Response for a key not understood MUST be key=NotUnderstood. The value "?" with any key has the meaning of enquiry and should be answered with the current value or "NotUnderstood". The value "?" MUST be used ONLY in Full Feature Phase. Whenever the responder has 2 two values for a key - one for the offering-to-responding-party direction and a second one for the responding-to-offering-party direction it will answer with the two values separated by a comma starting with the requesting-to-offering-party direction. The constants "None", "Reject", "Irrelevant", and "NotUnderstood" are reserved and must only be used as described here. Some basic key=value pairs are described in Chapter 12. All keys in Chapter 12, except for the X- extension format, MUST be supported by iSCSI initiators and targets. Manufacturers may introduce new keys by prefixing them with X- fol- lowed by their (reversed) domain name. For example the company owning the domain acme.com can issue: X-com.acme.bar.foo.do_something=3 2.2.5 iSCSI Full Feature Phase Once the initiator is authorized to do so, the iSCSI session is in the iSCSI Full Feature Phase. A session is in Full Feature Phase after successfully finishing the login phase on the first (leading) connec- tion of a session. A connection is in Full Feature Phase if the ses- Julian Satran Expires August 2002 36 11iSCSI.book Page 37 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 sion is in Full Feature Phase and the connection login has completed successfully. An iSCSI connection is not in Full Feature Phase a) when it does not have an established transport connection, or b) when it has a valid transport connection, but a successful login was not per- formed or the connection is currently logged out. In a normal Full Feature Phase, the initiator may send SCSI commands and data to the various LUs on the target by wrapping them in iSCSI PDUs that go over the established iSCSI session. For an iSCSI request issued over a TCP connection, the corresponding response and/or requested PDU(s) MUST be sent over the same connection by default. We call this "connection allegiance". If the original con- nection fails before the command is completed, the connection alle- giance of the command may be explicitly reassigned to a different transport connection as described in detail in Section 6.1 Retry and Reassign in Recovery. For SCSI commands that require data and/or a parameter transfer, the (optional) data and the status for a command MUST be sent over the same TCP connection to which the SCSI command is currently allegiant, illustrating the above rule. Thus, if an initiator issues a READ command, the target MUST send the requested data, if any, followed by the status to the initiator over the same TCP connection that was used to deliver the SCSI command. If an initiator issues a WRITE command, the initiator MUST send the data, if any, for that command. The target MUST return Ready To Transfer (R2T), if any, and the status over the same TCP connection that was used to deliver the SCSI command. Retransmission requests (SNACK PDUs) and the data and status that they generate MUST also use the same connection. However, consecutive commands that are part of a SCSI linked command- chain task MAY use different connections. Connection allegiance is strictly per-command and not per-task. During the iSCSI Full Feature Phase, the initiator and target MAY interleave unrelated SCSI com- mands, their SCSI Data, and responses over the session. Outgoing SCSI data (initiator to target user data or command parame- ters) is sent as either solicited data or unsolicited data. Solicited data is sent in response to R2T PDUs. Unsolicited data can be sent as part of an iSCSI command PDU ("immediate data") or in separate iSCSI data PDUs. An initiator may send unsolicited data as immediate up to Julian Satran Expires August 2002 37 11iSCSI.book Page 38 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the negotiated maximum PDU size or in a separate PDU sequence (up to the mode page limitFirstBurstSize). All subsequent data MUST be solicited. The maximum size of an individual data PDU or the immedi- ate-part of the first unsolicited burst MAY be negotiated at login. Targets operate in either solicited (R2T) data mode or unsolicited (non R2T) data mode. In unsolicited mode, an initial R2T that allows a transfer up to the FirstBurstSize is implied. A target MAY separately enable immediate data without enabling the more general (separate data PDUs) form of unsolicited data. An initiator SHOULD honor an R2T data request for a valid outstanding command (i.e., carrying a valid Initiator Task Tag) provided the com- mand is supposed to deliver outgoing data and the R2T specifies data within the command bounds. It is considered an error for an initiator to send unsolicited data PDUs to a target that operates in R2T mode (only solicited data is allowed). It is also an error for an initiator to send more data, whether immediate or as separate PDUs, than the SCSI iSCSI limit for first burst. At login, an initiator MAY request to send data blocks and a first burst of any size; in this case, the target MUST indicate the size of the first burst and of the immediate and data blocks that it is ready to accept. A target SHOULD NOT silently discard data and request retransmission through R2T. Initiators SHOULD NOT keep track of the data transferred to or from the target (scoreboarding); targets perform residual count calculation. Incoming data for initiators is always implicitly solic- ited. SCSI data packets are matched to their corresponding SCSI com- mands by using Tags specified in the protocol. Initiator tags for pending commands are unique initiator-wide for a session. Target tags are not strictly specified by the protocol. It is assumed that these tags are used by the target to tag (alone or in combination with the LUN) the solicited data. Target tags are gener- ated by the target and "echoed" by the initiator. The above mechanisms are designed to accomplish efficient data delivery and a large degree of control over the data flow. iSCSI initiators and targets MUST also enforce some ordering rules. Unsolicited data MUST be sent on every connection in the same order in Julian Satran Expires August 2002 38 11iSCSI.book Page 39 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 which commands were sent. A target that receives data out of order MAY terminate the session. 2.2.6 iSCSI Connection Termination An iSCSI connection may be terminated by use of a transport connection shutdown, or a transport reset. Transport reset is assumed to be an exceptional event. Graceful TCP connection shutdowns are done by sending TCP FINs. A graceful transport connection shutdown SHOULD be initiated by either party only when the connection is not in iSCSI full-feature phase. A target MAY terminate a full-feature phase connection on internal exception events, but it SHOULD announce the fact through an Asynchro- nous Message PDU. Connection termination with outstanding commands may require recovery actions. If a connection is terminated while in full-feature phase, connection cleanup (section 5) is required as a prelude to recovery. By doing connection cleanup before starting recovery, the initiator and target can avoid receiving stale PDUs after recovery. In this case, the ini- tiator sends a Logout request on one of the operational connections of a session that indicates which iSCSI connection should be logged out. 2.2.7 Naming and Addressing All iSCSI initiators and targets are named. Each target or initiator is known by an iSCSI Name. The iSCSI Name is independent of the loca- tion of the initiator and target; two formats are provided that allow the use of existing naming authorities to generate names. One of these formats allows the use of a registered domain name as a naming authority; it is important not to confuse this with an address. The iSCSI Name is a UTF-8 text string and is defined in [NDT]. iSCSI Names are used to provide: - An initiator identifier for configurations that provide multi- ple initiators behind a single IP address. - A target identifier for configurations that present multiple targets behind a single IP address and port. - A method to recognize multiple paths to the same device on different IP addresses and ports. - An identifier for source and destination targets for use in third party commands. Julian Satran Expires August 2002 39 11iSCSI.book Page 40 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - An identifier for initiators and targets to enable them to recognize each other regardless of IP address and port mapping on intermediary firewalls. The initiator MUST present both its iSCSI Initiator Name and the iSCSI Target Name to which it wishes to connect in the first login request of a new session. The only exception is if a discovery session (see Section 2.3 iSCSI Session Types) is to be established; the iSCSI Ini- tiator Name is still required, but the iSCSI Target Name may be ignored. The key "SessionType=Discovery" is sent by the initiator at login to indicate a discovery session. The default name "iSCSI" is reserved and is not used as an individual initiator or target name. iSCSI Names do not require special handling within the iSCSI layer; they are opaque and case-sensitive for purposes of comparison. Examples of iSCSI Names: iqn.1998-03.com.disk-vendor.diskarrays.sn.45678 iqn.2000-01.com.gateways.yourtargets.24 iqn.1987-06.com.os-vendor.plan9.cdrom.12345 iqn.2001-03.com.service-provider.users.customer235.host90 eui.02004567A425678D iSCSI nodes also have addresses. An iSCSI address specifies a single path to an iSCSI node and has the following format: [:] Where is one of: - IPv4 address, in dotted decimal notation. Assumed if the name contains exactly four numbers, separated by dots (.), where each number is in the range 0..255. - IPv6 address, in colon-separated hexadecimal notation, as specified in [RFC2373] and enclosed in "[" and "]" characters, as specified in [RFC2732]. - Fully Qualified Domain Name (host name). Assumed if the is neither an IPv4 nor an IPv6 address. For iSCSI targets, the in the address is optional; if speci- fied, it is the TCP port on which the target is listening for connec- Julian Satran Expires August 2002 40 11iSCSI.book Page 41 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 tions. If the is not specified, the default port 3260, assigned by IANA, will be assumed. For iSCSI initiators, the is omitted. Examples of addresses: 10.40.1.2 [FEDC:BA98:7654:3210:FEDC:BA98:7654:3210] [1080:0:0:0:8:800:200C:417A] [3ffe:2a00:100:7031::1] [1080::8:800:200C:417A] [::192.9.5.5] mydisks.example.com To assist in providing a more human-readable user interface for devices that contain iSCSI targets and initiators, a target or initi- ator may also provide an alias. This alias is a simple UTF-8 string, is not globally unique, and is never interpreted or used to identify an initiator or device within the iSCSI protocol. Its use is described in [NDT]. Third party commands require that protocol-specific addresses be com- municated within SCSI CDBs. The iSCSI protocol-specific address con- sists of an iSCSI name, or an iSCSI name + TCP address. An initiator may discover the iSCSI Target Names to which it has access, along with their addresses, using the SendTargets text request, or by other techniques discussed in [NDT]. 2.2.8 Persistent State iSCSI does not require any persistent state maintenance across ses- sions. However in some cases, SCSI requires persistent identification of the SCSI initiator port name (for iSCSI, the InitiatorName plus the ISID portion of the session identifier). (See Section 2.4.2 SCSI Architecture Model and Section 2.4.3 Consequences of the Model.) iSCSI sessions do not persist through power cycles and boot opera- tions. All iSCSI session and connection parameters are re-initialized on session and connection creation. Commands persist beyond connection termination if the session per- sists and command recovery within the session is supported. However, Julian Satran Expires August 2002 41 11iSCSI.book Page 42 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 when a connection is dropped, command execution, as perceived by iSCSI (i.e., involving iSCSI protocol exchanges for the affected task), is suspended until a new allegiance is established by the 'task reassign' task management function. (See Section 10.5 Task Management Function RequestSection 9.5 Task Management Function Request.) 2.2.9 Message Synchronization and Steering 2.2.9.1 Rationale iSCSI presents a mapping of the SCSI protocol onto TCP. This encapsu- lation is accomplished by sending iSCSI PDUs of varying lengths. Unfortunately, TCP does not have a built-in mechanism for signaling message boundaries at the TCP layer. iSCSI overcomes this obstacle by placing the message length in the iSCSI message header. This serves to delineate the end of the current message as well as the beginning of the next message. In situations where IP packets are delivered in order from the net- work, iSCSI message framing is not an issue and messages are processed one after the other. In the presence of IP packet reordering, (i.e., frames being dropped) legacy TCP implementations store the "out of order" TCP segments in temporary buffers until the missing TCP seg- ments arrive, upon which the data must be copied to the application buffers. In iSCSI, it is desirable to steer the SCSI data within these out of order TCP segments into the pre-allocated SCSI buffers rather than store them in temporary buffers. This decreases the need for ded- icated reassembly buffers as well as the latency and bandwidth related to extra copies. Relying solely on the "message length" information from the iSCSI mes- sage header may make it impossible to find iSCSI message boundaries in subsequent TCP segments due to the loss of a TCP segment that contains the iSCSI message length. The missing TCP segment(s) must be received before any of the following segments can be steered to the correct SCSI buffers (due to the inability to determine the iSCSI message boundaries). Since these segments cannot be steered to the correct location, they must be saved in temporary buffers that must then be copied to the SCSI buffers. Different schemes can be used to recover synchronization. One of these schemes is detailed in Appendix A. - Sync and Steering with Fixed Interval Markers -Appendix A. - Sync and Steering with Fixed Interval Markers -. To make these schemes work, iSCSI implementations have to Julian Satran Expires August 2002 42 11iSCSI.book Page 43 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 make sure that the appropriate protocol layers are provided with enough information to implement a synchronization and/or data steer- ing mechanism. 2.2.9.2 Synchronization (sync) and Steering Functional Model We assume that iSCSI is implemented according to the following layer- ing scheme: +------------------------+ | SCSI | +------------------------+ | iSCSI | +------------------------+ | Sync and Steering | | +-------------------+ | | | TCP | | | +-------------------+ | +------------------------+ | Lower Functional Layers| | (LFL) | +------------------------+ | IP | +------------------------+ | Link | +------------------------+ In this model, LFL can be IPsec (a mechanism changing the IP stream and invisible to TCP). We assume that Sync and Steering operates just underneath iSCSI. An implementation may choose to place Sync and Steering somewhere else in the stack if it can translate the informa- tion kept by iSCSI in terms valid for the chosen layer. According to our layering model, iSCSI considers the information it delivers to the Sync and Steering layer (headers and payloads) as a contiguous stream of bytes mapped to the positive integers from 0 to infinity. In practice, though, iSCSI is not expected to handle infi- nitely long streams; stream addressing will wrap around at 2**32-1. This model assumes that the iSCSI layer will deliver complete PDUs to underlying layers in single (atomic) operations. The underlying layer does not need to examine the stream content to discover the PDU bound- Julian Satran Expires August 2002 43 11iSCSI.book Page 44 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 aries. If a specific implementation performs PDU delivery to the Sync and Steering layer through multiple operations, it MUST bracket an operation set used to deliver a single PDU in a manner that the Sync and Steering Layer can understand. The Sync and Steering Layer (which is OPTIONAL) MUST retain the PDU end address within the stream for every delivered iSCSI PDU. To enable the Sync and Steering operation to perform Steering, addi- tional information, including identifying tags and buffer offsets, MUST also be retained for every sent PDU. The Sync and Steering Layer is required to add enough information to every sent data item (IP packet, TCP packet or some other superstructure) to enable the receiver to steer it to a memory location independent of any other piece. If the transmission stream is built dynamically, this information is used to insert Sync and Steering information in the transmission stream (at first transmission or at re-transmission) either through a globally accessible table or a call-back mechanism. If the transmis- sion stream is built statically, the Sync and Steering information is inserted in the transmission stream when data are first presented to sync and steering. The retained information can be released whenever the transmitted data is acknowledged by the receiver. (in the case of dynamically built streams, by deletion from the global table or by an additional callback). On the outgoing path, the Sync and Steering layer MUST map the outgo- ing stream addresses from iSCSI stream addresses to TCP stream sequence numbers. On the incoming path, the Sync and Steering layer extracts the Sync and Steering information from the TCP stream. It then helps steer (place) the data stream to its final location and/or recover iSCSI PDU boundaries when some TCP packets are lost or received out of order. The data stream seen by the receiving iSCSI layer is identical to the data stream that left the sending iSCSI layer. The Sync and Steering information is kept until the PDUs to which it refers are completely processed by the iSCSI layer. On the incoming path, the Sync and Steering layer does not change the way TCP notifies iSCSI about in-order data arrival. All data place- Julian Satran Expires August 2002 44 11iSCSI.book Page 45 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 ments, in-order or out-of-order, performed by the Sync and Steering layer are hidden from iSCSI while conventional, in order, data arrival notifications generated by TCP are passed through to iSCSI 2.2.9.3 Sync and Steering and Other Encapsulation Layers We recognize that in many environments the following is a more appro- priate layering model: +----------------------------------+ | SCSI | +----------------------------------+ | iSCSI | +----------------------------------+ | Upper Functional Layers (UFL) | +----------------------------------+ | Sync and Steering | | +-----------------------------+ | | | TCP | | | +-----------------------------+ | +----------------------------------+ | Lower Functional Layers (LFL) | +----------------------------------+ | IP | +----------------------------------+ | Link | +----------------------------------+ In this model, UFL can be TLS (see[RFC2246]) or some other transport conversion mechanism (a mechanism that changes the TCP stream, but that is transparent to iSCSI). To be effective and act on reception of TCP packets out of order, Sync and Steering has to be underneath UFL, and Sync and Steering data must be left out of any UFL transformation (encryption, compression, pad- ding etc.). However, Sync and Steering MUST take into account the additional data inserted in the stream by UFL. Sync and Steering MAY also restrict the type of transformations UFL may perform on the stream. This makes implementation of Sync and Steering in the presence of oth- erwise opaque UFLs less attractive. Julian Satran Expires August 2002 45 11iSCSI.book Page 46 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 2.2.9.4 Sync/Steering and iSCSI PDU Size When a large iSCSI message is sent, the TCP segment(s) that contain the iSCSI header may be lost. The remaining TCP segment(s) up to the next iSCSI message must be buffered (in temporary buffers) since the iSCSI header that indicates to which SCSI buffers the data is to be steered was lost. To minimize the amount of buffering, it is recom- mended that the iSCSI PDU size be restricted to a small value (perhaps a few TCP segments in length). During login, each end of the iSCSI session specifies the maximum iSCSI PDU size it will accept. 2.3 iSCSI Session Types iSCSI defines two types of sessions: a) Normal operational session - an unrestricted session. b) Discovery-session - a session opened only for target discovery; the target MAY accept only text requests with the SendTargets key and a logout request with reason "close the session". The session type is defined during login with key=value parameter in the login command. 2.4 SCSI to iSCSI Concepts Mapping Model The following diagram shows an example of how multiple iSCSI Nodes (targets in this case) can coexist within the same Network Entity and can share Network Portals (IP addresses and TCP ports). Other more complex configurations are also possible. See Section 2.4.1 iSCSI Architecture Model for detailed descriptions of the components of these diagrams. Julian Satran Expires August 2002 46 11iSCSI.book Page 47 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +-----------------------------------+ | Network Entity (iSCSI Client) | | | | +-------------+ | | | iSCSI Node | | | | (Initiator) | | | +-------------+ | | | | | | +--------------+ +--------------+ | | |Network Portal| |Network Portal| | | | 10.1.30.4 | | 10.1.40.6 | | +-+--------------+-+--------------+-+ | | | IP Networks | | | +-+--------------+-+--------------+-+ | |Network Portal| |Network Portal| | | | 10.1.30.21 | | 10.1.40.3 | | | | TCP Port 4 | | TCP Port 4 | | | +--------------+ +--------------+ | | | | | | ----------------- | | | | | | +-------------+ +--------------+ | | | iSCSI Node | | iSCSI Node | | | | (Target) | | (Target) | | | +-------------+ +--------------+ | | | | Network Entity (iSCSI Server) | +-----------------------------------+ 2.4.1 iSCSI Architecture Model This section describes the part of the iSCSI architecture model that has the most bearing on the relationship between iSCSI and the SCSI Architecture Model. a) Network Entity - represents a device or gateway that is acces- sible from the IP network. A Network Entity must have one or more Network Portals (see item d), each of which can be used by some iSCSI Nodes (see item (b)) contained in that Network Entity to gain access to the IP network. Julian Satran Expires August 2002 47 11iSCSI.book Page 48 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 b) iSCSI Node - represents a single iSCSI initiator or iSCSI tar- get. There are one or more iSCSI Nodes within a Network Entity. The iSCSI Node is accessible via one or more Network Portals (see item d). An iSCSI Node is identified by its iSCSI Name (see Section 2.2.6 Naming and Addressing and Chapter 12Chapter 11). The separa- tion of the iSCSI Name from the addresses used by and for the iSCSI node allows multiple iSCSI nodes to use the same addresses, and the same iSCSI node to use multiple addresses. c) An alias string could also be associated with an iSCSI Node. The alias allows an organization to associate a user friendly string with the iSCSI Name. However, the alias string is not a sub- stitute for the iSCSI Name. d) Network Portal - a component of a Network Entity that has a TCP/IP network address and that may be used by an iSCSI Node within that Network Entity for the connection(s) within one of its iSCSI sessions. In an initiator, it is identified by its IP address. In a target, it is identified by its IP address and its listening TCP port. e) Portal Groups - iSCSI supports multiple connections within the same session; some implementations will have the ability to com- bine connections in a session across multiple Network Portals. A Portal Group defines a set of Network Portals within an iSCSI Node that collectively supports the capability of coordinating a ses- sion with connections that span these portals. Not all Network Por- tals within a Portal Group need to participate in every session connected through that Portal Group. One or more Portal Groups may provide access to an iSCSI Node. Each Network Portal, as utilized by a given iSCSI Node, belongs to exactly one portal group within that node. Portal Groups are identified within an iSCSI Node by a portal group tag, a simple integer value between 1 and 65535 (see Section 12.3 SendTargetsSection 11.3 SendTargets). All Network Portals with the same portal group tag in the context of a given iSCSI Node are in the same Portal Group. Both iSCSI Initiators and iSCSI Targets have portal groups, though only the iSCSI Target Portal Groups are used directly in the iSCSI protocol (e.g., in SendTargets). See Section Section 9.1.1 Conser- vative Reuse of ISIDsSection 8.1.1 Conservative Reuse of ISIDs for references to the Initiator Portal Groups. Julian Satran Expires August 2002 48 11iSCSI.book Page 49 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 f) Portals within a Portal Group are expected to have similar hardware characteristics, as SCSI port specific mode pages may affect all portals within a portal group. (See Section 2.4.3.2 SCSI Mode Pages). The following diagram shows an example of one such configuration on a target and how a session that shares Network Portals within a Portal Group may be established. ----------------------------IP Network--------------------- | | | | +----|---------------|-----+ +----|---------+ |+ | | +---------+ +---------+ | | +---------+ | | | | | Network | | Network | | | | Network | | | | | | Portal | | Portal | | | | Portal | | | | | +--|------+ +---------+ | | +---------+ | | | | | | | | | | | | | | Portal | | | | Portal | | | | | Group 1 | | | | Group 2 | | | +--------------------------+ +--------------+ |+ | | | | | | +--------|---------------|------------+ +--------|-------------- -------+ |+ | | | | | | +----------------------------+ +-----------------------------+ | | | iSCSI Session (Target side)| | iSCSI Session (Target side) | | | | | | | | | | (iSCSI Name + TSID=2TSID = 56) | | (iSCSI Name + TSID=1TSID = 48) | | | +----------------------------+ +-----------------------------+ | | | | iSCSI Target Node | | (within Network Entity, not shown) | +-------------------------------------------------------------------+ 2.4.2 SCSI Architecture Model This section describes the relationship between the SCSI Architecture Model [SAM2] and constructs of the SCSI device, SCSI port and I_T nexus, and the iSCSI constructs, described above. Julian Satran Expires August 2002 49 11iSCSI.book Page 50 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 This relationship implies implementation requirements in order to conform to the SAM2 model and other SCSI operational functions. These requirements are detailed in Section 2.4.3 Consequences of the Model. a) SCSI Device - the SAM2 term for an entity that contains other SCSI entities. For example, a SCSI Initiator Device contains one or more SCSI Initiator Ports and zero or more application clients. A SCSI Target Device contains one or more SCSI Target Ports and one or more logical units. For iSCSI, the SCSI Device is the component within an iSCSI Node that provides the SCSI functionality. As such, there can be one SCSI Device, at most, within a given iSCSI Node. Access to the SCSI Device can only be achieved in an iSCSI normal operational session (see Section 2.3 iSCSI Session Types). The SCSI Device Name is defined to be the iSCSI Name of the node and its use is manda- tory in the iSCSI protocol. b) SCSI Port - the SAM2 term for an entity in a SCSI Device that provides the SCSI functionality to interface with a service delivery subsystem or transport. For iSCSI, the definition of SCSI Initiator Port and SCSI Target Port are different. SCSI Initiator Port: This maps to the endpoint of an iSCSI nor- mal operational session (see Section 2.3 iSCSI Session Types). An iSCSI normal operational session is negotiated through the login process between an iSCSI initiator node and an iSCSI target node. At successful completion of this process, a SCSI Initiator Port is created within the SCSI Initiator Device. The SCSI Initiator Port Name and SCSI Initiator Port Identi- fier are both defined to be the iSCSI Initiator Name together with (a) a label that identifies it as an initiator port name/ identifier and (b) the ISID portion of the session identifier. SCSI Target Port: This maps to an iSCSI target Portal Group. The SCSI Target Port Name and the SCSI Target Port Identifier are both defined to be the iSCSI Target Name together with (a) a label that identifies it as a target port name/identifier and (b) the portal group tag. The SCSI Port Name is mandatory in iSCSI. When used in SCSI parameter data, the SCSI port name should be formatted as: - The iSCSI Name in UTF-8 format, followed by - a null terminator (1byte), followed by - the ASCII character 'i' (for SCSI Initiator Port) or the ASCII character 't' (for SCSI Target Port), followed by - a null terminator (1byte), followed by - zero to 3 null pad bytes so that the complete format is a multiple of four bytes long, followed by Julian Satran Expires August 2002 50 11iSCSI.book Page 51 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - the 6byte value of the ISID (for SCSI initiator port) or the 2byte value of the portal group tag (for SCSI target port) in network byte order (BigEndian). SCSI port names have a maximum length of 264 bytes for initi- ator ports, 260 bytes for target ports, and must be a multiple of four bytes long. The ASCII character 'i' or 't' is the label that identifies this port as either a SCSI Initiator Port or a SCSI Target Port. This ASCII character also provides the interpretation and size of the remaining six bytes (initi- ator) or two bytes (target). c) I_T nexus - a relationship between a SCSI Initiator Port and a SCSI Target Port, according to [SAM2]. For iSCSI, this rela- tionship is a session, defined as a relationship between an iSCSI Initiator's end of the session (SCSI Initiator Port) and the iSCSI Target's Portal Group. The I_T nexus can be identi- fied by the conjunction of the SCSI port names. That is, the I_T nexus identifier is the tuple (iSCSI Initiator Name + 'i' + ISID, iSCSI Target Name + 't' + Portal Group Tag). NOTE: The I_T nexus identifier is not equal to the session iden- tifier (SSID). 2.4.3 Consequences of the Model This section describes implementation and behavioral requirements that result from the mapping of SCSI constructs to the iSCSI con- structs defined above. The following are the two assumptions that are the basis of these requirements: a) Between a given iSCSI Initiator and iSCSI Target, at any given time, only one session can exist with a given session identifier (SSID). b) Between a given SCSI initiator port and SCSI target port, only one I_T nexus (session) can exist. That is, no more than one nexus relationship (parallel nexus) is allowed. These assumptions lead to the following conclusions and requirements. ISID RULE: Between a given iSCSI Initiator and iSCSI Target Portal Group (SCSI target port), there can be only one session with a given value for ISID that identifies the SCSI initiator port. See Section 10.12.6 ISIDSection 9.12.5 ISID. Julian Satran Expires August 2002 51 11iSCSI.book Page 52 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The structure of the ISID that contains a naming authority component (see Section 10.12.6 ISIDSection 9.12.5 ISID and [NDT]) provides a mechanism to facilitate compliance with the ISID rule (See also Sec- tion 9.1.1 Conservative Reuse of ISIDsSection 8.1.1 Conservative Reuse of ISIDs). The iSCSI Initiator Node is expected to manage the assignment of ISIDs prior to session initiation. The "ISID RULE" does not preclude the use of the same ISID from the same iSCSI Initiator with different Target Portal Groups on the same iSCSI target or on other iSCSI targets (see Section 9.1.1 Conservative Reuse of ISIDsSection 8.1.1 Conservative Reuse of ISIDs). Allowing this would be analogous to a single SCSI Initiator Port having relationships (nexus) with multiple SCSI target ports on the same SCSI target device or SCSI target ports on other SCSI target devices. It is also possible to have multiple sessions with different ISIDs to the same Target Portal Group. Each such ses- sion would be considered to be with a different initiator even when the sessions originate from the same initiator device. The same ISID may be used by a different iSCSI initiator because it is the iSCSI Name together with the ISID that identifies the SCSI Initiator Port. NOTE: A consequence of the ISID RULE and the specification for the I_T nexus identifier is that two nexus with the same identifier should never exist at the same time. TSID RULE: The iSCSI Target SHOULD NOT select a TSID for a given login request if the resulting SSID is already in use by an existing session between the target and the requesting iSCSI Initiator. See Section 9.1.1 Conservative Reuse of ISIDsSection 8.1.1 Conservative Reuse of ISIDs. 2.4.3.1 I_T Nexus State Certain nexus relationships contain an explicit state (e.g., initia- tor-specific mode pages or reservation state) that may need to be pre- served by the target (or more correctly stated, the device server in a logical unit) through changes or failures in the iSCSI layer (e.g., session failures). In order for that state to be restored, the iSCSI initiator should re-establish its session (re-login) to the same Tar- get Portal Group using the previous ISID. That is, it should perform session recovery as described in Chapter 6. This is because the SCSI initiator port identifier and the SCSI target port identifier (or rel- Julian Satran Expires August 2002 52 11iSCSI.book Page 53 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 ative target port) form the datum that the SCSI logical unit device server uses to identify the I_T nexus. 2.4.3.2 SCSI Mode Pages If the SCSI logical unit device server does not maintain initiator- specific mode pages, and an initiator makes changes to port-specific mode pages, the changes may affect all other initiators logged in to that iSCSI Target through the same Target Portal Group. Changes via mode pages to the behavior of a portal group via one iSCSI node should not affect the behavior of this portal group with respect to other iSCSI Target Nodes, even if the underlying implementation of a portal group serves multiple iSCSI Target Nodes in the same Network Entity. 2.5 Request/Response Summary This section lists and briefly describes all the iSCSI PDU types (request and responses). All iSCSI PDUs are built as a set of one or more header segments (basic and auxiliary) and zero or one data segments. The header group and the data segment may be followed by a CRC (digest). The basic header segment has a fixed length of 48 bytes. 2.5.1 Request/Response types carrying SCSI payload 2.5.1.1 SCSI-Command This request carries the SCSI CDB and all the other SCSI execute com- mand procedure call output parameters such as task attributes, Com- mand Reference Number, Expected Data Transfer Length for one or both transfer directions (the later for bidirectional commands), and Task Tag. The I_T_L nexus is derived by the initiator and target from the LUN field in the request and the I_T nexus implicit in the session identification. In addition, the SCSI-command PDU carries information required for the proper operation of the iSCSI protocol - the command sequence num- ber (CmdSN) and the expected status number on the connection it is issued (ExpStatSN). Julian Satran Expires August 2002 53 11iSCSI.book Page 54 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Part or all of the SCSI output (write) data associated with the SCSI command may be sent as part of the SCSI-Command PDU as a data segment. 2.5.1.2 SCSI-Response The SCSI-Response carries all the SCSI execute command procedure call input parameters and the SCSI execute command procedure call return value. It contains the residual counts from the operation if any, and an indication of whether the counts represent an overflow or an under- flow, and the SCSI status if the status is valid or a response code (a non-zero return value for the execute-command procedure call) if the status is not valid. For a valid status that indicates that the command is executed but resulted in a exception (e.g., a SCSI CHECK CONDITION), the PDU data segment contains the associated sense data. Some data segment content may also be associated (in the data seg- ment) with a non-zero response code. In addition, the SCSI-Response PDU carries information required for the proper operation of the iSCSI protocol - the number of Data-In PDU that a target has sent (to enable the initiator to check that all arrived) - ExpDataSN, the Status Sequence Number on this connection - StatSN and the next Expected Command Sequence Number at target - ExpC- mdSN, the Maximum CmdSN acceptable at target from this initiator. 2.5.1.3 Task Management Function Request The task management function request provides an initiator with a way to explicitly control the execution of one or more SCSI Tasks or iSCSI functions. The PDU carries a function identifier (which task manage- ment function to perform) and enough information to unequivocally identify the task or task-set on which to perform the action even if the task(s) to act upon has not yet arrived or has been discarded due to an error. The referenced tag identifies an individual task if the function refers to an individual task. The I_T_L nexus identifies task sets and is carried by the LUN (and implied by the session identification). Julian Satran Expires August 2002 54 11iSCSI.book Page 55 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 For task sets, the CmdSN of the task management function request helps identify the tasks upon which to act, namely all tasks associated with a LUN and having a CmdSN preceding the task management function request CmdSN. The task management function request execution is completely per- formed at the target, (i.e., any coordination between responses to the tasks affected and the task management function request response is done by the target). 2.5.1.4 Task Management Function Response The Task Management Function Response carries an indication of func- tion completion for a Task Management Function Request including how it completed (response and qualifier) and additional information for failure responses (Referenced Task Tag - if an abort task failed). After the task management response indicating task management func- tion completion, the initiator will not receive any additional responses from the affected tasks. 2.5.1.5 SCSI Data-out and SCSI Data-in The SCSI Data-out and SCS SCSI Data-in are the main vehicles by which SCSI data payload is carried between initiator and target. Data pay- load is associated with a specific SCSI command through the Initiator Task Tag. For the target, convenience, outgoing solicited data also carries a Target Transfer Tag (copied from R2T) and the LUN. Each PDU contains the payload length and the data offset relative to the buffer address contained in the SCSI exec command procedure call. In each direction, the data transfer is split into "sequences". An end-of-sequence is indicated by the F bit. An outgoing sequence is either unsolicited (only the first sequence can be unsolicited) or is a complete payload sent in response to an R2T "prompt". Input sequences are built to enable the direction switching for bidi- rectional commands. For input the target may request positive acknowledgement of input data. This is limited to sessions that support error recovery and is implemented through the A bit in the SCSI Data-in PDU header. Julian Satran Expires August 2002 55 11iSCSI.book Page 56 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Data-in and Data-out PDUs also carry the DataSN to enable the initia- tor and target to detect missing PDUs (discarded due to an error). StatSN is also carried by the Data-In PDUs. To enable a SCSI command to be executed involving a minimum number of messages, the last SCSI Data-in PDU passed for a command may also con- tain the status if the status indicated termination with no exceptions (no sense or response involved). 2.5.1.6 Ready To Transfer (R2T) R2T is the mechanism by which the SCSI target "prompts" the initiator for output data. R2T passes the offset of the requested data relative of the buffer address from the execute command procedure call and the length of the solicited data to the initiator. To help the SCSI target to associate resulting Data-out with an R2T, the R2T carries the Target Transfer Tag copied by the initiator in the solicited SCSI Data-out PDUs. There are no protocol specific require- ments with regard to the value of these tags, but it is assumed that together with the LUN, they will enable the target to associate data with an R2T. R2T also carries information required for proper operation of the iSCSI protocol, such as an R2TSN (to enable an initiator to detect a missing R2T), StatSN, ExpCmdSN and MaxCmdSN. 