Network Working Group V. Narayanan Internet-Draft L. Dondeti Intended status: Standards Track Qualcomm, Inc. Expires: August 28, 2008 February 25, 2008 EAP Extensions for EAP Re-authentication Protocol (ERP) draft-ietf-hokey-erx-13 Status of this Memo By submitting this Internet-Draft, each author represents that any applicable patent or other IPR claims of which he or she is aware have been or will be disclosed, and any of which he or she becomes aware will be disclosed, in accordance with Section 6 of BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF), its areas, and its working groups. Note that other groups may also distribute working documents as Internet- Drafts. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." The list of current Internet-Drafts can be accessed at http://www.ietf.org/ietf/1id-abstracts.txt. The list of Internet-Draft Shadow Directories can be accessed at http://www.ietf.org/shadow.html. This Internet-Draft will expire on August 28, 2008. Copyright Notice Copyright (C) The IETF Trust (2008). Abstract The Extensible Authentication Protocol (EAP) is a generic framework supporting multiple types of authentication methods. In systems where EAP is used for authentication, it is desirable to not repeat the entire EAP exchange with another authenticator. This document specifies extensions to EAP and EAP keying hierarchy to support an EAP method-independent protocol for efficient re-authentication between the peer and an EAP re-authentication server through any authenticator. The re-authentication server may be in the home Narayanan & Dondeti Expires August 28, 2008 [Page 1] Internet-Draft ERP February 2008 network or in the local network that the peer is connecting to. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. ERP Description . . . . . . . . . . . . . . . . . . . . . . . 5 3.1. ERP With the Home ER Server . . . . . . . . . . . . . . . 5 3.2. ERP with a Local ER Server . . . . . . . . . . . . . . . . 8 4. ER Key Hierarchy . . . . . . . . . . . . . . . . . . . . . . . 10 4.1. rRK Derivation . . . . . . . . . . . . . . . . . . . . . . 11 4.2. rRK Properties . . . . . . . . . . . . . . . . . . . . . . 12 4.3. rIK Derivation . . . . . . . . . . . . . . . . . . . . . . 12 4.4. rIK Properties . . . . . . . . . . . . . . . . . . . . . . 13 4.5. rIK Usage . . . . . . . . . . . . . . . . . . . . . . . . 13 4.6. rMSK Derivation . . . . . . . . . . . . . . . . . . . . . 14 4.7. rMSK Properties . . . . . . . . . . . . . . . . . . . . . 15 5. Protocol Details . . . . . . . . . . . . . . . . . . . . . . . 15 5.1. ERP Bootstrapping . . . . . . . . . . . . . . . . . . . . 15 5.2. Steps in ERP . . . . . . . . . . . . . . . . . . . . . . . 18 5.2.1. Multiple Simultaneous Runs of ERP . . . . . . . . . . 20 5.2.2. ERP Failure Handling . . . . . . . . . . . . . . . . . 21 5.3. New EAP Packets . . . . . . . . . . . . . . . . . . . . . 22 5.3.1. EAP-Initiate/Re-auth-Start Packet . . . . . . . . . . 23 5.3.2. EAP-Initiate/Re-auth Packet . . . . . . . . . . . . . 24 5.3.3. EAP Finish/Re-auth Packet . . . . . . . . . . . . . . 26 5.3.4. TV and TLV Attributes . . . . . . . . . . . . . . . . 29 5.4. Replay Protection . . . . . . . . . . . . . . . . . . . . 30 5.5. Channel Binding . . . . . . . . . . . . . . . . . . . . . 30 6. Lower Layer Considerations . . . . . . . . . . . . . . . . . . 31 7. Transport of ERP Messages . . . . . . . . . . . . . . . . . . 32 8. Security Considerations . . . . . . . . . . . . . . . . . . . 32 9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 36 10. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 38 11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 39 11.1. Normative References . . . . . . . . . . . . . . . . . . . 39 11.2. Informative References . . . . . . . . . . . . . . . . . . 39 Appendix A. Example ERP Exchange . . . . . . . . . . . . . . . . 40 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 41 Intellectual Property and Copyright Statements . . . . . . . . . . 42 Narayanan & Dondeti Expires August 28, 2008 [Page 2] Internet-Draft ERP February 2008 1. Introduction The Extensible Authentication Protocol (EAP) is a an authentication framework which supports multiple authentication methods. The primary purpose is network access authentication, and a key- generating method is used when the lower layer wants to enforce access control. The EAP keying hierarchy defines two keys to be derived by all key generating EAP methods: the Master Session Key (MSK) and the Extended MSK (EMSK). In the most common deployment scenario, an EAP peer and an EAP server authenticate each other through a third party known as the EAP authenticator. The EAP authenticator or an entity controlled by the EAP authenticator enforces access control. After successful authentication, the EAP server transports the MSK to the EAP authenticator; the EAP authenticator and the EAP peer establish transient session keys (TSK) using the MSK as the authentication key, key derivation key or a key transport key, and use the TSK for per-packet access enforcement. When a peer moves from one authenticator to another, it is desirable to avoid a full EAP authentication to support fast handovers. The full EAP exchange with another run of the EAP method can take several round trips and significant time to complete, causing delays in handover times. Some EAP methods specify the use of state from the initial authentication to optimize re-authentications by reducing the computational overhead, but method-specific re-authentication takes at least 2 round trips with the original EAP server in most cases (e.g., [6]). It is also important to note that several methods do not offer support for re-authentication. Key sharing across authenticators is sometimes used as a practical solution to lower handover times. In that case, compromise of an authenticator results in compromise of keying material established via other authenticators. Other solutions for fast re-authentication exist in the literature [7] [8]. In conclusion, to achieve low latency handovers, there is a need for a method-independent re-authentication protocol that completes in less than 2 round trips, preferably with a local server. The EAP re- authentication problem statement is described in detail in [9]. This document specifies EAP Re-authentication Extensions (ERX) for efficient re-authentication using EAP. The protocol that uses these extensions itself is referred to as the EAP re-authentication Protocol (ERP). It supports EAP method independent re-authentication for a peer that has valid, unexpired key material from a previously performed EAP authentication. The protocol and the key hierarchy required for EAP re-authentication is described in this document. Narayanan & Dondeti Expires August 28, 2008 [Page 3] Internet-Draft ERP February 2008 2. Terminology The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [1]. This document uses the basic EAP terminology [2] and EMSK keying hierarchy terminology [3]. In addition, this document uses the following terms: ER peer - An EAP peer that supports the EAP re-authentication protocol. All references to "peer" in this document imply an ER peer, unless specifically noted otherwise. ER Authenticator - An entity that supports the authenticator functionality for EAP re-authentication described in this document. All references to "authenticator" in this document imply an ER authenticator, unless specifically noted otherwise. ER Server - An entity that performs the server portion of ERP described here. This entity may or may not be an EAP server. All references to "server" in this document imply an ER server, unless specifically noted otherwise. ER server is a logical entity; the home ER server is located on the same backend authentication server as the EAP server in the home domain. The local ER server may not necessarily be a full EAP server. ERX - EAP re-authentication extensions. ERP - EAP re-authentication Protocol that uses the re- authentication extensions. rRK - re-authentication root Key, derived from the EMSK or DSRK. rIK - re-authentication Integrity Key, derived from the rRK. rMSK - re-authentication MSK. This is a per-authenticator key, derived from the rRK. keyName-NAI - ERP messages are integrity protected with the rIK or the DS-rIK. The use of rIK or DS-rIK for integrity protection of ERP messages is indicated by the EMSKname [3], the protocol, which is ERP, and the realm, which indicates the domainname of the ER server. The EMSKname is copied into the username part of the NAI. Narayanan & Dondeti Expires August 28, 2008 [Page 4] Internet-Draft ERP February 2008 Domain - Refers to a "key management domain" as defined in [3]. For simplicity, it is referred to as "domain" in this document. The terms "home domain" and "local domain" are used to differentiate between the originating key management domain that performs the full EAP exchange with the peer and the local domain to which a peer may be attached to at a given time. 3. ERP Description ERP allows a peer and server to mutually verify proof of possession of keying material from an earlier EAP method run and establish a security association between the peer and the authenticator. The authenticator acts as a pass-through entity for the Re-authentication protocol in a manner similar to that of an EAP authenticator described in RFC 3748 [2]. ERP is a single round-trip exchange between the peer and the server; it is independent of the lower layer and the EAP method used during the full EAP exchange. The ER server may be in the home domain or in the same (visited) domain as the peer and the authenticator. Figure 2 shows the protocol exchange. The first time the peer attaches to any network, it performs a full EAP exchange (shown in Figure 1) with the EAP server; as a result an MSK is distributed to the EAP authenticator. The MSK is then used by the authenticator and the peer to establish TSKs as needed. At the time of the initial EAP exchange, the peer and the server also derive an EMSK, which is used to derive a re-authentication Root Key (rRK). More precisely, a re- authentication Root Key is derived from the EMSK or from a Domain Specific Root Key (DSRK), which itself is derived from the EMSK. The rRK is only available to the peer and the ER server and is never handed out to any other entity. Further, a re-authentication Integrity Key (rIK) is derived from the rRK; the peer and the ER server use the rIK to provide proof of possession while performing an ERP exchange. The rIK is also never handed out to any entity and is only available to the peer and server. When the ER server is in the home domain, the peer and the server use the rIK and rRK derived from the EMSK and when the ER server is not in the home domain, they use the DS-rIK and DS-rRK corresponding to the local domain. The domain of the ER server is identified by the realm portion of the keyname-NAI in ERP messages. 