Network Working Group J. Quittek Internet-Draft R. Winter Intended status: Standards Track T. Dietz Expires: January 8, 2012 NEC Europe Ltd. July 7, 2011 Definition of Managed Objects for Battery Monitoring draft-ietf-eman-battery-mib-02 Abstract This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it defines managed objects that provide information on the status of batteries in managed devices. Status of this Memo This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79. Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at http://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." This Internet-Draft will expire on January 8, 2012. Copyright Notice Copyright (c) 2011 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Quittek, et al. Expires January 8, 2012 [Page 1] Internet-Draft Battery MIB July 2011 Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3 2. The Internet-Standard Management Framework . . . . . . . . . . 4 3. Structure of the Battery MIB Module . . . . . . . . . . . . . 4 4. Battery Technologies and Properties . . . . . . . . . . . . . 6 5. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 7 6. Security Considerations . . . . . . . . . . . . . . . . . . . 21 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 22 7.1. SMI Object Identifier Registration . . . . . . . . . . . . 22 7.2. Battery Technology Registration . . . . . . . . . . . . . 22 8. Open Issues . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.1. Writable Notification thresholds . . . . . . . . . . . . . 23 8.2. Re-arming batteryLowNotification . . . . . . . . . . . . . 23 8.3. Alignment with the Smart Battery Data Specification . . . 23 9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 23 10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 23 10.1. Normative References . . . . . . . . . . . . . . . . . . . 23 10.2. Informative References . . . . . . . . . . . . . . . . . . 24 Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 24 Quittek, et al. Expires January 8, 2012 [Page 2] Internet-Draft Battery MIB July 2011 1. Introduction Today, more and more managed devices contain batteries that supply them with power when disconnected from electrical power distribution grids. Common examples are nomadic and mobile devices, such as notebook computers, netbooks, and smart phones. The status of batteries in such a device, particularly the charging status is typically controlled by automatic functions that act locally on the device and manually by users of the device. In addition to this, there is a need to monitor battery status of these devices by network management systems. This document defines a portion of the Management Information Base (MIB) that provides means for monitoring batteries in or attached to managed devices. The Battery MIB module defined in Section 5 meets the requirements for monitoring the status of batteries specified in [I-D.ietf-eman-requirements]. The Battery MIB module serves for monitoring the battery status. It does not implement a Power Monitor as defined in the framework for energy management [I-D.ietf-eman-framework]. Amongst other things, the Battery MIB allows to monitor: o the current charge of a battery, o the age of a battery (charging cycles), o the state of a battery (e.g. being re-charged), o last usage of a battery, o maximum energy provided by a battery (remaining and total capacity). Further, means are provided for battery-powered devices to send notifications when the current battery charge has dropped below a certain threshold in order to inform the management system of needed replacement. The same applies to the age of a battery. There is already instrumentation for monitoring battery status on many battery-driven devices, because this is already needed for local control of the battery by the device. This reduces the effort for implementing the managed objects defined in this document. For many devices only additional software will be needed but no additional hardware instrumentation for battery monitoring. Since there are a lot of devices in use that contain more than one battery, means for battery monitoring defined in this document support addressing multiple batteries within a single device. Also, batteries today often come in packages that can include identification and might contain additional hardware and firmware. The former allows to trace a battery and allows continuous monitoring Quittek, et al. Expires January 8, 2012 [Page 3] Internet-Draft Battery MIB July 2011 even if the battery is e.g. installed in another device. The firmware version is useful information as the battery behavior might be different for different