GEOPRIV Working Group J. Polk
INTERNET-DRAFT Cisco Systems
Obsoletes: 3825 (if approved) J. Schnizlein
Category: Standards Track Individual Contributor
Expires: July 25, 2011 M. Linsner
25 January 2011 Cisco Systems
M. Thomson
Andrew
B. Aboba (ed)
Microsoft Corporation
Dynamic Host Configuration Protocol Options for
Coordinate-based Location Configuration Information
draft-ietf-geopriv-rfc3825bis-16.txt
Abstract
This document specifies Dynamic Host Configuration Protocol Options
(both DHCPv4 and DHCPv6) for the coordinate-based geographic location
of the client. The Location Configuration Information (LCI) includes
Latitude, Longitude, and Altitude, with resolution or uncertainty
indicators for each. Separate parameters indicate the reference
datum for each of these values. This document obsoletes RFC 3825.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on July 25, 2011.
Polk, et al. Standards Track [Page 1]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Polk, et al. Standards Track [Page 2]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Conventions . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Resolution and Uncertainty . . . . . . . . . . . . . . . 5
2. DHCP Option Format . . . . . . . . . . . . . . . . . . . . . . 6
2.1 DHCPv6 Option . . . . . . . . . . . . . . . . . . . . . 6
2.2 DHCPv4 Options . . . . . . . . . . . . . . . . . . . . . 8
2.3 Latitude and Longitude Fields . . . . . . . . . . . . . 11
2.4 Altitude . . . . . . . . . . . . . . . . . . . . . . . . 14
2.5 Datum . . . . . . . . . . . . . . . . . . . . . . . . . 16
3. Security Considerations. . . . . . . . . . . . . . . . . . . . 16
4. IANA Considerations. . . . . . . . . . . . . . . . . . . . . . 17
5. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 18
6. References . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6.1. Normative References . . . . . . . . . . . . . . . . . . 18
6.2. Informational References . . . . . . . . . . . . . . . . 19
Appendix A. GML Mapping . . . . . . . . . . . . . . . . . . . . . 21
A.1. GML Templates . . . . . . . . . . . . . . . . . . . . . 21
Appendix B. Calculations of Resolution . . . . . . . . . . . . . . 24
B.1. LCI of "White House" (Example 1) . . . . . . . . . . . . 25
B.2. LCI of "Sears Tower" (Example 2) . . . . . . . . . . . . 27
Appendix C. Calculations of Uncertainty . . . . . . . . . . . . . 28
C.1 LCI of "Sydney Opera House" (Example 3) . . . . . . . . 28
Appendix D. Changes from RFC 3825 . . . . . . . . . . . . . . . . 32
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 33
Polk, et al. Standards Track [Page 3]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
1. Introduction
The physical location of a network device has a range of
applications. In particular, emergency telephony applications rely
on knowing the location of a caller in order to determine the correct
emergency center.
The location of a device can be represented either in terms of
geospatial (or geodetic) coordinates, or as a civic address.
Different applications may be more suited to one form of location
information; therefore, both the geodetic and civic forms may be used
simultaneously.
This document specifies Dynamic Host Configuration Protocol v4
(DHCPv4) [RFC2131] and DHCPv6 [RFC3315] options for the coordinate-
based geographic location of the client, to be provided by the
server. "Dynamic Host Configuration Protocol (DHCPv4 and DHCPv6)
Option for Civic Addresses Configuration Information" [RFC4776]
specifies DHCP options for civic addresses.
The geodetic coordinate options defined in this document and the
civic address options defined in RFC 4776 [RFC4776] enable a DHCP
client to obtain its location. For example, a wired Ethernet host
might use these options for location determination. In this case,
the location information could be derived from a wiremap by the DHCP
server, using the Circuit-ID Relay Agent Information Option (RAIO)
defined (as Sub-Option 1) in RFC 3046 [RFC3046]. The DHCP server
could correlate the Circuit-ID with the geographic location where the
identified circuit terminates (such as the location of the wall
jack).
The mechanism defined here may also be utilized to provide location
to wireless hosts. DHCP relay agent sub-options (RAIO) [RFC3046] is
one method a DHCP server might use to perform host location
determination. Currently, the relay agent sub-options do not include
data sets required for device level location determination of
wireless hosts. In cases where the DHC server uses RAIO for location
determination, a wireless host can use this mechanism to discover
location of the radio access point, or the area of coverage for the
radio access point.
An important feature of this specification is that after the relevant
DHCP exchanges have taken place, the location information is stored
on the end device rather than somewhere else, where retrieving it
might be difficult in practice.
Polk, et al. Standards Track [Page 4]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
1.1. Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
1.2. Resolution and Uncertainty
The DHCP options defined in this document include fields quantifying
the resolution or uncertainty associated with a target location. No
inferences relating to privacy policies can be drawn from either
uncertainty or resolution values.
As utilized in this document, resolution refers to the accuracy of a
reported location, as expressed by the number of valid bits in each
of the Latitude, Longitude and Altitude fields.
In the context of location technology, uncertainty is a
quantification of errors. Any method for determining location is
subject to some sources of error; uncertainty describes the amount of
error that is present. Uncertainty might be the coverage area of a
wireless transmitter, the extent of a building or a single room.
Uncertainty is usually represented as an area within which the target
is located. In this document, each of the three axes can be assigned
an uncertainty value. In effect, this describes a rectangular prism,
which may be used as a coarse representation of a more complex shape
that fits within it. See Section 2.3.2 for more detail on the
correspondence between shapes and uncertainty.
When representing locations from sources that can quantify
uncertainty, the goal is to find the smallest possible rectangular
prism that this format can describe. This is achieved by taking the
minimum and maximum values on each axis and ensuring that the final
encoding covers these points. This increases the region of
uncertainty, but ensures that the region that is described
encompasses the target location.
The DHCPv4 option formats defined in this document support resolution
and uncertainty parameters. DHCPv4 Option 123 includes a resolution
parameter for each of the dimensions of location. Since this
resolution parameter need not apply to all dimensions equally, a
resolution value is included for each of the three location elements.
DHCPv4 Option TBD as well as the DHCPv6 option format utilize an
uncertainty parameter.
Appendix A describes the mapping of DHCP option values to the
Geography Markup Language (GML). Appendix B of this document
Polk, et al. Standards Track [Page 5]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
provides examples showing the calculation of resolution values.
Appendix C provides an example demonstrating calculation of
uncertainty values.