3.1. ERP With the Home ER Server Narayanan & Dondeti Expires August 28, 2008 [Page 5] Internet-Draft ERP February 2008 EAP Peer EAP Authenticator EAP Server ======== ================= ========== <--- EAP-Request/ ------ Identity ----- EAP Response/ ---> Identity ---AAA(EAP Response/Identity)--> <--- EAP Method -------> <------ AAA(EAP Method --------> exchange exchange) <----AAA(MSK, EAP-Success)------ <---EAP-Success--------- Figure 1: EAP Authentication Peer Authenticator Server ==== ============= ====== [<-- EAP Initiate/ ----- Re-auth-Start] [<-- EAP-Request/ ------ Identity] ---- EAP Initiate/ ----> ----AAA(EAP Initiate/ ----------> Re-auth/ Re-auth/ [Bootstrap] [Bootstrap]) <--- EAP Finish/ ------> <---AAA(rMSK,EAP Finish/--------- Re-auth/ Re-auth/ [Bootstrap] [Bootstrap]) Note: [] brackets indicate optionality. Figure 2: ERP Exchange Two new EAP codes, EAP-Initiate and EAP-Finish, are specified in this document for the purpose of EAP re-authentication. When the peer identifies a target authenticator that supports EAP re- authentication, it performs an ERP exchange, as shown in Figure 2; the exchange itself may happen when the peer attaches to a new Narayanan & Dondeti Expires August 28, 2008 [Page 6] Internet-Draft ERP February 2008 authenticator supporting EAP re-authentication, or prior to attachment. The peer initiates ERP by itself; it may also do so in response to an EAP-Initiate/Re-auth-Start message from the new authenticator. The EAP-Initiate/Re-auth-Start message allows the authenticator to trigger the ERP exchange. It is plausible that the authenticator does not know whether the peer supports ERP and whether the peer has performed a full EAP authentication through another authenticator. The authenticator MAY initiate the ERP exchange by sending the EAP-Initiate/Re-auth-Start message, and if there is no response, sends the EAP-Request/Identity message. Note that this avoids having two EAP messages in flight at the same time [2]. The authenticator may send the EAP-Initiate/ Re-auth-Start message and wait for a short, locally configured, amount of time. If the peer does not already know, this message indicates to the peer that the authenticator supports ERP. In response to this trigger from the authenticator, the peer can initiate the ERP exchange by sending an EAP-Initiate/Re-auth message. If there is no response from the peer after the necessary retransmissions (see Section 6), the authenticator MUST initiate EAP by sending EAP-Request message, typically EAP-Request/Identity message. Note that the authenticator may receive an EAP-Initiate/ Re-auth message after it has sent an EAP-Request/Identity message. If the authenticator supports ERP, it MUST proceed with the ERP exchange. When the EAP-Request/Identity times out, the authenticator MUST NOT close connection if an ERP exchange is in progress or has already succeeded in establishing a reauthentication MSK. If the authenticator does not support ERP, it drops EAP-Initiate/ Re-auth messages [2] as the EAP code of those packets is greater than 4. ERP capable peer will exhaust EAP-Initiate/Re-auth message retransmissions and fall back to EAP authentication by responding to EAP Request/Identity messages from the authenticator. If the peer does not support ERP or if it does not have unexpired key material from a previous EAP authentication, it drops EAP-Initiate/ Re-auth-Start messages. If there is no response to EAP-Initiate/ Re-auth-Start message, the authenticator SHALL send EAP Request (typically EAP Request/Identity) message to start EAP authentication. Note that this may introduce some delay in starting EAP. In some lower layers, the delay can be minimized or even avoided by the peer initiating EAP by sending messages such as EAPoL-Start in the IEEE 802.1X specification [10]. The peer sends an EAP-Initiate/Re-auth message that contains the keyName-NAI to identify the ER server's domain and the rIK used to protect the message, and a sequence number for replay protection. The EAP-Initiate/Re-auth message is integrity protected with the rIK. The authenticator uses the realm in the keyName-NAI [4] field to send Narayanan & Dondeti Expires August 28, 2008 [Page 7] Internet-Draft ERP February 2008 the message to the appropriate ER server. The server uses the keyName to lookup the rIK. The server, after verifying proof of possession of the rIK, and freshness of the message, derives a re- authentication MSK (rMSK) from the rRK using the sequence number as an input to the key derivation. The server updates the expected sequence number to the received sequence number plus one. In response to the EAP-Initiate/Re-auth message, the server sends an EAP-Finish/Re-auth message; this message is integrity protected with the rIK. The server transports the rMSK along with this message to the authenticator. The rMSK is transported in a manner similar to that of the MSK along with the EAP-Success message in a full EAP exchange. Ongoing work in [11] describes an additional key distribution protocol that can be used to transport the rRK from an EAP server to one of many different ER servers that share a trust relationship with the EAP server. The peer MAY request the server for the rMSK lifetime. If so, the ER server sends the rMSK lifetime in the EAP-Finish/Re-auth message. In an ERP bootstrap exchange, the peer MAY request the server for the rRK lifetime. If so, the ER server sends the rRK lifetime in the EAP-Finish/Re-auth message. The peer verifies the replay protection and the integrity of the message. It then uses the sequence number in the EAP-Finish/Re-auth message to compute the rMSK. The lower-layer security association protocol is ready to be triggered after this point. 3.2. ERP with a Local ER Server The defined ER extensions allow executing the ERP with an ER server in the local domain (access network). The local ER server may be co- located with a local AAA server. The peer may learn about the presence of a local ER server in the network and the local domain (or ER server) name either via the lower layer or by means of ERP bootstrapping. The peer uses the domain name and the EMSK to compute the DSRK and from that key, the DS-rRK; the peer also uses the domain name in the realm portion of the keyName-NAI for using ERP in the local domain. Figure 3 shows the full EAP and subsequent local ERP exchange Figure 4 with a local ER server. Narayanan & Dondeti Expires August 28, 2008 [Page 8] Internet-Draft ERP February 2008 Peer EAP Authenticator Local ER Server Home EAP Server ==== ================= =============== =============== <-- EAP-Request/ -- Identity -- EAP Response/--> Identity --AAA(EAP Response/--> Identity) --AAA(EAP Response/ --> Identity, [DSRK Request, domain name]) <------------------------ EAP Method exchange------------------> <---AAA(MSK, DSRK, ---- EMSKname, EAP-Success) <--- AAA(MSK, ----- EAP-Success) <---EAP-Success----- Figure 3: Local ERP Exchange, Initial EAP Exchange Peer ER Authenticator Local ER Server ==== ================ =============== [<-- EAP Initiate/ -------- Re-auth-Start] [<-- EAP-Request/ --------- Identity] ---- EAP Initiate/ -------> ----AAA(EAP-Initiate/ --------> Re-auth Re-auth) <--- EAP Finish/ ---------- <---AAA(rMSK,EAP Finish/------- Re-auth Re-auth) Narayanan & Dondeti Expires August 28, 2008 [Page 9] Internet-Draft ERP February 2008 Figure 4: Local ERP Exchange As shown in Figure 4, the local ER server may be present in the path of the full EAP exchange (e.g., this may be one of the AAA entities, such as AAA proxies, in the path between the authenticator and the home EAP server of the peer). In that case, the ER server requests the DSRK by sending the domain name to the EAP server. In response, the EAP server computes the DSRK by following the procedure specified in [3] and sends the DSRK and the key name, EMSKname, to the ER server in the claimed domain. The local domain is responsible for announcing that same domain name via the lower layer to the peer. If the peer does not know the domain name (did not receive the domain name via the lower layer announcement, due to a missed announcement or lack of support for domain name announcements in a specific lower layer), it SHOULD initiate ERP bootstrap exchange with the home ER server to obtain the domain name. The local ER server SHALL request the home AAA server for the DSRK by sending the domain name in the AAA message that carries the EAP-Initiate/Reauth bootstrap message. The local ER server MUST be in the path from the peer to the home ER server. If it is not, it cannot request the DSRK. After receiving the DSRK and the EMSKname, the local ER server computes the DS-rRK and the DS-rIK from the DSRK as defined in Section 4.1 and Section 4.3 below. After receiving the domain name, the peer also derives the DSRK, the DS-rRK and the DS-rIK. These keys are referred to by a keyName-NAI formed as follows: the username part of the NAI is the EMSKname, the realm portion of the NAI is the domain name. Both parties also maintain a sequence number (initialized to zero) corresponding to the specific keyName-NAI. Subsequently, when the peer attaches to an authenticator within the local domain, it may perform an ERP exchange with the local ER server to obtain an rMSK for the new authenticator. 