firmware versions. Not explicitly in scope of definitions in this document are very small backup batteries, such as for example, batteries used on PC motherboard to run the clock circuit and retain configuration memory while the system is turned off. Other means may be required for reporting on these batteries. However, the MIB module defined in Section 3 can be used for this purpose. A traditional type of managed device containing batteries is an Uninterruptible Power Supply (UPS) system; these supply other devices with electrical energy when the main power supply fails. There is already a MIB module for managing UPS systems defined in RFC 1628 [RFC1628]. This module includes managed objects for monitoring the batteries contained in an UPS system. However, the information provided by these objects is limited and tailored the particular needs of UPS systems. The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [RFC2119]. 2. The Internet-Standard Management Framework For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [RFC3410]. Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies MIB modules that are compliant to the SMIv2, which is described in STD 58, RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58,RFC 2580 [RFC2580]. 3. Structure of the Battery MIB Module The Battery MIB module defined in this document defines objects for reporting information about batteries. All managed objects providing information of the status of a battery are contained in a single table called batteryTable. The batteryTable contains one conceptual Quittek, et al. Expires January 8, 2012 [Page 4] Internet-Draft Battery MIB July 2011 row per battery. If there is an implementation of the Entity MIB module [RFC4133] that identifies the batteries to be reported on by individual values for managed object entPhysicalIndex, then it is REQUIRED that these values are used as index values for the batteryTable. The kind of entity in the entPhysicalTable of the Entity MIB module is indicated by the value of enumeration object entPhysicalClass. Since there is no value called 'battery' defined for this object, it is RECOMMENDED that for batteries the value of this object is chosen to be powerSupply(6). The batteryTable contains three groups of objects. The first group (OIDs ending with 2-10) provides information on static properties of the battery. The second group of objects (OIDs ending with 11-18) provides information on the current battery state, if it is charging or discharging, how much it is charged, its remaining capacity, the number of experienced charging cycles, etc. batteryTable(1) +--batteryEntry(1) [batteryIndex] +-- --- Integer32 batteryIndex(1) +-- r-n SnmpAdminString batteryIdentifier(2) +-- r-n SnmpAdminString batteryFirmwareVersion(3) +-- r-n Enumeration batteryType(4) +-- r-n Unsigned32 batteryTechnology(5) +-- r-n Unsigned32 batteryNominalVoltage(6) +-- r-n Unsigned32 batteryNumberOfCells(7) +-- r-n Unsigned32 batteryNominalCapacity(8) +-- r-n Unsigned32 batteryMaxChargingCurrent(9) +-- r-n Unsigned32 batteryTrickleChargingCurrent(10) +-- r-n Unsigned32 batteryActualCapacity(11) +-- r-n Unsigned32 batteryChargingCycleCount(12) +-- r-n DateAndTime batteryLastChargingCycleTime(13) +-- r-n Enumeration batteryChargingState(14) +-- r-n Unsigned32 batteryCurrentCharge(15) +-- r-n Unsigned32 batteryCurrentVoltage(16) +-- r-n Integer32 batteryCurrentCurrent(17) +-- r-n Integer32 batteryTemperature(18) +-- rwn Unsigned32 batteryLowAlarmCharge(19) +-- rwn Unsigned32 batteryLowAlarmVoltage(20) +-- rwn Unsigned32 batteryReplacementAlarmCapacity(21) +-- rwn Unsigned32 batteryReplacementAlarmCycles(22) +-- r-n Integer32 batteryHighAlarmTemperature(23) The third group of objects in this table (OIDs ending with 19-23) indicates thresholds which can be used to raise an alarm if a Quittek, et al. Expires January 8, 2012 [Page 5] Internet-Draft Battery MIB July 2011 property of the battery exceeds one of them. Raising an alarm may include sending a notification. The Battery MIB defines three notifications. One indicating a low battery charging state, one indicating an aged battery that may need to be replaced and one indicating the battery temperature to have risen above a predefined value. 