2.5.2 Requests/Responses carrying SCSI and iSCSI Payload 2.5.2.1 Asynchronous Message Asynchronous Messages are used to carry SCSI asynchronous events (AEN) and iSCSI asynchronous messages. When carrying an AEN, the event details are reported as sense data in the data segment. Julian Satran Expires August 2002 56 11iSCSI.book Page 57 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 2.5.3 Requests/Responses carrying iSCSI Only Payload 2.5.3.1 Text Request and Text Response Text requests and responses are designed as a parameter negotiation vehicle and as a vehicle for future extension. In the data segment key=value, Text Requests/Responses carry text information with a simple syntax. Text Request/Responses may form extended sequences using the same Initiator Task Tag. The initiator uses the F (Final) flag bit in the text request header to indicate its readiness to terminate a sequence. The target uses the F (Final) flag bit in the text response header to indicate its consent to sequence termination. Text Request/Responses also use the Target Transfer Tag to indicate continuation of an operation or a new beginning. A target that wishes to continue an operation will set the Target Transfer Tag in a Text Response to a value different from the default 0xffffffff. An initia- tor willing to continue will copy this value into the Target Transfer Tag of the next Text Request. If the initiator wants to reset the tar- get (start fresh) it will set the Target Transfer Tag to 0xffffffff. Although a complete exchange is always started by the initiator, spe- cific parameter negotiations may be initiated by the initiator or tar- get. 2.5.3.2 Login Request and Login Response Login Requests and Responses are used exclusively during the login phase of each connection to set up the session and connection parame- ters (the login phase consists of a sequence of login requests and responses carrying the same Initiator Task Tag). A connection is identified by an arbitrarily selected connection-ID (CID) that is unique within a session. Similar to the Text Requests and Responses, Login Requests/Responses carry key=value text information with a simple syntax in the data segment. The Login phase proceeds through several stages (security negotia- tion, operational parameter negotiation) that are selected with two Julian Satran Expires August 2002 57 11iSCSI.book Page 58 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 binary coded fields in the header - the "current stage" (CSG) and the "next stage" (NSG) with the appearance of the later being signaled by the "transit" flag (T). The first login phase of a session plays a special role (it is called the leading login) and some header fields are determined by the lead- ing login (e.g., the version number, the maximum number of connec- tions, the session identification etc.). The command counting initial value is also set by the leading login. Status counting for each connection is initiated by the connection login. Login Requests are always immediate. A login request may indicate an implied logout (cleanup) of the con- nection to be logged in (we call this a connection restart) through the X flag in the first login request header. 2.5.3.3 Logout Request and Response Logout Requests and Responses are used for the orderly closing of con- nections for recovery or maintenance. The logout request may be issued following a target prompt (through an asynchronous message) or at an initiators initiative. When issued on the connection to be logged out no other request may follow it. The Logout response indicates that the connection or session cleanup is completed and no other responses will arrive on the connection (if received on the logging-out connection). The Logout Response indi- cates also how long the target will keep on holding resources for recovery (e.g., command execution that continues on a new connection) in Time2Retain and how long the initiator must wait before proceeding with recovery in Time2Wait. 2.5.3.4 SNACK Request With the SNACK Request, the initiator requests retransmission of num- bered-responses or data from the target. A single SNACK request covers a contiguous set of missing items called a run of a given type of items (the type is indicate in a type field in the PDU header). The run is composed of an initial item (StatSN, DataSN, R2TSN) and the number of additional missed Status, Data, or R2T PDUs (0 means only Julian Satran Expires August 2002 58 11iSCSI.book Page 59 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the initial). For long data-in sequences, the target may request (at predefined minimum intervals) a positive acknowledgement for the data sent. A SNACK request with a type field that indicates ACK and the number of Data-In PDUs acknowledged conveys this positive acknowl- edgement. 2.5.3.5 Reject Reject enables the target to report an iSCSI error condition (proto- col, unsupported option etc.) that uses a Reason field in the PDU header and includes the complete header of the bad PDU in the Reject PDU data segment. 2.5.3.6 NOP-Out Request and NOP-In Response This request/response pair may be used by an initiator and target as a "ping" mechanism to verify that a connection/session is still active and all its components are operational. Such a ping may be triggered by the initiator or target. The triggering party indicates that it wants a reply by setting a value different from the default 0xffffffff in the corresponding Initiator/Target Transfer Tag. NOP-In/NOP-Out may also be used "unidirectional" to convey to the ini- tiator/target command, status or data counter values when there is no other "carrier" and there is a need to update the initiator/target. Julian Satran Expires August 2002 59 11iSCSI.book Page 58 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 3. SCSI Mode Parameters for iSCSI There are no iSCSI specific mode pages. Julian Satran Expires August 2002 58 11iSCSI.book Page 59 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 4. Login and Full Feature Phase Negotiation 4.1 Text Format The initiator and target send a set of key=value or key=list pairs encoded in UTF-8 Unicode. All the text keys and text values specified in this document are to be presented and interpreted in the case they appear in this document. They are case sensitive. Text keys and values MUST ONLY contain letters (a-z, A-Z), digits (0-9), space (0x20), point (.), minus (-), plus (+), commercial at (@) and underscore (_). The key and value are separated by a '=' (0x3d) delimiter. Every key=value pair (including the last or only pair) MUST be followed by one null (0x00) delimiter. A list is a set of values separated by comma (0x2c). Text values may also contain colon (:) and brackets ([ and ]). Character strings are represented as plain text. Binary items can be encoded using their decimal representation (with or without leading zeros) or hexadecimal representation (e.g., 8190 is 0x1ffe). Upper and lower case letters may be used interchangeably in hexadecimal notation (i.e., 0x1aBc, 0x1AbC, 0X1aBc, and 0x1ABC are equivalent). Binary items can also be encoded using the more compact Base64 encod- ing as specified by [RFC2045] preceded by the 0b. Key names MUST NOT exceed 63 bytes. If not otherwise specified, the maximum length of an individual value (not its encoded representation) is 255 bytes not including the delim- iter (comma or null). 4.2 Text Mode Negotiation During login, and thereafter, some session or connection parameters are negotiated through an exchange of textual information. The initiator starts the negotiation through a Text/Login request and indicates when it is ready for completion (by setting to 1 and keeping to 1 the F bit in a Text Request or the T bit in the Login Request). The general format of text negotiation is: Originator-> = Responder-> =|NotUnderstood|Irrelevant|Reject Julian Satran Expires August 2002 59 11iSCSI.book Page 60 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The originator can either be the initiator or the target and the responder can either be the target or initiator, respectively. Target requests are not limited to respond to key=value pairs as offered by the initiator. The target may offer key=value pairs of its own. All negotiations are stateless and explicit (i.e., the result MUST be based only on newly exchanged values). There is no such thing as implicit offers. If an explicit offer is not made then a reply cannot be expected. The value offered can be an integer, a range defined by lower and upper value - both integers separated by a comma, a single literal constant a Boolean value (Yes or No), or a list of comma separated, literal constant values. A selected value can be an integer, a single literal constant or a Boolean value. In literal list negotiation, the originator sends a list of options (literal constants which may include "None") for each key in its order of preference. The responding party answers with the first value that it supports and is allowed to use for the specific originator selected from the orig- inator list. The constant "None" MUST always be used to indicate a missing func- tion. However, None is a valid selection only if it is explicitly offered. If a responder does not understand any particular value in a list it MUST ignore it. If a responder does not support, does not understand or is not allowed to use all of the offered options with a specific originator, it MAY use the constant "Reject". The selection of a value not admissible under the selection rules is considered a negoti- ation failure and is handled accordingly. For numerical, numerical range and single literal negotiations, the responding party MUST respond with the required key. The value it selects, based on the selection rule specific to the key, becomes the negotiation result. For a numerical range the value selected must be an integer within the offered range or "Reject" (if the range is unac- ceptable). Julian Satran Expires August 2002 60 11iSCSI.book Page 61 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 An offer of a value not admissible MAY be answered with the constant "Reject". The selection of a value not admissible under the selection rules is considered a negotiation failure and is handled accordingly. For Boolean negotiations (keys taking the values Yes or No), the responding party MUST respond with the required key and the result of the negotiation when the received value does not determine that result by itself. The last value transmitted becomes the negotiation result. The rules for selecting the value with which to respond are expressed as Boolean functions of the value received and the value that the responding party would select in the absence of knowledge of the received value. Specifically, the two cases in which responses are OPTIONAL are: - The Boolean function is "AND" and the value "No" is received. The outcome of the negotiation is "No". - The Boolean function is "OR" and the value "Yes" is received. The outcome of the negotiation is "Yes". Responses are REQUIRED in all other cases, and the value chosen and sent by the responder becomes the outcome of the negotiation. An offer of a value not admissible MAY be answered with the constant "Reject". The selection of a value not admissible under the selection rules is considered a negotiation failure and is handled accordingly. If a specific key is not relevant for the current negotiation, the responder may answer with the constant "Irrelevant" for all types of negotiation. However the negotiation is not considered as failed if the response is Irrelevant. Any other key not understood by the responder may be ignored by the responder without affecting the basic function. However, the Text Response for a key not understood MUST be key=NotUnderstood. The constants "None", "Reject", "Irrelevant", and "NotUnderstood" are reserved and must only be used as described here. Some basic key=value pairs are described in Chapter 11. All keys in Chapter 11, except for the X- extension format, MUST be supported by iSCSI initiators and targets and MUST NOT be answered with NotUnderstood. Julian Satran Expires August 2002 61 11iSCSI.book Page 62 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Manufacturers may introduce new keys by prefixing them with X- fol- lowed by their (reversed) domain name. For example the company owning the domain acme.com can issue: X-com.acme.bar.foo.do_something=3 4.3 Login Phase The login phase establishes an iSCSI session between an initiator and a target. It sets the iSCSI protocol parameters, security parameters, and authenticates the initiator and target to each other. The login phase is implemented via login request and responses only. The whole login phase is considered as a single task and has a single Initiator Task Tag (similar to the linked SCSI commands). The default MaxRecvPDULength is used during Login. The login phase sequence of commands and responses proceeds as fol- lows: - Login initial request - Login partial response (optional) - More Login requests and responses (optional) - Login Final-Response (mandatory) The initial login request of any connection MUST include the Initia- torName key=value pair. The initial login request of the first connec- tion of a session MAY also include the SessionType key=value pair. For any connection within a session whose type is not "Discovery", the first login request MUST also include the key=value pair TargetName. The Login Final-response accepts or rejects the Login Command. The Login Phase MAY include a SecurityNegotiation stage and a LoginOp- erationalNegotiation stage and MUST include at least one of them, but the included stage MAY be empty except for the mandatory names. The login requests and responses contain a field that indicates the negotiation stage (SecurityNegotiation or LoginOperationalNegotia- tion). If both stages are used, the SecurityNegotiation MUST precede the LoginOperationalNegotiation. Julian Satran Expires August 2002 62 11iSCSI.book Page 63 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Some operational parameters can be negotiated outside login through text request/response. Security MUST be completely negotiated within the Login Phase (using underlying IPsec security is specified in Chapter 7) and in [SEC- IPS]). In some environments, a target or an initiator is not interested in authenticating its counterpart. It is possible to bypass authentica- tion through the Login request and response. The initiator and target MAY want to negotiate authentication parame- ters. Once this negotiation is completed, the channel is considered secure. Most of the negotiation keys are only allowed in a specific stage. The SecurityNegotiation keys appear in Chapter 10 and the LoginOperation- alNegotiation keys appear in Chapter 11. Only a limited set of keys (marked as Declarative in Chapter 11) may be used in any of the two stages. Neither the initiator nor the target should attempt to negotiate a parameter more than once during any login stage. Attempting to do so will result in the termination of the login and connection. Any given Login request or response belongs to a specific stage; this determines the negotiation keys allowed with the command or response. Stage transition is performed through a command exchange (request/ response) that carries the T bit and the same current stage code. Dur- ing this exchange, the next stage is selected by the target and MUST NOT exceed the value stated by the initiator. The initiator can request a transition whenever it is ready, but a target can respond with a transition only after one is offered by the initiator. In a negotiation sequence, the T bit settings in one pair of login request-responses have no bearing on the T bit settings of the next pair. An initiator that has a T bit set to 1 in one pair and is answered with a T bit setting of 0 may issue the next request with T bit set to 0. Targets MUST NOT submit parameters that require an additional initia- tor login request in a login response with the T bit set to 1. Julian Satran Expires August 2002 63 11iSCSI.book Page 64 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Stage transitions during login (including entering and exit) are pos- sible only as outlined in the following table: +-----------------------------------------------------------+ |From To -> | Security | Operational | FullFeature | | | | | | | | V | | | | +-----------------------------------------------------------+ | (start) | yes | yes | no | +-----------------------------------------------------------+ | Security | no | yes | yes | +-----------------------------------------------------------+ | Operational | no | no | yes | +-----------------------------------------------------------+ The Login Final-Response that accepts a Login Command can come only as a response to a Login command with the T bit set to 1, and both the command and response MUST have FullFeaturePhase in the NSG field. 4.3.1 Login Phase Start The login phase starts with a login request from the initiator to the target. The initial login request includes: -Protocol version supported by the initiator. -Session and connection Ids. -The negotiation stage that the initiator is ready to enter. Optionally, the login request may include: -Security parameters OR -iSCSI operational parameters AND/OR -The next negotiation stage that the initiator is ready to enter. The target can answer the login in the following ways: -Login Response with Login Reject. This is an immediate rejec- tion from the target that causes the connection to terminate and the session to terminate if this is the first (or only) connection of a new session. The T bit and the CSG and NSG fields are reserved. -Login Response with Login Accept as a final response (T bit set to 1 and the NSG in both command and response are set to Full- Julian Satran Expires August 2002 64 11iSCSI.book Page 65 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 FeaturePhase). The response includes the protocol version sup- ported by the target and the session ID, and may include iSCSI operational or security parameters (that depend on the current stage). -Login Response with Login Accept as a partial response (NSG not set to FullFeaturePhase in both request and response) that indicates the start of a negotiation sequence. The response includes the protocol version supported by the target and either security or iSCSI parameters (when no security mecha- nism is chosen) supported by the target. If the initiator decides to forego the SecurityNegotiation stage, it issues the Login with the CSG set to LoginOperationalNegotiation and the target may reply with a Login Response that indicates that it is unwilling to accept the connection without SecurityNegotiation and will terminate the connection. If the initiator is willing to negotiate security, but is unwilling to make the initial parameter offer and may accept a connection without security, it issues the Login with the T bit set to 1, the CSG set to SecurityNegotiation, and NSG set to LoginOperationalNegotiation. If the target is also ready to forego security, the Login response is empty and has T bit set to 1, the CSG set to SecurityNegotiation, and NSG set to LoginOperationalNegotiation. An initiator that can operate without security and with all the oper- ational parameters taking the default values issues the Login with the T bit set to 1, the CSG set to LoginOperationalNegotiation, and NSG set to FullFeaturePhase. If the target is also ready to forego secu- rity and can finish its LoginOperationalNegotiation, the Login response has T bit set to 1, the CSG set to LoginOperationalNegotia- tion, and NSG set to FullFeaturePhase in the next stage. 4.3.2 iSCSI Security Negotiation The security exchange sets the security mechanism and authenticates the initiator user and the target to each other. The exchange proceeds according authentication method chosen in the negotiation phase and is conducted using the login requests and responses key=value parame- ters. An initiator directed negotiation proceeds as follows: -The initiator sends a login request with an ordered list of the options it supports (authentication algorithm). The options Julian Satran Expires August 2002 65 11iSCSI.book Page 66 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 are listed in the initiator's order of preference. The initi- ator MAY also send proprietary options. -The target MUST reply with the first option in the list it sup- ports and is allowed to use for the specific initiator unless it does not support any in which case it MUST answer with "Reject" (see also Section 4.2 Text Mode Negotiation). The parameters are encoded in UTF8 as key=value. For security parameters, see Chapter 10. -The initiator must be aware of the imminent completion of the SecurityNegotiation stage and MUST set the T bit to 1 and the NSG to what it would like the next stage to be. The target will answer with a Login response with the T bit set to 1 and the NSG to what it would like the next stage to be. The next stage selected will be the one the target selected. If the next stage is FullFeaturePhase, the target MUST respond with a Login Response with the Session ID and the protocol version. If the security negotiation fails at the target, then the target MUST send the appropriate Login Response PDU. If the security negotiation fails at the initiator, the initiator SHOULD close the connection. It should be noted that the negotiation might also be directed by the target if the initiator does support security, but is not ready to direct the negotiation (offer options). 4.3.3 Operational Parameter Negotiation During the Login Phase Operational parameter negotiation during the login MAY be done: - Starting with the first Login request if the initiator does not offer any security/ integrity option. - Starting immediately after the security negotiation if the initiator and target perform such a negotiation. Operational parameter negotiation MAY involve several Login request- response exchanges started and terminated by the initiator. The ini- tiator MUST indicate its intent to terminate the negotiation by set- ting the T bit to 1; the target sets the T bit to 1 on the last response. If the target responds to a Login request with the T bit set to 1 with a Login response with the T bit set to 0, the initiator should keep sending the Login request (even empty) with the T bit set to 1, while Julian Satran Expires August 2002 66 11iSCSI.book Page 67 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 it still wants to switch stage, until it receives the Login Response with the T bit set to 1. Whenever parameter action or acceptance are dependent on other param- eters, the dependent parameters MUST be sent after the parameters on which they depend. If they are sent within the same command, a response for a parameter might imply responses for others. Some session specific parameters can be specified only during the login phase begun by a login command that contains a null TSID - the leading login phase (e.g., the maximum number of connections that can be used for this session). A session is operational once it has at least one connection in Full- FeaturePhase. New or replacement connections can be added to a session only after the session is operational. For operational parameters, see Chapter 11. 4.3.4 Connection reinstatement Connection reinstatement is the process of initiator logging in with a ISID-TSID-CID combination that is possibly active from the target‚ÇÖs perspective - thus implicitly logging out the connection state machine corresponding to the CID and reinstating a new full-feature phase iSCSI connection in its place (with the same CID). Thus, the TSID in the Login PDU MUST be non-zero and CID does not change during a connection reinstatement. The Login command performs the logout function of the old connection if an explicit logout was not performed earlier. In sessions with a single connection, this may imply the opening of a second connection with the sole purpose of cleaning up the first. Targets should support opening a second connection even when they do not support multiple connections in full feature phase. If the operational ErrorRecoveryLevel is 2, connection reinstatement enables future task reassignment. If the operational ErrorRecovery- Level is less than 2, connection reinstatement is the replacement of the old CID without enabling task reassignment. In this case, all the tasks that were active on the old CID are internally terminated. The initiator connection state MUST be CLEANUP_WAIT (section 5.1) for attempting a connection reinstatement. Julian Satran Expires August 2002 67 11iSCSI.book Page 68 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 4.3.5 Session reinstatement Session reinstatement is the process of initiator logging in with an ISID that is possibly active from the target‚ÇÖs perspective - thus implicitly logging out the session state machine corresponding to the ISID and reinstating a new iSCSI session in its place (with the same ISID). Thus, the TSID in the Login PDU MUST be zero to signal session reinstatement. All the tasks that were active on the old session are internally terminated on a session reinstatement. The initiator session state MUST be FAILED (Section 5.3 Session State Diagrams) for attempting a session reinstatement. 4.3.6 Session Continuation, closure and failure Session continuation is the process by which the state of a pre-exist- ing session is continued to be in use by either connection reinstate- ment (Section 4.3.4 Connection reinstatement), or by adding a connection with a new CID. Either of these actions associates the new transport connection with the pre-existing session state. Session closure is an event defined to be either of the following - - a successful "session close" logout - a successful "connection close" logout for the last full-fea- ture phase connection when no associated connection states are waiting for cleanup (Section 5.2 Connection Cleanup State Dia- gram for Initiators and Targets) and no associated task states are waiting for reassignment. Session failure is an event where the last full-feature phase connec- tion reaches the CLEANUP_WAIT (Section 5.2 Connection Cleanup State Diagram for Initiators and Targets) state, or completes a successful recovery logout thus causing all active tasks (that are formerly alle- giant to the connection) to start waiting for task reassignment. 4.4 Operational Parameter Negotiation Outside the Login Phase Some operational parameters MAY be negotiated outside (after) the login phase. Parameter negotiation in full feature phase is done through Text requests and responses. Operational parameter negotiation MAY involve several text request-response exchanges, which the indicator always starts and terminates and uses the same Initiator Task Tag. The initi- Julian Satran Expires August 2002 68 11iSCSI.book Page 69 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 ator MUST indicate its intent to terminate the negotiation by setting the F bit to 1; the target sets the F bit to 1 on the last response. If to a text request with the F bit set to 1 the target responds with a text response with the F bit set to 0, the initiator should keep sending the text request (even empty) with the F bit set to 1, while it still wants to finish the negotiation, until it receives the text response with the F bit set to 1. Responding to a text request with the F bit set to 1 with an empty (no key=value pairs) response with the F bit set to 0 is not an error but is discouraged. Targets MUST NOT submit parameters that require an additional initia- tor text request in a text response with the F bit set to 1. In a negotiation sequence, the F bit settings in one pair of text request-responses have no bearing on the F bit settings of the next pair. An initiator that has the F bit set to 1 in a request and being answered with an F bit setting of 0 may have the next request issued with the F bit set to 0. Whenever parameter action or acceptance is dependent on other parame- ters, the dependent parameters MUST be sent after the parameters on which they depend; if sent within the same command, a response for a parameter might imply responses for others. Whenever the target responds with the F bit set to 0, it MUST set the Target Transfer Tag to a value other than the default 0xffffffff. An initiator MAY reset an operational parameter negotiation by issu- ing a Text request with the Target Transfer Tag set to the value 0xffffffff after receiving a response with the Target Transfer Tag set to a value other than 0xffffffff. A target may reset an operational parameter negotiation by answering a Text request with a Reject. Neither the initiator nor the target should attempt to negotiate a parameter more than once during any negotiation sequence without an intervening reset. If detected by the target this MUST result in a Reject with a reason of "protocol error". The initiator MUST reset the negotiation as outlined above. Julian Satran Expires August 2002 69 11iSCSI.book Page 70 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 5. State Transitions iSCSI connections and iSCSI sessions go through several well-defined states from the time they are created to the time they are cleared. An iSCSI connection is a transport connection used for carrying out iSCSI activity. The connection state transitions are described in two separate, but dependent state diagrams for ease in understanding. The first diagram, "standard connection state diagram", describes the connection state transitions when the iSCSI connection is not waiting for or undergoing a cleanup by way of an explicit or implicit Logout. The second diagram, "connection cleanup state diagram", describes the connection state transitions while performing the iSCSI connection cleanup. The "session state diagram" describes the state transitions an iSCSI session would go through during its lifetime, and it depends on the states of possibly multiple iSCSI connections that participate in the session. 5.1 Standard Connection State Diagrams 5.1.1 Standard Connection State Diagram for an Initiator Symbolic names for States: S1: FREE S2: XPT_WAIT S4: IN_LOGIN S5: LOGGED_IN (full-feature phase) S6: IN_LOGOUT S7: LOGOUT_REQUESTED S8: CLEANUP_WAIT The state diagram is as follows: Julian Satran Expires August 2002 70 11iSCSI.book Page 71 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -------<-------------+ +--------->/ S1 \<----+ | T13| +->\ /<-+ \ | | / ---+--- \ \ | | / | T2 \ | | | T8 | |T1 | | | | | | / |T7 | | | | / | | | | | / | | | | V / / | | | ------- / / | | | / S2 \ / | | | \ / / | | | ---+--- / | | | |T4 / | | | V / | T18 | | ------- / | | | / S4 \ | | | \ / | | | ---+--- | T15 | | |T5 +--------+---------+ | | | /T16+-----+------+ | | | | / -+-----+--+ | | | | | / / S7 \ |T12| | | | | / +->\ /<-+ V V | | | / / -+----- ------- | | | / /T11 |T10 / S8 \ | | V / / V +----+ \ / | | ---+-+- ----+-- | ------- | | / S5 \T9 / S6 \<+ ^ | +-----\ /--->\ / T14 | | ------- --+----+------+T17 +---------------------------+ The following state transition table represents the above diagram. Each row represents the starting state for a given transition, which after taking a transition marked in a table cell would end in the state represented by the column of the cell. For example, from state S1, the connection takes the T1 transition to arrive at state S2. The fields marked "-" correspond to undefined transitions. Julian Satran Expires August 2002 71 11iSCSI.book Page 72 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +-----+---+---+---+---+----+---+ |S1 |S2 |S4 |S5 |S6 |S7 |S8 | ---+-----+---+---+---+---+----+---+ S1| - |T1 | - | - | - | - | - | ---+-----+---+---+---+---+----+---+ S2|T2 |- |T4 | - | - | - | - | ---+-----+---+---+---+---+----+---+ S4|T7 |- |- |T5 | - | - | - | ---+-----+---+---+---+---+----+---+ S5|T8 |- |- | - |T9 |T11 |T15| ---+-----+---+---+---+---+----+---+ S6|T13 |- |- | - |T14|- |T17| ---+-----+---+---+---+---+----+---+ S7|T18 |- |- | - |T10|T12 |T16| ---+-----+---+---+---+---+----+---+ S8| - |- |- | - | - | - | - | ---+-----+---+---+---+---+----+---+ 5.1.2 Standard Connection State Diagram for a Target Symbolic names for States: S1: FREE S3: XPT_UP S4: IN_LOGIN S5: LOGGED_IN (full-feature phase) S6: IN_LOGOUT S7: LOGOUT_REQUESTED S8: CLEANUP_WAIT The state diagram is as follows: Julian Satran Expires August 2002 72 11iSCSI.book Page 73 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -------<-------------+ +--------->/ S1 \<----+ | T13| +->\ /<-+ \ | | / ---+--- \ \ | | / | T6 \ | | | T8 | |T3 | | | | | | / |T7 | | | | / | | | | | / | | | | V / / | | | ------- / / | | | / S3 \ / | | | \ / / | T18 | | ---+--- / | | | |T4 / | | | V / | | | ------- / | | | / S4 \ | | | \ / | | | ---+--- T15 | | | |T5 +--------+---------+ | | | /T16+-----+------+ | | | | / -+-----+---+ | | | | | / / S7 \ |T12| | | | | / +->\ /<-+ V V | | | / / -+----- ------- | | | / /T11 |T10 / S8 \ | | V / / V \ / | | ---+-+- ------- ------- | | / S5 \T9 / S6 \ ^ | +-----\ /--->\ / | | ------- --+----+--------+T17 +---------------------------+ The following state transition table represents the above diagram, and follows the conventions described for the initiator diagram. Julian Satran Expires August 2002 73 11iSCSI.book Page 74 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +-----+---+---+---+---+----+---+ |S1 |S3 |S4 |S5 |S6 |S7 |S8 | ---+-----+---+---+---+---+----+---+ S1| - |T3 | - | - | - | - | - | ---+-----+---+---+---+---+----+---+ S3|T6 |- |T4 | - | - | - | - | ---+-----+---+---+---+---+----+---+ S4|T7 |- |- |T5 | - | - | - | ---+-----+---+---+---+---+----+---+ S5|T8 |- |- | - |T9 |T11 |T15| ---+-----+---+---+---+---+----+---+ S6|T13 |- |- | - |- |- |T17| ---+-----+---+---+---+---+----+---+ S7|T18 |- |- | - |T10|T12 |T16| ---+-----+---+---+---+---+----+---+ S8| - |- |- | - | - | - | - | ---+-----+---+---+---+---+----+---+ 5.1.3 State Descriptions for Initiators and Targets State descriptions for the standard connection state diagram are as follows: -S1: FREE -initiator: State on instantiation, or after successful con- nection closure. -target: State on instantiation, or after successful connec- tion closure. -S2: XPT_WAIT -initiator: Waiting for a response to its transport connection establishment request. -target: Illegal -S3: XPT_UP -initiator: Illegal -target: Waiting for the Login process to commence. -S4: IN_LOGIN -initiator: Waiting for the Login process to conclude, possi- bly involving several PDU exchanges. -target: Waiting for the Login process to conclude, possibly involving several PDU exchanges. -S5: LOGGED_IN -initiator: In full-feature phase, waiting for all internal, iSCSI, and transport events. Julian Satran Expires August 2002 74 11iSCSI.book Page 75 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -target: In full-feature phase, waiting for all internal, iSCSI, and transport events. -S6: IN_LOGOUT -initiator: Waiting for a Logout response. -target: Waiting for an internal event signaling completion of logout processing. -S7: LOGOUT_REQUESTED -initiator: Waiting for an internal event signaling readiness to proceed with Logout. -target: Waiting for the Logout process to start after having requested a Logout via an Async Message. -S8: CLEANUP_WAIT -initiator: Waiting for the context and/or resources to ini- tiate the cleanup processing for this CSM. -target: Waiting for the cleanup process to start for this CSM. 5.1.4 State Transition Descriptions for Initiators and Targets -T1: -initiator: Transport connect request was made (ex: TCP SYN sent). -target: Illegal -T2: -initiator: Transport connection request timed out, or a transport reset was received, or an internal event of receiv- ing a Logout response (success) on another connection for a "close the session" Logout command was received. -target:Illegal -T3: -initiator: Illegal -target: Received a valid transport connection request that establishes the transport connection. -T4: -initiator: Transport connection established, thus prompting the initiator to start the iSCSI Login. -target: Initial iSCSI Login command was received. -T5: -initiator: The final iSCSI Login response with a Status-Class of zero was received. -target: The final iSCSI Login command to conclude the Login phase was received, thus prompting the target to send the final iSCSI Login response with a Status-Class of zero. -T6: Julian Satran Expires August 2002 75 11iSCSI.book Page 76 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -initiator: Illegal -target: Timed out waiting for an iSCSI Login, or transport disconnect indication was received, or transport reset was received, or an internal event indicating a transport time- out was received. In all these cases, the connection is to be closed. -T7: -initiator: The final iSCSI Login response was received with a non-zero Status-Class, or Login timed out, or transport dis- connect indication was received, or transport reset was received, or an internal event indicating a transport time- out was received, or an internal event of receiving a Logout response (success) on another connection for a "close the session" Logout command was received. In all these cases, the transport connection is closed. -target: The final iSCSI Login command to conclude the Login phase was received, prompting the target to send the final iSCSI Login response with a non-zero Status-Class, or Login timed out, or transport disconnect indication was received, or transport reset was received, or an internal event indi- cating a transport timeout was received, or an internal event of sending a Logout response (success) on another connection for a "close the session" Logout command was received. In all these cases, the connection is to be closed. -T8: -initiator: An internal event of receiving a Logout response (success) on a another connection for a "close the session" Logout command was received, thus closing this connection requiring no further cleanup. -target: An internal event of sending a Logout response (suc- cess) on another connection for a "close the session" Logout command was received, or an internal event of a successful connection/session reinstatement is received, thus prompting the target to close this connection cleanly. -T9, T10: -initiator: An internal event that indicates the readiness to start the Logout process was received, thus prompting an iSCSI Logout to be sent by the initiator. -target: An iSCSI Logout command was received. -T11, T12: -initiator: Async PDU with AsyncEvent "Request Logout" was received. Julian Satran Expires August 2002 76 11iSCSI.book Page 77 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -target: An internal event that requires the decommissioning of the connection is received, thus causing an Async PDU with an AsyncEvent "Request Logout" to be sent. -T13: -initiator: An iSCSI Logout response (success) was received, or an internal event of receiving a Logout response (success) on another connection for a "close the session" Logout com- mand was received. -target: An internal event was received that indicates suc- cessful processing of the Logout, which prompts an iSCSI Logout response (success) to be sent, or an internal event of sending a Logout response (success) on another connection for a "close the session" Logout command was received, or an internal event of a successful connection/session reinstate- ment is received. In all these cases, the transport connec- tion is closed. -T14: -initiator: Async PDU with AsyncEvent "Request Logout" was received again. -target: Illegal -T15, T16: -initiator: One or more of the following events caused this transition: -Internal event that indicates a transport connection tim- eout was received thus prompting transport RESET or trans- port connection closure. -A transport RESET. -A transport disconnect indication. -Async PDU with AsyncEvent "Drop connection" (for this CID). -Async PDU with AsyncEvent "Drop all connections". -target: One or more of the following events caused this tran- sition: -Internal event that indicates a transport connection tim- eout was received, thus prompting transport RESET or trans- port connection closure. -An internal event of a failed connection/session rein- statement is received. -A transport RESET. -A transport disconnect indication. Julian Satran Expires August 2002 77 11iSCSI.book Page 78 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -Internal emergency cleanup event was received which prompts an Async PDU with AsyncEvent "Drop connection" (for this CID), or event "Drop all connections". -T17: -initiator: One or more of the following events caused this transition: -Logout response (failure, i.e. a non-zero status) was received, or Logout timed out. -Any of the events specified for T15 and T16. -target: One or more of the following