Since the Presence Information Data Format Location Object (PIDF-LO)
[RFC4119][RFC5491] is used to conveying location and the associated
uncertainty within an emergency call [Convey], a mechanism is needed
to convert the information contained within the DHCPv4 and DHCPv6
options to PIDF-LO. This document describes the following
conversions:
DHCPv4 Option 123 to PIDF-LO
DHCPv4 Option TBD and DHCPv6 option to PIDF-LO
PIDF-LO to DHCP Option TBD and DHCPv6 option
Conversion to PIDF-LO does not increase uncertainty; conversion from
PIDF-LO to DHCPv4 Option TBD and the DHCPv6 option increases
uncertainty by less than a factor of 2 in each dimension. Since it
is not possible to translate an arbitrary PIDF-LO to DHCP Option 123
with a bounded increase in uncertainty, the conversion is not
specified.
2. DHCP Option Format
This section defines the format for the DHCPv4 and DHCPv6 options.
These options utilize a similar format, differing primarily in the
option code.
2.1. DHCPv6 Option
The DHCPv6 [RFC3315] option format is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option Code (TBD) | OptLen |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LatUnc | Latitude +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Lat (cont'd) | LongUnc | Longitude +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Longitude (cont'd) | AType | AltUnc | Altitude +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Altitude (cont'd) |Ver| Res |Datum|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code: DHCP Option Code TBD (16 bits).
Polk, et al. Standards Track [Page 6]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
OptLen: Option Length. For version 1, the option length is 16.
LatUnc: 6 bits. When the Ver field = 1, this field represents
latitude uncertainty. The contents of this field is
undefined for other values of the Ver field.
Latitude: a 34 bit fixed point value consisting of 9 bits of
integer and 25 bits of fraction, interpreted as
described in Section 2.3.
LongUnc: 6 bits. When the Ver field = 1, this field represents
longitude uncertainty. The contents of this field is
undefined for other values of the Ver field.
Longitude: a 34 bit fixed point value consisting of 9 bits of
integer and 25 bits of fraction, interpreted as
described in Section 2.3.
AType: Altitude Type (4 bits), defined in Section 2.4.
AltUnc: 6 bits. When the Ver field = 1, this field represents
altitude uncertainty. The contents of this field is
undefined for other values of the Ver field.
Altitude: A 30 bit value defined by the AType field, described in
Section 2.4.
Ver: The Ver field is two bits, providing for four potential
versions. This specification defines the behavior of
version 1. The Ver field is always located at the same
offset from the beginning of the option, regardless of
the version in use. DHCPv6 clients implementing this
specification MUST support receiving version 1
responses. DHCPv6 servers implementing this
specification MUST send version 1 responses.
Res: The Res field which is 3 bits, is reserved. These bits
have been used by [IEEE-802.11y], but are not defined
within this specification.
Datum: 3 bits. The Map Datum used for the coordinates given in
this Option.
Polk, et al. Standards Track [Page 7]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
2.2. DHCPv4 Options
2.2.1. DHCPv4 Option 123
The format of DHCPv4 Option 123 is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code 123 | Length | LaRes | Latitude +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Latitude (cont'd) | LoRes | +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Longitude |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| AType | AltRes | Altitude +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Alt.(cont'd) | Res |Datum|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code: 8 bits. The code for the DHCPv4 option (123).
Length: 8 bits. The length of the DHCPv4 option, in octets.
The option length is 16.
LaRes: 6 bits. This field represents latitude resolution.
Latitude: a 34 bit fixed point value consisting of 9 bits of
signed integer and 25 bits of fraction, interpreted
as described in Section 2.3.
LoRes: 6 bits. This field represents longitude resolution.
Longitude: a 34 bit fixed point value consisting of 9 bits of
signed integer and 25 bits of fraction, interpreted
as described in Section 2.3.
AType: Altitude Type (4 bits), defined in Section 2.4.
AltRes: 6 bits. This field represents altitude resolution.
Altitude: A 30 bit value defined by the AType field, described in
Section 2.4.
Res: The Res field which is 5 bits, is reserved. These bits
have been used by IEEE 802.11y [IEEE-802.11y], but are
not defined within this specification.
Polk, et al. Standards Track [Page 8]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Datum: 3 bits. The Map Datum used for the coordinates given in
this Option.
2.2.2. DHCPv4 Option TBD
The format of DHCPv4 option TBD is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code TBD | Length | LatUnc | Latitude +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Latitude (cont'd) | LongUnc | +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Longitude |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| AType | AltUnc | Altitude +
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Alt.(cont'd) |Ver| Res |Datum|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Code: 8 bits. The code for the DHCPv4 option (TBD).
Length: 8 bits. The length of the DHCPv4 option, in octets.
For version 1, the option length is 16.
LatUnc: 6 bits. When the Ver field = 1, this field represents
latitude uncertainty. The contents of this field is
undefined for other values of the Ver field.
Latitude: a 34 bit fixed point value consisting of 9 bits of
integer and 25 bits of fraction, interpreted as
described in Section 2.3.
LongUnc: 6 bits. When the Ver field = 1, this field represents
longitude uncertainty. The contents of this field is
undefined for other values of the Ver field.
Longitude: a 34 bit fixed point value consisting of 9 bits of
integer and 25 bits of fraction, interpreted as
described in Section 2.3.
AType: Altitude Type (4 bits), defined in Section 2.4.
AltUnc: 6 bits. When the Ver field = 1, this field represents
altitude uncertainty. The contents of this field is
undefined for other values of the Ver field.
Polk, et al. Standards Track [Page 9]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Altitude: A 30 bit value defined by the AType field, described in
Section 2.4.
Ver: The Ver field is two bits, providing for four potential
versions. This specification defines the behavior of
version 1. The Ver field is always located at the same
offset from the beginning of the option, regardless of
the version in use.
Res: The Res field which is 3 bits, is reserved. These bits
have been used by [IEEE-802.11y], but are not defined
within this specification.
Datum: 3 bits. The Map Datum used for the coordinates given in
this Option.
2.2.3. Option Support
2.2.3.1. Client Support
DHCPv4 clients implementing this specification MUST support receiving
DHCPv4 Option TBD (version 1), and MAY support receiving DHCPv4
Option 123 (originally defined in RFC 3825 [RFC3825]).
DHCPv4 clients request the DHCPv4 server to send Option 123, Option
TBD or both via inclusion of the Parameter Request List option. As
noted in Section 9.8 of RFC 2132 [RFC2132]:
This option is used by a DHCP client to request values for
specified configuration parameters. The list of requested
parameters is specified as n octets, where each octet is a valid
DHCP option code as defined in this document.