4. Battery Technologies and Properties Static information in the batteryTable includes battery type and technology. The battery type distinguishes primary (not re- chargeable) batteries from secondary (re-chargeable) batteries and capacitors. The battery technology describes the actual technology of a battery, which typically is a chemical technology. Since battery technologies are subject of intensive research and massively used technologies are often replaced by successor technologies within an few years, the list of battery technologies was not chosen as a fixed list. Instead, IANA has created a registry for battery technologies at http://www.iana.org/assignments/eman where numbers are assigned to battery technologies (TBD). The table below shows battery technologies known today that are in commercial use with the numbers assigned to them by IANA. New entries can be added to the IANA registry if new technologies get developed or if missing technologies are identified. Note that there exists a huge number of battery types that are not listed in the IANA registry. Many of them are experimental or cannot be used in an economically useful way. New entries should be added to the IANA registry only if the respective technologies are in commercial use and relevant to standardized battery monitoring over the Internet. Quittek, et al. Expires January 8, 2012 [Page 6] Internet-Draft Battery MIB July 2011 +----------------------------+----------+ | battery technology | assigned | | | number | +----------------------------+----------+ | unknown | 1 | | other | 2 | | Zinc-carbon | 3 | | Zinc-chloride | 4 | | Oxy nickel hydroxide | 5 | | lithium-copper oxide | 6 | | lithium-iron disulfide | 7 | | lithium-manganese dioxide | 8 | | Zinc-air | 9 | | Silver-oxide | 10 | | Alkaline | 11 | | Lead acid | 12 | | Nickel-cadmium | 13 | | Nickel-metal hybride | 14 | | Nickel-zinc | 15 | | Lithium ion | 16 | | Lithium polymer | 17 | | Double layer capacitor | 18 | +----------------------------+----------+ The lifetime of a battery can be approximated using the measure of charging cycles. A commonly used definition of a charging cycle is the amount of discharge equal to the nominal capacity of the battery [SBS]. This means that a single charging cycle may include several steps of partial charging and discharging until the amount of discharging has reached the nominal capacity of the battery. After that the next charging cycle immediately starts. 5. Definitions BATTERY-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, Integer32, Unsigned32 FROM SNMPv2-SMI -- RFC2578 SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC3411 DateAndTime FROM SNMPv2-TC -- RFC2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; -- RFC2580 Quittek, et al. Expires January 8, 2012 [Page 7] Internet-Draft Battery MIB July 2011 batteryMIB MODULE-IDENTITY LAST-UPDATED "201106261200Z" -- 26 june 2010 ORGANIZATION "IETF EMAN Working Group" CONTACT-INFO "General Discussion: eman@ietf.org To Subscribe: http://www.ietf.org/mailman/listinfo/eman Archive: http://www.ietf.org/mail-archive/web/eman Editor: Juergen Quittek NEC Europe Ltd. NEC Laboratories Europe Kurfuersten-Anlage 36 69115 Heidelberg Germany Tel: +49 6221 4342-115 Email: quittek@neclab.eu" DESCRIPTION "This MIB module defines a set of objects for monitoring batteries of networked devices and of their components. Copyright (c) 2010 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info). This version of this MIB module is part of RFC yyyy; see the RFC itself for full legal notices." -- replace yyyy with actual RFC number & remove this notice -- Revision history REVISION "201106261200Z" -- 26 June 2010 DESCRIPTION "Initial version, published as RFC yyyy." -- replace yyyy with actual RFC number & remove this notice ::= { mib-2 zzz } -- zzz to be assigned by IANA. --****************************************************************** -- Top Level Structure of the MIB module Quittek, et al. Expires January 8, 2012 [Page 8] Internet-Draft Battery MIB July 2011 --****************************************************************** batteryNotifications OBJECT IDENTIFIER ::= { batteryMIB 0 } batteryObjects OBJECT IDENTIFIER ::= { batteryMIB 1 } batteryConformance OBJECT IDENTIFIER ::= { batteryMIB 2 } --================================================================== -- 1. Object Definitions --================================================================== -------------------------------------------------------------------- -- 1.1. Battery Table -------------------------------------------------------------------- batteryTable OBJECT-TYPE SYNTAX SEQUENCE OF BatteryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides information on batteries. It contains one conceptual row per battery." ::= { batteryObjects 1 } batteryEntry OBJECT-TYPE SYNTAX BatteryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry providing information on a battery." INDEX { batteryIndex } ::= { batteryTable 1 } BatteryEntry ::= SEQUENCE { batteryIndex Integer32, batteryIdentifier SnmpAdminString, batteryFirmwareVersion