events caused this transition: -Internal event that indicates a failure of the Logout processing was received, which prompts a Logout response (failure, i.e. a non-zero status) to be sent. -Any of the events specified for T15 and T16. -T18: -initiator: An internal event of receiving a Logout response (success) on another connection for a "close the session" Logout command was received. -target: An internal event of sending a Logout response (suc- cess) on another connection for a "close the session" Logout command was received, or an internal event of a successful connection/session reinstatement is received. In both these cases, the connection is closed. The CLEANUP_WAIT state (S8) implies that there are possible iSCSI tasks that have not reached conclusion and are still considered busy. 5.2 Connection Cleanup State Diagram for Initiators and Targets Symbolic names for states: R1: CLEANUP_WAIT (same as S8) R2: IN_CLEANUP R3: FREE (same as S1) Whenever a connection state machine (e.g., CSM-C) enters the CLEANUP_WAIT state (S8), it must go through the state transitions additionally described in the connection cleanup state diagram either a) using a separate full-feature phase connection (let‚ÇÖs call it CSM- Julian Satran Expires August 2002 78 11iSCSI.book Page 79 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 E) in the LOGGED_IN state in the same session, or b) using a new transport connection (let‚ÇÖs call it CSM-I) in the FREE state that is to be added to the same session. In the CSM-E case, an explicit logout for the CID that corresponds to CSM-C (either as a connection or ses- sion logout) needs to be performed to complete the cleanup. In the CSM-I case, an implicit logout for the CID that corresponds to CSM-C needs to be performed by way of connection reinstatement (section 4.3.4) for that CID. In either case, the protocol exchanges on CSM-E or CSM-I to determine the state transitions for CSM-C. Therefore, this cleanup state diagram is applicable only to the instance of the con- nection in cleanup (i.e., CSM-C). In the case of an implicit logout for example, CSM-C reaches FREE (R3) at the time CSM-I reaches LOGGED_IN. In the case of an explicit logout, CSM-C reaches FREE (R3) when CSM-E receives a successful logout response while continuing to be in the LOGGED_IN state. The following state diagram applies to both initiators and targets. Julian Satran Expires August 2002 79 11iSCSI.book Page 80 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 ------- / R1 \ +--\ /<-+ / ---+--- \ / | \ M3 M1 | |M2 | | | / | | / | | / | V / | ------- / | / R2 \ | \ / | ------- | | | |M4 | | | | | | | V | ------- | / R3 \ +---->\ / ------- The following state transition table represents the above diagram, and follows the same conventions as in earlier sections. +----+----+----+ |R1 |R2 |R3 | -----+----+----+----+ R1 | - |M2 |M1 | -----+----+----+----+ R2 |M3 | - |M4 | -----+----+----+----+ R3 | - | - | - | -----+----+----+----+ 5.2.1 State Descriptions for Initiators and Targets -R1: CLEANUP_WAIT (Same as S8) -initiator: Waiting for the internal event to initiate the cleanup processing for CSM-C. Julian Satran Expires August 2002 80 11iSCSI.book Page 81 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -target: Waiting for the cleanup process to start for CSM-C. -R2: IN_CLEANUP -initiator: Waiting for the connection cleanup process to con- clude for CSM-C. -target: Waiting for the connection cleanup process to con- clude for CSM-C. -R3: FREE (Same as S1) -initiator: End state for CSM-C. -target: End state for CSM-C. 5.2.2 State Transition Descriptions for Initiators and Targets -M1: One or more of the following events was received: -initiator: -An internal event that indicates connection state time- out. -An internal event of receiving a successful Logout response on a different connection for a "close the session" Logout. -target: -An internal event that indicates connection state time- out. -An internal event of sending a Logout response (success) on a different connection for a "close the session" Logout command. -M2: An implicit/explicit logout process was initiated by the initi- ator. -In CSM-I usage: -initiator: An internal event requesting the connection (or session) reinstatement was received, thus prompting a connection (or session) reinstatement Login to be sent tran- sitioning CSM-I to state IN_LOGIN. -target: A connection/session reinstatement Login was received while in state XPT_UP. -In CSM-E usage: -initiator: An internal event that indicates that an explicit logout was sent for this CID in state LOGGED_IN. -target: An explicit logout was received for this CID in state LOGGED_IN. -M3: Logout failure detected -In CSM-I usage: Julian Satran Expires August 2002 81 11iSCSI.book Page 82 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -initiator: CSM-I failed to reach LOGGED_IN and arrived into FREE instead. -target: CSM-I failed to reach LOGGED_IN and arrived into FREE instead. -In CSM-E usage: -initiator: CSM-E either moved out of LOGGED_IN, or Logout timed out and/or aborted, or Logout response (failure) was received. -target: CSM-E either moved out of LOGGED_IN, or Logout timed out and/or aborted, or an internal event that indicates a failed Logout processing was received. A Logout response (failure) was sent in the last case. -M4: Successful implicit/explicit logout was performed. - In CSM-I usage: -initiator: CSM-I reached state LOGGED_IN, or an internal event of receiving a Logout response (success) on another connection for a "close the session" Logout command was received. -target: CSM-I reached state LOGGED_IN, or an internal event of sending a Logout response (success) on a different connection for a "close the session" Logout command was received. - In CSM-E usage: -initiator: CSM-E stayed in LOGGED_IN and received a Logout response (success), or an internal event of receiving a Logout response (success) on another connection for a "close the session" Logout command was received. -target: CSM-E stayed in LOGGED_IN and an internal event indicating a successful Logout processing was received, or an internal event of sending a Logout response (success) on a different connection for a "close the session" Logout com- mand was received. 5.3 Session State Diagrams Session State Diagram for an Initiator Symbolic Names for States: Q1: FREE Q3: LOGGED_IN Q4: FAILED Julian Satran Expires August 2002 82 11iSCSI.book Page 83 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The state diagram is as follows: ------- / Q1 \ +------>\ /<-+ / ---+--- | / | |N3 N6 | |N1 | | | | | N4 | | | +--------+ | / | | | | / | | | | / | | V V / -+--+-- -----+- / Q4 \ N5 / Q3 \ \ /<---\ / ------- ------- State transition table: +----+----+----+ |Q1 |Q3 |Q4 | -----+----+----+----+ Q1 | - |N1 | - | -----+----+----+----+ Q3 |N3 | - |N5 | -----+----+----+----+ Q4 |N6 |N4 | - | -----+----+----+----+ 5.3.1 Session State Diagram for a Target Symbolic Names for States: Q1: FREE Q2: ACTIVE Q3: LOGGED_IN Q4: FAILED Q5: IN_CONTINUE The state diagram is as follows: Julian Satran Expires August 2002 83 11iSCSI.book Page 84 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 ------- +------------------>/ Q1 \ / +-------------->\ /<-+ | | ---+--- | | | ^ | |N3 N6 | |N11 N9| V N1 | | | +------ | | | / Q2 \ | | | \ / | | --+---- +--+--- | | / Q5 \ | | | \ / N10 | | | +-+---+------------+ |N2 / | ^ | | | / |N7| |N8 | | / | | | | V / -+--+-V V----+- / Q4 \ N5 / Q3 \ \ /<-------------\ / ------- ------- State transition table: +----+----+----+----+----+ |Q1 |Q2 |Q3 |Q4 |Q5 | -----+----+----+----+----+----+ Q1 | - |N1 | - | - | - | -----+----+----+----+----+----+ Q2 |N9 | - |N2 | - | - | -----+----+----+----+----+----+ Q3 |N3 | - | - |N5 | - | -----+----+----+----+----+----+ Q4 |N6 | - | - | - |N7 | -----+----+----+----+----+----+ Q5 |N11 | - |N10 |N8 | - | -----+----+----+----+----+----+ 5.3.2 State Descriptions for Initiators and Targets -Q1: FREE -initiator: State on instantiation or after cleanup. -target: State on instantiation or after cleanup. Julian Satran Expires August 2002 84 11iSCSI.book Page 85 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -Q2: ACTIVE -initiator: Illegal -target: The first iSCSI connection in the session transi- tioned to IN_LOGIN, waiting for it to complete the login pro- cess. -Q3: LOGGED_IN -initiator: Waiting for all session events. -target: Waiting for all session events. -Q4: FAILED -initiator: Waiting for session recovery or session continua- tion. -target: Waiting for session recovery or session continua- tion. -Q5: IN_CONTINUE -initiator: Illegal -target: Waiting for session continuation attempt to reach a conclusion. 5.3.3 State Transition Descriptions for Initiators and Targets -N1: -initiator: At least one transport connection reached the LOGGED_IN state. -target: The first iSCSI connection in the session had reached the IN_LOGIN state. -N2: -initiator: Illegal -target: At least one transport connection reached the LOGGED_IN state. -N3: -initiator: Graceful closing of the session via session clo- sure (Section 4.3.6 Session Continuation, closure and fail- ure). -target: Graceful closing of the session via session closure (Section 4.3.6 Session Continuation, closure and failure). Or a successful session reinstatement cleanly closed the session. -N4: -initiator: A session continuation attempt succeeded. -target: Illegal -N5: Julian Satran Expires August 2002 85 11iSCSI.book Page 86 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 -initiator: Session failure (Section 4.3.6 Session Continua- tion, closure and failure) occurred. -target: Session failure (Section 4.3.6 Session Continuation, closure and failure) occurred. -N6: -initiator: Session state timeout occurred, or a session rein- statement cleared this session instance. This results in the freeing of all associated resources and the session state is discarded. -target: Session state timeout occurred, or a session rein- statement cleared this session instance. This results in the freeing of all associated resources and the session state is discarded. -N7: -initiator: Illegal -target: A session continuation attempt is initiated. -N8: -initiator: Illegal -target: The last session continuation attempt failed. -N9: -initiator: Illegal -target: Login attempt on the leading connection failed. -N10: -initiator: Illegal -target: A session continuation attempt succeeded. -N11: -initiator: Illegal -target: A successful session reinstatement cleanly closed the session. Julian Satran Expires August 2002 86 11iSCSI.book Page 87 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 6. iSCSI Error Handling and Recovery For any outstanding SCSI command, it is assumed that iSCSI, in con- junction with SCSI at the initiator, is able to keep enough informa- tion to be able to rebuild the command PDU, and that outgoing data is available (in host memory) for retransmission while the command is outstanding. It is also assumed that at target, incoming data (read data) MAY be kept for recovery or it can be re-read from a device server. It is further assumed that a target will keep the "status & sense" for a command it has executed if it supports status retransmission. Many of the recovery details in an iSCSI implementation are a local matter, beyond the scope of protocol standardization. However, some external aspects of the processing must be standardized to ensure interoperability. This section describes a general model for recovery in support of interoperability. See Appendix E. - Algorithmic Presen- tation of Error Recovery Classes - for further detail. Compliant implementations do not have to match the implementation details of this model as presented, but the external behavior of such implementa- tions must correspond to the externally observable characteristics of the presented model. 6.1 Retry and Reassign in Recovery This section summarizes two important and somewhat related iSCSI pro- tocol features used in error recovery. 6.1.1 Usage of Retry By resending the same iSCSI command PDU ("retry") in the absence of a command acknowledgement or response, an initiator attempts to "plug" (what it thinks are) the discontinuities in CmdSN ordering on the tar- get end. Discarded command PDUs, due to digest errors, may have cre- ated these discontinuities. Retry MUST NOT be used for reasons other than plugging command sequence gaps. In particular, all PDU retransmission (for data, or status) requests for a currently allegiant command in progress must be conveyed to the target using only the SNACK mechanism already described. This, however, does not constitute a requirement on initi- ators to use SNACK. Julian Satran Expires August 2002 87 11iSCSI.book Page 88 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 If initiators, as part of plugging command sequence gaps as described above, inadvertently issue retries for allegiant commands already in progress (i.e., targets did not see the discontinuities in CmdSN ordering), targets MUST silently discard the duplicate requests if the CmdSN window had not advanced by then. Targets MUST support the retry functionality described above. When an iSCSI command is retried, the command PDU MUST carry the orig- inal Initiator Task Tag and the original operational attributes (e.g., flags, function names, LUN, CDB etc.) as well as the original CmdSN. The command being retried MUST be sent on the same connection as the original command unless the original connection was already successfully logged out. 6.1.2 Allegiance Reassignment By issuing a "task reassign" task management command (Section 9.5.1 Function), the initiator signals its intent to continue an already active command (but with no current connection allegiance) as part of connection recovery. This means that a new connection allegiance is established for the command, that associates it to the connection on which the task management command is being issued. In reassigning connection allegiance for a command, the targets SHOULD continue the command from its current state, for example taking advantage of ExpDataSN in the iSCSI command PDU for read commands (which must be set to zero if there was no data transfer) and bring it to completion by sending (or resending) the status. However, targets MAY choose to send/receive the entire data on a reassignment of con- nection allegiance, and it is not considered an error. For all types of commands, a reassignment request implies that the task is still considered in progress by the initiator and the target must conclude the task appropriately. This might possibly involve retransmission of data/R2T/status PDUs as necessary. It is optional for targets to support the allegiance reassignment. This capability is negotiated via the ErrorRecoveryLevel text key at the login time. When a target does not support allegiance reassign- ment, it MUST respond with a task management response code of "Task failover not supported". If allegiance reassignment is supported by the target, but the task is still allegiant to a different connection, Julian Satran Expires August 2002 88 11iSCSI.book Page 89 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the target MUST respond with a task management response code of "Task still allegiant". 6.2 Usage Of Reject PDU in Recovery Targets MUST NOT implicitly terminate an active task by sending a Reject PDU for any PDU exchanged during the life of the task. If the target decides to terminate the task, a Response PDU (SCSI, Text, Task etc.) must be returned by the target to conclude the task. If the task had never been active before the Reject (i.e., the Reject is on the command PDU), targets should not send any further responses since the command itself is being discarded. The above rule means that the initiators can eventually expect a response even on Rejects, if the Reject is not for the command itself. The non-command Rejects only have diagnostic value in logging the errors, and they can be used for retransmission decisions by the ini- tiators. The CmdSN of the rejected PDU (if it carried one) MUST NOT be consid- ered received by the target (i.e., a command sequence gap must be assumed for the CmdSN). This is true even when the CmdSN can be reli- ably ascertained, as in the case of a data digest error on immediate data. However, when the DataSN of a rejected data PDU can be ascer- tained, a target MUST advance ExpDataSN for the current burst if a recovery R2T is being generated. The target MAY advance its ExpDataSN if it does not attempt to recover the lost data PDU. 6.3 Connection timeout management iSCSI defines two session-global timeout values (in seconds) - Time2Wait and Time2Retain - that are applicable when an iSCSI full- feature phase connection is taken out of service either intentionally or on an exception. Time2Wait is the initial "respite time" before attempting an explicit/implicit Logout for the CID in question or task reassignment for the affected tasks (if any). Time2Retain is the max- imum time after the initial respite interval that the task and/or con- nection state(s) is/are guaranteed to be maintained on the target to cater to a possible recovery attempt. 6.3.1 Timeouts on transport exception events A transport connection shutdown or a transport reset without any preceding iSCSI protocol interactions informing of the fact causes a Julian Satran Expires August 2002 89 11iSCSI.book Page 90 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 full-feature phase iSCSI connection to be abruptly terminated. The timeout values to be used in this case are the negotiated values of DefaultTime2Wait (Appendix 11.15 - DefaultTime2Wait -) and DefaultTime2Retain (Appendix 11.16 - DefaultTime2Retain -) text keys for the session. 6.3.2 Timeouts on planned decommissioning Any planned decommissioning of a full-feature phase iSCSI connection is preceded by either a Logout Response PDU, or an Async Message PDU. The Time2Wait and Time2Retain field values (section 9.15)in a Logout Response PDU, and the Parameter2 and Parameter3 fields of an Async Message (AsyncEvent types "drop the connection" or "drop all the con- nections"; section 9.9.1) specify the timeout values to be used in each of these cases. These timeout values are applicable only for the affected connection, and the tasks active on that connection. These timeout values have no bearing on initiator timers (if any) that are already running on con- nections or tasks associated with that session. 6.4 Format Errors Explicit violations of the PDU layout rules stated in this document are format errors. Violations, when detected, usually indicate a major implementation flaw in one of the parties. When a target or an initiator receives an iSCSI PDU with a format error, it MUST immediately terminate all transport connections in the session either with a connection close or with a connection reset and escalate the format error to session recovery (see Section 6.12.4 Ses- sion Recovery). 6.5 Digest Errors The discussion of the legal choices in handling digest errors below excludes session recovery as an explicit option, but either party detecting a digest error may choose to escalate the error to session recovery. When a target receives any iSCSI PDU with a header digest error, it MUST silently discard the PDU. Julian Satran Expires August 2002 90 11iSCSI.book Page 91 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 When a target receives any iSCSI PDU with a payload digest error, it MUST answer with a Reject iSCSI PDU with a Reason-code of Data-Digest- Error and discard the PDU. - If the discarded PDU is a solicited or unsolicited iSCSI data PDU (for immediate data in a command PDU, non-data PDU rule below applies), the target MUST do one of the following: a) Request retransmission with a recovery R2T. [OR] b) Terminate the task with a response PDU with the reason "proto- col service CRC error" (Section 9.4.3 Response). If the target chooses to implement this option, it MUST wait to receive all the data (signaled by a Data PDU with the final bit set for all out- standing R2Ts) before sending the response PDU. A task management command (similar to an abort task) from the initiator during this wait may also conclude the task. - No further action is necessary for targets if the discarded PDU is a non-data PDU. When an initiator receives any iSCSI PDU with a header digest error, it MUST discard the PDU. When an initiator receives any iSCSI PDU with a payload digest error, it MUST discard the PDU. - If the discarded PDU is an iSCSI data PDU, the initiator MUST do one of the following: a) Request the desired data PDU through SNACK. In its turn, the target MUST either resend the data PDU or, reject the SNACK with a Reject PDU with a reason-code of "Data-SNACK Reject" in which case - i) if the status had not already been sent for the com- mand, the target MUST terminate the command with an iSCSI response reason(Section 9.4.3 Response) of "SNACK rejected". ii) if the status was already sent, no further action is necessary for the target. Initiator in this case MUST internally signal the completion with the "SNACK rejected" reason (Section 9.4.3 Response) disregarding any received status PDU, but must wait for the status to be received before doing so. [OR] b) Abort the task and terminate the command with an error. - If the discarded PDU is a response PDU, the initiator MUST do one of the following: Julian Satran Expires August 2002 91 11iSCSI.book Page 92 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 a) Request PDU retransmission with a status SNACK. [OR] b) Logout the connection for recovery and continue the tasks on a different connection instance as described in Section 6.1 Retry and Reassign in Recovery. [OR] c) Logout to close the connection (abort all the commands associ- ated with the connection). - No further action is necessary for initiators if the discarded PDU is an unsolicited PDU (e.g., Async, Reject). 6.6 Sequence Errors When an initiator receives an iSCSI R2T/data PDU with an out-of-order R2TSN/DataSN or a SCSI response PDU with an ExpDataSN that implies missing data PDU(s), it means that the initiator must have hit a header or payload digest error on one or more earlier R2T/data PDUs. The initiator MUST address these implied digest errors as described in Section 6.5 Digest Errors. When a target receives a data PDU with an out-of-order DataSN, it means that the target must have hit a header or payload digest error on at least one of the earlier data PDUs. Tar- get MUST address these implied digest errors as described in Section 6.5 Digest Errors. When an initiator receives an iSCSI status PDU with an out-of-order StatSN that implies missing responses, it MUST address the one or more missing status PDUs as described in Section 6.5 Digest Errors. As a side effect of receiving the missing responses, the initiator may dis- cover missing data PDUs. If the initiator wants to recover the missing data for a command, it MUST NOT acknowledge the received responses that start from the StatSN of the interested command, until it has completed receiving all the data PDUs of the command. When an initiator receives duplicate R2TSNs (due to proactive retransmission of R2Ts by the target) or duplicate DataSNs (due to proactive SNACKs by the initiator), it MUST discard the duplicates. 6.7 SCSI Timeouts An iSCSI initiator MAY attempt to plug a command sequence gap on the target end (in the absence of an acknowledgement of the command by way of ExpCmdSN) before the ULP timeout by retrying the unacknowledged command, as described in Section 6.1 Retry and Reassign in Recovery. Julian Satran Expires August 2002 92 11iSCSI.book Page 93 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 On a ULP timeout for a command (that carried a CmdSN of n), the iSCSI initiator MUST abort the command by either using the Abort Task task management function request, or a "close the connection" Logout if it intends to continue the session. In using an explicit Abort, if the ExpCmdSN is still less than (n+1), the target may see the abort request while missing the original command itself due to one of the following reasons: - The original command was dropped due to digest error. - The connection on which the original command was sent was suc- cessfully logged out (on logout, the unacknowledged commands issued on the connection being logged out are discarded). If the abort request is received and the original command is missing, targets MUST consider the original command with that RefCmdSN to be received and issue a task management response with the response code: "Task does not exist". This response concludes the task on both ends. 6.8 Negotiation Failures Text request and response sequences, when used to set/negotiate oper- ational parameters, constitute the negotiation/parameter setting. A negotiation failure is considered one or more of the following: - None of the choices or the stated value is acceptable to one negotiating side. - The text request timed out, and possibly aborted. - The text request was answered with a reject. The following two rules are to be used to address negotiation fail- ures: - During Login, any failure in negotiation MUST be considered a login process failure and the login phase must be terminated, and with it the connection. If the target detects the failure, it must terminate the login with the appropriate login response code. - A failure in negotiation, while in the full-feature phase, will terminate the entire negotiation sequence that may con- sist of a series of text requests that use the same Initiator Task Tag. The operational parameters of the session or the connection MUST continue to be the values agreed upon during an earlier successful negotiation (i.e., any partial results of this unsuccessful negotiation must be undone). Julian Satran Expires August 2002 93 11iSCSI.book Page 94 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 6.9 Protocol Errors The authors recognize that mapping framed messages over a "stream" connection, such as TCP, make the proposed mechanisms vulnerable to simple software framing errors. On the other hand, the introduction of framing mechanisms to limit the effects of these errors may be onerous on performance for simple implementations. Command Sequence Numbers and the above mechanisms for connection drop and re-establishment help handle this type of mapping errors. All violations of iSCSI PDU exchange sequences specified in this draft are also protocol errors. This category of errors can be only be addressed by fixing the implementations; iSCSI defines Reject and response codes to enable this. 6.10 Connection Failures iSCSI can keep a session in operation if it is able to keep/establish at least one TCP connection between the initiator and the target in a timely fashion. It is assumed that targets and/or initiators recog- nize a failing connection by either transport level means (TCP), a gap in the command, a response stream that is not filled for a long time, or by a failing iSCSI NOP (ping). The latter MAY be used periodically by highly reliable implementations. Initiators and targets MAY also use the keep-alive option on the TCP connection to enable early link failure detection on otherwise idle links. On connection failure, the initiator and target MUST do one of the following: - Attempt connection recovery within the session (Section 6.12.3 Connection Recovery). - Logout the connection with the reason code "closes the connec- tion" (Section 9.14.3 Reason Code), re-issue missing commands, and implicitly terminate all active commands. This option requires support for the within-connection recovery class (Section 6.12.2 Recovery Within-connection). - Perform session recovery (Section 6.12.4 Session Recovery). Either side may choose to escalate to session recovery, and the other side MUST give it precedence. On a connection failure, a target MUST terminate and/or discard all the active immediate commands regardless of which of the above options is used (i.e., immediate commands are not recoverable across connection failures). Julian Satran Expires August 2002 94 11iSCSI.book Page 95 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 6.11 Session Errors If all the connections of a session fail and cannot be re-established in a short time, or if initiators detect protocol errors repeatedly, an initiator may choose to terminate a session and establish a new session. The initiator takes the following actions: - It resets or closes all the transport connections. - It terminates all outstanding requests with an appropriate response before initiating a new session. When the session timeout (the connection state timeout for the last failed connection) happens on the target, it takes the following actions: - Resets or closes the TCP connections (closes the session). - Aborts all Tasks in the task set for the corresponding initi- ator. 6.12 Recovery Classes iSCSI enables the following classes of recovery (in the order of increasing scope of affected iSCSI tasks): - Within a command (i.e., without requiring command restart). - Within a connection (i.e., without requiring the connection to be rebuilt, but perhaps requiring command restart). - Connection recovery (i.e., perhaps requiring connections to be rebuilt and commands to be reissued). - Session recovery. The recovery scenarios detailed in the rest of this section are repre- sentative rather than exclusive. In every case, they detail the lowest class recovery that MAY be attempted. The implementer is left to decide under which circumstances to escalate to the next recovery class and/or what recovery classes to implement. Both the iSCSI tar- get and initiator MAY escalate the error handling to an error recovery class, which impacts a larger number of iSCSI tasks in any of the cases identified in the following discussion. In all classes, the implementer has the choice of deferring errors to the SCSI initiator (with an appropriate response code), in which case Julian Satran Expires August 2002 95 11iSCSI.book Page 96 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the task, if any, has to be removed from the target and all the side- effects, such as ACA, must be considered. Use of within-connection and within-command recovery classes MUST NOT be attempted before the connection is in full feature phase. 6.12.1 Recovery Within-command At the target, the following cases lend themselves to within-command recovery: - Lost data PDU - realized through one of the following: a) Data digest error - dealt with as specified in Section 6.5 Digest Errors, using the option of a recovery R2T. b) Sequence reception timeout (no data or partial-data-and-no-F- bit) - considered an implicit sequence error and dealt with as specified in Section 6.6 Sequence Errors, using the option of a recovery R2T. c) Header digest error, which manifests as a sequence reception timeout, or a sequence error - dealt with as specified in Section 6.6 Sequence Errors, using the option of a recovery R2T. At the initiator, the following cases lend themselves to within-com- mand recovery: Lost data PDU or lost R2T - realized through one of the follow- ing: a) Data digest error - dealt with as specified in Section 6.5 Digest Errors, using the option of a SNACK. b) Sequence reception timeout (no status) - dealt with as speci- fied in Section 6.6 Sequence Errors, using the option of a SNACK. c) Header digest error, which manifests as a sequence reception timeout, or a sequence error - dealt with as specified in Section 6.6 Sequence Errors, using the option of a SNACK. To avoid a race with the target, which may already have a recovery R2T or a termination response on its way, an initiator SHOULD NOT origi- nate a SNACK for an R2T based on its internal timeouts (if any). Recovery in this case is better left to the target. The timeout values used by the initiator and target are outside the scope of this document. Sequence reception timeout is generally a large enough value to allow the data sequence transfer to be complete. Julian Satran Expires August 2002 96 11iSCSI.book Page 97 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 6.12.2 Recovery Within-connection At the initiator, the following cases lend themselves to within-con- nection recovery: - Requests not acknowledged for a long time. Requests are acknowledged explicitly through ExpCmdSN or implicitly by receiving data and/or status. The initiator MAY retry non- acknowledged commands as specified in Section 6.1 Retry and Reassign in Recovery. - Lost iSCSI numbered Response. It is recognized by either iden- tifying a data digest error on a Response PDU or a Data-In PDU carrying the status, or by receiving a Response PDU with a higher StatSN than expected. In the first case, digest error handling is done as specified in Section 6.5 Digest Errors using the option of a SNACK. In the second case, sequence error handling is done as specified in Section 6.6 Sequence Errors, using the option of a SNACK. At the target, the following cases lend themselves to within-connec- tion recovery: - Status/Response not acknowledged for a long time. The target MAY issue a NOP-IN (with a valid Target Transfer Tag or other- wise) that carries the next status sequence number it is going to use in the StatSN field. This helps the initiator detect any missing StatSN(s) and issue a SNACK for the status. The timeout values used by the initiator and the target are outside the scope of this document. 6.12.3 Connection Recovery At an iSCSI initiator, the following cases lend themselves to connec- tion recovery: - TCP connection failure. The initiator MUST close the connec- tion. It then MUST either Logout the failed connection, or Login with an implied Logout, and reassign connection alle- giance for all commands still in progress associated with the failed connection on another connection (that MAY be a newly established connection) using the "Task reassign" task manage- ment function (see Section 9.5.1 Function). Note that for an initiator a command is in progress as long as it has not received for a response or a Data-In PDU including status. Julian Satran Expires August 2002 97 11iSCSI.book Page 98 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 - N.B. The logout function is mandatory, while a new connection establishment is mandatory only if the failed connection was the last or only connection in the session. - Receiving an Asynchronous Message that indicates one or all connections in a session has been dropped. The initiator MUST handle it as a TCP connection failure for the connection(s) referred to in the Message. At an iSCSI target, the following cases lend themselves to connection recovery: - TCP connection failure. The target MUST close the connection and if more than one connection is available, the target SHOULD send an Asynchronous Message that indicates it has dropped the connection. Then, the target will wait for the initiator to continue recovery. 6.12.4 Session Recovery Session recovery should be performed when all other recovery attempts have failed. Very simple initiators and targets MAY perform session recovery on all iSCSI errors and therefore, place the burden of recov- ery on the SCSI layer and above. Session recovery implies the closing of all TCP connections, inter- nally aborting all executing and queued tasks for the given initiator at the target, terminating all outstanding SCSI commands with an appropriate SCSI service response at the initiator, and restarting a session on a new set of connection(s) (TCP connection establishment and login on all new connections). Reserve-Release managed SCSI reservations ("Regular" reservations) that are secured during an iSCSI session persist until they are cleared using regular SCSI means. When the session object is cleared, i.e. when the session object reaches the FREE state, iSCSI layer informs SCSI layer of the fact and expects the SCSI layer to initiate clearing actions (if any) that it deems appropriate. If the iSCSI session is reconstructed (thus between the same SCSI ports with the same nexus identifier - see Section 4.3.6 Session Continuation, clo- sure and failure), any existing regular reservations may be automati- cally associated to this new session if they where not cleared by the SCSI layer. Julian Satran Expires August 2002 98 11iSCSI.book Page 99 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Persistent SCSI reservations are not affected by iSCSI session fail- ures, and only the regular SCSI means can be used to handle these res- ervations when the session is reconstructed (necessarily between the same SCSI ports and so with the same nexus identifier). 6.13 Error Recovery Hierarchy The error recovery classes and features described are organized into a hierarchy for ease in understanding and to limit the myriad of imple- mentation possibilities, with hopes that this significantly contrib- utes to highly interoperable implementations. The attributes of this hierarchy are as follows: a) Each level is a superset of the capabilities of the previous level. For example, Level 1 support implies supporting all capa- bilities of Level 0 and more. b) As a corollary, supporting a higher error recovery level means increased sophistication and possibly an increase in resource requirement. c) Supporting error recovery level "n" is advertised and negoti- ated by each iSCSI entity by exchanging the text key "ErrorRecov- eryLevel=n". The lower of the two exchanged values is the operational ErrorRecoveryLevel for the session. The following diagram represents the error recovery hierarchy. + / \ / 2 \ <-- Connection recovery +-----+ / 1 \ <-- Digest failure recovery +---------+ / 0 \ <-- Session failure recovery +-------------+ The following table lists the error recovery capabilities expected from the implementations that support each error recovery level. Julian Satran Expires August 2002 99 11iSCSI.book Page 100 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +-------------------+--------------------------------------------+ |ErrorRecoveryLevel | Associated Error recovery capabilities | +-------------------+--------------------------------------------+ | 0 | Session recovery class | | | (Section 6.12.4 Session Recovery) | +-------------------+--------------------------------------------+ | 1 | Digest failure recovery (See Note below.) | +-------------------+--------------------------------------------+ | 2 | Connection recovery class | | | (Section 6.12.3 Connection Recovery) | +-------------------+--------------------------------------------+ Note: Digest failure recovery is comprised of two recovery classes: Within-Connection recovery class (Section 6.12.2 Recovery Within-con- nection) and Within-Command recovery class (Section 6.12.1 Recovery Within-command). Supporting error recovery level "0" is mandatory, while the rest are optional to implement. In implementation terms, the above striation means that the following incremental sophistication with each level is required. +-------------------+---------------------------------------------+ |Level transition | Incremental requirement | +-------------------+---------------------------------------------+ | 0->1 | PDU retransmissions on the same connection | +-------------------+---------------------------------------------+ | 1->2 | Retransmission across connections and | | | allegiance reassignment | +-------------------+---------------------------------------------+ Julian Satran Expires August 2002 100 11iSCSI.book Page 101 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 7. Security Considerations Historically, native storage systems have not had to consider secu- rity because their environments offered minimal security risks. That is, these environments consisted of storage devices either directly attached to hosts or connected via a subnet distinctly separate from the communications network. The use of storage protocols, such as SCSI, over IP networks requires that security concerns be addressed. iSCSI implementations MUST provide means of protection against active attacks (e.g., pretending to be another identity, message insertion, deletion, modification, and replaying) and passive attacks (e.g.,eavesdropping, gaining advantage by analyzing the data sent over the line). Although technically possible, iSCSI SHOULD NOT be configured without security. iSCSI without security should be confined, in extreme cases, to closed environments without any security risk. The following section describes the security mechanisms provided by an iSCSI implementation. 