4. ER Key Hierarchy Each time the peer re-authenticates to the network, the peer and the authenticator establish an rMSK. The rMSK serves the same purposes that an MSK, which is the result of full EAP authentication, serves. To prove possession of the rRK, we specify the derivation of another key, the rIK. These keys are derived from the rRK. Together they constitute the ER key hierarchy. The rRK is derived from either the EMSK or a DSRK as specified in Section 4.1. For the purpose of rRK derivation, this document specifies derivation of a Usage Specific Root Key (USRK) or a Domain Narayanan & Dondeti Expires August 28, 2008 [Page 10] Internet-Draft ERP February 2008 Specific USRK (DS-USRK) in accordance with [3] for re-authentication. The USRK designated for re-authentication is the re-authentication root key (rRK). A DS-USRK designated for re-authentication is the DS-rRK available to a local ER server in a particular domain. For simplicity, the keys are referred to without the DS label in the rest of the document. However, the scope of the various keys is limited to just the respective domains they are derived for, in the case of the domain specific keys. Based on the ER server with which the peer performs the ERP exchange, it knows the corresponding keys that must be used. The rRK is used to derive a rIK, and rMSKs for one or more authenticators. The figure below shows the key hierarchy with the rRK, rIK and rMSKs. rRK | +--------+--------+ | | | rIK rMSK1 ...rMSKn Figure 5: Re-authentication Key Hierarchy The derivations in this document are according to [3]. Key derivations, field encodings, where unspecified, default to that document. 4.1. rRK Derivation The rRK may be derived from the EMSK or DSRK. This section provides the relevant key derivations for that purpose. The rRK is derived as specified in [3]. rRK = KDF (K, S), where, K = EMSK or K = DSRK and S = rRK Label | "\0" | length The rRK Label is an IANA-assigned 8-bit ASCII string: EAP Re-authentication Root Key@ietf.org assigned from the "USRK key labels" name space in accordance with [3]. Narayanan & Dondeti Expires August 28, 2008 [Page 11] Internet-Draft ERP February 2008 The KDF and algorithm agility for the KDF is as defined in [3]. An rRK derived from the DSRK is referred to as a DS-rRK in the rest of the document. All the key derivation and properties specified in this section remain the same. 4.2. rRK Properties The rRK has the following properties. These properties apply to the rRK regardless of the parent key used to derive it. o The length of the rRK MUST be equal to the length of the parent key used to derive it. o The rRK is to be used only as a root key for re-authentication and never used to directly protect any data. o The rRK is only used for derivation of rIK and rMSK as specified in this document. o The rRK MUST remain on the peer and the server that derived it and MUST NOT be transported to any other entity. o The lifetime of the rRK is never greater than that of its parent key. The rRK is expired when the parent key expires and MUST be removed from use at that time. 4.3. rIK Derivation The re-authentication Integrity Key (rIK) is used for integrity protecting the ERP exchange. This serves as the proof of possession of valid keying material from a previous full EAP exchange by the peer to the server. The rIK is derived as follows. rIK = KDF (K, S ) where, K = rRK and S = rIK Label | "\0" | cryptosuite | length The rIK Label is the 8-bit ASCII string: Re-authentication Integrity Key@ietf.org The length field refers to the length of the rIK in octets encoded as specified in [3]. Narayanan & Dondeti Expires August 28, 2008 [Page 12] Internet-Draft ERP February 2008 The cryptosuite and length of the rIK are part of the input to the key derivation function to ensure cryptographic separation of keys if different rIKs of different lengths for use with different MAC algorithms are derived from the same rRK. The cryptosuite is encoded as an 8-bit number: See Section 5.3.2 for cryptosuite specification. The rIK is referred to by EMSKname-NAI within the context of ERP messages. The username part of EMSKname-NAI is the EMSKname; the realm is the domain name of the ER server. In case of ERP with the home ER server, the peer uses the realm from its original NAI; in case of a local ER server, the peer uses the domain name received at the lower layer or through a ERP bootstrapping exchange. An rIK derived from a DS-rRK is referred to as a DS-rIK in the rest of the document. All the key derivation and properties specified in this section remain the same. 4.4. rIK Properties The rIK has the following properties. o The length of the rIK MUST be equal to the length of the rRK. o The rIK is only used for authentication of the ERP exchange as specified in this document. o The rIK MUST NOT be used to derive any other keys. o The rIK must remain on the peer and the server and MUST NOT be transported to any other entity. o The rIK is cryptographically separate from any other keys derived from the rRK. o The lifetime of the rIK is never greater than that of its parent key. The rIK MUST be expired when the EMSK expires and MUST be removed from use at that time. 4.5. rIK Usage The rIK is the key whose possession is demonstrated by the peer and the ERP server to the other party. The peer demonstrates possession of the rIK by computing the integrity checksum over the EAP-Initiate/ Re-auth message. When the peer uses the rIK for the first time, it can choose the integrity algorithm to use with the rIK. The peer and the server MUST use the same integrity algorithm with a given rIK for all ERP messages protected with that key. The peer and the server store the algorithm information after the first use and the same Narayanan & Dondeti Expires August 28, 2008 [Page 13] Internet-Draft ERP February 2008 algorithm for all subsequent uses of that rIK. If the server's policy does not allow the use of the cryptosuite selected by the peer, the server SHALL reject the EAP-Initiate/ Re-auth message and SHOULD send a list of acceptable cryptosuites in the EAP-Finish/Re-auth message. The rIK length may be different from the key length required by an integrity algorithm. In case of hash-based MAC algorithms, the key is first hashed to the required key length as specified in [5]. In case of cipher-based MAC algorithms, if the required key length is less than 32 octets, the rIK is hashed using HMAC-SHA256 and the first k octets of the output are used where k is the key length required by the algorithm. If the required key length is more than 32 octets, the first k octets of the rIK are used by the cipher-based MAC algorithm. 4.6. rMSK Derivation The rMSK is derived at the peer and server and delivered to the authenticator. The rMSK is derived following an EAP Re-auth protocol exchange. The rMSK is derived as follows. rMSK = KDF (K, S ) where, K = rRK and S = rMSK label | "\0" | SEQ | length The rMSK label is the 8-bit ASCII string: Re-authentication Master Session Key@ietf.org The length field refers to the length of the rMSK in octets. The length field is encoded as specified in [3]. SEQ is the sequence number sent by the peer in the EAP-Initiate/ Re-auth message. This field is encoded as a 16-bit number in the network byte order (see Section 5.3.2). An rMSK derived from a DS-rRK is referred to as a DS-rIK in the rest of the document. All the key derivation and properties specified in this section remain the same. Narayanan & Dondeti Expires August 28, 2008 [Page 14] Internet-Draft ERP February 2008 4.7. rMSK Properties The rMSK has the following properties: o The length of the rMSK MUST be equal to the length of the rRK. o The rMSK is delivered to the authenticator and is used for the same purposes that an MSK is used at an authenticator. o The rMSK is cryptographically separate from any other keys derived from the rRK. o The lifetime of the rMSK is less than or equal to that of the rRK. It MUST NOT be greater than the lifetime of the rRK. o If a new rRK is derived, subsequent rMSKs MUST be derived from the new rRK. Previously delivered rMSKs MAY still be used until the expiry of the lifetime. o A given rMSK MUST NOT be shared by multiple authenticators. 5. Protocol Details 5.1. ERP Bootstrapping We identify two types of bootstrapping for ERP: explicit and implicit bootstrapping. In implicit bootstrapping, the local ER server SHOULD include its domain name and request the DSRK from the home AAA server during the initial EAP exchange, in the AAA message encapsulating the first EAP Response message sent by the peer. If the EAP exchange is successful, the server sends the DSRK for the local ER server (derived using the EMSK and the domain name as specified in [3]), EMSKname and DSRK lifetime along with the EAP-Success message. The local ER server MUST extract the DSRK, EMSKname, and DSRK lifetime if present, before forwarding the EAP-Success message to the peer, as specified in [12]. Note that the MSK (also present along with the EAP Success message) is extracted by the EAP authenticator as usual. The peer learns the domain name through EAP-Initiate/Re-auth-Start message or via lower layer announcements. When the domain name is available to the peer during or after the full EAP authentication, it attempts to use ERP when it associates with a new authenticator. If the peer does not know the domain name (did not receive the domain name via the lower layer announcement, due to a missed announcement or lack of support for domain name announcements in a specific lower layer), it SHOULD initiate ERP bootstrap exchange (ERP exchange with the bootstrap flag turned on) with the home ER server to obtain the Narayanan & Dondeti Expires August 28, 2008 [Page 15] Internet-Draft ERP February 2008 domain name. The local ER server behavior is the same as described above. The peer MAY also initiate bootstrapping to fetch information such as the rRK lifetime from the AAA server. The following steps describe the ERP explicit bootstrapping