SnmpAdminString, batteryType INTEGER, batteryTechnology Unsigned32, batteryNominalVoltage Unsigned32, batteryNumberOfCells Unsigned32, batteryNominalCapacity Unsigned32, batteryMaxChargingCurrent Unsigned32, batteryTrickleChargingCurrent Unsigned32, batteryActualCapacity Unsigned32, batteryChargingCycleCount Unsigned32, batteryLastChargingCycleTime DateAndTime, batteryChargingState INTEGER, batteryCurrentCharge Unsigned32, Quittek, et al. Expires January 8, 2012 [Page 9] Internet-Draft Battery MIB July 2011 batteryCurrentVoltage Unsigned32, batteryCurrentCurrent Integer32, batteryTemperature Integer32, batteryLowAlarmCharge Unsigned32, batteryLowAlarmVoltage Unsigned32, batteryReplacementAlarmCapacity Unsigned32, batteryReplacementAlarmCycles Unsigned32, batteryHighAlarmTemperature Integer32 } batteryIndex OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies a battery for which status is reported. Index values MUST be locally unique. If there is an instance of the entPhysicalTable (defined in the ENTITY-MIB module, see RFC 4133) with an individual entry for each battery, then it is REQUIRED that values of batteryIndex match the corresponding values of entPhysicalIndex for the batteries. Otherwise, index values may be chosen arbitrarily." ::= { batteryEntry 1 } batteryIdentifier OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains an identifier for the battery. Many manufacturers deliver not pure batteries but battery packages including additional hardware and firmware. Typically, these modules include an identifier that can be retrieved by a device at which a battery has been installed. The identifier is useful when batteries are removed and re-installed at the same or other devices. Then the device or the network management system can trace batteries and achieve continuity of battery monitoring. If the battery identifier cannot be represented using the ISO/IEC IS 10646-1 character set, then a hexadecimal encoding of a binary representation of the battery identifier must be used. The value of this object must be an empty string if there Quittek, et al. Expires January 8, 2012 [Page 10] Internet-Draft Battery MIB July 2011 is no battery identifier or if the battery idenitfier is unknown." ::= { batteryEntry 2 } batteryFirmwareVersion OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the version number of the firmware that is included in a battery module. Many manufacturers deliver not pure batteries but battery packages including additional hardware and firmware. Since the bahavior of the battery may change with the firmware, it may be useful to retrieve the firmware version number. The value of this object must be an empty string if there is no firware or if the version number of the firware is unknown." ::= { batteryEntry 3 } batteryType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), primary(3), rechargeable(4), capacitor(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of battery. It distinguishes between primary (not re-chargeable) batteries, secondary (rechargeable) batteries and capacitors which are not really batteries but often used in the same way as a battery. The value other(1) can be used if the battery type is known but none of the ones above. Value unknown(2) is to be used if the type of battery cannot be determined." ::= { batteryEntry 4 } batteryTechnology OBJECT-TYPE SYNTAX Unsigned32 Quittek, et al. Expires January 8, 2012 [Page 11] Internet-Draft Battery MIB July 2011 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the technology used by the battery. Numbers identifying battery types are registered at IANA. A current list of assignments can be found at . Value 0 (unknown) MUST be used if the type of battery cannot be determined. Value 1 (other) can be used if the battery type is known but not one of the types already registered at IANA." ::= { batteryEntry 5 } batteryNominalVoltage OBJECT-TYPE SYNTAX Unsigned32 UNITS "millivolt" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the nominal voltage of the battery in units of millivolt (mV). Note that the nominal voltage is a constant value and typically different from the actual voltage of the battery. A value of 0 indicates that the nominal voltage is unknown." ::= { batteryEntry 6 } batteryNumberOfCells OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of cells contained in the battery. A value of 0 indicates that the number of cells is unknown." ::= { batteryEntry 7 } batteryNominalCapacity OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere hours" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the nominal capacity of the battery Quittek, et al. Expires January 