7.1 iSCSI Security Mechanisms The entities involved in iSCSI security are the initiator, target, and the IP communication end points. iSCSI scenarios where multiple ini- tiators or targets share a single communication end point are expected. To accommodate such scenarios, iSCSI uses two separate security mechanisms: In-band authentication between the initiator and the target at the iSCSI connection level (carried out by exchange of iSCSI Login PDUs), and packet protection (integrity, authentication, and confidentiality) by IPsec at the IP level. The two security mech- anisms complement each other: The in-band authentication provides end-to-end trust (at login time) between the iSCSI initiator and the target, while IPsec provides a secure channel between the IP communi- cation end points. Further details on typical iSCSI scenarios and the relation between the initiators, targets, and the communication end points can be found in [SEC-IPS]. Julian Satran Expires August 2002 101 11iSCSI.book Page 102 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 7.2 In-band Initiator-Target Authentication With this mechanism, the target authenticates the initiator and the initiator optionally authenticates the target. The authentication is performed on every new iSCSI connection by an exchange of iSCSI Login PDUs using a negotiated authentication method. The authentication method cannot assume an underlying IPsec protec- tion, since IPsec is optional to use. An attacker should gain as lit- tle advantage as possible by inspecting the authentication phase PDUs. Therefore, a method using clear text (or equivalent) passwords is not acceptable; on the other hand, identity protection is not strictly required. This mechanism protects against an unauthorized login to storage resources by using a false identity (spoofing). Once the authentica- tion phase is completed, if the underlying IPsec is not used, all PDUs are sent and received in clear. This mechanism alone (without underly- ing IPsec) should only be used when there is no risk of eavesdropping, message insertion, deletion, modification, and replaying. The CHAP authentication method (see Chapter 10) is vulnerable to an off-line dictionary attack. In environments where this attack is a concern, CHAP SHOULD NOT be used without additional protection. Underlying IPsec encryption provides protection against this attack. The strength of the SRP authentication method (specified in Chapter 13) is dependent on the characteristics of the group being used (i.e., the prime modulus N and generator g). As described in [RFC2945], N is required to be a Sophie-German prime (of the form N = 2q + 1, where q is also prime) and the generator g is a primitive root of GF(n). In iSCSI authentication, the prime modulus N MUST be at least 768 bits. Upon receiving N and g from the Target, the Initiator MUST verify that they satisfy the above requirements (and otherwise, abort the connec- tion). This verification MAY start by trying to match N and g with a well-known group that satisfies the above requirements. Well-known SRP groups are provided in [SEC-IPS]. Compliant iSCSI initiators and targets MUST at least implement the SRP authentication method [RFC2945] (see Chapter 10). Julian Satran Expires August 2002 102 11iSCSI.book Page 103 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 7.3 IPsec The IPsec mechanism is used by iSCSI for packet protection (crypto- graphic integrity, authentication, and confidentiality) at the IP level between the iSCSI communicating end points. The following sec- tions describe the IPsec protocols that must be implemented for data integrity and authentication, confidentiality, and key management. Detailed considerations and recommendations for using IPsec for iSCSI are provided in [SEC-IPS]. 7.3.1 Data Integrity and Authentication Data authentication and integrity is provided by a keyed Message Authentication Code in every sent packet. This code protects against message insertion, deletion, and modification. Protection against message replay is realized by using a sequence counter. An iSCSI compliant initiator or target MUST provide data integrity and authentication by implementing IPsec [RFC2401] with ESP in tunnel mode [RFC2406] with the following iSCSI specific requirements: - HMAC-SHA1 MUST be implemented [RFC2404]. - AES CBC MAC with XCBC extensions SHOULD be implemented [AESCBC]. If the IPsec implementation of an iSCSI initiator or target conforms to the [RFC2401] definition of a host, then to comply with section 4.1 of [RFC2401] it MUST also implement ESP in transport mode (with the same requirements above). The ESP anti-replay service MUST also be implemented. At the high speeds iSCSI is expected to operate, a single IPsec SA could rapidly cycle through the 32-bit IPsec sequence number space. In view of this, in the future it may be desirable for an iSCSI imple- mentation that operates at speeds of 1 Gbps or faster to implement the IPsec sequence number extension [SEQ-EXT]. 7.3.2 Confidentiality Confidentiality is provided by encrypting the data in every packet. Confidentiality SHOULD always be used together with data integrity Julian Satran Expires August 2002 103 11iSCSI.book Page 104 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 and authentication to provide comprehensive protection against eaves- dropping, message insertion, deletion, modification, and replaying. An iSCSI compliant initiator or target MUST provide confidentiality by implementing IPsec [RFC2401] with ESP in tunnel mode [RFC2406] with the following iSCSI specific requirements: - 3DES in CBC mode MUST be implemented [RFC2451]. - AES in Counter mode SHOULD be implemented [AESCTR] (NOTE: This is still subject to the IPsec WG's standardization plans). If the IPsec implementation of an iSCSI initiator or target conforms to the [RFC2401] definition of a host, then to comply with section 4.1 of [RFC2401] it MUST also implement ESP in transport mode (with the same requirements above). DES in CBC mode SHOULD NOT be used due to its inherent weakness. The NULL encryption algorithm MUST also be implemented. 7.3.3 Policy, Security Associations and Key Management A compliant iSCSI implementation MUST meet the key management requirements of the IPsec protocol suite. Authentication, security association negotiation, and key management MUST be provided by implementing IKE [RFC2409] using the IPsec DOI [RFC2407] with the fol- lowing iSCSI specific requirements: - Peer authentication using a pre-shared key MUST be supported. Certificate-based peer authentication using digital signa- tures MAY be supported. Peer authentication using the public key encryption methods outlined in IKE sections 5.2 and 5.3[7] SHOULD NOT be used. - When digital signatures are used to achieve authentication, an IKE negotiator SHOULD use IKE Certificate Request Payload(s) to specify the certificate authority. IKE negotiators SHOULD check the pertinent Certificate Revocation List (CRL) before accepting a PKI certificate for use in IKE authentication pro- cedures. - Both IKE Main Mode and Aggressive Mode MUST be supported. IKE main mode with pre-shared key authentication method SHOULD NOT be used when either the initiator or the target uses dynami- cally assigned IP addresses. While pre-shared keys in many cases offer good security, situations where dynamically assigned addresses are used force the use of a group pre- Julian Satran Expires August 2002 104 11iSCSI.book Page 105 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 shared key, which creates vulnerability to a man-in-the-middle attack. - In the IKE Phase 2 Quick Mode exchanges for creating the Phase 2 SA, the Identity Payload fields MUST be present. ID_IPV4_ADDR, ID_IPV6_ADDR (if the protocol stack supports IPv6) and ID_FQDN Identity payloads MUST be supported; ID_USER_FQDN MAY be supported. The IP Subnet, IP Address Range, ID_DER_ASN1_DN, ID_DER_ASN1_GN formats SHOULD NOT be used. The ID_KEY_ID Identity Payload MUST NOT be used. Manual keying MUST NOT be used since it does not provide the necessary re-keying support. When IPsec is used the receipt of an IKE Phase 2 delete message SHOULD NOT be interpreted as a reason for tearing down the iSCSI TCP connec- tion. If additional traffic is sent on it, a new IKE Phase 2 SA will be created to protect it. The method used by the initiator to determine whether the target should be connected using IPsec is regarded as an issue of IPsec pol- icy administration, and thus not defined in the iSCSI standard. How- ever, as iSCSI has an is an in-band discovery mechanism (discovery session and SendTargets), the use or non-use of IPsec in any opera- tional session is assumed to be identical to that of the discovery session. If an iSCSI target is discovered via a SendTargets request in a dis- covery session not using IPsec, the initiator should assume that it does not need IPsec to establish a session to that target. If an iSCSI target is discovered using a discovery session that does use IPsec, the initiator should use IPsec when establishing a session to that target. Julian Satran Expires August 2002 105 11iSCSI.book Page 106 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 8. Notes to Implementers This section notes some of the performance and reliability consider- ations of the iSCSI protocol. This protocol was designed to allow efficient silicon and software implementations. The iSCSI tag mecha- nism was designed to enable RDMA at the iSCSI level or lower. The guiding assumption made throughout the design of this protocol is that targets are resource constrained relative to initiators. Implementers are also advised to consider the implementation conse- quences of the iSCSI to SCSI mapping model as outlined in Section 2.4.3 Consequences of the Model. 8.1 Multiple Network Adapters The iSCSI protocol allows multiple connections, not all of which need to go over the same network adapter. If multiple network connections are to be utilized with hardware support, the iSCSI protocol command- data-status allegiance to one TCP connection ensures that there is no need to replicate information across network adapters or otherwise require them to cooperate. However, some task management commands may require some loose form of cooperation or replication at least on the target. 8.1.1 Conservative Reuse of ISIDs Historically, the SCSI model (and implementations and applications based on that model) has assumed that SCSI ports are static, physical entities. Recent extensions to the SCSI model have taken advantage of persistent worldwide unique names for these ports. In iSCSI however, the SCSI initiator ports are the endpoints of dynamically created ses- sions, so the presumption of "static and physical" does not apply. In any case, the model clauses (particularly, Section 2.4.2 SCSI Archi- tecture Model) provide for persistent, reusable names for the iSCSI- type SCSI initiator ports even though there does not need to be any physical entity bound to these names. To both minimize the disruption of legacy applications and to better facilitate the SCSI features that rely on persistent names for SCSI ports, iSCSI implementations should attempt to provide a stable pre- sentation of SCSI Initiator Ports (both to the upper OS-layers and to Julian Satran Expires August 2002 106 11iSCSI.book Page 107 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the targets to which they connect). This can be achieved in an initi- ator implementation by conservatively reusing ISIDs. In other words, the same ISID should be used in the Login process to multiple target portal groups (of the same iSCSI Target or different iSCSI Targets). The ISID RULE (Section 2.4.3 Consequences of the Model) only prohibits reuse to the same target portal group. It does not "preclude" reuse to other target portal groups. The principle of conservative reuse "encourages" reuse to other tar- get portal groups. When a SCSI target device sees the same (Initia- torName, ISID) pair in different sessions to different target portal groups, it can identify the underlying SCSI Initiator Port on each session as the same SCSI port. In effect, it can recognize multiple paths from the same source. 8.1.2 iSCSI Name and ISID/TSID Use The designers of the iSCSI protocol envisioned there being one iSCSI Initiator Node Name per operating system image on a machine. This enables SAN resource configuration and authentication schemes based on a system's identity. It supports the notion that it should be possible to assign access to storage resources based on "initiator device" identity. When there are multiple hardware or software components coordinated as a single iSCSI Node, there must be some (logical) entity that rep- resents the iSCSI Node that makes the iSCSI Node Name available to all components involved in session creation and login. Similarly, this entity that represents the iSCSI Node must be able to coordinate ses- sion identifier resources (ISID for initiators and TSID for targets) to enforce both the ISID and TSID RULES (see Section Section 2.4.3 Consequences of the Model). For targets, because of the closed environment, implementation of this entity should be straightforward. However, vendors of iSCSI hardware (e.g., NICs or HBAs) intended for targets, should provide mechanisms for configuration of the iSCSI Node Name and for configura- tion and/or coordination of TSIDs across the portal groups instanti- ated by multiple instances of these components within a target. One mechanism is to allow for static or dynamic partitioning of the TSID namespace among the portal groups. Such a partitioning allows each portal group to act independently of other portal groups when assign- ing TSIDs, and facilitates enforcement of the TSID RULE (Section 2.4.3 Consequences of the Model). Julian Satran Expires August 2002 107 11iSCSI.book Page 108 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 For initiators, in the long term, it is expected that operating system vendors will take on the role of this entity and provide standard APIs that can inform components of their iSCSI Node Name and can configure and/or coordinate ISID allocation, use and reuse. Recognizing that such initiator APIs are not available today, other implementations of the role of this entity are possible. For example, a human may instantiate the (common) Node name as part of the installation process of each iSCSI component involved in session creation and login. This may be done either by pointing the component to a vendor-specific location for this datum or to a system-wide loca- tion. The structure of the ISID namespace (see Section 9.12.5 ISID and [NDT]) facilitates implementation of the ISID coordination by allow- ing each component vendor to independently (of other vendor's compo- nents) coordinate allocation and use and reuse its own partition of the ISID namespace in a vendor-specific manner. Partitioning of the ISID namespace within initiator portal groups managed by that vendor allows each such initiator portal group to act independently of all other portal groups when selecting an ISID for a login; this facili- tates enforcement of the ISID RULE (see Section 2.4.3 Consequences of the Model) at the initiator. A vendor of iSCSI hardware (e.g., NICs or HBAs) intended for use in the initiators must allow, in addition to a mechanism for configuring the iSCSI Node Name, for a mechanism to configure and/or coordinate ISIDs for all sessions managed by multiple instances of that hardware within a given iSCSI Node. Such configuration might be either perma- nently pre-assigned at the factory (in a necessarily globally unique way), statically assigned (e.g., partitioned across all the NICs at initialization in a locally unique way), or dynamically assigned (e.g., on-line allocator, also in a locally unique way). In the lat- ter two cases, the configuration may be via public APIs (perhaps driven by an independent vendor's SW, such as the OS vendor) or via private APIs driven by the vendor's own SW. 8.2 Autosense and Auto Contingent Allegiance (ACA) Autosense refers to the automatic return of sense data to the initia- tor in case a command did not complete successfully. iSCSI initiators and targets MUST support autosense. Julian Satran Expires August 2002 108 11iSCSI.book Page 109 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 ACA helps preserve ordered command execution in the presence of errors. As iSCSI can have many commands in-flight between initiator and target, iSCSI initiators and targets SHOULD support ACA. 8.3 Command Retry and Cleaning Old Command Instances To avoid having old, retried command instances appear in a valid com- mand window after a command sequence number wrap around, the protocol requires (see Section 2.2.2.1 Command Numbering and Acknowledging) that on every connection on which a retry has been issued, a non-imme- diate command be issued and acknowledged within a 2**31-1 commands interval since the retry was issued. This requirement can be fulfilled by an implementation in several ways. The simplest technique to use is to send a (non-retry) non-immediate SCSI command (or a NOP if no SCSI command is available for a while) after every command retry on the connection on which the retry was attempted. As errors are deemed rare events, this technique is prob- ably the most effective, as it does not involve additional checks at the initiator when issuing commands. 8.4 Synch and Steering Layer and Performance While a synch and steering layer is optional, an initiator/target that does not have it working against a target/initiator that demands synch and steering may experience performance degradation caused by packet reordering and loss. Providing a synch and steering mechanism is rec- ommended for all high-speed implementations. 8.5 Unsolicited Data and Performance Unsolicited data on write are meant to reduce the effect of latency on throughput (no R2T is needed to start sending data). In addition, immediate data are meant to reduce the protocol overhead (both band- width and execution time). However, negotiating an amount of unsolicited data for writes and sending less than the negotiated amount when the total data amount to be sent by a command is larger than the negotiated amount may nega- tively impact performance and may not be supported by all the targets. Julian Satran Expires August 2002 109 11iSCSI.book Page 110 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 8.6 Considerations for State-dependent devices Sequential access devices operate on the principle that the position of the device is based on the last command processed. As such, command processing order and knowledge of whether or not the previous command was processed is of the utmost importance to maintain data integrity. As an example, inadvertent retries of SCSI commands when it is not known if the previous SCSI command was processed is a potential data integrity risk. For a sequential access device, consider the scenario where a SCSI SPACE command to backspace one filemark is issued and then re-issued due to no status received for the command. If the first SPACE command was actually processed, the re-issued SPACE command, if processed, will cause the position to change. Thus, a subsequent write operation will write data to the wrong position and any previous data at that position will be overwritten. For a medium changer device, consider the scenario where an EXCHANGE MEDIUM command (the SOURCE ADDRESS and DESTINATION ADDRESS are the same thus performing a swap) is issued and then re-issued due to no status received for the command. If the first EXCHANGE MEDIUM command was actually processed, the re-issued EXCHANGE MEDIUM command, if processed, will perform the swap again. The net effect is no swap was performed thus leaving a data integrity exposure. All commands that change the state of the device (as in SPACE commands for sequential access devices, and EXCHANGE MEDIUM for medium changer device), MUST be issued as non-immediate commands for deterministic and in order delivery to iSCSI targets. For many of those state changing commands the execution model also assumes that the command is executed exactly once. For those com- mands a retry at SCSI level is not feasible or very difficult and error recovery at iSCSI level is advisable. 8.6.1 Determining the proper ErrorRecoveryLevel The implementation and usage of a specific ErrorRecoveryLevel should be determined based on the deployment scenarios of a given iSCSI implementation. Generally, the following factors must be considered before deciding on the proper level of recovery: Julian Satran Expires August 2002 110 11iSCSI.book Page 111 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 a) Application resilience to I/O failures. b) Required level of availability in the face of transport connec- tion failures. c) Probability of transport layer "checksum escape" frequency. This in turn decides the iSCSI digest failure frequency, and thus the criticality of iSCSI-level error recovery. The details of estimating this probability are outside the scope of this docu- ment. A consideration of the above factors for SCSI tape devices as an exam- ple suggests that implementations SHOULD use ErrorRecoveryLevel=1 when transport connection failure is not a concern, and ErrorRecov- eryLevel=2 when the connection failure is also of high likelihood dur- ing a backup/retrieval. Julian Satran Expires August 2002 111 11iSCSI.book Page 112 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9. iSCSI PDU Formats All multi-byte integers that are specified in formats defined in this document are to be represented in network byte order (i.e., big endian). Any field that appears in this document assumes that the most significant byte is the lowest numbered byte and the most signif- icant bit (within byte or field) is the highest numbered bit unless specified otherwise. Any compliant sender MUST set all bits not defined and all reserved fields to zero unless specified otherwise. Any compliant receiver MUST ignore any bit not defined and all reserved fields unless speci- fied otherwise. Reserved fields are marked by the word "reserved", some abbreviation of "reserved" or by "." for individual bits when no other form of marking is technically feasible. 9.1 iSCSI PDU Length and Padding iSCSI PDUs are padded to the closest integer number of four byte words. The padding bytes SHOULD be 0. 9.2 PDU Template, Header, and Opcodes All iSCSI PDUs have one or more header segments and, optionally, a data segment. After the entire header segment group a header-digest may follow. The data segment MAY also be followed by a data-digest. The Basic Header Segment (BHS) is the first segment in all of the iSCSI PDUs. The BHS is a fixed-length 48-byte header segment. It may be followed by Additional Header Segments (AHS), a Header-Digest, a Data Segment, and/or a Data-Digest. The overall structure of an iSCSI PDU is as follows: Julian Satran Expires August 2002 112 11iSCSI.book Page 113 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0/ Basic Header Segment (BHS) / +/ / +---------------+---------------+---------------+---------------+ 48/ Additional Header Segment (AHS) (optional) / +/ / +---------------+---------------+---------------+---------------+ ---- +---------------+---------------+---------------+---------------+ k/ Header-Digest (optional) / +/ / +---------------+---------------+---------------+---------------+ l/ Data Segment(optional) / +/ / +---------------+---------------+---------------+---------------+ m/ Data-Digest (optional) / +/ / +---------------+---------------+---------------+---------------+ All PDU segments and digests are padded to an integer number of four byte words. The padding bytes SHOULD be sent as 0. iSCSI response PDUs do not have AH Segments. 9.2.1 Basic Header Segment (BHS) The BHS is 48 bytes long. The Opcode and DataSegmentLength fields appear in all iSCSI PDUs. In addition, when used, the Initiator Task Tag and Logical Unit Number always appear in the same location in the header. The format of the BHS is: Julian Satran Expires August 2002 113 11iSCSI.book Page 114 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|I| Opcode | Opcode-specific fields | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Opcode-specific fields | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag or Opcode-specific fields | +---------------+---------------+---------------+---------------+ 20/ Opcode-specific fields / +/ / +---------------+---------------+---------------+---------------+ 48 9.2.1.1 I For request PDUs, the I bit set to 1 is an immediate delivery marker. 9.2.1.2 Opcode The Opcode indicates the type of iSCSI PDU the header encapsulates. The Opcodes are divided into two categories: initiator opcodes and target opcodes. Initiator opcodes are in PDUs sent by the initiators (request PDUs). Target opcodes are in PDUs sent by the target (response PDUs). Initiators MUST NOT use target opcodes and targets MUST NOT use initi- ator opcodes. Initiator opcodes defined in this specification are: 0x00 NOP-Out 0x01 SCSI Command (encapsulates a SCSI Command Descriptor Block) 0x02 SCSI Task Management Function Request 0x03 Login Command 0x04 Text request 0x05 SCSI Data-out (for WRITE operations) Julian Satran Expires August 2002 114 11iSCSI.book Page 115 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 0x06 Logout Command 0x10 SNACK Request 0x1c-0x1e Vendor specific codes Target opcodes are: 0x20 NOP-In 0x21 SCSI Response -contains SCSI status and possibly sense information or other response information. 0x22 SCSI Task Management Function Response 0x23 Login Response 0x24 Text Response 0x25 SCSI Data-in -for READ operations. 0x26 Logout Response 0x31 Ready To Transfer (R2T) - sent by target when it is ready to receive data. 0x32 Asynchronous Message -sent by target to indicate certain special conditions. 0x3c-0x3e Vendor specific codes 0x3f Reject All other opcodes are reserved. 9.2.1.3 Opcode-specific Fields These fields have different meanings for different opcode types. 9.2.1.4 TotalAHSLength Total length of all AHS header segments in four byte words including padding, if any. The TotalAHSLength is used only in PDUs that have an AHS and MUST be 0 in all other PDUs. 9.2.1.5 DataSegmentLength This is the data segment payload length in bytes (excluding padding). The DataSegmentLength MUST be 0 whenever the PDU has no data segment 9.2.1.6 LUN Some opcodes operate on a specific Logical Unit. The Logical Unit Num- ber (LUN) field identifies which Logical Unit. If the opcode does not relate to a Logical Unit, this field is either ignored or may be used in an opcode specific way. The LUN field is 64-bits and should be Julian Satran Expires August 2002 115 11iSCSI.book Page 116 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 formatted in accordance with [SAM2] i.e., LUN[0] from [SAM2] is BHS byte 8 and so on up to LUN[8] from [SAM2] that is BHS byte 15.. 9.2.1.7 Initiator Task Tag The initiator assigns a Task Tag to each iSCSI task it issues. While a task exists, this tag MUST uniquely identify it session-wide. SCSI may also use the initiator task tag as part of the SCSI task identifier when the time span during which an iSCSI initiator task tag must be unique extends over the time span during which a SCSI task tag must be unique. However, the iSCSI Initiator Task Tag has to exist and be unique even for untagged SCSI commands. 9.2.2 Additional Header Segment (AHS) The general format of an AHS is: Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0| AHSLength | AHSType | AHS-Specific | +---------------+---------------+---------------+---------------+ 4/ AHS-Specific / +/ / +---------------+---------------+---------------+---------------+ x 9.2.2.1 AHSType The AHSType field is coded as follows: bit 7-6 - Reserved bit 5-0 - AHS code 0 - Reserved 1 - Extended CDB 2 - Expected Bidirectional Read Data Length 3 - 59 Reserved 60- 63 Non-iSCSI extensions Julian Satran Expires August 2002 116 11iSCSI.book Page 117 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.2.2.2 AHSLength This field contains the effective length in bytes of the AHS excluding AHSType and AHSLength (not including padding). The AHS is padded to the smallest integer number of 4 byte words (i.e., from 0 up to 3 pad- ding bytes). 9.2.2.3 Extended CDB AHS The format of the Extended CDB AHS is: Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0| AHSLength (CDBLength-15) | 0x01 | Reserved | +---------------+---------------+---------------+---------------+ 4/ ExtendedCDB...+padding / +/ / +---------------+---------------+---------------+---------------+ x 9.2.2.4 Bidirectional Expected Read-Data Length AHS The format of the Bidirectional Read Expected Data Transfer Length AHS is: Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0| AHSLength (0x0005) | 0x02 | Reserved | +---------------+---------------+---------------+---------------+ 4| Expected Read-Data Length | +---------------+---------------+---------------+---------------+ 8 9.2.3 Header Digest and Data Digest Optional header and data digests protect the integrity of the header and data, respectively. The digests, if present, are located, respec- tively, after the header and PDU-specific data and include the padding bytes. Julian Satran Expires August 2002 117 11iSCSI.book Page 118 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The digest types are negotiated during the login phase. The separation of the header and data digests is useful in iSCSI rout- ing applications, where only the header changes when a message is for- warded. In this case, only the header digest should be re-calculated. Digests are not included in data or header length fields. A zero-length Data Segment also implies a zero-length data-digest. 9.2.4 Data Segment The (optional) Data Segment contains PDU associated data. Its payload effective length is provided in the BHS field - DataSegmentLength. The Data Segment is also padded to an integer number of 4 byte words. Julian Satran Expires August 2002 118 11iSCSI.book Page 119 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.3 SCSI Command The format of the SCSI Command PDU is: Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|I| 0x01 |F|R|W|0 0|ATTR | Reserved | CRN or Rsvd | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| Logical Unit Number (LUN) | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Expected Data Transfer Length | +---------------+---------------+---------------+---------------+ 24| CmdSN | +---------------+---------------+---------------+---------------+ 28| ExpStatSN | +---------------+---------------+---------------+---------------+ 32/ SCSI Command Descriptor Block (CDB) / +/ / +---------------+---------------+---------------+---------------+ 48| AHS (if any), Header Digest (if any) | +---------------+---------------+---------------+---------------+ / (DataSegment - Command Data + Data Digest (if any))(optional) / +/ / +---------------+---------------+---------------+---------------+ 9.3.1 Flags and Task Attributes (byte 1) The flags for a SCSI Command are: bit 7 (F) set to 1 when no unsolicited SCSI Data-Out PDUs fol- low this PDU. For a write, if Expected Data Transfer Length is larger than the DataSegmentLength the target may solicit additional data through R2T. bit 6 (R) set to 1 when input data is expected. Julian Satran Expires August 2002 119 11iSCSI.book Page 120 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 bit 5 (W) set to 1 when output data is expected. bit 4-3 Reserved bit 2-0 contains Task Attributes. Task Attributes (ATTR) have one of the following integer values (see [SAM2] for details): 0 - Untagged 1 - Simple 2 - Ordered 3 - Head of Queue 4 - ACA 5-7 - Reserved Setting both the W and the F bit to 0 is an error. The R and W MAY both be 1 when the corresponding Expected Data Trans- fer Lengths are 0, but they CANNOT both be 0 when the corresponding Expected Data Transfer Lengths are not 0. 9.3.2 CRN SCSI command reference number - if present in the SCSI execute command arguments (according to [SAM2]). 9.3.3 CmdSN - Command Sequence Number Enables ordered delivery across multiple connections in a single ses- sion. 9.3.4 ExpStatSN Command responses up to ExpStatSN-1 (mod 2**32) have been received (acknowledges status) on the connection. 9.3.5 Expected Data Transfer Length For unidirectional operations, the Expected Data Transfer Length field contains the number of bytes of data involved in this SCSI oper- ation. For a unidirectional write operation (W flag set to 1 and R flag set to 0), the initiator uses this field to specify the number of bytes of data it expects to transfer for this operation. For a unidi- rectional read operation (W flag set to 0 and R flag set to 1), the initiator uses this field to specify the number of bytes of data it Julian Satran Expires August 2002 120 11iSCSI.book Page 121 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 expects the target to transfer to the initiator. It corresponds to the SAM2 byte count. For bidirectional operations (both R and W flags are set to 1), this field contains the number of data bytes involved in the write trans- fer. For bidirectional operations, an additional header segment MUST be present in the header sequence that indicates the Bidirectional Read Expected Data Transfer Length. The Expected Data Transfer Length field and the Bidirectional Read Expected Data Transfer Length field correspond to the SAM2 byte count If the Expected Data Transfer Length for a write and the length of the immediate data part that follows the command (if any) are the same, then no more data PDUs are expected to follow. In this case, the F bit MUST be set to 1. If the Expected Data Transfer Length is higher than the FirstBurstSize (the negotiated maximum amount of unsolicited data the target will accept), the initiator SHOULD send the maximum size of unsolicited data. The target MAY terminate a command in error for which the Expected Data Transfer Length is higher than the FirstBurstSize and for which the initiator sent less than the FirstBurstSize unsolicited data. Upon completion of a data transfer, the target informs the initiator (through residual counts) of how many bytes were actually processed (sent and/or received) by the target. 9.3.6 CDB - SCSI Command Descriptor Block There are 16 bytes in the CDB field to accommodate the commonly used CDBs. Whenever the CDB is larger than 16 bytes, an Extended CDB AHS MUST be used to contain the CDB spillover. 9.3.7 Data Segment - Command Data Some SCSI commands require additional parameter data to accompany the SCSI command. This data may be placed beyond the boundary of the iSCSI header in a data segment. Alternatively, user data (for example, from a WRITE operation) can be placed in the same PDU (both cases are referred to as immediate data). These data are governed by the general rules for solicited vs. unsolicited data. Julian Satran Expires August 2002 121 11iSCSI.book Page 122 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.4 SCSI Response The format of the SCSI Response PDU is: Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x21 |1 . .|o|u|O|U|.| Response | Status | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Reserved | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36| ExpDataSN or Reserved | +---------------+---------------+---------------+---------------+ 40| Bidirectional Read Residual Count | +---------------+---------------+---------------+---------------+ 44| Residual Count | +---------------+---------------+---------------+---------------+ 48| Digests if any... | +---------------+---------------+---------------+---------------+ / Data Segment (Optional) / +/ / +---------------+---------------+---------------+---------------+ 9.4.1 Flags (byte 1) bit 6-5 Reserved bit 4 - (o) set for Bidirectional Read Residual Overflow. In this case, the b Bidirectional Read Residual Count indicates Julian Satran Expires August 2002 122 11iSCSI.book Page 123 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the number of bytes that were not transferred to the initiator because the initiator's Expected Bidirectional Read Data Transfer Length was not sufficient. bit 3 - (u) set for Bidirectional Read Residual Underflow. In this case, the Bidirectional Read Residual Count indicates the number of bytes that were not transferred to the initiator out of the number of bytes expected to be transferred. bit 2 - (O) set for Residual Overflow. In this case, the Resid- ual Count indicates the number of bytes that were not trans- ferred because the initiator's Expected Data Transfer length was not sufficient. For a bidirectional operation, the Resid- ual Count contains the residual for the write operation. bit 1 - (U) set for Residual Underflow. In this case, the Resid- ual Count indicates the number of bytes that were not trans- ferred out of the number of bytes that expected to be transferred. For a bidirectional operation, the Residual Count contains the residual for the write operation. bit 0 - (0) Reserved Bits O and U and bits o and u are mutually exclusive. For a response other than "Command Completed at Target" bit 4-1 MUST be 0. 9.4.2 Status The Status field is used to report the SCSI status of the command (as specified in [SAM2]) and is valid only if the Response Code is Command Completed at target. Some of the status codes defined in [SAM2] are: 0x00 GOOD 0x02 CHECK CONDITION 0x08 BUSY 0x18 RESERVATION CONFLICT 0x28 TASK SET FULL 0x30 ACA ACTIVE 0x40 TASK ABORTED See [SAM2] for the complete list and definitions. If a SCSI device error is detected while data from the initiator is still expected (the command PDU did not contain all the data and the Julian Satran Expires August 2002 123 11iSCSI.book Page 124 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 target has not received a Data PDU with the final bit Set), the target MUST wait until it receives a Data PDU with the F bit set in the last expected sequence, before sending the Response PDU. 9.4.3 Response This field contains the iSCSI service response. iSCSI service response codes defined in this specification are: 0x00 - Command Completed at Target 0x01 - Target Failure 0x80-0xff - Vendor specific The Response is used to report a Service Response. The exact mapping of the iSCSI response codes to SAM service response symbols is outside the scope of this document. Certain iSCSI conditions result in the command being terminated at the target (response Command Completed at Target) with a SCSI Check Condi- tion Status as outlined in the next table: +--------------------------+----------+---------------------------+ | Reason |Sense | Additional Sense Code & | | |Key | Qualifier | +--------------------------+----------+---------------------------+ | Unexpected unsolicited |Aborted | ASC = 0x0c ASCQ = 0x0c | | data |Command-0B| Write Error | +--------------------------+----------+---------------------------+ | Not enough unsolicited |Aborted | ASC = 0x0c ASCQ = 0x0d | | data |Command-0B| Write Error | +--------------------------+----------+---------------------------+ | Protocol Service CRC |Aborted | ASC = 0x47 ASCQ = 0x05 | | error |Command-0B| CRC Error Detected | +--------------------------+----------+---------------------------+ | SNACK rejected |Aborted | ASC = 0x11 ASCQ = 0x13 | | |Command-0B| Read Error | +--------------------------+----------+---------------------------+ The target reports the "Not enough unsolicited data" condition only if it does not support output (write) operations in which the total data length is higher than FirstBurstSize, but the initiator sent less than FirstBurstSize amount of unsolicited data, and out-of-order R2Ts can- not be used. Julian Satran Expires August 2002 124 11iSCSI.book Page 125 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.4.4 Residual Count The Residual Count field is only valid in the case where either the U bit or the O bit is set. If neither bit is set, the Residual Count field SHOULD be zero. If the O bit is set, the Residual Count indi- cates the number of bytes that were not transferred because the initi- ator's Expected Data Transfer Length was not sufficient. If the U bit is set, the Residual Count indicates the number of bytes that were not transferred out of the number of bytes expected to be transferred. 9.4.5 Bidirectional Read Residual Count The Bidirectional Read Residual Count field is only valid in the case where either the u bit or the o bit is set. If neither bit is set, the Bidirectional Read Residual Count field SHOULD be zero. If the o bit is set, the Bidirectional Read Residual Count indicates the number of bytes that were not transferred to the initiator because the initia- tor's Expected Bidirectional Read Transfer Length was not sufficient. If the u bit is set, the Bidirectional Read Residual Count indicates the number of bytes that were not transferred to the initiator out of the number of bytes expected to be transferred. 9.4.6 Data Segment - Sense and Response Data Segment iSCSI targets MUST support and enable autosense. If Status is CHECK CONDITION (0x02), then the Data Segment contains sense data for the failed command. For some iSCSI responses, the response data segment MAY contain some response related information, (e.g., for a target failure, it may con- tain a vendor specific detailed description of the failure). If the DataSegmentLength is not 0, the format of the Data Segment is as follows: Julian Satran Expires August 2002 125 11iSCSI.book Page 126 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|SenseLength | Sense Data | +---------------+---------------+---------------+---------------+ x/ Sense Data / +---------------+---------------+---------------+---------------+ y/ Response Data / / / +---------------+---------------+---------------+---------------+ z| 9.4.6.1 SenseLength Length of Sense Data. 9.4.7 ExpDataSN The number of Data-In (read) PDUs the target has sent for the command. This field is reserved if the response code is not Command Completed at Target or the command is a write command. 