The client MAY list the options in order of preference. The DHCP
server is not required to return the options in the requested
order, but MUST try to insert the requested options in the order
requested by the client.
When DHCPv4 and DHCPv6 clients implementing this specification do not
understand a datum value, they MUST assume a World Geodesic System
1984 (WGS84) [WGS84] datum (EPSG [EPSG] 4326 or 4979, depending on
whether there is an Altitude value present) and proceed accordingly.
Assuming that a less accurate location value is better than none,
this ensures that some (perhaps less accurate) location is available
to the client.
Polk, et al. Standards Track [Page 10]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
2.2.3.2. Server Option Selection
A DHCPv4 server implementing this specification MUST support sending
Option TBD version 1 and SHOULD support sending Option 123 in
responses.
A DHCPv4 server that provides location information SHOULD honor the
Parameter Request List included by the DHCPv4 client in order to
decide whether to send Option 123, Option TBD or both in the
Response.
2.3. Latitude and Longitude Fields
The Latitude and Longitude values in this specification are encoded
as 34 bit, twos complement, fixed point values with 9 integer bits
and 25 fractional bits. The exact meaning of these values is
determined by the datum; the description in this section applies to
the datums defined in this document. This document uses the same
definition for all datums it specifies.
When encoding, Latitude and Longitude values are rounded to the
nearest 34-bit binary representation. This imprecision is considered
acceptable for the purposes to which this form is intended to be
applied and is ignored when decoding.
Positive latitudes are north of the equator and negative latitudes
are south of the equator. Positive longitudes are east of the Prime
Meridian (Greenwich) and negative (2s complement) longitudes are west
of the Prime Meridian.
Within the coordinate reference systems defined in this document
(Datum values 1-3), longitude values outside the range of -180 to 180
decimal degrees or latitude values outside the range of -90 to 90
degrees MUST be considered invalid. Server implementations SHOULD
prevent the entry of invalid values within the selected coordinate
reference system. Location consumers MUST ignore invalid location
coordinates and SHOULD log invalid location errors.
2.3.1. Latitude and Longitude Resolution
The Latitude (LaRes), Longitude (LoRes) and Altitude (AltRes)
Resolution fields are encoded as 6 bit, unsigned integer values. In
the DHCPv4 Option 123, the LaRes, LoRes and AltRes fields are used to
encode the number of bits of resolution. The resolution sub-fields
accommodate the desire to easily adjust the precision of a reported
location. Contents beyond the claimed resolution MAY be randomized
to obscure greater precision that might be available.
Polk, et al. Standards Track [Page 11]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
In the DHCPv4 Option 123, the LaRes value encodes the number of high-
order latitude bits that should be considered valid. Any bits
entered to the right of this limit should not be considered valid and
might be purposely false, or zeroed by the sender. The examples in
Appendix B illustrate that a smaller value in the resolution field
increases the area within which the device is located. A value of 2
in the LaRes field indicates a precision of no greater than 1/6th
that of the globe (see the first example of Appendix B). A value of
34 in the LaRes field indicates a precision of about 3.11 mm in
latitude at the equator.
In the DHCPv4 Option 123, the LoRes value encodes the number of high-
order longitude bits that should be considered valid. Any bits
entered to the right of this limit should not be considered valid and
might be purposely false, or zeroed by the sender. A value of 2 in
the LoRes field indicates precision of no greater than 1/6th that of
the globe (see the first example of Appendix B). A value of 34 in
the LoRes field indicates a precision of about 2.42 mm in Longitude
(at the equator). Because lines of longitude converge at the poles,
the distance is smaller (better precision) for locations away from
the equator.
2.3.2. Latitude and Longitude Uncertainty
In the DHCPv6 option and the DHCPv4 Option TBD, the Latitude and
Longitude Uncertainty fields (LatUnc and LongUnc) quantify the amount
of uncertainty in each of the Latitude and Longitude values
respectively. A value of 0 is reserved to indicate that the
uncertainty is unknown; values greater than 34 are reserved.
A point within the region of uncertainty is selected to be the
encoded point; the centroid of the region is often an appropriate
choice. The value for uncertainty is taken as the distance from the
selected point to the furthest extreme of the region of uncertainty
on that axis. This is demonstrated in the figure below, which shows
a two-dimensional polygon that is projected on each axis. In the
figure, "X" marks the point that is selected; the ranges marked with
"U" is the uncertainty.
Polk, et al. Standards Track [Page 12]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
___ ___________
^ | / |
| | / |
| | / |
U | / |
| | ( |
V | | |
--X | X |
| | `---------.
| | |
| | |
| | |
- `-------------------------'
|---------X---------------|
|<------U------>|
Key
---
V, ^ = vertical arrows, delimiting the vertical uncertainty range.
<> = horizontal arrows, delimiting the horizontal uncertainty
range.
Uncertainty applies to each axis independently.
The amount of uncertainty can be determined from the encoding by
taking 2 to the power of 8, less the encoded value. As is shown in
the following formula, where "x" is the encoded integer value:
uncertainty = 2 ^ ( 8 - x )
The result of this formula is expressed in degrees of latitude or
longitude. The uncertainty is added to the base latitude or
longitude value to determine the maximum value in the uncertainty
range; similarly, the uncertainty is subtracted from the base value
to determine the minimum value. Note that because lines of longitude
converge at the poles, the actual distance represented by this
uncertainty changes with the distance from the equator.
If the maximum or minimum latitude values derived from applying
uncertainty are outside the range of -90 to +90, these values are
trimmed to within this range. If the maximum or minimum longitude
values derived from applying uncertainty are outside the range of
-180 to +180, then these values are normalized to this range by
adding or subtracting 360 as necessary.
The encoded value is determined by subtracting the next highest whole
Polk, et al. Standards Track [Page 13]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
integer value for the base 2 logarithm of uncertainty from 8. As is
shown by the following formula, where uncertainty is the midpoint of
the known range less the lower bound of that range:
x = 8 - ceil( log2( uncertainty ) )
Note that the result of encoding this value increases the range of
uncertainty to the next available power of two; subsequent repeated
encodings and decodings do not change the value. Only increasing
uncertainty means that the associated confidence does not have to
decrease.
2.4. Altitude
How the Altitude value is interpreted depends on the Altitude Type
(AType) value and the selected datum. Three Altitude Type values are
defined in this document: unknown (0), meters (1) and floors (2).