process: o The peer sends the EAP-Initiate/Re-auth message with the bootstrapping flag turned on. The bootstrap message is always sent to the home AAA server and the keyname-NAI attribute in the bootstrap message is constructed as follows: the username portion of the NAI contains the EMSKname and the realm portion contains the home domain name. o In addition, the message MUST contain a sequence number for replay protection, a cryptosuite, and an integrity checksum. The cryptosuite indicates the authentication algorithm. The integrity checksum indicates that the message originated at the claimed entity, the peer indicated by the Peer-ID, or the rIKname. o The peer MAY additionally set the lifetime flag to request the key lifetimes. o When an ERP-capable authenticator receives EAP-Initiate/Re-auth message from a peer, it copies the contents of the keyName-NAI into the User-Name attribute of RADIUS [13]. The rest of the process is similar to that described in [14] and described in [12]. o If a local ER server is present, the local ER server MUST include the DSRK request and its domain name in the AAA message encapsulating the EAP-Initiate/Re-auth message sent by the peer. o Upon receipt of an EAP-Initiate/Re-auth message, the server verifies whether the message is fresh or a replay by evaluating whether the received sequence number is equal to or greater than the expected sequence number for that rIK. The server then verifies to ensure that the cryptosuite used by the peer is acceptable. Next, it verifies the origin authentication of the message by looking up the rIK. If any of the checks fail, the server sends an EAP-Finish/Re-auth message with the Result flag set to '1'. Please refer to Section 5.2.2 for details on failure handling. This error MUST NOT have any correlation to any EAP- Success message that may have been received by the EAP authenticator and the peer earlier. If the EAP-Initiate/Re-auth message is well-formed and valid, the server prepares the EAP- Finish/Re-auth message. The bootstrap flag MUST be set to indicate that this is a bootstrapping exchange. The message contains the following fields: Narayanan & Dondeti Expires August 28, 2008 [Page 16] Internet-Draft ERP February 2008 * A sequence number for replay protection. * The same keyName-NAI as in the EAP-Initiate/Re-auth message. * If the lifetime flag was set in the EAP-Initiate/Re-auth message, the ER server SHOULD include the rRK lifetime and the rMSK lifetime in the EAP-Finish/Re-auth message. The server may have a local policy for the network to maintain and enforce lifetime unilaterally. In such cases, the server need not respond to the peer's request for the lifetime. * If the bootstrap flag is set and a DSRK request is received, the server MUST include the domain name to which the DSRK is being sent. * If the home ER server can directly verify the local ER server's authenticity and knows that only the local ER server gets access to the DSRK, it MAY include the Authorization Indication TLV. This is typically possible when there is end-to-end authentication between the home ER server and the local ER server. * An authentication tag MUST be included to prove that the EAP- Finish/Re-auth message originates at a server that possesses the rIK corresponding to the EMSKname-NAI. o If the ERP exchange is successful, and the local ER server sent a DSRK request, the home ER server MUST include the DSRK for the local ER server (derived using the EMSK and the domain name as specified in [3]), EMSKname and DSRK lifetime along with the EAP- Finish/Re-auth message. o In addition, the rMSK is sent along with the EAP-Finish/Re-auth message, in a AAA attribute [12]. o The local ER server MUST extract the DSRK, EMSKname, and DSRK lifetime if present, before forwarding the EAP-Finish/Re-auth message to the peer, as specified in [12]. o The authenticator receives the rMSK. o When the peer receives an EAP-Finish/Re-auth message with the bootstrap flag set, if a local domain name is present, it MUST use that to derive the appropriate DSRK, DS-rRK, DS-rIK and keyName- NAI, and initialize the replay counter for the DS-rIK. If not, the peer SHOULD derive the domain-specific keys using the domain name it learned via the lower layer or from the EAP-Initiate/ Re-auth-Start message. If the peer does not know the domain name, Narayanan & Dondeti Expires August 28, 2008 [Page 17] Internet-Draft ERP February 2008 it must assume that there is no local ER server available. o The peer MAY also verify the Authorization Indication TLV. o The procedures for encapsulating ERP and obtaining relevant keys using RADIUS and Diameter are specified in [12] and [15] respectively. Since the ER bootstrapping exchange is typically done immediately following the full EAP exchange, it is feasible that the process is completed through the same entity that served as the EAP authenticator for the full EAP exchange. In this case, the lower layer may already have established TSKs based on the MSK received earlier. The lower layer may then choose to ignore the rMSK that was received with the ER bootstrapping exchange. Alternatively, the lower layer may choose to establish a new TSK using the rMSK. In either case, the authenticator and the peer know which key is used based on the initiation or lack there of a TSK establishment exchange. The bootstrapping exchange may also be carried out via a new authenticator, in which case, the rMSK received SHOULD trigger a lower layer TSK establishment exchange. 5.2. Steps in ERP When a peer that has an active rRK and rIK associates with a new authenticator that supports ERP, it may perform an ERP exchange with that authenticator. ERP is typically a peer-initiated exchange, consisting of an EAP-Initiate/Re-auth and an EAP-Finish/Re-auth message. The ERP exchange may be performed with a local ER server (when one is present) or with the original EAP server. It is plausible for the network to trigger the EAP re-authentication process however. An ERP-capable authenticator SHOULD send an EAP- Initiate/Re-auth-Start message to indicate support for ERP. The peer may or may not wait for these messages to arrive to initiate the EAP- Initiate/Re-auth message. The EAP-Initiate/Re-auth-Start message SHOULD be sent by an ERP- capable authenticator. The authenticator may retransmit it a few times until it receives an EAP-Initiate/Re-auth message in response from the peer. The EAP-Initiate/Re-auth message from the peer may have originated before the peer receives either an EAP-Request/ Identity or an EAP-Initiate/Re-auth-Start message from the authenticator. Hence the Identifier value in the EAP-Initiate/ Re-auth message is independent of the Identifier value in the EAP- Initiate/Re-auth-Start or the EAP-Request/Identity messages. Operational Considerations at the Peer: Narayanan & Dondeti Expires August 28, 2008 [Page 18] Internet-Draft ERP February 2008 ERP requires that the peer maintain retransmission timers for reliable transport of EAP re-authentication messages. The reliability considerations of Section 4.3 of RFC 3748 apply with the peer as the retransmitting entity. The EAP Re-auth protocol has the following steps: The peer sends an EAP-Initiate/Re-auth message. At a minimum, the message SHALL include the following fields: a 16-bit sequence number for replay protection keyName-NAI as a TLV attribute to identify the rIK used to integrity protect the message. cryptosuite to indicate the authentication algorithm used to compute the integrity checksum. authentication tag over the message. When the peer is performing ERP with a local ER server, it MUST use the corresponding DS-rIK it shares with the local ER server. The peer SHOULD set the lifetime flag to request the key lifetimes from the server. The peer can use the rRK lifetime to know when to trigger an EAP method exchange and the rMSK lifetime to know when to trigger another ERP exchange. The authenticator copies the contents of the value field of the keyName-NAI TLV into the User-Name RADIUS attribute in the AAA message to the ER server. The server uses the keyName-NAI to lookup the rIK. It MUST first verify whether the sequence number is equal to or greater than the expected sequence number. If the server supports sequence number window size greater than 1, it MUST verify whether the sequence number falls within the window and has not been received before. The server MUST then verify to ensure that the cryptosuite used by the peer is acceptable. The server then proceeds to verify the integrity of the message using the rIK, thereby verifying proof of possession of that key by the peer. If any of these verifications fail, the server MUST send an EAP-Finish/Re-auth message with the Result flag set to '1' (Failure). Please refer to Section 5.2.2 for details on failure handling. Otherwise, it MUST compute an rMSK from the rRK using the sequence number as the additional input to the key derivation. In response to a well-formed EAP Re-auth/Initiate message, the server MUST send an EAP-Finish/Re-auth message with the following Narayanan & Dondeti Expires August 28, 2008 [Page 19] Internet-Draft ERP February 2008 considerations: a 16-bit sequence number for replay protection, which MUST be same as the received sequence number. The local copy of the sequence number MUST be incremented by 1. If the server supports multiple simultaneous ERP exchanges, it MUST instead update the sequence number window. keyName-NAI as a TLV attribute to identify the rIK used to integrity protect the message. cryptosuite to indicate the authentication algorithm used to compute the integrity checksum. authentication tag over the message. If the lifetime flag was set in the EAP-Initiate/Re-auth message, the ER server SHOULD include the rRK lifetime and the rMSK lifetime. The server transports the rMSK along with this message to the authenticator. The rMSK is transported in a manner similar to the MSK transport along with the EAP-Success message in a regular EAP exchange. The peer looks up the sequence number to verify whether it is expecting an EAP-Finish/Re-auth message with that sequence number protected by the keyName-NAI. It then verifies the integrity of the message. If the verifications fail, the peer logs an error and stops the process; otherwise, it proceeds to the next step. The peer uses the sequence number to compute the rMSK. The lower-layer security association protocol can be triggered at this point. 