9.4.8 StatSN - Status Sequence Number StatSN is a Sequence Number that the target iSCSI layer generates per connection and that in turn, enables the initiator to acknowledge sta- tus reception. StatSN is incremented by 1 for every response/status sent on a connection except for responses sent as a result of a retry or SNACK. In the case of responses sent due to a retransmission request, the StatSN MUST be the same as the first time the PDU was sent unless the connection has since been restarted. 9.4.9 ExpCmdSN - Next Expected CmdSN from this Initiator ExpCmdSN is a Sequence Number that the target iSCSI returns to the initiator to acknowledge command reception. It is used to update a local register with the same name. An ExpCmdSN equal to MaxCmdSN+1 indicates that the target cannot accept new commands. Julian Satran Expires August 2002 126 11iSCSI.book Page 127 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.4.10 MaxCmdSN - Maximum CmdSN from this Initiator MaxCmdSN is a Sequence Number that the target iSCSI returns to the initiator to indicate the maximum CmdSN the initiator can send. It is used to update a local register with the same name. If MaxCmdSN is equal to ExpCmdSN-1, this indicates to the initiator that the target cannot receive any additional commands. When MaxCmdSN changes at the target while the target has no pending PDUs to convey this information to the initiator, it MUST generate a NOP-IN to carry the new MaxCmdSN. Julian Satran Expires August 2002 127 11iSCSI.book Page 128 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.5 Task Management Function Request Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|I| x02 |1| Function | Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| Logical Unit Number (LUN) or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Referenced Task Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| CmdSN | +---------------+---------------+---------------+---------------+ 28| ExpStatSN | +---------------+---------------+---------------+---------------+ 32| RefCmdSN or ExpDataSN | +---------------+---------------+---------------+---------------+ 36/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48 9.5.1 Function The Task Management functions provide an initiator with a way to explicitly control the execution of one or more Tasks (SCSI and iSCSI tasks). The Task Management functions are listed below. For a more detailed description of SCSI task management, see [SAM2]. 1 ABORT TASK - aborts the task identified by the Referenced Task Tag field. 2 ABORT TASK SET - aborts all Tasks issued via this session on the logical unit. 3 CLEAR ACA - clears the Auto Contingent Allegiance condi- tion. Julian Satran Expires August 2002 128 11iSCSI.book Page 129 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 4 CLEAR TASK SET - aborts all Tasks for the Logical Unit. 5 LOGICAL UNIT RESET 6 TARGET WARM RESET 7 TARGET COLD RESET 8 TASK REASSIGN - reassigns connection allegiance for the task identified by the Initiator Task Tag field to this con- nection, thus resuming the iSCSI exchanges for the task. For all these functions, the Task Management Function Response MUST be returned as detailed in Section 9.6 Task Management Function Response. All these functions apply to the referenced tasks regard- less of whether they are proper SCSI tasks or tagged iSCSI operations. Task management requests must act on all the commands having a CmdSN lower than the task management CmdSN. If the task management request is marked for immediate delivery it must be considered immediately for execution but the operations involved (all or part of them) may be postponed to allow the target to receive all relevant tasks. According to [SAM2] for all the tasks covered by the task management response (i.e., with CmdSN not higher than the task management command CmdSN), additional responses MUST NOT be delivered to the SCSI layer after the task management response. The iSCSI initiator MAY deliver to the SCSI layer all responses received before the task management response (i.e., it is a matter of implementation if the SCSI responses - received before the task management response but after the task man- agement request was issued - are delivered to the SCSI layer by the iSCSI layer in the initiator). The iSCSI target MUST ensure that no responses for the tasks covered by a task management function are delivered to the iSCSI initiator after the task management response. For ABORT TASK SET and CLEAR TASK SET, the issuing initiator MUST con- tinue to respond to all valid target transfer tags (received via R2T, Text Response, NOP-In, or SCSI Data-in PDUs) related to the affected task set, even after issuing the task management request. The issuing initiator SHOULD however terminate (i.e. by setting the F-bit to 1) these response sequences as quickly as possible, and it is recommended to terminate all responses with no data. The target on its part, MUST wait for responses on all affected target transfer tags before acting on either of these two task management requests. If the connection is still active (it is not undergoing an implicit or explicit logout), ABORT TASK MUST be issued on the same connection to Julian Satran Expires August 2002 129 11iSCSI.book Page 130 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 which the task to be aborted is allegiant at the time the Task Manage- ment Request is issued. If the connection is being implicitly or explicitly logged out (i.e., no other request will be issued on the failing connection and no other response will be received on the fail- ing connection), then an ABORT TASK function request may be issued on another connection. This Task Management request will then establish a new allegiance for the command to be aborted as well as abort it (i.e., the task to be aborted will not have to be retried or reas- signed, and its status, if issued but not acknowledged, will be reis- sued followed by the task management response). For the LOGICAL UNIT RESET function, the target MUST behave as dic- tated by the Logical Unit Reset function in [SAM2]. The TARGET RESET function (WARM and COLD) implementation is OPTIONAL and when implemented, should act as described below. Target Reset MAY also be subject to SCSI access controls for the requesting initiator. When authorization fails at the target, the appropriate response as described in Section 9.6 Task Management Function Response must be returned by the target. For the TARGET WARM RESET and TARGET COLD RESET functions, the target cancels all pending operations. Both functions are equivalent to the Target Reset function specified by [SAM2]. They can affect many other initiators. In addition, for the TARGET COLD RESET, the target MUST then terminate all of its TCP connections to all initiators (all sessions are termi- nated). For the TASK REASSIGN function, the target should reassign the connec- tion allegiance to this new connection (and thus resume iSCSI exchanges for the task). TASK REASSIGN MUST be received by the target ONLY after the connection on which the command was previously execut- ing has been successfully logged-out. For additional usage semantics see Section 6.1 Retry and Reassign in Recovery. TASK REASSIGN MUST be issued as an immediate command. Julian Satran Expires August 2002 130 11iSCSI.book Page 131 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.5.2 LUN This field is required for functions that address a specific LU (ABORT TASK, CLEAR TASK SET, ABORT TASK SET, CLEAR ACA, LOGICAL UNIT RESET) and is reserved in all others. 9.5.3 Referenced Task Tag The Initiator Task Tag of the task to be aborted for the ABORT TASK function or reassigned for the TASK REASSIGN function. For all the other functions this field is reserved. 9.5.4 RefCmdSN or ExpDataSN For ABORT TASK, this is the task CmdSN of the task to be aborted. If RefCmdSN does not match the CmdSN of the command to be aborted at the target, the abort action MUST NOT be performed and the response MUST be ‚ÇÖfunction rejected‚ÇÖ. If the function is TASK REASSIGN, which establishes a new connection allegiance for a previously issued Read or Bidirectional command, this field will contain the next consecutive input DataSN number expected by the initiator (no gaps) for the referenced command in a previous execution. The initiator MUST discard any discontiguous data PDUs from the previous execution and the target MUST retransmit all data previously transmitted in Data-in PDUs (if any) starting with ExpDataSN. The number of retransmitted PDUs, may or may not be the same as the original transmission, depending on if there was a change in MaxRecvPDULength in the reassignment. Otherwise, this field is reserved. Julian Satran Expires August 2002 131 11iSCSI.book Page 132 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.6 Task Management Function Response Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x22 |1| Reserved | Response | Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------------------------------------------------------+ 8/ Reserved / / / +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Referenced Task Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48| Digest (if any) | +---------------------------------------------------------------+ For the functions ABORT TASK, ABORT TASK SET, CLEAR ACA, CLEAR TASK SET, LOGICAL UNIT RESET, and TARGET WARM RESET, the target performs the requested Task Management function and sends a Task Management Response back to the initiator. 9.6.1 Response The target provides a Response, which may take on the following val- ues: a) 0 - Function Complete b) 1 - Task does not exist c) 2 - LUN does not exist. d) 3 - Task still allegiant. Julian Satran Expires August 2002 132 11iSCSI.book Page 133 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 e) 4 - Task failover not supported. f) 5 - Task management function not supported. g) 6 - Function authorization failed. h) 255 - Function Rejected. All other values are reserved. For a discussion on usage of response codes 3 and 4, see Section 6.1.2 Allegiance Reassignment. For the TARGET COLD RESET and TARGET WARM RESET functions, the target cancels all pending operations. For the TARGET COLD RESET function, the target MUST then close all of its TCP connections to all initia- tors (terminates all sessions). The mapping of the response code into a SCSI service response code, if needed, is outside the scope of this document. The response to ABORT TASK SET and CLEAR TASK SET MUST be issued by the target only after all the commands affected have been received by the target, the corresponding task management functions have been executed by the SCSI target and the delivery of all responses deliv- ered until the task management function completion have been con- firmed (acknowledged through ExpStatSN) by the initiator on all connections of this session. For the exact timeline of events, refer Section 9.6.3 Task Management actions on task sets. 9.6.2 Referenced Task Tag If the Request was ABORT TASK and the Response is "task does not exist", the Referenced Task Tag contains the Initiator Task Tag of the task that was to be aborted. In other cases, it MUST be set to 0xffffffff. 9.6.3 Task Management actions on task sets The execution of ABORT TASK SET and CLEAR TASK SET task management function requests consists of the following sequence of events in the specified order on each of the entities. The initiator: a) issues ABORT TASK SET/CLEAR TASK SET request. Julian Satran Expires August 2002 133 11iSCSI.book Page 134 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 b) continues to respond to each target transfer tag received for the affected task set. c) receives any responses for the tasks in the affected task set (may process them as usual since they are guaranteed to be valid). d) receives the task set management response, thus concluding all the tasks in the affected task set. The target: a) receives the ABORT TASK SET/CLEAR TASK SET request. b) waits for all target transfer tags to be responded and also for all affected tasks in the task set to be received. c) propagates the command up to and receives the response from the target SCSI layer. d) takes note of last-sent StatSN on each of the connections in the session, and waits for acknowledgement of each StatSN (may solicit for acknowledgement by way of a NOP-In). e) sends the task set management response. Julian Satran Expires August 2002 134 11iSCSI.book Page 135 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.7 SCSI Data-out & SCSI Data-in The SCSI Data-out PDU for WRITE operations has the following format: Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x05 |F| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| Reserved | +---------------+---------------+---------------+---------------+ 28| ExpStatSN | +---------------+---------------+---------------+---------------+ 32| Reserved | +---------------+---------------+---------------+---------------+ 36| DataSN | +---------------+---------------+---------------+---------------+ 40| Buffer Offset | +---------------+---------------+---------------+---------------+ 44| Reserved | +---------------+---------------+---------------+---------------+ 48| Digests if any... | +---------------+---------------+---------------+---------------+ / DataSegment / +/ / +---------------+---------------+---------------+---------------+ The SCSI Data-in PDU for READ operations has the following format: Julian Satran Expires August 2002 135 11iSCSI.book Page 136 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x25 |F|A|0 0 0|O|U|S| Reserved |Status or Rsvd | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| StatSN or Reserved | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36| DataSN | +---------------+---------------+---------------+---------------+ 40| Buffer Offset | +---------------+---------------+---------------+---------------+ 44| Residual Count | +---------------+---------------+---------------+---------------+ 48| Header Digest (if any) | +---------------+---------------+---------------+---------------+ / DataSegment (and digest if any) / +/ / +---------------+---------------+---------------+---------------+ Status can accompany the last Data-in PDU if the command did not end with an exception (i.e., the status is "good status" - GOOD, CONDITION MET or INTERMEDIATE CONDITION MET). The presence of status (and of a residual count) is signaled though the S flag bit. Although targets MAY choose to send even non-exception status in separate responses, initiators MUST support non-exception status in Data-In PDUs. Julian Satran Expires August 2002 136 11iSCSI.book Page 137 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.7.1 F (Final) Bit For outgoing data, this bit is 1 for the last PDU of unsolicited data or the last PDU of a sequence that answers an R2T. For incoming data, this bit is 1 for the last input (read) data PDU of a sequence. Input can be split into several sequences, each having its own F bit. Splitting the data stream into sequences does not affect DataSN counting on Data-In PDUs. It MAY be used as a "change direction" indication for Bidirectional operations that need such a change. For Bidirectional operations, the F bit is 1 for both the end of the input sequences as well as the end of the output sequences. 9.7.2 A (Acknowledge) bit For sessions with ErrorRecoveryLevel 1 or higher, the target sets this bit to 1 to indicate that it requests a positive acknowledgement from the initiator for the data received. The target should use the A bit moderately; it MAY set the A bit to 1 only once every MaxBurstSize bytes and MUST NOT do so more frequently than this. On receiving a Data-In PDU with the A bit set to 1, the initiator MUST issue a SNACK of type DataACK. If the initiator has detected holes in the input sequence, it MUST postpone issuing the SNACK of type DataACK until the holes are filled. 9.7.3 Target Transfer Tag On outgoing data, the Target Transfer Tag is provided to the target if the transfer is honoring an R2T. In this case, the Target Transfer Tag field is a replica of the Target Transfer Tag provided with the R2T. On incoming data, the Target Transfer Tag MUST be provided by the tar- get if the A bit is set to 1. The Target Transfer Tag and LUN are cop- ied by the initiator in the SNACK of type DataACK that it issues as a result of receiving a SCSI Data-in PDU with the A bit set to 1. The Target Transfer Tag values are not specified by this protocol except that the value 0xffffffff is reserved and means that the Target Transfer Tag is not supplied. If the Target Transfer Tag is provided, then the LUN field MUST hold a valid value and be consistent with Julian Satran Expires August 2002 137 11iSCSI.book Page 138 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 whatever was specified with the command; otherwise, the LUN field is reserved. 9.7.4 StatSN This field MUST ONLY be set if the S bit is set to 1. 9.7.5 DataSN For input (read) data PDUs, the DataSN is the data PDU number (start- ing with 0) within the data transfer for the command identified by the Initiator Task Tag. For output (write) data PDUs, the DataSN is the data PDU number (starting with 0) within the current output sequence. The current out- put sequence is either identified by the Initiator Task Tag (for unso- licited data) or is a data sequence generated for one R2T (for data solicited through R2T). Any input or output data sequence MUST contain less than 2**32 num- bered PDUs. 9.7.6 Buffer Offset The Buffer Offset field contains the offset of this PDU payload data within the complete data transfer. The sum of the buffer offset and length should not exceed the expected transfer length for the command. The order of data PDUs within a sequence is determined by DataPDUInOr- der. When set to Yes, it means that PDUs have to be in increasing Buffer Offset order and overlays are forbidden. The ordering between sequences is determined by DataSequenceInOrder. When set to Yes, it means that sequences have to be in increasing Buffer Offset order and overlays are forbidden. 9.7.7 DataSegmentLength This is the data payload length of a SCSI Data-In or SCSI Data-Out PDU. The sending of 0 length data segments should be avoided, but ini- tiators and targets MUST be able to properly receive 0 length data segments. Julian Satran Expires August 2002 138 11iSCSI.book Page 139 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The Data Segments of Data-in and Data-out PDUs SHOULD be filled to the integer number of 4 byte words (real payload) unless the F bit is set to 1. 9.7.8 Flags (byte 1) The last SCSI Data packet sent from a target to an initiator for a SCSI command that completed successfully (with a status of GOOD, CON- DITION MET, INTERMEDIATE or INTERMEDIATE CONDITION MET) may also optionally contain the Status for the data transfer. In this case, Sense Data cannot be sent together with the Command Status. If the command is completed with an error, then the response and sense data MUST be sent in a SCSI Response PDU (i.e., MUST NOT be sent in a SCSI Data packet). For Bidirectional commands, the status MUST be sent in a SCSI Response PDU. bit 3-5 - not used (should be set to 0). bit 1-2 - used the same as in a SCSI Response. bit 0 S (status)- set to indicate that the Command Status field contains status. If this bit is set to 1 the F bit MUST also be set to 1. The fields StatSN, Status and Residual Count have meaningful content only if the S bit is set to 1 and they values are as define in Section 9.4 SCSI Response. Julian Satran Expires August 2002 139 11iSCSI.book Page 140 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.8 Ready To Transfer (R2T) Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x31 |1| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36| R2TSN | +---------------+---------------+---------------+---------------+ 40| Buffer Offset | +---------------+---------------+---------------+---------------+ 44| Desired Data Transfer Length | +---------------------------------------------------------------+ 48| Digest (if any) | +---------------------------------------------------------------+ When an initiator has submitted a SCSI Command with data that passes from the initiator to the target (WRITE), the target may specify which blocks of data it is ready to receive. The target may request that the data blocks be delivered in whichever order is convenient for the tar- get at that particular instant. This information is passed from the target to the initiator in the Ready To Transfer (R2T) PDU. In order to allow write operations without an explicit initial R2T, the initiator and target MUST have agreed by sending the InitialR2T=No Julian Satran Expires August 2002 140 11iSCSI.book Page 141 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 key-pair to each other, which occurs either during Login or through the Text request/Response mechanism. An R2T MAY be answered with one or more SCSI Data-out PDUs with a matching Target Transfer Tag. If an R2T is answered with a single Data-out PDU, the Buffer Offset in the Data PDU MUST be the same as the one specified by the R2T. The data length of the Data PDU MUST not exceed the Desired Data Transfer Length specified in the R2T. If the R2T is answered with a sequence of Data PDUs, the Buffer Offset and Length MUST be within the range of those specified by R2T, and the last PDU SHOULD have the F bit set to 1. If the last PDU (marked with the F bit) is received before the Desired Data Transfer Length is transferred, a target MAY choose to Reject that PDU with "Protocol error" reason code. DataPDUInOrder governs the Data-Out PDU order- ing. If DataPDUInOrder is set to Yes, the Buffer Offsets and Lengths for consecutive PDUs MUST form a continuous non-overlapping range and the PDUs MUST be sent in increasing offset order. The target may send several R2T PDUs (up to a negotiated number). It, therefore, can have a number of pending data transfers. Within a con- nection, outstanding R2Ts MUST be fulfilled by the initiator in the order in which they were received. DataSequenceInOrder governs the buffer offset ordering in consecutive R2Ts. If DataSequenceInOrder is Yes, then consecutive R2Ts SHOULD refer to continuous non-overlapping ranges. 9.8.1 R2TSN R2TSN is the R2T PDU number (starting with 0) within the command iden- tified by the Initiator Task Tag. The number of R2Ts in a command MUST be less than 2**32-1. 9.8.2 StatSN The StatSN field will contain the next StatSN. The StatSN for this connection is not advanced. 9.8.3 Desired Data Transfer Length and Buffer Offset The target specifies how many bytes it wants the initiator to send because of this R2T PDU. The target may request the data from the initiator in several chunks, not necessarily in the original order of Julian Satran Expires August 2002 141 11iSCSI.book Page 142 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the data. The target, therefore, also specifies a Buffer Offset that indicates the point at which the data transfer should begin, relative to the beginning of the total data transfer. The Desired Data Transfer Length SHOULD not be 0 and MUST not exceed MaxBurstSize. 9.8.4 Target Transfer Tag The target assigns its own tag to each R2T request that it sends to the initiator. This tag can be used by the target to easily identify the data it receives. The Target Transfer Tag and LUN are copied in the outgoing data PDUs and are used by the target only. There is no protocol rule about the Target Transfer Tag, but it is assumed that it is used to tag the response data to the target (alone or in combina- tion with the LUN). Julian Satran Expires August 2002 142 11iSCSI.book Page 143 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.9 Asynchronous Message An Asynchronous Message may be sent from the target to the initiator without corresponding to a particular command. The target specifies the reason for the event and sense data. Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x32 |1| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN | + + 12| | +---------------+---------------+---------------+---------------+ 16| Reserved - 0xffffffff | +---------------+---------------+---------------+---------------+ 20| Reserved | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36| AsyncEvent | AsyncVCode | Parameter1 or Reserved | +---------------+---------------+---------------+---------------+ 40| Parameter2 or Reserved | Parameter3 or Reserved | +---------------+---------------+---------------+---------------+ 44| Reserved | +---------------+---------------+---------------+---------------+ 48| Digests if any... | +---------------+---------------+---------------+---------------+ / DataSegment - Sense Data or iSCSI Event Data / +/ / +---------------+---------------+---------------+---------------+ Some Asynchronous Messages are strictly related to iSCSI while others are related to SCSI [SAM2]. Julian Satran Expires August 2002 143 11iSCSI.book Page 144 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 StatSN counts this PDU as an acknowledgeable event (StatSN is advanced), which allows for initiator and target state synchroniza- tion. 9.9.1 AsyncEvent The codes used for iSCSI Asynchronous Messages (Events) are: 0 - a SCSI Asynchronous Event is reported in the sense data. Sense Data that accompanies the report, in the data segment, identifies the condition. The sending of a SCSI Event (Asyn- chronous Event Notification in SCSI terminology) is controlled by a SCSI Control Mode Page bit. 1 - target requests Logout. This Async Message MUST be sent on the same connection as the one requesting to be logged out. The initiator MUST honor this request by issuing a Logout as early as possible, but no later than Parameter3 seconds. Initiator MUST send a Logout with a reason code of "Close the connection" (if not the only connection) OR "Close the session" (if using multiple connections). Once this message is received, the initiator SHOULD NOT issue new iSCSI commands. The target MAY reject any new I/O requests that it receives after this Message with the reason code "Waiting for Logout". If the initiator does not Logout in Parameter3 seconds, the target should send an Async PDU with iSCSI event code "Dropped the connection" if possible, or simply terminate the transport connection. Parameter1 and Parameter2 are reserved. 2 - target indicates it will drop the connection. The Parameter1 field indicates the CID of the connection going to be dropped. The Parameter2 field (Time2Wait) indicates, in seconds, the minimum time to wait before attempting to reconnect or reas- sign. The Parameter3 field (Time2Retain) indicates the maximum time allowed to reconnect and/or reassign commands after the ini- tial wait (in Parameter2). If the initiator does not attempt to reconnect and/or reassign the outstanding commands within the time specified by Parameter3, or if Parameter3 is 0, the target will terminate all outstanding commands on this connection; no other responses should be expected from the target for the outstand- ing commands on this connection in this case. A value of 0 for Parameter2 indicates that reconnect can be attempted immediately. Julian Satran Expires August 2002 144 11iSCSI.book Page 145 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 3 - target indicates it will drop all the connections of this session. Parameter1 field is reserved. The Parameter2 field (Time2Wait) indicates, in seconds, the minimum time to wait before attempting to reconnect. The Parameter3 field (Time2Retain) indicates the maximum time allowed to reconnect and/or reassign commands after the ini- tial wait (in Parameter2). If the initiator does not attempt to reconnect and/or reassign the outstanding commands within the time specified by Parameter3, or if Parameter3 is 0, the session is terminated. In this case, the target will terminate all outstanding com- mands in this session; no other responses should be expected from the target for the outstanding commands in this session. A value of 0 for Parameter2 indicates that reconnect can be attempted immediately. 255 - vendor specific iSCSI Event. The AsyncVCode details the vendor code, and data MAY accompany the report. All other event codes are reserved. 9.9.2 AsyncVCode AsyncVCode is a vendor specific detail code that is valid only if the AsyncEvent field indicates a vendor specific event. Otherwise, it is reserved. 9.9.3 Sense Data or iSCSI Event Data For a SCSI Event, this data accompanies the report in the data segment and identifies the condition. For an iSCSI Event, additional vendor-unique data MAY accompany the Async event. Initiators MAY ignore the data when not understood while processing the rest of the PDU. Julian Satran Expires August 2002 145 11iSCSI.book Page 146 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.10 Text Request The Text Request is provided to allow for the exchange of information and for future extensions. It permits the initiator to inform a target of its capabilities or to request some special operations. An initiator MUST have only one outstanding Text Request on a connec- tion at any given time. Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|I| 0x04 |F| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| CmdSN | +---------------+---------------+---------------+---------------+ 28| ExpStatSN | +---------------+---------------+---------------+---------------+ 32/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48| Digests if any | +---------------+---------------+---------------+---------------+ / DataSegment (Text) / +/ / +---------------+---------------+---------------+---------------+ 9.10.1 F (Final) Bit When set to 1, indicates that this is the last or only text request in a sequence of commands; otherwise, it indicates that more commands will follow. Julian Satran Expires August 2002 146 11iSCSI.book Page 147 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.10.2 Initiator Task Tag The initiator assigned identifier for this Text Request. If the command is sent as part of a sequence of text requests and responses, the Initiator Task Tag MUST be the same for all the requests within the sequence (similar to linked SCSI commands). 9.10.3 Target Transfer Tag When the Target Transfer Tag is set to the reserved value 0xffffffff, it tells the target that this is a new request and the target should reset any internal state associated with the Initiator Task Tag. The target sets the Target Transfer Tag in a text response to a value other than the reserved value 0xffffffff whenever it indicates that it has more data to send or more operations to perform that are associ- ated with the specified Initiator Task Tag. It MUST do so whenever it sets the F bit to 0 in the response. By copying the Target Transfer Tag from the response to the next Text Request, the initiator tells the target to continue the operation for the specific Initiator Task Tag. The initiator MUST ignore the Target Transfer Tag in the Text Response when the F bit is set to 1. This mechanism allows the initiator and target to transfer a large amount of textual data over a sequence of text-command/text-response exchanges or to perform extended negotiation sequences. If the Target Transfer Tag is not 0xffffffff the LUN field must be the one sent by the target in the Text Response. A target MAY reset its internal state if an exchange is stalled by the initiator for a long time or if it is running out of resources. Long text responses are handled as in the following example: I->T Text SendTargets=all (F=1,TTT=0xffffffff) T->I Text (F=0,TTT=0x12345678) I->T Text (F=1, TTT=0x12345678) T->I Text (F=0, TTT=0x12345678) I->T Text (F=1, TTT=0x12345678) ... T->I Text (F=1, TTT=0xffffffff) Julian Satran Expires August 2002 147 11iSCSI.book Page 148 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.10.4 Text The data lengths of a text request MUST NOT exceed the iSCSI target MaxRecvPDULength (a per connection and per direction negotiated parameter). The text format is specified in Section 4.2 Text Mode Negotiation. Chapter 10 and Chapter 11 list some basic Text key=value pairs, some of which can be used in Login Request/Response and some in Text Request/Response. A Key=value pair can span Text request or response boundaries (i.e., a key=value pair can start in one PDU and continue on the next). The target responds by sending its response back to the initiator. The response text format is similar to the request text format. As text for text requests and responses can span several PDUs (e.g., if the PDU length does not allow the whole text to be contained in a single PDU), the text response MAY refer to key=value pairs presented in an earlier text request and the text in the request may refer to earlier responses. Text operations are usually meant for parameter setting/negotiations, but can also be used to perform some long lasting operations. Text operations that take a long time should be placed in their own Text request. Julian Satran Expires August 2002 148 11iSCSI.book Page 149 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.11 Text Response The Text Response PDU contains the target's responses to the initia- tor's Text request. The format of the Text field matches that of the Text request. Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x24 |F| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48| Digests if any... | +---------------+---------------+---------------+---------------+ / DataSegment (Text) / +/ / +---------------+---------------+---------------+---------------+ 9.11.1 F (Final) Bit When set to 1, in response to a text request with the Final bit set to 1, the F bit indicates that the target has finished the whole opera- tion. Otherwise, if set to 0 in response to a text request with the Final Bit set to 1, it indicates that the target has more work to do (invites a follow-on text request). A text response with the F bit Julian Satran Expires August 2002 149 11iSCSI.book Page 150 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 set to 1 in response to a text request with the F bit set to 0 is a protocol error. A text response with the F bit set to 1 MUST NOT contain key=value pairs that may require additional answers from the initiator. A text response with the F bit set to 1 MUST have a Target Transfer Tag field set to the reserved value of 0xffffffff. A text response with the F bit set to 0 MUST have a Target Transfer Tag field set to a value other than the reserved 0xffffffff. 9.11.2 Initiator Task Tag The Initiator Task Tag matches the tag used in the initial Text request. 9.11.3 Target Transfer Tag When a target has more work to do (e.g., cannot transfer all the remaining text data in a single Text response or has to continue the negotiation) and has enough resources to proceed, it MUST set the Tar- get Transfer Tag to a value other than the reserved value of 0xffffffff. Otherwise the Target Transfer Tag MUST be set to 0xffffffff. When the Target Transfer Tag is not 0xffffffff the LUN field may be significant. The initiator MUST copy the Target Transfer Tag and LUN in its next request to indicate that it wants the rest of the data. If the target receives a Text Request with the Target Transfer Tag set to the reserved value of 0xffffffff, it discards its internal informa- tion (resets state) associated with the given Initiator Task Tag. When a target cannot finish the operation in a single text response, and does not have enough resources to continue it rejects the Text request with the appropriate Reject code. A target may reset its internal state associated with an Initiator Task Tag, state expressed through the Target Transfer Tag if the initiator fails to continue the exchange for some time. The target may reject subsequent Text requests with the Target Transfer Tag set to the "stale" value. Julian Satran Expires August 2002 150 11iSCSI.book Page 151 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.11.4 Text Response Data The data lengths of a text response MUST NOT exceed the iSCSI initia- tor MaxRecvPDULength (a per connection and per direction negotiated parameter). The text format is specified in Section 4.2 Text Mode Negotiation. Chapter 10 and Chapter 11 list some basic Text key=value pairs, some of which can be used in Login Request/Response and some in Text Request/Response. As text for text requests and responses can span several PDUs (e.g., if the PDU length does not allow the whole text to be contained in a single PDU) the text response MAY refer to key=value pairs presented in an earlier text request. Although the initiator is the requesting party and controls the request-response initiation and termination, the target can offer key=value pairs of its own as part of a sequence and not only in response to the initiator. Julian Satran Expires August 2002 151 11iSCSI.book Page 152 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.12 Login Request After establishing a TCP connection between an initiator and a target, the initiator MUST start a Login phase to gain further access to the target's resources. The Login Phase (see Chapter 4) consists of a sequence of Login requests and responses that carry the same Initiator Task Tag. Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x03 |T|0|0 0|CSG|NSG| Version-max | Version-min | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| ISID | + +---------------+---------------+ 12| |TSID | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| CID | Reserved | +---------------+---------------+---------------+---------------+ 24| CmdSN | +---------------+---------------+---------------+---------------+ 28| ExpStatSN or Reserved | +---------------+---------------+---------------+---------------+ 32| Reserved | +---------------+---------------+---------------+---------------+ 36| Reserved | +---------------+---------------+---------------+---------------+ 40/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48/ DataSegment - Login Parameters in Text request Format / +/ / +---------------+---------------+---------------+---------------+ 9.12.1 T (Transit) Bit If set to 1, indicates that the initiator is ready to transit to the next stage. Julian Satran Expires August 2002 152 11iSCSI.book Page 153 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 If the T bit is set to 1 and NSG is FullFeaturePhase, then this also indicates that the initiator is ready for the Final Login Response (see Chapter 4). 9.12.2 CSG and NSG Through these fields, Current Stage (CSG) and Next Stage (NSG), the Login negotiation commands and responses are associated with a spe- cific stage in the session (SecurityNegotiation, LoginOperationalNe- gotiation, FullFeaturePhase) and may indicate the next stage they want to move to (see Chapter 4). The next stage value is valid only when the T bit is 1; otherwise, it is reserved. The stage codes are: - 0 - SecurityNegotiation - 1 - LoginOperationalNegotiation - 3 - FullFeaturePhase 9.12.3 Version-max Maximum Version number supported. All Login requests within the Login phase MUST carry the same Version- max. The target MUST use the value presented with the first login request. 9.12.4 Version-min Minimum Version supported. The version number of the current draft is 0x00. All Login requests within the Login phase MUST carry the same Version- min. The target MUST use the value presented with the first login request. 9.12.5 ISID This is an initiator-defined component of the session identifier (SSID) and is structured as follows (see [NDT] and Section 8.1.1 Con- servative Reuse of ISIDs for details): Julian Satran Expires August 2002 153 11iSCSI.book Page 154 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0| T | A | B | C | +---------------+---------------+---------------+---------------+ 4| D | +---------------+---------------+ The T field identifies the format and usage of A, B, C & D as indi- cated bellow: T 00b OUI-format A&B are a 22 bit OUI (the I/G & U/L omitted) C&D 24 bit qualifier 01b EN - format (IANA Enterprise Number) A - reserved B&C EN (IANA Enterprise Number) D - Qualifier 10b "Random" A - reserved B&C Random D - Qualifier 11b A,B,C&D Reserved For the T field values 00b and 01b a combination of A and B (for 00b) or B and C (for 01b) identifies the vendor or organization whose com- ponent (software or hardware) generates this ISID. A vendor or orga- nization with one or more OUIs, or one or more Enterprise Numbers, MUST use at least one of these numbers and select the appropriate value for the T field when its components generate ISIDs. An OUI or EN MUST be set in the corresponding fields in network byte order (byte big-endian). If the T field is 10b, B and C are set to a random 24bit unsigned integer value in network byte order (byte big-endian). See [NDT] for how this affects the principle of "conservative reuse". The Qualifier field is a 16 or 24 bit unsigned integer value that pro- vides a range of possible values for the ISID within the selected namespace. It may be set to any value, within the constraints speci- Julian Satran Expires August 2002 154 11iSCSI.book Page 155 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 fied in the iSCSI protocol (see Section 2.4.3 Consequences of the Model and Section 8.1.1 Conservative Reuse of ISIDs). The T field of 11 is reserved. If the ISID is derived from something assigned to a hardware adapter or interface by a vendor, as a preset default value, it MUST be con- figurable to a value assigned according to the SCSI port behavior desired by the system in which it is installed (see Section 8.1.1 Con- servative Reuse of ISIDs and Section 8.1.2 iSCSI Name and ISID/TSID Use) and the resultant ISID MUST also be persistent over power cycles, reboot, card swap etc.. 9.12.6 TSID The TSID is the target assigned component of the session identifier (SSID). Together with the ISID, provided by the initiator, TSID uniquely identifies the session from that specific target with that initiator. On a Login request, a TSID value of 0 indicates a request to open a new session. A non-zero TSID indicates a request to add a connection to an existing session. 