2.4.1. No Known Altitude (AType = 0)
In some cases, the altitude of the location might not be provided.
An Altitude Type value of zero indicates that the altitude is not
given to the client. In this case, the Altitude and Altitude
Uncertainty fields can contain any value and MUST be ignored.
2.4.2. Altitude in Meters (AType = 1)
If the Altitude Type has a value of one, Altitude is measured in
meters, in relation to the zero set by the vertical datum. For AType
= 1, the Altitude value is expressed as a 30 bit, fixed point, twos
complement integer with 22 integer bits and 8 fractional bits.
2.4.3. Altitude in Floors (AType = 2)
A value of two for Altitude Type indicates that the Altitude value is
measured in floors. Since altitude in meters may not be known within
a building, a floor indication may be more useful. For AType = 2,
the Altitude value is expressed as a 30 bit, fixed point, twos
complement integer with 22 integer bits and 8 fractional bits.
This value is relevant only in relation to a building; the value is
relative to the ground level of the building. Floors located below
ground level are represented by negative values. In some buildings
it might not be clear which floor is at ground level or an
intermediate floor might be hard to identify as such. Determining
what floor is at ground level and what constitutes a sub-floor as
opposed to an naturally numbered floor is left to local
interpretation.
Polk, et al. Standards Track [Page 14]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Larger values represent floors that are farther away from floor 0
such that:
- if positive, the floor value is farther above the ground floor.
- if negative, the floor value is farther below the ground floor.
Non-integer values can be used to represent intermediate or sub-
floors, such as mezzanine levels. Example: a mezzanine between floor
1 and floor 2 could be represented as a value of 1.25. Example:
mezzanines between floor 4 and floor 5 could be represented as values
of 4.5 and 4.75.
2.4.4. Altitude Resolution
In the DHCPv4 Option 123, the Altitude Resolution (AltRes) value
encodes the number of high-order altitude bits that should be
considered valid. Values above 30 (decimal) are undefined and
reserved.
If the Altitude Type value is one (AType = 1), an AltRes value 0.0
would indicate unknown Altitude. The most precise altitude would
have an AltRes value of 30. Many values of AltRes would obscure any
variation due to vertical datum differences.
The AltRes field SHOULD be set to maximum precision when AType = 2
(floors) when a floor value is included in the DHCP Reply, or when
AType = 0, to denote that the floor isn't known. An altitude coded
as AType = 2, AltRes = 30, and Altitude = 0.0 is meaningful even
outside a building, and represents ground level at the given latitude
and longitude.
2.4.5. Altitude Uncertainty
In the DHCPv6 option or the DHCPv4 Option TBD, the AltUnc value
quantifies the amount of uncertainty in the Altitude value. As with
LatUnc and LongUnc, a value of 0 for AltUnc is reserved to indicate
that Altitude Uncertainty is not known; values above 30 are also
reserved. Altitude Uncertainty only applies to Altitude Type 1.
The amount of Altitude Uncertainty can be determined by the following
formula, where x is the encoded integer value:
Uncertainty = 2 ^ ( 21 - x )
This value uses the same units as the associated altitude.
Similarly, a value for the encoded integer value can be derived by
the following formula:
Polk, et al. Standards Track [Page 15]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
x = 21 - ceil( log2( uncertainty ) )
2.5. Datum
The Datum field determines how coordinates are organized and related
to the real world. Three datums are defined in this document, based
on the definitions in [OGP.Geodesy]:
1: WGS84 (Latitude, Longitude, Altitude):
The World Geodesic System 1984 [WGS84] coordinate reference
system.
This datum is identified by the European Petroleum Survey Group
(EPSG)/International Association of Oil & Gas Producers (OGP) with
the code 4979, or by the URN "urn:ogc:def:crs:EPSG::4979".
Without Altitude, this datum is identified by the EPSG/OGP code
4326 and the URN "urn:ogc:def:crs:EPSG::4326".
2: NAD83 (Latitude, Longitude) + NAVD88:
This datum uses a combination of the North American Datum 1983
(NAD83) for horizontal (Latitude and Longitude) values, plus the
North American Vertical Datum of 1988 (NAVD88) vertical datum.
This datum is used for referencing location on land (not near
tidal water) within North America.
NAD83 is identified by the EPSG/OGP code of 4269, or the URN
"urn:ogc:def:crs:EPSG::4269". NAVD88 is identified by the EPSG/
OGP code of 5703, or the URN "urn:ogc:def:crs:EPSG::5703".
3: NAD83 (Latitude, Longitude) + MLLW:
This datum uses a combination of the North American Datum 1983
(NAD83) for horizontal (Latitude and Longitude) values, plus the
Mean Lower Low Water (MLLW) vertical datum.
This datum is used for referencing location on or near tidal water
within North America.
NAD83 is identified by the EPSG/OGP code of 4269, or the URN
"urn:ogc:def:crs:EPSG::4269". MLLW does not have a specific code
or URN.
All hosts MUST support the WGS84 datum (Datum 1).
3. Security Considerations
Geopriv requirements (including security requirements) are discussed
in "Geopriv Requirements" [RFC3693]. A threat analysis is provided
Polk, et al. Standards Track [Page 16]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
in "Threat Analysis of the Geopriv Protocol" [RFC3694].
Since there is no privacy protection for DHCP messages, an
eavesdropper who can monitor the link between the DHCP server and
requesting client can discover this LCI.
To minimize the unintended exposure of location information, the LCI
option SHOULD be returned by DHCP servers only when the DHCP client
has included this option in its 'parameter request list' (Section 3.5
[RFC2131], Section 9.8 [RFC2132]).
Where critical decisions might be based on the value of this option,
DHCP authentication as defined in "Authentication for DHCP Messages"
[RFC3118] and "Dynamic Host Configuration Protocol for IPv6 (DHCPv6)"
[RFC3315] SHOULD be used to protect the integrity of the DHCP
options.
Link layer confidentiality and integrity protection may also be
employed to reduce the risk of location disclosure and tampering.
4. IANA Considerations
IANA has assigned a DHCPv4 option code of 123 for the GeoConf option.
Assignment of an additional DHCPv4 option code as well as a DHCPv6
option code is requested.
IANA maintains registries for the Altitude Type (AType), Datum and
Version fields. New values for each of these registries are assigned
through "Standards Actions" [RFC5226].
Each AType registry entry MUST define the way that the 30 bit
altitude values and the associated 6 bit uncertainty are interpreted.