5.2.1. Multiple Simultaneous Runs of ERP When a peer is within the range of multiple authenticators, it may choose to run ERP via all of them simultaneously to the same ER server. In that case, it is plausible that the ERP messages may arrive out of order, resulting in the ER server rejecting legitimate EAP-Initiate/Re-auth messages. To facilitate such operation, an ER server MAY allow multiple simultaneous ERP exchanges by accepting all EAP-Initiate/Re-auth messages with SEQ number values within a window of allowed values. Recall that the SEQ number allows replay protection. Replay window Narayanan & Dondeti Expires August 28, 2008 [Page 20] Internet-Draft ERP February 2008 maintenance mechanisms are a local matter. 5.2.2. ERP Failure Handling If the processing of the EAP-Initiate/Re-auth message results in a failure, the ER server MUST send an EAP Finish Re-auth message with the Result flag set to '1'. If the server has a valid rIK for the peer, it MUST integrity protect the EAP-Finish/Re-auth failure message. If the failure is due to an unacceptable cryptosuite, the server SHOULD send a list of acceptable cryptosuites (in a TLV of Type 5) along with the EAP-Finish/Re-auth message. In this case, the server MUST indicate the cryptosuite used to protect the EAP-Finish/ Re-auth message in the cryptosuite. The rIK used with the EAP- Finish/Re-auth message in this case MUST be computed as specified in Section 4.3 using the new cryptosuite. If the server does not have a valid rIK for the peer, the EAP-Finish/Re-auth message indicating a failure will be unauthenticated; the server MAY include a list of acceptable cryptosuites in the message. The peer, upon receiving an EAP-Finish/Re-auth message with the Result flag set to '1', MUST verify the sequence number and the Authentication Tag to determine the validity of the message. If the peer supports the cryptosuite, it MUST verify the integrity of the received EAP-Finish/Re-auth message. If the EAP-Finish message contains a TLV of Type 5, the peer SHOULD retry the ERP exchange with a cryptosuite picked from the list included by the server. The peer MUST use the appropriate rIK for the subsequent ERP exchange, by computing it with the corresponding cryptosuite, as specified in Section 4.3. If the PRF in the chosen cryptosuite is different from the PRF originally used by the peer, it MUST derive a new DSRK (if required), rRK and rIK before proceeding with the subsequent ERP exchange. If the peer cannot verify the integrity of the received message, it MAY choose to retry the ERP exchange with one of the cryptosuites in the TLV of Type 5, after a failure has been clearly determined following the procedure in the next paragraph. If the replay or integrity checks fail, the failure message may have been sent by an attacker. It may also imply that the server and peer do not support the same cryptosuites; however, the peer cannot determine if that is the case. Hence, the peer SHOULD continue the ERP exchange per the retransmission timers before declaring a failure. When the peer runs explicit bootstrapping (ERP with the bootstrapping flag on), there may not be a local ER server available to send a DSRK Request and the domain name. In that case, the server cannot send Narayanan & Dondeti Expires August 28, 2008 [Page 21] Internet-Draft ERP February 2008 the DSRK and MUST NOT include the domain-name TLV. When the peer receives a response in the bootstrapping exchange without a domain- name TLV it assumes that there is no local ER server. The home ER server sends an rMSK to the ER authenticator however and the peer SHALL run the TSK establishment protocol as usual. 5.3. New EAP Packets Two new EAP Codes are defined for the purpose of ERP: EAP-Initiate and EAP-Finish. The packet format for these messages follows the EAP packet format defined in RFC3748 [2]. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Code | Identifier | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Type-Data ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- Figure 6: EAP Packet Code 5 Initiate 6 Finish Two new code values are defined for the purpose of ERP. Identifier The Identifier field is one octet. The Identifier field MUST be the same if an EAP-Initiate packet is retransmitted due to a timeout while waiting for a Finish message. Any new (non- retransmission) Initiate message MUST use a new Identifier field. The Identifier field of the Finish message MUST match that of the currently outstanding Initiate message. A Peer or Authenticator receiving a Finish message whose Identifier value does not match that of the currently outstanding Initiate message MUST silently discard the packet. In order to avoid confusion between new EAP-Initiate messages and retransmissions, the peer must choose a an Identifier value Narayanan & Dondeti Expires August 28, 2008 [Page 22] Internet-Draft ERP February 2008 that is different from the previous EAP-Initiate message, especially if that exchange has not finished. It is RECOMMENDED that the authenticator clear EAP Re-auth state after 300 seconds. Type This field indicates that this is an ERP exchange. Two type values are defined in this document for this purpose - Re-auth- Start (assigned Type 1), Re-auth (assigned Type 2). Type-Data The Type-Data field varies with the Type of re-authentication packet. 5.3.1. EAP-Initiate/Re-auth-Start Packet The EAP-Initiate/Re-auth-Start packet contains the parameters shown in Figure 7 : 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Code | Identifier | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Reserved | 1 or more TVs or TLVs ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 7: EAP-Initiate/Re-auth-Start Packet Type = 1. Reserved, MUST be zero. Set to zero on transmission and ignored on reception. One or more TVs or TLVs are used to convey information to the peer; for instance the authenticator may send domain name to the peer. TVs or TLVs: In the TV payloads, there is a 1-octet type payload and a value with type-specific length. In the TLV payloads, there is a 1-octet type payload and a 1-octet length payload. The length field indicates the length of the value expressed in number of octets. Narayanan & Dondeti Expires August 28, 2008 [Page 23] Internet-Draft ERP February 2008 Domain-Name: This is a TLV payload. The Type is 4. The domain name is to be used as the realm in an NAI [4]. Domain-Name attribute SHOULD be present in an EAP-Initiate/Re-auth-Start message. In addition channel binding information MAY be included: see Section 5.5 for additional discussion. See Figure 11 for parameter specification. 5.3.1.1. Authenticator Operation The authenticator MAY send the EAP-Initiate/Re-auth-Start message to indicate support for ERP to the peer and to initiate ERP if the peer has already performed full EAP authentication and has unexpired key material. The authenticator SHOULD include the domain name TLV to allow the peer to learn it without lower-layer support or the ERP bootstrapping exchange. The authenticator MAY include channel binding information so that the peer can send the information to the server in the EAP-Initiate/ Re-auth message so that the server can verify whether the authenticator is claiming the same identity to both parties. The authenticator MAY re-transmit the EAP-Initiate/Re-auth-Start message a few times for reliable transport. 5.3.1.2. Peer Operation The peer SHOULD send the EAP-Initiate/Re-auth message in response to the EAP-Initiate/Re-auth-Start message from the authenticator. If the peer does not recognize the Initiate code value, it silently discards the message. If the peer has already sent the EAP-Initiate/ Re-auth message to begin the ERP exchange, it silently discards the message. If the EAP-Initiate/Re-auth-Start message contains the domain name, and if the peer does not already have the domain information, the peer SHOULD use the domain name to compute the DSRK and use the corresponding DS-rIK to send an EAP-Initiate/Re-auth message to start an ERP exchange with the local ER server. If the peer has already initiated ERP exchange with the home ER server, it MAY choose to not start an ERP exchange with the local ER server. 5.3.2. EAP-Initiate/Re-auth Packet The EAP-Initiate/Re-auth packet contains the parameters shown in Figure 8 : Narayanan & Dondeti Expires August 28, 2008 [Page 24] Internet-Draft ERP February 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Code | Identifier | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type |R|B|L| Reserved| SEQ | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 1 or more TVs or TLVs ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | cryptosuite | Authentication Tag ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 8: EAP-Initiate/Re-auth Packet Type = 2. Flags 'R' - The R flag is set to 0 and ignored upon reception. 'B' - The B flag is used as the bootstrapping flag. If the flag is turned on, the message is a bootstrap message. 