9.12.7 Connection ID - CID A unique ID for this connection within the session. All Login requests within the Login phase MUST carry the same CID. The target MUST use the value presented with the first login request. A Login request with a non-zero TSID and a CID equal to that of an existing connection implies a logout of the connection followed by a Login (see Section 4.3.4 Connection reinstatement). 9.12.8 CmdSN CmdSN is either the initial command sequence number of a session (for the first Login request of a session - the "leading" login) or the command sequence number in the command stream (e.g., if the leading Julian Satran Expires August 2002 155 11iSCSI.book Page 156 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 login carries the CmdSN 123 all other Login requests carry the CmdSN 123 and the first non-immediate command also carries the CmdSN 123). The target MUST use the value presented with the first login request. 9.12.9 ExpStatSN This is ExpStatSN for the old connection. This field is valid only if the Login request restarts a connection (see Section 4.3.4 Connection reinstatement). 9.12.10 Login Parameters The initiator MAY provide some basic parameters in order to enable the target to determine if the initiator may use the target's resources and the initial text parameters for the security exchange. All the rules specified in Section 9.10.4 Text for text requests/ responses also hold for login requests/responses. Keys and their explanations are listed in Chapter 10 (security negotiation keys) and Chapter 11 (operational parameter negotiation keys). All keys in Chapter 11, except for the X- extension format, MUST be supported by iSCSI initiators and targets. Keys in Chapter 10, only need to be sup- ported when the function to which they refer is mandatory to imple- ment. Julian Satran Expires August 2002 156 11iSCSI.book Page 157 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.13 Login Response The Login Response indicates the progress and/or end of the login phase. Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x23 |T|0 0 0|CSG|NSG| Version-max | Version-active| +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| ISID | + +---------------+---------------+ 12| |TSID | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Reserved | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36| Status-Class | Status-Detail | Reserved | +---------------+---------------+---------------+---------------+ 40/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48/ DataSegment - Login Parameters in Text request Format / +/ / +---------------+---------------+---------------+---------------+ 9.13.1 Version-max This is the highest version number supported by the target. All Login responses within the Login phase MUST carry the same Ver- sion-max. Julian Satran Expires August 2002 157 11iSCSI.book Page 158 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The initiator MUST use the value presented as a response to the first login request. 9.13.2 Version-active Indicates the highest version supported by the target and initiator. If the target does not support a version within the range specified by the initiator, the target rejects the login and this field indicates the lowest version supported by the target. All Login responses within the Login phase MUST carry the same Ver- sion-active. The initiator MUST use the value presented as a response to the first login request. 9.13.3 TSID The TSID is the target assigned component of the session identifier (SSID). TSID MUST be valid only in the final response. The target is generating and using it and its internal format and content are not defined by this protocol except for the value 0 that is reserved and used by the initiator to indicate a new session. It is given to the target, during additional connection establishment for the same ses- sion, to identify the associated session for the target. 9.13.4 StatSN For the first Login Response (the response to the first Login Request), this is the starting status Sequence Number for the connec- tion. The next response of any kind, including the next login response, if any, in the same login phase, will carry this number + 1. This field is valid only if the Status-Class is 0. 9.13.5 Status-Class and Status-Detail The Status returned in a Login Response indicates the execution status of the login phase. The status includes: Status-Class Status-Detail 0 Status-Class indicates success. Julian Satran Expires August 2002 158 11iSCSI.book Page 159 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 A non-zero Status-Class indicates an exception. In this case, Status- Class is sufficient for a simple initiator to use when handling errors, without having to look at the Status-Detail. The Status- Detail allows finer-grained error recovery for more sophisticated initiators, as well as better information for error logging. The status classes are as follows: 0 - Success - indicates that the iSCSI target successfully received, understood, and accepted the request. The numbering fields (StatSN, ExpCmdSN, MaxCmdSN) are valid only if Status- Class is 0. 1 - Redirection - indicates that the initiator must take further action to complete the request. This is usually due to the target moving to a different address. All of the redirection status class responses MUST return one or more text key param- eters of the type "TargetAddress", which indicates the tar- get's new address. 2 - Initiator Error (not a format error) - indicates that the initiator most likely caused the error. This MAY be due to a request for a resource for which the initiator does not have permission. The request should not be tried again. 3 - Target Error - indicates that the target sees no errors in the initiator's login request, but is currently incapable of fulfilling the request. The client may re-try the same login request later. The table below shows all of the currently allocated status codes. The codes are in hexadecimal; the first byte is the status class and the second byte is the status detail. Julian Satran Expires August 2002 159 11iSCSI.book Page 160 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 ----------------------------------------------------------------- Status | Code | Description |(hex) | ----------------------------------------------------------------- Success | 0000 | Login is proceeding OK (*1). ----------------------------------------------------------------- Target Moved | 0101 | The requested iSCSI Target Name (ITN) Temporarily | | has temporarily moved | | to the address provided. ----------------------------------------------------------------- Target Moved | 0102 | The requested ITN has permanently moved Permanently | | to the address provided. ----------------------------------------------------------------- Initiator | 0200 | Miscellaneous iSCSI initiator Error | | errors. ---------------------------------------------------------------- Authentication| 0201 | The initiator could not be Failure | | successfully authenticated. ----------------------------------------------------------------- Authorization | 0202 | The initiator is not allowed access Failure | | to the given target. ----------------------------------------------------------------- Not Found | 0203 | The requested ITN does not | | exist at this address. ----------------------------------------------------------------- Target Removed| 0204 | The requested ITN has been removed and | |no forwarding address is provided. ----------------------------------------------------------------- Unsupported | 0205 | The requested iSCSI version range is Version | | not supported by the target. ----------------------------------------------------------------- Too many | 0206 | No more connections are accepted on this SID. connections | | ----------------------------------------------------------------- Missing | 0207 | Missing parameters (e.g., iSCSI parameter | | Initiator and/or Target Name). ----------------------------------------------------------------- Can't include | 0208 | Target does not support session in session | | spanning to this connection (address) ----------------------------------------------------------------- Session type | 0209 | Target does not support this type of Not supported | | of session or not from this Initiator. ----------------------------------------------------------------- Julian Satran Expires August 2002 160 11iSCSI.book Page 161 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Session does | 020a | Attempt to add a connection not exist | | to an inexistent session ----------------------------------------------------------------- Invalid during| 020b | Invalid Request type during Login login | | ----------------------------------------------------------------- Target Error | 0300 | Target hardware or software error. ----------------------------------------------------------------- Service | 0301 | The iSCSI service or target is not Unavailable | | currently operational. ----------------------------------------------------------------- Out of | 0302 | The target has insufficient session, Resources | | connection, or other resources. ----------------------------------------------------------------- (*1)If the response T bit is 1 and the NSG is FullFeaturePhase in both the request and the response the login phase is finished and the ini- tiator may proceed to issue SCSI commands. If the Status Class is not 0, the initiator and target MUST close the TCP connection. If the target wishes to reject the login request for more than one reason, it should return the primary reason for the rejection. 9.13.6 T (Transit) bit The T bit is set to 1 as an indicator of the end of the stage. If the T bit is set to 1 and NSG is FullFeaturePhase, then this is also the Final Login Response (see Chapter 4). A T bit of 0 indicates a "par- tial" response, which means "more negotiation needed". A login response with a T bit set to 1 MUST NOT contain key=value pairs that may require additional answers from the initiator within the same stage. If the status class is 0, the T bit MUST NOT be set to 1 if the T bit in the request was set to 0. Julian Satran Expires August 2002 161 11iSCSI.book Page 162 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.14 Logout Request The Logout request is used to perform a controlled closing of a con- nection. An initiator MAY use a logout command to remove a connection from a session or to close an entire session. After sending the Logout PDU, an initiator MUST NOT send any new iSCSI commands on the closing connection. If the Logout is intended to close the session, new iSCSI commands MUST NOT be sent on any of the connec- tions participating in the session. When receiving a Logout request with the reason code of "close the connection" or "close the session", the target MUST abort all pending commands, whether acknowledged or not, on that connection or session respectively. When receiving a Logout request with the reason code "remove connection for recovery", the target MUST discard all requests not yet acknowledged that were issued on the specified con- nection and suspend all data/status/R2T transfers on behalf of pend- ing commands on the specified connection. The target then issues the Logout response and half-closes the TCP connection (sends FIN). After receiving the Logout response and attempting to receive the FIN (if still possible), the initiator MUST completely close the logging-out connection. For the aborted commands, no additional responses should be expected. A Logout for a CID may be performed on a different transport connec- tion when the TCP connection for the CID has already been terminated. In such a case, only a logical "closing" of the iSCSI connection for the CID is implied with a Logout. All commands that were not aborted or not completed (with status) and acknowledged when the connection is closed completely can be reas- signed to a new connection if the target supports connection recovery. If an initiator intends to start recovery for a failing connection, it MUST use either the Logout command to "clean-up" the target end of a failing connection and enable recovery to start, or use the restart option of the Login command for the same effect. In sessions with a single connection, this may imply the opening of a second connection with the sole purpose of cleaning-up the first. In this case, the restart option of the Login should be used. Julian Satran Expires August 2002 162 11iSCSI.book Page 163 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Sending a logout request with the reason code of "close the connec- tion" or "remove the connection for recovery" may result in the dis- carding of some unacknowledged commands. Those holes in command sequence numbers will have to be handled by appropriate recovery (see Chapter 6) unless the session is also closed. Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|I| 0x06 |1| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------------------------------------------------------+ 8/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 12| Reserved | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| CID or Reserved | Reserved |Reason Code | +---------------+---------------+---------------+---------------+ 24| CmdSN | +---------------+---------------+---------------+---------------+ 28| ExpStatSN | +---------------+---------------+---------------+---------------+ 32/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48| Digest (if any) | +---------------------------------------------------------------+ 9.14.1 CID This is the connection ID of the connection to be closed (including closing the TCP stream). This field is valid only if the reason code is not "close the session". 9.14.2 ExpStatSN This is the last ExpStatSN value for the connection to be closed. Julian Satran Expires August 2002 163 11iSCSI.book Page 164 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.14.3 Reason Code Indicates the reason for Logout: 0 - closes the session. All commands associated with the session (if any) are aborted. 1 - closes the connection. All commands associated with connec- tion (if any) are aborted. 2 - removes the connection for recovery. Connection is closed and all commands associated with it, if any, are to be pre- pared for a new allegiance. Julian Satran Expires August 2002 164 11iSCSI.book Page 165 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.15 Logout Response The logout response is used by the target to indicate if the cleanup operation for the connection(s) has completed. After Logout, the TCP connection referred by the CID MUST be closed at both ends (or all connections must be closed if the logout reason was session close). Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x26 |1| Reserved | Response | Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------------------------------------------------------+ 8/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag | +---------------+---------------+---------------+---------------+ 20| Reserved | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36| Reserved | +---------------------------------------------------------------+ 40| Time2Wait | Time2Retain | +---------------+---------------+---------------+---------------+ 44| Reserved | +---------------+---------------+---------------+---------------+ 48| Digest (if any) | +---------------------------------------------------------------+ 9.15.1 Response Logout response: 0 - connection or session closed successfully. Julian Satran Expires August 2002 165 11iSCSI.book Page 166 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 1 - CID not found. 2 - connection recovery not supported (if Logout reason code was recovery and target does not support it- as indicated by the ErrorRecoveryLevel. 3 - cleanup failed for various reasons. 9.15.2 Time2Wait If the Logout response code is 0 and if the operational ErrorRecovery- Level is 2, this is the minimum amount of time, in seconds, to wait before attempting task reassignment. If the Logout response code is 0 and if the operational ErrorRecoveryLevel is less than 2, this field is to be ignored. This field is invalid if the Logout response code is 1. If the Logout response code is 2 or 3, this field specifies the mini- mum time to wait before attempting a new implicit or explicit logout. If Time2Wait is 0, the reassignment or a new Logout may be attempted immediately. 9.15.3 Time2Retain If the Logout response code is 0 and if the operational ErrorRecovery- Level is 2, this is the maximum amount of time, in seconds, after the initial wait (Time2Wait), the target waits for the allegiance reas- signment for any active task after which the task state is discarded. If the Logout response code is 0 and if the operational ErrorRecovery- Level is less than 2, this field is to be ignored. This field is invalid if the Logout response code is 1. If the Logout response code is 2 or 3, this field specifies the maxi- mum amount of time, in seconds, after the initial wait (Time2Wait),the target waits for a new implicit or explicit logout. If it is the last connection of a session, the whole session state is discarded after Time2Retain. Julian Satran Expires August 2002 166 11iSCSI.book Page 167 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 If Time2Retain is 0, the target had already discarded the connection (and possibly the session) state along with the task states. No reas- signment or Logout is required in this case. Julian Satran Expires August 2002 167 11iSCSI.book Page 168 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.16 SNACK Request Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x10 |1|Rsrvd| Type | Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| Reserved | +---------------+---------------+---------------+---------------+ 28| ExpStatSN | +---------------+---------------+---------------+---------------+ 32/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 40| BegRun | +---------------------------------------------------------------+ 44| RunLength | +---------------------------------------------------------------+ 48| Digest (if any) | +---------------------------------------------------------------+ Support for SNACK is optional. The SNACK request is used to request the retransmission of numbered- responses, data, or R2T PDUs from the target. The SNACK request indi- cates the missed numbered-response or data "run" to the target, where the run starts with the first missed StatSN, DataSN, or R2TSN and indicates also the number of missed Status, Data, or R2T PDUs (0 has the special meaning of "all after the initial"). The numbered-response(s) or R2T(s), requested by a SNACK, MUST be delivered as exact replicas of the ones the initiator missed and MUST Julian Satran Expires August 2002 168 11iSCSI.book Page 169 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 include all its flags. However, the fields ExpCmdSN, MaxCmdSN and Exp- DataSN MUST carry the current values. The numbered Data-In PDUs, requested by a SNACK with a RunLength dif- ferent from 0, have to be delivered as exact replicas of the ones the initiator missed and MUST include all its flags. However, the fields ExpCmdSN and MaxCmdSN MUST carry the current values. Data-In PDUs requested with RunLength 0 (meaning all PDUs after this number) may be different from the ones originally sent, in order to reflect changes in MaxRecvPDULength. Any SNACK that requests a numbered-response, Data, or R2T that was not sent by the target MUST be rejected with a reason code of "Protocol error". 9.16.1 Type This field encodes the SNACK function as follows: 0-Data/R2T SNACK - requesting retransmission of a Data-In or R2T PDU. 1-Status SNACK - requesting retransmission of a numbered response. 2-DataACK - positively acknowledges Data-In PDUs. All other values are reserved. Data/R2T SNACK for a command MUST precede status acknowledgement for the given command. For Status SNACK, the Initiator Task Tag is reserved. In all other cases, the Initiator Task Tag field MUST be set to the Initiator Task Tag of the referenced command. For DataACK, the Target Transfer Tag has to contain a copy of the Tar- get Transfer Tag and LUN provided with the SCSI Data-In PDU with the A bit set to 1. In all other cases, the Target Transfer Tag field MUST be set to the reserved value of 0xffffffff. An iSCSI target that does not support recovery within connection MAY discard the status SNACK. If the target supports recovery within con- nection, it MAY discard the SNACK after which it MUST issue an Asyn- Julian Satran Expires August 2002 169 11iSCSI.book Page 170 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 chronous Message PDU with an iSCSI event that indicates "Request Logout". If an initiator operates at ErrorRecoveryLevel 1 or higher, it MUST issue a SNACK of type DataACK after receiving a Data-In PDU with the A bit set to 1. However, if the initiator has detected holes in the input sequence, it MUST postpone issuing the SNACK of type DataACK until the holes are filled. An initiator MAY ignore the A bit if it deems that the bit is being set aggressively by the target (i.e., before the MaxBurstSize limit is reached). The DataACK is used to free resources at the target and not to request or imply data retransmission. 9.16.2 BegRun The first missed DataSN, R2TSN, or StatSN or the next expected DataSN for a DataACK type SNACK request. 9.16.3 RunLength The number of sequential missed DataSN, R2TSN or StatSN. RunLength of "0" signals that all Data-In, R2T or Response PDUs carrying the num- bers equal to or greater to BegRun have to be resent. The first data SNACK, issued after initiator‚ÇÖs MaxRecvPDULength decreased, for a command issued on the same connection before the change in MaxRecvPDULength, MUST use RunLength "0" to request retransmission of any number of PDUs (including one). The number of retransmitted PDUs in this case, may or may not be the same as the original transmission, depending on whether loss was before or after the MaxRecvPDULength was changed at the target. Julian Satran Expires August 2002 170 11iSCSI.book Page 171 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.17 Reject Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x3f |1| Reserved | Reason | Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 16| Reserved - 0xffffffff | +---------------+---------------+---------------+---------------+ 20| Reserved | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36| DataSN or Reserved | +---------------+---------------+---------------+---------------+ 40| Reserved | +---------------+---------------+---------------+---------------+ 44| Reserved | +---------------+---------------+---------------+---------------+ 48| Digest (if any) | +---------------+---------------+---------------+---------------+ xx/ Complete Header of Bad PDU / +/ / +---------------+---------------+---------------+---------------+ yy/Vendor specific data (if any) / / / +---------------+---------------+---------------+---------------+ zz| Digest (if any) | +---------------+---------------+---------------+---------------+ Reject is used to indicate an iSCSI error condition (protocol, unsup- ported option etc.). Julian Satran Expires August 2002 171 11iSCSI.book Page 172 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.17.1 Reason The reject Reason is coded as follows: +------+-----------------------------------------+------------------+ | Code | Explanation | Can the original | | (hex)| | PDU be re-sent? | +------+-----------------------------------------+------------------+ | 0x01 | Reserved | no | | | | | | 0x02 | Data (payload) Digest Error | yes (Note 1) | | | | | | 0x03 | Data-SNACK Reject | yes | | | | | | 0x04 | Protocol Error (e.g., SNACK request for | no | | | a status that was already acknowledged | | | | | | | 0x05 | Command not supported in this session | no | | | type | | | | | | | 0x06 | Immediate Command Reject - too many | yes | | | immediate commands | | | | | | | 0x07 | Task in progress | no | | | | | | 0x08 | Invalid Data ACK | no | | | | | | 0x09 | Invalid PDU field | no (Note 2) | | | | | | 0x0a | Long Operation Reject - Can't generate | yes | | | Target Transfer Tag - out of resources | | | | | | | 0x0b | Negotiation Reset | no | | | | | | 0x0c | Waiting for Logout | no | +------+-----------------------------------------+------------------+ Note 1: For iSCSI Data-Out PDU retransmission is done only if the tar- get requests retransmission with a recovery R2T. However, if this is the data digest error on immediate data, the initiator may choose to retransmit the whole PDU including the immediate data. Julian Satran Expires August 2002 172 11iSCSI.book Page 173 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Note 2: A target should use this reason code for all invalid values of PDU fields that are meant to describe a task or a data transfer. Some examples are invalid TTT/ITT, buffer offset, LUN qualifying a TTT. All other values for Reason are reserved. In all the cases in which a pre-instantiated SCSI task is terminated because of the reject, the target must issue a proper SCSI command response with CHECK CONDITION as described in Section 9.4.3 Response. In those cases in which a status for the SCSI task was already sent before the reject no additional status is required. If the error is detected while data from the initiator is still expected (the command PDU did not contain all the data and the target has not received a Data-out PDU with the Final bit 1), the target MUST wait until it receives the Data-out PDU with the F bit set to 1 before sending the Response PDU. For additional usage semantics of Reject PDU, see Section 6.2 Usage Of Reject PDU in Recovery. 9.17.2 DataSN This field is valid only if the Reason code is "Protocol error" and the SNACK was a Data/R2T SNACK. The DataSN/R2TSN is the last valid sequence number that the target sent for the task. 9.17.3 StatSN, ExpCmdSN and MaxCmdSN Those fields carry their usual values and are not related to the rejected command 9.17.4 Complete Header of Bad PDU The target returns the header (not including digest) of the PDU in error as the data of the response. Julian Satran Expires August 2002 173 11iSCSI.book Page 174 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.18 NOP-Out Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|I| 0x00 |1| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| CmdSN | +---------------+---------------+---------------+---------------+ 28| ExpStatSN | +---------------+---------------+---------------+---------------+ 32/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48| Digests if any... | +---------------+---------------+---------------+---------------+ / DataSegment - Ping Data (optional) / +/ / +---------------+---------------+---------------+---------------+ A NOP-Out may be used by an initiator as a "ping command" to verify that a connection/session is still active and all its components are operational. The NOP-In response is the "ping echo". A NOP-Out is also sent by an initiator in response to a NOP-In. A NOP-Out may also be used to confirm a changed ExpStatSN if another PDU will not be available for a long time. When used as a ping command, the Initiator Task Tag MUST be set to a valid value (not the reserved 0xffffffff). Julian Satran Expires August 2002 174 11iSCSI.book Page 175 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Upon receipt of a NOP-In with the Target Transfer Tag set to a valid value (not the reserved 0xffffffff), the initiator MUST respond with a NOP-Out. In this case, the NOP-Out Target Transfer Tag MUST contain a copy of the NOP-In Target Transfer Tag. When a target receives the NOP-Out with a valid Initiator Task Tag, it MUST respond with a Nop-In Response (see NOP-In). 9.18.1 Initiator Task Tag An initiator assigned identifier for the operation. The NOP-Out must have the Initiator Task Tag set to a valid value only if a response in the form of NOP-In is requested. If the Initiator Task Tag contains 0xffffffff, the CmdSN field con- tains the next CmdSN. However, CmdSN is not advanced and the I bit must be set to 1. 9.18.2 Target Transfer Tag A target assigned identifier for the operation. The NOP-Out MUST have the Target Transfer Tag set only if it is issued in response to a NOP-In with a valid Target Transfer Tag. In this case, it copies the Target Transfer Tag from the NOP-In PDU. When the Target Transfer Tag is set, the LUN field MUST also be copied from the NOP-In. 9.18.3 Ping Data Ping data is reflected in the NOP-In Response. The length of the reflected data is limited to MaxRecvPDULength. The length of ping data is indicated by the Data Segment Length. 0 is a valid value for the Data Segment Length and indicates the absence of ping data. Julian Satran Expires August 2002 175 11iSCSI.book Page 176 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 9.19 NOP-In Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0|.|.| 0x20 |1| Reserved | +---------------+---------------+---------------+---------------+ 4|TotalAHSLength | DataSegmentLength | +---------------+---------------+---------------+---------------+ 8| LUN or Reserved | + + 12| | +---------------+---------------+---------------+---------------+ 16| Initiator Task Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 20| Target Transfer Tag or 0xffffffff | +---------------+---------------+---------------+---------------+ 24| StatSN | +---------------+---------------+---------------+---------------+ 28| ExpCmdSN | +---------------+---------------+---------------+---------------+ 32| MaxCmdSN | +---------------+---------------+---------------+---------------+ 36/ Reserved / +/ / +---------------+---------------+---------------+---------------+ 48| Digests if any... | +---------------+---------------+---------------+---------------+ / DataSegment - Return Ping Data / +/ / +---------------+---------------+---------------+---------------+ NOP-In is either sent by a target as a response to a NOP-Out, as a "ping" to an initiator or as a means to carry a changed ExpCmdSN and/ or MaxCmdSN if another PDU will not be available for a long time (as determined by the target). When a target receives the NOP-Out with a valid Initiator Task Tag (not the reserved value 0xffffffff), it MUST respond with a NOP-In with the same Initiator Task Tag that was provided in the NOP-Out Com- mand. It MUST also duplicate up to the first MaxRecvPDULength bytes of Julian Satran Expires August 2002 176 11iSCSI.book Page 177 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 the initiator provided Ping Data. For such a response, the Target Transfer Tag MUST be 0xffffffff. When a target send a NOP-In as a "ping" (the Initiator Task Tag is 0xffffffff) it MUST NOT send any data in the data segment (DataSeg- mentLength MUST be 0). 9.19.1 Target Transfer Tag A target assigned identifier for the operation. If the target is responding to a NOP-Out, this is set to the reserved value 0xffffffff. If the target is sending a NOP-In as a Ping (intending to receive a corresponding NOP-Out), this field is set to a valid value (not the reserved 0xffffffff). If the target is initiating a NOP-In without wanting to receive a cor- responding NOP-Out, this field MUST hold the reserved value of 0xffffffff. Whenever the NOP-In is sent as a "ping" to an initiator (not as a response to a NOP-Out), the StatSN field will contain the next StatSN. However, StatSN for this connection is not advanced. 9.19.2 LUN A LUN MUST be set to a correct value when the Target Transfer Tag is valid (not the reserved value 0xffffffff). Julian Satran Expires August 2002 177 11iSCSI.book Page 178 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 10. iSCSI Security Keys and Values The following keys can only be used during the SecurityNegotiation stage of the Login Phase: SessionType InitiatorName TargetName InitiatorAlias TargetAlias AuthMethod and all keys listed under AuthMethod along with all of their associated keys. SessionType, InitiatorName, TargetName, InitiatorAlias and Tar- getAlias are described in Chapter 11 as they can be used also in the OperationalNegotiation stage. All security keys have connection-wide applicability. 10.1 AuthMethod Use: During Login - Security Negotiation Senders: Initiator and Target Scope: connection AuthMethod = The main item of security negotiation is the authentication method (AuthMethod). The authentication methods that can be used (appear in the list-of- options) are either those listed in the following table or are vendor- unique methods: Julian Satran Expires August 2002 178 11iSCSI.book Page 179 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +------------------------------------------------------------+ | Name | Description | +------------------------------------------------------------+ | KRB5 | Kerberos V5 | +------------------------------------------------------------+ | SPKM1 | Simple Public-Key GSS-API Mechanism | +------------------------------------------------------------+ | SPKM2 | Simple Public-Key GSS-API Mechanism | +------------------------------------------------------------+ | SRP | Secure Remote Password | +------------------------------------------------------------+ | CHAP | Challenge Handshake Authentication Protocol| +------------------------------------------------------------+ | None | No authentication | +------------------------------------------------------------+ KRB5 is defined in [RFC1510]. SPKM1 and SPKM2 are defined in [RFC2025]. SRP is defined in [RFC2945] and CHAP is defined in [RFC1994]. The AuthMethod selection is followed by an "authentication exchange" specific to the authentication method selected. The authentication exchange authenticates the initiator to the tar- get, and optionally, the target to the initiator. Authentication is not mandatory to use but must be supported by the target and initia- tor. The initiator and target MUST implement SRP. 10.2 Kerberos For KRB5 (Kerberos V5) [RFC1510], the initiator MUST use: KRB_AP_REQ= where KRB_AP_REQ is the client message as defined in [RFC1510]. If the initiator authentication fails, the target MUST answer with a Login reject with "Authentication Failure" status. Otherwise, if the initiator has selected the mutual authentication option (by setting MUTUAL-REQUIRED in the ap-options field of the KRB_AP_REQ), the tar- get MUST reply with: Julian Satran Expires August 2002 179 11iSCSI.book Page 180 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 KRB_AP_REP= where KRB_AP_REP is the server's response message as defined in [RFC1510]. If mutual authentication was selected and target authentication fails, the initiator MUST close the connection. KRB_AP_REQ and KRB_AP_REP are large binary items and their binary length (not the length of the character string that represents them in encoded form) MUST not exceed 65536 bytes. 10.3 Simple Public-Key Mechanism (SPKM) For SPKM1 and SPKM2 [RFC2025], the initiator MUST use: SPKM_REQ= where SPKM-REQ is the first initiator token as defined in [RFC2025]. [RFC2025] defines situations where each side may send an error token that may cause the peer to re-generate and resend its last token. This scheme is followed in iSCSI, and the error token syntax is: SPKM_ERROR= However, SPKM-DEL tokens that are defined by [RFC2025] for fatal errors will not be used by iSCSI. If the target needs to send a SPKM- DEL token(by[RFC2025], it will, instead, send a Login "login reject" message with the "Authentication Failure" status and terminate the connection. If the initiator needs to send a SPKM-DEL token, it will close the connection. In the following sections, we assume that no SPKM-ERROR tokens are required. If the initiator authentication fails, the target MUST return an error. Otherwise, if the AuthMethod is SPKM1 or if the initiator has selected the mutual authentication option (by setting mutual-state bit in the options field of the REQ-TOKEN in the SPKM-REQ), the target MUST reply with: Julian Satran Expires August 2002 180 11iSCSI.book Page 181 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 SPKM_REP_TI= where SPKM-REP-TI is the target token as defined in [RFC2025]. If mutual authentication was selected and target authentication fails, the initiator MUST close the connection. Otherwise, if the AuthMethod is SPKM1, the initiator MUST continue with: SPKM_REP_IT= where SPKM-REP-IT is the second initiator token as defined in [RFC2025]. If the initiator authentication fails, the target MUST answer with a Login reject with "Authentication Failure" status. All the SPKM-* tokens are large binary items and their binary length (not the length of the character string that represents them in encoded form) MUST not exceed 65536 bytes. 10.4 Secure Remote Password (SRP) For SRP [RFC2945], the initiator MUST use: SRP_U= TargetAuth=Yes /* or TargetAuth=No */ The target MUST answer with a Login reject with the "Authorization Failure" status or reply with: SRP_N= SRP_g= SRP_s= The initiator MUST either close the connection or continue with: SRP_A= The target MUST answer with a Login reject with the "Authentication Failure" status or reply with: SRP_B= The initiator MUST close the connection or continue with: SRP_M= Julian Satran Expires August 2002 181 11iSCSI.book Page 182 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 If the initiator authentication fails, the target MUST answer with a Login reject with "Authentication Failure" status. Otherwise, if the initiator sent TargetAuth=Yes in the first message (requiring target authentication), the target MUST reply with: SRP_HM= If the target authentication fails, the initiator MUST close the con- nection. Where U, N, g, s, A, B, M, and H(A | M | K) are defined in [RFC2945] (using the SHA1 hash function, i.e., SRP-SHA1), U is a text string, N,g,s,A,B,M, and H(A | M | K) are binary items, and their binary length (not the length of the character string that represents them in encoded form) MUST not exceed 1024 bytes. Further restrictions on allowed N,g values are specified in Section 7.2 In-band Initiator- Target Authentication. 10.5 Challenge Handshake Authentication Protocol (CHAP) For CHAP [RFC1994], the initiator MUST use: CHAP_A= Where A1,A2... are proposed algorithms, in order of preference. The target MUST answer with a Login reject with the "Authentication Failure" status or reply with: CHAP_A= CHAP_I= CHAP_C= Where A is one of A1,A2... that were proposed by the initiator. The initiator MUST continue with: CHAP_N= CHAP_R= or, if it requires target authentication, with: CHAP_N= CHAP_R= CHAP_I= CHAP_C= Julian Satran Expires August 2002 182 11iSCSI.book Page 183 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 If the initiator authentication fails, the target MUST answer with a Login reject with "Authentication Failure" status. Otherwise, if the initiator required target authentication, the target MUST reply with CHAP_N= CHAP_R= If target authentication fails, the initiator MUST close the connec- tion. Where N, (A,A1,A2), I, C, and R are (correspondingly) the Name, Algo- rithm, Identifier, Challenge, and Response as defined in [RFC1994], N is a text string, A,A1,A2, and I are numbers, and C and R are binary items and their binary length (not the length of the character string that represents them in encoded form) MUST not exceed 1024 bytes. For the Algorithm, as stated in [RFC1994], one value is required to be implemented: 5 (CHAP with MD5) To guarantee interoperability, initiators SHOULD always offer it as one of the proposed algorithms. Julian Satran Expires August 2002 183 11iSCSI.book Page 184 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 11. Login/Text Operational Keys The ISID and TSID collectively form the SSID (session id). A TSID of zero indicates a leading connection. Some session specific parameters MUST only be carried on the leading connection and cannot be changed after the leading connection login (e.g., MaxConnections, the maximum number of connections). This holds for a single connection session with regard to connection restart. The keys that fall into this cate- gory have the use LO (Leading Only). Keys that can be used only during login have the use IO (initialize only) while those that can be used in both the login phase and full feature phase have the use ALL. Keys that can only be used during full feature phase use FFPO (full feature phase only). Keys marked as "declarative" may appear also in the SecurityNegotia- tion stage while all other keys described in this chapter are opera- tional keys. Key scope is indicated as session-wide (SW) or connection-only (CO). 