Each Datum registry entry MUST include specification of both
horizontal and vertical datum, and MUST define the way that the 34
bit values and the respective 6 bit uncertainties are interpreted.
The initial AType registry is:
AType = 0 No known altitude.
AType = 1 meters of altitude defined by the vertical datum
specified.
AType = 2 building floors of altitude.
The initial Datum registry is:
Polk, et al. Standards Track [Page 17]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Datum = 1 denotes the vertical datum WGS 84 as defined by the EPSG
as their CRS Code 4327; CRS Code 4327 also specifies WGS 84
as the vertical datum.
Datum = 2 denotes the vertical datum NAD83 as defined by the EPSG as
their CRS Code 4269; North American Vertical Datum of 1988
(NAVD88) is the associated vertical datum for NAD83.
Datum = 3 denotes the vertical datum NAD83 as defined by the EPSG as
their CRS Code 4269; Mean Lower Low Water (MLLW) is the
associated vertical datum for NAD83.
The initial Version registry is:
1: Implementations utilizing uncertainty parameters
(for both DHCPv4 and DHCPv6).
5. Acknowledgments
The authors would like to thank Randall Gellens, Patrik Falstrom,
Ralph Droms, Ted Hardie, Jon Peterson, Robert Sparks, Ralph Droms and
Nadine Abbott for their inputs and constructive comments regarding
this document. Additionally, the authors would like to thank Greg
Troxel for the education on vertical datums, as well as Carl Reed.
Thanks to Richard Barnes for his contribution on GML mapping for
resolution.
6. References
6.1. Normative References
[EPSG] European Petroleum Survey Group, http://www.epsg.org/ and
http://www.epsg-registry.org/
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2131] Droms, R., "Dynamic Host Configuration Protocol", RFC 2131,
March 1997.
[RFC2132] Alexander, S. and R. Droms, "DHCP Options and BOOTP Vendor
Extensions", RFC2132, March 1997.
[RFC3046] Patrick, M., "DHCP Relay Agent Information Option", RFC
3046, January 2001.
[RFC3118] Droms, R. and W. Arbaugh, "Authentication for DHCP
Messages", RFC 3118, June 2001.
Polk, et al. Standards Track [Page 18]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C. and
M. Carney, "Dynamic Host Configuration Protocol for IPv6
(DHCPv6)", RFC 3315, July 2003.
[WGS84] US National Imagery and Mapping Agency, "Department of
Defense (DoD) World Geodetic System 1984 (WGS 84), Third
Edition", NIMA TR8350.2, January 2000,
https://www1.nga.mil/PRODUCTSSERVICES/GEODESYGEOPHYSICS/
WORLDGEODETICSYSTEM/Pages/default.aspx and
http://www.ngs.noaa.gov/faq.shtml#WGS84
6.2. Informational References
[Convey] Polk, J., Rosen, B. and J. Peterson, "Location Conveyance
for the Session Initiation Protocol", Internet draft (work
in progress), draft-ietf-sipcore-location-
conveyance-04.txt, October 25, 2010.
[GeoShape] Thomson, M. and C. Reed, "GML 3.1.1 PIDF-LO Shape
Application Schema for use by the Internet Engineering Task
Force (IETF)", Candidate OpenGIS Implementation
Specification 06-142, Version: 0.0.9, December 2006.
[IEEE-802.11y]
Information technology - Telecommunications and information
exchange between systems - Local and metropolitan area
networks - Specific requirements - Part 11: Wireless LAN
Medium Access Control (MAC) and Physical Layer (PHY)
specifications Amendment 3: 3650-3700 MHz Operation in USA,
November 2008.
[NENA] National Emergency Number Association (NENA) www.nena.org
NENA Technical Information Document on Model Legislation
Enhanced 911 for Multi-Line Telephone Systems.
[RFC3046] Patrick, M., "DHCP Relay Agent Information Option", RFC
3046, January 2001.
[RFC3693] Cuellar, J., Morris, J., Mulligan, D., Peterson, J. and J.
Polk, "Geopriv Requirements", RFC 3693, February 2004.
[RFC3694] Danley, M., Mulligan, D., Morris, J. and J. Peterson,
"Threat Analysis of the Geopriv Protocol", RFC 3694,
February 2004.
[RFC3825] Polk, J., Schnizlein, J. and M. Linsner, "Dynamic Host
Configuration Protocol Option for Coordinate-based Location
Configuration Information", RFC 3825, July 2004.
Polk, et al. Standards Track [Page 19]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
[RFC4119] Peterson, J., "A Presence-based GEOPRIV Location Object
Format", RFC 4119, December 2005.
[RFC4776] Schulzrinne, H., "Dynamic Host Configuration Protocol
(DHCPv4 and DHCPv6) Option for Civic Addresses
Configuration Information", RFC 4776, November 2006.
[RFC5139] Thomson, M. and J. Winterbottom, "Revised Civic Location
Format for Presence Information Data Format Location Object
(PIDF-LO)", RFC 5139, February 2008.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", RFC 5226, May 2008.
[RFC5491] Winterbottom, J., Thomson, M. and H. Tschofenig, "GEOPRIV
PIDF-LO Usage Clarification, Considerations, and
Recommendations ", RFC 5491, March 2009
Polk, et al. Standards Track [Page 20]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Appendix A. GML Mapping
The GML representation of a decoded DHCP option depends on what
fields are specified. The DHCP format for location logically
describes a geodetic prism, rectangle, or point, depending on whether
Altitude and uncertainty values are provided. In the absence of
uncertainty information, the value decoded from the DHCP form can be
expressed as a single point; this is true regardless of whether the
version 0 or version 1 interpretations of the uncertainty fields are
used. If the point includes Altitude, it uses a three dimensional
CRS, otherwise it uses a two dimensional CRS. If all fields are
included along with uncertainty, the shape described is a rectangular
prism. Note that this is necessary given that uncertainty for each
axis is provided independently.
If Altitude or Altitude Uncertainty (AltUnc) is not specified, the
shape is described as a rectangle using the "gml:Polygon" shape. If
Altitude is available, a three dimensional CRS is used, otherwise a
two dimensional CRS is used.
For Datum values of 2 or 3 (NAD83), there is no available CRS URN
that covers three dimensional coordinates. By necessity, locations
described in these datums can be represented by two dimensional
shapes only; that is, either a two dimensional point or a polygon.
If the Altitude Type is 2 (floors), then this value can be
represented using a civic address object [RFC5139] that is presented
alongside the geodetic object.