'L' - The L flag is used to request the key lifetimes from the server. The rest of the 5 bits are set to 0 and ignored on reception. SEQ: A 16-bit sequence number is used for replay protection. The SEQ number field is initialized to zero every time a new rRK is derived. TVs or TLVs: In the TV payloads, there is a 1-octet type payload and a value with type-specific length. In the TLV payloads, there is a 1-octet type payload and a 1-octet length payload. The length field indicates the length of the value expressed in number of octets. keyName-NAI: This is carried in a TLV payload. The Type is 1. The NAI is variable in length, not exceeding 253 octets. EMSKname is in the username part of the NAI and is encoded in hexadecimal values. The EMSKname is 64-bits in length and so the username portion takes up 128 octets. If the rIK is derived from the EMSK, the realm part of the NAI is the home domain name and if the rIK is derived from a DSRK, the realm Narayanan & Dondeti Expires August 28, 2008 [Page 25] Internet-Draft ERP February 2008 part of the NAI is the domain name used in the derivation of the DSRK. The NAI syntax follows [4]. Exactly one keyName-NAI attribute SHALL be present in an EAP-Iniaite/Re-auth packet. In addition channel binding information MAY be included: see Section 5.5 for additional discussion. See Figure 11 for parameter specification. Cryptosuite: This field indicates the integrity algorithm used for ERP. Key lengths and output lengths are either indicated or are obvious from the cryptosuite name. We specify some cryptosuites below: * 0 RESERVED * 1 HMAC-SHA256-64 * 2 HMAC-SHA256-128 * 3 HMAC-SHA256-256 HMAC-SHA256-128 is mandatory to implement and should be enabled in the default configuration. Authentication Tag: This field contains the integrity checksum over the ERP packet, excluding the authentication tag field itself. The length of the field is indicated by the Cryptosuite. 5.3.3. EAP Finish/Re-auth Packet The EAP-Finish/Re-auth packet contains the parameters shown in Figure 9 : 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Code | Identifier | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type |R|B|L| Reserved | SEQ ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 1 or more TVs or TLVs ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | cryptosuite | Authentication Tag ~ +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 9: EAP Finish/Re-auth Packet Narayanan & Dondeti Expires August 28, 2008 [Page 26] Internet-Draft ERP February 2008 Type = 2. Flags 'R' - The R flag is used as the Result flag - when set to 0, it indicates success and when set to '1', it indicates a failure. 'B' - The B flag is used as the bootstrapping flag. If the flag is turned on, the message is a bootstrap message. 'L' - The L flag is used to indicate the presence of the rRK lifetime TLV. The rest of the 5 bits are set to 0 and ignored on reception. SEQ: A 16-bit sequence number is used for replay protection. The SEQ number field is initialized to zero every time a new rRK is derived. TVs or TLVs: In the TV payloads, there is a 1-octet type payload and a value with type-specific length. In the TLV payloads, there is a 1-octet type payload and a 1-octet length payload. The length field indicates the length of the value expressed in number of octets. keyName-NAI: This is carried in a TLV payload. The Type is 1. The NAI is variable in length, not exceeding 253 octets. EMSKname is in the username part of the NAI and is encoded in hexadecimal values. The EMSKname is 64-bits in length and so the username portion takes up 16 octets. If the rIK is derived from the EMSK, the realm part of the NAI is the home domain name and if the rIK is derived from a DSRK, the realm part of the NAI is the domain name used in the derivation of the DSRK. The NAI syntax follows [4]. Exactly one instance of the keyName-NAI attribute SHALL be present in an EAP-Finish/Re-auth message. rRK Lifetime: This is a TV payload. The Type is 2. The value field is a 32-bit field and contains the lifetime of the rRK in seconds. If the 'L' flag is set, the rRK Lifetime attribute SHOULD be present. rMSK Lifetime: This is a TV payload. The Type is 3. The value field is a 32-bit field and contains the lifetime of the rMSK in seconds. If the 'L' flag is set, the rMSK Lifetime attribute SHOULD be present. Narayanan & Dondeti Expires August 28, 2008 [Page 27] Internet-Draft ERP February 2008 Domain-Name: This is a TLV payload. The Type is 4. The domain name is to be used as the realm in an NAI [4]. Domain-Name attribute MUST be present in an EAP-Finish/Re-auth message if the bootstrapping flag is set and if the local ER server sent a DSRK request. List of cryptosuites: This is a TLV payload. The Type is 5. The value field contains a list of cryptosuites, each of size 1 octet. The cryptosuite values are as specified in Figure 8. The server SHOULD include this attribute if the cryptosuite used in the EAP-Initiate/Re-auth message was not acceptable and the message is being rejected. The server MAY include this attribute in other cases. The server MAY use this attribute to signal to the peer about its cryptographic algorithm capabilities. Authorization Indication: This is a TLV payload. The Type is 6. This attribute MAY be included when a DSRK is delivered to a local ER server and if the home ER server can directly authenticate the local ER server and can assure to the peer that only the authorized local ER server shall receive the DSRK. The value contains an authentication tag computed over the entire packet, starting from the first bit of the code field to the last bit of the crypto-suite field, with the value field filled with all 0s for the computation. The key used for the computation MUST be derived from the EMSK with key label "DSRK Delivery Authorized Key@ietf.org" and optional data containing an ASCII string representing the key management domain that the DSRK is being derived for. In addition channel binding information MAY be included: see Section 5.5 for additional discussion. See Figure 11 for parameter specification. The server sends this information so that the peer can verify the information seen at the lower layer, if channel binding is to be supported. Cryptosuite: This field indicates the integrity algorithm and the PRF used for ERP. Key lengths and output lengths are either indicated or are obvious from the cryptosuite name. Authentication Tag: This field contains the integrity checksum over the ERP packet, excluding the authentication tag field itself. The length of the field is indicated by the Cryptosuite. Narayanan & Dondeti Expires August 28, 2008 [Page 28] Internet-Draft ERP February 2008 5.3.4. TV and TLV Attributes The TV attributes that may be present in the EAP-Initiate or EAP- Finish messages are of the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Value ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 10: TV Attribute Format The TLV attributes that may be present in the EAP-Initiate or EAP- Finish messages are of the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | Value ... +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Figure 11: TLV Attribute Format The following Types are defined in this document: '1' - keyName-NAI: This is a TLV Payload '2' - rRK Lifetime: This is a TV payload '3' - rMSK Lifetime: This is a TV payload '4' - domain name: This is a TLV payload '5' - cryptosuite list: This is a TLV payload '6' - Authorization Indication: This is a TLV payload The TLV type range of 128-191 is reserved to carry channel binding information in the EAP-Initiate and Finish/Re-auth messages. Below are the current assignments (all of them are TLVs): Narayanan & Dondeti Expires August 28, 2008 [Page 29] Internet-Draft ERP February 2008 '128' - Called-Station-Id [13] '129' - Calling-Station-Id [13] '130' - NAS-Identifier [13] '131' - NAS-IP-Address [13] '132' - NAS-IPv6-Address [16] The length field indicates the length of the value part of the attribute in octets. 5.4. Replay Protection For replay protection, ERP uses sequence numbers. The sequence number is maintained per rIK and is initialized to zero in both directions. In the first EAP-Initiate/Re-auth message, the peer uses the sequence number zero or higher. Note that the when the sequence number rotates, the rIK MUST be changed by running EAP authentication. The server expects a sequence number of zero or higher. When the server receives an EAP-Initiate/Re-auth message, it uses the same sequence number in the EAP-Finish/Re-auth message. The server then sets the expected sequence number to the received sequence number plus 1. The server accepts sequence numbers greater than or equal to the expected sequence number. If the peer sends an EAP-Initiate/Re-auth message, but does not receive a response, it retransmits the request (with no changes to the message itself) a pre-configured number of times before giving up. However, it is plausible that the server itself may have responded to the message and it was lost in transit. Thus the peer MUST increment the sequence number and use the new sequence number to send subsequent EAP re-authentication messages. The peer SHOULD increment the sequence number by 1; however, it may choose to increment by a larger number. When the sequence number rotates, the peer MUST run full EAP authentication. 5.5. Channel Binding ERP provides a protected facility to carry channel binding (CB) information, according to the guidelines in Section 7.15 of [2]. The TLV type range of 128-191 is reserved to carry CB information in the EAP-Initiate/Re-auth and EAP-Finish/Re-auth messages. Called- Station-Id, Calling-Station-Id, NAS-Identifier, NAS-IP-Address, and NAS-IPv6-Address are some examples of channel binding information listed in RFC 3748 and they are assigned values 128-132. Additional values are IANA managed based on IETF Consensus [17]. Narayanan & Dondeti Expires August 28, 2008 [Page 30] Internet-Draft ERP February 2008 The authenticator MAY provide CB information to the peer via the EAP- Initiate/Re-auth-Start message. The peer sends the information to the server in the EAP-Initiate/Re-auth message; the server verifies whether the authenticator identity available via AAA attributes is the same as the identity provided to the peer. If the peer does not include the CB information in the EAP-Initiate/ Re-auth message, and if the local ER server's policy requires channel binding support, it SHALL send the CB attributes for the peer's verification. The peer attempts to verify the CB information if the authenticator has sent the CB parameters and proceeds with the lower layer security association establishment if the attributes match. Otherwise, the peer SHALL NOT proceed with the lower layer security association establishment. 