8, 2012 [Page 12] Internet-Draft Battery MIB July 2011 in units of milliampere hours (mAh). Note that the nominal capacity is a constant value and typically different from the actual capacity of the battery. A value of 0 indicates that the nominal capacity is unknown." ::= { batteryEntry 8 } batteryMaxChargingCurrent OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the maximal current to be used for charging the battery in units of milliampere (mA). Note that the maximal charging current may not lead to optimal charge of the battery and that some batteries can only be charged with the maximal current for a limited amount of time. A value of 0 indicates that the maximal charging current is unknown." ::= { batteryEntry 9 } batteryTrickleChargingCurrent OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the recommended current to be used for trickle charging the battery in units of milliampere (mA). Typically, this is a value recommended by the manufacturer of the battery or by the manufacturer of the charging circuit. A value of 0 indicates that the recommended trickle charging current is unknown." ::= { batteryEntry 10 } batteryActualCapacity OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere hours" MAX-ACCESS read-only Quittek, et al. Expires January 8, 2012 [Page 13] Internet-Draft Battery MIB July 2011 STATUS current DESCRIPTION "This object provides the actual capacity of the battery in units of milliampere hours (mAh). Note that the actual capacity needs to be measured and is typically an estimate based on observed discharging and charging cycles of the battery. A value of 'ffffffff'H indicates that the actual capacity cannot be determined." ::= { batteryEntry 11 } batteryChargingCycleCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the number of completed charging cycles that that the battery underwent. In line with the Smart Battery Data Specification Revision 1.1, a charging cycle is defined as the process of discharging the battery by a total amount equal to the battery nominal capacity as given by object batteryNominalCapacity. A charging cycle may include several steps of charging and discharging the battery until the discharging amount given by batteryNominalCapacity has been reached. As soon as a charging cycle has been completed the next one starts immediately independent of the battery's current charge at the end of the cycle. For batteries of type primary(1) the value of this object is always 0. A value of 'ffffffff'H indicates that the number of charging cycles cannot be determined." ::= { batteryEntry 12 } batteryLastChargingCycleTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time of the last charging cycle. The value '0000000000000000'H is returned if the battery has not been charged yet or if the last charging time cannot be determined. Quittek, et al. Expires January 8, 2012 [Page 14] Internet-Draft Battery MIB July 2011 For batteries of type primary(1) the value of this object is always '0000000000000000'H." ::= { batteryEntry 13 } batteryChargingState OBJECT-TYPE SYNTAX INTEGER { unknown(1), charging(2), maintainingCharge(3), noCharging(4), discharging(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the current charging state of the battery. Value unknown(1) indicates that the charging state of the battery cannot be determined. Value charging(2) indicates that the battery is being charged in a way that the charge of the battery increases. Value maintainingCharge(3) indicates that the battery is being charged with a low current that compensates self-discharging. This includes trickle charging, float charging and other methods for maintaining the current charge of a battery. Value noCharging(4) indicates that the battery is not charged or discharged by electric current between the battery and electric circuits external to the battery. Note that the battery may still be subject to self-discharging. Value discharging(5) indicates that the battery is being discharged and that the charge of the battery decreases." ::= { batteryEntry 14 } batteryCurrentCharge OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere hours" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the current charge of the battery in units of milliampere hours (mAh). Quittek, et al. Expires January 8, 2012 [Page 15] Internet-Draft Battery MIB July 2011 Note that the current charge needs to be measured and is typically an estimate based on observed discharging and charging cycles of the battery. A value of 'ffffffff'H indicates that the current charge cannot be determined." ::= { batteryEntry 15 } batteryCurrentVoltage OBJECT-TYPE SYNTAX Unsigned32 UNITS "millivolt" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the current voltage of the battery in units of millivolt (mV). A value of 'ffffffff'H indicates that the current voltage cannot be determined." ::= { batteryEntry 16 } batteryCurrentCurrent OBJECT-TYPE SYNTAX Integer32 UNITS "milliampere" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the current charging or discharging current of the battery in units of milliampere (mA). Charging current is represented by positive values, discharging current is represented by negative values. A value of '7fffffff'H indicates that the current current cannot be determined." ::= { batteryEntry 17 } batteryTemperature OBJECT-TYPE SYNTAX Integer32 UNITS "degrees Celsius" MAX-ACCESS read-only STATUS current DESCRIPTION "The ambient temperature at or near the battery. A value of '7fffffff'H indicates that the temperature cannot be determined." ::= { batteryEntry 18 } Quittek, et al. Expires January 8, 2012 [Page 16] Internet-Draft Battery MIB July 2011 batteryLowAlarmCharge OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere hours" MAX-ACCESS read-write STATUS current DESCRIPTION "This object provides the lower threshold value for object batteryCurrentCharge. If the value of object batteryCurrentCharge falls below this threshold, a low battery alarm will be raised. The alarm procedure may include generating a batteryLowNotification. A value of 0 indicates that no alarm will be raised for any value of object batteryCurrentCharge." ::= { batteryEntry 19 } batteryLowAlarmVoltage OBJECT-TYPE SYNTAX Unsigned32 UNITS "millivolt" MAX-ACCESS read-write STATUS current DESCRIPTION "This object provides the lower threshold value for object batteryCurrentVoltage. If the value of object batteryCurrentVoltage falls below this threshold, a low battery alarm will be raised. The alarm procedure may include generating a batteryLowNotification. A value of 0 indicates that no alarm will be raised for any value of object batteryCurrentVoltage." ::= { batteryEntry 20 } batteryReplacementAlarmCapacity OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere hours" MAX-ACCESS read-write STATUS current DESCRIPTION "This object provides the lower threshold value for object batteryActualCapacity. If the value of object batteryActualCapacity falls below this threshold, a battery aging alarm will be raised. The alarm procedure may include generating a batteryAgingNotification. A value of 0 indicates that no alarm will be raised for any value of object batteryActualCapacity." ::= { batteryEntry 21 } Quittek, et al. Expires January 8, 2012 [Page 17] Internet-Draft Battery MIB July 2011 batteryReplacementAlarmCycles OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliampere hours" MAX-ACCESS read-write STATUS current DESCRIPTION "This object provides the upper threshold value for object batteryChargingCycleCount. If the value of object batteryChargingCycleCount rises above this threshold, a battery aging alarm will be raised. The alarm procedure may include generating a batteryAgingtNotification. A value of 0 indicates that no alarm will be raised for any value of object batteryChargingCycleCount." ::= { batteryEntry 22 } batteryHighAlarmTemperature OBJECT-TYPE SYNTAX Integer32 UNITS "degrees Celsius" MAX-ACCESS read-only STATUS current DESCRIPTION "This object provides the upper threshold value for object batteryTemperature. If the value of object batteryTemperature rises above this threshold, a battery high temperature alarm will be raised. The alarm procedure may include generating a batteryHighTemperatNotification. A value of '7fffffff'H indicates that no alarm will be raised for any value of object batteryCurrentCharge." ::= { batteryEntry 23 } --================================================================== -- 2. Notifications --================================================================== batteryLowNotification NOTIFICATION-TYPE OBJECTS { batteryCurrentCharge, batteryCurrentVoltage } STATUS current DESCRIPTION "This notification can be generated when the current charge (batteryCurrentCharge) or the current voltage (batteryCurrentVoltage) of the battery falls below a threshold defined by object batteryLowAlarmCharge or Quittek, et al. Expires January 8, 2012 [Page 18] Internet-Draft Battery MIB July 2011 object batteryLowAlarmVoltage, respectively." ::= { batteryNotifications 1 } batteryAgingNotification NOTIFICATION-TYPE OBJECTS { batteryActualCapacity, batteryChargingCycleCount } STATUS current DESCRIPTION "This notification can be generated when the actual capacity (batteryActualCapacity) falls below a threshold defined by object batteryReplacementAlarmCapacity