This Appendix describes how the location value encoded in DHCP format
for geodetic location can be expressed in GML. The mapping is valid
for the DHCPv6 option as well as both of the DHCPv4 options, and for
the currently-defined datum values (1, 2, and 3). Further version or
datum definitions should provide similar mappings.
These shapes can be mapped to GML by first computing the bounds that
are described using the coordinate and uncertainty fields, then
encoding the result in a GML Polygon or Prism shape.
A.1. GML Templates
If Altitude is provided in meters (AType 1) and the datum value is
WGS84 (value 1), then the proper GML shape is a Prism, with the
following form (where $value$ indicates a value computed from the
DHCP option as described below):
$lowLatitude$ $lowLongitude$ $lowAltitude$
$lowLatitude$ $highLongitude$ $lowAltitude$
$highLatitude$ $highLongitude$ $lowAltitude$
$highLatitude$ $lowLongitude$ $lowAltitude$
$lowLatitude$ $lowLongitude$ $lowAltitude$
$highAltitude - lowAltitude$
The Polygon shape is used if Altitude is omitted or specified in
floors, or if either NAD83 datum is used (value 2 or 3). The
corresponding GML Polygon has the following form:
>
$lowLatitude$ $lowLongitude$
$lowLatitude$ $highLongitude$
$highLatitude$ $highLongitude$
$highLatitude$ $lowLongitude$
$lowLatitude$ $lowLongitude$
The value "2D-CRS-URN" is defined by the datum value: If the datum is
WGS84 (value 1), then the 2D-CRS-URN is "urn:ogc:def:crs:EPSG::4326".
If the datum is NAD83 (value 2 or 3), then the 2D-CRS-URN is
"urn:ogc:def:crs:EPSG::4269".
A Polygon shape with the WGS84 three-dimensional CRS is used if the
datum is WGS84 (value 1) and the Altitude is specified in meters
(Altitude type 1), but no Altitude uncertainty is specified (that is,
Polk, et al. Standards Track [Page 22]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
AltUnc is 0). In this case, the value of the Altitude field is added
after each of the points above, and the srsName attribute is set to
the three-dimensional WGS84 CRS, namely "urn:ogc:def:crs:EPSG::4979".
A simple point shape is used if either Latitude uncertainty (LatUnc)
or Longitude uncertainty (LongUnc) is not specified. With Altitude,
this uses a three-dimensional CRS; otherwise, it uses a two-
dimensional CRS.
$Latitude$ $Longitude$ $[Altitude]$
A.1.1. Finding Low and High Values using Uncertainty Fields
For the DHCPv4 Option 123, resolution fields are used (LaRes, LoRes,
AltRes), indicating how many bits of a value contain information.
Any bits beyond those indicated can be either zero or one.
For the DHCPv6 option and DHCPv4 Option TBD, the LatUnc, LongUnc and
AltUnc fields indicate uncertainty distances, denoting the bounds of
the location region described by the DHCP location object.
The two sections below describe how to compute the Latitude,
Longitude, and Altitude bounds (e.g., $lowLatitude$, $highAltitude$)
in the templates above. The first section describes how these bounds
are computed in the "resolution encoding" (DHCPv4 Option 123), while
the second section addresses the "uncertainty encoding" (DHCPv6
Option and DHCPv4 Option TBD).
A.1.1.1. Resolution Encoding
Given a number of resolution bits (i.e., the value of a resolution
field), if all bits beyond those bits are set to zero, this gives the
lowest possible value. The highest possible value can be found
setting all bits to one.
If the encoded value of Latitude/Longitude and resolution (LaRes,
LoRes) are treated as 34-bit unsigned integers, the following can be
used (where ">>" is a bitwise right shift, "&" is a bitwise AND, "~"
is a bitwise negation, and "|" is a bitwise OR).
mask = 0x3ffffffff >> resolution
lowvalue = value & ~mask
highvalue = value | mask + 1
Once these values are determined, the corresponding floating point
Polk, et al. Standards Track [Page 23]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
numbers can be computed by dividing the values by 2^25 (since there
are 25 bits of fraction in the fixed-point representation).
Alternatively, the lowest possible value can be found by using
resolution to determine the size of the range. This method has the
advantage that it operates on the decoded floating point values. It
is equivalent to the first mechanism, to a possible error of 2^-25
(2^-8 for altitude).
scale = 2 ^ ( 9 - resolution )
lowvalue = floor( value / scale ) * scale
highvalue = lowvalue + scale
Altitude resolution (AltRes) uses the same process with different
constants. There are 22 whole bits in the Altitude encoding (instead
of 9) and 30 bits in total (instead of 34).
A.1.1.2. Uncertainty Encoding
In the uncertainty encoding, the uncertainty fields (LongUnc/LatUnc)
directly represent the logarithms of uncertainty distances. So the
low and high bounds are computed by first computing the uncertainty
distances, then adding and subtracting these from the value provided.
If "uncertainty" is the unsigned integer value of the uncertainty
field and "value" is the value of the coordinate field:
distance = 2 ^ (8 - uncertainty)
lowvalue = value - distance
highvalue = value + distance
Altitude uncertainty (AltUnc in version 1) uses the same process with
different constants:
distance = 2 ^ (21 - uncertainty)
lowvalue = value - distance
Appendix B. Calculations of Resolution
The following examples for two different locations demonstrate how
the Resolution values for Latitude, Longitude, and Altitude (used in
DHCPv4 Option 123) can be calculated. In both examples, the geo-
location values were derived from maps using the WGS84 map datum,
therefore in these examples, the Datum field would have a value = 1
(00000001, or 0x01).
Polk, et al. Standards Track [Page 24]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
B.1. Location Configuration Information of "White House" (Example 1)
The grounds of the White House in Washington D.C. (1600 Pennsylvania
Ave. NW, Washington, DC 20006) can be found between 38.895375 and
38.898653 degrees North and 77.037911 and 77.035116 degrees West. In
this example, we assume that we are standing on the sidewalk on the
north side of the White House, between driveways. Since we are not
inside a structure, we assume an Altitude value of 15 meters,
interpolated from the US Geological survey map, Washington Washington
West quadrangle.
The address was NOT picked for any political reason and can easily be
found on the Internet or mapping software, but was picked as an
easily identifiable location on our planet.