11.1 HeaderDigest and DataDigest Use: IO Senders: Initiator and Target Scope: CO HeaderDigest = DataDigest = Digests enable the checking of end-to-end non-cryptographic data integrity beyond the integrity checks provided by the link layers and the covering of the whole communication path including all elements that may change the network level PDUs such as routers, switches, and proxies. The following table lists cyclic integrity checksums that can be nego- tiated for the digests and that MUST be implemented by every iSCSI initiator and target. These digest options only have error detection significance. Julian Satran Expires August 2002 184 11iSCSI.book Page 185 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +---------------------------------------------+ | Name | Description | Generator | +---------------------------------------------+ | CRC32C | 32 bit CRC |0x11edc6f41| +---------------------------------------------+ | None | no digest | +---------------------------------------------+ The generator polynomial for this digest is given in hex-notation, for example 0x3b stands for 0011 1011. The polynomial x**5+X**4+x**3+x+1. When the Initiator and Target agree on a digest, this digest MUST be used for every PDU in Full Feature Phase. Padding bytes, when present, in a segment covered by a CRC, should be set to 0 and are included in the CRC. The CRC should be calculated as follows: - Data bits are assumed to form a serial bit stream in the num- bering order that appears in the draft and starts with byte 0 bit 0 to 7 continues with byte 1 bit 0 etc. (Big Endian on bytes / Little Endian on bits). This bit-stream has no rela- tion to the physical bit stream and is used to associate the data bits with specific coefficients of a binary polynomial. - The first 32 bits of the bit-stream are complemented. - The n bits of the bit-stream are considered coefficients of a polynomial M(x) of order n-1, with bit 0 of byte 0 being x^(n- 1). - The polynomial is multiplied by x^32 then divided by G(x). The generator polynomial produces a remainder R(x) of degree <= 31. - The coefficients of R(x) are considered a 32 bit sequence. - The bit sequence is complemented and the result is the CRC. - The CRC bits appear after the message bits with x^31 first followed by x^30 etc. (when examples are provided, the value to be specified in the examples follows the same rules of ordering as the rest of this document). - A receiver of a "good" segment (data or header) including the CRC built using the generator 0x11edc6f41 will get the value Julian Satran Expires August 2002 185 11iSCSI.book Page 186 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 0x1c2d19ed as its CRC (this is a polynomial value and not a word as outlined in this draft). Proprietary algorithms MAY also be negotiated for digests. Whenever a proprietary algorithm is negotiated, "None" or "CRC32C" should be listed as an option in order to guarantee interoperability. 11.2 MaxConnections Use: LO Senders: Initiator and Target Scope: SW MaxConnections= Default is 1. Initiator and target negotiate the maximum number of connections requested/acceptable. The lower of the two numbers is selected. 11.3 SendTargets Use: FFPO Senders: Initiator Scope: SW For a complete description, see Appendix D. - SendTargets Operation -. 11.4 TargetName Use: IO by initiator ALL by target, Declarative Senders: Initiator and Target Scope: SW TargetName= Examples: TargetName=iqn.1993-11.com.disk-vendor.diskarrays.sn.45678 TargetName=eui.020000023B040506 The initiator of the TCP connection must provide this key to the remote endpoint in the first login request if the initiator is not Julian Satran Expires August 2002 186 11iSCSI.book Page 187 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 establishing a discovery session. The iSCSI Target Name specifies the worldwide unique name of the target. The TargetName key may also be returned by the "SendTargets" text request (which is its only use when issued by a target). 11.5 InitiatorName Use: IO, Declarative Senders: Initiator Scope: SW InitiatorName= Examples: InitiatorName=iqn.1992-04.com.os-vendor.plan9.cdrom.12345 InitiatorName=iqn.2001-02.com.ssp.users.customer235.host90 InitiatorName=iSCSI The initiator of the TCP connection must provide this key to the remote endpoint at the first Login of the login phase for every con- nection. The Initiator key enables the initiator to identify itself to the remote endpoint. 11.6 TargetAlias Use: ALL, Declarative Senders: Target Scope: SW TargetAlias= Examples: TargetAlias=Bob-s Disk TargetAlias=Database Server 1 Log Disk TargetAlias=Web Server 3 Disk 20 If a target has been configured with a human-readable name or descrip- tion, this name MUST be communicated to the initiator during a Login Response PDU. This string is not used as an identifier, but can be displayed by the initiator's user interface in a list of targets to which it is connected. Julian Satran Expires August 2002 187 11iSCSI.book Page 188 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 11.7 InitiatorAlias Use: ALL, Declarative Senders: Initiator Scope: SW InitiatorAlias= Examples: InitiatorAlias=Web Server 4 InitiatorAlias=spyalley.nsa.gov InitiatorAlias=Exchange Server If an initiator has been configured with a human-readable name or description, it may be communicated to the target during a Login Request PDU. If not, the host name can be used instead. This string is not used as an identifier, but can be displayed by the target's user interface in a list of initiators to which it is con- nected. This key SHOULD be sent by an initiator within the Login phase, if available. 11.8 TargetAddress Use: ALL, Declarative Senders: Target Scope: SW TargetAddress=domainname[:port][,portal-group-tag] If the TCP port is not specified, it is assumed to be the IANA- assigned default port for iSCSI. If the TargetAddress is returned as the result of a redirect status in a login response, the comma and portal group tag are omitted. If the TargetAddress is returned within a SendTargets response, the portal group tag is required. Examples: TargetAddress=10.0.0.1:5003,1 Julian Satran Expires August 2002 188 11iSCSI.book Page 189 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 TargetAddress=[1080:0:0:0:8:800:200C:417A],65 TargetAddress=[1080::8:800:200C:417A]:5003,1 TargetAddress=computingcenter.acme.com,23 The TargetAddress key is further described in Appendix D. - SendTar- gets Operation -. 11.9 InitialR2T Use: LO Senders: Initiator and Target Scope: SW InitialR2T= Examples: I->InitialR2T=No T->InitialR2T=No Default is Yes. Result function is OR. The InitialR2T key is used to turn off the default use of R2T, thus allowing an initiator to start sending data to a target as if it has received an initial R2T with Buffer Offset=0 and Desired Data Transfer Length=min (FirstBurstSize, Expected Data Transfer Length). The default action is that R2T is required, unless both the initiator and the target send this key-pair attribute specifying InitialR2T=No. Only the first outgoing data burst (immediate data and/or separate PDUs) can be sent unsolicited (i.e., not requiring an explicit R2T). 11.10 BidiInitialR2T Use: LO Senders: Initiator and Target Scope: SW BidiInitialR2T= Examples: I->BidiInitialR2T=No T->BidiInitialR2T=No Julian Satran Expires August 2002 189 11iSCSI.book Page 190 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Default is Yes. Result function is OR. The BidiInitialR2T key is used to turn off the default use of BiDiR2T, thus allowing an initiator to send data to a target without the target having sent an R2T to the initiator for the output data (write part) of a Bidirectional command (having both the R and the W bits set). The default action is that R2T is required, unless both the initiator and the target send this key-pair attribute specifying BidiInitialR2T=No. Only the first outgoing data burst (immediate data and/or separate PDUs) can be sent unsolicited by an R2T. 11.11 ImmediateData Use: LO Senders: Initiator and Target Scope: SW ImmediateData= Default is Yes. Result function is AND. The initiator and target negotiate support for immediate data. To turn immediate data off, the initiator or target must state its desire to do so. ImmediateData can be turned on if both the initiator and tar- get have ImmediateData=Yes. If ImmediateData is set to Yes and InitialR2T is set to Yes (default), then only immediate data are accepted in the first burst. If ImmediateData is set to No and InitialR2T is set to Yes, then the initiator MUST NOT send unsolicited data and the target MUST reject them with the corresponding response code. If ImmediateData is set to No and InitialR2T is set to No, then the initiator MUST NOT send unsolicited immediate data, but MAY send one unsolicited burst of Data-OUT PDUs. If ImmediateData is set to Yes and InitialR2T is set to No, then the initiator MAY send unsolicited immediate data and/or one unsolicited burst of Data-OUT PDUs. Julian Satran Expires August 2002 190 11iSCSI.book Page 191 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The following table is a summary of unsolicited data options: +----------+-------------+---------------------------------------+ |InitialR2T|ImmediateData| Result (up to FirstBurstSize) | +----------+-------------+---------------------------------------+ | No | No | Unsolicited data in data PDUs only. | +----------+-------------+---------------------------------------+ | No | Yes | Immediate & separate unsolicited data.| +----------+-------------+---------------------------------------+ | Yes | No | Unsolicited data disallowed. | +----------+-------------+---------------------------------------+ | Yes | Yes | Immediate unsolicited data only. | +----------+-------------+---------------------------------------+ 11.12 MaxRecvPDULength Use: ALL Senders: Initiator and Target Scope: CO MaxRecvPDULength= Default is 8192 bytes. This is a connection specific parameter. The initiator or target declares the maximum data segment length in bytes they can receive in an iSCSI PDU. For a target the value limiting the size of the receive PDUs is the lower of the declared MaxRecvPDULength and the negotiated MaxBurst- Size for solicited data or FirstBurstSize for unsolicited data. 11.13 MaxBurstSize Use: LO Senders: Initiator and Target Scope: SW MaxBurstSize= Default is 262144 (256 Kbytes). Julian Satran Expires August 2002 191 11iSCSI.book Page 192 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The initiator and target negotiate maximum SCSI data payload in bytes in an Data-In or a solicited Data-Out iSCSI sequence. A sequence of Data-In or Data-Out PDUs ending with a Data-In or Data-Out PDU with the F bit set to one. The minimum of the two numbers is selected. 11.14 FirstBurstSize Use: LO Senders: Initiator and Target Scope: SW FirstBurstSize= Default is 65536 (64 Kbytes). The initiator and target negotiate the maximum amount in bytes of unsolicited data an iSCSI initiator may send to the target, during the execution of a single SCSI command. This covers the immediate data (if any) and the sequence of unsolicited Data-Out PDUs (if any) that fol- low the command. The minimum of the two numbers is selected. FirstBurstSize MUST NOT exceed MaxBurstSize. 11.15 DefaultTime2Wait Use: LO Senders: Initiator and Target Scope: SW DefaultTime2Wait= Default is 3. The initiator and target negotiate the minimum time, in seconds, to wait before attempting an explicit/implicit logout or active task reassignment after an unexpected connection termination or a connec- tion reset. The higher of the two values is selected. Julian Satran Expires August 2002 192 11iSCSI.book Page 193 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 A value of 0 indicates that logout or active task reassignment can be attempted immediately. 11.16 DefaultTime2Retain Use: LO Senders: Initiator and Target Scope: SW DefaultTime2Retain= Default is 3. The initiator and target negotiate the maximum time, in seconds after an initial wait (Time2Wait), before which an explicit/implicit con- nection Logout or active task reassignment is still possible after an unexpected connection termination or a connection reset. This value is also the session state timeout if the connection in question is the last LOGGED_IN connection in the session. The lesser of the two values is selected. A value of 0 indicates that connection/task state is immediately dis- carded by the target. 11.17 MaxOutstandingR2T Use: LO Senders: Initiator and Target Scope: SW MaxOutstandingR2T= Default is 1. Initiator and target negotiate the maximum number of outstanding R2Ts per task, excluding any implied initial R2T that might be part of that task. An R2T is considered outstanding until the last data PDU (with the F bit set to 1) is transferred, or a sequence reception timeout (section 6.12.1) is encountered for that data sequence. Julian Satran Expires August 2002 193 11iSCSI.book Page 194 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 11.18 DataPDUInOrder Use: LO Senders: Initiator and Target Scope: SW DataPDUInOrder= Default is Yes. Result function is OR. No is used by iSCSI to indicate that the data PDUs within sequences can be in any order. Yes is used to indicate that data PDUs within sequences have to be at continuously increasing addresses and over- lays are forbidden. 11.19 DataSequenceInOrder Use: LO Senders: Initiator and Target Scope: SW DataSequenceInOrder= Default is Yes. Result function is OR. A Data Sequence is a sequence of Data-In or Data-Out PDUs ending with a Data-In or Data-Out PDU with the F bit set to one. A Data-out sequence is sent either unsolicited or in response to an R2T. Sequences cover an offset-range. If DataSequenceInOrder is set to No, Data PDU sequences may be trans- ferred in any order. If DataSequenceInOrder is set to Yes, Data Sequences MUST be trans- ferred using continuously non-decreasing sequence offsets (R2T buffer offset for writes, or the smallest SCSI Data-In buffer offset within a read data sequence). If ErrorRecoveryLevel is not 0 and if DataSequenceInOrder is set to Yes, a target may retry at most the last R2T, and an initiator may at most request retransmission for the last read data sequence. MaxOustandingR2T MUST be set to 1 in this case. Julian Satran Expires August 2002 194 11iSCSI.book Page 195 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 11.20 ErrorRecoveryLevel Use: LO Senders: Initiator and Target Scope: SW ErrorRecoveryLevel=<0 to 2> Default is 0. The initiator and target negotiate the recovery level supported. The minimum of the two values is selected. Recovery levels represent a combination of recovery capabilities. Each recovery level includes all the capabilities of the lower recov- ery levels and adds some new ones to them. In the description of recovery mechanisms, certain recovery classes are specified. Section 6.13 Error Recovery Hierarchy describes the mapping between the classes and the levels. 11.21 SessionType Use: LO, Declarative Senders: Initiator Scope: SW SessionType= Default is Normal. The Initiator indicates the type of session it wants to create. The target can either accept it or reject it. A discovery session indicates to the Target that the only purpose of this Session is discovery. The only requests a target accepts in this type of session are a text request with a SendTargets key and a logout request with reason "close the session". The discovery session implies MaxConnections = 1 and overrides both the default and an explicit setting. Julian Satran Expires August 2002 195 11iSCSI.book Page 196 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 11.22 The Vendor Specific Key Format Use: ALL Senders: Initiator and Target Scope: specific key dependent X-reversed.vendor.dns_name.do_something= Keys with this format are used for vendor-specific purposes. These keys always start with X-. To identify the vendor, we suggest you use the reversed DNS-name as a prefix to the key-proper. Julian Satran Expires August 2002 196 11iSCSI.book Page 196 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 12. IANA Considerations The temporary (user) well-known port number for iSCSI connections assigned by IANA is 3260. Julian Satran Expires August 2002 196 11iSCSI.book Page 198 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 References and Bibliography [AC] A Detailed Proposal for Access Control, Jim Hafner, T10/99- 245 [AESCBC] Frankel, S., Kelly, S., Glenn, R., "The AES Cipher Algorithm and Its Use with IPsec", Internet draft (work in progress), draft-ietf-ipsec-ciph-aes-cbc-03.txt, November 2001. [AESCTR] Walker, J., Moskowitz, R., "The AES128 CTR Mode of Operation and Its Use with IPsec", Internet draft (work in progress), draft-moskowitz-aes128-ctr-00.txt, September 2001. [BOOT] P. Sarkar & team draft-ietf-ips-iscsi-boot-01.txt [CAM] ANSI X3.232-199X, Common Access Method-3. [Castagnoli93] G. Castagnoli, S. Braeuer and M. Herrman "Optimi- zation of Cyclic Redundancy-Check Codes with 24 and 32 Parity Bits", IEEE Transact. on Communications, Vol. 41, No. 6, June 1993. [COBS] S. Cheshire and M. Baker, Consistent Overhead Byte Stuff- ing, IEEE Transactions on Networking, April 1999. [CRC] ISO 3309, High-Level Data Link Control (CRC 32). [NDT] M. Bakke & team, draft-ietf-ips-iscsi-name-disc-03.txt [RFC790] J. Postel, ASSIGNED NUMBERS, September 1981. [RFC791] INTERNET PROTOCOL, DARPA INTERNET PROGRAM PROTOCOL SPECIFICATION, September 1981. [RFC793] TRANSMISSION CONTROL PROTOCOL, DARPA INTERNET PROGRAM PROTOCOL SPECIFICATION, September 1981. [RFC1035] P. Mockapetris, DOMAIN NAMES - IMPLEMENTATION AND SPECIFICATION, November 1987. [RFC1122] Requirements for Internet Hosts-Communication Layer RFC1122, R. Braden (editor). [RFC1510] J. Kohl, C. Neuman, "The Kerberos Network Authentica- tion Service (V5)", September 1993. [RFC1766] H. Alvestrand, "Tags for the Identification of Lan- guages", March 1995. [RFC1964] J. Linn, "The Kerberos Version 5 GSS-API Mechanism", June 1996. [RFC1982] Elz, R., Bush, R., "Serial Number Arithmetic", RFC 1982, August 1996. [RFC1994] "W. Simpson, PPP Challenge Handshake Authentication Protocol (CHAP)", RFC 1994, August 1996. [RFC2025] C. Adams, "The Simple Public-Key GSS-API Mechanism (SPKM)", October 1996. [RFC2026] Bradner, S., "The Internet Standards Process -- Revi- sion 3", RFC 2026, October 1996. [RFC2044] Yergeau, F., "UTF-8, a Transformation Format of Uni- code and ISO 10646", October 1996. [RFC2045] N. Borenstein, N. Freed, "MIME (Multipurpose Internet Mail Extensions) Part One: Mechanisms for Specifying and Julian Satran Expires August 2002 198 11iSCSI.book Page 199 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Describing the Format of Internet Message Bodies", November 1996. [RFC2119] Bradner, S. "Key Words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC2234] D. Crocker, P. Overell Augmented BNF for Syntax Spec- ifications: ABNF. [RFC2246] T. Dierks, C. Allen, " The TLS Protocol Version 1.0. [RFC2373] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 2373, July 1998. [RFC2434] T. Narten, and H. Avestrand, "Guidelines for Writing an IANA Considerations Section in RFCs.", RFC2434, October 1998. [RFC2401] S. Kent, R. Atkinson, "Security Architecture for the Internet Protocol", RFC 2401, November 1998. [RFC2404] C. Madson, R. Glenn, "The Use of HMAC-SHA-1-96 within ESP and AH", RFC 2404, November 1998. [RFC2406] S. Kent, R. Atkinson, "IP Encapsulating Security Payload (ESP)", RFC 2406, November 1998. [RFC2407] D. Piper, "The Internet IP Security Domain of Interpre- tation of ISAKMP", RFC 2407, November 1998. [RFC2409] D. Harkins, D. Carrel, "The Internet Key Exchange (IKE)", RFC 2409, November 1998. [RFC2451] R. Pereira, R. Adams " The ESP CBC-Mode Cipher Algo- rithms". [RFC2732] R. Hinden, B. Carpenter, L. Masinter, "Format for Lit- eral IPv6 Addresses in URL's", RFC 2732, December 1999. [RFC2945], Wu, T., "The SRP Authentication and Key Exchange System", September 2000. [SAM] ANSI X3.270-1998, SCSI-3 Architecture Model (SAM). [SAM2] T10/1157D, SCSI Architecture Model - 2 (SAM-2). [SBC] NCITS.306-1998, SCSI-3 Block Commands (SBC). [Schneier] B. Schneier, "Applied Cryptography: Protocols, Algo- rithms, and Source Code in C", 2nd edition, John Wiley & Sons, New York, NY, 1996. [SPC] NCITS.351:200, SCSI-3 Primary Commands (SPC). [SEQ-EXT] Kent, S., "IP Encapsulating Security Payload (ESP)", Internet draft (work in progress), draft-ietf-ipsec-esp-v3- 01.txt, November 2002. [SEC-IPS] B. Aboba & team "Securing Block Storage Protocols over IP", Internet draft (work in progress), draft-ietf-ips-secu- rity-09.txt, February 2002. [SPC3]T10/1416-D, SCSI-3 Primary Commands (SPC). Authors' Addresses Julian Satran Julian Satran Expires August 2002 199 11iSCSI.book Page 200 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 IBM, Haifa Research Lab MATAM - Advanced Technology Center Haifa 31905, Israel Phone +972.4.829.6264 E-mail: Julian_Satran@vnet.ibm.com Kalman Meth IBM, Haifa Research Lab MATAM - Advanced Technology Center Haifa 31905, Israel Phone +972.4.829.6341 E-mail: meth@il.ibm.com Ofer Biran IBM, Haifa Research Lab MATAM - Advanced Technology Center Haifa 31905, Israel Phone +972.4.829.6253 E-mail: biran@il.ibm.com Daniel F. Smith IBM Almaden Research Center 650 Harry Road San Jose, CA 95120-6099, USA Phone: +1.408.927.2072 E-mail: dfsmith@almaden.ibm.com Jim Hafner IBM Almaden Research Center 650 Harry Road San Jose, CA 95120 Phone: +1.408.927.1892 E-mail: hafner@almaden.ibm.com Costa Sapuntzakis Cisco Systems, Inc. 170 W. Tasman Drive San Jose, CA 95134, USA Phone: +1.408.525.5497 E-mail: csapuntz@cisco.com Mark Bakke Cisco Systems, Inc. 6450 Wedgwood Road Maple Grove, MN USA 55311 Phone: +1.763.398.1000 E-Mail: mbakke@cisco.com Randy Haagens Julian Satran Expires August 2002 200 11iSCSI.book Page 201 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Hewlett-Packard Company 8000 Foothills Blvd. Roseville, CA 95747-5668, USA Phone: +1.916.785.4578 E-mail: Randy_Haagens@hp.com Matt Wakeley (current address) Sierra Logic, Inc. Phone: +1.916.772.1234 ext 116 E-mail: matt_wakeley@sierralogic.com Efri Zeidner SANgate Systems, Inc. 41 Hameyasdim Street P.O.B. 1486 Even-Yehuda, Israel 40500 Phone: +972.9.891.9555 E-mail: efri@sangate.com Paul von Stamwitz (current address) TrueSAN Networks, Inc. Phone: +1.408.869.4219 E-mail: pvonstamwitz@truesan.com Luciano Dalle Ore Quantum Corp. Phone: +1.408.232.6524 E-mail: ldalleore@snapserver.com Mallikarjun Chadalapaka Hewlett-Packard Company 8000 Foothills Blvd. Roseville, CA 95747-5668, USA Phone: +1.916.785.5621 E-mail: cbm@rose.hp.com Comments may be sent to Julian Satran Julian Satran Expires August 2002 201 11iSCSI.book Page 202 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Appendix A. Sync and Steering with Fixed Interval Markers This appendix presents a simple scheme for synchronization (PDU boundary retrieval). It uses markers that include synchronization information placed at fixed intervals in the TCP stream. A Marker consists of: Byte / 0 | 1 | 2 | 3 | / | | | | |7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0|7 6 5 4 3 2 1 0| +---------------+---------------+---------------+---------------+ 0| Next-iSCSI-PDU-start pointer - copy #1 | +---------------+---------------+---------------+---------------+ 4| Next-iSCSI-PDU-start pointer - copy #2 | +---------------+---------------+---------------+---------------+ The Marker schemes uses payload byte stream counting that includes every byte placed by iSCSI in the TCP stream except for the markers themselves. It also excludes any bytes that TCP counts but are not originated by iSCSI. The Marker indicates the offset to the next iSCSI PDU header. The Marker is eight bytes in length and contains two 32-bit offset fields that indicate how many bytes to skip in the TCP stream in order to find the next iSCSI PDU header. The marker uses two copies of the pointer so that a marker that spans a TCP packet boundary should leave at least one valid copy in one of the packets. The inserted value is independent of the marker interval. The use of markers is negotiable. The initiator and target MAY indi- cate their readiness to receive and/or send markers during login sep- arately for each connection. The default is No. A.1 Markers At Fixed Intervals A marker is inserted at fixed intervals in the TCP byte stream. During login, each end of the iSCSI session specifies the interval at which it is willing to receive the marker, or it disables the marker alto- gether. If a receiver indicates that it desires a marker, the sender MAY agree (during negotiation) and provide the marker at the desired interval. However, in certain environments, a sender not providing Julian Satran Expires August 2002 202 11iSCSI.book Page 203 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 markers to a receiver wanting markers may suffer an appreciable per- formance degradation. The marker interval and the initial marker-less interval are counted in terms of the bytes placed in the TCP stream data by iSCSI. When reduced to iSCSI terms, markers MUST indicate the offset to a 4- byte word boundary in the stream. The last two bits of each marker word are reserved and are considered 0 for offset computation. Padding iSCSI PDU payloads to 4-byte word boundaries simplifies marker manipulation. A.2 Initial Marker-less Interval To enable the connection setup including the login phase negotiation, marking (if any) is started only at the first marker interval after the end of the login phase. However, in order to enable the marker inclusion and exclusion mechanism to work without knowledge of the length of the login phase, the first marker will be placed in the TCP stream as if the Marker-less interval had included markers. Thus all markers appear in the stream at locations conforming to the formula: [(MI + 8) * n - 8] where MI = Marker Interval, n = integer number. As an example if the marker interval is 512 and the login ended at byte 1003 (first iSCSI placed byte is 0) the first marker will be inserted after byte 1031 in the stream. A.3 Negotiation The following operational key=value pairs are used to negotiate the fixed interval markers. The direction (output or input) is relative to the initiator. A.3.1 OFMarker, IFMarker Use: IO Senders: Initiator and Target Scope: CO OFMarker= IFMarker= Julian Satran Expires August 2002 203 11iSCSI.book Page 204 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Default is No. Result function is AND. OFMarker is used to turn on or off the initiator to target markers on the connection. IFMarker is used to turn on or off the target to ini- tiator markers on the connection. Examples: I->OFMarker=Yes,IFMarker=Yes T->OFMarker=Yes,IFMarker=Yes Results in the Marker being used in both directions while I->OFMarker=Yes,IFMarker=Yes T->OFMarker=Yes,IFMarker=No Results in Marker being used from the initiator to the target, but not from the target to initiator. A.3.2 OFMarkInt, IFMarkInt Use: IO Senders: Initiator and Target Scope: CO Offering: OFMarkInt=[,] IFMarkInt=[,] Responding: OFMarkInt=|Reject IFMarkInt=|Reject OFMarkInt is used to set the interval for the initiator to target markers on the connection. IFMarkInt is used to set the interval for the target to initiator markers on the connection. For the offering the initiator or target indicates the minimum to max- imum interval (in 4-byte words) it wants the markers for one or both Julian Satran Expires August 2002 204 11iSCSI.book Page 205 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 directions. In case it only wants a specific value, only a single value has to be specified. The responder selects a value within the minimum and maximum offered or the only value offered or indicates through the xFMarker key=value its inability to set and/or receive markers. When the interval is unacceptable the responder answers with "Reject". Reject is resetting the marker function in the specified direction (Output or Input) to No. The interval is measured from the end of a marker to the beginning of the next marker. For example, a value of 1024 means 1024 words (4096 bytes of iSCSI payload between markers). The default is 2048. Julian Satran Expires August 2002 205 11iSCSI.book Page 206 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Appendix B. Examples B.4 Read Operation Example +------------------+-----------------------+----------------------+ |Initiator Function| PDU Type | Target Function | +------------------+-----------------------+----------------------+ | Command request |SCSI Command (READ)>>> | | | (read) | | | +------------------+-----------------------+----------------------+ | | | Prepare Data Transfer| +------------------+-----------------------+----------------------+ | Receive Data | <<< SCSI Data-in | Send Data | +------------------+-----------------------+----------------------+ | Receive Data | <<< SCSI Data-in | Send Data | +------------------+-----------------------+----------------------+ | Receive Data | <<< SCSI Data-in | Send Data | +------------------+-----------------------+----------------------+ | | <<< SCSI Response |Send Status and Sense | +------------------+-----------------------+----------------------+ | Command Complete | | | +------------------+-----------------------+----------------------+ B.5 Write Operation Example +------------------+-----------------------+---------------------+ |Initiator Function| PDU Type | Target Function | +------------------+-----------------------+---------------------+ | Command request |SCSI Command (WRITE)>>>| Receive command | | (write) | | and queue it | +------------------+-----------------------+---------------------+ | | | Process old commands| +------------------+-----------------------+---------------------+ | | | Ready to process | | | <<< R2T | WRITE command | +------------------+-----------------------+---------------------+ | Send Data | SCSI Data-out >>> | Receive Data | +------------------+-----------------------+---------------------+ | | <<< R2T | Ready for data | +------------------+-----------------------+---------------------+ | | <<< R2T | Ready for data | +------------------+-----------------------+---------------------+ | Send Data | SCSI Data-out >>> | Receive Data | Julian Satran Expires August 2002 206 11iSCSI.book Page 207 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +------------------+-----------------------+---------------------+ | Send Data | SCSI Data-out >>> | Receive Data | +------------------+-----------------------+---------------------+ | | <<< SCSI Response |Send Status and Sense| +------------------+-----------------------+---------------------+ | Command Complete | | | +------------------+-----------------------+---------------------+ B.6 R2TSN/DataSN use Examples Output (write) data DataSN/R2TSN Example +------------------+-----------------------+----------------------+ |Initiator Function| PDU Type & Content | Target Function | +------------------+-----------------------+----------------------+ | Command request |SCSI Command (WRITE)>>>| Receive command | | (write) | | and queue it | +------------------+-----------------------+----------------------+ | | | Process old commands | +------------------+-----------------------+----------------------+ | | <<< R2T | Ready for data | | | R2TSN = 0 | | +------------------+-----------------------+----------------------+ | | <<< R2T | Ready for more data | | | R2TSN = 1 | | +------------------+-----------------------+----------------------+ | Send Data | SCSI Data-out >>> | Receive Data | | for R2TSN 0 | DataSN = 0, F=0 | | +------------------+-----------------------+----------------------+ | Send Data | SCSI Data-out >>> | Receive Data | | for R2TSN 0 | DataSN = 1, F=1 | | +------------------+-----------------------+----------------------+ | Send Data | SCSI Data >>> | Receive Data | | for R2TSN 1 | DataSN = 0, F=1 | | +------------------+-----------------------+----------------------+ | | <<< SCSI Response |Send Status and Sense | | | ExpDataSN = 0 | | +------------------+-----------------------+----------------------+ | Command Complete | | | +------------------+-----------------------+----------------------+ Julian Satran Expires August 2002 207 11iSCSI.book Page 208 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Input (read) data DataSN Example +------------------+-----------------------+----------------------+ |Initiator Function| PDU Type | Target Function | +------------------+-----------------------+----------------------+ | Command request |SCSI Command (READ)>>> | | | (read) | | | +------------------+-----------------------+----------------------+ | | | Prepare Data Transfer| +------------------+-----------------------+----------------------+ | Receive Data | <<< SCSI Data-in | Send Data | | | DataSN = 0, F=0 | | +------------------+-----------------------+----------------------+ | Receive Data | <<< SCSI Data-in | Send Data | | | DataSN = 1, F=0 | | +------------------+-----------------------+----------------------+ | Receive Data | <<< SCSI Data-in | Send Data | | | DataSN = 2, F=1 | | +------------------+-----------------------+----------------------+ | | <<< SCSI Response |Send Status and Sense | | | ExpDataSN = 3 | | +------------------+-----------------------+----------------------+ | Command Complete | | | +------------------+-----------------------+----------------------+ Bidirectional DataSN Example +------------------+-----------------------+----------------------+ |Initiator Function| PDU Type | Target Function | +------------------+-----------------------+----------------------+ | Command request |SCSI Command >>> | | | (Read-Write) | Read-Write | | +------------------+-----------------------+----------------------+ | | | Process old commands | +------------------+-----------------------+----------------------+ | | <<< R2T | Ready to process | | | R2TSN = 0 | WRITE command | +------------------+-----------------------+----------------------+ | * Receive Data | <<< SCSI Data-in | Send Data | | | DataSN = 0, F=0 | | +------------------+-----------------------+----------------------+ | * Receive Data | <<< SCSI Data-in | Send Data | Julian Satran Expires August 2002 208 11iSCSI.book Page 209 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 | | DataSN = 1, F=1 | | +------------------+-----------------------+----------------------+ | * Send Data | SCSI Data-out >>> | Receive Data | | for R2TSN 0 | DataSN = 0, F=1 | | +------------------+-----------------------+----------------------+ | | <<< SCSI Response |Send Status and Sense | | | ExpDataSN = 2 | | +------------------+-----------------------+----------------------+ | Command Complete | | | +------------------+-----------------------+----------------------+ *) Send data and Receive Data may be transferred simultaneously as in an atomic Read-Old-Write-New or sequential as in an atomic Read- Update-Write (in the alter case the R2T may follow the received data). Unsolicited and immediate output (write) data with DataSN Example +------------------+-----------------------+----------------------+ |Initiator Function| PDU Type & Content | Target Function | +------------------+-----------------------+----------------------+ | Command request |SCSI Command (WRITE)>>>| Receive command | | (write) |F=0 | and data | |+ immediate data | | and queue it | +------------------+-----------------------+----------------------+ | Send Unsolicited | SCSI Write Data >>> | Receive more Data | | Data | DataSN = 0, F=1 | | +------------------+-----------------------+----------------------+ | | | Process old commands | +------------------+-----------------------+----------------------+ | | <<< R2T | Ready for more data | | | R2TSN = 0 | | +------------------+-----------------------+----------------------+ | Send Data | SCSI Write Data >>> | Receive Data | | for R2TSN 0 | DataSN = 0, F=1 | | +------------------+-----------------------+----------------------+ | | <<< SCSI Response |Send Status and Sense | | | | | +------------------+-----------------------+----------------------+ | Command Complete | | | +------------------+-----------------------+----------------------+ Julian Satran Expires August 2002 209 11iSCSI.book Page 210 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 B.7 CRC Examples N.B. all Values are Hexadecimal 32 bytes of zeroes: Byte: 0 1 2 3 0: 00 00 00 00 ... 28: 00 00 00 00 CRC: aa 36 91 8a 32 bytes of ones: Byte: 0 1 2 3 0: ff ff ff ff ... 28: ff ff ff ff CRC: 43 ab a8 62 32 bytes of incrementing 00..1f: Byte: 0 1 2 3 0: 00 01 02 03 ... 28: 1c 1d 1e 1f CRC: 4e 79 dd 46 32 bytes of decrementing 1f..00: Byte: 0 1 2 3 0: 1f 1e 1d 1c ... 