or when the charging cycle count of the battery (batteryChargingCycleCount) exceeds the threshold defined by object batteryReplacementAlarmCycles." ::= { batteryNotifications 2 } batteryHighTemperatNotification NOTIFICATION-TYPE OBJECTS { batteryTemperature } STATUS current DESCRIPTION "This notification can be generated when the actual temperature (batteryTemperature) rises above a threshold defined by object batteryHighAlarmTemperature." ::= { batteryNotifications 3 } --================================================================== -- 3. Conformance Information --================================================================== batteryCompliances OBJECT IDENTIFIER ::= { batteryConformance 1 } batteryGroups OBJECT IDENTIFIER ::= { batteryConformance 2 } -------------------------------------------------------------------- -- 3.1. Compliance Statements -------------------------------------------------------------------- batteryCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for implementations of the POWER-STATE-MIB module. A compliant implementation MUST implement the objects Quittek, et al. Expires January 8, 2012 [Page 19] Internet-Draft Battery MIB July 2011 defined in the mandatory groups batteryDescriptionGroup and batteryStatusGroup." MODULE -- this module MANDATORY-GROUPS { batteryDescriptionGroup, batteryStatusGroup } GROUP batteryAlarmThresholdsGroup DESCRIPTION "A compliant implementation does not have to implement the batteryAlarmThresholdsGroup." GROUP batteryNotificationsGroup DESCRIPTION "A compliant implementation does not have to implement the batteryNotificationsGroup." ::= { batteryCompliances 1 } -------------------------------------------------------------------- -- 3.2. MIB Grouping -------------------------------------------------------------------- batteryDescriptionGroup OBJECT-GROUP OBJECTS { batteryIdentifier, batteryFirmwareVersion, batteryType, batteryTechnology, batteryNominalVoltage, batteryNumberOfCells, batteryNominalCapacity, batteryMaxChargingCurrent, batteryTrickleChargingCurrent } STATUS current DESCRIPTION "A compliant implementation MUST implement the objects contained in this group." ::= { batteryGroups 1 } batteryStatusGroup OBJECT-GROUP OBJECTS { batteryActualCapacity, batteryChargingCycleCount, batteryLastChargingCycleTime, batteryChargingState, batteryCurrentCharge, batteryCurrentVoltage, batteryCurrentCurrent, Quittek, et al. Expires January 8, 2012 [Page 20] Internet-Draft Battery MIB July 2011 batteryTemperature } STATUS current DESCRIPTION "A compliant implementation MUST implement the objects contained in this group." ::= { batteryGroups 2 } batteryAlarmThresholdsGroup OBJECT-GROUP OBJECTS { batteryLowAlarmCharge, batteryLowAlarmVoltage, batteryReplacementAlarmCapacity, batteryReplacementAlarmCycles, batteryHighAlarmTemperature } STATUS current DESCRIPTION "A compliant implementation does not have to implement the object contained in this group." ::= { batteryGroups 3 } batteryNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { batteryLowNotification, batteryAgingNotification, batteryHighTemperatNotification } STATUS current DESCRIPTION "A compliant implementation does not have to implement the notification contained in this group." ::= { batteryGroups 4 } END 6. Security Considerations This sections needs to be updated after changing four managed objects from read-only to read-write. There are no management objects defined in this MIB module that have a MAX-ACCESS clause of read-write and/or read-create. So, if this MIB module is implemented correctly, then there is no risk that an intruder can alter or create any management objects of this MIB module via direct SNMP SET operations. Some of the readable objects in this MIB module (i.e., objects with a Quittek, et al. Expires January 8, 2012 [Page 21] Internet-Draft Battery MIB July 2011 MAX-ACCESS other than not-accessible) may be considered sensitive or vulnerable in some network environments. It is thus important to control even GET and/or NOTIFY access to these objects and possibly to even encrypt the values of these objects when sending them over the network via SNMP. These are the tables and objects and their sensitivity/vulnerability: o This list is still to be done. SNMP versions prior to SNMPv3 did not include adequate security. Even if the network itself is secure (for example by using IPsec), even then, there is no control as to who on the secure network is allowed to access and GET/SET (read/change/create/delete) the objects in this MIB module. It is RECOMMENDED that implementers consider the security features as provided by the SNMPv3 framework (see [RFC3410], section 8), including full support for the SNMPv3 cryptographic mechanisms (for authentication and privacy). Further, deployment of SNMP versions prior to SNMPv3 is NOT RECOMMENDED. Instead, it is RECOMMENDED to deploy SNMPv3 and to enable cryptographic security. It is then a customer/operator responsibility to ensure that the SNMP entity giving access to an instance of this MIB module is properly configured to give access to the objects only to those principals (users) that have legitimate rights to indeed GET or SET (change/create/delete) them. 7. IANA Considerations 7.1. SMI Object Identifier Registration The Battery MIB module defined in this document uses the following IANA-assigned OBJECT IDENTIFIER value recorded in the SMI Numbers registry: Descriptor OBJECT IDENTIFIER value ---------- ----------------------- batteryMIB { mib-2 xxx } [NOTE for IANA: Please allocate an object identifier at http://www.iana.org/assignments/smi-numbers for object batteryMIB.] 7.2. Battery Technology Registration Object batteryTechnology defined in Section 5 reports battery technologies. 18 values for battery technologies have initially been Quittek, et al. Expires January 8, 2012 [Page 22] Internet-Draft Battery MIB July 2011 defined. They are listed in a table in Section 4. For ensuring extensibility of this list, IANA has created a registry for battery technologies at http://www.iana.org/assignments/eman and filled it with the initial list given in Section 4. New assignments of numbers for battery technologies will be administered by IANA through Expert Review ([RFC5226]). Experts must check for sufficient relevance of a battery technology to be added. [NOTE for IANA: Please create a new registry under http://www.iana.org/assignments/eman for battery types. Please fill the registry with values from the table in Section 4] 8. Open Issues 8.1. Writable Notification thresholds Do we want to have the thresholds for sending notifications (batteryLowAlarmPercentage, batteryLowAlarmVoltage, batteryReplacementAlarmCapacity, batteryReplacementAlarmCycles) to be read-write or read-only? 8.2. Re-arming batteryLowNotification What needs to happen after sending a batteryLowNotification before another batteryLowNotification can be sent for the same battery? 8.3. Alignment with the Smart Battery Data Specification How closely do we need to align with the Smart Battery Data Specification [SBS]? 9. Acknowledgements We would like to thank Steven Chew for his input. 10. References 10.1. Normative References [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. [RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an Quittek, et al. Expires January 8, 2012 [Page 23] Internet-Draft Battery MIB July 2011 IANA Considerations Section in RFCs", BCP 26, RFC 5226, May 2008. [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Structure of Management Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999. [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J. Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD 58, RFC 2579, April 1999. [RFC2580] McCloghrie, K., Perkins, D., and J. Schoenwaelder, "Conformance Statements for SMIv2", STD 58, RFC 2580, April 1999. [RFC4133] Bierman, A. and K. McCloghrie, "Entity MIB (Version 3)", RFC 4133, August 2005. 10.2. Informative References [I-D.ietf-eman-requirements] Quittek, J., Winter, R., Dietz, T., Claise, B., and M. Chandramouli, "Requirements for Energy Management", draft-ietf-eman-requirements-03 (work in progress), June 2011. [I-D.ietf-eman-framework] Claise, B., Parello, J., and L. Silver, "Energy Management Framework", draft-ietf-eman-framework-01 (work in progress), March 2011. [RFC1628] Case, J., "UPS Management Information Base", RFC 1628, May 1994. [RFC3410] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction and Applicability Statements for Internet- Standard Management Framework", RFC 3410, December 2002. [SBS] "Smart Battery Data Specification", Revision 1.1, December 1998. Quittek, et al. Expires January 8, 2012 [Page 24] Internet-Draft Battery MIB July 2011 Authors' Addresses Juergen Quittek NEC Europe Ltd. NEC Laboratories Europe Network Research Division Kurfuersten-Anlage 36 Heidelberg 69115 DE Phone: +49 6221 4342-115 Email: quittek@neclab.eu Rolf Winter NEC Europe Ltd. NEC Laboratories Europe Network Research Division Kurfuersten-Anlage 36 Heidelberg 69115 DE Phone: +49 6221 4342-121 Email: Rolf.Winter@neclab.eu Thomas Dietz NEC Europe Ltd. NEC Laboratories Europe Network Research Division Kurfuersten-Anlage 36 Heidelberg 69115 DE Phone: +49 6221 4342-128 Email: Thomas.Dietz@neclab.eu Quittek, et al. Expires January 8, 2012 [Page 25]