In this example, the requirement of emergency responders in North
America via their NENA Model Legislation [NENA] could be met by a
LaRes value of 21 and a LoRes value of 20. This would yield a geo-
location that is Latitude 38.8984375 north to Latitude 38.8988616
north and Longitude -77.0371094 to Longitude -77.0375977. This is an
area of approximately 89 feet by 75 feet or 6669 square feet, which
is very close to the 7000 square feet requested by NENA. In this
example, a service provider could enforce that a device send a
Location Configuration Information with this minimum amount of
resolution for this particular location when calling emergency
services.
An approximate representation of this location might be provided using
the DHCPv4 Option 123 encoding as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code (123) | OptLen (16) | LaRes | Latitude .
|0 1 1 1 1 0 1 1|0 0 0 1 0 0 0 0|0 1 0 0 1 0|0 0 0 1 0 0 1 1 0 1.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. Latitude (cont'd) | LoRes | .
.1 1 0 0 1 0 1 1 1 0 0 1 1 0 0 0 0 1 1 0 0 0 1 1|0 1 0 0 0 1|1 1.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. Longitude (cont'd) |
.0 1 1 0 0 1 0 1 1 1 1 0 1 1 0 1 0 1 0 0 0 0 1 0 1 1 0 0 0 1 0 0|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| AType | AltRes | Altitude .
|0 0 0 1|0 1 0 0 0 1|0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. Alt (cont'd) | Res |Datum|
.0 0 0 0 0 0 0 0|0 0 0 0 0|0 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Polk, et al. Standards Track [Page 25]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
In hexadecimal, this is 7B10484D CB986347 65ED42C4 1440000F 0001.
Decoding Location Configuration Information with Resolution
Decoding this option gives a latitude of 38.897647 (to 7 decimal
places) with 18 bits of resolution; a longitude of -77.0366000 with
17 bits of resolution; an altitude type of meters with a value of 15
and 17 bits of resolution; version 0 (resolution) and the WGS84
datum.
For the latitude value, 18 bits of resolution allow for values in the
range from 38.8964844 to 38.8984375. For the longitude value, 17
bits of resolution allow for values in the range from -77.0390625 to
-77.0351563. Having 17 bits of resolution in the altitude allows for
values in the range from 0 to 32 meters.
GML Representation of Decoded Location Configuration Information
The following GML shows the value decoded in the previous example as
a point in a three dimensional CRS:
38.897647 -77.0366 15
This representation ignores the values included in the resolution
parameters. If resolution values are provided, a rectangular prism
can be used to represent the location.
The following example uses all of the decoded information from the
previous example:
38.8964844 -77.0390625 0
38.8964844 -77.0351563 0
38.8984375 -77.0351563 0
38.8984375 -77.0390625 0
38.8964844 -77.0390625 0
Polk, et al. Standards Track [Page 26]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
32
B.2. Location Configuration Information of "Sears Tower" (Example 2)
Postal Address:
Sears Tower
103rd Floor
233 S. Wacker Dr.
Chicago, IL 60606
Viewing the Chicago area from the Observation Deck of the Sears
Tower.
Latitude 41.87884 degrees North (or +41.87884 degrees)
Using 2s complement, 34 bit fixed point, 25 bit fraction
Latitude = 0x053c1f751,
Latitude = 0001010011110000011111011101010001
Longitude 87.63602 degrees West (or -87.63602 degrees)
Using 2s complement, 34 bit fixed point, 25 bit fraction
Longitude = 0xf50ba5b97,
Longitude = 1101010000101110100101101110010111
Altitude 103
In this example, we are inside a structure, therefore we will assume
an Altitude value of 103 to indicate the floor we are on. The
Altitude Type value is 2, indicating floors. The AltRes field would
indicate that all bits in the Altitude field are true, as we want to
accurately represent the floor of the structure where we are located.
AltRes = 30, 0x1e, 011110
AType = 2, 0x02, 000010
Altitude = 103, 0x00006700, 000000000000000110011100000000
For the accuracy of the Latitude and Longitude, the best information
available to us was supplied by a generic mapping service that shows
a single geo-loc for all of the Sears Tower. Therefore we are going
to show LaRes as value 18 (0x12 or 010010) and LoRes as value 18
(0x12 or 010010). This would be describing a geo-location area that
is Latitude 41.8769531 to Latitude 41.8789062 and extends from
-87.6367188 degrees to -87.6347657 degrees Longitude. This is an
area of approximately 373412 square feet (713.3 ft. x 523.5 ft.).
Polk, et al. Standards Track [Page 27]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Appendix C. Calculations of Uncertainty
The following example demonstrates how uncertainty values for
Latitude, Longitude, and Altitude (LatUnc, LongUnc and AltUnc
used in the DHCPv6 option as well as DHCPv4 Option TBD)
can be calculated.
C.1. Location Configuration Information of "Sydney Opera House"
(Example 3)
This section describes an example of encoding and decoding the
geodetic DHCP Option. The textual results are expressed in GML
[OGC.GML-3.1.1] form, suitable for inclusion in PIDF-LO [RFC4119].
These examples all assume a datum of WGS84 (datum = 1) and an
Altitude type of meters (AType = 1).
C.1.1. Encoding a Location into DHCP Geodetic Form
This example draws a rough polygon around the Sydney Opera House.
This polygon consists of the following six points:
33.856625 S, 151.215906 E
33.856299 S, 151.215343 E
33.856326 S, 151.214731 E
33.857533 S, 151.214495 E
33.857720 S, 151.214613 E
33.857369 S, 151.215375 E
The top of the building 67.4 meters above sea level, and a starting
Altitude of 0 meters above the WGS84 geoid is assumed.
The first step is to determine the range of Latitude and Longitude
values. Latitude ranges from -33.857720 to -33.856299; Longitude
ranges from 151.214495 to 151.215906.
For this example, the point that is encoded is chosen by finding the
middle of each range, that is (-33.8570095, 151.2152005). This is
encoded as (1110111100010010010011011000001101,
0100101110011011100010111011000011) in binary, or (3BC49360D,
12E6E2EC3) in hexadecimal notation (with an extra 2 bits of leading
padding on each). Altitude is set at 33.7 meters, which is
000000000000000010000110110011 (binary) or 000021B3 (hexadecimal).
The Latitude Uncertainty (LatUnc) is given by inserting the
difference between the center value and the outer value into the
formula from Section 2.3.1. This gives:
Polk, et al. Standards Track [Page 28]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
x = 8 - ceil( log2( -33.8570095 - -33.857720 ) )
The result of this equation is 18, therefore the uncertainty is
encoded as 010010 in binary.