6. Lower Layer Considerations The authenticator is responsible for retransmission of EAP-Initiate/ Re-auth-Start messages. The authenticator MAY retransmit the message a few times or until it receives an EAP-Initiate/Re-auth message from the peer. The authenticator may not know whether the peer supports ERP; in those cases, the peer may be silently dropping the EAP- Initiate/Re-auth-Start packets. Thus retransmission of these packets should be kept to a minimum. The exact number is up to each lower layer. The Identifier value in the EAP-Initiate/Re-auth packet is independent of the Identifier value in the EAP-Initiate/Re-auth-Start packet. The peer is responsible for retransmission of EAP-Initiate/Re-auth messages. Retransmitted packets MUST be sent with the same Identifier value in order to distinguish them from new packets. By default, where the EAP-Initiate message is sent over an unreliable lower layer, the retransmission timer SHOULD be dynamically estimated. A maximum of 3-5 retransmissions is suggested (this is based on the recommendation of [2]). Where the EAP-Initiate message is sent over a reliable lower layer, the retransmission timer SHOULD be set to an infinite value, so that retransmissions do not occur at the EAP layer. Please refer to RFC3748 [2] for additional guidance on setting timers. The Identifier value in the EAP-Finish/Re-auth packet is the same as the Identifier value in the EAP-Initiate/Re-auth packet. If an authenticator receives a valid duplicate EAP-Initiate/Re-auth Narayanan & Dondeti Expires August 28, 2008 [Page 31] Internet-Draft ERP February 2008 message for which it has already sent an EAP-Finish/Re-auth message, it MUST resend the EAP-Finish/Re-auth message without reprocessing the EAP-Initiate/Re-auth message. To facilitate this, the authenticator SHALL store a copy of the EAP-Finish/Re-auth message for a finite amount of time. The actual value of time is a local matter; this specification recommends a value of 100 milliseconds. The lower layer may provide facilities for exchanging information between the peer and the authenticator about support for ERP, for the authenticator to send the domain name information and channel binding information to the peer Note that lower layer specifications may need to be revised to allow carrying EAP messages that have a code value higher than 4 and to accommodate the peer-initiated nature of ERP. 7. Transport of ERP Messages AAA Transport of ERP messages is specified in [11] and [12]. 8. Security Considerations This section provides an analysis of the protocol in accordance with the AAA key management requirements specified in [18]. Cryptographic algorithm independence The EAP Re-auth protocol satisfies this requirement. The algorithm chosen by the peer for the MAC generation is indicated in the EAP-Initiate/Re-auth message. If the chosen algorithm is unacceptable, the EAP server returns an EAP- Finish/Re-auth message with Failure indication. Algorithm agility for the KDF is specified in [3]. Only when the algorithms used are acceptable, the server proceeds with derivation of keys and verification of the proof of possession of relevant keying material by the peer. A full blown negotiation of algorithms cannot be provided in a single round trip protocol. Hence, while the protocol provides algorithm agility, it does not provide true negotiation. Strong, fresh session keys ERP results in the derivation of strong, fresh keys that are unique for the given session. An rMSK is always derived on- demand when the peer requires a key with a new authenticator. The derivation ensures that the compromise of one rMSK does not Narayanan & Dondeti Expires August 28, 2008 [Page 32] Internet-Draft ERP February 2008 result in the compromise of a different rMSK at any time. Limit key scope The scope of all the keys derived by ERP is well defined. The rRK and rIK are never shared with any entity and always remain on the peer and the server. The rMSK is provided only to the authenticator through which the peer performs the ERP exchange. No other authenticator is authorized to use that rMSK. Replay detection mechanism For replay protection of ERP messages, a sequence number associated with the rIK is used. The sequence number is maintained by the peer and the server, and initialized to zero when the rIK is generated. The peer increments the sequence number by one after it sends an ERP message. The server sets the expected sequence number to received sequence number plus one after verifying the validity of the received message and responds to the message. Authenticate all parties The EAP Re-auth protocol provides mutual authentication of the peer and the server. Both parties need to possess the keying material that resulted from a previous EAP exchange in order to successfully derive the required keys. Also, both the EAP re- authentication Response and the EAP re-authentication Information messages are integrity protected so that the peer and the server can verify each other. When the ERP exchange is executed with a local ER server, the peer and the local server mutually authenticate each other via that exchange in the same manner. The peer and the authenticator authenticate each other in the secure association protocol executed by the lower layer just as in the case of a regular EAP exchange. Peer and authenticator authorization The peer and authenticator demonstrate possession of the same key material without disclosing it, as part of the lower layer secure association protocol. Channel binding with ERP may be used to verify consistency of the identities exchanged, when the identities used in the lower layer differ from that exchanged within the AAA protocol. Keying material confidentiality Narayanan & Dondeti Expires August 28, 2008 [Page 33] Internet-Draft ERP February 2008 The peer and the server derive the keys independently using parameters known to each entity. The AAA server sends the DSRK of a domain to the corresponding local ER server via the AAA protocol. Likewise, the ER server sends the rMSK to the authenticator via the AAA protocol. Note that compromise of the DSRK results in compromise of all keys derived from it. Moreover, there is no forward secrecy within ERP. Thus, compromise of an DSRK retroactively compromises all ERP keys. It is RECOMMENDED that the AAA protocol be protected using IPsec or TLS so that the keys are protected in transit. Note however that keys may be exposed to AAA proxies along the way and compromise of any of those proxies may result in compromise of keys being transported through them. When the server can directly verify the authenticity of the entity that receives the DSRK and if it knows that no other entity can receive the DSRK, it includes the Authorization Indication TLV to assure the peer that DSRK delivery is secure. If the Authorization Indication TLV is not present, the peer has no such assurance and assumes that DSRK misuse might be plausible. Confirm cryptosuite selection Crypto algorithms for integrity and key derivation in the context of ERP MAY be the same as that used by the EAP method. In that case, the EAP method is responsible for confirming the cryptosuite selection. Furthermore, the cryptosuite is included in the ERP exchange by the peer and confirmed by the server. The protocol allows the server to reject the cryptosuite selected by the peer and provide alternatives. When a suitable rIK is not available for the peer, the alternatives may be sent in an unprotected fashion. The peer is allowed to retry the exchange using one of the allowed cryptosuites. However, any enroute modifications of the list sent by the server in this case will go undetected. If the server does have an rIK available for the peer, the list will be provided in a protected manner and this issue does not apply. Uniquely named keys All keys produced within the ERP context can be referred to uniquely as specified in this document. Also, the key names do not reveal any part of the keying material. Narayanan & Dondeti Expires August 28, 2008 [Page 34] Internet-Draft ERP February 2008 Prevent the domino effect The compromise of one peer does not result in the compromise of keying material held by any other peer in the system. Also, the rMSK is meant for a single authenticator and is not shared with any other authenticator. Hence, the compromise of one authenticator does not lead to the compromise of sessions or keys held by any other authenticator in the system. Hence, the EAP Re-auth protocol allows prevention of the domino effect by appropriately defining key scope. However, if keys are transported using hop-by-hop protection, compromise of a proxy may result in compromise of key material, DSRK, sent to a local ER server. Bind key to its context All the keys derived for ERP are bound to the appropriate context using appropriate key labels. Lifetime of a child key is less than or equal to that of its parent key as specified in RFC 4962 [18]. The key usage, lifetime and the parties that have access to the keys are specified. Confidentiality of identity Deployments where privacy is a concern may find the use of rIKname-NAI to route ERP messages serves their privacy requirements. Note that it is plausible to associate multiple runs of ERP messages since the rIKname is not changed as part of the ERP protocol. There was no consensus for that requirement at the time of development of this specification. If the rIKname is not used and the Peer-ID is used instead, the ERP exchange will reveal the Peer-ID over the wire. Authorization restriction All the keys derived are limited in lifetime by that of the parent key or by server policy. Any domain specific keys are further restricted for use only in the domain for which the keys are derived. All the keys specified in this document are meant for use in ERP only. Any other restrictions of session keys may be imposed by the specific lower layer and is out of scope for this specification. A denial of service attack on the peer may be possible when using the EAP Initiate/Re-auth message. An attacker may send a bogus