28: 03 02 01 00 CRC: 5c db 3f 11 Julian Satran Expires August 2002 210 11iSCSI.book Page 213 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Appendix C. Login Phase Examples In the first example, the initiator and target authenticate each other via Kerberos: I-> Login (CSG,NSG=0,1 T=1) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=KRB5,SRP,None T-> Login (CSG,NSG=0,0 T=0) AuthMethod=KRB5 I-> Login (CSG,NSG=0,1 T=1) KRB_AP_REQ= (krb_ap_req contains the Kerberos V5 ticket and authenticator with MUTUAL-REQUIRED set in the ap-options field) If the authentication is successful, the target proceeds with: T-> Login (CSG,NSG=0,1 T=1) KRB_AP_REP= (krb_ap_rep is the Kerberos V5 mutual authentication reply) If the authentication is successful, the initiator may proceed with: I-> Login (CSG,NSG=1,0 T=0) FirstBurstSize=0 T-> Login (CSG,NSG=1,0 T=0) FirstBurstSize=8192 MaxBurst- Size=8192 I-> Login (CSG,NSG=1,0 T=0) MaxBurstSize=8192 ... more iSCSI Operational Parameters T-> Login (CSG,NSG=1,0 T=0) ... more iSCSI Operational Parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" If the initiator‚ÇÖs authentication by the target is not success- ful, the target responds with: Julian Satran Expires August 2002 213 11iSCSI.book Page 214 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 T-> Login "login reject" instead of the Login KRB_AP_REP message, and terminates the con- nection. If the target‚ÇÖs authentication by the initiator is not success- ful, the initiator terminates the connection (without respond- ing to the Login KRB_AP_REP message). In the next example only the initiator is authenticated by the target via Kerberos: I-> Login (CSG,NSG=0,1 T=1) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=SRP,KRB5,None T-> Login-PR (CSG,NSG=0,0 T=0) AuthMethod=KRB5 I-> Login (CSG,NSG=0,1 T=1) KRB_AP_REQ=krb_ap_req (MUTUAL-REQUIRED not set in the ap-options field of krb_ap_req) If the authentication is successful, the target proceeds with: T-> Login (CSG,NSG=0,1 T=1) I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters . . . T-> Login (CSG,NSG=1,3 T=1)"login accept" In the next example, the initiator and target authenticate each other via SPKM1: I-> Login (CSG,NSG=0,1 T=1) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=SPKM1,KRB5,None T-> Login (CSG,NSG=0,0 T=0) Julian Satran Expires August 2002 214 11iSCSI.book Page 215 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 AuthMethod=SPKM1 I-> Login (CSG,NSG=0,0 T=0) SPKM_REQ= (spkm-req is the SPKM-REQ token with the mutual-state bit in the options field of the REQ-TOKEN set) T-> Login (CSG,NSG=0,0 T=0) SPKM_REP_TI= If the authentication is successful, the initiator proceeds: I-> Login (CSG,NSG=0,1 T=1) SPKM_REP_IT= If the authentication is successful, the target proceeds with: T-> Login (CSG,NSG=0,1 T=1) The initiator may proceed: I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" If the target‚ÇÖs authentication by the initiator is not success- ful, the initiator terminates the connection (without respond- ing to the Login SPKM_REP_TI message). If the initiator‚ÇÖs authentication by the target is not success- ful, the target responds with: T-> Login "login reject" instead of the Login "proceed and change stage" message, and terminates the connection. In the next example, the initiator and target authenticate each other via SPKM2: Julian Satran Expires August 2002 215 11iSCSI.book Page 216 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 I-> Login (CSG,NSG=0,0 T=0) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=SPKM1,SPKM2 T-> Login-PR (CSG,NSG=0,0 T=0) AuthMethod=SPKM2 I-> Login (CSG,NSG=0,1 T=1) SPKM_REQ= (spkm-req is the SPKM-REQ token with the mutual-state bit in the options field of the REQ-TOKEN not set) If the authentication is successful, the target proceeds with: T-> Login (CSG,NSG=0,1 T=1) The initiator may proceed: I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" In the next example, the initiator and target authenticate each other via SRP: I-> Login (CSG,NSG=0,1 T=1) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=KRB5,SRP,None T-> Login-PR (CSG,NSG=0,0 T=0) AuthMethod=SRP I-> Login (CSG,NSG=0,0 T=0) SRP_U= TargetAuth=Yes Julian Satran Expires August 2002 216 11iSCSI.book Page 217 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 T-> Login (CSG,NSG=0,0 T=0) SRP_N= SRP_g= SRP_s= I-> Login (CSG,NSG=0,0 T=0) SRP_A= T-> Login (CSG,NSG=0,0 T=0) SRP_B= I-> Login (CSG,NSG=0,1 T=1) SRP_M= If the initiator authentication is successful, the target pro- ceeds: T-> Login (CSG,NSG=0,1 T=1) SRP_HM= Where N, g, s, A, B, M, and H(A | M | K) are defined in [RFC2945]. If the target authentication is not successful, the initiator terminates the connection; otherwise, it proceeds. I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" If the initiator authentication is not successful, the target responds with: T-> Login "login reject" Instead of the T-> Login SRP_HM= message and ter- minates the connection. In the next example, only the initiator is authenticated by the target via SRP: Julian Satran Expires August 2002 217 11iSCSI.book Page 218 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 I-> Login (CSG,NSG=0,1 T=1) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=KRB5,SRP,None T-> Login-PR (CSG,NSG=0,0 T=0) AuthMethod=SRP I-> Login (CSG,NSG=0,0 T=0) SRP_U= TargetAuth=No T-> Login (CSG,NSG=0,0 T=0) SRP_N= SRP_g= SRP_s= I-> Login (CSG,NSG=0,0 T=0) SRP_A= T-> Login (CSG,NSG=0,0 T=0) SRP_B= I-> Login (CSG,NSG=0,1 T=1) SRP_M= If the initiator authentication is successful, the target pro- ceeds: T-> Login (CSG,NSG=0,1 T=1) I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" In the next example the initiator and target authenticate each other via CHAP: I-> Login (CSG,NSG=0,0 T=0) Julian Satran Expires August 2002 218 11iSCSI.book Page 219 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=KRB5,CHAP,None T-> Login-PR (CSG,NSG=0,0 T=0) AuthMethod=CHAP I-> Login (CSG,NSG=0,0 T=0) CHAP_A= T-> Login (CSG,NSG=0,0 T=0) CHAP_A= CHAP_I= CHAP_C= I-> Login (CSG,NSG=0,1 T=1) CHAP_N= CHAP_R= CHAP_I= CHAP_C= If the initiator authentication is successful, the target pro- ceeds: T-> Login (CSG,NSG=0,1 T=1) CHAP_N= CHAP_R= If the target authentication is not successful, the initiator aborts the connection; otherwise, it proceeds. I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" If the initiator authentication is not successful, the target responds with: T-> Login "login reject" Julian Satran Expires August 2002 219 11iSCSI.book Page 220 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Instead of the Login CHAP_R= "proceed and change stage" message and terminates the connection. In the next example, only the initiator is authenticated by the target via CHAP: I-> Login (CSG,NSG=0,1 T=0) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod=KRB5,CHAP,None T-> Login-PR (CSG,NSG=0,0 T=0) AuthMethod=CHAP I-> Login (CSG,NSG=0,0 T=0) CHAP_A= T-> Login (CSG,NSG=0,0 T=0) CHAP_A= CHAP_I= CHAP_C= I-> Login (CSG,NSG=0,1 T=1) CHAP_N= CHAP_R= If the initiator authentication is successful, the target pro- ceeds: T-> Login (CSG,NSG=0,1 T=1) I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" Julian Satran Expires August 2002 220 11iSCSI.book Page 221 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 In the next example, the initiator does not offer any security param- eters. It therefore, may offer iSCSI parameters on the Login PDU with the T bit set to 1, and the target may respond with a final Login Response PDU immediately: I-> Login (CSG,NSG=1,3 T=1) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 ... iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" ... ISCSI parameters In the next example, the initiator does offer security parame- ters on the Login PDU, but the target does not choose any (i.e., chooses the "None" values): I-> Login (CSG,NSG=0,1 T=1) InitiatorName=iqn.1999-07.com.os.hostid.77 TargetName=iqn.1999-07.com.acme.diskarray.sn.88 AuthMethod:KRB5,SRP,None T-> Login-PR (CSG,NSG=0,1 T=1) AuthMethod=None I-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters T-> Login (CSG,NSG=1,0 T=0) ... iSCSI parameters And at the end: I-> Login (CSG,NSG=1,3 T=1) optional iSCSI parameters T-> Login (CSG,NSG=1,3 T=1) "login accept" Julian Satran Expires August 2002 221 11iSCSI.book Page 222 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Appendix D. SendTargets Operation To reduce the amount of configuration required on an initiator, iSCSI provides the SendTargets text request. This initiator sends this com- mand to request a list of targets to which it may have access, as well as the list of addresses (IP address and TCP port) on which these tar- gets may be accessed. To make use of SendTargets, an initiator must first establish one of two types of sessions. If the initiator establishes the session using the key "SessionType=Discovery", the session is a discovery session, and a target name does not need to be specified. Otherwise, the ses- sion is a normal, operational session. The SendTargets command MUST only be sent during the full feature phase of a normal or discovery session. A system that contains targets MUST support discovery sessions on each of its IP addresses, and MUST support the SendTargets command on the discovery session. A target MUST support the SendTargets command on operational sessions; these will only return address information about the target to which the session is connected, and do not return information about other targets. An initiator MAY make use of the SendTargets as it sees fit. A SendTargets command consists of a single Text request PDU. This PDU contains exactly one text key and value. The text key MUST be SendTargets. The expected response depends upon the value, as well as whether the session is a discovery or operational session. The value must be one of: all The initiator is requesting that information on all relevant targets known to the implementation be returned. This value MUST be supported on a discovery session, and MUST NOT be sup- ported on an operational session. If an iSCSI target name is specified, the session should respond with addresses for only the named target, if possible. This value MUST be supported on discovery sessions. A discovery Julian Satran Expires August 2002 222 11iSCSI.book Page 223 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 session MUST be capable of returning addresses for those tar- gets that would have been returned had value=all been desig- nated. The session should respond only with addresses for the target to which the session is logged in. This MUST be supported on operational sessions, and MUST NOT return targets other than the one to which the session is logged in. The response to this command is a text response that contains a list of zero or more targets and, optionally, their addresses. Each target is returned as a target record. A target record begins with the Tar- getName text key, followed by a list of TargetAddress text keys, and bounded by the end of the text response or the next TargetName key, which begins a new record. No text keys other than TargetName and TargetAddress are permitted within a SendTargets response. For the format of the TargetName, see Section 11.4 TargetName. A discovery session MAY respond to a SendTargets request with its com- plete list of targets, or with a list of targets that is based on the name of the initiator logged in to the session. A SendTargets response MUST NOT not contain target names if there are no targets for the requesting initiator to access. Each target record returned includes zero or more TargetAddress fields. A SendTargets response MUST NOT contain iSCSI default target names. Each target record starts with one text key of the form: TargetName= Followed by zero or more address keys of the form: TargetAddress=[:], The hostname-or-ipaddress and tcp port are as specified in the Sec- tion 2.2.6 Naming and Addressing. Julian Satran Expires August 2002 223 11iSCSI.book Page 224 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Each TargetAddress belongs to a portal group, identified by its numeric, decimal portal group tag. The iSCSI target name, together with this tag, constitutes the SCSI port identifier; the tag need be unique only within a given target name's list of addresses. Multiple-connection sessions can span iSCSI addresses that belong to the same portal group. Multiple-connection sessions cannot span iSCSI addresses that belong to different portal groups. If a SendTargets response reports an iSCSI address for a target, it SHOULD also report all other addresses in its portal group in the same response. A SendTargets text response can be longer than a single Text Response PDU, and makes use of the long text responses as specified. After obtaining a list of targets from the discovery target session, an iSCSI initiator may initiate new sessions to log in to the discov- ered targets for full operation. The initiator MAY keep the session to a default target open, and MAY send subsequently SendTargets com- mands to discover new targets. Examples: This example is the SendTargets response from a single target that has no other interface ports. Initiator sends text request that contains: SendTargets=all Target sends a text response that contains: TargetName=iqn.1993-11.com.acme.diskarray.sn.8675309 All the target had to return in the simple case was the target name. It is assumed by the initiator that the IP address and TCP port for this target are the same as used on the current connection to the default iSCSI target. Julian Satran Expires August 2002 224 11iSCSI.book Page 225 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 The next example has two internal iSCSI targets, each accessible via two different ports with different IP addresses. The following is the text response: TargetName=iqn.1993-11.com.acme.diskarray.sn.8675309 TargetAddress=10.1.0.45:3000,1 TargetAddress=10.1.1.45:3000,2 TargetName=iqn.1993-11.com.acme.diskarray.sn.1234567 TargetAddress=10.1.0.45:3000,1 TargetAddress=10.1.1.45:3000,2 Both targets share both addresses; the multiple addresses are likely used to provide multi-path support. The initiator may connect to either target name on either address. Each of the addresses has its own portal group tag; they do not support spanning multiple-connec- tion sessions with each other. Keep in mind also that the portal group tags for the two named targets are independent of one another; portal group "1" on the first target is not necessarily the same as portal group "1" on the second. In the above example, a DNS host name could have been returned instead of an IP address, and that an IPv6 addresses (5 to 16 dotted-decimal numbers) could have also been returned. The next text response shows a target that supports spanning sessions across multiple addresses, which indicates the use of the portal group tags: TargetName=iqn.1993-11.com.acme.diskarray.sn.8675309 TargetAddress=10.1.0.45:3000,1 TargetAddress=10.1.1.46:3000,1 TargetAddress=10.1.0.47:3000,2 TargetAddress=10.1.1.48:3000,2 TargetAddress=10.1.1.49:3000,3 In this example, any of the target addresses can be used to reach the same target. A single-connection session can be established to any of these TCP addresses. A multiple-connection session could span addresses .45 and .46 or .47 and .48, but cannot span any other combi- nation. A TargetAddress with its own tag (.49), cannot be combined with any other address within the same session. This SendTargets response does not indicate whether .49 supports mul- tiple connections per session; it communicated via the MaxConnections text key upon login to the target. Julian Satran Expires August 2002 225 11iSCSI.book Page 226 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Appendix E. Algorithmic Presentation of Error Recovery Classes This appendix illustrates the error recovery classes using a pseudo- programming-language. The procedure names are chosen to be obvious to most implementers. Each of the recovery classes described has initia- tor procedures as well as target procedures. These algorithms focus on outlining the mechanics of error recovery classes, and ignore all other aspects/cases. Examples of this approach are: - Handling for only certain Opcode types is shown. - Only certain reason codes (for example, Recovery in Logout command) are outlined. - Resultant cases, such as recovery of Synchronization on a header digest error are considered out-of-scope in these algo- rithms. In this particular example a header digest error may lead to connection recovery if some type of sync and steering layer is not implemented. These algorithms strive to convey the iSCSI error recovery concepts in the simplest terms, and are not designed to be optimal. E.8 General Data Structure and Procedure Description This section defines the procedures and data structures that are com- monly used by all the error recovery algorithms. The structures may not be the exhaustive representations of what is required for a typi- cal implementation. Data structure definitions - struct TransferContext { int TargetTransferTag; int ExpectedDataSN; }; struct TCB { /* task control block */ Boolean SoFarInOrder; int ExpectedDataSN; /* used for both R2Ts, and Data */ int MissingDataSNList[MaxMissingDPDU]; Boolean FbitReceived; Boolean StatusXferd; Boolean CurrentlyAllegiant; int ActiveR2Ts; Julian Satran Expires August 2002 226 11iSCSI.book Page 227 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 int Response; char *Reason; struct TransferContext TransferContextList[MaxOutStandingR2T]; int InitiatorTaskTag; int CmdSN; }; struct Connection { struct Session SessionReference; Boolean SoFarInOrder; int CID; int State; int ExpectedStatSN; int MissingStatSNList[MaxMissingSPDU]; Boolean PerformConnectionCleanup; }; struct Session { int NumConnections; int CmdSN; int Maxconnections; int ErrorRecoveryLevel; struct iSCSIEndpoint OtherEndInfo; struct Connection ConnectionList[MaxSupportedConns]; }; Procedure descriptions - Receive-a-In-PDU(transport connection, inbound PDU); check-basic-validity(inbound PDU); Start-Timer(timeout handler, argument, timeout value); Build-And-Send-Reject(transport connection, bad PDU, reason code); E.9 Within-command Error Recovery Algorithms E.9.1 Procedure Descriptions Recover-Data-if-Possible(last required DataSN, task control block); Build-And-Send-DSnack(task control block); Build-And-Send-Abort(task control block); SCSI-Task-Completion(task control block); Build-And-Send-a-Data-Burst(transport connection, R2T PDU, task control block); Build-And-Send-R2T(transport connection, description of data, Julian Satran Expires August 2002 227 11iSCSI.book Page 228 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 task control block); Build-And-Send-Status(transport connection, task control block); Transfer-Context-Timeout-Handler(transfer context); Implementation-specific tunables - InitiatorDataSNACKEnabled, TargetDataSNACKSupported, TargetRecoveryR2TEnabled. Notes: - Some procedures used in this section, including: Recover-Sta- tus-if-Possible, Handle-Status-SNACK-request, Evaluate-a- StatSN are defined in Within-connection recovery algorithms. - The Response processing pseudo-code, shown in the target algo- rithms, applies to all solicited PDUs that carry StatSN - SCSI Response, Text Response etc. E.9.2 Initiator Algorithms Recover-Data-if-Possible(LastRequiredDataSN, TCB) { if (InitiatorDataSNACKEnabled) { if (# of missing PDUs is trackable) { Note the missing DataSNs in TCB. Build-And-Send-DSnack(TCB); } else { TCB.Reason = "Protocol service CRC error"; } } else { TCB.Reason = "Protocol service CRC error"; } if (TCB.Reason = "Protocol service CRC error") { Clear the missing PDU list in the TCB. if (TCB.StatusXferd is not TRUE) Build-And-Send-Abort(TCB); } } Receive-a-In-PDU(Connection, CurrentPDU) { check-basic-validity(CurrentPDU); if (Header-Digest-Bad) discard, return; Retrieve TCB for CurrentPDU.InitiatorTaskTag. Julian Satran Expires August 2002 228 11iSCSI.book Page 229 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 if ((CurrentPDU.type = Data) or (CurrentPDU.type = R2T)) { if (Data-Digest-Bad) { send-data-SNACK = TRUE; LastRequiredDataSN = CurrentPDU.DataSN; } else { if (TCB.SoFarInOrder = TRUE) { if (current DataSN is expected) { Increment TCB.ExpectedDataSN. } else { TCB.SoFarInOrder = FALSE; send-data-SNACK = TRUE; } } else { if (current DataSN was considered missing) { remove current DataSN from missing PDU list. } else if (current DataSN is higher than expected) { send-data-SNACK = TRUE; } else { discard, return; } Adjust TCB.ExpectedDataSN if appropriate. } LastRequiredDataSN = CurrentPDU.DataSN - 1; } if (send-data-SNACK is TRUE and task is not already considered failed) { Recover-Data-if-Possible(LastRequiredDataSN, TCB); } if (missing data PDU list is empty) { TCB.SoFarInOrder = TRUE; } if (CurrentPDU.type = R2T) { Increment ActiveR2Ts for this task. Build-And-Send-A-Data-Burst(Connection, CurrentPDU, TCB); } } else if (CurrentPDU.type = Response) { if (Data-Digest-Bad) { send-status-SNACK = TRUE; } else { TCB.StatusXferd = TRUE; Store the status information in TCB. if (ExpDataSN does not match) { Julian Satran Expires August 2002 229 11iSCSI.book Page 230 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 TCB.SoFarInOrder = FALSE; Recover-Data-if-Possible(current DataSN, TCB); } if (missing data PDU list is empty) { TCB.SoFarInOrder = TRUE; } send-status-SNACK = Evaluate-a-StatSN(Connection, CurrentPDU.StatSN); } if (send-status-SNACK is TRUE) Recover-Status-if-Possible(Connection, CurrentPDU); } else { /* REST UNRELATED TO WITHIN-COMMAND-RECOVERY, NOT SHOWN */ } if ((TCB.SoFarInOrder is TRUE) and (TCB.StatusXferd is TRUE)) { SCSI-Task-Completion(TCB); } } E.9.3 Target Algorithms Receive-a-In-PDU(Connection, CurrentPDU) { check-basic-validity(CurrentPDU); if (Header-Digest-Bad) discard, return; Retrieve TCB for CurrentPDU.InitiatorTaskTag. if (CurrentPDU.type = Data) { Retrieve TContext from CurrentPDU.TargetTransferTag; if (Data-Digest-Bad) { Build-And-Send-Reject(Connection, CurrentPDU, Payload-Digest-Error); Note the missing data PDUs in MissingDataRange[]. send-recovery-R2T = TRUE; } else { if (current DataSN is not expected) { Note the missing data PDUs in MissingDataRange[]. send-recovery-R2T = TRUE; } if (CurrentPDU.Fbit = TRUE) { if (current PDU is solicited) { Decrement TCB.ActiveR2Ts. } if ((current PDU is unsolicited and Julian Satran Expires August 2002 230 11iSCSI.book Page 231 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 data received is less than I/O size and data received is less than FirstBurstSize) or {current PDU is solicited and the size of this burst is less than expected)) { send-recovery-R2T = TRUE; Note the missing data in MissingDataRange[]. } } } Increment TContext.ExpectedDataSN. if (send-recovery-R2T is TRUE and task is not already considered failed) { if (TargetRecoveryR2TEnabled is TRUE) { Increment TCB.ActiveR2Ts. Build-And-Send-R2T(Connection, MissingDataRange, TCB); } else { if (current PDU is the last unsolicited) TCB.Reason = "Not enough unsolicited data"; else TCB.Reason = "Protocol service CRC error"; } } if (TCB.ActiveR2Ts = 0) { Build-And-Send-Status(Connection, TCB); } } else if (CurrentPDU.type = SNACK) { snack-failure = FALSE; if (this is data retransmission request) { if (TargetDataSNACKSupported) { if (the request is satisfiable) { Build-And-Send-A-Data-Burst(CurrentPDU, TCB); } else { snack-failure = TRUE; } } else { snack-failure = TRUE; } if (snack-failure is TRUE) { Build-And-Send-Reject(Connection, CurrentPDU, Data-SNACK-Reject); if (TCB.StatusXferd is not TRUE) { TCB.Reason = "SNACK Rejected"; Build-And-Send-Status(Connection, TCB); Julian Satran Expires August 2002 231 11iSCSI.book Page 232 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 } } } else { Handle-Status-SNACK-request(Connection, CurrentPDU); } } else { /* REST UNRELATED TO WITHIN-COMMAND-RECOVERY, NOT SHOWN */ } } Transfer-Context-Timeout-Handler(TContext) { Retrieve TCB and Connection from TContext. Decrement TCB.ActiveR2Ts. if (TargetRecoveryR2TEnabled is TRUE and task is not already considered failed) { Note the missing data PDUs in MissingDataRange[]. Build-And-Send-R2T(Connection, MissingDataRange, TCB); } else { TCB.Reason = "Protocol service CRC error"; if (TCB.ActiveR2Ts = 0) { Build-And-Send-Status(Connection, TCB); } } } E.10 Within-connection Recovery Algorithms E.10.1 Procedure Descriptions Procedure descriptions: Recover-Status-if-Possible(transport connection, currently received PDU); Evaluate-a-StatSN(transport connection, current StatSN); Retransmit-Command-if-Possible(transport connection, CmdSN); Build-And-Send-SSnack(transport connection); Build-And-Send-Command(transport connection, task control block); Command-Acknowledge-Timeout-Handler(task control block); Status-Expect-Timeout-Handler(transport connection); Build-And-Send-Nop-Out(transport connection); Handle-Status-SNACK-request(transport connection, status SNACK PDU); Retransmit-Status-Burst(status SNACK, task control block); Is-Acknowledged(beginning StatSN, run size); Implementation-specific tunables: Julian Satran Expires August 2002 232 11iSCSI.book Page 233 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 InitiatorCommandRetryEnabled, InitiatorStatusExpectNopEnabled, Initi- atorProactiveSNACKEnabled, InitiatorStatusSNACKEnabled, TargetSta- tusSNACKSupported. Notes: - The initiator algorithms only deal with unsolicited Nop-In PDUs for generating status SNACKs. Solicited Nop-In PDU has an assigned StatSN, which, when out-of-order, could trigger the out-of-order StatSN handling in Within-command algo- rithms, again leading to Recover-Status-if-Possible. - The pseudo-code shown may result in the retransmission of unacknowledged commands in more cases than necessary. This will not however affect the correctness of the operation since the target is required to discard the duplicate CmdSNs. - The procedure Build-And-Send-Async is defined in the Connec- tion recovery algorithms. - The procedure Status-Expect-Timeout-Handler describes how initiators may proactively attempt to retrieve the Status if they so choose. This procedure is assumed to be triggered much before the standard ULP timeout. E.10.1.1 Initiator Algorithms Recover-Status-if-Possible(Connection, CurrentPDU) { if ((Connection.state = LOGGED_IN) and connection is not already considered failed) { if (InitiatorStatusSNACKEnabled) { if (# of missing PDUs is trackable) { Note the missing StatSNs in Connection; Build-And-Send-SSnack(Connection); } else { Connection.PerformConnectionCleanup = TRUE; } } else { Connection.PerformConnectionCleanup = TRUE; } if (Connection.PerformConnectionCleanup is TRUE) { Start-Timer(Connection-Cleanup-Handler, Connection, 0); } } } Julian Satran Expires August 2002 233 11iSCSI.book Page 234 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Retransmit-Command-if-Possible(Connection, CmdSN) { if (InitiatorCommandRetryEnabled) { Retrieve the InitiatorTaskTag, and thus TCB for the CmdSN. Build-And-Send-Command(Connection, TCB); } } Evaluate-a-StatSN(Connection, StatSN) { send-status-SNACK = FALSE; if (Connection.SoFarInOrder is TRUE) { if (current StatSN is the expected) { Increment Connection.ExpectedStatSN. } else { Connection.SoFarInOrder = FALSE; send-status-SNACK = TRUE; } } else { if (current StatSN was considered missing) { remove current StatSN from the missing list. } else { if (current StatSN is higher than expected){ send-status-SNACK = TRUE; } else { discard, return; } } Adjust Connection.ExpectedStatSN if appropriate. if (missing StatSN list is empty) { Connection.SoFarInOrder = TRUE; } } return send-status-SNACK; } Receive-a-In-PDU(Connection, CurrentPDU) { check-basic-validity(CurrentPDU); if (Header-Digest-Bad) discard, return; Retrieve TCB for CurrentPDU.InitiatorTaskTag. if (CurrentPDU.type = Nop-In) { if (the PDU is unsolicited) { Julian Satran Expires August 2002 234 11iSCSI.book Page 235 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 if (current StatSN is not expected) { Recover-Status-if-Possible(Connection, CurrentPDU); } if (current ExpCmdSN is not Session.CmdSN) { Retransmit-Command-if-Possible(Connection, CurrentPDU.ExpCmdSN); } } } else if (CurrentPDU.type = Reject) { if (it is a data digest error on immediate data) { Retransmit-Command-if-Possible(Connection, CurrentPDU.BadPDUHeader.CmdSN); } } else if (CurrentPDU.type = Response) { send-status-SNACK = Evaluate-a-StatSN(Connection, CurrentPDU.StatSN); if (send-status-SNACK is TRUE) Recover-Status-if-Possible(Connection, CurrentPDU); } else { /* REST UNRELATED TO WITHIN-CONNECTION-RECOVERY, * NOT SHOWN */ } } Command-Acknowledge-Timeout-Handler(TCB) { Retrieve the Connection for TCB. Retransmit-Command-if-Possible(Connection, TCB.CmdSN); } Status-Expect-Timeout-Handler(Connection) { if (InitiatorStatusExpectNopEnabled) { Build-And-Send-Nop-Out(Connection); } else if (InitiatorProactiveSNACKEnabled){ if ((Connection.state = LOGGED_IN) and connection is not already considered failed) { Build-And-Send-SSnack(Connection); } } } E.10.1.2 Target Algorithms Julian Satran Expires August 2002 235 11iSCSI.book Page 236 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Handle-Status-SNACK-request(Connection, CurrentPDU) { if (TargetStatusSNACKSupported) { if (request for an acknowledged run) { Build-And-Send-Reject(Connection, CurrentPDU, Protocol-Error); } else if (request for an untransmitted run) { discard, return; } else { Retransmit-Status-Burst(CurrentPDU, TCB); } } else { Build-And-Send-Async(Connection, DroppedConnection, DefaultTime2Wait, DefaultTime2Retain); } } E.10.2 Connection Recovery Algorithms E.10.2.1 Procedure Descriptions Build-And-Send-Async(transport connection, reason code, minimum time, maximum time); Pick-A-Logged-In-Connection(session); Build-And-Send-Logout(transport connection, logout connection identifier, reason code); PerformImplicitLogout(transport connection, logout connection identifier, target information); PerformLogin(transport connection, target information); CreateNewTransportConnection(target information); Build-And-Send-Command(transport connection, task control block); Connection-Cleanup-Handler(transport connection); Connection-Resource-Timeout-Handler(transport connection); Quiesce-And-Prepare-for-New-Allegiance(session, task control block); Build-And-Send-Logout-Response(transport connection, CID of connection in recovery, reason code); Build-And-Send-TaskMgmt-Response(transport connection, task mgmt command PDU, response code); Establish-New-Allegiance(task control block, transport connection); Schedule-Command-To-Continue(task control block); Notes: - Transport exception conditions, such as unexpected connection termination, connection reset, and hung connection while the Julian Satran Expires August 2002 236 11iSCSI.book Page 237 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 connection is in the full-feature phase, are all assumed to be asynchronously signaled to the iSCSI layer using the Transport_Exception_Handler procedure. E.10.2.2 Initiator Algorithms Receive-a-In-PDU(Connection, CurrentPDU) { check-basic-validity(CurrentPDU); if (Header-Digest-Bad) discard, return; Retrieve TCB from CurrentPDU.InitiatorTaskTag. if (CurrentPDU.type = Async) { if (CurrentPDU.AsyncEvent = ConnectionDropped) { Retrieve the AffectedConnection for CurrentPDU.Parameter1. AffectedConnection.State = CLEANUP_WAIT; } else if (CurrentPDU.AsyncEvent = LogoutRequest)) { Retrieve the AffectedConnection for CurrentPDU.Parameter1. AffectedConnection.State = LOGOUT_REQUESTED; AffectedConnection.PerformConnectionCleanup = TRUE; Start-Timer(Connection-Cleanup-Handler, AffectedConnection, CurrentPDU.Parameter2); } else if (CurrentPDU.AsyncEvent = SessionDropped)) { for (each Connection) { Connection.state = CLEANUP_WAIT; } Session.state = FAILED; Start-Timer(Session-Continuation-Handler, Session, CurrentPDU.Parameter2); } } else if (CurrentPDU.type = LogoutResponse) { Retrieve the CleanupConnection for CurrentPDU.CID. if (CurrentPDU.Response = failure) { CleanupConnection.State = CLEANUP_WAIT; } else { CleanupConnection.State = FREE; } } else if (CurrentPDU.type = LoginResponse) { if (this is a response to an implicit Logout) { Retrieve the CleanupConnection. if (successful) { CleanupConnection.State = FREE; Connection.State = LOGGED_IN; Julian Satran Expires August 2002 237 11iSCSI.book Page 238 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 } else { CleanupConnection.State = CLEANUP_WAIT; DestroyTransportConnection(Connection); } } } else { /* REST UNRELATED TO CONNECTION-RECOVERY, * NOT SHOWN */ } if (CleanupConnection.State = FREE) { for (each command that was active on CleanupConnection) { /* Establish new connection allegiance */ NewConnection = Pick-A-Logged-In-Connection(Session); Build-And-Send-Command(NewConnection, TCB); } } } Connection-Cleanup-Handler(Connection) { Retrieve Session from Connection. Start-Timer(Connection-Resource-Timeout-Handler, Connection, DefaultTime2Retain); if (Connection can still exchange iSCSI PDUs) { NewConnection = Connection; } else { if (there are other logged-in connections) { NewConnection = Pick-A-Logged-In-Connection(Session); } else { NewConnection = CreateTransportConnection(Session.OtherEndInfo); Initiate an implicit Logout on NewConnection for Connection.CID. return; } } Build-And-Send-Logout(NewConnection, Connection.CID, RecoveryRemove); } Transport_Exception_Handler(Connection) { Connection.PerformConnectionCleanup = TRUE; if (the event is an unexpected transport disconnect) { Julian Satran Expires August 2002 238 11iSCSI.book Page 239 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Connection.State = CLEANUP_WAIT; Start-Timer(Connection-Cleanup-Handler, Connection, LogooutLoginMinTime); } else { Connection.State = FREE; } } E.10.2.3 Target Algorithms Receive-a-In-PDU(Connection, CurrentPDU) { check-basic-validity(CurrentPDU); if (Header-Digest-Bad) discard, return; else if (Data-Digest-Bad) { Build-And-Send-Reject(Connection, CurrentPDU, Payload-Digest-Error); discard, return; } Retrieve TCB and Session. if (CurrentPDU.type = Logout) { if (CurrentPDU.ReasonCode = RecoveryRemove) { Retrieve the CleanupConnection from CurrentPDU.CID). for (each command active on CleanupConnection) { Quiesce-And-Prepare-for-New-Allegiance(Session, TCB); TCB.CurrentlyAllegiant = FALSE; } Cleanup-Connection-State(CleanupConnection); if ((quiescing successful) and (cleanup successful)) { Build-And-Send-Logout-Response(Connection, CleanupConnection.CID, Success); } else { Build-And-Send-Logout-Response(Connection, CleanupConnection.CID, Failure); } } } else if (CurrentPDU.type = TaskManagement) { if (CurrentPDU.function = "TaskReassign") { if (Session.ErrorRecoveryLevel < 2) { Build-And-Send-TaskMgmt-Response(Connection, CurrentPDU, "Task failover not supported"); } else if (task is not found) { Julian Satran Expires August 2002 239 11iSCSI.book Page 240 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Build-And-Send-TaskMgmt-Response(Connection, CurrentPDU, "Task not in task set"); } else if (task is currently allegiant) { Build-And-Send-TaskMgmt-Response(Connection, CurrentPDU, "Task still allegiant"); } else { Establish-New-Allegiance(TCB, Connection); TCB.CurrentlyAllegiant = TRUE; Schedule-Command-To-Continue(TCB); } } } else { /* REST UNRELATED TO CONNECTION-RECOVERY, * NOT SHOWN */ } } Transport_Exception_Handler(Connection) { Connection.PerformConnectionCleanup = TRUE; if (the event is an unexpected transport disconnect) { Connection.State = CLEANUP_WAIT; Start-Timer(Connection-Resource-Timeout-Handler, Connection, (DefaultTime2Wait+DefaultTime2Retain)); if (this Session has full-feature phase connections left) { DifferentConnection = Pick-A-Logged-In-Connection(Session); Build-And-Send-Async(DifferentConnection, DroppedConnection, DefaultTime2Wait, DefaultTime2Retain); } } else { Connection.State = FREE; } } Julian Satran Expires August 2002 240 11iSCSI.book Page 241 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Appendix F. Clearing effects on various events on targets The following tables describes the target behavior on receiving the events specified in the rows of the table. The second table is merely an extension of the first table and defines clearing actions for more objects on the same events. The legend is: Y = Yes (cleared/discarded/reset on the event specified in the row). Unless noted otherwise, the clearing action is applica- ble only for the issuing initiator port. N = No (not affected on the event specified in the row, i.e. stays at previous value). NA = Not Applicable, or Not Defined. Julian Satran Expires August 2002 241 11iSCSI.book Page 242 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +-----+-----+-----+-----+-----+-----+-----+ |IT(1)|IC(2)|RR(3)|PR(4)|CT(5)|ST(6)|PP(7)| +---------------------+-----+-----+-----+-----+-----+-----+-----+ |connection failure(8)|Y |Y |N |N |N |N |Y | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |connection state |NA |NA |N |N |Y |N |NA | |timeout (9) | | | | | | | | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |session timeout/ |Y |Y |N |N |Y |Y |Y(14)| |closure/reinstatement| | | | | | | | |(10) | | | | | | | | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |session continuation |NA |NA |N |N |N(11)|N |NA | |(12) | | | | | | | | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |successful connection|Y |Y |N |N |Y |N |Y(13)| |close logout | | | | | | | | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |session failure (18) |Y |Y |N |N |N |N |Y | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |successful recovery |Y |Y |N |N |N |N |Y(13)| |Logout | | | | | | | | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |failed Logout |Y |Y |N |N |N |N |Y | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |connection Login |NA |NA |N |N |NA |Y(15)|NA | |(leading) | | | | | | | | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |connection Login |NA |NA |N |N |N(11)|N |Y | |(non-leading) | | | | | | | | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |target cold reset(16)|Y |Y |Y |Y(17)|Y |Y |Y | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |target warm reset(16)|Y |Y |Y |N |Y |Y |Y | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |LU reset(19) |Y |Y |Y |N |Y |Y |Y | +---------------------+-----+-----+-----+-----+-----+-----+-----+ |powercycle(16) |Y |Y |Y |Y(17)|Y |Y |Y | +---------------------+-----+-----+-----+-----+-----+-----+-----+ 1.Incomplete TTTs - Target Transfer Tags on which the target is still expecting PDUs to be received. Examples include TTTs received via R2T, NOP-IN etc. Julian Satran Expires August 2002 242 11iSCSI.book Page 243 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 2.Immediate Commands - immediate commands but waiting for execution on a target, for ex., Abort Task Set. 3.Regular Reservations - these are the SCSI reservations managed by the SCSI Reserve and Release commands. 4.Persistent Reservations - the objects that are covered in this col- umn are registration information, and the persistent reservation information. 5.Connection Tasks - tasks that are active on the iSCSI connection in question. 6.Session Tasks - tasks that are active on the entire iSCSI session, so is a union of ‚Çÿconnection tasks‚ÇÖ on all participating connections. 7.Partial PDUs (if any) - PDUs that are partially sent and waiting for transport window credit to complete the transmission. 8.Connection failure is a connection exception condition -one of transport connection shutdown, transport connection reset, or trans- port connection timeout abruptly terminating the iSCSI full-feature phase connection. A connection failure always takes the connection state machine to the CLEANUP_WAIT state. 9.Connection state timeout happens if a connection spends more time than agreed upon during Login negotiation in the CLEANUP_WAIT state, and this takes the connection to the FREE state (M1 transition in con- nection cleanup state diagram). 10.Session state timeout happens when the last connection state time- out happens and no tasks are waiting for reassignment. This takes the session to the FREE state (N6 transition in the session state dia- gram). Session closure and reinstatement are defined 11.This clearing effect is however "Y" only if it is a connection reinstatement and the operational ErrorRecoveryLevel is less than 2. 12.Session continuation is as defined in Section 4.3.6 Session Con- tinuation, closure and failure. Julian Satran Expires August 2002 243 11iSCSI.book Page 244 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 13.This clearing effect is valid only if the connection is being logged-out on a different connection and when the connection being logged out on the target may have some partial PDUs pending to be sent. In all other cases, the effect is "NA". 14.This clearing effect is valid only for a "close the session" logout in a multi-connection session. In all other cases, the effect is "NA". 15.Applicable only if this leading connection login is a session rein- statement. If that is not the case, this is "NA". 16.This operation affects all logged-in initiators. 17.Only if the SCSI APTPL bit (SPC-2) was not used in the registration (Note that iSCSI defines target cold reset as protocol-equivalent to a target powercycle). If APTPL was used, this is "N". 18.Session failure is as defined in Section 4.3.6 Session Continua- tion, closure and failure. 19.This operation affects all logged-in initiators and the clearing effects are only applicable to the LU being reset. Julian Satran Expires August 2002 244 11iSCSI.book Page 245 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 +-----+-----+-----+-----+-----+------+ |DC(1)|DD(2)|SS(3)|CS(4)|DS(5)|CRN(6)| +---------------------+-----+-----+-----+-----+-----+------+ |connection failure |N |Y |N |N |N |N | +---------------------+-----+-----+-----+-----+-----+------+ |connection state |Y |NA |Y |N |NA |N | |timeout | | | | | | | +---------------------+-----+-----+-----+-----+-----+------+ |session timeout/ |Y |Y |Y(7) |Y |NA |NA | |closure/reinstatement| | | | | | | +---------------------+-----+-----+-----+-----+-----+------+ |session continuation |N(11)|NA*12|NA |N |NA*13|N | +---------------------+-----+-----+-----+-----+-----+------+ |successful connection|Y |Y |Y |N |NA |N | |close Logout | | | | | | | +---------------------+-----+-----+-----+-----+-----+------+ |session failure |N |Y |N |N |N |N | +---------------------+-----+-----+-----+-----+-----+------+ |successful recovery |Y |Y |Y |N |N |N | |Logout | | | | | | | +---------------------+-----+-----+-----+-----+-----+------+ |failed Logout |N |Y(9) |N |N |N |N | +---------------------+-----+-----+-----+-----+-----+------+ |connection Login |NA |NA |N(8) |N(8) |NA |Y | |(leading | | | | | | | +---------------------+-----+-----+-----+-----+-----+------+ |connection Login |N(11)|NA*12|N(8) |N |NA*13|N | |(non-leading) | | | | | | | +---------------------+-----+-----+-----+-----+-----+------+ |target cold reset |Y |Y |Y |Y(10)|NA |Y | +---------------------+-----+-----+-----+-----+-----+------+ |target warm reset |Y |Y |N |N |NA |Y | +---------------------+-----+-----+-----+-----+-----+------+ |LU reset |N |Y |N |N |N |Y | +---------------------+-----+-----+-----+-----+-----+------+ |powercycle |Y |Y |Y |Y(10)|NA |Y | +---------------------+-----+-----+-----+-----+-----+------+ 1.Discontiguous Commands - commands allegiant to the connection in question and waiting to be reordered in the iSCSI layer. All ‚Ç£Y‚Ç¥s in this column assume that the task causing the event (if indeed the event is the result of a task) is issued as an immediate command, since the discontiguities can be ahead of the task. Julian Satran Expires August 2002 245 11iSCSI.book Page 246 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 2.Discontiguous Data - data PDUs received for the task in question and waiting to be reordered due to prior discontiguities in DataSN. 3.StatSN 4.CmdSN 5.DataSN 6.Command Reference Number - defined by SAM-2, and follows the reset rules defined by SAM-2. 7.It clears the StatSN on all the connections. 8.This sequence number is instantiated on this event. 9.A logout failure drives the connection state machine to the CLEANUP_WAIT state, similar to the connection failure event. Hence, it has a similar effect on this and several other protocol aspects. 10.This is cleared by virtue of the fact that all sessions with all initiators are terminated. 11.This clearing effect is "Y" if it is a connection reinstatement. 12.This clearing effect is "Y" only if it is a connection reinstate- ment and the operational ErrorRecoveryLevel is 2. 13.This clearing effect is "N" only if it is a connection reinstate- ment and the operational ErrorRecoveryLevel is 2. Julian Satran Expires August 2002 246 11iSCSI.book Page 244 Friday, March 1, 2002 11:25 AM iSCSI 1-March-02 Full Copyright Statement "Copyright (C) The Internet Society (date). All Rights Reserved. This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distrib- uted, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organiza- tions, except as needed for the purpose of developing Internet stan- dards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to trans- late it into languages other than English. The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns. This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANT- ABILITY OR FITNESS FOR A PARTICULAR PURPOSE." Julian Satran Expires August 2002 244