Similarly, Longitude Uncertainty (LongUnc) is given by the formula:
x = 8 - ceil( log2( 151.2152005 - 151.214495 ) )
The result of this equation is also 18, or 010010 in binary.
Altitude Uncertainty (AltUnc) uses the formula from Section 2.4.4:
x = 21 - ceil( log2( 33.7 - 0 ) )
The result of this equation is 15, which is encoded as 001111 in
binary.
Adding an Altitude Type of 1 (meters) and a Datum of 1 (WGS84), this
gives the following DHCPv4 Option TBD form:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Code (TBD) | OptLen (16) | LatUnc | Latitude .
|0 1 1 1 1 0 1 1|0 0 0 1 0 0 0 0|0 1 0 0 1 0|1 1 1 0 1 1 1 1 0 0.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. Latitude (cont'd) | LongUnc | .
.0 1 0 0 1 0 0 1 0 0 1 1 0 1 1 0 0 0 0 0 1 1 0 1|0 1 0 0 1 0|0 1.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. Longitude (cont'd) |
.0 0 1 0 1 1 1 0 0 1 1 0 1 1 1 0 0 0 1 0 1 1 1 0 1 1 0 0 0 0 1 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| AType | AltUnc | Altitude .
|0 0 0 1|0 0 1 1 1 1|0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
. Alt (cont'd) |Ver| Res |Datum|
.1 0 1 1 0 0 1 1|0 1|0 0 0|0 0 1|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In hexadecimal, this is 7B104BBC 49360D49 2E6E2EC3 13C00021 B341.
The DHCPv6 form only differs in the code and option length portion.
C.1.2. Decoding a Location from DHCP Geodetic Form
If receiving the binary form created in the previous section, this
section describes how that would be interpreted. The result is then
represented as a GML object, as defined in [GeoShape].
Polk, et al. Standards Track [Page 29]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
A Latitude value of 1110111100010010010011011000001101 decodes to a
value of -33.8570095003 (to 10 decimal places). The Longitude value
of 0100101110011011100010111011000011 decodes to 151.2152005136.
Decoding Tip: If the raw values of Latitude and Longitude are placed
in integer variables, the actual value can be derived by the
following process:
1. If the highest order bit is set (i.e. the number is a twos
complement negative), then subtract 2 to the power of 34 (the
total number of bits).
2. Divide the result by 2 to the power of 25 (the number of
fractional bits) to determine the final value.
The same principle can be applied when decoding Altitude values,
except with different powers of 2 (30 and 8 respectively).
The Latitude and Longitude Uncertainty are both 18, which gives an
uncertainty value using the formula from Section 2.3.1 of
0.0009765625. Therefore, the decoded Latitudes is -33.8570095003 +/-
0.0009765625 (or the range from -33.8579860628 to -33.8560329378) and
the decoded Longitude is 151.2152005136 +/- 0.0009765625 (or the
range from 151.2142239511 to 151.2161770761).
The encoded Altitude of 000000000000000010000110110011 decodes to
33.69921875. The encoded uncertainty of 15 gives a value of 64,
therefore the final uncertainty is 33.69921875 +/- 64 (or the range
from -30.30078125 to 97.69921875).
C.1.2.1. GML Representation of Decoded Locations
The following GML shows the value decoded in the previous example as
a point in a three dimensional CRS:
-33.8570095003 151.2152005136 33.69921875
The following example uses all of the decoded information from the
previous example:
Polk, et al. Standards Track [Page 30]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
-33.8579860628 151.2142239511 -30.30078125
-33.8579860628 151.2161770761 -30.30078125
-33.8560329378 151.2161770761 -30.30078125
-33.8560329378 151.2142239511 -30.30078125
-33.8579860628 151.2142239511 -30.30078125
128
Note that this representation is only appropriate if the uncertainty
is sufficiently small. [GeoShape] recommends that distances between
polygon vertices be kept short. A GML representation like this one
is only appropriate where uncertainty is less than 1 degree (an
encoded value of 9 or greater).
Polk, et al. Standards Track [Page 31]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Appendix D. Changes from RFC 3825
This section lists the major changes between RFC 3825 and this
document. Minor changes, including style, grammar, spelling and
editorial changes are not mentioned here.
o Section 1 now includes clarifications on wired and wireless uses.
o The former Sections 1.2 and 1.3 have been removed. Section 1.2
now defines the concepts of uncertainty and resolution, as well
as conversion between the DHCP option format and PIDF-LO.
o A DHCPv6 option is now defined (Section 2.1) as well
as DHCPv4 options (Section 2.2).
o The former Datum field has been split into three fields:
Ver, Res and Datum. These fields are used in both the
DHCPv4 and DHCPv6 options.
o Section 2.2.3 has been added, describing option support.
o Section 2.3 has been added, describing the Latitude and
Longitude fields.
o Section 2.3.1 has been added, covering Latitude and Longitude
resolution.
o Section 2.3.2 has been added, covering Latitude and Longitude
uncertainty.
o Section 2.4 has been added, covering values of the Altitude
field (Sections 2.4.1, 2.4.2 and 2.4.3), Altitude resolution
(Section 2.4.4), and Altitude uncertainty (Section 2.4.5).
o Section 2.5 has been added, covering the Datum field.
o Section 3 (Security Considerations) has added a recommendation
on link layer confidentiality.
o Section 4 (IANA Considerations) has consolidated material
relating to parameter allocation for both the DHCPv4 and
DHCPv6 option parameters.
o The material formerly in Appendix A has been updated and
shortened and has been moved to Appendix B.
o An Appendix A on GML mapping has been added.
o Appendix C has been added, providing an example of uncertainty
encoding.
o Appendix D has been added, detailing the changes from RFC 3825.
Polk, et al. Standards Track [Page 32]
INTERNET-DRAFT DHCP Options for Coordinate LCI 25 January 2011
Authors' Addresses
James M. Polk
Cisco Systems
2200 East President George Bush Turnpike
Richardson, Texas 75082 USA
USA
EMail: jmpolk@cisco.com
John Schnizlein
EMail: john@schnizlein.org
Marc Linsner
Cisco Systems
Marco Island, FL 34145 USA
USA
EMail: marc.linsner@cisco.com
Martin Thomson
Andrew
PO Box U40
Wollongong University Campus, NSW 2500
AU
EMail: martin.thomson@andrew.com
Bernard Aboba
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052 USA
USA
EMail: bernard_aboba@hotmail.com
Polk, et al. Standards Track [Page 33]