EAP- Initiate/Re-auth message, which may be carried by the authenticator in a RADIUS-Access-Request to the server; in response to that the Narayanan & Dondeti Expires August 28, 2008 [Page 35] Internet-Draft ERP February 2008 server may send an EAP-Finish/Re-auth with Failure indication in a RADIUS Access-Reject message. Note that such attacks may be plausible with the EAPoL-Start capability of IEEE 802.11 and other similar facilities in other link layers and where the peer can initiate EAP authentication; an attacker may use such messages to start an EAP method run, which fails and may result in the server sending a RADIUS Access-Reject message and thus resulting in the link layer connections being terminated. To prevent such DoS attacks, an ERP failure should not result in deletion of any authorization state established by a full EAP exchange. Alternatively, the lower layers and AAA protocols may define mechanisms to allow two link layer SAs derived from different EAP keying materials for the same peer to exist so that smooth migration from the current link layer SA to the new one is possible during rekey. These mechanisms prevent the link layer connections from being terminated when a re-authentication procedure fails due to the bogus EAP-Initiate/Re-auth message. When a DSRK is sent from a home ER server to a local domain server or when a rMSK is sent from an ER server to an authenticator, in the absence of end-to-end security between the entity that is sending the key and the entity receiving the key, it is plausible for other entities to get access to keys being sent to an ER server in another domain. This mode of key transport is similar to that of MSK transport in the context of EAP authentication. We further observe that ERP is for access authentication and does not support end-to-end data security. In typical implementations, the traffic is as such in the clear beyond the access control enforcement point, typically the authenticator or a delegate thereof. The model works as long as entities in the middle of the network do not use keys intended for other parties to steal service from an access network. If that is not achievable, key delivery must be protected in an end-to-end manner. 9. IANA Considerations This document specifies IANA registration of two new 'Packet Codes' from the EAP registry: o 5 (Initiate) o 6 (Finish) These values are in accordance with [2]. This document also specifies creation of a new table, Message Types, Narayanan & Dondeti Expires August 28, 2008 [Page 36] Internet-Draft ERP February 2008 in the EAP registry with the following assigned numbers: o 0 Reserved o 1 (Re-auth-Start, applies to Initiate Code only), o 2 (Re-auth, applies to Initiate and Finish Codes). o 3-191 IANA managed and assigned based on IETF Consensus [17], o 192-255 Experimental/Private use. . Next, we specify creation of a new table, EAP Initiate and Finish Attributes, associated with EAP Initiate and Finish messages in the EAP registry with the following assigned numbers. o 0: Reserved o keyName-NAI: This is a TLV payload. The Type is 1. o rRK Lifetime: This is a TV payload. The Type is 2. o rMSK Lifetime: This is a TV payload. The Type is 3. o Domain name: This is a TLV payload. The Type is 4. o Cryptosuite list: This is a TLV payload. The Type is 5. o Authorization Indication: This is a TLV payload. The Type is 6. o 7-127: Used to carry other non-channel binding related attributes. IANA managed and assigned based on IETF Consensus [17]. o The TLV type range of 128-191 is reserved to carry CB information in the EAP-Initiate/Re-auth and EAP-Finish/Re-auth messages. Below are the current assignments (all of them are TLVs): * Called-Station-Id: 128 * Calling-Station-Id: 129 * NAS-Identifier: 130 * NAS-IP-Address: 131 Narayanan & Dondeti Expires August 28, 2008 [Page 37] Internet-Draft ERP February 2008 * NAS-IPv6-Address: 132 133-191 Used to carry other channel binding related attributes. IANA managed and assigned based on IETF Consensus [17]. o 192-255 is reserved for Experimental/Private use. We specify creation of another registry 'Re-authentication Cryptosuites' with the following assigned numbers: o 0 Reserved o 1 HMAC-SHA256-64 o 2 HMAC-SHA256-128 o 3 HMAC-SHA256-256 o 4-191 IANA managed and assigned based on IETF consensus [17] o 192-255 is reserved for Experimental/Private use. Further, this document registers a Re-auth usage label from the "USRK key labels" name space with a value EAP Re-authentication Root Key@ietf.org and DSRK authorized delivery key from the "USRK key labels" name space DSRK Delivery Authorized Key@ietf.org in accordance with [3]. 10. Acknowledgments In writing this draft, we benefited from discussing the problem space and the protocol itself with a number of folks including, Bernard Aboba, Jari Arkko, Sam Hartman, Russ Housley, Joe Salowey, Jesse Walker, Charles Clancy, Michaela Vanderveen, Kedar Gaonkar, Parag Agashe, Dinesh Dharmaraju, Pasi Eronen, Dan Harkins, Yoshi Ohba, Glen Zorn, Alan DeKok, Katrin Hoeper and other participants of the HOKEY working group. The credit for the idea to use EAP-Initiate/ Re-auth-Start goes to Charles Clancy and the multiple link layer SAs idea to mitigate the DoS attack goes to Yoshi Ohba. Katrin Hoeper suggested the use of windowing technique to handle multiple simultaneous ER exchanges. Many thanks to Pasi Eronen for the Narayanan & Dondeti Expires August 28, 2008 [Page 38] Internet-Draft ERP February 2008 suggestion to use hexadecimal encoding for rIKname when sent as part of keyName-NAI field. Thanks to Bernard Aboba for suggestions in clarifying the EAP lock step operation and Joe Salowey and Glen Zorn for help in specifying AAA transport of ERP messages. Thanks to Sam Hartman for the DSRK Authorization Indication mechanism. 11. References 11.1. Normative References [1] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [2] Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H. Levkowetz, "Extensible Authentication Protocol (EAP)", RFC 3748, June 2004. [3] Salowey, J., Dondeti, L., Narayanan, V., and M. Nakhjiri, "Specification for the Derivation of Root Keys from an Extended Master Session Key (EMSK)", draft-ietf-hokey-emsk-hierarchy-04 (work in progress), February 2008. [4] Aboba, B., Beadles, M., Arkko, J., and P. Eronen, "The Network Access Identifier", RFC 4282, December 2005. [5] Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed-Hashing for Message Authentication", RFC 2104, February 1997. 11.2. Informative References [6] Arkko, J. and H. Haverinen, "Extensible Authentication Protocol Method for 3rd Generation Authentication and Key Agreement (EAP-AKA)", RFC 4187, January 2006. [7] Lopez, R., Skarmeta, A., Bournelle, J., Laurent-Maknavicus, M., and J. Combes, "Improved EAP keying framework for a secure mobility access service", IWCMC '06 Proceedings of the 2006 international conference on Wireless communications and mobile computing, New York, NY, USA, 2006. [8] Arbaugh, W. and B. Aboba, "Experimental Handoff Extension to RADIUS", draft-irtf-aaaarch-handoff-04 (work in progress), November 2003. [9] Clancy, C., Nakhjiri, M., Narayanan, V., and L. Dondeti, "Handover Key Management and Re-authentication Problem Statement", draft-ietf-hokey-reauth-ps-09 (work in progress), Narayanan & Dondeti Expires August 28, 2008 [Page 39] Internet-Draft ERP February 2008 February 2008. [10] Institute of Electrical and Electronics Engineers, "IEEE Standards for Local and Metropolitan Area Networks: Port based Network Access Control, IEEE Std 802.1X-2004", Dec 2004. [11] Nakhjiri, M. and Y. Ohba, "Derivation, delivery and management of EAP based keys for handover and re-authentication", draft-ietf-hokey-key-mgm-02 (work in progress), January 2008. [12] Gaonkar, K., Dondeti, L., and V. Narayanan, "RADIUS attributes for Domain-specific Key Request and Delivery", draft-gaonkar-radext-erp-attrs-02 (work in progress), December 2007. [13] Rigney, C., Willens, S., Rubens, A., and W. Simpson, "Remote Authentication Dial In User Service (RADIUS)", RFC 2865, June 2000. [14] Aboba, B. and P. Calhoun, "RADIUS (Remote Authentication Dial In User Service) Support For Extensible Authentication Protocol (EAP)", RFC 3579, September 2003. [15] Dondeti, L. and H. Tschofenig, "Diameter Support for EAP Re- authentication Protocol", draft-dondeti-dime-erp-diameter-01 (work in progress), November 2007. [16] Aboba, B., Zorn, G., and D. Mitton, "RADIUS and IPv6", RFC 3162, August 2001. [17] Narten, T. and H. Alvestrand, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 2434, October 1998. [18] Housley, R. and B. Aboba, "Guidance for Authentication, Authorization, and Accounting (AAA) Key Management", BCP 132, RFC 4962, July 2007. Appendix A. Example ERP Exchange Narayanan & Dondeti Expires August 28, 2008 [Page 40] Internet-Draft ERP February 2008 0. Authenticator --> Peer: [EAP-Initiate/Re-auth-Start] 1. Peer --> Authenticator: EAP Initiate/Re-auth(SEQ, keyName-NAI, cryptosuite,Auth-tag*) 1a. Authenticator --> Re-auth-Server: AAA-Request{Authenticator-Id, EAP Initiate/Re-auth(SEQ,keyName-NAI, cryptosuite,Auth-tag*) 2. ER-Server --> Authenticator: AAA-Response{rMSK, EAP-Finish/Re-auth(SEQ,keyName-NAI, cryptosuite,[CB-Info],Auth-tag*) 2b. Authenticator --> Peer: EAP-Finish/Re-auth(SEQ,keyName-NAI, cryptosuite,[CB-Info],Auth-tag*) * Auth-tag computation is over the entire EAP Initiate/Finish message; the code values for Initiate and Finish are different and thus reflection attacks are mitigated. Figure 12: ERP Exchange Authors' Addresses Vidya Narayanan Qualcomm, Inc. 5775 Morehouse Dr San Diego, CA USA Phone: +1 858-845-2483 Email: vidyan@qualcomm.com Lakshminath Dondeti Qualcomm, Inc. 5775 Morehouse Dr San Diego, CA USA Phone: +1 858-845-1267 Email: ldondeti@qualcomm.com Narayanan & Dondeti Expires August 28, 2008 [Page 41] Internet-Draft ERP February 2008 Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Acknowledgment Funding for the RFC Editor function is provided by the IETF Administrative Support Activity (IASA). Narayanan & Dondeti Expires August 28, 2008 [Page 42]